betaFeedback

WorksPhysics and Astronomy

An Optimized Self-Adaptive Thermal Radiation Turn-Down Coating with Vanadium Dioxide Nanowire Array

Abstract

High performance metasurfaces for thermal radiative cooling applications can be identified using computational optimization methods. This work has identified an easy-to-fabricate temperature phase transition VO2 nanowire array laid atop dielectric BaF2 Fabry-Perot cavity-on-metal with total coating thickness of 2 um. This optimized structure has ability to self-adaptively switch between high reflectance at low temperature to high emissivity at high temperature in the broad thermal infrared spectrum. This design demonstrates exceptional turn-down figure-of-merit compared to previously realized configurations utilizing VO2 metasurfaces and multilayers. The mechanism is achieved with a sub-wavelength nanowire array effective medium that switches between anti-reflecting gradient coating and Fabry-Perot interference. This thin metasurface coating could impact self-cooling of the solar cells, batteries, and electrical devices where risk presents at high temperatures.

Nomenclature

SymbolDefinition
bbspace between nanowires, µm
ddthickness, µm
DCMDaytime Cooling Merit
E\mathbf{E}electric field vector
ffphase transition filling ratio
FOMTurn-Down Figure of Merit
hhnanowire height, µm,
ℏ\hbarreduced Planck’s constant [J·s]
IIradiative intensity or solar irradiance, W/sr·m²/µm
kBk_{\mathrm{B}}Boltzmann constant, J/K
nnrefractive index
NNnumber of samples
PPradiative power, W/m²
PDDpower dissipation density, W/m³
rrandomization array
TTtemperature, K
wwwidth of the nanowire, µm
WWwidth of the temperature range of metal-insulator transition, K
Greek symbols
ε\varepsilonemissivity
ϕ\phifilling ratio
φ\varphiazimuthal angle, deg
θ\thetaincident angle, deg
κ\kappaextinction coefficient
Λ\Lambdaperiod, µm
λ\lambdawavelength, µm
ω\omegaangular frequency, rad/s
ρ\rhoreflectivity
τ\tautransmissivity
Subscripts
0vacuum / center value
AM1.5air mass coefficient 1.5
BBblack body
coatcoating
concombined convection and conduction heat transfer
coolcooling
Ddielectric
EMTeffective medium theory
hhalfway through meta-insulator transition
iinsulator
mmetal
TEtransverse electric
TMtransverse magnetic

Table 3.

Introduction

Optical properties of thin films can be manipulated by introducing multilayered nano-patterns or periodic nanoelements that interface with electromagnetic waves from the visible to infrared. Various flavors of engineered nanoscale coatings include sub-diffraction plasmonic gratings [1, 2, 3], ultra-high reflection high contrast gratings [4, 5, 6], traditional diffraction gratings [7], and simple multilayers such as Fabry-Perot quarter-wave layers [8, 9, 10]. Among the considered, these nanoscale metasurfaces are potentially useful in photovoltaic device improvement and thermal emission regulation [11, 12, 13, 14]. Yet the key attribute to be sought after is thermochromic tuning – the ability to change optical properties with engineered surface temperature – which may result in self-cooling amid temperature or environmental changes. Temperature phase change materials, such as vanadium dioxide (VO2\mathrm{VO}_2) [9, 15, 16], SmNiO3_3 [17, 18], Ti3_3O5_5 [19], and many others can tailor the optical properties when things get heated.

VO2\mathrm{VO}_2 integrated in photonic multilayers and gratings have demonstrated thermal radiative switching [9, 15, 20] A common coating design utilizes the concept of Fabry-Perot cavity interference to obtain low emittance when cool and high emittance at hot [9]. More complex multilayers can be added, for the purpose of daytime radiative cooling, as absorption to solar radiation is minimized compared to the emission in the infrared [15]. Other designs have patterned at-wavelength size scale cylindrical gratings [21, 22]. So far, the turn-down thermal performance of such coatings has been less than anticipated. The optimal thermochromic metastructure needs to be designed by weighting the Planck blackbody distribution at the corresponding wavelengths and temperatures close to the phase transition, as determined by Wien’s displacement law. This work also considers the optimized structure that is easily feasible for nano/micro-fabrication, for a future in large scale-produced flexible radiative cooling blankets.

This work proposes a high turn-down grating by computational optimization of VO2\mathrm{VO}_2 nanowires in a thin film. VO2\mathrm{VO}_2 has a phase transition temperature at 340 K [14, 23, 24], where the phonon-electron structure transforms from insulating to metallic at temperatures above this transition temperature [25]. By randomized trials of at-and sub-wavelength deposited VO2\mathrm{VO}_2 nano/micro-features, a periodic VO2\mathrm{VO}_2 nanowire array and a solid VO2\mathrm{VO}_2 monolayer that sandwiches a quarter-wave thick lossless dielectric. Fabricated VO2\mathrm{VO}_2 nanowires typically of 50-150 nm in diameter were recently used demonstrating the breakdown on the Franz-Wiedemann law in thermoelectricity. [25]. These VO2\mathrm{VO}_2 nanowires were fabricated through vapor transport method, a bottom-up method [25, 26, 27, 28], and these VO2\mathrm{VO}_2 nanobeams can be laid and aligned in-plane, compared to the top-down photolithography and etching processes for traditional at-wavelength gratings [24]. This bottom-up method can greatly reduce complexity in fabrication, where minimal coating thickness is needed.

We utilize a Monte-Carlo optimization method to obtain the best nanowire array period and width of square cross-section VO2\mathrm{VO}_2 nanowires [29]. This method is applied to obtain the VO2\mathrm{VO}_2 monolayer as well, which serves as a gradual index anti-reflection layer above the fully-reflecting silver substrate. The broadband reflectance or broadband emissivity turn-down performance is quantified with a turn-down performance figure-of-merit (FOM), and compared with other VO2\mathrm{VO}_2 phase transition passive thermal radiation self-cooling coatings. The proposed structure has a total thickness of about 2.5 μm2.5\,\mu\mathrm{m}, including the 500 nm silver substrate. In this design, the coating on a flexible polymer backing sheet can be applied to alleviate the loss in efficiency for solar cells, whose temperatures can be as high as 80∘C80^\circ\mathrm{C} in summers under highly irradiative climates, such as Texas. The flexible coating can be applied to one or both sides of a vacuum gap between a solar cell housing and the roof. Similarly, it can be utilized for cooling compact processor components that gets as warm as 8080 to 100∘C100^\circ\mathrm{C}. Other usages include thermal management for lithium-ion cells casings, passive-switched spacecraft insulation blankets, and other common Earth-temperature thermal regulation applications.

Computational Methods

Theory of Optical Coatings

In this paper, Rigorous Coupled-Wave Analysis (RCWA), a well-established multilayered diffraction method to solve Maxwell equations [30, 31], is utilized to calculate the optical radiative properties of the optimized periodic coatings. The materials and geometrical parameters of the proposed coating is shown in Figure 1: The grating has a period of Λ\Lambda, nanowire width of ww, nanowire height of hh, distance between nanowires bb, thickness of the lossless dielectric is dDd_D, and thickness of the VO2\mathrm{VO}_2 sub-monolayer is dVO2d_{\mathrm{VO}_2}. Initially, the nanowire aspect ratio can be non-square to demonstrate possible effects.

Illustration and schematic of VO₂ nanowire array and VO₂ sub-monolayer coating on a silver substrate, with geometric parameters

Figure 1. (a) Illustration and schematic of Vanadium Dioxide (VO₂) nanowire / Dielectric material / VO₂ sub-monolayer coating on Silver (Ag) substrate. (b) Nomenclature of geometric parameters of the coating: Dielectric cavity or monolayer thicknesses dd, nanowire grating period Λ\Lambda, its width ww, height hh, and groove spacing bb.

In designing toward desirable high reflection or high emission properties, selection of optical parameters is important in tailoring its optical parameters. The contrast of the dielectric layers helps construct an anti-reflecting coating, where each transparent layer satisfies the geometric mean of the surround layers, such that n1=n0n2n_1=\sqrt{n_0 n_2} [32]. The underlying totally reflecting metal substrate can vary among aluminum, silver, gold, and others that are opaque and reasonably produced at sub-micron thickness. The anti-reflecting layer thicknesses must also satisfy quarter-wave law, such that h=λ/4nh=\lambda/4n. This quarter-wave method is widely used to determine broadband reflectance at certain wavelength range known as Bragg reflector, where high- and low-refractive index materials are stacked into multilayers with quarter-wave thickness [33]. On the other hand, Fabry-Perot resonance are formed by constructive interference of electromagnetic waves within the dielectric spacer sandwiched by metallic thin films. Ideally, these metallic boundaries are infinitesimally-thin and lossless. This produces perfect absorptivity or emissivity, and perfect transmissivity at moded frequencies [8, 9]. The switching between one to the other mechanism is how our turn-down capability is designed. In addition, for periodic features at the sub-wavelength, such that Λ≪λ\Lambda\ll\lambda, effective medium theory (EMT) can be applied to approximate the optical properties of gratings as expressed by a single layer composed of a filling ratio of dielectric functions [31, 34].

Radiative Properties

The dielectric function of VO2\mathrm{VO}_2 are obtained from empirical spectroscopy of its thin films [35]. Its optical properties are expressed with effective medium and Fermi-Dirac like distribution as shown,

εeff0.3=(1−f)εi0.3+fεm0.3(1)\varepsilon_{\mathrm{eff}}^{0.3}=(1-f)\varepsilon_{\mathrm{i}}^{0.3}+f\varepsilon_{\mathrm{m}}^{0.3} \tag*{(1)}
f(T)=11+exp⁡[WkB(1T−1Th)](2)f(T)=\frac{1}{1+\exp\left[\frac{W}{k_{\mathrm{B}}}\left(\frac{1}{T}-\frac{1}{T_{\mathrm{h}}}\right)\right]} \tag*{(2)}

where εi\varepsilon_{\mathrm{i}} and εm\varepsilon_{\mathrm{m}} is the dielectric function for insulator and metal VO2\mathrm{VO}_2 respectively. W=3.37W=3.37 K is width of the temperature range of metal-insulator transition. The partial monoclinic-to-rutile lattice phase transition occurs at Th=78.5∘CT_{\mathrm{h}}=78.5^\circ\mathrm{C}, where at this temperature, 50% of VO2\mathrm{VO}_2 is metallic [35]. Thus, the onset transition temperature of VO2\mathrm{VO}_2 from insulator to metal is 68°C. In Figure 2 (a), the imaginary part of the refractive index in VO2\mathrm{VO}_2 for the cold state is close to zero in the mid- to farinfrared (around 4 to 10 μm\mu\mathrm{m}). This infrared transparent region is highlighted in gray, and can play an important role in low absorption. On the other hand, it is absorbing in visible and far-infrared region.

Refractive index of vanadium dioxide and comparison of dielectric materials

Figure 2. (a) Refractive index of vanadium dioxide (VO2_{2}) at T=30 ∘CT = 30\,^{\circ}\mathrm{C} and T=80 ∘CT = 80\,^{\circ}\mathrm{C} obtained from Ref. [35]. The highlighted region shows near-zero extinction coefficient of the refractive index (κ\kappa) at the cold state. (b) Comparison of refractive index of dielectric materials, including barium fluoride (BaF2_{2}), magnesium fluoride (MgF2_{2}), silicon (Si), and zinc sulfide (ZnS).

As shown in Figure 2(b), there are a few broadly infrared-transparent dielectric candidate materials that can be utilized as the dielectric spacer. These include barium fluoride (BaF2_2), zinc sulfide (ZnS), and silicon (Si). The most common, silicon, has broadly constant refractive index of around n=3.4n = 3.4, with no extinction coefficient provided undoped low number density and optical quality [31]. For BaF2_2 and ZnS, the refractive index is lower, but have absorption component in far infrared region, due to the Reststrahlen effect of gaps in the upper-level electron bands [36, 37]. The lower refractive index is appreciated in the arrangement of anti-reflection gradient index of layers. In certain other turn-down coating designs, MgF2_2 can also be the candidate for the dielectric materials. However, it has a significant absorption near the Reststrahlen band, which may result in reduction in the performance of radiative properties [38]. Insulators with absorption in infrared wavelengths up to 30 μm\mu\mathrm{m} must be avoided, as a wavelength window cutoff in the upper limit leaves more than 10% of Planck radiation at atmospheric temperatures unaccounted for. The balance of broad infrared transparency and close to unity refractive index needs to be considered.

Optimization of Parameters

The parameter optimization scheme is conducted by creating four arrays of random NN numbers, rir_i, for randomizing Λ\Lambda, bb, hh, and dVO2d_{\mathrm{VO}_2}. The arrays consisting of random numbers are then used to produce random value of size arrays for those four parameters as: Λ=Λ0±r1Λ0\Lambda= \Lambda_0 \pm r_1\Lambda_0, b=b0±r2b0b = b_0 \pm r_2b_0, h=h0±r3h0h = h_0 \pm r_3h_0, and dVO2=d0±r4d0d_{\mathrm{VO}_2} = d_0 \pm r_4d_0. Candidates with b>Λb > \Lambda are rejected. The NN combinations of candidates are created and evaluated with the following figure-of-merit (FOM),

FOM=R300R350=∫0.3 μm30 μmρλ,300EBB,300 dλ∫0.3 μm30 μmρλ,350EBB,350 dλ(3)\mathrm{FOM} = \frac{R300}{R350} = \frac{\int_{0.3\,\mu\mathrm{m}}^{30\,\mu\mathrm{m}} \rho_{\lambda,300} E_{\mathrm{BB},300}\,\mathrm{d}\lambda}{\int_{0.3\,\mu\mathrm{m}}^{30\,\mu\mathrm{m}} \rho_{\lambda,350} E_{\mathrm{BB},350}\,\mathrm{d}\lambda} \tag*{(3)}

where ρλ\rho_\lambda is the spectral reflectivity, and EBB,TE_{\mathrm{BB},T} is the spectral emissive power which expressed as EBB,T=πIBB,TE_{\mathrm{BB},T} = \pi I_{\mathrm{BB},T}, where IBB,T=(4π2c02ℏ/λ5)/[exp⁡(2πℏc0/λkBT)−1]I_{\mathrm{BB},T} = (4\pi^2 c_0^2 \hbar/ \lambda^5) / [\exp(2\pi\hbar c_0 / \lambda k_{\mathrm{B}}T) - 1] is the blackbody intensity at the corresponding temperature TT. The integrated wavelength ranges from 0.3 μm\mu\mathrm{m} and 30 μm\mu\mathrm{m}, which covers adequate sampling of the blackbody spectrum at atmospheric temperatures up to the Solar spectrum. The FOM is based on coating reflectivity to normalize from the opaque metal substrate, for sake of FOM comparison with other configurations on other metal substrates. The reflectivity is used to assess the coating’s ability to reject surrounding radiation at higher temperature. On the other hand, for other calculations, the spectral emissivity is calculated as ελ=1−ρλ\varepsilon_{\lambda}=1-\rho_{\lambda}, considering that Kirchhoff’s law of radiation is satisfied being the substrate is thick enough to be opaque. By fitting the parameter inputs into this summative FOM metric, further parametric stipulations can be applied to the next round of optimizations as explained in next section. Since the optimization consists of four parameters to randomize, N=104N=10^{4} candidates are sufficient to search for the optimal structure. Yet optimizing more parameters could require additional samples needed, but recent machine learning techniques such as Bayesian optimization may be implemented in the future for its adaptive learning of the best parameters with reasonable convergence [39].

Results and Discussion

Radiative Turn-Down Performance of Optimized Coating

In this work, BaF2\mathrm{BaF}_{2} is chosen as the dielectric spacer and dBaF2d_{\mathrm{BaF}_{2}} is quarter-wave thickness set constant as λ0/4nBaF2=1.385 μm\lambda_{0}/4n_{\mathrm{BaF}_{2}}=1.385\ \mu\mathrm{m}. The center wavelength λ0\lambda_{0} is chosen as 8.2 μm8.2\ \mu\mathrm{m}, corresponding to emissive power at 80°C (hot condition). The cold condition is selected to be 30°C, a typical warm day or summer night in Texas. BaF2\mathrm{BaF}_{2} has a low index of approximately nBaF2=1.5n_{\mathrm{BaF}_{2}}=1.5, which contrasts highly against VO2\mathrm{VO}_{2}. BaF2\mathrm{BaF}_{2} is preliminarily selected as the lossless dielectric due to its broad essentially zero imaginary component of the refractive index up to the Reststrahlen absorption peak near 50 μm50\ \mu\mathrm{m} [36]. The dielectric function of Ag is Drude-like with plasma constants from Ref. [1], and that of BaF2\mathrm{BaF}_{2} is obtained from Ref. [37].

First, the dVO2d_{\mathrm{VO}_{2}} sub-monolayer is found to have optimal thickness at 450 nm via our randomization trials. It is thinner than the anticipated quarter-wave thickness of λ0/4nVO2=840 nm\lambda_{0}/4n_{\mathrm{VO}_{2}}=840\ \mathrm{nm}, where nVO2=2.38n_{\mathrm{VO}_{2}}=2.38 at λ=8.2 μm\lambda=8.2\ \mu\mathrm{m}. The maximized FOM is quite broad over N=104N=10^{4} samples, with no random scattering of outliers. Deviations of a few tens of nanometers from this value remains high performance. On searching for an optimal filling ratio of VO2\mathrm{VO}_{2} nanowire-to-period (ϕ=w/Λ\phi=w/\Lambda), we narrowed it to the range between 0.4 to 0.6. Thus, a reasonable additional restriction can be applied to the optimization method where the width of the VO2\mathrm{VO}_{2} nanowire cross-section is equal to the nanowire height. Optimizations of rectangular nanowires did not result in additional maximization of FOM. Square cross-section VO2\mathrm{VO_2} nanowires with high length-to-width aspect ratios have been realized for nanoscale applications [23]. This round of optimizations is conducted with the aspect ratio restrictions, resulting in the best optimized structure with parameters: Λ=194\Lambda= 194 nm, b=114b = 114 nm, w=h=80w = h = 80 nm, dBaF2=1.385d_{\mathrm{BaF_2}} = 1.385 μ\mum, and dVO2=0.450d_{\mathrm{VO_2}} = 0.450 μ\mum. This design corresponds to the highest FOM = 1.47, meaning that the emitted thermal radiation at high temperature exceeds that absorbed at low temperature.

The thermal radiation turn-down mechanism can be explained starting with Figure 2(a), where the large difference of extinction coefficient κ\kappa between 30°C and 80°C is observed in the highlighted gray region of the spectrum. This component is close to zero at the low temperature, but well above one and increasing in magnitude in the mid to far infrared region at the high temperature. Figure 3(a) shows the averaged spectral emissivity between TM- and TE-polarized waves calculated by RCWA. The emissivity is unavoidably high at any temperature in the visible wavelengths, as there is always a bandgap transition. Meanwhile in the infrared region, the region corresponding to the extinction coefficient flip overlaps with the atmospheric transparency window (inverse of clouds on a warm day near 290 K). With the optimized design, the emissivity switches between low emissivity and high emissivity as the temperature increases. Additionally, the hemispherical emissivity (εh\varepsilon^{\mathrm{h}}) across all polar incident angles and averaged electromagnetic wave polarizations shows small differences compared to the normal emissivity, except for the far-infrared region beyond 25 μ\mum. This is attributed to some minor absorption due to the off-quarter-wave thickness attenuation length from a slightly lossy BaF2\mathrm{BaF_2} as it approaches its Reststrahlen band, and will be dissected in our forthcoming discussion.

Averaged and normal emissivity spectra

Figure 3. (a) The averaged emissivity spectrum calculated with Rigorous Coupled-Wave Analysis (RCWA). The dashed lines show the hemispherical emissivity spectra. The background atmospheric transparency spectrum is shown in Ref. [45]. (b) Normal emissivity spectrum calculated with Effective Medium Theory (EMT) of optimized VO2_2 Nanowire / BaF2_2 / VO2_2 coating on Ag substrate for TM (solid line) and TE wave (dashed line).

The normal polar incident angle emissivity in transverse magnetic (TM) and transverse electric (TE) wave calculated in effective medium theory (EMT) are shown in Figure 3(b), and it shows drastic differences between them. This is due to differences in effective refractive index in extraordinary and ordinary components, as expressed by [34],

εTM=εVO2εair(1−ϕ)εVO2+ϕεair(4)\varepsilon_{\mathrm{TM}} = \frac{\varepsilon_{\mathrm{VO_2}}\varepsilon_{\mathrm{air}}}{(1-\phi)\varepsilon_{\mathrm{VO_2}}+\phi\varepsilon_{\mathrm{air}}} \tag*{(4)}
εTE=ϕεVO2+(1−ϕ)εair(5)\varepsilon_{\mathrm{TE}} = \phi\varepsilon_{\mathrm{VO_2}}+(1-\phi)\varepsilon_{\mathrm{air}} \tag*{(5)}

where ϕ\phi is the width-to-period filling ratio for gratings. The index of air is εair=1.0\varepsilon_{\mathrm{air}} = 1.0. The resulting effective refractive index for TM wave is calculated at around nTM∼1.3n_{\mathrm{TM}} \sim1.3, and has low κTM\kappa_{\mathrm{TM}} value for both 30°C and 80°C, which suppresses the emissivity. On the other hand, the contribution of VO2_2 is much higher in the effective refractive index for TE waves, which nTE∼1.7n_{\mathrm{TE}} \sim1.7 and ∼3.6\sim3.6 at 30°C and 80°C, respectively. The κTE\kappa_{\mathrm{TE}} value is much higher at 80°C, given by 2.0 to 4.0, and so higher emissivity is obtained. We note the near-perfect emissivity of 0.997 at 10.5 μ\mum, attributed to the optimized design of the Fabry-Perot mechanism.

The following figures further investigate the underlying mechanisms of the turn-down coating’s near-idealized performance. Figure 4 shows the emissivity calculated by RCWA as a function of both incident angle and wavelength. The results show the high turn-down performance of emissivity between cold and hot cases for both TM and TE waves. This is especially true in the neighborhood of 10 μ\mum, as the normal and broadly oblique emissivity switches from near-zero to near-unity. The emissivity in the TM wave is slightly suppressed to due to the extinction coefficient in the effective medium extraordinary polarization being close to zero for higher temperature. On the other hand, the contrast in TE wave polarization is higher due to the switch between insulating and metallic dispersion along the nanowire. In essence, the axial dispersion along the nanowire offers the highest contrast corresponding to the TE polarization, while maintaining good transmittance overall due to the sparsity of interactions of electric fields along the nanowire cross-section. Interestingly, the high emissivity observed at far-infrared region for TM wave is not present at TE wave. EMT was also able to capture the angular polarization dependency in TM wave, where the emissive power is produced only in xx-zz plane at normal polar incident angle.

Spectral and incident angle-dependent emissivity contours

Figure 4. Spectral and incident angle-dependent emissivity contours of TM wave at (a) cold and (b) hot states, and TE wave at (c) cold and (d) hot states, calculated by RCWA.

Figure 5 demonstrates the power dissipation density (PDD) plots between cold and hot states. PDD in W/m3^3 is given by,

Power dissipation density distribution in the optimized VO₂ nanowire design

Figure 5. Power dissipation density (PDD) distribution (TM wave only) of the optimized VO2\mathrm{VO}_2 NW / BaF2_2 / VO2\mathrm{VO}_2 design for (a) cold state (T=30∘CT = 30^\circ\mathrm{C}) and (b) hot state (T=80∘CT = 80^\circ\mathrm{C}) calculated by RCWA. The white dashed box shows the inset figures within the VO2\mathrm{VO}_2 nanowire array region. The pink lines delineate the interfaces in the structure.

PDD=12ε0Im⁡(ε)ω∣E∣2(6)\mathrm{PDD} = \frac{1}{2}\varepsilon_0 \operatorname{Im}(\varepsilon)\omega\lvert\mathbf{E} \rvert^2 \tag*{(6)}

where ω\omega is the angular frequency corresponding to the wavelength, and E\mathbf{E} is the local electric field as function of the xx-zz plane. In Figure 5 (a), the mechanism behind the high reflectance in the cold state is due to graded refractive index from top to bottom. With ϕ=0.4\phi= 0.4, the effective refractive index of the nanowires is nEMT=1.55n_{\mathrm{EMT}} = 1.55, close to the refractive index of the dielectric, nBaF2=1.44n_{\mathrm{BaF_2}} = 1.44 at 30°C and 8 μm\mu\mathrm{m} wavelength. As the nanowire width becomes infinitesimally small the FOM plateaus close to 1.5. This makes sense as the VO2\mathrm{VO}_2 layer seeks to obtain a refractive index close to unity. The spectra calculated with an 80 nm-thick effective nanowire medium resulted the same normal emissivity, with discernable differences of off-normal spectra due to the anisotropic effective medium distribution [34]. The refractive index of the sub-monolayer VO2\mathrm{VO}_2 is nVO2=2.38n_{\mathrm{VO}_2}=2.38, which is a gradual transition to higher index before the reflecting and opaque silver substrate. The power is concentrated in a sliver at the interface between the VO2\mathrm{VO}_2 sub-monolayer and silver. Using the penetration depth definition δ=λ/4πκ\delta=\lambda/4\pi\kappa, the attenuation depth in the silver substrate is 11 nm, almost negligible. Some absorption is seen in VO2\mathrm{VO}_2, and none through the BaF2\mathrm{BaF}_2 dielectric cavity layer, as the fields are transmitted in the cold state. Since the extinction coefficient of VO2\mathrm{VO}_2 is non-zero (κ=0.08\kappa=0.08 at 8 μm\mu\mathrm{m}) in the transparency region shown in Figure 2(a), the reflection is not perfect. This 5.7% VO2\mathrm{VO}_2 monolayer thickness to its penetration depth ratio is expressed correspondingly in the minimum emissivity at 8 μm\mu\mathrm{m} shown in Figure 3(a).

On the other hand, from Figure 5(b), the electromagnetic field power dissipation density (PDD) within the VO2\mathrm{VO}_2 nanowire and VO2\mathrm{VO}_2 bottom layer at the hot state temperature shows higher absorption compared to lower temperature due to its much higher κ\kappa value of 3.3. In the hot state, the 450 nm-thick VO2\mathrm{VO}_2 sub-monolayer becomes to the metallic substrate, such that the lossless dielectric insulator becomes a Fabry-Perot resonator. This plasmonic resonance is induced within the nanowire and within the BaF2\mathrm{BaF}_2 layer due to its metallic phase in vanadium dioxide layer, behaving like metal-insulator-metal (MIM) [40]. Localization of power absorption can be up to 1000 W/m3^3 in both VO2\mathrm{VO}_2 layers. The finesse in this optimized design is due to the upper metal layer being a loosely-packed thin metal film, such that enough radiation is able to enter the dielectric cavity and constructively interfere to induce maximum absorption. Hence, the adaptive design switches from anti-reflecting coating by refractive index gradient layering to a plasmonic resonant cavity that concentrates power absorption/emission within the VO2\mathrm{VO}_2 during the coating’s hot state.

Although many optical materials and coatings should perform well regardless of radiation incident angle, some angular dependence is observed at far infrared region at around 28 μm\mu\mathrm{m}. In Figure 6, we investigate the anomalous high absorption marked by the TM wave “lobes” in Figure 4(a) and (b). The absorptive effect is due to a thick BaF2\mathrm{BaF}_2 layer, where spectral emissivity increases with incident angle and reaches up to 1.0 at higher angles due to increasing value of κ\kappa value and propagation length. Neither the silver substrate nor the VO2_2 components have effects on the oblique angle emissivity. The incident far infrared light is trapped in the slightly lossy cavity and constructs multiple reflections between VO2_2 NW and VO2_2 sublayer. This phenomenon is only observed in TM waves at oblique incident angles, as the electric fields form surface plasmon modes at the lower corners of the dielectric VO2_2 nanowires [41] The emissivity is further enhanced at hot state (Figure 6 d-Figure 6f) because metallic phase in VO2_2 absorbs the light, especially the under-cavity monolayer. At steeper angles, emissive power is then concentrated within BaF2_2 cavity, as the mechanism transitions toward cavity extinction and trapping. In practice, this angle-dependent emissivity in cold state should be avoided to improve its overall performance with radiation coming from any polarization type. With this consideration of the Reststrahlen band extinction of this particular infrared material, other dielectric materials should be considered as replacement, as discussed in the next section.

Oblique TM wave power dissipation density distribution for the optimized VO2 NW/BaF2/VO2 design

Figure 6. Oblique TM wave power dissipation density (PDD) distribution of the optimized VO2\mathrm{VO}_{2} NW / BaF2_{2} / VO2\mathrm{VO}_{2} design at λ=28 μm\lambda= 28\,\mu\mathrm{m} for incident angles: (a) θ=0∘\theta= 0^\circ, (b) θ=30∘\theta= 30^\circ, and (c) θ=60∘\theta= 60^\circ at cold state, and (d) θ=0∘\theta= 0^\circ, (e) θ=30∘\theta= 30^\circ, and (f) θ=60∘\theta= 60^\circ at hot state calculated by RCWA.

Performance Enhancement by Dielectric Spacer Types

Figure 7 (a) shows a sweeping of a correspondingly quarter-wave thick layer of purely real component and wavelength-independent refractive indices from unity to Germanium (n=4.0n = 4.0). The VO2_2 parameters are unchanged from the previously-found optimized configuration. Here, a higher FOM performance was found by an idealized dielectric spacer of refractive index n=2.2n = 2.2. This FOM can be as high as 1.86, slightly higher compared to the optimized structure with BaF2_2 of 1.47. In this regard, we learn that other broadly infrared-transparent materials with higher index such as silicon (n=3.4n = 3.4) could achieve similar turn-down performance. Other low-index materials can have similar FOM as the BaF2_2 configuration, such as potassium chloride (n=1.49n = 1.49) and potassium bromide (n=1.55n = 1.55), as long as the Reststrahlen band is far beyond the thermal infrared regime (λ>40\lambda> 40 μm). Ideally, medium-index materials such as zinc selenide (n=2.4n = 2.4) or zinc sulfide (n=2.2n = 2.2) can deliver FOM > 1.47. It becomes pressing to seek crystalline and interfacial compatibility between these medium-index dielectrics with VO2_2. Difficulties may arise in more common dielectric oxides with medium-index, such as silicon dioxide or titanium dioxide, due to their Lorentz absorption in the mid- to far-infrared [42].

In the next investigation shown in Figure 7b, it was found the filling ratio of the VO2_2 NW array plays an important role in high reflectance in cold state due to index-matching between the VO2_2 NW / air effective medium (EMT) layer and the dielectric material. The previous investigation for BaF2_2 shows it reached a maximum at ϕ=0.4\phi= 0.4, but it is not true for the other dielectric materials. The highest FOM is achieved for both ZnS and the constant n=2.2n = 2.2 index at ϕ=0.3\phi= 0.3. The slightly lower FOM of ZnS compared to constant n=2.2n = 2.2 is due to its closer Reststrahlen band peak at 30.5 μ\mum [37]. For a high-index dielectric such as Si, the best filling ratio of the VO2_2 NW array is zero, which is unrealistic. This is due to the departure of index-gradient matching. For instance, the effective refractive index within the visible to near infrared region of EMT is nEMT=1.0∼2.0n_{\mathrm{EMT}} = 1.0\sim2.0 for filling ratio of ϕ=0.4\phi= 0.4, which matches overall with the refractive index of the BaF2_2 cavity, nBaF2=1.4∼1.5n_{\mathrm{BaF}_2} = 1.4\sim1.5. Other dielectric materials such as zinc sulfide (ZnS) and silicon (Si) may replace BaF2_2 with an appropriate filling ratio to improve overall reflectance, but with consideration of realizable nanowire sizing. Other dielectric spacers have been used in other studies of turn-down coatings, which we will make a comparison.

Comparison of Radiative Turn-Down Performance

Figure 8 (a) and (Figure 8b) compares the reflectance at cold state and the emissivity at the hot state of our optimized structure (VO2_2 nanowires / BaF2_2 / VO2_2) with a rudimentary quarter-wave (QW) layers as first-order approximation (BaF2_2 QW / VO2_2 QW), a Fabry-Perot resonator (thin VO2_2 / Si) [9], and a multi-component radiative cooler system (Multilayer band-pass filter / VO2_2 / MgF2_2) [15]. The QW layers are presented to demonstrate its comparable high coating transmissivity as a proof of an anti-reflecting film, similar to our optimized nanowire structure in the cold state. The Planck emissive power spectrum at 80°C is also posed to predict the total emissivity between the different configurations. Table I compares the summative radiative performances. The FOM of the optimized structure is 1.47, higher than other realized structures of 0.86 and 0.6, respectively. The basic quarter-wave layers that share the same material composition as our optimized structure has a higher FOM of 1.06. The absence of the semi-metallic upper nanowire array layer produces no cavity mode interference, but shares a peak local emissivity near 8 μ\mum. The key understanding is the absence of the upper solid VO2_2 layer for the purpose of creating a Fabry-Perot cavity in turn reduces performance, especially the needed high reflectance in

Comparison of normal reflectivity and normal emissivity spectra

Figure 8. Comparison of (a) normal reflectivity and (b) normal emissivity spectra of this optimized grating (VO2_2 Nanowires / BaF2_2 / VO2_2), simple quarter-wave layers (BaF2_2 QW / VO2_2 QW), a Fabry-Perot resonator (VO2_2 / Si), and a radiative cooler system (Band-pass filter / VO2_2 / MgF2_2). All are opaque coatings on metal substrates. The Planck blackbody emissive power function (EbE_b) at 80°C is plotted in shaded gray.

Thus, the VO2_2 nanowire array is a good compromise in gaining the high turn-down, while any Fabry-Perot multilayer configuration has lower turn-down performance due to narrower band emission. We noticed some consequential differences in performance in the multi-component Fabry-Perot cooler system from our recalculations is likely due to absorption by MgF2_2 near its Reststrahlen band near 20 μm20\ \mu\mathrm{m} [38], as well as differences from more modern spectroscopic surveys of VO2\mathrm{VO}_2 thin films [35, 43]. Additionally, Table 1 compares the quantities of radiative heat emitted to the surroundings. The emitted power at normal incidence is given by,

StructureFOMEemitE_{\mathrm{emit}}qnet′′q_{\mathrm{net}}^{\prime\prime}
30°C80°C30°C80°C
Optimized Grating (VO2_2 Nanowires / BaF2_2 / VO2_2)1.475356027396
Quarter-Wave Layers (BaF2_2 QW / VO2_2 QW)1.063144320330
Fabry-Perot Resonator (VO2_2 / Si)0.863435918265
Radiative Cooler System (Filter / VO2_2 / MgF2_2)0.606120217144

Table 1. Comparison of performances among similar turn-down coatings, showing the FOM defined in Eq. (3), the emitted radiation flux (W/m2^2) from the coating (EemitE_{\mathrm{emit}}), and the net radiative heat flux between the coating and atmosphere at 290 K (qnet′′q_{\mathrm{net}}^{\prime\prime}).

Eemit=∫0.3 μm30 μmελ,TEBB,T dλ(7)E_{\mathrm{emit}}=\int_{0.3\ \mu\mathrm{m}}^{30\ \mu\mathrm{m}}\varepsilon_{\lambda,T}E_{\mathrm{BB},T}\,\mathrm{d}\lambda \tag*{(7)}

where this quantity represents the potential to emit to a neighboring reradiating surface, such as a multilayer insulation blanket [44]. The error to these figures is no more than 10% due to the upper wavelength cutoff at room temperature and above. We also calculate the integrated hemispherical emissivity combined with absorption from atmospheric radiation, given by,

qnet′′=∫0.3 μm30 μmελ,ThEb,T dλ−∫0.3 μm30 μm(1−τatm,λ)ελ,ThEBB,Tamb dλ(8)q_{\mathrm{net}}^{\prime\prime}=\int_{0.3\ \mu\mathrm{m}}^{30\ \mu\mathrm{m}}\varepsilon_{\lambda,T}^{h}E_{\mathrm{b},T}\,\mathrm{d}\lambda-\int_{0.3\ \mu\mathrm{m}}^{30\ \mu\mathrm{m}}\left(1-\tau_{\mathrm{atm},\lambda}\right)\varepsilon_{\lambda,T}^{h}E_{\mathrm{BB},T_{\mathrm{amb}}}\,\mathrm{d}\lambda \tag*{(8)}

where τatm,λ\tau_{\mathrm{atm},\lambda} is the atmospheric transparency shown in Figure 2(b) [45]. The ambient temperature TambT_{\mathrm{amb}} is assumed to be 290 K. The purpose of presenting this combined net radiative flux is to assess the respective coatings’ performance exposed to diffuse cloudy or night sky. By analyzing Eq. (7), our optimized structure produces 560 W/m2560\ \mathrm{W}/\mathrm{m}^2 in the hot state, while just 53 W/m253\ \mathrm{W}/\mathrm{m}^2 in the cold state. This ratio of power turn-down is 10.6:1. An even higher turn-down ratio is seen with Eq. (8), for net hemispherical heat flux with atmosphere, where the ratio is 14.7:1. The magnitudes of the hot state emissive power is not insignificant compared to the irradiative power flux from the Sun (∼1400 W/m2\sim1400\ \mathrm{W}/\mathrm{m}^2). The net radiative performance of comparable structures also show good turn-down but at predicted lower hot state magnitudes.

Although the emissive power turn-down ratio for the simpler QW layers is higher (14.3:1), the maximum emitted power is lower, therefore the reduced FOM. This FOM accounts for both the turn-down ratio as well as the emissive power difference between hot and cold state. A higher magnitude emissive power at the hot state is therefore more important, especially for compact components with small radiating surface areas. The optimized VO2\mathrm{VO}_2 NW design can also provide dense thermal radiative energy directed toward the atmosphere, almost doubling the capability for radiative rejection compared to other designs. Furthermore, we learn that the basic quarter-wave structure in fact outperforms a Fabry-Perot solid VO2\mathrm{VO}_2 layer on dielectric. This means the concept of a Fabry-Perot structure may not be best suited, compared to a simpler dual anti-reflection layer. We note the performance is bolstered by absorption within the dielectric medium at off-normal incident angles. At these emissive power magnitudes at high temperature, these coatings may be capable of passive radiative cooling under the Sun via careful tuning of spectral response in the visible wavelength.

Evaluation of Daytime Radiative Cooling

This section assesses the possibility of the optimized coating as a daytime radiative cooler, and the metrics developed to quantify this capability. The Daytime Cooling Merit (DCM) is defined in Eq. (9),

DCM=Pcool,350Pcool,300=Pcoat,350−Patm,350−Psun,350+Pcon,350Pcoat,300−Patm,300−Psun,300+Pcon,300(9)\mathrm{DCM}=\frac{P_{\mathrm{cool},350}}{P_{\mathrm{cool},300}}=\frac{P_{\mathrm{coat},350}-P_{\mathrm{atm},350}-P_{\mathrm{sun},350}+P_{\mathrm{con},350}}{P_{\mathrm{coat},300}-P_{\mathrm{atm},300}-P_{\mathrm{sun},300}+P_{\mathrm{con},300}} \tag*{(9)}

as a ratio of energy balances from the diffuse coating (coat), atmosphere (atm), the Sun (sun), and combined conduction and convective cooling (con) to an ambient temperature in atmosphere Tamb=290 KT_{\mathrm{amb}} = 290\ \mathrm{K}. The coating radiative power flux in W/m2\mathrm{W}/\mathrm{m}^{2} is obtained by hemispherical integration of the spectral directional emissivity with blackbody temperature function of the coating. The incoming atmospheric power flux is calculated with the diffuse atmospheric transparency spectrum seen in Figure 3(a), and integrated with the spectral directional absorptivity at ambient temperature. We obtained the solar absorption spectrum from IAM1.5,λI_{\mathrm{AM1.5},\lambda} at normal incidence spectral absorptivity, as the coating can be mechanically dialed to be sun-pointing. Lastly, heat rejection due to both convection and conduction to ambient is appropriately grouped into an overall coefficient hch_{\mathrm{c}}, which is conservatively set as 10 W/m2⋅K10\ \mathrm{W}/\mathrm{m}^{2}\cdot\mathrm{K}. The combined power from this component is Pcon,T=hc(T−Tamb)P_{\mathrm{con},T}=h_{\mathrm{c}}(T-T_{\mathrm{amb}}). We note that the integration cutoff for solar irradiation at the lower wavelength of 0.3 μm0.3\ \mu\mathrm{m} gives 3%3\% error, compared to the 9%9\% error for the 30 μm30\ \mu\mathrm{m} upper limit in bodies at terrestrial temperatures.

Applying Eq. (9) onto the optimized structure results in DCM=Pcool,350/Pcool,300=271/(−615)=−0.44\mathrm{DCM}=P_{\mathrm{cool},350}/P_{\mathrm{cool},300}=271/(-615)=-0.44. This negative DCM indicates that the coating absorbs more sunlight rather than emit heat at the low temperature near ambient. However, at the high temperature which VO2\mathrm{VO}_{2} becomes metallic, the coating rejects more heat than it absorbs. Since its absorptivity in the visible to near infrared region is high for any temperature as shown in Figure 3, the coating’s outgoing emissive power, Pcoat,TP_{\mathrm{coat},T} must overcome the sunlight absorption power, Psun,TP_{\mathrm{sun},T}. In Figure 9, plotting the total radiative outgoing power with temperatures from ambient to 370 K370\ \mathrm{K}, an equilibrium temperature is reached at around T=345 KT=345\ \mathrm{K} (Pcool,T=0P_{\mathrm{cool},T}=0) which is just above the phase transition temperature of vanadium dioxide at 340 K. The radiative cooling power drastically increases after passing the VO2\mathrm{VO}_2 phase transition temperature, and it can attain powers up to 470 W/m2^2. This is similar to the net radiative cooling power at hot state in Table 1. The performance somewhat leans on the contribution of combined convection and conduction cooling power, in which a well-insulated environment around the coating may mean less cooling capability at the hot state. Therefore, the coating is able to reach self-equilibrium near the phase transition temperature of VO2\mathrm{VO}_2. In the insulating phase near ambient temperature, the coating warms up, but in the metallic phase at high temperatures, it passively cools.

Overall coating radiative cooling power and coating temperature

Figure 9. Overall coating radiative cooling power, PcoolP_{\mathrm{cool}} and the temperature of the coating (blue line). The red, light blue, orange, and green solid lines represent PcoatP_{\mathrm{coat}}, PatmP_{\mathrm{atm}}, PsunP_{\mathrm{sun}}, and PconP_{\mathrm{con}}, respectively. The shaded area represents the metallic phase of VO2\mathrm{VO}_{2}.

This cooling capability only in the hot state exceeds that of previously designed daytime radiative cooling coatings, such as SiO2_2 / HfO2_2 multilayer [46], SiO2_2-polymer hybrid metamaterial [47], and plain PDMS coatings [48]. Table 2 shows that daytime equilibrium temperature of the optimized grating is greater than ambient temperature, which does not compare with plain daytime radiative cooler materials and designs. Rather, the high cooling power just beyond the VO2\mathrm{VO}_2 transition temperature is noticeably significant compared to others. Therefore, we learn that the optimized VO2\mathrm{VO}_2 NW / BaF2_2 / VO2\mathrm{VO}_2 is useful as a radiative cooler only when in shade and not placed under the sun. However, it is commendable for this 2 μ\mum-thin coating to ensure that an equilibrium temperature can be obtained close to 345 K. This is not only helpful in maintaining efficiency in photovoltaic devices, but also it can be used for thermal management of components such as rechargeable batteries, fuel tanks, and engines on both terrestrial and space vehicles.

StructureTcoating−TambT_{\mathrm{coating}}-T_{\mathrm{amb}} (K)Cooling power (W/m2^2)DCM
Optimized Grating+46271 (350 K)-0.44
SiO2_2 / HfO2_2 Multilayer-4.9821.86
Glass-Polymer Hybrid Metamaterial----->110>110-----
PDMS (300 μ\mum)-61881.86

Table 2. Table 2. Comparison of temperature difference Tcoating−TambT_{\mathrm{coating}} - T_{\mathrm{amb}} (K), maximum cooling power (W/m2^2), and the Daytime Cooling Merit defined in Eq. (9), with other daytime radiative cooling coatings.

Conclusion

We have proposed a self-adaptive high turn-down VO2\mathrm{VO}_2 nanowire / BaF2_2 / VO2\mathrm{VO}_2 / silver thin film of around 2 μ\mum for passive thermal management applications. Our Monte-Carlo optimization method was utilized to obtain the optimal structure parameters for VO2\mathrm{VO}_2 components. It is compared with Fabry-Perot multilayers using VO2\mathrm{VO}_2, and a higher figure of merit (FOM) of 1.47 is obtained compared to other structures (FOM < 1). Ideally, the optimal refractive index of the dielectric spacer is n=2.2n = 2.2, which is slightly higher than BaF2_2 (n=1.55n = 1.55). The electric field is reflected at the interface between VO2\mathrm{VO}_2 bottom layer and silver for lower temperature for high reflectance, but a high value of power dissipation density (PDD) is observed within the VO2\mathrm{VO}_2 in higher temperature, leading to high emissivity in infrared region. The optimized structure provides cooling power of 271 W/m2^2 at 350 K whose power is higher compared to previously studies structures. Lastly, this work provides the idea of computational method for optimizing the photonic structures to obtain the desired optical properties. The obtained data may be utilized for machine learning (ML) technique to obtain predictive FOM with complex structural geometries and exotic materials, both dielectrics and phase transition. This structure can be extended to two-dimensional gratings to possibly further improve its figure-of-merit (FOM) as well as daytime radiative cooling merit (DCM) turn-down to an even higher value. This turn-down allows the device to self-reject the heat out of the devices such as solar cells, computer systems, engines, and functions as self-adaptive radiative cooling device.

Relationship of FOM and the refractive index of the quarter-wave thick spacer

(a)

Correlation of FOM and filling ratio of VO₂ nanowires with different dielectric materials

(b)

Figure 7. (a) Relationship of FOM and the refractive index of the quarter-wave thick spacer. (b) The correlation of FOM and filling ratio of VO2_2 nanowires with different dielectric materials including BaF2_2 (black), ZnS (red), Si (blue), and constant n=2.2n = 2.2 (green).

References

  1. [1]Zhao, B. and Z.M. Zhang, Study of magnetic polaritons in deep gratings for thermal emission control. Journal of Quantitative Spectroscopy and Radiative Transfer, 135 (2014) 81-89.DOI
  2. [2]Zhao, B., J.M. Zhao, and Z.M. Zhang, Resonance enhanced absorption in a graphene monolayer using deep metal gratings. Journal of the Optical Society of America B, 32 (2015).DOI
  3. [3]Araki, K. and R.Z. Zhang, Plasmon-resonance emission tailoring of "origami" graphene-covered photonic gratings. Opt Express, 28 (2020) 22791-22802.DOI
  4. [4]Chang-Hasnain, C.J. and W. Yang, High-contrast gratings for integrated optoelectronics. Advances in Optics and Photonics, 4 (2012).
  5. [5]Qiao, P., et al., Theory and design of two-dimensional high-contrast-grating phased arrays. Optics Express, 23 (2015) 24508-24524.DOI
  6. [6]Qiao, P., W. Yang, and C.J. Chang-Hasnain, Recent advances in high-contrast metastructures, metasurfaces, and photonic crystals. Advances in Optics and Photonics, 10 (2018).DOI
  7. [7]Harvey, J.E. and R.N. Pfisterer, Understanding diffraction grating behavior: including conical diffraction and Rayleigh anomalies from transmission gratings. Optical Engineering, 58 (2019).DOI
  8. [8]Wang, L.P., et al., Spatial and temporal coherence of thermal radiation in asymmetric Fabry-Perot resonance cavities. International Journal of Heat and Mass Transfer, 52 (2009) 3024-3031.DOI
  9. [9]Taylor, S., Y. Yang, and L. Wang, Vanadium dioxide based Fabry-Perot emitter for dynamic radiative cooling applications. Journal of Quantitative Spectroscopy and Radiative Transfer, 197 (2017) 76-83.
  10. [10]Keçebaş, M.A. and K. Şendur, Enhancing the spectral reflectance of refractory metals by multilayer optical thin-film coatings. Journal of the Optical Society of America B, 35 (2018).DOI
  11. [11]Uleman, F., et al., Resonant Metagratings for Spectral and Angular Control of Light for Colored Rooftop Photovoltaics. ACS Applied Energy Materials, 3 (2020) 3150-3156.DOI
  12. [12]Garnett, E.C., et al., Photonics for Photovoltaics: Advances and Opportunities. ACS Photonics, 8 (2021) 61-70.DOI
  13. [13]Li, W., Y. Li, and K.W. Shah, A materials perspective on radiative cooling structures for buildings. Solar Energy, 207 (2020) 247-269.DOI
  14. [14]Ulpiani, G., et al., On the energy modulation of daytime radiative coolers: A review on infrared emissivity dynamic switch against overcooling. Solar Energy, 209 (2020) 278-301.DOI
  15. [15]Ono, M., et al., Self-adaptive radiative cooling based on phase change materials. Opt Express, 26 (2018) A777-A787.DOI
  16. [16]Taylor, S., et al., Spectrally-selective vanadium dioxide based tunable metafilm emitter for dynamic radiative cooling. Solar Energy Materials and Solar Cells, 217 (2020) 110739.DOI
  17. [17]Torriss, B., J. Margot, and M. Chaker, Metal-Insulator Transition of strained SnNiO3 Thin Films: Structural, Electrical and Optical Properties. Sci Rep, 7 (2017) 40915.DOI
  18. [18]Yoo, P. and P. Liao, Metal-to-insulator transition in SmNiO3 induced by chemical doping: a first principles study. Molecular Systems Design & Engineering, 3 (2018) 264-274.DOI
  19. [19]Liu, R., J.-X. Shang, and F.-H. Wang, Electronic, magnetic and optical properties of β-Ti3O5 and λ-Ti3O5: A density functional study. Computational Materials Science, 81 (2014) 158-162.DOI
  20. [20]Kort-Kamp, W.J.M., et al., Passive Radiative “Thermostat” Enabled by Phase-Change Photonic Nanostructures. ACS Photonics, 5 (2018) 4554-4560.
  21. [21]Long, L., et al., Thermally-switchable spectrally-selective infrared metamaterial absorber/emitter by tuning magnetic polariton with a phase-change VO2 layer. Materials Today Energy, 13 (2019) 214-220.DOI
  22. [22]Long, L., S. Taylor, and L. Wang, Enhanced Infrared Emission by Thermally Switching the Excitation of Magnetic Polariton with Scalable Microstructured VO2 Metasurfaces. ACS Photonics, 7 (2020) 2219-2227.DOI
  23. [23]Liu, K., et al., Recent progresses on physics and applications of vanadium dioxide. Materials Today, 21 (2018) 875-896.DOI
  24. [24]Cui, Y., et al., Thermochromic VO2 for Energy-Efficient Smart Windows. Joule, 2 (2018) 1707-1746.DOI
  25. [25]Lee, S., et al., Anomalously low electronic thermal conductivity in metallic vanadium dioxide. Science, 355 (2017) 371-374.DOI
  26. [26]Cheng, Y., et al., Structure and Metal-to-Insulator Transition of VO2 Nanowires Grown on Sapphire Substrates. European Journal of Inorganic Chemistry, 2010 (2010) 4332-4338.DOI
  27. [27]Kim, M.W., et al., Substrate-mediated strain effect on the role of thermal heating and electric field on metal-insulator transition in vanadium dioxide nanobeams. Sci Rep, 5 (2015) 10861.DOI
  28. [28]Shi, R., et al., Low-temperature wafer-scale fabrication of vertical VO2 nanowire arrays. Applied Physics Letters, 117 (2020).DOI
  29. [29]Wild, W.J. and H. Buhay, Thin-film multilayer design optimization using a Monte Carlo approach. Optics Letters, 11 (1986) 745-747.pubmed.ncbi.nlm.nih.gov/19738747
  30. [30]Moharam, M.G., et al., Formulation for stable and efficient implementation of the rigorous coupled-wave analysis of binary gratings. Journal of the Optical Society of America A, 12 (1995) 1068-1076.DOI
  31. [31]Zhang, Z.M., Nano/microscale heat transfer. 2020.
  32. [32]Hecht, E., Optics. 2017: Pearson Education.
  33. [33]Inan, H., et al., Photonic crystals: emerging biosensors and their promise for point-of-care applications. Chem Soc Rev, 46 (2017) 366-388.DOI
  34. [34]Liu, X.L., R.Z. Zhang, and Z.M. Zhang, Near-field radiative heat transfer with doped-silicon nanostructured metamaterials. International Journal of Heat and Mass Transfer, 73 (2014) 389-398.DOI
  35. [35]Wan, C., et al., On the Optical Properties of Thin-Film Vanadium Dioxide from the Visible to the Far Infrared. Annalen der Physik, 531 (2019) 1900188.DOI
  36. [36]Andersson, S.K., M.E. Thomas, and C.E. Hoffman, Multipphonon contribution to the reststrahlen band of BaF2. Infrared Physics & Technology, 39 (1998) 47-54.DOI
  37. [37]Querry, M. Optical constants of minerals and other materials from the millimeter to the ultraviolet. 1987.
  38. [38]Giordano, J., Temperature dependence of IR spectra of zinc and magnesium fluoride. Journal of Physics C: Solid State Physics, 20 (1987) 1547-1562.DOI
  39. [39]Sakurai, A., et al., Ultranarrow-Band Wavelength-Selective Thermal Emission with Aperiodic Multilayered Metamaterials Designed by Bayesian Optimization. ACS Central Science, 5 (2019) 319-326.DOI
  40. [40]Ogawa, S. and M. K. Kimata, Metal-Insulator-Metal-Based Plasmonic Metamaterial Absorbers at Visible and Infrared Wavelengths: A Review. Materials (Basel), 11 (2018).DOI
  41. [41]Abdulhalim, I., Coupling configurations between extended surface electromagnetic waves and localized surface plasmons for ultrahigh field enhancement. Nanophotonics, 7 (2018) 1891-1916.DOI
  42. [42]Kischkat, J., et al., Mid-infrared optical properties of thin films of aluminum oxide, titanium dioxide, silicon dioxide, aluminum nitride, and silicon nitride. Applied Optics, 51 (2012) 6789-6798.DOI
  43. [43]Verleur, H.W., A.S. Barker, and C.N. Berglund, Optical Properties of VO₂ between 0.25 and 5 eV. Physical Review, 172 (1968) 788-798.
  44. [44]Donahedian, M. and D.G. Gilmore, Spacecraft thermal control handbook. 2003: Aerospace Press.
  45. [45]Lord, S.D., A new software tool for computing Earth's atmospheric transmission of near- and far-infrared radiation. Vol. 103957. 1992: Ames Research Center.
  46. [46]Raman, A.P., et al., Passive radiative cooling below ambient air temperature under direct sunlight. Nature, 515 (2014) 540-544.DOI
  47. [47]Zhai, Y., et al., Scalable-manufactured randomized glass-polymer hybrid metamaterial for daytime radiative cooling. Science, 355 (2017) 1062-1066.DOI
  48. [48]Mandal, J., et al., Hierarchically porous polymer coatings for highly efficient passive daytime radiative cooling. Science, 362 (2018) 315-319.DOI

Paper details

vlnc:W_45g8gwwb
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents