betaFeedback

WorksPhysics and Astronomy

Hybrid RIS-Enhanced ISAC Secure Systems: Joint Optimization in the Presence of an Extended Target

Abstract

Unlike the conventional fully-passive and fully-active reconfigurable intelligent surfaces (RISs), a hybrid RIS consisting of active and passive reflection units has recently been concerned, which can exploit their integrated advantages to alleviate the RIS-induced path loss. In this paper, we investigate a novel security strategy where the multiple hybrid RIS-aided integrated sensing and communication (ISAC) system communicates with downlink users and senses an extended target synchronously. Assuming imperfectly known target location (TL), we consider the joint design of the transmit signal and receive filter bank of the base station (BS), the receive beamformers of all users and the weights of the hybrid RIS. An optimization problem is formulated for maximizing the worst-case sensing signal-to-interference-plus-noise-ratio (SINR) subject to secure communication and system power budget constraints. To address this non-convex problem, we leverage generalized fractional programming (GFP) and penalty-dual-decomposition (PDD), and propose a security solution that efficiently optimizes all variables by employing convex optimization approaches. Simulation results show that by incorporating the multiple hybrid RIS into the optimization design, the extended target detection and secure transmission performance of ISAC systems are improved over the state-of-the-art RIS-aided ISAC approaches.

Introduction

The forthcoming sixth-generation (6G) wireless systems will enable many promising applications for instance vehicle-to-everything (V2X), smart cities and extended reality (XR) [1]. Therefore, there is a critical need to integrate environment sensing functionality into communication systems to yield perceptive wireless networks through the concept of integrated sensing and communications (ISAC) [2]. However, ISAC systems are confronted with serious security problems owing to not only the broadcasting nature of wireless transmissions but also the fact that the detected target might possibly eavesdrop the confidential information-bearing signal sent to the licensed receivers within range, which poses a new security concern [3, 4, 5, 6].

To overcome the potential security problem in ISAC networks, [7], sensing-centric ISAC systems were devised to convey a mixture of two different waveforms, containing communication information for the authorized receivers and artificial noise (AN) to disturb the Eve, both of which can be employed for radar target detection. However, the extra AN would unavoidably induce interference and deteriorate the network performance. Furthermore, communication-centric ISAC systems face severe security threats, since transmit waveforms, enabled for target detection, are usually vulnerable to wiretapping attacks owing to the reuse of a data embedding waveform [8, 9]. An optimization problem was formulated to maximize the radar received signal-to-interference-plus-noise ratio (SINR) with a particular secrecy rate requirement [10]. Different from the secrecy rate based approaches, the directional modulation (DM) scheme adjusts the amplitude and phase of the symbols at the desired receivers while disturbing the symbols in unintended directions, which means that the modulation occurs at the antenna level instead of at the baseband level. The DM-based technique is based on the principles of utilizing constructive interference (CI) [11, 12], where the received waveform is not required to be aligned with the desired symbols, but is kept away from the detection threshold levels of the constellation. The symbol-level precoding scheme, which exploits more available degrees of freedom (DoFs) in both the spatial and temporal domains, can offer enhanced transmit beampatterns to realize superior sensing performance, as well as convert harmful multiuser interference (MUI) into CI for enhancing multi-user communication quality [8]. However, adding sensing functionality to communication network degrades the communication quality since the two objectives might conflict with each other.

Reconfigurable intelligent surfaces (RISs) are capable of adjusting channels to perform secure and reliable communications through designed waveform reflection which can be viewed as a promising technique for future 6G networks [13, 14]. Inspired by the huge potential provided by a RIS, various works have been devoted to the optimization of RIS-enabled ISAC systems [15]–[18]. Since passive RIS units only adjust the signal phase, the fully passive RIS enhanced channel suffers serious propagation attenuation, particularly when the RIS doesn’t consist of a large number of reflection units. The fully active RIS is capable of utilizing amplifiers to tackle the serious channel attenuation. However, it requires extra power consumption to improve the strength of the reflected waveforms and noise at the active RIS [19]. To overcome the issue, a hybrid RIS including a certain number of active units was proposed [20, 21], which serves two purposes of amplifying and reflecting incident signals and achieves a significant ISAC performance improvement. A hybrid RIS can be considered as a promising framework to reduce the influences on system performance improvement that occur owing to severe transmission attenuation. The robust beamforming optimization for a hybrid RIS-enabled ISAC system was proposed in [20]. The work of [21] developed a design scheme to optimize the data rate for a hybrid RIS-assisted communication network that can operate in time-varying Rician fading channels. The influence of the mode switching of active-passive reflection elements on the mobile edge computing-aided system was investigated in [22]. A beamforming optimization method was proposed in the multi-RIS aided communication system, where the weights of multi-RIS and transmit beamforming are cooperatively designed to enhance the system performance [23]. Also, a similar problem was considered for multiple hybrid RIS-aided systems, which design the transmit beamforming at the base station (BS) and the reflect beamforming at the RIS to improve robustness against blockages [24].

The incorporation of a RIS into the DM technique has been revealed to be valuable for security communications [25, 26, 27]. To minimize the energy consumption in DM, a RIS-assisted secure DM approach is proposed in [25], where a design problem is established to maximize the secrecy throughput by designing the hybrid precoding and the RIS beamforming. The authors of [27] considered a joint design problem that optimizes the transmit waveform of ISAC and the weights of the RIS. With the DM-based scheme, the transmit waveform is optimized to fall into the constructive area of potential Eves. However, the accurate prior information of extended radar target (the target aspect angle and location) is generally unknown since the angle estimation of extended radar target includes a degree of uncertainty [23, 28]. The authors of [29] considered robust transceiver design for a secure ISAC system, and proposed robust optimization scheme with imperfect sensing channel state information (CSI). To the best of our knowledge, the DM-based secure scheme for multi-antenna communication users in a hybrid RIS-aided ISAC system under imperfect CSI has not been studied before.

Motivated by the aforementioned observations, this work proposes a secure optimization framework for hybrid RIS-aided ISAC systems, with a particular emphasis on the maximization of worst-case SINR for extended target detection under imperfect CSI. Specifically, considering that the radar target might intercept the confidential information intended to the secure communication users (SCUs), the DM-based method is first adopted for securing multiple hybrid RIS-aided ISAC. The comparison between this scheme and other relevant works is provided in Table I and the primary contributions of our work are listed as follows:

  • We propose a novel multiple hybrid RIS-aided ISAC system which serves multiple-antenna SCUs and detects a single-antenna Eve simultaneously. The system model is extended to a general scenario where the target location (TL) is uncertain to the BS. As a consideration on secure transmission, the MUI is devised to be constructive to SCUs, while destructive to the Eve.

  • To maximize the worst-case sensing SINR among all possible TLs, we jointly design the transmit signal and receive filters at the BS, the receive beamformers at each SCU, together with the weights at the hybrid RIS, while guaranteeing the CI-type communication QoS and DI-type security requirements, the RIS weight constraint, and total power budget constraint.

  • We utilize a sequential optimization framework based on generalized fractional programming (GFP) to handle the coupling problem of all variables. Particularly, to solve the challenging hybrid RIS configuration problem, we appropriately split variables and leverage the penalty dual decomposition (PDD) technique combined with the penalty convex-concave procedure (PCCP) method. We find an optimized solution to resolve the quartic optimization by tackling several quadratic sub-problems.

  • Numerical results indicate that the developed design scheme can realize better performance than the state-of-the-art benchmark methods. Moreover, the potential of a multiple hybrid RIS for enhancing the ISAC performance is confirmed and the capability enhancement enlarges with the increasing total power consumption of the system and number of hybrid RIS reflection units.

The remainder of this paper is organized as follows: Section II introduces the hybrid RIS-enhanced ISAC secure system model and the formulation of the joint design problem. Section III develops the efficient solution technique for the employed performance metric. In Section IV, simulation results are given, whereas in Section V, the conclusions are provided.

Notations: Matrices are denoted by bold uppercase letters and vectors are denoted by bold lowercase letters. The trace and the vectorization operations are represented by tr⁡(⋅)\operatorname{tr}(\cdot) and vec⁡(⋅)\operatorname{vec}(\cdot), respectively. (⋅)T(\cdot)^{T}, (⋅)H(\cdot)^{H} and (⋅)∗(\cdot)^{*} signify transpose, Hermitian transpose and complex conjugate of matrices, respectively. ⊗\otimes and ⊙\odot are the Kronecker product and Hadamard product, respectively. The magnitude of scalar aa, the norm of vector a\mathbf{a} and the Frobenius norm of matrix A\mathbf{A} are signified by ∣a∣|a|, ∥a∥\|\mathbf{a}\|, and ∥A∥F\|\mathbf{A}\|_{F}, respectively. en\mathbf{e}_{n} is the nnth column of the identity matrix IN\mathbf{I}_{N}. E(⋅)\mathbb{E}(\cdot) indicates the statistical expectation operation.

System model

We consider multiple hybrid RIS-aided ISAC system as described in Figure 1, where a BS communicates with KK multi-antenna SCUs and detects an extended target with the help of multiple hybrid RIS concurrently. The BS is equipped with NaN_{a} (Na≥KN_{a} \ge K) transmit/receive antennas. The extended target is viewed as a single-antenna Eve which may wiretap the private message transmitted from the BS to each SCU. Specifically, the BS firstly transmits the confidential signals to each SCU while radiating the Eve. Then, the BS observes the scattering behavior of the extended target using the return signals reflected from the target. Since employing traditional communication waveforms to sense a radar target needs minor modifications to developed transmission networks and does not generate additional self-interference, according to [16, 30], we adopt communication waveforms to perform ISAC operation. The hybrid RIS is equipped with NIN_I units, containing AA active and NI−AN_I-A passive reflecting units. We now introduce notations to mathematically model the multiple hybrid RIS. Specifically, let Q\mathbb{Q} be the index set of the AA active units, Q∈{1,…,A}\mathbb{Q}\in\{1,\ldots,A\}, and let ϑs,n\vartheta_{s,n} be the reflection coefficient of the nnth unit of the ssth RIS, which is expressed as

Image not extracted

Figure 1. A description of the studied hybrid RIS-enhanced ISAC secure system.

Related worksISACDMExtended TargetImperfect CSIHybrid RISMultiple RIS
[20]✓✓
[23]✓✓
[25]✓
[27]✓✓
[28]✓✓
[29]✓✓
This work✓✓✓✓✓✓

Table 1. Contributions in contrast to the state-of-the-art.

ϑs,n={∣as,n∣ejμs,n,n∈Q,ejμs,n,n∉Q,(1)\vartheta_{s,n} = \begin{cases} |a_{s,n}|e^{j\mu_{s,n}}, & n\in\mathbb{Q},\\ e^{j\mu_{s,n}}, & n\notin\mathbb{Q}, \end{cases} \tag*{(1)}

where as,na_{s,n} denotes the amplitude of the signal generated by the active unit, and μs,n∈[0,2π)\mu_{s,n}\in[0,2\pi) is the phase of the signal. Let Θs=diag⁡{ϑs,1,⋯ ,ϑs,NI}∈CNI×NI\boldsymbol{\Theta}_s=\operatorname{diag}\{\vartheta_{s,1},\cdots,\vartheta_{s,N_I}\}\in\mathbb{C}^{N_I\times N_I} be the reflection coefficient matrix of the ssth hybrid RIS. We define an additive decomposition for it as Θs=Ψs+Φs\boldsymbol{\Theta}_s=\boldsymbol{\Psi}_s+\boldsymbol{\Phi}_s, where Ψs=INIQ∘Θs=diag⁡{φs,1,⋯ ,φs,NI}\boldsymbol{\Psi}_s=\mathbf{I}_{N_I}^{\mathbb{Q}}\circ\boldsymbol{\Theta}_s=\operatorname{diag}\{\varphi_{s,1},\cdots,\varphi_{s,N_I}\} and Φs=(INI−INIQ)∘Θs=diag⁡{ϕs,1,⋯ ,ϕs,NI}\boldsymbol{\Phi}_s=(\mathbf{I}_{N_I}-\mathbf{I}_{N_I}^{\mathbb{Q}})\circ\boldsymbol{\Theta}_s=\operatorname{diag}\{\phi_{s,1},\cdots,\phi_{s,N_I}\} contain the active and passive RIS coefficients, respectively. where INIQ\mathbf{I}_{N_I}^{\mathbb{Q}} is an NI×NIN_I\times N_I diagonal matrix whose non-zero elements are all unity and have positions determined by Q\mathbb{Q}. The discrete RIS possesses bb-bit controllability, where each individual reflector of the RIS is encoded by the controller to enable 2b2^b distinct phase shift modes μs,n=2πn2b\mu_{s,n}=\frac{2\pi n}{2^b}, n∈{0,1,…,2b−1}n\in\{0,1,\ldots,2^b-1\}, n∈NIn\in N_I. We assume BS and RIS adopt uniform planner arrays (UPA) to support secure ISAC scheme.

Multiuser Communications Model

For UPA with Na=Lx,B×Lz,BN_a=L_{x,B}\times L_{z,B} and NI=Lx,s×Lz,sN_I=L_{x,s}\times L_{z,s} antennas, the channel gain from the BS to the ssth RIS Gs∈CNI×Na\mathbf{G}_s\in\mathbb{C}^{N_I\times N_a} is modeled as

Gs=λB,s1+λB,sHB,sLoS+11+λB,sHB,sNLoS,(2)\mathbf{G}_s= \sqrt{\frac{\lambda_{B,s}}{1+\lambda_{B,s}}}\mathbf{H}_{B,s}^{\mathrm{LoS}}+ \sqrt{\frac{1}{1+\lambda_{B,s}}}\mathbf{H}_{B,s}^{\mathrm{NLoS}}, \tag*{(2)}

where λB,s\lambda_{B,s} is the Rician factor of the ssth BS-RIS link. The line-of-sight (LoS) component HB,sLoS∈CNI×Na\mathbf{H}_{B,s}^{\mathrm{LoS}}\in\mathbb{C}^{N_I\times N_a} and scattering component HB,sNLoS∈CNI×Na\mathbf{H}_{B,s}^{\mathrm{NLoS}}\in\mathbb{C}^{N_I\times N_a} are respectively expressed as HB,sLoS=ar(θs,φs)atT(θB,φB)\mathbf{H}_{B,s}^{\mathrm{LoS}}=\mathbf{a}_r(\theta_s,\varphi_s)\mathbf{a}_t^{T}(\theta_B,\varphi_B) and HB,sNLoS=∑l=1LB,scB,slar(θsl,φsl)atT(θBl,φBl)\mathbf{H}_{B,s}^{\mathrm{NLoS}}=\sum_{l=1}^{L_{B,s}}c_{B,s}^{l}\mathbf{a}_r(\theta_s^l,\varphi_s^l)\mathbf{a}_t^{T}(\theta_B^l,\varphi_B^l), where

at(θB,φB)=1Na[1,…,ej2πd(ix,Bcos⁡φBcos⁡θB+iz,Bsin⁡θB),…,ej2πd((Lx,B−1)cos⁡φBcos⁡θB+(Lz,B−1)sin⁡θB)]T,(3)\mathbf{a}_t(\theta_B,\varphi_B)=\frac{1}{\sqrt{N_a}}[1,\ldots,e^{j\frac{2\pi}{d}(i_{x,B}\cos\varphi_B\cos\theta_B+i_{z,B}\sin\theta_B)},\ldots,e^{j\frac{2\pi}{d}((L_{x,B}-1)\cos\varphi_B\cos\theta_B+(L_{z,B}-1)\sin\theta_B)}]^T, \tag*{(3)}

References

  1. [1]A. Zhang, M. L. Rahman, X. Huang, Y. J. Guo, and R. W. Heath, “Perceptive mobile network: Cellular networks with radio vision via joint communication and radar sensing,” IEEE Veh. Technol. Mag., vol. 16, no. 2, pp. 20–30, 2021.DOI
  2. [2]F. Liu, Y. Cui, C. Masouros, J. Xu, T. X. Han, Y. C. Eldar, and S. Buzzi, “Integrated sensing and communications: Towards dual-functional wireless networks for 6G and beyond,” IEEE J. Sel. Areas Commun., vol. 40, no. 6, pp. 1728–1767, 2022.arxiv.org/abs/2108.07165
  3. [3]S. Fang, G. Chen, P. Xiao, K.-K. Wong, and R. Tafazolli, “Intelligent omni surface-assisted self-interference cancellation for full-duplex MISO system,” IEEE Trans. Wireless Commun., vol. 23, no. 3, pp. 2268–2281, 2024.arxiv.org/abs/2208.06457
  4. [4]Y. Wen, G. Chen, S. Fang, Z. Chu, P. Xiao, and R. Tafazolli, “STAR-RIS-assisted-duplex jamming design for secure wireless communications system,” IEEE Trans. Inf. Forensics Security, pp. 1–1, 2024.arxiv.org/abs/2309.04566
  5. [5]H. Jia, X. Li, and L. Ma, “Physical layer security optimization with Cramer-Rao bound metric in ISAC systems under sensing-specific imperfect CSI model,” IEEE Trans. Veh. Technol., pp. 1–13, 2023.DOI
  6. [6]Z. Ren, L. Qiu, J. Xu, and D. W. K. Ng, “Robust transmit beamforming for secure integrated sensing and communication,” IEEE Trans. Commun., vol. 71, no. 9, pp. 5549–5564, 2023.arxiv.org/abs/2207.13863
  7. [7]A. Deligiannis, A. Daniyan, S. Lambotharan, and J. A. Chambers, “Secrecy rate optimizations for MIMO communication radar,” IEEE Trans. Aerosp. Electron. Syst., vol. 54, no. 5, pp. 2481–2492, 2018.DOI
  8. [8]N. Su, F. Liu, Z. Wei, Y. F. Liu, and C. Masouros, “Secure dual-functional radar-communication transmission: Exploiting interference for resilience against target eavesdropping,” IEEE Trans. Wireless Commun., vol. 18, no. 6, pp. 1728–1767, 2023.arxiv.org/abs/2107.04747
  9. [9]H. Xu, T. Yang, K.-K. Wong, and G. Caire, “Achievable regions and precoder designs for the multiple access wiretap channels with confidential and open messages,” IEEE J. Sel. Areas Commun., vol. 40, no. 5, pp. 1407–1427, 2022.arxiv.org/abs/2107.14163
  10. [10]B. K. Chalise, M. G. Amin, and B. Himed, “Performance tradeoff in a unified passive radar and communications system,” IEEE Signal Process. Lett., vol. 24, no. 9, pp. 1275–1279, 2017.DOI
  11. [11]F. Liu, C. Masouros, A. L. T. Ratnarajah, and J. Zhou, “MIMO radar and cellular coexistence: A power-efficient approach enabled by interference exploitation,” IEEE Trans. Signal Process., vol. 66, no. 14, pp. 3681–3695, 2018.arxiv.org/abs/1704.08920
  12. [12]M. R. A. Khandaker, C. Masouros, K.-K. Wong, and S. Timotheou, “Secure SWIPT by exploiting constructive interference and artificial noise,” IEEE Trans. Wireless Commun., vol. 67, no. 2, pp. 1326–1340, 2019.DOI
  13. [13]Q. Wu, S. Zhang, B. Zheng, C. You, and R. Zhang, “Intelligent reflecting surface-aided wireless communications: A tutorial,” IEEE Trans. Wireless Commun., vol. 69, no. 5, pp. 3313–3351, 2021.arxiv.org/abs/2007.02759
  14. [14]C. Wang, Z. Li, T.-X. Zheng, D. W. K. Ng, and N. Al-Dhahir, “Intelligent reflecting surface-aided secure broadcasting in millimeter wave symbiotic radio networks,” IEEE Trans. Veh. Technol., vol. 70, no. 10, pp. 11050–11055, 2021.DOI
  15. [15]M. Hua, Q. Wu, W. Chen, O. A. Dobre, and A. Lee Swindlehurst, “Secure intelligent reflecting surface aided integrated sensing and communication,” IEEE Trans. Wireless Commun., pp. 1–1, 2023.arxiv.org/abs/2207.09095
  16. [16]R. Liu, M. Li, Y. Liu, Q. Wu, and Q. Liu, “Joint transmit waveform and passive beamforming design for RIS-aided DFRC systems,” IEEE J. Sel. Topics Signal Process., vol. 16, no. 5, pp. 995–1010, 2022.DOI
  17. [19]Z. Yu, H. Ren, C. Pan, G. Zhou, B. Wang, M. Dong, and J. Wang, “Active RIS-aided ISAC systems: Beamforming design and performance analysis,” IEEE Trans. Commun., vol. 72, no. 3, pp. 1578–1595, 2024.arxiv.org/abs/2302.08934
  18. [20]C. Liao, F. Wang, G. Han, Y. Huang, and V. K. N. Lau, “Beamforming design for hybrid active-passive RIS assisted integrated sensing and communications,” IEEE Commun. Lett., vol. 27, no. 11, pp. 2938–2942, 2023.DOI
  19. [21]D. V. Q. Rodrigues and T. Singh, “Efficient power allocation strategies in hybrid active-passive reconfigurable intelligent surfaces,” IEEE Commun. Lett., vol. 28, no. 1, pp. 113–117, 2024.DOI
  20. [22]H. Xie, D. Li, and B. Gu, “Exploring hybrid active-passive RIS-aided MEC systems: From the mode-switching perspective,” IEEE Trans. Wireless Commun., pp. 1–1, 2024.arxiv.org/abs/2212.08298
  21. [23]Z. Chen, J. Tang, X. Y. Zhang, Q. Wu, G. Chen, and K.-K. Wong, “Robust hybrid beamforming design for Multi-RIS assisted MIMO system with imperfect CSI,” IEEE Trans. Wireless Commun., vol. 22, no. 6, pp. 3913–3926, 2023.DOI
  22. [24]P. Wang, J. Fang, X. Yuan, Z. Chen, and H. Li, “Intelligent reflecting surface-assisted millimeter wave communications: Joint active and passive precoding design,” IEEE Trans. Veh. Technol., vol. 69, no. 12, pp. 14960–14973, 2020.
  23. [25]F. Shu, L. Yang, X. Jiang, W. Cai, W. Shi, M. Huang, J. Wang, and X. You, “Beamforming and transmit power design for intelligent reconfigurable surface-aided secure spatial modulation,” IEEE J. Sel. Topics Signal Process., vol. 16, no. 5, pp. 933–949, 2022.DOI
  24. [26]F. Shu, Y. Teng, J. Li, M. Huang, W. Shi, J. Li, Y. Wu, and J. Wang, “Enhanced secrecy rate maximization for directional modulation networks via IRS,” IEEE Trans. Commun., vol. 69, no. 12, pp. 8388–8401, 2021.arxiv.org/abs/2008.05067
  25. [27]C. Wang, C.-C. Wang, Z. Li, D. W. K. Ng, K.-K. Wong, N. Aldhahir, and D. Niyato, “STAR-RIS-enabled secure dual-functional radar-communications: Joint waveform and reflective beamforming optimization,” IEEE Trans. Inf. Forensics Security, vol. 18, pp. 4577–4592, 2023.
  26. [28]Y. Wang, M. Tao, and S. Sun, “Cramer-Rao bound analysis and beamforming design for integrated sensing and communication with extended targets,” IEEE Trans. Wireless Commun., vol. 23, no. 11, pp. 15987–16000, 2024.arxiv.org/abs/2406.01937
  27. [29]Y. Zhang, W. Ni, J. Wang, W. Tang, M. Jia, Y. C. Eldar, and D. Niyato, “Robust transceiver design for covert integrated sensing and communications with imperfect CSI,” IEEE Trans. Commun., pp. 1–1, 2024.DOI
  28. [30]L. Chen, Z. Wang, Y. Du, Y. Chen, and F. R. Yu, “Generalized transceiver beamforming for DFRC with MIMO radar and MU-MIMO communication,” IEEE J. Sel. Areas Commun., vol. 40, no. 6, pp. 1795–1808, 2022.DOI
  29. [31]C. Masouros and G. Zheng, “Exploiting known interference as green signal power for downlink beamforming optimization,” IEEE Trans. Signal Process., vol. 63, no. 14, pp. 3628–3640, 2015.DOI
  30. [32]L. Shi, P. Wang, H. Liu, L. Xu, and Z. Bao, “Radar HRP statistical recognition with local factor analysis by automatic Bayesian ying-yang harmony learning,” IEEE Trans. Signal Process., vol. 59, no. 2, pp. 610–617, 2011.
  31. [33]N. T. Nguyen, V.-D. Nguyen, H. V. Nguyen, H. Q. Ngo, S. Chatzinotas, and M. Juntti, “Spectral efficiency analysis of hybrid relay-reflecting intelligent surface-assisted cell-free massive MIMO systems,” IEEE Trans. Wireless Commun., vol. 22, no. 5, pp. 3397–3416, 2023.DOI
  32. [34]D. Maio, Antonio, Kurbasi, S. Mohammad, Aubry, Augusto, Bastani, and M. Hasan, “Robust transmit code and receive filter design for extended targets in clutter,” IEEE Trans. Signal Process., vol. 63, no. 8, pp. 1965–1976, 2015.
  33. [35]Y. Cheng, M. Pesavento, and A. Philipp, “Joint network optimization and downlink beamforming for CoMP transmissions using mixed integer conic programming,” IEEE Trans. Signal Process., vol. 61, no. 16, pp. 3972–3987, 2013.DOI
  34. [36]Q. Shi and M. Hong, “Penalty dual decomposition method for non-smooth nonconvex optimization-part I: Algorithms and convergence analysis,” IEEE Trans. Signal Process., vol. 68, pp. 4108–4122, 2020.
  35. [37]T. Lipp and S. Boyd, “Variations and extension of the convex-concave procedure,” Optim. Eng., vol. 17, no. 2, pp. 263–287, 2016.DOI
  36. [38]L. Du, Q. Liang, Z. Ma, and P. Fan, “Over-the-air interference suppression using reconfigurable intelligent surface with discrete reflection coefficients (DRC) design,” IEEE Trans. Veh. Technol., vol. 73, no. 5, pp. 7310–7315, 2024.DOI
  37. [39]L. Du, P. Fan, Z. Ma, and Q. Liang, “RIS assisted radar-communication coexistence system with discrete reflection coefficients,” IEEE Trans. Wireless Commun., vol. 24, no. 4, pp. 3014–3028, 2025.DOI

Paper details

vlnc:W_2mddt92r
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents