betaFeedback

WorksPhysics and Astronomy

Theoretical and Experimental Investigations of High-Performance Sr2CoNbO6-delta Double Perovskite for IT-SOFC Cathode Applications

Abstract

Enhancing the transport of oxygen anions in the cathode while maintaining surface stability is essential for improving the performance of intermediate-temperature solid oxide fuel cells (IT-SOFCs). This study investigates a novel cathode material candidate, Sr2CoNbO6-delta (SCNO), using density functional theory, molecular dynamics, and experimental characterization. The redox active Co cation at B-site and less reducible Nb cation at the B'-site together enhance both surface stability and electrocatalytic performance. SCNO is observed to have a higher concentration of oxygen vacancies and increased oxygen diffusivity on the surface. The surface stability of SCNO is further improved when simulated under compressive strain due to the GDC electrolyte substrate. These findings offer new insights into controlling Sr segregation in SCNO, contributing to a better understanding of its enhanced oxygen reduction reaction (ORR) activity and high surface stability. Subsequently, SCNO was synthesized to evaluate its potential as a cathode material in SOFCs. To assess its performance, symmetric cells with uniform dense thin films of varying thicknesses (40 and 80 nm) were fabricated using the pulsed laser deposition technique. Electrochemical impedance spectroscopy and distributed relaxation time analysis indicate that bulk oxygen ion diffusion is a limiting factor for the ORR in SCNO. The polarization resistance for the 40 and 80 nm dense thin film symmetric cells ranged between 0.329 - 0.241 ohm cm2 and 1.095 - 0.438 ohm cm2, respectively, within the temperature range of 773 - 973 K in an air atmosphere. The full cell configuration of NiO-GDC|GDC|SCNO demonstrated a significantly high peak power density of 0.633 W/cm2 at 973 K. This theory-guided design and experimental study suggest that SCNO is a promising candidate for IT-SOFC cathode materials.

Introduction

Solid oxide fuel cells are highly efficient and versatile energy conversion devices that convert chemical energy into electricity[1]. SOFCs operate at high temperatures (1073-1273 K). The cathode material in SOFCs plays a vital role in ORR for oxygen incorporation and transport[2, 3]. The high operating temperature condition supports good ORR activity but necessitates the use of stable and costly materials for SOFC cathodes. Lowering the operating temperature results in sluggish ORR activity, limiting the overall performance of SOFCs. To overcome this challenge and improve the efficiency of SOFCs, developing novel cathode materials with enhanced ORR activity and oxygen ion diffusion at the intermediate temperature range (< 1073 K) is essential. As a result, significant research efforts have been devoted to exploring novel IT-SOFC cathode materials to reduce their cost and increase stability[4, 5]. In recent years, extensive research has focused on double perovskite structures, specifically A2BB′O6−δA_2BB'\mathrm{O}_{6-\delta} (B/B' = 3d, 4d, and 5d transition metals), to address the need for highly efficient cathodes that can transport oxygen ions effectively[6, 7]. Sr2BB′O6−δ\mathrm{Sr}_2BB'\mathrm{O}_{6-\delta}, type of double perovskite oxide materials have been widely studied for electronic and magnetic properties for various applications[8, 9, 10, 11]. The high structural stability and magnetic ordering of Sr2BB′O6−δ\mathrm{Sr}_2BB'\mathrm{O}_{6-\delta} are leading research interests to probe their applicability to various applications. Researchers have reported Sr2BB′O6−δ\mathrm{Sr}_2\mathrm{B}\mathrm{B}'\mathrm{O}_{6-\delta}-type double perovskites as potential candidates for electrode applications in SOFCs. Some double perovskite oxides developed as electrode materials for SOFCs are Sr2MgMoO6−δ\mathrm{Sr}_2\mathrm{MgMoO}_{6-\delta}[12], Sr2Fe2O6−δ\mathrm{Sr}_2\mathrm{Fe}_2\mathrm{O}_{6-\delta}[13, 14], and Sr2Fe1.5Mo0.5O6−δ\mathrm{Sr}_2\mathrm{Fe}_{1.5}\mathrm{Mo}_{0.5}\mathrm{O}_{6-\delta}[15]. Tian et al. reported that co-doped Sr2FeNbO6−δ\mathrm{Sr}_2\mathrm{FeNbO}_{6-\delta} is a chemically compatible cathode material with high conductivity and low polarization resistance for IT-SOFCs[16]. Sr2MgMoO6\mathrm{Sr}_2\mathrm{MgMoO}_6 and Sr2MnMoO6\mathrm{Sr}_2\mathrm{MnMoO}_6 are reported to show high-performance power density of 838 mW/cm2^2 and 658 mW/cm2^2 at 1073 K, respectively, for anode applications[12]. Sr2CoNbO6−δ\mathrm{Sr}_2\mathrm{CoNbO}_{6-\delta} is reported to show non-stoichiometry of oxygen, which is crucial for cathodic applications[17, 18, 19]. In addition, Nb5+\mathrm{Nb}^{5+} doping at B-site of SrCoO3−δ\mathrm{SrCoO}_{3-\delta} is also reported to show a lower area-specific resistance (ASR) of 0.16 and 0.68 Ω\Omega/cm2^2 at 773 and 723 K, respectively[20].

Structures incorporating strontium (Sr) at the A-site, exhibit good electrical conductivity, enhancement of oxygen defects, and performance of fuel cell[21, 22]. However, it has been noted that the Sr at A-site tends to segregate from the bulk and accumulate on the surface, forming insulating phases (SrO)[23]. This can have a detrimental effect on the electrochemical performance as it tends to reduce the oxygen incorporation and oxygen diffusion on the surface by blocking the way for incoming oxygen molecules[23]. For example, Sr cation segregation in perovskites cathodes, such as La1−xSrxMnO3−δ\mathrm{La}_{1-x}\mathrm{Sr}_x\mathrm{MnO}_{3-\delta} (LSM)[24, 25], La1−xSrxCo1−yFeyO3−δ\mathrm{La}_{1-x}\mathrm{Sr}_x\mathrm{Co}_{1-y}\mathrm{Fe}_y\mathrm{O}_{3-\delta} (LSCF)[26], La1−xSrxCoO3−δ\mathrm{La}_{1-x}\mathrm{Sr}_x\mathrm{CoO}_{3-\delta} (LSC)[27] and LnBa1−xSrxCo2O6−δ\mathrm{LnBa}_{1-x}\mathrm{Sr}_x\mathrm{Co}_2\mathrm{O}_{6-\delta}[28, 29], is observed to affect the long-term stability and electrochemical performance of the cathode. Previous studies have shown that the extent of Sr segregation is affected by various factors, such as materials’ oxygen non-stoichiometry[30], composition[25, 28], temperature[25], operating condition[31], and lattice strain[28, 32]. For instance, Koo et al. have proposed various strategies to control Sr surface segregation, such as imparting strain by lowering pO2_2, isovalent substitution, non-stoichiometric compositions, and surface modification[33]. In addition, Tsvetkov et al.[34] and Ramírez et al.[9] explored doping with high oxidation state and less reducible cations, like Al3+\mathrm{Al}^{3+}, Nb5+\mathrm{Nb}^{5+}, Hf4+\mathrm{Hf}^{4+}, Ti4+\mathrm{Ti}^{4+}, Sb5+\mathrm{Sb}^{5+}, Mo6+\mathrm{Mo}^{6+}, or Zr4+\mathrm{Zr}^{4+}, to stabilize the perovskite structure, improve oxygen surface exchange kinetics, and prevent Sr surface segregation. Previous studies performed on La0.5Sr0.5CoO3−δ\mathrm{La}_{0.5}\mathrm{Sr}_{0.5}\mathrm{CoO}_{3-\delta} had also demonstrated that Nb doping enhances the oxygen ion diffusion coefficient[35]. These findings suggest that Sr2CoNbO6−δ\mathrm{Sr}_2\mathrm{CoNbO}_{6-\delta} as a material of interest for IT-SOFC cathodes. A deeper understanding of the oxygen reduction reaction (ORR) is necessary to further improve these materials. This knowledge could enhance electrocatalytic activity and reduce Sr cation segregation in SCNO.

Alongside composition, fabrication techniques significantly influence the performance of cathode materials. Conventional fabrication techniques like tape casting, screen printing, and dip coating often face challenges. These include difficulties in controlling film thickness, uniformity, and porosity[36]. In addition, the films prepared with these techniques result in low oxygen vacancy concentrations and challenges in creating thin, multilayer films[37]. This affects the performance of the fuel cells. Pulsed laser deposition (PLD) offers a promising alternative. It allows precise control over microstructure and composition while maintaining high uniformity and optimizing the triple-phase boundary[38]. PLD, on the other hand, enhances ionic conductivity by forming heterogeneous structures and improving SOFC performance[39]. For example, Choi et al. demonstrated this by using PLD to prepare PrBa0.5Sr0.5Co1.5Fe0.5O5+δ\mathrm{PrBa_{0.5}Sr_{0.5}Co_{1.5}Fe_{0.5}O_{5+\delta}} thin films (∼100\sim100 nm thick) on a BaZr0.4Ce0.4Y0.1Yb0.1O3\mathrm{BaZr_{0.4}Ce_{0.4}Y_{0.1}Yb_{0.1}O_{3}} electrolyte. The PLD-produced films achieved a peak power density of ∼1098 mW/cm2\sim1098\ \mathrm{mW}/\mathrm{cm}^{2}, significantly higher than the ∼800 mW/cm2\sim800\ \mathrm{mW}/\mathrm{cm}^{2} achieved by films made with conventional methods at 873 K[40]. This also reduced offset resistance by improving cathode-electrolyte contact[40]. Despite its advantages, only a few studies have focused on depositing thin films of double perovskite oxides using PLD for SOFCs.

In the present work, we have investigated SCNO, a double perovskite material, as a candidate for IT-SOFC cathode applications. We started with a theoretical study of electrocatalytic properties and surface stability. DFT and MD simulations showed that SCNO exhibits high surface stability, oxygen vacancy concentrations, and oxygen anion diffusion. Subsequently, SCNO was synthesized experimentally, and a comprehensive characterization was performed, including the analysis of phase composition, surface morphology, oxidation states, and electrochemical performance as a cathode in SOFCs. To investigate rate-limiting factors in the ORR activity, symmetric cells were fabricated with 40 nm and 80 nm thicknesses using PLD. The rate-limiting processes in these thin-film symmetric cells were examined using EIS and DRT analysis. By combining theoretical insights with experimental design, we explored the underlying factors contributing to the high surface stability and enhanced performance of SCNO and found it as a potential candidate for IT-SOFC cathodes.

Methodology

Theoretical simulations

Spin-polarized density functional theory simulations were performed using the plane-wave pseudopotential approach implemented in the Vienna Ab Initio Simulation Package (VASP-5.4.4)[41, 42]. We used the projector augmented wave method (PAW) to account core electronic states and the Perdew-Burke-Ernzerof functional (GGA-PBE) as the exchange-correlation potential[43, 44].

All simulations were performed with an energy cut-off of 520 eV. Hubbard correction was included to predict the accurate behavior of strongly localized dd-electrons in Co and Nb. The U values were obtained using the Cococcioni method[45]. The calculated U values for Co and Nb are 5.45 and 4.01 eV, respectively (Figure S1). The convergence criteria of 10−610^{-6} eV and 0.05 eV/Å were used for electronic and ionic relaxation, respectively. We used 3×3×33 \times3 \times3 and 3×3×13 \times3 \times1 gamma-centered k-mesh grids in computations for bulk and slabs, respectively.

To trace the dynamics of ions, molecular dynamics simulations were performed on Sr2CoNbO5.75\mathrm{Sr}_{2}\mathrm{CoNbO}_{5.75} using the Large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS, Sandia National Laboratories, USA)[46]. Buckingham inter-atomic potentials[47] were used to compute the interactions of cations with oxygen anion, with a cut-off radius of 20 Å. The coulombic and van der Waals interactions in the potential are expressed as

φ(rij)=zizje24πε0rij+Aije−rij/ρij−Cijrij6,\varphi(r_{ij}) = \frac{z_i z_j e^2}{4\pi\varepsilon_0 r_{ij}} + A_{ij}e^{-r_{ij}/\rho_{ij}} - \frac{C_{ij}}{r_{ij}^{6}},

where the parameters A, ρ, and C represent the strength of the Buckingham interaction. The parameters z and rijr_{ij} represent the ionic charge and interionic separation, respectively. The coulombic interactions were computed using particle-particle particle mesh with 10−410^{-4} eV/Å relative error in forces[48, 49]. The interaction parameters used in our MD simulations are provided in Table S1. We used the Nose-Hoover thermostat[50] and Verlet algorithm[51] to keep the temperature constant and integrate the equation of motion, respectively. To remove the finite size effects, we have used a larger supercell of 8×8×88 \times8 \times8 with 9,984 atoms. For surface properties, the slabs were terminated along the (001) direction with a 100 Å vacuum. For both bulk and surface simulations, the structure was equilibrated in NPT ensemble for 100 ps, then in NVT ensemble for 1 ns in the steps of 1 fs. The analysis was performed on 10 different MD runs using the same ensemble for 1 ns. The average of 10 production runs was considered while extracting the properties. Visual molecular dynamics program was employed to visualize the density profiles[49].

Experimental details

SCNO double perovskite was prepared using the combustion technique (citric acid- metal). A stoichiometric amount of Co(NO3)2⋅6H2O\mathrm{Co(NO_{3})_{2} \cdot6H_{2}O} (Alfa Aesar), Sr(NO3)2\mathrm{Sr(NO_{3})_{2}} (Alfa Aesar) and C4H4NNbO9⋅xH2O\mathrm{C_{4}H_{4}NNbO_{9} \cdot xH_{2}O} (Sigma Aldrich) was dissolved in 100 ml of deionized water. Then citric acid (Alfa Aesar) and polyethylene glycol (PEG-400, Alfa Aesar) were added to the above solution as a complexing agent under continuous stirring. The molar ratio of metal nitrate: PEG-400: citric acid was maintained as 1:1:1.5. The complex solution was stirred for 12 h at 363 K to evaporate water and gel formation. Further, the formed gel was self-combusted at 573 K to obtain a preliminary powder, followed by sintering at 1573 K for 48 h in the air to achieve the desired phase. The SCNO target was prepared by adding synthesized double perovskite in a one-inch-diameter dye set and pelletizing the powder using a hydraulic press at 200 kg/cm2\mathrm{kg/cm^{2}} pressure. Then, the obtained pellet was calcined at 1473 K for 6 h and polished using an emery paper to establish a close connection with the target holder. The gadolinium doped ceria (GDC, Fuel cell materials, USA) powder was mixed with a binder of 15% polyvinyl alcohol solution, followed by drying at 353 K overnight. The dry GDC was ground into a fine powder utilizing an automatic mortar pestle and pelletized in a dye set using a hydraulic press. The GDC pellets were heated at 1723 K for the duration of 10 h in a furnace under an air atmosphere and used further as an electrolyte to fabricate symmetric cells.

On GDC pellets, symmetric cells with thin film electrodes were developed using the PLD technique. We have optimized growth parameters, such as deposition temperature, target-to-substrate distance, post-deposition annealing temperature, oxygen partial pressure, oxygen pressure, laser fluence, and time, to accomplish the highest film quality. The thin film was formed under the following optimal conditions: Target-to-substrate distance was 5 cm, oxygen partial pressure was 10−310^{-3} mbar, and base pressure was maintained at 9×10−109 \times10^{-10} mbar. On the opposite side of the electrolyte, a similar deposition was made. After depositing, the pellet was annealed at 1473 K for an hour to acquire the stable electrode-electrolyte interface. Apart from this, SCNO was mixed with 10% PVA solution and dried in the oven at 353 K, followed by grinding into fine powder. For slurry preparation, the obtained SCNO powder was mixed with α\alpha-terpinol and ethyl cellulose, then pasted on a GDC pellet using a brush painting technique followed by calcination for 6 h at 1473 K.

An anode-supported single cell (NiO-GDC|GDC|SCNO-GDC) was fabricated by solid-state palletization of mixing 40 wt% nickel oxide (NiO, Alfa aesar), 59 wt% GDC, and pore former 1 wt% poly methyl methacrylate (PMMA, Alfa aesar) and added to the dye set. The GDC powder was layered on the NiO-GDC mixer, then palletized and sintered to 1723 K for 10 h. Similarly to NiO-GDC, the SCNO-GDC (SCNO 69% - GDC 30% and 1% PMMA) was prepared and coated on the obtained pellet (NiO-GDC|GDC) using brush painting, and then the cell fired at 1473 K for 6 h.

The as-synthesized SCNO double perovskite structure was analyzed using X-ray diffraction (XRD, Rigaku, MiniFlex 600). The structural information of as-synthesized SCNO was evaluated using FullProf software[54]. The morphological and microstructural analysis of SCNO powder, thin-film, and brush-painted cells were analyzed using the field-emission scanning electron microscopy technique (FESEM, TESCAN MIRA3, Czech Republic). The valence oxidation states of elements involved in the formation of double perovskite and its surface compositions were examined using X-ray photoelectron spectroscopy (XPS, Axis Supra).

The symmetric cells of 40 and 80 nm, and brush-painted cells EIS were carried out in the air to study the rate-limiting step of the oxygen reduction reaction. However, the challenge was associated with distinguishing various electrode processes because of their overlapping impedance contributions. Therefore, MATLAB code was used to effectively differentiate the complex electrode reaction mechanism to investigate EIS data using the DRT method[55]. In addition, an anode-supported full-cell, i.e., NiO-GDC|GDC|SCNO performance, was estimated in a split furnace temperature range of 773 - 973 K. The ambient air was utilized as an oxidant at the cathode side. Humidified 3 vol% of H₂O hydrogen was used as fuel on the anode side.

Results and Discussion

SCNO material was simulated using DFT simulations to probe electrocatalytic properties. The initial crystal structure information was taken from the prior experimental studies[19, 56, 57]. Using these experimental inputs, a unit cell of SCNO consisting of 20 atoms was constructed and subsequently optimized using DFT+U, to obtain a global minimum structure. Obtained lattice parameters, along with the available data from the literature for comparison, are provided in Table 1. As evident from the table, the computed lattice parameters are in good agreement with the literature values.

Materiala (Å)b (Å)c (Å)Ref.
Sr2CoNbO6{\mathrm{Sr}}_{2}{\mathrm{CoNbO}}_{6}5.565.567.87This Work
5.585.587.93[Ref. 56]
5.585.587.91[Ref. 19]
5.585.587.87[Ref. 57]
Sr2Co2O6{\mathrm{Sr}}_{2}{\mathrm{Co}}_{2}{\mathrm{O}}_{6}5.565.567.56This Work
Sr2Nb2O6{\mathrm{Sr}}_{2}{\mathrm{Nb}}_{2}{\mathrm{O}}_{6}5.755.758.20This Work

Table 1. Optimized lattice parameters for SCNO, SCO, and SNO from DFT simulations and literature.

The electrocatalytic properties of bulk SCNO are studied using DFT calculations with Hubbard correction to incorporate the effect of strongly correlated d-electrons of Co and Nb. Since oxygen vacancies play a major role in oxygen incorporation and transport, the oxygen vacancy formation energy (EOVE_{\mathrm{OV}}) could acts as a descriptor for the electrocatalytic performance of the material. Considering this, EOVE_{\mathrm{OV}} in possible oxygen vacancy sites is computed and analyzed in the SrO and CoNbO planes (Figure 1(a)). The EOVE_{\mathrm{OV}} was obtained using the expression

2 × 2 × 1 supercells of SCNO, SCO, and SNO structures

Figure 1. 2×2×12 \times2 \times1 supercells of (a) SCNO, (b) SCO, and (c) SNO structures with the oxygen vacancy site depicted as the black sphere in the (Co and/or Nb)O and SrO planes.

EOV=Edefect+0.5×EO2−Eperfect,E_{\mathrm{OV}} = E_{\mathrm{defect}} + 0.5 \times E_{\mathrm{O}_{2}} - E_{\mathrm{perfect}},

where EperfectE_{\mathrm{perfect}}, EdefectE_{\mathrm{defect}}, and EO2E_{\mathrm{O}_{2}} represent DFT energies associated with stoichiometric, non-stoichiometric structures, and gas-phase oxygen molecule, respectively.

Calculated values of EOVE_{\mathrm{OV}}’s are provided in Table 2. The EOVE_{\mathrm{OV}} in SrO and CoNbO planes are estimated to be 158.73 kJ/mol and 107.53 kJ/mol, respectively. This suggests oxygen vacancies formation to be more facilitated in the SrO plane than in the CoNbO plane. We anticipate the presence of Nb cations in the B′O plane to be responsible for the decreased favorability of oxygen vacancy creation. In order to investigate the effect of Nb on oxygen vacancy formation, system was remodeled with only Co or Nb cation at the B and B′-site, resulting in the formation of Sr2Co2O6\mathrm{Sr}_{2}\mathrm{Co}_{2}\mathrm{O}_{6} (SCO) and Sr2Nb2O6\mathrm{Sr}_{2}\mathrm{Nb}_{2}\mathrm{O}_{6} (SNO), respectively. SCO and SNO structures were subsequently fully optimized using DFT+U calculations. The lattice parameters for these systems are given in Table 1. The CoO plane of SCO (-41.74 kJ/mol for CoO and -37.33 for SrO plane) is observed to be the most favorable for oxygen vacancies, Figure 1(b). The study performed by Wexler et al. reported the impact of various transition metals at the B-site on EOVE_{\mathrm{OV}}[58]. The group also reported negative EOVE_{\mathrm{OV}}’s in SrCoO3SrCoO_{3}[58]. On the other hand, EOVE_{\mathrm{OV}} in NbO plane (220.05 kJ/mol for NbO and 194.69 for the SrO plane) of SNO is observed to be the highest among all the structures, Figure 1(c). The higher redox ability of Co than Nb could be a possible reason for the observed trend.

MaterialOxygen Vacancy PlaneEOVE_{\mathrm{OV}} (kJ/mol)
Sr2CoNbO6−δ\mathrm{Sr}_{2}\mathrm{CoNbO}_{6-\delta}CoNbO158.73
SrO107.53
Sr2Co2O6−δ\mathrm{Sr}_{2}\mathrm{Co}_{2}\mathrm{O}_{6-\delta}CoO-41.74
SrO-37.33
Sr2Nb2O6−δ\mathrm{Sr}_{2}\mathrm{Nb}_{2}\mathrm{O}_{6-\delta}NbO220.05
SrO194.69

Table 2. The oxygen vacancy formation energies (EOVE_{\mathrm{OV}}) for SCNO, SCO, and SNO structures in different crystal planes.

In order to probe the redox ability of ions in SCNO as the possible reason for the observed trend, the Bader charge analysis is performed on the perfect and oxygen-vacant structure of SCNO. Table 3 encapsulates the average Bader charges associated with Sr, Co, Nb, and O ions in SCNO. A change in charges associated with surrounding ions after the formation of oxygen vacancy due to the redistribution of electron densities. However, the charge associated with Sr (+1.59) remain the same with or without oxygen vacancy formation. This could be correlated with the redox inactivity of Sr cation[59]. Along with Sr, Nb ions present in the BO plane had also been observed to be redox inactive. The high oxidation state of Nb5+^{5+} and low electronegativity, along with redox inactivity, could be responsible for a high work function for oxygen vacancy creation[60, 61]. The studies performed by Greiner et al.[61], Wang et al.[62], and Hu et al.[63] also reported Nb cations resulting in higher oxygen vacancy formation energies. On oxygen vacancy formation in the SrO plane or CoNbO plane, Co ions are observed to reduce more, hence favoring the oxygen vacancy creation in the structure[58]. As also evident from the Bader charges, Nb cations are reduced by only 1.42 and 1.78% while Co cations are reduced by 3.57 and 4.28% on oxygen vacancy creation in CoNbO and SrO planes, respectively. On the other hand, the redox ability of Co ions (4.44% and 5.66% on oxygen vacancy creation in the CoO and SrO plane, respectively) in SCO favors oxygen vacancies by reducing the energy penalty for oxygen vacancy creation, and the redox inability of Nb5+^{5+} (only 2.82%) hinders the formation of oxygen vacancies in SNO.

MaterialOxygen vacant plane/IonSrCoNbO
Sr2CoNbO6−δSr_{2}CoNbO_{6-\delta}Perfect1.591.402.81-1.23
Sr2CoNbO6−δSr_{2}CoNbO_{6-\delta}CoNbO1.591.35 (3.57%)2.77 (1.42%)-1.24
Sr2CoNbO6−δSr_{2}CoNbO_{6-\delta}SrO1.591.34 (4.28%)2.76 (1.78%)-1.24
Perfect1.601.59--1.07
Sr2Co2O6−δ\mathrm{Sr}_{2}\mathrm{Co}_{2}\mathrm{O}_{6-\delta}CoO1.601.52 (4.44%)--1.06
Sr2Co2O6−δ\mathrm{Sr}_{2}\mathrm{Co}_{2}\mathrm{O}_{6-\delta}SrO1.601.50 (5.66%)--1.06
Sr2Nb2O6−δ\mathrm{Sr}_{2}\mathrm{Nb}_{2}\mathrm{O}_{6-\delta}Perfect1.59-2.48-1.36
Sr2Nb2O6−δ\mathrm{Sr}_{2}\mathrm{Nb}_{2}\mathrm{O}_{6-\delta}NbO1.58-2.41 (2.82%)-1.36
Sr2Nb2O6−δ\mathrm{Sr}_{2}\mathrm{Nb}_{2}\mathrm{O}_{6-\delta}SrO1.58-2.41 (2.82 %)-1.36

Table 3. Bader charges associated with Sr, Co, Nb, and O ions in SCNO, SCO, and SNO systems.

To get further insights into the favorable pattern of oxygen vacancy sites, increased concentration of oxygen vacancies is considered for estimation of EOVE_{\mathrm{OV}}. In order to find the minimum energy non-stoichiometric structures with increasing concentration of oxygen vacancies, EOVE_{\mathrm{OV}} for possible oxygen vacant sites in the SrO and CoNbO planes are calculated, Figure 2(a). The data on EOVE_{\mathrm{OV}}s’ with concentrations is given in Table S2. It was observed that with the increasing concentrations of oxygen vacancies, the EOVE_{\mathrm{OV}} shows the same trend among CoNbO and SrO planes as observed for the case of δ=0.125\delta= 0.125. The EOVE_{\mathrm{OV}}s’ are observed to be 158.73 kJ/mol, 276.21 kJ/mol, and 491.39 kJ/mol for the CoNbO plane and 107.53 kJ/mol, 161.28 kJ/mol and 354.53 kJ/mol for SrO plane for δ=0.125\delta= 0.125, 0.25, and 0.375, respectively. The linear trend of EOVE_{\mathrm{OV}} with oxygen non-stoichiometry δ=0.125\delta= 0.125-0.375 suggests stability of the perovskite structure under these oxygen vacancy concentrations. The EOVE_{\mathrm{OV}} is observed to be very high for δ=0.5\delta= 0.5 (656.89 kJ/mol for the CoNbO plane and 437.60 kJ/mol for the SrO plane). This implies that the oxygen vacancy content of δ=0.5\delta= 0.5 and beyond could only be achieved at the cost of a very high energy penalty. This could lead to the saturation of oxygen vacancy concentration in SCNO to δ=0.375\delta= 0.375 and instability of perovskite oxide after increasing the oxygen vacancy content. Figure 2(b, Figure 2c) represents the most favorable oxygen vacancy sites for δ=1\delta= 1 in CoNbO and SrO planes, respectively. As discernible from the Figure, the vacancies prefer to form row-wise in available sites, making a tunnel-like pathway for oxygen anion transport in the material. Similar observations were reported by Maiti et al.[64] on perovskite oxides, and Prassana et al.[65] and Kim et al.[66] in brown millerite structures.

Trend of EOV with increasing oxygen non-stoichiometry and favorable vacancies for SCNO

Figure 2. (a) Trend of EOVE_{\mathrm{OV}} with increasing oxygen non-stoichiometry (δ=0.125\delta= 0.125-1). The favorable vacancies (depicted as black color sphere) for SCNO in (b) the CoNbO and (c) the SrO planes.

MD simulations are performed to estimate the oxygen anion diffusivity in bulk SCNO. Since oxygen vacancy formation energies are considered descriptor for oxygen anion diffusivity[67], SCNO structure is modeled with δ=0.25\delta= 0.25{sup}18. In order to maintain the overall charge neutrality, the Co ions oxidation state is modeled to be +2.5. The oxygen anion diffusivity is obtained using mean square displacement (MSD) vs. time data, as shown in {xref}Figure 3(a)`, using the expression

MSD=6Dt+B,\mathrm{MSD} = 6Dt + B,

where D, B, and t represent the oxygen anion diffusivity, a constant, and time, respectively.

MSD versus time data and oxygen anion density profile

Figure 3. (a) MSD vs. time data extracted on equilibrated structures, (b) oxygen anion density profile of SCNO at 873 K temperature.

As evident from Table 4, the oxygen anion diffusivity is thermally activated in SCNO. Despite the presence of Nb5+^{5+}, hindering the formation of oxygen vacancies, it was observed that oxygen anion diffusivity for SCNO (8.6×10−88.6 \times10^{-8} cm2^{2}/sec at 873 K temperature) comparable with the other potential cathode materials like La1−x_{1-x}Srx_xCoO3−δ_{3-\delta} (2.73×10−92.73 \times10^{-9} cm2^{2}/sec35^{35} for La0.5_{0.5}Sr0.5_{0.5}CoO3−δ_{3-\delta} and 5.47×10−95.47 \times10^{-9} cm2^{2}/sec35^{35} for La0.5_{0.5}Sr0.5_{0.5}Co0.95_{0.95}Nb0.05_{0.05}O3−δ_{3-\delta} at 873 K), LnBaCo2_2O6−δ_{6-\delta} (5×10−85 \times10^{-8} cm2^{2}/sec68^{68} for GdBaCo2_2O5.5_{5.5}, 7.5×10−87.5 \times10^{-8} cm2^{2}/sec68^{68} for GdBa0.5_{0.5}Sr0.5_{0.5}Co2−x_{2-x}Fex_xO6−δ_{6-\delta}, 1.76×10−71.76 \times10^{-7} cm2^{2}/sec28^{28} for NdBaCo2_2O6−δ_{6-\delta} at 873 K). Activation energy of oxygen anion diffusion in SCNO is estimated using the Arrhenius equation for thermally activated diffusivities

Temperature (K)DD (×10−7\times10^{-7} cm2^{2} sec−1^{-1})
6730.22 ±\pm 0.19
7730.44 ±\pm 0.24
8730.86 ±\pm 0.23
9731.56 ±\pm 0.31
10732.69 ±\pm 0.22
11734.38 ±\pm 0.12
12735.02 ±\pm 0.27

Table 4. Oxygen anion diffusivity in SCNO extracted from MSD vs. time data for 1 ns on equilibrated structures.

D=D0e−EakBT,D = D_0 e^{-\frac{E_a}{k_{\mathrm{B}}T}},

where EaE_a and kBk_{\mathrm{B}} represent the activation energy associated with oxygen anion diffusion and Boltzmann constant, respectively. D0D_0 and TT represent the pre-exponential factor and temperature, respectively. The activation energy for oxygen anion diffusion associated with SCNO is estimated as 38.48 kJ/mol (Figure S2). This is observed to be improved when compared with reported layered perovskite SOFC cathodes like NdBaCo2_2O6−δ_{6-\delta} (40.82 kJ/mol28^{28}), GdBaCo2_2O6−δ_{6-\delta} (50.8 kJ/mol68^{68}) and PrBaCo2_2O6−δ_{6-\delta} (98.4 kJ/mol69^{69}).

Surface EOV_{\mathrm{OV}} could provide a better description of the electrocatalytic performance of SCNO as oxygen anion incorporation reaction takes place on the surface. To calculate surface EOV_{\mathrm{OV}}, SCNO surface slabs with CoNb/Sr and Sr/CoNb terminations (where A/B represent A ions present on the top-most layer and B ions present in the sublayer of the slab) were created along (001) direction (shown in Figure 4(a, Figure 4b)). Subsequently, oxygen vacancies are created in the respective top surfaces of the slabs. A lower surface EOVE_{\mathrm{OV}} on the surface (27.61 kJ/mol for CoNb/Sr and 49.74 kJ/mol for Sr/CoNb slabs) is observed as compared to the bulk (Table 2). A similar trend of a lower surface EOVE_{\mathrm{OV}} is reported by Zhukovskii et al. in PbTiO3_3, PbZrO3_3, and SrTiO3_3 perovskites oxides[70]. Previous studies performed by Walsh et al. have shown higher EOVE_{\mathrm{OV}} for higher coordination numbers in In2_2O3_3[71]. For example, the EOVE_{\mathrm{OV}} for a site with 4 coordination number is reported as 288.96 kJ/mol, whereas for the oxygen vacancy site with 3 coordination number is reported to be 207.36 kJ/mol[71]. The oxygen vacancy sites at the surface and bulk differ by coordination number. An opposite trend of oxygen vacancy formation energies is observed for CoNb/Sr and Sr/CoNb terminated surface slabs than bulk. The EOVE_{\mathrm{OV}} for the top surface layer of the CoNb/Sr terminated slab (27.61 kJ/mol) is observed to be lower than that of the Sr/CoNb terminated slab (49.74 kJ/mol). It was therefore anticipated that the distorted bonding pattern of Nb − O on the surface was not able to influence the surface EOVE_{\mathrm{OV}} as compared to the bulk in the CoNbO plane. Hence, the dominating nature of Co in terms of redox ability leads to the reduction in the surface EOVE_{\mathrm{OV}}s’.

Sr/CoNb and Co/Nb surface terminated slabs with oxygen vacancies and comparative surface-energy trend

Figure 4. (a) Sr/CoNb surface terminated slab with oxygen vacancy on the top surface and (b) Co/Nb surface terminated slab with oxygen vacancy on the top surface, sub-surface, 3rd, 4th, 5th, 6th layer in the bulk of SCNO slab, (c) Comparative trend of surface energies of oxygen vacant CoNb/Sr slab.

The observed trend of EOVE_{\mathrm{OV}} in bulk and surface, thus predicts higher oxygen vacancy concentration on the surface and, hence, probable oxygen vacancy defect migration towards the surface. This could further enhance surface oxygen anion diffusion by facilitating oxygen incorporation in SCNO. In order to study the surface oxygen vacancy formation in detail, surface energy calculations are performed with oxygen vacancy at the top surface, sublayer, and bulk (3{sup}rd, 4{sup}th, 5{sup}th, and 6{sup}th) layer of CoNb/Sr surface terminated slab along (001) direction. The surface energies of the oxygen vacant slab are calculated using the expression

γ=12A(Esurface−n×Ebulk),\gamma= \frac{1}{2A}(E_{\mathrm{surface}} - n \times E_{\mathrm{bulk}}),

where EslabE_{\mathrm{slab}} represents the DFT energy of the CoNb/Sr terminated slab with oxygen vacancy at top layer, sublayer, and bulk layers. EbulkE_{\mathrm{bulk}}, nn, and AA represent the energy of the bulk structure, the number of bulk cells in the slab, and the cross-sectional area of the slab. Surface energies provide a good description of the surface stability of a particular termination or orientation[72]. The corresponding structures with oxygen-vacant sites are shown in Figure 4(b). A comparative trend of surface energies for oxygen vacancies is shown in Figure 4(c), and values are provided in Table S3. The EOVE_{\mathrm{OV}} is lowest on the top surface as compared to the sublayers and the bulk layers. This implies that the migration of oxygen vacancies towards the surface. As evident from Table S3, on going from top-surface to bulk, the favorability of oxygen vacancy is decreased. This predicts an enhanced performance on the thin film surface as compared to the bulk. The material is then expected to show higher oxygen surface exchange coefficient and surface oxygen anion diffusion. In order to investigate the oxygen anion diffusion on the surface, the CoNb/Sr and Sr/CoNb surface terminated slabs are modeled with 9,984 atoms and 100 A˚\mathring{\mathrm{A}} vacuum in the zz-direction. The time dynamics of oxygen anions are captured at every fs for 1 ns on equilibrated structures at 873 K. The corresponding surface oxygen anion diffusion is obtained as 2.91×10−7 cm2/sec2.91 \times10^{-7}\,\mathrm{cm}^2/\mathrm{sec} and 2.79×10−7 cm2/sec2.79 \times10^{-7}\,\mathrm{cm}^2/\mathrm{sec} for CoNb/Sr and Sr/CoNb terminated slabs, respectively, as compared to 1.39×10−7 cm2/sec1.39 \times10^{-7}\,\mathrm{cm}^2/\mathrm{sec} for bulk structure at 873 K temperature (Figure S3). This is consistent with aforementioned DFT results on EOVE_{\mathrm{OV}}s’ for bulk and surface slabs.

Sr-containing perovskites, as in the present case of SCNO, are reported to show degrading Sr-cation segregation tendencies. For example, La1−x_{1-x}Srx_xMnO3−δ_{3-\delta} (LSM)[24], La1−x_{1-x}Srx_xCo1−y_{1-y}Fey_yO3−δ_{3-\delta} (LSCF)[26], and LnBaCo2O6−δCo_{2}O_{6-\delta}[28, 29] are reported to show degrading Sr-cation segregation at SOFC operating conditions, affecting the surface stability and hindering the use of these materials due to long-term stability issues. To probe Sr cation segregation, energetic favorability of possible terminations of the surface slab is examined. Figure S4 represents the Sr/CoNb and CoNb/Sr terminated slabs. Surface energy (γ\gamma) analysis of stoichiometric Sr/CoNb and CoNb/Sr terminating slabs is performed[28]. The surface energies of Sr/CoNb and CoNb/Sr are estimated to be 6.25 and 6.54 kJ/mol·Å2^{2}, respectively. The surface energy of the Sr terminating slab Sr/CoNb is observed to be less than the CoNb/Sr surface slab. This implies tendency for Sr cation surface segregation in the material. In order to study the role of Nb ions in Sr-cation segregation, the model was extended from optimized SCNO to SCO and SNO slab structures, Figure S4. Sr/Co slab is observed to show relatively lower surface energy (4.18 kJ/mol·Å2^{2}) as compared to the Co/Sr slab (4.65 kJ/mol·Å2^{2}) in SCO, whereas Sr/Nb slab (5.44 kJ/mol·Å2^{2}) has the comparable surface energy as compared to Nb/Sr (5.19 kJ/mol·Å2^{2}) in SNO. It clearly indicates the role of Nb ions in enhancing surface stability. Hence, it is predicted that the optimum presence of Co and Nb cations at BB and B′B' sites help suppressing Sr cation segregation towards surface along with significantly enhanced oxygen vacancy formation.

In order to study the time dynamics of Sr-cation segregation in SCNO at 873 K, MD simulations are performed on a surface slab with CoNb/Sr termination. The surface slabs are modeled with a 100 Å vacuum in the zz-direction. The ion dynamics in SCNO is traced at 873 K temperature for 1 ns. The corresponding ion density profile of the SCNO slab is shown in Figure 5 (a). For quantitative measurement, the degree of Sr cation segregation is estimated on the surface as the percentage of Sr-cation migrating from the sub-layer to the top-most layer[28]. The degree of cation segregation is reported as an important parameter for comparative segregation tendencies as well as quantitative measurement of cations separately in NdBa1−x_{1-x}(Sr/Ca)x_xCo2_2O6−δ_{6-\delta}[28]. In MD simulations, the degree of cation segregation is evaluated as the percentage of Sr cation moving from sub-surface to top surface in the slabs after 1 ns of MD run[28]. The SCNO slab consists of 128 Sr atoms in the sublayer for the CoNb/Sr-terminated layer. After ionic dynamics at a temperature of 873 K, an average of 28 Sr atoms migrated from the sublayer to the top surface. Consequently, the degree of Sr-cation segregation is estimated to be 21.875%. To account for the substrate effect, as in the experimental setup, SCNO films are remodeled in the presence of strain. The lattice mismatch strain between SCNO and gadolinium doped ceria (20%) GDC is calculated, as it is reported to be a compatible substrate electrolyte material for SOFCs[1]. Using the lattice parameters of GDC (a=5.42 A˚a = 5.42\ \AA[73]) and SCNO (Table 1), around 2.5% compressive strain is computed. Compressively strained CoNb/Sr and Sr/CoNb terminated slabs are observed to have similar surface energies of 5.83 kJ/mol⋅A˚25.83\ \mathrm{kJ/mol\cdot\AA^2} and 5.44 kJ/mol⋅A˚25.44\ \mathrm{kJ/mol\cdot\AA^2}, respectively. This predicts suppression of Sr-cation segregation in the SCNO film deposited on GDC substrate. In line with the DFT results, the degree of cation segregation as evaluated from MD. With the effect of compressive strain from the GDC substrate, only 8 Sr atoms migrated from the sublayer to the top surface at a temperature of 873 K. Consequently, the degree of Sr-cation segregation was observed to decrease to 6.25%. The corresponding ion density profile of SCNO with 2.5% lattice strain is shown in Figure 7 (b). SCNO film deposited on GDC are observed to be more stable with very less Sr-cation segregation. Higher oxidation number of Nb cations and its ability to promote the bonded pattern leads to a better surface stability in the structure. In addition, the compressed state of the film leads to less space available for the Sr cation to segregate on the surface of the film[28]. Theoretical investigation predicts SCNO films deposited on GDC to show significantly reduced Sr-cation segregation with improved electrocatalytic performance for IT-SOFCs.

Cation distortion profiles for (Co, Nb)/Sr terminated slabs of SCNO

Figure 5. Cation distortion profiles for (Co, Nb)/Sr terminated slabs of SCNO in (a) unstrained and (b) compressively strained state at 873 K.

XPS spectra for Sr, Co, Nb, and O in SCNO powder and thin films

Figure 7. XPS spectrum for (a) Sr, (b) Co, (c) Nb, and (d) O in SCNO powder, and 40 and 80 nm thin films.

Subsequently, thin films of SCNO on GDC pallet are fabricated experimentally using PLD. The XRD patterns of 40 and 80 nm SCNO films are shown in Figure 6 (a). As discernible from the Figure, the GDC substrate shows distinct peaks that match well with its corresponding JCPDS: 75-016. The SCNO peak intensity is lower for the thin film than the bulk structure. The most prominent peak in the SCNO film appears at 31.91°, and the bulk structure shows the desired phase. The FESEM images in Figure 6 (b) revealed a dense surface with connected grain boundaries for the bulk SCNO. The cross-section images in Figure 6 (c, d) show a uniformly deposited dense film with a clear interface between the electrode and electrolyte, and thicknesses of approximately ~40 and ~80 nm, respectively. This indicates the formation of a geometrically well-defined structure. In order to probe the oxygen non-stoichiometry (δ\delta) in the structure, thermogravimetric analysis was performed. The calculated δ\delta values at different temperatures and associated plot is shown in Table S4 and Figure S6. The δ\delta values were observed in the range of 0.26-0.33 for temperature range 473-1073 K temperatures. This observation is in line with the EOV measurements from DFT (Figure 2, Table S2).

XRD pattern, FESEM surface morphology, and cross-section images of SCNO films

Figure 6. (a) XRD pattern of SCNO, 80 and 40 nm thin films of SCNO deposited over the GDC electrolyte using PLD, (b) FESEM image of the surface morphology of the SCNO bulk material, the cross-section of a thin film of SCNO on GDC substrate with (c) ~80 nm and (d) ~40 nm thickness.

The XPS spectrum was analyzed using SCNO as-synthesis and thin films to investigate the possible valence state charges of the associated elements. In addition, XPS spectrum is used to probe the surface [29, 74] for Sr-cation segregation tendencies. Figure 7 (a) presents the spectra of Sr 3d3d electrons for bulk SCNO and thin films placed on a GDC electrolyte. The Sr spectra display two distinct peaks that align with the crystal lattice of the double perovskite structure. The peaks are characterized by energy values of 131.4 and 133.2 eV and are observed to be associated with Sr2+Sr^{2+} 3d5/23d_{5/2} and 3d3/23d_{3/2} lattices, respectively[75]. No evidence of Sr segregation was observed in the XPS spectrum[25]. Sr cations at the AA-site are observed to preserve their oxidation state, consistent with the Bader charges analysis. The XPS spectrum of Co 2p is shown in Figure 7 (b), which shows the co-existence of Co3+Co^{3+} and Co2+Co^{2+}. The deconvoluted XPS peaks at binding energies 779.56 and 795.28 eV ascribed to the 2p3/22p_{3/2} and 2p1/22p_{1/2} electrons, respectively, of trivalent Co3+Co^{3+}. The peaks at 781.41 and 796.66 eV are attributed to the 2p3/22p_{3/2} and 2p1/22p_{1/2} electrons, respectively, of the bivalent Co2+Co^{2+}. The peaks appearing at 786.38 and 801.05 eV are attributed to 80 and 40 nm thin films[76, 77, 78], respectively. The concentration of Co3+Co^{3+} is observed to be higher than the Co2+Co^{2+} state in thin films as compared to bulk powder. This occurs to maintain the charge neutrality in the structure[79]. The XPS analysis shows that the change in valence happens exclusively at the Co-site. We observed two peaks for Nb at 206 and 208.8 eV associated with 3d5/23d_{5/2} and 3d3/23d_{3/2}, respectively (Figure 7 (c)). The symmetric nature of Nb XPS predicts +5 single oxidation state[80, 81]. In line with the bader charge analysis, Co cation is observed to be in a multivalent oxidation state, showing its redox ability, whereas Nb is observed with only +5 oxidation state, indicating its redox inability. The OO 1s spectra of the as-synthesized SCNO indicates the presence of oxygen vacancies (Figure 7 (d)). The OO 1s core-level spectra of oxygen lattice (OlatticeO_{\mathrm{lattice}}) and adsorbed oxygen (OadsorbedO_{\mathrm{adsorbed}}) are found to be at 528.70 and 531.21 eV, respectively for SCNO thin films[82, 83, 84, 85].

The ORR activity of SCNO was investigated using the symmetric cell configuration of SCNO||SDC||SCNO. The EIS of symmetric cells contains information about processes involved in ORR, which are further analyzed by using the DRT technique[55]. The DRT deconvolutes the EIS response by separating the ORR processes into a number of sub-steps like gas diffusion, O2O_{2} surface adsorption, adsorption-dissociation, charge transfer, and oxygen ion migration from the electrode to the electrolyte interface. The semi-arc in EIS represents the polarization resistance. DRT response indicates the peaks determining the rate-controlling steps involved in the polarization response. The EIS of a symmetric cell with thin film electrodes of 40 nm and 80 nm thickness and a porous electrode are shown in Figure 8 (a-c). The polarization resistance (RpR_{\mathrm{p}}) for 40 and 80 nm dense thin film symmetric cells are observed between 0.329 - 0.241 Ω cm2^{2} and 1.095 - 0.438 Ω cm2^{2}, respectively, in the temperature range of 773 - 973 K in air atmosphere. The results indicate higher ORR activity with increasing temperature and decreasing thin film thickness. There is an absence of the Warburg-type component in polarization spectra, which indicates that the electrode's dense thin film microstructure is unlikely to promote gas-phase migration to the triple-phase boundary (TPB).

Impedance spectra and DRT analysis

Figure 8. Impedance spectra and DRT analysis of (a & d) ~40 nm (b & e) ~80 nm dense thin film, and (c & f) porous electrode of SCNO double perovskite symmetric cell.

Furthermore, the impedance spectra shown in Figure 8 (a, b) were deconvoluted using the DRT method. The DRT technique identifies and separates individual sub-processes by their distinct relaxation timings[86, 87]. The low-frequency P1 is associated with oxygen adsorption, bulk diffusion, and catalytic dissociation. The intermediate frequency P2 is correlated with the charge transfer, whereas the high-frequency P3 is associated with the interfaces between electrodes and electrolytes[88, 89]. Figure 8 (d, e) illustrates the DRT curve for dense thin film microstructure electrodes with 40 and 80 nm thicknesses, respectively. The single peak P1 was observed in the DRT response of a 40 nm thin film symmetric cell, which is associated with oxygen ion transport that predominantly takes place through the bulk diffusion channel[90, 91]. When the temperature increases, there is a noticeable reduction in the peak area, indicating an enhancement in the activity of the ORR. In 80 nm thin film DRT, a peak P2 was observed in a very small magnitude and demonstrated a wide association with higher frequency phenomena, such as the transport of ions and the transfer of charges at the interfaces between the electrode and electrolyte. Qiu et al. observed a comparable pattern indicating that an increase in electrode thickness resulted in the emergence of a rate-limiting process for the ORR[92]. According to the aforementioned hypothesis, the dissociation of oxygen species and their subsequent migration through oxygen vacancies occurred due to bulk diffusion through the thin film electrode toward the electrolyte[93].

Furthermore, Figure 8 (f) displays the DRT curve of a porous electrode symmetric cell that encompasses two distinct processes, P1 and P2. The process involves the adsorption and diffusion of oxygen molecules across the electrode surface, where they subsequently break into oxygen atoms. The dissociation takes place followed by bulk diffusion and charge transfer mechanism, which is followed by the reduction of oxygen ions at the porous electrode's TPB. The DRT curve demonstrates that the low-frequency processes, specifically P1, exert a more substantial impact on the overall electrochemical reaction compared to the high-frequency process, P2. Therefore, the rate-limiting mechanism pertains to the absorption of oxygen molecules, their diffusion across the electrode surface, and subsequent dissociation. The findings on dense thin film electrodes indicate that the rate-limiting step is associated with only bulk diffusion, and the porous electrode contains TPB that shows the occurrence of multiple processes for oxygen ion transfer[94].

As SCNO is found to have a high surface stability, ORR activity of SCNO is studied in full cell configuration. A full cell with a NiO anode support was constructed to assess the SOFC performance of the cell. The cell was built by applying a GDC electrolyte layer with a thickness of approximately 500 μm500\ \mu\mathrm{m}, followed by a SCNO cathode. The cell was then tested at temperatures ranging from 773 – 973 K. The anode was exposed to a 3% humidified H2H_2 fuel, while the cathode was exposed to air. The full cell open circuit voltage (OCV) is observed at roughly 0.981 V at 973 K. This observation indicates that the cell is effectively sealed. Figure 9 (a) shows the full cell's current density-power density (I-P) and current density-voltage (I-V) curves. The SCNO cathode exhibits peak power densities of 0.421, 0.540, and 0.633 W/cm2^2 at 773, 873, and 973 K, respectively. The full cell performance of SCNO is observed to be enhanced as compared to other double perovskite oxides probed in literature (Table S6). The EIS was conducted under the OCV condition, Figure 9 (b). The RpR_\mathrm{p} extracted from the Nyquist plot were observed as 0.509, 0.407, and 0.254 Ω\Omega cm2^2 at 773, 873, and 973 K, respectively. The observed enhancement in electrochemical performance at intermediate temperatures can be attributed to the increased diffusion of ions. We observed a decrease in the resistance encountered during charge transfer and a corresponding enhancement in the activity of the ORR.

I-P and I-V curves, and EIS

Figure 9. (a) I-P, I-V curves, and (b) EIS of anode-supported NiO-GDC|GDC|GDC-SCNO.

Conclusions

SCNO perovskite oxide is investigated as a promising cathode material for IT-SOFCs. Despite the presence of Sr at the A-site, SCNO is observed to demonstrate a high surface stability under SOFC operating conditions. A combination of DFT and MD simulations show that Nb at the B′-site, effectively suppresses Sr-cation segregation, enhancing material stability. Our structural studies, simulating the impact of GDC substrate compression using DFT and MD, further indicate a reduced Sr-cation segregation. However, Nb’s low electronegativity, stable configuration, and less reducible nature also hinder the formation of oxygen vacancy. On the other hand, the highly redox-active Co at the B-site is found to favor oxygen vacancy formation. Hence, Co at the B-site and Nb at the B′-site together position SCNO as a strong candidate with enhanced surface stability and electrocatalytic performance.

Further, SCNO was synthesized via an auto-combustion method, and characterization using X-ray diffraction confirmed successful phase formation in both the SCNO powder and thin films deposited on GDC. The observed oxidation states of elements in SCNO using XPS were found to be consistent with the DFT-based Bader charge analysis. Electrochemical testing of a single cell with SCNO as the cathode yielded a power density of 0.633 W/cm20.633\ \mathrm{W}/\mathrm{cm}^{2} at 973 K. The ORR mechanism was analyzed using EIS and DRT analysis. We observed bulk diffusion as the primary performance-limiting factor, especially with increasing electrode thickness. This study provides insights into identifying performance-limiting mechanisms through a combined theoretical and experimental approach and positions SCNO as a high-performance cathode material for IT-SOFCs.

Conflicts of interest

The authors declare no conflicts of interest. They have no known financial interests or personal relationships that could have influenced the work presented in this paper.

Data availability

The data supporting this article has been included as part of the Supplementary Information.

Acknowledgments

JK acknowledges the financial support from the Council of Scientific & Industrial Research (CSIR), India [Grant No. 09/086(1412)/2019-EMR-I]. MAH acknowledges the support from the Department of Science and Technology, India, under DST/TDT/AM/2022/138 (G)/2. The results presented in this paper are derived from computations performed on the High-Performance Computing cluster, Padum, at the Indian Institute of Technology Delhi and PARAM Rudra supercomputing facility at Inter University Accelerator Centre Delhi.

References

  1. [1]Ormerod, R. M. Solid Oxide Fuel Cells. Chem. Soc. Rev. 2003, 32 (1), 17-28. https://doi.org/10.1039/b105764m.
  2. [2]Adler, S. B. Factors Governing Oxygen Reduction in Solid Oxide Fuel Cell Cathodes. Chem. Rev. 2004, 104 (10), 4791-4843. https://doi.org/10.1021/cr020724o.
  3. [3]Liu, M.; Lynch, M. E.; Blinn, K.; Alamgir, F. M.; Choi, Y. Rational SOFC Material Design: New Advances and Tools. Mater. Today 2011, 14 (11), 534-546. https://doi.org/10.1016/S1369-7021(11)70279-6.
  4. [4]Connor, P. A.; Yue, X.; Savaniu, C. D.; Price, R.; Triantafyllou, G.; Cassidy, M.; Kerherve, G.; Payne, D. J.; Maher, R. C.; Cohen, L. F.; Tomov, R. I.; Glowacki, B. A.; Kumar, R. V.; Irvine, J. T. S. Tailoring SOFC Electrode Microstructures for Improved Performance. Advanced Energy Materials. 2018. https://doi.org/10.1002/aenm.201800120.
  5. [5]Sun, C.; Alonso, J. A.; Bian, J. Recent Advances in Perovskite-Type Oxides for Energy Conversion and Storage Applications. Adv. Energy Mater. 2021, 11 (2), 2000459. https://doi.org/10.1002/aenm.202000459.
  6. [6]Jiang, L.; Wei, T.; Huang, Y. Review-Double-Perovskite Electrode Design Strategies and Research Progress for SOFCs. J. Electrochem. Soc. 2022, 169 (6), 064508. https://doi.org/10.1149/1945- 7111/ac725e.
  7. [7]Deng, Z. Q.; Smit, J. P.; Niu, H. J.; Evans, G.; Li, M. R.; Xu, Z. L.; Claridge, J. B.; Rosseinsky, M. J. B Cation Ordered Double Perovskite Ba₂CoMo₀.₅Nb₀.₅O₆-δ as a Potential SOFC Cathode. Chem. Mater. 2009, 21 (21), 5154-5162. https://doi.org/10.1021/cm902094q.
  8. [8]Taylor, A. E.; Morrow, R.; Lumsden, M. D.; Calder, S.; Upton, M. H.; Kolesnikov, A. I.; Stone, M. B.; Fishman, R. S.; Paramekanti, A.; Woodward, P. M.; Christianson, A. D. Origin of Magnetic Excitation Gap in Double Perovskite Sr₂FeOsO₆. Phys. Rev. B 2018, 98 (21), 1-6. https://doi.org/10.1103/PhysRevB.98.214422.
  9. [9]Rendón Ramírez, J. M.; Almanza M., O. A.; Cardona, R.; Landínez Téllez, D. A.; Roa-Rojas, J. Structural, Magnetic and Electronic Properties of The Sr₂CoNbO₆ Complex Perovskite. Int. J. Mod. Phys. B 2013, 27 (28), 1-11. https://doi.org/10.1142/S0217979213501713.
  10. [10]Chen, J.; Wang, X.; Hu, Z.; Tjeng, L. H.; Agrestini, S.; Valvidares, M.; Chen, K.; Nataf, L.; Baudelet, F.; Nagao, M.; Inaguma, Y.; Belik, A. A.; Tsujimoto, Y.; Matsushita, Y.; Kolodiazhnyi, T.; Sereika, R.; Tanaka, M.; Yamaura, K. Enhanced Magnetization of the Highest- TC Ferrimagnetic Oxide Sr₂CrOsO₆. Phys. Rev. B 2020, 102 (18), 184418. https://doi.org/10.1103/PhysRevB.102.184418.
  11. [11]Zu, N.; Zhang, Q.; Hao, J.; Zhang, M.; Li, J.; Liu, X.; Li, R. First-Principles Study on Giant Magneto-Optical Kerr Effect in Double Perovskites Sr₂BB′O₆ (B = Cr, Mo, B′ = W, Re, Os). J. Solid State Chem. 2022, 312 (March). https://doi.org/10.1016/j.jssc.2022.123274.
  12. [12]Huang, Y.-H.; Dass, R. I.; Xing, Z.-L.; Goodenough, J. B. Double Perovskites as Anode. Science (80-. ). 2006, 2 (April), 254-258.
  13. [13]Yu, S.; Yang, X.; Wang, Y.; Bi, L. Immobilizing U Cations in Sr₂Fe₂O₆-δ as a New Cathode for Proton-Conducting Solid Oxide Fuel Cells. Ceram. Int. 2022, 48 (19), 28751-28758. https://doi.org/10.1016/j.ceramint.2022.06.219.
  14. [14]Yang, S.; Gu, Y.; Yu, S. The Effect of Mo and Sc Dopants on the Performance of an Sr₂Fe₂O₆ Cathode for Use in Proton-Conducting Solid Oxide Fuel Cells. Mater. Sci. Eng. B 2025, 311 (September 2024), 117836. https://doi.org/10.1016/j.mseb.2024.117836.
  15. [15]Wright, J. H.; Virkar, A. V.; Liu, Q.; Chen, F. Electrical Characterization and Water Sensitivity of Sr₂Fe₁.₅Mo₀.₅O₆-δ as a Possible Solid Oxide Fuel Cell Electrode. J. Power Sources 2013, 237, 13-18. https://doi.org/10.1016/j.jpowsour.2013.02.079.
  16. [16]Tao, S.; Canales-Vázquez, J.; Irvine, J. T. S. Structural and Electrical Properties of the Perovskite Oxide Sr₂FeNbO₆. Chem. Mater. 2004, 16 (11), 2309-2316. https://doi.org/10.1021/cm049923+.
  17. [17]Kumar, A.; Shukla, R.; Pandey, A.; Dalal, S.; Miryala, M.; Ueno, K.; Murakami, M.; Dhaka, R. S. Structural, Transport, Optical, and Electronic Properties of Sr₂CoNbO₆ thin Films. J. Appl. Phys. 2020, 128 (2). https://doi.org/10.1063/1.5134033.
  18. [18]Azcondo, M. T.; Yuste, M.; Pérez-Flores, J. C.; Muñoz-Gil, D.; García-Martín, S.; Muñoz-Noval, A.; Orench, I. P.; García-Alvarado, F.; Amador, U. Defect Chemistry, Electrical Properties, and Evaluation of New Oxides Sr₂CoNb₁-xTiₓO₆-δ (0≤x≤1) as Cathode Materials for Solid Oxide Fuel Cells. ChemSusChem 2017, 10 (14), 2978–2989. https://doi.org/10.1002/cssc.201700648.
  19. [19]Xu, S.; Lin, X.; Ge, B.; Ai, D.; Peng, Z. Conducting Mechanism of Sr₂CoRO₆ (R=Mo, Nb) under Different pO₂. J. Ceram. Soc. Japan 2016, 124 (8), 813–818. https://doi.org/10.2109/jcersj2.16059.
  20. [20]Li, M.; Zhao, M.; Li, F.; Zhou, W.; Peterson, V. K.; Xu, X.; Shao, Z.; Gentle, I.; Zhu, Z. A Niobium and Tantalum Co-Doped Perovskite Cathode for Solid Oxide Fuel Cells Operating below 500 °C. Nat. Commun. 2017, 8 (5), 1-9. https://doi.org/10.1038/ncomms13990.
  21. [21]Dong, Z.; Xia, T.; Li, Q.; Wang, J.; Li, S.; Sun, L.; Huo, L.; Zhao, H. Addressing the Origin of Highly Catalytic Activity of A-Site Sr-Doped Perovskite Cathodes for Intermediate-Temperature Solid Oxide Fuel Cells. Electrochem. commun. 2022, 140 (July), 107341. https://doi.org/10.1016/j.elecom.2022.107341.
  22. [22]Kim, J. H.; Cassidy, M.; Irvine, J. T. S.; Bae, J. Electrochemical Investigation of Composite Cathodes with SmBa₀.₅Sr₀.₅Co₂O₅-δ Cathodes for Intermediate Temperature-Operating Solid Oxide Fuel Cell. Chem. Mater. 2010, 22 (3), 883-892. https://doi.org/10.1021/cm901720w.
  23. [23]Koo, B.; Kim, K.; Kim, J. K.; Kwon, H.; Han, J. W.; Jung, W. C. Sr Segregation in Perovskite Oxides: Why It Happens and How It Exists. Joule 2018, 2 (8), 1476-1499. https://doi.org/10.1016/j.joule.2018.07.016.
  24. [24]Harrison, W. A. Origin of Sr Segregation at La₁-xSrₓMnO₃ Surfaces. Phys. Rev. B - Condens. Matter Mater. Phys. 2011, 83 (15), 1-5. https://doi.org/10.1103/PhysRevB.83.155437.
  25. [25]Lee, W.; Han, J. W.; Chen, Y.; Cai, Z.; Yildiz, B. Cation Size Mismatch and Charge Interactions Drive Dopant Segregation at the Surfaces of Manganite Perovskites. J. Am. Chem. Soc. 2013, 135 (21), 7909-7925. https://doi.org/10.1021/ja3125349.
  26. [26]Ding, H.; Virkar, A. V.; Liu, M.; Liu, F. Suppression of Sr Surface Segregation in La₁-xSrₓCo₁-yFeᵧO₃-δ: A First Principles Study. Phys. Chem. Chem. Phys. 2013, 15 (2), 489-496. https://doi.org/10.1039/c2cp43148c.
  27. [27]Van Doorn, R. H. E.; Bouwmeester, H. J. M.; Burggraaf, A. J. Kinetic Decomposition of La₀.₃Sr₀.₇CoO₃-δ Perovskite Membranes during Oxygen Permeation. Solid State Ionics 1998, 111 (3-4), 263–272. https://doi.org/10.1016/S0167-2738(98)00191-X.
  28. [28]Kala, J.; Anjum, U.; Mani, B. K.; Haider, M. A.; Li, Y.; Zhang, W.; Zheng, Y.; Chen, J.; Yu, B.; Chen, Y.; Liu, M. Controlling Surface Cation Segregation in a Double Perovskite for Oxygen Anion Transport in High Temperature Energy Conversion Devices. Phys. Chem. Chem. Phys. 2023, 25 (33), 22022-22031. https://doi.org/10.1039/d3cp00827d.
  29. [29]Anjum, U.; Khan, T. S.; Agarwal, M.; Haider, M. A. Identifying the Origin of the Limiting Process in a Double Perovskite PrBa₀.₅Sr₀.₅Co₁.₅Fe₀.₅O₅+δ Thin-Film Electrode for Solid Oxide Fuel Cells. ACS Appl. Mater. Interfaces 2019, 11 (28), 25243-25253. https://doi.org/10.1021/acsami.9b06666.
  30. [30]Huber, A. K.; Falk, M.; Rohnke, M.; Luerssen, B.; Amati, M.; Gregoratti, L.; Hesse, D.; Janek, J. In Situ Study of Activation and De-Activation of LSM Fuel Cell Cathodes - Electrochemistry and Surface Analysis of Thin-Film Electrodes. J. Catal. 2012, 294, 79-88. https://doi.org/10.1016/j.jcat.2012.07.010.
  31. [31]Bucher, E.; Sitte, W.; Klauser, F.; Bertel, E. Impact of Humid Atmospheres on Oxygen Exchange Properties, Surface-near Elemental Composition, and Surface Morphology of La₀.₆Sr₀.₄CoO₃-δ. Solid State Ionics 2012, 208, 43-51. https://doi.org/10.1016/j.ssi.2011.12.005.
  32. [32]Xiong, C.; Xu, S.; Li, X.; Liu, T.; Tan, Y.; Zhao, P.; Qiu, P. Surface Regulating and Hetero-Interface Engineering of an LSCF Cathode by CVD for Solid Oxide Fuel Cells: Integration of Improved Electrochemical Performance and Cr-Tolerance. J. Mater. Chem. A 2023, 11 (29), 15760-15768. https://doi.org/10.1039/D3TA02249H.
  33. [33]Koo, B.; Seo, J.; Kim, J. K.; Jung, W. Isovalent Doping: A New Strategy to Suppress Surface Sr Segregation of the Perovskite O₂-Electrode for Solid Oxide Fuel Cells. J. Mater. Chem. A 2020, 8 (27), 13763-13769. https://doi.org/10.1039/D0TA02870C.
  34. [34]Tsvetkov, D. S.; Sereda, V. V.; Malyshkin, D. A.; Ivanov, I. L.; Zuev, A. Y. Chemical Lattice Strain in Nonstoichiometric Oxides: An Overview. J. Mater. Chem. A 2022, 10 (12), 6351-6375. https://doi.org/10.1039/d1ta08407k.
  35. [35]Dhongde, V.; Singh, A.; Kala, J.; Anjum, U.; Haider, M. A.; Basu, S. Radio-Frequency Magnetron Sputtered Thin-Film La0.5Sr0.5Co0.95Nb0.05O3-δ Perovskite Electrodes for Intermediate Temperature Symmetric Solid Oxide Fuel Cell (IT-SSOFC). Mater. Reports Energy 2022, 2 (2), 100095. https://doi.org/10.1016/j.matre.2022.100095.
  36. [36]Tang, M.; Niu, Y.; Muhammad, W.; Muhammad, S.; Zhong, Z.; Muhammad, S.; Pang, Y.; Wan, Z.; Chen, N.; Qiao, L.; Lv, W. Advances in Solid Oxide Fuel Cell Electrolyte Fabrication by Pulsed Laser Deposition. Int. J. Hydrogen Energy 2024, 50, 618-632. https://doi.org/10.1016/j.ijhydene.2023.08.348.
  37. [37]Waits, R. K. Planar Magnetron Sputtering. J Vac Sci Technol 1978, 15 (2), 179-187. https://doi.org/10.1116/1.569451.
  38. [38]Yu, C.; Sokolov, A. S.; Kulik, P.; Harris, V. G. Stoichiometry, Phase, and Texture Evolution in PLD-Grown Hexagonal Barium Ferrite Films as a Function of Laser Process Parameters. J. Alloys Compd. 2020, 814, 152301. https://doi.org/10.1016/j.jallcom.2019.152301.
  39. [39]Abdullah Umer, M.; Cheng, C. Y.; Lai, B. R.; Tseng, C. J.; Chen, S. yuan; Lee, S. W. Growth of Gd0.3Ca2.7Co3.82Cu0.18O9-δ-BaCe0.6Zr0.2Y0.2O3-δ Bulk Heterojunction Cathode Interlayer by Pulsed Laser Deposition for Enhancing Protonic Solid Oxide Fuel Cell Performance. Appl. Surf. Sci. 2023, 638 (April), 158139. https://doi.org/10.1016/j.apsusc.2023.158139.
  40. [40]Choi, S.; Kucharczyk, C. J.; Liang, Y.; Zhang, X.; Takeuchi, I.; Ji, H. Il; Haile, S. M. Exceptional Power Density and Stability at Intermediate Temperatures in Protonic Ceramic Fuel Cells. Nat. Energy 2018, 3 (3), 202-210. https://doi.org/10.1038/s41560-017-0085-9.
  41. [41]Kresse, G.; Furthmüller, J. Efficiency of Ab-Initio Total Energy Calculations for Metals and Semiconductors Using a Plane-Wave Basis Set. Comput. Mater. Sci. 1996, 6 (1), 15-50. https://doi.org/10.1016/0927-0256(96)00008-0.
  42. [42]Kresse, G.; Furthmüller, J. Efficient Iterative Schemes for Ab Initio Total-Energy Calculations Using a Plane-Wave Basis Set. Phys. Rev. B 1996, 54 (16), 11169. https://doi.org/10.1103/PhysRevB.54.11169.
  43. [43]Joubert, D. From Ultrasoft Pseudopotentials to the Projector Augmented-Wave Method. Phys. Rev. B - Condens. Matter Mater. Phys. 1999, 59 (3), 1758-1775. https://doi.org/10.1103/PhysRevB.59.1758.
  44. [44]Perdew, J. P.; Burke, K.; Ernzerhof, M. Generalized Gradient Approximation Made Simple. Phys. Rev. Lett. 1996, 77 (18), 3865-3868. https://doi.org/10.1103/PhysRevLett.77.3865.
  45. [45]Cococcioni, M.; De Gironcoli, S. Linear Response Approach to the Calculation of the Effective Interaction Parameters in the LDA+U Method. Phys. Rev. B - Condens. Matter Mater. Phys. 2005, 71 (3), 1-16. https://doi.org/10.1103/PhysRevB.71.035105.
  46. [46]Thompson, A. P.; Aktulga, H. M.; Berger, R.; Bolintineanu, D. S.; Brown, W. M.; Crozier, P. S.; in ’t Veld, P. J.; Kohlmeyer, A.; Moore, S. G.; Nguyen, T. D.; Shan, R.; Stevens, M. J.; Tranchida, J.; Trott, C.; Plimpton, S. J. LAMMPS - a Flexible Simulation Tool for Particle-Based Materials Modelling at the Atomic, Meso, and Continuum Scales. Comput. Phys. Commun. 2022, 271, 108171. https://doi.org/10.1016/j.cpc.2021.108171.
  47. [47]Swindells, N.; Sykes, C. T He Classical Equation of State of Gaseous Helium , Neon and Argon. 1937, No. 1928, 264-283.
  48. [48]Jensen, F. Introduction to Computational Chemistry; 2007. https://doi.org/10.1007/s00214-013-1372-6.
  49. [49]Swindells, N.; Sykes, C. The Classical Equation of State of Gaseous Helium, Neon and Argon. Proc. R. Soc. London. Ser. A. Math. Phys. Sci. 1938, 168 (933), 264-283. https://doi.org/10.1098/rspa.1938.0173.
  50. [50]You, A.; Be, M.; In, I. The Nose–Hoover Thermostat. 2008, 4074 (June 2006), 4069-4074.
  51. [51]Grubmüller, H.; Heller, H.; Windemuth, A.; Schulten, K. Generalized Verlet Algorithm for Efficient Molecular Dynamics Simulations with Long-Range Interactions. Mol. Simul. 1991, 6 (1-3), 121–142. https://doi.org/10.1080/08927029108022142.
  52. [54]Rodríguez-Carvajal, J. Recent Advances in Magnetic Structure Determination by Neutron Powder Diffraction. Phys. B Phys. Condens. Matter 1993, 192 (1-2), 55–69. https://doi.org/10.1016/0921-4526(93)90108-I.
  53. [55]Wan, T. H.; Saccoccio, M.; Chen, C.; Ciucci, F. Influence of the Discretization Methods on the Distribution of Relaxation Times Deconvolution: Implementing Radial Basis Functions with DRT tools. Electrochim. Acta 2015, 184, 483–499. https://doi.org/10.1016/j.electacta.2015.09.097.
  54. [56]Wang, G. J.; Wang, C. C.; Huang, S. G.; Sun, X. H.; Lei, C. M.; Li, T.; Liu, L. N. Origin of the Colossal Dielectric Properties in Double-Perovskite Sr₂CoNbO₆. AIP Adv. 2013, 3 (2). https://doi.org/10.1063/1.4791763.
  55. [57]Bashir, J.; Shaheen, R. Structural and Complex AC Impedance Spectroscopic Studies of A₂CoNbO₆ (A = Sr, Ba) Ordered Double Perovskites. Solid State Sci. 2011, 13 (5), 993-999. https://doi.org/10.1016/j.solidstatesciences.2011.02.003.
  56. [58]Wexler, R. B.; Gautam, G. S.; Stechel, E. B.; Carter, E. A. Factors Governing Oxygen Vacancy Formation in Oxide Perovskites. J. Am. Chem. Soc. 2021, 143 (33), 13212-13227. https://doi.org/10.1021/jacs.1c05570.
  57. [59]Bang, S.; Lee, Y. M.; Hong, S.; Cho, K. Bin; Nishida, Y.; Seo, M. S.; Sarangi, R.; Fukuzumi, S.; Nam, W. Redox-Inactive Metal Ions Modulate the Reactivity and Oxygen Release of Mononuclear Non-Haem Iron(III)-Peroxo Complexes. Nat. Chem. 2014, 6 (10), 934-940. https://doi.org/10.1038/nchem.2055.
  58. [60]Shen, C.; Liu, Y.; Hu, L.; Li, W.; Liu, X.; Shi, Y.; Jiang, Y.; Zhao, B.; Zhang, J. Regulating Anionic Redox Activity of Lithium-Rich Layered Oxides via LiNbO₃ Integrated Modification. Nano Energy 2022, 101 (June), 107555. https://doi.org/10.1016/j.nanoen.2022.107555.
  59. [61]Greiner, M. T.; Chai, L.; Helander, M. G.; Tang, W. M.; Lu, Z. H. Transition Metal Oxide Work Functions: The Influence of Cation Oxidation State and Oxygen Vacancies. Adv. Funct. Mater. 2012, 22 (21), 4557-4568. https://doi.org/10.1002/adfm.201200615.
  60. [62]Wang, X.; Wang, F. H.; Shang, J. X.; Zhou, Y. S. Ab Initio Studies of Nb Doping Effect on the Formation of Oxygen Vacancy in Rutile TiO₂. J. Phys. Chem. Solids 2012, 73 (1), 84-93. https://doi.org/10.1016/j.jpcs.2011.09.029.
  61. [63]Hu, Z.; Metiu, H. Effect of Dopants on the Energy of Oxygen-Vacancy Formation at the Surface of Ceria: Local or Global? J. Phys. Chem. C 2011, 115 (36), 17898-17909. https://doi.org/10.1021/jp205432r.
  62. [64]Maiti, D.; Daza, Y. A.; Yung, M. M.; Kuhn, J. N.; Bhethanabotla, V. R. Oxygen Vacancy Formation Characteristics in the Bulk and across Different Surface Terminations of La₍₁₋ₓ₎SrₓFe₍₁₋ᵧ₎CoᵧO₍₃₋₆₎ Perovskite Oxides for CO₂ Conversion. J. Mater. Chem. A 2016, 4 (14), 5137-5148. https://doi.org/10.1039/c5ta10284g.
  63. [65]Prasanna, T. R. S.; Navrotsky, A. Energetics of the oxygen vacancy order-disorder transition in Ba₂In₂O₅. Journal of Materials Research 1993, 8, 1484-1486. https://doi.org/10.1557/JMR.1993.1484.
  64. [66]Kim, Y. M.; He, J.; Biegalski, M. D.; Ambaye, H.; Lauter, V.; Christen, H. M.; Pantelides, S. T.; Pennycook, S. J.; Kalinin, S. V.; Borisevich, A. Y. Probing Oxygen Vacancy Concentration and Homogeneity in Solid-Oxide Fuel-Cell Cathode Materials on the Subunit-Cell Level. Nat. Mater. 2012, 11 (10), 888-894. https://doi.org/10.1038/nmat3393.
  65. [67]Muñoz-García, A. B.; Ritzmann, A. M.; Pavone, M.; Keith, J. A.; Carter, E. A. Oxygen Transport in Perovskite-Type Solid Oxide Fuel Cell Materials: Insights from Quantum Mechanics. Acc. Chem. Res. 2014, 47 (11), 3340-3348. https://doi.org/10.1021/ar4003174.
  66. [70]Zhukovskii, Y. F.; Kotomin, E. A.; Piskunov, S.; Ellis, D. E. A Comparative Ab Initio Study of Bulk and Surface Oxygen Vacancies in PbTiO₃, PbZrO₃ and SrTiO₃ Perovskites. Solid State Commun. 2009, 149 (33-34), 1359-1362. https://doi.org/10.1016/j.ssc.2009.05.023.
  67. [71]Walsh, A. Surface Oxygen Vacancy Origin of Electron Accumulation in Indium Oxide. Appl. Phys. Lett. 2011, 98 (26). https://doi.org/10.1063/1.3604811.
  68. [72]Joshi, A.; Anand, T. S.; Kala, J.; Singh, M.; Gupta, A.; Srivastava, R. K.; Nandan, B. Surface-Engineered Cotton Fabric-Derived Functional Carbon Cloth and Its Application in Advanced Lithium-Sulfur Full Cells. ACS Appl. Energy Mater. 2024, 7 (1), 312-325. https://doi.org/10.1021/acsaem.3c02616.
  69. [73]Rahayu, S.; Forrester, J. S.; Kale, G. M.; Ghadiri, M. Promising Solid Electrolyte Material for an IT-SOFC: Crystal Structure of the Cerium Gadolinium Holmium Oxide Ce₀.₈Gd₀.₁Ho₀.₁O₁.₉ between 295 and 1023 K. Acta Crystallogr. Sect. C Struct. Chem. 2018, 74 (2), 236-239. https://doi.org/10.1107/S2053229617017946.
  70. [74]Joshi, A.; Kala, J.; Mani, B. K.; Gupta, A.; Srivastava, R. K.; Nandan, B. Hollow TiO₂@Fe₂O₃ Nanofiber Additives Using Template Based Approach for Capture-Conversion of Polysulfides in Lithium-Sulfur Batteries. Appl. Surf. Sci. 2024, 669 (June), 160559. https://doi.org/10.1016/j.apsusc.2024.160559.
  71. [75]Sosulnikov, M. I.; Teterin, Y. A. X-Ray Photoelectron Studies of Ca, Sr and Ba and Their Oxides and Carbonates. J. Electron Spectros. Relat. Phenomena 1992, 59 (2), 111-126. https://doi.org/10.1016/0368-2048(92)85002-O.
  72. [76]Wei, T.; Zhang, Q.; Huang, Y. H.; Goodenough, J. B. Cobalt-Based Double-Perovskite Symmetrical Electrodes with Low Thermal Expansion for Solid Oxide Fuel Cells. J. Mater. Chem. 2012, 22 (1). https://doi.org/10.1039/c1jm14756k.
  73. [77]Zhou, W.; Sunarso, J.; Zhao, M.; Liang, F.; Klande, T.; Feldhoff, A. A Highly Active Perovskite Electrode for the Oxygen Reduction Reaction Below 600 °C. Angew. Chemie Int. Ed. 2013, 52 (52), 14036-14040. https://doi.org/10.1002/ANIE.201307305.
  74. [78]Ha, M. N.; Lu, G.; Liu, Z.; Wang, L.; Zhao, Z. 3DOM-LaSrCoFeO₆-δ as a Highly Active Catalyst for the Thermal and Photothermal Reduction of CO₂ with H₂O to CH₄. J. Mater. Chem. A 2016, 4 (34). https://doi.org/10.1039/c6ta05402a.
  75. [79]Du, X.; Ai, H.; Chen, M.; Liu, D.; Chen, S.; Wang, X.; Lo, K. H.; Pan, H. PLD-Fabricated Perovskite Oxide Nanofilm as Efficient Electrocatalyst with Highly Enhanced Water Oxidation Performance. Appl. Catal. B Environ. 2020, 272. https://doi.org/10.1016/j.apcatb.2020.119046.
  76. [80]Lu, Y.; Pei, Z.; Wu, H.; Leng, K.; Xia, W.; Zhu, X. Preparation of Ba₂FeNbO₆ Double Perovskite Ceramics from Molten-Salt Synthesized Powders and Their Dielectric and Magnetic Properties. J. Mater. Sci. 2020, 55 (10), 4179-4192. https://doi.org/10.1007/s10853-019-04329-3.
  77. [81]Veena, V. S.; Revathy, R.; Nair, A. A. K.; Rahul, M. T.; Kalarikkal, N.; Manjula Devi, M.; Anand, A.; Veena, R. K.; Sagar, S. Room Temperature Magnetoelectric Effect in Sr₂FeNbO₆ Perovskite: A Theory Supported Experimental Investigation. J. Solid State Chem. 2023, 327 (August), 124286. https://doi.org/10.1016/j.jssc.2023.124286.
  78. [82]Zhu, Y.; Zhong, X.; Jin, S.; Chen, H.; He, Z.; Liu, Q.; Chen, Y. Oxygen Defect Engineering in Double Perovskite Oxides for Effective Water Oxidation. J. Mater. Chem. A 2020, 8 (21). https://doi.org/10.1039/d0ta04362a.
  79. [83]Zhu, Y.; Zhang, L.; Zhao, B.; Chen, H.; Liu, X.; Zhao, R.; Wang, X.; Liu, J.; Chen, Y.; Liu, M. Improving the Activity for Oxygen Evolution Reaction by Tailoring Oxygen Defects in Double Perovskite Oxides. Adv. Funct. Mater. 2019, 29 (34). https://doi.org/10.1002/adfm.201901783.
  80. [84]Yao, C.; Zhang, H.; Liu, X.; Meng, J.; Zhang, X.; Meng, F.; Meng, J. Investigation of Layered Perovskite NdBa₀.₅Sr₀.₂₅Ca₀.₂₅Co₂O₅+δ as Cathode for Solid Oxide Fuel Cells. Ceram. Int. 2018, 44 (11), 12048-12054. https://doi.org/10.1016/j.ceramint.2018.03.206.
  81. [85]He, G.; Liu, X.; Li, R.; Zhai, D.; Liu, Y.; Xie, C.; Hu, P.; Zhen, Q.; Bashir, S.; Liu, J. Silver-Modified Ba₁-xCo₀.₇Fe₀.₂Nb₀.₁O₃-δ Perovskite Performing as a Cathodic Catalyst of Intermediate-Temperature Solid Oxide Fuel Cells. ACS Appl. Mater. Interfaces 2020, 12 (8). https://doi.org/10.1021/acsami.9b19634.
  82. [86]Hanif, M. B.; Gao, J. T.; Shaheen, K.; Wang, Y. P.; Yasir, M.; Zhang, S. L.; Li, C. J.; Li, C. X. Performance Evaluation of Highly Active and Novel La₀.₇Sr₀.₃Ti₀.₁Fe₀.₆Ni₀.₃O₃-δ Material Both as Cathode and Anode for Intermediate-Temperature Symmetrical Solid Oxide Fuel Cell. J. Power Sources 2020, 472. https://doi.org/10.1016/j.jpowsour.2020.228498.
  83. [87]Zhang, Y.; Chen, Y.; Yan, M.; Chen, F. Reconstruction of Relaxation Time Distribution from Linear Electrochemical Impedance Spectroscopy. J. Power Sources 2015, 283. https://doi.org/10.1016/j.jpowsour.2015.02.107.
  84. [88]Meng, X.; Long, G.; Liu, S.; Ji, Y.; Pang, M.; Wang, B.; Lü, S.; Yang, J. Novel BaBi₀.₀₅Co₀.₈Nb₀.₁₅O₃-δ Perovskite Oxide as Cathode Material for Intermediate-Temperature Solid Oxide Fuel Cells. Int. J. Hydrogen Energy 2015, 40 (21), 6935-6941. https://doi.org/10.1016/J.IJHYDENE.2015.04.019.
  85. [89]Zhou, X.; Li, M.; Yang, W.; Hu, H.; Li, J.; Lu, Y.; Wang, X.; Ding, X. Efficient and Stable Symmetrical Solid Oxide Fuel Cell via A-Site Non-Stoichiometry. Electrochim. Acta 2022, 425 (June). https://doi.org/10.1016/j.electacta.2022.140697.
  86. [90]Plonczak, P.; Sorensen, D. R.; Sogaard, M.; Esposito, V.; Hendriksen, P. V. Electrochemical Properties of Dense (La, Sr)MnO₃-δ Films Produced by Pulsed Laser Deposition. Solid State Ionics 2012, 217. https://doi.org/10.1016/j.ssi.2012.03.043.
  87. [91]Usiskin, R. E.; Maruyama, S.; Kucharczyk, C. J.; Takeuchi, I.; Haile, S. M. Probing the Reaction Pathway in (La₀.₈Sr₀.₂)₀.₉₅MnO₃+δ Using Libraries of Thin Film Microelectrodes. J. Mater. Chem. A 2015, 3 (38). https://doi.org/10.1039/c5ta02428e.
  88. [92]Hayd, J.; Ivers-Tiffée, E. Detailed Electrochemical Study on Nanoscaled La₀.₆Sr₀.₄CoO₃-δ SOFC Thin-Film Cathodes in Dry, Humid and CO₂-Containing Atmospheres . J. Electrochem. Soc. 2013, 160 (11). https://doi.org/10.1149/2.026311jes.
  89. [93]Qiu, H.; Jiang, S.; Niu, Y.; Zhang, Q.; Pang, Y.; Su, C. Thickness-Dependent High-Performance Solid Oxide Fuel Cells with Ba₀.₅Sr₀.₅Co₀.₈Fe₀.₂O₃-δ Cathode. Asia-Pacific J. Chem. Eng. 2022, 17 (4), e2769. https://doi.org/10.1002/APJ.2769.
  90. [94]Jose La O’, G.; Ahn, S. J.; Crumlin, E.; Orikasa, Y.; Biegalski, M. D.; Christen, H. M.; Shao-Horn, Y. Catalytic Activity Enhancement for Oxygen Reduction on Epitaxial Perovskite Thin Films for Solid-Oxide Fuel Cells. Angew. Chemie - Int. Ed. 2010, 49 (31). https://doi.org/10.1002/anie.201001922.

Paper details

vlnc:W_2vr97xbt
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents