betaFeedback

WorksPhysics and Astronomy

Compact beam position monitor using a segmented toroidal coil

Abstract

A new, compact beam position monitor based on segmented a toroidal coil surrounding the charged particle beam has been investigated. It makes use of the induced voltages in the windings instead of the induced charge imbalance on capacitor plates in the conventional beam position monitors. We theoretically investigate the response of the coils to the bunched particle beam based on a lumped element model and compare it with measurements in the laboratory and in the storage ring COSY, in terms of beam displacement. As to the frequency response of the coils, we find a resonant behavior, which may be exploited to increase the sensitivity of the device further. The resolution presently achieved is about 5 micrometer in a one second time interval for a beam current of 0.5 mA.

Introduction

Experiments searching for Electric Dipole Moments (EDMs) of charged particles using storage rings are at the forefront of the incessant quest to find new physics beyond the Standard Model (SM). These investigations bear the potential to shed light on the origin of the hitherto unexplained large matter-antimatter asymmetry in the Universe [1, 2]. The combined predictions of the SM of particle physics and of cosmology fall short of the experimentally observed asymmetry by about seven to eight orders of magnitude [3].

The JEDI collaboration (Jülich Electric Dipole moment Investigations, see http://collaborations.fz-juelich.de/ikp/jedi) is currently leading the effort to scrutinize the technical feasibility of the storage ring approach to the determination of the EDMs of protons [4]. In the framework of systematic beam and spin dynamics studies, a dedicated experiment to determine the deuteron EDM [5, 6, 7] is presently being carried out at the storage ring COSY in Jülich (Cooler Synchrotron COSY at Forschungszentrum Jülich, Germany [8, 9]).

Given the extremely small anticipated values of the EDMs of the charged particles, down to 10−2910^{-29} e cm, the control of systematic effects in the ring is of paramount importance, and high-precision monitoring of the positions of the beams in the ring constitutes one of the great challenges in these experiments. This entails precise control of the beam positions along the orbit in the machine. In order to improve the knowledge about the absolute beam orbit in COSY, various alignment campaigns were conducted, during which all magnetic elements in the machine were positioned to about 0.2 mm, or 0.2 mrad, respectively. In addition, absolute beam-offset parameters for each of the installed BPMs were obtained from a dedicated beam-based alignment effort, as described in[10].

The beam position monitors (BPMs) used at COSY are capacitive measuring devices[8, 11]. The position of the beam is determined based on the induced charge imbalance on opposing capacitor plates. The typical insertion length of such a pair of BPMs along the beam direction, providing horizontal xx and vertical yy positions, amounts to about 500 mm. For beams comprising approximately 10910^{9} particles, capacitive BPMs provide a resolution of a few µm for a measurement time of 1 s and an accuracy of about 100 µm.

These capacitive BPMs, however, appear unattractive because their length limits the number of devices that can actually be installed in a machine. It is therefore imperative to develop alternative BPMs that require significantly less installation space. In our case, it was not possible to install conventional BPMs in front of and behind a one-meter-long radio frequency Wien filter[12], essential for the EDM experiments. Therefore, a newly developed device was used to determine the beam position during the EDM measurements.

In this publication, we describe an approach based on the induction of voltages in opposing segments of a compact toroidal coil through which the beam passes, providing a position value based on the measured voltage imbalance. Previous studies of our group are discussed in proceedings[13] and in a PhD thesis[14]. Prior to our work, these so-called Rogowski coils for determining the beam current and the beam position were discussed in reference[15]. In this document, we will discuss the theoretical description and the resonant behavior in detail.

One advantage of induction coils for this particular application, apart from their mechanical simplicity, is that they offer a large sensor surface in small volume due to the large number of windings. In addition they can be operated in resonance to increase the induced voltage and that – due to the induction principle – they benefit from the high revolution frequency of the beam. Furthermore it should be noted that BPMs based on induction coils are sensitive to the time derivative of the beam current I˙\dot{I}, while capacitive BPMs are sensitive to II. Unlike BPM systems based on SQUIDs[16], they do not necessarily require low temperatures or vacuum conditions during testing and beam operation, which facilitates their development in the laboratory. Because of their short insertion length of about 5 cm, Rogowski-type BPMs appear ideally suited for a future dedicated EDM storage ring, see Chaps. 7 and 8 of Ref.[4].

This paper is organized as follows. In Sec. II, the basic principles of BPMs based on toroidal coils are discussed. In § 2, the technical realization of the BPM, the experimental test stand, as well as the calibration procedure are described. Sec. IV summarizes the results of the investigations carried out at the test stand. The results of the measurements obtained after installation in the COSY storage ring are described in § 2.4, followed by the conclusions and outlook in Sec. VI. Detailed derivations of the signal induced in a quarter coil are discussed in Appendix A, the resonance frequency of a quarter coil in Appendix B and the effect of mirror currents in Appendix C.

Toroidal coils as beam position monitors

General considerations

Coils wound on a toroidal coil body are called Rogowski coils, named after Walter Rogowski[17]. Such devices are used as AC current transformers and as beam current monitors, taking advantage of the fact that due to Ampere’s law, the induced voltage in the coil is independent of the position of the current-carrying wire passing through it[18, 19, 20, 21]. Rogowski coils are ideally suited for the application as BPMs because the magnetic flux lines of a current-carrying straight wire form concentric circles around the wire and penetrate the cross-sectional area of the windings of the Rogowski coil at right angles, resulting in an optimal induced potential difference between the ends of the coil.

Position response of differential coil setup

The magnetic difference signal of two identical induction coil sensors is a measure of the position of the beam between them, as derived in this section. The magnetic flux density generated by the beam current I(t)I(t) can be written as

B⃗(t)=μ0I(t)2πse⃗t,(1)\vec{B}(t)=\frac{\mu_{0}I(t)}{2\pi s}\vec{e}_{t}, \tag*{(1)}

where e⃗t\vec{e}_{t} is a unit vector along the circumference, μ0\mu_{0} is the vacuum magnetic permeability and ss is the radial distance from the beam center. As shown in Figure 1, the beam is perpendicular to the plane defined by the two coils.

Image not extracted

Figure 1. Beam position response of two identical induction coils (1 and 2). The zz axis points along the direction of the beam current I(t)I(t). The change of the induced magnetic flux Φ1\Phi_1 and Φ2\Phi_2, probed by the two coils, is sensitive to the displacement of the beam from the center Δx=(x2−x1)/2\Delta x=(x_2-x_1)/2.

The time derivative of the induced flux in two identical short induction coils, 1 and 2, located on a circle of diameter dd is given by

Φ˙1,2=−U1,2Nw=B˙1,2⋅S=μ0I˙2πSx1,2,(2)\dot{\Phi}_{1,2}=-\frac{U_{1,2}}{N_{w}}=\dot{B}_{1,2}\cdot S=\frac{\mu_{0}\dot{I}}{2\pi}\frac{S}{x_{1,2}}, \tag*{(2)}

where SS denotes the cross-sectional area of the coils. The ratio of induced voltage difference to voltage sum in the two coils is therefore given by

ΔUΔU‾=U1−U2U1+U2=x2−x1x2+x1=2Δxd.(3)\frac{\Delta U}{\overline{\Delta U}}=\frac{U_1-U_2}{U_1+U_2}=\frac{x_2-x_1}{x_2+x_1}=\frac{2\Delta x}{d}. \tag*{(3)}

The above considerations also apply to rotationally symmetric charge distributions of the beam, as discussed in more detail in Sec. II C.

The above derivation illustrates that a suitably segmented toroidal coil may serve as a BPM. Due to symmetry considerations, the induced voltage difference is an odd function of the beam displacement, thus yielding a linear relationship for small displacements, as illustrated in Eq. (3). A toroidal coil segmented into four elements, as indicated in Figure 2, allows one to simultaneously determine the beam position along two orthogonal coordinate axes. This specific segmentation will be discussed further in this publication.

Figure 2. Toroidal coil of radius RtR_t, segmented into four quadrants (M=0,1,2,3M = 0,1,2,3). The (beam) current I(t)I(t) passes through the coil along the zz axis. The induced voltage U0U_0 in one quarter is measured by a device with an input impedance of RoutR_{\mathrm{out}} (see also equivalent circuit diagram in Figure 3).

Evaluation of the flux in a quarter coil

For the calculation of the flux encircled by the windings on the torus, we start from the vector potential A⃗\vec{A}, which is linked to the beam current density j⃗\vec{j} via Poisson’s equation. Using cylindrical coordinates, ρ\rho, φ\varphi and zz, one finds

ΔA⃗(ρ,φ,z)=−μ0⋅j⃗(ρ,φ,z),(4)\Delta\vec{A}(\rho,\varphi,z)=-\mu_0\cdot\vec{j}(\rho,\varphi,z), \tag*{(4)}

when displacement currents are neglected. If the beam current has only a component in zz-direction, as shown in Figure 1, the same holds for the vector potential A⃗\vec{A}, and

we can regard the problem as two-dimensional. Furthermore, we consider here beams with rotationally symmetric current distributions that are much smaller than the coil diameter d=2Rtd=2R_t, so that no beam particles intercept the Rogowski coil. Such a current distribution generates a field in its outside region that bears no information about the radial current distribution, and is therefore equivalent to a pencil beam. In this case, the remaining component of the vector potential AzA_z is a harmonic function outside the beam, i.e., ΔAz=0\Delta A_z=0, which is given by the logarithm of the distance to the beam. Thus, in cylindrical coordinates we arrive at the ansatz

Az(ρ,φ)=−μ0I2πln⁡((ρcos⁡φ−x)2+(ρsin⁡φ−y)2).(5)A_z(\rho,\varphi)=-\frac{\mu_0 I}{2\pi}\ln\left(\sqrt{(\rho\cos\varphi-x)^2+(\rho\sin\varphi-y)^2}\right). \tag*{(5)}

In order to find the induced flux, an integration of AzA_z along the wire path ℓ⃗\vec{\ell} has to be performed.

The calculation of the induced magnetic fluxes ΦM\Phi_M in the four quadrants M=0,1,2,3M=0,1,2,3, discussed in Appendix A, yields a power expansion in terms of the beam displacements xx and yy. The corresponding induced voltages for any Fourier component of the periodic beam current in the storage ring are given by differentiation, which is conveniently carried out in the frequency domain by using ω=2πf\omega=2\pi f.

Making use of Eq. (43) considering the amplitudes

UM=F(ω)UMind=−F(ω)Φ˙M=−F(ω)ωΦM,(6)U_M=F(\omega)U_M^{\mathrm{ind}}=-F(\omega)\dot{\Phi}_M=-F(\omega)\omega\Phi_M, \tag*{(6)}

where the frequency response F(ω)F(\omega) is included because the quarter coil is operated in a resonance regime. Using Eq. (A18) one obtains for the induced voltage in a quadrant MM

UM(x,y,ω)=F(ω)UMind(x,y)=U^(ω)(D0(b)+∑m=1∞Dm(b)⋅Em,M(x,y)),(7)\begin{aligned} U_M(x,y,\omega)&=F(\omega)U_M^{\mathrm{ind}}(x,y)\\ &=\hat{U}(\omega)\left(D_0(b)+\sum_{m=1}^{\infty}D_m(b)\cdot E_{m,M}(x,y)\right), \tag*{(7)} \end{aligned}

where U^(ω)=μ0aNwωF(ω)I\hat{U}(\omega)=\mu_0 aN_w\omega F(\omega)I,

NwN_w is the number of windings and bb denotes the ratio of small radius aa to large radius RtR_t of the toroid (see Table I and Figure 17). The geometric functions Dm(b)D_m(b) are defined in Eq. (A17), listed in Table III, and analytical expressions for the Em,M(x,y)E_{m,M}(x,y) are given in Table IV in Appendix A. For vanishing beam displacements Em,M(0,0)=0E_{m,M}(0,0)=0, the remaining D0(b)D_0(b) describes the common voltage induced in each of the quadrants. The frequency response F(ω)F(\omega) is discussed in § 2 D and App. B.

Figure 17. Representation of the beam coordinates xx and yy, as given in cylindrical coordinates in Eq. (24), and the location of one specific coil winding. The zz axis points along the beam direction. The coil center coincides with the center of the coordinate system in the xyxy plane, the toroid is described by the two radii RtR_t and aa. The two variables used for the integration are φ\varphi and β\beta. The functional dependence of ρ(β)\rho(\beta) is given in Eq. (23).

MM01230123
mmDm(b)D_m(b)cm,0c_{m,0}cm,1c_{m,1}cm,2c_{m,2}cm,3c_{m,3}dm,0d_{m,0}dm,1d_{m,1}dm,2d_{m,2}dm,3d_{m,3}
12bπ(11−b2−1)\frac{2}{b\pi}\left(\frac{1}{\sqrt{1-b^2}}-1\right)cos⁡θ−sin⁡θ\cos\theta-\sin\theta−c1,0-c_{1,0}−c1,0-c_{1,0}c1,0c_{1,0}c1,0c_{1,0}c1,0c_{1,0}−c1,0-c_{1,0}−c1,0-c_{1,0}
2b2π(1−b2)3/2\frac{b}{2\pi(1-b^2)^{3/2}}00002cos⁡(2θ)2\cos(2\theta)−d2,0-d_{2,0}d2,0d_{2,0}−d2,0-d_{2,0}
3b3π(1−b2)5/2\frac{b}{3\pi(1-b^2)^{5/2}}−cos⁡(3θ)−sin⁡(3θ)-\cos(3\theta)-\sin(3\theta)−c3,0-c_{3,0}−c3,0-c_{3,0}c3,0c_{3,0}−c3,0-c_{3,0}−c3,0-c_{3,0}c3,0c_{3,0}c3,0c_{3,0}
4b(4+b2)16π(1−b2)7/2\frac{b(4+b^2)}{16\pi(1-b^2)^{7/2}}−2sin⁡(4θ)-2\sin(4\theta)c4,0c_{4,0}c4,0c_{4,0}c4,0c_{4,0}0000
5b(4+3b2)20π(1−b2)9/2\frac{b(4+3b^2)}{20\pi(1-b^2)^{9/2}}cos⁡(5θ)−sin⁡(5θ)\cos(5\theta)-\sin(5\theta)−c5,0-c_{5,0}−c5,0-c_{5,0}c5,0c_{5,0}c5,0c_{5,0}c5,0c_{5,0}−c5,0-c_{5,0}−c5,0-c_{5,0}
6b(8+12b2+b4)48π(1−b2)11/2\frac{b(8+12b^2+b^4)}{48\pi(1-b^2)^{11/2}}00002cos⁡(6θ)2\cos(6\theta)−d6,0-d_{6,0}d6,0d_{6,0}−d6,0-d_{6,0}

Table III. Analytical expressions for the terms Dm(b)D_m(b) (Eq. (A17)) and the coefficients cm,Mc_{m,M} and dm,Md_{m,M}, defined in Eq. (27), for the four quadrants MM up to order m=6m=6 for a coil covering an angle Δθ\Delta\theta starting at θ\theta, i.e. π/2=Δθ+2θ\pi/2=\Delta\theta+2\theta. For small values of bb, Dm(b)≈b/(mπ)D_m(b)\approx b/(m\pi).

MM0123
Em,0(x,y)E_{m,0}(x,y)Em,1(x,y)E_{m,1}(x,y)Em,2(x,y)E_{m,2}(x,y)Em,3(x,y)E_{m,3}(x,y)
1x+yRt(cos⁡(θ)−sin⁡(θ))\frac{x+y}{R_t}(\cos(\theta)-\sin(\theta))E1,0(−x,y)E_{1,0}(-x,y)E1,0(−x,−y)E_{1,0}(-x,-y)E1,0(x,−y)E_{1,0}(x,-y)
24xyRt2cos⁡(2θ)\frac{4xy}{R_t^2}\cos(2\theta)E2,0(−x,y)E_{2,0}(-x,y)E2,0(−x,−y)E_{2,0}(-x,-y)E2,0(x,−y)E_{2,0}(x,-y)
33xy2−y3−x3+3x2yRt3(−cos⁡(3θ)−sin⁡(3θ))\frac{3xy^2-y^3-x^3+3x^2y}{R_t^3}(-\cos(3\theta)-\sin(3\theta))E3,0(−x,y)E_{3,0}(-x,y)E3,0(−x,−y)E_{3,0}(-x,-y)E3,0(x,−y)E_{3,0}(x,-y)
4−2x4−6x2y2+y4Rt4sin⁡(4θ)\frac{-2x^4-6x^2y^2+y^4}{R_t^4}\sin(4\theta)E4,0(−x,y)E_{4,0}(-x,y)E4,0(−x,−y)E_{4,0}(-x,-y)E4,0(x,−y)E_{4,0}(x,-y)
5x5+y5+5xy4+5x4y−10xy2y3−10x3y2Rt5(cos⁡(5θ)−sin⁡(5θ))\frac{x^5+y^5+5xy^4+5x^4y-10xy^2y^3-10x^3y^2}{R_t^5}(\cos(5\theta)-\sin(5\theta))E5,0(−x,y)E_{5,0}(-x,y)E5,0(−x,−y)E_{5,0}(-x,-y)E5,0(x,−y)E_{5,0}(x,-y)
612xy5+12x5y−40x3y3Rt6cos⁡(6θ)\frac{12xy^5+12x^5y-40x^3y^3}{R_t^6}\cos(6\theta)E6,0(−x,y)E_{6,0}(-x,y)E6,0(−x,−y)E_{6,0}(-x,-y)E6,0(x,−y)E_{6,0}(x,-y)

Table IV. Analytical expressions for the terms Em,M(x,y)E_{m,M}(x,y) from Eq. (A19) for the four quadrants MM up to order m=6m=6 for partial coverage of the quadrants.

The symmetries that apply to the induced flux in the different quadrants are passed on to the induced voltages of the quadrants [see Eq. (37)]. Given the induced voltage U0(x,y)U_0(x,y) from Eq. (7), one can write for the induced voltages in the other quadrants,

U1(x,y)=U0(−x,y),U2(x,y)=U0(−x,−y),U3(x,y)=U0(x,−y).(8)\begin{aligned} U_1(x,y)&=U_0(-x,y),\\ U_2(x,y)&=U_0(-x,-y),\\ U_3(x,y)&=U_0(x,-y). \tag*{(8)} \end{aligned}

Therefore, assuming identical segments, the sum over the voltages of all quadrants is independent of the beam displacements,

UΣ=∑M=03UM=4U^D0(b).(9)U^{\Sigma} = \sum_{M=0}^{3} U_M = 4\hat{U}D_0(b). \tag*{(9)}

This property makes it possible to monitor the current of a bunched beam with an unsegmented Rogowski coil.

Small beam displacements can adequately be described by the linear term in Eq. (7), corresponding to m=1m = 1 in the sum. Thus, to lowest order

U0≈U^(ω)⋅[D0(b)+D1(b)⋅E1,0(x,y)]=U^(ω)⋅[1−1−b2b2Δθπ+2bπ(11−b2−1)x+yRt(cos⁡(θ)−sin⁡(θ))](10)\begin{aligned} U_0 \approx\hat{U}(\omega) \cdot[D_0(b) + D_1(b) \cdot E_{1,0}(x,y)] \\ &= \hat{U}(\omega) \cdot\left[\frac{1-\sqrt{1-b^2}}{b}\frac{2\Delta\theta}{\pi}+\frac{2}{b\pi}\left(\frac{1}{\sqrt{1-b^2}}-1\right)\frac{x+y}{R_t}\left(\cos(\theta)-\sin(\theta)\right)\right] \tag*{(10)} \end{aligned}

The linear term in the displacements xx, yy is the basis for the operation of opposed quadrants or halves as BPMs, if the corresponding signals are subtracted.

Frequency response

Before we discuss in § 2 the specifics of the design of a BPM based on a segmented toroidal Rogowski coil, the frequency response of such a system shall briefly be addressed. The basic setup of a toroidal coil that is split into four individual quadrants is shown in Figure 2. The equivalent circuit diagram for a single quadrant coil coupled to the beam circuit is depicted in Figure 3.

Figure 3. Equivalent circuit diagram for one toroidal coil quadrant with inductance LL, as shown in Figure 2. A voltage UMind(ω)U^{\mathrm{ind}}_M(\omega) is induced due to the inductive coupling of the beam inside the coil. The resistance of the quadrant coil is RR, and its capacitance CC is mostly due to the connecting wires. RoutR_{\mathrm{out}} represents the input impedance of the preamplifier.

The voltage UMU_M due to the induction by the orbiting bunched beam is modified by the resistance RR of the coil wire, by the inductance LL of the coil, and by the capacitance CC. The latter is mostly due to the connecting wires. The revolution frequency of the beam is low enough to treat these components as lumped elements, as shown in the equivalent circuit diagram in Figure 3. The resistor RoutR_{\mathrm{out}} describes the input impedance of the measuring device.

The lumped elements, CC, LL, RR, and RoutR_{\mathrm{out}} constitute a resonant circuit. Its frequency response F(ω)F(\omega) with the values given in Table I is calculated in Appendix B. This yields for a quarter coil an estimated resonant frequency of f0≈5.88 MHzf_0 \approx5.88\ \mathrm{MHz}.

One would ideally operate the coil quarters at resonance to take advantage of the amplified voltage in order to improve the signal-to-noise ratio. The disadvantage is that small shifts in the resonance frequency due to external conditions (e.g. temperature drifts) would lead to large changes in the amplifying factors of the four coils. Due to manufacturing tolerances the four resonance curves are not absolutely identical, which would therefore lead to changes in the position measurement. For this reason the decision was made to operate them off-resonance.

The Rogowski coils were designed for operation at a frequency of 3 MHz3\ \mathrm{MHz}, i.e. with four bunches orbiting in the storage ring at a revolution frequency of 750 kHz750\ \mathrm{kHz}. The final experiment was carried out in a single-bunch mode, thus calibrations and measurements were performed at 750 kHz750\ \mathrm{kHz}, i.e. far away from the resonance frequency. The resonant frequency of each coil was adjusted to match the revolution frequency of the beam by placing an appropriate capacitor in parallel to the coil.

ParameterValue
Number of quadrants MM4
Toroid large radiusRt=58.5 mmR_t = 58.5\ \mathrm{mm}
Toroid small radiusa=6.0 mma = 6.0\ \mathrm{mm}
Ratio parameterb=a/Rt=0.1026b = a/R_t = 0.1026
Wire diameterdw=450 μmd_w = 450\ \mu\mathrm{m}
Windings per quadrantNw=132N_w = 132
Angular coverageΔθ=64∘\Delta\theta= 64^\circ
Capacitance per quadrant (wiring)C≈20.7 pFC \approx20.7\ \mathrm{pF}
Inductance per quadrantL≈41.4 μHL \approx41.4\ \mu\mathrm{H}
Resistance of quarter coilR≈0.61 ΩR \approx0.61\ \Omega
Input impedanceRout≈500 kΩR_{\mathrm{out}} \approx500\ \mathrm{k}\Omega
Resonance frequency (estimated)f0≈5.88 MHzf_0 \approx5.88\ \mathrm{MHz}
Beam momentump=970 MeV/cp = 970\ \mathrm{MeV}/c
Revolution frequencyfrev=750 197.3 Hzf_{\mathrm{rev}} = 750\ 197.3\ \mathrm{Hz}
Lorentz factorβ=0.459\beta= 0.459
Number of stored particlesN=1×109N = 1 \times10^9
Corresponding beam currentI=eNfrev=120.2 μAI = eNf_{\mathrm{rev}} = 120.2\ \mu\mathrm{A}

Table 1. Parameters of the Rogowski coil design. The electrical parameters CC, LL, and RR are calculated in Appendix B. Typical beam parameters for a momentum pp are listed. ee denotes the elementary charge.

Experimental realization

Physical parameters of the Rogowski BPM

The Rogowski BPM described here consists of four equal coil segments, as illustrated in Figure 4, ⓐ. The four corresponding voltage signals of the preamplifiers[22] ⓕ can be combined electronically to yield the differential signals of two sets of opposing half coils, which serve to simultaneously determine the beam displacement in xx and in yy direction.

Image not extracted

Figure 4. Internal structure of the setup of the toroidal coil support in the test stand, depicted in Figure 6: ⓐ Toroidal quarter coils on torus, ⓑ coil supporting torus (PEEK), ⓒ coil support rings (PEEK), ⓓ DN 100/150 CF coil support flange ⓔ fiducial mark, ⓕ coaxial feedthrough with preamplifier, ⓖ DN 150 CF beam line vacuum tubes, ⓗ rotary flange, and ⓘ current carrying wire.

PEEK plastic (Polyether ether ketone, material properties are given in https://pubchem.ncbi.nlm.nih.gov/compound/19864017) was chosen as the material for the coil body, because of its low cost, good machineability and low outgassing rates in vacuum. The earlier used Vespel® material (For material properties, see https://www.dupont.com/products/vespel.html) proved worse in terms of price, and showed higher outgassing rates, mostly due to absorbed water. The coil body features both a groove along its outer circumference and small radial bore holes for the returning quarter coil wires and their fixation, respectively.

The inner and outer diameter of the toroid onto which the Rogowski coils are wound amount to 105 mm and 129 mm, respectively, sufficiently large to avoid any obstruction of the beam inside the circular beam tube diameter of 150 mm in the COSY straight sections. The Kapton-insulated copper wire for the sensor coils has a diameter of 450 μm\mu\mathrm{m}. The number of windings (Nw=132N_w = 132) determines the inductance of the quarter sensor coil and thus its resonant frequency, as discussed in Sec. II D. The calculated ohmic resistance of the coil is R≈0.61 ΩR \approx0.61\ \Omega. The inductance can be estimated from the textbook formula

of a straight coil with the same length, which yields a value of L≈41.4 μHL \approx41.4\ \mu\mathrm{H}.

To install the coil in the CF 160 flange, it is clamped between two PEEK rings held together by screws of the same material. Each coil features a twisted wire pair of 10 cm length followed by a 16 cm long SMA cable leading to an SMA feedthrough on a CF 16 flange. Figure 5 shows a photograph of the fully assembled BPM as it was used both on the test bench and in the storage ring.

Photograph of the Rogowski-BPM installed in the rotary flange

Figure 5. Photograph of the Rogowski-BPM installed in the rotary flange as shown in Figure 4. The coil covers an angle Δθ\Delta\theta. Note that Δθ+2θ=90∘\Delta\theta+ 2\theta= 90^\circ

Test stand for the Rogowski BPM

The laboratory test stand, shown in Figure 6, has been developed for the purpose of conditioning and calibrating Rogowski BPMs prior to the installation at COSY. The BPM is fixed on top of a stepper motor-driven xyxy-table ⓚ ⓛ in order to displace it laterally with respect to a current carrying tin-coated (corrosion-free) copper wire ⓘ, which mimics the particle beam in COSY. A sinusoidal current from a signal generator (Keysight 33522B Waveform Generator, Keysight Technologies, www.keysight.com) of about 100 μA\mu\mathrm{A} in amplitude represents the dominant Fourier component of the COSY beam current at the revolution frequency of 750 kHz. The wire of about 1 m length is fixed on one side in a xyxy-table ⓜ for angular adjustment and on the other side it is guided by a roll and pulled by a weight in a water bath nn to assure a constant tension on the wire without creating vibrations. It is terminated by a 50 Ω50\,\Omega resistor.

Image not extracted

Figure 6. Experimental setup to test and commission the Rogowski-type BPMs. The internal structure of the BPM is shown in Figure 4. ⓓ DN 100/150 CF coil support flange, ⓔ fiducial mark, ⓕ coaxial feedthrough with preamplifier, ⓖ DN 150 CF beam line vacuum tubes, ⓗ rotary flange of the rf Wien filter, ⓘ current carrying wire, ⓙ tool with knife edges and fiducial marks (see Figure 8), ⓚ vertical (yy) stepper-motor drive, ⓛ horizontal (xx) stepper-motor drive, ⓜ manual xyxy-table for angular adjustment of the current-carrying wire, and ⓝ weight in water bath to stretch the wire and to damp its oscillations.

Tubes gg on both sides of the flange are added to mimic the electrical surroundings of the BPM in COSY. The stepper motors kk ll (LIMES 150-100-MiSM-IMS produced by OWIS GmbH, www.owis.eu) move the coil in the xyxy-plane during a calibration measurement. They have a maximum travel range of 100 mm, a load capacity of 60 kg and a positioning error of <10 μm< 10\,\mu\mathrm{m}. The repeatability of a specific position is better than 500 nm, the resolution of 50 nm is limited by an encoder for each axis.

The analog signals from the coils are fed into custom-made preamplifiers[23] ff with gain factors of about 18, measured at 750 kHz. The amplified signals are analyzed by lock-in amplifiers (Zurich Instruments HF2LI Lock-in Amplifier 50 MHz, 210 MSa/s www.zhinst.com) using the TTL signals from a second signal generator of the same type as reference (Figure 7). This was necessary to avoid cross talk between the original signal and the reference signal when using two channels of the same device. Both generators were coupled to each other to assure that the generated frequencies were identical.

Image not extracted

Figure 7. Electric circuit diagram for the measurements with the experimental test setup as shown in Figure 6.

The analog-to-digital converters feature a resolution of 14 bit. A measurement bandwidth of 6.81 Hz with a fourth-order low-pass filter is typically used for signal processing. This entails a time constant of about 10 ms. The demodulator needs a 10 times larger time to reach 99% of the output level, which means that we are dealing with a minimum integration time of about 100 ms.

Calibration of the Rogowski BPM

For the relative calibration the device is moved relative to the current carrying wire using the stepper motors kk ll while the response of the quarter coils is processed by the readout electronics. A map is recorded covering the central part of the space inside the device (see Sec. IV C).

The absolute calibration is done using the insertion shown in Figure 8. This insertion was manufactured to determine the exact position of the wire during the calibration measurements. It consists of a structure which positions a knife edge j1j1 in the plane of the Rogowski torus bb and fiducial marks j2j2 to be used for a laser tracking system. The exact geometry was surveyed by a measuring machine (ZEISS UPMC850, Carl Zeiss QEC GmbH www.zeiss.de) to an accuracy of <1 μm< 1\,\mu\mathrm{m}. This insertion can be installed at any time making use of the slits in the discs without changing the position of the current wire. The wire ii is put at a voltage potential and a programmed routine moves the Rogowski BPM with the insertion until the wire touches the knife edge. Using the known geometry of the insert, the readings of the xyxy-tables and a laser tracker (OMNITRAC 2, Automated Precision Inc. www.apimetrology.com), the absolute position of the measured calibration maps can be connected to the fiducial marker ee located on top of the Rogowski BPM (see Figure 6) with an accuracy of <40 μm< 40\,\mu\mathrm{m}. After installation of the BPM in COSY the position of the fiducial mark is determined within the COSY lattice using a laser tracker. Thus the absolute position of the particle beam within the COSY lattice can be determined with an accuracy defined by the accuracy of the measurement of the laser tracker, which is about 50 to 100 μm\mu\mathrm{m}.

Figure 8. Knife edge tool with knife edges j1 and fiducial marks j2, quarter coils a wound on the torus b. The current carrying wire is denoted by i.

Vacuum compatibility

Besides the accuracy of the position measurement, the compatibility with the vacuum standards of the accelerator is crucial. All components of the Rogowski coil were cleaned and baked before assembly. In order to test the vacuum compatibility before installation in the accelerator, a vacuum test stand was set up, which consists of a bakeable chamber that is pumped by a 250 l/s turbomolecular pump (comparable to the pumping speed at the installation point in the accelerator). A quadrupole mass analyzer was used to determine the composition of the rest gas in the chamber.

The use of PEEK as material for the coil body and the Kapton coated wire for the coils yielded small outgassing rates. The pressures reached after baking at 120 °C for a week are <5×10−9< 5 \times10^{-9} mbar. The mass spectrum before baking showed a dominant water peak. After baking the water is removed from the structure and the wire. To minimize water accumulation on the BPM during installation in the ring, the time it was exposed to air was minimized.

Attention was paid to the temperature during the baking process, as this takes place after the calibration of the coil (which was carried out in air, see § 2 C and Figure 6). The reason for this is that both the Kapton-coated wire and the PEEK plastic adsorb water in air. To ensure that baking did not alter the calibration values, several test calibrations were carried out before and after baking, which showed that there was no difference in the calibration values within previously mentioned accuracy.

Investigations using the test stand

Impedance measurement of a quarter coil

In order to characterize one quarter coil according to the circuit diagram of Figure 3 an impedance measurement was performed using a network analyzer (Siglent SVA 1032X, SIGLENT Technologies www.siglenteu.com).

The influence of the connection cable outside the vacuum vessel was taken into account in the calibration, so that the results, shown in Figure 9 represent the coil with the connection wires up to the vacuum flange (see Figure 4). The preamplifier was not used for this measurement. The impedance of the coil can be expressed by

Figure 9. Combined fit to the amplitude and phase data from the network analyzer according to Eq. (11).

Z(ω)=(iωC+1R+iωL)−1(11)Z(\omega) = \left(i\omega C + \frac{1}{R+i\omega L}\right)^{-1} \tag*{(11)}

where RR, LL and CC are the respective properties of the circuit, shown in Figure 3. The amplitude and phase of Eq. (11) were used in a combined fit to determine these properties (Figure 9). To improve the fit an additional offset of the phase, was introduced as a parameter. The value amounts to −2.9(1)-2.9(1) degrees. For the amplitude ∣Z∣\lvert Z\rvert relative error of 5% was assumed, for the phase arg⁡(Z)\arg(Z) the assumed error is 1 degree. These errors were estimated from the RMS of several measurements at the same frequency. The overall χ2\chi^2 is 540. The amplitude contributes with 85 and the phase plot with 455 to the χ2\chi^2 value. The number of degrees of freedom is 160 (data points) - 4 (parameters) = 156. A possible correlation between amplitude and phase data is not taken into account. The resulting properties are the ohmic resistance R=4.88(9) ΩR = 4.88(9)\ \Omega, the inductance L=34.27(41) μHL = 34.27(41)\ \mu\mathrm{H} and the capacitance C=39.26(47) pFC = 39.26(47)\ \mathrm{pF}. The DC resistance of the coil was measured to be about 1 Ω\Omega. For a copper wire used in the experiment due to the skin effect one expects an ohmic resistance increase by a factor of 4, roughly in agreement with the fit parameters.

Measurement of resonant behavior of a quarter coil

The resonant behaviour of a quarter coil was measured on the test setup, shown in Figure 6 using a wire to mimic the beam current. The induced current in the four coils were amplified and analyzed in lock-in amplifiers (see § 2 B). The result for one quarter coil is shown in Figure 10. The amplitude and phase are given by Eqs. (43) and (B3).

Image not extracted

Figure 10. Combined fit to the amplitude and phase data of one Rogowski coil excited by the current-carrying wire on the test stand.

To better fit the data, the heuristic parameters sps_p, sRs_R and ϕ0\phi_0 were introduced, yielding

U~M(ω)=(1+sUω)F(Rout,L,C,R′,I,ω)UMind(12)\widetilde{U}_M(\omega) = (1 + s_U\omega)F(R_{\mathrm{out}},L,C,R',I,\omega)U_M^{\mathrm{ind}} \tag*{(12)}

where

R′=R(1+sR(ω−ω0))(13)R' = R(1+s_R(\omega-\omega_0)) \tag*{(13)}
ϕ′(ω)=(1+spω)ϕ−ϕ0.(14)\phi'(\omega) = (1+s_p\omega)\phi-\phi_0 . \tag*{(14)}

These additional parameters account for other resonances present in the system and for the skin/proximity effect[24]. Due to the strong correlation between CC and LL, the value of LL was fixed to the value from the impedance fit. An

TABLE II. Parameters of the fit to the resonance data in Figure 10.

input impedance of the preamplifiers of Rout=500 kΩR_{\mathrm{out}}=500\ \mathrm{k\Omega} was assumed. The results are summarized in Table II.

Fit ParameterValue
RR7.798(45) Ω7.798(45)\ \Omega
LL fixed34.27 μH34.27\ \mathrm{\mu H}
CC69.401(5) pF69.401(5)\ \mathrm{pF}
RoutR_{\mathrm{out}} fixed500 kΩ500\ \mathrm{k\Omega}
UMindU_M^{\mathrm{ind}}9.12(1) mV9.12(1)\ \mathrm{mV}
sUs_U8.0(2)×10−8 s−18.0(2)\times10^{-8}\ \mathrm{s}^{-1}
sps_p−2.4(2)×10−8 s−1-2.4(2)\times10^{-8}\ \mathrm{s}^{-1}
sRs_R8.3(4)×10−7 s−18.3(4)\times10^{-7}\ \mathrm{s}^{-1}
ϕ0\phi_0152.5(2) degree152.5(2)\ \mathrm{degree}

Table II.

For the U~M\widetilde{U}_M a relative error of 1% was assumed, for the phase the assumed error is 1 degree. The χ2\chi^2 is 52.4 and has a contribution of 16.3 from the amplitude and 36.1 from the phase. The number of degrees of freedom is 2⋅58(bins)−7(parameters)=1092\cdot58(\mathrm{bins})-7(\mathrm{parameters})=109.

The equivalent circuit of Figure 3, together with the additional parameters discussed above, describes the data very well. The increased resistance RR and capacitance CC compared to the impedance measurement are due to the preamplifier.

It was noticed that due to manufacturing tolerances the resonance curves slightly differed for the four coils. This resulted in a strong frequency dependence of the calibration. To reduce this effect variable capacitors were installed, which shifted the resonance frequencies of all coils to a common value.

Calibration measurement of the BPM

The calibration measurement was carried out as described in § 2 C. A map of 21×21=44121\times21=441 points is measured in the xyxy-plane in the range ±10 mm\pm10\ \mathrm{mm}. The four voltages UMU_M of Eqs. (7), (8) were recorded and processed as follows. We define:

UΔx=U0−U1−U2+U3,UΔy=U0+U1−U2−U3.(15)U^{\Delta x}=U_0-U_1-U_2+U_3,\qquad U^{\Delta y}=U_0+U_1-U_2-U_3. \tag*{(15)}

Using UΣU^\Sigma from Eq. (9), the ratios UΔx/UΣU^{\Delta x}/U^\Sigma and UΔy/UΣU^{\Delta y}/U^\Sigma are shown as a function of xx and yy, respectively, in Figure 11. For better visibility of the data the graphs are shifted proportionally by the respective yy and xx values. The first order linear behavior clearly dominates. To get a good description of the data by the theory additional parameters were introduced: The fit includes terms up to 4th order in mm (see Appendix A). Despite of the clamping mechanism of the torus a perfect alignment angle could not be guaranteed, therefore an angle α\alpha was added by which the xyxy-coordinate system of the coils was rotated around the zz-axis. The coils themselves are not exactly equal, therefore small relative scaling coefficients (1+Csc)(1+C_{sc}) for the voltages for three of the coils with respect to the fourth were introduced. From the RMS of repeated measurements the error on UΔx,y/UΣU^{\Delta x,y}/U^{\Sigma} was estimated to be 2⋅10−42\cdot10^{-4}. With this error assumption a χ2\chi^2-minimization resulted in χ2\chi^2 values of 19.5 and 7.5 for the ratios UΔx/UΣU^{\Delta x}/U^{\Sigma} and UΔy/UΣU^{\Delta y}/U^{\Sigma}, respectively, for 441 (measurement points) −- 20 (parameters) == 421 degrees of freedom (ndf). The low χ2\chi^2/ndf indicates that the errors on UΔx,y/UΣU^{\Delta x,y}/U^{\Sigma} were probably overestimated.

Figure 11. Calibration map with the measured UΔx/UΣU^{\Delta x}/U^{\Sigma} and UΔy/UΣU^{\Delta y}/U^{\Sigma} values depending on the respective xx and yy positions set with the stepping drives of the xyxy-table. For better visibility the graphs are shifted by the respective yy and xx values.

From the fitted parameters to model UΔx,y/UΣU^{\Delta x,y}/U^{\Sigma}, one can now reconstruct xx and yy and compare it with selected xx and yy values. This is shown in Figure 12. The residuals (reconstructed - selected) are of the order of few μ\mum.

Figure 12. Residuals: reconstructed xx − selected xx vs. xx (top) and reconstructed yy − selected yy vs. yy (bottom).

The linear coefficient c1c_1 of Figure 11 can be derived from Eqs. (8) - (10) to:

c1=D1E1D01x+y=1Rt1−b2cos⁡(θ)−sin⁡(θ)Δθ≈0.0115 mm−1,(16)\begin{aligned} c_1 &= \frac{D_1E_1}{D_0}\frac{1}{x+y}\\ &= \frac{1}{R_t\sqrt{1-b^2}}\frac{\cos(\theta)-\sin(\theta)}{\Delta\theta}\\ &\approx0.0115\ \mathrm{mm}^{-1}, \tag*{(16)} \end{aligned}

but the fitted values c1fit≈0.018 mm−1c_1^{\mathrm{fit}}\approx0.018\ \mathrm{mm}^{-1}, which could also be estimated directly from Figure 11, are substantially higher. This originates in the surrounding of the coil.

c1c_1 was calculated for an air coil in an environment free of conducting material. Since the Rogowski coils are installed inside the beam tube (Figure 4) secondary induction due to mirror currents on the inner surface of the beam tube needs to be considered. This effect is included in the coefficient (see Appendix C, eq. (C8))

c1′=c1(1+b2Rt22u2bπD1(b))≈c1(1+Rt22u2)≈0.015 mm−1(17)c'_1=c_1\left(1+\frac{b^2R_t^2}{2u^2b\pi D_1(b)}\right) \approx c_1\left(1+\frac{R_t^2}{2u^2}\right)\approx0.015\ \mathrm{mm}^{-1} \tag*{(17)}

with the inner radius of the beam pipe u=76.5u=76.5 mm. This estimate is based on the simple geometry of a straight beam tube and explains qualitatively the difference between the fitted value and the calculated value of an air coil in Eq. 16.

Figure 14. UΔy/UΣU^{\Delta y}/U^{\Sigma} before (a) and after (b) offset correction. Without the correction a drift depending on the beam current was observed in contrast to the measurements in the laboratory. The offset correction eliminates this dependence.

Installation at COSY

After the calibration (Sec. IV C) and baking procedure (§ 2 D) the coil was installed at the storage ring COSY. It was noticed that an additional offset voltage present at zero beam current appeared. This offset disturbed the position measurements, so that the position readings depended on the beam current, as shown in Figure 13a and 14a. The offset is due to stray fields of the COSY cavity which is located at a distance of 9 m from the Rogowski coils. The cavity is defining the COSY revolution frequency which is also used as a reference frequency of the lock-in amplifier.

Figure 13. UΔx/UΣU^{\Delta x}/U^{\Sigma} before (a) and after (b) offset correction. Without the correction a drift depending on the beam current was observed in contrast to the measurements in the laboratory. The offset correction eliminates this dependence.

The offset was determined by extrapolating the measured voltages to zero beam current as can be seen for U0U_0 in Figure 15. The interception of the straight line fit with the vertical axis yields the respective voltage offset corrections U0off=775.4 μVU_0^{\mathrm{off}} = 775.4\,\mathrm{\mu V}, U1off=749.5 μVU_1^{\mathrm{off}} = 749.5\,\mathrm{\mu V}, U2off=718.2 μVU_2^{\mathrm{off}} = 718.2\,\mathrm{\mu V}, U3off=706.5 μVU_3^{\mathrm{off}} = 706.5\,\mathrm{\mu V}. The subtraction of these offset values from the measured voltages resulted in beam current independent position values as expected from the calibration measurements in the laboratory (Figure 13b and 14b). Note that a change of 10−410^{-4} in the voltage ratio as shown in these figures corresponds to a change in position of 10−4/c1fit=10−4/0.018 μm≈5.5 μm10^{-4}/c_1^{\mathrm{fit}} = 10^{-4}/0.018\,\mathrm{\mu m} \approx5.5\,\mathrm{\mu m}. It can be seen that the error on a single measurement of a 1 s time interval is also of a similar amount, corresponding to a resolution of 5 μm\mathrm{\mu m}.

Figure 15. Example of the induced voltage U0U_0 as a function of the COSY beam current II. The additional offset, due to stray fields, was determined by extrapolation to zero beam current.

The Rogowski BPM was used during several experimental beam times by the JEDI collaboration in order to determine the position of the COSY deuteron beam. Figures 16 show the measured beam position in horizontal and vertical direction for five consecutive cycles for the Rogowski coil (52x, 52y) and a conventional COSY BPM (6x, 6y).

Conclusion and outlook

We described the development of a new type of beam position monitor based on a Rogowski coil. It reaches a resolution of 5 μm\mathrm{\mu m} in 1 s time interval. The absolute accuracy is determined by the alignment accuracy of about 50 μm\mathrm{\mu m}. One advantage over classical capacitive BPMs is the short insertion length of these devices. In an energy-variable machine, the frequency-dependent amplification of the Rogowski BPMs limits its sensitivity, because away from the resonance the amplitude decreases. In the specific case of a fixed-energy EDM machine, however, this presents an advantage because, with optimized design, the resonance amplifies the signals.

While our development uses four toroidal coils, in principle, the device could be divided into more segments in order to study higher-order components of the transverse particle beam distribution. Note that with the four-fold segmentation presented here a quadrupole component could already be studied. A pair of higher segmented Rogowski coils at a distance in the storage ring may offer the possibility to measure the phase space distribution of the particle beam. The individual quarter coils have been measured separately in our investigations to yield the required differential voltage electronically after subtraction. A better read out scheme may be established by a direct galvanic connection between opposing quarters in order to inherently be sensitive to the differential signal without having to deal with the dominant contribution of the beam current represented by the term D0(b)D_0(b) in Eq. (10). This may also entail the development of a dedicated pre-amplifier for this purpose. Also, the cross talk between neighboring coils due to the induced currents can be reduced.

Acknowledgments

This work has been performed in the framework of the JEDI collaboration, and is financially supported by an ERC Advanced-Grant (srEDM # 694390) of the European Union.

We are very grateful to Jürgen Böker, Hans-Joachim Krause, Stefan Hintzen, Andrea Pesce, Thomas Sefzick and Jamal Slim for their support.

Figure 16. Measured horizontal (52x) and vertical beam positions (52y) during five consecutive cycles in COSY. For comparison the horizontal (vertical) position measurement of the next conventional COSY BPM (6x,6y) 4 m downstream in beam direction is shown. The lower plots show the beam current. Note that the drifts are in opposite directions which is caused by quadrupole magnets in between the two devices.

Detailed derivations

Involving Stokes’ theorem, the calculation of the magnetic flux due to the beam current enclosed by the winding surfaces SS of a quarter coil with index M=0,1,2,3M = 0, 1, 2, 3 can be expressed by the line integral of the vector potential over the boundary ∂S\partial S of the surface SS,

Φ=∬SB⃗⋅dS⃗=∮∂SA⃗⋅dℓ⃗.(18)\Phi= \iint_S \vec{B} \cdot\mathrm{d}\vec{S} = \oint_{\partial S} \vec{A} \cdot\mathrm{d}\vec{\ell}. \tag*{(18)}

The approach using the vector potential seems to be advantageous compared to the use of the BB-field, because in this case, we only have to deal with the single component AzA_z in order to obtain the enclosed magnetic flux. Furthermore, via Stokes’ theorem, one integration less is required.

Derivation of magnetic flux induced in a quadrant coil

The surface of the torus with given values for RtR_t and aa, as shown in Figure 17, is parameterized in terms of the two angles φ\varphi and β\beta according to

ℓ⃗=(ℓx(β,φ)ℓy(β,φ)ℓz(β))=((Rt+acos⁡β)⋅cos⁡φ(Rt+acos⁡β)⋅sin⁡φasin⁡β).(19)\vec{\ell} = \begin{pmatrix} \ell_x(\beta,\varphi) \\ \ell_y(\beta,\varphi) \\ \ell_z(\beta) \end{pmatrix} = \begin{pmatrix} (R_t+a\cos\beta)\cdot\cos\varphi\\ (R_t+a\cos\beta)\cdot\sin\varphi\\ a\sin\beta \end{pmatrix}. \tag*{(19)}

The wire does not cover the surface of the torus entirely but follows a path given by a linear relation between the two angles φ\varphi and β\beta

φ(β)=u⋅β.(20)\varphi(\beta)=u\cdot\beta. \tag*{(20)}

Due to the fact that the vector potential has only a component along the zz-direction, we only need the zz-component of the differential line element dℓ⃗\mathrm{d}\vec{\ell} along the coil winding, which is obtained by differentiation

dℓz(β)=acos⁡β dβ.(21)\mathrm{d}\ell_z(\beta)=a\cos\beta\,\mathrm{d}\beta. \tag*{(21)}

Furthermore one has to consider that the coils do not cover the full torus. The angles involved are indicated in Figure 5.

The integral in Eq. (18) can be further simplified, yielding for the flux induced in a quadrant MM,

ΦM(x,y)=∮A⃗⋅dℓ⃗=∫Az(ρ(β),φ(β)) dℓz=a∫02π⋅NwAz(ρ(β),φ(β))cos⁡β dβ=a2Nwπ∫M(π/2)+θ(M+1)(π/2)−θ∫02πAz(ρ(β),φ)cos⁡β dβ dφ.(22)\begin{aligned} \Phi_M(x,y) &= \oint\vec{A}\cdot\mathrm{d}\vec{\ell} = \int A_z(\rho(\beta),\varphi(\beta))\,\mathrm{d}\ell_z \\ &= a\int_0^{2\pi\cdot N_w} A_z(\rho(\beta),\varphi(\beta))\cos\beta\,\mathrm{d}\beta\\ &= a\frac{2N_w}{\pi}\int_{M(\pi/2)+\theta}^{(M+1)(\pi/2)-\theta}\int_0^{2\pi} A_z(\rho(\beta),\varphi)\cos\beta\,\mathrm{d}\beta\,\mathrm{d}\varphi. \tag*{(22)} \end{aligned}

where

ρ(β)=Rt+acos⁡β=Rt(1+bcos⁡β),(23)\rho(\beta)=R_t+a\cos\beta=R_t(1+b\cos\beta), \tag*{(23)}

as shown in Figure 17. In the last line of Eq. (22), the sum over the NwN_w discrete angle values of φ\varphi is represented by an integral, which is an adequate description for a densely wound coil. In cylindrical coordinates, the vector potential Az(ρ,φ)A_z(\rho,\varphi) has already been introduced in Eq. (5), in which the beam displacement from the center is parameterised in cylindrical coordinates

x=rcos⁡ψandy=rsin⁡ψ.(24)x=r\cos\psi\quad\text{and} \quad y=r\sin\psi. \tag*{(24)}

Eq. (5) can be written as

Az(ρ,φ)=−μ0I2πln⁡ρ2−2ρrcos⁡(φ−ψ)+r2=−μ0I2π[ln⁡ρ−∑m=1∞1m(rρ)mcos⁡[m(φ−ψ)]].(25)\begin{aligned} A_z(\rho,\varphi) &=-\frac{\mu_0 I}{2\pi}\ln\sqrt{\rho^2-2\rho r\cos(\varphi-\psi)+r^2} \\ &=-\frac{\mu_0 I}{2\pi}\left[\ln\rho-\sum_{m=1}^{\infty}\frac{1}{m}\left(\frac{r}{\rho}\right)^m\cos\left[m(\varphi-\psi)\right]\right]. \tag*{(25)} \end{aligned}

where the latter part describes the decomposition into a Fourier series[25] (Eq. 3.152), for r<ρr<\rho. For a beam current monitor without segmentation of the toroidal coil, the integration over φ\varphi must be performed from 00 to 2π2\pi.

Eq. (25) shows that all the cosine terms yield vanishing contributions in this case. Therefore, the information about the beam displacement encoded in ψ\psi (see Eq. (24)) vanishes as well. A full Rogowski coil without segmentation therefore constitutes a beam current monitor, its sensitivity being entirely described by the last logarithmic term in Eq. (25), which depends only on the coil geometry. For a toroidal coil segmented into four quadrants MM, each covering Δθ≈64∘\Delta\theta\approx64^\circ, however, the first integration over φ\varphi required in Eq. (22) yields

Az(1)(ρ,M)=2Nwπ∫M(π/2)+θ(M+1)(π/2)−θAz(ρ,φ) dφ=−μ0NwIπ2[Δθln⁡(ρ)−∑m=1∞1m(rρ)m(∫M(π/2)+θ(M+1)(π/2)−θcos⁡(mφ) dφ⋅cos⁡(mψ)+∫M(π/2)+θ(M+1)(π/2)−θsin⁡(mφ) dφ⋅sin⁡(mψ))]=−μ0NwIπ2[Δθln⁡ρ−∑m=1∞1m2(rρ)m(cm,Mcos⁡(mψ)+dm,Msin⁡(mψ))].(26)\begin{aligned} A_z^{(1)}(\rho,M)=\frac{2N_{\mathrm{w}}}{\pi}\int_{M(\pi/2)+\theta}^{(M+1)(\pi/2)-\theta} A_z(\rho,\varphi)\,\mathrm{d}\varphi\\ &=-\frac{\mu_0N_{\mathrm{w}}I}{\pi^2}\left[\Delta\theta\ln(\rho)-\sum_{m=1}^{\infty}\frac{1}{m}\left(\frac{r}{\rho}\right)^m\left(\int_{M(\pi/2)+\theta}^{(M+1)(\pi/2)-\theta}\cos(m\varphi)\,\mathrm{d}\varphi\cdot\cos(m\psi)+\int_{M(\pi/2)+\theta}^{(M+1)(\pi/2)-\theta}\sin(m\varphi)\,\mathrm{d}\varphi\cdot\sin(m\psi)\right)\right] \\ &=-\frac{\mu_0N_{\mathrm{w}}I}{\pi^2}\left[\Delta\theta\ln\rho-\sum_{m=1}^{\infty}\frac{1}{m^2}\left(\frac{r}{\rho}\right)^m\left(c_{m,M}\cos(m\psi)+d_{m,M}\sin(m\psi)\right)\right]. \tag*{(26)} \end{aligned}

where the coefficients

cm,M=sin⁡(mπM+12−θ)−sin⁡(mπM2+θ)(27)c_{m,M}=\sin\left(m\pi\frac{M+1}{2}-\theta\right)-\sin\left(m\pi\frac{M}{2}+\theta\right) \tag*{(27)}
dm,M=−cos⁡(mπM+12−θ)+cos⁡(mπM2+θ).d_{m,M}=-\cos\left(m\pi\frac{M+1}{2}-\theta\right)+\cos\left(m\pi\frac{M}{2}+\theta\right).

are functions of the angle θ\theta (see Table III). The dependence on mm of the arguments of the trigonometric functions can be eliminated using a sum over the sine and cosine functions, related to the beam displacements xx and yy, via Eq. (24). It follows with these trigonometric relations from [26] (1.331-1 and 1.331-3) that

Az(1)(ρ,M)=−μ0NwIπ2[Δθln⁡ρ−∑m=1∞1m2(rρ)m(cm,M∑n=0⌊m/2⌋(m2n)(cos⁡ψ)m−2n(sin⁡ψ)2n(−1)n+dm,M∑n=0⌊(m−1)/2⌋(m2n+1)(cos⁡ψ)m−(2n+1)(sin⁡ψ)2n+1(−1)n)].(28)A_z^{(1)}(\rho,M)=-\frac{\mu_0N_{\mathrm{w}}I}{\pi^2}\left[\Delta\theta\ln\rho-\sum_{m=1}^{\infty}\frac{1}{m^2}\left(\frac{r}{\rho}\right)^m\left(c_{m,M}\sum_{n=0}^{\lfloor m/2\rfloor}\binom{m}{2n}(\cos\psi)^{m-2n}(\sin\psi)^{2n}(-1)^n+d_{m,M}\sum_{n=0}^{\lfloor(m-1)/2\rfloor}\binom{m}{2n+1}(\cos\psi)^{m-(2n+1)}(\sin\psi)^{2n+1}(-1)^n\right)\right]. \tag*{(28)}

where, e.g., ⌊m⌋≡floor⁡(m)\lfloor m\rfloor\equiv\operatorname{floor}(m). In terms of the displacements, parameterized using Eq. (24), one can then write

Az(1)(ρ,M)=−μ0NwIπ2[Δθln⁡ρ−∑m=1∞1m2(Rtρ)m(cm,M∑n=0⌊m/2⌋(m2n)(xRt)m−2n(yRt)2n(−1)n+dm,M∑n=0⌊(m−1)/2⌋(m2n+1)(xRt)m−(2n+1)(yRt)2n+1(−1)n)].(29)A_z^{(1)}(\rho,M)=-\frac{\mu_0N_{\mathrm{w}}I}{\pi^2}\left[\Delta\theta\ln\rho-\sum_{m=1}^{\infty}\frac{1}{m^2}\left(\frac{R_t}{\rho}\right)^m\left(c_{m,M}\sum_{n=0}^{\lfloor m/2\rfloor}\binom{m}{2n}\left(\frac{x}{R_t}\right)^{m-2n}\left(\frac{y}{R_t}\right)^{2n}(-1)^n+d_{m,M}\sum_{n=0}^{\lfloor(m-1)/2\rfloor}\binom{m}{2n+1}\left(\frac{x}{R_t}\right)^{m-(2n+1)}\left(\frac{y}{R_t}\right)^{2n+1}(-1)^n\right)\right]. \tag*{(29)}

The missing integration over β\beta according to Eq. (22), taking into account Eq. (23), yields the magnetic flux

ΦM(x,y)=a∫02πAz(1)(Rt+acos⁡β,M)cos⁡β dβ=−μ0NwIaπ2[ΔθA(2)−∑m=1∞1m2∫02π(RtRt+acos⁡β)mcos⁡β dβ⋅Em,M(x,y)].(30)\begin{aligned} \Phi_M(x,y)=a\int_0^{2\pi} A_z^{(1)}(R_t+a\cos\beta,M)\cos\beta\,\mathrm{d}\beta\\ &=-\frac{\mu_0N_wI_a}{\pi^2}\left[\Delta\theta A^{(2)}-\sum_{m=1}^{\infty}\frac{1}{m^2}\int_0^{2\pi}\left(\frac{R_t}{R_t+a\cos\beta}\right)^m\cos\beta\,\mathrm{d}\beta\cdot E_{m,M}(x,y)\right]. \tag*{(30)} \end{aligned}

The position-dependent functions Em,M(x,y)E_{m,M}(x,y) are defined below in Eq. (A19). The integral in Eq. (A13) can be solved by partial integration and the use of reference[26] (3.644-4).

A(2)=∫02πln⁡(Rt+acos⁡β)cos⁡β dβ=∫02πbsin⁡2β1+bcos⁡β dβ=2πb(1−1−b2),(31)\begin{aligned} A^{(2)}=\int_0^{2\pi}\ln(R_t+a\cos\beta)\cos\beta\,\mathrm{d}\beta\\ &=\int_0^{2\pi}\frac{b\sin^2\beta}{1+b\cos\beta}\,\mathrm{d}\beta=\frac{2\pi}{b}\left(1-\sqrt{1-b^2}\right), \tag*{(31)} \end{aligned}

with b=a/Rtb=a/R_t.

The induced flux in segment MM can be written as

ΦM(x,y)=−μ0NwIa[1−1−b2b2Δθπ−∑m=1∞Cm(b)(mπ)2(cm,M∑n=0⌊m/2⌋(m2n)(xRt)m−2n(yRt)2n(−1)n+dm,M∑n=0⌊(m−1)/2⌋(m2n+1)(xRt)m−(2n+1)(yRt)2n+1(−1)n)].(32)\Phi_M(x,y)=-\mu_0N_wI_a\left[\frac{1-\sqrt{1-b^2}}{b}\frac{2\Delta\theta}{\pi}-\sum_{m=1}^{\infty}\frac{C_m(b)}{(m\pi)^2}\left(c_{m,M}\sum_{n=0}^{\lfloor m/2\rfloor}\binom{m}{2n}\left(\frac{x}{R_t}\right)^{m-2n}\left(\frac{y}{R_t}\right)^{2n}(-1)^n+d_{m,M}\sum_{n=0}^{\lfloor(m-1)/2\rfloor}\binom{m}{2n+1}\left(\frac{x}{R_t}\right)^{m-(2n+1)}\left(\frac{y}{R_t}\right)^{2n+1}(-1)^n\right)\right]. \tag*{(32)}

The remaining integral in Eq. (A15),

Cm(b)=∫02πcos⁡β(1+bcos⁡β)m dβ,(33)C_m(b)=\int_0^{2\pi}\frac{\cos\beta}{(1+b\cos\beta)^m}\,\mathrm{d}\beta, \tag*{(33)}

is required for m≥1m\ge1 and can be evaluated by recursion, as explained in Sec. A 2.

With the substitutions

D0(b)=1−1−b2b2Δθπ,D_0(b)=\frac{1-\sqrt{1-b^2}}{b}\frac{2\Delta\theta}{\pi},
Dm(b)=−Cm(b)(mπ)2for m=1,2,3,…,(34)D_m(b)=-\frac{C_m(b)}{(m\pi)^2}\quad\text{for }m=1,2,3,\ldots, \tag*{(34)}

the induced flux in quadrant MM can be written as

ΦM(x,y)=−μ0NwIa[D0(b)+∑m=1∞Dm(b)Em,M(x,y)].(35)\Phi_M(x,y)=-\mu_0N_wI_a\left[D_0(b)+\sum_{m=1}^{\infty}D_m(b)E_{m,M}(x,y)\right]. \tag*{(35)}

The position-dependent terms Em,M(x,y)E_{m,M}(x,y) are given by

Em,M(x,y)=cm,M∑n=0⌊m/2⌋(m2n)(xRt)m−2n(yRt)2n(−1)n+dm,M∑n=0⌊(m−1)/2⌋(m2n+1)(xRt)m−(2n+1)(yRt)2n+1(−1)n.(36)E_{m,M}(x,y)=c_{m,M}\sum_{n=0}^{\lfloor m/2\rfloor}\binom{m}{2n}\left(\frac{x}{R_t}\right)^{m-2n}\left(\frac{y}{R_t}\right)^{2n}(-1)^n+d_{m,M}\sum_{n=0}^{\lfloor(m-1)/2\rfloor}\binom{m}{2n+1}\left(\frac{x}{R_t}\right)^{m-(2n+1)}\left(\frac{y}{R_t}\right)^{2n+1}(-1)^n. \tag*{(36)}

Analytic expressions for the functions Dm(b)D_m(b) and the coefficients cm,Mc_{m,M} and dm,Md_{m,M} are listed in Table III, and for the functions Em,M(x,y)E_{m,M}(x,y) in Table IV, up to order m=6m=6.

The symmetry relations for the Em,M(x,y)E_{m,M}(x,y) in the different quadrants MM, given in Table IV, apply to all orders in mm and are passed on to the induced magnetic flux in a quadrant. Thus, given a magnetic flux in quadrant M=0M=0 of Φ0(x,y)\Phi_0(x,y), one can write for the induced fluxes in the other quadrants,

Φ1(x,y)=Φ0(−x,y),Φ2(x,y)=Φ0(−x,−y),Φ3(x,y)=Φ0(x,−y).(37)\begin{aligned} \Phi_1(x,y)&=\Phi_0(-x,y),\\ \Phi_2(x,y)&=\Phi_0(-x,-y),\\ \Phi_3(x,y)&=\Phi_0(x,-y). \tag*{(37)} \end{aligned}

Please note the equivalence to Eq. (8).

Recursion formula for Cm(b)C_m(b)

The difference of two consecutive functions is found to be proportional to the derivative of the first one.

Cm+1(b)−Cm(b)=∫02πcos⁡β(1+bcos⁡β)m(11+bcos⁡β−1) dβ=−b∫02πcos⁡2β(1+bcos⁡β)m+1 dβ=bmddbCm(b).(38)\begin{aligned} C_{m+1}(b)-C_m(b) &=\int_0^{2\pi}\frac{\cos\beta}{(1+b\cos\beta)^m}\left(\frac{1}{1+b\cos\beta}-1\right)\,\mathrm{d}\beta\\ &=-b\int_0^{2\pi}\frac{\cos^2\beta}{(1+b\cos\beta)^{m+1}}\,\mathrm{d}\beta =\frac{b}{m}\frac{\mathrm{d}}{\mathrm{d}b}C_m(b). \tag*{(38)} \end{aligned}

Thus, the (m+1)(m+1)-th function can be obtained from the mm-th function by recursion via

Cm+1(b)=Cm(b)+bmddbCm(b),(39)C_{m+1}(b)=C_m(b)+\frac{b}{m}\frac{\mathrm{d}}{\mathrm{d}b}C_m(b), \tag*{(39)}

where, following Eq. (A16), for b∈(−1,1)b\in(-1,1) the function starting the recursion is found to be

C1(b)=∫0π2cos⁡β1+bcos⁡β dβ=2πb(1−11−b2).(40)C_1(b)=\int_0^\pi\frac{2\cos\beta}{1+b\cos\beta}\,\mathrm{d}\beta =\frac{2\pi}{b}\left(1-\frac{1}{\sqrt{1-b^2}}\right). \tag*{(40)}

Magnetic flux in one quadrant without displacement

Without displacements of the beam with respect to the center of the toroidal coil, i.e., for x=y=0x=y=0, the magnetic flux in Eq. (A18) is entirely given by the first term, yielding the well-known result

ΦM(r=0)=−μ0NwIaD0(b)≈−μ0NwIab2=−Nw⋅μ0I2πRt⋅πa2=−Nw⋅B⋅S,(41)\begin{aligned} \Phi_M(r=0)&=-\mu_0N_wI_aD_0(b)\\ &\approx-\mu_0N_wI_a\frac{b}{2}\\ &=-N_w\cdot\frac{\mu_0I}{2\pi R_t}\cdot\pi a^2=-N_w\cdot B\cdot S, \tag*{(41)} \end{aligned}

that the magnetic flux is equal to the product of the number of coil windings NwN_w, magnetic flux density BB at a distance of RtR_t and the enclosed winding area SS. (In the second line, we have made use of the fact that b≪1b\ll1, see Table I.)

Resonance frequency of quarter toroid

The numerical calculation of the resonance frequency is carried out using the equivalent circuit diagram shown in Figure 3. The relation of the measured output voltage UMU_M to the beam induced voltage UMindU_M^{\mathrm{ind}} can be described in the frequency domain using the picture of a voltage divider, which leads to

UMUMind=(1Rout+iωC)−1iωL+R+(1Rout+iωC)−1=1(iωL+R)(1Rout+iωC)+1.(42)\frac{U_M}{U_M^{\mathrm{ind}}} =\frac{\left(\frac{1}{R_{\mathrm{out}}}+i\omega C\right)^{-1}}{i\omega L+R+\left(\frac{1}{R_{\mathrm{out}}}+i\omega C\right)^{-1}} =\frac{1}{(i\omega L+R)\left(\frac{1}{R_{\mathrm{out}}}+i\omega C\right)+1}. \tag*{(42)}

The amplitude can be written as

F(ω)=∣UMUMind∣=1(1−ω2LC+RRout)2+(ωLRout+ωRC)2.(43)F(\omega)=\left|\frac{U_M}{U_M^{\mathrm{ind}}}\right| =\frac{1}{\sqrt{\left(1-\omega^2LC+\frac{R}{R_{\mathrm{out}}}\right)^2+\left(\frac{\omega L}{R_{\mathrm{out}}}+\omega RC\right)^2}}. \tag*{(43)}

and the phase is given by:

ϕ(ω)=arctan⁡(ω(CRRout+L)CLRoutω2−R−Rout).(44)\phi(\omega)=\arctan\left(\frac{\omega(CRR_{\mathrm{out}}+L)}{CLR_{\mathrm{out}}\omega^2-R-R_{\mathrm{out}}}\right). \tag*{(44)}

To estimate CC and LL in this circuit we consider the inner and outer radii of the toroidal coil

ri=Rt−a=52.5 mm,ro=Rt+a=64.5 mm,(45)\begin{aligned} r_i&=R_t-a=52.5\ \mathrm{mm},\\ r_o&=R_t+a=64.5\ \mathrm{mm}, \tag*{(45)} \end{aligned}

using RtR_t and aa, as listed in Table I.

The nominal outer wire diameter dwd_w is given by

dw=2rw=450 μm,(46)d_w=2r_w=450\ \mu\mathrm{m}, \tag*{(46)}

its insulation is 50 μm50\ \mu\mathrm{m} thick, i.e., the diameter of the current-carrying wire is 400 μm400\ \mu\mathrm{m}. The angle between two wire centers seen from the center of the toroid amounts to

α=2arcsin⁡(rwri−rw).(47)\alpha=2\arcsin\left(\frac{r_w}{r_i-r_w}\right). \tag*{(47)}

The maximum number of windings of a fully wound quadrant coil is therefore given by

Nwfq=floor⁡(π2α)=182.(48)N_w^{\mathrm{fq}}=\operatorname{floor}\left(\frac{\pi}{2\alpha}\right)=182. \tag*{(48)}

In order to estimate the inductance of a quarter coil, we quote the textbook formula for a long, straight and densely wound coil

Lfq=μ0μr(Nwfq)2ℓS≈57.09 μH,(49)L^{\mathrm{fq}}=\mu_0\mu_r\frac{\left(N_w^{\mathrm{fq}}\right)^2}{\ell}S\approx57.09\ \mu\mathrm{H}, \tag*{(49)}

where NwfqN_{\mathrm{w}}^{\mathrm{fq}} is the number of windings of the quarter toroid, and ℓ=π2ri\ell=\frac{\pi}{2}r_i is the length of the coil along its inner radius. SS denotes the cross section of the coil. Here the permeability of vacuum is

μ0=1.25663706127(20)⋅10−6 V s A−1 m−1(50)\mu_0=1.25663706127(20)\cdot10^{-6}\ \mathrm{V\,s\,A^{-1}\,m^{-1}} \tag*{(50)}

and the relative permeability μr\mu_r of the material of the coil body is close to unity.

As shown in Figure 5, the coils do not cover the quadrants completely, and instead of NwN_{\mathrm{w}}, given in Eq. (48), the real

number of windings used in a quarter coil amounted to

Nw=132.(51)N_{\mathrm{w}}=132. \tag*{(51)}

The corresponding real inductance of a partially wound coil with the above given number of windings corresponds to

L=NwNwfq⋅Lfq≈41.40 μH.(52)L=\frac{N_{\mathrm{w}}}{N_{\mathrm{w}}^{\mathrm{fq}}}\cdot L^{\mathrm{fq}}\approx41.40\,\mu\mathrm{H}. \tag*{(52)}

The capacitances of the twisted connecting wires are estimated like in a parallel plate capacitor using a length and a plate separation of

ℓC=5 cmanddC=0.1⋅dw,(53)\ell_C = 5\ \mathrm{cm} \quad\mathrm{and} \quad d_C = 0.1 \cdot d_w, \tag*{(53)}

yielding

Ctw=ϵ0⋅ℓC⋅dwdC≈4.4 pF,(54)C_{tw} = \epsilon_0 \cdot\frac{\ell_C \cdot d_w}{d_C} \approx4.4\ \mathrm{pF}, \tag*{(54)}

where the vacuum permittivity is

ϵ0≈8.854×10−12 A s V−1 m−1.(55)\epsilon_0 \approx8.854 \times10^{-12}\ \mathrm{A\,s\,V^{-1}\,m^{-1}}. \tag*{(55)}

These twisted wires are soldered to a 17 cm long coaxial cable with an specific capacity of 96 pF/m, resulting in a capacity of Ccc=16.3 pFC_{cc} = 16.3\ \mathrm{pF}. This ammounts to a total capcity

C=Ctw+Ccc=20.7 pF.(56)C = C_{tw} + C_{cc} = 20.7\ \mathrm{pF}. \tag*{(56)}

An estimate of the resonance frequency of a quarter of a Rogowski coil using the specified geometrical and physical parameters given above, yields

f0=12πLC≈5.44 MHz.(57)f_0 = \frac{1}{2\pi\sqrt{LC}} \approx5.44\ \mathrm{MHz}. \tag*{(57)}

The resistance of a coil quarter amounts to

R=Nw⋅8(a+dw)σCu⋅dw2≈0.61 Ω,(58)R = \frac{N_w \cdot8(a+d_w)}{\sigma_{\mathrm{Cu}}\cdot d_w^2} \approx0.61\ \Omega, \tag*{(58)}

where for the conductivity of copper after winding, a value of

σCu=55×106 S m−1(59)\sigma_{\mathrm{Cu}} = 55 \times10^6\ \mathrm{S\,m^{-1}} \tag*{(59)}

was used.

The function F(ω)F(\omega) from Eq. (43) is plotted in Figure 18 using the values for CC, LL, RR, and RoutR_{\mathrm{out}} listed in Table I. For an input impedance of Rout=500 kΩR_{\mathrm{out}} = 500\ \mathrm{k\Omega}, a quality factor for the operation of a quarter coil near the resonance ω0\omega_0 of

Figure 18. Plot of the frequency response function F(ω)F(\omega) from Eq. (43) using RoutR_{\mathrm{out}}, RR, CC, and LL given in Table I. The resonance frequency f0f_0 is given in Eq. (57), and the estimated quality factor Q≈175Q \approx175.

Q=ω0fwhm≈175(60)Q = \frac{\omega_0}{\mathrm{fwhm}} \approx175 \tag*{(60)}

can be estimated.

Effect of mirror currents

The distribution of the image current density for a pencil beam depends on its position (r,ψ)(r,\psi)1.

j(ρ,ϕ)=−I2πρ1−α21−2αcos⁡(ϕ−ψ)+α2δ(ρ−u)=−I2πρ[1+2∑m=1∞αmcos⁡(m(ϕ−ψ))]δ(ρ−u),(61)\begin{aligned} j(\rho,\phi) &= -\frac{I}{2\pi\rho}\frac{1-\alpha^2}{1-2\alpha\cos(\phi-\psi)+\alpha^2}\delta(\rho-u) \\ &= -\frac{I}{2\pi\rho}\left[1+2\sum_{m=1}^{\infty}\alpha^m\cos\left(m(\phi-\psi)\right)\right]\delta(\rho-u), \tag*{(61)} \end{aligned}

with α=rρ\alpha= \frac{r}{\rho},

where the delta-function has been introduced to state that the current density is confined to the inner tube surface because of the skin effect. The inner radius of the beam tube is denoted by uu, and the beam coordinates rr and ψ\psi are defined in Eq. (24). On integrating one finds that the total current on the wall matches exactly the beam current II.

A pick-up coil like a segmented Rogowski coil does not only capture the magnetic field of the beam, but also that of the wall currents, which constructively adds to the primary contribution by the beam, because they flow on the other side of the coils in reverse direction. The total flux through a coil due to the wall currents can be found similar to the discussion of Eq. (18). Equation (5) is a special case of the more general expression of the vector potential for a two-dimensional current distribution

Az(ρ,ϕ)=μ02π∫R2j(r⃗ ′)ln⁡(∣r⃗(ρ,ϕ)−r⃗ ′∣)dr⃗ ′,(62)A_z(\rho,\phi) = \frac{\mu_0}{2\pi}\int_{\mathbb{R}^2}j(\vec{r}^{\,\prime})\ln\left(\left|\vec{r}(\rho,\phi)-\vec{r}^{\,\prime}\right|\right)d\vec{r}^{\,\prime}, \tag*{(62)}

which for the wall currents takes the form

Az(ρ,ϕ)=μ0I4π2∫02π∫0∞1ρ′(1−α′2)δ(ρ′−s)1−2α′2cos⁡(ϕ′−ψ)+α′2ln⁡(ρ′2−2ρ′ρcos⁡(ϕ′−ϕ)+ρ2)ρ′ dρ′ dϕ′(63)A_z(\rho,\phi)=\frac{\mu_0 I}{4\pi^2}\int_0^{2\pi}\int_0^\infty\frac{1}{\rho'}\frac{(1-\alpha'^2)\delta(\rho'-s)}{1-2\alpha'^2\cos(\phi'-\psi)+\alpha'^2}\ln\left(\sqrt{\rho'^2-2\rho'\rho\cos(\phi'-\phi)+\rho^2}\right)\rho'\,d\rho'\,d\phi' \tag*{(63)}

with α′=rρ′\alpha'=\frac{r}{\rho'}.

In order to find the lowest order term (m=1m=1) in the displacement we can expand both the fraction and the logarithm (see Eq. (25))

Az(ρ,ϕ)=μ0I8π2∫02π(1+2rρcos⁡(ϕ′−ψ))(ln⁡(u)−ρucos⁡(ϕ′−ϕ))dϕ′(64)A_z(\rho,\phi)=\frac{\mu_0 I}{8\pi^2}\int_0^{2\pi}\left(1+2\frac{r}{\rho}\cos(\phi'-\psi)\right)\left(\ln(u)-\frac{\rho}{u}\cos(\phi'-\phi)\right)d\phi' \tag*{(64)}

and see that only the product of the two cos-terms yields the desired contribution.

Az(ρ,ϕ)=−μ0I4π2rρu2∫02πcos⁡(ϕ′−ψ)cos⁡(ϕ′−ϕ)dϕ′=−μ0I4πrρu2cos⁡(ϕ−ψ).(65)\begin{aligned} A_z(\rho,\phi)=-\frac{\mu_0 I}{4\pi^2}\frac{r\rho}{u^2}\int_0^{2\pi}\cos(\phi'-\psi)\cos(\phi'-\phi)d\phi' \\ &=-\frac{\mu_0 I}{4\pi}\frac{r\rho}{u^2}\cos(\phi-\psi). \tag*{(65)} \end{aligned}

Analogous to Eq. (22) the flux induced in the quadrant coil MM is obtained by the integration over its surface

ΦM=2aNwπ∫M(π/2)−θ(M+1)(π/2)+θ∫02πAz(ρ(β),β)cos⁡(β) dβ dϕ=aμ0NwI2π2ru2∫02π[Rt+acos⁡(β)]cos⁡(β) dβ⋅∫M(π/2)+θ(M+1)(π/2)−θcos⁡(ϕ−ψ)dϕ(66)\begin{aligned} \Phi_M=\frac{2aN_{\mathrm{w}}}{\pi}\int_{M(\pi/2)-\theta}^{(M+1)(\pi/2)+\theta}\int_0^{2\pi}A_z(\rho(\beta),\beta)\cos(\beta)\,d\beta\,d\phi\\ &=\frac{a\mu_0N_{\mathrm{w}}I}{2\pi^2}\frac{r}{u^2}\int_0^{2\pi}[R_t+a\cos(\beta)]\cos(\beta)\,d\beta \cdot\int_{M(\pi/2)+\theta}^{(M+1)(\pi/2)-\theta}\cos(\phi-\psi)d\phi \tag*{(66)} \end{aligned}
ΦM(x,y)=aμ0NwI2π2ru2aπ[c1,Mcos⁡(ψ)+d1,Msin⁡(ψ)]=μ0NwI2πa2u2[c1,Mx+d1,My](67)\begin{aligned} \Phi_M(x,y)=\frac{a\mu_0N_{\mathrm{w}}I}{2\pi^2}\frac{r}{u^2}a\pi[c_{1,M}\cos(\psi)+d_{1,M}\sin(\psi)] \\ &=\frac{\mu_0N_{\mathrm{w}}I}{2\pi}\frac{a^2}{u^2}[c_{1,M}x+d_{1,M}y] \tag*{(67)} \end{aligned}

with the coefficients c1,Mc_{1,M} and d1,Md_{1,M} defined in Eq. (27). In particular

Φ0(x,y)=μ0NwI2πa2u2(cos⁡θ−sin⁡θ)(x+y)=μ0NwIa(aRt2πu2)E1,0(x,y).(68)\begin{aligned} \Phi_0(x,y)=\frac{\mu_0N_{\mathrm{w}}I}{2\pi}\frac{a^2}{u^2}(\cos\theta-\sin\theta)(x+y) \\ &=\mu_0N_{\mathrm{w}}Ia\left(\frac{aR_t}{2\pi u^2}\right)E_{1,0}(x,y). \tag*{(68)} \end{aligned}

This flux adds to the primary one from the beam current, see Eq. A18. There the term in brackets has its beam current counterpart in

D1(b)=2bπ(11−b2−1)≈bπ(69)D_1(b)=\frac{2}{b\pi}\left(\frac{1}{\sqrt{1-b^2}}-1\right)\approx\frac{b}{\pi} \tag*{(69)}

which is about half the value in brackets for a Rogowski quarter coil close to the beam tube u≈Rtu\approx R_t. This explains in part the about 50% higher value of the linear term of the induced voltage with respect to the displacement found experimentally, see the discussion following Eq.17.

References

  1. [1]M. Pospelov and A. Ritz, Annals of Physics 318, 119 (2005), special issue.
  2. [2]B. Robson, Journal of High Energy Physics, Gravitation and Cosmology 04, 166 (2018).
  3. [3]W. Bernreuther, “CP violation and baryogenesis,” in CP Violation in Particle, Nuclear and Astrophysics, edited by M. Beyer (Springer Berlin Heidelberg, Berlin, Heidelberg, 2002) pp. 237–293.
  4. [4]F. Abusaif, I. Keshelashvili, K. Grigoryev, D. Mchedlishvili, L. Jorot, J. Pretz, U.-G. Meißner, A. Kulikov, A. Stahl, O. Felden, S. Martin, R. Stassen, P. Wüstner, A. Aksen- tev, O. Javakhishvili, E. Valetov, H. Soltner, B. Alberdi- Esuain, R. Talman, V. Shmakova, A. Kacharava, D. Hölscher, G. Ciullo, F. Müller, A. Silenko, R. Gebel, B. Lorentz, G. Na- tour, D. Grzonka, M. Zurek, J. Hetzel, P. Zupranski, S. Sid- dique, A. Magiera, I. Ciepal, C. Böhme, N. Nikolaev, S. Dymov, A. Lehrach, M. Gaisser, A. Wrońska, D. Heberling, M. Con- talbrigo, V. Kamerdzhiev, E. Stephenson, N. Nass, C. Weide- mann, Y. Senichev, M. Schott, J. Ritman, A. Wirzba, M. Beyß, M. Haj Tahar, M. Ströher, I. Koop, C. Carli, A. Lamont, M. Berz, J. Böker, A. Pesce, G. Tagliente, C. Käseberg, A. Saleev, T. Wag- ner, K. Makino, A. Aggarwal, J. Slim, D. Prashun, G. Macha- rashvili, J. Borburgh, N. Lomdize, V. Ponсza, D. Shergelashvili, M. Gagoshidze, M. Tabidze, S. Karanth, K. Laihem, T. Hah- nraths, P. Lenisa, V. Hejny, N. Giese, T. Sefzik, L. Barion, J. Michaud, A. Nogga, H. Straatmann, Y. Uzikov, S. Basile, F. Rathmann, A. Atanasov, Z. Metreveli, M. Rosenthal, Y. Val- dau, M. Simon, and J.-M. De Conto, CERN Yellow Report , 257 (2021).
  5. [5]F. Rathmann, A. Saleev, and N. Nikolaev (JEDI, srEDM), J. Phys. Conf. Ser. 447, 012011 (2013).
  6. [6]W. M. Morse, Y. F. Orlov, and Y. K. Semertzidis, Phys. Rev. ST Accel. Beams 16, 114001 (2013).
  7. [7]F. Rathmann, N. N. Nikolaev, and J. Slim, Phys. Rev. Accel. Beams 23, 024601 (2020).
  8. [8]R. Maier, Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment 390, 1 (1997).
  9. [9]C. Weidemann et al., Phys. Rev. ST Accel. Beams 18, 020101 (2015).
  10. [10]T. Wagner, A. Nass, J. Pretz, F. Abusaif, A. Aggarwal, A. Andres, I. Bekman, N. Canale, I. Ciepal, G. Ciullo, F. Dahmen, S. Dymov, C. Ehrlich, R. Gebel, K. Grigoryev, D. Grzonka, V. Hejny, J. Hetzel, A. Kacharava, V. Kamerdzhiev, S. Karanth, I. Keshelashvili, A. Kononov, A. Kulikov, K. Laihem, A. Lehrach, P. Lenisa, N. Lomidze, A. Magiera, D. Mchedlishvili, F. Müller, N. Nikolaev, A. Pesce, V. Ponсza, F. Rathmann, M. Retzlaff, A. Saleev, M. Schmühl, D. Shergelashvili, V. Shmakova, J. Slim, A. Stahl, E. Stephenson, H. Ströher, M. Tabidze, G. Tagliente, R. Talman, Y. Uzikov, Y. Valdau, and A. Wrońska, Journal of Instrumentation 16, T02001 (2021).
  11. [11]M. Wendt, IEEE Instrumentation & Measurement Magazine 24, 21 (2021).
  12. [12]J. Slim, R. Gebel, D. Heberling, F. Hinder, D. Hölscher, A. Lehrach, B. Lorentz, S. Mey, A. Nass, F. Rathmann, L. Reif- ferscheidt, H. Soltner, H. Straatmann, F. Trinkel, and J. Wolters, Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment 828, 116 (2016).
  13. [13]F. Hinder, H.-J. Krause, H. Soltner, and F. Trinkel, in 4th International Beam Instrumentation Conference (2016).
  14. [14]F. Abusaif, Development of compact, highly sensitive beam po- sition monitors for storage rings, Ph.D. thesis, RWTH Aachen University (2021).
  15. [15]D. Berners, L. Reginato, AIP Conf. Proc. 281, 168 (1992).
  16. [16]S. Hacıömeroğlu, D. Kawall, Y.-H. Lee, A. Matlashov, Z. Omarov, and Y. K. Semertzidis, PoS ICHEP2018, 279 (2019).
  17. [17]W. Rogowski and W. Steinhaus, Archiv für Elektrotechnik 1, 141 (1912).
  18. [18]W. Nassisi and A. Luches, Review of Scientific Instruments 50, 900 (1979).
  19. [19]D. G. Pellinien, M. S. Di Capua, S. E. Sampayan, H. Gerbracht, and M. Wang, Review of Scientific Instruments 51, 1535 (1980), https://doi.org/10.1063/1.1136119.
  20. [20]R.-Y. Han, W.-D. Ding, J.-W. Wu, H.-B. Zhou, Y. Jing, Q.-J. Liu, Y.-C. Chao, and A.-C. Qiu, Review of Scientific Instruments 86, 035114 (2015), https://doi.org/10.1063/1.4916094.
  21. [21]H. Samimi, A. Mahari, M. A. Farahnakian, and H. Mohseni, IEEE Sensors Journal 15, 651 (2015).
  22. [22]S. Merzliakov, C. Böhme, and V. Kamerdzhiev, IKP Annual Report, Forschungszentrum Jülich (2016).
  23. [23]C. Böhme, I. Bekman, V. Kamerdzhiev, B. Lorentz, M. Simon, and C. Weidemann, in 6th International Beam Instrumentation Conference (2018).
  24. [24]F. Terman, Radio Engineer’s Handbook, McGraw-Hill handbooks (McGraw-Hill Book Company, Incorporated, 1943).
  25. [25]J. D. Jackson, Classical Electrodynamics (Wiley, 1975).
  26. [26]I. S. Gradshteyn, I. M. Ryzhik, D. Zwillinger, and V. Moll, Table of integrals, series, and products; 8th ed. (Academic Press, Amsterdam, 2014).

Paper details

vlnc:W_3ve6fry5
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents