betaFeedback

WorksPhysics and Astronomy

Robust Microwave-Optical Photon Conversion Using Cavity Modes Strongly Hybridized with a Color Center Ensemble

Abstract

A microwave-optical photon converter with high efficiency (>50>50 %) and low added noise (≪1\ll 1 photon) could enable the creation of scalable quantum networks where quantum information is distributed optically and processed in the microwave regime. However, integrated converters demonstrated to date lack sufficient co-operativity or are too lossy to provide the required performance. Here we propose a bi-directional microwave-optical converter employing an ensemble of spin-bearing color centers hosted within a high-Q Si photonic resonator and coupled magnetically to a high-Q superconducting microwave resonator. We develop a theory for microwave-optical conversion when the ensemble of centers is strongly hybridized with one or both cavities, and find a counterintuitive operating point where microwave and optical photons are tuned to bare center/cavity resonances. Compared to the perturbative coupling regime, we find a substantially enhanced nonlinearity, making it possible to obtain the required co-operativity with reduced pump- and center-induced losses, and improved robustness to optical inhomogeneous broadening. Taking color center and optical pump-induced losses into account in both the Si photonic and superconducting resonators, we find that ∼95\sim 95 % total efficiency and added noise ≪1\ll 1 quanta is possible at low (μμW) pump powers for both Er- and T-centers in Si. Our results open new pathways towards quantum networks using microwave-optical converters.

Introduction

Distributing quantum information across a quantum network [1, 2] where nodes operate in the microwave domain [3, 4, 5, 6], will inevitably require a coherent interface between microwave photons and optical photons. Recently, several coherent microwave-optical converter (MOC) devices have been proposed to build quantum networks [7, 8, 9, 10, 11, 12, 13], and MOCs relying on electro-optical [14, 15, 16, 17, 18, 19, 20, 21, 22], opto-electro-mechanical [23, 24, 25, 26, 27, 28], and magneto-optical [29, 30, 31, 32, 33, 34, 35, 36, 37] nonlinearities have been demonstrated. On-chip MOCs are particularly appealing due to their compact size, potential for low pump powers, potential for integration.

Despite significant experimental progress [14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35, 36, 37], integrated MOCs demonstrated to date do not meet efficiency (η>50%\eta> 50\%), and added noise (Nadd≪1N_{\mathrm{add}} \ll1) criteria for a quantum network [1]. Both figures of merit are degraded by loss and/or excitation within the microwave and optical subsystems and in nonlinear media providing the conversion [38]. Losses often arise from strong optical pumps needed to compensate weak nonlinearities, while noise can be added from excitations in strongly nonlinear media that are difficult to cool [23, 26]. Significant improvements in converter performance (ideally approaching 100 % efficiency) from stronger nonlinearities, reduced loss and reduced noise are needed to unlock the potential of MOCs for quantum networks.

Spin-bearing, optically active centers in solids are a promising system for high-efficiency, low-noise conversion via the magnetic coupling of their spin transitions to microwave photons and coupling of their orbital transitions to optical photons[8, 13, 33, 34, 35, 36, 37, 39, 40]. To date, the regime of large ensemble-cavity detuning has been considered theoretically: cavity-enhanced MOC with color center ensembles [8, 13], and rare-earth ion-based MOC devices operating in this regime have reached ∼1%\sim1\% efficiencies [37, 41]. Greater efficiency could be obtained through increased center-cavity couplings gg and center number NAN_{\mathrm{A}}, and decreased detuning δ\delta and cavity loss κ\kappa [8]. Each of these changes brings the system closer the strong ensemble-cavity coupling regime, 2gNA≳δ/2,κ/22g\sqrt{N_{\mathrm{A}}} \gtrsim\delta/2,\kappa/2, for both the optical and microwave cavities, but this regime has yet to be described theoretically.

Here we generalize the theory of MOC to the case where one or both of the microwave and optical cavities is strongly coupled to the center ensemble, for both homogeneously and inhomogeneously broadened ensembles, including dressing by the optical pump. We find that high-efficiency conversion is possible when the microwave and optical signal photons are nearly resonant with states that resemble the vacuum Rabi-split eigenstates of the isolated microwave and optical subsystems. Counterintuitively, we also find that near-unity conversion efficiency is possible when the optical and microwave signal photons are close to the bare center/cavity resonances for strong ensemble-cavity coupling. This strong coupling regime allows us to maintain high co-operativity and conversion efficiency at lower pump power, and benefits from pump dressing to suppress negative effects of inhomogeneous broadening while retaining low center-induced losses.

To showcase the potential of microwave-optical conversion in the strong ensemble-cavity coupling regime, we propose a device consisting of a high-QQ Si photonic racetrack resonator containing color centers and a high-QQ superconducting resonator. We predict the MOC efficiency and noise for optical and microwave photons tuned to the bare center and cavity resonances, considering the following nonidealities: (1) color center-induced loss and dispersion, (2) two-photon and free-carrier absorption loss in Si, (3) optical loss and optically-induced microwave loss to the superconducting resonator, and (4) realistic color center inhomogeneous broadening. The proposed device benefits from strong two-dimensional optical confinement in Si resonators to limit losses due to superconducting quasiparticle generation. The superconducting resonator is loaded with an interdigitated capacitor [42], which serves to match its length to the photonic resonator and reduce its impedance, both of which enhance nonlinearity. Benefiting from long spin lifetimes and narrow spin linewidths in Si [44, 45, 46, 47] [43], we find a concentration of ∼1016\sim10^{16} cm−3^{-3} T-centers (∼1017\sim10^{17} Er-centers) [46, 47], with optical inhomogeneous broadening up to 1 GHz (similar to reported values) provides near-unity efficiency (∼95%\sim95\%) with added noise ≪1\ll1 photon at pump powers ≲1\lesssim1 µW.

Concept and Model

The proposed MOC (Figure 1(a)) employs three-wave mixing (3WM) between a microwave signal, optical signal, and optical pump having photon frequencies ωμ\omega_\mu, ωo\omega_o, and ωp=ωo−ωμ\omega_p = \omega_o - \omega_\mu, respectively. The 3WM process is resonantly enhanced by microwave cavity, optical cavity, and optical pump cavity modes with bare frequencies ωc\omega_c, ωa\omega_a, and ωb\omega_b, respectively [48, 49]. The three cavity modes overlap spatially inside a medium hosting an ensemble of color centers with microwave and optical transition frequencies ω12\omega_{12}, ω13\omega_{13}, and ω23\omega_{23}, which provides the 3WM nonlinearity.

Figure 1. Si-integrated microwave-optical converter. (a) Schematic of color centers in Si coupled optically to a Si cavity with signal and pump resonances and magnetically to a superconducting microwave cavity. The conversion between the microwave and optical photons at ωμ\omega_\mu and ωo\omega_o respectively is induced by an optical pump at ωp\omega_p. (b) Energy diagram for color center ensemble and cavity resonances ωa\omega_a and ωc\omega_c for (left) no ensemble-cavity coupling and (right) ensemble-cavity coupled system at zero detunings with pump off. The color center ensemble is assumed to be homogeneously broadened in the diagram. (c) Device schematic comprising an optical racetrack cavity and a distributed superconducting microwave cavity loaded with an interdigitated capacitor, with applied magnetic field. (d) Cross-section view of the device at the dashed line in the main panel.

The Hamiltonian describing the system in the frame rotating at the resonant frequencies ωc\omega_c and ωa\omega_a is [8, 35]

H^/ℏ=∑k(δ13,kσ^33,k+δ12,kσ^22,k)+∑k(g13,kσ^31,ka^+g12,kσ^21,kc^)+h.c.+∑k(Ωp,ke−iΔtσ^32,k)+h.c.(1)\hat{H}/\hbar= \sum_k \left(\delta_{13,k}\hat{\sigma}_{33,k}+\delta_{12,k}\hat{\sigma}_{22,k}\right) + \sum_k \left(g_{13,k}\hat{\sigma}_{31,k}\hat{a}+g_{12,k}\hat{\sigma}_{21,k}\hat{c}\right)+\mathrm{h.c.} + \sum_k \left(\Omega_{p,k}e^{-i\Delta t}\hat{\sigma}_{32,k}\right)+\mathrm{h.c.} \tag*{(1)}

where σ^ij,k\hat{\sigma}_{ij,k} is a Pauli operator for the kkth color center, with i,j∈{1,2,3}i,j \in\{1,2,3\}, a^\hat{a} (c^\hat{c}) is the annihilation operator of the optical (microwave) signal photon. Here, δ13,k=ω13,k−ωa\delta_{13,k} = \omega_{13,k} - \omega_a and δ12,k=ω12,k−ωc\delta_{12,k} = \omega_{12,k} - \omega_c are the detunings of the orbital and spin transitions of the kkth center from the bare optical and microwave cavity frequencies, respectively, which may vary from center to center. Additionally, g13,kg_{13,k}, g12,kg_{12,k} are the optical and microwave center-cavity coupling rates, and Ωp,k\Omega_{p,k} is the pump Rabi frequency for the ∣2⟩↔∣3⟩\lvert2\rangle\leftrightarrow\lvert3\rangle optical transition (Figure 1(b)), which may vary between centers due to spatial inhomogeneity of the cavity modes. Δ=ωp−(ωa−ωc)\Delta= \omega_p - (\omega_a - \omega_c) is the shift of the pump frequency from the difference between the bare optical and microwave cavity frequencies.

We solve the Heisenberg equations of motion for Eq. (1) with single-mode optical and microwave reservoir channels and center dampings. The conversion efficiency is predicted from input-output theory, taking into account internal loss and port reflection. Our treatment differs from past works [8, 13, 35] by allowing arbitrary center-cavity detunings and time-varying cavity fields {a^,c^}\{\hat{a}, \hat{c}\} and color center polarizations {σ^13,σ^12}\{\hat{\sigma}_{13}, \hat{\sigma}_{12}\} relevant in the hybrid ensemble-cavity regime. In our analytic treatment we neglect upper state populations and nonlinear operator terms in the Heisenberg equations of motion [8, 13], and validate these assumptions using a numerical solution presented in the Supplementary Information.

We find that the bidirectional total conversion efficiency is given by

η=κaexκcex∣ξac∣2∣ξac2+[κa/2−i(ω+Δ−ξa)][κc/2−i(ω−ξc)]∣2(2)\eta= \frac{\kappa_a^{\mathrm{ex}}\kappa_c^{\mathrm{ex}}\lvert\xi_{ac}\rvert^2}{\left\lvert\xi_{ac}^2 + [\kappa_a/2 - i(\omega+ \Delta- \xi_a)][\kappa_c/2 - i(\omega- \xi_c)]\right\rvert^2} \tag*{(2)}

where κa/cex\kappa_{a/c}^{\mathrm{ex}} (κa/c≥κa/cex\kappa_{a/c} \ge\kappa_{a/c}^{\mathrm{ex}}) is the coupling (total) loss of the mode a/ca/c, not including color center losses. The center losses depend on the center relaxation rates γ13,k\gamma_{13,k} and γ12,k\gamma_{12,k} for optical and microwave excitations. Furthermore,

ξa=∑k=1NAg13,k2(ω−Δ12,k)(ω+Δ−Δ13,k)(ω−Δ12,k)−Ωp,k2,(3)\xi_a = \sum_{k=1}^{N_A} \frac{g_{13,k}^2(\omega- \Delta_{12,k})}{(\omega+ \Delta- \Delta_{13,k})(\omega- \Delta_{12,k}) - \Omega_{p,k}^2}, \tag*{(3)}
ξc=∑k=1NAg12,k2(ω+Δ−Δ13,k)(ω+Δ−Δ13,k)(ω−Δ12,k)−Ωp,k2,(4)\xi_c = \sum_{k=1}^{N_A} \frac{g_{12,k}^2(\omega+ \Delta- \Delta_{13,k})}{(\omega+ \Delta- \Delta_{13,k})(\omega- \Delta_{12,k}) - \Omega_{p,k}^2}, \tag*{(4)}
ξac=∑k=1NAg12,kg13,kΩp,k(ω+Δ−Δ13,k)(ω−Δ12,k)−Ωp,k2,(5)\xi_{ac} = \sum_{k=1}^{N_A} \frac{g_{12,k}g_{13,k}\Omega_{p,k}}{(\omega+ \Delta- \Delta_{13,k})(\omega- \Delta_{12,k}) - \Omega_{p,k}^2}, \tag*{(5)}

where ω=ωμ−ωc\omega= \omega_\mu- \omega_c and Δ13,k=δ13,k−iγ13,k/2\Delta_{13,k} = \delta_{13,k} - i\gamma_{13,k}/2 and Δ12,k=δ12,k−iγ12,k/2\Delta_{12,k} = \delta_{12,k} - i\gamma_{12,k}/2 are the complex optical and microwave cavity-center detunings.

Under the assumption that the dominant source of added noise is thermal noise in the microwave cavity, the input-referred added noise for microwave-optical and optical-microwave conversion are given respectively by

NMO=κcinκcexNth,(6)N_{\mathrm{MO}} = \frac{\kappa_c^{\mathrm{in}}}{\kappa_c^{\mathrm{ex}}}N_{\mathrm{th}}, \tag*{(6)}
NOM=∣κa/2−i(ω+Δ−ξa)∣2∣ξac∣2κcinκaexNth,(7)N_{\mathrm{OM}} = \frac{\left\lvert\kappa_a/2 - i(\omega+ \Delta- \xi_a)\right\rvert^2}{\lvert\xi_{ac}\rvert^2}\frac{\kappa_c^{\mathrm{in}}}{\kappa_a^{\mathrm{ex}}}N_{\mathrm{th}}, \tag*{(7)}

where Nth=[exp⁡(ℏωc/kBT)−1]−1N_{\mathrm{th}} = [\exp(\hbar\omega_c/k_B T) - 1]^{-1} is the microwave thermal noise population, and κcin\kappa_c^{\mathrm{in}} is the microwave cavity intrinsic loss (see Supplementary Information).

Analysis and Discussion

Here we discuss the hybrid ensemble-cavity converter and its performance. First, we use our model to quantify device performance as a function of the cavity and photon frequencies (relative to centers), pump strength, color center density, vacuum Rabi coupling, and external coupling κex\kappa^{\mathrm{ex}}, considering only color center loss. Next, we show that evanescent optical confinement in the Si waveguide (Figure 1(d)) enables exponential suppression of pump photon loss to the superconductor with only small changes to internal conversion efficiency, and calculate pump-dependent intrinsic nonlinear losses in Si, and losses in the optical and microwave modes due to optically generated quasiparticles in the superconducting cavity. Finally, we predict efficiency and added noise for both T-centers and Er-centers, considering all losses and inhomogeneous broadening.

Efficiency and center-induced losses

In this section we calculate conversion efficiency using our model, considering color center absorption/relaxation as the only source of loss. Three categories of model parameters are considered; (A) the center-cavity detunings δ13/12\delta_{13/12} and photon-cavity detunings ω\omega and Δ\Delta, (B) the color center number NAN_A, the cavities external coupling rates κa/cex\kappa_{a/c}^{\mathrm{ex}}, and the number of pump photons NpN_p, which have practical limits, and (C) color center and material properties (e.g. dipole moments, decay rates, intrinsic cavity losses, inhomogeneous distributions, etc.) For simplicity, we limit calculations in this section to homogeneously broadened ensembles, though we qualitatively discuss inhomogeneous broadening. Calculations with all loss mechanisms and inhomogeneous broadening are presented in Section III C. For simplicity, we assume spatially uniform bosonic fields and drop kk subscripts on γij\gamma_{ij}, gijg_{ij}, and Ωp\Omega_p. We consider δ12=δ13=0\delta_{12} = \delta_{13} = 0, opposite from the condition δ12/13≫g12/13NA\delta_{12/13} \gg g_{12/13}\sqrt{N_A} for weak hybridization [8, 13].

Homogeneous Limit: Examining Eq. (2) with centers and cavities on resonance (δ12=δ13=0\delta_{12} = \delta_{13} = 0), where previous treatments do not apply, reveals that unity efficiency is obtained for optical and microwave photon frequencies defined by the intersection of optical dispersion contours ω+Δ−Re⁡{ξa}=0\omega+ \Delta- \operatorname{Re}\{\xi_a\} = 0 (Condition (i)) and microwave dispersion contours ω−Re⁡{ξc}=0\omega- \operatorname{Re}\{\xi_c\} = 0 (condition (ii)), when a matching condition C=4∣ξac∣2/κaκc=1C = 4\lvert\xi_{ac}\rvert^2/\kappa_a\kappa_c = 1 for the magneto-optic cooperativity CC is satisfied. The optical and microwave contours and their five intersection points are shown in Figure 2(a) for the parameters in Table I that we consider for T-centers. For large ∣ω∣|\omega| (∣Δ∣|\Delta|), the microwave (optical) dispersion contours approach lines representing vacuum Rabi-split states of the microwave (optical) subsystems in the absence of a pump, with energies

Figure 2. Conversion efficiency spectra at zero center-cavity detunings (δ13=δ12=0\delta_{13}=\delta_{12}=0). (a) Contour lines of ω+Δ−Re⁡{ξa}=0\omega+\Delta-\operatorname{Re}\{\xi_a\}=0 (blue) and ω−Re⁡{ξc}=0\omega-\operatorname{Re}\{\xi_c\}=0 (green) at the T-center parameters from Table I. The four red crosses denote the positions of the near-resonance intersection points of the blue and green lines, while the red circle denotes the fifth intersection point at the origin arising from the nonlinear coupling between the microwave and optical systems at finite Ωp\Omega_p. (b) Conversion efficiency spectrum for the T-center parameters from Table I except for κa=0.25\kappa_a=0.25 GHz. The red lines are the contour lines of the matching condition 4∣ξac∣2=κaκc4|\xi_{ac}|^2=\kappa_a\kappa_c. The red crosses and circle denote the same points as in (a). (c) Same as panel (b) but with κa=2\kappa_a=2 GHz, such that matching is obtained at ω=Δ=0\omega=\Delta=0.

ω=±NAg12(ω+Δ=±NAg13).\omega= \pm\sqrt{N_{\mathrm{A}}}g_{12}\quad(\omega+\Delta= \pm\sqrt{N_{\mathrm{A}}}g_{13}).

More practical conditions for high efficiency that take into account cavity-reservoir coupling and center loss are ∣ω+Δ−ξa∣≪κa|\omega+\Delta-\xi_a|\ll\kappa_a and ∣ω−ξc∣≪κc|\omega-\xi_c|\ll\kappa_c.

The conversion efficiency is plotted in Figure 2(b) for the same parameters used in Figure 2(a). Cavity couplings are given in Table I. From Figure 2(b), we see that the efficiency is highest at the intersections of the optical contour and the matching contour. This is because the microwave reservoir coupling κc\kappa_c is larger than the microwave cavity vacuum Rabi splitting, such that ∣ω−Re⁡{ξc}∣≪κc|\omega-\operatorname{Re}\{\xi_c\}|\ll\kappa_c applies throughout Figure 2(b), while the optical reservoir coupling κa\kappa_a is smaller than the optical cavity vacuum Rabi splitting. If both cavities operate in the strong coupling limit (not shown), the highest efficiencies in Figure 2(b) will occur near where the C=1C=1 contours overlap with the four crosses. We also see that appreciable efficiencies are obtained as ω+Δ\omega+\Delta approaches ±NAg13\pm\sqrt{N_{\mathrm{A}}}g_{13}, and at the circular point defined by the origin Δ=ω=0\Delta=\omega=0. The latter operation point is counterintuitive because it does not occur near center-microwave-cavity and center-optical-cavity hybridized states, and is further discussed in Supplementary Information S1.G. Both signal photon frequencies are equal to the respective bare cavity and center resonance frequencies, substantially off-resonance from the vacuum Rabi-split center-optical-cavity hybrid states.

The conversion efficiency can be optimized at the operating point with photons at the bare frequencies (Δ=ω=0\Delta=\omega=0) by choosing parameters to enable matching (C=1C=1) at this point. A map of the efficiency is plotted in Figure 2(c) with κaex\kappa_a^{\mathrm{ex}} increased to 2 GHz, while leaving other parameters fixed, to obtain C=1C=1 at the origin, which occurs when

Ωp=2NAg12g13κaκc.(8)\Omega_p=\frac{2N_{\mathrm{A}}g_{12}g_{13}}{\sqrt{\kappa_a\kappa_c}}. \tag*{(8)}

Notably, the co-operativity is enhanced significantly in the strong ensemble-cavity coupling case compared to the weak coupling case. For the latter, δ1i≫g1iNA\delta_{1i}\gg g_{1i}\sqrt{N_{\mathrm{A}}} is needed to avoid hybridization of individual cavity photons to the ensemble, and ξac=NAg12g13Ωp/(δ12δ13−Ωp2)\xi_{ac}=N_{\mathrm{A}}g_{12}g_{13}\Omega_p/(\delta_{12}\delta_{13}-\Omega_p^2). Smaller detunings can be considered for the strong ensemble-cavity coupled case, where for δ12=δ13=0\delta_{12}=\delta_{13}=0 and ω=Δ=0\omega=\Delta=0, ξac=NAg12g13Ωp/(γ12γ13−Ωp2)\xi_{ac}=N_{\mathrm{A}}g_{12}g_{13}\Omega_p/(\gamma_{12}\gamma_{13}-\Omega_p^2), provided that Ωp2≫γ12γ13\Omega_p^2\gg\gamma_{12}\gamma_{13} to ensure low loss. Using the inequalities δ1i≫g1iNA\delta_{1i}\gg g_{1i}\sqrt{N_{\mathrm{A}}}, we see that co-operativity is enhanced by (g12g13NA/Ωp2−1)2≫12(g_{12}g_{13}N_{\mathrm{A}}/\Omega_p^2-1)^2\gg12 (16) for T- (Er-) center parameters in Table I. For example, with δ1i=4g1iNA\delta_{1i}=4g_{1i}\sqrt{N_{\mathrm{A}}}, the co-operativity enhancement is 300

ParameterT-centerEr-center
(B)Ωp\Omega_p4 MHz4.5 MHz
(B)NAN_{\mathrm{A}}10610^610710^7
(B)κcex\kappa_c^{\mathrm{ex}}0.8 MHz0.8 MHz
(B)κaex\kappa_a^{\mathrm{ex}} [Fig. 2(b)]0.25 GHz
(B)κaex\kappa_a^{\mathrm{ex}} [Fig. 2(c)], Fig. 42 GHz2 GHz
(C)g12g_{12}40 Hz0.3 kHz
(C)g13g_{13}2 MHz30 kHz
(C)γ12\gamma_{12}1 Hz1 kHz
(C)γ13\gamma_{13}1 MHz10 kHz

Table 1. Parameters considered for the T- and Er-centers.

(400) for T- (Er-) centers. This enhancement is important because it allows us to increase the co-operativity with fixed center density and pump power (Rabi frequency) by reducing detunings to the strong coupling regime.

Inhomogeneous broadening: A key advantage of the operating point δ12=δ13=ω=Δ=0\delta_{12}=\delta_{13}=\omega=\Delta=0 appears when considering the inhomogeneous broadening of the centers. The Supplementary Information describes how the efficiency is rigorously calculated when including a two dimensional uncorrelated Gaussian distribution of widths σ13\sigma_{13} and σ12\sigma_{12} for the optical and microwave detunings centered around mean values ⟨δ13⟩\langle\delta_{13}\rangle and ⟨δ12⟩\langle\delta_{12}\rangle. Operating at zero detunings (⟨δ12⟩=⟨δ13⟩=ω=Δ=0\langle\delta_{12}\rangle=\langle\delta_{13}\rangle=\omega=\Delta=0) makes ξa\xi_a and ξc\xi_c antisymmetric functions of δ12\delta_{12} and δ13\delta_{13}, respectively (see Eq. (3a,b) and Fig. S2). Therefore, the summation over the inhomogeneously broadened δ12/13\delta_{12/13} yields Re⁡{ξa}=Re⁡{ξc}=0\operatorname{Re}\{\xi_a\}=\operatorname{Re}\{\xi_c\}=0, which fulfills conditions (i) and (ii) at ω=Δ=0\omega=\Delta=0. We therefore obtain enhanced robustness to inhomogeneous broadening by operating at zero detunings.

Another condition that assists in maintaining high efficiency for inhomogeneous ensembles is Ωp≫σ12σ13\Omega_p\gg\sqrt{\sigma_{12}\sigma_{13}}. If Ωp≪σ12σ13\Omega_p\ll\sqrt{\sigma_{12}\sigma_{13}}, ξac\xi_{ac} and the co-operativity are reduced. This is because terms with positive and negative δ12/13,k\delta_{12/13,k} cancel each other since ξac\xi_{ac} is an odd function of δ12/13,k\delta_{12/13,k}. However, when Ωp≫σ12σ13\Omega_p\gg\sqrt{\sigma_{12}\sigma_{13}}, ξac\xi_{ac} is almost independent of δ12/13,k\delta_{12/13,k}. This condition extends the region where the magneto-optic coupling ξac\xi_{ac} is independent of δ12\delta_{12} and δ13\delta_{13} beyond the inhomogeneous broadenings.

Color center loss: The color centers that are responsible for microwave-optical conversion also introduce undesirable losses 2Im⁡{ξa/c}2\operatorname{Im}\{\xi_{a/c}\}. For a strong pump, the color center loss can easily be evaluated, and the condition of high external quantum efficiency where reservoir coupling exceeds the loss simplifies to κa≫NAg132γ12/Ωp2\kappa_a\gg N_{\mathrm{A}}g_{13}^2\gamma_{12}/\Omega_p^2 and κc≫NAg122γ13/Ωp2\kappa_c\gg N_{\mathrm{A}}g_{12}^2\gamma_{13}/\Omega_p^2. These conditions set practical bounds on NAN_{\mathrm{A}}, i.e., the color center density in the host material, for given pump and cavity couplings.

Filling factor and cavities losses

High quantum efficiency in the proposed device relies on appreciable spatial overlap of the color centers to the microwave signal, optical pump, and optical signal modes (quantified by filling factors) and low losses. The proposed device is shown in Figure 1(c,d). Here, the optical signal and pump are taken to be quasi-transverse electric (TE-like) and quasi-transverse magnetic (TM-like) modes, respectively, though a design based on coupled racetracks with two TE-like modes is also possible [17, 18]. The microwave cavity is a distributed superconducting resonator loaded with an interdigitated capacitor (IDC). The IDC loading increases the filling factor by reducing the length of the microwave cavity to match the optical cavity, reduces the characteristic impedance [42, 50], and enhances the zero-point magnetic fluctuations [51, 52]. We consider an Nb resonator, which is robust to Tesla-level magnetic fields [53], though NbTiN is a viable alternative [54, 55]. After calculating the filling factor, we determine the optical and microwave losses due to absorption of optical photons in the superconductor, which generates quasiparticles, in addition to the Si two-photon and free-carrier absorption losses. We use these results to predict device performance in Sec. III C.

We begin by calculating the filling factor Fabcijk=∣∫Voψaiψbjψck dV∣/VoF_{abc}^{ijk}=|\int_{V_o}\psi_a^i\psi_b^j\psi_c^k\,\mathrm{d}V|/V_o for the unitless mode fields ψmi\psi_m^i, for m∈{a,b,c}m\in\{a,b,c\} and field directions i,j,k∈{x,y,z}i,j,k\in\{x,y,z\} (see the Supplementary Information for details). We assume a fixed resonator width wm=2 μmw_m=2\,\mu\mathrm{m}. Figure 3(a) shows example contours for the TE00_{00} optical signal mode electric field ψax\psi_a^x along xx and the microwave mode magnetic field ψcz\psi_c^z along zz at the narrow part of the IDC. The filling factor FabcxzxF_{abc}^{xzx} is shown in Figure 3(b) as a function of distance domd_{\mathrm{om}} between the optical and the microwave cavities, for different waveguide cross-sectional areas (wo,to)(w_o,t_o). We see that (i) as domd_{\mathrm{om}} increases, FF only modestly decreases, and that (ii) larger optical waveguide cross-sections yield larger filling factors, effectively capturing more microwave magnetic field.

Filling factor, optical loss rates to superconductor, and microwave loss rate

Figure 3. Filling factor, optical loss rates to superconductor, and microwave loss rate. (a) Calculated contours of TE00_{00} mode aa electric field along xx and microwave mode cc magnetic field along zz. (b) Filling factor versus domd_{\mathrm{om}}. A1=0.4×0.22 μm2A_1=0.4\times0.22\,\mu\mathrm{m}^2, A2=0.7×0.5 μm2A_2=0.7\times0.5\,\mu\mathrm{m}^2, and A3=1.3×1.2 μm2A_3=1.3\times1.2\,\mu\mathrm{m}^2 (A=wo×toA=w_o\times t_o). (c) Optical mode loss rates due to optical absorption in the superconductor, versus domd_{\mathrm{om}}, for the same geometries. The superconducting resonator geometry is tm=20t_m=20 nm and wm=2 μmw_m=2\,\mu\mathrm{m}, and refractive index ≈1+7i\approx1+7i for Niobium at 1300 nm and 4 K [56]. (d) Quasiparticle loss rate of the microwave mode versus optical pump photons number at κbSC=300\kappa_b^{\mathrm{SC}}=300 Hz for three different superconductor volumes.

We next evaluate the optical losses. Despite the weak dependence of the filling factor on distance, the loss rates of optical photons to the superconductor κa,bSC\kappa^{\mathrm{SC}}_{a,b} reduce exponentially with distance domd_{\mathrm{om}}, as shown in Figure 3(c). Indeed, κa,bSC\kappa^{\mathrm{SC}}_{a,b} decreases exponentially by ten orders of magnitude as domd_{\mathrm{om}} increases from 0.2 μm0.2\ \mu\mathrm{m} to 1.4 μm1.4\ \mu\mathrm{m}, although FF decreases modestly (by a factor of ∼2\sim2) over the same range (Figure 3(b)). Furthermore, larger optical cross-sections reduce the evanescent penetration of the pump mode into the superconductor. Beyond quasiparticle generation in the superconductor and color center loss, we also consider nonlinear optical loss in Si from two-photon absorption (TPA) and free carrier absorption (FCA). Detailed calculations for these mechanisms are presented in the Supplementary Information. We show that when these loss mechanisms become appreciable, they reduce external quantum efficiency and cause NpN_p to saturate with pump power, which is unfavourable for efficiency and noise. Smaller mode volumes enhance co-operativity but increase nonlinear loss by enhancing fields.

Next we calculate the loss rate of the microwave photons in the superconductor κcQP\kappa^{\mathrm{QP}}_c due to excess quasiparticles, an important loss mechanism in MOCs [16, 17, 18, 19, 57, 58, 59]. This can be quantified by [60, 61]

κcQP=ωcαkiπnQP(Pl,T)n0Δs2Δsℏωcf(T)\kappa^{\mathrm{QP}}_c = \omega_c \frac{\alpha_{\mathrm{ki}}}{\pi} \frac{n_{\mathrm{QP}}(P_l,T)}{n_0\Delta_s} \sqrt{\frac{2\Delta_s}{\hbar\omega_c}} f(T)

where αki\alpha_{\mathrm{ki}} is the kinetic inductance ratio, n0n_0 is the density of states at the Fermi energy of the superconductor, Δs\Delta_s is the superconducting gap, nQPn_{\mathrm{QP}} is the quasiparticle density which depends on pump power leakage Pl=ℏωpNpκaSCP_l = \hbar\omega_p N_p\kappa^{\mathrm{SC}}_a and superconductor temperature TT, and f(T)f(T) is a temperature-dependant factor that approaches 1 when kBT≪ℏωck_{\mathrm{B}}T \ll\hbar\omega_c. nQPn_{\mathrm{QP}} is affected by the pump directly through the generation of quasiparticles, and indirectly by increasing the steady state superconductor temperature TT. We calculate TT from a heat flow model for thin film superconductors [62], and nQPn_{\mathrm{QP}} from the quasiparticle steady state solution [61, 63], ignoring local heating in the Si resonator, expected to be less important in pulsed operation of MOCs, and which is difficult to calculate.

Results for the quasiparticle loss rate κcQP\kappa^{\mathrm{QP}}_c are shown in Figure 3(d) versus NpN_p for three different microwave resonator volumes. We note that the resonator volume VmV_m considered in the calculation is the volume of the central line only (i.e., the inductive part where most of the quasiparticles are initially generated), as a worst case limit for the loss. The microwave cavity shows increasing quasiparticle loss with NpN_p, and cavities of smaller volume exhibit higher κcQP\kappa^{\mathrm{QP}}_c at any leakage power. These results emphasize (i) the robustness of larger microwave cavities to the optical pump and (ii) exponential reduction in microwave losses due to quasiparticle generation on the distance domd_{\mathrm{om}} between the optical and microwave resonators, while maintaining a high filling factor.

Total efficiency and added noise

We now predict the total quantum efficiency and added noise for our MOC operating with photons on resonance with bare microwave/optical center transitions and cavity resonances. We consider inhomogeneous broadening and all sources of loss, including color center loss (Section IIIA) and other losses (Section IIIB). Microwave and optical losses are separated in the expression for total efficiency, η=ηinηaηc\eta= \eta_{\mathrm{in}}\eta_a\eta_c, where ηin=∣4C∣/(C+1)2\eta_{\mathrm{in}} = |4C|/(C+1)^2 is the internal efficiency and ηa=κaex/κa\eta_a = \kappa^{\mathrm{ex}}_a/\kappa_a (ηc=κcex/κc\eta_c = \kappa^{\mathrm{ex}}_c/\kappa_c), and κa\kappa_a (κc\kappa_c) is now redefined as the total optical (microwave) loss including color center loss. We compute the vacuum couplings and Rabi frequency for the T-center and Er-center in Si from experimentally calibrated optical and magnetic dipoles [46, 64, 65] and realistic cavity volumes, using g13=d13ℏωcFaϵ0ϵrVog_{13} = d_{13}\sqrt{\frac{\hbar\omega_c F_a}{\epsilon_0\epsilon_r V_o}}, g12=μ12ℏωcFcμ0Vog_{12} = \mu_{12}\sqrt{\frac{\hbar\omega_c F_c}{\mu_0 V_o}} and ℏΩp=d23ℏωpNpFbϵ0ϵrVo\hbar\Omega_p = d_{23}\sqrt{\frac{\hbar\omega_p N_p F_b}{\epsilon_0\epsilon_r V_o}}. Here, d13d_{13} (d23d_{23}) is the dipole of the ∣1⟩↔∣3⟩|1\rangle\leftrightarrow|3\rangle (∣2⟩↔∣3⟩|2\rangle\leftrightarrow|3\rangle) optical signal (pump) transition, μ12\mu_{12} is the magnetic dipole of the ∣1⟩↔∣2⟩|1\rangle\leftrightarrow|2\rangle microwave transition, VoV_o is the volume of the nonlinear medium, FiF_i is the unitless filling factor of mode i∈{a,b,c}i \in\{a,b,c\}, and Fabc=FaFbFcF_{abc} = \sqrt{F_aF_bF_c} for spatially uniform bosonic modes. We consider cavity coupling losses of κaex=2 GHz\kappa^{\mathrm{ex}}_a = 2\ \mathrm{GHz} (Qaex∼105Q^{\mathrm{ex}}_a \sim10^5) and κcex=0.8 MHz\kappa^{\mathrm{ex}}_c = 0.8\ \mathrm{MHz} (Qcex∼104Q^{\mathrm{ex}}_c \sim10^4). For the T-center, we use Np=50N_p = 50, while for the Er-center we use Np=50,000N_p = 50,000 to compensate for the relatively small optical dipole of the Er-center.

Results are presented in Figure 4 for T-centers and Er-centers versus the center density ρ=NA/Vo\rho= N_A/V_o using color center parameters from Table I, illustrating the potential of our proposed approach for efficient transduction. In both cases we predict efficiency as high as 95% with the number of noise photons close to zero.

Figure 4. Efficiencies and noise for (a,c,e) T-center and (b,d,f) Er-center at zero detunings with inhomogeneous broadening (IB). (a,b) Efficiency and (c,d) noise dependence on the color center density ρ\rho at fixed number of pump photons; Np=50N_p = 50 in (a,c) and Np=50,000N_p = 50,000 in (b,d) for parameters in Table I. Optical IB of 30 MHz is considered in (a,c) [46] and 100 MHz in (c,d) [64]. (e,f) Optimum efficiency versus ρ\rho and NpN_p at different values for the optical IB. At each value for NpN_p, ρ\rho is selected to give the maximum internal efficiency at zero detunings, according to the first condition in Eq. (8). Microwave IB of 100 kHz is considered in all calculations. We consider Vo=1100×1.3×1.2 μm3V_o = 1100 \times1.3 \times1.2\ \mu\mathrm{m}^{3} for the racetrack resonator and Vm=1000×2×0.02 μm3V_m = 1000 \times2 \times0.02\ \mu\mathrm{m}^{3} for the inductive central line. We note that the phase-matching condition is satisfied for these dimensions for the TE00_{00}, TM00_{00}, and full-wave microwave modes (see the Supplementary Information).

We find the efficiency of the T-center device is limited by the optical external efficiency, ηa\eta_a (Figure 4(a)), while for the Er-center, the efficiency is limited by the microwave external efficiency, ηc\eta_c (Figure 4(b)). This is because the relatively strong optical dipole (magnetic dipole) of the T-center (Er-center) results in a large center-induced optical (microwave) loss, which increases with the center density. One way to alleviate the effect of the center-induced loss in one of the cavities is to increase its reservoir coupling and maintain the matching condition by decreasing the reservoir coupling of the other cavity. Hence, color centers with strong optical dipoles, such as the T-center, require an optical cavity with a relatively small QaexQ^{\mathrm{ex}}_a and a microwave cavity with a large QcexQ^{\mathrm{ex}}_c, while the opposite is true for color centers with strong microwave dipoles, such as the Er-center.

Results for added noise (Eq. (4)) are presented in Figure 4(c,Figure 4d). The microwave-optical noise, NMON_{\mathrm{MO}}, increases with density due to increasing the center-induced microwave loss. In the case of Er in Figure 4(d), NMON_{\mathrm{MO}} is independent of the density at small densities, because the microwave intrinsic loss is dominated by the pumpinduced loss rather than the center-induced loss. For the optical-microwave noise, NOMN_{\mathrm{OM}}, the increase of the density has two effects. First, it increases the microwave intrinsic loss, which increases the noise linearly, assuming an over-coupled optical cavity. Second, it increases ξac\xi_{\mathrm{ac}} linearly, which reduces the noise quadratically, giving an overall linear decrease in the noise with increasing density. The two noise lines intersect when matching (C=1C = 1) is obtained, as expected from Eq. (4) for over-coupled cavities. Importantly, for both the Er- and T-centers, the calculated noise at the optimum density is significantly less than the threshold, 0.5, for the quantum state transfer by direct conversion [1].

We study the effect of the inhomogeneous broadening on the conversion efficiency in Figure 4(e,Figure 4f). The total efficiency is plotted for different optical inhomogeneous broadenings versus the center density and the number of pump photons, which are varied together to keep the condition C=1C = 1 satisfied at all points. As the inhomogeneous broadening increases, a larger number of pump photons and higher center density are required to realize the near-unity efficiency. If the number of pump photons is too large, the pump-induced microwave loss lowers

the microwave external efficiency, as shown in Figure 4(f). Achieving high efficiency using our MOC relies on the realization of small inhomogeneous broadening for a practical center density.

Several practical challenges present themselves in real devices. For example, the narrow inhomogeneous broadening of the T-center that has been measured for isotope-purified bulk Si [46] has yet to be demonstrated in Si integrated optical cavities. Another potential challenge is integrating a superconducting resonator with Q∼50,000Q \sim50,000 on a silicon-on-insulator platform. However, Qi>105Q_i > 10^{5} has recently been realized for suspended resonators using new fabrication approaches [66]. Furthermore, employing suitable techniques for tuning the optical modes will be necessary for frequency matching the color center transitions and for fulfilling the triple-resonance condition with the microwave mode. Color centres with multiple resonance lines represent a challenge. For both T- and Er-centers, multiple resonance lines appear in magnetic field [46, 67, 68]. Additionally, Er can show multiple resonance lines at zero magnetic field [64, 69, 70]; however the number of these states can be significantly reduced by careful sample preparation [65]. All these aspects require careful design and fabrication of the device for experimental realization.

Conclusion

We have developed a theory of microwave-optical conversion for arbitrary bare microwave/optical resonator frequencies relative to the bare microwave/optical transitions of an ensemble of color centers, including on-resonance where strong ensemble-cavity coupling effects are obtained. We find high-efficiency operating points for microwave and optical signal photon frequencies that are nearly resonant with hybrid center-cavity resonances, and a counterintuitive operating point where microwave and optical signal photons are nearly resonant with the bare center-cavity frequencies, but far from the hybrid center-cavity resonances. The strong coupling regime offers significantly enhanced nonlinearity at lower pump powers for conversion, and the counter-intuitive operating point offers enhanced robustness to inhomogeneous broadening. Accounting for inhomogeneous broadening, color center-induced loss, Si two-photon and free-carrier absorption, and optical and microwave mode losses due to optically generated quasiparticles, we find that high conversion efficiency (∼95%\sim95\%) and low noise (≪1\ll1 photon) is possible for practically obtainable optical and microwave intrinsic quality factors of ∼106\sim10^{6} and ∼5×104\sim5 \times10^{4} respectively, and around ∼1\sim1 GHz of inhomogeneous broadening.

Acknowledgments

The authors acknowledge Lukas Chrostowski, Marek Korkusinski and Shabir Barzanjeh for helpful discussions and Alexey Lyasota and Sven Rogge for pointing out new work on Er doped Si. This work was undertaken with support from the Stewart Blusson Quantum Matter Institute (SBQMI), and the Canada First Research Excellence Fund, Quantum Materials and Future Technologies Program. JS and JFY acknowledge financial support from the National Science and Research Council of Canada (NSERC) in the Discovery Grant program and Quantum Alliance Consortium “CanQuEST”, from the National Research Council in the Quantum Sensors Challenge program, and from Defence Canada (Innovation for Defence Excellence and Security, IDEaS). JS and JFY acknowledge financial support from the Canadian Foundation for Innovation (CFI) John Edwards Leaders Foundation and CFI Innovation Fund. MK acknowledges financial support from the SBQMI QuEST fellowship program. PSK acknowledges financial support from the NSERC CREATE in Quantum Computing Program (Grant Number 543245). The authors acknowledge CMC Microsystems for the provision of computer aided design tools that were essential to obtain the results presented here. This research was supported in part through computational resources provided by Advanced Research Computing at the University of British Columbia.

References

References

  1. [1]M. M. Wolf, D. Pérez-García, and G. Giedke, Quantum capacities of bosonic channels, Physical review letters 98, 130501 (2007).pubmed.ncbi.nlm.nih.gov/17501173
  2. [2]H. J. Kimble, The quantum internet, Nature 453, 1023 (2008).DOI
  3. [3]R. Barends, J. Kelly, A. Megrant, A. Veitia, D. Sank, E. Jeffrey, T. C. White, J. Mutus, A. G. Fowler, B. Campbell, et al., Superconducting quantum circuits at the surface code threshold for fault tolerance, Nature 508, 500 (2014).
  4. [4]L. B. Nguyen, G. Koolstra, Y. Kim, A. Morvan, T. Chistolini, S. Singh, K. N. Nesterov, C. Jünger, L. Chen, Z. Pedramrazi, et al., Blueprint for a high-performance fluxonium quantum processor, PRX Quantum 3, 037001 (2022).DOI
  5. [5]N. W. Hendrickx, W. I. Lawrie, M. Russ, F. van Riggelen, S. L. de Snoo, R. N. Schouten, A. Sammak, G. Scappucci, and M. Veldhorst, A four-qubit germanium quantum processor, Nature 591, 580 (2021).
  6. [6]S. G. Philips, M. T. Mądzik, S. V. Amitonov, S. L. de Snoo, M. Russ, N. Kalhor, C. Volk, W. I. Lawrie, D. Brousse, L. Tryputen, et al., Universal control of a six-qubit quantum processor in silicon, Nature 609, 919 (2022).
  7. [7]S. Barzanjeh, M. Abdi, G. J. Milburn, P. Tombesi, and D. Vitali, Reversible optical-to-microwave quantum interface, Physical Review Letters 109, 130503 (2012).pubmed.ncbi.nlm.nih.gov/23030075
  8. [8]L. A. Williamson, Y.-H. Chen, and J. J. Longdell, Magneto-optic modulator with unit quantum efficiency, Physical review letters 113, 203601 (2014).pubmed.ncbi.nlm.nih.gov/25432041
  9. [9]C. Javerzac-Galy, K. Plekhanov, N. Bernier, L. D. Toth, A. K. Feofanov, and T. J. Kippenberg, On-chip microwave-to-optical quantum coherent converter based on a superconducting resonator coupled to an electro-optic microresonator, Physical Review A 94, 053815 (2016).
  10. [10]B. Li, P.-B. Li, Y. Zhou, S.-L. Ma, and F.-L. Li, Quantum microwave-optical interface with nitrogen-vacancy centers in diamond, Phys. Rev. A 96, 032342 (2017).DOI
  11. [11]M. Wu, E. Zeuthen, K. C. Balram, and K. Srinivasan, Microwave-to-optical transduction using a mechanical supermode for coupling piezoelectric and optomechanical resonators, Phys. Rev. Appl. 13, 014027 (2020).DOI
  12. [12]T. Liu, J.-L. Zhao, B.-Q. Guo, Q.-C. Wu, Y.-H. Zhou, and C.-P. Yang, One-step implementation of a coherent conversion between microwave and optical cavities via an ensemble of nitrogen-vacancy centers, Phys. Rev. A 103, 023706 (2021).DOI
  13. [13]P. S. Barnett and J. J. Longdell, Theory of microwave-optical conversion using rare-earth-ion dopants, Phys. Rev. A 102, 063718 (2020).DOI
  14. [14]A. Rueda, F. Sedlmeir, M. C. Collodo, U. Vogl, B. Stiller, G. Schunk, D. V. Strekalov, C. Marquardt, J. M. Fink, O. Painter, G. Leuchs, and H. G. L. Schwefel, Efficient microwave to optical photon conversion: an electro-optical realization, Optica 3, 597 (2016).DOI
  15. [15]W. Hease, A. Rueda, R. Sahu, M. Wulf, G. Arnold, H. G. Schwefel, and J. M. Fink, Bidirectional electro-optic wavelength conversion in the quantum ground state, PRX Quantum 1, 020315 (2020).
  16. [16]L. Fan, C.-L. Zou, R. Cheng, X. Guo, X. Han, Z. Gong, S. Wang, and H. X. Tang, Superconducting cavity electro-optics: a platform for coherent photon conversion between superconducting and photonic circuits, Science advances 4, eaar4994 (2018).arxiv.org/abs/1805.04509
  17. [17]J. Holzgrafe, N. Sinclair, D. Zhu, A. Shams-Ansari, M. Colangelo, Y. Hu, M. Zhang, K. K. Berggren, and M. Lončar, Cavity electro-optics in thin-film lithium niobate for efficient microwave-to-optical transduction, Optica 7, 1714 (2020).
  18. [18]T. P. McKenna, J. D. Witmer, R. N. Patel, W. Jiang, R. Van Laer, P. Arrangoiz-Arriola, E. A. Wollack, J. F. Herrmann, and A. H. Safavi-Naeini, Cryogenic microwave-to-optical conversion using a triply resonant lithium-niobate-on-sapphire transducer, Optica 7, 1737 (2020).arxiv.org/abs/2005.00897
  19. [19]Y. Xu, A. A. Sayem, L. Fan, C.-L. Zou, S. Wang, R. Cheng, W. Fu, L. Yang, M. Xu, and H. X. Tang, Bidirectional interconversion of microwave and light with thin-film lithium niobate, Nature communications 12, 4453 (2021).DOI
  20. [20]J. D. Witmer, T. P. McKenna, P. Arrangoiz-Arriola, R. Van Laer, E. A. Wollack, F. Lin, A. K. Jen, J. Luo, and A. H. Safavi-Naeini, A silicon-organic hybrid platform for quantum microwave-to-optical transduction, Quantum Science and Technology 5, 034004 (2020).arxiv.org/abs/1912.10346
  21. [21]R. Sahu, W. Hease, A. Rueda, G. Arnold, L. Qiu, and J. M. Fink, Quantum-enabled operation of a microwave-optical interface, Nature communications 13, 1276 (2022).
  22. [22]R. Sahu, L. Qiu, W. Hease, G. Arnold, Y. Minoguchi, P. Rabl, and J. M. Fink, Entangling microwaves with light, Science 380, 718 (2023).DOI
  23. [23]A. P. Higginbotham, P. Burns, M. Urmey, R. Peterson, N. Kampel, B. Brubaker, G. Smith, K. Lehnert, and C. Regal, Harnessing electro-optic correlations in an efficient mechanical converter, Nature Physics 14, 1038 (2018).DOI
  24. [24]M. Mirhosseini, A. Sipahigil, M. Kalaee, and O. Painter, Superconducting qubit to optical photon transduction, Nature 588, 599 (2020).DOI
  25. [25]M. Forsch, R. Stockill, A. Wallucks, I. Marinković, C. Gärtner, R. A. Norte, F. van Otten, A. Fiore, K. Srinivasan, and S. Gröblacher, Microwave-to-optics conversion using a mechanical oscillator in its quantum ground state, Nature Physics 16, 69 (2020).DOI
  26. [26]B. M. Brubaker, J. M. Kindem, M. D. Urmey, S. Mittal, R. D. Delaney, P. S. Burns, M. R. Vissers, K. W. Lehnert, and C. A. Regal, Optomechanical ground-state cooling in a continuous and efficient electro-optic transducer, Physical Review X 12, 021062 (2022).DOI
  27. [27]M. J. Weaver, P. Duivestein, A. C. Bernasconi, S. Scharmer, M. Lemang, T. C. van Thiel, F. Hijazi, B. Hensen, S. Gröblacher, and R. Stockill, An integrated microwave-to-optics interface for scalable quantum computing, Nature Nanotechnology 19, 166 (2024).DOI
  28. [28]S. Meesala, S. Wood, D. Lake, P. Chiappina, C. Zhong, A. D. Beyer, M. D. Shaw, L. Jiang, and O. Painter, Non-classical microwave-optical photon pair generation with a chip-scale transducer, Nature Physics 20, 871 (2024).arxiv.org/abs/2303.17684
  29. [29]R. Hisatomi, A. Osada, Y. Tabuchi, T. Ishikawa, A. Noguchi, R. Yamazaki, K. Usami, and Y. Nakamura, Bidirectional conversion between microwave and light via ferromagnetic magnons, Phys. Rev. B 93, 174427 (2016).DOI
  30. [30]Y. S. Ihn, S.-Y. Lee, D. Kim, S. H. Yim, and Z. Kim, Coherent multimode conversion from microwave to optical wave via a magnon-cavity hybrid system, Phys. Rev. B 102, 064418 (2020).arxiv.org/abs/2007.15299
  31. [31]N. Zhu, X. Zhang, X. Han, C.-L. Zou, C. Zhong, C.-H. Wang, L. Jiang, and H. X. Tang, Waveguide cavity optomechanics for microwave-to-optics conversion, Optica 7, 1291 (2020).DOI
  32. [32]T. O. Puel, A. T. Turflinger, S. P. Horvath, J. D. Thompson, and M. E. Flatté, Enhancement of microwave to optical spin-based quantum transduction via a magnon mode, arXiv preprint arXiv:2411.12870 (2024).DOI
  33. [33]I. Lekavicius, D. A. Golter, T. Oo, and H. Wang, Transfer of phase information between microwave and optical fields via an electron spin, Phys. Rev. Lett. 119, 063601 (2017).
  34. [34]X. Fernandez-Gonzalvo, Y.-H. Chen, C. Yin, S. Rogge, and J. J. Longdell, Coherent frequency up-conversion of microwaves to the optical telecommunications band in an er: YSO crystal, Physical Review A 92, 062313 (2015).
  35. [35]X. Fernandez-Gonzalvo, S. P. Horvath, Y.-H. Chen, and J. J. Longdell, Cavity-enhanced raman heterodyne spectroscopy in er3+ : y2sio5 for microwave to optical signal conversion, Phys. Rev. A 100, 033807 (2019).
  36. [36]J. G. Bartholomew, J. Rochman, T. Xie, J. M. Kindem, A. Ruskuc, I. Craiciu, M. Lei, and A. Faraon, On-chip coherent microwave-to-optical transduction mediated by ytterbium in yvo4, Nature communications 11, 3266 (2020).
  37. [37]J. Rochman, T. Xie, J. G. Bartholomew, K. Schwab, and A. Faraon, Microwave-to-optical transduction with erbium ions coupled to planar photonic and superconducting resonators, Nature Communications 14, 1153 (2023).DOI
  38. [38]X. Han, W. Fu, C.-L. Zou, L. Jiang, and H. X. Tang, Microwave-optical quantum frequency conversion, Optica 8, 1050 (2021).DOI
  39. [39]T. Xie, J. Rochman, J. G. Bartholomew, A. Ruskuc, J. M. Kindem, I. Craiciu, C. W. Thiel, R. L. Cone, and A. Faraon, Characterization of er3+ : yvo4 for microwave to optical transduction, Phys. Rev. B 104, 054111 (2021).DOI
  40. [40]D. B. Higginbottom, F. K. Asadi, C. Chartrand, J.-W. Ji, L. Bergeron, M. L. Thewalt, C. Simon, and S. Simmons, Memory and transduction prospects for silicon t center devices, PRX Quantum 4, 020308 (2023).DOI
  41. [41]T. Xie, R. Fukumori, J. Li, and A. Faraon, Scalable microwave-to-optical transducers at single photon level with spins, arXiv preprint arXiv:2407.08879 (2024).DOI
  42. [42]M. Malnou, M. Vissers, J. Wheeler, J. Aumentado, J. Hubmayr, J. Ullom, and J. Gao, Three-wave mixing kinetic inductance traveling-wave amplifier with near- [43] A. M. Tyryshkin, S. Tojo, J. J. Morton, H. Riemann, N. V. Abrosimov, P. Becker, H.-J. Pohl, T. Schenkel, M. L. Thewalt, K. M. Itoh, et al., Electron spin coherence exceeding seconds in high-purity silicon, Nature materials 11, 143 (2012).
  43. [44]K. Saeedi, S. Simmons, J. Z. Salvail, P. Dluhy, H. Riemann, N. V. Abrosimov, P. Becker, H.-J. Pohl, J. J. Morton, and M. L. Thewalt, Room-temperature quantum bit storage exceeding 39 minutes using ionized donors in silicon-28, Science 342, 830 (2013).DOI
  44. [45]T. Kobayashi, J. Salfi, C. Chua, J. Van Der Heijden, M. G. House, D. Culcer, W. D. Hutchinson, B. C. Johnson, J. C. McCallum, H. Riemann, et al., Engineering long spin coherence times of spin–orbit qubits in silicon, Nature Materials 20, 38 (2021).DOI
  45. [46]L. Bergeron, C. Chartrand, A. Kurkjian, K. Morse, H. Riemann, N. Abrosimov, P. Becker, H.-J. Pohl, M. Thewalt, and S. Simmons, Silicon-integrated telecommunications photon-spin interface, PRX Quantum 1, 020301 (2020).DOI
  46. [47]E. MacQuarrie, C. Chartrand, D. Higginbottom, K. Morse, V. Karasyuk, S. Roorda, and S. Simmons, Generating t centres in photonic silicon-on-insulator material by ion implantation, New Journal of Physics 23, 103008 (2021).DOI
  47. [48]M. Tsang, Cavity quantum electro-optics, Physical Review A 81, 063837 (2010).DOI
  48. [49]M. Tsang, Cavity quantum electro-optics: ii. input-output relations between traveling optical and microwave fields, Physical Review A 84, 043845 (2011).DOI
  49. [50]D. J. Parker, M. Savvitskyi, W. Vine, A. Laucht, T. Duty, A. Morello, A. L. Grimsmo, and J. J. Pla, Degenerate parametric amplification via three-wave mixing using kinetic inductance, Physical Review Applied 17, 034064 (2022).DOI
  50. [51]P. Haikka, Y. Kubo, A. Beinfait, P. Bertet, and K. Mølmer, Proposal for detecting a single electron spin in a microwave resonator, Physical Review A 95, 022306 (2017).DOI
  51. [52]J. Pla, A. Beinfait, G. Pica, J. Mansir, F. Mohiyaddin, Z. Zeng, Y.-M. Niquet, A. Morello, T. Schenkel, J. Morton, et al., Strain-induced spin-resonance shifts in silicon devices, Physical Review Applied 9, 044014 (2018).DOI
  52. [53]J. G. Kroll, F. Borsoi, K. Van Der W, W. Uilhoorn, D. De Jong, M. Quintero-Pérez, D. Van Woerkom, A. Bruno, S. Plissard, D. Car, et al., Magnetic-field-resilient superconducting coplanar-waveguide resonators for hybrid circuit quantum electrodynamics experiments, Physical Review Applied 11, 064053 (2019).
  53. [54]N. Samkharadze, A. Bruno, P. Scarlino, G. Zheng, D. Di Vincenzo, L. DiCarlo, and L. V. Vandersypen, High-kinetic-inductance superconducting nanowire resonators for circuit qed in a magnetic field, Physical Review Applied 5, 044004 (2016).DOI
  54. [55]quantum-limited noise performance, PRX Quantum 2, (2023). 010302 (2021).
  55. [56]A. Golovashkin, I. Leksina, G. Motulevich, and A. Shubin, Optical properties of niobium, SOV PHYS JETP 29, 27 (1969).
  56. [57]W. Fu, M. Xu, X. Liu, C.-L. Zou, C. Zhong, X. Han, M. Shen, Y. Xu, R. Cheng, S. Wang, et al., Cavity electro-optic circuit for microwave-to-optical conversion in the quantum ground state, Physical Review A 103, 053504 (2021).DOI
  57. [58]Y. Xu, W. Fu, Y. Zhou, M. Xu, M. Shen, A. Al Sayem, and H. X. Tang, Light-induced dynamical frequency shifting of microwave photons in a superconducting electro-optic converter, Physical Review Applied 18, 064045 (2022).arxiv.org/abs/2211.10668
  58. [59]M. Xu, C. Li, Y. Xu, and H. X. Tang, Light-induced microwave noise in superconducting microwave-optical transducers, Physical Review Applied 21, 014022 (2024).arxiv.org/abs/2311.08518
  59. [60]R. Barends, J. Wenner, M. Lenander, Y. Chen, R. C. Bialczak, J. Kelly, E. Lucero, P. O’Malley, M. Mariantoni, D. Sank, et al., Minimizing quasiparticle generation from stray infrared light in superconducting quantum circuits, Applied Physics Letters 99, 113507 (2011).DOI
  60. [61]J. Zmuidzinas, Superconducting microresonators: Physics and applications, Annu. Rev. Condens. Matter Phys. 3, 169 (2012).DOI
  61. [62]M. Sidrova, A. D. Semenov, H.-W. Hübers, S. Gyger, and S. Steinhauer, Phonon heat capacity and self-heating normal domains in nbtin nanostrips, Superconductor Science and Technology 35, 105005 (2022).
  62. [63]A. Rothwarf and B. Taylor, Measurement of recombination lifetimes in superconductors, Physical Review Letters 19, 27 (1967).DOI
  63. [64]I. R. Berkman, A. Lyasota, G. G. de Boo, J. G. Bartholomew, S. Q. Lim, B. C. Johnson, J. C. McCallum, B.-B. Xu, S. Xie, N. V. Abrosimov, et al., Millisecond electron spin coherence time for erbium ions in silicon, arXiv preprint arXiv:2307.10021 (2023).arxiv.org/abs/2307.10021
  64. [65]A. Gritsch, L. Weiss, J. Früh, S. Rinner, and A. Reiserer, Narrow optical transitions in erbium-implanted silicon waveguides, Phys. Rev. X 12, 041009 (2022).
  65. [66]M. T. Fang, Suspended Trace Air-Gap Resonators for Low Loss Superconducting Circuits, Ph.D. thesis (2020).DOI
  66. [67]I. R. Berkman, A. Lyasota, G. G. de Boo, J. G. Bartholomew, B. C. Johnson, J. C. McCallum, B.-B. Xu, S. Xie, R. L. Ahlefeldt, M. J. Sellars, C. Yin, and S. Rogge, Observing er3+ sites in si with an in situ single-photon detector, Phys. Rev. Appl. 19, 014037 (2023).
  67. [68]S. Rinner, F. Burger, A. Gritsch, J. Schmitt, and A. Reiserer, Erbium emitters in commercially fabricated nanophotonic silicon waveguides, Nanophotonics 12, 3455 (2023).DOI
  68. [69]H. Przyblinska, W. Jantsch, Y. Suprun-Belevitch, M. Stepikhova, L. Palmetshofer, G. Hendorfer, A. Kozanecki, R. J. Wilson, and B. J. Sealy, Optically active erbium centers in silicon, Phys. Rev. B 54, 2532 (1996).
  69. [70]A. J. Kenyon, Erbium in silicon, Semiconductor Science and Technology 20, R65 (2005).DOI

Paper details

vlnc:W_3ccsbbv5
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents