betaFeedback

WorksPhysics and Astronomy

Prism-based compensation of group delay dispersion in the components of a femtosecond laser resonator and analysis of the influence of prism configuration on laser radiation parameters

Abstract

A mathematical algorithm is described for calculating the minimum distance between prisms and the allowable prism insertion depth into the laser beam when solving the general problem of intracavity group delay dispersion (GDD) compensation. GDD is caused by the optical elements of the master oscillator in a femtosecond laser system. The calculation was carried out using analytical and geometrical methods. The influence of changing the distance between the prisms and the depth of their insertion into the laser beam on the GDD compensation has been investigated. Under experimental conditions, this changes the Q-factor of the laser resonator, which determines the central wavelength of the radiation and its spectral width in a titanium-sapphire laser.

INTRODUCTION

Femtosecond laser systems have a wide range of applications, including chemistry, metrology, materials science, telecommunication and data transmission, energy research, biology and medicine [1]. They are also considered as promising sources of laser radiation for dielectric laser accelerators (DLA) [2, 3].

The physical principle of femtosecond pulse generation is described in [4], while the mathematical theory of mode-locking, which is essential for generating high-power femtosecond pulses, is presented in [5]. In the laser gain medium (such as a Ti:sapphire crystal), which has a relatively broad gain bandwidth, group delay dispersion (GDD) leads to spatial splitting and tilting of the femtosecond pulse front due to different refractive indices for spectral components of the radiation (see Figure 1).

The principle of compensation of group delay dispersion with minimal input of prisms into the laser beam

Figure 1. The principle of compensation of group delay dispersion (GDD) with minimal input of prisms into the laser beam: diameter of the laser beam (dd), distance between prisms (ll), path of the lower edge of the laser beam in the prism (PprP_{pr}), center of the beam (Ppr′P'_{pr}), and the upper edge of the beam (Ppr′′P''_{pr}), path of the beam in the second prism, compensating GDD in the materials of the crystal and prisms for different spectral components of the laser radiation (PcompP_{comp}), wavelength of individual spectral components (λ\lambda).

To achieve a stable mode-locking regime, the positive GDD arising from the optical elements of the laser resonator must be compensated by negative GDD. This negative GDD can be introduced using a prism-based dispersion compensator consisting of two (Figure 1) or four prisms, as described in [6]. A method for calculating such a prism compensator was proposed in [7]; however, it assumes the prisms operate in the minimum deflection mode, with the beam incident precisely at the Brewster angle and with minimal prism insertion into the laser beam.

In practice, during alignment of the master oscillator components in a femtosecond laser system [8], deviations from the Brewster angle are often inevitable. In such cases, it is more practical to keep the distance between prisms fixed and instead vary the insertion depth of the prisms into the beam, which alters the positive GDD introduced by the prism material.

The goal of this work is to develop a general mathematical algorithm that allows:

  • calculation of the minimum distance between prisms for minimal prism insertion;

  • determination of the necessary excessive insertion depth of the prisms for a fixed distance between prisms exceeding the minimum for a given beam diameter;

  • specification of arbitrary angles of incidence (not limited to the Brewster angle);

  • consideration of arbitrary apex angles of the prisms used in the compensator.

The algorithm is implemented using both analytical and geometrical methods.

The laser radiation has a continuous spectrum ranging from 790 nm to 810 nm. Figure 1 shows the propagation paths of three spectral components with wavelengths of 790 nm, 800 nm, and 810 nm, representing the lower edge, the central wavelength, and the upper edge of the spectrum, respectively. For the beam center, the 790 nm and 810 nm components after the first prism are not shown. The angular divergence of the spectral components in the figure is increased, and the distances between optical elements are reduced for clarity.

PROBLEM FORMULATION

Before calculating the group delay dispersion (GDD) in the laser resonator elements and determining the conditions for its compensation using a two-prism compressor (including the minimum distance between the prisms and the dependence of the required additional prism insertion on the additional spacing of prisms), auxiliary computations are required.

To model GDD mathematically and geometrically and to determine the refractive index n(λ)n(\lambda) of laser radiation

for different wavelengths λ\lambda in the crystal and prism materials, the Sellmeier representation is used [9]:

n2−1=∑j=13λ2⋅Bjλ2−λj2,(1)n^2 - 1 = \sum_{j=1}^{3} \frac{\lambda^2 \cdot B_j}{\lambda^2 - \lambda_j^2}, \tag*{(1)}

where the Sellmeier coefficients BjB_j and λj\lambda_j for the laser crystal (Ti:Al2_2O3_3) were taken from [10], and for the prism material (fused silica) – from [11]. Their values are shown in Table I.

MediumBjB_jλj\lambda_j (μm)
Laser crystal (Ti:Al2_2O3_3)B1=1.43134930B_1 = 1.43134930λ1=0.0726631\lambda_1 = 0.0726631
Laser crystal (Ti:Al2_2O3_3)B2=0.65054713B_2 = 0.65054713λ2=0.1193242\lambda_2 = 0.1193242
Laser crystal (Ti:Al2_2O3_3)B3=5.34140210B_3 = 5.34140210λ3=18.0282510\lambda_3 = 18.0282510
Prisms (fused silica)B1=0.69616630B_1 = 0.69616630λ1=0.0684043\lambda_1 = 0.0684043
Prisms (fused silica)B2=0.40794260B_2 = 0.40794260λ2=0.1162414\lambda_2 = 0.1162414
Prisms (fused silica)B3=0.89747940B_3 = 0.89747940λ3=9.8961610\lambda_3 = 9.8961610

Table I. The coefficients for a three-term Sellmeier expansion.

The first and second derivatives of the refractive index are obtained by differentiating Eq. (1):

dndλ=−λ0n0⋅∑j=13λj2⋅Bj(λ02−λj2)2,(2)\frac{dn}{d\lambda} = -\frac{\lambda_0}{n_0} \cdot\sum_{j=1}^{3} \frac{\lambda_j^2 \cdot B_j}{(\lambda_0^2-\lambda_j^2)^2}, \tag*{(2)}
d2ndλ2=1n0⋅∑j=13λj2(3λ02+λj2)⋅Bj(λ02−λj2)3−1n0⋅(dndλ)2,(3)\frac{d^2n}{d\lambda^2} = \frac{1}{n_0} \cdot\sum_{j=1}^{3} \frac{\lambda_j^2(3\lambda_0^2+\lambda_j^2)\cdot B_j}{(\lambda_0^2-\lambda_j^2)^3} - \frac{1}{n_0}\cdot\left(\frac{dn}{d\lambda}\right)^2, \tag*{(3)}

where n0n_0 is the refractive index for the central wavelength λ0\lambda_0.

Figure 2 illustrates geometrical parameters used to calculate GDD compensation in the laser crystal. The angular divergence of the spectral components in the figure is increased, and the distances between optical elements are reduced for clarity.

Geometrical parameters used to calculate GDD compensation using a two-prism system

Figure 2. Geometrical parameters used to calculate GDD compensation using a two-prism system. Dashed lines indicate ray paths prior to additional insertion of the second prism by depth AA.

The incidence angle α\alpha of laser radiation polarized in the plane of the figure onto the crystal is chosen equal to the Brewster angle to minimize reflection losses:

α=arctan⁡(n0CR),(4)\alpha= \arctan(n_{0CR}), \tag*{(4)}

where n0CRn_{0CR} is the refractive index of Ti:Al2_2O3_3 crystal at the central wavelength of the laser radiation.

Both prisms are inserted into the beam of diameter dd until the transmitted power no longer increases to ensure minimum GDD.

The incidence angle Φ1\Phi_1 on the first surface of the first prism is also set to the Brewster angle:

Φ1=arctan⁡(n0PR),(5)\Phi_1 = \arctan(n_{0PR}), \tag*{(5)}

where n0PRn_{0PR} is the refractive index of the prism material (fused silica) at the central wavelength of the laser radiation.

The adjacent faces of the prisms are aligned to be parallel. In the calculations, it is acceptable to use the actual apex angle ε\varepsilon of each prism. However, in the ideal case, the apex angle ε\varepsilon is determined from the condition that the output angle Φ2\Phi_2 of the radiation with the central wavelength is equal to the incidence angle Φ1\Phi_1, which minimizes reflection losses (this corresponds to the case where the central wavelength is incident at the Brewster angle). The prisms are manufactured so that their apex angles satisfy the following condition:

ε=2⋅arcsin⁡(sin⁡(arctan⁡(n0PR))n0PR).(6)\varepsilon= 2 \cdot\arcsin\left(\frac{\sin(\arctan(n_{0PR}))}{n_{0PR}}\right). \tag*{(6)}

The remaining angles are calculated for the central wavelength of the radiation using the following formulas.

Refraction angle ψ1\psi_1:

ψ1=arcsin⁡(sin⁡Φ1n0PR),(7)\psi_1 = \arcsin\left(\frac{\sin\Phi_1}{n_{0PR}}\right), \tag*{(7)}

Incidence angle ψ2\psi_2 on the second face:

ψ2=ε−ψ1,(8)\psi_2 = \varepsilon- \psi_1, \tag*{(8)}

Output angle Φ2\Phi_2:

Φ2=arcsin⁡(n0PR⋅sin⁡ψ2).(9)\Phi_2 = \arcsin(n_{0PR} \cdot\sin\psi_2). \tag*{(9)}

Its derivatives were found by differentiation [6]:

dΦ2dnPR=sin⁡ψ2+cos⁡ψ2⋅tan⁡ψ1cos⁡Φ2,(10)\frac{d\Phi_2}{dn_{PR}} = \frac{\sin\psi_2 + \cos\psi_2 \cdot\tan\psi_1}{\cos\Phi_2}, \tag*{(10)}
d2Φ2dnPR2=tan⁡Φ2⋅(dΦ2dnPR)2−tan⁡2ψ1n0PR⋅dΦ2dnPR.(11)\frac{d^2\Phi_2}{dn_{PR}^2} = \tan\Phi_2 \cdot\left(\frac{d\Phi_2}{dn_{PR}}\right)^2 - \frac{\tan^2\psi_1}{n_{0PR}} \cdot\frac{d\Phi_2}{dn_{PR}}. \tag*{(11)}

The angular divergence ΔΦ2\Delta\Phi_2 of the radiation after passing through the first prism arises due to wave dispersion, which results from differences in the refractive index for various spectral components of the laser pulse. It is calculated using the following expression [7]:

ΔΦ2=2⋅Δλ⋅dnPRdλ,(12)\Delta\Phi_2 = 2 \cdot\Delta\lambda\cdot\frac{dn_{PR}}{d\lambda}, \tag*{(12)}

GDD IN THE LASER CRYSTAL AND ITS COMPENSATION BY A PRISM PAIR

where Δλ=λmax⁡−λmin⁡\Delta\lambda= \lambda_{\max} - \lambda_{\min} is the spectral width of the laser radiation. In our study, Δλ=810\Delta\lambda= 810 nm - 790 nm = 20 nm. dnPRdλ\frac{dn_{PR}}{d\lambda} is calculated using Eq. (2), substituting n0PRn_{0PR} obtained from Eq. (1) in place of n0n_0, and using the BjB_j and λj\lambda_j coefficients from Table I for fused silica. Similarly, the value of d2nPRdλ2\frac{d^2n_{PR}}{d\lambda^2} is calculated from Eq. (3).

Group delay dispersion (GDD) is directly related to the second derivative of the optical path of radiation in a material [6]. Since a positive GDD arises in the laser crystal (denoted as PCRP_{CR} in Figure 1), it must be compensated by introducing a negative GDD using a prism pair. The main contribution to the negative GDD is made by the second prism.

However, taking into account the finite width of the laser beam, even with minimal insertion of the prisms into the beam, an additional positive GDD arises in the material of the first prism (segment PPR1P_{PR1} in Figure 1). To compensate for this, the distance between the prisms must be increased.

With minimal prism insertion (considering the lower edge of the beam), the second prism introduces purely negative GDD. This is because the shortest wavelength spectral component of the radiation has a minimal optical path (PCOMP790nmP_{COMP790nm} in Figure 1) in the second prism, which maximizes the path difference between the long- and short-wavelength components.

With excessive insertion of the second prism (depth AA in Figure 2), along with negative GDD, it also begins to introduce positive GDD similar to the first prism. This happens because the optical path of the short-wavelength component is no longer approaching zero.

To fully compensate GDD in the system, the following condition must be satisfied:

d2PCRdλ2+d2PPRdλ2+d2PADD_PRdλ2+d2PCOMPdλ2=0,(13)\frac{d^2P_{CR}}{d\lambda^2} + \frac{d^2P_{PR}}{d\lambda^2} + \frac{d^2P_{ADD\_PR}}{d\lambda^2} + \frac{d^2P_{COMP}}{d\lambda^2} = 0, \tag*{(13)}

where d2PCRdλ2\frac{d^2P_{CR}}{d\lambda^2} is the second derivative of the optical path of radiation in the laser crystal, d2PPRdλ2\frac{d^2P_{PR}}{d\lambda^2} is the second derivative of the optical path of radiation in the prisms at their minimal insertion into the laser beam, d2PADD_PRdλ2\frac{d^2P_{ADD\_PR}}{d\lambda^2} is the second derivative of the additional optical path in the prisms caused by their excessive insertion into the laser beam, d2PCOMPdλ2\frac{d^2P_{COMP}}{d\lambda^2} is the second derivative of the optical path in the second prism for radiation that has undergone spectral spatial separation after passing through the first prism due to wave dispersion [6, 7]:

d2PCRdλ2=t(n0CR2−sin⁡2α)3/2[n0CR⋅(n0CR2−2⋅sin⁡2α)⋅d2nCRdλ2+sin⁡2α⋅(n0CR2+2⋅sin⁡2α)n0CR2−sin⁡2α⋅(dnCRdλ)2],(14)\frac{d^2P_{CR}}{d\lambda^2} = \frac{t}{\left(n_{0CR}^2-\sin^2\alpha\right)^{3/2}}\left[n_{0CR}\cdot\left(n_{0CR}^2-2\cdot\sin^2\alpha\right)\cdot\frac{d^2n_{CR}}{d\lambda^2}+\frac{\sin^2\alpha\cdot\left(n_{0CR}^2+2\cdot\sin^2\alpha\right)}{n_{0CR}^2-\sin^2\alpha}\cdot\left(\frac{dn_{CR}}{d\lambda}\right)^2\right], \tag*{(14)}
d2PPRdλ2=d⋅sin⁡εcos⁡Φ1⋅[1cos⁡(ε−ψ1)⋅(1+tan⁡(ε−ψ1)⋅sin⁡Φ1n0PR2−sin⁡2Φ1)⋅d2nPRdλ2+sin⁡2Φ1n0PR⋅cos⁡(ε−ψ1)⋅(n0PR2−sin⁡2Φ1)×(1cos⁡2(ε−ψ1)+tan⁡2(ε−ψ1)−tan⁡(ε−ψ1)⋅sin⁡Φ1n0PR2−sin⁡2Φ1)⋅(dnPRdλ)2],(15)\frac{d^{2}P_{PR}}{d\lambda^{2}}=\frac{d\cdot\sin\varepsilon}{\cos\Phi_{1}}\cdot\left[\frac{1}{\cos(\varepsilon-\psi_{1})}\cdot\left(1+\frac{\tan(\varepsilon-\psi_{1})\cdot\sin\Phi_{1}}{\sqrt{n_{0PR}^{2}-\sin^{2}\Phi_{1}}}\right)\cdot\frac{d^{2}n_{PR}}{d\lambda^{2}}+\frac{\sin^{2}\Phi_{1}}{n_{0PR}\cdot\cos(\varepsilon-\psi_{1})\cdot(n_{0PR}^{2}-\sin^{2}\Phi_{1})}\times\left(\frac{1}{\cos^{2}(\varepsilon-\psi_{1})}+\tan^{2}(\varepsilon-\psi_{1})-\frac{\tan(\varepsilon-\psi_{1})\cdot\sin\Phi_{1}}{\sqrt{n_{0PR}^{2}-\sin^{2}\Phi_{1}}}\right)\cdot\left(\frac{dn_{PR}}{d\lambda}\right)^{2}\right], \tag*{(15)}
d2PADD-PRdλ2=A⋅cos⁡(ε/2−Φ1)d⋅d2PPRdλ2,(16)\frac{d^{2}P_{ADD\text{-}PR}}{d\lambda^{2}}=\frac{A\cdot\cos(\varepsilon/2-\Phi_{1})}{d}\cdot\frac{d^{2}P_{PR}}{d\lambda^{2}}, \tag*{(16)}
d2PCOMPdλ2=−l⋅{sin⁡ΔΦ2⋅[d2nPRdλ2(−dΦ2dnPR)+(dnPRdλ)2⋅(−d2Φ2dnPR2)]+cos⁡ΔΦ2⋅(dnPRdλ)2⋅(−dΦ2dnPR)},(17)\frac{d^{2}P_{COMP}}{d\lambda^{2}}=-l\cdot\left\{\sin\Delta\Phi_{2}\cdot\left[\frac{d^{2}n_{PR}}{d\lambda^{2}}\left(-\frac{d\Phi_{2}}{dn_{PR}}\right)+\left(\frac{dn_{PR}}{d\lambda}\right)^{2}\cdot\left(-\frac{d^{2}\Phi_{2}}{dn_{PR}^{2}}\right)\right]+\cos\Delta\Phi_{2}\cdot\left(\frac{dn_{PR}}{d\lambda}\right)^{2}\cdot\left(-\frac{d\Phi_{2}}{dn_{PR}}\right)\right\}, \tag*{(17)}

where tt is the width of the crystal, dd is the diameter of the laser beam when fully inserted into the prisms, AA is the total depth of excessive insertion of the prisms into the laser beam (Figure 2), dnCRdλ\frac{dn_{CR}}{d\lambda} is calculated using Eq. (2), substituting n0CRn_{0CR} obtained from Eq. (1) in place of n0n_{0}, and using values of BjB_j and λj\lambda_j for Ti:Al2_2O3_3 from Table I. Similarly, d2nCRdλ2\frac{d^{2}n_{CR}}{d\lambda^{2}} is calculated from Eq. (3).

By substituting Eq. (14)–(17) into (13), one can determine the distance ll between prisms (Figure 2) required for full compensation of GDD arising both in the crystal and in the prisms:

l=d2PCRdλ2+d2PPRdλ2+d2PADD-PRdλ2sin⁡ΔΦ2⋅[d2nPRdλ2(−dΦ2dnPR)+(dnPRdλ)2⋅(−d2Φ2dnPR2)]+cos⁡ΔΦ2⋅(dnPRdλ)2⋅(−dΦ2dnPR).(18)l=\frac{\frac{d^{2}P_{CR}}{d\lambda^{2}}+\frac{d^{2}P_{PR}}{d\lambda^{2}}+\frac{d^{2}P_{ADD\text{-}PR}}{d\lambda^{2}}}{\sin\Delta\Phi_{2}\cdot\left[\frac{d^{2}n_{PR}}{d\lambda^{2}}\left(-\frac{d\Phi_{2}}{dn_{PR}}\right)+\left(\frac{dn_{PR}}{d\lambda}\right)^{2}\cdot\left(-\frac{d^{2}\Phi_{2}}{dn_{PR}^{2}}\right)\right]+\cos\Delta\Phi_{2}\cdot\left(\frac{dn_{PR}}{d\lambda}\right)^{2}\cdot\left(-\frac{d\Phi_{2}}{dn_{PR}}\right)}. \tag*{(18)}

Excessive insertion of the prisms effectively increases the laser beam diameter, which is accounted for in Eq. (15). This conditional beam expansion is described by Eq. (16) as A⋅cos⁡(ε/2−Φ1)A\cdot\cos(\varepsilon/2-\Phi_{1}) and is determined using the sine theorem. By substituting Eq. (14)–(17) into (13), one can also find the total depth of excessive prism insertion at a known distance between prisms:

A=−d⋅(d2PCRdλ2+d2PPRdλ2+d2PCOMPdλ2)cos⁡(ε/2−Φ1)⋅d2PPRdλ2.(19)A=\frac{-d\cdot\left(\frac{d^{2}P_{CR}}{d\lambda^{2}}+\frac{d^{2}P_{PR}}{d\lambda^{2}}+\frac{d^{2}P_{COMP}}{d\lambda^{2}}\right)}{\cos(\varepsilon/2-\Phi_{1})\cdot\frac{d^{2}P_{PR}}{d\lambda^{2}}}. \tag*{(19)}

From Eq. (19), one can construct the dependence of the excessive prism insertion depth AA on the distance ll between prisms (Figure 3) for the case λ0=800\lambda_{0}=800 nm, Δλ=20\Delta\lambda=20 nm, t=4.5t=4.5 mm, d=2d=2 mm.

Dependence of excessive prism insertion on the distance between prisms

Figure 3. Dependence of excessive prism insertion AA on the distance ll between prisms.

For the given parameters, the minimum distance between prisms ensuring full GDD compensation without excessive insertion is 369 mm (see Figure 3). At shorter distances, the prisms must be partially withdrawn from the beam (reducing dd), resulting in power loss. This means the value of ll at A=0A=0 represents the minimum permissible distance. When ll is more than 369 mm, excessive insertion of the prisms into the beam is required.

THE INFLUENCE OF PRISM CONFIGURATION ON LASER RADIATION PARAMETERS

In our physical experiments, the distance between the prisms is fixed at approximately 610 mm, and changing this distance proved to be quite labor-intensive. At the same time, the depth of excessive insertion of the second prism into the laser beam could be easily adjusted within the range of 0 to 4 mm. Therefore, preliminary calculations were performed for the case of a fixed distance between prisms and variable depth of second prism insertion.

Photograph of a prism inserted into a laser beam is shown in Figure 4.

Photograph of a prism inserted into a laser beam

Figure 4. Photograph of a prism inserted into a laser beam (1).

Our femtosecond laser system is capable of generating pulses with sufficient power for the planned dielectric laser acceleration (DLA) experiments within a central wavelength range of 780 nm to 860 nm and a spectral bandwidth range of 10 nm to 90 nm. As follows from Eq. (13), at certain values of AA and ll, by reconfiguring the resonator elements, it is possible to achieve mode-locking and obtain radiation spectra with different combinations of central wavelength λ0\lambda_0 and spectral bandwidth Δλ\Delta\lambda on the curves shown in Figure 5.

Calculated possible combinations of central wavelength and spectral bandwidth

Figure 5. Calculated possible combinations of Δλ\Delta\lambda and λ0\lambda_0 in the mode-locking regime for l=610l = 610 mm and different values of AA: 3.07 mm (1), 3.16 mm (2), 3.38 mm (3), 3.6 mm (4). Numbers 1–4 correspond to the experimental data in Figure 6.

With a distance between prisms of 610 mm, we were able to achieve mode-locking at various combinations of central wavelength and spectral width in our physics experiments (Figure 6, Table II), which confirms the validity of our preliminary calculations (Figure 5).

Experimental radiation spectrum in the mode-locking regime

Figure 6. Experimental radiation spectrum in the mode-locking regime for different values of AA: 3.07 mm (1), 3.16 mm (2), 3.38 mm (3), 3.6 mm (4).

Exact real combinations of Δλ\Delta\lambda and λ0\lambda_0 realized in practice depend on the alignment of the optical components in the laser resonator, particularly on the Brewster angle settings and the aperture tuning in the optical setup.

The excessive prism insertion depth AACentral wavelength of radiation λ0\lambda_0Spectral width of radiation Δλ\Delta\lambda (at half-maximum)
3.07 mm808 nm37.5 nm
3.16 mm830 nm29.0 nm
3.38 mm850 nm27.5 nm
3.60 mm835 nm56.5 nm

Table 2. Experimental radiation spectral data in the mode-locking regime

CALCULATIONS OF GDD USING GEOMETRIC MODELING

The accuracy of the calculated GDD parameters, obtained using the presented physical model, was further verified by means of geometrical modeling.

As an example, the following parameters were considered: central wavelength of radiation λ0=800\lambda_0 = 800 nm, spectral width Δλ=20\Delta\lambda= 20 nm, the width of the crystal t=4.5t = 4.5 mm, the diameter of the laser beam d=2d = 2 mm, and the excessive prism insertion depth A=2.8A = 2.8 mm. For the lower edge of the laser beam, the trajectories of the extreme spectral components with wavelengths of 790 nm and 810 nm were constructed (Figure 7). The refraction angles at the interfaces between different media were calculated using Snell’s law for each wavelength.

Geometric modeling of GDD compensation using a two-prism system

Figure 7. Geometric modeling of GDD compensation using a two-prism system with a distance between prisms ll. Dashed lines indicate ray path prior to additional insertion of the second prism by depth AA.

To fully compensate GDD the optical paths PP of all spectral components within the laser resonator should be equal to each other [9]:

P1=P2=…=Pi,(20)P_1 = P_2 = \ldots= P_i, \tag*{(20)}
Pi=LCR(λi)⋅(nCR(λi)−λi⋅dnCR(λi)dλi)+LCR−PR1(λi)+LPR1(λi)⋅(nPR(λi)−λi⋅dnPR(λi)dλi)+LPR1−PR2(λi)+LPR2(λi)⋅(nPR(λi)−λi⋅dnPR(λi)dλi)+LPR2−MIR(λi),(21)\begin{aligned} P_i ={}& L_{CR}(\lambda_i)\cdot\left(n_{CR}(\lambda_i)-\lambda_i\cdot\frac{dn_{CR}(\lambda_i)}{d\lambda_i}\right) + L_{CR-PR1}(\lambda_i)\\ &+L_{PR1}(\lambda_i)\cdot\left(n_{PR}(\lambda_i)-\lambda_i\cdot\frac{dn_{PR}(\lambda_i)}{d\lambda_i}\right) + L_{PR1-PR2}(\lambda_i)\\ &+L_{PR2}(\lambda_i)\cdot\left(n_{PR}(\lambda_i)-\lambda_i\cdot\frac{dn_{PR}(\lambda_i)}{d\lambda_i}\right) + L_{PR2-MIR}(\lambda_i), \tag*{(21)} \end{aligned}

where L(λi)L(\lambda_i) is the geometric path length of a spectral component with wavelength λi\lambda_i on each straight section (see Figure 7): between optical elements (LCR−PR1(λi)L_{CR-PR1}(\lambda_i), LPR1−PR2(λi)L_{PR1-PR2}(\lambda_i), LPR2−MIR(λi)L_{PR2-MIR}(\lambda_i)), within a laser crystal (LCR(λi)L_{CR}(\lambda_i)) and within prisms (LPR1(λi)L_{PR1}(\lambda_i), LPR2(λi)L_{PR2}(\lambda_i)). Refractive indices n(λi)n(\lambda_i) of crystal (nCR(λi)n_{CR}(\lambda_i)) and prisms (nPR(λi)n_{PR}(\lambda_i)) were determined using Eq. (1). The values of dn(λi)dλi\frac{dn(\lambda_i)}{d\lambda_i} were calculated for crystal and prism by the formula:

dn(λi)dλi=−λin(λi)⋅∑j=13λj2⋅Bj(λi2−λj2)2,(22)\frac{dn(\lambda_i)}{d\lambda_i}=-\frac{\lambda_i}{n(\lambda_i)}\cdot\sum_{j=1}^{3}\frac{\lambda_j^2\cdot B_j}{(\lambda_i^2-\lambda_j^2)^2}, \tag*{(22)}

where the coefficients BjB_j and λj\lambda_j correspond to the material parameters listed in Table I.

The optical path difference between the spectral components at 790 nm and 810 nm within the resonator equaled zero for a distance between prisms l=608l = 608 mm, whereas the value calculated analytically using Eq. (18) was l=615l = 615 mm. Thus, the discrepancy between the mathematically calculated distance between prisms and the value obtained through geometrical modeling amounted to only 1.1 %, which confirms the validity of the proposed approach. Modeling confirmed the accuracy of the analytical calculations, with a discrepancy of less than 1.1 %. These findings offer a practical basis for optimizing dispersion compensation parameters to ensure stable generation of ultrashort pulses, which are essential for the implementation of dielectric laser acceleration (DLA) experiments.

CONCLUSIONS

In summary, this study presents a comprehensive theoretical and experimental analysis of how the configuration of the prism compressor affects the output parameters of a femtosecond laser system. The developed mathematical model enables precise calculation of the conditions required for mode-locking at specific central wavelengths and spectral widths. The results of geometrical modeling confirmed the accuracy of the analytical calculations, with a discrepancy of less than 1.1 %. These findings offer a practical basis for optimizing dispersion compensation parameters to ensure stable generation of ultrashort pulses, which are essential for the implementation of dielectric laser acceleration (DLA) experiments.

Acknowledgments

The study is supported by the National Research Foundation of Ukraine under the program ”Excellent Science in Ukraine” (project # 2023.03/0182).

References

References

  1. [1]W. Sibbett, A.A. Lagatsky, T.A. Brown. The development and application of femtosecond laser systems // Optics Express. 2012, v. 20, № 7, p. 6997–6999. https://doi.org/10.1364/OE.20.006989
  2. [2]G.V. Sotnikov, A.V. Vasiliev, I.V. Beznosenko, S.M. Kovalov, A.I. Povrozin, O.O. Svystunov. Comparative analysis of electron acceleration by laser pulse in flat and grating dielectric structures // Nuclear Instruments and Methods in Physics Research A: Accelerators, Spectrometers, Detectors and Associated Equipment. 2025, v. 1072, № 170158, p. 1. https://doi.org/10.1016/j.nima.2024.170158
  3. [3]A.V. Vasiliev, A.I. Povrozin, G.V. Sotnikov. General solution of the excitation problem of a symmetric flat dielectric structure by plane electromagnetic waves // Problems of Atomic Science and Technology. 2023, v. 145, № 3, p. 99–102. https://doi.org/10.46813/2023-145-099
  4. [4]D. E. Spence, P. N. Kean, W. Sibbett. 60-fsec pulse generation from a self-mode-locked Ti:sapphire laser // Opt. Lett. 1991, v. 16, № 1, p. 42–44. https://doi.org/10.1364/OL.16.000042
  5. [5]H. A. Haus. Theory of mode locking with a fast saturable absorber // J. Appl. Phys. 1975, v. 46, № 7, p. 3049–3058. https://doi.org/10.1063/1.321997
  6. [6]R.L. Fork, O.E. Martinez, J.P. Gordon. Negative dispersion using pairs of prisms // Opt. Lett. 1984, v. 9, № 5, p. 150–152. https://doi.org/10.1364/OL.9.000150
  7. [7]V.P. Zaitsev, V.P. Leshchenko, A.I. Povrozin. Calculation of group velocity dispersion prism compensator for femtosecond lasers // Problems of Atomic Science and Technology. 2010, v. 54, № 3, p. 107–110. https://vant.kiпt.kharkov.ua/ARTICLE/VANT_2010_3/article_2010_3_107.pdf
  8. [8]A.V. Vasiliev, A.N. Dovbnya, A.M. Yegorov, V.P. Zaitsev, V.P. Leshchenko, I.N. Onischenko, A.I. Povrozin, G.V. Sotnikov. Works in the NSC KIPT on the creation and application of the CPA laser system // Problems of Atomic Science and Technology. 2018, v. 116, № 4, p. 289–293. https://vant.kiпt.kharkov.ua/ARTICLE/VANT_2018_4/article_2018_4_289.pdf
  9. [9]D. Marcuse. Pulse distortion in single-mode fibers // Applied Optics. 1980, v. 19, № 10, p. 1653–1660. https://doi.org/10.1364/AO.19.001653
  10. [10]M. J. Dodge. ”Refractive Index” in Handbook of Laser Science and Technology, v. 4: Optical Materials, part 2. Boca Raton: ”CRC Press”, 1986, p. 30.
  11. [11]C. Z. Tan. Determination of refractive index of silica glass for infrared wavelengths by IR spectroscopy // J. Non-Cryst. Solids. 1998, v. 223, № 1–2, p. 158–163. https://doi.org/10.1016/S0022-3093(97)00438-9

Paper details

vlnc:W_6csjdyzp
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents