betaFeedback

WorksPhysics and Astronomy

Porous SiO2_2 coated dielectric metasurface with consistent performance independent of environmental conditions

Abstract

With the rapid advances of functional dielectric metasurfaces and their integration on on-chip nanophotonic devices, the necessity of metasurfaces working in different environments, especially in biological applications, arose. However, the metasurfaces' performance is tied to the unit cell's efficiency and ultimately the surrounding environment it was designed for, thus reducing its applicability if exposed to altering refractive index media. Here, we report a method to increase a metasurface's versatility by covering the high-index metasurface with a low index porous SiO2_2 film, protecting the metasurface from environmental changes while keeping the working efficiency unchanged. We show, that a covered metasurface retains its functionality even when exposed to fluidic environments.

Introduction

Metamaterials are artificially designed structures whose optical properties do not primarily arise from the choice of material itself but rather from the design and distribution of so called single meta-atoms. These meta-atoms are normally arranged in a sub-wavelength periodic lattice and allow for an unparalleled wavefront control near their resonance. As its 2D-variant, metasurfaces excel at compact applications in on-chip nanophotonic devices [1, 2, 3]. Related advanced research fields include linear [4, 5, 6] and nonlinear imaging [7, 8] and holography [9, 10, 11, 12], optical cloaking [13, 14] and even biomedical applications such as the sensing of proteins [2, 15] or the use of optical tweezers to confine and manipulate particles [16, 17, 18, 19, 20].

Especially all-dielectric metasurfaces benefit from applications that work in transmission and their efficiency is determined by the single unit cell that consists of high-index nanostructures in a low-index environment (generally air) [21, 22]. Because the designed utility will usually be achieved in a predetermined environment the properties of the metasurface change when the refractive index of the surrounding material is changing. Furthermore, in order for the metasurfaces to work at high diffraction efficiencies, it is beneficial to choose a high refractive index contrast between the nanostructures and the surrounding medium, allowing for tighter confinement of the excited modes and a reduced height of the structures.

As a consequence, most meta-atom designs are rendered suboptimal if transferred to another refractive index environment and would need to be redesigned to work properly. To illustrate this effect, we calculated the transmission of a typically geometric-phase metasurface made of silicon nanofins on a glass substrate for different refractive index values of the surrounding host material nHn_{\mathrm{H}}. The effect of a varying refractive index on the transmission behavior of a unit cell can be seen in Figure 1a. For geometric-phase metasurfaces, phase information is applied to the transmitted light via polarization conversion of an incident circularly polarized state.

Image not extracted

Figure 1. a) Transmission for the co- and cross-polarization of a metasurface made of high index Si nanofins (length L=180L = 180 nm, width W=95W = 95 nm, height H=600H = 600 nm) in dependence of the host medium’s refractive index nHn_{\mathrm{H}}. An increase in the refractive index reduces the conversion efficiency of the unit cell (shown in the inset). b) Calculated transmission of the cross-polarization for a variation in Si nanofin length and width. The values above the red line are plotted for the transmission with air as the host medium whereas the values below the red line represent the transmitted cross-polarization in the case that water surrounds the Si nanofins. The calculations of both panels were done using the RCWA method. The simulation is done for a wavelength of 800 nm, a Si height of 600 nm and a unit cell periodicity of 400 nm.

Therefore, we calculated the transmission for both circular states whereas co-polarization signifies the same helicity as the incident light and cross-polarization represents the converted polarization that carries the desired phase information. Both the transmitted co- and cross-polarization change significantly with the refractive index of the environment thus reducing the metasurface’s efficiency, e.g., the ability to alter the phase of the transmitted light in geometric-phase metasurfaces (see Figure 1a).

Metasurface design and fabrication

By changing the surrounding environment, the host medium of the meta-atoms also changes, thus typically resulting in a reduced transmission and diffraction efficiency. In this work, we provide a solution to this problem by coating the metasurface with porous SiO2_2, hence preventing any changes to the refractive index of the surrounding medium that is in direct contact with the meta-atoms by creating a buffer layer. As noted before, the highest efficiency for dielectric metasurfaces can be obtained for high-index structures in a low-index environment. Therefore, it is desired to embed the nanostructures into a material with a refractive index close to one. As for the design of the metasurface itself, we utilize the Panacharatnam-Berry phase concept for metasurfaces [23] and optimize the cross-polarization transmission for a wavelength of 800 nm. Figure 1b shows the results for varying parameters of the width and length of the Si nanofin and different host media (air nH=1n_{\mathrm{H}}=1 and water nH=1.3n_{\mathrm{H}}=1.3). The initial parameter sets are chosen as 200 nm x 80 nm with a height of 600 nm to give a high transmission of nearly 97% if the structures are embedded in air. From Figure 1b, one can see that the transmission for these sets of parameters already drops by 10% when the structures are embedded in water.

Next, we fabricate the metasurfaces for these parameters by patterning an amorphous silicon film via electron beam lithography and dry etching. The fabrication follows a standard procedure (Figure 2a), by depositing 600 nm amorphous silicon on a glass substrate and spin-coating 270 nm of positive PMMA photoresist and 35 nm of Electra 92 as a conducting layer. After patterning via electron beam lithography with an acceleration voltage of 20 kV at a dose of 220 μC/cm2\mu\mathrm{C}/\mathrm{cm}^{2} and developing the exposed PMMA resist, a 20 nm thick chromium mask is deposited as an etching mask for the silicon. The following reactive ion etching utilizes a pseudo-Bosch process using SF6\mathrm{SF}_6 as the etching gas and C4F8\mathrm{C}_4\mathrm{F}_8 as the polymerization gas. Finally, the chromium mask is removed using chromium etch and the porous SiO2\mathrm{SiO}_2 is applied via a dip-coating procedure.

The synthesis of these films is based on the work of Lozano-Castelló [24]. Tetraethylorthosilicate, Pluronic F-127, hydrochloric acid, water, and ethanol were mixed in a molar ratio of 1: 6.6⋅10−36.6 \cdot10^{-3}: 6.6⋅10−36.6 \cdot10^{-3}: 4.62: 22.60. After plasma cleaning for 20 min the substrate was dip-coated with the above-mentioned solution at a relative humidity of 20% and a constant speed of 4 mm s−1\mathrm{s}^{-1}. After curing of the film at 120 °C for about 1 h the sample was calcined at 450 °C (1 °C min−1\mathrm{min}^{-1}) for 5 h in air. The coating procedure was repeated three times, leading to a 1 μ\mum thick highly porous film and thus to a minimal refractive index.

To prevent other materials like liquids from penetrating the pores of the porous SiO2\mathrm{SiO}_2, we apply an additional film of a transparent dielectric material. This step is supposed to protect the pores from filling for example with water (see § 3). Here, we use a 20 nm thick MgF2\mathrm{MgF}_2 layer deposited by electron beam evaporation. The final sample layout is shown in Figure 2b. Because of the large distance between the Si nanofins and the MgF2\mathrm{MgF}_2 layer, no influence on the optical properties is expected due to the localized modes inside the silicon nanofins.

Fabrication procedure, unit cell cross-section, and SEM image of the metasurface

Figure 2. a) Fabrication procedure for the metasurfaces. Following silicon deposition, the metasurfaces are patterned on a positive PMMA photoresist using electron beam lithography. After the PMMA development, a chromium mask is used as a protective mask for the ensuing etching process. Finally, the chromium mask is removed and the porous SiO2\mathrm{SiO}_2 film is applied via dip-coating. b) Unit cell cross-section of the finished sample. As the final step, an MgF2\mathrm{MgF}_2 layer is added to close the pores of the sample. c) SEM image of a fabricated sample before the chromium mask removal under a viewing angle of 45°.

After producing the mentioned design, a few iterative adjustments have been made to the nanofin dimensions to improve the measured transmissive spectra that deviated from the simulations due to tolerances in the fabrication and some uncertainties in the refractive index value of the amorphous silicon. In the eventually used design, the height was lowered to 530 nm while the length and width were fixed at 240 nm x 120 nm. A scanning electron microscopy image of one sample made before the chromium mask removal is shown in Figure 2c.

Porous SiO2\mathrm{SiO}_{2} film characterization

For the use in optical applications, the coating of the metasurface has to fulfill certain criteria: First, the refractive index of the coating should be as low as possible because a high refractive index lowers the maximum conversion efficiency of the Si nanofins as they will not allow for tight confinement of the excited modes. Second, the surface roughness should be small as a rough surface can alter the transmitted wavefronts and impair the metasurface’s functionality. With both efficiency and functionality suffering from an improper coating its applicability would be severely limited and therefore investigating the refractive index as well as the surface roughness is of great interest when concluding the viability of this particular coating.

Here, the porous SiO2\mathrm{SiO}_{2} film was characterized via ellipsometry and atomic force microscopy (AFM) to measure the refractive index and surface roughness corresponding to the used recipe mentioned in § 2. The refractive index measurement is shown in Figure 3a. In the spectral range from 500 nm - 900 nm, the refractive index decreases gradually towards longer wavelengths and reaches 1.182 at the target wavelength of 800 nm, lower than related work from Wang et al. [25] of 1.23 who also employed a sol-gel approach. Work done by Xi et al. [26] even reports a film deposition with a refractive index of as low as 1.05 using electron beam evaporation of SiO2\mathrm{SiO}_{2} granules at low vapor flux and deposition under 85° substrate tilt angle resulting in the formation of tilted SiO2\mathrm{SiO}_{2} nanopillars. While these coatings are very beneficial for antireflection coatings, their applicability as a protective layer for metasurfaces might be unsuited especially since the deposition method will introduce shadowing effects due to the already present Si nanofins potentially resulting in an inhomogeneous coating.

Measured refractive index, influence of humidity, and surface roughness

Figure 3. a) Ellipsometry measurement of a porous SiO2\mathrm{SiO}_{2} layer for a wavelength range of 500 nm - 900 nm. The refractive index (n) decreases towards longer wavelengths and reaches a value of 1.182 at 800 nm. b) Measured refractive index (n) of a porous SiO2\mathrm{SiO}_{2} layer for increasing and decreasing relative humidity (Rel. H.). The refractive index increases with higher humidity; liquid environments, e.g. water, can enter the pores and thus change the host medium’s refractive index. The porous SiO2\mathrm{SiO}_{2} layer also exhibits a hysteresis for decreasing humidity which means that once exposed to water the humidity partly remains in the layer and does not immediately leave the pores. c) AFM measurement of the porous SiO2\mathrm{SiO}_{2} layer’s surface. The surface roughness yields an RMS value of 3.5 nm.

Regarding the exposition of our samples to water, the influence of varying humidity in the environment on the refractive index is shown in Figure 3b. The measured refractive index rises with increasing humidity indicating that water is penetrating the pores which will impact the performance of the coated samples. As mentioned in § 2, an additional MgF2\mathrm{MgF}_{2} film is supposed to prevent this by closing the top pores and waterproofing the sample. The porous film also exhibits a small hysteresis, showing that the water does not immediately leave the film once the surrounding humidity is lowered again.

As for the AFM measurement, the evaluated surface roughness yields a root mean square (RMS) value of 3.5 nm. Regarding the typically used wavelengths ranging from visible to infrared for metasurface applications, the surface of the porous SiO2\mathrm{SiO}_{2} layer can be considered flat which is a desirable property for optical applications.

Sample characterization and optical measurements

To evaluate the influence of the porous SiO2_2 coating on the meta-atoms’ performance, first, the transmitted co- and cross-polarization intensities (IcoI_{\mathrm{co}} and IcrossI_{\mathrm{cross}}), as well as the conversion efficiency ηconv=Icross/(Icross+Ico)\eta_{\mathrm{conv}} = I_{\mathrm{cross}}/(I_{\mathrm{cross}} + I_{\mathrm{co}}) of the metasurface before and after the coating via porous SiO2_2 are determined. Since the metasurface is designed to act as a half-wave plate, IcrossI_{\mathrm{cross}} represents the intensity converted to its cross-polarization for circularly polarized light (opposite helicity). As for the metasurfaces, additional samples containing a linear phase gradient based on the geometric phase [23] have been fabricated to diffract the light under angles of 0°, 5°, and 10°. For the sample with the 0° diffraction angle where all the nanofins are oriented the same way, the transmission from 700 nm – 1000 nm was measured with a Bruker Hyperion FT-IR microscope. Albeit, only including linear polarizers, if these are oriented at ±45° towards the rectangular nanofins’ principle axis the broadband transmission measurement effectively averages the two possible co- or cross-polarization measurements, namely L→L and R→R for the transmitted co-polarization and L→R as well as R→L for the cross-polarization. Figure 4 shows the transmitted co- and cross-polarization intensities and the conversion efficiency with and without the porous SiO2_2 coating. Before applying the coating, the sample shows cross-polarization peaks around 825 nm and 940 nm whereas the conversion efficiency shows two peaks at 845 nm and 940 nm reaching up to 95%. After the coating, the peaks shift by roughly 40 nm towards longer wavelengths. The conversion efficiency also decreases by up to 5% at the peak positions. While a small decrease in efficiency is expected, note that the fabrication parameters were optimized for air as the host medium. For proper operation at maximum efficiency, the unit cell’s parameters need to be calculated considering the porous coating as the surrounding refractive medium.

Figure 4. Broadband transmission measurement of co- and cross-polarization (tcot_{\mathrm{co}} and tcrosst_{\mathrm{cross}}) as well as conversion efficiency (ηconv\eta_{\mathrm{conv}}) for the 0° diffraction angle metasurface. (left) Spectra for the fabricated sample before coating with porous SiO2_2. (right) Spectra after applying a 1 µm thick porous SiO2_2 layer. After the coating, the peaks shift by roughly 40 nm towards longer wavelengths.

The results of the transmitted cross-polarization from Figure 4 (right) will be the baseline for comparison to evaluate the following measurements. After depositing a 20 nm layer of MgF2_2 the measurements using the FT-IR microscope were repeated (see Figure 5 (left)). To expose the metasurface to water, a droplet has been placed on top of the fields. The blue curve shows that although the spectrum keeps a similar shape, the derivation from the original curve is neither negligible nor satisfactory with the transmission decreasing by as much as 20% near 1000 nm. The measurement implies that despite the supposed protection from the MgF2_2 layer water penetrated into the porous SiO2_2 film and reached the nanofins. This might be due to the MgF2_2 layer also being porous when deposited via electron beam evaporation. The change in spectral behavior however is less pronounced compared to the difference from Figure 4 since the spectrum shifts by only 20 nm towards longer wavelengths. Still, to resolve the issue of water penetrating the porous film an additional layer of 500 nm PMMA is applied to the surface via spin-coating. The film thickness of 500 nm was chosen to ensure that we obtain a dense and closed layer even covering the edges of the sample substrate. In hindsight, applying the waterproofing layer via dip-coating might be more reliable than a spin-coating approach because it can cover the uneven edges better. The measurements show that the water now barely influences the spectral behavior of the sample (Figure 5). Note that the placed water droplet on the sample surface slowly evaporated during the measurements and that the focus of the FT-IR microscope had to be adjusted repeatedly, potentially leading to less light collection from the condenser lens which could explain the slightly lower transmission values. Hence, small deviations in the spectra might arise from the re-adjustment of the setup and some inhomogenous thickness of the water layer. However, the results show that the porous SiO2\mathrm{SiO}_2 coating in combination with a waterproofing layer allows the metasurface to retain its efficiency and specral characteristics if exposed to different refractive media.

Comparison of transmitted cross-polarization for MgF2 and MgF2 + PMMA layers

Figure 5. (left) Comparison between the transmitted cross-polarization after applying the porous SiO2\mathrm{SiO}_2 coating (see also Figure 4 right) and the transmitted cross-polarization after adding a 20 nm MgF2\mathrm{MgF}_2 layer as well as exposing the metasurface to water. The transmission for these two curves differs noticeably. The measurement indicates that the water entered the porous SiO2\mathrm{SiO}_2 layer despite the MgF2\mathrm{MgF}_2 film and thus changed the refractive index of the host medium. (right) Here, an additional 500 nm PMMA film has been added to realize a waterproofing layer. These two curves show a close resemblance and the water barely seems to influence the metasurface’s transmission.

In addition to the previous measurements, we simulated the spectral behavior of these metasurfaces when exposed to different environments. The left panel of Figure 6 shows the simulated transmitted cross-polarization for an uncoated sample exposed to air and water whereas the right panel of Figure 6 shows the influence of the porous coating and compares the simulated transmitted cross-polarization if a coated Si antenna is exposed to air and water. Note that the simulation does not include the additionally applied MgF2\mathrm{MgF}_2 and PMMA layers. Focusing on the peak shown at 830 nm, it can be seen from Figure 6 (left) that the transmitted cross-polarization and thus the overall efficiency of the metasurface drops due to the changed environment. Also, the dip for the uncoated metasurface located at 870 nm shifts by roughly 40 nm towards longer wavelengths when exposing it to water. If the metasurface is embedded in the porous SiO2\mathrm{SiO}_2 we only observe a spectral shift of 20 nm (Figure 6 (right)). More importantly, after coating there is negligible influence in the spectral behavior for air and water exposition (blue and green curves). The simulated curves mostly match with the measurements albeit showing an overall larger transmission than the experimentally measured ones. Note that the measured and simulated curves not only represent the spectral behavior of the 0∘0^\circ phase gradient metasurface but also of the 5∘5^\circ and 10∘10^\circ phase gradient metasurfaces since the behavior of the entire sample originates from the spectral behavior of the unit cell. However, small deviations might occur due to weak coupling between neighboring nanoantennas.

Simulated spectral behavior of uncoated and porous SiO2 coated metasurfaces

Figure 6. (left) Simulated transmission of the cross-polarization state of the uncoated metasurface when exposed to air and water. A spectral shift to larger wavelengths by roughly 40 nm can be observed if the sample is exposed to water. (right) Simulated transmission of the cross-polarization state of the uncoated metasurface as well as the transmission of the porous SiO2 coated sample when exposed to air and water. The difference between the latter two is marginal.

With the metasurface retaining its efficiency after the coating, the gradient-phase fields that diffract the light under an angle of 5∘5^\circ and 10∘10^\circ are used to investigate the functionality for the finished sample with and without water. Here, we use polarization optics to realize circularly polarized light and focus 800 nm laser light on the gradient fields. Depending on the circular input polarization (L or R) the +1 or -1 diffraction order will show up in the transmitted light. By imaging the Fourier plane of the collecting microscope objective, we spatially separate the k-vectors of the transmitted light, these being the +1 and -1 diffraction order (cross-polarization) as well as the light that did not interact with the metasurface (co-polarization). Figure 7a shows an illustration of the used 4f-setup and Figure 7b shows the obtained camera images from the measurement of the 5∘5^\circ- and 10∘10^\circ-diffraction angle gradient-phase metasurfaces for incident left and right circular polarized light, respectively. For the measurement with a fluidic environment, the sample was placed in a cuvette filled with water.

4f measurement setup and camera images of diffraction orders in air and water

Figure 7. (a) Illustration of the 4f measurement setup. A linear polarizer and a λ/4-plate are used to create a circularly polarized state and two lenses behind the microscope objective spatially separate the diffraction orders that are captured on a camera. (b) Camera images showing the diffraction orders of the 5∘5^\circ and 10∘10^\circ linear phase gradient metasurfaces in the Fourier plane at 800 nm. (left) +1 and -1 diffraction orders (incident L and R) for metasurfaces that are exposed to air. (right) +1 and -1 diffraction orders from the same metasurfaces after placing the sample in water. The diffraction orders (location and strength) do not noticeably change when exposing the sample to water.

The measurements show, that the diffraction angles and the strength of the diffraction spots stay the same even after placing the sample in water. The measurements on such geometric-phase metasurfaces illustrate that the functionality stays unaffected if the sample is placed inside an environment with a different refractive index. The small tradeoff in slightly lower maximum diffraction efficiency due to the porous SiO2\mathrm{SiO}_{2} coating compared to air as the host medium can be considered beneficial if the metasurface is supposed to operate in an environment with varying refractive index. Furthermore, the porous SiO2\mathrm{SiO}_{2} coating also acts as a protection layer for the small nanostructures, making the sample surface more robust in harsh environments.

Conclusion

In this work, we present a method to protect a dielectric metasurface from the influence of a changing environment by coating the sample in a porous SiO2\mathrm{SiO}_{2}-film. The low refractive index of this film allows the metasurface to keep a relatively large index contrast between the dielectric nanostructures and the surrounding host medium. By fixing the nanostructures’ host medium, especially to one with a low refractive index, the metasurface retains its functionality at high efficiency and can even be placed in fluidic environments without changing the functionality. However, since the porous coating can easily soak itself with liquids like water and thus change the index contrast between the host medium and the meta-atoms, waterproofing by adding another transparent layer is necessary. To solve this, we applied a layer of PMMA via spin-coating. For this procedure to work, a sufficiently smooth sample surface or a thick PMMA film is required to ensure the waterproofing. Employing another dip-coating procedure, similar to how the porous SiO2\mathrm{SiO}_{2}-film was applied, might proof to be more reliable, especially regarding the edges of the sample substrate that will not be covered by spin-coating alone. Furthermore, the porous coating also acts as a protection against physical damages and might also overcome one of the hurdles for commercializing the incorporation of metasurfaces in everyday devices, as suggested by Gun-Yeal Lee et al. [11].

Acknowledgment. The authors like to thank Cedrik Meier for providing access to the EBL system and Basudeb Sain for help with the sample fabrication.

Funding. This project has received funding from the European Research Council (ERC) under the European Union’s Horizon 2020 research and innovation programme (grant agreement No 724306) and the Deutsche Forschungsgemeinschaft (DFG No. ZE953/11-1).

Disclosures. The authors declare no conflicts of interest.

Data availability. Data underlying the results presented in this paper are not publicly available at this time but may be obtained from the authors upon reasonable request.

References

  1. [1]Z. Wang, T. Li, A. Soman, D. Mao, T. Kananen, and T. Gu, "On-chip wavefront shaping with dielectric metasurface," Nat. Commun. 10(1): 3547 (2019).DOI
  2. [2]M. Consales, G. Quero, S. Spaziani, M. Principe, A. Micco, V. Galdi, A. Cutolo, and A. Cusano, "Metasurface-Enhanced Lab-on-Fiber Biosensors," Laser Photonics Rev. 14(12): 2000180 (2020).DOI
  3. [3]N. Yu and F. Capasso, "Flat optics with designer metasurfaces," Nat. Mater. 13(2): 139-150 (2014).DOI
  4. [4]G.-Y. Lee, J. Sung, and B. Lee, "Metasurface optics for imaging applications," MRS Bull. 45(3): 202-209 (2020).DOI
  5. [5]S. Colburn, A. Zahn, and A. Majumdar, "Metasurface optics for full-color computational imaging," Sci. Adv. 4(2): eaar2114 (2018).DOI
  6. [6]S. Zhang, C. L. Wong, S. Zeng, R. Bi, K. Tai, K. Dholakia, and M. Olivo, "Metasurfaces for biomedical applications: imaging and sensing from a nanophotonics perspective," Nanophotonics 10(1): 259-293 (2021).
  7. [7]C. Schlickriede, S. S. Kruk, L. Wang, B. Sain, Y. Kishvar, and T. Zentgraf, "Nonlinear Imaging with All-Dielectric Metasurfaces," Nano Lett. 20(6): 4370-4376 (2020).DOI
  8. [8]K. Konishi, T. Higuchi, J. Li, J. Larsson, S. Ishii, and M. Kuwata-Gonokami, "Polarization-Controlled Circular Second-Harmonic Generation from Metal Hole Arrays with Threefold Rotational Symmetry," Phys. Rev. Lett. 112(13): 135502 (2014).pubmed.ncbi.nlm.nih.gov/24745436
  9. [9]L. Huang, Z. Shuang, and T. Zentgraf, "Metasurface holography: from fundamentals to applications," Nanophotonics 7(6): 1169-1190 (2018).DOI
  10. [10]W. Ye, F. Zeuner, X. Li, B. Reineke, S. He, C.-W. Qiu, J. Liu, Y. Wang, S. Zhang, and T. Zentgraf, "Spin and wavelength multiplexed nonlinear metasurface holography," Nat. Commun. 7(1): 11930 (2016).DOI
  11. [11]G.-Y. Lee, J. Sung, and B. Lee, "Recent advances in metasurface hologram technologies (Invited paper)," ETRI J. 41(1): 10-22 (2019).DOI
  12. [12]P. Georgi, Q. Wei, B. Sain, C. Schlickriede, Y. Wang, L. Huang, and T. Zentgraf, "Optical secret sharing with cascaded metasurface holography," Science Advances 7: eabf9718 (2021).DOI
  13. [13]J. Valentine, J. Li, T. Zentgraf, G. Bartal, and X. Zhang, "An optical cloak made of dielectrics." Nat. Mater. 8(7): 568-571 (2009).DOI
  14. [14]W. Cai, U. K. Chettiar, A. V. Kildishev, and V. M. Shalaev, "Optical cloaking with metamaterials," Nat. Photonics 1(4): 224-227 (2007).DOI
  15. [15]K. Svoboda and S. M. Block, "Biological applications of optical forces," Annu. Rev. Biophys. Biomol. Struct. 23: 247-285 (1994).pubmed.ncbi.nlm.nih.gov/7919782
  16. [16]T. Tchankhat, C. Schlickriede, B. Sain, F. Meyer, T. Weiss, N. Chattahm, and T. Zentgraf, "All-dielectric silicon metalens for two-dimensional particle manipulation in optical tweezers," Photon. Res. 8:1435-1440 (2020).
  17. [17]A. Ashkin and J. M. Dziedzic, "Internal cell manipulation using infrared laser traps," Proc. Natl. Acad. Sci. U. S. A. 86(20): 7914-7918 (1989).pubmed.ncbi.nlm.nih.gov/2813368
  18. [18]R. W. Steubing, S. Cheng, W. H. Wright, Y. Numajiri, and M. W. Berns, "Laser induced cell fusion in combination with optical tweezers: the laser cell fusion trap," Cytometry 12(6): 505-510 (1991).
  19. [19]S. Seeger, S. Monajembashi, K. J. Hutter, G. Futterman, J. Wolfrum, and K. O. Greulich, "Application of laser optical tweezers in immunology and molecular genetics," Cytometry 12(6): 497-504 (1991).pubmed.ncbi.nlm.nih.gov/1684929
  20. [20]L. Zhu, X. Liu, B. Sain, M. Wang, C. Schlickriede, Y. Tang, J. Deng, K. Li, J. Yang, M. Holynski, S. Zhang, T. Zentgraf, K. Bongs, Y. H. Lien, and G. Li, "A dielectric metasurface optical chip for the generation of cold atoms," Science Advances 6: eabb6667 (2020).
  21. [21]P. Qiao, W. Yang, and C. J. Chang-Hasnain, "Recent advances in high-contrast metastructures, metasurfaces, and photonic crystals," Advances in Optics and Photonics 10(1): 180-245 (2018).DOI
  22. [22]S. M. Kamali, E. Arbabi, A. Arbabi, and A. Faraon, "A review of dielectric optical metasurfaces for wavefront control," Nano Photonics 7(6): 1041-1068 (2018).arxiv.org/abs/1804.09802
  23. [23]F. Ding, A. Pors, and S. Bozhevolnyi, "Gradient metasurfaces: a review of fundamentals and applications," Rep. Prog. Phys. 81 2: 026401 (2018).
  24. [24]S. Leyva-Garcia, D. Lozano-Castello, E. Morallon, and D. Cazorla-Amoros, "Silica-templated ordered mesoporous carbon thin films as electrodes for micro-capacitors," J. Mater. Chem. A 4 (2016).
  25. [25]N.-F. Wang, T.-W. Kuo, Y.-Z. Tsai, S.-X. Lin, P.-K. Hung, C.-L. Lin, and M.-P. Houng, "Porous SiO2/MgF2 broadband antireflection coatings for superstrate-type silicon-based tandem cells." Opt. Express 20(7): 7445-7453 (2012).
  26. [26]J. Q. Xi, M. F. Schubert, J. K. Kim, E. F. Schubert, M. Chen, S.-Y. Lin, W. Liu, and J. A. Smart, "Optical thin-film materials with low refractive index for broadband elimination of Fresnel reflection." Nat. Photonics 1(3): 176-179 (2007).

Paper details

vlnc:W_65tv2ydp
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 10

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents