betaFeedback

WorksEngineering

Fundamental Limits and Joint Design for Monostatic Joint Communications and Sensing in LEO Satellites

Abstract

Monostatic joint communication and sensing (JCAS) from a low-Earth-orbit (LEO) satellite requires full-duplex (FD) operation, with self-interference (SI) 8080–100100~dB stronger than the ground echo. The echo returns milliseconds after transmission, whereas the onboard coupling spans a few symbols. We develop a theory and a design that exploit this separation. Restricting the analog and digital cancellers to the short SI support is without loss of optimality and essential in practice: a least-squares canceller whose support contains the target delay absorbs the coherent echo and reduces the radar SINR by a closed-form factor, about 1818~dB for a vessel at its zero-Doppler crossing. Modeling the SI that no linear canceller can reconstruct as spatially white and accounting for ADC quantization, we derive in closed form a ceiling on the radar SINR, the minimum pre-ADC SI power under a canceller tap budget, the budget for full cancellation, and the sensing weight at which the optimal design changes over from communication to sensing. We then maximize a weighted sum of the communication and sensing SINRs, each normalized by its half-duplex benchmark, over the beamformers, sensing covariance, combiners, and cancellers for KK users and QQ targets, using an alternating algorithm with closed-form updates. Simulations confirm the closed forms. The joint design gains up to 13%13\% in the normalized objective over a sequential design that cancels the SI only at the receiver, and more than 1010~dB of downlink and radar SINR with 44-bit ADCs and in the 10th-percentile worst-target SINR of four targets, whereas ignoring the SI overloads the ADCs.

Introduction

Joint communication and sensing (JCAS), also referred to as integrated sensing and communication, has become a defining capability of sixth-generation networks: a single platform, spectrum, and waveform deliver information and probe the environment at the same time [1, 2, 3, 4]. Non-terrestrial networks are a natural host for this integration [5, 6]. A low-Earth-orbit (LEO) satellite carries a high-gain payload that already covers a wide area from a known position, so the same hardware can provide broadband connectivity and wide-area sensing for maritime surveillance, disaster monitoring, or infrastructure inspection without duplicating radio-frequency (RF) chains or spectral resources. In a monostatic implementation, however, the satellite must receive the ground echo while it transmits the downlink over the same time-frequency resources. This is full-duplex (FD) operation [7, 8], and the sensing receiver is exposed to the self-interference (SI) generated by the onboard transmitter, which exceeds the echo of a large vessel by 80–100 dB after passive isolation.

State of the Art

FD JCAS has been studied mainly for terrestrial base stations, from FD orthogonal frequency-division multiplexing (OFDM) radar measurements [9] to the design of beamformers for FD sensing at millimeter waves [10], waveforms [11], joint transmit and receive beamformers [12], joint beamforming and power allocation [13], and hybrid architectures [14]. These works model the SI as a short-memory channel whose residual is proportional to the transmit power and treat the target return as contemporaneous with the SI. They rely on the FD cancellation chain of passive suppression [15], analog and digital cancellation with limited dynamic range [16, 17, 18], spatial suppression [19], and beamforming-based cancellation at millimeter waves [20, 21, 22], and on dual-function waveform and beamforming design without FD constraints [23, 24, 25, 26, 27, 28]. For satellites, the literature is at the stage of feasibility studies and surveys: FD satellite communications are analyzed in [29], JCAS for satellite systems is surveyed in [5], and massive multiple-input multiple-output (MIMO) LEO downlinks are designed in [30]. On the optimization side, fractional objectives are handled by the quadratic transform [31, 32], and block-coordinate schemes converge under mild conditions [33, 34].

Research Gap

Three questions that decide whether monostatic JCAS in space is viable remain open. First, no model separates the delayed echo-generating signal from the contemporaneous SI-generating signal, so the effect of the delay structure on canceller estimation, in particular echo absorption, is unknown. Second, the limits that the SI imposes on spaceborne sensing are not established: how close the radar signal-to-interference-plus-noise ratio (SINR) can come to its half-duplex value given the non-reconstructible SI and finite analog-to-digital converter (ADC) resolution, which tap budget suffices, and when the payload should switch from communication to sensing. Third, no design jointly optimizes the beamformers, the sensing covariance, the combiners of several targets, and the analog and digital cancellers under the constraints of a satellite payload, and the gain over handling the SI at the receiver only is unknown.

Contributions

This paper answers these questions and thereby lays the foundations of monostatic JCAS in space. It extends our conference contribution, which introduced the delay-selective architecture for a single target, as follows:

  • Model. We develop a single-carrier FD LEO JCAS model with KK users and QQ monostatic targets that makes this separation explicit, describes the coupling by pulse-sampled path responses on a two-sided delay support, and accounts for the motion-induced echo phase, the non-reconstructible SI, and ADC quantization (§ 2).

  • Fundamental limits. We prove that delay-selective cancellers are without loss of optimality (Proposition 1), quantify in closed form the echo absorption of a least-squares canceller whose support contains the target delay (Lemma 1, Corollary 1), and derive closed forms for the radar SINR ceiling under spatially white non-reconstructible SI, together with a bound for correlated SI (Proposition 2), the minimum pre-ADC SI power and the tap budget for full cancellation (Lemma 2, Corollary 2), and the communication–sensing change-over weight (Proposition 3) (Section III).

  • Joint design. We maximize the communication and sensing sum-SINRs, each normalized by its half-duplex benchmark and weighted by one scalar per function, over the beamformers, sensing covariance, QQ combiners, and both cancellers under power, tap-norm, and pre-ADC constraints by an alternating algorithm with closed-form blocks; both canceller updates and Lemma 2 are instances of one generalized Sylvester solution (Lemma 3), and the monotone convergence of the objective and the complexity are established (Sections IV and § 5).

  • Evaluation. With a complete Ka-band link budget, we confirm the closed forms, including the echo loss by a time-domain least-squares Monte Carlo, and compare the joint design with half-duplex references and with a sequential design that optimizes the cancellers for the SI-free beamformers, with an SI-unaware design as an infeasible reference, under tap budgets, low-resolution ADCs, quantized analog taps, and multiple targets (Section VI).

Notation

Bold letters denote vectors and matrices; (⋅)H(\cdot)^{H} and (⋅)†(\cdot)^{\dagger} denote Hermitian transpose and Moore–Penrose inverse; tr⁡(⋅)\operatorname{tr}(\cdot), ∥⋅∥2\lVert\cdot\rVert_{2}, and ∥⋅∥F\lVert\cdot\rVert_{F} are the trace, Euclidean and Frobenius norms; IN\mathbf{I}_{N} is the N×NN \times N identity; δn,m\delta_{n,m} is the Kronecker delta; CN(0,R)\mathcal{CN}(0,\mathbf{R}) is the circularly symmetric complex Gaussian distribution; E{⋅}\mathbb{E}\{\cdot\} and R{⋅}\mathfrak{R}\{\cdot\} are expectation and real part; ⪰\succeq is the Loewner order; and sinc⁡(x)=sin⁡(πx)/(πx)\operatorname{sinc}(x)=\sin(\pi x)/(\pi x).

System Model

We consider an FD LEO satellite that serves KK single-antenna ground users and senses QQ ground targets in a monostatic configuration. The satellite has NtN_t transmit and NrN_r sensing receive antennas (ports of a subarrayed panel), mounted on the same rigid platform. A single-carrier waveform is shared by the communication and sensing functions; it is preferred for its low peak-to-average power ratio at the power-limited satellite amplifier and because the delay separation is explicit at the symbol rate. The support restriction developed below applies equally to the time-domain cancellers of an OFDM transceiver. Figure 1 illustrates the scenario, the receiver, and the delay structure that the design exploits.

System overview

Figure 1. System overview. (a) Monostatic FD JCAS from a LEO satellite: the downlink beams serve the users and illuminate the target, whose echo returns after τq≈2.3 ms\tau_q \approx2.3\ \mathrm{ms}, while the transmit–receive coupling produces SI. (b) Delay-selective receiver: the analog and digital cancellers reconstruct the SI from x[n]\mathbf{x}[n] on the short-delay support DSI\mathcal{D}_{\mathrm{SI}}, and only the range-compression reference is delayed by dqd_q. (c) Delay structure: the SI taps occupy DSI\mathcal{D}_{\mathrm{SI}} around d=0d=0, the echo lies at dq≈4.6×104d_q \approx4.6 \times10^4; a canceller whose support contains dqd_q absorbs the echo (Lemma 1).

Transmit and Communication Models

Let K={1,…,K}\mathcal{K}=\{1,\ldots,K\} denote the user set. At symbol time nn, the satellite transmits

x[n]=∑k=1Kwksk[n]+v[n],(1)\mathbf{x}[n]=\sum_{k=1}^{K}\mathbf{w}_{k}s_{k}[n]+\mathbf{v}[n], \tag*{(1)}

where wk∈CNt\mathbf{w}_{k}\in\mathbb{C}^{N_t} is the beamformer of user kk, sk[n]s_{k}[n] is its information symbol, and v[n]∈CNt\mathbf{v}[n]\in\mathbb{C}^{N_t} is an optional dedicated sensing signal. The symbols are temporally white and mutually independent, E{sk[n]sj∗[m]}=δk,jδn,m\mathbb{E}\{s_{k}[n]s_{j}^{*}[m]\}=\delta_{k,j}\delta_{n,m}, and the sensing signal satisfies E{v[n]vH[m]}=Rsδn,m\mathbb{E}\{\mathbf{v}[n]\mathbf{v}^{H}[m]\}=\mathbf{R}_{s}\delta_{n,m}, Rs⪰0\mathbf{R}_{s}\succeq0, independently of the symbols. The transmit covariance is

Rx=E{x[n]xH[n]}=∑k=1KwkwkH+Rs.(2)\mathbf{R}_{x}=\mathbb{E}\{\mathbf{x}[n]\mathbf{x}^{H}[n]\}=\sum_{k=1}^{K}\mathbf{w}_{k}\mathbf{w}_{k}^{H}+\mathbf{R}_{s}. \tag*{(2)}

The sequence x[n]\mathbf{x}[n] is pulse-shaped with a fixed root-raised-cosine (RRC) pulse p(t)p(t) of symbol period TsT_s, which is known and not optimized. After timing and Doppler compensation, user kk receives

yk[n]=hkHwksk[n]+∑j≠khkHwjsj[n]+hkHv[n]+nk[n],(3)y_{k}[n]=\mathbf{h}_{k}^{H}\mathbf{w}_{k}s_{k}[n]+\sum_{j\ne k}\mathbf{h}_{k}^{H}\mathbf{w}_{j}s_{j}[n]+\mathbf{h}_{k}^{H}\mathbf{v}[n]+n_{k}[n], \tag*{(3)}

where hk∈CNt\mathbf{h}_{k}\in\mathbb{C}^{N_t} is the effective satellite-to-user channel and nk[n]∼CN(0,σk2)n_{k}[n]\sim\mathcal{CN}(0,\sigma_{k}^{2}). The communication SINR is

γk=∣hkHwk∣2∑j≠k∣hkHwj∣2+hkHRshk+σk2.(4)\gamma_{k}=\frac{\lvert\mathbf{h}_{k}^{H}\mathbf{w}_{k}\rvert^{2}}{\sum_{j\ne k}\lvert\mathbf{h}_{k}^{H}\mathbf{w}_{j}\rvert^{2}+\mathbf{h}_{k}^{H}\mathbf{R}_{s}\mathbf{h}_{k}+\sigma_{k}^{2}}. \tag*{(4)}

Delayed Target Echoes and SI Channel

Target q∈Q={1,…,Q}q\in\mathcal{Q}=\{1,\ldots,Q\} has round-trip delay τq\tau_{q}, integer symbol delay dq=⌊τq/Ts⌋d_{q}=\lfloor\tau_{q}/T_{s}\rfloor, and fractional delay δq=τq−dqTs\delta_{q}=\tau_{q}-d_{q}T_{s}, ∣δq∣≤Ts/2\lvert\delta_{q}\rvert\le T_{s}/2, whose effect is a known amplitude factor absorbed into βq\beta_{q} (§ 2-D). The delay τq\tau_{q} is predicted from the satellite ephemeris and the target position provided by a preceding detection or tracking stage, or it is a hypothetical range bin in search mode; the design below requires only dq∉DSId_{q}\notin\mathcal{D}_{\mathrm{SI}} and is otherwise independent of dqd_{q}, so that errors in τq\tau_{q} do not affect it. Within a coherent processing interval (CPI) of duration TCPIT_{\mathrm{CPI}}, dqd_{q} is held fixed, which requires the range walk to stay below half a symbol, ∣r˙q∣<cTs/(4TCPI)\lvert\dot{r}_{q}\rvert<cT_{s}/(4T_{\mathrm{CPI}}); this holds near the zero-Doppler instant and, otherwise, after ephemeris-based range-migration compensation. The fast phase variation is retained explicitly.

The target channel is modeled as

Hq=βqar(θq)atH(θq)∈CNr×Nt,∣βq∣2=ψp2(δq)Ge2λc2(4π)3Rq4La2.(5)\mathbf{H}_q=\beta_q\mathbf{a}_r(\theta_q)\mathbf{a}_t^{H}(\theta_q)\in\mathbb{C}^{N_r\times N_t},\qquad|\beta_q|^2=\frac{\psi_p^2(\delta_q)G_e^2\lambda_c^2}{(4\pi)^3R_q^4L_a^2}. \tag*{(5)}

which collects the two-way propagation loss over the slant range RqR_q, the atmospheric loss LaL_a, the port gain GeG_e, and the straddle factor ψp2(δq)≤1\psi_p^2(\delta_q)\leq1 defined below, while at(θq)\mathbf{a}_t(\theta_q) and ar(θq)\mathbf{a}_r(\theta_q) are the transmit and receive steering vectors toward the target. The reflection coefficient ρq\rho_q satisfies E{ρq}=0\mathbb{E}\{\rho_q\}=0 and E{∣ρq∣2}=σq2\mathbb{E}\{|\rho_q|^2\}=\sigma_q^2, where σq2\sigma_q^2 is the radar cross section (RCS). Satellite motion produces the deterministic carrier phase

ϕq[n]=exp⁡(−j2πfcτq(nTs)),(6)\phi_q[n]=\exp\left(-j2\pi f_c\tau_q(nT_s)\right), \tag*{(6)}

References

  1. [1]F. Liu, Y. Cui, C. Masouros, J. Xu, T. X. Han, Y. C. Eldar, and S. Buzzi, “Integrated sensing and communications: Toward dual-functional wireless networks for 6G and beyond,” IEEE J. Sel. Areas Commun., vol. 40, no. 6, pp. 1728–1767, 2022.DOI
  2. [2]A. A. Zhang, F. Liu, C. Masouros, R. W. Heath, Z. Feng, L. Zheng, and A. Petropulu, “An overview of signal processing techniques for joint communication and radar sensing,” IEEE J. Sel. Topics Signal Process., vol. 15, no. 6, pp. 1295–1315, 2021.DOI
  3. [3]F. Liu, C. Masouros, A. P. Petropulu, H. Griffiths, and L. Hanzo, “Joint radar and communication design: Applications, state-of-the-art, and the road ahead,” IEEE Trans. Commun., vol. 68, no. 6, pp. 3834–3862, 2020.arxiv.org/abs/1906.00789
  4. [4]C. Sturm and W. Wiesbeck, “Waveform design and signal processing aspects for fusion of wireless communications and radar sensing,” Proc. IEEE, vol. 99, no. 7, pp. 1236–1259, 2011.DOI
  5. [5]C. K. Sheemar, J. Querol, W. U. Khan, P. Thiruvasagam, S. Solanki, I. Edjekouane, A. Gonzalez-Garrido, M. Al-Ansi, C. E. Garcia, and S. Chatzinotas, “Joint communications, sensing, and positioning in 6G multi-functional satellite systems: Survey and open challenges,” arXiv preprint arXiv:2509.25937, 2025.arxiv.org/abs/2509.25937
  6. [6]O. Khedrli, E. Lagunas, N. Maturo, S. K. Sharma, B. Shankar, J. F. M. Montoya, J. C. M. Duncan, D. Spano, S. Chatzinotas, K. Kisseliff, J. Querol, L. Lei, T. X. Vu, and G. Goussestis, “Satellite communications in the new space era: A survey and future challenges,” IEEE Commun. Surveys Tuts., vol. 23, no. 1, pp. 70–109, 2021.
  7. [7]C. K. Sheemar, S. Solanki, G. C. Alexandropoulos, E. Lagunas, J. Querol, S. Chatzinotas, and B. Ottersten, “Full duplex joint communications and sensing for 6G: Opportunities and challenges,” arXiv preprint arXiv:2308.07266, 2023.
  8. [8]A. Sahabalarwal, P. Schnitter, D. Guo, D. W. Bliss, S. Rangarajan, and R. Wichman, “In-band full-duplex wireless: Challenges and opportunities,” IEEE J. Sel. Areas Commun., vol. 32, no. 9, pp. 1637–1652, 2014.
  9. [9]C. B. Barneto, T. Riihonen, S. D. Liyanarachchi, M. Heino, N. González-Prelcic, and M. Valkama, “Full-duplex OFDM radar with LTE and 5G NR waveforms: Challenges, solutions, and measurements,” IEEE Trans. Microw. Theory Techn., vol. 67, no. 10, pp. 4042–4054, 2019.DOI
  10. [10]C. B. Barneto, T. Riihonen, S. D. Liyanarachchi, M. Heino, N. González-Prelcic, and M. Valkama, “Beamformer design and optimization for joint communication and full-duplex sensing at mm-waves,” IEEE Trans. Commun., vol. 70, no. 12, pp. 8298–8312, 2022.
  11. [11]Z. Xiao and Y. Zeng, “Waveform design and performance analysis for full-duplex integrated sensing and communication,” IEEE J. Sel. Areas Commun., vol. 40, no. 6, pp. 1823–1837, 2022.
  12. [12]Z. Liu, S. Aditya, H. Li, and B. Clerckx, “Joint transmit and receive beamforming design in full-duplex integrated sensing and communications,” IEEE J. Sel. Areas Commun., vol. 41, no. 9, pp. 2907–2919, 2023.arxiv.org/abs/2210.10904
  13. [13]Z. He, W. Xu, H. Shen, D. W. K. Ng, Y. C. Eldar, and X. You, “Full-duplex communication for ISAC: Joint beamforming and power optimization,” IEEE J. Sel. Areas Commun., vol. 41, no. 9, pp. 2920–2936, 2023.arxiv.org/abs/2211.00229
  14. [14]M. A. Islam, G. C. Alexandropoulos, and B. Smida, “Integrated sensing and communication with millimeter wave full duplex hybrid beamforming,” in Proc. IEEE Int. Conf. Commun. (ICC), May 2022, pp. 4673–4678.arxiv.org/abs/2201.05240
  15. [15]E. Everett, A. Sahai, and A. Sabharwal, “Passive self-interference suppression for full-duplex infrastructure nodes,” IEEE Trans. Wireless Commun., vol. 13, no. 2, pp. 680–694, 2014.DOI
  16. [16]B. P. Day, A. R. Margetts, D. W. Bliss, and P. Schniter, “Full-duplex MIMO relaying: Achievable rates under limited dynamic range,” IEEE J. Sel. Areas Commun., vol. 30, no. 8, pp. 1541–1553, 2012.
  17. [17]T. Riihonen and R. Wichman, “Analog and digital self-interference cancellation in full-duplex MIMO-OFDM transceivers with limited resolution in A/D conversion,” in Proc. Asilomar Conf. Signals, Syst., Comput., 2012, pp. 45–49.DOI
  18. [18]D. Bharadia, E. McMilin, and S. Katti, “Full duplex radios,” in Proc. ACM SIGCOMM, 2013, pp. 375–386.
  19. [19]T. Riihonen, S. Werner, and R. Wichman, “Mitigation of loopback self-interference in full-duplex MIMO relays,” IEEE Trans. Signal Process., vol. 59, no. 12, pp. 5983–5993, 2011.DOI
  20. [20]I. P. Roberts, J. G. Andrews, H. B. Jain, and S. Vishwanath, “Millimeter-wave full duplex radios: New challenges and techniques,” IEEE Wireless Commun., vol. 28, no. 1, pp. 36–43, 2021.arxiv.org/abs/2009.06048
  21. [21]K. Satyanarayana, M. El-Hajjar, P.-H. Kuo, A. Mourad, and L. Hanzo, “Hybrid beamforming design for full-duplex millimeter wave communication,” IEEE Trans. Veh. Technol., vol. 68, no. 2, pp. 1394–1404, 2019.
  22. [22]C. K. Sheemar, C. K. Thomas, and D. Slock, “Practical hybrid beamforming for millimeter wave massive MIMO full duplex with limited dynamic range,” IEEE Open J. Commun. Soc., vol. 3, pp. 127–143, 2022.arxiv.org/abs/2104.11537
  23. [23]F. Liu, C. Masouros, A. Li, T. Ratnarajah, and J. Zhou, “MIMO radar and cellular coexistence: A power-efficient approach enabled by interference exploitation,” IEEE Trans. Signal Process., vol. 66, no. 14, pp. 3681–3695, 2018.DOI
  24. [24]F. Liu, L. Zhou, C. Masouros, A. Li, W. Luo, and A. Petropulu, “Toward dual-functional radar-communication systems: Optimal waveform design,” IEEE Trans. Signal Process., vol. 66, no. 16, pp. 4264–4279, 2018.DOI
  25. [25]C. G. Tsinos, A. Arora, S. Chatzinotas, and B. Ottersten, “Joint transmit waveform and receive filter design for dual-function radar-communication systems,” IEEE J. Sel. Topics Signal Process., vol. 15, no. 6, pp. 1378–1392, 2021.DOI
  26. [26]A. Hassanien, M. G. Amin, Y. D. Zhang, and F. Ahmad, “Signaling strategies for dual-function radar communications: An overview,” IEEE Aerosp. Electron. Syst. Mag., vol. 31, no. 10, pp. 36–45, 2016.DOI
  27. [27]P. Stoica, J. Li, and Y. Xie, “On probing signal design for MIMO radar,” IEEE Trans. Signal Process., vol. 55, no. 8, pp. 4151–4161, 2007.
  28. [28]J. Li and P. Stoica, “MIMO radar with colocated antennas,” IEEE Signal Process. Mag., vol. 24, no. 5, pp. 106–114, 2007.DOI
  29. [29]E. Lagunas, T. Ramírez-Parrado, J. A. Vásquez-Peralvo, J. L. González Ríos, P. Losada-Sanisdro, C. Mosquera, R. López-Valcarce, P. N. Vummadisetti, and S. Chatzinotas, “Full-duplex techniques for satellite communications: Feasibility analysis and roadmap,” IEEE Open J. Commun. Soc., vol. 6, pp. 2130–2151, 2025.DOI
  30. [30]L. You, K.-X. Li, J. Wang, X. Gao, X.-G. Xia, and B. Ottersten, “Massive MIMO transmission for LEO satellite communications,” IEEE J. Sel. Areas Commun., vol. 38, no. 8, pp. 1851–1865, 2020.DOI
  31. [31]K. Shen and W. Yu, “Fractional programming for communication systems—Part I: Power control and beamforming,” IEEE Trans. Signal Process., vol. 66, no. 10, pp. 2616–2630, 2018.DOI
  32. [32]——, “Fractional programming for communication systems—Part II: Uplink scheduling via matching,” IEEE Trans. Signal Process., vol. 66, no. 10, pp. 2631–2644, 2018.DOI
  33. [33]M. Razaviyayn, M. Hong, and Z.-Q. Luo, “A unified convergence analysis of block successive minimization methods for nonsmooth optimization,” SIAM J. Optim., vol. 23, no. 2, pp. 1126–1153, 2013.arxiv.org/abs/1209.2385
  34. [34]D. P. Bertsekas, Nonlinear Programming, 2nd ed. Belmont, MA, USA: Athena Scientific, 1999.

Paper details

vlnc:W_2g2jqr9d
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Engineering

Not recorded for this paper

View statement
Looking for related papers…
Contents