Wrinkling instabilities in stiff films on compliant substrates are strongly affected by spatial fluctuations in film stiffness. We develop a homogenized instability theory for one-dimensional film–substrate systems with random bending stiffness. The heterogeneous stability equation is reformulated as a Lippmann–Schwinger equation for the curvature field, and a strong-contrast expansion is derived using a local–nonlocal kernel decomposition and a cavity-field formulation. Truncation at third order yields an effective polarizability and a Dyson-type dispersion relation for predicting the critical load and wavenumber. The stiffness is modeled as an exponentially mapped Gaussian random field, allowing the required two- and three-point connected statistics to be obtained analytically. The theory is validated against generalized eigenvalue calculations and Fourier spectral simulations. Increasing stiffness contrast lowers the critical load and shifts the instability toward higher wavenumbers, producing shorter wrinkles. At weak contrast, the threshold follows the universal scaling Nc(0)−Nc∼ε2, whereas at moderate and strong contrast the third-order approximation is more accurate than the second-order theory. Wavelength selection is controlled by the ratio of the dominant material wavelength λ∗ to the harmonic-mean reference wavelength λH. For λ∗/λH<1, the harmonic-mean model accurately predicts the wrinkle wavelength. The framework provides a mechanics-based tool for reliability assessment and design of statistically heterogeneous film–substrate systems.
Introduction
Film–substrate systems subjected to compression commonly exhibit wrinkling instabilities, producing periodic surface morphologies with characteristic wavelengths and amplitudes [1, 2, 3, 4, 5, 6]. The compressive stress may be generated by a mismatch in thermal expansion [7, 8, 9], swelling [10, 11, 12], or residual stresses introduced during fabrication [13, 14]. Wrinkling is widely observed in natural morphogenesis, including surface patterns in fruits and vegetables [15, 16], wrinkles in skin [17, 18, 19], and geological folding [20]. It has also been exploited in engineering applications such as tunable optics [21, 22, 23, 24, 25, 26], stretchable and flexible electronic devices [27, 28, 29, 30, 31, 32], and biomedical systems [33, 34, 35]. These applications require a quantitative understanding of the onset of instability, wavelength selection, mode competition, and post-buckling evolution.
The mechanics of spatially homogeneous film–substrate systems is now relatively well established. Early analyses identified the competition between film bending and substrate resistance as the basic mechanism governing erning the instability threshold [36]. Subsequent stability analyses related the critical load and wavelength to film thickness, elastic mismatch, substrate thickness, interfacial conditions, and loading state [1, 3]. Nonlinear energy minimization and asymptotic analyses further predicted wrinkle amplitudes and the competition among post-buckling modes [37, 38, 39, 40, 41, 42]. At larger compressive strains, wrinkles may undergo period doubling [43, 44, 45], folding [4, 46, 47, 48] and ridge [49, 50, 51]. Recent studies have extended the classical framework to dynamic loading [52, 53, 54, 55, 56], substrate viscoelasticity [57, 58, 59], prestretch [43, 60, 61] and multilayered architectures [62, 63, 64]. Spectral methods [65, 66], nonlinear finite-element simulations [47, 67, 68, 69, 70] and other numerical methods [71, 72, 73, 74] have also been developed to resolve large-domain pattern evolution and multiple post-buckling branches.
Practical film and substrate are rarely perfectly homogeneous. Most existing studies on heterogeneous systems focus on deterministic heterogeneity, including periodic or graded stiffness modulation [75, 76, 77, 78, 79, 80, 81], thickness gradients [82, 83, 84, 85, 86, 87, 88] and regularly arranged microstructures [89, 90, 91, 92, 93, 94]. In these systems, the spatial distribution of material properties is prescribed in advance, allowing the wrinkle morphology to be controlled through the location, geometry, or periodicity of the heterogeneity [95]. Manufacturing-induced variations, however, are generally irregular and cannot be represented by a single deterministic profile [96, 97]. Instead, spatial fluctuations in stiffness, thickness, or residual stress are more naturally modeled as random fields.
Stochastic homogenization and effective-medium theories provide a natural starting point for describing the macroscopic response of such random materials [98, 99, 100, 101, 102, 103, 104]. Classical variational bounds [105, 106, 107] and strong-contrast expansions [108, 109, 110, 111] relate effective material properties to statistical descriptors of the underlying microstructure, particularly two- and higher-order correlation functions. These approaches have been applied extensively to static effective properties, including conductivity, elasticity, and transport. More recently, for heterogeneous materials represented by continuous random fields, Zhong et al. [112] reformulated variable-coefficient governing equations as a Lippmann–Schwinger integral equation and introduced a cavity-field renormalization to improve the convergence of the associated Neumann expansion. For Gaussian random fields, the resulting corrections can be expressed in terms of low-order statistical descriptors, such as the covariance function. Wrinkling, however, differs fundamentally from static homogenization problems. It is a spectral instability problem in which the critical threshold is determined by the minimum of an effective dispersion relation. Random stiffness fluctuations introduce wavenumber coupling and modify not only the instability threshold but also the critical mode structure. Therefore, a direct application of standard homogenization formulas is not sufficient.
To address this issue, this work develops a strong-contrast homogenization framework for one-dimensional film–substrate systems with randomly heterogeneous bending stiffness. The substrate response is represented by a unified Fourier-domain kernel, which covers Winkler/liquid foundations and, after condensation of tangential–normal interfacial coupling, elastic half-space substrates. The heterogeneous stability problem is reformulated as a Lippmann–Schwinger equation for the curvature field. By introducing a local–nonlocal kernel decomposition and a cavity-field representation, we derive a strong-contrast expansion for the effective polarizability and obtain a Dyson-type effective dispersion relation for the critical load and critical wavenumber. For exponentially mapped Gaussian stiffness fields, the required two- and three-point connected statistics are derived in closed form. The theoretical predictions are validated against generalized eigenvalue calculations and Fourier spectral simulations, and the effects of stiffness contrast and material correlation length on the instability threshold, wavelength selection, and mode localization are systematically examined. The framework provides a predictive tool for assessing instability reliability and guiding structural design in heterogeneous thin-film systems.
The rest of this paper is organized to progressively connect the mechanics of heterogeneous wrinkling with a statistically informed homogenized instability criterion. § 2 formulates the one-dimensional film–substrate model, introduces the unified substrate-kernel representation, and summarizes the numerical eigenvalue and spectral methods used for validation. § 3 develops the Lippmann–Schwinger formulation, the strong-contrast expansion, and the homogenized instability criterion. § 4 specifies the exponentially mapped Gaussian random stiffness model and derives the closed-form two- and three-point connected statistics required by the SCE. § 5 compares the theory with numerical simulations and discusses how stiffness contrast and material correlation length affect the critical load, wavelength selection, spectral complexity, and spatial localization of the critical mode. Finally, the conclusions summarize the principal findings, clarify the physical implications of the proposed framework, and outline possible extensions.
Theoretical Model and Governing Equations
This section establishes the mechanical model used throughout the paper. We first define the one-dimensional film–substrate configuration, the random bending-stiffness field, and the basic assumptions adopted in the thin-film description. We then derive the governing equations for both Winkler-type and elastic half-space substrates and introduce a unified scalar substrate kernel that allows these cases to be treated within the same instability framework. Finally, the homogeneous benchmark and the numerical methods for heterogeneous systems are summarized, providing reference solutions for validating the strong-contrast theory developed in the following sections.
Problem Description and Basic Assumptions
Consider a hard film of length L and thickness h (h≪L) bonded to a soft substrate surface, as illustrated in Figure 1. The film is subjected to in-plane compression along the axial direction, i.e., x–direction, resulting in a deflection w(x) in the z direction. The film is assumed to be linearly elastic, with spatially varying Young’s modulus E(x) and constant Poisson’s ratio ν. Under the plane-strain approximation, the effective modulus and bending stiffness are
Figure 1. Schematic of the one-dimensional film–substrate system considered in this work. A stiff film of length L and thickness h is bonded to a compliant substrate and subjected to an in-plane compressive membrane force along the x direction. The out-of-plane deflection of the film is denoted by w(x) in the z direction. The film bending stiffness B(x)=Eˉ(x)h3/12 is spatially heterogeneous and treated as a random field, whereas the substrate is assumed to be homogeneous and represented by a linear normal reaction operator p=K[w], or equivalently by the Fourier-domain substrate kernel K^(q).
Eˉ(x)=1−ν2E(x),B(x)=12Eˉ(x)h3.(1)
The spatial variation of B(x) represents the random bending-stiffness heterogeneity considered in this work.
The substrate exerts a normal reaction force p(x) on the thin film, which is expressed as
p(x)=K[w](x),(2)
where K is the linear response operator of the substrate. We assume that the substrate is homogeneous in this work. Under periodic or infinite-domain conditions, K can be diagonalized in Fourier space, yielding a scalar relation between the Fourier transforms of the normal reaction force and the deflection:
p^(q)=K(q)w^(q),(3)
where K(q) denotes the substrate stiffness kernel, which generally depends on the wavenumber q. This unified formulation includes both the constant stiffness K(q)=K corresponding to the liquid/Winkler foundation approximation and the wavenumber-dependent stiffness K(q) for elastic half-spaces.
Governing Equations
A one-dimensional von Kármán nonlinear model is used to describe the response of the film mid-plane. u(x) denotes the in-plane axial displacement of the film mid-plane, while w(x) is the out-of-plane deflection. The total axial strain in the film is then given by
ϵ(x)=ϵ0(x)+dxdu+21(dxdw)2.(4)
For convenience we use ′ to denote derivative with respect to x.
The in-plane membrane force in the film N(x) and strain satisfy the linear elastic constitutive law:
N(x)=hEˉ(x)[ϵ0+u′+21(w′)2].(5)
The substrate exerts tangential and normal tractions T=(T1,T2) at the interface, where T1 is the shear stress and T2 is the normal stress, which are governed by the following equilibrium equations:
N′(x)=T1(x),(6)
(B(x)w′′)′+(Nw′)′+T2(x)=0.(7)
When the substrate is a liquid substrate or a Winkler-type foundation, the interface provides no tangential stress, and the normal stress is locally proportional to the deflection, i.e., T1≡0 and T2=Kw. Consequently, equation (7) reduces to a scalar governing equation in terms of w(x):
(B(x)w′′)′′+Nw′′+Kw=0.(8)
For cases in which shear tractions cannot be neglected, such as a solid substrate, we adopt the formulation for the surface response of an elastic half-space given in [65]. For an isotropic, linearly elastic solid half-space (with Young’s modulus Es and Poisson’s ratio νs, under the plane-strain and one-dimensional wrinkling assumption (k2=0), only the tangential displacement u(x) and normal displacement w(x) are retained. Let the Fourier domain wavenumber be q≡k1, and denote k=∣q∣. The interfacial stresses and displacements then satisfy the following relation:
Equation (9) reflects the tangential–normal coupling at the interface of a solid substrate: D12 and D21 are nonzero, implying that both T1 and T2 generally depend on u and w. Therefore, for the case of a solid half-space, equations (6)–(7) and (9) must be solved simultaneously as a coupled system for (u,w).
The strong-contrast expansion developed below is formulated for a scalar normal substrate kernel. For Winkler or liquid substrates, this scalar representation is exact, with K(q)≡K. For an elastic half-space, the coupled interfacial response is condensed at the linear instability level by eliminating the in-plane displacement. This condensation allows Winkler/liquid substrates and elastic half-space substrates to be treated within the same scalar dispersion formulation. The detailed derivation of Keff(q) is provided in Appendix § 10. The unified substrate kernel is written as
To start with, we briefly review the main results concerning homogeneous film–substrate system, i.e. the film has a constant bending stiffness (B(x)≡B). In this case, Eq. (8) reduces to the classical beam-on-Winkler-foundation equation:
Bw′′′′+Nw′′+Kw=0.(16)
For an infinitely long system, or a finite system with periodic boundary conditions, we seek a Fourier-mode solution w(x)=Aeiqx with A=0. Substitution into Eq. (16) gives the dispersion relation D0(q;N)=Bq4−Nq2+K=0, whose minimum is attained at qc2=N/(2B). Therefore, instability occurs when the minimum value of D0(q;N) becomes non-positive, yielding the classical results Nc=2BK, and qc=(K/B)1/4. These expressions provide the benchmark instability criterion for the homogeneous beam-on-Winkler-foundation system and will be used for comparison with the heterogeneous case.
Numerical Methods for Heterogeneous Systems
For heterogeneous systems, the instability threshold can no longer be obtained from a closed-form dispersion relation and must instead be determined numerically. In this subsection, we employ two complementary approaches: a generalized eigenvalue method to compute the critical load and mode, and a Fourier spectral iteration scheme to solve the coupled equilibrium equations for solid-substrate systems.
Generalized Eigenvalue Method
When the bending stiffness B(x) varies spatially, Eq. (8) becomes a fourth-order ordinary differential equation with variable coefficients, and the problem no longer admits a scalar dispersion relation in terms of a single wavenumber. The instability condition can instead be recast as the generalized eigenvalue problem
M[w]=NQ[w],(17)
with
M[w]=(B(x)w,xx),xx+K[w],Q[w]=−w,xx,(18)
and
References
[1]X. Chen, J. W. Hutchinson, Herringbone Buckling Patterns of Compressed Thin Films on Compliant Substrates, Journal of Applied Mechanics 71 (5) (2004) 597–603.DOI
[3]E. P. Chan, A. J. Crosby, Fabricating Microlens Arrays by Surface Wrinkling, Advanced Materials 18 (24) (2006) 3238–3242.DOI
[4]F. Brau, P. Damman, H. Diamant, T. A. Witten, Wrinkle to fold transition: Influence of the substrate response, Soft Matter 9 (34) (2013) 8177–8186.DOI
[5]Y. Zhao, B. Feng, J. Lee, N. Lu, D. M. Pierce, A multi-layered model of human skin elucidates mechanisms of wrinkling in the forehead, Journal of the Mechanical Behavior of Biomedical Materials 105 (2020) 103694.DOI
[7]N. Bowden, S. Brittain, A. G. Evans, J. W. Hutchinson, G. M. Whitesides, Spontaneous formation of ordered structures in thin films of metals supported on an elastomeric polymer, Nature 393 (6681) (1998) 146–149.DOI
[8]J. Song, H. Jiang, W. M. Choi, D. Y. Khang, Y. Huang, J. A. Rogers, An analytical study of two-dimensional buckling of thin films on compliant substrates, Journal of Applied Physics 103 (1) (2008) 014303.DOI
[9]M. Barnes, F. Feng, J. S. Biggins, Surface Instability in a Nematic Elastomer, Physical Review Letters 131 (23) (2023) 238101.arxiv.org/abs/2303.07215
[10]H. S. Kim, A. J. Crosby, Solvent-Responsive Surface via Wrinkling Instability, Advanced Materials 23 (36) (2011) 4188–4192.DOI
[11]H. Vandeparre, P. Damman, Wrinkling of Stim ulosresponsive Surfaces: Mechanical Instability Coupled to Diffusion, Physical Review Letters 101 (12) (2008) 124301.pubmed.ncbi.nlm.nih.gov/18851377
[12]S. S. Velankar, V. Lai, R. A. Vaia, Swelling-Induced Delamination Causes Folding of Surface-Tethered Polymer Gels, ACS Applied Materials & Interfaces 4 (1) (2012) 24–29.DOI
[13]A. Pundt, E. Nikitin, P. Pekarski, R. Kirchheim, Adhesion energy between metal films and polymers obtained by studying buckling induced by hydrogen, Acta Materialia 52 (6) (2004) 1579–1587.DOI
[14]S. Mukherjee, P. Saxena, Deformation and stability of initially stressed hyperelastic plates, International Journal of Solids and Structures 311 (2025) 113253.DOI
[15]J. Yin, Z. Cao, C. Li, I. Sheinman, X. Chen, Stress-driven buckling patterns in spheroidal core/shell structures, Proceedings of the National Academy of Sciences 105 (49) (2008) 19132–19135.DOI
[16]J. Yin, X. Chen, I. Sheinman, Anisotropic buckling patterns in spheroidal film/substrate systems and their implications in some natural and biological systems, Journal of the Mechanics and Physics of Solids 57 (9) (2009) 1470–1484.DOI
[17]E. Cerda, L. Mahadevan, Geometry and Physics of Wrinkling, Physical Review Letters 90 (7) (2003) 074302.pubmed.ncbi.nlm.nih.gov/12633231
[18]C. Dagdeviren, Y. Shi, P. Joe, R. Ghaffari, G. Balooch, K. Usgaonkar, O. Gur, P. L. Tran, J. R. Crosby, M. Meyer, Y. Su, R. Chad Webb, A. S. Tedesco, M. J. Slepian, Y. Huang, J. A. Rogers, Conformal piezoelectric systems for clinical and experimental characterization of soft tissue biomechanics, Nature Materials 14 (7) (2015) 728–736.DOI
[19]P. Chavoshnejad, A. H. Foroughi, N. Dhandapani, G. K. German, M. J. Razavi, Effect of collagen degradation on the mechanical behavior and wrinkling of skin, Physical Review E 104 (3) (2021) 034406.
[20]P. J. Hudleston, S. H. Treagus, Information from folds: A review, Journal of Structural Geology 32 (12) (2010) 2042–2071.DOI
[21]S. G. Lee, D. Y. Lee, H. S. Lim, D. H. Lee, S. Lee, K. Cho, Switchable Transparency and Wetting of Elastomeric Smart Windows, Advanced Materials 22 (44) (2010) 5013–5017.DOI
[22]Z. B. Wang, M. G. Helander, J. Qiu, D. P. Puzzo, M. T. Greiner, Z. M. Hudson, S. Wang, Z. W. Liu, Z. H. Lu, Unlocking the full potential of organic light-emitting diodes on flexible plastic, Nature Photonics 5 (12) (2011) 753–757.DOI
[23]I. Jung, J. Xiao, V. Malyarchuk, C. Lu, M. Li, Z. Liu, J. Yoon, Y. Huang, J. A. Rogers, Dynamically tunable hemispherical electronic eye camera system with adjustable zoom capability, Proceedings of the National Academy of Sciences 108 (5) (2011) 1788–1793.DOI
[24]Z. Shen, L. Wu, S. Zhu, Y. Zheng, X. Chen, Random lasing action in a polydimethylsiloxane wrinkle induced disordered structure, Applied Physics Letters 105 (2) (2014) 021106.DOI
[25]K. Wu, Y. Sun, H. Yuan, J. Zhang, G. Liu, J. Sun, Harnessing Dynamic Wrinkling Surfaces for Smart Displays, Nano Letters 20 (6) (2020) 4129–4135.DOI
[26]C. Chen, C. A. Airoldi, C. A. Lugo, R. K. Bay, B. J. Glover, A. J. Crosby, Flower Inspiration: Broad-Angle Structural Color through Tunable Hierarchical Wrinkles in Thin Film Multilayers, Advanced Functional Materials 31 (5) (2021) 2006256.DOI
[27]D.-Y. Khang, H. Jiang, Y. Huang, J. A. Rogers, A Stretchable Form of Single-Crystal Silicon for High-Performance Electronics on Rubber Substrates, Science 311 (5758) (2006) 208–212.pubmed.ncbi.nlm.nih.gov/16357225
[28]B. Xu, D. Chen, R. C. Hayward, Mechanically Gated Electrical Switches by Creasing of Patterned Metal/Elastomer Bilayer Films, Advanced Materials 26 (25) (2014) 4381–4385.DOI
[29]L. Wang, C.-L. Pai, M. C. Boyce, G. C. Rutledge, Wrinkled surface topographies of electrospun polymer fibers, Applied Physics Letters 94 (15) (2009) 151916.DOI
[30]W. Wu, Stretchable electronics: Functional materials, fabrication strategies and applications, Science and Technology of Advanced Materials 20 (1) (2019) 187–224.DOI
[31]K. Xie, A. Glasser, S. Shinde, Z. Zhang, J.-M. Rampnoux, A. Maali, E. Clouet, G. Hadziioannou, H. Kellay, Delamination and Wrinkling of Flexible Conductive Polymer Thin Films, Advanced Functional Materials 31 (21) (2021) 2009039.DOI
[32]Y. Chen, T. Wang, Y. Cui, Y. Lun, J. Hong, Effect of flexoelectricity on buckle-delamination of nanofilms adhered to compliant substrates, International Journal of Solids and Structures 312 (2025) 113276.DOI
[33]D. Wu, B. Guo, Y. Yin, S. Zuo, H. Lei, Z. Zhao, D. Fang, Instability of vascular bilayer reveals the protective role of connective tissue, Journal of the Mechanics and Physics of Solids 208 (2026) 106466.
[34]V. Lumelsky, M. Shur, S. Wagner, Sensitive skin, IEEE Sensors Journal 1 (1) (2001) 41–51.
[35]A. Nathan, B. Park, A. Sazonov, S. Tao, I. Chan, P. Servati, K. Karim, T. Charania, D. Striakhilev, Q. Ma, R. Murthy, Amorphous silicon detector and thin film transistor technology for large-area imaging of X-rays, Microelectronics Journal 31 (11-12) (2000) 883–891.
[36]M. A. Biot, Bending of an infinite beam on an elastic foundation, Journal of Applied Mechanics 4 (1) (2021) A1–A7.
[37]B. Audoly, A. Boudaoud, Buckling of a stiff film bound to a compliant substrate—Part I;, Journal of the Mechanics and Physics of Solids 56 (7) (2008) 2401–2421.DOI
[38]B. Audoly, A. Boudaoud, Buckling of a stiff film bound to a compliant substrate—Part II;, Journal of the Mechanics and Physics of Solids 56 (7) (2008) 2422–2443.DOI
[39]B. Audoly, A. Boudaoud, Buckling of a stiff film bound to a compliant substrate—Part III;, Journal of the Mechanics and Physics of Solids 56 (7) (2008) 2444–2458.DOI
[40]S. Cai, D. Breid, A. Crosby, Z. Suo, J. Hutchinson, Periodic patterns and energy states of buckled films on compliant substrates, Journal of the Mechanics and Physics of Solids 59 (5) (2011) 1094–1114.DOI
[41]A. Kordolemis, A. E. Giannakopoulos, Wrinkling analysis of a stiff shallow film mounted on a cylindrically curved compliant substrate, Part II: Checkerboard and hexagonal modes, International Journal of Solids and Structures 317 (2025) 113383.DOI
[42]X. Ren, X. Li, Z. Du, X. Guo, A novel approach to stress minimization of post-buckled membranes, International Journal of Mechanical Sciences 310 (2026) 111130.DOI
[43]Y. Zhao, Y. Cao, W. Hong, M. K. Wadee, X.-Q. Feng, Towards a quantitative understanding of period-doubling wrinkling patterns occurring in film/substrate bilayer systems, Proceedings of the Royal Society A: Mathematical, Physical and Engineering Sciences 471 (2173) (2015) 20140695.pubmed.ncbi.nlm.nih.gov/25568620
[44]S. K. Saha, Geometric Prepatterning-Based Tuning of the Period Doubling Onset Strain During Thin-Film Wrinkling, Journal of Applied Mechanics 84 (5) (2017) 051010.DOI
[45]C. Yu, K. O’Brien, Y.-H. Zhang, H. Yu, H. Jiang, Tunable optical gratings based on buckled nanoscale thin films on transparent elastomeric substrates, Applied Physics Letters 96 (4) (2010) 041111.DOI
[46]R. Zhao, X. Zhao, Multimodal Surface Instabilities in Curved Film–Substrate Structures, Journal of Applied Mechanics 84 (8) (2017) 081001.DOI
[47]S. Nikravesh, Y.-L. Shen, Wrinkle, fold, and ridge patterns of thin films attached to a compliant substrate: Direct numerical simulations involving plastic yielding, Thin-Walled Structures 198 (2024) 111649.DOI
[48]S. Nagashima, R. Ota, R. Okamoto, S. Matsubara, D. Okumura, Elastocapillary folding in film–substrate bilayers, International Journal of Mechanical Sciences 315 (2026) 111455.DOI
[49]J. Zang, X. Zhao, Y. Cao, J. W. Hutchinson, Localized ridge wrinkling of stiff films on compliant substrates, Journal of the Mechanics and Physics of Solids 60 (7) (2012) 1265–1279.DOI
[50]L. Jin, A. Takei, J. W. Hutchinson, Mechanics of wrinkle/ridge transitions in thin film/substrate systems, Journal of the Mechanics and Physics of Solids 81 (2015) 22–40.DOI
[51]X. Guan, A. P. Sarma, E. Kakarla Hamesh, J. Yang, N. Nguyen, E. Cerda, L. Pocivavsek, S. S. Velankar, Compression-induced buckling of thin films bonded to viscous substrates: Uniform wrinkles vs localized ridges, International Journal of Solids and Structures 254–255 (2022) 111843.DOI
[52]F. Box, D. O’Kiely, O. Kodio, M. Inizan, A. A. Castrejón-Pita, D. Vella, Dynamics of wrinkling in ultrathin elastic sheets, Proceedings of the National Academy of Sciences 116 (42) (2019) 20875–20880.DOI
[53]M. Abi Ghanem, X. Liang, B. Lydon, L. Potocsnak, T. Wehr, M. Ghanem, S. Hoang, S. Cai, N. Boechler, Wrinkles Riding Waves in Soft Layered Materials, Advanced Materials Interfaces 6 (1) (2019) 1801609.arxiv.org/abs/1810.06624
[54]B. MacNider, X. Liang, S. Hoang, M. A. Ghanem, S. Cai, N. Boechler, Dynamic compression of soft layered materials yields tunable and spatiotemporally evolving surface patterns, Physical Review E 107 (3) (2023) 035002.DOI
[55]J.-F. Zhou, K.-M. Hu, H.-Y. Lin, Z.-Q. Dong, T.-Y. Zhao, X.-X. Li, G. Meng, W.-M. Zhang, Dynamic Wrinkling Instability of Elastic Films on Viscoelastic Substrates, Journal of Applied Mechanics 91 (081011) (2024).DOI
[56]F. Simões, A. Pinto Da Costa, Dynamics of a beam on a displacement-driven nonlocal foundation under a moving load, International Journal of Solids and Structures 330 (2026) 113877.DOI
[57]S.-J. Yu, Y.-P. Du, Y.-D. Sun, Q.-L. Ye, H. Zhou, Wrinkling patterns in metal films sputter deposited on viscoelastic substrates, Thin Solid Films 638 (2017) 230–235.DOI
[58]X. Liu, Y. Liu, Radial instabilities of viscoelastic thin film-elastic substrate system triggered by local pre-stretch: A theoretical solution, Mechanics of Materials 143 (2020) 103315.DOI
[59]X. Liu, Y. Liu, X.-Q. Feng, Radial wrinkling of viscoelastic film-substrate systems, International Journal of Solids and Structures 249 (2022) 111689.DOI
[60]A. Auguste, L. Jin, Z. Suo, R. C. Hayward, The role of substrate pre-stretch in post-wrinkling bifurcations, Soft Matter 10 (34) (2014) 6520–6529.DOI
[61]X. Qiu, J. Guo, C. Wang, H. Tan, Stretch-induced wrinkling and post-buckling bifurcation in rectangular films: Insights into energy barrier mechanisms, International Journal of Mechanical Sciences 299 (2025) 110398.DOI
[62]A. D. Bakiler, A. Javili, Wrinkling of a compressible trilayer domain under large plane deformations, International Journal of Solids and Structures 241 (2022) 111465.DOI
[63]B. Wang, H. Chen, H. Bi, B. Zhang, S. Cao, J. Zhou, H. Ouyang, The roles of the viscoelastic layer on controlling evolution of wrinkles in a tri-layer structure with finite thickness, Applied Mathematical Modelling 141 (2025) 115910.DOI
[64]H. Kwak, J. Lee, J. Kim, H. Jo, K. Ki, A. Lee, Wrinkling of thin films in pre-stretched soft substrate trilayers, International Journal of Mechanical Sciences 312 (2026) 111213.DOI
[65]Z. Huang, W. Hong, Z. Suo, Nonlinear analyses of wrinkles in a film bonded to a compliant substrate, Journal of the Mechanics and Physics of Solids 53 (9) (2005) 2101–2118.DOI
[66]S.-F. Yin, B. Li, Y.-P. Cao, X.-Q. Feng, Surface wrinkling of anisotropic films bonded on a compliant substrate, International Journal of Solids and Structures 141–142 (2018) 219–231.DOI
[67]Z.-C. Shao, Y. Zhao, W. Zhang, Y. Cao, X.-Q. Feng, Curvature induced hierarchical wrinkling patterns in soft bilayers, Soft Matter 12 (38) (2016) 7977–7982.pubmed.ncbi.nlm.nih.gov/27714339
[68]H. Miyoshi, S. Matsubara, D. Okumura, Bifurcation and deformation during the evolution of periodic patterns on a gel film bonded to a soft substrate, Journal of the Mechanics and Physics of Solids 148 (2021) 104272.
[69]S. Kikuchi, S. Matsubara, S. Nagashima, D. Okumura, Diversity of the bifurcations and deformations on films bonded to soft substrates: Robustness of the herringbone pattern and its cognate patterns, Journal of the Mechanics and Physics of Solids 159 (2022) 104757.DOI
[70]S. Abu-Salih, Electromechanical buckling of periodic patterns on stiff film bonded to a compliant substrate – Analytical and numerical postbuckling analyses, Journal of the Mechanics and Physics of Solids 197 (2025) 106062.
[71]J. Shen, Y. Fu, A. Pirrera, R. M. Groh, Wrinkling of differentially growing bilayers with similar film and substrate moduli, Journal of the Mechanics and Physics of Solids 193 (2024) 105900.arxiv.org/abs/2405.11989
[72]Y. Yang, S. Zhao, Z. Dai, F. Xu, Programmable wrinkling patterns of liquid crystal network bilayers on compliant substrates, International Journal of Solids and Structures 309 (2025) 113206.DOI
[73]F. Xu, A nonlinear toroidal shell model for surface morphologies and morphogenesis, JMPS (2025).DOI
[74]J. Guo, C. Wang, Path tracking of buckling instability in flexible structures, International Journal of Mechanical Sciences 310 (2026) 111073.DOI
[75]J. W. Yang, G. H. Nie, Analysis of Sinusoidal Interfacial Wrinkling of an Anisotropic Film Sandwiched Between Two Compliant Layers, Journal of Applied Mechanics 81 (9) (2014) 091013.DOI
[76]J. Wang, B. Li, Y.-P. Cao, X.-Q. Feng, H. Gao, Wrinkling micropatterns regulated by a hard skin layer with a periodic stiffness distribution on a soft material, Applied Physics Letters 108 (2) (2016) 021903.DOI
[77]B. Wang, C. Xu, B. Zhang, H. Bi, S. Cao, Y. Huang, First-order and second-order wrinkling of thin elastic film laminated on a graded substrate, International Journal of Mechanical Sciences 243 (2023) 108047.DOI
[78]Z. Xue, C. Wang, H. Tan, Articulated surface wrinkling of a patterned film with periodic stiffness distribution on a compliant substrate, International Journal of Solids and Structures 200–201 (2020) 132–144.DOI
[79]Y. Fu, Y.-S. Wang, Y. Fu, Wrinkling of a film/substrate bilayer with periodic material properties: An assessment of the Winkler foundation model, International Journal of Non-Linear Mechanics 166 (2024) 104815.DOI
[80]M. Shen, X. Wu, S. Mao, Wrinkling of heterogeneous thin films over liquid substrate, Acta Mechanica (2025).
[81]R. Zhao, Y. Yan, K. Yu, Y. Liu, Nonlinear thermal vibration of variable stiffness composite laminated plates, International Journal of Mechanical Sciences 318 (2026) 111527.DOI
[82]A. B. Croll, A. J. Crosby, Pattern Driven Stress Localization in Thin Diblock Copolymer Films, Macromolecules 45 (9) (2012) 4001–4006.DOI
[83]Y. Li, J. J. Peterson, S. B. Jhaveri, K. R. Carter, Patterned Polymer Films via Reactive Silane Infusion-Induced Wrinkling, Langmuir 29 (14) (2013) 4632–4639.DOI
[84]S. Yu, Y. Ni, L. He, Q.-L. Ye, Tunable Formation of Ordered Wrinkles in Metal Films with Controlled Thickness Gradients Deposited on Soft Elastic Substrates, ACS Applied Materials & Interfaces 7 (9) (2015) 5160–5167.DOI
[85]J.-W. Wang, B. Li, Y.-P. Cao, X.-Q. Feng, Surface Wrinkling Patterns of Film–Substrate Systems With a Structured Interface, Journal of Applied Mechanics 82 (051009) (2015).DOI
[86]S. Yu, L. Ma, Y. Sun, C. Lu, H. Zhou, Y. Ni, Controlled Wrinkling Patterns in Periodic Thickness-Gradient Films on Polydimethylsiloxane Substrates, Langmuir 35 (22) (2019) 7146–7154.DOI
[87]S. Yu, Y. Guo, H. Li, C. Lu, H. Zhou, L. Li, Tailoring Ordered Wrinkle Arrays for Tunable Surface Performances by Template-Modulated Gradient Films, ACS Applied Materials & Interfaces 14 (9) (2022) 11989–11998.DOI
[88]Y. Wang, K. Wang, B. Wang, Peeling behavior of a discontinuously adhered film/substrate system within finite deflection, International Journal of Solids and Structures 309 (2025) 113207.DOI
[89]K. Efimenko, M. Rackaitis, E. Manias, A. Vaziri, L. Mahadevan, J. Genzer, Nested self-similar wrinkling patterns in skins, Nature Materials 4 (4) (2005) 293–297.pubmed.ncbi.nlm.nih.gov/15750598
[90]J.-H. Lee, H. W. Ro, R. Huang, P. Lemaïtre, T. A. Germer, C. L. Soles, C. M. Stafford, Anisotropic, Hierarchical Surface Patterns via Surface Wrinkling of Nanopatterned Polymer Films, Nano Letters 12 (11) (2012) 5995–5999.DOI
[91]D. Yan, K. Zhang, G. Hu, Wrinkling of structured thin films via contrasted materials, Soft Matter 12 (17) (2016) 3937–3942.DOI
[92]S. Nagashima, K. Suzuki, S. Matsubara, D. Okumura, Bio-Inspired Instability-Induced Hierarchical Patterns Having Tunable Anisotropic Wetting Properties, Advanced Materials Interfaces 10 (14) (2023) 2300039.DOI
[93]P. Sun, J. Huang, J. Zhang, F. Meng, Wrinkling suppression in thin film using position distribution of microstructures, International Journal of Mechanics and Materials in Design 20 (1) (2024) 3–13.DOI
[94]Y. Zhang, F. Wang, Y. Ma, X. Feng, Buckling configurations of stiff thin films tuned by micro-patterns on soft substrate, International Journal of Solids and Structures 161 (2019) 55–63.DOI
[95]W. Zhou, R. Hewson, M. Santer, Optimizing membrane–substrate buckling to control surface deformation pattern, International Journal of Solids and Structures 331 (2026) 113898.DOI
[96]Z. Baizhikova, J.-L. Le, R. Ballarini, Stochastic Buckling of Geometrically Imperfect Beams on Elastic Foundation, Journal of Applied Mechanics 90 (011003) (2022).DOI
[97]R.-C. Liu, Y. Liu, A. Goriely, Surface wrinkling of a film coated to a graded substrate, Journal of the Mechanics and Physics of Solids 186 (2024) 105603.arxiv.org/abs/2312.10162
[98]X. Li, Z. Liu, S. Cui, C. Luo, C. Li, Z. Zhuang, Predicting the effective mechanical property of heterogeneous materials by image based modeling and deep learning, Computer Methods in Applied Mechanics and Engineering 347 (2019) 735–753.DOI
[99]R. V. Roy, Analytical representation and efficient computation of the effective conductivity of two-phase composite materials, International Journal for Numerical Methods in Engineering 123 (15) (2022) 3567–3593.DOI
[100]D. Dhar, A. Jain, Beyond effective stiffness: A modified differential Mori-Tanaka-Voigt homogenization for predicting stresses in individual inclusions, International Journal of Solids and Structures 309 (2025) 113152.DOI
[101]R. Xue, W. Chen, Q. Yuan, X. Huang, Hyperelastic inclusions in a linear elastic and isotropic material matrix, International Journal of Mechanical Sciences 315 (2026) 111389.DOI
[102]R. Zhang, B. Li, T. Rabczuk, X. Fu, X. Zhuang, Second-order homogenization of flexoelectric composites for piezoelectric behavior, International Journal of Mechanical Sciences 317 (2026) 111494.DOI
[103]X. Shi, M. Chen, J. Zhang, J. Shao, Representative volume element size for elastic modulus of random composites, International Journal of Mechanical Sciences 321 (2026) 111659.DOI
[104]B. H. Nguyen, M. Schneider, Symmetries in stochastic homogenization and adjustments for the RVE method, International Journal of Solids and Structures 325 (2026) 113728.DOI
[105]Z. Hashin, S. Shtrikman, A variational approach to the theory of the elastic behaviour of multiphase materials, Journal of the Mechanics and Physics of Solids 11 (2) (1963) 127–140.DOI
[106]M. Beran, Use of the vibrational approach to determine bounds for the effective permittivity in random media, Il Nuovo Cimento (1955-1965) 38 (2) (1965) 771–782.DOI
[107]G. W. Milton, Bounds on the complex permittivity of a two-component composite material, Journal of Applied Physics 52 (8) (1981) 5286–5293.DOI
[108]S. Torquato, Effective electrical conductivity of two-phase disordered composite media, Journal of Applied Physics 58 (10) (1985) 3790–3797.
[109]D. C. Pham, S. Torquato, Strong-contrast expansions and approximations for the effective conductivity of isotropic multiphase composites, Journal of Applied Physics 94 (10) (2003) 6591–6602.
[110]D. Chen, S. Torquato, Designing disordered hyperuniform two-phase materials with novel physical properties, Acta Materialia 142 (2018) 152–161.DOI
[111]M. Skolnick, S. Torquato, Accurate formula for the effective conductivity of highly clustered two-phase materials, Physical Review Materials 9 (5) (2025) 055601.
[112]L. Zhong, S. Mao, Contrast expansion formalism and rapidly convergent approximations for transport properties of heterogeneous materials characterized by continuous random fields, Physical Review B 112 (13) (2025) 134207.DOI
Jerry Lin, Zeyuan Hu, Tom Beucler, Katherine Frields, Hannah Christensen, Walter Hannah, Helge Heuer, Peter Ukkonnen, Laura A. Mansfield, Tian Zheng et al. ·