WorksPhysics and Astronomy
First principles investigation of thermal conductivity in Magnesium Selenide(MgSe) with different crystalline phase
Abstract
Magnesium Selenide (MgSe) is a wide bandgap semiconductor with applications in optoelectronics and energy conversion technologies. Understanding thermal conductivity (k) of MgSe is critical for optimum design of thermal transport in these applications. In this work, we report the temperature and length dependence lattice thermal conductivity of magnesium selenide (MgSe) with different crystallographic phases; zincblende, rocksalt, wurtzite and nickel arsenic, using first principles computations. Computations reveal significant differences in thermal conductivity (k) of MgSe for different phases. The observed trend in thermal conductivities is : kNiAs < krocksalt < kwurtzite < kzincblende. Our first principles calculations show a room temperature low k of 4.5 Wm-1K-1 for the NiAs phase and a high k of 20.4 W/mK for wurtzite phase. These differences are explained in terms of a phonon band gap in the vibrational spectra of zincblende and wurtzite phases, which suppresses scattering of acoustic phonons, leading to high phonon lifetimes.
Introduction: Wide bandgap materials have attracted scientific and technological interest due to several unique properties such as reduced energy consumption, low power loss, ability to accommodate high operating temperatures, high switching speed and high frequencies[1, 2, 3] and good thermoelectric energy conversion[4, 5, 6, 7]. Magnesium chalcogenides such as magnesium sulphide (MgS), magnesium selenide (MgSe) and magnesium telluride (MgTe) are wide bandgap semiconductors which are extensively studied for their electronic[8, 9, 10], magnetic[9], optical[8], structural[9], [11, 12, 13] and vibrational[14], [15] properties. Understanding thermal conductivity of these materials is critical for optimum thermal design of devices based on these materials. There are, however, limited studies on thermal properties which is critical for wide range of applications such as thermoelectrics[16, 17, 18, 19, 20, 21], thermal management systems[22, 23, 24, 25, 26, 27], opto-electronics[28], thermal barrier coatings[29, 30, 31] and solar cells[32, 33, 34]. In this work, we report the temperature and size dependent thermal conductivity of magnesium selenide () with different crystalline phases using first principles calculations. exists in four crystalline phases; zincblende (ZB), rocksalt (RS), wurtzite (WZ) and nickel arsenic (NiAs)[14]. At 300 K, the first principles computed thermal conductivities of are – a) along -axis and along -axis for NiAs structure, b) for Rocksalt structure, c) along -axis and along -axis for WZ structure and d) for Zinc-Blende structure. Understanding of differences in thermal conductivity is achieved through analysis of differences in phonon scattering arising from different phonon dispersions for different structures.
Computational Methods
All the first principles calculations were performed using QUANTUM ESPRESSO[35] package. Norm-conserving pseudopotentials with local density (LDA)[36] exchange-correlation functional are used for electronic calculations. The geometries of the zinc-blende and rocksalt with 2 atom unit cell and wurtzite and NiAs structures with 4 atom unit cell, were optimized until forces on all atoms were less than Ry/bohr. Plane-wave energy cutoff of 70 Ry was used for electronic calculations. Monkhorst-Pack[37] -point mesh sizes of 8 x 8 x 8 and 12 x 12 x 8 were used for zincblende/rocksalt and wurtzite/NiAs structures, respectively, to integrate over the Brillouin zone.

Figure 1a-d. Crystal structure of MgSe with crystalline phases; NiAs (a=7.216 bohr, c/a=1.6672), wurtzite (a=7.924 bohr, c/a=1.6149), rocksalt (a=10.2617 bohr) and zincblende (a=11.16 bohr) respectively.
Relaxed structures with equilibrium lattice constants of MgSe with different lattice crystal phases are shown in Fig 1 and also listed in Table 1 (in excellent agreement with previously published values[10, 14, 38, 39, 40]).
| S. No | Crystal phase | a (bohr) | c/a | B (GPa) | E(GPa) | G(GPa) | ν |
| 1. | Nickel arsenic (NiAs) | 7.216 | 1.667 | 67.36 | 92.8 | 36.53 | 0.2703 |
| 2. | Wurtzite (WZ) | 7.9238 | 1.615 | 50.7 | 55.34 | 21 | 0.3182 |
| 3. | Rocksalt (RS) | 10.2617 | 67.7 | 113.07 | 46.28 | 0.2216 | |
| 4. | Zincblende (ZB) | 11.16 | 49.695 | 47.903 | 17.933 | 0.3356 |
Table 1. Lattice constants, Bulk modulus(B), Youngs modulus(E), Shear modulus(G) and poisson’s(u) ratio of MgSe with different crystal phase.
Lattice thermal conductivity () was computed by solving phonon Boltzmann transport equation (PBTE)[41] in both single mode relaxation approximation (SMRT)[42] and exactly by using a variational method. Expression for thermal conductivity () obtained by solving PBTE in the single mode relaxation time (SMRT) approximation[43] is given by,
where, , , , , , , are the cartesian direction, Planck constant, size of the mesh, unit cell volume, Boltzmann constant, and absolute temperature respectively. represents the vibrational mode () ( is the wave vector and represent phonon polarization). , , and () are the phonon frequency, equilibrium Bose-Einstein population and group velocity along cartesian direction , respectively of a phonon mode . , , and are derived from the knowledge of phonon dispersion computed using order IFCs. is the phonon lifetime and is computed using the equation,
where, is the anharmonic scattering rate based on the lowest order three phonon interactions and are the three-phonon coupling matrix elements computed using both harmonic ( order) and anharmonic ( order) interatomic force constants. and order interatomic force constants were derived from density-functional perturbation theory (DFPT)[44, 45]. Harmonic force constants were computed on an 8 x 8 x 8 -grid for ZB and RS systems and on a 9 x 9 x 6 grid for WZ and NiAs structures. Anharmonic force constants were computed on a 4 x 4 x 4 grid for ZB and RS and on a 3 x 3 x 2 grid for WZ and NiAs structures, using D3Q[41, 46, 47] package within QUANTUM-ESPRESSO. Acoustic sum rules were imposed on both harmonic and anharmonic interatomic force constants. Phonon linewidth and lattice thermal conductivity were calculated using ‘thermal2’ package within QUANTUM ESPRESSO. For these calculations, -mesh of was used for ZB and RS structures, while a mesh of was used for WZ and NiAs structures. Iterations in the exact solution of the PBTE were performed until between consecutive iterations diminished to below . values were typically converged after 4 iterations. Casimir scattering[48] was imposed to include the effect of boundary scattering for
computing length dependent thermal conductivity in the nanoscales. Phonon-isotope scattering is included for the effect of isotope variation with naturally occurring isotopes of Mg and Se[49]. Elastic constants were computed using QUANTUM ESPRESSO thermo_pw package. Voigt-Reuss-Hill approximation[50] was used to calculate Bulk modulus, Shear modulus(G), Young’s Modulus(E) and Poisson’s ratio ().
Results and Discussion: Phonon dispersion and phonon density of states (PDOS) for the MgSe with crystalline phases of zincblende(ZB), wurtzite (WZ), rocksalt(RS) and nickel arsenic(NiAs) are shown in Figure 2 a-Figure 2d. Computed dispersions are in good agreement with previously reported values[14]. Elastic properties such as Young’s modulus (E), Bulk modulus (B), Shear modulus (G) and Poisson’s ratio based on Voigt-Ruess-Hill approximation are listed in Table 1 and are also in excellent agreement with the previously published work[14].

Figure 2. Phonon dispersion and phonon density of states(PDOS) of MgSe with crystalline phase; a) zincblende b) wurtzite c) rocksalt and d) nickel arsenic.
Temperature dependent lattice thermal conductivity () of MgSe for different crystalline phases is shown in Figure 3a. Single-mode relaxation results (SMA) are 5% less than the iterative solution. At room temperature (300K), computed of pure MgSe is as follows: (4.54 WmK along a-axis and 6.37 WmK along c-axis) < (11.89 WmK) < (19.58 WmK along a-axis and 20.39 WmK along c-axis) < (21.27 WmK). Figure 3b shows the length dependent thermal conductivity of MgSe between 10 nm and 1µm. At 300K and at 100 nm, of different crystalline

Figure 3. Temperature dependent lattice thermal conductivity of isotopically pure MgSe with different crystalline phase with a) iterative solution of BTE b) Length dependent thermal conductivity of MgSe at room temperature(300K).
phases are as follows: (3.25 WmK along a-axis and 4.67 WmK along c-axis) < (5.71 WmK) < (8.05 WmK a-axis and 8.76 WmK along c-axis) < (8.82 WmK).
Lattice thermal conductivity of naturally occurring MgSe, which includes the effect of isotopic disorder is shown in Figure 4. Thermal conductivity of naturally occurring MgSe at 300K is as follows: (4.36 WmK along a-axis and 6.13 WmK along c-axis) < (11.31 WmK) < (17.5 WmK a-axis and 18.3 WmK along c-axis) < (19.04 WmK). These values show that isotopic scattering reduces lattice thermal conductivity by a maximum of ~10% for ZB and WZ phase.

Figure 4. Figure 4a and b) Temperature and length dependent (300 K) thermal conductivity of natural MgSe for different crystalline phase.
As seen above, thermal conductivity of the NiAs crystal phase is the lowest, while that of zincblende phase is the highest. Thermal conductivity of MgSe with zincblende crystal structure is 4.68 times that of the NiAs phase along a-axis at 300 K. In Figure 5, we also compare contributions of different vibrational modes to overall thermal conductivity in different crystalline phases. Interestingly, in NiAs and wurtzite MgSe, contribution of optical phonons is significantly higher than for the case of zincblende and rocksalt phases.

Figure 5. Mode contribution thermal conductivity of MgSe at 300K for different crystalline phase.
The higher thermal conductivity of zincblende phase is due to the suppression of three-phonon scattering mediated by a large phonon bandgap (~100 cm) in the phonon dispersion of zinc-blende structure. We have presented the phonon scattering rates (inverse of phonon lifetime) and phonon group velocities of MgSe with different crystalline phases in Figure 6. We can observe from Figure 6a and Figure 6d that, scattering rate of transverse acoustic modes, and , for NiAs is approximately one order of magnitude higher than that of the zincblende phase. This causes a dramatic reduction in thermal conductivity contributions of and phonon modes in NiAs structure, reducing the overall thermal conductivity.

Figure 6. Phonon group velocity and scattering of MgSe with crystalline phase; a) zincblende b) wurtzite c) rocksalt and d) nickel arsenic
The above difference in scattering rates can be understood by observing that anharmonic scattering of phonons through the lowest-order three phonon processes can be classified into two
categories - absorption scattering process, where a phonon mode () scatters by absorbing another phonon mode (), yielding a higher energy () phonon mode, and decay processes, where a phonon mode decays into two lower energy phonons. These processes satisfy energy and momentum conservation given by, (energy), (momentum) for absorption process and (energy), (momentum) for decay process.
The large energy gap in the phonon dispersion of zincblende structure suppresses the absorption scattering channels for acoustic phonons involving scattering of an acoustic phonon by absorbing another acoustic phonon to convert into an optical phonon. The large energy gap in the phonon dispersion of the zinc-blende structure prohibits energy conservation () for such absorption scattering channels. This is seen through an example, where, an acoustic phonon of frequency cannot scatter into an optical phonon, even by absorbing the highest frequency acoustic phonon (). This is because the lowest optical phonon frequency
is higher than the sum of the frequencies of above two listed acoustic phonons. This elimination of absorption scattering channels in zinc-blende structure dramatically decreases overall scattering rates in zinc-blende case. We have shown this for all crystalline phases in Figure 7, where we compare the magnitude of absorption scattering channel with the overall scattering rates.

Figure 7. Role of absorption scattering channels in overall phonon scattering of MgSe with crystalline phase; a)zincblende b) wurtzite c) rocksalt and d) nickel arsenic
It can be seen that for zincblende and wurtzite structures (with a large bandgap in their phonon dispersions), the magnitude of absorption channels is significantly smaller than for the case of rocksalt and NiAs structures. Below a frequency of 100 , the absorption channel is seen to be almost completely absent in zinc-blende and wurtzite structures. This smaller rate of absorption scattering in zincblende and wurtzite structures also leads to a smaller overall scattering rate in these structures. At a frequency of 50 , the overall scattering rate in zinc-blende and wurtzite structures is ~0.1 , almost an order of magnitude lower, relative to the scattering rate of 1 in NiAs structure. The higher scattering rates in rocksalt and NiAs structures (due to smaller or absent phonon band gap) lead to lower thermal conductivity in these crystalline phases.
Higher contribution of optical phonon modes to overall thermal conductivity in NiAs and Wurtzite structures can now be understood in terms of the phonon band gap in these materials. In NiAs structure, the large scattering rates of acoustic phonons (due to absence of a band gap in phonon dispersion), imply that the scattering rates of low frequency optical phonons become comparable to that of acoustic phonons. Significant group velocities of optical phonons in NiAs structure combined with comparable phonon scattering rates to acoustic phonons, leads to high thermal conductivity contribution of optical phonons in NiAs structure. In Wurtzite crystalline phase, the high thermal conductivity of optical phonons arises due to the large phonon band gap in the dispersion. Figure 2b shows that some of the optical phonons are below the band gap. Similar to the case of acoustic phonons, these optical phonons also experience inhibited scattering from optical phonons above the band gap, resulting in an increase in their lifetimes. These higher lifetimes result in a higher contribution of optical phonons to overall thermal conductivity in wurtzite structure.
Conclusion: In this work, thermal conductivities of magnesium selenide (MgSe) with four crystalline phases; zincblende, rocksalt, wurtzite and nickel arsenic were computed through first principles calculations. Computations reveal significant differences in thermal conductivities of different phases; at 300 K, lowest value of 4.54 W/mK (along a-axis) is obtained for NiAs phase, while highest value of 21.27 W/mK is obtained for zincblende phase. These differences are found to be due to a large energy gap in the phonon dispersion of zincblende and wurtzite structures, which suppresses scattering of acoustic phonons by optical phonons, leading to longer phonon lifetimes and higher thermal conductivity in zincblende and wurtzite phases. Isotopic disorder scattering has minimal effect (less than 10%) on overall thermal conductivity. First principles calculations further reveal NiAs and wurtzite phases to have significant contributions from optical phonons. This effect is again explained in terms of the phonon band gap. At nanometer length scales such as 100 nm, thermal conductivity of less than 3.25 for MgSe with NiAs crystalline phase, shows a promising application of MgSe for thermoelectric technologies.
Acknowledgements: R.M and J.G would like to acknowledge OU Supercomputing Center for Education Research (OSCER) for providing computational resources. J.G and R.M acknowledge financial support from NSF CAREER grant, Award # 1847129.
References
- [1]Baliga, B. J., 1 - Introduction. In Wide Bandgap Semiconductor Power Devices, Baliga, B. J., Ed. Woodhead Publishing: 2019; pp 1-19.
- [2]di Forte-Poisson, M. A.; Magis, M.; Tordjmann, M.; di Persio, J., Chapter 5 - MOCVD Growth of Group III Nitrides for High-power, High-frequency Applications. In Optoelectronic Devices: III Nitrides, Razeghi, M.; Henini, M., Eds. Elsevier: Oxford, 2005; pp 69-94.
- [3]Millán, J.; Godignon, P. In Wide Band Gap power semiconductor devices, 2013 Spanish Conference on Electron Devices, 12-14 Feb. 2013; 2013; pp 293-296.
- [4]Xiao, Y.; Zhao, L.-D., Seeking new, highly effective thermoelectrics. Science 2020, 367 (6483), 1196.DOI
- [5]Kucukgok, B. THERMOELECTRIC PHENOMENA FOR WASTE HEAT HARVESTING USING WIDE BANDGAP SEMICONDUCTORS. The University of North Carolina at Charlotte, 2015.
- [6]Kucukgok, B.; He, Q.; Carlson, A.; Melton, A. G.; Ferguson, I. T.; Lu, N., Investigation of Wide Bandgap Semiconductors for Thermoelectric Applications. MRS Proceedings 2013, 1490, 161-166.
- [7]Liu, M.-L.; Huang, F.-Q.; Chen, L.-D.; Chen, I.-W., A wide-band-gap p-type thermoelectric material based on quaternary chalcogenides of Cu2ZnSnQ4 (Q=S,Se). Applied Physics Letters 2009, 94 (20), 202103.
- [8]Drief, F.; Tadjer, A.; Mesri, D.; Aourag, H., First principles study of structural, electronic, elastic and optical properties of MgS, MgSe and MgTe. Catalysis Today 2004, 89 (3), 343-355.DOI
- [9]Sajjad, M.; Zhang, H. X.; Noor, N. A.; Alay-e-Abbas, S. M.; Younas, M.; Abid, M.; Shaukat, A., Theoretical Investigation of Structural, Electronic, and Magnetic Properties of V-Doped MgSe and MgTe Semiconductors. Journal of Superconductivity and Novel Magnetism 2014, 27 (10), 2327-2336.DOI
- [10]Rached, D.; Benkhettou, N.; Soudini, B.; Abbar, B.; Sekkal, N.; Driz, M., Electronic structure calculations of magnesium chalcogenides MgS and MgSe. physica status solidi (B) 2003, 240 (3), 565-573.DOI
- [11]Lee, S.-G.; Chang, K. J., First-principles study of the structural properties of MgS-, MgSe-, ZnS-, and ZnSe-based superlattices. Physical Review B 1995, 52 (3), 1918-1925.pubmed.ncbi.nlm.nih.gov/9981259
- [12]Parker, S. G.; Reinberg, A. R.; Pinnell, J. E.; Holton, W. C., Preparation and Properties of Mg[sub x]Zn[sub 1−x]Te. Journal of The Electrochemical Society 1971, 118 (6), 979.DOI
- [13]Kuhn, A.; Chevy, A.; Naud, M.-J., Preparation and some physical properties of magnesium telluride single crystals. Journal of Crystal Growth 1971, 9, 263-265.DOI
- [14]Duman, S.; Bağcı, S.; Tütüncü, H. M.; Srivastava, G. P., First-principles studies of ground-state and dynamical properties of MgS, MgSe, and MgTe in the rocksalt, zinc blende, wurzite, and nickel arsenide phases. Physical Review B 2006, 73 (20), 205201.DOI
- [15]Gököğlu, G., First principles vibrational dynamics of magnesium telluride. Journal of Physics and Chemistry of Solids 2010, 71 (9), 1388-1392.DOI
- [16]Zhang, F.; Chen, C.; Yao, H.; Bai, F.; Yin, L.; Li, X.; Li, S.; Xue, W.; Wang, Y.; Cao, F.; Liu, X.; Sui, J.; Zhang, Q., High-Performance N-type Mg3Sb2 towards Thermoelectric Application near Room Temperature. Advanced Functional Materials 2020, 30 (5), 1906143.DOI
- [17]Li, J.; Zheng, S.; Fang, T.; Yue, L.; Zhang, S.; Lu, G., Computational prediction of a high zT of n-type Mg3Sb2-based compounds with isotropic thermoelectric conduction performance. Physical Chemistry Chemical Physics 2018, 20 (11), 7686-7693.DOI
- [18]Dmitriev, A. V., High doping effect on the thermoelectric properties of p-type lead telluride. Journal of Applied Physics 2018, 123 (16), 165707.DOI
- [19]Zhang, J.; Song, L.; Pedersen, S. H.; Yin, H.; Hung, L. T.; Iversen, B. B., Discovery of high-performance low-cost n-type Mg3Sb2-based thermoelectric materials with multi-valley conduction bands. Nature Communications 2017, 8 (1), 13901.DOI
- [20]Dughaish, Z. H., Lead telluride as a thermoelectric material for thermoelectric power generation. Physica B: Condensed Matter 2002, 322 (1), 205-223.DOI
- [21]Waag, A.; Heinke, H.; Scholl, S.; Becker, C. R.; Landwehr, G., Growth of MgTe and Cd1−xMgxTe thin films by molecular beam epitaxy. Journal of Crystal Growth 1993, 131 (3), 607-611.DOI
- [22]Tarannum, F.; Muthaiah, R.; Annam, R. S.; Gu, T.; Garg, J., Effect of Alignment on Enhancement of Thermal Conductivity of Polyethylene–Graphene Nanocomposites and Comparison with Effective Medium Theory. Nanomaterials 2020, 10 (7), 1291.DOI
- [23]Muthaiah, R.; Tarannum, F.; Annam, R. S.; Nayal, A. S.; Danayat, S.; Garg, J., Thermal conductivity of hexagonal BC2P – a first-principles study. RSC Advances 2020, 10 (70), 42628-42632.DOI
- [24]Muthaiah, R.; Garg, J., Strain tuned high thermal conductivity in boron phosphide at nanometer length scales – a first-principles study. Physical Chemistry Chemical Physics 2020, 22 (36), 20914-20921.DOI
- [25]Shafique, A.; Shin, Y.-H., Ultrahigh and anisotropic thermal transport in the hybridized monolayer (BC2N) of boron nitride and graphene: a first-principles study. Physical Chemistry Chemical Physics 2019, 21 (31), 17306-17313.DOI
- [26]Muthaiah, R.; Garg, J., Temperature effects in the thermal conductivity of aligned amorphous polyethylene—A molecular dynamics study. Journal of Applied Physics 2018, 124 (10), 105102.DOI
- [27]Lindsay, L.; Broido, D. A.; Reinecke, T. L., First-Principles Determination of Ultrahigh Thermal Conductivity of Boron Arsenide: A Competitor for Diamond? Physical Review Letters 2013, 111 (2), 025901.pubmed.ncbi.nlm.nih.gov/23889420
- [28]Oh, S. K.; Lundh, J. S.; Shervin, S.; Chatterjee, B.; Lee, D. K.; Choi, S.; Kwak, J. S.; Ryou, J.-H., Thermal Management and Characterization of High-Power Wide-Bandgap Semiconductor Electronic and Photonic Devices in Automotive Applications. Journal of Electronic Packaging 2019, 141 (2).DOI
- [29]Thakare, J. G.; Pandey, C.; Mahapatra, M. M.; Mulik, R. S., Thermal Barrier Coatings—A State of the Art Review. Metals and Materials International 2020.DOI
- [30]Clarke, D. R.; Phillpot, S. R., Thermal barrier coating materials. Materials Today 2005, 8 (6), 22-29.DOI
- [31]Padture, N. P.; Gell, M.; Jordan, E. H., Thermal Barrier Coatings for Gas-Turbine Engine Applications. Science 2002, 296 (5566), 280-284.pubmed.ncbi.nlm.nih.gov/11951028
- [32]Basol, B.; McCandless, B., Brief review of cadmium telluride-based photovoltaic technologies. Journal of Photonics for Energy 2014, 4 (1), 040996.DOI
- [33]Saadah, M. In Thermal Management of Solar Cells, 2013.
- [34]Zweibel, K., The Impact of Tellurium Supply on Cadmium Telluride Photovoltaics. Science 2010, 328 (5979), 699-701.DOI
- [35]Giannozzi, P.; Baroni, S.; Bonini, N.; Calandra, M.; Car, R.; Cavazzoni, C.; Ceresoli, D.; Chiarotti, G. L.; Cococcioni, M.; Dabo, I.; Dal Corso, A.; de Gironcoli, S.; Fabris, S.; Fratesi, G.; Gebauer, R.; Gerstmann, U.; Gougoussis, C.; Kokalj, A.; Lazzeri, M.; Martin-Samos, L.; Marzari, N.; Mauri, F.; Mazzarello, R.; Paolini, S.; Pasquarello, A.; Paulatto, L.; Sbraccia, C.; Scandolo, S.; Sclauzero, G.; Seitsonen, A. P.; Smogunov, A.; Umari, P.; Wentzcovitch, R. M., QUANTUM ESPRESSO: a modular and open-source software project for quantum simulations of materials. Journal of Physics: Condensed Matter 2009, 21 (39), 395502.DOI
- [36]Ceperley, D. M.; Alder, B. J., Ground State of the Electron Gas by a Stochastic Method. Physical Review Letters 1980, 45 (7), 566-569.
- [37]Monkhorst, H. J.; Pack, J. D., Special points for Brillouin-zone integrations. Physical Review B 1976, 13 (12), 5188-5192.DOI
- [38]Chakrabarti, A., Role of NiAs phase in pressure-induced structural phase transitions in IIA-VI chalcogenides. Physical Review B 2000, 62 (3), 1806-1814.DOI
- [39]Van Camp, P. E.; Van Doren, V. E.; Martins, J. L., High-pressure phases of magnesium selenide and magnesium telluride. Physical Review B 1997, 55 (2), 775-779.DOI
- [40]Okuyama, H.; Nakano, K.; Miyajima, T.; Akimoto, K., Epitaxial growth of ZnMgSSe on GaAs substrate by molecular beam epitaxy. Journal of Crystal Growth 1992, 117 (1), 139-143.
- [41]Fugallo, G.; Lazzeri, M.; Paulatto, L.; Mauri, F., Ab initio variational approach for evaluating lattice thermal conductivity. Physical Review B 2013, 88 (4), 045430.DOI
- [42]Srivastava, G. P., The physics of phonons. 2019.
- [43]Srivastava, G. P., The Physics of Phonons. Taylor & Francis: 1990.
- [44]Debernardi, A.; Baroni, S.; Molinari, E., Anharmonic Phonon Lifetimes in Semiconductors from Density-Functional Perturbation Theory. Physical Review Letters 1995, 75 (9), 1819-1822.pubmed.ncbi.nlm.nih.gov/10060399
- [45]Deinzer, G.; Birner, G.; Strauch, D., Ab initio calculation of the linewidth of various phonon modes in germanium and silicon. Physical Review B 2003, 67 (14), 144304.DOI
- [46]Paulatto, L.; Errea, I.; Calandra, M.; Mauri, F., First-principles calculations of phonon frequencies, lifetimes, and spectral functions from weak to strong anharmonicity: The example of palladium hydrides. Physical Review B 2015, 91 (5), 054304.DOI
- [47]Paulatto, L.; Mauri, F.; Lazzeri, M., Anharmonic properties from a generalized third-order ab initio approach: Theory and applications to graphite and graphene. Physical Review B 2013, 87 (21), 214303.DOI
- [48]Casimir, H. B. G., Note on the conduction of heat in crystals. Physica 1938, 5 (6), 495-500.DOI
- [49]Coplen, T. B., Atomic Weights of the Elements 1995. Journal of Physical and Chemical Reference Data 1997, 26 (5), 1239-1253.DOI
- [50]Chung, D. H.; Buesssem, W. R., The Voigt-Reuss-Hill (VRH) Approximation and the Elastic Moduli of Polycrystalline ZnO, TiO2 (Rutile), and α-Al2O3. Journal of Applied Physics 1968, 39 (6), 2777-2782.DOI