betaFeedback

WorksPhysics and Astronomy

Surface doping of rubrene single crystals by molecular electron donors and acceptors

Abstract

The surface molecular doping of organic semiconductors can play an important role in the development of organic electronic or optoelectronic devices. Single-crystal rubrene remains a leading molecular candidate for applications in electronics due to its high hole mobility. In parallel, intensive research into the fabrication of flexible organic electronics requires the careful design of functional interfaces to enable optimal device characteristics. To this end, the present work seeks to understand the effect of surface molecular doping on the electronic band structure of rubrene single crystals. Our angle-resolved photoemission measurements reveal that the Fermi level moves in the band gap of rubrene depending on the direction of surface electron-transfer reactions with the molecular dopants, yet the valence band dispersion remains essentially unperturbed. This indicates that surface electron-transfer doping of a molecular single crystal can effectively modify the near-surface charge density, while retaining good charge-carrier mobility.

the molecular dopants, yet the valence band dispersion remains essentially unperturbed. This indicates that surface electron-transfer doping of a molecular single crystal can effectively modify the near-surface charge density, while retaining good charge-carrier mobility.

Introduction

Electrical doping in organic semiconductors involves the transfer of electrons between a dopant and the host semiconductor for generating free charge carriers within the host material. The addition of electrons or holes to the semiconductor is accompanied by an energy shift of the Fermi level (electrochemical potential of electrons) relative to the valence and conduction band edges. Manipulating the free charge-carrier concentration, and thus the Fermi level, presents a key strategy for modifying and enhancing the electrical properties of organic semiconductors. Previous efforts employing atomic dopants such as halogens or alkali metals resulted mainly in unstable devices due to the high diffusivity, chemical reactivity, and poor air stability of such dopants [1, 2, 3, 4, 5]. In contrast, molecular dopants can be superior doping agents for organic semiconductors due to a number of factors. For instance, their larger size compared to atomic dopants reduces the Coulombic interactions with the contributed charge carriers and the chance of diffusion into the semiconductor’s bulk. Also, their moderate sublimation temperature is beneficial for processing and device integrity during fabrication [6, 7, 8, 9, 10, 11].

In parallel with the development of tailored, more efficient dopants, the field of organic semiconductors has advanced noticeably. New classes of thienoacene and pyrene-based organic semiconductors with field-effect charge-carrier mobilities as high as 30 cm2V−1s−130\ \mathrm{cm}^{2}\mathrm{V}^{-1}\mathrm{s}^{-1} were introduced, paving the way for sustainable flexible electronic devices [12, 13, 14]. However, the ideal performance of organic electronic devices is severely impacted by high contact resistances and charge-carrier trapping. Several studies indicated that doping can effectively circumvent both obstacles. For example, adding a thin layer of dopants between the metal contact and the semiconductor can effectively reduce the charge injection barriers [15, 16, 17]. Passivation of trap states, which can improve the transport characteristics by lowering the threshold voltage, is a further benefit of doping [18, 19, 20, 21]. Also, low to moderate doping of the channel can be beneficial as long as the conductivity does not increase at the cost of a decreased current on/off ratio [22]. A previous work by Lüssem et al. demonstrated successful doping of pentacene thin films by evaporating thin layers of n-type and p-type dopants, making depletion and inversion operation modes possible [23]. Other works have also reported the change in the field-effect transistor polarity after doping with molecular electron donors and acceptors [24, 25, 26].

Here, we investigate the surface doping of rubrene single crystals, a benchmark organic semiconductor. As illustrated in Figure 1a and Figure 1b, rubrene has a distinct chemical structure and an orthorhombic single-crystalline structure (space group Cmca) [27]. Notably, these characteristics facilitate a high hole mobility along the bb-axis of its crystal lattice. In fact, previous measurements on rubrene single-crystal field-effect transistors indicate hole mobility values up to 40 cm2V−1s−140\ \mathrm{cm}^{2}\mathrm{V}^{-1}\mathrm{s}^{-1} [28, 29]. Furthermore, large arrays of high-performance rubrene single-crystal field-effect transistors with mobilities as high as 2.4 cm2V−1s−12.4\ \mathrm{cm}^{2}\mathrm{V}^{-1}\mathrm{s}^{-1} and large on/off ratios on the order of 10710^{7}, have been fabricated on flexible substrates [30]. For these reasons, rubrene is one of the most relevant technological candidates for organic electronics. The superior electronic properties of rubrene, relative to other molecular semiconductors, are mainly attributed to the formation of a dispersive valence band along the b∗b^{*} reciprocal lattice vector, shown in Figure 1c. Indeed, density-functional theory calculations indicate a highly dispersive valence band with a bandwidth of 0.40.4 eV along the Γ\Gamma–Υ\Upsilon path in the Brillouin zone [31, 32]. This implies a considerable wavefunction overlap among adjacent rubrene molecules along bb-axis in real space. In line with this, previous angle-resolved photoemission investigations have observed the valence band dispersion of rubrene [33, 34, 35, 36]. Consequently, it is expected that charge transport in rubrene single crystal is essentially mediated by delocalized holes [37]. The current challenge is to control the electronic bands of rubrene through doping without disrupting the single-crystal structure and thus impeding carrier transport.

Molecular structure of rubrene, primitive unit cell of orthorhombic rubrene, and first Brillouin zone

Figure 1. Molecular structure of rubrene (left). Primitive unit cell of the orthorhombic rubrene single crystal (Cmca) (middle). The first Brillouin zone of the reciprocal lattice of rubrene (right). As indicated by the color, each direct lattice vector corresponds to a reciprocal lattice vector. Each direct lattice vector in orthorhombic crystals is parallel to its corresponding reciprocal lattice vector. In the reciprocal space, a dispersive valence band appears along the b∗b^{*} direction due to the strong wavefunction overlap between the HOMO orbitals along the bb crystallographic direction in real space. The Γ\Gamma, Υ\Upsilon and X\Chi correspond to high symmetry points of the Brillouin zone.

For this purpose, surface molecular doping can be a more effective strategy than bulk doping. As the electronic properties of organic single crystals ultimately depend on their crystal structure, it is anticipated that bulk doping might have a negative impact. In fact, Hall measurements in bulk-doped rubrene single crystals reported previously by Ohashi et al. show decreased Hall mobility. This was attributed to the lattice defects generated by doping that can act as scattering sites, thus reducing the mean free path of the mobile holes [38]. In contrast, introducing a uniform layer of dopants to the surface of rubrene single crystals should not be destructive and could, in principle, alter the near-surface intrinsic electronic character to p-type or n-type.

In this work, we deposited thin layers of two bulky molecular dopants on rubrene single crystals by thermal evaporation in ultrahigh vacuum. One dopant, Mo(tfd−CO2Me)3\mathrm{Mo(tfd-CO_{2}Me)_{3}}, whose chemical structure is shown in Figure 2a, has a high electron affinity of 5.0 eV, measured previously by inverse photoemission spectroscopy [39]. As shown schematically in the energy level diagram of Figure 2c, because the solid-state ionization energy of rubrene almost lies at the same energy, electron transfer is expected to occur from the valence band of rubrene to the lowest unoccupied molecular orbital (LUMO) level of Mo(tfd−CO2Me)3\mathrm{Mo(tfd-CO_{2}Me)_{3}}. The electron depletion at the surface of rubrene should push the Fermi level towards the valence band, giving the surface a p-type character. Conversely, when an electron-donating molecule is used, the opposite is anticipated. As an electron donor we used cobaltocene (CoCp2\mathrm{CoCp_{2}}), whose chemical structure is shown in Figure 2b. Cobaltocene has a low solid-state ionization energy of 4.1 eV, reported previously [40]. This can trigger an electron transfer from the singly occupied molecular orbital (SOMO) level of CoCp2\mathrm{CoCp_{2}} to the conduction band of rubrene. The higher electron concentration at the surface of rubrene would move its Fermi level towards the conduction band, resulting in an n-type conductivity behavior.

Chemical structures of Mo(tfd-CO$_2$Me)$_3$ and CoCp$_2$ molecules and electronic energy levels

Figure 2. Chemical structures of Mo(tfd-CO2_2Me)3_3 (a) and CoCp2_2 (b) molecules. The electronic energy levels for the LUMO and SOMO of the p-dopant and n-dopant, respectively, are shown with respect to the vacuum level (c). In the case rubrene single crystal wider boxes are used to represent the valence (VB) and conduction bands (CB). The valence band maximum is measured in this work and found to be 5.0 eV. The energy of the conduction band minimum is tentatively positioned approximately 2.8 eV lower, taking into account the band gap previously measured in rubrene thin films by inverse photoemission spectroscopy [57]. This placement provides only a rough representation as it applies data from thin films to our current study on single crystals.

To test the hypotheses, we performed angle-resolved photoemission spectroscopy (ARPES) measurements on bare and surface-doped rubrene single crystals with the above-mentioned molecular electron donors and acceptors. ARPES allows direct observation of the electronic bands, and we could directly disclose the effect of surface doping on the valence band of rubrene. Our results underpin this non-destructive doping approach, in which the dopants are adsorbed on the surface of rubrene without disrupting its single-crystalline structure.

Experiment

Rubrene single crystals were grown via horizontal physical vapor transport [41, 42]. For this purpose, a steep temperature gradient is applied across a fused silica glass tube which is located in a furnace. Simultaneously, a 30 sccm N2N_{2} (6 N purity) inert gas flow is applied. On the hot side of the furnace, the starting material, ca. 105 mg of purified rubrene powder, is placed and sublimed at 335 °C over 48 h. The sublimed material is transported along the temperature gradient to the cold side, where it recrystallizes, yielding plate-like single crystals with a lateral extension of up to 5 mm. The as-grown crystals were slowly cooled down over 8 h to minimize thermal stress.

Prior to the photoemission experiments, the rubrene single crystals were attached to copper substrates using silver paste to allow sample grounding. Photoemission experiments were performed at the LowDosePES end-station of the BESSY II PM4 beamline of the Helmholtz Zentrum Berlin für Materialien und Energie GmbH (HZB). PM4 is equipped with an angle-resolved time-of-flight (ArTOF) spectrometer that collects the emitted electrons at a broad solid angle of up to 30°. The pulsed excitation source required by the ArTOF analyzers is suitable for investigating radiation sensitive samples such as organics [43]. All experiments were conducted at ambient temperature and in ultrahigh vacuum (10−910^{-9} mbar). The excitation energy was set to 35 eV corresponding to a short photoelectron mean free path (5-10 Å), for which only electrons from rubrene’s uppermost layers contribute to the signal. The experimental setup provides a 20 meV energy resolution and a 0.09° angular resolution.

We measured two rubrene single-crystal samples, the electronic band structures of which were essentially identical (Figure S1, supporting information). A minor discrepancy of approximately 50 meV in the binding energy position of the valence peaks between the two samples can be observed by the results of the quantitative analysis on the valence peaks (Table S1, supporting information). This discrepancy could potentially be attributed to the inherent uncertainty associated with the measurements of samples of varying thicknesses, or to minute variations in crystal growth conditions within the same or different production batches. During the measurement, consecutive energy-distribution curves (EDCs) recorded over equal time durations revealed the impact of sample charging: broadening and shifting of the HOMO peak towards higher binding energy. In photoemission from materials having low conductivity, such as organics, the buildup of a positive surface charge due to the removal of electrons is typically a hurdle for the accurate interpretation of photoemission spectra. But it can usually be compensated by taking advantage of their photoconductivity induced by an external source of light [44]. In our case, we used a continuous wave laser of 473 nm wavelength to constantly illuminate the sample. To neutralize the radiation induced charging, a nominal laser power density of 0.3 mW/cm2\mathrm{mW}/\mathrm{cm}^{2} was required. (Figure S2, supporting information).

Four 2D spectra panels labelled a–d, showing binding energy versus $k_{\parallel}$

Figure S1. 2D spectra of the two bare rubrene single crystal samples measured prior to the surface doping. (a), (b) 2D spectra of the first single crystal rubrene sample along the Γ\Gamma-Y and Γ\Gamma-X directions, respectively. (c), (d) 2D spectra of the second single crystal rubrene sample along the Γ\Gamma-Y and Γ\Gamma-X directions, respectively. The 2D spectra of the two single crystal rubrene samples show strong qualitative agreement.

Influence of surface charging and its compensation using an external source of light

Figure S2. Influence of surface charging and its compensation using an external source of light (continuous wave blue laser of 473 nm and with 5 mW max output power). (a) In the absence of laser, consecutive EDCs of equal time durations revealed that the HOMO peak became broader and drifted towards higher binding energies, indicating strong effects of surface charging. By illuminating the sample with a blue laser we could compensate the effect of charging (b). The progressive increase of the laser output power shifts the HOMO peak of rubrene back to lower binding energies. With laser power greater than 40 percent, the position and the shape of the peak stabilized. Given that the diameter of the defocused laser beam is approximately 16 mm, 60 percent of laser power corresponds to a nominal power density of 0.3 mW/cm2cm^{2}.

EH1E_{\mathrm{H1}} (eV)FWHMH1\mathrm{FWHM}_{\mathrm{H1}} (eV)EAE_{\mathrm{A}} (eV)FWHMA\mathrm{FWHM}_{\mathrm{A}} (eV)
bare rubrene0.64±0.010.64 \pm0.010.21±0.040.21 \pm0.040.94±0.020.94 \pm0.020.42±0.080.42 \pm0.08
p-doped0.56±0.010.56 \pm0.010.24±0.050.24 \pm0.050.86±0.020.86 \pm0.020.42±0.090.42 \pm0.09
bare rubrene0.69±0.010.69 \pm0.010.21±0.050.21 \pm0.050.97±0.020.97 \pm0.020.43±0.080.43 \pm0.08
n-doped0.83±0.010.83 \pm0.010.21±0.050.21 \pm0.051.12±0.021.12 \pm0.020.44±0.080.44 \pm0.08

Table S1. Least-square fitting parameters of Figure S4. EH1E_{\mathrm{H1}} is the energy position of the dispersive H1 peak, EAE_{\mathrm{A}} the energy position of the satellite A feature, FWHMH1\mathrm{FWHM}_{\mathrm{H1}} and FWHMA\mathrm{FWHM}_{\mathrm{A}} the full width at half maximum of the peak H1 and A, respectively.

Surface doping was achieved in-situ by thermally evaporating the molecular dopants on bare rubrene single crystals. p-Doping was achieved by depositing a thin layer of Mo(tfd−CO2Me)3\mathrm{Mo(tfd-CO_{2}Me)_{3}} at a constant evaporation rate of 0.1 A˚/s\mathrm{\AA}/\mathrm{s}, as measured by a quartz crystal microbalance. The final nominal thickness of the molecular layer was 1.5 nm. In the case of the n-doping with CoCp2\mathrm{CoCp_{2}} the film thickness could not be determined due to the high volatility of CoCp2\mathrm{CoCp_{2}}. Instead, we observed Instead, we monitored the changes in rubrene’s valence band structure throughout three successive evaporations, each of an increasing duration.

Results and Discussion

Band structure of the bare rubrene single crystal

In Figure 3a-Figure 3d, we show the angle-resolved EDCs and the corresponding 2D spectra of bare rubrene along the Γ\Gamma-Y\mathrm{Y} and Γ\Gamma-X\mathrm{X} directions of the Brillouin zone, respectively. Along the Γ\Gamma-X\mathrm{X} direction, Figure 3b and Figure 3d, there is no clear indication of dispersive features in the valence region. In the Γ\Gamma-Y\mathrm{Y} direction, Figure 3a and Figure 3c, there is a visible dispersive peak (H1\mathrm{H}_{1}), which can be associated with the HOMO derived valence band of rubrene single crystals, as demonstrated in earlier experimental and theoretical studies [31, 32, 33, 34]. The maximum of the valence band is at the Γ\Gamma point, 0.64 eV below the Fermi level, determined by the peak maximum of H1\mathrm{H}_{1} at the Γ\Gamma point. Notably, the Γ\Gamma-Υ\Upsilon direction shows two additional features, A and B, which appear at fixed binding energy positions below the band maximum and have also been observed in prior ARPES measurements [33, 34, 45]. Previous studies, both theoretical and experimental, demonstrate the occurrence of a second dispersive band along the Γ\Gamma-Υ\Upsilon direction due to the presence of two inequivalent molecules in the unit cell [27, 32, 33]. This can explain the A feature below H1\mathrm{H}_{1}. A peak analysis of the EDC at the Γ\Gamma point revealed that the energy separation between H1\mathrm{H}_{1} and A is roughly 0.3 eV (Figure S3 and Table S1, supporting information). The observed energy separation does not fully match the theoretical value of 0.20 eV, although such a difference is expected when density-functional theory fails to capture the correct many-body correlation effects of the excited system. In fact, it has been demonstrated before for pentacene that molecular vibration and the presence of disorder can explain the greater separation between the two HOMO-derived bands [46].

Angle-resolved EDCs along Γ–Y and Γ–X directions, with corresponding 2D spectra

Figure 3. Angle-resolved EDCs along Γ–Y (a), and Γ–X (b) directions of the Brillouin zone. The short blue lines indicate the peak position of the dispersive H1 peak and the yellow and red lines show the non-dispersive A and B satellite features of the spectrum. The respective 2D spectra of the Γ–Y (c) and Γ–X (d) show valence band of rubrene. The black dashed lines indicate the positions of the Γ, Y and X high symmetry points which are also the boundaries of the Brillouin zone (BZ).

Quantitative analysis of the HOMO peak at the $\Gamma$ point of bare and surface-doped rubrene

Figure S3. Quantitative analysis of the HOMO peak at the Γ\Gamma point of bare and surface-doped rubrene. The total HOMO peak was deconvoluted using two Voigt functions to account for the dispersive H1_1 peak and the satellite feature A. Voigt functions are preferred for fitting photoelectron peaks, as they are convolutions of Gaussian and Lorentzian profiles that represent the instrumental broadening and the natural broadening due to the lifetime of the photoexcited state, respectively. The empty circles indicate the raw data points, the blue Voigt function represents the H1_1 peak, whereas the purple is associated to the A satellite peak. The yellow dashed background corresponds to the Shirley background. The red curves represent the total least-squares fitting curve of the valence peak. The black vertical dashed lines depict the positions of the H1_1 peaks before and after doping. The fitting parameters are listed in Table S1. For Mo(tfd-CO2_2Me)3_3 (p-doping), the H1_1 peak shows a shift of 80 meV towards lower binding energies (a). In the case of CoCp2_2 (n-doping), the H1_1 peak shifts by 140 meV towards higher binding energies (b). The intensity from the HOMO peak of rubrene is attenuated due to the deposition of the molecular dopant layers on the surface.

Additionally, the origin of feature B, unexplained by previous density-functional theory calculations of the band structure of rubrene, may be attributed to scattering processes during photoemission. These could be a result of both thermal disorder and structural disorder on the surface, possibly induced by the prior exposure of the crystals to ambient conditions [47]. For example, scattering by vibrations and impurities can spread the discrete electron states over a range of energies and momenta giving rise to an incoherent background component to the photoemission spectrum [48]. According to Ciuchi et al., photoelectrons can be scattered at room temperature by the intramolecular vibrations of rubrene, resulting in broadened spectral linewidths [49]. The B feature, appearing as a kk-independent uniform background contributing to the broadening of the H1\mathrm{H}_{1} peak, can be considered the incoherent component of the total kk-resolved spectral intensity. Previous photoemission studies have demonstrated that, in the presence of dynamic disorder, the total kk-resolved photoelectron spectrum (Itot(k,E)I_{\mathrm{tot}}(k,E)) can be described as the sum of a coherent spectrum associated with direct electronic transitions (Icoh(k,E)I_{\mathrm{coh}}(k,E)), and an incoherent background (Iincoh(k,E)I_{\mathrm{incoh}}(k,E)):

Itot(k,E)=W⋅Icoh(k,E)+Iincoh(k,E)(1)I_{\mathrm{tot}}(k,E) = W \cdot I_{\mathrm{coh}}(k,E) + I_{\mathrm{incoh}}(k,E) \tag*{(1)}

Here, WW represents the Debye-Waller factor [50, 51] [49, 50]. Despite not knowing the Debye-Waller factor it is still possible to approximate the coherent part of the spectrum associated with rubrene’s intrinsic valence band by subtracting a reasonable incoherent background.

In such cases, the incoherent background resembles the kk-integrated density of states [51, 52]. Thus, subtracting the experimental kk-integrated EDC as a background from every kk-resolved EDC simplifies the quantitative analysis for determining the intrinsic band parameters (Figure S4 and Figure S5 supporting information). The band parameters can be determined by approximating the HOMO-derived valence band with the energy dispersion relation of the one-dimensional tight-binding model:

Background subtraction procedure applied to the EDC at the $\Gamma$ point

Figure S4. Background subtraction procedure applied to the EDC at the Γ\Gamma point. The exact methodology for subtracting the background from the 2D spectra can be clearly depicted in the figure above. The green curve represents the kk-resolved EDC, the black curve corresponds to the kk-integrated spectrum that has been normalized relative to the satellite feature’s intensity. The blue dotted line represents the spectrum remaining after subtraction of the kk-resolved EDC and the kk-integrated spectrum. The red line corresponds to the Gaussian fit of the residual spectrum, from which the energy position of the dispersive H1_1 peak is determined.

Background subtraction applied to the 2D spectra

Figure S5. Background subtraction applied to the 2D spectra. By using the background subtraction approach illustrated in Figure S5 to all kk-resolved EDCs, we were able to eliminate the contribution of the AA and BB satellites attributed to scattering processes due to the dynamic disorder at room temperature. Specifically, (a) shows the total 2D spectrum of bare rubrene and (b) displays the spectrum remaining after background subtraction. Using a batch fitting script implemented in Igor Pro 9, each residual kk-resolved profile, was fitted by one Gaussian peak to determine the energy position of the H1_1 peak. (c) shows the extracted (E,k)(E,k) data points corresponding to the H1_1 dispersive peak.

EB(k)=EC+2t⋅cos⁡(ak)(2)E_{\mathrm{B}}(k) = E_{\mathrm{C}} + 2t \cdot\cos(ak) \tag*{(2)}

where EBE_{\mathrm{B}} is the electron’s binding energy, kk the electron’s momentum, ECE_{\mathrm{C}} the energy of the center of the valence band, tt the transfer integral, and aa the lattice constant. Moreover, the hole effective mass at the Γ\Gamma point, mTB∗m_{\mathrm{TB}}^{*}, is given by:

mTB∗=−ℏ22ta2(3)m_{\mathrm{TB}}^{*} = -\frac{\hbar^{2}}{2ta^{2}} \tag*{(3)}

The above relations are used for the analysis of band structure properties further below.

Surface molecular doping

The 2D intensity maps of bare and surface-doped rubrene are depicted in Figure 4a-Figure 4d. In the case of Mo(tfd-CO2Me)3\mathrm{Mo(tfd\text{-}CO_{2}Me)_{3}}, the deposited layer of molecular acceptors shifted the valence band of rubrene 90 meV toward the Fermi level, as seen in Figure 4a and Figure 4b. In contrast, the molecular donor CoCp2\mathrm{CoCp_{2}} induced a 140 meV shift of the valence band in the opposite direction, as shown in Figure 4c and Figure 4d. In either case, the shift of the valence band can be attributed to electron-transfer reactions at the interface between the dopants and rubrene. In particular, the deposited layer of molecular acceptors triggers an electron transfer from the highest occupied valence states of rubrene close to the interface to the LUMO of Mo(tfd-CO2Me)3\mathrm{Mo(tfd\text{-}CO_{2}Me)_{3}} in order to achieve electronic equilibrium. The redistribution of charges (i.e., space-charge accumulation) generates an electric field close to the interface, which bends the valence band upwards and is associated with an increased concentration of holes at the surface of rubrene. Conversely, the deposition of donor molecules causes an electron transfer from the SOMO of CoCp2\mathrm{CoCp_{2}} to the lowest unoccupied states of rubrene. The increased concentration of electrons at the surface of rubrene induced a downward bending of the valence band. In addition, we observed that the valence band along the Γ\Gamma-X\mathrm{X} direction exhibited similar shifts due to surface doping (as shown in Figure S6 of the supporting information). This observation suggests that the doping process likely induced a uniform charge distribution on the surface, leading to a concurrent shift in all electronic states.

2D spectra of bare rubrene, p-doped rubrene, and n-doped rubrene

Figure 4. Figure 4 2D spectra of the bare (undoped) rubrene (a), (c), surface p-doped rubrene (b) and surface n-doped rubrene. The red curve represents the least-square fit of the valence band approximated by the 1D tight binding dispersion relation.

Band bending of the valence band of rubrene along the $\Gamma$-$\mathrm{X}$ directions due to surface molecular doping

Figure S6. Band bending of the valence band of rubrene along the Γ\Gamma-X\mathrm{X} directions due to the surface molecular doping. As mentioned in the main text for the case of the valence band along the Γ\Gamma-Y\mathrm{Y} direction, the charge redistribution at the interface induced by doping results in the bending of all electronic states, including the valence band along the Γ\Gamma-X\mathrm{X} direction. In particular, p-doping with \mathrm{Mo(tfd\mathchar`-CO_{2}Me)_{3}} shifts the valence band towards the Fermi level, (a) to (b). Similarly, when rubrene is n-doped with CoCp2\mathrm{CoCp_{2}} the valence band shifts away from the Fermi level (c) to (d).

Assuming that the induced charge carriers at the band edges behave as free particles and that they obey Boltzmann statistics we can roughly estimate the induced concentration of holes by the following expression:

pfpi=exp⁡[−ΔEVkbT](4)\frac{p_f}{p_i}=\exp\left[-\frac{\Delta E_V}{k_bT}\right] \tag*{(4)}

where pip_i is the initial concentration of holes for the undoped rubrene, pfp_f the final concentration of holes after surface doping and ΔEV\Delta E_V the energy shift of the valence band [53]. Given that at room temperature the thermal energy is kbT=25k_bT = 25 meV, then the valence-band energy shifts of -90 meV and 140 meV could effectively modulate the hole concentration at the surface by up to two orders of magnitude. Most importantly, it appears that the surface molecular doping had no apparent effect on the shape of the rubrene valence band. A quantitative analysis, the results of which are listed in Table 1, revealed that the band parameters, transfer integral, and hole effective mass, remain essentially constant. Therefore, it is reasonable to assume that the deposition of Mo(tfd-CO2Me)3\mathrm{Mo}(\mathrm{tfd\text{-}CO_2Me})_3 and CoCp2\mathrm{CoCp}_2, and the induced charge concentrations, do not result in structural deformation of the surface lattice of rubrene nor in anisotropic charge-carrier distribution along certain directions.

ECE_C (eV)ΔEC\Delta E_C (meV)aa (Å)tt (meV)∣mTB∗∣|m^*_{\mathrm{TB}}| (m0m_0)
bare rubrene0.88 ± 0.01-6.8 ± 0.1103 ± 100.8 ± 0.1
p-doped0.79 ± 0.01-90 ± 106.8 ± 0.1100 ± 100.8 ± 0.1
bare rubrene0.93 ± 0.01-6.9 ± 0.1105 ± 100.7 ± 0.1
n-doped1.07 ± 0.01140 ± 106.9 ± 0.1101 ± 100.8 ± 0.1

Table 1. Band parameters of 1D-tight binding approximation where (ECE_C) the center of the valence band, (ΔEC\Delta E_C) the shift of the valence band center after doping, (aa) lattice parameter corresponding to bb crystallographic axis of rubrene single crystal, (tt) transfer integral and (mTB∗m^*_{\mathrm{TB}}) hole effective mass.

The magnitude of the valence band shifts, related to doping efficiency, is noteworthy, as it does not appear to be strictly determined by the energy offsets between the frontier energy levels of rubrene and the dopants. One might expect larger changes, even for such small energy differences.

Several distinct and interrelated factors may explain this situation. First, the small shift in the case of the p-dopant could be related to the low dopant concentration on the surface, as indicated by the small signals observed in the X-ray photoemission spectra (Figure S7, supporting information). Second, materials inherently contain native defects, the origin, concentration, and spatial distribution of which largely depend on the crystal growth conditions and the post-treatment of the crystals after growth. These native defects can generate an intra-bandgap density of states, acting as electron donors or acceptors, and consequently, compensating for further doping of the surface. In this scenario, the Fermi level becomes pinned by the defect states, causing the valence band to be fixed at a certain position, irrespective of the dopant concentrations [54, 55]. Lastly, intermolecular interactions at the interface can significantly modify the energetics of the donating and accepting energy levels, leading to unfavorable energy barriers that impede charge-carrier hopping across the interface [56].

Additional ultraviolet and X-ray photoemission spectra showing UPS valence and secondary electron cut-off regions, and XPS sulfur and fluorine core-level signals

Figure S7. Additional ultraviolet (UPS) and X-ray (XPS) photoemission spectra. This figure provides further support to the surface doping of bare rubrene with the molecular acceptor Mo(tfd−CO2Me)3\mathrm{Mo(tfd-CO_2Me)_3}. Additional UPS and XPS measurements were performed on a standard setup with a He discharge lamp (He-I 21.22 eV) and a hemispherical analyzer (Specs, PHOIBOS 100). The valence region of rubrene (a), was obtained at the Γ\Gamma point before and after the evaporation of 1.5 nm Mo(tfd−CO2Me)3\mathrm{Mo(tfd-CO_2Me)_3}. In agreement to what we found in our ArTOF measurements, the evaporation of the dopants induced a shift of the valence peak by approximately 80 meV, as determined by a linear extrapolation of the HOMO peak onsets. After doping the spectrum becomes less structured with the valence peak hidden in the background intensity. This is expected as the dopant adlayer can prevent the electrons from the covered rubrene’s surface from being phootemitted. The UPS valence region was recorded with pass energy 10 eV that allows energy resolution of 120 meV. (b) shows the secondary electron cut-off region (SECO). The SECO was obtained using -10 V bias voltage and pass energy 2 eV allowing an energy resolution of 60 meV. The work function can be determined by a linear extrapolation of the onset of the SECO. P-doping increases the work function by roughly 0.1 eV. The shift of the work function is consistent with the band bending of the valence band (80 meV). (c) and (d) show the XPS signals of Sulfur’s 2p and Fluorine’s 1s core levels, which are present in Mo(tfd−CO2Me)3\mathrm{Mo(tfd-CO_2Me)_3}.

Conclusions

In conclusion, our photoemission results demonstrate that surface doping by thermal evaporation of molecular thin layers can indeed change the intrinsic electronic character of rubrene single crystal surfaces to more n-type or p-type. This is attributed to the observed shifts of the rubrene valence band relative to the Fermi level. Importantly, the doping is accomplished without disrupting the surface structure of single-crystal rubrene, a prerequisite to preserving the HOMO-derived valence band. A next step could be charge-transport measurements to test how the surface molecular doping of rubrene single crystals affects device characteristics. Furthermore, in order to comprehend the magnitude of the observed shifts and identify specific routes for the efficient doping of organic semiconductors it is necessary to fully understand the reasons that may limit the surface molecular doping of rubrene. This could involve the use of different molecular dopants and a systematic investigation of both the microscopic interactions between the semiconductor host and the dopants as well as the potential thermodynamic limitations of doping organic semiconductors containing native defects. These points should form the basis of our future studies.

Acknowledgments

We gratefully acknowledge the beamline scientists of PM4 end-station Dr. Erika Giangrisostomi and Dr. Ruslan Ovsyannicov for their kind support in the course of the ArTOF experiments. We also thank Dr. Patrick Amsalem and Dr. Ross Warren for the insightful discussions. This project has received funding from the DFG project 239543752 and the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No 811284 (UHMOB). S.H. and J.P. acknowledge financial support by the Bavarian State Ministry of Science, Research, and the Arts (Collaborative Research Network ‘Solar Technologies Go Hybrid’). Y.Z., S.B., and S.R.M. thank the National Science Foundation for support through the DMREF program (DMR-1729737).

Supporting information

References

  1. [1]Y. Yamamoto, K. Yoshino, Y. Inuishi, Electrical Properties of Phthalocyanine-Halogen Complexes, J Physical Soc Japan. 47 (1979) 1887–1891. https://doi.org/10.1143/JPSJ.47.1887.
  2. [2]T. Minakata, I. Nagoya, M. Ozaki, Highly ordered and conducting thin film of pentacene doped with iodine vapor, J Appl Phys. 69 (1991) 7354–7356. https://doi.org/10.1063/1.347594.
  3. [3]A. Ali Benamara, M. Galtier, A. Montaner, N doping of polyacetylene, Synth Met. 41 (1991) 45–48. https://doi.org/10.1016/0379-6779(91)90993-F.
  4. [4]G. Parthasarathy, C. Shen, A. Kahn, S.R. Forrest, Lithium doping of semiconducting organic charge transport materials, J Appl Phys. 89 (2001) 4986–4992. https://doi.org/10.1063/1.1359161.
  5. [5]R. Di Pietro, H. Sirringhaus, High resolution optical spectroscopy of air-induced electrical instabilities in n-type polymer semiconductors, Advanced Materials. 24 (2012) 3367–3372. https://doi.org/10.1002/adma.201200829.
  6. [6]J.H. Oh, P. Wei, Z. Bao, Molecular n-type doping for air-stable electron transport in vacuum-processed n-channel organic transistors, Appl Phys Lett. 97 (2010) 243305. https://doi.org/10.1063/1.3527972.
  7. [7]C. Murawski, C. Fuchs, S. Hofmann, K. Leo, M.C. Gather, Alternative p-doped hole transport material for low operating voltage and high efficiency organic light-emitting diodes, Appl Phys Lett. 105 (2014) 113303. https://doi.org/10.1063/1.4896127.
  8. [8]B. Lüssem, M. Riede, K. Leo, Doping of organic semiconductors, Physica Status Solidi (A) Applications and Materials Science. 210 (2013) 9–43. https://doi.org/10.1002/pssa.201228310.
  9. [9]I. Salzmann, G. Heimel, Toward a comprehensive understanding of molecular doping organic semiconductors (review), J Electron Spectros Relat Phenomena. 204 (2015) 208–222. https://doi.org/10.1016/j.elspec.2015.05.001.
  10. [10]I. Salzmann, G. Heimel, M. Oehzelt, S. Winkler, N. Koch, Molecular Electrical Doping of Organic Semiconductors: Fundamental Mechanisms and Emerging Dopant Design Rules, Acc Chem Res. 49 (2016) 370–378. https://doi.org/10.1021/acs.accounts.5b00438.
  11. [11]I.E. Jacobs, A.J. Moulé, Controlling Molecular Doping in Organic Semiconductors, Advanced Materials. 29 (2017) 1703063. https://doi.org/10.1002/adma.201703063.
  12. [12]M.J. Kang, I. Doi, H. Mori, E. Miyazaki, K. Takimiya, M. Ikeda, H. Kuwabara, Alkylated dinaphtho[2,3-b:2′,3′-f]thieno[3,2-b]thiophenes (Cn-DNTTs): Organic semiconductors for high-performance thin-film transistors, Advanced Materials. 23 (2011) 1222–1225. https://doi.org/10.1002/adma.201001283.
  13. [13]T. Yamamoto, K. Takimiya, Facile synthesis of highly π-extended heteroarenes, dinaphtho[2,3-b: 2′,3′-f]chalcogenopheno[3,2-b]chalcogenophenes, and their application to field-effect transistors, J Am Chem Soc. 129 (2007) 2224–2225. https://doi.org/10.1021/ja068429z.
  14. [14]K. Takimiya, K. Bulgarevich, M. Abbas, S. Horiuchi, T. Ogaki, K. Kawabata, A. Ablat, “Manipulation” of Crystal Structure by Methylthiolation Enabling Ultrahigh Mobility in a Pyrene-Based Molecular Semiconductor, Advanced Materials. 33 (2021) 2102914. https://doi.org/10.1002/adma.202102914.
  15. [15]A.A. Günther, M. Sawatzki, P. Formánek, D. Kasemann, K. Leo, Contact Doping for Vertical Organic Field-Effect Transistors, Adv Funct Mater. 26 (2016) 768–775. https://doi.org/10.1002/adfm.201504377.
  16. [16]T. Minari, P. Darmawan, C. Liu, Y. Li, Y. Xu, K. Tsukagoshi, Highly enhanced charge injection in thienoacene-based organic field-effect transistors with chemically doped contact, Appl Phys Lett. 100 (2012) 093303. https://doi.org/10.1063/1.3690949.
  17. [17]S. Singh, S.K. Mohapatra, A. Sharma, C. Fuentes-Hernandez, S. Barlow, S.R. Marder, B. Kippelen, Reduction of contact resistance by selective contact doping in fullerene n-channel organic field-effect transistors, Appl Phys Lett. 102 (2013) 153303. https://doi.org/10.1063/1.4802237.
  18. [18]S. Olthof, S. Mehraeen, S.K. Mohapatra, S. Barlow, V. Coropceanu, J.L. Brédas, S.R. Marder, A. Kahn, Ultralow doping in organic semiconductors: Evidence of trap filling, Phys Rev Lett. 109 (2012). https://doi.org/10.1103/PhysRevLett.109.176601.
  19. [19]J. Soeda, Y. Hirose, M. Yamagishi, A. Nakao, T. Uemura, K. Nakayama, M. Uno, Y. Nakazawa, K. Takimiya, J. Takeya, Solution-crystallized organic field-effect transistors with charge-acceptor layers: High-mobility and low-threshold-voltage operation in air, Advanced Materials. 23 (2011) 3309–3314. https://doi.org/10.1002/adma.201101027.
  20. [20]P. Wei, J.H. Oh, G. Dong, Z. Bao, Use of a 1 H -benzoimidazole derivative as an n -type dopant and to enable air-stable solution-processed n -channel organic thin-film transistors, J Am Chem Soc. 132 (2010) 8852–8853. https://doi.org/10.1021/ja103173m.
  21. [21]M.P. Hein, A.A. Zakhidov, B. Lüssem, J. Jankowski, M.L. Tietze, M.K. Riede, K. Leo, Molecular doping for control of gate bias stress in organic thin film transistors, Appl Phys Lett. 104 (2014) 013507. https://doi.org/10.1063/1.4861168.
  22. [22]Y. Abe, T. Hasegawa, Y. Takahashi, T. Yamada, Y. Tokura, Control of threshold voltage in pentacene thin-film transistors using carrier doping at the charge-transfer interface with organic acceptors, Appl Phys Lett. 87 (2005) 1–3. https://doi.org/10.1063/1.2099540.
  23. [23]B. Lüssem, M.L. Tietze, H. Kleemann, C. Hoßbach, J.W. Bartha, A. Zakhidov, K. Leo, Doped organic transistors operating in the inversion and depletion regime, Nat Commun. 4 (2013) 1–6. https://doi.org/10.1038/ncomms3775.
  24. [24]D. Khim, K.J. Baeg, M. Caironi, C. Liu, Y. Xu, D.Y. Kim, Y.Y. Noh, Control of ambipolar and unipolar transport in organic transistors by selective inkjet-printed chemical doping for high performance complementary circuits, Adv Funct Mater. 24 (2014) 6252–6261. https://doi.org/10.1002/adfm.201400850.
  25. [25]B. Sun, W. Hong, E.S. Thibau, H. Aziz, Z.H. Lu, Y. Li, Polyethylenimine (PEI) As an Effective Dopant to Conveniently Convert Ambipolar and p-Type Polymers into Unipolar n-Type Polymers, ACS Appl Mater Interfaces. 7 (2015) 18662–18671. https://doi.org/10.1021/acsami.5b05097.
  26. [26]X. Cheng, Y.Y. Noh, J. Wang, M. Tello, J. Frisch, R.P. Blum, A. Vollmer, J.P. Rabe, N. Koch, H. Sirringhaus, Controlling electron and hole charge injection in ambipolar organic field-effect transistors by self-assembled monolayers, Adv Funct Mater. 19 (2009) 2407–2415. https://doi.org/10.1002/adfm.200900315.
  27. [27]O.D. Jurchescu, A. Meetsma, T.T.M. Palstra, Low-temperature structure of rubrene single crystals grown by vapor transport, Electrochemical and Solid-State Letters. 9 (2006) 330–334. https://doi.org/10.1147/S0108768106003053/BK5027CP995HSUP9.FCF.
  28. [28]J. Takeya, M. Yamagishi, Y. Tominari, R. Hirahara, Y. Nakazawa, T. Nishikawa, T. Kawase, T. Shimoda, S. Ogawa, Very high-mobility organic single-crystal transistors with in-crystal conduction channels, Appl Phys Lett. 90 (2007) 102120. https://doi.org/10.1063/1.2711393.
  29. [29]W. Xie, K.A. McGarry, F. Liu, Y. Wu, P.P. Ruden, C.J. Douglas, C.D. Frisbie, High-mobility transistors based on single crystals of isotopically substituted rubrene- d 28, Journal of Physical Chemistry C. 117 (2013) 11522–11529. https://doi.org/10.1021/jp402250v.
  30. [30]A.L. Briseno, S.C.B. Mannsfeld, M.M. Ling, S. Liu, R.J. Tseng, C. Reese, M.E. Roberts, Y. Yang, F. Wudl, Z. Bao, Patterning organic single-crystal transistor arrays, Nature. 444 (2006) 913–917. https://doi.org/10.1038/nature05427.
  31. [31]D.A. Da Silva Filho, E.G. Kim, J.L. Brédas, Transport properties in the rubrene crystal: Electronic coupling and vibrational reorganization energy, Advanced Materials. 17 (2005) 1072–1076. https://doi.org/10.1002/adma.200401866.
  32. [32]S. Yanagisawa, Y. Morikawa, A. Schindlmayr, HOMO band dispersion of crystalline rubrene: Effects of self-energy corrections within the GW approximation, Phys Rev B Condens Matter Matter Phys. 88 (2013) 1–7. https://doi.org/10.1103/PhysRevB.88.115438.
  33. [33]S.I. MacHida, Y. Nakayama, S. Duhm, Q. Xin, A. Funakoshi, N. Ogawa, S. Kera, N. Ueno, H. Ishii, Highest-occupied-molecular-orbital band dispersion of rubrene single crystals as observed by angle-resolved ultraviolet photoelectron spectroscopy, Phys Rev Lett. 104 (2010) 156401. https://doi.org/10.1103/PhysRevLett.104.156401.
  34. [34]A. Vollmer, R. Ovsyannikov, M. Gorgoi, S. Krause, M. Oehzelt, A. Lindblad, N. Mrtensson, S. Svensson, P. Karlsson, M. Lundqvist, T. Schmeiler, J. Pflaum, N. Koch, Two dimensional band structure mapping of organic single crystals using the new generation electron energy analyzer ARTOF, J Electron Spectros Relat Phenomena. 185 (2012) 55–60. https://doi.org/10.1016/j.elspec.2012.01.003.
  35. [35]Y. Nakayama, Y. Uragami, S. Machida, K.R. Koswattage, D. Yoshimura, H. Setoyama, T. Okajima, K. Mase, H. Ishii, Full picture of valence band structure of rubrene single crystals probed by angle-resolved and excitation-energy-dependent photoelectron spectroscopy, Applied Physics Express. 5 (2012) 1–4. https://doi.org/10.1143/APEX.5.111601.
  36. [36]J. Nitta, K. Miwa, N. Komiya, E. Annese, J. Fujii, S. Ono, K. Sakamoto, The actual electronic band structure of a rubrene single crystal, Sci Rep. 9 (2019) 1–7. https://doi.org/10.1038/s41598-019-46080-4.
  37. [37]M. Fischer, M. Dressel, B. Gompf, A.K. Tripathi, J. Pflaum, Infrared spectroscopy on the charge accumulation layer in rubrene single crystals, Appl Phys Lett. 89 (2006) 182103. https://doi.org/10.1063/1.2370743/919315.
  38. [38]C. Ohashi, S. Izawa, Y. Shinmura, M. Kikuchi, S. Watase, M. Izaki, H. Naito, M. Hiramoto, Hall Effect in Bulk-Doped Organic Single Crystals, Advanced Materials. 29 (2017) 1605619. https://doi.org/10.1002/adma.201605619.
  39. [39]A. Dai, Y. Zhou, A.L. Shu, S.K. Mohapatra, H. Wang, C. Fuentes-Hernandez, Y. Zhang, S. Barlow, Y.L. Loo, S.R. Marder, B. Kippelen, A. Kahn, Enhanced charge-carrier injection and collection via lamination of doped polymer layers p-doped with a solution-processible molybdenum complex, Adv Funct Mater. 24 (2014) 2197–2204. https://doi.org/10.1002/adfm.201303232.
  40. [40]C.K. Chan, F. Amy, Q. Zhang, S. Barlow, S. Marder, A. Kahn, N-type doping of an electron-transport material by controlled gas-phase incorporation of cobaltocene, Chem Phys Lett. 431 (2006) 67–71. https://doi.org/10.1016/j.cplett.2006.09.034.
  41. [41]R.A. Laudise, C. Kloc, P.G. Simpkins, T. Siegrist, Physical vapor growth of organic semiconductors, J Cryst Growth. 187 (1998) 449–454. https://doi.org/10.1016/S0022-0248(98)00034-7.
  42. [42]J. Kloc, C.; Siegrist, T.; Pflaum, Springer Handbook of Crystal Growth, in: G. Dhanaraj, K. Byrappa, V. Prasad, M. Dudley (Eds.), Springer Handbook of Crystal Growth, Springer Berlin Heidelberg, Berlin, Heidelberg, 2010: pp. 845–867. https://doi.org/10.1007/978-3-540-74761-1.
  43. [43]E. Giangrisostomi, R. Ovsyannikov, F. Sorgenfrei, T. Zhang, A. Lindblad, Y. Sassa, U.B. Cappel, T. Leitner, R. Mitzner, S. Svensson, N. Mårtensson, A. Föhlisch, Low Dose Photoelectron Spectroscopy at BESSY II: Electronic structure of matter in its native state, J Electron Spectros Relat Phenomena. 224 (2018) 68–78. https://doi.org/10.1016/j.elspec.2017.05.011.
  44. [44]N. Koch, D. Pop, R.L. Weber, N. Böwering, B. Winter, M. Wick, G. Leising, I. V. Hertel, W. Braun, Radiation induced degradation and surface charging of organic thin films in ultraviolet photoemission spectroscopy, Thin Solid Films. 391 (2001) 81–87. https://doi.org/10.1016/S0040-6090(01)00961-0.
  45. [45]F. Bussolotti, J. Yang, T. Yamaguchi, K. Yonezawa, K. Sato, M. Matsunami, K. Tanaka, Y. Nakayama, H. Ishii, N. Ueno, S. Kera, Hole-phonon coupling effect on the band dispersion of organic molecular semiconductors, Nat Commun. 8 (2017) 173. https://doi.org/10.1038/s41467-017-00241-z.
  46. [46]S. CiucHi, R.C. Hatch, H. Höchst, C. Faber, X. Blase, S. Fratini, Molecular fingerprints in the electronic properties of crystalline organic semiconductors: From experiment to theory, Phys Rev Lett. 108 (2012). https://doi.org/10.1103/PhysRevLett.108.256401.
  47. [47]D. Käfer, G. Witte, Growth of crystalline rubrene films with enhanced stability, Physical Chemistry Chemical Physics. 7 (2005) 2850. https://doi.org/10.1039/b507620j.
  48. [48]S. Hüfner, Photoelectron Spectroscopy, Springer Berlin Heidelberg, Berlin, Heidelberg, 2003. https://doi.org/10.1007/978-3-662-09280-4.
  49. [49]S. Ciuchi, S. Fratini, Band dispersion and electronic lifetimes in crystalline organic semiconductors, Phys Rev Lett. 106 (2011). https://doi.org/10.1103/PhysRevLett.106.166403.
  50. [50]L. Plucinski, J. Minár, B.C. Sell, J. Braun, H. Ebert, C.M. Schneider, C.S. Fadley, Band mapping in higher-energy x-ray photoemission: Phonon effects and comparison to one-step theory, Phys Rev B Condens Matter Mater Phys. 78 (2008) 1–8. https://doi.org/10.1103/PhysRevB.78.035108.
  51. [51]R.C. White, C.S. Fadley, M. Sagurton, Z. Hussain, Angle-resolved x-ray photoemission from the valence bands of tungsten with high angular resolution and temperature variation, Phys Rev B. 34 (1986) 5226–5238. https://doi.org/10.1103/PhysRevB.34.5226.
  52. [52]Z. Hussain, C.S. Fadley, S. Kono, L.F. Wagner, Temperature-dependent angle-resolved x-ray photoemission study of the valence bands of single-crystal tungsten: Evidence for direct transitions and phonon effects, Phys Rev B. 22 (1980) 3750–3766. https://doi.org/10.1103/PhysRevB.22.3750.
  53. [53]S. Kasap, Principles of Electronic Materials and Devices, 4th ed., McGraw-Hill, Inc., USA, 2006.
  54. [54]S. Olthof, W. Tress, R. Meerheim, B. Lüssem, K. Leo, Photoelectron spectroscopy study of systematically varied doping concentrations in an organic semiconductor layer using a molecular p-dopant, J Appl Phys. 106 (2009). https://doi.org/10.1063/1.3259436.
  55. [55]M. Oehzelt, N. Koch, G. Heimel, Organic semiconductor density of states controls the energy level alignment at electrode interfaces, Nat Commun. 5 (2014). https://doi.org/10.1038/ncomms5174.
  56. [56]J. Li, I. Duchemin, O.M. Roscioni, P. Friederich, M. Anderson, E. Da Como, G. Kociok-Köhn, W. Wenzel, C. Zannoni, D. Beljonne, X. Blase, G. D’Avino, Host dependence of the electron affinity of molecular dopants, Mater Horiz. 6 (2019) 107–114. https://doi.org/10.1039/c8mh00921j.
  57. [57]H. Ding, Y. Gao, Electronic structure at rubrene metal interfaces, Appl Phys A Mater Sci Process. 95 (2009) 89–94. https://doi.org/10.1007/S00339-008-5038-5/METRICS.

Paper details

vlnc:W_623w2sqn
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents