betaFeedback

WorksPhysics and Astronomy

FA2PbBr4: synthesis, structure and unusual optical properties of two polymorphs of formamidinium-based layered (110) hybrid perovskite

Abstract

Small cations such as guanidinium and cesium can act as templating cations to form low dimensional phases (2D, 1D, 0D) in the case of excess of organic halides. However, such phases with the widely used formamidinium (FA+) cation have not been reported so far. In this study, we discovered two novel low dimensional phases with a composition of FA2PbBr4 and investigated the prerequisites of their formation upon crystallization of FABr-excessive solutions of FAPbBr3. We found that both phases have the structure of (110) layered perovskite but are represented by two different polymorphs with eclipsed and staggered arrangement of adjacent layers. It was shown that FA2PbBr4 phases usually exist in a labile equilibrium with FAPbBr3 3D perovskite and can form composites with it. The optical properties of both polymorphs were comprehensively studied by means of absorption spectroscopy, diffuse reflection spectroscopy and photoluminescence spectroscopy. DFT calculations were applied to investigate the band structure of the FA2PbBr4 and to corroborate the conclusions on their optoelectronic properties. As a result, we found that FA2PbBr4 phases irradiated by UV can exhibit effective green photoluminescence due to a transfer of excitation energy to defective states or 3D perovskite inclusions.

Introduction

The outstanding optical and electronic properties of organo-inorganic haloplum­bates with a perovskite structure provided an unprecedented surge of interest as a new generation of semiconductor materials for efficient photovoltaic and optoelectronic devices. One of the most important features of this innovative class of semiconductors is the extraordinary tunability of their optoelectronic parameters through adjusting the connectivity of the inorganic anionic framework ¹.

The majority of structural design strategies are based on the concept of achieving the desired electronic dimensionality of a material by controlling the dimensionality of its inorganic framework², which is commonly reduced to layered (2D) or lower dimensional (1D, 0D) structures by introducing bulk organic cations acting as a template for the structure. A selection of a templating cation to form a framework of the desired topology is therefore a key issue for rational structural design of such materials.

Depending on the size and shape, an organic cation can either predetermine the only possible topology of the inorganic framework or provide several variants of co-packing with polyiodoplumbate anions. The first case is observed mainly for large cations with a long carbon chain, resulting in a set of structures practically limited by the class of (100) perovskites³. The second case is realized for relatively small cations with a size comparable to the Pb–X bond length (∼3\sim3 Å).

These small cations (A⁺) can form series of compounds with different ratio R = [A⁺]/[PbXₓⁿ⁻] and different packaging. An increase of R should imply a decrease in the number of halogen atoms in the first coordination sphere of the A⁺ and a simultaneous increase in the number of contacts between A⁺ cations. This can be well illustrated by a series of compounds with guanidinium (Gu⁺) cations GuPbI₃ (1D)⁴, Gu₂PbI₄ (2D)⁵, Gu₃PbI₅ (1D)⁶, Gu₄PbI₆ (0D)⁶ and with cesium cations CsPb₂Br₅ (2D)⁷, CsPbBr₃ (3D)⁸, Cs₄PbBr₆ (0D)⁸. For such systems (CsBr-PbBr₂ and GuBr-PbBr₂), stoichiometry of the precursors strongly affects the structural dimensionality of the forming phase. Surprisingly, so far there have been no attempts to isolate any low-dimensional phases with R > 1 (“Pb-deficient”) with the most frequently used formamidinium (FA⁺) and methylammonium (MA⁺) cations, while the size of these cations lies exactly between Gu⁺ and Cs⁺. This fact motivated us for the current research that yielded unexpected results presented in this article.

In this study, we investigated the possibility of low dimensional phases formation from the solutions of FABr-PbBr₂ and MABr-PbBr₂. We showed that, in the case of an excess of organic halides (FABr, MABr), two novel phases of (110) perovskite with composition FA₂PbBr₄ can be obtained in pure form whereas MA₂PbBr₄ does not exist. We determined the crystal structure of the two observed polymorphs of FA₂PbBr₄ and characterized their optoelectronic properties using absorption spectroscopy, diffuse reflection spectroscopy (DRS), photoluminescence excitation (PLE) and steady-state photoluminescence (PL) spectroscopy. Surprisingly, these two layered phases exhibit drastically different optical properties: while the trigonal modification has a noticeable photoluminescence, the monoclinic phase is only capable of transmitting excitation to adjacent 3D perovskite. DFT calculations were performed to investigate the band structure of the FA₂PbBr₄ and to analyze the origins of its peculiar photoluminescent properties.

Experimental section

Materials and methods. Formamidinium bromide (CH(NH₂)₂Br = FABr, Dyesol), methylammonium bromide (CH₃NH₃Br = MABr, Dyesol), lead bromide (PbBr₂, 99.99%, TCI), dimethylsulfoxide (DMSO, anhydrous, > 99.9%, Sigma-Aldrich), dimethylformamide (DMF, anhydrous, > 99.8%, Sigma-Aldrich), chlorobenzene (>99,8%, Sigma-Aldrich) and other antisolvents were commercially purchased.

All solutions were prepared at room temperature under stirring during 2 h in argon filled glove box, unless otherwise indicated.

Single crystal growth. Experiments to isolate low dimensional FA+^{+} and MA+^{+} containing phases were made using several solutions in DMF with FABr/PbBr2_2 ratio from 2 to 3 and the same solutions for the case of MABr excess.

Then we placed drops of all solutions on quartz glass and observed the process of crystal growth. Typical crystals from each droplet were isolated from the solution using a nylon loop, blotted and immediately transferred for X-ray measurements and solved as described below.

Single Crystal X-ray Diffraction. The single-crystal X-ray diffraction data set were collected on the ‘Belok’ beamline of the National Research Center ‘Kurchatov Institute’ (Moscow, Russian Federation) using a Rayonix SX165 CCD detector. In total, 720 frames were collected with an oscillation range of 1.0° in the ϕ\phi scanning mode using two different orientations for the crystal. The semi-empirical correction for absorption was applied using the Scala program9. The data were indexed and integrated using the utility iMOSFLM from the CCP4 software suite10. For details, see Table S1. The structure was solved by intrinsic phasing modification of direct methods and refined by a full-matrix least-squares technique on F2 with anisotropic displacement parameters for all non-hydrogen atoms. The hydrogen atoms were objectively localized from the different Fourier-maps and refined within the riding model with fixed isotropic displacement parameters [Uiso_{\mathrm{iso}}(H) = 1.2Ueq_{\mathrm{eq}}(N,C)]. All calculations were carried out using the SHELXTL program suite11.

Compoundm-FA2_2PbBr4_4t-FA2_2PbBr4_4t-FA2_2PbBr4_4*
Empirical formulaC4_4H20_{20}Br8_8N8_8Pb2_2C4_4H20_{20}Br8_8N8_8Pb2_2C4_4H20_{20}Br8_8N8_8Pb2_2
fwfw616.941213.711233.88
TT, K100100100
Crystal size, mm0.17×0.16×0.040.20×0.04×0.040.20×0.04×0.04
Crystal systemMonoclinicTriclinicTriclinic
Space groupP21/cP 2_1/cPP-1PP-1
aa, Å13.1313(9)8.5642(17)8.5642(17)
bb, Å7.9763(6)11.884(2)11.884(2)
cc, Å11.7972(8)14.312(3)14.312(3)
α\alpha, °9065.92(3)65.92(3)
β\beta, °91.4752(15)73.01(3)73.01(3)
γ\gamma, °9083.76(3)83.76(3)
VV, Å3^31235.221271.7(6)1271.7(6)
ZZ422
dcd_c, g cm−3^{-3}3.3183.173.222
F(0 0 0)F(0\ 0\ 0)108810481088
μ\mu, mm−1^{-1}26.55632.51732.519
θmax⁡\theta_{\max}, °32.64430.87230.872
Index range (h, k, l max)19, 12, 1710, 15, 1810, 15, 18
No. of reflections collected451655645566
No. of unique reflections (RintR_{\mathrm{int}})4490 (0.033)5529 (0.163)5242 (0.118)
No. of reflections with (I>2σ(I)I > 2\sigma(I))347544464435
Data / restraints / parameters4490 / 0 / 975529 / 0 / 1405242 / 0 / 159
R1R_1; wR2wR_2 (I>2σ(I)I > 2\sigma(I))0.0330; 0.07680.1620; 0.34560.1115; 0.2395
R1R_1; wR2wR_2 (all data)0.0332; 0.07850.1630; 0.35450.1188; 0.2434
Goodness-of-fit (GOF) on F2F^21.0342.5001.065
Extinction coefficient0.00230.0022(2)0.0022(2)
Tmin⁡T_{\min}; Tmax⁡T_{\max}0.091; 0.8160.060; 0.0600.060; 0.060
Δρmax⁡\Delta\rho_{\max}; Δρmin⁡\Delta\rho_{\min}, eÅ−3^{-3}1.58; -2.0220.87; -8.376.464; -4.798
Data completeness99.4%99.4%94.2%

Table S1. Crystallographic and structural refinement data for two polytypes of FA2_2PbBr4_4. The asterisk denotes the variant of refinement for t-FA2_2PbBr4_4 with excluded reflections.

Thin films preparation. Glass substrates were cleaned with detergent, flushed with distilled water and then sequentially washed in ultrasonic baths in acetone, isopropyl alcohol and distilled water. Substrates were further cleaned with UV-ozone for 15 min prior to their use.

A homogeneous solution of FABr:PbBr2_2 = 2:1 in DMSO-CB (1:1) mixture was prepared by slow drop-wise adding of 0.5 ml of chlorobenzene to equal volume of a 2.2 M FA2_2PbBr4_4 solution in DMSO at 110°C under vigorous stirring (to reach the concentration of resulting solution of 1.1M). Then the solution was cooled down to 60 °C and used for spin-coating of phase-pure m-FA2_2PbBr4_4 films.

The optimal parameters for obtaining a thin film of t-FA2_2PbBr4_4 were determined as the following: 1.25M solution of FABr:PbBr2_2 = 2.15:1 in DMSO, rotation rate of 4000 rpm for 50 s with CB dropwise added after 25 s and annealing at 110 °C for 10 min followed by annealing at 90 °C for 10 min. It is important to note that one of the key conditions of single-phase film fabrication, as well as its further storage, is low humidity, therefore, all operations must be carried out in a glove box.

Optical measurements. The absorption spectra of the films were recorded both in transmission mode (on a Jasco V-550 UV/Vis spectrophotometer in the wavelength range of 300–700 nm at a scanning speed of 100 nm/min) and in the diffuse reflectance mode (on a Perkin Elmer Lambda 950 spectrophotometer in the wavelength range of 300–800 nm) with wavelength resolution 1.0 nm. Steady-state PL measurements were performed on a microscope assembled using Thorlabs optomechanical components. Samples were photoexcited using a 405 nm laser (InTop, Russia) delivering 30 ps (FWHM) pulses in the continuous wave mode. A Flame (Ocean Optics, UK) spectrometer was used to record PL spectra.

Powder X-ray diffraction analysis was provided using Rigaku D/MAX 2500 (Japan) with a rotating copper anode (CuKα\alpha irradiation, 0.15418 nm) in the Bragg–Brentano geometry. XRD patterns were sequentially measured at a scanning speed of 0.2 deg/s.

Crystal chemical analysis. The fragmentation of the unit cell volume into “partial” specific volumes of moieties of the interest (FA+^{+} cations, [PbBr4_4]) in the structure is performed using Voronoi-Dirichlet polyhedra (VDP). The main algorithms of constructing VDP are implemented in ToposPro program package.12 VDP can often characterize not only relative, but also absolute atomic size in the crystal structure.13

To determine the degree of distortion of PbX6_6 octahedra in the structure, we used the equation introduced in ref.14:

Δd=16∑[dn−dd]2,(1)\Delta d = \frac{1}{6}\sum\left[\frac{d_n-d}{d}\right]^2, \tag*{(1)}

where dn_n - individual B-X distances, d - arithmetic mean values of the individual B-X distances.

DFT calculations. For calculation of electronic structure of FA2_2PbBr4_4 we used the DMol3 module from Materials Studio software package.15,16 In this program, the DFT method is realized on the basis of atomic functions. We applied the DNP+ basis (Double Numerical plus polarization with addition of diffuse functions) and spin-orbital coupling.

Results and Discussion

The crystallization of colorless crystals of FA2_2PbBr4_4 was observed for DMF solutions with FABr/PbBr2_2 =2-3. Depending on the conditions, two crystallization paths can be observed: in the case slow evaporation of a large unperturbed drop, thin plate-like crystals grow on the surface of the solution (1), whereas in the case of relatively rapid evaporation (small droplets), faceted prism-shaped crystals grow in the volume of the solution (2) (Figure S2). We resolved the structure of both types of crystals and found that they are two different phases with the same composition – FA2_2PbBr4_4. (Table 1). From a crystallographic point of view, these two phases are polymorphs, one of which is triclinic and the other is monoclinic (for simplicity, we denote them further as t-FA2_2PbBr4_4 and m-FA2_2PbBr4_4 respectively).

Crystallization from DMF solutions

Figure S2. The crystallization from DMF solutions with a ratio FABr:PbBr2=2.5:1\mathrm{FABr}:\mathrm{PbBr}_2 = 2.5:1. Photo (a) shows the case of fast evaporation resulting in faceted elongated prismatic crystals of the monoclinic phase (m-FA2PbBr4\mathrm{m\text{-}FA}_2\mathrm{PbBr}_4). The nucleation of this phase can occur both at the interface and in the bulk of the solution. Photo (b) shows the typical picture of triclinic (t-FA2PbBr4\mathrm{t\text{-}FA}_2\mathrm{PbBr}_4) phase crystallization, which usually forms under slow evaporation conditions, starts from the edge of droplet as a heterogeneous nucleation and grows further as thin transparent platelets.

Surprisingly, these two polymorphs crystallize sometimes simultaneously from a single droplet of solution (Figure S3) This implies that crystallization is controlled more by kinetics of solvent evaporation than by thermodynamics and indicates that the lattice energies of two polymorphs are close. Under equilibrium conditions without evaporation of the solvent, the formed crystals of the t-FA2_2PbBr4_4 coexist with a saturated solution for an unlimited time, but stirring triggers its slow recrystallization into m-FA2_2PbBr4_4. Also, phase-pure m-FA2_2PbBr4_4 can be obtained via CB vapour diffusion.

Examples of simultaneous crystallization of two polymorphs from a single droplet of solution

Figure S3. The examples of simultaneous crystallization of two polymorphs from a single droplet of solution (FABr:PbBr2=2.5:1\mathrm{FABr}:\mathrm{PbBr}_{2}=2.5:1).

In the same manner, we attempted to obtain crystals of MABr-excessive phases from solutions of MABr:PbBr2_2 with different precursor ratios (up to 3:1). However, in all the cases, only bright orange MAPbBr3_3 perovskite crystals grew from DMF and DMSO solutions as well known for this system.17

Peculiarities of the FA2_2PbBr4_4 crystal structure

Both FA2_2PbBr4_4 polymorphs have crystal structure of (110)-oriented layered perovskite, which consists of corner-connected PbBr6_6 octahedra forming corrugated layers separated with formamidinium cations (Figure 1, Table 1).

Figure 1. Projection of t-FA2_2PbBr4_4 crystal structure on (a) 0kl and (b) h0k plane and m-FA2_2PbBr4_4 on (c) h0k and (d) hk0 planes.

Polytypet-FA2_2PbBr4_4m-FA2_2PbBr4_4
AppearanceLarge thin plate-like crystalsFaceted prism-shaped crystals

Table 1. Crystallographic Data for two polytypes of FA2_2PbBr4_4.

Crystal systemTriclinicMonoclinic
Space groupP‾1\overline{P}1P21/cP2_1/c
Unit cell parametersa=8.5642(17)a = 8.5642(17) Å; b=11.884(2)b = 11.884(2) Å; c=14.312(3)c = 14.312(3) Å<br>α=65.92∘\alpha= 65.92^\circ; β=73.01∘\beta= 73.01^\circ; γ=83.76∘\gamma= 83.76^\circa=13.1313(9)a = 13.1313(9) Å; b=7.9763(6)b = 7.9763(6) Å; c=11.7972(8)c = 11.7972(8) Å<br>α=90.0∘\alpha= 90.0^\circ; β=91.52∘\beta= 91.52^\circ; γ=90.0∘\gamma= 90.0^\circ
Volume1271.7(6)1271.7(6) Å3^31271.7(6)1271.7(6) Å3^3
Z24
Density (calculated)3.2223.222 g/cm3^33.3183.318 g/cm3^3

Table 1 (PDF p. 3).

The main distinction between the two polytypes is different stacking of adjacent inorganic layers which can be described in terms of the layer shift factor (LSF)18. The m-FA2_2PbBr4_4 (Figure 1, b) has a staggered3^3 stacking of layers (LSF = [0.5, 0.06]) typical for the majority of previously reported (110) layered bromide perovskites 5,18–26, while the t-FA2_2PbBr4_4 (Figure 1, a) represents the first known structure of a bromoplumbate with an eclipsed stacking of the perovskite layers (LSF = [0.06, 0.09]).

Both structures are stabilized by hydrogen bonds formed by FA+^+ cations, each connected with several neighboring bromide anions thus templating the corrugated inorganic framework of FA2_2PbBr4_4. In both polymorphs formamidinium cations simultaneously occupy two different types of positions – intralayer and interlayer (see detailed analysis of FA+^+ positions in Figure S4) In terms of size, the former virtually corresponds to the cuboctahedral void occupied by the FA+^+ cation in FAPbBr3_3 (3D) perovskite. The only difference is the absence of one Br−^- in the first coordination sphere. In contrast, FA+^+ cation in interlayer positions forms hydrogen bonds simultaneously with two adjacent layers, thereby binding them together. Interestingly, both for the cation in the interlayer positions and in the interlayer ones, the coordination number is equal to 12, but the anions in the nearest environment are partially replaced by cations (FA+^+). An average specific volume of FA+^+ cations in different positions remains the same and has a negligible difference compared to FAPbBr3_3 (Figure S13, Table S5).

Crystal structure of t-FA₂PbBr₄ viewed down the b axis and four projections on crystallographic planes

Figure S4. Crystal structure of \mathrm{t\mathchar`-FA}_{2}\mathrm{PbBr}_{4} viewed down the b axis (in the center) and 4 projections on the planes (110)(110), (111)(111), (0\mathchar`-11), (01\mathchar`-2) containing flat FA+\mathrm{FA}^{+} cations in 4 corresponding independent orientations.

Image not extracted

Figure S13. The inner volume of Voronoi-Dirichlet polyhedron of FA+^+ cation in FA2_2PbBr4_4 crystal structure.

№ of the FA+^{+} cationVV, Å3^{3}
199.78
298.28
395.02
494.07
595.02
694.07
798.28
899.78

Table S5. The volumes of Voronoi-Dirichlet polyhedra for FA+^{+} cation containing in FA2_2PbBr4_4 unit cell.

The second important structural feature of two FA2_2PbBr4_4 polymorphs is a very short interlayer distance. Due to a small size of the FA+^+, the closest Br···Br distances between the layers in the t-FA2_2PbBr4_4 and m-FA2_2PbBr4_4 are 4.12 Å and 4.04 Å, respectively. It is even smaller than the edge length of the PbBr6_6 octahedron. To the best of our knowledge, this is one of the smallest interlayer distance reported for bromide perovskites so far (Table S7).

CompositionID*Min. interlayer distance, Åσ2\sigma^2Δd\Delta dFWHM of PL, meVRef
FA2_2PbBr4_4-t5164.1522.53.9220This work
FA2_2PbBr4_4-m6324.0426.55.0-This work
(N-MEDA)PbBr4_4584.3924.58.2880[2]
(Im,Gua)PbBr4_42034.4922.17.690[3]
(Gua, Tz)PbBr4_42025.1628.211.0350[3]
(EDBE)PbBr4_4675.7923.924.0800[4]
(3-APy-dp)PbBr4_43734.3221.19.8743[5]
(3APIm-dp)PbBr4_41634.4820.826.0>750[6]
(EPZ-dp)PbBr4_43753.903841370[7]

Table S7. Comparison of the main geometrical parameters (bond angle variance σ2\sigma^2 and bond length distortion Δd\Delta d) of the FA2_2PbBr4_4 and similar (110) layered bromoplumbate perovskites.

The unique feature of the t-FA2_2PbBr4_4 is the lowest degree of inorganic lattice distortion (Δd\Delta d) among all the (110) bromoplumbate perovskites known so far. This means that all the Pb–Br bonds have approximately same length. Indeed, in the most of hybrid halide perovskites the inorganic framework distortion occurs primarily because the organic cation (or its part bearing the positive charge and interacting with inorganic lattice) mismatches the size of the cuboctahedral void. On the contrary, the FA+^+ cation is only slightly larger than the cuboctahedral void (tolerance factor about 1.08)27 and, as a result, it keeps the structure slightly distorted only.

An important feature of the t-FA2_2PbBr4_4 polymorph is the presence of a significant number of defects and stacking faults in single crystals, which is reflected in the rather low quality of the collected XRD data and high R-factor.

Comparison of “templating ability” of FA+^+ and MA+^+ cations

In order to understand why the layered perovskite is formed in the case of formamidinium, but does not exist for methylammonium, we compared the structures of the known (110) lead halide perovskites with various organic cations (listed in Table S7) and revealed the common features of the organic cations. We propose three main requirements that an organic cation has to meet in order to template the (110) layered structure: it should be able to form multiple hydrogen bonds and at the same time be rigid and “linkering” (i. e. be connected with adjacent perovskite layers). Another common, but not necessary prerequisite is the planar geometry of the cations, which determines their effective packing. Simultaneous compliance with these requirements can be inherent in both singly and doubly charged cations making them effective templating agents. Generally speaking, this explains why only a few (110) perovskites are known so far (Table S7).

Obviously, the formamidinium satisfies all these three requirements, whereas methylammonium does not. As a result, a similar (110) layered perovskite structure does not form with MA+^+ cations.

FA2_2PbBr4_4 films deposition features: overcoming competing crystallization of phases

To investigate further the properties of FA2_2PbBr4_4 phases we obtained it in a form of thin films. However, the deposition of phase-pure films is hindered by competing crystallization of 3D perovskite phase due to a labile equilibrium (1) between these solid phases:

FA2PbBr4(s)↔FAPbBr3(s)+FABr(s)(2)\mathrm{FA_2PbBr_4}_{(s)} \leftrightarrow\mathrm{FAPbBr_3}_{(s)} + \mathrm{FABr}_{(s)} \tag*{(2)}

As a result, in the case of solutions with FABr:PbBr2_2 = 2:1 both in DMF and DMSO with or without of antisolvents an admixture of the 3D perovskite phase has always been observed in the films obtained by conventional spin-coating. To overcome this issue, we proposed two approaches.

The first is a simple addition of 15% FABr excess in solution to shift the equilibrium (1) to the right which results in single phase films of t-FA2_2PbBr4_4 (Figure 2). The second one is a new technique of film processing from a homogeneous solvent – antisolvent mixture (DMSO-CB), prepared at elevated temperature. The essence of latter approach is to reach slowly the supersaturated state of the solution before spin-coating, in which nuclei of the composition corresponding to the composition of the solution form predominantly. The films obtained in this way are characterized by high transparency and uniform pale fawn color. SEM images show that the films are uniform and have no pinholes (Figure S7). The thickness of the film is about 0.85 µm (Figure S7). The crystallites have elongated form with average length about 1.5 µm (up to 3 µm) and width about 0.5 µm (Figure S7).

XRD pattern of phase-pure t-FA2PbBr4 thin film and simulated powder diffraction patterns of t-FA2PbBr4 and FAPbBr3

Figure 2. XRD pattern of phase-pure t-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} thin film and simulated powder diffraction patterns of t-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} and FAPbBr3\mathrm{FAPbBr}_{3}.

SEM micrographs of top surface (a, c) and cross-section (b) of the m-FA₂PbBr₄ thin film

Figure S7. SEM micrographs of top surface (a, c) and cross-section (b) of the m-FA₂PbBr₄ thin film.

It should be noted that, being a layered perovskite, both polymorphs of the FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} are very sensitive to water vapors. Even at relative humidity of 30–40% they decompose forming FAPbBr3\mathrm{FAPbBr}_{3}. We associate this with the ability of water to solvate preferably and “to extract” FABr\mathrm{FABr} efficiently as a protic solvent28, shifting the equilibrium (1) towards the 3D perovskite (Figure S5).

XRD pattern of the t-FA2PbBr4 film

Figure S5. XRD pattern of the t-FA2PbBr4t\text{-}\mathrm{FA}_{2}\mathrm{PbBr}_{4} film annealed during 10 min at 120 °C in argon glove box or in air (humidity ~ 35%) at 80 °C; at the bottom – two simulated powder diffraction patterns of t-FA2PbBr4t\text{-}\mathrm{FA}_{2}\mathrm{PbBr}_{4} and FAPbBr3\mathrm{FAPbBr}_{3} respectively.

In addition, we studied the effect of the partial replacement of FA+\mathrm{FA}^{+} cations with MA+\mathrm{MA}^{+} in solutions on the phase composition of the films. In particular, it was found that at a [FA+]/[MA+][\mathrm{FA}^{+}]/[\mathrm{MA}^{+}] ratio R = 0.75 (the overall ratio of organic cations to PbBr2\mathrm{PbBr}_{2} was kept equal to 2), the FAPbBr3\mathrm{FAPbBr}_{3} phase is formed predominantly along with FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4}. With a decrease of R, the amount of 3D phase of perovskite increases even more and at R = 0.25 XRD does not show any traces of layered perovskite (Figure S6). Simultaneously, the 100 and 200 reflections of FAPbBr3\mathrm{FAPbBr}_{3} shift to larger angles, indicating the formation of (FAxMA1−x)PbBr3(\mathrm{FA}_{x}\mathrm{MA}_{1-x})\mathrm{PbBr}_{3} solid solutions.

XRD pattern of films of general composition A2PbBr4

Figure S6. XRD pattern of the films of general composition A2PbBr4\mathrm{A}_{2}\mathrm{PbBr}_{4} (2ABr+PbBr2) with different FABr/MABr ratio from 3:1 “(FA0.75MA0.25)2PbBr4(\mathrm{FA}_{0.75}\mathrm{MA}_{0.25})_{2}\mathrm{PbBr}_{4}” to 1:3 “(FA0.25MA0.75)2PbBr4(\mathrm{FA}_{0.25}\mathrm{MA}_{0.75})_{2}\mathrm{PbBr}_{4}” spin-coated with chlorobenzene dripping (unless otherwise indicated) at 25 s of rotation; at the bottom – two simulated powder diffraction patterns of t-FA2PbBr4t\text{-}\mathrm{FA}_{2}\mathrm{PbBr}_{4} and FAPbBr3\mathrm{FAPbBr}_{3} respectively.

Thus, it was shown that FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} does not form substitution solid solutions with methylammonium. On the contrary, introducing MA+\mathrm{MA}^{+} results in destabilization of the layered phase.

Optical properties and electronic structure

A diffuse reflectance spectra of the t-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} and m-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} thin film on quartz glass reveal an absorption edge at 455 and 420 nm respectively. According to the analysis of the spectra by the Tauc plot the optical band gaps of t-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} and m-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} are 2.82 eV and 3.00 eV, respectively (Figure 3). The former is the lowest value of optical EgE_{\mathrm{g}} known for (110) bromide perovskites (Table S8). As shown below, we associate such a small value of EgE_{\mathrm{g}} with weak orbital overlapping (Br…Br) due to very short interlayer distance compared to other (110) bromide perovskites (4.15 Å for t-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4}, see Table S7).

Figure 3. The diffuse reflectance spectra of the triclinic (t) and monoclinic (m) polytypes of FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} in Tauc coordinates and in Absorbance units (in the inset).

Compositionmin. inter-layer distance, ÅPLmax, eVFWHM of PL, meVOptical bandgap, eVRef
FA2_2PbBr4_4(m)4.04--3.00This work
FA2_2PbBr4_4(t)4.152.91** 2.45***105 2352.82This work
(N-MEDA)PbBr4_44.392.22(STE), 2.95(FE)8802.99[2]
(Im,Gua)PbBr4_44.492.20802.88[3]
(Gua,Tz)PbBr4_45.161.77(STE), 2.36(STE)3502.95[3]
(EDSTE)PbBr4_45.792.17(STE)8003.22[4]
(3-APy-dp)PbBr4_44.322.10(STE)7432.97[5]
(3APIm-dp)PbBr4_44.472.10(STE), 2.92(FE)>7502.92[6]
(EPZ-dp)PbBr4_43.902.08(ST)3703.12[7]

Table S8. Comparison of the main optoelectronic parameters of FA2_2PbBr4_4 and similar (110) layered bromoplumbate perovskites: PLmax stands for center of photoluminescence emission band; the optical bandgaps were determined in all cases as first absorption edge on UV-Vis spectrum; abbreviations FE and STE stands for free excitons and bounded excitons respectively.

An absorption spectrum of the m-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} recorded in transmission mode exhibits a clear excitonic band centered at 3.15 eV (Figure S8). The flat maximum of the exciton band most likely indicates the presence of several energy-related exciton transitions associated with anisotropic deformation of the octahedra29. Fitting of m-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} spectrum according to the Elliott model gives a bandgap (Eg) of continuum transitions at 3.3 eV and an exciton binding energy of 170 meV, which are very typical values for bromoplumbate perovskites.

Absorption spectrum of the m-FA₂PbBr₄ thin film

Figure S8. Absorption spectrum of the m-FA₂PbBr₄ thin film.

To reveal the origin of electronic transitions in t-FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4}, we performed DFT calculations using the refined crystallographic data (see details in SI). The calculations reveal a direct bandgap of 3.14 eV (Figure 5a, Table S2), which fairly agrees with the experimental value. The top of the valence band formed by p-orbitals of Br and bottom of the conduction band formed by p-orbitals of Pb (Figure 4b), which is typical for hybrid lead bromide perovskites.25 Therefore, near-bandgap electronic transitions are dominated by 6p Br−^{-} to 6p Pb2+^{2+} states. A relatively small dispersion of the bands along the layers directions (x,y) in FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} compared to (100) layered bromide perovskites is explained by a lower electronic dimensionality of the “corrugated” (110) layered structures25,26.

Band structure and electronic density of states of FA2PbBr4(t), and bandgap dependence on interlayer distance

Figure 4. Band structure (a) and electronic density of states (DOS) (b) of FA2_2PbBr4_4(t) obtained by DFT calculations. The dependences (c) of bandgap values (EgE_{\mathrm{g}}) from the distance between inorganic layers (dd) for two series of model structures.

Image not extracted

Figure 5. The appearance of FA2_2PbBr4_4(t) single crystal (a), from two areas (1 and 2) of which the PL spectra were recorded. The thin film of FA2_2PbBr4_4(t) on glass under visible (b) and UV (c) irradiation and corresponding PL (d, 3) and PLE spectra (e). All spectra on figure (d) were obtained under irradiation of diode laser emitting at 405 nm. Spectrum (4) from FAPbBr3_3 perovskite crystals was taken under similar conditions and presented for comparison.

FunctionalPBEPW91HCTH
EgE_{\mathrm{g}} (eV)2.882.863.14

Table S2. Bandgap values of t-FA2_2PbBr4_4 calculated using various functionals.

The bandgap of the t-FA2_2PbBr4_4 is noticeably smaller than that for the most of related (110) lead bromide perovskites, which can be associated with both an unusually small interlayer distance (dd) and a relatively small distortion of inorganic framework (Table S7). To distinguish these two effects, we performed calculations of the electronic structure for two series of model structures (Figure S9, Figure S10) derived from the experimentally solved structure of the FA2_2PbBr4_4 (see detailed description in SI). The structures of the first series preserve the geometry of inorganic framework of the real structure (the octahedra distortion and tilting) and have different dmeand_{\mathrm{mean}} from 3.16 to 9.65 Å (Table S3, Figure S9). Expectedly, the main change in the band structure is an increase of the bandgap with the increase of the interlayer distance (Figure 4c). Moreover, Eg(d)E_{\mathrm{g}}(d) rises mainly within the range of 3.5 - 4.5 Å and reaches further a plateau at d>4.6d > 4.6 Å (Fig. 6c).

Model undistorted eclipsed structures with different interlayer distances

Figure S9. Model undistorted eclipsed structures with different interlayer distances (d) from 3.5 Å to 10 Å.

Structuredmean(Br⋯Br)d_{\mathrm{mean}}(\mathrm{Br}\cdots\mathrm{Br}), ÅEgE_{\mathrm{g}}, eV
Structure 13.1602.940
Structure 23.4653.011
Structure 33.9853.080
Structure 44.3203.106
Structure 54.7603.127
Structure 65.1653.140
Structure 76.003.149
Structure 86.883.153
Structure 99.653.154

Table S3. The mean interlayer distances and calculated band gaps (EgE_{\mathrm{g}}) of corresponding distorted (with inorganic framework identical to real FA2_2PbBr4_4) eclipsed model structures.

Image not extracted

Figure S10. Model undistorted eclipsed structures with different interlayer distances (dd) from 3.5 Å to 10 Å.

Such a dependency of Eg(d)E_{\mathrm{g}}(d) originates obviously from the contribution of a relatively weak interlayer electronic coupling due to partial overlapping of the orbitals of terminal Br atoms. Interestingly, this Br···Br overlapping contributes in the band structure even at the distances significantly exceeding the doubled value of the van der Waals radius of Br (1.85 Å) and doubled ionic radius the bromide (1.96 Å), which are usually considered as the upper limits for weak orbital overlapping29. For another series of model structures with undistorted inorganic framework and a similar set of interlayer distances (Table S9, Figure S10), a Eg(d)E_{\mathrm{g}}(d) curve has a similar shape, although it is downshifted by a constant of -0.11 eV (Fig. 6c). Based on these two tendencies, we evaluated quantitatively the contribution of two main factors to the total bangap value: -0.045 eV for the weak interlayer orbital overlapping and +0.11 eV for the octahedra distortion.

The photoluminescent properties of the two polymorphs differ dramatically. Whereas phase-pure m-FA2_2PbBr4_4 exhibits no emission at room temperature, a thin film of t-FA2_2PbBr4_4 shows intense green photoluminescence (PL) with a maximum centered at 2.37 eV (523 nm), despite a negligible absorption in the visible range (Figure 5c). The observed emission band for the films is far from that for 3D perovskite (FAPbBr3_3), and, in addition, is noticeably wider. Therefore, it is hardly possible to attribute the observed emission directly to the perovskite phase.

To further reveal a nature of the radiative recombination in the t-FA2_2PbBr4_4 we collected the spectra from single crystals. An important feature of t-FA2_2PbBr4_4 crystals is the presence of colorless and pale-yellow areas (Figure 5a). We recorded the emission spectra from these two areas using a fluorescent microscope under the excitation by diode laser at 405 nm. The spots in transparent areas (“1” in the Figure 5) demonstrate a main narrow peak at 2.91 eV and a second broad peak of lower intensity centered approximately at 2.46 eV. The first peak can be clearly attributed to intrinsic exciton radiative recombination. For the spots in the pale yellow regions of the crystal, an inverse intensity ratio of two peaks is observed.

The origin of the broad band at 2.46 eV with a significant Stokes shift and FWHM of 0.2 eV is rather unclear. The most obvious explanation could be the presence of an impurity phase with a smaller band gap. However, this band is far from a position of PL maximum characteristic for FAPbBr3_3 thin films (2.23 eV)30 and also does not match to emission peak of FAPbBr3_3 seed crystals (2.16 eV) formed in FABr-excessive solution in DMF (Figure 5d, “4”). Moreover, partially colored and completely transparent crystals are indistinguishable using X-ray methods (neither powder-XRD nor single-crystal solution). Therefore, it can be concluded that the coloring is not associated with the presence of a new phase, but rather is a consequence of the appearance of some centers of radiative recombination inside the phase.

Such centers can correspond either to self-trapped excitons (STEs) or to a special type of bulk or surface static defects. The STEs are widely known for halide perovskites and especially for (110) lead bromide perovskites. In most cases recombination via STEs are associated with a large Stokes shift and broad FWHM. However, the width of t-FA2_2PbBr4_4 second emission band is significantly narrower in comparison with a typical values for related perovskites (Table S8).

In addition, as can be seen from Figure 5d, the spectrum taken from the colored area of the t-FA2_2PbBr4_4 crystal is very similar to the spectrum from a thin film of the same composition. The simultaneous increase of the intensity of the band at 2.46 eV and disappearance of an excitonic band for a thin film compared to single crystal implies the dependence of PL from the surface-bulk ratio. Accordingly, the observed emission band should rather be attributed to surface defects.

The latter assumption was further corroborated by means of photoluminescence excitation spectroscopy (PLE). The PLE spectrum was measured from the same thin film and showed an excitonic absorption edge near 3 eV and an additional band between 2.8 eV and 3.0 eV. This band matches well with the observed pale yellow color characteristic for thin films of t-FA2_2PbBr4_4. Taking into account the luminescence spectra, this band can be interpreted as below bandgap absorption caused by surface defects. Additionally, the shape of the PLE spectrum implies the effective energy transfer from the intrinsic excited states of t-FA2_2PbBr4_4 to the (defect) states related to the radiative recombination.

The origin of the assumed defect states may be related to multiple stacking faults in the structure of t-FA2_2PbBr4_4, as well as to similar intergrowth structures between the polymorphs. Another explanation relates to the nanoparticles of FAPbBr3_3 which may exist in the film in a small concentration remaining undetectable by the applied methods of composition characterization. According to the literature, FAPbBr3_3 nanoparticles with a size smaller than 10 nm demonstrate a blue shift of PL about 0.1 eV 31,32 compared to a thin film (2.2–2.3 eV). This implies that only very small nanoparticles will have enough blue shift to explain the observed emission peak for the films. Noteworthy, the narrow bright emission induced by lower-bandgap 3D perovskite nanoparticles “embedded” inside the matrix of larger-bandgap material is a known phenomenon for analogous cases of CsPbBr3_3 and Cs4_4PbBr6_6 respectively 33,34. Therefore, the presence of embedded FAPbBr3_3 nanoparticles in a small concentration may be plausible explanation of photoluminescence properties of t-FA2_2PbBr4_4 films.

The relatively “narrow” bandgap of t-FA2_2PbBr4_4 was explained via modelling of band structure for series of related structures. Based on model calculations, we evaluated quantitatively the contribution of the overall distortion of inorganic framework and the weak interlayer orbital overlapping to the total bandgap value of FA2_2PbBr4_4 as -0.045 eV and +0.11 eV respectively.

We found that single crystals of t-FA2_2PbBr4_4 demonstrate simultaneously two photoluminescence bands: free excitonic one at 2.91 eV and another band at 2.46 eV with a broad FWHM. The second band is associated with radiative recombination via defect states existing on the surface of the FA2_2PbBr4_4 single crystals. According to PLE these defects are responsible for intense green photoluminescence of phase-pure t-FA2_2PbBr4_4 thin films with a maximum at 2.37 eV.

Conclusions

To sum up, we investigated the formation of low dimensional phases from FABr-excessive FABr-PbBr2_2 solutions and discovered new layered (110) bromoplumbate perovskite FA2_2PbBr4_4 represented by two polymorphs – triclinic and monoclinic. The first polymorph demonstrates a unique eclipsed manner of the perovskite layers stacking whereas the monoclinic one has a staggered one typical for (110) perovskites. Both structures are characterized by unusually small interlayer distance of 4.15 Å for t-FA2_2PbBr4_4 and 4.04 Å for m-FA2_2PbBr4_4. In addition, t-FA2_2PbBr4_4 has the most undistorted inorganic framework among all (110) bromoplumbate perovskites known so far.

The optoelectronic properties of FA2_2PbBr4_4 polymorphs were comprehensively characterized from both experimental and theoretical points of view. It was found that t-FA2_2PbBr4_4 has an optical bandgap of 2.8 eV, which is the lowest value among (110) bromide perovskites, whereas a bandgap of m-FA2_2PbBr4_4 is 3.0 eV.

Associated Content

The Supporting Information is available free of charge via the Internet at http://pubs.acs.org.

Author Information

Corresponding Author

[email protected]

Author Contributions

#These authors contributed equally.

The manuscript was written through contributions of all authors. All authors have given approval to the final version of the manuscript.

Notes

The authors declare no competing financial interest.

Funding Sources

This research was financially supported by the Russian Science Foundation (Project No. 19-73-30022).

Acknowledgment

The authors are grateful to Aleksandra Shatilova for her help with experiments and to Artem Ordinartsev for introducing band structure analysis through python scripting.

DFT calculations were carried out using computational resources provided by Resource Center “Computer Center of SPbU”.

The X-ray powder diffraction analysis was provided using Rigaku D/MAX 2500 diffractomer (the Faculty of Materials Science, Lomonosov Moscow State University).

FA2PbBr4FA_{2}PbBr_{4}: synthesis, structure and unusual optical properties of two polymorphs of formamidinium-based layered (110) hybrid perovskite

Sergey A. Fateev; Andrey A. Petrov; Ekaterina I. Marchenko; Yan V. Zubavichus; Victor N. Khrustalev; Andrey V. Petrov; Sergey M. Aksenov; Eugene A. Goodilin; Alexey B. Tarasov

Supporting Information

{sup}#` – these authors contributed equally

*E-mail: [email protected]

Crystal structure of two polytypes of FA2_2PbBr4_4

Crystallographic data have been deposited with the Cambridge Crystallographic Data Center, CCDC 1967975. The supplementary crystallographic data can be obtained free of charge from the Cambridge Crystallographic Data Centre via www.ccdc.cam.ac.uk/data_request/cif.

The first FA2_2PbBr4_4 polytype of monoclinic crystal system was denoted as m-FA2_2PbBr4_4, and the second triclinic polytype as t-FA2_2PbBr4_4. The crystallographic and structural refinement parameters for two phases presented in Table S1.

As for the second polytype, we have made several attempts to refine its structure using different crystals. Despite the faceted shape and transparency of crystals (Figure S1), they all had a low internal quality, apparently due to the presence of large stacking disorder. This matches very well with so-called order/disorder phenomenon (related to polytypism and polymorphism) realized in a small tilting and rotating of adjacent octahedral layers around the axis which is perpendicular to the plane of the layer. In this case the diffraction patterns are characterized by a low quality with weak and diffuse peaks.

Appearance of t-FA₂PbBr₄ plate-like single crystals

Figure S1. The appearance of t-FA2PbBr4\mathrm{t\text{-}FA}_2\mathrm{PbBr}_4 plate-like single crystals selected for refinement and mounted on sample holder tip. Opaque spots on the crystal surface are clots of Apiezon grease (was used to fix the crystal) and possibly droplets of residual solution.

The “best” dataset for the t-FA2_2PbBr4_4 phase was independently processed twice with slightly different assumptions. The first refinement was performed using the whole set of diffraction peaks to reach a good completeness (0.994, Table S1). The hydrogens were removed from the refinement cycles. Accurate refinement of the model without fixing of any distances or angles gives us the final R∼16.20R \sim16.20 based on 5529 I>3σII > 3\sigma_I. This value of the final R1 is rather high, but the result is comparable with those for the double layered hydroxide (DLH)-structures or clays and mica structures with similar stacking disorder.

However, the resulting model shows crystal chemical reasonability and can be considered as an average structure. The searching of the symmetry relationship between the layers which describe the whole set of the polytypes will be the object of our further crystallographic investigations.

The explanations for all observed Alerts were added to the corresponding CIF. In particular, the twinning was checked using the proposed twin matrix. However, the refined twin domain volume is less than 3% and, therefore, it was ignored. The mistake with the crystal size was fixed. The standard multi-scan absorption correction was used.

For another refinement, we excluded the 287 low-angle reflections with inaccurately measured intensities from the final steps of the refinement due to some intensity overloads for this part of the detector. This minor fraction of intensity overloads was allowed in order to achieve better I/sigma statistics for high-angle reflections. However, this assumption resulted in rather low completeness (94.2%). In addition, internally low quality of crystal also led to some systematic intensity distortions which can be explained by the high level of stacking disorder.

Details of synthesis and phase equilibrium

Details of the bandgap calculations

Assaying 3 different functionals (Table S2), we found that the differences in the shape of the bands are negligible, whereas the most plausible EgE_{\mathrm{g}} value (2.89 eV) was obtained from the HTCH, so it was used for all further calculations. All calculations were performed with atomic wave functions determined as a double numerical basis set with polarization (DNP) which is similar to 6-31G**[1].

DFT calculations for model (FA2_2PbBr4_4-derived) structures

Firstly, we showed that despite the strong hydrogen bonding the formamidinium cations have a negligible influence on the bandgap value of FA2_2PbBr4_4. To confirm this, we calculated the electronic structure for FA2_2PbBr4_4 unit cell without FA+^{+} cations and obtained almost similar value of the bandgap (EgE_{\mathrm{g}} = 3.14 eV with FA+^{+} and 3.11 eV without FA+^{+}).

Then we performed calculations of the electronic structure for two series of model structures derived from real t-FA2_2PbBr4_4 which has 2 different interlayer Br···Br distance (dd) of 4.15 Å and 4.63 Å. Since the structure contains the same number of distances of type 1 (4.15 Å) and type 2 (4.63 Å), the mean distance (dmeand_{\mathrm{mean}}) is 4.39 Å. The structures of the first series preserve the geometry of inorganic framework of the real FA2_2PbBr4_4 structure but have different dmeand_{\mathrm{mean}} from 3.16 to 9.65 Å (Table S3, Figure S4). The structures of the second series contain a inorganic framework similar to those of real t-FA2_2PbBr4_4 but without distortion of octahedral and without tilting (all Pb-Br bonds have the equal length and all Br-Pb-Br and Pb-Br-Pb angles are equal to 90° and 180° respectively). Because the second series have undistorted inorganic framework, all these structures possess only one interlayer distance (dd).

Structured(Br⋯Br)d(\mathrm{Br}\cdots\mathrm{Br}), ÅEgE_{\mathrm{g}}, eV
Structure 13.502.866
Structure 23.872.945
Structure 34.152.978
Structure 44.633.010
Structure 56.003.037
Structure 610.03.042

Table S4. The interlayer distances and calculated band gaps (EgE_{\mathrm{g}}) of corresponding undistorted eclipsed model structures.

Image not extracted

Figure S11. Calculated band structures of the model distorted eclipsed crystal structures of the FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} with different interlayer distances (dd) from 3.5 Å to 10 Å.

Image not extracted

Figure S12. Calculated band structures of the model undistorted eclipsed crystal structures the FA2PbBr4\mathrm{FA}_{2}\mathrm{PbBr}_{4} with different interlayer distances (dd) from 3.5 Å to 10 Å.

Comparison of the FA2_2PbBr4_4 with other bromoplumbate perovskites

Crystal chemical analysis of the specific volumes of moieties

We consider the unit cell volume (VU.C.V_{U.C.}) of a certain structure with formula Am_mPbBrm+2_{m+2} as the sum of 2 volumes:

  1. the total volume of organic cations A+^+ per unit cell – VA+totV_{A^+}^{tot},

  1. the total volume of inorganic framework per unit cell – VPbXtotV_{PbX}^{tot},

The total volumes (VA+totV_{A^+}^{tot}, VPbXtotV_{PbX}^{tot}) are calculated as two sum of the volumes of the A+^+ organic cations and Pb2+^{2+} plus Br−^- anions in certain crystallographic position respectively, as following:

VA+tot=k∑i=1ZVA+i=kzVA+av,V_{A^+}^{tot}=k\sum_{i=1}^{Z}V_{A^+}^{i}=kzV_{A^+}^{av},
VPbXtot=∑i=1ZVPbi+(m+2)∗∑i=1ZVBri=∑VPbXav,V_{PbX}^{tot}=\sum_{i=1}^{Z}V_{Pb}^{i}+(m+2)*\sum_{i=1}^{Z}V_{Br}^{i}=\sum V_{PbX}^{av},

where Z is a number of formula units per unit cell; VA+iV_{A^+}^{i}, VPbXiV_{PbX}^{i} are specific volumes of A+^+, [PbX4_4] respectively. Because VA+iV_{A^+}^{i} usually slightly varies at different positions within one unit cell it is reasonable to use average specific volumes VA+avV_{A^+}^{av}, VSavV_{S}^{av}, VPbXavV_{PbX}^{av}. The fragmentation of the unit cell volume into “partial” specific volumes is performed using Voronoi-Dirichlet polyhedra (see details below), therefore, as a result, the sum of the volumes is equal to the unit cell volume (VA+tot+VPbXtot+VStot=VU.C.V_{A^+}^{tot}+V_{PbX}^{tot}+V_{S}^{tot}=V_{U.C.}).

Details of the volumes calculation by Voronoi-Dirichlet polyhedra

The unit cell of the FA2_2PbBr4_4 crystal structure contains 8 cations of formamidinium (half of these cations are symmetrically nonequivalent due to the fact that the structure was refined in the P1ˉ\bar{1} space group with Z=4). The average volume of the Voronoi-Dirichlet (VVDP) polyhedron per one FA+^+ cation is 96.79 Å3^3 or 774.31 Å3^3 per unit cell (see Figure S8 and Table S5), while the VVDP of the inorganic framework is 497.43 Å3^3 per unit cell.

Comparison of FA+^{+} and [PbX4_4] specific volumes in different crystal structures

Using the average specific volumes of organic cations and inorganic PbX4_4-moieties calculated from as-solved structure of t-FA2_2PbBr4_4, we can compare them with a corresponding specific volumes defined for related compounds described in the literature. In particular, it is reasonable to compare the volume of FA+^{+} cation in the structure of t-FA2_2PbBr4_4 with its volume in the structures of FAPbBr3_3 and FAI, and compare the VPbX4av.V_{\mathrm{PbX_4}}^{av.} for t-FA2_2PbBr4_4 with the same volume in the structures of related 110 bromide perovskites – (Im,Gua)PbBr4_4 and (TzH,Gua)PbBr4_4 in low-temperature (lt) and high-temperature (ht) modifications (Im, Gua and TzH is imidazolium, guanidinium and 1,2,4-triazolium cations respectively).

Image not extracted

Figure S14. The VA+av.V_{A^+}^{av.} and VPbX4av.V_{\mathrm{PbX_4}}^{av.} in different crystal structures

structureVFA+av.V_{\mathrm{FA^+}}^{av.}VPbX4av.V_{\mathrm{PbX_4}}^{av.}
FAI93.37-
FAPbBr3_396.13-
t-FA2_2PbBr4_496.79124.4
lt(Im,Gua)PbBr4_4-125.2
ht(Im,Gua)PbBr4_4-128.8
lt(TzH,Gua)PbBr4_4-128.5
ht(TzH,Gua)PbBr4_4-132.8

Table S6. The specific volumes of FA+^{+} and [PbX4_4] in different crystal structures

As one can see, the difference in the volumes of FA+^{+} cations in three structures does not exceed 2%, and in the case of FAPbBr3_3 the difference is negligible. Similarly, the volume of the inorganic lattice for FA2_2PbBr4_4 is only slightly less than in similar 110 layered perovskites (taking into account that the measurement was carried out at 100 K it is more correct to compare with low-temperature modifications).

Based on this comparison, one can make a solid inference, that the structure of FA2_2PbBr4_4 is completely typical in the terms of specific volumes and density of packing point of view.

Abbreviations for spacing organic cations: N-MEDA = N-methylethane-1,2-diammonium [2]; Tz = [C2_2H4_4N3_3]+^+ = triazolium [3]; EDBE = [NH3_3(CH2_2)2_2O(CH2_2)2_2O(CH2_2)2_2NH3_3]2+^{2+} = 2,2-(ethylenedioxy)-bis(ethylammonium) [4]; 3APy-dp = [(H2_2N(CH2_2)3_3CH)NH3_3]2+^{2+} = [C4_4H10_{10}N2_2]2+^{2+} = diprotonated 3-aminopyrrolidine [5]; 3APIm-dp = [C3_3H4_4N2_2(CH2_2)3_3NH3_3]2+^{2+} = C6_6H13_{13}N3_3 = diprotonated N-(3-aminopropyl)imidazole [6]; EPZ-dp = [(H2_2NC4_4H8_8NH)CH2_2CH3_3]2+^{2+} = C6_6H16_{16}N2_2 = diprotonated 1-ethylpiperazine [7].

The emission band of FA2_2PbBr4_4 has a significantly narrower FWHM of 0.22 eV (52 nm) in comparison with a typical FWHM of bounded excitons induced photoluminescence (Table S7, Table S8). Among the (110) bromoplumbate layered perovskites known so far, only the (Im,Gua)PbBr4_4 has a FWHM of PL emission (0.08 eV) smaller than FA2_2PbBr4_4. Both the compounds have an unusually small degree of PbX6_6 octahedra distortion: Δd\Delta d = 7.6·10−4^{-4} for (Im,Gua)PbBr4_4 and 3.9·10−4^{-4} for FA2_2PbBr4_4 (Table S7).

    • no intrinsic PL, ** - excitonic band, *** - unknown band probably related to surface defects

References

  1. [1]Inada Y., Orita H. Efficiency of numerical basis sets for predicting the binding energies of hydrogen bonded complexes: Evidence of small basis set superposition error compared to Gaussian basis sets // J. Comput. Chem. 2008. Vol. 29, № 2. P. 225–232.pubmed.ncbi.nlm.nih.gov/17565500
  2. [2]Dohner E.R., Hoke E.T., Karunadasa H.I. Self-Assembly of Broadband White-Light Emitters // J. Am. Chem. Soc. 2014. Vol. 136, № 5. P. 1718–1721.DOI
  3. [3]Guo Y.-Y. et al. Structure-directing effects in (110)-layered hybrid perovskites containing two distinct organic moieties // Chem. Commun. 2019. Vol. 55, № 67. P. 9935–9938.DOI
  4. [4]Dohner E.R. et al. Intrinsic White-Light Emission from Layered Hybrid Perovskites // J. Am. Chem. Soc. 2014. Vol. 136, № 38. P. 13154–13157.DOI
  5. [5]Li X. et al. Small Cyclic Diammonium Cation Templated (110)-Oriented 2D Halide (X = I, Br, Cl) Perovskites with White-Light Emission // Chem. Mater. 2019. Vol. 31, № 9. P. 3582–3590.
  6. [6]Li Y.Y. et al. Novel ⟨110⟩ -oriented organic-inorganic perovskite compound stabilized by N-(3-aminopropyl)imidazole with improved optical properties // Chem. Mater. 2006. Vol. 18, № 15. P. 3463–3469.DOI
  7. [7]Mao L. et al. Structural Diversity in White-Light-Emitting Hybrid Lead Bromide Perovskites // J. Am. Chem. Soc. 2018. Vol. 140, № 40. P. 13078–13088.DOI
  8. [8]Mączka M. et al. Layered Lead Iodide of [Methylhydrazinium]2PbI4 with a Reduced Band Gap: Thermochromic Luminescence and Switchable Dielectric Properties Triggered by Structural Phase Transitions // Chem. Mater. 2019. Vol. 31, № 20. P. 8563–8575.DOI
  9. [9]Inada Y., Orita H. Efficiency of numerical basis sets for predicting the binding energies of hydrogen bonded complexes: Evidence of small basis set superposition error compared to Gaussian basis sets // J. Comput. Chem. 2008. Vol. 29, № 2. P. 225–232.pubmed.ncbi.nlm.nih.gov/17565500
  10. [10]Dohner E.R., Hoke E.T., Karunadasa H.I. Self-Assembly of Broadband White-Light Emitters // J. Am. Chem. Soc. 2014. Vol. 136, № 5. P. 1718–1721.DOI
  11. [11]Guo Y.-Y. et al. Structure-directing effects in (110)-layered hybrid perovskites containing two distinct organic moieties // Chem. Commun. 2019. Vol. 55, № 67. P. 9935–9938.DOI
  12. [12]Dohner E.R. et al. Intrinsic White-Light Emission from Layered Hybrid Perovskites // J. Am. Chem. Soc. 2014. Vol. 136, № 38. P. 13154–13157.DOI
  13. [13]Li X. et al. Small Cyclic Diammonium Cation Templated (110)-Oriented 2D Halide (X = I, Br, Cl) Perovskites with White-Light Emission // Chem. Mater. 2019. Vol. 31, № 9. P. 3582–3590.
  14. [14]Li Y.Y. et al. Novel ⟨110⟩ -oriented organic-inorganic perovskite compound stabilized by N-(3-aminopropyl)imidazole with improved optical properties // Chem. Mater. 2006. Vol. 18, № 15. P. 3463–3469.DOI
  15. [15]Mao L. et al. Structural Diversity in White-Light-Emitting Hybrid Lead Bromide Perovskites // J. Am. Chem. Soc. 2018. Vol. 140, № 40. P. 13078–13088.DOI
  16. [16]Mączka M. et al. Layered Lead Iodide of [Methylhydrazinium]2PbI4 with a Reduced Band Gap: Thermochromic Luminescence and Switchable Dielectric Properties Triggered by Structural Phase Transitions // Chem. Mater. 2019. Vol. 31, № 20. P. 8563–8575.DOI

Paper details

vlnc:W_6q9urmpb
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents