WorksPhysics and Astronomy
Exploring Mechanisms of Hydration and Carbonation of MgO and Mg(OH)2 in Reactive Magnesium Oxide-based Cements
Abstract
Reactive magnesium oxide (MgO)-based cement (RMC) can play a key role in carbon capture processes. However, knowledge on the driving forces that control the degree of carbonation and hydration and rate of reactions in this system remains limited. In this work, density functional theory-based simulations are used to investigate the physical nature of the reactions taking place during the fabrication of RMCs under ambient conditions. Parametric indicators such as adsorption energies, charge transfer, electron localization function, adsorption/dissociation energy barriers and the mechanisms of interaction of H2O and CO2 molecules with MgO and brucite (Mg(OH)2) clusters are considered. The following hydration and carbonation interactions relevant to RMCs are evaluated i) carbonation of MgO, ii) hydration of MgO, carbonation of hydrated MgO, iii) carbonation of Mg(OH)2, iv) hydration of Mg(OH)2 and v) hydration of carbonated Mg(OH)2. A comparison of the energy barriers and reaction pathways of these mechanisms shows that the carbonation of MgO is hindered by presence of H2O molecules, while the carbonation of Mg(OH)2 is hindered by the formation of initial carbonate and hydrate layers as well as presence of excessed H2O molecules. To compare these finding to bulk mineral surfaces, the interactions of the CO2 and H2O molecules with the MgO(001) and Mg(OH)2 (001) surfaces are studied. Therefore, this work presents deep insights into the physical nature of the reactions and the mechanisms involved in hydrated magnesium carbonates production that can be beneficial for its development.
Introduction
Increasing carbon dioxide () emissions are currently one of the most serious environmental challenges.[1] Cement manufacturing, and specifically the manufacture of ordinary Portland cement (OPC), is the source of 5%–7% of global greenhouse gas emissions.[2] Limestone (), the conventional feedstock for OPC manufacturing, is excavated, crushed and sintered with other materials in a cement kiln at temperatures reaching 1450°C to produce clinker. During the calcination of , is directly emitted (i.e. ), causing 50%–60% of the total emissions from OPC production.[3] From the standpoint of sustainable development, the cement industry is seeking alternatives to reduce emissions while maintaining the same performance.[4]
Among the proposed alternative binders, Mg-based cements have attracted attention for their promise as partial replacements for OPC.[5] When magnesium oxide () is derived from Mg silicates (e.g. olivine and serpentine), less environmental and economic impact is generated.[6] The net emissions from the carbonation of these binders may be 73% lower than OPC,[7] and, therefore, may potentially lead to the formation of carbon-negative cements. Moreover, the lower production temperature of reactive MgO–based cement (RMC) compared to that of OPC (i.e. 700–1000°C vs. 1450°C), and its potential to gain strength through its reaction with , has attracted special attention.[7]
Considering the need for the rapid development of carbon capture and utilisation technology,[8] the main advantage of RMCs produced from Mg–Si minerals in concrete formulations is their ability to absorb and permanently store in the form of stable carbonates during the carbonation process, when MgO is sourced from low-CO feedstocks.[9] In such processes, MgO reacts with water () to form brucite (), which generally has a weak and porous structure.[5, 10] However, hydrated MgO has a strong ability to absorb and produce carbonated products at a strength useful for construction purposes.[11] In other words, the dissolution of MgO through hydration results in the formation of , which is then carbonated according to the following reaction and produces a range of hydrated magnesium carbonates (HMCs): . Nesquehonite () is the most commonly obtained HMC, yet other phases such as hydromagnesite (), dypingite() and artinite () can also be present.[12, 13]
Recent experimental studies have examined the formation of HMCs through the hydration and carbonation of RMC. In particular, improvement of the hydration and mechanical performance of carbonated MgO-based systems has been observed with the introduction of various hydration agents at different concentrations.[14] In this way, the simultaneous use of magnesium acetate at 0.05 M and carbonate seeds (up to 1% of cement content) improved mechanical performance of carbonated RMC concrete mixes.[15] However, investigation of the physical nature of mechanisms involved in the reactions of HMC production is still immature. One of the reasons for this is the limitation of available experimental methods for the determination of such processes occurring at the nanoscale in bulk materials.
Theoretical approaches with predictive capabilities, such as those based on the density functional theory (DFT), show a high capability for determining the most stable atomic structures and exploring the physical and chemical properties of these finite systems.[16, 17, 18, 19] Computational approaches have been successfully utilised to investigate in depth the mechanisms related to the formation of HMCs. For instance, the structure, formation energy and electronic properties of four commonly exposed surfaces of nesquehonite crystal have been studied using DFT-based calculations.[16] In another computational work the activity and selectivity of MgO surfaces for conversion have been studied.[20] In particular, the adsorption and dissociation of , as well as its subsequent hydrogenation to HOCO and HCOO, on various MgO surfaces, have been investigated. It has been shown that the direct dissociation of on MgO is thermodynamically unfavourable because of high reaction energy, while hydrogenation of to HCOO by hydride H is more feasible on MgO. DFT simulations have also been utilised to compare the adsorption and activation reaction mechanisms of and molecules on hydrogen-assisted MgO(110), pure Ni(111) and Ni/MgO interfaces.[21] Computational methods have also been applied for a deeper exploration of the effects of various promoters and dopants upon adsorption on the MgO−CaO(100) surface.[22] Theoretically supported experimental infrared-based studies have been performed to identify the structure of the species adsorbed on the various MgO surface.[23] It has been shown that the active site towards , which is a Lewis acid, differs from that for the deprotonating adsorption of Brønsted acids. Another experimentally supported computational study provided a comprehensive study on the adsorption on the MgO and surfaces.[24] It has been found that chemisorption of on the MgO surface is facilitated by the presence of .
Since the reaction degrees of MgO and are relatively low (ca. 50%), they reduce the effectiveness of utilization to form a cementitious binder.[25] Furthermore, because the transformation of HMCs shows mixed diffusion and reaction-limited control, and it proceeds through the production of metastable intermediates, the specifics of nesquehonite conversion to other HMCs remains unclear. The conversion of these metastable intermediates also raises concerns about the durability of cement.[26] Therefore, insights into the potential reactions in the system, and an understanding of the nature of kinetic hindrance in MgO and carbonation and hydration at the atomic level, are of immediate interest.
In this work, the physical nature of the mechanisms for HMC production on MgO and nanoclusters is considered using DFT calculations. Clusters are collections of atoms that act as a link between gases and bulk phase materials (liquids and solids). They are considerably large to be considered as molecules while considerably small to be classified as liquids or solids, and almost all of the atoms in a cluster are on or near its surface, making them a good choice for considering surface reactions.[27] In addition, robust reactions at oxide surfaces, such as the exchange rates of molecules on the surface can be reliably predicted using molecular-simulation methods.[28]
Here, the interaction of these nanoclusters of potentially promising RMC raw materials with ambient molecules ( and ) is considered. The mechanism of the following reactions is investigated: carbonation of MgO, hydration of MgO, carbonation of hydrated MgO, carbonation of , hydration of and hydration of carbonated . Notably, even though through-solution dissolution–precipitation reactions are often the dominating reactions in HMC synthesis, surface carbonation can become important to the overall carbonation kinetics by hindering further reactions, including dissolution. Understanding the mechanisms of these reactions is accomplished by calculating adsorption energy, charge transfer, electron localization function and adsorption/dissociation energy barriers of and upon reactions with the MgO and clusters. To gain further insights into the difference between MgO and clusters and bulks, the interactions between the surfaces of bulk MgO and with and molecules are also investigated. The results also shed light on the underlying reason for the hindrance of carbonation of MgO and that has been previously observed experimentally. Therefore, the results of this work reveal the mechanisms that take place during HMC production that can further facilitate the development of their production.
Methods
The calculations were carried out based on DFT using the Vienna ab-initio simulation package[29] where the electron–ion interactions were simulated via the projector augmented wave method.[30] The generalized gradient approximation with the of Perdew–Burke–Ernzerhof exchange-correlation function was employed.[31] The most energetically favourable MgO cluster has a cage-like configuration with T symmetry that included six MgO rings and eight MgO to form a shortened octahedron with equivalent Mg and O vertices.[32] The system considered consisted of a MgO cluster placed in a cubic supercell with dimensions of 20 × 20 × 20 Å. A 3 × 3 × 3 k-point sampling was employed for structure optimization calculations, while a 1 × 1 × 1 k-point was used for electronic structure calculations. Mg(OH) cluster consisting of 9 units of Mg(OH)[33] was placed in a cubic cell with dimensions of 30 × 30 × 30 Å. A 1 × 1 × 1 Å k-point sampling was applied for all optimisation and electronic structure calculations. The considered MgO and the Mg(OH) slabs with the (001) cleaved-plane surface were selected based on the previous work.[34] A 2 × 2 × 1 Å and 1 × 1 × 1 Å k-point sampling was used for MgO and Mg(OH) slabs, respectively.
All systems considered were totally optimized to reach atomic forces and total energies less than 0.05 eV Å and 10 eV, respectively. A kinetic energy cut-off of 450 eV was set for all calculations. The van der Waals–corrected functional Becke88 optimisation (optB88)[35] was adopted for the consideration of non-covalent chemical interactions between molecules and clusters. The adsorption energy of the molecule is given by the following equation[36]:
where E is the total energy of the cluster with the adsorbed molecule, E is the total energy of the isolated molecule and E is the total energy of the bare cluster. Under this definition, the negative adsorption energy indicates an exothermic and favourable process. The electrons gained or lost are defined as the difference of valence electrons of an atom in the adsorbed system from the atom in a free molecule or a substrate, according to the equation . The negative and positive values indicate electrons gained and lost, respectively.
The charge transfer between the molecule and the cluster is given by the charge density difference (CDD) :
where , and are the charge densities of the cluster with the adsorbed molecule, the bare cluster and the isolated molecule, respectively. The Bader analysis was used to calculate the charge transfer between the molecules and the clusters[37].
The Arrhenius equation is given by the following formula:
where is the rate constant, A is the pre-exponential factor, E is the activation energy or the energy barrier for a reaction, R is the universal gas constant, and T is the absolute temperature.[38]
The electron localisation function (ELF) was calculated to obtain the distribution of electrons in the considered structures. The degree of charge localisation in real space is depicted by the value of the ELF (between 0 and 1), where 0 represents a free electronic state and 1 represents a perfect localisation. An isosurface value of 0.65 was adopted in this work.[39]
The climbing image–nudged elastic band (CI-NEB) method[40] was used to obtain the reaction pathway of the molecule on the cluster. The AIMD simulations were carried out at room temperature of 300 K. The simulation lasted for ps with a time step of 1 fs, and the temperature was controlled by a Nose–Hoover thermostat.[41]
Results and Discussion
MgO interaction with CO and HO. The interaction of the MgO cluster with the CO molecule is considered to simulate the formation of MgO–CO (MgCO) as the main precursor to HMCs. For this, various absorption configurations of the CO molecule on the MgO cluster are considered (more details see Figure S1 in Supporting Information). Figure 1a shows the lowest-energy configuration structure of the CO molecule adsorbed on the MgO cluster, combined with the CDD plot. In the most stable configuration, the O atom of the CO molecule is bonded to the Mg atom of the MgO cluster. The length of the created Mg–O bond is 2.207 Å. The length of the C–O bond of the CO molecule is elongated from 1.174 Å (bare CO) to 1.188 Å (CO after adsorption on MgO). It is also found that the (O–C–O) angle of CO adsorbed on the MgO cluster decreases to 171.94° compared to 179.95° for the bare CO. Table S1 (see Supporting Information) combines the results for the adsorption energy and charge transfer between the CO molecule and the MgO cluster. It is shown that of the CO molecule on the MgO cluster is -0.42 eV. According to the CDD plot (see Figure 1a), the CO molecule acts as an acceptor to the MgO cluster with the charge transfer from the surface to the molecule of 0.092 (see Table S1 in Supporting Information), which can be attributed to the basicity of the MgO cluster, as it can donate a pair of nonbonding electrons following the Lewis base role.[21] The observed elongation of the C–O bond and the enhanced charge transfer between the cluster and molecule suggest a strong interaction between them. The high electronegativity of O atoms of the molecule can be the driving force for the observed charge transfer compared to that of Mg atoms of the cluster. However, the ELF analysis (see Figure 1b) shows that electron density is mainly located at the Mg–O bond, which indicates electron depletion from the surface of the cluster to the CO molecule, and at the O atoms of the CO molecule, indicating that strong covalent bonding remains only within the molecule.

Figure 1. (a) The lowest-energy configuration of the CO₂ molecule physisorbed on the MgO cluster combined with the CDD isosurface plot (0.003 Å). (b) The ELF and (c) DOS and LDOS for the CO₂–physisorbed MgO cluster. (d) The lowest-energy configuration of the CO₂ molecule chemisorbed on the MgO cluster combined with the CDD isosurface plot (0.009 Å). (e) The ELF and (f) DOS and LDOS for the CO₂–chemisorbed MgO cluster. (g) The energy barrier and atomic structures corresponding to the minimum energy pathway for the chemisorption process of the CO₂ molecule on the MgO cluster.
To deeper understand the interaction of the CO molecule with the MgO cluster, density of states (DOS) and local density of states (LDOS) analyses of CO-adsorbed MgO are performed (see Figure 1c). The bare MgO cluster has higher HOMO and HOMO-1 states than the CO molecule, which indicates its tendency to oxidize the molecule, whereas the CO molecule possess LUMO and LUMO+1 states, which verifies its ability to gain electrons. Moreover, strong overlapping of LUMO and LUMO+1 states is observed upon the interaction between the molecule and the cluster, suggesting a strong interaction between them. In addition, AIMD simulations are conducted to study the interaction of the CO molecule with the MgO cluster at room temperature. The AIMD calculations (see Movie 1 in Supporting Information) confirm the possibility of the chemisorption of CO on the MgO cluster at room temperature and suggests a low energy barrier for the reaction, as it is proposed from the and charge transfer calculations. Therefore, the chemisorption process of CO on MgO is further considered.
The chemisorbed configuration of CO is chosen based on the AIMD-obtained configuration (see Figure S2 in Supporting Information). In that case, the length of the Mg–O bond formed between the cluster and the molecule is 2.080 Å, which is shorter than that in the physisorbed state (2.207 Å). The length of the newly formed Mg–O bond in the chemisorbed configuration is 2.092 Å. The C–O bond lengths of the CO molecule are 1.269 Å and 1.266 Å, which are significantly longer than those of the CO in its physisorbed state (1.188 Å). This indicates that C–O bonds of CO are highly elongated upon its interaction with Mg atoms. The (O–C–O) angle of 179.95° of bare CO decreases to 129.69° for CO adsorbed on the MgO cluster. The CDD plot (see Figure 1d) and the Bader charge transfer analysis (see Table S1 in Supporting Information), predict that CO is an acceptor to MgO as it accumulates 0.117 from the MgO cluster. The amount of charge transferred from MgO to chemisorbed CO is higher than that from MgO to physiosorbed CO (see Table S1 in Supporting Information). Furthermore, of CO on MgO in its chemisorbed state is -1.05 eV (see Table S1 in Supporting Information), which is more than twice higher that of CO physiosorbed on MgO. From Figure 1e, which shows ELF of CO chemisorbed on MgO, it is seen that electron localization located on the C–O bond formed between CO and MgO. In addition, strong electron redistribution is observed on O atoms of CO suggesting the formation of covalent bonds between the molecule and the cluster while the C–O covalent bonds of the CO molecule remain stable. That contribute to the depletion of electrons from the surface to the molecule as it is observed in the CCD plot in Figure 1d.
According to the DOS and LDOS plots in Figure 1f, there is a strong hybridization of the HOMO, HOMO-1 and LUMO+1 states of the MgO cluster and the CO molecule, indicating a strong interaction between them and signifying the possibility of chemisorption of the CO molecule on the MgO cluster. The AIMD simulations also suggest that the chemisorption of CO on MgO is favourable (see Movie 1 and Figure S2 in Supporting Information). Thus, the possible reaction mechanism for the transformation process for the CO molecule on the MgO cluster from physiosorbed to chemisorbed state is further studied through NEB approach. The energy profile and related atomic configurations for the initial state (IS), transition state (TS), intermediate states (IM) and final state (FS), showing the transition of the CO molecule from the physisorbed state to the chemisorbed state, are depicted in Figure 1g. TS with an energy level of 0.049 eV proposes the low energy barrier for this transition (see Table S2 in Supporting Information). It seems that the O atom of CO has a high tendency to oxidize the Mg atom of the cluster. This oxidation is expedited at IM3 by the approach and further bonding of the C atom of the molecule to the O of the cluster, which leads to a drop of to 0.001 eV. At FS, the second O atom of CO is bonded to the Mg atom of the cluster, and further drops to -0.617 eV which suggests the reaction is exothermic.
To summarize, the elongation of the C–O bond and the decrease of the (O–C–O) angle of the CO molecule upon its chemisorption on the MgO cluster comparing to physisorption lead to an increase of .[24] In addition, higher charge transfer from the cluster to the CO molecule during chemisorption stabilizes the adsorption of the CO molecule on the cluster[42]. These results are well agreed with found low of exothermic transition of CO from physisorbed state to chemisorbed state and with experimental observations confirming that the calcination of magnesite (MgCO) is an endothermic process.[5] Therefore, the chemisorption of CO on MgO occurs favourably under the reaction conditions.
The reaction of HO with MgO leads to the formation of Mg(OH), a phase that might also undergo carbonation, which results in the HMC formation. Hence, the hydration of the MgO cluster is also investigated. All possible absorption configurations of HO on the MgO cluster are considered (see Figure S3 in Supporting Information). According to Table S1 (see Supporting Information), for the most energetically favourable configuration of adsorbed HO on the MgO cluster (see Figure 2a) is -0.95 eV. In this configuration, the Mg–O bond between the O atom of the HO molecule and the Mg atom of the MgO cluster and the H–O bond between the H atom of the molecule and the O atom of the cluster are formed. The length of the Mg–O and H–O bonds is found to be 2.085 Å and 1.627 Å, respectively. Moreover, the length of the H–O bond of the HO molecule before bonding to the cluster is 0.936 Å, and it is elongated to 1.036 Å after adsorption, signifying the tendency of HO to bind to MgO. According to the Bader charge transfer analysis and the CCD plot (see Figure 2a) the HO molecule is a strong electron acceptor to the cluster with = -1.122 (see Table S1 in Supporting Information). The basicity of the MgO cluster facilitates the electrons transfer from the O atom of the cluster to the HO molecule, while a higher electronegativity of the O atom of the molecule facilitates electron depletion towards H atoms. Such significant charge redistribution between the MgO cluster and the contributes to its adsorption.[36]

Figure 2. (a) The lowest-energy configuration of the HO molecule on the MgO cluster combined with the CDD isosurface plot (0.003 Å-3). (b) The ELF and (c) DOS and LDOS for the HO–adsorbed MgO cluster. (d) The energy barrier and atomic structures corresponding to the minimum energy pathway for the hydration of the MgO cluster.
The ELF plot in Figure 2b shows the electron localization between the O atom of the molecule and the Mg atom of the MgO cluster, as well as the localization between the H atom of the molecule and the O atom of the MgO cluster, which confirms electron depletions at these sites and suggests the formation of the H-O and Mg-O bonds between the molecule and the cluster. The DOS and LDOS plots in Figure 2c display the hybridization of and MgO states at -3.3 eV and 4.9 eV and a weak interaction at 4.4 eV. The conducted AIMD simulation also confirms the dissociation of the molecule on the MgO cluster and formation of the H-O and Mg-O bonds (see Movie 2 and Figure S4 in Supporting Information).
NEB calculations are carried out to show the possible reaction mechanism of the molecule dissociation on the MgO cluster. Figure 2d presents the energy profile and related atomic configurations for the IS, TS, IMs and FS showing the dissociation of the molecule of the MgO cluster. As it is seen, between IS and TS the HO molecule bonding to the MgO cluster through the rotation of the H atom of the molecule (IM1). of the HO molecule dissociation on the MgO cluster at TS is found to be as high as 0.245 eV (see tbl:S2 in Supporting Information). Further reaction at IM2 and IM3 leads to the bonding of the H atom of the HO molecule to the nearest O atom of the cluster and the consequent HO dissociation at FS occurring with an energy release of 0.179 eV. A higher energy release during the carbonation (-0.617 eV) of the MgO cluster compared to that during hydration (-0.179 eV) of the MgO cluster, indicates that the carbonation of the MgO cluster is a more exothermic process than its hydration. Therefore, the carbonated MgO is more thermodynamically stable. However, for carbonation of the MgO cluster is 0.235 eV, which is lower than of 0.245 eV for hydration of the MgO cluster. On the other hand, AIMD simulations suggest that the hydration of the MgO cluster passes faster than its carbonation (see Figure S4 in Supporting Information). Therefore, hydration and carbonation rates of the MgO cluster are compared based on the Arrhenius equation (Eq. (3)), according to which the reaction rate depends on two factors: activation energy of the reaction and pre-exponential factor A. Therefore, besides the calculated , the A factor, describing the frequency of collisions between reactant molecules at a standard concentration, should be taken into consideration for the comparison of hydration and carbonation rates of the MgO cluster. The hydrolysis of the MgO cluster changes its structure due to a break of Mg-O bonds of the MgO cluster upon interaction with HO, while the carbonation of the MgO cluster does not cause the alteration of the MgO cluster. This leads to a significant difference in the A factor for the hydration and carbonation of the cluster. As a result, the hydration of the MgO cluster is faster than its carbonation as it is shown by AIMD simulations (see Figure S4 and Movies 1 and 2 in Supporting Information). This observation is also in line with the fact that of the HO molecule (-0.95 eV) on the MgO cluster is more than 2 times lower than that of the CO molecule (-0.42 eV) on the MgO cluster, which leads to faster hydration reaction. Faster hydration of the MgO cluster is also observed in AIMD simulations (see Figures S4 in Supporting Information) where the adsorption of the HO molecule of the MgO cluster occurs ~3 times faster than that of the CO molecule. Furthermore, to compare the hydration and the carbonation rate of the MgO cluster, AIMD simulations are performed to simulate a CO- and HO-saturated environment, consisting of three CO and three HO molecules (see Movie 3 in Supporting Information). The trajectory of these molecules shows that hydration of MgO is significantly faster than its carbonation (see Figure S5 in Supporting Information), as all three considered HO molecules bond to the MgO cluster before any of the CO molecules.
In summary, the formation of the H-O and Mg-O bonds between the HO molecule and the MgO cluster verifies HO chemisorption on the cluster. The calculated NEB energy profile diagram predicts that the HO molecule dissociation on the MgO cluster is an exothermic process, and the carbonation of MgO is thermodynamically more favourable than its hydration. However, although the calculated for the hydration of the MgO cluster is higher than that for its carbonation, the hydration of the MgO cluster is found to be faster, as confirmed by the calculated and AIMD simulations.
As it is found that hydration of MgO occurs faster than its carbonation, the CO molecule interaction with the hydrated MgO cluster (previously found lowest-energy configuration of hydrated MgO is used) is studied. Several possible configurations of the CO molecule on the hydrated MgO cluster are considered (see Figure S6 in Supporting Information). Figure 3a shows the lowest-energy configuration of the CO molecule on the hydrated MgO cluster, where the O atom of the CO molecule is bonded to the Mg atom of the MgO cluster. The newly formed Mg-O bond has a length of 2.175 Å. The length of the C-O bond (the one closest to the cluster) of the adsorbed CO is elongated to 1.182 Å compared to that of bare CO of 1.174 Å, while another C-O bond of CO shortens to 1.165 Å. The (O–C–O) angle of the CO molecule also decreases from 179.95° to 174.43° upon its adsorption.

Figure 3. (a) The lowest-energy configuration of the physisorbed CO molecule on the hydrated MgO cluster combined with the CDD isosurface plot (0.003 Å). (b) The ELF and (c) DOS and LDOS for the CO–physisorbed hydrated MgO cluster. (d) The lowest-energy configuration of the chemisorbed CO molecule on the hydrated MgO cluster combined with the CDD isosurface plot (0.009 Å). (e) The ELF and (f) DOS and LDOS for the CO–chemisorbed hydrated MgO cluster. (g) The energy barrier and atomic structures corresponding to the minimum energy pathway for the transition of the the CO molecule from physisorbed to chemisorbed states on the hydrated MgO cluster.
The CDD plot in Figure 3a shows that the CO molecule is an acceptor to the hydrated MgO cluster as there is a depletion of the electron on the Mg atom of the cluster and accumulation of electrons on the O atom of the CO molecule. The Bader charge transfer analysis predicts that the amount of the charge transferred from the cluster to the molecule is 0.058 . Importantly, of the CO molecule on the hydrated MgO cluster is -0.53 eV, which is lower than that of the CO molecule on the bare MgO cluster. This suggests stronger bonding of the CO molecule with the hydrated MgO cluster compared to the bare MgO cluster. The ELF plot in Figure 3b demonstrates the electron localization between the O atom of the molecule and the Mg atom of the cluster. It verifies the accumulation of electrons on the O atoms of the CO molecule and suggests that the C–O bonds of the molecule remain covalent. The DOS and LDOS plots in Figure 3c show strong overlapping of HOMO states of the HO molecule and the MgO cluster in the range from -4.2 to -4.8 eV and strong overlapping of LUMO+1 states of the HO molecule and the MgO cluster in the range from 3.4 to 4.5 eV, which confirms a strong bonding between the CO molecule and the hydrated MgO cluster. The conducted AIMD calculations predict the possibility of chemisorption of the CO molecule on the hydrated MgO cluster at room temperature. In chemisorbed state, the O atoms of the CO molecule are bonded to the Mg atoms of the hydrated MgO cluster and the C atom of the CO molecule is bonded to the O atom of the hydrated MgO cluster (see Movie 4 and Figure S7 in Supporting Information). It is observed that the carbonation of bare MgO occurs slower than the carbonation of hydrated due to the formation of groups on the cluster during its hydration, that hinder the carbonation process.
To gain insights into the carbonation mechanism of hydrated , the chemisorption process of on it is considered. The lowest-energy configuration of chemisorbed molecule on the hydrated cluster (for more details see Figure S7 in Supporting Information) is shown in Figure 3d. Here, both O atoms of the molecule form chemical bonds with the Mg atoms of the hydrated cluster. The C–O bonds of the molecule are elongated to 1.269 Å and 1.275 Å (compared to 1.174 Å of the bare molecule) upon it adsorption on the hydrated cluster. The length of newly formed Mg-O bonds is 2.057 Å and 2.025 Å, while the length of the C–O bond formed between the C atom of the molecule and the O atom of the cluster is 1.382 Å. The angle of the adsorbed molecule is found to be 129.16°, which is lower than that of the molecule in its physisorbed state. The CDD plot in Figure 3d shows that the charge is mostly distributed on the molecule and partially on the O atom of the cluster bonded to the C atom of the molecule. The basicity of the hydrated cluster drives the electron transfer from the molecule to the hydrated cluster. According to the Bader charge transfer analysis, the chemisorbed molecule gains 0.086 from the hydrated cluster. Therefore, the amount of the charge transferred from the hydrated cluster to the chemisorbed molecule is higher than that from the hydrated cluster to the physisorbed molecule (see Table S1 Supporting Information). The calculated of -1.55 eV for the molecule chemisorbed on the hydrated cluster is higher than that of the molecule chemisorbed on the bare cluster (-1.05 eV). The ELF plot in Figure 3e depicts electron localizations between the O atoms of the chemisorbed molecule and the Mg atoms of the hydrated cluster and the C atom of the chemisorbed molecule and the O atom of the hydrated cluster, which suggests the existence of the covalent Mg-O and C-O bonds between the cluster and the molecule. Meanwhile, the covalent bonding between the molecule and the cluster remains unchanged. According to DOS and LDOS plots presented in Figure 3f, there is a strong hybridization of HOMO and HOMO-1 states of the hydrated cluster and the chemisorbed molecule. The overlapping of the cluster and the molecule is also observed at -3.8 eV, -4.5 eV and 4.6 eV.
of 0.275 eV (see Table S2 in Supporting Information) for the transition of the molecule from physisorbed state to chemisorbed state on the hydrated cluster is calculated by the NEB approach (see Figure 3g). The transition involves the IM2 stage, where the O atom of the molecule oxidizes the Mg atom of the cluster, which leads to the drop of to 0.153 eV. This triggers an exothermic process of bonding the C and O atoms of the molecule to the hydrated cluster at the FS state via the IM3 (-0.800) state with the released energy of 1.028 eV. According to calculated reaction energies in the carbonation process of bare (-0.617 eV) and hydrated (-1.028 eV), carbonation of the hydrated is thermodynamically more favourable. However, for the transition of from the physisorbed state to the chemisorbed state on hydrated (0.275 eV) is higher than that of on bare (0.234 eV). Therefore, chemisorption on hydrated is kinetically unfavourable. This matches the AIMD simulation results (see Figures S2 and S6 in Supporting Information), where the carbonation of bare is faster than that of the hydrated . Importantly, this verifies the fact that the initial hydration of can hinder its carbonation.[15]
In summary, the chemisorption of the on the cluster is found to be the most energetically favourable. The charge redistribution between the cluster and the molecule during the chemisorption[37, 38] and the comparison of the energy released during carbonation of the bare and the hydrated clusters suggests carbonation of the bare cluster is faster than that of the hydrated cluster, which uncovers the hindrance effect of on the carbonation of .
The observed results are also supported by AIMD simulations (see Movie 4 and Figure S7 in Supporting Information).
Mg(OH) interaction with CO and HO. In RMC reactions, the carbonation of Mg(OH) leads to the production of a range of HMCs.[12, 13] Therefore, the mechanism of the carbonation of Mg(OH) is further studied. For that, several possible configurations of the CO molecule and the Mg(OH) cluster are examined (see Figure S8 in Supporting Information). The most favourable sites for the CO molecule adsorption on Mg(OH) are located at its edges. Figure 4a combines the atomic structure of the lowest-energy configuration and the CDD plot for the CO molecule adsorbed on the Mg(OH) cluster. In that case, the C atom of the CO molecule is located below the O atom at the edge of the Mg(OH) cluster and is bonded to the O atom of the cluster. In the same way, the O atom of the CO molecule is bonded to the Mg atom at the edge of the Mg(OH) cluster and forms the Mg–O bond of a length of 2.069 Å. Upon adsorption, the C–O bonds in the CO molecule elongates from 1.174 Å (bare ) to 1.266 Å, while a newly formed C–O bond between the molecule and has a length of 1.515 Å and changes from 179.95° to 136.88°. The CDD plot in Figure 4a displays the charge transfer from O atoms at the edge of to the molecule. The Bader charge transfer analysis suggests that acts as an acceptor to the cluster, with the charge transfer from the cluster to the molecule of 0.397 (see Table S1 in Supporting Information). This verifies the Lewis basicity of the cluster. According to Table S1 (see Supporting Information), the of on is -0.69 eV.

Figure 4. (a) The atomic structure of the lowest-energy configuration of the molecule on the cluster combined with the CDD isosurface plot ( Å). (b) The ELF and (c) DOS and LDOS for the –adsorbed cluster. (d) The energy barrier and atomic structures corresponding to the minimum energy pathway for the carbonation of the cluster. (e) The atomic structure of the lowest-energy configuration of the molecule on the cluster combined with the CDD isosurface plot ( Å). (f) The ELF and (g) DOS and LDOS for the –adsorbed cluster.
The ELF plot in Figure 4b shows electron localization between the O atom of the molecule and the Mg atom of the cluster, which characterizes electron transfer and strong bonding between the molecule and the edge of the cluster. The covalent bonding within the molecule also remains stable, as predicted by the charge localization on both the C–O bonds of the molecule. The DOS and LDOS plots for the –adsorbed cluster are shown in Figure 4c. The observed strong orbital hybridisation of and at the energy of -1.7 eV and in a range from -2 to -3.7 eV confirms the strong interaction between and proposed by the charge transfer and ELF analysis. Figure 4d depicts the potential energy profile and atomic structures corresponding to the minimum energy pathway for the carbonation of the cluster. It is shown that for the carbonation of is as low as 0.002 eV (TS in Figure 4d), which is equivalent to a spontaneous process at room temperature. To reach the chemisorbed state at FS (-0.303 eV), the molecule passes through the IM2 state (-0.064 eV) where the C atom of the molecule bonds to the O atom of the cluster, and IM3 (-0.256), at which point the O atom of the molecule forms a bond with the Mg atom of the cluster. It is also noted that the carbonation of is a highly exothermic process.
In summary, the elongation of C–O bonds and the decrease of of the molecule, along with the strong charge transfer between the molecule and the cluster, play a dominant role in chemisorption on . Despite the chemisorption of on occurring only at the edges, chemisorption mechanism of for is similar to that for . In both cases, chemisorption of is an exothermic process with low and significant energy release. However, the activation energy for the carbonation of (0.002 eV) is significantly lower than that for (0.049 eV), confirming that carbonation of the is faster than that of the . In turn, the energy released during the carbonation (-0.617 eV) is about 2 times lower than that during the carbonation (-0.303 eV), which suggests that the carbonation of the cluster is more thermodynamically favourable.
is often affected by aqueous environments, therefore, the interaction of the molecule with the cluster can play a key role in HMC formation. From the studied configurations for that interaction of with (see Figure S9 in Supporting Information), the lowest-energy configuration is related to the molecule located at the edge of the cluster. The length of the O–H bond of the bare molecule (1.972 Å) is shortened to 1.020 Å upon the molecule bonding to the cluster, while the O–H bond at the edge of the cluster is elongated from 0.965 Å to 0.984 Å. The CDD plot in Figure 4e shows that the charge is mostly distributed on the molecule and partially at the edge of the cluster. The Bader charge transfer analysis predicts the molecule to be a weak acceptor to the cluster that accumulates 0.044 (see Table S1 in Supporting Information). of the molecule on the cluster is -0.74 eV (see Table S1 in Supporting Information). The ELF plot in Figure 4f shows insignificant electron distributions between the O atom of the molecule and the H atom of the cluster. Meanwhile, low electron density between the H atom of the molecule and the O atom of the cluster indicates weak interaction between them. Moreover, orbital localization between the O–H bonds of the molecule shows that the covalent bonds of the molecule remain stable. The DOS and LDOS plots for the molecule adsorbed on the cluster, shown in Figure 4g, also suggests a weak interaction between the molecule and the cluster at eV, eV, eV, and in ranges from to eV and from to eV.
In summary, it is found that the molecule is located at the edges of the cluster. The calculated low and weak charge transfer between the molecule and the cluster suggest that is physisorbed on . However, it is well-known that the presence of facilitates the formation of HMCs in accessible pores during the carbonation process.[37]
To investigate a mechanism of reaction of nesquehonite formation (), at the first step, the simultaneous interaction of the carbonated cluster and the molecule () is considered. At the second step, one more molecule is introduced to the system studied at the first step (). Although the natural process of the nesquehonite formation also includes nucleation and growth from species in solution, the studied reaction will still help to understand possible nucleation or growth paths of nesquehonite. At the first step, various configurations of one molecule (see Figure S10 in Supporting Information) on the carbonated cluster are considered. At the lowest-energy configuration, the molecule is bonded to the edge of the cluster. The length of the O– H bonds increases to 0.970 Å and 1.022 Å compared to these of the bare molecule (0.936 Å). The distance between the H atom of the molecule and the O atom of the cluster is 1.620 Å, while the distance between the O atom of the and the H atom of the cluster is 1.957 Å. According to Table S1 (see Supporting Information), of the molecule on the cluster is -0.86 eV. The CDD plot in Figure 5a shows that there is a depletion of electrons at the edge O atoms of the cluster and charge accumulation at the H atoms of the molecule. The Bader charge transfer analysis shows that the molecule gains 0.046 from the cluster which confirms that is a weak acceptor to (see Table S1 in Supporting Information). Further, the ELF plot in Figure 5b shows is physisorbed on , as there is no electron density localization between the cluster and the molecule, while the H-O bonds of remain their covalent nature. Figure 5c represents the DOS and LDOS plots for the molecule adsorption on the carbonated cluster. Small overlapping of states of the molecule and the carbonated cluster is observed in the range from -3.0 to -3.7 eV, verifying weak interaction between them.

Figure 5. (a) The lowest-energy configuration of the molecule on the carbonated cluster with the CDD isosurface plot (0.001 Å). (b) The ELF and (c) DOS and LDOS for molecules on the carbonated cluster. (d) The lowest-energy structure of the molecules on the carbonated cluster combined with the CDD plot (0.001 Å). (e) The ELF and (f) DOS and LDOS for the molecule on the carbonated cluster. (g) Initial and (h) final (chemisorbed state) configurations of and molecules on the cluster. (i) Initial and (h) final configurations of and molecules on the carbonated cluster.
Further, at the second step, the second molecule is introduced to the + + system obtained at the first step (see Figure S11 in Supporting Information). The lowest energy configuration of the molecule on the + + system is shown in Figure 5d, where the second molecule is also located at the edge of the carbonated cluster. The length of the H-O bonds of the bare molecule is 0.971 Å, while they slightly elongate to 0.975 Å and 0.973 Å after adsorption. The distance between the O atom of the molecule and the Mg atom of the cluster is 2.232 Å. According to Table S1 (see Supporting Information) of the molecule on the + + system is -0.46 eV. The CDD plot in Figure 5d displays the depletion of electrons at O atoms located at the edge of the cluster and charge accumulation at the H atoms of the molecule. According to the Bader charge transfer analysis (see Table S1 in Supporting Information) the molecule is a weak acceptor to the cluster with the charge transfer of 0.037 from the cluster to the molecule. The ELF plot in Figure 5e shows no election density localization between the second molecule and the + + system, which means there is a weak interaction between them. The DOS and LDOS plots in Figure 5f also display a weak interaction of the molecule and the cluster at the range from -2.8 to -3.5 eV.
AIMD simulations are used to investigate the reaction for the formation of HMCs via the interaction of the and molecules with the cluster (see Movie 5 and Figure 5g and Figure 5h in Supporting Information,). As it is shown, the and molecules are bonded at the edges of the cluster, which suggests that the formation of HMCs starts at the edges of . Further, AIMD simulations are conducted to consider the effect of large amount of and molecules on the formation of HMCs (see Movie 6 in Supporting Information). For that, two and one molecules are added to the previously considered + + system. As shown in Figure 5h, the first molecule is able to carbonate the cluster. However, after the bonding of the first molecule to the cluster, the second molecule is unable to bind to the carbonated cluster (Figure 5i and Figure 5j). This suggests that the formation of an early layer of carbonates in RMC-based concrete formulations may limit the continuation of carbonation by forming a physical barrier that prohibits further interaction between and . These limitations in carbonation of can cause large amounts of unreacted crystals leading to relatively low strength and porous microstructures.[15, 43] Although the presence of molecules provides the medium for carbonation and further transformation of into HMCs and is required for the continuous formation of HMCs[44], according to the AIMD simulations, excessive hinders penetration to the surface. Therefore, to maintain diffusion for carbonation of , the amount of should be properly controlled.[40] The predicted results of passivation with the formation of the barrier of carbonates and hindrance effect on carbonation of correspond to the carbonation mechanisms of portlandite.[45]
As the adsorption behaviour of molecules on the clusters may be different from that on the bulk materials. Further, the interaction of the and molecules with clusters and with the bulk and is compared. Figure 6a and Figure 6b represent the lowest-energy configuration of the and molecules on . Figure 6a shows the O atom of molecule is located above Mg atom of . The length of C–O bonds in the molecule elongates from 1.174 Å (bare ) to 1.182 Å and 1.175 Å and decreases from 179.95° to 176.81°. The calculated for on the surface is -0.34 eV (see Table S3 in Supporting Information). This indicates weak adsorption of on the bulk compared to the physisorbed- on the cluster ( = -0.42 eV). According to Figure 6b, O atom of molecule is located above Mg atom of . The length of the H–O bonds of the molecule, elongates from 0.972 Å (bare ) to 0.983 Å and 0.977 Å. eV of the molecule on (see Table S3 in Supporting Information) is found to be lower than that of the molecule (-0.95 eV) on the cluster. The length of the bond formed between the O atom of the molecule and the Mg atom at the surface is 2.239 Å, which is longer than the bond formed between the O atom of the molecule and the Mg atom of the cluster (2.085 Å). Therefore, for both and molecules their adsorption and possible dissociation at the edges or defective surfaces of the crystal, presented here via clusters, is more favourable. This result well matches the previously reported observation on weak adsorption of the molecule on the surface.[24]

Figure 6. The side and top views of the lowest-energy configuration of (a) and (b) molecules on the surface. The side and top views of the lowest-energy configuration of (c) and (d) molecules on the surface.
Figures 6c and d show the lowest-energy configurations of the and molecules on the surface. Figure 6c indicates the location of the C atom of the molecule is located above the Mg-O bond of the surface. The C–O bonds in the molecule elongates from 1.174 Å (bare ) to 1.177 Å and 1.178 Å, and changes from 179.95° to 179.00°. of the molecule on the surface is as low as -0.25 eV, which is significantly lower than that of the molecule on the cluster (-0.69 eV) (see Table S3 in Supporting Information). Figure 6d depicts interaction of the H atom of molecule with the O atom of the surface. The length of the H–O bond of the molecule near to the surface, elongates from 0.972 Å (bare ) to 0.994 Å, while another O-H bond is shortened to 0.952 Å. of molecule on the surface is found to be -0.37 eV, which is lower than that of the molecule on cluster (-0.74 eV) (see Table S3 in Supporting Information). In addition, the distance between the molecule and the surface of 2.017 Å, is longer than that between the molecule and the cluster (1.957 Å). Similar to the case of , the lower of the and molecules on the cluster, compared to that on the surface, suggests stronger interaction of these molecules with the edge and/or defect-containing surface of crystal.
Conclusions
In the present study, the mechanism of potential reactions on and during HMC synthesis is investigated by DFT-based calculations. The results show that despite the energy barrier for the molecule adsorption on MgO is lower than that for the molecule adsorption on MgO, the hydration of MgO is faster, due to the difference in the frequency of and molecules collisions with MgO. In addition, it is found that adsorption of on hydrated MgO is slower than that on bare MgO, which means that the presence of molecules (moisture environment) can hinder MgO carbonation. In turn, the carbonation of is found to be significantly faster than that of MgO. It should be noted, that both hydration and carbonation of take place at the edges. In addition, a weaker interaction of the and molecules with the MgO and surfaces compared to the edge and/or defect-containing surfaces (clusters) is found. Importantly, two limiting factors of the HMCs formation reaction are found: i) surface passivation of upon its initial carbonation and ii) surface covering of by molecules, which inhibits the carbonation on .
Acknowledgements
M.G.G., H.N. and P.K. are grateful for the support of the Academy of Finland grant CCC (329477) and the University of Oulu and the Academy of Finland Profi5 funding (326291). K.A.A. and W.C acknowledge funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No. 101002219). H.M. would like to acknowledge funding from “Departamento de Educación, Política Lingüística y Cultura del Gobierno Vasco” (Grant No. IT1358-22). The authors wish to acknowledge CSC–IT Center for Science, Finland, for providing computational resources.
References
- [1]Kulp, S. A.; Strauss, B. H. New Elevation Data Triple Estimates of Global Vulnerability to Sea-Level Rise and Coastal Flooding. Nat. Commun. 2019, 10 (1), 1–12.DOI
- [2]Olivier, J. G. J.; Peters, J. A. H. W.; Janssens-Maenhout, G. Trends in Global CO2 Emissions 2012 Report. 2012.DOI
- [3]Van Oss, H. G.; Padovani, A. C. Cement Manufacture and the Environment: Part I: Chemistry and Technology. J. Ind. Ecol. 2002, 6 (1), 89–105.DOI
- [4]Birchal, V. S. S.; Rocha, S. D. F.; Ciminelli, V. S. T. The Effect of Magnesite Calcination Conditions on Magnesia Hydration. Miner. Eng. 2000, 13, 1629–1633.DOI
- [5]Walling, S. A.; Provis, J. L. Magnesia-Based Cements: A Journey of 150 Years, and Cements for the Future? Chem. Rev. 2016, 116 (7), 4170–4204.DOI
- [6]Gartner, E.; Sui, T. Alternative Cement Clinkers. Cem. Concr. Res. 2018, 114, 27–39.DOI
- [7]Ruan, S.; Unluer, C. Comparative Life Cycle Assessment of Reactive MgO and Portland Cement Production. J. Clean. Prod. 2016, 137, 258–273.DOI
- [8]Zhongming, Z.; Linong, L.; Wangqiang, Z.; Wei, L. AR6 Climate Change 2021: The Physical Science Basis. 2021.
- [9]Unluer, C.; Al-Tabbaa, A. Impact of Hydrated Magnesium Carbonate Additives on the Carbonation of Reactive MgO Cements. Cem. Concr. Res. 2013, 54, 87–97.DOI
- [10]Li, X. Mechanical Properties and Durability Performance of Reactive Magnesia Cement Concrete. University of Cambridge 2013.
- [11]Ma, S.; Akca, A. H.; Esposito, D.; Kawashima, S. Influence of Aqueous Carbonate Species on Hydration and Carbonation of Reactive MgO Cement. J. CO2 Util. 2020, 41, 101260.DOI
- [12]Unluer, C.; Al-Tabbaa, A. Enhancing the Carbonation of MgO Cement Porous Blocks through Improved Curing Conditions. Cem. Concr. Res. 2014, 59, 55–65.DOI
- [13]Thomas, J. J.; Musso, S.; Prestini, I. Kinetics and Activation Energy of Magnesium Oxide Hydration. J. Am. Ceram. Soc. 2014, 97 (1), 275–282.
- [14]Matabola, K. P.; van der Merwe, E. M.; Strydom, C. A.; Labuschagne, F. J. W. The Influence of Hydrating Agents on the Hydration of Industrial Magnesium Oxide. J. Chem. Technol. Biotechnol. 2010, 85 (12), 1569–1574.
- [15]Dung, N. T.; Unluer, C. Development of MgO Concrete with Enhanced Hydration and Carbonation Mechanisms. Cem. Concr. Res. 2018, 103, 160–169.DOI
- [16]Zhao, J.; Huang, X.; Shi, R.; Tang, L.; Su, Y.; Sai, L. Ab Initio Global Optimization of Clusters. Chem. Model. 2015, 12, 249–292.DOI
- [17]Kistanov, A. A.; Shcherbinin, S. A.; Ustiuzhanina, S. V; Huttula, M.; Cao, W.; Nikitenko, V. R.; Prezhdo, O. V. First-Principles Prediction of Two-Dimensional B3C2P3 and B2C4P2: Structural Stability, Fundamental Properties, and Renewable Energy Applications. J. Phys. Chem. Lett. 2021, 12 (13), 3436–3442.DOI
- [18]Liu, B.; Zhou, K. Recent Progress on Graphene-Analogous 2D Nanomaterials: Properties, Modeling and Applications. Prog. Mater. Sci. 2019, 100, 99–169.DOI
- [19]Alessio, M.; Usvyat, D.; Sauer, J. Chemically Accurate Adsorption Energies: CO and H2O on the MgO (001) Surface. J. Chem. Theory Comput. 2018, 15 (2), 1329–1344.DOI
- [20]Fan, H.-X.; Cui, T.-Y.; Rajendran, A.; Yang, Q.; Feng, J.; Yue, X.-P.; Li, W.-Y. Comparative Study on the Activities of Different MgO Surfaces in CO2 Activation and Hydrogenation. Catal. Today 2020, 356, 535-543.DOI
- [21]Huang, J.; Li, X.; Wang, X.; Fang, X.; Wang, H.; Xu, X. New Insights into CO2 Methanation Mechanisms on Ni/MgO Catalysts by DFT Calculations: Elucidating Ni and MgO Roles and Support Effects. J. CO2 Util. 2019, 33, 55–63.DOI
- [22]Jang, J. M.; Kang, S. G. Understanding CO2 Adsorption on a M1 (M2)-Promoted (Doped) MgO–CaO (100) Surface (M1= Li, Na, K, and Rb, M2= Sr): A DFT Theoretical Study. ACS Sustain. Chem. Eng. 2019, 7 (20), 16979–16984.
- [23]Cornu, D.; Guesmi, H.; Krafft, J.-M.; Lauron-Pernot, H. Lewis Acido-Basic Interactions between CO2 and MgO Surface: DFT and DRIFT Approaches. J. Phys. Chem. C 2012, 116 (11), 6645–6654.DOI
- [24]Wu, S.; Tan, B. T.; Senevirathna, H. L.; Wu, P. Polarization of CO2 for Improved CO2 Adsorption by MgO and Mg (OH)2. Appl. Surf. Sci. 2021, 562, 150-187.DOI
- [25]Dung, N. T.; Lesimple, A.; Hay, R.; Celik, K.; Unluer, C. Formation of Carbonate Phases and Their Effect on the Performance of Reactive MgO Cement Formulations. Cem. Concr. Res. 2019, 125, 105894.DOI
- [26]Hopkinson, L.; Kristova, P.; Rutt, K.; Cressey, G. Phase Transitions in the System MgO–CO2–H2O during CO2 Degassing of Mg-Bearing Solutions. Geochim. Cosmochim. Acta 2012, 76, 1–13.DOI
- [27]Castleman, A. W.; Bowen, Kh. Clusters: Structure, Energetics, and Dynamics of Intermediate States of Matter. J. Phys. Chem. 1996, 100 (31), 12911–12944.DOI
- [28]Ohlin, C. A.; Villa, E. M.; Rustad, J. R.; Casey, W. H. Dissolution of Insulating Oxide Materials at the Molecular Scale. Nat. Mater. 2010, 9 (1), 11–19.DOI
- [29]Kresse, G.; Furthmüller, Efficient Iterative Schemes For Ab Initio Total-Energy Calculations Using a Plane-Wave Basis Set. J. Phys. Rev. B: Condens. Matter Mater. Phys. 1996, 54, 11169-11186.pubmed.ncbi.nlm.nih.gov/9984901
- [30]Blöchl, P. E. Projector Augmented-Wave Method. Phys. Rev. B 1994, 50 (24), 17953.pubmed.ncbi.nlm.nih.gov/9976227
- [31]Perdew, J. P.; Burke, K.; Ernzerhof, M. Generalized Gradient Approximation Made Simple. Phys. Rev. Lett. 1996, 77 (18), 3865.pubmed.ncbi.nlm.nih.gov/10062328
- [32]Zhang, S.; Zhang, Y.; Huang, S.; Liu, H.; Wang, P.; Tian, H. Theoretical Investigation of Growth, Stability, and Electronic Properties of Beaded ZnO Nanoclusters. J. Mater. Chem. 2011, 21 (42), 16905–16910.DOI
- [33]Chen, M.; Dixon, D. A. Structure and Stability of Hydrolysis Reaction Products of MgO Nanoparticles Leading to the Formation of Brucite. J. Phys. Chem. C 2017, 121 (39), 21750–21762.DOI
- [34]Zhang, D.; Sun, Y.; Chen, L.; Zhang, S.; Pan, N. Influence of Fabric Structure and Thickness on the Ballistic Impact Behavior of Ultrahigh Molecular Weight Polyethylene Composite Laminate. Mater. Des. 2014, 54, 315–322.
- [35]Becke, A. D. Density-Functional Exchange-Energy Approximation with Correct Asymptotic Behavior. Phys. Rev. A 1988, 38 (6), 3098.pubmed.ncbi.nlm.nih.gov/9900728
- [36]Niu, J.; Wang, Y.; Qi, Y.; Dam, A. H.; Wang, H.; Zhu, Y.-A.; Holmen, A.; Ran, J.; Chen, D. New Mechanism Insights into Methane Steam Reforming on Pt/Ni from DFT and Experimental Kinetic Study. Fuel 2020, 266, 117143.DOI
- [37]Richard F. W. Bader. Bader Atoms in Molecules – A Quantum Theory; Oxford University Press: New York, 1990.
- [38]Laidler, K. J. Chemical Kinetics; Harper & Row: New York, 1987.
- [39]Kistanov, A. A.; Cai, Y.; Zhou, K.; Srikanth, N.; Dmitriev, S. V; Zhang, Y.-W. Exploring the Charge Localization and Band Gap Opening of Borophene: A First-Principles Study. Nanoscale 2018, 10 (3), 1403–1410.DOI
- [40]Henkelman, G.; Uberuaga, B. P.; Jónsson, H. A Climbing Image Nudged Elastic Band Method for Finding Saddle Points and Minimum Energy Paths. J. Chem. Phys. 2000, 113 (22), 9901–9904.DOI
- [41]Nosé, S. A Unified Formulation of the Constant Temperature Molecular Dynamics Methods. J. Chem. Phys. 1984, 81 (1), 511–519.DOI
- [42]Jensen, M. B.; Pettersson, L. G. M.; Swang, O.; Olsbye, U. CO2 Sorption on MgO and CaO Surfaces: A Comparative Quantum Chemical Cluster Study. J. Phys. Chem. B 2005, 109 (35), 16774–16781.pubmed.ncbi.nlm.nih.gov/16853136
- [43]Dung, N. T.; Uhluer, C. Performance of Reactive MgO Concrete under Increased CO2 Dissolution. Cem. Concr. Res. 2019, 118, 92–101.DOI
- [44]Unluer, C. Carbon Dioxide Sequestration in Magnesium-Based Binders. Woodhead Publishing. 2018, 129–173.DOI
- [45]Mutisya, S. M.; Kalinichev, A. G. Carbonation Reaction Mechanisms of Portlandite Predicted from Enhanced Ab Initio Molecular Dynamics Simulations. Minerals 2021, 11 (5), 509.DOI