betaFeedback

WorksPhysics and Astronomy

Amplitude-conserving frequency demultiplexer based on a spin wave delay line

Abstract

Propagating spin waves have emerged as promising candidates for signal processing and information transmission. We present a theoretical investigation of the generation, propagation and collection of spin-wave wave packets in micrometer-wide magnetic conduits, highlighting their potential for analogue frequency demultiplexing in space and time. We clarify the roles of the excitation duration and of the spin wave dispersion relation, as well as the influence of the spin-wave linewidth in setting the spatio-temporal evolution of propagating spin-wave wavepackets excited by Gaussian field pulses. We issue rules for the spatio-temporal separation of wavepackets that carry different frequencies. We finally propose an amplitude-conserving frequency demultiplexer based on a spin wave delay line of 60x5 μμm2^2 footprint.

Introduction

Communication systems require efficient separation of complex multi-tone signals for multichannel processing. This demultiplexing operation can in principle be achieved by exploiting ensembles of frequency carriers—waves—that propagate with contrasting group velocities and therefore may separate in space-time. Magnonics is promising platform for this purpose [1]. Spin waves (SWs) are, indeed, ideally suited as they combine microwave frequency operation and kk-dependent group velocity that can be tuned by material and geometry. Narrow spin-wave conduits are particularly attractive as confinement effects lead to the appearance of well-defined modes [2] with strongly contrasting dispersive characters [3, 4]. Harnessing these modes for spin-wave-based demultiplexing operations requires to understand the dynamics of spin-wave wave packets—an aspect that remains relatively sparsely explored in the community [5, 6, 7, 8, 9]. The few demultiplexing operations harnessing SWs implemented so far either required an active current supply [10] or used complex geometries [11, 12].

In this work, we investigate the evolution of SW wave packets upon their propagation. We evidence that wave packets carrying different frequencies separate linearly with the travelled distance rr while they broaden only as r\sqrt{r} at large rr, such that they can be separated by propagation. This is the key property that we shall use for demultiplexing purposes. Our approach uses the frequency dependence of the group velocity in a single waveguide, so that the frequencies are separated in time and position by a passive and easy to fabricate device without requiring complex structures or control currents.

This paper is organized as follows. After describing the system and the dispersion relations of its relevant SW modes, we compute the frequency dependence of SW-based energy transmission between distant antennas and the corresponding impulse response. Next, we study the spatio-temporal evolution of SW wavepackets of central frequency ω0\omega_0 and analyse the respective influences of the group delay (τg\tau_g), the group-delay dispersion (τD\tau_D) and the excitation duration (τ0\tau_0). We finally show that frequency demultiplexing can be obtained by a proper engineering of the SW conduit and of the antennas.

Material and geometry

We harness the propagation of SW wavepackets along a straight magnetic conduit of thickness tmag=60t_\mathrm{mag}=60 nm and width wmag=5 μmw_\mathrm{mag}=5\ \mu\mathrm{m} (Figure 1a) made from a CoFeB alloy of magnetization Ms=1340 kA.m−1M_s=1340\ \mathrm{kA.m}^{-1} and damping α=0.004\alpha=0.004. CoFeB is particularly well suited for device implementation as its high Curie temperature ensures robustness of its properties against temperature variations. We apply a field μ0Hy=35\mu_0H_y=35 mT in the width direction (i.e. yy), leading the magnetization configuration depicted in Figure 1b. The magnetization is aligned with the field in the 3 μm3\ \mu\mathrm{m}-wide central region of the conduit but the edges remain unsaturated. SEE FOOTNOTE AND ADD REF[14]. Above the conduit, we consider two identical antennas separated by a center-to-center distance rr, meant to excite and detect SWs with kxk_x the component of their SW wavevectors along the conduit. We thus consider the so-called ”Damon–Eshbach” configuration [15]. In addition to the propagating character along the conduit length, its finite width is known to lead to some lateral confinement of the SWs. The SWs exhibit consequently a standing wave character in the y⃗\vec{y} direction [2]. For tmag≪wmagt_\mathrm{mag}\ll w_\mathrm{mag} the standing wave character is well described by counter-propagating waves of wavevectors ky≈±nπweffk_y\approx\pm\frac{n\pi}{w_\mathrm{eff}}, where nn is the number of anti-nodes of the mode and weffw_\mathrm{eff} is an effective width corresponding to the saturated area (Figure 1b).

Figure 1. Spin-wave properties and response: simulation and analytical modelling of a 5 µm wide waveguide of 60-nm-thick CoFeB. (a) Sketch of the setup of propagating spin wave spectroscopy (PSWS, [13]) (b) Configuration of the equilibrium magnetization (bottom-half) and dynamic magnetizations of the lowest frequency SWs (top-half) for an applied field of 35 mT (c) Map of SWs normalized susceptibility excited by a 500 nm wide antenna RF field. The white circles mark the positions of maximum spectral intensity. The red line shows a fit of the analytical spin-wave dispersion relation for the fundamental mode (n=1n = 1). (d) and (e) are the simulated mode profiles of width mode and edges modes respectively. (f) Analytical group velocity of SWs under various internal fields H0H_0. (g) Numerical calculation of PSWS response S~21(ω,r=60 μm)\widetilde{S}_{21}(\omega, r = 60\,\mu\mathrm{m}) excited by a 100 nm width antenna. The internal field is μ0H0=20\mu_0 H_0 = 20 mT. (h) Impulse response corresponding to the previous S~21(ω,r=60 μm)\widetilde{S}_{21}(\omega, r = 60\,\mu\mathrm{m}) of Fig.1.g.

Spin waves properties in the frequency domain

Exact dispersion relation

The dispersion relations ω(kx)\omega(k_x) of the set of SWs will be the cornerstone of our study. We first calculate them from micromagnetic simulations using the TetraX package [16]. Figure 1(c) reports the normalized microwave absorption of the conduit when submitted to the microwave field generated by a 500 nm wide antenna placed at 100 nm above the SW conduit. The microwave absorption mostly arises from two modes: a mode at 2.5 GHz with a flat dispersion relation and a high frequency one at 5.1 GHz with a ∨\vee-shaped dispersion relation.

Their spatial profiles for kx=0k_x = 0 are depicted in Figure 1(d,Figure 1e), which reports cross sections of the dynamical magnetization component mxm_x. The high-frequency mode (Figure 1(d)) has the profile expected for a width mode indexed with n=1n = 1. In contrast the low-frequency mode is an edge mode, with amplitude being finite solely in two symmetric narrow regions within the edge domains. [Figure 1.e]. While this edge mode is excitable by the antenna, its flat dispersion results in a low group velocity such that this mode cannot transport energy over long distances. From now on, we shall therefore only consider the high-frequency (i.e. n=1n = 1) mode. As it is convenient to have an analytical description of the dispersion of this mode, we now compare the results of TetraX to the approximate expressions of Kalinikos and Slavin [17].

Approximative analytical dispersion relation

For a transversally magnetized stripe, the dispersion relation of the n=1n = 1 mode can be approximated by [3]:

ω(kx)=γ0(H0+Ms(1−P))(H0+MsPkx2k2)(1)\omega(k_x) = \gamma_0 \sqrt{\left(H_0 + M_s(1-P)\right)\left(H_0 + M_s P \frac{k_x^2}{k^2}\right)} \tag*{(1)}

where P=1+e−ktmag−1ktmagP = 1 + \frac{e^{-k t_{\mathrm{mag}}}-1}{k t_{\mathrm{mag}}}, k2=kx2+π2weff2k^2 = k_x^2 + \frac{\pi^2}{w_{\mathrm{eff}}^2}, γ0/(2π)=29.3\gamma_0/(2\pi) = 29.3 GHz/T the gyromagnetic ratio and H0H_0 accounts for the adequately averaged internal magnetic field. The effective demagnetizing correction can be found using a fit [red line in Figure 1(c)] of the TetraX dispersion relation with Eq. (1), which yields μ0H0=20\mu_0 H_0 = 20 mT <μ0Hy=35< \mu_0 H_y = 35 mT. The frequency linewidth Δω0\Delta\omega_0 is: (see Supplemental Material, section II),

Δω0(kx,ky)=αγ0(2H0+Ms(1−kx2kx2+ky2P)).(2)\Delta\omega_0(k_x,k_y) = \alpha\gamma_0 \left(2H_0 + M_s\left(1-\frac{k_x^2}{k_x^2+k_y^2}P\right)\right). \tag*{(2)}

Since Ms≫H0M_s \gg H_0, PMsP M_s the linewidth is almost wavevector independent. We will consider it to be constant.

The approximate dispersion relation (Eq. (1)) was confirmed to work in the ranges of wavevectors and fields to be used in this paper. Figure 1(f) displays the corresponding field and frequency dependences of the group velocity vgv_g. Increasing the field increases the frequency gap while essentially preserving the overall SW propagation metrics. The vg(f)v_g(f) curves differ only at low frequencies where the vgv_g’s systematically peak, reaching for instance 30 km/s for μ0H0=20\mu_0 H_0 = 20 mT at the inflexion point of the dispersion relation at 7 GHz. We will use the strong variation of the vg(f)v_g(f) with the frequency for the space-time separation of wavepackets.

Characteristic times and lengths of spin wave propagation

Prior to modelling the propagation of SW wavepackets, it is worth defining the three characteristic times involved in the problem.

(i) The first one is the initial duration τ0\tau_0 of a wavepacket of central frequency ω0/(2π)\omega_0/(2\pi), to be defined in section IV B.

The two other characteristic times are defined by expanding the dispersion relation and considering the propagation of a SW over a distance r≥0r \ge0.

(ii) The arrival time τg\tau_g of the wavepacket is the group delay:

τg(ω0,r)=rdkx(ω)dω∣ω=ω0=rvg(ω0).(3)\tau_g(\omega_0,r) = r\left.\frac{d k_x(\omega)}{d\omega}\right|_{\omega=\omega_0} = \frac{r}{v_g(\omega_0)}. \tag*{(3)}

which expresses the spatio-temporal drift of the centre of the wavepacket at the group velocity vg(ω0)v_g(\omega_0).

(iii) The third characteristic time of the problem is the group-delay dispersion τD(ω0,r)\tau_D(\omega_0,r) (GDD) defined from the curvature of the dispersion relation:

τD2(ω0,r)=rd2kx(ω)dω2∣ω=ω0.(4)\tau_D^2(\omega_0,r) = r\left.\frac{d^2 k_x(\omega)}{d\omega^2}\right|_{\omega=\omega_0}. \tag*{(4)}

τD2\tau_D^2 characterizes the progressive evolution of a wavepacket upon its spatio-temporal propagation. The first meaning of τD2\tau_D^2 can be understood from dimensional analysis: it is the square of a time, or equivalently, a time divided by a frequency. Qualitatively, ∣τD2∣\lvert\tau_D^2\rvert parametrises the increase of a pulse duration (typically in added nanoseconds) that a pulse of given frequency width (typically in GHz) undergoes after having propagated over a distance rr. The second meaning of τD2\tau_D^2 resides in its sign. It is negative (positive) when the high-frequency components propagate faster (slower) than low-frequency components. As a result, the wavepackets progressively distorts (it “chirps”). For τD2<0\tau_D^2 < 0 the low frequency components progressively gather near the trailing edge of the wavepacket, while the high frequency ones group at the leading edge of the wavepacket.

The interest of defining τg\tau_g and τD\tau_D is evident when considering a narrow band wavepacket of central frequency ω0\omega_0 and central wavevector k0(ω0)k_0(\omega_0). When travelling a distance rr, each frequency component of this wavepacket acquires a phase shift ϕ(ω)=k r\phi(\omega)=k\,r, that can be expressed to second order in δω=ω−ω0\delta\omega=\omega-\omega_0 as:

ϕ(ω)=ϕ0+τg(ω0,r) δω+12τD2(ω0,r) δω2+O(δω3).(5)\phi(\omega)=\phi_0+\tau_g(\omega_0,r)\,\delta\omega+\frac{1}{2}\tau_D^2(\omega_0,r)\,\delta\omega^2+O(\delta\omega^3). \tag*{(5)}

The last important metrics is the attenuation length of the SWs Latt=2vgΔω0L_{\mathrm{att}}=\frac{2v_g}{\Delta\omega_0} [18].

It is worth giving order-of-magnitudes, for instance r=60r=60 μ\mum and μ0H0=20\mu_0H_0=20 mT. A wavepacket central frequency ω0/2π=10\omega_0/2\pi=10 GHz yields τg=3\tau_g=3 ns and τD2=(0.26\tau_D^2=(0.26 ns)2)^2. Comparatively, the SWs are faster for ω0/2π=6.6\omega_0/2\pi=6.6 GHz since the arrival time is decreased to τg=2\tau_g=2 ns. Besides the SWs are substantially less dispersive at this frequency, the dispersion delay is strongly reduced to τD2=−(0.08\tau_D^2=-(0.08 ns)2)^2. The mode linewidth is 0.19 GHz. This leads to an attenuation length of 48 μ\mum at kx=0.5k_x=0.5 rad/μ\mum and 5.5 μ\mum at 10 rad/μ\mum.

Antenna-to-antenna transmission spectrum

Let us now calculate the transmission S~21(ω,r)\tilde{S}_{21}(\omega,r) between two antennas. The transmission refers to the complex inductive voltage induced in the receiving antenna (P2) when the input antenna (P1) is driven by an RF current at frequency ω\omega. Following Eq. (18) of Ref. [19] and considering only the in-plane component of the antenna field, it is:

S~21(ω,r)=∫−∞∞χxx(kx,ω)e−ikxrh~rf(kx)2 dkx.(6)\tilde{S}_{21}(\omega,r)=\int_{-\infty}^{\infty}\chi^{xx}(k_x,\omega)e^{-ik_xr}\tilde{h}_{rf}(k_x)^2\,dk_x. \tag*{(6)}

where h~rf(kx)2=h~rfP1(kx)h~rfP2,∗(kx)\tilde{h}_{rf}(k_x)^2=\tilde{h}_{rf}^{P1}(k_x)\tilde{h}_{rf}^{P2,*}(k_x) is the product of the efficiency functions of antenna P1 and the complex conjugate of that of antenna P2, describing the SW wavevectors that can couple inductively to the antennas (See Eq. 6 of ref. [19]). For a thin single (S) wire antenna of width L1L_1 directly deposited above the magnetic material, the antenna function is the real-valued function:

hrfS(kx)∝sinc⁡(kL12).(7)h_{rf}^{S}(k_x)\propto\operatorname{sinc}\left(\frac{kL_1}{2}\right). \tag*{(7)}

χxx(kx,ω)\chi^{xx}(k_x,\omega) is the transverse susceptibility. In the low damping regime where α≪1\alpha\ll1 it is (see Supplemental Material, section II):

χxx(kx,ω)=ωmax⁡(kx)2ωk(kx)2−ω2−iωΔω(kx)(8)\chi^{xx}(k_x,\omega)=\frac{\omega_{\max}(k_x)^2}{\omega_k(k_x)^2-\omega^2-i\omega\Delta\omega(k_x)} \tag*{(8)}

where ωk(kx)\omega_k(k_x) is the SW dispersion relation, Δω(kx)\Delta\omega(k_x) the SW linewidth and ωmax⁡(k)2\omega_{\max}(k)^2 is γ02Ms(H0+Ms(1−P))\gamma_0^2M_s(H_0+M_s(1-P)). An example of susceptibility spectrum is plotted in Figure 2c.

Figure 2. Applied microwave field pulse in time- and frequency-domains, and magnetic susceptibility. (a) 12 GHz Gaussian pulse of duration of τ0=0.5\tau_0=0.5 ns or equivalently a full width at half maximum τ0FWHM=1.17\tau_0^{\mathrm{FWHM}}=1.17 ns. (b) Frequency spectrum of the excitation. (c) Magnetic susceptibility for mode linewidths Δω0=(2π)×200\Delta\omega_0=(2\pi)\times200 MHz and wavevector k0=2k_0=2 rad/μ\mum.

Figure 1g shows the calculated [20] spectrum of the antenna-to-antenna transmission for μ0Hy=20\mu_0H_y=20 mT, 100 nm-wide antennas and r=60r=60 μ\mum. The transmission is allowed above the SW gap at 5.1 GHz and consists of a phase-rotating factor with an envelope that decreases with frequency and extends up to circa 16 GHz.

The transmission response to any stimulus of spectrum G~(ω)\tilde{G}(\omega) can be obtained by multiplying it with the transfer function:

S~out(ω,r)=S~21(ω,r)G~(ω).(9)\tilde{S}_{\mathrm{out}}(\omega,r)=\tilde{S}_{21}(\omega,r)\tilde{G}(\omega). \tag*{(9)}

The corresponding time-domain response is the convolution of the input signal with the system’s impulse response, or equivalently the Fourier transform of Eq. (9).

Spin waves properties in the time domain

Antenna-to-antenna impulse response

S~21(ω,r)\tilde{S}_{21}(\omega,r) can be transformed to describe the impulse response, i.e. the time-domain response at the output antenna to a Dirac field pulse applied at the input antenna [6]. Figure 1g displays such impulse response. As expected for r=60r=60 μ\mum and vgmax⁡≈30v_g^{\max}\approx30 km/s the first SWs arrive at r/vg≈2r/v_g\approx2 ns. The contribution from the slower SWs is present at larger arrival times, typically up to 6 ns. This distribution of arrival times stems from the frequency dependence of group velocity. This opens the possibility to separate in time and space the different frequency contributions inside a complex signal. As a first case study, let us analyse the response to a short burst of SWs.

Defining a Gaussian pulse

We consider a pulsed input field g(t)g(t) of Gaussian envelope, amplitude E0E_0, root mean square (RMS) duration τ0\tau_0, which means a pulse ”duration” (full width at half maximum of the envelope) being τ0FWHM≈2.35τ0\tau_0^{\mathrm{FWHM}}\approx2.35\tau_0. It reads:

g(t)=E0e−t22τ02cos⁡(ω0t).(10)g(t)=E_0e^{-\frac{t^2}{2\tau_0^2}}\cos(\omega_0t). \tag*{(10)}

The associated spectrum G~(ω)\tilde{G}(\omega) is real-valued consists of two Gaussian functions centred at ±ω0\pm\omega_0:

G~(ω)=E0τ02[e−τ022(ω−ω0)2+e−τ022(ω+ω0)2]∈R.(11)\tilde{G}(\omega)=\frac{E_0\tau_0}{2}\left[e^{-\frac{\tau_0^2}{2}(\omega-\omega_0)^2}+e^{-\frac{\tau_0^2}{2}(\omega+\omega_0)^2}\right]\in\mathbb{R}. \tag*{(11)}

fig:2a and b respectively display the excitation pulse in time and frequency domains for f0=ω0(2π)−1=12f_0=\omega_0(2\pi)^{-1}=12 GHz and a pulse duration τ0FWHM=1.2\tau_0^{\mathrm{FWHM}}=1.2 ns.

Analytical approximate model for pulsed operation

Let us calculate the response of the SW system to this Gaussian pulse. An analytical approximation can be derived under the assumptions that (i) the dispersion relation is a parabola [21], (ii) the antenna is broadband in wavevector space, (iii) the material only responds to the in-plane (i.e. xx-) component of the antenna field [22].

Efficiency function of the broadband antenna

All along section V we shall consider the limit of an antenna of vanishing width and thickness, i.e. {want,p}→0\{w_{\mathrm{ant}},p\}\rightarrow0. In this limit, the antenna generates an infinitely localized field:

hrf(x,{want,p→0})=δ(x)(12)h_{\mathrm{rf}}(x,\{w_{\mathrm{ant}},p\rightarrow0\})=\delta(x) \tag*{(12)}

where δ(x)\delta(x) is the Dirac delta function. In reciprocal space, the antenna efficiency function is constant:

hrf(k,{want,p→0})=1.(13)h_{\mathrm{rf}}(k,\{w_{\mathrm{ant}},p\rightarrow0\})=1. \tag*{(13)}

In the analytical framework of the present section (V) we consider that the SW wavepacket is excited by an rf field of the form g(t)δ(x)g(t)\delta(x), i.e. a Gaussian-in-time and infinitely localized at the sole x=0x=0 position. This will be compared later to a realistic case.

Space-time evolution of a wavepacket

Since the rf pulse (Eq. 10 and 11) is centred about ω0\omega_0 it excites SWs mainly about k0k_0. By expanding the dispersion relation using Eqs. 5 and 9, we obtain a first-order description of the evolution of the wavepacket. At a time t>0t > 0 and at a distance rr from the antenna, the output signal is (see Supplemental Material, section III):

soutk0(r,t)∝L(∣r∣)B(t,r)C(r)cos⁡[φ(r,t)](14)s_{\mathrm{out}}^{k_0}(r,t) \propto L(|r|) B(t,r) C(r) \cos[\varphi(r,t)] \tag*{(14)}

where the first factor is a damping-induced propagation loss, the second factor describes the dispersion-induced broadening of the wavepacket, the third factor describes a dispersion-induced internal decoherence of the wavepacket, and the last factor describe the propagation of the phase front. Let us discuss these factors.

Amplitude loss due to Gilbert damping

The first factor in (14) is the classical propagation loss arising from the Gilbert damping, expressed as:

L(∣r∣)=e−∣r∣/Latt0(15)L(|r|) = e^{-|r|/L_{\mathrm{att}}^{0}} \tag*{(15)}

with Latt0=2vgΔω0L_{\mathrm{att}}^{0} = \frac{2v_g}{\Delta\omega_0} the attenuation length of the SW {k0,ω0}\{k_0,\omega_0\}.

Dispersion-induced broadening of the wavepacket

The second factor in (14) is:

B(t,r)=exp⁡(−τ022τout4(t−rvg0)2)(16)B(t,r) = \exp\left(-\frac{\tau_0^2}{2\tau_{\mathrm{out}}^4}\left(t-\frac{r}{v_g^0}\right)^2\right) \tag*{(16)}

It describes the temporal broadening of the wavepacket about its centre which drifts in time-space as r=vg0tr = v_g^0t according to the group delay. The temporal width of the wavepacket at a propagation distance rr is τout/τ0\tau_{\mathrm{out}}/\tau_0 with:

τout4(r)=τ04+τD4(r)∈R+.(17)\tau_{\mathrm{out}}^4(r) = \tau_0^4 + \tau_D^4(r) \in\mathbb{R}^{+}. \tag*{(17)}
Wavepacket decoherence

In (14) the temporal width τout4(r)\tau_{\mathrm{out}}^4(r) also affects the decoherence factor C(r)C(r). C(r)C(r) encodes how the amplitude of the wavepacket is decreased by destructive interferences between its different spectral components. It reads:

C(r)=E0πτ0[τout4(r)]1/4ωmax⁡2ω0vg.(18)C(r) = \frac{E_0\pi\tau_0}{[\tau_{\mathrm{out}}^4(r)]^{1/4}}\frac{\omega_{\max}^2}{\omega_0v_g}. \tag*{(18)}
Phase oscillation within the pulse envelope

Finally, the phasor term cos⁡[φ(r,t)]\cos[\varphi(r,t)] captures both the wave character of the carrier and the dispersion-induced phase chirp. It is given by:

φ(r,t)=(k0r−ω0t)+f(t,τ0,τvg,τD2)(19)\varphi(r,t) = (k_0r-\omega_0t) + f(t,\tau_0,\tau_{vg},\tau_D^2) \tag*{(19)}

The carrier term describes the wave character, with a phase front advancing at r=ω0t/k0r = \omega_0t/k_0. The other contribution has a marginal quantitative influence. It is discussed in the supplemental material. Overall, the shape of the wave-packet results from the interplay between the dispersion, the loss and the finite excitation duration, a behaviour that is characteristic of wave propagation in dispersive media [23].

Physically-instructive limits

It is instructive to examine two specific limits of (14): the time evolution right under the antenna, and the wave packet profile at time zero.

Time evolution of the wavepacket right below the input antenna

If the receiving antenna was at the same place as the input antenna (i.e. at r=0r = 0), the group-delay dispersion would vanish and (14) would reduce to

soutk0(t,r=0)∝−E0πe−t22τ02vgω0sin⁡(ω0t).(20)s_{\mathrm{out}}^{k_0}(t,r=0) \propto-\frac{E_0\pi e^{-\frac{t^2}{2\tau_0^2}}}{v_g\omega_0}\sin(\omega_0t). \tag*{(20)}

This resembles the excitation pulse of (10): it lasts τ0\tau_0 and carries a harmonic oscillation. This sinus-like response is in quadrature with the cosinus-like stimulus g(t)g(t). The quadrature relationship is as expected for a precessional response of the magnetization to a field.

One may be surprised not to find a factor like e−Δω0t/2e^{-\Delta\omega_0t/2} that would express some damping of the SWs within (20). This apparent absence of the role at damping is related to the propagating wave situation that suppresses any local memory. Indeed at any given time the SWs excited in the past at r=0r = 0 have propagated away and are not longer at this central position, such that their damping—though real—is irrelevant there.

Profile of the wavepacket at the time origin

The second instructive limit is the spatial profile of the wavepacket at t=0t = 0, which reads

soutk0(t=0,r)=C(r)e−∣r∣Latt0e−r22τout4vg2cos⁡[φ(r,0)].(21)s_{\mathrm{out}}^{k_0}(t=0,r) = C(r)e^{-\frac{|r|}{L_{\mathrm{att}}^0}}e^{-\frac{r^2}{2\tau_{\mathrm{out}}^4v_g^2}}\cos[\varphi(r,0)]. \tag*{(21)}

It is noticeable that while the excitation field pulse was infinitely localized (Eq. (12)), the response of the magnetization is not localized and has a finite spatial extension, a counter-intuitive result that deserves explanation.

This finite extension at t=0t = 0 results in fact from the propagation of the SWs that were generated in the past (recall that the stimulus pulse starts essentially at t≈−τ0t \approx-\tau_0, see Figure 2a). At t=0t = 0 these past SWs have propagated over a typical distance vgτ0v_g\tau_0 and, meanwhile, they have undergone a dispersion-induced broadening set by vgτDv_g\tau_D, both effects giving a finite spatial extension. These propagation and dispersion effects affecting the SWs created in the past are gathered in the τout\tau_{\mathrm{out}} (see its expression in eq. (17)) contribution inside eq. (21). Meanwhile, all these past SWs have suffered a dissipation-induced decay that can be seen in the exp⁡[∣r∣/Latt]\exp[|r|/L_{\mathrm{att}}] factor.

We note that the eqs. (20) and (21) are singular when the dispersion relation is flat (i.e. vg=0v_g = 0). This pathological situation is treated in the Supplemental Material.

Discussion of the time-space evolution of the wave packets

The space-time evolution of a wavepacket as modelled through Eq. (14) was derived under three simplifying assumptions that restrict its applicability. In this section we compare this previous analytical formulation with the exact result obtained by numerical integration of Eq. (9) and subsequent Fourier transformation.

Comparison between the exact result and the analytical approximation

The time-resolved transmitted voltages are calculated in Figure 3(a,Figure 3b) for antenna-to-antenna distances r1=20r_1 = 20 μ\mum and r2=60r_2 = 60 μ\mum, field pulse duration τ0=0.2\tau_0 = 0.2 ns, central frequency 10 GHz, stripe width 5 μ\mum, internal field μ0H0=20\mu_0H_0 = 20 mT and mode linewidth Δω0=(2π)×200\Delta\omega_0 = (2\pi) \times200 MHz. The panel (a) is the exact numerical integration [Eq. (9)] for a 100-nm-wide antenna. The panel (b) is the analytical estimate [Eq. (14)] that assumes an antenna of zero width [24].

Figure 3. Voltages expected at the receiving antenna arising for stimuli of durations τ0=0.2\tau_0 = 0.2 ns. (a): Numerical integration [Eq. (6) and 9]. Parameters: Wstripe=5W_{\mathrm{stripe}} = 5 μ\mum, want=100w_{\mathrm{ant}} = 100 nm, μ0H0=20\mu_0 H_0 = 20 mT and α=0.004\alpha= 0.004. The stimulus central frequency is 10 GHz. (b): Analytical evaluation using Eq. (14) for propagation distances 20 and 60 μ\mum. (c): Evaluation of ∥S21k0(t,r)∥\lVert S_{21}^{k_0}(t,r)\rVert for three wave packets as a function of propagation distances and times. The packets are generated from pulses of central frequencies 7, 10.5 and 15 GHz in the same material as (a) and (b) but with vanishing damping to illustrate the sole effect of dispersion.

Overall, the two models agree on the arrival times of the wavepackets, their temporal broadening, their attenuation and their phase oscillations. As expected for a 10 GHz input pulse, the travelling wavepackets exhibit time oscillations of pseudo-period 100 ps [Figure 3(a,Figure 3b)]. They arrive at the times that were formerly anticipated from the group delays, i.e. at t1≈1t_1 \approx1 ns for r1=20r_1 = 20 μ\mum and t2≈3t_2 \approx3 ns for r2=60r_2 = 60 μ\mum. The agreement between the analytical and numerical model is almost perfect: the full widths at half maximum (FWHM) of the wavepackets are strictly identical for both datasets. The arrival times also match: they are τgnum(20 μm)=2.95\tau_g^{\mathrm{num}}(20\ \mu\mathrm{m}) = 2.95 ns and τgnum(60 μm)=0.98\tau_g^{\mathrm{num}}(60\ \mu\mathrm{m}) = 0.98 ns and τgana(20 μm)=2.95\tau_g^{\mathrm{ana}}(20\ \mu\mathrm{m}) = 2.95 ns and τgana(60 μm)=1.01\tau_g^{\mathrm{ana}}(60\ \mu\mathrm{m}) = 1.01 ns.

The propagation loss is also visible as an amplitude decay from r1r_1 to r2r_2. The dispersion is clearly perceivable: the wavepackets have broadened compared to the initial width τ0FWHM=0.47\tau_0^{\mathrm{FWHM}} = 0.47 ns, with FWHM width being 0.54 ns for r1=20r_1 = 20 μ\mum and 0.96 ns for r2=60r_2 = 60 μ\mum. This illustrates the contribution of dispersion which increases with the propagation distance. We emphasize that a 100 nm wide antenna is small enough not to contribute to the chirp of the wavepacket. Indeed, a SW at 10 GHz, Figure 3(a,Figure 3b), corresponds to a wavevector of 1.4 rad/μ\mum, which leads to an excitation efficiency of sinc⁡(kwant/2)2=0.998\operatorname{sinc}(kw_{\mathrm{ant}}/2)^2 = 0.998, close to 1, i.e. the value for an antenna of vanishing width, Eq. (13). This result shows that the analytical formula, Eq. (14), provides a solid basis to obtain design rules for SW demultiplexing.

Space-time evolution of wavepackets in absence of dissipation

We conclude that Eq. (14) is sufficiently accurate to be used to illustrate how propagating wavepackets evolve along the magnetic stripe. Figure 3(c) plots several such ∣s21k0(t,r)/s21k0(0,0)∣\left|s_{21}^{k_0}(t,r)/s_{21}^{k_0}(0,0)\right|. The calculations are now done in the zero damping limit to visualize the sole influence of dispersion on the amplitude decay.

As expected, the arrival times scale with the propagation distance. The wavepackets broaden upon propagation as a result of dispersion: this spread of the pulse energy over a wider temporal window comes together with a reduction of the peak intensity. This broadening effect is more pronounced for the high frequencies due to the higher curvature of the dispersion relation (the higher ”dispersivity”). Noticeably, the rate of wavepacket broadening is slower than the rate of pulse separation. Figure 3(c) evidences that pulses of duration τ0=200\tau_0 = 200 ps carrying frequencies of 7, 10.5 and 15 GHz should be separable for sufficiently long travelling distances, at least according to the approximate analytical model.

Therefore, the wave-packet amplitude decreases during propagation because of dispersion-induced broadening. This effect is captured by C(r)C(r), which reduces the SW amplitude as the group-delay dispersion increases. This effect adds to the dissipation-induced decay and is non-negligible. The two contributions scale differently with the propagation distance rr, see Eq. (14). Table I, obtained for the parameters of Figure 3(c), shows that both contributions are comparable up to r≈40r \approx40 µm, while Gilbert damping dominates at larger distances.

rr [µm]Damping e−r/Latte^{-r/L_{\mathrm{att}}}Dispersion C(r)/C(0)C(r)/C(0)Combined
2078 %81 %63 %
4061 %65 %40 %
6047 %54 %25 %
8037 %47 %17 %
10029 %41 %12 %

Table I. Normalized SW amplitude as a function of the propagation distance rr, separating the contributions of dissipation-induced decay and dispersion-induced broadening.

Evolution of the wavepacket integrity upon propagation

The temporal spreading of wave packets depends on their initial excitation durations τ0\tau_0 and varies asymptotically like ∝r\propto\sqrt{r} for large propagation distances (see Eq. (17)). The increase of the wave packet duration can be measured by the ”integrity” figure of merit τ02/∥τout2∥∈[0,100%]\tau_0^2/\lVert\tau_{\mathrm{out}}^2\rVert\in[0, 100\%], formed the ratio between the input and output temporal widths of the wavepackets. Figure 4 reports

Figure 4. Temporal spreading τ02/∥τout2∥\tau_0^2/\lVert\tau_{\mathrm{out}}^2\rVert of spin-wave wave packets as a function of the excitation duration τ0\tau_0 and propagating distance. The parameters are similar to Figure 3.

a quantitative evaluation of this metric for the example of a 10 GHz pulse, now with dissipation accounted for.

For long pulses, the integrity of the wavepacket is maintained (i.e. τ0≈∣τout∣\tau_0 \approx|\tau_{\mathrm{out}}|, white area in Figure 4) up to large propagation distances. In contrast, for short pulses (τ0≪0.4\tau_0 \ll0.4 ns), the wavepacket rapidly broadens with the propagation distance (coloured areas in Figure 4). In this regime the output temporal width is no longer solely set by the excitation duration but rather more and more by the dispersive nature of the SWs as they propagate.

Frequency demultiplexing using spin waves

Criterion for the separability of wavepackets

To achieve proper wavepacket separation, the temporal spacing between the centers of two wavepackets Δτg(ω1,ω2)\Delta\tau_g(\omega_1,\omega_2) should be larger than the sum of their widths. This is written as:

∣Δτg(ω1,ω2)∣≥1.18τ0[∥τout2(ω1)∥+∥τout2(ω2)∥](22)\left|\Delta\tau_g(\omega_1,\omega_2)\right| \ge\frac{1.18}{\tau_0}\left[\left\lVert\tau_{\mathrm{out}}^2(\omega_1)\right\rVert+\left\lVert\tau_{\mathrm{out}}^2(\omega_2)\right\rVert\right] \tag*{(22)}

and this sets conditions on the frequencies f1f_1 and f2>f1f_2 > f_1. Note that the factor 1.18 corresponds to the half width at half maxima of the wavepackets. A larger factor leads to a more robust separation, at the cost of a lower spectral resolution (see Supplementary Material). Figure 5.a shows the minimum frequency spacing Δfmin⁡=(ω2−ω1)/(2π)\Delta f_{\min}=(\omega_2-\omega_1)/(2\pi) required to separate 300 ps-long wavepackets, as calculated using the analytical framework. For instance, a wave packet propagating over a distance r=60r = 60 µm carrying a frequency f1=11f_1 = 11 GHz can be separated from any other carrying f2>13f_2 > 13 GHz. Since the separability criterion (Eq. (22)) assumes an infinitely narrow antenna and a perfectly parabolic dispersion relation, we must validate it with the results of the full numerical integrations using Eq. (9).

Figure 5. Determination of the separable frequency pairs and demonstration of spatio-temporal demultiplexing. (a) Relation between propagation distance and minimum frequency spacing Δfmin⁡\Delta f_{\min} (Eq. (22)) required to separate two wavepackets for τ0=0.3\tau_0 = 0.3 ns. (b) Complex field pulse of duration τ0=0.3\tau_0 = 0.3 ns carrying the frequencies {f1,f2,f3}={7,11,14}\{f_1, f_2, f_3\} = \{7, 11, 14\} GHz. (c) Positive-frequency part of the corresponding spectrum. (d) Time-resolved voltage expected at a distance r=60r = 60 μ\mum for single-wire antennas (see their sketch in inset). The coloured backgrounds indicate the temporal gates used for time gating. (e) Power spectral density of these time gated signals.

Demonstration of the demultiplexing of three frequencies

From Figure 5.(a) we have identified {f1,f2,f3}={7,11,14}\{f_1, f_2, f_3\} = \{7, 11, 14\} GHz with respective wavevectors {k1,k2,k3}={0.53,1.62,2.95}\{k_1, k_2, k_3\} = \{0.53, 1.62, 2.95\} rad/μ\mum, as carriers that should be separable for a pulse duration of 300 ps and antennas of zero widths. This stems from their differing group velocities which are {vg1,vg2,vg3}={29.8,17.5,11.6}\{v_{g1}, v_{g2}, v_{g3}\} = \{29.8, 17.5, 11.6\} km/s. This section demonstrates this statement for antennas of widths 100 nm by fully accounting for dispersion and dissipation using exact integration (Eq. (9)). It is clear that near the group-velocity peak (∼\sim6–8 GHz), Δfmin⁡\Delta f_{\min} is

diverging, indicating that demultiplexing operations are not achievable for these frequencies.

Figure 5.(b,c) display the sum of the three field pulses in time and frequency domains, as applied on the first antenna. The goal is to separate the three pulses. Figure 5.(d) reports the signal expected on the receiving antenna placed at a distance r=60r = 60 μ\mum. Three successive wavepackets contribute to the signal. The first arriving wavepacket (t∈[0,2.7]t \in[0, 2.7] ns) corresponds to the SWs with the highest group velocities; this packet carries a pseudo-period corresponding to the lowest frequency component (f1=7f_1 = 7 GHz). The two subsequent wavepackets, observed in the 2.6–4.5 ns and 4.5–6.5 ns time intervals, display lower amplitudes and their pseudo-period correspond to excitation frequencies of 11 and 14 GHz, respectively. Temporal gates (shaded regions in Figure 5.d) can be applied to analyse the spectral contents of each wavepacket, displayed in Figure 5.e. The gated spectra confirm three wavepacket assignments to the three frequencies initially injected into the system. This demonstrates the demultiplexing of the three initially overlapping wave packets.

Antenna engineering for amplitude-conserving demultiplexing

The successive wavepackets have unfortunately different amplitudes, A1A_1, A2/A1=0.4A_2/A_1 = 0.4 and A3/A1=0.2A_3/A_1 = 0.2. This is arising since arriving later in time means a further amplitude decay through Gilbert damping and dispersion broadening.

This non-conservation of the amplitudes of the 3 stimuli is a clear drawback. Fortunately, it can be compensated by a proper design of the antennas, either by pre-accentuating the wavepackets at their generation and/or by enhancing their detection yield at the receiving an∣∣h~rfant1(ki)⋅h~rfant2(ki)∗∣∣∝(Ai)−1||\tilde{h}_{\mathrm{rf}}^{\mathrm{ant1}}(k_i)\cdot\tilde{h}_{\mathrm{rf}}^{\mathrm{ant2}}(k_i)^*|| \propto(A_i)^{-1} for i=1,2,3i=1,2,3

while maximizing ∣∣h~rf(k3)∣∣2||\tilde{h}_{\mathrm{rf}}(k_3)||^2. These three criteria cannot be jointly fulfilled with the single-wire antenna used so far, which has wantw_{\mathrm{ant}} as single design parameter.

The simplest design is to use a single wire antenna of small width L1L_1 as a broadband emitter and a ⊔-shaped antenna as a filtering receiver. The latter is formed by two wires of widths L1L_1 carrying opposite currents, placed at wire-to-wire center-to-center distance cc. Assuming infinitely thin antennas, the xx-component of the efficiency function becomes:

hrfS(kx)hrfS(kx)∗=sinc⁡2(kxL12)×sin⁡2(kxc2).(23)h_{\mathrm{rf}}^{\mathrm{S}}(k_x)h_{\mathrm{rf}}^{\mathrm{S}}(k_x)^*=\operatorname{sinc}^2\left(\frac{k_xL_1}{2}\right)\times\sin^2\left(\frac{k_xc}{2}\right). \tag*{(23)}

Using Eq. (23) we determine the pairs {L1,c}\{L_1,c\} that ensure the proper gradation of antenna efficiencies (eq. 23) at the wavevectors {k1,k2,k3}={0.53,1.62,2.95} rad/μm\{k_1,k_2,k_3\}=\{0.53,1.62,2.95\}\ \mathrm{rad}/\mu\mathrm{m} that correspond to our three frequencies {f1,f2,f3}={7,11,14} GHz\{f_1,f_2,f_3\}=\{7,11,14\}\ \mathrm{GHz}. These criteria are reasonably satisfied for the pair {L1=100 nm,c=200 nm}\{L_1=100\ \mathrm{nm},c=200\ \mathrm{nm}\}.

We performed the numerical integration to test this combination of antennas. The results are gathered in Figure 6. The time-domain voltages and their spectra indicate that this S + ⊔ design successfully implements frequency demultiplexing which a much improved conservation of the amplitudes of the wavepackets. Still, the voltage induced by the f2f_2 wavepacket is slightly higher than the two others. This arises because the S + ⊔ antenna design lead to a slightly too high ∣∣h~rf(k2)∣∣2||\tilde{h}_{\mathrm{rf}}(k_2)||^2. This could be solved by allowing additional degrees of freedom in the antenna design. This versatility allows to design amplitude-conserving frequency demultiplexing operations for arbitrary sets of frequencies.

Figure 6. Time-resolved voltage expected at a distance r=60r = 60 μ\mum for a single wire emitting antenna and a ⊔-shaped receiving antenna (sketch in bottom inset). The coloured backgrounds indicate the temporal gates used for time gating. Top inset: Normalized power spectral density of these time gated signals.

Conclusion

We have described the spatio-temporal propagation of spin-wave wavepackets evolving in magnetic stripes, as driven by pulses of microwave magnetic field. We have clarified the influences of the excitation duration and of the spin wave dispersion relation, as well as the influence of the spin-wave linewidth. This led us to propose a criterion for the spatio-temporal separation of initially overlapping wavepackets that we illustrate by demultiplexing a complex signal that comprises three distinct frequencies, while preserving their relative amplitudes.

As all other SW-based devices, our multiplexer has a limited operational bandwidth that is set by the spin-wave dispersion relation. Our proposed concept is therefore limited to a few tens of GHz, essentially determined by the FMR frequency, the antenna shape and width, and the bias field required to obtain the desired FMR frequency and magnetization direction.

For the proposed device to be all-electrical and therefore suitable for full integration, the difficulty will be the on-chip generation of the field needed to bias the magnetization in the direction transverse to the spin wave conduit. Replacing an external magnet by exchange biasing over- and under-layers may be a solution; this however calls for material research on the generation of strong exchange bias fields that would preserve the Gilbert damping of the ferromagnetic layer. Future work will leverage this principle to design devices capable of filtering and processing multiple spin-wave channels in parallel.

Acknowledgments

This work was supported by the French RENATECH network, by the French National Research Agency (ANR) as part of the “Investissements d’Avenir” and France 2030 programs. This includes the PEPR SPIN projects ANR 22 EXSP 0008 and ANR 22 EXSP 0004. We thank Claude Chappert and Loukas Kokkinos for helpful comments.

AUTHOR DECLARATIONS

Conflict of Interest

The authors have no conflicts to disclose.

Author Contributions

G. Y. Thiancourt: Data curation (lead); Formal analysis (lead); Writing– original draft (equal); Writing– review and editing (equal); Investigation (equal).

T. Devolder: Funding acquisition (lead); Investigation (equal); Writing– original draft (equal); Writing– review and editing (equal);

DATA AVAILABILITY

The data that support the findings of this article are openly available [25].

Supplemental Materials: Modelling of spin-wave wavepackets excited by an RF burst for signal demultiplexing

This is supplementary of the paper ”Modelling of spin-wave wavepackets excited by an RF burst for signal demultiplexing” by G. T. Thiancourt and T. Devolder.

Hysteresis

Figure S1 displays the hysteresis loop calculated using TetraX2 [S16]. For the applied magnetic field of 35 mT used throughout this work, the waveguide is close to saturation. One can thus expect that the analytical expression given in Eq. (1) can be employed. We have validated this assumption by eigenmode simulations in Figure 1.c.

Figure S1. Hysteresis loop of a CoFeB waveguide with a thickness of 60 nm and a width of 5 μm\mu\mathrm{m} for a transverse applied field obtained from micromagnetic simulations using TetraX2 with a spatial discretization of 4×44 \times4 nm2^2.

Linearized susceptibility

Implementing Eq. (6) requires the evaluation of the susceptibility. For this purpose we still consider a thin ferromagnetic stripe of thickness tmagt_{\mathrm{mag}}, width wstripew_{\mathrm{stripe}}, and translational invariance along xx. To get an analytical expression of the susceptibility we disregard the edge domains and assume a uniform internal static field H0=H0y^\mathbf{H}_0 = H_0\hat{\mathbf{y}} that leads to a uniform equilibrium magnetization M0=Msy^\mathbf{M}_0 = M_s\hat{\mathbf{y}}.

Small-amplitude spin wave (SW) are excited by a transverse rf magnetic field h=(hx,0,hz)ei(k⋅r−ωt)\mathbf{h} = (h_x,0,h_z)e^{i(\mathbf{k}\cdot\mathbf{r}-\omega t)}, inducing magnetization fluctuations m=(mx,0,mz)ei(k⋅r−ωt)\mathbf{m} = (m_x,0,m_z)e^{i(\mathbf{k}\cdot\mathbf{r}-\omega t)}, with k=(kx,ky,0)\mathbf{k} = (k_x,k_y,0) and k2=kx2+n2π2/wstripe2k^2 = k_x^2 + n^2\pi^2/w_{\mathrm{stripe}}^2.

Linearizing the Landau–Lifshitz–Gilbert equation in the weak-damping limit (α≪1\alpha\ll1) yields the coupled equations for the transverse components (mx,mz)(m_x,m_z),

(Ωx(k)−iαω−iω+iωΩz(k)−iαω)(mxmz)=ωM(hxhz)(24)\begin{pmatrix} \Omega_x(k)-i\alpha\omega& -i\omega\\ +i\omega& \Omega_z(k)-i\alpha\omega \end{pmatrix} \begin{pmatrix} m_x\\ m_z \end{pmatrix} = \omega_M \begin{pmatrix} h_x\\ h_z \tag*{(24)} \end{pmatrix}

where ωM=γμ0Ms\omega_M = \gamma\mu_0M_s and the effective stiffness terms read

Ωz(k)=ωH+ωM(1−P),(25)\Omega_z(k) = \omega_H + \omega_M(1-P), \tag*{(25)}
Ωx(k)=ωH+ωMPkx2k2,(26)\Omega_x(k) = \omega_H + \omega_M P\frac{k_x^2}{k^2}, \tag*{(26)}

with ωH=γμ0H0\omega_H = \gamma\mu_0H_0 and PP the classical [S27] demagnetizing factor expressed in reciprocal space as

P(ktmag)=1+e−ktmag−1ktmag.(27)P(kt_{\mathrm{mag}}) = 1 + \frac{e^{-kt_{\mathrm{mag}}}-1}{kt_{\mathrm{mag}}}. \tag*{(27)}

The magnetic susceptibility tensor χ(k,ω)\chi(\mathbf{k},\omega) is obtained by inverting the above matrix. In the transverse (x,z)(x,z) basis, its non-zero components read

χxx(k,ω)=ωMΩz(k)Δα(k,ω),(28)\chi_{xx}(k,\omega) = \frac{\omega_M\Omega_z(k)}{\Delta_\alpha(k,\omega)}, \tag*{(28)}
χzz(k,ω)=ωMΩx(k)Δα(k,ω),(29)\chi_{zz}(k,\omega) = \frac{\omega_M\Omega_x(k)}{\Delta_\alpha(k,\omega)}, \tag*{(29)}

where all components share the common denominator

Δα(k,ω)=Ωx(k)Ωz(k)−ω2−iαω[Ωx(k)+Ωz(k)].(30)\Delta_\alpha(k,\omega) = \Omega_x(k)\Omega_z(k)-\omega^2-i\alpha\omega[\Omega_x(k)+\Omega_z(k)]. \tag*{(30)}

Since we have assumed a uniform equilibrium magnetization M0∥y^\mathbf{M}_0 \parallel\hat{\mathbf{y}}, the longitudinal susceptibility χyy\chi_{yy} vanishes.

Derivation of the phase shift to second order in kk

We make a series of approximations in the algebra leading to Eq. (14). First, we treat the antenna as infinitely narrow, following Eq. (13). Second, we expand the magnetic susceptibility to second order in wavevector to capture the curvature of the dispersion relation; the validity of this approximation is assessed in Section VIA. We rewrite the frequency near ω0\omega_0 by setting ω=ω0+δω\omega= \omega_0 + \delta\omega. Expanding the dispersion relation to second order around k0k_0, with δk=k−k0\delta k = k-k_0, and assuming ω0≫vgδk+(τD2vg3δk2)/r+δω\omega_0 \gg v_g\delta k + (\tau_D^2v_g^3\delta k^2)/r + \delta\omega, the magnetic susceptibility becomes

χxx(kx,ω)=ωmax(k0)22ω0(vgδk+(τD2vg3δk2)/r+δω)−iω0Δω(k0)(31)\chi^{xx}(k_x,\omega) = \frac{\omega_{\mathrm{max}}(k_0)^2}{2\omega_0\left(v_g\delta k+(\tau_D^2v_g^3\delta k^2)/r+\delta\omega\right)-i\omega_0\Delta\omega(k_0)} \tag*{(31)}

where ωmax⁡2(k0)=γ02Ms(H0+Ms(1−P(k0)))\omega_{\max}^{2}(k_0)=\gamma_0^{2}M_s\left(H_0+M_s\left(1-P(k_0)\right)\right) and P(k0)P(k_0) is the simplified dipolar factor. Integrating S~21(ω,r)\widetilde{S}_{21}(\omega,r) around k0k_0 yields

S~21(ω,r)∝iωmax⁡2(k0)vgω0hrf(k0)2e−Δω0r2vge−ik(ω)r.(32)\widetilde{S}_{21}(\omega,r)\propto\frac{i\omega_{\max}^{2}(k_0)}{v_g\omega_0}h_{\mathrm{rf}}(k_0)^2e^{-\frac{\Delta\omega_0 r}{2v_g}}e^{-ik(\omega)r}. \tag*{(32)}

Neglecting slow terms (i.e. rΔω0τDδωr\Delta\omega_0\tau_D\delta\omega), the phasor can be rewritten as

ik(ω)r=i(k0r+τgδω+12τD2δω2+O(δω3)).(33)ik(\omega)r=i\left(k_0r+\tau_g\delta\omega+\frac{1}{2}\tau_D^2\delta\omega^2+O(\delta\omega^3)\right). \tag*{(33)}

We thus recover the second-order expansion of the phase shift in δω\delta\omega (Eq. (5)).

Phase oscillation within the pulse envelope

The phasor term cos⁡[φ(r,t)]\cos[\varphi(r,t)] in eq. 19 captures both the wave character of the carrier and the dispersion-induced quadratic phase (chirp). Its full expression is:

φ(r,t)=−τD2(t−τvg)22τout4−12tan⁡−1(τD2τ02)⏟chirp-induced phase+(k0r−ω0t)⏟carrier wave(34)\varphi(r,t)=-\underbrace{\frac{\tau_D^2(t-\tau_{v_g})^2}{2\tau_{\mathrm{out}}^4}-\frac{1}{2}\tan^{-1}\left(\frac{\tau_D^2}{\tau_0^2}\right)}_{\text{chirp-induced phase}}+\underbrace{(k_0r-\omega_0t)}_{\text{carrier wave}} \tag*{(34)}

The carrier term describes the underlying harmonic oscillation with a phase front advancing at r=ω0t/k0r=\omega_0t/k_0. The quadratic contribution in eq. 19 represents a time-dependent chirp centred around r=vgtr=v_gt. It reflects a continuous redistribution of instantaneous frequencies across the pulse, with different temporal components acquiring distinct phase shifts during propagation. The strength of this chirp is governed by the competition between the dispersion timescale τD4\tau_D^4 and the effective temporal width τout\tau_{\mathrm{out}}, leading to a progressive deformation of the phase profile as the wavepacket broadens. The Arctan term corresponds to a global phase offset that depends solely on the ratio τD/τ0\tau_D/\tau_0. This contribution is analogous to a Gouy-like phase shift [S28–S30]: it does not modify the local frequency content of the wavepacket — around t=r/vgt=r/v_g — but represents a cumulative phase lag acquired during propagation. Physically, it originates from the same dispersive mechanism responsible for temporal broadening and can be interpreted as the phase counter-part of the energy spreading in time. It is worth noting that the instantaneous angular frequency, obtained by differentiating Eq. 19, grows without bound as t→∞t\to\infty, which could seem unphysical at first sight. However, this divergence is not happening since the phasor factor is weighted by a Gaussian envelope that suppresses all contributions at ∣t−τvg∣≳τout\lvert t-\tau_{v_g}\rvert\gtrsim\tau_{\mathrm{out}}. The phase expression is therefore only meaningful within the temporal support of the pulse, where the chirp remains a small correction to the carrier frequency ω0\omega_0.

Case of the vanishing group velocity

Let us examine the flat-band limit when vg→0v_g\to0. This pathological situation lies outside the validity range of the (14) since the expansion in (31) required a well-defined group velocity.

For vg→0v_g\to0 we need to restart from eq. 6. The dispersion reduces to ω(kx)=ωFMR\omega(k_x)=\omega_{\mathrm{FMR}} with a constant linewidth such that the susceptibility is independent from the wavevector. It was χxx(kx,ω)=χ~xx(k=0,ω)≡χ~xx(ω)\chi^{xx}(k_x,\omega)=\tilde{\chi}^{xx}(k=0,\omega)\equiv\tilde{\chi}^{xx}(\omega), as if there was a unique SW and if it was confined in all directions. Using eq. 6 the transmission parameter is then simply:

S~21(ω,r)=χ~xx(ω)δr=0,(35)\widetilde{S}_{21}(\omega,r)=\tilde{\chi}^{xx}(\omega)\delta_{r=0}, \tag*{(35)}

For r>0r>0 the transit time r/vgr/v_g diverges; the wavepacket spends an infinite time in the absorbing medium and is completely attenuated when arriving at the position rr. There is simply no signal at the receiving antenna, as expressed from the Dirac function in eq. S36. For r=0r=0 we recover the classical VNA-FMR configuration [S31] when a single antenna at r=0r=0 is used for both emitting and receiving the SWs, and the S~21(ω,r)\widetilde{S}_{21}(\omega,r) signal is directly linked with the susceptibility and only present below the emitting antenna.

The corresponding impulse response s21(t,r)s_{21}(t,r) is then simply:

s21(t,r)∝(sin⁡(ωFMRt)exp⁡(−∣t∣ΔωFMR2))δr=0.(36)s_{21}(t,r)\propto\left(\sin(\omega_{\mathrm{FMR}}t)\exp\left(-\frac{\lvert t\rvert\Delta\omega_{\mathrm{FMR}}}{2}\right)\right)\delta_{r=0}. \tag*{(36)}

The transmission response to a Gaussian stimuli {g(t),G~(ω)}\{g(t),\widetilde{G}(\omega)\} is, therefore, defined as a multiplication in frequency domain,

S~out(ω,r)=(G~(ω)χ~xx(ω))δr=0,(37)\widetilde{S}_{\mathrm{out}}(\omega,r)=\left(\widetilde{G}(\omega)\tilde{\chi}^{xx}(\omega)\right)\delta_{r=0}, \tag*{(37)}

or equivalently the time-domain convolution:

soutvg=0(t,r)=(s21(t,r)∗g(t))δr=0.(38)s_{\mathrm{out}}^{v_g=0}(t,r)=\left(s_{21}(t,r)*g(t)\right)\delta_{r=0}. \tag*{(38)}

Other criteria for the separability

In general, the criterion for the separability of two wavepackets can be parametrized by a positive number ϵ\epsilon. This reads:

∣Δτg(ω1,ω2)∣≥ϵτ0[∥τout2(ω1)∥+∥τout2(ω2)∥].(39)\left\lvert\Delta\tau_g(\omega_1,\omega_2) \right\rvert\ge\frac{\epsilon}{\tau_0} \left[ \left\lVert\tau_{\mathrm{out}}^2(\omega_1) \right\rVert+ \left\lVert\tau_{\mathrm{out}}^2(\omega_2) \right\rVert\right]. \tag*{(39)}

In the main document, we have chosen ϵ=1.18\epsilon= 1.18 to have wavepackets separated by the quadratic sum of their half width at half maximum (HWHM). ϵ=2.35\epsilon= 2.35 would account for a separation set by the full widths at half maximum (FWHM) of the two wavepackets.

An alternative separability ansatz is the use of a Rayleigh-like criterion, where the spacing between the two wavepackets must exceed the temporal width of each of them; this reads:

∣Δτg(ω1,ω2)∣≥2ϵτ0max⁡[∥τout2(ω1)∥,∥τout2(ω2)∥].(40)\left\lvert\Delta\tau_g(\omega_1,\omega_2) \right\rvert\ge\frac{2\epsilon}{\tau_0} \max\left[ \left\lVert\tau_{\mathrm{out}}^2(\omega_1) \right\rVert, \left\lVert\tau_{\mathrm{out}}^2(\omega_2) \right\rVert\right]. \tag*{(40)}

Figure S2 compares the two criteria for ϵ=1.18\epsilon= 1.18 and ϵ=2.35\epsilon= 2.35. As expected, tightening the separability criteria by increasing ϵ\epsilon raises the required spacing of the two carriers ω1\omega_1 and ω1\omega_1. At low frequencies, the two criteria (eqs. (39) and S40) yield similar constraints. In contrast, when aiming at higher carrier frequency ω1\omega_1, the Rayleigh-like criterion yields a more demanding (larger) Δfmin⁡\Delta f_{\min} than Eq. (39). This is due to the difference of the width of the two wavepackets, which tightens the Rayleigh-type criterion.

Figure S2. Antenna efficiency function for a 100 nm wide stripline antenna directly deposited on the magnetic surface.

References

  1. [2]C. Bayer, J. P. Park, H. Wang, M. Yan, C. E. Campbell, and P. A. Crowell, Spin waves in an inhomogeneously magnetized stripe, Phys. Rev. B 69, 134401 (2004).DOI
  2. [3]V. E. Demidov and S. O. Demokritov, Magnonic waveguides studied by microfocus brillouin light scattering, IEEE Trans. Magn. 51, 1 (2015).DOI
  3. [4]K. Perzlmaier, G. Woltersdorf, and C. H. Back, Observation of the propagation and interference of spin waves in ferromagnetic thin films, Physical Review B—Condensed Matter and Materials Physics 77, 054425 (2008).DOI
  4. [5]M. Covington, T. Crawford, and G. Parker, Time-resolved measurement of propagating spin waves in ferromagnetic thin films, Physical Review Letters 89, 237202 (2002).pubmed.ncbi.nlm.nih.gov/12485035
  5. [6]T. Devolder, G. Talmelli, S. M. Ngom, F. Ciubotaru, C. Adelmann, and C. Chappert, Measuring the dispersion relations of spin wave bands using time-of-flight spectroscopy, Phys. Rev. B 103, 214431 (2021).DOI
  6. [7]K. Dávidková, K. O. Levchenko, R. O. Serha, F. Bruckner, M. Lindner, C. Dubs, M. Urbánek, D. Suess, Q. Wang, and R. V. Verba, Spin-wave microscale RF delay lines for mid- and high-frequency 5G band, Journal of Applied Physics 138, (2025).DOI
  7. [8]B. Divinskiy, H. Merbouche, K. Nikolaev, S. Michaelis de Vasconcellos, R. Bratschitsch, D. Gouéré, R. Lebrun, V. Cros, J. Ben Youssef, P. Bortolotti, et al., Dispersionless propagation of ultrashort spin-wave pulses in ultrathin yttrium iron garnet waveguides, Phys. Rev. Appl. 16, 024028 (2021).DOI
  8. [9]G. Thiancourt, S. Ngom, N. Bardou, and T. Devolder, Unidirectional spin waves measured using propagating-spin-wave spectroscopy, Phys. Rev. Appl. 22, 034040 (2024).DOI
  9. [10]A. Martyshkin and A. Sadovnikov, Magnonic demultiplexer-switch based on the cluster of coupled ferrimagnetic mach-zehnder interferometers, Journal of Magnetism and Magnetic Materials 595, 171644 (2024).DOI
  10. [11]F. Heussner, G. Talmelli, M. Geilen, B. Heinz, T. Brächer, T. Meyer, F. Ciubotaru, C. Adelmann, K. Yamamoto, A. A. Serga, et al., Experimental realization of a passive gigahertz frequency-division demultiplexer for magnonic logic networks, physica status solidi (RRL)—Rapid Research Letters 14, 1900695 (2020).DOI
  11. [12]N. Zenbaa, C. Abert, F. Majcen, M. Kerber, R. O. Serha, S. Knauer, Q. Wang, T. Schrefl, D. Suess, and A. V. Chumak, A universal inverse-design magnonic device, Nature Electronics 8, 106 (2025).DOI
  12. [13]M. Bailleul, D. Olligs, and C. Fermon, Propagating spin wave spectroscopy in a permalloy film: A quantitative analysis, Appl. Phys. Lett. 83, 972 (2003).DOI
  13. [14]For implementation in an integrated device, this unpractical applied field of 35 mT could be replaced by two exchange-biasing layers sandwiching the magnetic layer, with the exchange bias set by field annealing in the direction transverse to the magnetic stripe. A structure of the form IrMn (20 nm)/CoFe (2 nm)/CoFeB (56 nm) /CoFe (2 nm) /IrMn (20 nm), with exchange coupling energy of J = 1.3 mJ/m² per interface [26] would indeed provide an exchange bias whose thickness-averaged effective field amounts to 2 × J/(Mₛtₘₐg) = 32 mT.
  14. [15]R. Damon and J. Eschbach, Magnetostatic modes of a ferromagnet slab, J. Phys. Chem. Solids 19, 308 (1961).DOI
  15. [16]L. Körber, G. Quasebarth, A. Otto, and A. Kákay, Finite-element dynamic-matrix approach for spin-wave dispersions in magnonic waveguides with arbitrary cross section, AIP Adv. 11, 095006 (2021).
  16. [17]B. A. Kalinikos and A. N. Slavin, Theory of dipole-exchange spin wave spectrum for ferromagnetic films with mixed exchange boundary conditions, J. Phys. C: Solid State Phys. 19, 7013 (1986).DOI
  17. [18]O. Gladii, M. Collet, K. Garcia-Hernandez, C. Cheng, S. Xavier, P. Bortolotti, V. Cros, Y. Henry, J.-V. Kim, A. Anane, et al., Spin wave amplification using the spin hall effect in permalloy/platinum bilayers, Applied Physics Letters 108 (2016).DOI
  18. [19]T. Devolder, Propagating-spin-wave spectroscopy using inductive antennas: Conditions for unidirectional energy flow, Phys. Rev. Appl. 20, 054057 (2023).DOI
  19. [20]To save time the transmission coefficient for negative frequencies can be constructed from the Hermitian symmetry condition S̃₂₁(−ω,r) = S̃*₂₁(ω,r), which reflects the real-valued nature of the voltage when in the time domain. The integration is performed over k ∈ [−20, 20] rad μm⁻¹ with a step size of 0.01 rad μm⁻¹, and over a frequency range from 4 to 20 GHz with a resolution of 2 MHz (The response is assumed null below 4 GHz). Caution must be taken not to alias the frequency spectrum by using an insufficiently large frequency step.
  20. [21]This assumption restricts the applicability of the model to situations where the pulse duration follows τ₀ ≫ τ_D so that the frequency content of the input pulse is well within the parabolic part of the dispersion relation.
  21. [22]A complete description of the transmission signal S̃₂₁(ω,r) requires accounting for all components of the rf magnetic field generated by the antenna. This can be achieved by summing the contributions arising from the in-plane and out-of-plane rf-field components (hᶦʳᶠ, hᵒʳᶠ), each weighted by the corresponding dynamic susceptibilities.
  22. [23]G. P. Agrawal, Fiber-optic communication systems (John Wiley & Sons, 2012).
  23. [24]The curves are evaluated using the values of τ_D and τ_g extracted from a parabolic Taylor expansion of the dispersion relation about 10 GHz.In both models the wave packets are normalized to the peak amplitude at the shortest propagation distance (20 μm).
  24. [25]G. Y. Thiancourt and T. Devolder, Dataset for the article: Amplitude-conserving frequency demultiplexer based on a spin wave delay line, Zenodo https://doi.org/10.5281/zenodo.13769398 (2026).

Paper details

vlnc:W_6h38x57z
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 2

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents