betaFeedback

WorksPhysics and Astronomy

A wide-range temperature-dependent deep potential for sodium with near-experimental accuracy from melting to the critical point

Abstract

We construct temperature-dependent deep potentials for sodium using finite-temperature DFT data obtained with the PBE, AM05, and r2r^2SCAN exchange-correlation functionals and investigate the thermophysical properties of sodium from room temperature to the critical region. The predicted critical parameters show a dependence on the exchange-correlation functional. The model based on the r2r^2SCAN functional gives a critical temperature Tc=2.508(8)T_c=2.508(8) kK, density ρc=0.203(4)ρ_c=0.203(4) g/cm3^{3}, and pressure Pc=0.249(6)P_c=0.249(6) kbar, in close agreement with the recommended values. This model is then used to reconstruct the normal-pressure and critical isobars and to calculate the enthalpy, heat capacities, thermal expansion coefficient, bulk moduli, Grüneisen parameter, and speed of sound. The calculated normal-pressure bcc density differs by only 0.06% from the experimental value. Direct solid-liquid coexistence simulations give a melting temperature of 346(2)346(2) K, 25 K below the recommended value, consistent with the sensitivity expected from meV/atom free-energy errors. Liquid-vapor coexistence simulations reproduce the binodal and yield a surface tension that approaches zero near the critical point. The calculated self-diffusion coefficient and shear viscosity extend the available transport-property data into the expanded-liquid and near-critical regions, where direct experimental information is sparse. We also demonstrate the thermodynamic consistency of the results by comparing the speed of sound obtained from direct acoustic simulations with that calculated from the equation of state.

Introduction

Liquid sodium has long been used as a coolant and heat-transfer medium, particularly in fast-reactor systems [1, 2]. Accurate thermophysical data over broad ranges of temperature and pressure are therefore required for the construction of equations of state and for predictive thermal-hydraulic modeling [3, 4]. Near atmospheric pressure, extensive experimental data and recommended correlations are available for the density, enthalpy, heat capacity, speed of sound, viscosity, and surface tension of liquid sodium [5, 6, 7, 8]. These recommendations draw on calorimetric measurements of the heat capacity and enthalpy [9], liquid-enthalpy measurements up to 1505 K [10], acoustic measurements at elevated pressures [11], and surface-tension measurements [12, 13]. At higher temperatures, however, particularly in the expanded-liquid and near-critical regimes, direct experimental constraints become increasingly sparse.

Finite-temperature density-functional theory (DFT) and quantum molecular dynamics (QMD) allow one to calculate the thermodynamic properties of liquid metals with electronic excitation taken into account [14, 16]. Alongside first-principles approaches, classical embedded-atom models have also been used to calculate liquid–vapor coexistence, critical parameters, self-diffusion, and viscosity of sodium [17].

In our previous papers, QMD calculations were applied to liquid metals near melting and in the critical region [18, ?, 20, 21, 22, 23]. However, direct QMD simulations are limited by the accessible system size and trajectory length, which complicates calculations of long-wavelength acoustic modes, transport coefficients from Green–Kubo relations, and two-phase systems. Moreover, meta exchange–correlation functionals, such as the strongly constrained and appropriately normed (SCAN) meta-generalized gradient approximation (meta-GGA), can provide a more accurate description of thermophysical properties than conventional GGA functionals, but at a substantially higher computational cost. For metallic systems, the increased cost per electronic-structure step together with more demanding self-consistent convergence can increase the overall computational expense by up to an order of magnitude, making direct QMD evaluation of thermophysical properties with sufficiently large cells and long trajectories impractical.

First-principles studies of sodium have addressed several distinct regions of the phase diagram and a variety of liquid-state properties. Qian et al. used DFT-based molecular dynamics to study self-diffusion in normal liquid Na and to determine its activation behavior [24]. Bickham et al. extended ab initio molecular dynamics to strongly expanded liquid states, where changes in local coordination and a pronounced decrease in the dc conductivity were found upon expansion [25]. First-principles simulations of the liquid–vapor interface subsequently revealed pronounced atomic layering near the triple point [26]. At high pressure, direct DFT molecular dynamics and DFT-trained neural-network potentials were used to investigate the anomalous melting curve and the structural, thermodynamic, and dynamical properties of dense liquid Na [27, 28, 29, 30, 31], while first-principles Kubo–Greenwood calculations provided the electrical and thermal conductivities of normal liquid at 400 K [32]. Ab initio Gibbs-ensemble Monte Carlo simulations mapped liquid–vapor coexistence between between 1.2 and 2.3 kK and yielded Tc=2.338(108)T_c = 2.338(108) kK and ρc=0.24(3)\rho_c = 0.24(3) g/cm3^3 [33]. More recently, direct DFT molecular dynamics has also been used to calculate self-diffusion and shear viscosity in compressed liquid Na [34].

The critical parameters of sodium have been estimated by a number of theoretical and semiempirical methods. The available values differ appreciably, especially for the critical density and pressure [35, 36, 37]. For example, an ab initio Gibbs-ensemble Monte Carlo calculation gives Tc=2.3(1)×103T_c = 2.3(1) \times10^3 K and ρc=0.24(3)\rho_c = 0.24(3) g/cm3^3 [33], while an analysis of liquid–vapor coexistence data gives ρc=0.18(1)\rho_c = 0.18(1) g/cm3^3 [35]. Enthalpies, heat capacities, and thermodynamic susceptibilities of the coexisting phases are reconstructed in Ref. [36], and high-temperature extrapolations of the sodium equation of state (EOS) are considered in Ref. [37].

These studies, however, generally focus on particular thermodynamic regimes or observables, and a single first-principles-based description combining the equation of state and its derivatives with phase boundaries, interfacial, acoustic, and transport properties from the normal liquid to the near-critical region has remained unavailable.

Machine-learned interatomic potentials provide a route to extending QMD to substantially larger length and time scales while retaining near-DFT accuracy. A particularly relevant example is the transferable machine-learned interatomic potential developed by Kumar et al. for aluminum, where a single potential was applied from ambient to warm-dense-matter conditions and used to calculate self-diffusion, shear viscosity, ionic thermal conductivity, sound velocity, and structural properties over an exceptionally broad temperature range [38]. Neural-network interatomic potentials have likewise been used to obtain transport coefficients in simulations requiring particularly long or computationally demanding trajectories, including path-integral calculations of hydrogen diffusion on Pd surfaces [39].

Deep neural-network interatomic potentials have also enabled large-scale simulations based on more computationally demanding exchange–correlation approximations. In particular, Luo et al. combined the Deep Potential framework with the SCAN meta-GGA functional to investigate structural and diffusive behavior of δ\delta-AlOOH over a broad range of mantle pressures and temperatures [40]. Temperature-dependent machine-learned interatomic potentials have further been developed for warm dense matter and systems with thermally excited electrons [41, 42, 43], while Deep Potential molecular dynamics has recently been applied to the liquid–vapor critical region of aluminum [44]. These studies establish complementary precedents for wide-range machine-learned interatomic potentials for metals, meta-GGA-based Deep Potential simulations, transport calculations, and liquid–vapor criticality. Nevertheless, a unified first-principles-based model that connects the normal and expanded liquid, liquid–vapor coexistence, and the critical region while simultaneously reproducing phase, caloric, acous-

tic, interfacial, and transport properties remains unexplored.

In this work, we use the Deep Potential method and its implementation in DeePMD-kit [45, 46] to construct temperature-dependent neural-network interatomic potentials for sodium that reproduce a broad range of thermophysical properties with near-experimental accuracy. In a finite-temperature DFT calculation, the forces and virials are determined from the electronic free energy using the Hellmann–Feynman theorem. A peculiarity of our approach is that, in addition to the free-energy potential, we construct a separate model of the electronic entropy, which is used to recover the internal energy. Thus, we developed PBE, AM05, and r2r^2SCAN deep potentials from finite-temperature DFT data. We also compare the critical parameters obtained with the three exchange–correlation functionals and use the r2r^2SCAN-based model for the remaining calculations.

Our paper is organized as follows. Section II introduces the computational methodology. Sections II A and II B describe the finite-temperature DFT reference calculations, configuration selection, and the construction and training of the Deep Potential models. Section II C provides the details of the molecular-dynamics simulations and the calculation of thermodynamic properties, while Sections II D, II E, II F, and II G describe the methods used to determine the critical point, sound velocity, phase boundaries and surface tension, and transport properties, respectively. Section III presents and discusses the calculated properties of sodium. Section III A presents the equation of state and critical-point analysis, Section III B discusses the enthalpy and heat capacities, and Section III C presents the thermal expansion, bulk moduli, Grüneisen parameter, and speed of sound. Phase boundaries and surface tension are discussed in Section III D, while the self-diffusion coefficient and shear viscosity are presented in Section III E. Finally, Section IV summarizes the main results.

Computational methods

DFT reference calculations and configuration selection

The reference free energies, forces, and virials are calculated with finite-temperature DFT using the Vienna Ab initio Simulation Package (VASP) [15, 16, 47, 48]. We use the projector augmented-wave (PAW) method with seven valence electrons [49, 50]. The electronic occupations are described by the Fermi–Dirac distribution, and the electronic and ionic temperatures are equal. Three exchange–correlation functionals are considered: the Perdew-Burke-Ernzerhof (PBE) parameterization [51, 52], the Armiento-Mattsson (AM05) parameterization [53], and r2r^2SCAN [54, 55]. The influence of the functional on the equilibrium volume and cohesive properties of alkali metals is discussed in Ref. [56]. The plane-wave cutoff is 800 eV to ensure the convergence of pressure and energy. The Brillouin zone is sampled by the Baldereschi mean-value point [57] for the largest low-density cells and by a 2×2×22 \times2 \times2 mesh for the smaller cells. All bands with occupations greater than 10−510^{-5} are included.

To generate a broad initial pool of atomic configurations, we first construct a preliminary machine-learning potential from an earlier set of PBE-based QMD simulations covering densities of ρ=0.05\rho= 0.05–0.900.90 g/cm3^{3} and temperatures of T=0.3T = 0.3–5.05.0 kK. These calculations employ a plane-wave cutoff of 500 eV. The ionic time step is 1–1.5 fs, and each trajectory contains at least 3000 production steps after equilibration. The statistical uncertainty of the averaged thermodynamic quantities is monitored and remains below 1%. Liquid-state simulations are performed with 128 atoms, except at the two lowest densities, ρ=0.10\rho= 0.10 and 0.05 g/cm3^{3}, where 54- and 32-atom cells are used, respectively. From these trajectories, 10 851 configurations are selected to train the preliminary potential. This model is then used to explore configuration space and generate candidate structures for the subsequent high-accuracy DFT calculations described above.

The common PBE, AM05, and r2SCANr^{2}\mathrm{SCAN} dataset contains 347 configurations in the ranges ρ=0.01\rho= 0.01–0.300.30 g/cm3^{3} and T=1T = 1–5 kK and is specifically constructed for a detailed study of the critical region. The simulation cells contain 16–128 atoms. In addition to the MD configurations, isotropically and anisotropically strained cells are included to sample the virial response. The r2SCANr^{2}\mathrm{SCAN} dataset is extended by 126 configurations at ρ=0.4\rho= 0.4–0.90.9 g/cm3^{3} and T=0.3T = 0.3–5.0 kK and by 286 configurations on a wider grid, ρ=0.02\rho= 0.02–1.00 g/cm3^{3} and T=0.2T = 0.2–5.0 kK. The complete r2SCANr^{2}\mathrm{SCAN} dataset contains 759 configurations (Figure 1).

Figure 1. Density–temperature points in the reference datasets. Circles denote the common 347-configuration PBE, AM05, and r2SCANr^{2}\mathrm{SCAN} set. Squares and triangles denote the 126- and 286-configuration r2SCANr^{2}\mathrm{SCAN} extensions, respectively.

Deep-potential architecture and training

We construct the DP-PBE, DP-AM05, and DP-r2SCANr^{2}\mathrm{SCAN} models using DeePMD-kit [46]. Each model is trained only on the data obtained with the corresponding exchange–correlation functional. We use the se_e2_a descriptor with a cutoff radius of 12 Å and a smoothing radius of 11.2 Å. The embedding network contains layers with 32, 64, and 128 neurons, and the fitting network contains three layers with 240 neurons. The electronic temperature is supplied as a frame parameter. The neighbor-selection parameter is 128 for DP-PBE and DP-AM05 and 384 for DP-r2SCANr^{2}\mathrm{SCAN}. The model parameters are summarized in Table 1.

ModelDP-PBEDP-AM05DP-r2r^{2}SCAN
Descriptorse_e2ase_e2ase_e2a
rcr_{\mathrm{c}} (Å)121212
rsmthr_{\mathrm{smth}} (Å)11.211.211.2
Embedding network32–64–12832–64–12832–64–128
Fitting network240–240–240240–240–240240–240–240
Frame parameters111
Neighbor selection128128384
ρ\rho range (g/cm3^{3})0.01–0.300.01–0.300.01–1.00
TT range (kK)1.0–5.01.0–5.00.2–5.0
Final steps5×1045 \times10^{4}10510^{5}5×1045 \times10^{4}
FF RMSE (meV/atom)1.802.153.53
Force RMSE (meV/Å)13.314.320.0
Virial RMSE (eV)0.2860.2820.679
PP RMSE (kbar)0.01490.01380.0623

Table 1. Architecture, training domain, and final fine-tuning parameters of the three deep potentials.

The models are obtained by successive fine-tuning of earlier checkpoints. The final PBE, AM05, and r2SCANr^{2}\mathrm{SCAN} stages contain 5×1045 \times10^{4}, 10510^{5}, and 5×1045 \times10^{4} optimization steps, respectively. The state points are sampled uniformly. The loss function is

L=pELE+pFLF+pΞLΞ,(1)\mathcal{L}=p_{E}\mathcal{L}_{E}+p_{F}\mathcal{L}_{F}+p_{\Xi}\mathcal{L}_{\Xi}, \tag*{(1)}

where Ξ\Xi is the virial. For the final PBE stage, (pE,pF,pΞ)(p_{E},p_{F},p_{\Xi}) changes from (0.1,1000,10)(0.1,1000,10) to (1,200,50)(1,200,50). The corresponding values are (0.001,100,10)(0.001,100,10) and (1,200,50)(1,200,50) for AM05 and (0.1,2000,1)(0.1,2000,1) and (10,50,10)(10,50,10) for r2SCANr^{2}\mathrm{SCAN}.

The DFT labels correspond to the electronic free energy FF. To recover the energy without the electronic-entropy term, E0E_{0}, we train a separate intensive-property model for sel=Sel/(NkB)s_{\mathrm{el}}=S_{\mathrm{el}}/(Nk_{\mathrm{B}}). The descriptor is transferred from DP-r2SCANr^{2}\mathrm{SCAN}, and a new three-layer property network is trained on the 759 configurations for 10510^{5} steps. The reference entropy is calculated as Sel=−(F−E0)/TS_{\mathrm{el}}=-(F-E_{0})/T, and

E0pred=Fpred+NkBTselpred.(2)E_{0}^{\mathrm{pred}}=F^{\mathrm{pred}}+Nk_{\mathrm{B}}Ts_{\mathrm{el}}^{\mathrm{pred}}. \tag*{(2)}

This model is used only to calculate the entropy contribution. The forces and virials during the molecular dynamics (MD) simulations are calculated with the free-energy model.

For DP-r2SCANr^{2}\mathrm{SCAN}, the RMSE values are 3.5 meV/atom for F/NF/N, 20.0 meV/Å for the force components, and 0.062 kbar for pressure (Figure 2). The RMSE of the entropy model for Tsel/NTs_{\mathrm{el}}/N is 2.6 meV/atom. The relative pressure RMSE does not exceed 3.5% for ρ≥0.05\rho\ge0.05 g/cm3^{3} but reaches 99% at ρ=0.01\rho= 0.01 g/cm3^{3}, mainly because of two configurations at 3 kK. The lowest-density states are therefore used only for a qualitative construction of the phase diagram.

Figure 2. DP-r2r^{2}SCAN results for the 759-configuration training set: (a) free energy per atom, (b) Cartesian force components, (c) pressure, and (d) electronic entropy contribution per atom. The solid lines correspond to exact agreement.

Molecular-dynamics simulations and thermodynamic properties

Classical MD simulations are performed by LAMMPS [58] using periodic boundary conditions (PBC) with 1 fs time step. Unless stated otherwise, the cubic cell contains 2000 atoms. The EOS is calculated in the NVTNVT ensemble with a Nosé–Hoover thermostat and a damping time of 0.1 ps [59]. Each state is equilibrated for 20 ps and sampled for 50 ps. Configurations for the energy and entropy calculations are stored every 10 steps.

The statistical errors of pressure, energy, and electronic entropy are estimated using block averaging. For pressure, the standard error is calculated as

σP=[1nb(nb−1)∑b=1nb(P‾b−⟨P⟩)2]1/2,(3)\sigma_P = \left[\frac{1}{n_b(n_b-1)}\sum_{b=1}^{n_b}\left(\overline{P}_b-\langle P\rangle\right)^2\right]^{1/2}, \tag*{(3)}

where nb=10n_b = 10, P‾b\overline{P}_b is the block average and ⟨P⟩\langle P\rangle is the mean pressure. Hereafter, the angle brackets are omitted.

The energy provided by DeePMD is the electronic free energy FF. The total energy is calculated as

E=F+TSel+32NkBT=F+NkBTsel+32NkBT,(4)E = F + T S_{\mathrm{el}} + \frac{3}{2}Nk_{\mathrm{B}}T = F + Nk_{\mathrm{B}}T s_{\mathrm{el}} + \frac{3}{2}Nk_{\mathrm{B}}T, \tag*{(4)}

where sel=Sel/(NkB)s_{\mathrm{el}} = S_{\mathrm{el}}/(Nk_{\mathrm{B}}).

The thermodynamic properties are obtained from polynomial approximations of P(E)∣ρP(E)|_{\rho} and T(E)∣ρT(E)|_{\rho}. At a given pressure P∗P^{*}, the isobar is found from the equation P(E,ρ)=P∗P(E,\rho)=P^{*}. The derivatives are evaluated analytically from polynomial fits. The enthalpy is

H(ρ,T)=E(ρ,T)+P(ρ,T)V,V=NMNAρ,(5)H(\rho,T)=E(\rho,T)+P(\rho,T)V,\qquad V=\frac{NM}{N_{\mathrm{A}}\rho}, \tag*{(5)}

where MM is the molar mass of sodium. The heat capacities are calculated as

CV=(∂E∂T)V,CP=(∂H∂T)P.(6)C_V=\left(\frac{\partial E}{\partial T}\right)_V,\qquad C_P=\left(\frac{\partial H}{\partial T}\right)_P. \tag*{(6)}

The isobaric expansion coefficient and the Grüneisen parameter are

αP=−1ρ(∂ρ∂T)P=−1ρ(∂T/∂ρ)P,(7)\alpha_P=-\frac{1}{\rho}\left(\frac{\partial\rho}{\partial T}\right)_P=-\frac{1}{\rho(\partial T/\partial\rho)_P}, \tag*{(7)}
γ=V(∂P∂E)V.(8)\gamma=V\left(\frac{\partial P}{\partial E}\right)_V. \tag*{(8)}

The adiabatic bulk modulus and compressibility are obtained from the thermodynamic speed of sound,

KS=ρcs,th2,κS=KS−1,(9)K_S=\rho c_{s,\mathrm{th}}^2,\qquad\kappa_S=K_S^{-1}, \tag*{(9)}

and the isothermal quantities are calculated from

κT=κS+TαP2ρCP,KT=κT−1.(10)\kappa_T=\kappa_S+\frac{T\alpha_P^2}{\rho C_P},\qquad K_T=\kappa_T^{-1}. \tag*{(10)}

Here, CPC_P denotes the mass-specific isobaric heat capacity. We also use

KS=KTCPCV.(11)K_S=K_T\frac{C_P}{C_V}. \tag*{(11)}

Statistical errors are propagated using 250 bootstrap realizations. In each realization, pressure and energy at every state point are varied within their block standard errors, after which the isobars and the derivative quantities are recalculated.

Critical-point determination

The critical point is obtained from the pressure surface calculated in the NVTNVT simulations. The construction is based on the approach used in our previous QMD studies [?, 23, 60]. First, the pressure along each isochore is approximated as a function of temperature. The resulting fits are then used to reconstruct the pressure isotherms in the PP–ρ\rho plane. The critical isotherm has a stationary inflection point (see Figure 3).

Figure 3. (a) Subcritical and critical isotherms in the PP–ρ\rho plane. (b) Corresponding isobars in the ρ\rho–TT plane. The curves are schematic.

For each density ρi\rho_i, the pressure is approximated by

Pi(T)=ai0+ai1T+ai2T2.(12)P_i(T) = a_{i0} + a_{i1}T + a_{i2}T^2. \tag*{(12)}

The fits are evaluated on a uniform grid of 800 temperatures. At each temperature, the calculated set {Pi(T),ρi}\{P_i(T), \rho_i\} is approximated by a cubic polynomial,

P(ρ;T)=c0(T)+c1(T)ρ+c2(T)ρ2+c3(T)ρ3.(13)P(\rho; T) = c_0(T) + c_1(T)\rho+ c_2(T)\rho^2 + c_3(T)\rho^3. \tag*{(13)}

The inflection density is

ρ∗(T)=−c2(T)3c3(T),(14)\rho_*(T) = -\frac{c_2(T)}{3c_3(T)}, \tag*{(14)}

provided that it lies within the fitted density interval. The critical conditions are

(∂P∂ρ)T=0,(∂2P∂ρ2)T=0.(15)\left(\frac{\partial P}{\partial\rho}\right)_T = 0, \qquad\left(\frac{\partial^2 P}{\partial\rho^2}\right)_T = 0. \tag*{(15)}

We therefore minimize

M(T)=∣∂P∂ρ∣ρ=ρ∗(T)∣.(16)\mathcal{M}(T) = \left|\left.\frac{\partial P}{\partial\rho}\right|_{\rho=\rho_*(T)}\right|. \tag*{(16)}

The minimum gives TcT_c, ρc=ρ∗(Tc)\rho_c = \rho_*(T_c), and Pc=P(ρc;Tc)P_c = P(\rho_c; T_c). The procedure is tested with the reduced van der Waals equation,

Pr=8Trρr3−ρr−3ρr2,(17)P_r = \frac{8T_r\rho_r}{3-\rho_r} - 3\rho_r^2, \tag*{(17)}

whose critical coordinates are equal to unity. For 0.90≤ρr≤1.100.90 \le\rho_r \le1.10 and 0.98≤Tr≤1.050.98 \le T_r \le1.05, the fitted deviations are Tr,c−1=3×10−6T_{r,c} - 1 = 3 \times10^{-6}, ρr,c−1=−1.5×10−3\rho_{r,c} - 1 = -1.5 \times10^{-3}, and Pr,c−1=6×10−6P_{r,c} - 1 = 6 \times10^{-6}.

For sodium, the critical-point fits use 0.15≤ρ≤0.260.15 \le\rho\le0.26 g/cm3^3. The temperature intervals are 2100–2400 K for DP-PBE and DP-AM05, and 2440–2600 K for DP-r2r^2SCAN. Statistical errors are calculated from 500 bootstrap realizations in which the pressure at each state point is varied within its block standard error.

Sound-velocity calculation

The adiabatic speed of sound is calculated from the EOS and directly from the propagation of a longitudinal acoustic mode. Along the normal-pressure (1 bar) isobar up to the normal boiling temperature and along the critical isobar, the thermodynamic value is obtained from

cs,th2=(∂P∂ρ)S=KSρ=γcPαP,(18)c_{s,\mathrm{th}}^2 = \left(\frac{\partial P}{\partial\rho}\right)_S = \frac{K_S}{\rho} = \frac{\gamma c_P}{\alpha_P}, \tag*{(18)}

where cPc_P is the mass-specific heat capacity. This relation is also used in Refs. [61, 62].

To verify thermodynamic consistency, we also use a direct method for calculating the speed of sound. For the direct calculation [63], the 2000-atom cubic cell is replicated four times along the xx direction. The resulting 8000-atom cell is equilibrated for 50 ps in the NVTNVT ensemble. The thermostat is then removed, and the longitudinal perturbation

vx(x,0)=u0sin⁡(kx),u0=0.2 A˚/ps,k=2πLx(19)v_x(x,0) = u_0 \sin(kx), \qquad u_0 = 0.2\ \text{\AA}/\text{ps}, \qquad k = \frac{2\pi}{L_x} \tag*{(19)}

is applied. The system is subsequently simulated for 150 ps in the microcanonical ensemble.

The fundamental mode is determined from the velocity and density projections

Js(t)=⟨vxsin⁡(kx)⟩,Jc(t)=⟨vxcos⁡(kx)⟩,J_s(t) = \langle v_x \sin(kx)\rangle,\qquad J_c(t) = \langle v_x \cos(kx)\rangle,
Rs(t)=⟨sin⁡(kx)⟩,Rc(t)=⟨cos⁡(kx)⟩.(20)R_s(t) = \langle\sin(kx)\rangle,\qquad R_c(t) = \langle\cos(kx)\rangle. \tag*{(20)}

The four projections are fitted simultaneously by damped harmonic functions with a common angular frequency ω\omega and damping rate. The finite-wave-number phase velocity is

cs,dir=ωk=fLx,(21)c_{s,\mathrm{dir}} = \frac{\omega}{k} = fL_x, \tag*{(21)}

where f=ω/(2π)f = \omega/(2\pi) and k=2π/Lxk = 2\pi/L_x. For the example shown in Figure 4, f=0.06354/psf = 0.06354/\text{ps} and Lx=213.80L_x = 213.80 Å, which gives cs,dir=1358c_{s,\mathrm{dir}} = 1358 m/s.

Figure 4. Direct speed-of-sound calculation at ρ=0.5\rho= 0.5 g/cm3^3 and T=2112T = 2112 K (critical isobar). (a) Fundamental longitudinal velocity field reconstructed from Js(t)J_s(t) and Jc(t)J_c(t). (b) Velocity and density projections from Eq. (20). Symbols are MD data, and lines are the joint fits over 10–50 ps.

Only the interval in which the fundamental mode remains coherent is used. The fitting interval is varied between 18 and 30 ps and shifted by 2 ps. The standard deviation of the resulting velocities is taken as the internal uncertainty.

Phase-boundary calculations

A segment of the melting curve near atmospheric pressure is determined from direct solid–liquid coexistence simulations in the NVTNVT ensemble. The fixed-volume periodic cell contains 19800 atoms, with equal solid and liquid parts. The liquid part is prepared at 600 K while the solid part is fixed; the solid is then released, and the whole cell is simulated at the target temperature with a Nosé–Hoover thermostat. The first 10 ps are discarded, followed by a 50 ps production run.

Solid-like atoms are identified using the local bcc order with a centrosymmetry parameter below 3.0. From the solid-fraction profile s(z,t)s(z,t), we calculate

Ls(t)=∫s(z,t) dz,vint=12dLsdt,(22)L_s(t) = \int s(z,t)\,dz,\qquad v_{\mathrm{int}} = \frac{1}{2}\frac{dL_s}{dt}, \tag*{(22)}

where the factor 1/21/2 accounts for the two interfaces (due to PBC). Positive and negative vintv_{\mathrm{int}} correspond to freezing and melting, respectively. For each density, TmT_m is obtained by linear interpolation to vint=0v_{\mathrm{int}} = 0 [64]. The corresponding PmP_m is determined from the interpolated pressure-tensor component PzzP_{zz} normal to the interface. Statistical uncertainties are propagated by Monte Carlo sampling of the block errors of vintv_{\mathrm{int}} and PzzP_{zz}.

Liquid–vapor coexistence is simulated in a rectangular periodic cell containing 11 664 atoms with the mean density 0.19 g/cm3^3. A liquid slab normal to the zz axis forms two liquid–vapor interfaces [65]. The cell volume is fixed. The calculations are performed at several temperatures between 496 and 2480 K. The low-temperature states are initialized independently. Starting from 2100 K, each state is initialized from the equilibrated configuration at the preceding temperature. Each system is equilibrated for 250 ps and sampled for 500 ps in the NVTNVT ensemble. The density profile is accumulated in 1 Å bins and recentered using the phase of its first Fourier component. The block-averaged profile is approximated by [66]

ρ(z)=ρv+ρl−ρv2[tanh⁡(z−z1d1)−tanh⁡(z−z2d2)],(23)\rho(z) = \rho_v + \frac{\rho_l-\rho_v}{2}\left[\tanh\left(\frac{z-z_1}{d_1}\right)-\tanh\left(\frac{z-z_2}{d_2}\right)\right], \tag*{(23)}

where ρl\rho_l and ρv\rho_v are the coexistence densities, z1z_1 and z2z_2 are the interface positions, and d1d_1 and d2d_2 are the interface-width parameters.

The surface tension is calculated from the pressure-tensor anisotropy [67],

σ=Lz2[Pzz−Pxx+Pyy2].(24)\sigma= \frac{L_z}{2}\left[P_{zz}-\frac{P_{xx}+P_{yy}}{2}\right]. \tag*{(24)}

The pressure-tensor components are stored every 5 fs. The standard error of σ\sigma is calculated from eight 50-ps blocks after discarding the first 100 ps of the production interval. Errors of the coexistence densities and interface parameters are obtained from ten profile blocks.

Transport properties

The self-diffusion coefficient and shear viscosity are calculated with DP-r2r^2SCAN along the critical isobar from calculations along the isochores. The self-diffusion coefficient is obtained from the long-time slope of the meansquared displacement,

D=lim⁡t→∞16t⟨1N∑i=1N∣ri(t0+t)−ri(t0)∣2⟩t0.(25)D = \lim_{t \to\infty} \frac{1}{6t}\left\langle\frac{1}{N}\sum_{i=1}^{N}\left|\mathbf{r}_{i}(t_{0}+t)-\mathbf{r}_{i}(t_{0})\right|^{2}\right\rangle_{t_{0}} . \tag*{(25)}

The trajectories are unwrapped across periodic boundaries before the mean-squared displacement is calculated.

The shear viscosity is calculated from the Green–Kubo relation,

ηαβ(t)=VkBT∫0t⟨δPαβ(0)δPαβ(t′)⟩ dt′,(26)\eta_{\alpha\beta}(t)=\frac{V}{k_{\mathrm{B}}T}\int_{0}^{t}\left\langle\delta P_{\alpha\beta}(0)\delta P_{\alpha\beta}(t')\right\rangle\,\mathrm{d}t', \tag*{(26)}

αβ∈{xy,xz,yz}\alpha\beta\in\{xy,xz,yz\},

where δPαβ=Pαβ−⟨Pαβ⟩\delta P_{\alpha\beta}=P_{\alpha\beta}-\langle P_{\alpha\beta}\rangle. For each state, eight independent NVTNVT simulations containing 2000 atoms are performed with a time step of 0.5 fs. The equilibration and production times are 25 and 200 ps, respectively; the equilibration time is increased to 50 ps in the critical region. The stress tensor is stored every 5 fs.

The three off-diagonal running integrals are averaged as

η(t)=13[ηxy(t)+ηxz(t)+ηyz(t)].(27)\eta(t)=\frac{1}{3}\left[\eta_{xy}(t)+\eta_{xz}(t)+\eta_{yz}(t)\right]. \tag*{(27)}

The viscosity is determined from the mean value over the 8–20 ps plateau. The integration interval is varied between 6 and 20 ps.

Results and discussion

Equation of state and critical point

The equilibrium density of bcc sodium at 300 K is determined from eight NVTNVT calculations in the interval ρ=0.965\rho=0.965–0.9720.972 g/cm3^{3}. In this interval, the pressure is approximated by

P(ρ)=Aρ+B.(28)P(\rho)=A\rho+B. \tag*{(28)}

Here, PP is in kbar and ρ\rho is in g/cm3^{3}. The coefficients are A=66.81A=66.81 kbar cm3^{3}/g and B=−64.61B=-64.61 kbar. The normal-pressure density is ρ0=0.96709\rho_{0}=0.96709 g/cm3^{3} (lattice parameter a0=4.28992a_{0}=4.28992 Å). The density obtained from the experimental lattice parameter a0=4.2908a_{0}=4.2908 Å at 298 K is 0.96649 g/cm3^{3} [68, 69]. Thus, the difference between the calculated and experimental values is 0.06%.

Using DP-r2r^{2}SCAN, we calculate pressure and internal energy on a grid of isochores. Figure 5 shows the pressure as a function of temperature. The quadratic approximations of these isochores are used below to reconstruct the isotherms and determine the critical point. The complete EOS data are provided in the Supplemental Material [70].

Figure 5. Pressure–temperature isochores calculated with DP-r2r^{2}SCAN. Legend entries give the density in g/cm3^{3}. Symbols are NVTNVT averages, and solid lines are the quadratic approximations used to reconstruct the isotherms. Error bars are smaller than the symbol size.

Figure 6 shows the reconstructed r2r^{2}SCAN isotherms in the vicinity of the critical point. The stationary-inflection method described in Sec. II D gives

Figure 6. Sodium pressure isotherms for DP-r2r^{2}SCAN near the critical point. Symbols are NVTNVT averages, solid curves are reconstructed from the isochore approximations, and the dashed curve is the critical isotherm. The star, hexagon, and diamond denote the r2r^{2}SCAN, PBE, and AM05 critical points, respectively.

Tc=2508(8) K,ρc=0.203(4) g/cm3,T_{\mathrm{c}}=2508(8)\ \mathrm{K},\qquad\rho_{\mathrm{c}}=0.203(4)\ \mathrm{g/cm}^{3},
Pc=0.249(6) kbar.(29)P_{\mathrm{c}}=0.249(6)\ \mathrm{kbar}. \tag*{(29)}

The corresponding critical compressibility factor is Zc=0.135(4)Z_{\mathrm{c}}=0.135(4).

The same procedure gives Tc=2197(4)T_{\mathrm{c}}=2197(4) K, ρc=0.1773(7)\rho_{\mathrm{c}}=0.1773(7) g/cm3^{3}, and Pc=0.204(2)P_{\mathrm{c}}=0.204(2) kbar for DP-PBE. For DP-AM05, we obtain Tc=2183(3)T_{\mathrm{c}}=2183(3) K, ρc=0.202(1)\rho_{\mathrm{c}}=0.202(1) g/cm3^{3}, and Pc=0.245(2)P_{\mathrm{c}}=0.245(2) kbar. Thus, the PBE and AM05 GGA exchange–correlation functionals yield similar critical temperatures, both about 12% below the Fink–Leibowitz recommendation, although their critical densities differ substantially. In contrast, the meta-GGA r2r^2SCAN functional gives a critical temperature close to the recommended value (Table II). For the critical density and pressure, DP-PBE gives the lowest values, whereas DP-AM05 and DP-r2r^2SCAN are very close to each other and show good agreement with the recommended data. The literature estimates in Table II vary from 2.3 to 2.80 kK for the critical temperature, from 0.153 to 0.271 g/cm3^3 for the critical density, and from 0.18 to 0.92 kbar for the critical pressure.

After the critical point is determined, the liquid branch of the critical isobar is calculated (see Figure 7) and approximated by

Density–temperature phase diagram of sodium calculated with DP-r$^{2}$SCAN

Figure 7. Density–temperature phase diagram of sodium calculated with DP-r2^{2}SCAN. The red star denotes the critical point. The red, blue, and violet curves are the P=0.25P = 0.25 kbar, normal-pressure, and P=0.46P = 0.46 kbar isobars, respectively. Gray circles are the calculated liquid–vapor coexistence densities. The light-gray curve shows the Fink–Leibowitz binodal [6]; saturation-line data from Bystrov et al., Shpil’rain et al., and Hornung are also shown [75, 85, 86]. The Vargaftik data correspond to the P=470P = 470 kgf/cm2^{2} (0.460.46 kbar) isobar [84]. The Touloukian curve is obtained from the recommended linear thermal-expansion data for solid sodium [87]. Symbols denote selected literature data and critical-point estimates identified in the legend (see Table 2). Vertical dashed lines mark the experimental normal melting and boiling temperatures.

ρ(T)=ρc+C1u+C2u2+C3u3+C4u4+C5u5,P=Pc,(30)\rho(T) = \rho_c + C_1u + C_2u^2 + C_3u^3 + C_4u^4 + C_5u^5,\qquad P = P_c, \tag*{(30)}

where u=(Tc−T)1/3u = (T_c - T)^{1/3}, with both TT and TcT_c expressed in kK, and ρ\rho is in g/cm3^3. The coefficient CnC_n is in g/(cm3^3 kKn/3^{n/3}). The coefficients are C1=0.1669C_1 = 0.1669, C2=0.9729C_2 = 0.9729, C3=−1.731C_3 = -1.731, C4=1.432C_4 = 1.432, and C5=−0.3782C_5 = -0.3782. The approximation is used in the interval 0.380 kK ≤T<Tc\le T < T_c.

Figure 7 summarizes the density–temperature phase diagram obtained with DP-r2r^2SCAN. The calculated atmospheric-pressure isobar agrees closely with the available literature data from the vicinity of the melting point up to the normal boiling temperature. The P=0.46P = 0.46 kbar isobar also follows the data of Vargaftik [84]. The calculated coexistence densities reproduce the overall shape of the liquid–vapor binodal and are close to the Fink–Leibowitz [6] correlation over both branches. Near the critical region, the present DP-r2r^2SCAN critical point lies within the broad scatter of previous estimates and close to the recommended values listed in Table 2. The coexistence calculations are discussed in Sec. III D.

SourceTcT_c (kK)ρc\rho_c (g/cm3^3)PcP_c (kbar)
DP-r2r^2SCAN, this work2.508(8)0.203(4)0.249(6)
DP-PBE, this work2.197(4)0.1773(7)0.204(2)
DP-AM05, this work2.183(3)0.202(1)0.245(2)
Gathers [71]2.4290.1650.3
Fortov et al. [72]2.5730.2060.28
Young and Alder [73]2.6350.2710.92
Petiot and Seiler [74]2.63(5)0.2050.34(4)
Hornung [75]2.5730.2210.35
Lomonosov [76]2.4730.240.466
Levashov [77]2.4360.1860.363
Morris [78]2.80.153—
Vargaftik [79]2.5—0.18
Thurnay [80]2.5080.230.2565
Ohse et al. [81]2.50(2)0.211(2)0.252(6)
Fink and Leibowitz [6]2.50(1)0.22(2)0.256(4)
Sobolev [5]2.50(1)0.22(2)0.256(4)
IVTANTHERMO [7]2.50(5)0.21(4)0.256(2)
Vazquez et al. [35]—0.18(1)—
Li et al. [33]2.3(1)0.24(3)—
Barnes (estimated) [82]2.7330.17960.413
Mozgovoi et al. [83]2.503(50)0.207(30)0.256(15)

Table 2. Critical parameters of sodium from this work and literature. Parentheses denote the reported uncertainties.

Enthalpy and heat capacities

Figure 8 shows the calculated enthalpy of bcc and liquid sodium at atmospheric pressure and of liquid sodium along the critical isobar. For bcc sodium, the normal-pressure enthalpy in the interval 0.25 kK≤T≤Tmexp0.25\ {\rm kK} \le T \le T_{\rm m}^{\rm exp} is approximated by

Relative enthalpy of bcc and liquid sodium at normal pressure and of liquid sodium along the critical isobar

Figure 8. Relative enthalpy of bcc and liquid sodium at normal pressure and of liquid sodium along the critical isobar. Symbols denote the DP-r2r^{2}SCAN results. The blue and red curves represent the normal-pressure and critical-isobar dependences, respectively. The dashed blue segment extends the liquid normal-pressure branch from 380 K to the experimental melting temperature TmT_{\mathrm{m}}. The green dashed, cyan solid, and magenta dotted curves show the NIST–JANAF, Gurvich–IVTANTHERMO, and Sobolev reference dependences, respectively [5, 7, 88]. The inset enlarges the region near TmT_{\mathrm{m}}. Vertical dotted lines mark TmT_{\mathrm{m}}, the normal boiling temperature TbT_{\mathrm{b}}, and the critical temperature TcT_{\mathrm{c}}.

H0(T)−H0(300 K)=D1θ0+D2[exp⁡(D3θ0)−1],(31)H_0(T) - H_0(300\ {\rm K}) = D_1\theta_0 + D_2[\exp(D_3\theta_0)-1], \tag*{(31)}

where θ0=T−0.3\theta_0 = T - 0.3, TT in kK, and the coefficients are D1=24.9434 kJ mol−1 K−1D_1 = 24.9434\ {\rm kJ\ mol}^{-1}\ {\rm K}^{-1}, D2=0.34802 kJ/molD_2 = 0.34802\ {\rm kJ/mol}, and D3=9.47319 kK−1D_3 = 9.47319\ {\rm kK}^{-1}. The corresponding isobaric heat capacity is obtained by differentiating (31),

C0bcc(T)=D1+D2D3exp⁡(D3θ0).(32)C_0^{\rm bcc}(T) = D_1 + D_2D_3\exp(D_3\theta_0). \tag*{(32)}

The liquid ambient-pressure enthalpy is approximated over Tmexp≤T≤TbT_{\rm m}^{\rm exp} \le T \le T_b by

H0(T)−H0(300 K)=F0+F1θ0+F2θ02+F3θ03H_0(T) - H_0(300\ {\rm K}) = F_0 + F_1\theta_0 + F_2\theta_0^2 + F_3\theta_0^3
+F4exp⁡(F5θ0).(33){}+ F_4\exp(F_5\theta_0). \tag*{(33)}

Here, Tb=1156T_b = 1156 K denotes the normal boiling temperature of sodium. The coefficients are F0=2.62020 kJ/molF_0 = 2.62020\ {\rm kJ/mol}, F1=32.7395 kJ mol−1 K−1F_1 = 32.7395\ {\rm kJ\ mol}^{-1}\ {\rm K}^{-1}, F2=−4.53996 kJ mol−1 kK−2F_2 = -4.53996\ {\rm kJ\ mol}^{-1}\ {\rm kK}^{-2}, F3=2.30458 kJ mol−1 kK−3F_3 = 2.30458\ {\rm kJ\ mol}^{-1}\ {\rm kK}^{-3}, F4=8.517×10−11 kJ/molF_4 = 8.517 \times10^{-11}\ {\rm kJ/mol}, and F5=12.4737 kK−1F_5 = 12.4737\ {\rm kK}^{-1}.

Over the same interval, differentiation of (33) gives

C0(T)=F1+2F2θ0+3F3θ02+F4F5exp⁡(F5θ0).(34)C_0(T) = F_1 + 2F_2\theta_0 + 3F_3\theta_0^2 + F_4F_5\exp(F_5\theta_0). \tag*{(34)}

Eqs. (32) and (34) give CPC_P directly in J mol−1^{-1} K−1^{-1}. The calculated bcc enthalpy agrees with the reference data (see Figure 8). In the liquid state, the calculated curve has a slightly larger slope than the experimental and recommended dependences. At the experimental melting temperature, the calculated fusion enthalpy is ΔHm=2.82\Delta H_{\rm m} = 2.82 kJ/mol, which is 9% above the IVTANTHERMO value 2.598(5) kJ/mol [7]. The inset in Fig. 8 shows that the difference is mainly caused by the calculated liquid enthalpy at melting, whereas the enthalpy of bcc sodium is in excellent agreement with the literature data.

Along the critical isobar, the temperature dependence of enthalpy in the interval 0.5 kK≤T<Tc0.5\ {\rm kK} \le T < T_c is described by

HP=Pc(T)−HP=Pc(300 K)=G0+G1θc+G2θc2+G3θc3H_{P=P_c}(T) - H_{P=P_c}(300\ {\rm K}) = G_0 + G_1\theta_c + G_2\theta_c^2 + G_3\theta_c^3
+G4θc4+G5(−θcTc)6,(35){}+ G_4\theta_c^4 + G_5\left(-\frac{\theta_c}{T_c}\right)^6, \tag*{(35)}

where θc=T−Tc\theta_c = T - T_c, TT and Tc=2.50849T_c = 2.50849 are in kK. The coefficients are G0=99.8105G_0 = 99.8105 kJ/mol, G1=19.1072G_1 = 19.1072 kJ mol−1^{-1} kK−1^{-1}, G2=−8.37354G_2 = -8.37354 kJ mol−1^{-1} kK−2^{-2}, G3=−5.67561G_3 = -5.67561 kJ mol−1^{-1} kK−3^{-3}, G4=−1.35200G_4 = -1.35200 kJ mol−1^{-1} kK−4^{-4}, G5=−43.2970G_5 = -43.2970 kJ/mol, and G6=0.2G_6 = 0.2. The polynomial contribution describes the regular temperature dependence, whereas the last term accounts for the rapid increase near the critical point.

Differentiation of (35) gives the isobaric heat capacity,

CP=Pc(T)=G1+2G2θc+3G3θc2+4G4θc3−G5G6Tc(−θcTc)G6−1.(36)C_P = P_c(T) = G_1 + 2G_2\theta_c + 3G_3\theta_c^2 + 4G_4\theta_c^3 - \frac{G_5G_6}{T_c}\left(\frac{-\theta_c}{T_c}\right)^{G_6-1}. \tag*{(36)}

Again, (36) gives CPC_P directly in J mol−1^{-1} K−1^{-1}. Near the critical point, CP∝(−θc/Tc)−0.8C_P \propto(-\theta_c/T_c)^{-0.8}, whereas enthalpy remains finite and approaches its critical value as Hc−H(T)∝(−θc/Tc)0.2H_c - H(T) \propto(-\theta_c/T_c)^{0.2}. This approximation is used below together with the density and Grüneisen-parameter dependences to calculate the speed of sound.

In Figure 8, the enthalpy results are compared with the Sobolev, NIST–JANAF, and Gurvich–IVTANTHERMO correlations [5, 7, 88]. In Figure 9, the heat-capacity results are compared with the Kirillov (2008), Gurvich–IVTANTHERMO, and Ginnings dependences [7, 9, 89]. Up to approximately 1.15 kK, the calculated liquid enthalpy increases slightly faster than the reference curves. At normal pressure, the calculated CPC_P agrees with the recommended dependences. Along the critical isobar, CPC_P increases rapidly as TcT_c is approached.

Isobaric heat capacity along the atmospheric-pressure and critical isobars

Figure 9. Isobaric heat capacity along the atmospheric-pressure and critical isobars. The blue and red curves are the present DP-r2r^{2}SCAN results along the atmospheric-pressure and critical isobars, respectively. The magenta dashed, black dash-dotted, and green dotted curves correspond to the Kirillov (2008) recommendation as compiled by Sobolev, Gurvich–IVTANTHERMO, and Ginnings et al. (1950), respectively [5, 7, 9, 89]. The inset enlarges the region near the normal melting temperature TmT_{\mathrm{m}} and shows the discontinuity in CPC_{P} between the solid and liquid branches. Vertical dotted lines in the main panel mark TmT_{\mathrm{m}}, the normal boiling temperature TbT_{\mathrm{b}}, and the critical temperature TcT_{\mathrm{c}}.

The isochoric heat capacity is calculated from E(T)∣ρE(T)|_{\rho} as

CV=(∂E∂T)V.(37)C_V = \left(\frac{\partial E}{\partial T}\right)_V. \tag*{(37)}

Along the critical isobar, its temperature dependence is approximated in the range 0.5 kK ≤T<Tc\le T < T_{\mathrm{c}} by

CV,P=Pc(T)=A0+A1θc+A2θc2+A3θc3+A4(−θc)A5.(38)C_{V,P=P_{\mathrm{c}}}(T) = A_{0} + A_{1}\theta_{\mathrm{c}} + A_{2}\theta_{\mathrm{c}}^{2} + A_{3}\theta_{\mathrm{c}}^{3} + A_{4}(-\theta_{\mathrm{c}})^{A_{5}}. \tag*{(38)}

Here, θc=T−Tc\theta_{\mathrm{c}} = T - T_{\mathrm{c}}, with TT and TcT_{\mathrm{c}} expressed in kK. The coefficients are A0=0.321182 kB/atomA_{0} = 0.321182\ k_{\mathrm{B}}/\mathrm{atom}, A1=−0.394858 kB atom−1 kK−1A_{1} = -0.394858\ k_{\mathrm{B}}\ \mathrm{atom}^{-1}\ \mathrm{kK}^{-1}, A2=−0.137804 kB atom−1 kK−2A_{2} = -0.137804\ k_{\mathrm{B}}\ \mathrm{atom}^{-1}\ \mathrm{kK}^{-2}, A3=−0.141090 kB atom−1 kK−3A_{3} = -0.141090\ k_{\mathrm{B}}\ \mathrm{atom}^{-1}\ \mathrm{kK}^{-3}, A4=1.66122 kB atom−1 kK0.11A_{4} = 1.66122\ k_{\mathrm{B}}\ \mathrm{atom}^{-1}\ \mathrm{kK}^{0.11}, and A5=−0.11A_{5} = -0.11. The resulting CVC_{V} is expressed in kB/atomk_{\mathrm{B}}/\mathrm{atom}. The regular cubic contribution reproduces the broad minimum in the liquid region and the low-temperature slope, whereas the last term describes the increase toward the critical point.

Figure 10 shows the temperature dependence of the isochoric heat capacity along the normal-pressure and critical isobars in comparison with the recommended data of Fink and Leibowitz [6]. At low temperatures, the two calculated isobars are nearly indistinguishable and agree with the recommended dependence within its uncertainty up to the boiling temperature. Above TbT_{\mathrm{b}}, the normal-pressure liquid branch is no longer an equilibrium state; along the critical isobar, CVC_{V} exhibits a pronounced rise as TcT_{\mathrm{c}} is approached. The uncertainty of the recommended data increases rapidly in the expanded-liquid and near-critical regions.

Figure 10. Isochoric heat capacity along the ambient-pressure and critical isobars. Symbols are obtained from the calculated EOS. The critical-isobar curve is described by (38). The black curve and gray band show the Fink–Leibowitz recommendation and its uncertainty [6].

Thermal expansion, bulk moduli, Grüneisen parameter, and speed of sound

The isobaric thermal expansion coefficient, αP\alpha_{P}, and the bulk moduli are calculated from the reconstructed EOS along the atmospheric-pressure and critical isobars. Figure 11 shows the temperature dependence of αP\alpha_{P}. At low temperatures, the two isobars are nearly indistinguishable and agree closely with the normal-pressure Sobolev recommendation [5]. Along the atmospheric-pressure isobar, αP\alpha_{P} increases from 2.5×10−4 K−12.5 \times10^{-4}\ \mathrm{K}^{-1} at melting to 3.3×10−4 K−13.3 \times10^{-4}\ \mathrm{K}^{-1} at the normal boiling temperature TbT_{b}. Along the critical isobar, the increase becomes substantially stronger near the critical region, reaching 5.24×10−3 K−15.24 \times10^{-3}\ \mathrm{K}^{-1} at 2.493 kK2.493\ \mathrm{kK}. The rapid growth of αP\alpha_{P} reflects the increasing sensitivity of the density to temperature as the critical point is approached.

Isobaric thermal expansion coefficient of sodium along the ambient-pressure and critical isobars

Figure 11. Isobaric thermal expansion coefficient of sodium along the ambient-pressure and critical isobars. Symbols show the DP-r2r^{2}SCAN results, and solid curves are analytic approximations. The Sobolev normal-pressure correlation [5] and the Fink–Leibowitz saturated-liquid recommendation [6] are shown for comparison.

The Fink–Leibowitz dependence [6] for saturated liquid sodium is also shown in Figure 11. It agrees with the present results below TbT_{b}, where the differences between the ambient-pressure, critical-isobar, and saturation curves are small. At higher temperatures, the uncertainty of the Fink–Leibowitz recommendation increases considerably.

The corresponding isentropic and isothermal bulk moduli are shown in Figure 12 and Figure 13. Both quantities decrease continuously with temperature, indicating mechanical softening of the liquid. At low temperatures, the atmospheric-pressure and critical-isobar results closely follow the Sobolev normal-pressure dependence. Along the atmospheric-pressure isobar, KSK_{S} and KTK_{T} decrease from 5.595.59 and 4.87 GPa4.87\ \mathrm{GPa} at 0.507 kK0.507\ \mathrm{kK} to

Figure 12. Isentropic bulk modulus KSK_{S} of sodium along the ambient-pressure and critical isobars. Symbols show the DP-r2r^{2}SCAN results, and the solid curves are analytic approximations. Black symbols are values obtained from the Fink–Leibowitz saturated-liquid compressibility [6], and the magenta curve is the Sobolev normal-pressure dependence [5]. The inset shows the low-temperature region on a linear ordinate scale.

Figure 13. Isothermal bulk modulus KTK_T of sodium along the atmospheric-pressure and critical isobars. Symbols show the DP-r2r^2SCAN results, and the solid curves are analytic approximations. Black symbols are values obtained from the Fink–Leibowitz saturated-liquid compressibility [6], and the magenta curve is the Sobolev normal-pressure dependence [5]. The inset shows the low-temperature region on a linear ordinate scale.

3.233.23 and 2.30 GPa2.30\ \mathrm{GPa} at TbT_{b}, respectively. Along the critical isobar, the corresponding values decrease from 5.615.61 and 4.88 GPa4.88\ \mathrm{GPa} at approximately 0.53 kK0.53\ \mathrm{kK} to 0.1370.137 and 0.023 GPa0.023\ \mathrm{GPa} at 2.493 kK2.493\ \mathrm{kK}, respectively. The Fink–Leibowitz values shown in Figure 12 and Figure 13 are obtained from the recommended saturated-liquid compressibilities. They are consistent with the present results at low temperatures, whereas their uncertainties increase strongly in the high-temperature region.

The Grüneisen parameter is calculated directly from the pressure–energy dependence along the isochrores (see Eq. (8), Figure 14 and Figure 15). The P(E)P(E) curves at V=constV=\mathrm{const} are shown in Figure 14.

Pressure–energy isochores calculated with DP-r²SCAN

Figure 14. Pressure–energy isochores calculated with DP-r2r^2SCAN. Legend entries give the density in g/cm3^3.

Figure 15. Grüneisen parameter of sodium along the ambient-pressure and critical isobars. Symbols are calculated from the pressure–energy isochores, and solid lines connect the calculated values. The magenta curve is recalculated from the Sobolev normal-pressure thermophysical correlations [5]; the shaded region indicates its estimated uncertainty.

As shown in Figure 15, the Grüneisen parameter decreases monotonically with temperature. The normal-pressure and critical-isobar results remain very close throughout the equilibrium normal-pressure liquid range up to TbT_{b}. Along the normal-pressure isobar, γ\gamma decreases from approximately 1.171.17 at 0.507 kK0.507\ \mathrm{kK} to 1.1031.103 at TbT_{b}. Along the critical isobar, it decreases from approximately 1.161.16 at 0.528 kK0.528\ \mathrm{kK} to about 0.30.3 in the vicinity of TcT_{c}. For comparison, Figure 15 also shows γ\gamma recalculated from the Sobolev normal-pressure thermophysical correlations using the same thermodynamic relation between γ\gamma, αP\alpha_{P}, CPC_{P}, and the sound velocity. This reconstructed dependence agrees with the present results in the low-temperature range.

Using the density, CPC_{P}, αP\alpha_{P}, and γ\gamma dependences obtained above, the adiabatic speed of sound is calculated from Eq. (18). Figure 16 shows that the sound velocity decreases with temperature, following the progressive mechanical softening seen in the bulk moduli. Along the atmospheric-pressure isobar, the sound velocity decreases from approximately 2.5 km/s at 0.5 kK to 2.1 km/s at TbT_b. Along the critical isobar, the sound velocity continues to decrease and reaches approximately 0.60 km/s near the critical point.

Figure 16. Adiabatic speed of sound along the normal-pressure and critical isobars. Blue and red circles denote values calculated from the thermodynamic functions along the normal-pressure and critical isobars, respectively, and filled diamonds denote direct acoustic simulations. The magenta curve is the Fink–Leibowitz recommended dependence [6].

The direct acoustic calculations provide an independent validation of the thermodynamic reconstruction. At

0.5 and 0.94 kK, the direct calculations give 2500(60) and 2200(100) m/s, respectively, in agreement with the thermodynamic values within their uncertainties. At lower temperatures, the calculated dependence also closely reproduces the Fink–Leibowitz recommendation [6].

Phase boundaries and surface tension

The melting temperature is determined using the two-phase NVTNVT simulations described in Sec. IIF. The calculations cover the density range ρ=0.93\rho= 0.93–0.98 g/cm30.98\ \mathrm{g/cm^3}. For each density, the interface velocity changes sign within the selected temperature interval. Linear interpolation to vint=0v_{\mathrm{int}} = 0 yields six points on the melting curve in the pressure range from −1.65-1.65 to 2.09 kbar2.09\ \mathrm{kbar}. These points are approximated by

Pm(Tm)=M1Tm+M0.(39)P_{\mathrm{m}}(T_{\mathrm{m}}) = M_1T_{\mathrm{m}} + M_0. \tag*{(39)}

Here TmT_{\mathrm{m}} is in K and PmP_{\mathrm{m}} is in kbar. The coefficients are M1=0.099 kbar/KM_1 = 0.099\ \mathrm{kbar/K} and M0=−34.2 kbarM_0 = -34.2\ \mathrm{kbar}. Interpolation of this dependence to atmospheric pressure with the bootstrap procedure gives

Tm,0=346(2) K.(40)T_{\mathrm{m},0} = 346(2)\ \mathrm{K}. \tag*{(40)}

The slope of the approximation is in agreement with the experimental value 0.11 kbar/K0.11\ \mathrm{kbar/K} [7, 90]. The calculated normal-pressure melting temperature is 25 K, or 6.7%, below the recommended value 370.93(6) K [8]. Menon et al. [91] show that a free-energy difference of 1 meV/atom may shift a transition temperature by up to about 50 K. In Ref. [92], electronic free-energy corrections of 4.2–5.8 meV/atom change the melting temperature by 48–57 K. The free-energy RMSE of the DP-r2r^2SCAN model is 3.5 meV/atom. Thus, within the accuracy of the model, the calculated melting temperature agrees well with experiment.

The coexistence densities obtained from the slab profiles using (23) are shown in Figure 7. The same two-phase simulations are used to calculate the surface tension from (24); the resulting temperature dependence is shown in Figure 17. The calculated surface tension decreases from 177.8 mN/m at 0.5 kK to 135.5 mN/m at 0.93 kK. At the same temperatures, the Sobolev recommendation gives 183.0 and 141.3 mN/m, respectively [5, 12, 13]. At higher temperatures, the surface tension decreases further to 61.9 mN/m at 1.703 kK and 1.02 mN/m at 2.480 kK, approaching zero as the critical point is reached. Over the entire temperature range, the calculated dependence closely follows the recommended Fink–Leibowitz and Sobolev correlations and remains consistent with their uncertainties.

Figure 17. Surface tension of sodium along the liquid–vapor coexistence curve. Red symbols denote the present DP-r2r^2SCAN results, and the red curve is the analytic approximation. The black and magenta curves show the Fink–Leibowitz and Sobolev recommended dependences, respectively [5, 6]. The inset shows the low-temperature region on a linear ordinate scale.

Transport properties of liquid sodium

The simulation trajectories were analyzed to obtain the self-diffusion coefficients along the isochores, and the resulting data were then fitted to evaluate the diffusion coefficient along the critical isobar. Figure 18 compares the present DP-r2r^2SCAN self-diffusion coefficients of liquid sodium along the critical isobar with available experimental and computational literature data. Along the critical isobar, the self-diffusion coefficient increases from

Temperature dependence of the self-diffusion coefficient of liquid sodium

Figure 18. Temperature dependence of the self-diffusion coefficient of liquid sodium. Red stars with error bars denote the present DP-r2SCANr^{2}\mathrm{SCAN} results along the critical isobar, P=PcP=P_{\mathrm{c}}, and the solid red line is the corresponding fit. The dashed black line is the constant-pressure Arrhenius correlation obtained by Ozelton and Swalin from their measurements combined with the earlier data of Meyer and Nachtrieb [93, 95]; open circles show the constant-volume measurements of Ozelton and Swalin [95]. The magenta curve shows the correlation of Larsson et al. [96]. The gray dash-dotted curve denotes the ab initio molecular-dynamics (AIMD) correlation of Qian et al. [24]. Open gray triangles, open black squares, and open magenta diamonds indicate the literature data of Gläser and Morkel [97], Pilgrim and Morkel [98], and Blagoveshchenskii et al. [99], respectively. The constant-pressure Ozelton–Swalin curve and the Larsson curve are reconstructed from the published Arrhenius-type expressions, while the Qian line is reconstructed from the activation-energy relation given in their paper. The inset enlarges the low-temperature region.

0.351 Ų/ps at 380 K to 0.726 Ų/ps at 500 K and then to about 30 Ų/ps in the critical region. At low temperatures, the present results agree well with the available experimental measurements. Somewhat higher values are given by the Meyer–Nachtrieb dependence [93], which exceeds the two lowest-temperature DP-r2r^2SCAN values by approximately 20–24%, and by the quasielastic-neutron result of Morkel and Pilgrim, 0.423 Ų/ps at 380 K [94].

For comparison, Figure 18 includes the constant-volume experimental data of Ozelton and Swalin [95] and their constant-pressure Arrhenius correlation obtained by combining their measurements with the earlier data of Meyer and Nachtrieb [93, 95], the tracer-diffusion correlation of Larsson et al. [96], the quasielastic-neutron-scattering data of Gläser and Morkel [97], the high-temperature neutron-scattering results of Pilgrim and Morkel [98], and the measurements of Blagoveshchenskii et al. [99]. In addition, the gray dash-dotted line shows the QMD correlation of Qian et al. [24]. The Pilgrim–Morkel value at 1773 K is obtained by refitting the published quasielastic spectrum. Overall, the present DP-r2r^2SCAN results reproduce the available low-temperature experimental data well and follow the known experimental and first-principles trends over the broader temperature range, while extending the available diffusion data into the expanded-liquid and near-critical regions, where direct experimental information is sparse.

The shear viscosity calculated along the critical isobar is shown in Figure 19. It decreases from 0.653 mPa s at 0.38 kK to 0.06 mPa s at 2.5 kK. The strongest decrease occurs in the low-temperature liquid region: the viscos-

Shear viscosity of sodium along the critical isobar

Figure 19. Shear viscosity of sodium along the critical isobar. Red stars show the DP-r2SCANr^{2}\mathrm{SCAN} results, and the solid red curve connects the calculated values. The green dashed curve is the Shpil’rain correlation [100]. The black curve and gray band show the Fink–Leibowitz recommended dependence and its uncertainty [6]. The vertical dashed line marks the critical temperature TcT_{\mathrm{c}}.

Its viscosity falls rapidly below approximately 1 kK, whereas its temperature dependence becomes considerably weaker at higher temperatures. Near the critical point, the viscosity remains finite and reaches values of about 0.06 mPa s.

The calculated values are compared with the Shpil’rain [100] and the Fink–Leibowitz [6] recommended dependences. Over most of the temperature range, the DP-r2SCANr^{2}\mathrm{SCAN} results closely follow both literature dependences, although the calculated viscosity is slightly lower. The literature correlations correspond to saturated-liquid conditions and are therefore used as reference dependences rather than as a direct comparison with the critical isobar.

Conclusions

In this work, we construct temperature-dependent PBE, AM05, and r2SCANr^{2}\mathrm{SCAN} deep potentials for sodium from finite-temperature DFT data and use them to investigate the thermophysical properties from the vicinity of melting to the critical region. The comparison of the three exchange-correlation functionals shows a strong functional dependence of the predicted critical temperature. DP-PBE and DP-AM05 give Tc=2.197(4)T_{\mathrm{c}}=2.197(4) and 2.183(3) kK, respectively, about 12% below the recommended value, whereas DP-r2SCANr^{2}\mathrm{SCAN} gives Tc=2.508(8)T_{\mathrm{c}}=2.508(8) kK, ρc=0.203(4)\rho_{\mathrm{c}}=0.203(4) g/cm3^{3}, and Pc=0.249(6)P_{\mathrm{c}}=0.249(6) kbar, in close agreement with the recommended critical parameters. The DP-r2SCANr^{2}\mathrm{SCAN} model also reproduces the normal bcc density within 0.06% of the value obtained from the experimental lattice parameter. A separate electronic-entropy model is used to recover the internal energy required for the caloric properties.

Using the DP-r2SCANr^{2}\mathrm{SCAN} equation of state, we reconstruct the normal-pressure and critical isobars and obtain a consistent set of thermodynamic properties, including the enthalpy, CPC_{P}, CVC_{V}, thermal expansion coefficient, isothermal and isentropic bulk moduli, Grünesien parameter, and speed of sound. At low and intermediate temperatures, the calculated normal-pressure properties generally follow the available experimental data and recommended correlations. Along the critical isobar, on approaching the critical region, the thermal expansion and heat capacities increase, the bulk moduli decrease strongly, and the Grünesien parameter and speed of sound decrease. The speed of sound obtained from the thermodynamic functions is independently confirmed by direct acoustic simulations, providing a consistency check for the reconstructed EOS and its derivatives.

The phase-boundary calculations provide complementary tests of the potential. Direct solid–liquid coexistence simulations yield a local melting curve between −1.65 and 2.09 kbar with a slope of 0.099 kbar/K, close to the experimental value of 0.11 kbar/K. Its interpolation to ambient pressure gives 346(2) K, approximately 25 K below the recommended value. The magnitude of this deviation is consistent with the sensitivity of phase-transition temperatures to free-energy errors on the meV/atom scale. The calculated liquid–vapor coexistence densities reproduce the overall shape of the sodium binodal and approach the independently determined critical point. The surface tension agrees closely with the recommended dependences over the available temperature range, decreasing from 177.8 mN/m at 0.5 kK to 1.02 mN/m at 2.48 kK and approaching zero near TcT_{\mathrm{c}}.

The calculated transport properties extend the available information into the expanded-liquid and near-critical regions. Along the critical isobar, the self-diffusion coefficient increases strongly with temperature. The calculated values agree well with the available low-temperature experimental measurements and follow the known experimental and first-principles trends over the broader temperature range, while extending the available diffusion data into the near-critical region. The shear viscosity decreases from 0.653 mPa s at 0.38 kK to 0.06 mPa s near the critical point and remains close to the available reference dependences over most of the temperature range.

Thus, we demonstrate for the first time that a single DP-r2r^{2}SCAN neural-network interatomic potential can provide a unified description of sodium, simultaneously reproducing equilibrium thermodynamics, phase boundaries, interfacial and acoustic properties, and transport phenomena over an exceptionally broad thermodynamic range, from room temperature to the near-critical and supercritical regimes. The near-experimental agreement achieved across this diverse set of properties demonstrates an unprecedented level of transferability and predictive consistency for an atomistic model of sodium.

Acknowledgments

We thank Nikolay Chtchelkatchev for valuable discussions. The authors acknowledge the JIHT RAS Supercomputer Centre and the Shared Resource Centre “Far Eastern Computing Resource” IACP FEB RAS for providing computing time.

References

to include surface effects in self-consistent density functional theory, Phys. Rev. B 72, 085108 (2005).

[54] J. W. Furness, A. D. Kaplan, J. Ning, J. P. Perdew, and J. Sun, Accurate and numerically efficient r²SCAN meta-generalized gradient approximation, J. Phys. Chem. Lett. 11, 8208 (2020).

[55] J. Sun, A. Ruzsinszky, and J. P. Perdew, Strongly constrained and appropriately normed semilocal density functional, Phys. Rev. Lett. 115, 036402 (2015).

[56] P. Kovacs, F. Tran, P. Blaha, and G. K. H. Madsen, Comparative study of the PBE and SCAN functionals: The particular case of alkali metals, J. Chem. Phys. 150, 164119 (2019).

[57] A. Baldereschi, Mean-Value Point in the Brillouin Zone, Phys. Rev. B 7, 5212 (1973).

[58] A. P. Thompson, H. M. Aktulga, R. Berger, D. S. Bolintineanu, W. M. Brown, P. S. Crozier, P. J. in ’t Veld, A. Kohlmeyer, S. G. Moore, T. D. Nguyen, R. Shan, M. J. Stevens, J. Tranchida, C. Trott, and S. J. Plimpton, LAMMPS–a flexible simulation tool for particle-based materials modeling at the atomic, meso, and continuum scales, Computer Physics Communications 271, 108171 (2022).

[59] S. Nosé, A unified formulation of the constant temperature molecular dynamics methods, J. Chem. Phys. 81, 511 (1984).

[60] M. A. Paramonov, D. V. Minakov, A. V. Dorovatovsky, M. A. Sheindlin, V. B. Fokin, G. S. Demyanov, and P. R. Levashov, High-temperature thermophysical properties of liquid zirconium: Quantum molecular dynamics and pulse heating experiment, Phys. Rev. B 110, 184204 (2024).

[61] I. V. Lomonosov, Equations of state of metals in wdm region, AIP Conference Proceedings 1793, 050022 (2017).

[62] A. B. Medvedev and R. F. Trunin, Shock compression of porous metals and silicates, Physics-Uspekhi 55, 773 (2012).

[63] Y. Asano, H. Watanabe, and H. Noguchi, Molecular dynamics simulation of soundwave propagation in a simple fluid, J. Chem. Phys. 153, 124504 (2020).

[64] D. Y. Sun, M. Asta, and J. J. Hoyt, Kinetic coefficient of ni solid-liquid interfaces from molecular-dynamics simulations, Phys. Rev. B 69, 024108 (2004).

[65] S. W. Sides, G. S. Grest, and M.-D. Lacasse, Capillary waves at liquid-vapor interfaces: A molecular-dynamics simulation, Phys. Rev. E 60, 6708 (1999).

[66] B. A. Bauer and S. Patel, Properties of water along the liquid–vapor coexistence curve via molecular dynamics simulations using the polarizable TIP4P-QDP-LJ water model, J. Chem. Phys. 131, 084709 (2009).

[67] J. G. Kirkwood and F. P. Buff, The statistical mechanical theory of surface tension, J. Chem. Phys. 17, 338 (1949).

[68] C. S. Barrett, X-ray study of the alkali metals at low temperatures, Acta Crystallographica 9, 671 (1956).

[69] M. Hanfland, I. Loa, and K. Syassen, Sodium under pressure: bcc to fcc structural transition and pressure-volume relation to 100 GPa, Phys. Rev. B 65, 184109 (2002).

[70] Supplemental material (2026), complete equation-of-state data and additional details.

[71] G. R. Gathers, Dynamic methods for investigating thermophysical properties of matter at very high temperatures and pressures, Reports on Progress in Physics 49, 341 (1986).

[72] V. E. Fortov, A. N. Dremin, and A. A. Leont’ev, Evaluation of the parameters of the critical point, High Temperature 13, 984 (1975).

[73] D. A. Young and B. J. Alder, Critical point of metals from the van der waals model, Phys. Rev. A 3, 364 (1971).

[74] F. Petiot and J. M. Seiler, Physical properties of sodium: A contribution to the estimation of critical coordinates, High Temperatures—High Pressures 16, 289 (1984).

[75] K. Hornung, Liquid metal coexistence properties from corresponding states and third law, J. Appl. Phys. 46, 2548 (1975).

[76] I. V. Lomonosov, Fazovye diagrammy i termodinamicheskie svoistva metallov pri vysokikh davleniyakh i temperaturakh, Doctoral dissertation, Institute of Problems of Chemical Physics, Russian Academy of Sciences, Chernogolovka (2000), 178 pp.; specialty 01.04.14; in Russian.

[77] P. R. Levashov, Uravneniya sostoyaniya zhidkoi fazy metallov pri vysokikh davleniyakh i temperaturakh (2000), candidate of Physical and Mathematical Sciences dissertation, specialty 01.04.14, Moscow; in Russian.

[78] E. Morris, An Application of the Theory of Corresponding States to the Prediction of the Critical Constants of Metals, Tech. Rep. AWRE-O-67/64 (Atomic Weapons Research Establishment, United Kingdom Atomic Energy Authority, United Kingdom, 1964).

[79] N. B. Vargaftik, Tables on the Thermophysical Properties of Liquids and Gases in Normal and Dissociated States, 2nd ed. (Hemisphere Publishing Corporation, Washington, DC, 1975) distributed by Halsted Press.

[80] K. Thurnay, Thermophysical Properties of Sodium in the Liquid and Gaseous States, Tech. Rep. KfK 2863 (Kernforschungszentrum Karlsruhe GmbH, Karlsruhe, 1981).

[81] R. W. Ohse, J.-F. Babelot, J. Magill, and M. Tetenbaum, An assessment of the melting, boiling, and critical point data of the alkali metals, Pure and Applied Chemistry 57, 1407 (1985).

[82] J. F. Barnes, An equation of state for sodium over an extended temperature and density range, in Thermodynamics of Nuclear Materials 1974 (International Atomic Energy Agency, Vienna, 1975) iAEA-SM-190/45.

[83] A. G. Mozgovoi, L. R. Fokin, and A. I. Chernov, Critical parameters of alkali metals, Review on Thermophysical Properties of Substances, 3 (1984), in Russian.

[84] N. B. Vargaftik, V. A. Alekseev, V. F. Kozhevnikov, Y. F. Ryzhkov, and V. G. Stepanov, Equation of state of the liquid alkali metals, Journal of Engineering Physics 35, 1361 (1978).

[85] P. I. Bystrov, D. N. Kagan, G. A. Krechetova, and E. E. Shpil’rain, Liquid-Metal Coolants for Heat Pipes and Power Plants, edited by V. A. Kirillin (Hemisphere Publishing Corporation, New York, 1990) p. 272.

[86] E. E. Shpil’rain, K. A. Yakimovich, V. A. Fomin, S. N. Skovorod’ko, and A. G. Mozgovoi, Density and thermal expansion of liquid alkali metals, in Handbook of Thermodynamic and Transport Properties of Alkali Metals, edited by R. W. Ohse (Blackwell Scientific Publications, Oxford, 1985) Chap. 6.3.3, pp. 435–469.

References

  1. [1]C. K. Matthews, Liquid sodium—the heat transport medium in fast breeder reactors, Bulletin of Materials Science 16, 477 (1993).DOI
  2. [2]Y. Sakamoto, J.-C. Garnier, J. Rouault, C. Grandy, T. Fanning, R. Hill, Y. Chikazawa, and S. Kotake, Selection of sodium coolant for fast reactors in the US, France and Japan, Nuclear Engineering and Design 254, 194 (2013).DOI
  3. [3]H. Li, X. Zhang, Y. Sun, and M. Li, Thermodynamic properties of liquid sodium under high pressure, AIP Advances 7, 045305 (2017).
  4. [4]Z. Liu, X. Li, T. Cong, R. Zhang, L. Zheng, H. Deng, and Y. Cui, Uncertainties analysis on the prediction of flow and heat transfer of liquid sodium with CFD technology, Science and Technology of Nuclear Installations 2020, 4239143 (2020).DOI
  5. [5]V. Sobolev, Database of Thermophysical Properties of Liquid Metal Coolants for GEN-IV: Sodium, Lead, Lead–Bismuth Eutectic (and Bismuth), SCK CEN Scientific Report BLG-1069 (SCK CEN, Mol, Belgium, 2011) original report November 2010; revised December 2011.
  6. [6]J. K. Fink and L. Leibowitz, Thermodynamic and Transport Properties of Sodium Liquid and Vapor, Tech. Rep. ANL/RE-95/2 (Argonne National Laboratory, Argonne, IL, 1995).DOI
  7. [7]L. V. Gurvich, I. V. Veitz, V. A. Medvedev, et al., Thermodynamic Properties of Individual Substances, 3rd ed., edited by V. P. Glushko, Vol. 4 (Nauka, Moscow, 1982) books 1 and 2; in Russian.
  8. [8]N. Narayana and D. R. Burgess, Jr., Melting Points and Boiling Points for the Alkali Metals, NIST Technical Note NIST TN 2273 (National Institute of Standards and Technology, Gaithersburg, MD, 2024).
  9. [9]D. C. Ginnings, T. B. Douglas, and A. F. Ball, Heat capacity of sodium between 0 and 900 degrees c, the triple point and heat of fusion, Journal of Research of the National Bureau of Standards 45, 23 (1950).
  10. [10]D. R. Fredrickson and M. G. Chasanov, The enthalpy of liquid sodium to 1505 k by drop calorimetry, The Journal of Chemical Thermodynamics 6, 629 (1974).DOI
  11. [11]G. H. Shaw and D. A. Caldwell, Sound-wave velocities in liquid alkali metals studied at temperatures up to 150° c and pressures up to 0.7 gpa, Phys. Rev. B 32, 7937 (1985).
  12. [12]F. E. Poindexter and M. Kernaghan, Surface tension of sodium, Phys. Rev. 33, 837 (1929).
  13. [13]A. A. Kiriyanenko, O. P. Makarova, V. D. Romanov, and A. N. Solov’ev, Experimental investigation of the surface tension of liquid sodium, Journal of Applied Mechanics and Technical Physics 6, 121 (1965).
  14. [14]N. D. Mermin, Thermal properties of the inhomogeneous electron gas, Phys. Rev. 137, A1441 (1965).
  15. [15]G. Kresse and J. Hafner, Ab initio molecular dynamics for liquid metals, Phys. Rev. B 47, 558 (1993).
  16. [16]G. Kresse and J. Furthmüller, Efficient iterative schemes for ab initio total-energy calculations using a plane-wave basis set, Phys. Rev. B 54, 11169 (1996).
  17. [17]A. K. Metya, A. Hens, and J. K. Singh, Molecular dynamics study of vapor–liquid equilibria and transport properties of sodium and lithium based on EAM potentials, Fluid Phase Equilibria 313, 16 (2012).
  18. [18]D. V. Minakov, M. A. Paramonov, and P. R. Levashov, Ab initio inspection of thermophysical experiments for [19] D. V. Minakov, M. A. Paramonov, and P. R. Levashov, Thermophysical properties of liquid molybdenum in the near-critical region using quantum molecular dynamics, Phys. Rev. B 103, 184204 (2021).
  19. [20]M. A. Paramonov, D. V. Minakov, V. B. Fokin, D. V. Knyazev, G. S. Demyanov, and P. R. Levashov, Ab initio inspection of thermophysical experiments for zirconium near melting, J. Appl. Phys. 132, 065102 (2022).DOI
  20. [21]D. V. Minakov, M. A. Paramonov, and P. R. Levashov, Consistent interpretation of experimental data for expanded liquid tungsten near the liquid-gas coexistence curve, Phys. Rev. B 97, 024205 (2018).
  21. [22]D. V. Minakov, M. A. Paramonov, G. S. Demyanov, V. B. Fokin, and P. R. Levashov, Ab initio calculation of hafnium and zirconium melting curves via the Lindemann criterion, Phys. Rev. B 106, 214105 (2022).DOI
  22. [23]M. A. Paramonov, D. V. Minakov, I. S. Galtsov, and P. R. Levashov, Ab initio equation of state, critical point, and ionic transport properties of liquid expanded lead, Phys. Rev. B 114, 074203 (2026).
  23. [24]G. X. Qian, M. Weinert, G. W. Fernando, and J. W. Davenport, First-principles calculation of the activation energy for diffusion in liquid sodium, Phys. Rev. Lett. 64, 1146 (1990).
  24. [25]S. R. Bickham, O. Pfaffenzeller, L. A. Collins, J. D. Kress, and D. Hohl, Ab initio molecular dynamics of expanded liquid sodium, Phys. Rev. B 58, R11813 (1998).
  25. [26]D. J. Gonzalez, L. E. Gonzalez, and M. J. Stott, Surface structure of liquid Li and Na: An ab initio molecular dynamics study, Phys. Rev. Lett. 92, 085501 (2004).
  26. [27]E. R. Hernández and J. Íñiguez, First-principles simulations on the nature of the melting line of sodium, Phys. Rev. Lett. 98, 055501 (2007).
  27. [28]L. Koči, R. Ahuja, L. Vitos, and U. Pinskook, Melting of Na at high pressure from ab initio calculations, Phys. Rev. B 77, 132101 (2008).
  28. [29]H. Eshet, R. Z. Khaliullin, T. D. Kühne, J. Behler, and M. Parrinello, Ab initio quality neural-network potential for sodium, Phys. Rev. B 81, 184107 (2010).
  29. [30]H. Eshet, R. Z. Khaliullin, T. D. Kühne, J. Behler, and M. Parrinello, Microscopic origins of the anomalous melting behavior of sodium under high pressure, Phys. Rev. Lett. 108, 115701 (2012).
  30. [31]A. Irie, S. Fukushima, A. Koura, K. Shimamura, and F. Shimojo, Reproduction of melting and crystallization of sodium by machine-learning interatomic potential based on artificial neural networks, Journal of the Physical Society of Japan 90, 094603 (2021).
  31. [32]M. Pozzo, M. P. Desjarlais, and D. Alfè, Electrical and thermal conductivity of liquid sodium from first-principles calculations, Phys. Rev. B 84, 054203 (2011).
  32. [33]Z. Li, C. Windisoerffer, F. Soubiran, and R. Caracas, Ab initio Gibbs ensemble Monte Carlo simulations of the liquid–vapor equilibrium and the critical point of sodium, Physical Chemistry Chemical Physics 23, 311 (2021).DOI
  33. [34]Y. Liu, H. Liu, and J. S. Tse, Electronic origin of the anomalous melting of sodium under pressure, Proceedings of the National Academy of Sciences of the United States of America 122, e250213122 (2025).
  34. [35]E. A. Vazquez, J. L. Alvarez, and M. L. Japas, Liquid–vapor coexistence curve and critical point of sodium, revisited, Fluid Phase Equilibria 443, 14 (2017).DOI
  35. [36]J. L. Alvarez and M. L. Japas, Enthalpies and susceptibilities of coexisting vapor and liquid sodium at high temperatures, Journal of Molecular Liquids 295, 111711 (2019).DOI
  36. [37]E. V. Usov, Extrapolation of liquid sodium properties to the region of high temperatures and overheating, High Temperature 61, 604 (2023).
  37. [38]S. Kumar, H. Tahmashi, K. Ramakrishna, M. Lokamani, S. Nikolov, J. Tranchida, M. A. Wood, and A. Cangi, Transferable interatomic potential for aluminum from ambient conditions to warm dense matter, Phys. Rev. Research 5, 033162 (2023).
  38. [39]Y. Kataoka, J. Haruyama, O. Sugino, and M. Shiga, Predictive evaluation of hydrogen diffusion coefficient on Pd(111) surface by path integral simulations using neural network potential, Phys. Rev. Research 6, 043224 (2024).
  39. [40]C. Luo, Y. Sun, and R. M. Wentzovitch, Probing the state of hydrogen in δ-AlOOH at mantle conditions with machine learning potential, Phys. Rev. Research 6, 013292 (2024).
  40. [41]Y. Zhang, C. Gao, Q. Liu, L. Zhang, H. Wang, and M. Chen, Warm dense matter simulation via electron temperature dependent Deep Potential molecular dynamics, Physics of Plasmas 27, 122704 (2020).
  41. [42]C. Ben Mahmoud, F. Grasselli, and M. Ceriotti, Predicting hot-electron free energies from ground-state data, Phys. Rev. B 106, L121116 (2022).
  42. [43]P. Srinivasan, D. Demuriya, B. Grabowski, and A. Shapeev, Electronic moment tensor potentials include both electronic and vibrational degrees of freedom, npj Computational Materials 10, 41 (2024).
  43. [44]X. Long and K. Luo, Location of the liquid-vapor critical point in aluminum, Phys. Rev. B 113, 174106 (2026).
  44. [45]L. Zhang, J. Han, H. Wang, R. Car, and W. E, Deep potential molecular dynamics: A scalable model with the accuracy of quantum mechanics, Phys. Rev. Lett. 120, 143001 (2018).
  45. [46]H. Wang, L. Zhang, J. Han, and W. E, Deepmd-kit: A deep learning package for many-body potential energy representation and molecular dynamics, Computer Physics Communications 228, 178 (2018).
  46. [47]G. Kresse and J. Hafner, Ab initio molecular-dynamics simulation of the liquid-metal–amorphous-semiconductor transition in germanium, Phys. Rev. B 49, 14251 (1994).
  47. [48]G. Kresse and J. Furthmüller, Efficiency of ab-initio total energy calculations for metals and semiconductors using a plane-wave basis set, Computational Materials Science 6, 15 (1996).
  48. [49]P. E. Blöchl, Projector augmented-wave method, Phys. Rev. B 50, 17953 (1994).
  49. [50]G. Kresse and D. Joubert, From ultrasoft pseudopotentials to the projector augmented-wave method, Phys. Rev. B 59, 1758 (1999).
  50. [51]J. P. Perdew, K. Burke, and M. Ernzerhof, Generalized Gradient Approximation Made Simple, Phys. Rev. Lett. 77, 3865 (1996).
  51. [52]J. P. Perdew, K. Burke, and M. Ernzerhof, Generalized Gradient Approximation Made Simple [Phys. Rev. Lett. 77, 3865 (1996)], Phys. Rev. Lett. 78, 1396 (1997).
  52. [53]R. Armiento and A. E. Mattsson, Functional designed to include surface effects in self-consistent density functional theory, Phys. Rev. B 72, 085108 (2005).
  53. [54]J. W. Furness, A. D. Kaplan, J. Ning, J. P. Perdew, and J. Sun, Accurate and numerically efficient r²SCAN meta-generalized gradient approximation, J. Phys. Chem. Lett. 11, 8208 (2020).
  54. [55]J. Sun, A. Ruzsinszky, and J. P. Perdew, Strongly constrained and appropriately normed semilocal density functional, Phys. Rev. Lett. 115, 036402 (2015).
  55. [56]P. Kovacs, F. Tran, P. Blaha, and G. K. H. Madsen, Comparative study of the PBE and SCAN functionals: The particular case of alkali metals, J. Chem. Phys. 150, 164119 (2019).
  56. [57]A. Baldereschi, Mean-Value Point in the Brillouin Zone, Phys. Rev. B 7, 5212 (1973).
  57. [58]A. P. Thompson, H. M. Aktulga, R. Berger, D. S. Bolintineanu, W. M. Brown, P. S. Crozier, P. J. in ’t Veld, A. Kohlmeyer, S. G. Moore, T. D. Nguyen, R. Shan, M. J. Stevens, J. Tranchida, C. Trott, and S. J. Plimpton, LAMMPS–a flexible simulation tool for particle-based materials modeling at the atomic, meso, and continuum scales, Computer Physics Communications 271, 108171 (2022).
  58. [59]S. Nosé, A unified formulation of the constant temperature molecular dynamics methods, J. Chem. Phys. 81, 511 (1984).
  59. [60]M. A. Paramonov, D. V. Minakov, A. V. Dorovatovsky, M. A. Sheindlin, V. B. Fokin, G. S. Demyanov, and P. R. Levashov, High-temperature thermophysical properties of liquid zirconium: Quantum molecular dynamics and pulse heating experiment, Phys. Rev. B 110, 184204 (2024).
  60. [61]I. V. Lomonosov, Equations of state of metals in wdm region, AIP Conference Proceedings 1793, 050022 (2017).
  61. [62]A. B. Medvedev and R. F. Trunin, Shock compression of porous metals and silicates, Physics-Uspekhi 55, 773 (2012).
  62. [63]Y. Asano, H. Watanabe, and H. Noguchi, Molecular dynamics simulation of soundwave propagation in a simple fluid, J. Chem. Phys. 153, 124504 (2020).
  63. [64]D. Y. Sun, M. Asta, and J. J. Hoyt, Kinetic coefficient of ni solid-liquid interfaces from molecular-dynamics simulations, Phys. Rev. B 69, 024108 (2004).
  64. [65]S. W. Sides, G. S. Grest, and M.-D. Lacasse, Capillary waves at liquid-vapor interfaces: A molecular-dynamics simulation, Phys. Rev. E 60, 6708 (1999).
  65. [66]B. A. Bauer and S. Patel, Properties of water along the liquid–vapor coexistence curve via molecular dynamics simulations using the polarizable TIP4P-QDP-LJ water model, J. Chem. Phys. 131, 084709 (2009).
  66. [67]J. G. Kirkwood and F. P. Buff, The statistical mechanical theory of surface tension, J. Chem. Phys. 17, 338 (1949).
  67. [68]C. S. Barrett, X-ray study of the alkali metals at low temperatures, Acta Crystallographica 9, 671 (1956).
  68. [69]M. Hanfland, I. Loa, and K. Syassen, Sodium under pressure: bcc to fcc structural transition and pressure-volume relation to 100 GPa, Phys. Rev. B 65, 184109 (2002).
  69. [70]Supplemental material (2026), complete equation-of-state data and additional details.
  70. [71]G. R. Gathers, Dynamic methods for investigating thermophysical properties of matter at very high temperatures and pressures, Reports on Progress in Physics 49, 341 (1986).
  71. [72]V. E. Fortov, A. N. Dremin, and A. A. Leont’ev, Evaluation of the parameters of the critical point, High Temperature 13, 984 (1975).
  72. [73]D. A. Young and B. J. Alder, Critical point of metals from the van der waals model, Phys. Rev. A 3, 364 (1971).
  73. [74]F. Petiot and J. M. Seiler, Physical properties of sodium: A contribution to the estimation of critical coordinates, High Temperatures–High Pressures 16, 289 (1984).
  74. [75]K. Hornung, Liquid metal coexistence properties from corresponding states and third law, J. Appl. Phys. 46, 2548 (1975).
  75. [76]I. V. Lomonosov, Fazovye diagrammy i termodinamicheskie svoistva metallov pri vysokikh davleniyakh i temperaturakh, Doctoral dissertation, Institute of Problems of Chemical Physics, Russian Academy of Sciences, Chernogolovka (2000), 178 pp.; specialty 01.04.14; in Russian.
  76. [77]P. R. Levashov, Uravneniya sostoyaniya zhidkoi fazy metallov pri vysokikh davleniyakh i temperaturakh (2000), candidate of Physical and Mathematical Sciences dissertation, specialty 01.04.14, Moscow; in Russian.
  77. [78]E. Morris, An Application of the Theory of Corresponding States to the Prediction of the Critical Constants of Metals, Tech. Rep. AWRE-O-67/64 (Atomic Weapons Research Establishment, United Kingdom Atomic Energy Authority, United Kingdom, 1964).
  78. [79]N. B. Vargaftik, Tables on the Thermophysical Properties of Liquids and Gases in Normal and Dissociated States, 2nd ed. (Hemisphere Publishing Corporation, Washington, DC, 1975) distributed by Halsted Press.
  79. [80]K. Thurnay, Thermophysical Properties of Sodium in the Liquid and Gaseous States, Tech. Rep. KfK 2863 (Kernforschungszentrum Karlsruhe GmbH, Karlsruhe, 1981).
  80. [81]R. W. Ohse, J.-F. Babelot, J. Magill, and M. Tetenbaum, An assessment of the melting, boiling, and critical point data of the alkali metals, Pure and Applied Chemistry 57, 1407 (1985).
  81. [82]J. F. Barnes, An equation of state for sodium over an extended temperature and density range, in Thermodynamics of Nuclear Materials 1974 (International Atomic Energy Agency, Vienna, 1975) iAEA-SM-190/45.
  82. [83]A. G. Mozgоvoi, L. R. Fokin, and A. I. Chernov, Critical parameters of alkali metals, Reviews on Thermophysical Properties of Substances, 3 (1984), in Russian.
  83. [84]N. B. Vargaftik, V. A. Alekseev, V. F. Kozhevnikov, Y. F. Ryzhkov, and V. G. Stepanov, Equation of state of the liquid alkali metals, Jоurnal of Engineering Physics 35, 1361 (1978).
  84. [85]P. I. Bystrov, D. N. Kagan, G. A. Krechetova, and E. E. Shpil’rain, Liquid-Metal Coolants for Heat Pipes and Power Plants, edited by V. A. Kirillin (Hemisphere Publishing Corporation, New York, 1990) p. 272.
  85. [86]E. E. Shpil’rain, K. A. Yаkimovich, V. A. Fomin, S. N. Skovorod’ko, and A. G. Mozgovoi, Density and thermal expansion of liquid alkali metals, in Handbook of Thermodynamic and Transport Properties of Alkali Metals, edited by R. W. Ohse (Blackwell Scientific Publications, Oxford, 1985) Chap. 6.3.3, pp. 435–469.
  86. [87]Y. S. Touloukian, R. K. Kirby, R. E. Taylor, and P. D. Desai, Thermal Expansion: Metallic Elements and Alloys, Thermophysical Properties of Matter: The TPRC Data Series, Vol. 12 (IFI/Plenum, New York, 1975).
  87. [88]M. W. Chase, Jr., NIST-JANAF Thermochemical Tables, 4th ed., Journal of Physical and Chemical Reference Data Monograph No. 9 (American Institute of Physics, New York, 1998) pp. 1–1951.
  88. [89]P. L. Kirillov, ed., Thermophysical Properties of Materials for Nuclear Engineering: A Tutorial and Collection of Data (International Atomic Energy Agency, Vienna, 2008) iAEA-THPH.
  89. [90]R. Boehler, Melting temperature, adiabats, and grü­neisen parameter of lithium, sodium and potassium versus pressure, Phys. Rev. B 27, 6754 (1983).
  90. [91]S. Menon, Y. Lysogorskiy, A. L. M. Knoll, N. Leimeroth, M. Poul, M. Qamar, J. Janssen, M. Mrovec, J. Rohrer, K. Albe, J. Behler, R. Drautz, and J. Neugebauer, From electrons to phase diagrams with machine learning potentials using pyiron based automated workflows, npj Computational Materials 10, 261 (2024).
  91. [92]L.-F. Zhu, F. Körmann, Q. Chen, M. Selleby, J. Neugebauer, and B. Grabowski, Accelerating ab initio melting property calculations with machine learning: application to the high entropy alloy tavcrw, npj Computational Materials 10, 274 (2024).
  92. [93]R. E. Meyer and N. H. Nachtrieb, Self-diffusion of liquid sodium, J. Chem. Phys. 23, 1851 (1955).
  93. [94]C. Morkel and W.-C. Pilgrim, Density dependent single particle motion in liquid sodium, Journal of Non-Crystalline Solids 312–314, 128 (2002).
  94. [95]M. W. Ozelton and R. A. Swalin, Self-diffusion in liquid sodium at constant volume and constant pressure, Philosophical Magazine 18, 441 (1968).
  95. [96]S. J. Larsson, C. Roxbergh, and A. Lodding, Self-diffusion in liquid alkali metals, Physics and Chemistry of Liquids 3, 137 (1972).
  96. [97]W. Gläser and C. Morkel, Self-diffusion in simple liquid metals, Journal of Non-Crystalline Solids 61–62, 309 (1984).
  97. [98]W.-C. Pilgrim and C. Morkel, Density dependence of the interrelation between single particle motion and the collective dynamics in liquid sodium, Zeitschrift für Physikalische Chemie 217, 957 (2003).
  98. [99]N. M. Blagoveshchenskii, A. G. Novikov, A. V. Puchkov, V. V. Savostin, M. Shamaev, and I. I. Zasorin, Investigation of diffusion processes in liquid sodium and sodium-hydrogen melt by quasielastic neutron scattering, JETP Letters 98, 834 (2013).
  99. [100]E. E. Shpil'rain, K. A. Yakimovich, V. A. Fomin, S. N. Skovorodjko, and A. G. Mozgိုးvoi, Dynamic and kinematic viscosity of liquid alkali metals, in Handbook of Thermodynamic and Transport Properties of Alkali Metals, edited by R. W. Ohse (Blackwell Scientific Publications, Boston, 1985) Chap. 7.3, pp. 753–784.

Paper details

vlnc:W_48dfxjd6
Version
v1 · latest
Published
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents