betaFeedback

WorksPhysics and Astronomy

High-Performance Ferroelectric Field-Effect Transistors with Ultra-High Current and Carrier Densities

Abstract

Ferroelectric field-effect transistors (FeFET) with two-dimensional (2D) semiconductor channels are promising low-power, embedded non-volatile memory (NVM) candidates for next-generation in-memory computing. However, the performance of FeFETs can be limited by a charge imbalance between the ferroelectric layer and the channel, and for low-dimensional semiconductors, also by a high contact resistance between the metal electrodes and the channel. Here, we report a significant enhancement in performance of contact-engineered FeFETs with a 2D MoS2 channel and a ferroelectric Al0.68Sc0.32N (AlScN) gate dielectric. Replacing Ti with In contact electrodes results in a fivefold increase in on-state current (~120 uA/um at 1 V) and on-to-off ratio (~2*10^7) in the FeFETs. In addition, the high carrier concentration in the MoS2 channel during the on-state (> 10^14 cm^-2) facilitates the observation of a metal-to-insulator phase transition in monolayer MoS2 permitting observation of high field effect mobility (> 100 cm^2V^-1s^-1) at cryogenic temperatures. Our work and devices broaden the potential of FeFETs and provides a unique platform to implement high-carrier-density transport in a 2D channel.

Introduction

The ferroelectric field effect transistor (FeFET) device has garnered attention due to its desirable properties such as a compact, non-volatile memory, high on-to-off current ratio, high access speed, and low programming energy.[1] However, the majority of FeFETs employing conventional semiconductor channels, such as Si, face a significant challenge due to the charge imbalance between the ferroelectric layer and the channel.[2, 3] For example, when Hfx_xZr1−x_{1-x}O2_2, which shows a remnant polarization (PrP_\mathrm{r}) of ∼\sim10–30 μC/cm2^2, is used in the gate stack, the carrier density in the Si channel should ideally reach ∼\sim1014^{14} cm−2^{-2} to achieve a charge balance with the PrP_\mathrm{r} of Hfx_xZr1−x_{1-x}O2_2. However, the carrier concentration in conventional Si channel FeFETs can only reach up to 1–2×1013^{13} cm−2^{-2} due to charge screening by the native SiOx_x interface and the 3D nature of the semiconductor.[2, 3] This results in a large discrepancy in charge density between the channel and Hfx_xZr1−x_{1-x}O2_2.[2] This mismatch causes partial polarization of the FeFETs and the accumulation of trapped carriers at the Si/Hfx_xZr1−x_{1-x}O2_2 interface, resulting in various reliability issues.[2, 4, 5] On the other hand, several reports have highlighted the doping capacity of 2D materials, particularly MoS2_2, in supporting carrier concentration exceeding 1014^{14}–1015^{15} cm−2^{-2}.[6, 7, 8, 9] This is particularly advantageous to mitigate the charge imbalance issue between the ferroelectric and 2D channel material. The substantial capability of 2D MoS2_2 to support higher carrier concentrations owing to its 2D density of states further makes them promising channel material candidates, especially when paired with ferroelectric materials with large PrP_\mathrm{r} in the gate stack.[8, 10, 11, 12, 13, 14, 15]

Recently, Al0.68_{0.68}Sc0.32_{0.32}N (AlScN) has been explored as the ferroelectric material in 2D FeFETs due to its high PrP_\mathrm{r} value (∼\sim80–115 μC/cm2^2) and the feasibility of using a low thermal budget process for back-end-of-line direct integration.[16, 17] The high PrP_\mathrm{r} of AlScN, coupled with the high doping capacity and ultraclean van der Waals interface of 2D MoS2_2, can offer an excellent combination for high-performance FeFETs.[17, 18] Specifically, the carrier density induced by the PrP_\mathrm{r} of AlScN is theoretically ∼\sim5–7×1014^{14} cm−2^{-2} (=Pr/qP_\mathrm{r}/q, where qq = 1.6 × 10−19^{-19} C is the elementary charge),[19] matching well with the doping capacity of MoS2_2 (∼\sim1014^{14}–1015^{15} cm−2^{-2}).[6, 7, 8, 9] However, the reported MoS2_2/AlScN FeFETs[17, 18] may not have fully taken advantage of the high PrP_\mathrm{r} of AlScN due to imperfect metal-semiconductor contacts.[20, 21, 22, 23, 24] For example, high contact resistance results in degradation in sheet conductance, transconductance, and on-state (IonI_\mathrm{on}) and off-state currents (IoffI_\mathrm{off}), ultimately impeding the performance of ultra-scaled 2D devices.[20, 21, 22, 23, 24] Therefore, to fully utilize the high PrP_\mathrm{r} of AlScN, it is important to tackle the persistent challenge of high contact resistance between the 2D channel and contact electrodes. This entails resolving issues such as energy level mismatch at the metal-semiconductor junction (MSJ) interface,[20, 21] high-energy metal deposition processes[22], and chemical reactions of metals with 2D semiconducting transition metal dichalcogenides (TMDs).[20, 24] Moreover, in the case of 2D FeFETs, there have been no systematic investigations into the effects of contact interface on key performance indicators such as Ion/IoffI_\mathrm{on}/I_\mathrm{off}, and programming/erasing voltage.[8] This is particularly significant because low conductance may result in low read current and slow write/erase speed at the same read voltage.[2, 4, 5, 8] Furthermore, ensuring scalable production of low-resistance contact electrodes is crucial for the high reproducibility and reliability of 2D-channel/ferroelectric FeFETs for eventual production and commercialization.

Here, we report the high current and high carrier density in In-contact based MoS2_2 channel FeFETs with AlScN as the ferroelectric. We observe the IonI_\mathrm{on} of In-contacted MoS2_2/AlScN FeFETs approaching ∼300 (∼120) μA/μm at a drain-to-source voltage (VdsV_\mathrm{ds}) of 3 (1) V, resulting in a high Ion/IoffI_\mathrm{on}/I_\mathrm{off} of ∼2 × 107^{7} on average, which is ∼3 times higher than with Ti contacts. Remarkably, IonI_\mathrm{on} (∼100 μA/μm), Ion/IoffI_\mathrm{on}/I_\mathrm{off} (∼2 × 107^{7}), and memory windows normalized by the ferroelectric thickness (∼0.11 V/nm) of the MoS2_2/AlScN FeFETs surpass those reported for any other 2D-channel/ferroelectric FeFETs. In conjunction with the negligible thermal emission barrier height of the In-MoS2_2 MSJ interface, the high PrP_\mathrm{r} of the AlScN enables a significantly large number of carriers to be injected into the monolayer channel (> 4.8 × 1014^{14} cm−2^{-2}) with a high field-effect mobility (∼31 cm2^{2}V−1^{-1}s−1^{-1}). In addition, the large doping capacity enables the observation of a metal-to-insulator phase transition in monolayer MoS2_2, concurrently with a band-like transport as observed in variable temperature measurements further suggesting high doping levels enabled by the high PrP_\mathrm{r} of AlScN. Finally, we have also explored the pulse dynamic characteristics and successfully demonstrated the realization of multilevel conductance states in the FeFETs, which is important for amplifying effective bit density for embedded memory technologies. Notably, our FeFETs with In contact exhibits a larger read current of ∼3.1 (5.2) μA in response to a 0.1 (1.0) ms programming pulse compared to those using Ti contacts, suggesting potential for low-power operation.

RESULTS AND DISCUSSION

FeFETs with different contact interfaces.

Figure 1a illustrates the cross-sectional schematic of the FeFET structure. A MoS2_2 monolayer grown by metal-organic chemical vapor deposition (MOCVD) is utilized as the 2D channel and the AlScN layer, 45 nm thick, acts as an effective ferroelectric gate due to its high PrP_{\mathrm{r}} (∼\sim80–115 μC/cm2\mu\mathrm{C}/\mathrm{cm}^{2}).[16, 17] The applied gate voltage (VgV_{\mathrm{g}}) induces the switching of ferroelectric polarizations in AlScN, resulting in a change of the fermi level (EfE_{\mathrm{f}}) of MoS2_2. This modulation subsequently produces erased or programmed conductance states of the FeFET (Figure 1b). Here, metallic In has been chosen as contact electrodes to integrate with the MoS2_2/AlScN structure with a low contact resistance. This is because In is known to be less chemically reactive with TMDs and has a work function (WF≈4.1W_{\mathrm{F}} \approx4.1 eV) that is smaller than the electron affinity of monolayer MoS2_2 (χ≈4.4\chi\approx4.4 eV), possibly resulting in the a negligible Schottky barrier height at the MSJ interface (i.e., ΦB=WF−χ=−300\Phi_{\mathrm{B}} = W_{\mathrm{F}}-\chi= -300 meV for ideal case).[20, 22] The device fabrication is scalable (see Methods for detail), which allows the successful fabrication of arrays of In-contacted MoS2_2/AlScN FeFETs (Figure 1c). The device dimensions are a channel length (LchL_{\mathrm{ch}}) of ∼\sim300 to 1,500 nm and a width (WchW_{\mathrm{ch}}) of ∼\sim20 μ\mum, as presented in a scanning electron microscopy (SEM) image (Figure 1d).

Structure and electrical properties of a monolayer MoS$_2$/AlScN FeFET

Figure 1. Structure and electrical properties of a monolayer MoS2_2/AlScN FeFET. (a) Schematic diagram of a MoS2_2/AlScN FeFET with In/Au contact electrodes. (b) Illustrations depicting the band bending of monolayer MoS2_2, influenced by the polarization directions (PupP_{\mathrm{up}} or PdnP_{\mathrm{dn}}) of AlScN, which in turn govern the erase/program functions of the FeFET. The polarization bound charges with + or - symbols and mobile electrons are displayed in the bands. (c, d) SEM images of (c) the FeFET arrays and (d) the unit device with a channel width (WchW_{\mathrm{ch}}) of 20 μm. (e, f) Transfer characteristics (IdsI_{\mathrm{ds}}-VgV_{\mathrm{g}}) of the FeFET with In (red) and Ti contact electrodes (blue) under the VdsV_{\mathrm{ds}} of 1 V in the (e) semi-logarithm and (f) linear scales. The transfer curves were recorded at a rate of 10 Hz with a VgV_{\mathrm{g}} spacing of 0.2 V. The differences in the subthreshold voltages (VthV_{\mathrm{th}}) indicate the memory window (MW). (g) Output characteristic (IdsI_{\mathrm{ds}}-VdsV_{\mathrm{ds}}) of FeFET under the VgV_{\mathrm{g}} of 12 V (See Figure S3 for the dependence of output curves on VgV_{\mathrm{g}}.). (h-j) Histograms of (h) VthV_{\mathrm{th}} values showing the memory windows, (i) on-state current density (IonI_{\mathrm{on}}) at VgV_{\mathrm{g}} = 10 V, and (j) IonI_{\mathrm{on}}/IoffI_{\mathrm{off}} values depending on the In (red) and Ti contacts (blue). The performance metrics are extracted using the transfer curves under VdsV_{\mathrm{ds}} of 1 V for devices with a channel length (LchL_{\mathrm{ch}}) of 300-1,500 nm. IonI_{\mathrm{on}}/IoffI_{\mathrm{off}} is the maximum attainable ratio between IonI_{\mathrm{on}} and IoffI_{\mathrm{off}}.

The typical transfer curve of an In-contacted FeFET, measured at VdsV_{\mathrm{ds}} of 1 V in both semilogarithmic and linear scales, is shown as red curves in Figure 1e and Figure 1f, respectively. The transfer characteristic of the FeFET displays a counterclockwise sweep direction with high gate-field modulation (Ion/Ioff>107I_{\mathrm{on}}/I_{\mathrm{off}} > 10^{7}) (Figure 1e), indicating the initiation of the ferroelectric switching mechanism. On the other hand, the MoS2_2 FETs fabricated with a non-ferroelectric (non-Fe) dielectric gate (SiO2_2) shows clockwise hysteresis caused by charge trap effects, further confirming the effect of AlScN (Figure S1). The memory window (MW), extracted by the threshold voltages (VthV_{\mathrm{th}}) shift, is confirmed to be greater than ∼\sim7 V (Figure 1f). To prove the impact of In contacts, the FeFETs are also fabricated with Ti contacts (instead of In) for comparison, and the transfer curve results of the fabricated devices are displayed as blue curves in Figure 1e and f. Ti was selected for the comparison because it is chemically reactive when deposited on MoS2_2, resulting in a degraded MSJ interface with high contact resistance.[20, 25] As proof, a representative Incontacted MoS2_2/AlScN FeFET shows a higher IonI_{\mathrm{on}} of ∼100\sim100 μ\muA/μ\mum than that of Ti-contacted (∼20\sim20 μ\muA/μ\mum) at VdsV_{\mathrm{ds}} of 1 V. Such a high on-state current density in monolayer MoS2_2 can also be realized in an FeFET with thicker AlScN (∼100\sim100 nm), indicating the universality of the In contact for high resistance ratio switching (Figure S2). The representative output characteristics also display ∼6\sim6 times higher saturation current in the FeFETs with In contacts over Ti contacts (Figure 1g and Figure S3). The saturated IdsI_{\mathrm{ds}} of ∼300\sim300 μ\muA/μ\mum is reached at only VdsV_{\mathrm{ds}} of ∼2.7\sim2.7 V for the FeFET with a 300 nm channel length, which is much higher than that of a Ti/MoS2_2/AlScN FeFET (<50< 50 μ\muA/μ\mum). It is worth noting that the saturation IdsI_{\mathrm{ds}} of our In-contacted FeFETs (∼300\sim300 μ\muA/μ\mum) surpasses the highest IdsI_{\mathrm{ds}} (∼250\sim250 μ\muA/μ\mum) reported previously for Ti-contacted MoS2_2/AlScN FeFETs with a 4-times shorter LchL_{\mathrm{ch}} of ∼80\sim80 nm.[18]

Ferroelectric switching mechanism of MoS2/AlScN FeFET with In contacts

Figure S1. Ferroelectric switching mechanism of MoS2/AlScN\mathrm{MoS}_2/\mathrm{AlScN} FeFET with In contacts. (a) Transfer characteristics for various VgV_{\mathrm{g}} sweep ranges (±4\pm4, ±5\pm5, and ±10\pm10 V), all showing counterclockwise hysteresis, as indicated by the arrows. (b) Comparison of the IdsI_{\mathrm{ds}}-VgV_{\mathrm{g}} plots for MoS2\mathrm{MoS}_2 FeFET (red) and standard FET (blue) with VgV_{\mathrm{g}} applied through AlScN (45 nm thickness) and SiO2_2 (50 nm thickness) gate substrates. Both devices were subjected to a VgV_{\mathrm{g}} sweep up to ±12\pm12 V for fair comparison. (c) Zoomed-in transfer curve of the MoS2\mathrm{MoS}_2 FET gated with SiO2_2 non-FE dielectric, from panel (b). The arrows indicate the hysteresis directions.

High-performance of FeFET with a thicker AlScN ferroelectric

Figure S2. High-performance of FeFET with a thicker AlScN ferroelectric. (a) Cross-sectional schematic of the device structure. (b) Transfer and (c) output curves of the 100 nm- and 45-nm thick AlScN-based FeFETs. The output curves are measured under the maximum VgV_g in (b), which is 10 and 14 V for 45 and 100 nm AlScN case, respectively.

Gate-dependent output characteristics of FeFETs with In and Ti contact electrodes

Figure S3. Gate-dependent output characteristics of FeFETs. The output curves (IdsI_{\mathrm{ds}}–VdsV_{\mathrm{ds}}) of MoS2_2/AlScN FeFET with (a) In and (b) Ti contact electrodes. In contact FeFET shows more than five times higher IdsI_{\mathrm{ds}} than Ti contact FeFET when VgsV_{\mathrm{gs}} is 12 V.

To enhance the impact and reproducibility of our results, we investigate the performance of Ti and In contact electrodes on a large number of monolayer MoS2_2/AlScN FeFETs, with over 20 devices tested for each type of contact rather than a comparison from a single representative I-V characteristic. The results are compiled and presented in the form of histograms (Figure 1h-Figure 1j). The results show that devices with In contacts have ∼3\sim3 times higher IonI_{\mathrm{on}} (∼57.7±18.3\sim57.7 \pm18.3 μ\muA/μ\mum) and ∼4\sim4 times better Ion/IoffI_{\mathrm{on}}/I_{\mathrm{off}} (∼2⋅107±1.5\sim2 \cdot10^{7} \pm1.5) than devices with Ti contacts, when averaging 20 devices with LchL_{\mathrm{ch}} varied from ∼300\sim300 to 1,500 nm (Figure 1i, Figure 1j). On the other hand, the MW of the MoS2_2/AlScN FeFET with In contacts (∼4.5±1.2\sim4.5 \pm1.2 V) is smaller compared to the devices with Ti contacts (∼5.4±1.3\sim5.4 \pm1.3 V) (Figure 1h). The smaller MW is a result of the negative shift of VthV_{\mathrm{th}} in the forward sweep, which is caused by the increased efficiency of current injection by the small-work-function In contact that makes it easier for the transistor to switch on.[26, 27] The variability of IonI_{\mathrm{on}} with respect to LchL_{\mathrm{ch}} is characterized by calculating the coefficient of variation (CV = σ/μ\sigma/\mu, where σ\sigma is the standard deviation and μ\mu the mean value) for the In- and Ti-contacted MoS2_2/AlScN FeFETs. The average CV for the In-contacted FeFETs is ∼11.8±6.2%\sim11.8 \pm6.2\%, which is three times smaller than that for the Ti-contacted devices (∼37.8±20.7%\sim37.8 \pm20.7\%) for the devices with the same LchL_{\mathrm{ch}} (∼300\sim300 nm). The observed device-to-device variation is attributed to the non-uniformity of the contact and dielectric interface, as well as local charge inhomogeneities.[28]

Transmission line method for FeFETs.

To investigate the room-temperature electrical properties of the MoS2/AlScN\mathrm{MoS_2/AlScN} FeFETs, contact resistance (RcR_{\mathrm{c}}) and channel’s sheet resistance (RchR_{\mathrm{ch}}) are extracted using the transmission line method (TLM). Figure 2a shows a plot of total resistance normalized by channel width (RWchRW_{\mathrm{ch}}) of the MoS2/AlScN\mathrm{MoS_2/AlScN} FeFETs with In and Ti contacts at VgV_{\mathrm{g}} of 10 V. The averaged RWchRW_{\mathrm{ch}} increases linearly as a function of the LchL_{\mathrm{ch}} according to a relationship as follows:

High resistance ratio switching in the MoS2 FeFET with low contact resistance

Figure 2. High resistance ratio switching in the MoS2MoS_2 FeFET with low contact resistance. (a) Total resistance (RWchRW_{\mathrm{ch}}) of the FeFETs with In and Ti contact electrodes depending on the channel length (LchL_{\mathrm{ch}}) measured at VgV_{\mathrm{g}} of 10 V during the forward sweep in transfer transport. The yy-intercepts and the slope indicate the contact resistance (2Rc2R_{\mathrm{c}}) and the channel sheet resistance (RchR_{\mathrm{ch}}) of the TLM sets, respectively. (b) RcR_{\mathrm{c}} and (c) RchR_{\mathrm{ch}} of In- (red) and Ti-contacted MoS2MoS_2 FeFETs (blue) under the different VgV_{\mathrm{g}} in the forward (solid) and backward sweep (open). (d) Comparison of RchR_{\mathrm{ch}} as a function of RcR_{\mathrm{c}} of few-layer MoS2MoS_2 FETs[21, 22, 23, 24, 29, 30] (circles) and our MoS2MoS_2/AlScN FeFET (stars). The contact electrodes for each FET are labeled. IL stands for interlayer contact. (e, f) Comparisons of (e) IonI_{\mathrm{on}} (normalized at VdsV_{\mathrm{ds}} = 1 V) depending on the channel length (LchL_{\mathrm{ch}}) and (f) IonI_{\mathrm{on}}/IoffI_{\mathrm{off}} and memory window (normalized by the thickness of ferroelectric) for our FeFET (red stars) with the literature values for MoS2MoS_2 FET[6, 20, 21, 22, 23, 36, 37, 38, 40] (open) and MoS2MoS_2 FeFET[10, 11, 31, 32, 33, 34, 35] (solid). Compared values are extracted from the DC measurement for the transfer characteristic of (Fe)FETs. The fitted curve in (e) reveals the ohmic relation of the IonI_{\mathrm{on}} values (Ion∝1/LchI_{\mathrm{on}} \propto1/L_{\mathrm{ch}}). For standard (non-ferroelectric) FETs, the contact electrodes are labeled; and for FeFETs, the ferroelectric material is labeled. The reported performances for the Si-channel HZO FeFETs[41, 42] (purple squares) are also displayed in (f) to compare with 2D MoS2MoS_2-based FeFETs.

RWch=Rch+2Rc;(1)RW_{\mathrm{ch}} = R_{\mathrm{ch}} + 2R_{\mathrm{c}}; \tag*{(1)}
Rch=Lchq⋅n2D⋅μFE(2)R_{\mathrm{ch}} = \frac{L_{\mathrm{ch}}}{q\cdot n_{\mathrm{2D}}\cdot\mu_{\mathrm{FE}}} \tag*{(2)}

Here, μFE\mu_{\mathrm{FE}} is field-effect mobility (=(dIds/dVg)×(Lch/WchCiVds)(\mathrm{d}I_{\mathrm{ds}}/\mathrm{d}V_{\mathrm{g}})\times(L_{\mathrm{ch}}/W_{\mathrm{ch}}C_{\mathrm{i}}V_{\mathrm{ds}}), where Ci=2.5×10−7 F/cm2C_{\mathrm{i}} = 2.5 \times10^{-7}\ \mathrm{F/cm^2} is the dielectric constant of AlScN\mathrm{AlScN}[16, 17]). Using Equation (2), one can obtain $2R_{\mathrm{c}}$ and RchR_{\mathrm{ch}} as they are the yy-intercept and the slope of the RWchRW_{\mathrm{ch}}-LchL_{\mathrm{ch}} plot, respectively (Figure 2a). The calculated on-state RcR_{\mathrm{c}} value of In/MoS2\mathrm{MoS_2} MSJ FeFET approaches ∼\sim4.5 ±\pm 1.9 kΩ⋅μm\Omega\cdot\mu\mathrm{m} at VgV_{\mathrm{g}} of 10 V (average ±\pm standard error from the linear fitting), which is almost two times smaller than that of Ti/MoS2\mathrm{MoS_2} MSJ FeFET (∼\sim8.8 ±\pm 0.9 kΩ⋅μm\Omega\cdot\mu\mathrm{m}) at the same VgV_{\mathrm{g}} (Figure 2b), representing better MSJ interface with In contact. Moreover, the TLM-extracted RchR_{\mathrm{ch}} of In-contacted MoS2\mathrm{MoS_2} FeFET decreases over VgV_{\mathrm{g}}, reaching ∼\sim12.2 ±\pm 2.2 kΩ\Omega/sq at 10 V (Figure 2c). The Ti/MoS2\mathrm{MoS_2} MSJ FeFET, meanwhile, demonstrates a higher on-state RchR_{\mathrm{ch}} (∼\sim19.9 ±\pm 1.3$ kΩ\Omega/sq). When comparing the smaller RcR_{\mathrm{c}} and RchR_{\mathrm{ch}} values with those of FeFETs employing Ti contact electrodes, the effectiveness of carrier transport through the In contact is evident (More explanation on how RcR_{\mathrm{c}} leads to a smaller RchR_{\mathrm{ch}} is provided in the following paragraphs for Figure 3.).

Six-panel plot showing extraction of mobility and carrier density during ferroelectric gating

Figure 3. Extraction of mobility and carrier density during the ferroelectric gating. (a) Field-effect mobility (μFE\mu_{\mathrm{FE}}) of the MoS2_2/AlScN FeFETs with In (red) and Ti contact electrodes (blue) depending on the sweep directions. (b) Extracted carrier density (n2Dn_{\mathrm{2D}}) of the In-contact FeFET depending on VgV_{\mathrm{g}}. The Δn2D,cap\Delta n_{\mathrm{2D,cap}} calculated by the parallel plate capacitance model is displayed as solid gray lines. (c) Electrical polarization (Pr=q⋅Δn2D,feP_{\mathrm{r}} = q \cdot\Delta n_{\mathrm{2D,fe}}) calculated using the difference between n2Dn_{\mathrm{2D}} values (Δn2D,fe\Delta n_{\mathrm{2D,fe}}) of the data and the capacitance model in (b). (d) Comparison of the representative q⋅Δn2D,feq \cdot\Delta n_{\mathrm{2D,fe}} values of the In- and Ti-contacted FeFETs. The arrows indicate forward (dashed line) and backward (straight line) sweep directions during the transfer curve characterizations in Figure 1d, Figure 1e. The lines in (c) and (d) are guides for the eyes. (e-f) Comparisons of the FeFET and standard (non-Fe) FET in terms of (e) transfer characteristic during the backward sweep, and (f) TLM-extracted channel sheet conductance (GchG_{\mathrm{ch}}) as a function of n2Dn_{\mathrm{2D}}. The standard FET has the same device configurations, dimensions, and materials as those in FeFET, except for the gate dielectric; i.e., SiO2_2 instead of AlScN. The n2Dn_{\mathrm{2D}} of FeFET in (f) is calculated by assuming that the intrinsic field-effect mobility (μi\mu_{\mathrm{i}}) calculated for the standard FET is comparable to that of FeFET.

To evaluate the performance of our In-contact FeFETs, we have conducted a comprehensive comparison with other devices reported, considering parameters such as RchR_{\mathrm{ch}}, RcR_{\mathrm{c}}, IonI_{\mathrm{on}}, Ion/IoffI_{\mathrm{on}}/I_{\mathrm{off}}, and MW. Compared to the previous reports of MoS2\mathrm{MoS_2} FETs (with a non-Fe dielectric gate),[21, 22, 23, 24, 29, 30] the on-state RchR_{\mathrm{ch}} of our FeFET is significantly smaller (>> 11.4 kΩ\Omega/sq), even smaller than the quantum resistance (∼h/2e2\sim h/2e^2) (Figure 2d). Even though it has slightly higher RcR_{\mathrm{c}} (∼\sim4.4–17 kΩ⋅μm\Omega\cdot\mu\mathrm{m}) compared to the other studies on standard FETs[21, 22, 23, 24, 29, 30] (∼\sim0.1–5 kΩ⋅μm\Omega\cdot\mu\mathrm{m}), the RchR_{\mathrm{ch}} is lower, indicating significant conductance switching in our FeFETs. Furthermore, our FeFET outperforms all the previously reported MoS2\mathrm{MoS}_{2}-based FeFETs,[10, 11, 31, 32, 33, 34, 35] as demonstrated by its improved IonI_{\mathrm{on}} (solid circles in Figure 2e), Ion/IoffI_{\mathrm{on}}/I_{\mathrm{off}}, and MW values (Figure 2f). In addition, the achieved high IonI_{\mathrm{on}} in our device (∼\sim130 μ\muA/μ\mum) is higher than the previous report for MoS2\mathrm{MoS}_{2} FETs with In contact (Ion≈I_{\mathrm{on}} \approx18 μ\muA/μ\mum)[22] and 2D metal-based contact electrodes (Ion≈I_{\mathrm{on}} \approx0.1-3.4 μ\muA/μ\mum).[20, 36, 37] It is even higher than the FET with substitutionally doped channels (Ion≈I_{\mathrm{on}} \approx0.05-4 μ\muA/μ\mum)[6, 38] and comparable to FETs with semi-metal contacts of Sb (Ion≈I_{\mathrm{on}} \approx124-569 μ\muA/μ\mum)[23] or Bi (Ion≈I_{\mathrm{on}} \approx226 μ\muA/μ\mum)[21] that approach the quantum limit (see Table S1 for more comparisons). Besides, our device has the highest Ion/IoffI_{\mathrm{on}}/I_{\mathrm{off}} (∼\sim2⋅107\cdot10^{7}) and highest normalized MW (∼\sim0.11 V/nm; normalized by the ferroelectric thickness) among MoS2\mathrm{MoS}_{2}-based FeFETs reported to date (Figure 2f),[10, 11, 31, 32, 33, 34, 35] which can provide a better read margin to minimize the error rate for memory applications.[39] The superior performance of our FeFET is not only due to the increased current injection efficiency by the In contact electrodes but also due to the high remnant polarization (Pr≈P_{\mathrm{r}} \approx80-115 μ\muC/cm2^{2}) and large coercive field (Ec≈E_{\mathrm{c}} \approx2-4.5 MV/cm) of the AlScN ferroelectric itself.[17] Theoretically, the PrP_{\mathrm{r}} and EcE_{\mathrm{c}} directly relate with the carrier density induced in the channel, Δn2D,Fe(=Pr/q)\Delta n_{\mathrm{2D,Fe}} (=P_{\mathrm{r}}/q), and the MW (=2Ec×=2E_{\mathrm{c}} \times thickness of the ferroelectric), respectively.[19]

DeviceChannelGate dielectric or ferroelectricContact metal or doping methodRcR_\mathrm{c} (kΩ·μm)n2Dn_{2D} (101210^{12} cm−2^{-2})LchL_\mathrm{ch} (nm)μFE\mu_\mathrm{FE} (cm2^2V−1^{-1}s−1^{-1}) at RTμFE\mu_\mathrm{FE} (cm2^2V−1^{-1}s−1^{-1}) at cryogenic TTIonI_\mathrm{on} (μA·μm) at Vds=1V_\mathrm{ds}=1 VRchR_\mathrm{ch} (kΩ/sq)MW (V/nm)Ion/IoffI_\mathrm{on}/I_\mathrm{off} ratioRef.
FeFETCVD-MoS2_2AlScNIn/Au4.4348030023.8153 (at 30 K)130 (313 at Vds=5V_\mathrm{ds}=5 V)12.20.1110710^7This study
FETCVD-MoS2_2SiO2_2Au + AlOx_x doping0.482018033.5 (intrinsic)N/A3008.1N/A10610^616
FETCVD-MoS2_2SiO2_2PtTe2_216891,5009.7N/A3.436.1N/A10710^717
FETCVD-MoS2_2SiNx_xBi0.1232020055120 (at 77 K)339 at Vds=1.5V_\mathrm{ds}=1.5 V17.9N/A10710^711
FETCVD-MoS2_2SiO2_2In3.351,00028 (at 280 K)93 (at 77 K)1850.6N/A10610^612
FETCVD-MoS2_2HfO2_2Sb0.209301,000 / 400 / 10087 (at 320 K)188 (at 50 K)124 / 268 / 5698N/A10710^75
FETCVD-MoS2_2HfO2_2Graphene5916.577,00017N/A0.1N/AN/A10710^718
FETCVD-MoS2_2SiO2_2Graphene11534,00035N/A5N/AN/A10810^819
FETCVD-MoS2_2SiO2_2Re doping26.256.510,500N/AN/A0.05N/AN/AN/A20
FETCVD-MoS2_2 (monolayer)SiO2_2UHV Au2.751075033 (intrinsic)136 (at 81 K, intrinsic)1230N/AN/A13
FETCVD-MoS2_2SiO2_2Fe doping0.67769005494 (at 100 K)4N/AN/A10810^86
FETExfoliated MoS2_2 (monolayer)SiO2_2Sn2002N/A60105 (at 1.4 K)N/A60N/AN/A21
FETCVD-MoS2_2SiO2_2CuS27.3N/A2000N/AN/A1545N/A10610^622
FETCVD-MoS2_2SiO2_2Ti/Au + Low-T growth4.96.110033N/A14035.3N/A10710^723
FETExfoliated few-layer MoS2_2hBN/SiO2_2MoSe2_2/Ti/Au1.97.940050160 (at 160 K)5930N/A10610^624

Table S1. Table S1. Comparisons of nn-type (FE)-FETs with 2D semiconductor channels. For FeFET with 2D channel, the 3D ferroelectric gate of 0.7Pb(Mg1/3_{1/3}Nb2/3_{2/3})O3_3-0.3PbTiO3_3 (PMN-PT), Bi0.85_{0.85}La0.15_{0.15}Fe0.92_{0.92}Mn0.08_{0.08}O3_3 (BLFMO), CuInP2_2S6_6 (CIPS), poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE)), Hf1−x_{1-x}Zrx_xO2_2 (HZO) were used.

Contact-limited mobility and carrier density.

The current density of a transistor is directly related to mobility (or saturation velocity) and carrier density,[40] hence, to gain a better understanding of performance metrics in our devices, we examine them in this section. First, the two-terminal, field-effect linear mobility (μFE\mu_{\mathrm{FE}}) values of our device with L=1 μmL = 1\,\mu\mathrm{m} are extracted (Figure 3a). The In-contact FeFET exhibits higher μFE\mu_{\mathrm{FE}} than the Ti-contact device, attributed to its better contact interface and lower contact resistance. The degradation of a contact interface by Ti results in an increase in the contact resistivity (ρC\rho_{\mathrm{C}}) and the sheet resistance of MoS2_2 underlying contact metals (RshR_{\mathrm{sh}}; note that this is different from channel resistance, RchR_{\mathrm{ch}}), as; Rc∝ρCRshR_{\mathrm{c}} \propto\sqrt{\rho_{\mathrm{C}}R_{\mathrm{sh}}},[43] as depicted in Figure S4, Figure S4. On the other hand, soft metal In can minimize the degradation of RshR_{\mathrm{sh}} upon metal deposition because the structure of the underlying 2D MoS2_2 can be preserved.[22, 44] Similarly, the contact interfacial issue may reduce the intrinsic mobility of MoS2_2 under the contact (μc\mu_{\mathrm{c}}) by Rsh=1/qncμcR_{\mathrm{sh}} = 1/qn_{\mathrm{c}}\mu_{\mathrm{c}}, where the ncn_{\mathrm{c}} is the sheet carrier density of the semiconductor underneath the contact.[43]

Contact interface effects on device performance

Figure S4. Contact interface effects on device performance. (a, b) Illustration depicting the relationship between contact resistivity (ρC\rho_{\mathrm{C}}) and sheet resistance of MoS2_2 underlying contact metals (RshR_{\mathrm{sh}}), highlighting the degradation of the contact interface by Ti. (c, d) Schematic representations of MSJ barrier heights and width depending on the contact interface. The schematic in (c) illustrates the significantly small thermionic barrier height (ΦB\Phi_{\mathrm{B}}) at the In-MoS2_2 MSJ even at -10 V (~79 meV; erase state), possibly caused by the degenerately doping by the carrier transfer from In to MoS2_2 (n++n^{++}). The diagram on the right in (c) depicts the EFE_{\mathrm{F}} above EcE_{\mathrm{c}}, leading to the dominance of field emission over thermionic emission through the MSJ, which is completely different from the Ti-MoS2_2 MSJ case in (d).

We have also assessed the VgV_{\mathrm{g}}-dependent carrier density (n2Dn_{2\mathrm{D}}) of In-MoS2_2/AlScN FeFETs in the on state by utilizing the TLM-extracted RchR_{\mathrm{ch}} and μFE\mu_{\mathrm{FE}} values (Figure 3b and Figure S5). During the forward sweep, n2Dn_{2\mathrm{D}} in the 2D channel increases with VgV_{\mathrm{g}}. At the moment the sweep direction changes from forward to backward, the n2Dn_{2\mathrm{D}} still increases due to the non-volatility of the ferroelectric polarization, reaching a maximum of ∼4.8×1014 cm−2\sim4.8 \times10^{14}\,\mathrm{cm}^{-2}, when the VgV_{\mathrm{g}} of 10 V gradually reduces to 9.4 V. As VgV_{\mathrm{g}} decreases further from 9.4 V, n2Dn_{2\mathrm{D}} decreases exponentially toward the off state (e.g., n2D≈2.6×1012 cm−2n_{2\mathrm{D}} \approx2.6 \times10^{12}\,\mathrm{cm}^{-2} at Vg=0V_{\mathrm{g}} = 0 V). According to the standard parallel capacitance model (gray curves in Figure 3b), the VgV_{\mathrm{g}}-induced n2Dn_{2\mathrm{D}} in the channel is much larger than what can be achieved solely with the AlScN dielectric gating (i.e., Δn2D,cap=Ci(Vg−Vth)/q\Delta n_{2\mathrm{D},\mathrm{cap}} = C_{\mathrm{i}}(V_{\mathrm{g}}-V_{\mathrm{th}})/q at Vg>VthV_{\mathrm{g}} > V_{\mathrm{th}}). This implies that the PrP_{\mathrm{r}} (=Δn2D,Fe/q= \Delta n_{2\mathrm{D},\mathrm{Fe}}/q) of the ferroelectric AlScN plays a crucial role in the VgV_{\mathrm{g}}-induced electron density in the 2D channel.

Two plots of channel resistivity: panel a, In contact, with axes $\sigma_{\mathrm{ch}}$ (S/cm) and $V_g$ (V), and panel b, Ti contact, with the same axes; both show Backward and Forward curves.

Figure S5. TLM-extracted channel resistivity (σch\sigma_{\mathrm{ch}}) of the MoS2_2/AlScN FeFETs measured at Vds=1V_{\mathrm{ds}} = 1 V. The σch\sigma_{\mathrm{ch}} varied depending on (a) In and (b) Ti contact. The σch\sigma_{\mathrm{ch}} are extracted by excluding VgV_g-dependent RcR_{\mathrm{c}} in their total RR, according to Equation (1) and Equation (2) in the main text.

To determine the 2D carrier density induced solely by the ferroelectric polarization (Δn2D,Fe\Delta n_{2\mathrm{D},\mathrm{Fe}}), we subtracted the Δn2D,cap\Delta n_{2\mathrm{D},\mathrm{cap}} obtained using the capacitance model (gray curves in Figure 3b) from the calculated total n2Dn_{2\mathrm{D}} (data points in Figure 3b). We assume that the simplest case, wherein the increase in IdsI_{\mathrm{ds}} is related to the capacitive and ferroelectric responses,[45, 46, 47] such that the total n2D=Δn2D,cap+Δn2D,Fen_{2D} = \Delta n_{2D,\mathrm{cap}} + \Delta n_{2D,\mathrm{Fe}}. We then scale the resulting Δn2D,Fe\Delta n_{2D,\mathrm{Fe}} values to calculate the ferroelectric polarization, PrP_{\mathrm{r}} values of the FeFET, as Pr=q⋅Δn2D,FeP_{\mathrm{r}} = q \cdot\Delta n_{2D,\mathrm{Fe}} (shown in Figure 3c). For example, the maximum Δn2D,Fe\Delta n_{2D,\mathrm{Fe}} value at VgV_{\mathrm{g}} of 9.4 V (∼4.6×1014 cm−2\sim4.6 \times10^{14}\ \mathrm{cm}^{-2}) corresponds to a q⋅Δn2D,Feq \cdot\Delta n_{2D,\mathrm{Fe}} value of ∼73.7 μC/cm2\sim73.7\ \mu\mathrm{C}/\mathrm{cm}^{2}. Remarkably, the calculated q⋅Δn2D,Feq \cdot\Delta n_{2D,\mathrm{Fe}} value (∼73.7 μC/cm2\sim73.7\ \mu\mathrm{C}/\mathrm{cm}^{2} at 9.4 V) due to ferroelectric polarization in our device is much closer to the reported PrP_{\mathrm{r}} of our AlScN[16, 17] (Pr≈80P_{\mathrm{r}} \approx80–135 μC/cm2\mu\mathrm{C}/\mathrm{cm}^{2}). This indicates that ferroelectric gating in the In-contacted MoS2_2/AlScN FeFETs is effectively supported by the high PrP_{\mathrm{r}} characteristic of AlScN. In addition, the result proves the q⋅Δn2D,Feq \cdot\Delta n_{2D,\mathrm{Fe}} values are also highly dependent on the contact properties. Using Ti as the contact electrode, instead of In, results in a maximum q⋅Δn2D,Feq \cdot\Delta n_{2D,\mathrm{Fe}} value of only ∼26 μC/cm2\sim26\ \mu\mathrm{C}/\mathrm{cm}^{2} (Figure 3d). This suggests that the high RcR_{\mathrm{c}} of the MSJ interface hinders the utilization of the high PrP_{\mathrm{r}} inherent in AlScN[16, 17] (Pr≈80P_{\mathrm{r}} \approx80–135 μC/cm2\mu\mathrm{C}/\mathrm{cm}^{2}). When RcR_{\mathrm{c}} is high, the switching of the MFM capacitor under the contact may be imperfect, resulting in significantly lower partial polarization. The degraded MoS2_2 layer (beneath the contacts) can create multiple trap sites, which may result in a depolarization field that prevents full 2Pr2P_{\mathrm{r}} switching of AlScN.[35]

Given the huge mismatch of PrP_{\mathrm{r}} and carrier density in conventional 3D Si/Hfx_xZr1−x_{1-x}O2_2 FeFETs, leading to substantial charge trapping at the Si/ferroelectric interface and reliability issues,[2] our findings suggest that a 2D channel FeFET with a superior contact interface can support the high carrier densities minimizing imbalance of the charges between channel and ferroelectric materials. The 2D MoS2_2 channel with minimal oxidation,[18] compared to the Si with native oxide,[2, 4, 5, 35] may enable the strong coupling between the ferroelectric polarization and the induced charge in the 2D channel due to the prevention of charge screening from the oxide layer. Moreover, the sub-1 nm thickness of 2D MoS2_2 allows minimal effective body capacitance compared to a 3D semiconductor channel, which can lead to a smaller depolarization field.[48, 49]

Therefore, combinations of high-PrP_{\mathrm{r}} AlScN with ohmic-contact 2D channel FeFETs can lead to significant conductance switching. To demonstrate this even more thoroughly, non-Fe FETs (i.e. standard FETs) with the exact same device configuration, fabrication process and material quality (including contact electrodes, channels, etc.), except for the gate dielectric (i.e., SiO2_2 for FET), are fabricated for a comparison with AlScN/MoS2_2 FeFETs. The representative transfer curves of the standard FET and FeFET are displayed in Figure 3e. Noticeably, the on-state current density of the FeFET is substantially superior to non-Fe FETs, more than an order of magnitude.

Moreover, one can determine the n2Dn_{2D} values in AlScN FeFETs by comparing the standard FETs’ channel conductance (GchG_{\mathrm{ch}}) and the “intrinsic” field-effect mobility (μi<∼1.4 cm2V−1s−1\mu_i < \sim1.4\ \mathrm{cm}^{2}\mathrm{V}^{-1}\mathrm{s}^{-1}), extracted by the TLM method (Figure 3f and Figure S5). The on-state n2Dn_{2D} in the AlScN FeFET calculated in this way is ∼3.7×1014 cm−2\sim3.7 \times10^{14}\ \mathrm{cm}^{-2}, closely aligning with the value obtained in Figure 3b (∼4.8×1014 cm−2\sim4.8 \times10^{14}\ \mathrm{cm}^{-2}), further proving its high doping density induced by the ferroelectric. Even in prior reports, such a high doping capacity in monolayer MoS2_2 (n2D>∼1014 cm−2n_{2D} > \sim10^{14}\ \mathrm{cm}^{-2}) is challenging in traditional FETs with solid-state, non-ferroelectric gate dielectrics (Figure S6 and Table S2).

Benchmark plots of different doping methods and gate field effects on MoS2

Figure S6. Benchmark plots of different doping methods and gate field effects on MoS2_2. (a) Comparison of carrier densities (n2Dn_{2\mathrm{D}}) in MoS2_2 with different thicknesses, under different doping methods, or with gating methods. This highlights the challenge of achieving high doping levels (n2D>∼1014 cm−2n_{2\mathrm{D}} > \sim10^{14}\ \mathrm{cm}^{-2}) in a thinner MoS2_2 as reported in previous studies.[1, 2, 3, 4, 5, 6, 7, 8, 9, 10] (b) Charge density (n2Dn_{2\mathrm{D}}) vs. cryogenic mobility for different gate dielectric layers in transistors with a monolayer (1L) MoS2_2 channel.[5, 6, 8, 9, 11, 12, 13] Each point on the plot is labeled according to the specific gate dielectric type used in the measurements. The dielectric constants (kk) for SiO2_2, HfO2_2, and AlScN are 3.9, 25, and 14, respectively.[14, 15] Note that the dual-gated[9] and defect-healed[8] MoS2_2 are mechanically exfoliated, while others are grown using CVD.[5, 6, 11, 12, 13]

Doping strategyChannelGateContact metalMaximum n2Dn_{2D} (101210^{12} cm−2^{-2})μFE\mu_{\mathrm{FE}} (cm2^2V−1^{-1}s−1^{-1}) at RTμFE\mu_{\mathrm{FE}} (cm2^2V−1^{-1}s−1^{-1}) at cryogenic TTIonI_{\mathrm{on}} (μ\muA·μ\mum) at Vds=1V_{\mathrm{ds}} = 1 VIon/IoffI_{\mathrm{on}}/I_{\mathrm{off}} ratioRchR_{\mathrm{ch}} at RT (kΩ\Omega/sq)Scattering coefficient (γ\gamma)Ref.
AlScN gating1L-MoS2_2 (CVD)AlScNIn/Au48023.8153 (at 30 K)130 (313 at Vds=5V_{\mathrm{ds}} = 5 V)10710^711.3 (TLM) 0.36 (Lch=300L_{\mathrm{ch}} = 300 nm)1.69This study
Electrical double layer gating15 nm MoS2_2Ion gelAu75N/A86 (at 220 K, Hall device)0.8510210^21.2N/A1
Electrical double layer gating20 nm MoS2_2Ion gel (DEME-TSFI) and HfO2_2 dual gateN/A1.4N/A240 (at 20 K, Hall device)N/AN/A2 (at 100 K)N/A2
Alkali intercalationBulk MoS2_2 with K, Cs, LiN/AN/A400–1000N/AN/AN/AN/AN/AN/A3, 4
Contact engineering1L-MoS2_2 (CVD)HfO2_2Sb3087 (at 320 K)188 (at 50 K)56910710^781.85
Substitutional dopingFe-doped MoS2_2SiO2_2Cr/Au765494 (at 100 K)410810^8N/AN/A6
Surface charge transfer dopingOleylamine-doped 70 nm MoS2_2SiO2_2Au1925N/A11.82.9N/AN/A7
Defect healingThiol-treated 1L-MoS2_2SiO2_2Ti/Pd5.7∼\sim30 (81 with four terminal device)∼\sim85 at 10 K (& 320 with four terminal)N/AN/A16.90.728
Dual gate1L MoS2_2SiO2_2 and HfO2_2Au15N/A174 (at 4 K with four terminal device)N/AN/A4.31.49
Solid superionic conductor gateFew-layer MoS2_2LaF3_3 gatingAu4160532 (at 2 K)N/A10410^4–10510^52N/A10

Table S2. Comparisons of doping strategies for 2D MoS2_2.

Low-temperature measurements.

To further understand the transport mechanism, an MoS2_2/AlScN FeFET with In contacts is additionally measured at various temperatures (TT = 13–300 K). Figure 4a demonstrates the transfer curves measured under the same VgV_\mathrm{g} sweep (-10 to 10 V) at TT of 240–300 K. One can observe that the turn-on voltage for electron transport increases, and the subthreshold swing (SS) gets steeper at the higher TT. This is because the required VgV_\mathrm{g} to switch the polarizations in ferroelectric AlScN becomes higher at low TT, resulting in the suppression of both the ferroelectric negative capacitance effect and hole conductance as TT decreases. Conversely, in the TT range of 13–120 K, the SS are almost comparable to each other, and the VthV_\mathrm{th} decreases at higher TT (Figure 4b). In this TT regime, the FET is no longer turned on/off by the ferroelectric switching but controlled by the purely capacitive response from the non-Fe dielectric, which is also indicated in the IdsI_\mathrm{ds}-VgV_\mathrm{g} hysteresis directions depending on TT in Figure S7. Consequently, in the subthreshold regime, the suppression of thermionic emission of the electrons over the Schottky barrier at the MSJ becomes more noticeable as the TT decreases, resulting in the VthV_\mathrm{th} and SS changes.

Low-temperature measurements of FeFETs with its different gating mechanisms

Figure 4. Low-temperature measurements of FeFETs with its different gating mechanisms. (a, b) Transfer curves of the same FeFET measured at temperatures of (a) T=240T = 240–300300 K and (b) 1313–120120 K, during the backward sweep. Inset shows the zoomed-in plots in a linear scale near the VgV_{\mathrm{g}} range that shows metal-insulator electrical phase transition (MIT). (c) TT-dependent channel conductance (GG) at the applied VgV_{\mathrm{g}} of 1010 (red) and −10-10 V. The negative slope (dG/dT<0\mathrm{d}G/\mathrm{d}T < 0) indicates its metallic behavior whereas the positive slope (dG/dT>0\mathrm{d}G/\mathrm{d}T > 0) implies its insulating property. (d, e) Extracted dG/dT\mathrm{d}G/\mathrm{d}T depending on the applied VgV_{\mathrm{g}}, at (d) T=240T = 240–300300 K and (e) 1313–120120 K. The specific VgV_{\mathrm{g}} that enables the MIT where the dR/dT≈0\mathrm{d}R/\mathrm{d}T \approx0 is labeled as VMITV_{\mathrm{MIT}}. (e) TT-dependent μFE\mu_{\mathrm{FE}} of three FeFET devices, with the fitted phonon scattering model (μ∝T−1.7\mu\propto T^{-1.7}). (f, g) Extraction of the effective thermionic barrier height (ΦB\Phi_{\mathrm{B}}) at the metal-semiconductor junction between the MoS2_2 and In contact. (f) Arrhenius plot (ln⁡(Ids/T3/2\ln(I_{\mathrm{ds}}/T^{3/2} vs. 1/kBT1/k_{\mathrm{B}}T) to calculate the ΦB\Phi_{\mathrm{B}} values The negative slopes indicate the absence of ΦB\Phi_{\mathrm{B}} (<0< 0), which is the case for VgV_{\mathrm{g}} measured at −7-7 to 1010 V. (g) Extracted ΦB\Phi_{\mathrm{B}} depending on the VgV_{\mathrm{g}}. The inset shows the zoomed-in curve for the VgV_{\mathrm{g}} range of −4-4 to 1010 V, displaying the negative ΦB\Phi_{\mathrm{B}} for Vg>4V_{\mathrm{g}} > 4 V.

Figure 4c displays TT-dependent channel conductance (GG) at VgV_\mathrm{g} of -10 V (blue) and 10 V (red). First, we can observe that the slope of the curve changes around 200 K to some extent, indicating the transition from the non-Fe to Fe gating mechanism of the transistor. Besides, at a VgV_\mathrm{g} of -10 V, the GG decreases when the TT decreases, as expected for temperature-dependent thermionic emission in insulators (dR/dT>0\mathrm{d}R/\mathrm{d}T > 0, blue). Conversely, at a VgV_\mathrm{g} of 10 V, the GG improves when the TT declines (dR/dT<0\mathrm{d}R/\mathrm{d}T < 0, red), probably due to the injected higher carriers, indicating its metallic phase. Even for monolayer MoS2_2 transistors with strongly suppressed carrier scattering, a high carrier density greater than n2D∼1013n_\mathrm{2D} \sim10^{13} cm−2^{-2} (or Rch<0.8h/e2R_\mathrm{ch} < 0.8h/e^2; which is the case in our device as shown in Figure 2d) in a 2D channel is possible, which leads to a critical point that shows the transition between the insulating phase to the metallic phase.[50, 51, 52]

Accordingly, this metal-to-insulator (MIT) behavior does provide a good indication of gating-induced doping capacity to reach n2D∼1013n_\mathrm{2D} \sim10^{13} cm−2^{-2} (based on the theory[50, 51, 52]). We extract dR/dT\mathrm{d}R/\mathrm{d}T depending on VgV_\mathrm{g} at different TT regimes (Figure 4d), and here, the VgV_\mathrm{g} at which MIT occurs, or VMITV_\mathrm{MIT}, is the point at which dR/dT\mathrm{d}R/\mathrm{d}T changes from negative to positive. Noticeably, the VMITV_\mathrm{MIT} is ∼\sim1 V at T>T > 240 K, whereas VMITV_\mathrm{MIT} is ∼\sim4 V for T<T < 120 K, suggesting that Fe gating can support larger n2Dn_\mathrm{2D} than non-Fe gating and trigger band-like transport in the 2D channel.[50, 51, 52, 53] Note that the VMITV_{\mathrm{MIT}} is ~1 V at T>240T > 240 K which is close to the voltage range where the n2Dn_{\mathrm{2D}} reaches the ~101310^{13} cm−2^{-2} in Figure 3b, indicating their consistency.

The high n2Dn_{\mathrm{2D}}-induced band-like transport is also supported by the observation of linear mobility evolution following the phonon-limited carrier transport model of μ∝T−γ\mu\propto T^{-\gamma} with a γ=1.7\gamma= 1.7 for T>200T > 200 K (Figure 4e). This extracted γ\gamma value is comparable to the theoretical exponent γ\gamma for monolayer MoS2_2 (γ=1.7\gamma= 1.7) with the optical phonon scattering, not suppressed by other variations such as Schottky barriers.[50, 53] The consistency of TT-dependent μFE\mu_{\mathrm{FE}} has been verified across three different devices in Figure 4e. In spite of device-to-device variations, all devices display carrier transport characterized by the same exponent γ=1.7\gamma= 1.7, maintaining consistency at T=200T = 200-300 K, where ferroelectric gating affects the carrier injection. Given that this phonon-limited transport mechanism can be exclusively observed in MoS2_2 FETs with dual gates or with ultra-low contact resistance,[23, 50] our approach indicates that AlScN-based gating can provide a useful platform to enable high-mobility, high-carrier density 2D channel devices on a large scale. For example, μFE\mu_{\mathrm{FE}} over 100 cm2^{2}V−1^{-1}s−1^{-1} is observed at low temperatures in two devices (i.e., ~114 and 116 cm2^{2}V−1^{-1}s−1^{-1} for Device 1 and 3, respectively, at 13 K in Figure 4e. Refer to comparisons with previous reports in Figure S6 and Table S2). It is worth noting that the field-effect mobility stays high at large carrier densities suggesting the ability of ferroelectric polarization to effectively screen charged impurity scattering from defects and interfaces. On the other hand, below 120-200 K, the mobility starts to saturate mostly limited by Coulomb scattering of defects. This saturation is also largely affected by the absence of a contribution from the ferroelectric switching to the carrier transport.

The effectiveness of transport through the AlScN-based FeFET with a high-quality contact interface is further confirmed by its smaller effective thermionic barrier height (ΦB\Phi_{\mathrm{B}}) for electrons to overcome (Figure 4f,Figure 4g), extracted by the following equation:

Ids=[AA∗T3/2exp⁡(−qΦBkBT)][exp⁡(qVdskBT)−1](3)I_{\mathrm{ds}} = \left[AA^{*}T^{3/2}\exp\left(-\frac{q\Phi_{\mathrm{B}}}{k_{\mathrm{B}}T}\right)\right]\left[\exp\left(\frac{qV_{\mathrm{ds}}}{k_{\mathrm{B}}T}\right)-1\right] \tag*{(3)}

Here, AA is the junction area, and A∗A^{*} is the effective Richardson–Boltzmann constant. Hence, the value of ΦB\Phi_{\mathrm{B}} can be obtained from the slope of the linear fit to the Arrhenius plot (ln⁡(Ids/T3/2)\ln(I_{\mathrm{ds}}/T^{3/2}) vs. 1/kBT1/k_{\mathrm B}T) as depicted in Figure 4f. The calculated ΦB\Phi_{\mathrm B}-VgV_{\mathrm g} plot suggests that ΦB\Phi_{\mathrm B} is substantially small even at -10 V (~79 meV) (Figure 4g). This is even smaller than those of the In (~375 meV)[22] and Bi contact (~130 meV),[21] and comparable to the Sb contact (~53 meV)[23] for MoS2_2 FET in the completely off state. Moreover, at VgV_{\mathrm g} above -7 V (even in the subthreshold regime), the ΦB\Phi_{\mathrm B} values are negative (Figure 4g and its inset), indicating the large field emission, rather than thermionic emission, through the MSJ (as depicted in Figure S4, Figure S4).

Pulse measurements.

Lastly, we evaluate the resistive switching and the retention of In-contacted MoS2_2/AlScN FeFET, by applying a voltage pulse at the gate (VgV_\mathrm{g}). Figure 5a shows the time retention characteristics of binary states. Two distinct current states with a program/erase over 10410^{4} at Vg=0V_\mathrm{g}=0 V and Vds=0.1V_\mathrm{ds}=0.1 V are achieved after poling the polarization of AlScN up and down by a 1 s program pulse VgV_\mathrm{g} of ±12 V. It is found that varying the program pulse amplitude induces various IdsI_\mathrm{ds}, offering the possibility of multilevel storage in the FeFET, beyond simple binary states. Figure 5b (and Figure S8) shows the multilevel conductance stored after each VgV_\mathrm{g} pulse with different amplitude from -12 to 12 V (with 0.5 V differences) and a width of 1 ms. The different IdsI_\mathrm{ds} are recorded depending on the VgV_\mathrm{g}, and the programming of IdsI_\mathrm{ds} is possible under a VgV_\mathrm{g} bigger than 6.5 V. The stepwise program state is clearly distinct for a total of 58 levels stored at a Vg>6.5V_\mathrm{g}>6.5 V with increasing pulse numbers, promising its 5-bit operation.

Memory retention and programming speed characterizations at room temperature

Figure 5. Memory retention and programming speed characterizations at room temperature. (a) Retention properties of the MoS2_2/AlScN FET with In contact electrodes, at the program and erase states in response to VgV_\mathrm{g} pulses with an amplitude of 12 V and width of 1 s. IdsI_\mathrm{ds} values were recorded at Vds=0.1V_\mathrm{ds} = 0.1 V and Vg=0V_\mathrm{g} = 0 V. (b) Multiple IdsI_\mathrm{ds} states programmed/erased under the pulse train with different amplitudes from Vg=−12V_\mathrm{g} = -12 to 12 V with a pulse width (twidtht_\mathrm{width}) of 50 ms. IdsI_\mathrm{ds} were probed at Vds=1V_\mathrm{ds} = 1 V and Vg=0V_\mathrm{g} = 0 V after applying for program/erase pulse. (c, d) Program state currents of the FeFETs with different contact electrodes, as a function of VgV_\mathrm{g} pulse amplitude. The programming twidtht_\mathrm{width} was 1 ms and 0.1 ms in the case of (c) and (d), respectively.

Evaluation of $I_{\mathrm{ds}}$ reconfigurability in In-contacted MoS$_2$/AlScN FeFET

Figure S8. Evaluation of IdsI_{\mathrm{ds}} reconfigurability in In-contacted MoS2_2/AlScN FeFET. Multilevel conductance stored after each VgV_{\mathrm{g}} pulse, as depicted in (a, b), with varying amplitudes from −12 to 12 V (with 0.5 V differences) and a width of 50 ms. The read IdsI_{\mathrm{ds}} are depicted in (c, d) linear and (e, f) log scale. The recording of different IdsI_{\mathrm{ds}} depending on VgV_{\mathrm{g}} indicates the feasibility of programming IdsI_{\mathrm{ds}} under a VgV_{\mathrm{g}} greater than ∼6.5\sim6.5 V. A stepwise program state is clearly discernible for a total of 58 levels stored at Vg>6.5V_{\mathrm{g}} > 6.5 V with increasing pulse numbers, suggesting its 5-bit operation potential.

The programming speeds of FeFET are further estimated by measuring the VgV_\mathrm{g} pulse-width dependence of the IdsI_\mathrm{ds}. Figure 5c, Figure 5d illustrate the detailed program characteristics of the FET examined by varying pulse amplitude (VgV_\mathrm{g} ranging from 4 to 12 V) and width (twidtht_\mathrm{width} of 0.1 and 1.0 ms). As the VgV_\mathrm{g} amplitude increases, the corresponding IdsI_\mathrm{ds} increase gradually as a response from the AlScN ferroelectric polarization switching, where IdsI_\mathrm{ds} is higher for In-MoS2_2 FeFETs than Ti-contacted ones in both twidtht_\mathrm{width} cases contributed from its larger n2Dn_\mathrm{2D} induced at the same VgV_\mathrm{g}. This suggests that In-contact FeFETs can use a lower pulse amplitude or smaller pulse width compared to Ti-FeFETs to complete the switching for the same program state, demonstrating the great potential of FeFETs for low-power and high-speed non-volatile memory applications.

Conclusion

In summary, the impacts of contact resistance on the monolayer MoS2/AlScN\mathrm{MoS}_2/\mathrm{AlScN} FeFETs are investigated with In contact electrodes. High saturated current density (∼320 μA/μm\sim320\ \mu\mathrm{A}/\mu\mathrm{m} at Vds=3 VV_{\mathrm{ds}} = 3\ \mathrm{V}), Ion/Ioff>107I_{\mathrm{on}}/I_{\mathrm{off}} > 10^{7}, and normalized MW >0.11 V/nm> 0.11\ \mathrm{V}/\mathrm{nm} are achieved in the FeFET. This achievement is attributed to the low contact resistance at the In/MoS2\mathrm{MoS}_2 MSJ interface down to ∼4.4 kΩ⋅μm\sim4.4\ \mathrm{k}\Omega\cdot\mu\mathrm{m}, coupled with high remnant polarization, PrP_{\mathrm{r}}, of AlScN. Consequently, a significantly large carrier density approaching ∼4.8×1014 cm−2\sim4.8 \times10^{14}\ \mathrm{cm}^{-2} is obtained, corresponding to a partially switched PrP_{\mathrm{r}} value of ∼73.7 μC/cm2\sim73.7\ \mu\mathrm{C}/\mathrm{cm}^{2}. Furthermore, the high doping concentration induced by the ferroelectric allows for observation of nearly ideal phonon-limited transport (with an exponent γ\gamma of 1.7) with field-effect mobilities >100 cm2V−1s−1> 100\ \mathrm{cm}^{2}\mathrm{V}^{-1}\mathrm{s}^{-1} at cryogenic temperatures. In addition, pulse measurements conducted in FeFETs demonstrate the realization of 58 conductance levels. We have observed that the stored IdsI_{\mathrm{ds}} values in In-contacted FeFETs surpass those of Ti-contacted devices under the same program pulse amplitude and width. Therefore, our findings present a reproducible approach for achieving the high-current-density and high-mobility 2D channel AlScN FeFETs. Moreover, the low contact resistance and reconfigurable operations of the studied FeFETs make them suitable for integration into low-power electronics, offering potential additional functionalities.

Methods

Device fabrication.

Al0.68Sc0.32N\mathrm{Al}_{0.68}\mathrm{Sc}_{0.32}\mathrm{N} with a thickness of 45 nm was deposited on pre-deposited Pt using a pulsed-DC reactive sputtering deposition system (Evatec, CLUSTERLINE 200 II pulsed DC PVD).[16, 17] The co-sputtering was conducted using separate 4-inch Al and Sc targets, at a chuck temperature of 350 °C, with 10 sccm of Ar gas flow and 25 sccm of N2\mathrm{N}_2 gas flow under the constant pressure of ∼1.45×10−3\sim1.45 \times10^{-3} bar, which is the same as that utilized in our previous reports for FeFETs.[15, 18] The preferentially oriented (111) Pt layer promoted the growth of AlScN with highly textured ferroelectricity along the [1] direction. MOCVD-grown monolayer MoS2\mathrm{MoS}_2 thin film was then transferred from its growth substrate of sapphire to as-grown AlScN using KOH-based wet transfer. A polymeric supporting layer of polymethyl methacrylate (PMMA) was coated on the MoS2MoS_2/sapphire and then floated onto 0.1 M KOH solution to detach MoS2MoS_2 from the sapphire substrate. The detached PMMA/MoS2MoS_2 free-standing layer was rinsed in distilled ionized water several times to avoid any damage to AlScN from the KOH-based residues. After the transfer of PMMA/MoS2MoS_2 to AlScN, the PMMA was removed by acetone for 10 min. The integration process for the monolayer MoS2MoS_2/AlScN FeFETs necessitates the prevention of any high-energy process, thermal budget above 180 °C, and exposure to basic solution to ensure high-quality FeFETs. Source and drain contact of In/Au (10/40 nm) were defined through e-beam lithography (Elionix ELS-7500EX) followed by thermal evaporation (Kurt J. Lesker Nano-36). In particular, the deposition rate for In metal should be adjusted to below 0.03 Å/s to minimize any high-energy damage to the MoS2MoS_2 surface during the thermal evaporation and to pursue small contact resistance[22]. It should be noted that, in this work, the Ti- and In-contacted FeFET arrays were fabricated on the same AlScN substrate with the same MOCVD-grown MoS2MoS_2 film, thereby there were fewer variations in the materials and the channel/dielectric interface. The channel-defining process was conducted using the reactive ion etcher (RIE) with oxygen gas (Jupiter II RIE Plasma Etcher). The Pt beneath the AlScN was used as a gate contact, where the gate contact region was exposed via the wet etching of AlScN on the substrate by dipping it in the KOH solution after the fabrication of the In/MoS2MoS_2/AlScN/Pt heterostructure. No additional heat treatment was conducted after the device fabrication.

Device characterization.

Room-temperature electrical measurements were conducted in the air at ambient temperature in a Lakeshore probe station using a Keithley 4200A semiconductor analyzer. Low-temperature electrical measurements were carried out by a Keithley 4200A semiconductor parameter analyzer in a closed-cycle cryogenic probe station (Advanced Research Systems, Inc.) with a base pressure of ~10−610^{-6} torr. All statistically estimated values in the paper are reported as "average ±\pm standard deviation," unless otherwise specified. SEM was used to capture images at 5 keV with the backscattered detector (TESCAN S8000X).

ASSOCIATED CONTENT

Supporting information with Figure S1-8 and Table S1-2

AUTHOR INFORMATION

Author Contributions.

S. Song and K.-H. Kim contributed equally to this work.

S. S., K.-H. K. and D. J. conceived the experiments and wrote the manuscript with input from all authors. S. S., R. K., and M. D. conducted the low-temperature measurements. N. T., C. C., and J. M. R. grew the MoS2MoS_2. R.K. and M.D. assisted with cryogenic transport measurements. J. Z., and R. H. O. conducted the AlScN deposition and characterization.

CONFLICT OF INTEREST

The authors declare no conflict of interest.

DATA AVAILABILITY STATEMENT

The data that support the findings of this study are available from the corresponding author upon reasonable request.

ACKNOWLEDGMENT

D.J. and S.S. acknowledge primary support from the Office of Naval Research (ONR) Nanoscale Computing and Devices program (N00014-24-1-2131). D.J. and K.H-K acknowledge partial support from the Air Force Office of Scientific Research (AFOSR) GHz-THz program grant number FA9550-23-1-0391. S.S. acknowledges partial support for this work by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (Grant No. 2021R1A6A3A14038492). M.D. and R.K. acknowledge funding from DOE grant DE-SC0023224. A portion of the sample fabrication, assembly and characterization were carried out at the Singh Center for Nanotechnology at the University of Pennsylvania, which is supported by the National Science Foundation (NSF) National Nanotechnology Coordinated Infrastructure Program grant NNCI-1542153. The MOCVD MoS2_2 samples were grown in the 2D Crystal Consortium Materials Innovation Platform (2DCC-MIP) facility at Penn State which is supported by the National Science Foundation under cooperative agreement DMR-2039351.

Transition of FET behavior with various $T$

Figure 7. Transition of FET behavior with various TT. The conductance switching by field effect transitions from Fe gating to gating by non-Fe dielectric capacitance, with corresponding changes in IdsI_{\mathrm{ds}}-VgV_{\mathrm{g}} hysteresis directions, depending on TT, i.e., counterclockwise direction at (a) 300 K, (b) 260 K, and (c) 200 K, and clockwise direction at (d) 160 K, (e) 120 K, (f) 13 K.

Exfoliated few-layer MoS2_2LaF3_3 gating (solid superionic conductor)N/A41N/A60532 (at 2 K)N/A2104^{4}-105^{5}10
FeFETExfoliated InSeCIPSIn/AuN/A10,000728N/A0.140.03106^{6}25
CVD-MoS2_2C60_{60}-doped P(VDF-TrFE)Cr/Au25,00030.2N/A0.006 at Vds=0.2V_{\mathrm{ds}} = 0.2 V0.059106^{6}26
Exfoliated MoS2_2 (13 nm)Al2_2O3_3/BLFMoAu20,000N/A3.30.060105^{5}27
Exfoliated MoS2_2 (6 nm)Al2_2O3_3/HZOTi/Au2,000N/A30 at Vds=0.5V_{\mathrm{ds}} = 0.5 V0.0375107^{7}28
CVD-MoS2_2PMN-PTNi/Au5,000N/A2.08N/A0.0002106^{6}29
Exfoliated MoS2_2 (7 nm)CIPSNi1,000N/A0.19 at Vds=0.1V_{\mathrm{ds}} = 0.1 V0.015104^{4}30
Exfoliated MoSe2_2P(VDF-TrFE)Ti/Au5,0006.77N/A0.001 at Vds=0.1V_{\mathrm{ds}} = 0.1 V0.08104^{4}31
Exfoliated MoS2_2 (4.62 nm)P(VDF-TrFE)Cr/Au3,30095.6N/A2.5 at Vds=2V_{\mathrm{ds}} = 2 V0.08107^{7}32
CVD-MoS2_2HZOTi/Au1,000N/A0.01 at Vds=1V_{\mathrm{ds}} = 1 V0.066106^{6}33

Table 1.

Supporting References

  1. Zhang, Y., Ye, J., Matsuhashi, Y. & Iwasa, Y. Ambipolar MoS2 Thin Flake Transistors. Nano Letters 12, 1136-1140 (2012). https://doi.org:10.1021/nl2021575

  1. Ye, J. T. et al. Superconducting Dome in a Gate-Tuned Band Insulator. Science 338, 1193-1196 (2012). https://doi.org:doi:10.1126/science.1228006

  1. Woollam, J. A. & Somoano, R. B. Superconducting critical fields of alkali and alkaline-earth intercalates of MoS2\mathrm{MoS}_2. Physical Review B 13, 3843-3853 (1976). https://doi.org:10.1103/PhysRevB.13.3843

  1. Somoano, R. B., Hadek, V. & Rembaum, A. Alkali metal intercalates of molybdenum disulfide. The Journal of Chemical Physics 58, 697-701 (1973). https://doi.org:10.1063/1.1679256

  1. Li, W. et al. Approaching the quantum limit in two-dimensional semiconductor contacts. Nature 613, 274-279 (2023). https://doi.org:10.1038/s41586-022-05431-4

  1. Li, H. et al. Reducing Contact Resistance and Boosting Device Performance of Monolayer MoS2 by In Situ Fe Doping. Advanced Materials 34, 2200885 (2022). https://doi.org:https://doi.org/10.1002/adma.202200885

  1. Lockhart de la Rosa, C. J. et al. Molecular doping of MoS2 transistors by self-assembled oleylamine networks. Applied Physics Letters 109 (2016). https://doi.org:10.1063/1.4972781

  1. Yu, Z. et al. Towards intrinsic charge transport in monolayer molybdenum disulfide by defect and interface engineering. Nature Communications 5, 5290 (2014). https://doi.org:10.1038/ncomms6290

  1. Radisavljevic, B. & Kis, A. Mobility engineering and a metal–insulator transition in monolayer MoS2. Nature Materials 12, 815-820 (2013). https://doi.org:10.1038/nmat3687

  1. Wu, C.-L. et al. Gate-Induced Metal–Insulator Transition in MoS2 by Solid Superionic Conductor LaF3. Nano Letters 18, 2387-2392 (2018). https://doi.org:10.1021/acs.nanolett.7b05377

  1. Shen, P.-C. et al. Ultralow contact resistance between semimetal and monolayer semiconductors. Nature 593, 211-217 (2021). https://doi.org:10.1038/s41586-021-03472-9

  1. Wang, Y. et al. Van der Waals contacts between three-dimensional metals and two-dimensional semiconductors. Nature 568, 70-74 (2019). https://doi.org:10.1038/s41586-019-1052-3

  1. English, C. D., Shine, G., Dorgan, V. E., Saraswat, K. C. & Pop, E. Improved Contacts to MoS2 Transistors by Ultra-High Vacuum Metal Deposition. Nano Letters 16, 3824-3830 (2016). https://doi.org:10.1021/acs.nanolett.6b01309

References

  1. [1]Khan, A. I., Keshavarzi, A. & Datta, S. The future of ferroelectric field-effect transistor technology. Nature Electronics 3, 588-597 (2020). https://doi.org:10.1038/s41928-020-00492-7DOI
  2. [2]Toprasertpong, K., Takenaka, M. & Takagi, S. On the strong coupling of polarization and charge trapping in HfO2/Si-based ferroelectric field-effect transistors: overview of device operation and reliability. Applied Physics A 128 (2022). https://doi.org:10.1007/s00339-022-06212-6DOI
  3. [3]Kim, K.-H., Karpov, I., Olsson, R. H. & Jariwala, D. Wurtzite and fluorite ferroelectric materials for electronic memory. Nature Nanotechnology 18, 422-441 (2023). https://doi.org:10.1038/s41565-023-01361-yDOI
  4. [4]Ni, K. et al. Critical Role of Interlayer in Hf0.5Zr0.5O2 Ferroelectric FET Nonvolatile Memory Performance. IEEE Transactions on Electron Devices 65, 2461-2469 (2018). https://doi.org:10.1109/ted.2018.2829122DOI
  5. [5]Deng, S., Liu, Z., Li, X., Ma, T. P. & Ni, K. Guidelines for Ferroelectric FET Reliability Optimization: Charge Matching. IEEE Electron Device Letters 41, 1348-1351 (2020). https://doi.org:10.1109/led.2020.3011037DOI
  6. [6]Li, H. et al. Reducing Contact Resistance and Boosting Device Performance of Monolayer MoS2 by In Situ Fe Doping. Advanced Materials 34, 2200885 (2022). https://doi.org:https://doi.org/10.1002/adma.202200885
  7. [7]Xu, K. & Fullerton-Shirey, S. K. Electric-double-layer-gated transistors based on two-dimensional crystals: recent approaches and advances. Journal of Physics: Materials 3, 032001 (2020). https://doi.org:10.1088/2515-7639/ab8270DOI
  8. [8]Luo, Z.-D., Yang, M.-M., Liu, Y. & Alexe, M. Emerging Opportunities for 2D Semiconductor/Ferroelectric Transistor-Structure Devices. Advanced Materials 33, 2005620 (2021). https://doi.org:https://doi.org/10.1002/adma.202005620
  9. [9]Li, X. et al. Nonvolatile Electrical Valley Manipulation in WS2 by Ferroelectric Gating. ACS Nano 16, 20598-20606 (2022). https://doi.org:10.1021/acsnano.2c07469DOI
  10. [10]Li, C. et al. High-Performance C60 Coupled Ferroelectric Enhanced MoS2 Nonvolatile Memory. ACS Applied Materials & Interfaces 15, 16910-16917 (2023). https://doi.org:10.1021/acsami.3c02610DOI
  11. [11]Si, M., Liao, P.-Y., Qiu, G., Duan, Y. & Ye, P. D. Ferroelectric Field-Effect Transistors Based on MoS2 and CuInP2S6 Two-Dimensional van der Waals Heterostructure. ACS Nano 12, 6700-6705 (2018). https://doi.org:10.1021/acsnano.8b01810DOI
  12. [12]Tong, L. et al. 2D materials&#x2013;based homogeneous transistor-memory architecture for neuromorphic hardware. Science 373, 1353-1358 (2021). https://doi.org:doi:10.1126/science.abg3161
  13. [13]Wang, X. et al. Van der Waals engineering of ferroelectric heterostructures for long-retention memory. Nature Communications 12, 1109 (2021). https://doi.org:10.1038/s41467-021-21320-2DOI
  14. [14]Luo, Z.-D. et al. Dual-Ferroelectric-Coupling-Engineered Two-Dimensional Transistors for Multifunctional In-Memory Computing. ACS Nano 16, 3362-3372 (2022). https://doi.org:10.1021/acsnano.2c00079DOI
  15. [15]Kim, K.-H. et al. Tuning Polarity in WSe2/AlScN FeFETs via Contact Engineering. ACS Nano 18, 4180-4188 (2024). https://doi.org:10.1021/acsnano.3c09279DOI
  16. [16]Liu, X. et al. Aluminum scandium nitride-based metal–ferroelectric–metal diode memory devices with high on/off ratios. Applied Physics Letters 118 (2021). https://doi.org:10.1063/5.0051940DOI
  17. [17]Liu, X. et al. Post-CMOS Compatible Aluminum Scandium Nitride/2D Channel Ferroelectric Field-Effect-Transistor Memory. Nano Letters 21, 3753-3761 (2021). https://doi.org:10.1021/acs.nanolett.0c05051DOI
  18. [18]Kim, K.-H. et al. Scalable CMOS back-end-of-line-compatible AlScN/two-dimensional channel ferroelectric field-effect transistors. Nature Nanotechnology (2023). https://doi.org:10.1038/s41565-023-01399-yDOI
  19. [19]Toprasertpong, K., Takenaka, M. & Takagi, S. Memory Window in Ferroelectric Field-Effect Transistors: Analytical Approach. IEEE Transactions on Electron Devices 69, 7113-7119 (2022). https://doi.org:10.1109/TED.2022.3215667DOI
  20. [20]Song, S. et al. Atomic transistors based on seamless lateral metal-semiconductor junctions with a sub-1-nm transfer length. Nature Communications 13, 4916 (2022). https://doi.org:10.1038/s41467-022-32582-9DOI
  21. [21]Shen, P.-C. et al. Ultralow contact resistance between semimetal and monolayer semiconductors. Nature 593, 211-217 (2021). https://doi.org:10.1038/s41586-021-03472-9DOI
  22. [22]Wang, Y. et al. Van der Waals contacts between three-dimensional metals and two-dimensional semiconductors. Nature 568, 70-74 (2019). https://doi.org:10.1038/s41586-019-1052-3DOI
  23. [23]Li, W. et al. Approaching the quantum limit in two-dimensional semiconductor contacts. Nature 613, 274-279 (2023). https://doi.org:10.1038/s41586-022-05431-4DOI
  24. [24]English, C. D., Shine, G., Dorgan, V. E., Saraswat, K. C. & Pop, E. Improved Contacts to MoS2 Transistors by Ultra-High Vacuum Metal Deposition. Nano Letters 16, 3824-3830 (2016). https://doi.org:10.1021/acs.nanolett.6b01309DOI
  25. [25]Song, S. et al. Wafer-scale production of patterned transition metal ditelluride layers for two-dimensional metal–semiconductor contacts at the Schottky–Mott limit. Nature Electronics 3, 207-215 (2020). https://doi.org:10.1038/s41928-020-0396-xDOI
  26. [26]Kong, L. et al. Wafer-scale and universal van der Waals metal semiconductor contact. Nature Communications 14, 1014 (2023). https://doi.org:10.1038/s41467-023-36715-6
  27. [27]Liu, G. et al. Graphene-assisted metal transfer printing for wafer-scale integration of metal electrodes and two-dimensional materials. Nature Electronics 5, 275-280 (2022). https://doi.org:10.1038/s41928-022-00764-4DOI
  28. [28]Liu, Y. et al. Promises and prospects of two-dimensional transistors. Nature 591, 43-53 (2021). https://doi.org:10.1038/s41586-021-03339-zDOI
  29. [29]Andrews, K., Bowman, A., Rijal, U., Chen, P.-Y. & Zhou, Z. Improved Contacts and Device Performance in MoS2 Transistors Using a 2D Semiconductor Interlayer. ACS Nano 14, 6232-6241 (2020). https://doi.org:10.1021/acsnano.0c02303DOI
  30. [30]Tang, A. et al. Toward Low-Temperature Solid-Source Synthesis of Monolayer MoS2. ACS Applied Materials & Interfaces 13, 41866-41874 (2021). https://doi.org:10.1021/acsami.1c06812DOI
  31. [31]Zhang, Q. et al. Tunable Multi-Bit Nonvolatile Memory Based on Ferroelectric Field-Effect Transistors. Advanced Electronic Materials 8, 2101189 (2022). https://doi.org:https://doi.org/10.1002/aelm.202101189
  32. [32]Zhang, S. et al. Low Voltage Operating 2D MoS2 Ferroelectric Memory Transistor with Hf1-xZr xO2 Gate Structure. Nanoscale Research Letters 15, 157 (2020). https://doi.org:10.1186/s11671-020-03384-z
  33. [33]Xu, L. et al. Ferroelectric-Modulated MoS2 Field-Effect Transistors as Multilevel Nonvolatile Memory. ACS Applied Materials & Interfaces 12, 44902-44911 (2020). https://doi.org:10.1021/acsami.0c09951DOI
  34. [34]Liu, L. et al. Electrical characterization of MoS2 field-effect transistors with different dielectric polymer gate. AIP Advances 7, 065121 (2017). https://doi.org:10.1063/1.4991843DOI
  35. [35]Huang, K. et al. Hf₀.₅Zr₀.₅O₂ Ferroelectric Embedded Dual-Gate MoS₂ Field Effect Transistors for Memory Merged Logic Applications. IEEE Electron Device Letters 41, 1600-1603 (2020). https://doi.org:10.1109/LED.2020.3019681DOI
  36. [36]Yu, L. et al. Graphene/MoS₂ Hybrid Technology for Large-Scale Two-Dimensional Electronics. Nano Letters 14, 3055-3063 (2014). https://doi.org:10.1021/nl404795z
  37. [37]Chee, S.-S. et al. Lowering the Schottky Barrier Height by Graphene/Ag Electrodes for High-Mobility MoS₂ Field-Effect Transistors. Advanced Materials 31, 1804422 (2019). https://doi.org:https://doi.org/10.1002/adma.201804422
  38. [38]Gao, J. et al. Transition-Metal Substitution Doping in Synthetic Atomically Thin Semiconductors. Advanced Materials 28, 9735-9743 (2016). https://doi.org:https://doi.org/10.1002/adma.201601104
  39. [39]Mulaosmanovic, H., Breyer, E. T., Mikolajick, T. & Slesazeck, S. Ferroelectric FETs With 20-nm-Thick HfO₂ Layer for Large Memory Window and High Performance. IEEE Transactions on Electron Devices 66, 3828-3833 (2019). https://doi.org:10.1109/TED.2019.2930749DOI
  40. [40]McClellan, C. J., Yalon, E., Smithe, K. K. H., Suryavanshi, S. V. & Pop, E. High Current Density in Monolayer MoS₂ Doped by AlOx. ACS Nano 15, 1587-1596 (2021). https://doi.org:10.1021/acsnano.0c09078DOI
  41. [41]Cai, Z., Toprasertpong, K., Liu, Z., Takenaka, M. & Takagi, S. Understanding HZO Thickness Scaling in Si FeFETs: Low Operating Voltage, Fast Wake-Up, and Suppressed Charge Trapping. IEEE Transactions on Electron Devices, 1-7 (2024). https://doi.org:10.1109/TED.2024.3386508DOI
  42. [42]Liao, C. Y. et al. Multibit Ferroelectric FET Based on Nonidentical Double HfZrO₂ for High-Density Nonvolatile Memory. IEEE Electron Device Letters 42, 617-620 (2021). https://doi.org:10.1109/LED.2021.3060589DOI
  43. [43]Schulman, D. S., Arnold, A. J. & Das, S. Contact engineering for 2D materials and devices. Chemical Society Reviews 47, 3037-3058 (2018). https://doi.org:10.1039/C7CS00828GDOI
  44. [44]Kim, B.-K. et al. Origins of genuine Ohmic van der Waals contact between indium and MoS₂. npj 2D Materials and Applications 5, 9 (2021). https://doi.org:10.1038/s41699-020-00191-zDOI
  45. [45]Kalbitz, R., Gerhard, R. & Taylor, D. M. Fixed negative interface charges compromise organic ferroelectric field-effect transistors. Organic Electronics 13, 875-884 (2012). https://doi.org:https://doi.org/10.1016/j.orgel.2012.01.034
  46. [46]Dickens, B., Balizer, E., DeReggi, A. S. & Roth, S. C. Hysteresis measurements of remanent polarization and coercive field in polymers. Journal of Applied Physics 72, 4258-4264 (1992). https://doi.org:10.1063/1.352213DOI
  47. [47]Liao, P. J. et al. in 2021 Symposium on VLSI Technology. 1-2.
  48. [48]Hoffman, J. et al. Ferroelectric Field Effect Transistors for Memory Applications. Advanced Materials 22, 2957-2961 (2010). https://doi.org:https://doi.org/10.1002/adma.200904327
  49. [49]Ma, T. P. & Jin-Ping, H. Why is nonvolatile ferroelectric memory field-effect transistor still elusive? IEEE Electron Device Letters 23, 386-388 (2002). https://doi.org:10.1109/LED.2002.1015207DOI
  50. [50]Radisavljevic, B. & Kis, A. Mobility engineering and a metal–insulator transition in monolayer MoS2. Nature Materials 12, 815-820 (2013). https://doi.org:10.1038/nmat3687DOI
  51. [51]Chen, X. et al. Probing the electron states and metal-insulator transition mechanisms in molybdenum disulphide vertical heterostructures. Nature Communications 6, 6088 (2015). https://doi.org:10.1038/ncomms7088DOI
  52. [52]Baugher, B. W. H., Churchill, H. O. H., Yang, Y. & Jarillo-Herrero, P. Intrinsic Electronic Transport Properties of High-Quality Monolayer and Bilayer MoS2. Nano Letters 13, 4212-4216 (2013). https://doi.org:10.1021/nl401916sDOI
  53. [53]Jariwala, D. et al. Band-like transport in high mobility unencapsulated single-layer MoS2 transistors. Applied Physics Letters 102 (2013). https://doi.org:10.1063/1.4803920DOI

Paper details

vlnc:W_6rspuyr9
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents