betaFeedback

WorksPhysics and Astronomy

Regulating nanoscale heat transfer with Janus nanoparticles

Abstract

Janus nanoparticles (JNPs) with heterogeneous compositions or interfacial properties can exhibit directional heating upon external excitation, such as laser radiation and magnetic field. This directional heating may be harnessed for new nanotechnology and biomedical applications. Understanding thermal transport and temperature control with JNP heating is critical for these advances. Here, we developed a numerical framework to analyze the asymmetric thermal transport in JNP heating under photothermal stimulation. We found that JNP-induced temperature contrast, defined as the ratio of temperature increase in the surrounding water, shows a substantial size and polar angle dependence. Notably, we discovered a significant enhancement of the temperature contrast under pulsed heating due to thermal confinement, compared with the continuous heating. This work brings new insights into the thermal responses of JNP heating and advances the field.

Main context:

Introduction

In the past decade, remarkable advances have been made with the development of nanoparticle heating,[1] [2, 3, 4] including cancer treatment,5-9 neuron modulation,10, 11 molecular hyperthermia,12-14 point-of-care diagnostic,15 imaging enhancement,16-18 energy harvesting,19, 20 and catalysis.21-23 Janus nanoparticles (JNPs) have recently brought new opportunities to the field.24, 25 JNPs are novel nanostructures consisting of heterogeneous structures and materials, including combinations of metallic and non-metallic materials.26-28 The asymmetric coating on JNPs can lead to heterogeneous interfacial properties, as an example, hydrophobic versus hydrophilic with high versus low interfacial thermal resistances (ITRs), respectively.29 This heterogeneity of interfacial properties can be used to regulate the thermal transport around the JNP and lead to directional heating.30, 31 The directional heating has enabled novel applications with JNPs, such as thermophoretic nanomotor,31-33 nano tweezer,34, 35 Janus nano pen injection,36 and energy management.37

The central issue for JNP heating is a better understanding of thermal transport.35 Olarte-Plata et al. analyzed the directional heating of JNPs with heterogeneous coating and ITRs using molecular dynamic simulation and demonstrated a temperature difference (~10K) with octanethiolate/mercaptohexanol-coated JNPs.30 Besides this modeling work, Xuan et al. have developed a self-driven thermophoretic nanomotor with continuous JNP heating. They have shown the speed of the nanomotor can reach ~40 μm/s40\,\mu\mathrm{m}/\mathrm{s} with a laser intensity of 60 W/cm260\,\mathrm{W}/\mathrm{cm}^{2}.33 While these studies have greatly advanced our understanding of directional heating with JNP and demonstrated promising applications, it remains unclear how heterogeneous interface properties of JNP and laser excitation (continuous vs pulsed) contribute to regulating the nanoscale thermal transport.

In this work, we developed a finite difference model to elucidate how the heterogeneous interface properties and laser excitation method regulate the nanoscale heat transfer (Figure 1A). we defined a dimensionless parameter based on the ratio of asymmetric temperature increase (ζ=ΔT1ΔT2\zeta= \frac{\Delta T_1}{\Delta T_2}, Figure 1B, where ΔT1\Delta T_1 and ΔT2\Delta T_2 indicates the representative temperature rise of the two coating parts.) to quantify the directional heating. Our results suggest that increasing JNP size reduces the temperature contrast. We found that the distribution of interface thermal resistance led to an asymmetric impact on the temperature contrast. Importantly, we demonstrate a significant enhancement of the temperature contrast with pulsed JNP heating compared with continuous heating. Our work advances the understanding of directional heating with JNP and brings new perspectives and potential applications to the field.

Schematic illustration of the modeling of JNP heating

Figure 1. Schematic illustration of the modeling of JNP heating. (A) A spherical Janus nanoparticle (JNP) is heterogeneously coated, leading to nonuniform interfacial thermal resistance (ITR). The two ITRs on the JNP are R1R_1, covering the north pole, and R2R_2, covering the south pole. The polar angle (θ0\theta_0) is defined as the critical cone angle that pinpoints the boundary between two ITRs. We impose continuous and pulsed heating on the JNP to model the steady-state and transient heating scenarios. (B) We developed an FDM numerical model and discretized the system under spherical coordinates. We defined the dimensionless parameter (ζ=ΔT1ΔT2\zeta= \frac{\Delta T_1}{\Delta T_2}) to characterize the directional heating.

Method

Theoretical model

We start with establishing the theoretical model. Here we consider a plasmonic JNP with a gold core, asymmetric coating on its surface, and thus heterogeneous ITR (Figure 1A) along the interface. The JNP is submerged in an aqueous solution, and heat can transport through the interface into the water when the JNP is excited by laser radiation.35

Recently, studies reported that heat conduction under the nanoscale could deviate from Fourier’s law when the mean free path is comparable to the characteristic length.38 In this work, the temperature profile in the water domain is our primary concern. Considering that the mean free path in the water (∼0.1nm\sim0.1\mathrm{nm}) is orders of magnitude smaller than the characteristic length (∼10nm\sim10\mathrm{nm}), the Fourier law should be sufficient to model the thermal transport14, 39, We applied Fourier’s law with the governing equation40:

∇⋅(k∇T)+g=ρc∂T∂t(1)\nabla\cdot(k\nabla T) + g = \rho c \frac{\partial T}{\partial t} \tag*{(1)}

Here, kk is the thermal conductivity, gg is the heat source, ρ\rho is density, and cc is the specific heat. We further expand the governing equation under spherical coordinates with azimuthal symmetry and simplify our model to a 2D problem (Figure 1A & Figure S1). To further simplify the model, we assume constant thermal properties. Based on our previous work, the constant property assumption introduces minimal error.14 The theoretical model is shown as follows:

The setup for the FDM model

Figure S1. The setup for the FDM model. We expanded the governing equation in spherical coordination and discretized the system with an orthogonal mesh. To separate the singularities in the radius direction and the polar angle direction, we adopt a 1D zone with isothermal in the polar angle direction around the original point. Here we use r1Dr_{1D} to denote the size of this 1D zone.

∂2T∂r2+2r∂T∂r+1r∂2T∂θ2+cot⁡(θ)r2∂T∂θ+gk=1D∂T∂t(2)\frac{\partial^2 T}{\partial r^2} + \frac{2}{r}\frac{\partial T}{\partial r} + \frac{1}{r}\frac{\partial^2 T}{\partial\theta^2} + \frac{\cot(\theta)}{r^2}\frac{\partial T}{\partial\theta} + \frac{g}{k} = \frac{1}{D}\frac{\partial T}{\partial t} \tag*{(2)}

where DD refers to thermal diffusivity. Expanding the governing equation with spherical coordinates enables us to discretize the system with an orthogonal mesh (Figure 1B & Figure S1). However, it also has some drawbacks. As shown in Equation (2), the system will have singularities when r→0r \to0 and θ→0\theta\to0 & π\pi and is discontinuous at the center point where the two singularities meet (r=0r = 0, θ=0\theta= 0).41 To overcome this, we assume the temperature is uniformly distributed in the θ\theta direction near the center point. Thus we can further reduce the governing equation in the region near the center point to a 1D problem (Figure S2). Since the thermal diffusivity of metal is much higher than that in water, the temperature profile inside the JNP is close to isothermal, and this 1D assumption is acceptable. Consequently, the temperature governing equation is given by:

Mesh independence analysis for radius direction

Figure S2. The mesh independence analysis for radius direction. (A) The truncation error in terms of mesh grid number in the radius direction under different biased mesh factor α\alpha (Δri+1=αΔri\Delta r_{i+1} = \alpha\Delta r_i). (B) Temperature contrast in terms of mesh grid number in the polar angle direction. (C) The truncation error in terms of f mesh grid number in the polar angle direction.

{∂2TJNP∂r2+2r∂TJNP∂r+gkJNP=1DJNP∂TJNP∂t,r≤r1D∂2TJNP∂r2+2r∂TJNP∂r+cot⁡(θ)r2∂TJNP∂θ+1r2∂2TJNP∂θ2+gkJNP=1DJNP∂TJNP∂t,r1D<r≤rJNP∂2Tw∂r2+2r∂Tw∂r+cot⁡(θ)r2∂Tw∂θ+1r2∂2Tw∂θ2=1Dw∂Tw∂t,r>rJNP(3)\begin{cases} \frac{\partial^{2}T_{JNP}}{\partial r^{2}}+\frac{2}{r}\frac{\partial T_{JNP}}{\partial r}+\frac{g}{k_{JNP}}=\frac{1}{D_{JNP}}\frac{\partial T_{JNP}}{\partial t}, & r\le r_{1D}\\ \frac{\partial^{2}T_{JNP}}{\partial r^{2}}+\frac{2}{r}\frac{\partial T_{JNP}}{\partial r}+\frac{\cot(\theta)}{r^{2}}\frac{\partial T_{JNP}}{\partial\theta}+\frac{1}{r^{2}}\frac{\partial^{2}T_{JNP}}{\partial\theta^{2}}+\frac{g}{k_{JNP}}=\frac{1}{D_{JNP}}\frac{\partial T_{JNP}}{\partial t}, & r_{1D}<r\le r_{JNP}\\ \frac{\partial^{2}T_{w}}{\partial r^{2}}+\frac{2}{r}\frac{\partial T_{w}}{\partial r}+\frac{\cot(\theta)}{r^{2}}\frac{\partial T_{w}}{\partial\theta}+\frac{1}{r^{2}}\frac{\partial^{2}T_{w}}{\partial\theta^{2}}=\frac{1}{D_{w}}\frac{\partial T_{w}}{\partial t}, & r>r_{JNP} \tag*{(3)} \end{cases}

The boundary and initial conductions are:

TJNP−TwR=−kJNP∂TJNP∂r=−kw∂Tw∂r,r=rJNPTw=0,r=rboundaryTJNP=0, Tw=0,t=0(4)\begin{aligned} \frac{T_{JNP}-T_{w}}{R}&=-k_{JNP}\frac{\partial T_{JNP}}{\partial r}=-k_{w}\frac{\partial T_{w}}{\partial r}, && r=r_{JNP}\\ T_{w}&=0, && r=r_{boundary}\\ T_{JNP}&=0,\ T_{w}=0, && t=0 \tag*{(4)} \end{aligned}

r1Dr_{1D} refers to the radius of the 1D region (Figure S2), rJNPr_{JNP} refers to the radius of the JNP, and rboundaryr_{boundary} refers to the radius of the boundary for the water domain. It should be noted that RR is the interfacial thermal resistance (ITR), and it is a function of θ\theta:

R={R1,0≤θ≤θ0R2,θ0<θ≤π(5)R=\begin{cases} R_{1}, & 0\le\theta\le\theta_{0}\\ R_{2}, & \theta_{0}<\theta\le\pi \end{cases} \tag*{(5)}

where R1R_{1} and R2R_{2} indicate the ITR for the coating on the northern part and the ITR for the coating on the southern part, respectively, and θ0\theta_{0} refers to the polar angle boundary between the heterogenous coatings (Figure 1A).

Equation (3)-(5) are the mathematical description of our model, and we further developed our FDM model based on Equation (3)-(5).

Finite difference method model

Next, we developed our (Finite difference method) FDM model by discretizing Equation (3)–(5).42 Here, we adopted a biased mesh in the radius direction in the water domain to achieve higher accuracy and save computational time (Figure S1). For the steady-state problem, the left-hand side of Equation (3) equals zero, and the discretized governing equation in the water domain is as follows:

AaTi−1,j+AbTi+1,j+AcTi+2,j+(Aa+Ab+Ac)Ti,j(Δr)2+2riDaTi+1,j+DbTi−1,j+(Da+Db)Ti,jΔr+1riTi,j+1−2Ti,j+Ti,j−1(Δθ)2+cot⁡(θj)(ri)2Ti,j+1−Ti,j−12Δθ=0(6)\frac{A_aT_{i-1,j}+A_bT_{i+1,j}+A_cT_{i+2,j}+(A_a+A_b+A_c)T_{i,j}}{(\Delta r)^2}+\frac{2}{r_i}\frac{D_aT_{i+1,j}+D_bT_{i-1,j}+(D_a+D_b)T_{i,j}}{\Delta r}+\frac{1}{r_i}\frac{T_{i,j+1}-2T_{i,j}+T_{i,j-1}}{(\Delta\theta)^2}+\frac{\cot(\theta_j)}{(r_i)^2}\frac{T_{i,j+1}-T_{i,j-1}}{2\Delta\theta}=0 \tag*{(6)}
Aa=2(α3+2α2+α−1)α4+3α3+2α2+α+1,Ab=2(α2+α−1)α4+2α3−α2,Ac=−2(α−1)α7+4α6+5α5+3α4−α2A_a=\frac{2(\alpha^3+2\alpha^2+\alpha-1)}{\alpha^4+3\alpha^3+2\alpha^2+\alpha+1},\quad A_b=\frac{2(\alpha^2+\alpha-1)}{\alpha^4+2\alpha^3-\alpha^2},\quad A_c=\frac{-2(\alpha-1)}{\alpha^7+4\alpha^6+5\alpha^5+3\alpha^4-\alpha^2}
Da=−αα+1,Db=1α2+αD_a=\frac{-\alpha}{\alpha+1},\quad D_b=\frac{1}{\alpha^2+\alpha}

where the subscript ii indicates the iith node in the rr direction, and jj indicates the jjth node in θ\theta direction, α\alpha indicates the biased mesh factor (Δri+1=αΔri\Delta r_{i+1}=\alpha\Delta r_i). The system has a second order of accuracy, and we validated the model by conducting a mesh-independent analysis and boundary effect analysis (Figure S2 & Figure S3).

Boundary effect analysis of the FDM model

Figure S3. The boundary effect analysis of the FDM model. (A) The error of the temperature rise in JNP by comparing the result with an analytical model that has an infinite boundary size. (B) The temperature profile comparison between the analytical solution with infinite boundary size and FDM result with boundary size = 3000 nm.

For the transient problem, we discretized Equations (3)–(5) with a Crank-Nicolson scheme,43 and the discretized governing equation in the water domain is:

12[AaTi,jn+1+AbTi+1,jn+1+AcTi+2,jn+1+(Aa+Ab+Ac)Ti,jn+1(Δr)2+AaTi,jn+AbTi+1,jn+AcTi+2,jn+(Aa+Ab+Ac)Ti,jn(Δr)2]+1ri[DaTi+1,jn+1+DbTi−1,jn+1+(Da+Db)Ti,jn+1Δr+DaTi+1,jn+DbTi−1,jn+(Da+Db)Ti,jnΔr]+1ri[Ti,j+1n+1−2Ti,jn+1+Ti,j−1n+1(Δθ)2+Ti,j+1n−2Ti,jn+Ti,j−1n(Δθ)2]+cot⁡(θj)2(ri)2[Ti,j+1n+1−Ti,j−1n+12Δθ+Ti,j+1n−Ti,j−1n2Δθ]=1DwTi,jn+1−Ti,jnΔt(7)\begin{aligned} \frac{1}{2}\Bigg[& \frac{A_aT_{i,j}^{n+1}+A_bT_{i+1,j}^{n+1}+A_cT_{i+2,j}^{n+1}+(A_a+A_b+A_c)T_{i,j}^{n+1}}{(\Delta r)^2}\\ &+\frac{A_aT_{i,j}^{n}+A_bT_{i+1,j}^{n}+A_cT_{i+2,j}^{n}+(A_a+A_b+A_c)T_{i,j}^{n}}{(\Delta r)^2}\Bigg]\\ &+\frac{1}{r_i}\left[\frac{D_aT_{i+1,j}^{n+1}+D_bT_{i-1,j}^{n+1}+(D_a+D_b)T_{i,j}^{n+1}}{\Delta r} +\frac{D_aT_{i+1,j}^{n}+D_bT_{i-1,j}^{n}+(D_a+D_b)T_{i,j}^{n}}{\Delta r}\right]\\ &+\frac{1}{r_i}\left[\frac{T_{i,j+1}^{n+1}-2T_{i,j}^{n+1}+T_{i,j-1}^{n+1}}{(\Delta\theta)^2} +\frac{T_{i,j+1}^{n}-2T_{i,j}^{n}+T_{i,j-1}^{n}}{(\Delta\theta)^2}\right]\\ &+\frac{\cot(\theta_j)}{2(r_i)^2}\left[\frac{T_{i,j+1}^{n+1}-T_{i,j-1}^{n+1}}{2\Delta\theta} +\frac{T_{i,j+1}^{n}-T_{i,j-1}^{n}}{2\Delta\theta}\right] =\frac{1}{D_w}\frac{T_{i,j}^{n+1}-T_{i,j}^{n}}{\Delta t} \tag*{(7)} \end{aligned}

where superscript nn indicates the nnth node in the time direction, we further validated the accuracy and stability of the model (Figure S4), the numerical results are in consistent with analytical solutions. Equation (6) and (7) are solved with MATLAB R2020b.

Two-panel plot showing mesh independence in the temporal direction and comparison of FDM results with the analytical solution

Figure S4. The mesh independence for temporal direction. (A) The mesh independence analysis in the temporal direction. (B) Comparison of FDM results with Δt=0.1\Delta t = 0.1 ns and the analytical solution.

Results and discussion

Directional heating and temperature contrast under continuous heating (steady-state)

Several factors can affect the thermal transport and temperature profile during JNP heating, including the interfacial thermal resistance (ITR), the size of the JNP (rJNPr_{\mathrm{JNP}}), the polar angle of the heterogeneous coatings (θ0\theta_0), and the heating time (tt). Here in this section, as we focus on the directional heating under steady-state scenarios, we start with the most idealized JNP with a θ0=π/2\theta_0=\pi/2 (Figure 1A), i.e., the JNP is heterogeneously coated equally on the two hemispheres. Nonuniform interfacial properties can stem from the heterogeneous coating, including hydrophilicity and ITR, and the contrast between ITRs can be tuned by altering the combination of coating materials or ligands.44-46 Here, we analyzed the temperature profile with different combinations of the ITRs, where R1R_1 and R2R_2 indicate the ITRs along the northern and southern hemispheres, respectively. Figure 2A shows that for a given sized JNP (rJNP=15r_{\mathrm{JNP}}=15 nm), the combination of R1R_1 and R2R_2 significantly affects the temperature profile. For case ① where R1=R2=50×10−9R_1=R_2=50\times10^{-9} m2KW−1m^2\mathrm{K}\mathrm{W}^{-1}, we have a homogeneous nanoparticle (NP) with uniform ITR; thus, the temperature is independent of the polar angle (θ\theta), and a uniform temperature jump is observed across the JNP-water interface due to ITR. As we increase the contrast between ITRs, a temperature contrast in the water domain near the north pole and south pole gradually appears, and a strong positive relationship between the ITR contrast and temperature contrast is illustrated in Figure 2A, an approximately two times difference between the temperature around the north pole and the south pole is observed for case ④ (R2/R1=100R_2/R_1 = 100). This heterogeneous thermal transport and temperature profile are known as directional heating. Here, to quantify the temperature contrast and directional heating, we developed a dimensionless parameter ζ\zeta which is defined as the ratio between the temperature rise in water at the north pole (ΔT1\Delta T_1) and the south pole (ΔT2\Delta T_2) (Figure 1B):

Image not extracted

Figure 2. Temperature profile and temperature contrast with JANUS NP under S.S. (A) Profiles for normalized temperature rise (ΔT\Delta T) with Janus nanoparticle (JNP) heating. The JNP size (rJNPr_{\mathrm{JNP}}) is 15 nm, and the cone angle for the heterogeneous coating (θ0\theta_0) is π/2\pi/2. (B) 2D map of ζs.s.\zeta_{\mathrm{s.s.}} in terms of the two ITRs, R1R_1, and R2R_2. Dotted lines are contour lines for ζs.s.\zeta_{\mathrm{s.s.}}.

ζ=ΔT1ΔT2(8)\zeta= \frac{\Delta T_1}{\Delta T_2} \tag*{(8)}

As shown in Equation (8), ζ\zeta quantifies the temperature contrast for directional heating by characterizing the relative difference between the temperature rises. For ζ=1\zeta= 1, it indicates no temperature contrast or homogeneous heating, as shown in Figure 1A, case ①. On the contrary, when ζ\zeta deviates from 1, it indicates considerable temperature contrast and directional heating (Figure 1A, case ④ ζ=2.5\zeta= 2.5).

For more generalized cases with arbitrary combinations of R1R_1 and R2R_2, we demonstrated and investigated the 2D map of ζs.s.\zeta_{\mathrm{s.s.}} in terms of R1R_1 and R2R_2 (Figure 2B), where the subscript s.s. indicating it’s under steady-state. The range for ITRs in Figure 2B (11-100×10−9 m2KW−1100 \times10^{-9}\,\mathrm{m}^2\mathrm{K}\mathrm{W}^{-1}) is consistent with ITRs reported in the literatures.14 ζs.s.\zeta_{\mathrm{s.s.}} equals to 1 along the diagonal where R1=R2R_1 = R_2. On the contrary, ζs.s.\zeta_{\mathrm{s.s.}} deviates from 1 in the off-diagonal region, denoting directional heating when R1≠R2R_1 \ne R_2. It should be noted that Figure 2B is symmetry along the diagonal line due to θ0=π/2\theta_0 = \pi/2 (Figure 1A), i.e., for an idealized JNP where the two coating areas are equal, exchange the R1R_1 and R2R_2 should lead to the inverse of ζs.s.\zeta_{\mathrm{s.s.}}. On this ζs.s.\zeta_{\mathrm{s.s.}}-ITR map, we can readily read the relative temperature contrast with arbitrary combinations of R1R_1 and R2R_2; for instance, when R1=1×10−9 m2KW−1R_1 = 1 \times10^{-9}\ \mathrm{m^2 K W^{-1}} and R2=100×10−9 m2KW−1R_2 = 100 \times10^{-9}\ \mathrm{m^2 K W^{-1}}, ζs.s.=2.5\zeta_{\mathrm{s.s.}} = 2.5, indicating significant directional heating, with the temperature rise near the north pole being 2.5 times higher than that near the south pole.

To further investigate how the combination of ITRs affects ζs.s.\zeta_{\mathrm{s.s.}}, we developed a circuit analogy model to analyze the JNP heating under steady-state analytically. Here we assume no heat transfer across the polar angle (θ0\theta_0) of heterogeneous ITR in the water domain, and we simplified the model to a parallel circuit analogy (Figure S5A) with a set of linear equations to describe the temperature at the critical nodes (Equation (10) & (11)).

Parallel circuit model for JNP heating under steady state

Figure S5. The parallel circuit model for the JNP heating under steady state.

Based on this parallel circuit model, ζs.s.\zeta_{\mathrm{s.s.}} can be estimated by:

ζs.s.=ΔT1ΔT2=rJNP+R2kWrJNP+R1kW(9)\zeta_{\mathrm{s.s.}} = \frac{\Delta T_1}{\Delta T_2} = \frac{r_{\mathrm{JNP}} + R_2 k_{\mathrm{W}}}{r_{\mathrm{JNP}} + R_1 k_{\mathrm{W}}} \tag*{(9)}

Comparing results from Equation (9) with the FDM results (Figure S5B), we show that the parallel circuit model overestimates ζs.s.\zeta_{\mathrm{s.s.}}, but is more accurate with larger JNPs. This overestimation may have arisen from the assumption of no heat transfer across θ0\theta_0, and for larger JNPs, heat flux on the θ\theta direction becomes less important, making it more accurate for larger JNPs. Overall, Equation (9) helps us better understand JNP heating and demonstrates the size dependence of temperature contrast with JNP heating. Based on Equation (9), for a given combination of R1R_1 and R2R_2, increasing rJNPr_{\mathrm{JNP}} will yield less temperature contrast. This size dependence agrees with Kapitza number analysis,47, 48

where for larger NP, the ITR has an insignificant effect on the heat dissipation. This size dependence of ζs.s.\zeta_{\mathrm{s.s.}} is also confirmed with the FDM model, and the ζs.s.\zeta_{\mathrm{s.s.}} maps with rJNP=3.75r_{\mathrm{JNP}} = 3.75 nm and rJNP=60r_{\mathrm{JNP}} = 60 nm are shown in Fig. S6.

Normalized temperature maps for panels (A) and (B), showing four maps with $R_1$ and $R_2$ values and a $\zeta_{\mathrm{s.s.}}$ map

Figure S6.

The effect of JNP size and polar angle on the temperature contrast under S.S.

Next, we focused on the effect of polar angle (θ0\theta_0) on temperature contrast under steady-state heating. In previous sections, we discussed the directional heating and temperature contrast with idealized JNPs (θ0=π/2\theta_0 = \pi/2). In reality, θ0\theta_0 can deviate from π/2\pi/2 depending on the synthesis protocol (Figure S7). 28, 49 Here, we found that θ0\theta_0 has a significant impact on the temperature profile as well as on ζs.s.\zeta_{\mathrm{s.s.}}. As illustrated in Figure S8, for a 30 nm JNP with R2/R1=100R_2/R_1 = 100, when θ0=0\theta_0 = 0, the JNP is homogeneously coated with ITR of R2R_2, leading to ζs.s.=0\zeta_{\mathrm{s.s.}} = 0 (homogeneous heating). As we slightly increase θ0\theta_0, ζs.s.\zeta_{\mathrm{s.s.}} rises drastically and reaches its peak value (∼4.2\sim4.2) at θ0∼π/12\theta_0 \sim\pi/12. After that peak point, ζs.s.\zeta_{\mathrm{s.s.}} gradually drops as we further increase θ0\theta_0, and eventually down to 1 when θ0=π\theta_0 = \pi, indicating homogenous heating as uniform ITR =R1= R_1. Here we could observe an asymmetric effect of the θ0\theta_0 on ζs.s.\zeta_{\mathrm{s.s.}} as the maximum value of ζs.s.\zeta_{\mathrm{s.s.}} is achieved for θ0<π/2\theta_0 < \pi/2 and ζs.s.(θ0=π/4)≠ζs.s.(θ0=3π/4)\zeta_{\mathrm{s.s.}}(\theta_0 = \pi/4) \ne\zeta_{\mathrm{s.s.}}(\theta_0 = 3\pi/4). The asymmetric effect of θ0\theta_0 on ζs.s.\zeta_{\mathrm{s.s.}} is also demonstrated in Figure S8.

Schematic illustration of the synthesize protocol for JNP

Figure S7. Schematic illustration of the synthesize protocol for JNP.

Effect of the polar angle for heterogeneous coating on the temperature profile

Figure S8. The effect of the polar angle for heterogeneous coating (θ0\theta_0) on the temperature profile. (A) The ΔT\Delta T profile of JNP heating with different θ0\theta_0. R1=1×10−9 m2KW−1R_1 = 1 \times10^{-9}\,\mathrm{m}^2\mathrm{K}\mathrm{W}^{-1} and R2=100×10−9 m2KW−1R_2 = 100 \times10^{-9}\,\mathrm{m}^2\mathrm{K}\mathrm{W}^{-1}, rJNP=15r_{\mathrm{JNP}} = 15

This asymmetric effect of θ0\theta_0 on ζs.s.\zeta_{\mathrm{s.s.}} can be explained by the heterogeneity of local heat flux rate (q˙\dot{q}) across the interface. The total heat flux (qq) across the JNP-water interface only depends on the heating power within JNP for steady-state scenarios and can be treated as a constant. On the contrary, the local heat flux rate (q˙\dot{q}) across the JNP-water interface interface is heavily impacted by the heterogeneous ITR. For JNPs with a high contrast of ITRs, a major fraction of heat flux is through the interface with low ITR (Figure S9B), i.e., heat flux is regulated through a window with low ITR. As we change θ0\theta_0, that window with low resistance can be narrowed or broadened, hence changing the local thermal flux rate (Figure S8B), and a much greater local heat flux rate at the north pole (q˙1\dot{q}_1) is observed for smaller θ0\theta_0 whereas the local heat flux rate at the south pole (q˙2\dot{q}_2) is less sensitive to θ0\theta_0. Consequently, greater temperature contrast comes with smaller θ0\theta_0 as the local temperature gradient is linearly proportional to the local heat flux rate.

Effect of ITR contrast on the heat flux fraction through the north and southern hemisphere

Figure S9. The effect of ITR contrast on the heat flux fraction through the north and southern hemisphere. (A) Schematic illustration of the heat flux through the north hemisphere (q1q_1) and south hemisphere (q2q_2). (B) The fraction of q1q_1 and q2q_2 with different ITR contrast.

It should be noted that for different-sized JNPs and JNPs with less ITR contrasts, all the key factors, including the ITR contrast, the JNP size, and θ0\theta_0, can have a combined nonlinear effect on the temperature contrast. Here we demonstrate this combined effect by plotting the map of ζs.s.\zeta_{\mathrm{s.s.}} in terms of rJNPr_{\mathrm{JNP}} and θ0\theta_0 with different ITR contrast under the steady state (Figure 3). Figure 3 demonstrates that the temperature contrast is more sensitive to rJNPr_{\mathrm{JNP}} and θ0\theta_0 with high ITR contrast and vice versa. Within the range of our parameter scanning, the greatest temperature contrast (ζs.s.=10\zeta_{\mathrm{s.s.}} = 10) under steady-state is observed for a 3 nm JNP with θ0∼π/12\theta_0 \sim\pi/12 and a high ITR contrast (R2/R1=100R_2/R_1 = 100). Our results provide estimations of the directional heating under realistic physical constraints, and we expect Figure 3 can provide guidelines for tuning the temperature contrast with JNP heating for novel applications.

Schematic illustration and $\zeta_{\mathrm{s.s.}}$ maps for different ITR contrasts

Figure 3. ζs.s.\zeta_{\mathrm{s.s.}} map in terms of rJNPr_{\mathrm{JNP}} and θ0\theta_0 with different ITR contrast under steady-state. (A) Schematic illustration of altering the rJNPr_{\mathrm{JNP}} and θ0\theta_0. (B-D) ζs.s.\zeta_{\mathrm{s.s.}} map in terms of rJNPr_{\mathrm{JNP}} and θ0\theta_0 with (B) R1=1×10−9 m2KW−1R_1 = 1 \times10^{-9}\,\mathrm{m}^2\mathrm{K}\mathrm{W}^{-1}, R2=100×10−9 m2KW−1R_2 = 100 \times10^{-9}\,\mathrm{m}^2\mathrm{K}\mathrm{W}^{-1}, (C) R1=9.09×10−9 m2KWR_1 = 9.09 \times10^{-9}\,\mathrm{m}^2\mathrm{K}\mathrm{W}

11, R2=90.9×10−9 m2KW−1R_2 = 90.9 \times10^{-9}\ \mathrm{m^2 K W^{-1}}, (D) R1=9.09×10−9 m2KW−1R_1 = 9.09 \times10^{-9}\ \mathrm{m^2 K W^{-1}}, R2=90.9×10−9 m2KW−1R_2 = 90.9 \times10^{-9}\ \mathrm{m^2 K W^{-1}}. The dotted line are contour lines for ζs.s.\zeta_{\mathrm{s.s.}}.

Directional heating during pulsed heating

In previous sections, we have discussed the directional heating and temperature contrast with JNP heating under the steady state, which is applicable for a microsecond or continuous heating. Recently, ultra-fast NP heating with femtosecond to nanosecond pulsed energy excitation has shown unique thermal responses and has played essential roles in various applications.50-52 As the characteristic thermal relaxation time (τ=rJNP2Dw\tau= \frac{r_{\mathrm{JNP}}^2}{D_{\mathrm{w}}}) for 30 nm JNP is around 1.6 ns, JNP heating with nanosecond or shorter pulsed heating is far from steady-state. Therefore, in this section, we analyzed the evolution of temperature contrast with JNP heating during the transient process.

Here we Imposed 100 ns pulsed constant heating on a 30 nm JNP with R2/R1=100R_2/R_1 = 100 and θ0=π/2\theta_0 = \pi/2. Figure 4A illustrates the temperature profiles during the transient heating process.

Temperature evolution during transient heating

Figure 4. The temperature evolution during the transient heating. (A) ΔT\Delta T profiles during the transient heating process with JNP. rJNP=15r_{\mathrm{JNP}} = 15 nm, heating power (gg) =35.6 μ\muW,

At t=1t = 1 ns, due to the short heating time, only a thin layer of water adjacent to the JNP-water interface is heated along the northern hemisphere, also known as thermal confinement. On the contrary, no apparent heating is observed near the southern hemisphere due to greater ITR. By comparing the local heat flux at the north pole and south pole (q˙1\dot{q}_1 and q˙2\dot{q}_2), we can see that both the magnitude and increasing rate for q˙1\dot{q}_1 are significantly higher than those for q˙2\dot{q}_2 for t<1t < 1 ns, this leads to a much-enhanced relative difference between ΔT1\Delta T_1 and ΔT2\Delta T_2 (Figure 4B), i.e., enhanced temperature contrast. Figure 4C shows that ζ\zeta can reach to ∼20\sim20 when t=0.1t = 0.1 ns. As heating continuous, thermal energy continuously diffuses, and both ΔT1\Delta T_1 and ΔT2\Delta T_2 rise; However, the increasing rate for ΔT2\Delta T_2 is greater than that of ΔT1\Delta T_1, ending up with a reducing ζ\zeta as demonstrated in Figure 4C. For t=100t = 100 ns, the maximum temperature is reached as it is the end time point for the pulsed heating (Figure 4A). At this time-point, ΔT1\Delta T_1 and ΔT2\Delta T_2 asymptotically tend to its steady-state value (Figure 4B, Fo=63.5Fo = 63.5), and ζ\zeta asymptotically falls to its steady-state level (Figure 4C, ζs.s.=2.5\zeta_{\mathrm{s.s.}} = 2.5). After the pulsed heating (t>100t > 100 ns), the hole system cools down rapidly, and both ΔT1\Delta T_1 and ΔT2\Delta T_2 drop to 0 with ζ\zeta falls to 1. To summarize, we found that ΔT2\Delta T_2 is minimal for small FoFo, leading to a significant enhancement of temperature contrast, and eight times enhancement of ζ\zeta is observed when Fo=0.06Fo = 0.06 (R2/R1=100R_2/R_1 = 100, rJNP=15r_{\mathrm{JNP}} = 15 nm, θ0=π/2\theta_0 = \pi/2), i.e., pulsed JNP heating can lead to a greater temperature contrast.

heating time (theatingt_{\mathrm{heating}}) = 100 ns. R1=1×10−9 m2KW−1R_1 = 1 \times10^{-9}\ \mathrm{m^2 K W^{-1}}, R2=100×10−9 m2KW−1R_2 = 100 \times10^{-9}\ \mathrm{m^2 K W^{-1}}, θ0=π/2\theta_0 = \pi/2. (B) The evolution of local heat flux rate (q˙\dot{q}) at the north pole and south pole during the transient heating process. (C) The evolution of ΔT1\Delta T_1 and ΔT2\Delta T_2 during the transient heating process. (D) The evolution of ζ\zeta during the transient heating process, the blue dotted line indicates the corresponding ζs.s.\zeta_{\mathrm{s.s.}}.

The effect of rJNPr_{\mathrm{JNP}} and θ0\theta_0 on temperature contrast during the transient process

In the previous section, we discussed directional heating during the transient heating process and found an enhancement of temperature contrast with puled JNP heating. This section will expand our investigation into more generalized cases and discuss the combined effects of geometric parameters (rJNPr_{\mathrm{JNP}} and θ0\theta_0) on temperature contrast during the transient heating process.

We start with the effect of the size of the JNP (rJNPr_{\mathrm{JNP}}) on ζ\zeta during the transient process. In our previous sections, we demonstrated a strong size dependence of ζ\zeta for the steady-state conditions (Figure 3-D and Fig. S6). As shown in Figure 5A, we can observe a strong size dependence for ζ\zeta throughout the transient process as well. Smaller JNPs are more sensitive to heating time and hence have a stronger enhanced temperature contrast with pulsed heating. Additionally, we analyzed the effect of θ0\theta_0 in the transient process. Figure 5B illustrates the 2D map of ζ\zeta in terms of tt and θ0\theta_0. For θ0\theta_0 close to 0 and π\pi, JNP turns into homogeneous NP, and ζ\zeta keeps close to 1 throughout the transient heating process. For a moderate θ0\theta_0 (π/12<θ0<3π/4\pi/12 < \theta_0 < 3\pi/4), we observe an enhancement of ζ\zeta for shorter heating time. Unlike rJNPr_{\mathrm{JNP}}, which has a monotonic effect on ζ\zeta throughout time, ζ\zeta is less sensitive to θ0\theta_0 at a low FoFo number (∼0.1\sim0.1) within this medium θ0\theta_0 range. As heating continues, ζ\zeta becomes more sensitive to θ0\theta_0 as it tends to the steady-state scenario shown in Figure S8. Lastly, Fig. 5C demonstrates ζ\zeta in terms of ITR contrast and heating time, and we found that for high ITR contrast (R2/R1>25R_{2}/R_{1} > 25), the temperature contrast is significantly enhanced with short heating time (ζ∼12–20\zeta\sim12\text{--}20 when Fo∼0.1Fo \sim0.1). Whereas for low ITR contrast (R2/R1<25R_{2}/R_{1} < 25), ζ\zeta is less sensitive to heating time, and for minimal ITR contrast (R2/R1∼1–2R_{2}/R_{1} \sim1\text{--}2), ζ\zeta approximately keeps constant (ζ∼1.5\zeta\sim1.5) throughout the transient process. In conclusion, we demonstrate the combined affections of the ITRs, the geometries (rJNPr_{\mathrm{JNP}} and θ0\theta_{0}), and the heating time on the temperature contrast. In general, smaller-sized JNP with high ITR contrast and moderate polar angle can be more sensitive to heating time and can lead to a greater temperature contrast with pulsed heating. As the first effort to shed light on the pulsed JNP heating during the transient process, we anticipate Figure 4&Figure 5 to advance our understanding of the thermal transport with JNP heating, bringing inspiration for further work and providing route maps for developing novel applications.

Effect of thermal resistance, polar angle, and particle size on temperature contrast

Figure 5. The effect of thermal resistance (R2/R1R_2/R_1), polar angle (θ0\theta_0), and size of the particle (rJNPr_{\mathrm{JNP}}) on temperature contrast during the transient process. (A) ζ\zeta map in terms of ITR contrast (R2/R1R_2/R_1) and heating time (tt). Here we regulate R2+R1=100 m2 KW−1R_2 + R_1 = 100\ \mathrm{m^2\,KW^{-1}}

1 and alter R2/R1R_2/R_1 (B) ζ\zeta map in terms of rJNPr_{\mathrm{JNP}} and FoFo. (C) ζ\zeta map in terms of θ0\theta_0 and tt. The dotted lines are contour lines for ζ\zeta.

Conclusion

In this work, we focused on thermal transport and directional heating with Janus nanoparticle (JNP) heating. We developed an FDM numerical framework and defined a dimensionless parameter (ζ≡ΔT1ΔT2\zeta\equiv\frac{\Delta T_1}{\Delta T_2}) to characterize the temperature contrast. Based on this, we analyzed the effect of ITR contrast, rJNPr_{\mathrm{JNP}}, and θ0\theta_0 on temperature contrast under steady-state and transient heating. First, we found a significant size dependence of temperature contrast, where a smaller JNP can lead to greater temperature contrast. Additionally, we reveal the role of θ0\theta_0 and demonstrate its asymmetric effect on temperature contrast, finding that the maximum ζ\zeta is observed at θ0∼π/12\theta_0 \sim\pi/12. Importantly, we shed light on the temperature evolution near a JNP during a transient heating process and found a significant enhancement of the temperature contrast with pulsed JNP heating. We expect our work can help us better understand thermal transport with JNP heating and advance the field with new inspirations.

Acknowledgment

I am grateful for the useful suggestions from Dr. Yaning Liu and Dr. Hui Ouyang.

Research reported in this publication was supported by National Institute of General Medical Sciences and National Institute of Allergy and Infectious Diseases of the National Institutes of Health under award numbers R35GM133653 and R01AI151374, the National Science Foundation under award number 2123971, and the American Heart Association under award number 19CSLOI34770004. The content is solely the responsibility of the authors and does not necessarily represent the official views of funding agencies.

Associated Content

Supporting information (Docx)

Author Information

Corresponding Author: Zhenpeng Qin*

Department of Mechanical Engineering, University of Texas at Dallas, 800 West Campbell Road EW31, Richardson, Texas 75080, United States.

E-mail: [email protected]

ORICD: 0000-0003-3406-3045

Author Contributions

C.X. developed the numerical model and did the computational work and analysis. B.W. and Z.Q. participated in conceptualization and analysis. All authors contributed to the writing of the manuscript. Z.Q. directed the research.

Funding

The research reported in this work was partially supported by the National Institute of General Medical Sciences (NIGMS) of the National Institutes of Health (award number R35GM133653), the Collaborative Sciences Award from the American Heart Association (award number 19CSLOI34770004), and the High-Impact/High-Risk Research Award from the Cancer Prevention and Research Institute of Texas (award number RP180846). The content is the sole responsibility of the authors and does not necessarily represent the official views of the funding agencies.

Nomenclature

Roman letters

R1R_{1} Interfacial thermal resistance along the north hemisphere of Janus nanoparticle, m2 K W−1\mathrm{m}^{2}\,\mathrm{K}\,\mathrm{W}^{-1}

R2R_{2} Interfacial thermal resistance along the south hemisphere of Janus nanoparticle, m2 K W−1\mathrm{m}^{2}\,\mathrm{K}\,\mathrm{W}^{-1}

kk Thermal conductivity, W m−2 K−1\mathrm{W}\,\mathrm{m}^{-2}\,\mathrm{K}^{-1}

kJNPk_{\mathrm{JNP}} Thermal conductivity in Janus nanoparticle, W m−2 K−1\mathrm{W}\,\mathrm{m}^{-2}\,\mathrm{K}^{-1}

kwk_{\mathrm{w}} Thermal conductivity in water, W m−2 K−1\mathrm{W}\,\mathrm{m}^{-2}\,\mathrm{K}^{-1}

TT Temperature, K

TJNPT_{\mathrm{JNP}} Temperature in the Janus nanoparticle, K

SymbolDefinition
TwT_{\mathrm{w}}Temperature in water, K
ggHeating power, W m−3^{-3}
ccSpecific heat, J kg−1^{-1}
ttTime, s
rrRadius, m
r1Dr_{\mathrm{1D}}Radius of the 1D zone, m
rJNPr_{\mathrm{JNP}}Radius of the Janus nanoparticle, m
rboundaryr_{\mathrm{boundary}}Radius of the water domain, m
DDThermal diffusivity, m2^{2} s−1^{-1}
DJNPD_{\mathrm{JNP}}Thermal diffusivity in Janus nanoparticle, m2^{2} s−1^{-1}
DwD_{\mathrm{w}}Thermal diffusivity in water, m2^{2} s−1^{-1}
RRInterfacial thermal resistance, m2^{2} K W−1^{-1}
R1R_{1}Interfacial thermal resistance on the north hemisphere, m2^{2} K W−1^{-1}
R2R_{2}Interfacial thermal resistance on the southern hemisphere, m2^{2} K W−1^{-1}
KaKaKaptiza number, Ka≡RkrKa \equiv\frac{Rk}{r}
Ka1Ka_{1}Kaptiza number on the north hemisphere, Ka1≡R1krJNPKa_{1} \equiv\frac{R_{1}k}{r_{\mathrm{JNP}}}
Ka2Ka_{2}Kaptiza number on the southern hemisphere, Ka2≡R2krJNPKa_{2} \equiv\frac{R_{2}k}{r_{\mathrm{JNP}}}
qqHeat flux, W

Table 1.

q1q_{1} Heat flux through the north hemisphere, W

q2q_{2} Heat flux through the southern hemisphere, W

q˙\dot{q} Heat flux rate, Wm−2^{-2}

q˙1\dot{q}_{1} Heat flux rate at the north pole, Wm−2^{-2}

q˙2\dot{q}_{2} Heat flux rate at the south pole, Wm−2^{-2}

FoFo Fourier number, Fo≡DtrJNP2Fo \equiv\frac{Dt}{r_{\mathrm{JNP}}^{2}}

Greek symbols

θ\theta Polar angle

θ0\theta_{0} The critical polar angle that pinpoints the boundary between the heterogeneous interfacial thermal resistances.

ζ\zeta Dimensionless parameter to characterize the temperature contrast, ζ≡ΔT1ΔT2\zeta\equiv\frac{\Delta T_{1}}{\Delta T_{2}}

ζs.s.\zeta_{\mathrm{s.s.}} Dimensionless parameter to characterize the temperature contrast for steady-state.

ρ\rho Density, kg m−3^{-3}

τ\tau Characteristic thermal relaxation time, τ≡r2D\tau\equiv\frac{r^{2}}{D}, s

Abbreviations

JNP Janus nanoparticle

ITR Interfacial thermal resistance

MD Molecular dynamic

FDM Finite difference method

S.S. Steady-state

REGULATING NANOSCALE HEAT TRNSFER WITH JANUS NANOPARTICLES

Supporting information for

This PDF file includes:

  • Equations S1 to S3

  • Figures S1 to S9

We validated our model by doing a comprehensive mesh dependency analysis. Here, we start with the mesh in the radius and the polar direction for the steady-state model. We assume uniform interfacial thermal resistance (ITR) along the JNP-water interface, thus making a homogenous NP heating where the analytical solution is available. As we have a linear biased mesh grid in the radius direction, we analyzed the truncation error by comparing the FDM results with the analytical solution with different biased mesh factor α\alpha (Δri+1=αΔri\Delta r_{i+1} = \alpha\Delta r_i) and mesh density. The error is calculated by the following equation:

error=abs(ΔTanalytical−ΔTFDM)ΔTanalytical×100%(10)error = \frac{abs\left(\Delta T_{analytical} - \Delta T_{FDM}\right)}{\Delta T_{analytical}} \times100\% \tag*{(10)}

As shown in Figure S2A, when α=1\alpha= 1, we have a uniform mesh, and the truncation error drops as we increase the mesh density; when the mesh grid number is 140, the error is around 1%. When α=1.05\alpha= 1.05, we have a biased mesh, and the error drops much faster as the mesh density increases; when the mesh grid number is 50, the error is around 0.1%. This is because the biased mesh gives a higher mesh density near the JNP where the greatest temperature gradient is observed (Figure S1), and thus greatly reduces the error and makes the mesh more efficient. As we continuously increase α\alpha (α=1.1\alpha= 1.1), we found that the FDM results become less stable as we increase the mesh density. This might be because the over-biased mesh has coarse mesh grids near the boundary, which can bring extra error. In summary, we validate our model in the radius direction; we found a properly biased mesh factor (α=1.05\alpha= 1.05) and a mesh density (50, minimum Δr=0.45\Delta r = 0.45 nm); based on this setup, the truncation error is at the order of 0.1%.

Next, we did the mesh independence analysis in the polar angle (θ\theta) direction. Here we introduced a heterogeneous ITR and investigated the temperature contrast (ΔT1ΔT2\frac{\Delta T_1}{\Delta T_2}) with different mesh densities. Figure S2B demonstrates that the value of ΔT1ΔT2\frac{\Delta T_1}{\Delta T_2} converges as the mesh density increases. Here we assume the results at mesh grid = 275 is the accurate solution, and we calculate the error by comparing the results with this accurate solution (Figure S2C); we could see the error is at the magnitude of 0.1% for the mesh grid = 100 (Δθ=π/100\Delta\theta= \pi/100).

We chose a truncation error of 0.1% that indicates sufficient accuracy for our mesh set-up; thus, we will keep the set-up (α=1.05\alpha= 1.05, minimum Δr=0.45\Delta r = 0.45 nm, Δθ=π/100\Delta\theta= \pi/100) for the steady-state modeling throughout our paper.

Next, we analyzed the boundary effect. In reality, a free JNP can be treated as a single JNP surrounded by infinite water. In our model, we cannot have an infinite water domain, and the size of the boundary of the water domain can bring error, i.e., boundary effect. Here we calculated the error of boundary effect by comparing the FDM result with a finite boundary radius and the analytical solution with an infinite boundary size. As shown in Figure S3A, for boundary radius = 3000 nm (200 × rJNPr_{\mathrm{JNP}}) the error of boundary effect drops to 1%, and we believe this is accurate for our analysis (Figure S3B). We will keep this set-up throughout our paper.

Finally, we analyzed mesh independence and validated the model in the temporal direction. The spatial mesh set-ups are identical to the steady-state model. Here we plot the FDM results in terms of temporal mesh density (Figure S4A), we found that the FDM results converge as mesh density increases, and we believe a temporal mesh interval of 0.1 ns can bring sufficiently accurate results. Here we further compared the FDM result with the analytical solution (Figure S4B),1 and demonstrated that the FDM results are consistent with the analytical solutions.

For the parallel circuit model, the thermal transport with JNP can be described with a set of linear equations:

[1R1−(1R1+kwrJNP)01R10−(1R2+krJNP)(A1R1+A2R2)−A1R1−A2R2][ΔTJNPΔT1ΔT2]=[Q00](11)\begin{bmatrix} \frac{1}{R_1} & -\left(\frac{1}{R_1}+\frac{k_w}{r_{JNP}}\right) & 0 \\ \frac{1}{R_1} & 0 & -\left(\frac{1}{R_2}+\frac{k}{r_{JNP}}\right) \\ \left(\frac{A_1}{R_1}+\frac{A_2}{R_2}\right) & -\frac{A_1}{R_1} & -\frac{A_2}{R_2} \end{bmatrix} \begin{bmatrix} \Delta T_{JNP} \\ \Delta T_1 \\ \Delta T_2 \end{bmatrix} = \begin{bmatrix} Q \\ 0 \\ 0 \tag*{(11)} \end{bmatrix}
A1=2πrJNP2(1−cos⁡(θ0))A2=2πrJNP2(1+cos⁡(θ0))\begin{aligned} A_1 &= 2\pi r_{JNP}^{2}(1-\cos(\theta_0)) \\ A_2 &= 2\pi r_{JNP}^{2}(1+\cos(\theta_0)) \end{aligned}

By solving Equation (11), we have the temperature rise at the north pole and south pole:

[ΔTJNPΔT1ΔT2]=[Q(rJNP+R1k)(rJNP+R2k)A1krJNP+A2krJNP+A1k2rJNP+A2k2rJNPQrJNP(rJNP+R2k)A1krJNP+A2krJNP+A1k2rJNP+A2k2rJNPQrJNP(rJNP+R1k)A1krJNP+A2krJNP+A1k2rJNP+A2k2rJNP](12)\begin{bmatrix} \Delta T_{JNP} \\ \Delta T_1 \\ \Delta T_2 \end{bmatrix} = \begin{bmatrix} \frac{Q(r_{JNP}+R_1k)(r_{JNP}+R_2k)} {A_1kr_{JNP}+A_2kr_{JNP}+A_1k^2r_{JNP}+A_2k^2r_{JNP}} \\ \frac{Qr_{JNP}(r_{JNP}+R_2k)} {A_1kr_{JNP}+A_2kr_{JNP}+A_1k^2r_{JNP}+A_2k^2r_{JNP}} \\ \frac{Qr_{JNP}(r_{JNP}+R_1k)} {A_1kr_{JNP}+A_2kr_{JNP}+A_1k^2r_{JNP}+A_2k^2r_{JNP}} \tag*{(12)} \end{bmatrix}
ζs.s. map in terms of R1 and R2 with different rJNP and θ0.

Figure S6 (PDF p. 37). ζs.s.\zeta_{\mathrm{s.s.}} map in terms of R1R_1 and R2R_2 with different rJNPr_{\mathrm{JNP}} and θ0\theta_0.

nm. (B) The local heat flux rate across the interface at northern pole (q˙1\dot{q}_1) and southern pole (q˙2\dot{q}_2) in terms of θ0\theta_0. (C) ΔT1\Delta T_1 and ΔT2\Delta T_2 in terms of θ0\theta_0. (D) ζs.s.\zeta_{\mathrm{s.s.}} in terms of θ0\theta_0.

Reference:

References

  1. [1]Goldenberg, H.; Tranter, C., Heat flow in an infinite medium heated by a sphere. British Journal of Applied Physics 1952, 3 (9), 296.

Paper details

vlnc:W_4jf2dqss
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents