WorksPhysics and Astronomy
Meter-scale supersonic gas jets for multi-GeV laser-plasma accelerators
Abstract
Pushing the high energy frontier of laser wakefield electron acceleration (LWFA) to 10 GeV and beyond requires extending the propagation of relativistic intensity pulses to ~1 m in a low density () plasma waveguide. We present the development and characterization of two types of supersonic gas jet for meter-scale multi-GeV laser wakefield accelerators. The first type is a 30-cm long single-module gas jet, which demonstrates good axial uniformity using hydrogen, the preferred working gas for LWFA. The second type is a modular jet composed of multiple 11-cm-long modules. Longitudinal density profile control is demonstrated with a 2-module (22 cm long) hydrogen jet using gas valve trigger timing. A 1.0-m-long jet is then assembled from 9 modules, and generation of 1.0-m long hydrogen plasma is demonstrated using a femtosecond Bessel beam. To our knowledge, this is the longest gas jet laser plasma yet generated.
Introduction
Laser wakefield acceleration (LWFA) is a promising technique for compact electron accelerators due to the high accelerating gradient supported by plasma [1, 2], typically greater than in conventional rf-driven linear accelerators. Numerous applications of LWFA have been demonstrated, including high energy photon sources [3, 4], secondary particle generation [5, 6] and free-electron lasers [7]. For high energy colliders, staging of multiple LWFAs is proposed [8]. Recent advances in laser technology and computer simulations have enabled the generation of multi-GeV electron beams [9, 10, 11, 12, 13, 14], but it remains a challenge to demonstrate a combination of high charge (nC) and low energy spread (sub-percent). Precise control of the laser driver and plasma target are essential to achieve these goals.
In order to reach GeV energy gain in a single LWFA stage without dephasing of the acceleration process [2], a laser pulse must maintain its normalized vector potential by optical guiding in a low-density meter-scale plasma waveguide with on-axis density [10]. Development of multi-GeV LWFAs imposes demanding requirements on a plasma target: it should be easily accessible by experimental diagnostics, free standing to avoid laser and plasma damage of nearby materials, amenable to high repetition rate operation, and programmable in density profile. Well-known plasma targets in which waveguides are generated, namely gas cells [15, 16, 17] and capillary discharges [11, 18, 19], cannot meet all of these requirements. All requirements, however, can be met by an appropriately designed gas jet.
In this paper, we present the development of two types of meter-scale, low density, supersonic gas jet. The first type is a 30-cm-long single-module jet applied in recent research to deliver accelerated electron beams up to 10 GeV [10, 20] using hydrogen as the working gas. The second type is a modular jet, with which we demonstrate hydrogen plasma waveguides up to 1.0 m long. A modular jet enables axial density tailoring to mitigate dephasing between the accelerated electron beam and the optically guided laser pulse [16, 21, 22, 23]. It also enables control of electron injection along the laser propagation path, especially ionization injection [24, 25] using specially selected gas species.
30-cm single-module supersonic gas jet
Supersonic gas jets are widely used in laser plasma interactions [26, 27, 28, 29, 30, 31, 32, 33] with a typical range of gas density from to . Most supersonic gas jets provide a gas plume up to a couple of centimeters long and are backed by a single gas valve. For multi-GeV LWFAs, the laser propagation distance in plasma must be at least tens of centimeters. Such plasma is generated in a gas sheet tens of centimeters long [10, 20], for which it is difficult for a single inlet and valve to maintain the needed density along with a fast risetime. The latter is especially needed so that the working density is established quickly without deleterious gas loading of the experimental vacuum chamber.
Our single-module 30 cm-long gas jet design consists of an elongated supersonic slit nozzle fed by a reservoir backed by multiple solenoid valves. A prior 20 cm long version was used in LWFA experiments achieving electron bunches up to 5 GeV [10, 14, 20]. A drawing of the jet is shown in Figure 1. The reservoir, which serves to smooth the effect of discrete valves on axial variation of nozzle flow, is fed by 9 side-mounted miniature solenoid valves (Parker C21), each in a specialized coupler. The jet is composed of two blocks, with the valves mounted on the front block most visible in the figure. After valve actuation, gas flows through the front block via the inlet and channel, as depicted in Figure 1(b), and into the reservoir. The axially extended nozzle is formed by precise alignment of the two blocks. The de Laval nozzle cross sectional contour is designed using the design code CONTUR [34] and a Fortran90 realization [35]. The code is initialized with an inviscid contour with continuous curvature, which is then corrected for boundary layer growth to achieve uniform flow at the nozzle exit. The design is based on flow Mach number and throat width 200 μm.
Figure 1. (a) 30-cm-long single-module supersonic slit nozzle, fed by 9 solenoid valves, each supplied by separate or manifold-linked gas supply lines. (b) Longitudinal section of internal volume of jet, showing valve-actuated gas flow to reservoir, whose role is to axially smooth the gas flow. This section also serves as the elemental volume for our fluid flow simulations. The axially-extended supersonic nozzle, with a throat width of 200 m, is designed for Mach 5 flow.
The highly eccentric jet of Figure 1 does not easily lend itself to the usual interferometric measurement methods applied to rotationally asymmetric jets. One such method is tomography, achieved through multiple interferometric measurements by rotating the jet through a sequence of angles [27, 36, 37]. For a meter-scale jet, aside from the challenge of rotating it in a typically space-constricted vacuum chamber, the need for a very large field of view would require axially concatenated measurements, making tomography a difficult task. As an alternative, we use a longitudinal interferometric probe beam that propagates along the 30-cm-long nozzle to pick up a longitudinally integrated phase shift profile from the gas sheet. The longitudinal distribution of phase shift contributions is proportional to the longitudinal gas density profile. The latter is measured from plasma fluorescence induced by optical field ionization (OFI) driven by a Bessel beam above the jet nozzle orifice [10, 20]. Comparing the fluorescence from the gas jet against Bessel beam-induced OFI of static backfills of known pressure yields the axial gas density profile along the Bessel focus [10, 20], from which the transverse profile can be extracted for each longitudinal position.
The measurement results are shown in Figure 2. The gas jet was situated in a vacuum chamber with access windows for optical probing and imaging. The interferometric probe beam was a nm CW diode laser, expanded and collimated to 1 cm diameter. The probe beam propagated parallel to the orifice along the length of the gas sheet, accumulating a phase shift over 30 cm. The probe beam emerging at the end of the jet was imaged through a wavefront shearing interferometer onto a CMOS camera. The solenoid valves were connected by individual solid-state relays to 48VDC power supply; the relays and the camera were triggered by a digital delay generator. The camera image was gated by a 100 μs electronic shutter, much shorter than the ~1 ms evolution timescale of the gas flow. The full gas flow evolution was obtained by collecting a sequence of delayed interferograms by stepwise increase of the camera trigger delay with respect to the valve solenoid triggers. At each delay, 5-10 interferograms were taken (with the jet being fired 5-10 times) and their extracted phase profiles [38] were averaged to reduce the effect of camera noise and increase the signal-to-noise ratio.
Figure 2. Transverse and longitudinal density profile measurements of the 30-cm supersonic gas jet. (a) Longitudinal average transverse density profile at 6.9 bar backing pressure. (b) Temporal evolution of density mm above the nozzle orifice at 6.9 bar backing pressure. (c) Longitudinal average density versus backing pressure at mm (blue) and 8 mm (red) above the nozzle orifice. Fluid simulation result (“sim”) at mm is shown for comparison. (d) Axially resolved gas density profile at mm above the nozzle orifice. Fluorescence from approximately one-half the jet length was imaged to construct these profiles. The other half is approximately symmetric owing to the equidistant valve spacing and the reservoir and nozzle symmetry. The result of a fluid flow simulation (see text) is shown for comparison.
As the vacuum chamber pump out times were excessively long for hydrogen, for the interferometric measurements we elected to use nitrogen, with ~5 × faster pump out. Using nitrogen as a stand-in for hydrogen is justified by our fluid flow simulations [39], which show a small difference in reservoir and nozzle flow characteristics for the same inlet pressure. The major difference is in the boundary layer growth, which results in only slightly different Mach number and flow displacement from the nozzle walls for the same inlet pressure. Our simulations show that the maximum density difference between hydrogen and nitrogen gas jets is < ~15% for an inlet pressure 3.4 bar. Furthermore, the time evolution of the gas flow should be very similar for and : the rise time is the ratio of reservoir volume to volumetric flow rate out of the nozzle; the latter is similar for the same inlet pressure because the turbulent boundary layer in the 2 mm diameter gas flow channel (Figure 1(b)) for both and is comparatively negligible.
The integrated probe phase shift enables determination of the axially averaged transverse gas density profile. An example of an average density profile is shown in Figure 2(a), for a valve backing pressure of 6.9 bar . The gas density is sufficiently low that the probe phase fronts undergo negligible refractive curvature over 30 cm. The axially averaged transverse gas density profile is then calculated as , where is the integrated phase shift over cm, and are horizontal and vertical transverse positions with respect to the center of the jet orifice, is the probe wavevector, is the refractive index of nitrogen at STP, and is the density of at STP. Owing to the supersonic flow, the central gas density () is uniform up to mm above the nozzle orifice; the intent of the supersonic nozzle is to vertically extend the gas flow to enable Bessel beam-induced OFI at heights well above the orifice to avoid clipping of the Bessel beam by front face of the jet. For mm, the plot in Figure 2(b) shows the gas density rise time to be ms. The gas density plateaus for ms before dropping as the reservoir is depleted. In general, a fast rise time to the desired density is desirable for applications such as LWFA, where excessive gas buildup in the vacuum chamber can refract or distort a high intensity pulse before it reaches the gas jet. In Figure 2(c), the gas density at two heights above the nozzle orifice is shown to increase sub-linearly with backing pressure. We attribute this to partial opening of the valves at nearly maximum backing pressure.
The longitudinal gas density profile was measured by imaging the plasma fluorescence. Here, hydrogen was used as the working gas because the fluorescence image is bright enough for a single-shot image. OFI is induced by a 50 fs zeroth order Bessel beam whose central axis was placed in a range 3 to 12 mm above the orifice. The fluorescence intensity from hydrogen recombination is imaged by an sCMOS camera outside the vacuum chamber [10, 20] with a H- line filter (=656.3 nm). Images were for one-half of the jet length owing to limitation of the field of view by the chamber viewport aperture. The other half is approximately symmetric owing to the equidistant valve spacing and the reservoir and nozzle symmetry. The longitudinally-resolved H density profiles at 8 mm above the nozzle orifice are plotted in Figure 2(d) for various backing pressures. These profiles are consistent with the longitudinally averaged densities from interferometry plotted in Figure 2(c). The axial variation in density in each of the curves is from slight nozzle throat width variations from machining and block assembly.
To assist the jet and nozzle design and to gain insight into the flow, we conducted steady state 3D fluid simulations using Ansys Fluent with the SST k- model [39]. The flow domain consists of the 19-mm long internal volume shown in Figure 1(b) and a 19 mm 55mm 100 mm (LWH) rectangular block above the orifice as the vacuum chamber. The boundary condition at the two ends is continuity of all flow quantities (all gradients equal zero at the ends). The pressure at the inlet (shown in Figure 1(b)) used for the simulation is determined by matching the inlet flow rate with the Parker C21 flow curve for the experimental valve backing pressure. The black curve in Figure 2(d) is the simulated density at . The periodic curve is a concatenation of identical simulation results (each period is comprised of joined mirror image simulations of Figure 1(b)), where the density maximum is directly above the gas flow channel and the minima are farthest from the channel. The simulated longitudinal average gas density as a function of valve backing pressure is plotted in Figure 2(c), with up to ~20% deviation from the measurement. The longitudinal density profile is overlaid in black in Figure 2(d) for the case of 2.8 bar inlet pressure.
Modular supersonic gas jet
For gas jets longer than a few tens of centimeters, assembling them from modules is highly desirable. First, maintaining fabrication tolerances for long single-module jets is challenging. Second, well-characterized standard modules fabricated to high tolerance can be assembled to construct gas jets of any length. And third, modular jets can enable axial control of gas density and composition. For example, in LWFA a density upramp (an increase in plasma density in the guided beam direction) helps to phase match the accelerated electron bunch with the plasma wake [23]. In electron beam-driven wakefield accelerators, a precise density upramp improves beam focusing while maintaining beam emittance [40, 41, 42, 43]. Custom shaped gas jets are also used for enhancing betatron generation [3], long wavelength infrared generation [44, 45] and “photon acceleration” [46]. Recent work shows that localized dopant gas for ionization injection in LWFA will improve injected charge and reduce energy spread [47].
To achieve these goals, we developed the first modular design of a meter-scale supersonic slit nozzle and tested its operation. See Figure 3(a), which is a drawing of two linked modules. Each 11-cm-long module is mainly comprised of two opposing blocks that join together to form the reservoir and nozzle, as in the single module jet of Figure 1. The internal volume is similar to the de Laval nozzle profile of Figure 1(b). Each module is divided into 3 independent nozzle sections which can be separated by a custom-designed dividers aimed at various applications, with each nozzle section fed by its own solenoid valve. Each module also has ports for auxiliary valves for dopant gas injection (not shown). The valves share the same gas supply from a common manifold (comprised of parts additional to the nozzle blocks) that comes together upon multi-module assembly. Each added module, which extends the nozzle and manifold, is connected end-on and gasket-sealed to extend the jet to arbitrary lengths.

Figure 3. (a) 3D model of a two-module supersonic gas jet, including nozzles, manifolds and valves (behind the manifolds). (b) A 1-meter modular supersonic gas jet in use in vacuum. One of the 27 sections is filled with nitrogen and hydrogen elsewhere. An incoming laser pulse is focused by a diffractive logarithmic axicon to form a 1-meter focus above the gas jet. The plasma fluorescence is captured with an H- line filter where the nitrogen section is shown as a gap.
We have explored control of the axial density profile by adjusting either valve timing (transient control) or valve flow rates (steady state control). In the former case, all valves share the same power supply, while the valve trigger is delayed to adjust the flow rate on a sub-millisecond timescale. In the latter case, individual valve flow rates are controlled by voltage peak or pulse width modulation. The two methods can be combined to achieve more flexible control or reduce the gas load. In this paper we demonstrate the first method.
We characterized the axial H density profile of a two-module gas jet (Figure 4(a)) and the density rise to steady state for a single nozzle section (Figure 4(b)), using the fluorescence method [10, 20] used in Figure 2. No dividers were used between the nozzle sections within each module. Plots of ramped longitudinal density profiles, controlled by valve trigger timing, at various distances above the nozzle orifice are shown in Figure 4(a), where the variations about the local mean are from axial variations in the nozzle throat width. The sharp dip at mm is due to the obstruction of a 125-m thick shim placed between the two 11-cm-long modules to delineate the joint location. The required trigger timings in Figure 4(a) are informed by the measured density evolution with respect to the valve trigger of a single nozzle section, as plotted in Figure 4(b). Earlier than ms, there is negligible fluorescence signal, and the signal reaches steady state at ms. The transition to steady state takes ms with a nearly linear temporal ramp. For these conditions, control of axial density profiles is thus possible using temporally staggered valve triggers with inter-trigger intervals as short as s. The development of a valve control algorithm is in progress.
Figure 4. (a) Longitudinal H density profile of a two-module gas jet after steady state is reached. The valve backing pressure is 5.5 bar and each valve is driven by a 48VDC, 4-ms square wave pulse. (b) Temporal evolution of a single nozzle section taken at mm above the nozzle orifice. The valve operating conditions are the same as Figure 4(a).
Finally, as a proof of engineering feasibility, we assembled a 1.0-meter-long prototype gas jet from 9 modules of the type illustrated in Figure 3(a) and successfully tested it at the ALEPH laser facility [48] at Colorado State University. Figure 3(b) shows the H gas jet in operation in the vacuum chamber. A 100 mJ, 50 fs Bessel beam [49] formed a 1-meter-long OFI hydrogen plasma, 15 mm over the jet orifice. An auxiliary injector valve at one nozzle section was backed by nitrogen, with all other valves backed by hydrogen. The plasma fluorescence image was taken through H- line filter so that the nitrogen section appears as a gap.
Conclusions
We have demonstrated two types of meter-scale supersonic gas jets aimed at LWFA applications. The 30-cm-long single-module version has a reasonably uniform axial density distribution up to mm above the nozzle orifice, making it very suitable for use in high intensity laser facilities. To scale our design for generation of even longer jets while maintaining fabrication tolerances, and enabling control of axial density profiles, we have developed a modular supersonic jet design. Using two linked modules (6 nozzle sections) of total length 22 cm, we have demonstrated valve timing control of axial density ramps. And using 9 linked modules (27 nozzle sections) of total length 1.0 m, we have demonstrated generation of 1-m-long fully ionized hydrogen plasmas. To our knowledge, this is the longest gas jet plasma yet generated. The modular gas jet is a promising tool for laser wakefield generation and electron-beam driven wakefield acceleration.
ACKNOWLEDGMENTS
The authors thank Mayank Gupta, Nishchal Tripathi, Frederica Liu for lab assistance and Dr. Sebastian Lorenz, Dr. Gabriele Grittani for technical discussions. This work was supported by the U.S. DOE (DE-SC0015516, LaserNetUS DE-SC0019076/ FWP#SCW1668, and DE-SC0011375), and the Defense Advanced Research Projects Agency (DARPA) under the Muons for Science and Security Program.
AUTHOR DECLARATIONS
Conflict of Interest
The authors have no conflicts to disclose.
Author Contributions
All authors contributed equally to all aspects of this paper.
DATA AVAILABILITY
The data that support the findings of this study are available within the article and also from the corresponding author upon reasonable request.
References
- [1]T. Tajima and J. M. Dawson, "Laser Electron Accelerator," Phys Rev Lett 43, 267 (1979).DOI
- [2]E. Esarey, C. B. Schroeder, and W. P. Leemans, "Physics of laser-driven plasma-based electron accelerators," Rev Mod Phys 81, 1229 (2009).DOI
- [3]S. Corde, K. Ta Phuoc, G. Lambert, R. Fitour, V. Malka, A. Rousse, A. Beck, and E. Lefebvre, "Femtosecond x rays from laser-plasma accelerators," Rev Mod Phys 85, 1 (2013).DOI
- [4]F. Albert and A. G. R. Thomas, "Applications of laser wakefield accelerator-based light sources," Plasma Phys Control Fusion 58, 103001 (2016).DOI
- [5]L. Calvin, P. Tomassini, D. Doria, D. Martello, R. M. Deas, and G. Sarri, "Laser-driven muon production for material inspection and imaging," Front Phys 11, (2023).DOI
- [6]W. Schumaker, T. Liang, R. Clarke, J. M. Cole, G. Grittani, S. Kuschel, S. P. D. Mangles, Z. Najmudin, K. Poder, G. Sarri, D. Symes, A. G. R. Thomas, M. Vargas, M. Zepf, and K. Krushelnick, "Making pions with laser light," New J Phys 20, (2018).DOI
- [7]W. Wang, K. Feng, L. Ke, C. Yu, Y. Xu, R. Qi, Y. Chen, Z. Qin, Z. Zhang, M. Fang, J. Liu, K. Jiang, H. Wang, C. Wang, X. Yang, F. Wu, Y. Leng, J. Liu, R. Li, and Z. Xu, "Free-electron lasing at 27 nanometers based on a laser wakefield accelerator," Nature 595, 516 (2021).DOI
- [8]S. Steinke, J. Van Tilborg, C. Benedetti, C. G. R. Geddes, C. B. Schroeder, J. Daniels, K. K. Swanson, A. J. Gonsalves, K. Nakamura, N. H. Matlis, B. H. Shaw, E. Esarey, and W. P. Leemans, "Multistage coupling of independent laser-plasma accelerators," Nature 530, 190 (2016).DOI
- [9]J. L. Vay, C. G. R. Geddes, E. Esarey, C. B. Schroeder, W. P. Leemans, E. Cormier-Michel, and D. P. Grote, "Modeling of 10 GeV-1 TeV laser-plasma accelerators using Lorentz boosted simulations," Phys Plasmas 18, 123103 (2011).
- [10]B. Miao, J. E. Shrock, L. Feder, R. C. Hollinger, J. Morrison, R. Nedbailo, A. Picksley, H. Song, S. Wang, J. J. Rocca, and H. M. Milchberg, "Multi-GeV Electron Bunches from an All-Optical Laser Wakefield Accelerator," Phys. Rev. X 12, 31038 (2022).arxiv.org/abs/2112.03489
- [11]A. J. Gonsalves, K. Nakamura, J. Daniels, C. Benedetti, C. Pieronek, T. C. H. de Raadt, S. Steinke, J. H. Bin, S. S. Bulanov, J. van Tilburg, C. G. R. Geddes, C. B. Schroeder, Cs. Tóth, E. Esarey, K. Swanson, L. Fan-Chiang, G. Bagdasarov, N. Bobrova, V. Gasilov, G. Korn, P. Sasorov, and W. P. Leemans, "Petawatt Laser Guiding and Electron Beam Acceleration to 8 GeV in a Laser-Heated Capillary Discharge Waveguide," Phys Rev Lett 122, 084801 (2019).
- [12]A. Picksley, J. Stackhouse, C. Benedetti, K. Nakamura, H. E. Tsai, R. Li, B. Miao, J. E. Shrock, E. Rockafellow, H. M. Milchberg, C. B. Schroeder, J. van Tilburg, E. Esarey, C. G. R. Geddes, and A. J. Gonsalves, "Matched Guiding and Controlled Injection in Dark-Current-Free, 10-GeV-Class, Channel-Guided Laser Plasma Accelerators," arXiv preprint arXiv: 2408.00740 (2024).arxiv.org/abs/2408.00740
- [13]C. Aniculaesei, T. Ha, S. Yoffe, L. Labun, S. Milton, E. McCary, M. M. Spinks, H. J. Quevedo, O. Z. Labun, R. Sain, A. Hannasch, R. Zgadzaj, I. Pagano, J. A. Franco-Altamirano, M. L. Ringuette, E. Gaul, S. V Luedtke, G. Tiwari, B. Ersfeld, E. Brunetti, H. Ruhl, T. Ditmire, S. Bruce, M. E. Donovan, M. C. Downer, D. A. Jaroszynski, and B. M. Hegelich, "The acceleration of a high-charge electron bunch to 10 GeV in a 10-cm nanoparticle-assisted wakefield accelerator," Matter and Radiation at Extremes 9, 14001 (2023).DOI
- [14]J. E. Shrock, E. Rockafellow, B. Miao, M. Le, R. C. Hollinger, S. Wang, A. J. Gonsalves, A. Picksley, J. J. Rocca, and H. M. Milchberg, "Guided Mode Evolution and Ionization Injection in Meter-Scale Multi-GeV Laser Wakefield Accelerators," Phys Rev Lett 133, 045002 (2024).DOI
- [15]T. L. Audet, P. Lee, G. Maynard, S. D. Dufrénoy, A. Maitrallain, M. Bougeard, P. Monot, and B. Cros, "Gas cell density characterization for laser wakefield acceleration," Nucl Instrum Methods Phys Res A 909, 383 (2018).DOI
- [16]J. Kim, V. L. J. Phung, K. Roh, M. Kim, K. Kang, and H. Suk, "Development of a density-tapered capillary gas cell for laser wakefield acceleration," Review of Scientific Instruments 92, 023511 (2021).DOI
- [17]J. Osterhoff, A. Popp, Z. Major, B. Marx, T. P. Rowlands-Rees, M. Fuchs, M. Geissler, R. Hörlein, B. Hidding, S. Becker, E. A. Peralta, U. Schramm, F. Grüner, D. Habs, F. Krausz, S. M. Hooker, and S. Karsch, "Generation of stable, low-divergence electron beams by laser-wakefield acceleration in a steady-state-flow gas cell," Phys Rev Lett 101, 085002 (2008).pubmed.ncbi.nlm.nih.gov/18764625
- [18]A. Butler, D. J. Spence, and S. M. Hooker, "Guiding of High-Intensity Laser Pulses with a Hydrogen-Filled Capillary Discharge Waveguide," Phys Rev Lett 89, 185003 (2002).pubmed.ncbi.nlm.nih.gov/12398611
- [19]W. P. Leemans, A. J. Gonsalves, H.-S. Mao, K. Nakamura, C. Benedetti, C. B. Schroeder, Cs. Tóth, J. Daniels, D. E. Mittelberger, S. S. Bulanov, J.-L. Vay, C. G. R. Geddes, and E. Esarey, "Multi-GeV Electron Beams from Capillary-Discharge-Guided Subpetawatt Laser Pulses in the Self-Trapping Regime," Phys Rev Lett 113, 245002 (2014).pubmed.ncbi.nlm.nih.gov/25541775
- [20]J. E. Shrock, B. Miao, L. Feder, and H. M. Milchberg, "Meter-scale plasma waveguides for multi-GeV laser wakefield acceleration," Phys Plasmas 29, 073101 (2022).DOI
- [21]P. Sprangle, B. Hafizi, J. R. Peñano, R. F. Hubbard, A. Ting, C. I. Moore, D. F. Gordon, A. Zigler, D. Kaganovich, and T. M. Antonsen, "Wakefield generation and GeV acceleration in tapered plasma channels," Phys Rev E 63, 564051 (2001).
- [22]W. Rittershofer, C. B. Schroeder, E. Esarey, F. J. Grüner, and W. P. Leemans, "Tapered plasma channels to phase-lock accelerating and focusing forces in laser-plasma accelerators," Phys Plasmas 17, 063104 (2010).DOI
- [23]E. Guillaume, A. Döpp, C. Thaury, K. Ta Phuoc, A. Lifschitz, G. Grittani, J. P. Goddet, A. Tafzi, S. W. Chou, L. Veisz, and V. Malka, "Electron Rephasing in a Laser-Wakefield Accelerator," Phys Rev Lett 115, 155002 (2015).DOI
- [24]A. Pak, K. A. Marsh, S. F. Martins, W. Lu, W. B. Mori, and C. Joshi, "Injection and Trapping of Tunnel-Ionized Electrons into Laser-Produced Waves," Phys Rev Lett 104, 025003 (2010).pubmed.ncbi.nlm.nih.gov/20366604
- [25]C. McGuffey, A. G. R. Thomas, W. Schumaker, T. Matsuoka, V. Chvykov, F. J. Dollar, G. Kalintchenko, V. Yanovsky, A. Maksimchuk, K. Krushelnick, V. Yu. Bychenkov, I. V. Glazyrin, and A. V. Karpeev, "Ionization Induced Trapping in a Laser Wakefield Accelerator," Phys Rev Lett 104, 025004 (2010).
- [26]B. Landgraf, M. Schnell, A. Svert, M. C. Kaluza, and C. Spielmann, "High resolution 3D gas-jet characterization," Review of Scientific Instruments 82, 083106 (2011).DOI
- [27]A. Adelmann, B. Hermann, R. Ischebeck, M. C. Kaluza, U. Locans, N. Sauerwein, and R. Tarkeshian, "Real-time tomography of gas-jets with a wollaston interferometer," Applied Sciences (Switzerland) 8, 443 (2018).DOI
- [28]K. Schmid and L. Veisz, "Supersonic gas jets for laser-plasma experiments," Review of Scientific Instruments 83, 053304 (2012).DOI
- [29]S. Semushin and V. Malka, "High density gas jet nozzle design for laser target production," Review of Scientific Instruments 72, 2961 (2001).DOI
- [30]F. Sylla, M. Veltcheva, S. Kahaly, A. Flacco, and V. Malka, "Development and characterization of very dense submillimetric gas jets for laser-plasma interaction," Review of Scientific Instruments 83, 033507 (2012).DOI
- [31]J. L. Henares, P. Puyuelo-Valdes, F. Hannachi, T. Ceccotti, M. Ehret, F. Gobet, L. Lancia, J. R. Marquès, J. J. Santos, M. Versteegen, and M. Tarisien, "Development of gas jet targets for laser-plasma experiments at near-critical density," Review of Scientific Instruments 90, 063302 (2019).
- [32]T. Hosokai, K. Kinoshita, T. Watanabe, K. Yoshii, T. Ueda, A. Zhidkov, M. Uesaka, K. Nakajima, M. Kando, and H. Kotaki, "Supersonic gas jet target for generation of relativistic electrons with 12-TW 50-fs laser pulse," in 8th European Particle Accelerator Conference (2002), p. 981.
- [33]S. Lorenz, G. Grittani, E. Chacon-Golcher, C. M. Lazzarini, J. Limpouch, F. Nawaz, M. Nevrkla, L. Vilanova, and T. Levato, "Characterization of supersonic and subsonic gas targets for laser wakefield electron acceleration experiments," Matter and Radiation at Extremes 4, 015401 (2019).DOI
- [34]J. C. Sivells, A Computer Program for the Aerodynamic Design of Axisymmetric and Planar Nozzles for Supersonic and Hypersonic Wind Tunnels (1975).
- [35]A. Rona and F.-L. Zavalan, "Contur: A Computer Program for the Aerodynamic Design of Axisymmetric and Planar Supersonic and Hypersonic Nozzles," SSRN Electronic Journal (2022).DOI
- [36]U. Chaulagain, S. Karatodorov, M. Raclavský, S. Lorenz, M. Lamač, M. Albrecht, V. Tomkus, J. Dudutis, M. Mackevičiūtė, P. Gečys, and J. Nejdl, "Tomographic characterization of gas jets for laser-plasma acceleration with increased sensitivity," in International Conference on X-Ray Lasers 2020, D. Bleiner, ed. (SPIE, 2021), Vol. 11886, p. 118860A.DOI
- [37]S. Karatodorov, R. Lera, M. Raclavsky, S. Lorenz, U. Chaulagain, and J. Nejdl, "Multi-pass probing for high-sensitivity tomographic interferometry," Sci Rep 11, 15072 (2021).DOI
- [38]M. Takeda, H. Ina, and S. Kobayashi, "Fourier-transform method of fringe-pattern analysis for computer-based topography and interferometry," J Opt Soc Am 72, 156 (1982).DOI
- [39]"Ansys Fluent, Release 2023R2, AYSYS, Inc.," (2023).
- [40]C. Zhang, C. K. Huang, K. A. Marsh, X. L. Xu, F. Li, M. Hogan, V. Yakimenko, S. Corde, W. B. Mori, and C. Joshi, "Effect of fluctuations in the down ramp plasma source profile on the emittance and current profile of the self-injected beam in a plasma wakefield accelerator," Physical Review Accelerators and Beams 22, 111301 (2019).DOI
- [41]Y. Zhao, W. An, X. Xu, F. Li, L. Hildebrand, M. J. Hogan, V. Yakimenko, C. Joshi, and W. B. Mori, "Emittance preservation through density ramp matching sections in a plasma wakefield accelerator," Physical Review Accelerators and Beams 23, 011302 (2020).
- [42]M. D. Litos, R. Ariniello, C. E. Doss, K. Hunt-Stone, and J. R. Cary, "Beam emittance preservation using Gaussian density ramps in a beam-driven plasma wakefield accelerator," Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences 377, 0181 (2019).DOI
- [43]X. Li, A. Chancé, and P. A. P. Nghiêm, "Preserving emittance by matching out and matching in plasma wakefield acceleration stage," Physical Review Accelerators and Beams 22, 021304 (2019).DOI
- [44]Z. Nie, C. H. Pai, J. Hua, C. Zhang, Y. Wu, Y. Wan, F. Li, J. Zhang, Z. Cheng, Q. Su, S. Liu, Y. Ma, X. Ning, Y. He, W. Lu, H. H. Chu, J. Wang, W. B. Mori, and C. Joshi, "Relativistic single-cycle tunable infrared pulses generated from a tailored plasma density structure," Nat Photonics 12, 489 (2018).
- [45]Z. Nie, C. H. Pai, J. Zhang, X. Ning, J. Hua, Y. He, Y. Wu, Q. Su, S. Liu, Y. Ma, Z. Cheng, W. Lu, H. H. Chu, J. Wang, C. Zhang, W. B. Mori, and C. Joshi, "Photon deceleration in plasma wakes generates single-cycle relativistic tunable infrared pulses," Nat Commun 11, 2787 (2020).DOI
- [46]R. T. Sandberg and A. G. R. Thomas, "Photon Acceleration from Optical to XUV," Phys Rev Lett 130, 085001 (2023).DOI
- [47]J. D. Ludwig, S. C. Wilks, A. J. Kemp, G. J. Williams, E. Rockafellow, B. Miao, J. E. Shrock, H. M. Milhberg, J.-L. Vay, A. Huebl, R. Lehe, V. Tang, and B. Reagan, "A Laser-Based 100 GeV Electron Acceleration Scheme for Muon Production," To be published.
- [48]"Advanced Beam Laboratory," https://lasernetus.org/facilities/abl.
- [49]N. Tripathi, J. Shrock, B. Miao, E. Rockafellow, and H. Milchberg, "Plasma waveguide generation with diffractive logarithmic axicon," Bulletin of the American Physical Society (2023).
