betaFeedback

WorksPhysics and Astronomy

Cryogenic hyperabrupt strontium titanate varactors for sensitive reflectometry of quantum dots

Abstract

Radio frequency reflectometry techniques enable high bandwidth readout of semiconductor quantum dots. Careful impedance matching of the resonant circuit is required to achieve high sensitivity, which however proves challenging at cryogenic temperatures. Gallium arsenide-based voltage-tunable capacitors, so-called varactor diodes, can be used for in-situ tuning of the circuit impedance but deteriorate and fail at temperatures below 10 K and in magnetic fields. Here, we investigate a varactor based on strontium titanate with hyperabrupt capacitance-voltage characteristic, that is, a capacitance tunability similar to the best gallium arsenide-based devices. The varactor design introduced here is compact, scalable and easy to wirebond with an accessible capacitance range from 45 pF to 3.2 pF. We tune a resonant inductor-capacitor circuit to perfect impedance matching and observe robust, temperature and field independent matching down to 11 mK and up to 2 T in-plane field. Finally, we perform gate-dispersive charge sensing on a germanium/silicon core/shell nanowire hole double quantum dot, paving the way towards gate-based single-shot spin readout. Our results bring small, magnetic field-resilient, highly tunable varactors to mK temperatures, expanding the toolbox of cryo-radio frequency applications.

Introduction

Recent years have seen rapid progress in the realization of spin qubits in semiconductors [1, 2, 3, 4]. Hole spins in germanium (Ge) and silicon (Si) nanostructures are of particular interest thanks to the availability of all-electrical spin control [2, 5, 6, 7, 8, 9], short gate times [10, 11, 12], high-temperature qubit operation [13, 14, 15], intrinsically low concentration of spinful nuclei and reduced hyperfine interaction due to the p-type hole wavefunction [16] and the presence of noise sweet spots [17, 18, 19].

Fast readout of charge and spin states in semiconductor qubit devices is typically achieved using high-frequency reflectometry methods such as radio frequency (RF)-single-electron transistors [20, 21, 22, 23], single lead sensor dots [24, 25] or gate-dispersive charge sensing [26, 27, 29, 30] [28]. The latter constitutes the smallest footprint charge sensing setup: The same gate that electrostatically defines a quantum dot is used to sense nearby dots. This makes gate-reflectometry the obvious choice to use with nanowire-qubits since external charge sensors are difficult to implement [31, 32, 33, 34, 35].

High device impedances, typically on the order of the resistance quantum Z≥25.8 kΩZ \geq25.8\,\mathrm{k\Omega} up to Z∼GΩZ \sim\mathrm{G\Omega} for gate-sensors make it necessary to downconvert towards

Z0=50 ΩZ_0 = 50\,\Omega for maximizing signal and bandwidth. Down-conversion is implemented using inductor-capacitor (LC) resonators, so-called tank circuits, consisting of surface-mount inductors and parasitic circuit or device capacitances [29]. Careful circuit design ensures optimal signal-to-noise ratios (SNRs) and high sensitivities [27, 36]. The RF characteristics of the circuits are frequently affected by cryogenic temperatures and magnetic fields required for qubit operations. Thus, in-situ tuning of the impedance matching and thereby the coupling of the RF source circuitry and the LC resonator is needed. This can be achieved using varactors [16, 24, 37, 38, 39].

Commercial varactors with high tuning range and steep capacitance-voltage (CV)-curves, classified as hyperabrupt varactors, are typically doped gallium arsenide (GaAs) diodes. The width of the diode’s p-n junction depletion region can be tuned by applying a reverse bias voltage, effectively changing the capacitor thickness and thus the diode’s series capacitance. Doped varactors are suitable for quantum applications only to a limited extent, requiring multiple diodes [38, 39]. This is due to freezing-out effects [39] and strong dependencies on applied magnetic fields. In particular, perfect impedance matching using GaAs varactors was so far only demonstrated down to T∼200 mKT \sim200\,\mathrm{mK}, using two varactors [39].

To resolve these issues, quantum paraelectric materials such as strontium titanate (STO) are under consideration as alternative cryogenic varactors [40, 41]. Below 10 K, the dielectric constant of STO ranges from ϵr=10 000−24 000\epsilon_r = 10\,000 - 24\,000 depending on the crystal orientation and was shown to be tunable with electric fields, reaching more than a factor of 10 lower dielectric constants [42, 43, 44, 45]. This strong electric field tunability makes STO a prime candidate for the design of tunable cryogenic RF components, such as varactors or resonators [40, 41, 46]. The relatively small target capacitance range Cvar<50C_{\mathrm{var}} < 50 pF [38] required for impedance matching makes STO varactor engineering challenging. Given the high εr\varepsilon_r, a plate capacitor formed by electrodes on opposite faces of STO crystals encounters conflicting constraints when required to reach such low CvarC_{\mathrm{var}}: i) either the capacitor plate size is too small for wirebonding or ii) the plate-to-plate distance is too large to form uniformly high fields, reducing the tunability [41]. Furthermore, contacting the electrodes on opposing faces of the crystal is inconvenient and limits scalability.

Here, we present a surface-patterned ring varactor design on STO which achieves hyperabrupt CV characteristics and a tuning range exceeding that of typical GaAs varactors [24, 38, 39] while operating down to mK temperatures and independent of magnetic fields. We fabricate varactors of various dimensions and characterize them first at 4 K, optimizing for tunability and capacitance range.

Next, we integrate such a varactor in a tank circuit for gate-dispersive readout. The selected design has a 300 μm footprint, smaller than STO plate-capacitor layouts and packaged commercial varactor diodes. Critical coupling is reached over a broad range of temperatures from T≈4T \approx4 K to 11 mK and in magnetic fields up to 2 T without retuning of the varactor. We use the matched circuit to dispersively measure charge transitions in a hole double quantum dot (DQD) formed in a Ge/Si core/shell nanowire (NW) [47, 48, 49, 50]. Similar NWs were used to demonstrate all-electrical, ultrafast spin qubit operation with a high degree of tunability [6, 7, 8, 10]. To directly probe the significance of impedance matching for gate-dispersive charge sensing, we measure signal-to-noise ratios (SNRs) for variable matching conditions and at different charge transitions. Our implementation of gate-dispersive charge sensing paves the way for high-fidelity gate-dispersive single-shot spin readout with gated quantum dots (QDs). The realization of a highly tunable capacitor at cryogenic temperatures enables more sophisticated circuit architectures in various applications beyond charge sensing in semiconductors.

Varactor Characterization at 4 K

Geometry

The varactor ring design is presented in Figure 1 a). It features two electrodes, a central circle with diameter DD and a concentric ring, 50 μm wide and separated from the circle by a distance ww. A gap g=20g = 20 μm wide in the outer ring facilitates lift-off. The electrodes were patterned on the polished side of a commercially available (001) STO chiplet with thickness t=0.5t = 0.5 mm (Appendix A1). This geometry provides several key features for optimal varactor performance: electric fields in the crystal are localized and large close to the electrodes. This allows for high tunability of εr\varepsilon_r while keeping the peak capacitance Cmax⁡C_{\max} in the desired range. The small varactor footprint of ∼300\sim300 μm and single-sided metallization allows tight integration with other circuit components and provides scalability. In particular, we are able to fit 9 independent ring varactors on a chiplet the size of commercial surface-mount GaAs varactors used in comparable experiments (MACOM MA46-series) [24, 38, 39].

Figure 1. Geometry of STO ring varactors a) Schematic diagram of the STO varactor design. Two gold electrodes, a circle with diameter DD and a concentric ring with a spacing to the circle ww and gap g=20g = 20 μm form the capacitor. Application of a DC voltage VvarV_{\mathrm{var}} induces an electric field within the STO crystal which is highly localized due to the compact geometry. Inset: Optical micrograph of finished varactors. b) Zero-field capacitance Cmax⁡C_{\max} as a function of DD for w=60w = 60 μm, simulated in COMSOL (triangles) and measured (circles).

All measurements presented in this section were performed at 4 K using standard lock-in techniques at 1 kHz. No frequency dependence of tunability and εr\varepsilon_r from 1 kHz to 50 MHz reported previously, predicting constant εr\varepsilon_r up to 100 GHz [44]. We thus expect our low-frequency results to apply at typical reflectometry frequencies as well. We estimate the zero-field capacitance Cmax⁡C_{\max} of our design using COMSOL to find optimum device dimensions. For simplicity, we assume an isotropic dielectric constant εr=24’000\varepsilon_r = 24’000, approximately the experimental value for field lines parallel to the (001) direction at 4 K [44]. In our simulation, we primarily focus on DD and ww, finding that neither gg nor the width of the outer ring have a strong influence on Cmax⁡C_{\max}. We vary DD from 60 μm to 160 μm and ww from 10 μm to 80 μm and fabricate an array of 36 different combinations, excluding w>60w > 60 μm due to decreased tunability. Not all combinations were measured because too small ww and DD frequently resulted in shorts between the two electrodes from wirebonding (see Appendix C1 for details).

In Figure 1 b), we compare the zero-field capacitance Cmax⁡C_{\max} estimated from finite-element simulations and measurements for w=60w = 60 μm and variable DD. We find good agreement, noting that some small capacitance over-estimations by the model could be explained by the anisotropy of εr\varepsilon_r, which was neglected in the simulation. Furthermore, the partial loss of tunability caused by the application of negative varactor voltages VvarV_{var} described in II B and Figure 2 c) may also explain some of the measured CmaxC_{max} lying below the model, as some of these values were taken from voltage sweeps starting at a varactor voltage Vvar=−2V_{var}=-2 V.

Figure 2. CV-Characteristic a) Varactor capacitance CvarC_{var} as a function of applied DC voltage measured on 13 nominally identical devices (light green), mean value (dark green) and fit of the mean to equation (1) (dark blue). Fitting all 13 traces yields C0=34±3C_0=34\pm3 pF, Voffset=−0.8±0.1V_{offset}=-0.8\pm0.1 V and V0=2.4±0.3V_0=2.4\pm0.3 V. b) Comparison of the capacitance-tunability of a commercial GaAs varactor with one exemplary STO ring at 4 K. The yellow (turquoise) dashed lines are fits of equation (2) to the steepest regime of the STO (GaAs) CV-traces, indicated by the shaded areas. c) Schematic image (left panel) and quantitative analysis (right panel) of the varactor peak capacitance reduction. Applying negative VvarV_{var} (purple diamonds) causes a significant degradation of Cvar(Vvar=0C_{var}(V_{var}=0 V) which is less severe for positive VvarV_{var} (red circles).

Voltage-Tunability

The capacitance-tunability of STO varactors relies on an incipient ferroelectric phase transition at low temperatures which is never reached due to quantum fluctuations [40, 41, 46, 51]. Below about 10 K, the low temperature limit is reached and ϵ\epsilon has no further temperature dependence, thus rendering STO varactors highly reliable and repeatable below 10 K. Johnson’s relation describes the resulting highly nonlinear dependence of ϵr\epsilon_r on DC electric fields to first order and neglecting anisotropies and can be used to express the voltage-tunability of CvarC_{var} as [40, 41, 51]:

Cvar(Vvar)=C0(1+(Vvar−Voffset)2V02)1/3(1)C_{var}(V_{var})=\frac{C_0}{\left(1+\frac{(V_{var}-V_{offset})^2}{V_0^2}\right)^{1/3}} \tag*{(1)}

Here, C0C_0 is the zero-field capacitance, VvarV_{var} the applied varactor voltage and VoffsetV_{offset} accounts for an experimentally observed deviation of the peak capacitance from Vvar=0V_{var}=0 V. The voltage V0V_0 parametrizes the strength of the tunability of ϵr\epsilon_r and is geometry-dependent [46].

From now on, we focus on devices with with D=100 μmD=100\,\mu\mathrm{m} and w=50 μmw=50\,\mu\mathrm{m} as these varactors covered the desired capacitance range and could be easily bonded. CV-characteristics of 13 nominally identical devices are shown in Figure 2 a) together with their average trace, indicating that all devices have capacitances within 10% of the average. All curves show the characteristic maximum capacitance around zero VvarV_{var} and the suppression at larger voltages. Fitting all 13 traces to equation (1) reveals that the model agrees very well with the data over almost the entire range. Further, the three fit parameters are very similar for all devices, exhibiting a variability of only about 10%.

For comparison with other varactors, we use the standard diode-varactor theory, which uses a power law exponent γ\gamma as a benchmark for varactor performance, where a larger γ\gamma indicates higher tunability. Abrupt varactors have γ≤0.5\gamma\leq0.5 and if γ>0.5\gamma>0.5 the varactor is considered hyperabrupt, indicating highest tunability [52]. As a standard for comparison, a typical GaAs varactor used in similar experiments has γ=1\gamma=1 (Figure 2 b)) The CV-characteristic of a diode varactor near its peak tunability regime can be expressed as:

Cvar(Vvar)=K(Vvar+Φdiode)γ(2)C_{var}(V_{var})=\frac{K}{(V_{var}+\Phi_{diode})^\gamma} \tag*{(2)}

where KK is the capacitance constant, VvarV_{var} is the applied varactor voltage, Φdiode\Phi_{diode} is the built-in potential of the

varactor [52]. For GaAs varactors, ΦGaAs=1.3\Phi_{GaAs}=1.3 V holds [53].

Fitting the peak tunability regime of the CV traces of all 13 devices to equation (2), we find hyperabrupt behavior over a large voltage range with mean γ‾STO=0.72±0.05\overline{\gamma}_{STO}=0.72\pm0.05 as shown in Appendix C3. This is slightly higher than γ≈0.66\gamma\approx0.66 expected from (1). We note that in this high-tunability regime (yellow shaded in Figure 2 b)), the fit to equation (2) captures the measured capacitance slightly better than equation (1) as shown in Appendix C2. In analogy to the built-in potential, VoffsetV_{offset} is used as ΦSTO=0.8\Phi_{STO}=0.8 V in the fits. To minimize the loss in tunability discussed in the following, we measure a single varactor from Vvar=0V_{var}=0 V to Vvar=100V_{var}=100 V as shown in Figure 2 b). The accessible capacitance range of the STO varactor is Cvar=45.0C_{var}=45.0 pF to 3.2 pF, exceeding the range of a commercial GaAs device used in comparable experiments (MACOM MA46H204-1056) [24, 38, 39] and of previous STO plate-capacitor implementations [41].

Interestingly, varactors with identical geometry but fabricated on (100) and (111) STO showed no significantly different CV-response as compared to the (001) devices. While (100) is equivalent to the (001) direction, the zero-field dielectric constant of (111) STO is ϵr=12 000\epsilon_r = 12\,000 [44], half the value of (001) STO. The approximately circular symmetry of the surface-electrode evenly integrates over all field directions in the crystal plane, effectively averaging away the anisotropy in ϵr\epsilon_r.

Sweeping from Vvar=0V_{\mathrm{var}} = 0 V to a finite voltage ΔVvar\Delta V_{\mathrm{var}} and back to zero, we observe a reduction in Cvar(Vvar=0 V)C_{\mathrm{var}}(V_{\mathrm{var}} = 0\ \mathrm{V}) from C0C_0 to CreturnC_{\mathrm{return}} (Figure 2 c)). If VvarV_{\mathrm{var}} is subsequently kept within this same range, the CV-characteristic remains stable. The reduction is strongly dependent on the sign of ΔVvar\Delta V_{\mathrm{var}} as defined in Figure 1 a). Negative ΔVvar\Delta V_{\mathrm{var}} cause significantly bigger losses than positive ΔVvar\Delta V_{\mathrm{var}}. This effect is quantified in the right panel of Figure 2 c), where Creturn/C0C_{\mathrm{return}}/C_0 is measured by sweeping to increasingly large ∣ΔVvar∣|\Delta V_{\mathrm{var}}| and back to zero. The lost tunability range is fully recovered upon thermal cycling to 295 K. Similar effects have been previously discussed with several paraelectric materials and can be explained by the polarization of microclusters in the crystal such as O-vacancies in STO [46, 51]. This voltage polarity- and voltage history-dependent CV characteristic, while not related to ferroelectric hysteresis, has been referred to as hysteresis in the literature [41, 46]. The residual degradation of tunability present even when only applying positive voltages can easily be circumvented by choosing appropriate varactor dimensions and limiting the range of voltages applied.

Gate-Dispersive Charge Sensing with Ge/Si core/shell Nanowire Double Quantum Dots

Impedance Matching

In a next step, we implement gate-dispersive charge sensing with a Ge/Si core/shell NW hole DQD, using a STO varactor to optimize impedance matching. See Appendix A 2 for NW device fabrication details. Quantum dots hosted in these NWs have been measured in direct current (DC) measurements [48, 49, 54, 55, 56, 57], using additional quantum dots as charge sensors [31, 32] and with an on-chip superconducting resonator [35, 58]. A strong, electrically tunable direct Rashba spin-orbit interaction (SOI) is present in Ge/Si core/shell NWs [6, 7, 8, 49], enabling all-electrical spin control. Recent spin qubit experiments in this system have shown Rabi frequencies of several hundreds of MHz [10].

The reflectometry setup used to integrate an STO ring varactor with the NW device shown in Figure 3 a) is described in more detail in Appendix B. The tank resonance frequency at fres=316.20±0.05f_{\mathrm{res}} = 316.20 \pm0.05 MHz allows us to extract the parasitic capacitance Cp=1.15±0.03C_p = 1.15 \pm0.03 pF of the circuit. Tuning the tank as shown in Figure 3 b), we reach impedance matching at probe temperature Tprobe≈15T_{\mathrm{probe}} \approx15 mK in a Bluefors dilution refrigerator. We find the STO varactor to be highly temperature-resilient (Appendix C4).

Figure 3. Reflectometry setup and Impedance Matching a) Gate-reflectometry circuit with STO matching-varactor. The false-colored SEM image shows a NW device with nine gates, five of which were used to form a DQD with two plungers (green) and three barrier gates (blue). The NW (red) is contacted on either side, enabling DC-current measurements through the wire. b) Impedance matching at probe temperature Tprobe≈15T_{\mathrm{probe}} \approx15 mK. At perfect matching, the reflected amplitude is minimal and the phase response indicates a sudden shift from undercoupled (Vvar<6.625V_{\mathrm{var}} < 6.625 V) to overcoupled (Vvar>6.625V_{\mathrm{var}} > 6.625 V). c) Magnetic field-dependent impedance matching at T≈1.5T \approx1.5 K without NW device. The tank with a STO ring varactor is unaffected by magnetic fields up to 2 T. Using a GaAs varactor, the matching voltage shifts strongly, complicating qubit measurements. d) Coupling coefficient β\beta as a function of VvarV_{\mathrm{var}}.

The resonator coupling coefficient β=Q0Qext\beta= \frac{Q_0}{Q_{\mathrm{ext}}} depicted in Figure 3 d) is a convenient measure to evaluate the matching of the resonator impedance ZresZ_{\mathrm{res}} to the external source circuitry impedance Z0Z_0 and can be extracted from the S21S_{21} response of the tank at resonance following Ibberson et al. [39]. It is formally defined as the ratio of the unloaded (Q0Q_0) and external (QextQ_{\mathrm{ext}}) quality factors [39]. The transition from the under- (β<1\beta< 1; Zres>Z0Z_{\mathrm{res}} > Z_0) to the overcoupled regime (β>1\beta> 1; Zres<Z0Z_{\mathrm{res}} < Z_0) is marked by a narrow minimum in the reflected amplitude ∣S21∣|S_{21}| and a sudden flip by 180° in the phase offset signal Φ\Phi where perfect matching (β=1\beta= 1; Zres=Z0Z_{\mathrm{res}} = Z_0) is reached.

The impact of an in-plane magnetic field on the matching with STO ring varactors and commercial GaAs varactors is compared in Figure 3 c). Both scans were recorded at 1.5 K because the GaAs varactor froze out at lower temperatures. No NW device was present for both scans. Fixing fprobef_{\mathrm{probe}} near resonance at zero field, BB is subsequently swept against VvarV_{\mathrm{var}}. The GaAs varactor shows a strong dependence on BB even for B≤1B \leq1 T, the typical spin qubit operation range [2, 3, 5, 8, 13]. The STO remains independent of B-field down to mK temperatures (Appendix C5).

Charge Sensing

Finally, we investigate charge transitions in a Ge/Si core/shell NW DQD using the impedance-matched tank circuit. Five bottom gates were used to define a DQD (Figure 3 a)). Bias triangles, the hallmark signature of a DQD, are shown in Figure 4 a). Due to Coulomb blockade, source-drain current ISDI_{SD} can only flow through the DQD if at least one quantized energy level of each dot lies within the bias window. Estimating the plunger gate lever arms from the DC bias triangle yields αP1≈0.3\alpha_{P1} \approx0.3 and αP2≈0.24\alpha_{P2} \approx0.24 for the gates P1P1 and P2P2, respectively, in line with previous results on bottom-gated devices [48].

Figure 4. Sensing a Ge/Si NW DQD a) Charge stability map of a DQD formed in the Ge/Si core/shell NW, showing a characteristic bias triangle in the DC-current measurement (top). The simultaneously acquired reflectometry data (middle & bottom) feature an interdot line coinciding with the triangle baseline and lead transitions of the right dot with its reservoir. Orange arrows indicate the faintly visible excited state transition parallel to the baseline and purple arrows point to the baseline of the lower triangle. b) Time-domain SNR measurements of similar transitions as in a) as a function of VvarV_{\mathrm{var}} and integration time tintt_{\mathrm{int}}. Both transition SNRs behave similarly: The highest SNR regime is shifted to higher VvarV_{\mathrm{var}} from the perfect matching (yellow shaded region). Investigating the interdot line, longer integration times are required to cross the SNR = 1 threshold (pink). Five independent SNR measurements were taken for each VvarV_{\mathrm{var}}. Error bars represent one standard deviation. c) The SNR can be increased by applying higher powers up to approximately Pprobe=−58P_{\mathrm{probe}} = -58 dBm where the signal saturates. d) Demodulated data measured on (dark blue) and off (light blue) the lead transition at Pprobe=−60P_{\mathrm{probe}} = -60 dBm, corresponding to the empty circles in c).

Gate-reflectometry allows for the measurement of tunneling between the dots (interdot transition) as well as between the dot under the sensor gate and a neighbouring reservoir (lead transition). Simultaneously measuring ISDI_{SD} and changes of the reflected RF amplitude Δ∣S21∣\Delta|S_{21}| and phase ΔΦ\Delta\Phi demonstrates the correspondence of the two signals. In the reflectometry signal, the two reservoir transitions (white in ΔΦ\Delta\Phi) and the interdot transition (dark purple in ΔΦ\Delta\Phi) are clearly visible, appearing similarly in both Δ∣S21∣\Delta|S_{21}| and ΔΦ\Delta\Phi signals. Note that the phase jumps by more than ∣ΔΦ∣=10∘|\Delta\Phi| = 10^\circ at the transitions due to the close to perfect matching. In addition, the excited state appears faintly between the reservoir lines in parallel to the interdot transition (orange arrows), and a weak ground state transition of the lower triangle (purple arrows). The visibility of such features depends intricately on the balance of the tunnel barriers and the resulting tunnel rates in comparison to the resonator frequency. We note the remarkable stability of the quantum dots which can be formed in these NWs, manifesting in very sharp and highly repeatable transitions (see also Appendix § 4.2), only sporadically interrupted by a random charge switcher. A large-scale charge stability map is presented in Appendix § 4.2 alongside investigations into the tunability of interdot tunneling using the barrier gate B2B2.

For the following analysis of lineshapes and SNRs, we measure at zero source-drain bias to reduce random charge switchers and maximize dispersive signal. We select a lead transition which shows up primarily in the reflected phase and a bright interdot transition near the triangle depicted in Figure 4 a). The lead transition lineshape can either be dominated by the reservoir hole temperature THT_H, exhibiting a cosh⁡−2\cosh^{-2}-dependence on the gate voltage, or by tunnel-broadening which results in a Lorentzian lineshape with a tunnel rate γL\gamma_L [59]. Fitting the particular transition depicted in Appendix E1, we find slightly better agreement of the tail region with a cosh⁡−2\cosh^{-2}-relation, hinting towards the temperature broadened regime, i.e. that kBTH>ℏγLk_B T_H > \hbar\gamma_L with kBk_B Boltzmann’s constant and ℏ\hbar the reduced Planck’s constant. We can thus extract TH≈520±20T_H \approx520 \pm20 mK. This temperature is far above the refrigerator temperature, presumably due to microwave irradiation from the cryogenic amplifier. The interdot tunnel coupling tc≈22±5 μeVt_c \approx22 \pm5\,\mu\mathrm{eV} can be extracted fitting the interdot transition shown in Appendix E2. See Appendix E for estimates of the quantum capacitances associated with these transitions [59]. Power broadening sets in above Pprobe≈−60 dBmP_{\mathrm{probe}} \approx-60\,\mathrm{dBm} for both transitions mentioned, resulting in a reduced signal amplitude and larger width.

We investigate the impact of impedance matching through time-domain SNR measurements [28] at the two transitions mentioned above. Note that a random charge switcher occurred before we started the SNR measurements, resulting in a lower signal for the interdot transition than in the lineshape-investigation. We record time-traces of the demodulated reflectometry signal on and off a given charge transition for 2 s2\,\mathrm{s} with a lock-in time constant TC=4 μsTC = 4\,\mu\mathrm{s}. The in-phase (IS21I_{S_{21}}) and quadrature (QS21Q_{S_{21}}) components are then binned for a variable integration time tintt_{\mathrm{int}}. Figure 4 d) depicts the two signals on the IQIQ-plane for different tintt_{\mathrm{int}}. Comparing the distance of the two signals with the spread of the points estimates the SNR [28].

Figure 4 b) shows the SNRs measured as a function of VvarV_{\mathrm{var}}. The need for longer integration at the interdot transition may be due to different tunnel rates. Both transitions exhibit the same qualitative dependence of SNR on VvarV_{\mathrm{var}}. The best SNR is in the slightly overcoupled regime at Vvar≈7 VV_{\mathrm{var}} \approx7\,\mathrm{V} where β=1.28\beta= 1.28. In the case of dispersive sensing of a reactive load, the reduction of CvarC_{\mathrm{var}} by increasing VvarV_{\mathrm{var}} may lead to a higher tank quality factor, thus shifting the optimal sensing configuration away from perfect impedance matching [39]. The observed shift of the tank resonance to higher frequencies in 3 b) supports this hypothesis. Evidently, the ability to tune impedance matching is of major importance for SNR optimization. Detuning the varactor by ΔVvar=2 V\Delta V_{\mathrm{var}} = 2\,\mathrm{V} from the best operation point, causing a capacitance change of ΔCvar=±4 pF\Delta C_{\mathrm{var}} = \pm4\,\mathrm{pF}, the SNR drops by up to a factor of ∼2\sim2.

The power-dependence of the SNR at the lead transition for Vvar=7 VV_{\mathrm{var}} = 7\,\mathrm{V} is shown in 4 c). We find that Pprobe>−60 dBmP_{\mathrm{probe}} > -60\,\mathrm{dBm} causes significant instability of the system, as seen from the higher errors and plateauing of SNR, consistent with the onset of power broadening of the charge transitions (Appendix E). At Pprobe=−60 dBmP_{\mathrm{probe}} = -60\,\mathrm{dBm}, tint=41 μst_{\mathrm{int}} = 41\,\mu\mathrm{s} suffices to achieve SNR =1.1= 1.1 (see Appendix D3 for charge stability maps at low TCTC).

Conclusion and Outlook

In conclusion, we have fabricated and characterized hyperabrupt STO varactors with more than one order of magnitude tuning range. These varactors are not affected by moderate magnetic fields and can operate down to low mK temperatures. The small size allows tight integration with other PCB components and scaling in apapplications with multiple tunable capacitors such as multiplexed readout. We demonstrate the high-frequency functionality of these varactors for gate-dispersive sensing of a Ge/Si core/shell NW hole DQD. Other charge-sensing schemes such as the RF-single-electron transistors or single-lead sensor dots should equally benefit from optimized impedance matching.

These results open the possibility for gate-dispersive single shot readout of spins in Ge/Si core/shell NWs and spin-relaxation measurements. Increasing the sensor gate lever arm as well as the resonator quality factor are important steps to improve the signal further. Expanding the varactor design, more elaborate matching networks including two tunable capacitors in one device may allow for greater flexibility and voltage-tunability of the tank resonance frequency. In particular, lowering Cmax⁡C_{\max} while keeping γ\gamma similar should enable impedance matching with high-Q superconducting inductors.

As a circuit element for the nascent field of cryogenic RF engineering, the hyperabrubt varactors can be used in a multitude of applications akin to their room-temperature diode counterparts. Such applications include voltage-controlled oscillators and frequency multipliers, essential components in scaled quantum computation architectures where cryogenic signal generation and manipulation will be necessary to overcome the wiring bottleneck [60]. More immediately, the STO varactors may be used in the ever-growing number of solid state systems where RF reflectometry techniques at cryogenic temperatures and in magnetic fields are employed such as hybrid devices featuring superconducting components, for fast thermometry or in materials science [29].

Acknowledgments

We thank A. Tarasccio for his support during fabrication of the STO varactors. Furthermore, we acknowledge T. Berger for help with tank circuit modelling. We appreciated fruitful discussions with M. Hogg as well as his feedback on the manuscript. We thank G. Salis, E. Kelly and R. J. Warburton for useful discussions. Furthermore, we acknowledge S. Martin and M. Steinacher for technical support. This work was partially supported by the Swiss Nanoscience Institute (SNI), the NCCR SPIN, the Georg H. Endress Foundation, Swiss NSF (grant no. 179024), the EU H2020 European Microkelvin Platform EMP (grant no. 824109) and FET TOPSQUAD (grant no. 862046).

Data availability

The data supporting the plots of this paper are available at the Zenodo repository at https://doi.org/10.5281/zenodo.7818326.

Author Contributions

R.S.E, T.P. and D.M.Z conceived of the project and planned the experiments. R.S.E. and D.T. fabricated and measured the STO varactors with inputs from T.P.. S.S. fabricated, tuned and operated the NW device. M.J.C. and P.C.K. helped with the NW device fabrication. R.S.E and S.S. integrated the varactor with the NW device and implemented the charge sensing experiments with inputs from T. P.. R.S.E, S.S., D.T. and T.P. analyzed the data with inputs from M.J.C., S.G., A.V.K. and D.M.Z.. A.L. grew the NWs under the supervision of E.P.A.M.B.. R.S.E. wrote the manuscript with inputs from all authors. D.M.Z. supervised the project.

Competing Interests

The authors declare no competing interests.

Device Fabrication

Varactor fabrication

The STO ring varactors were optically defined using a Heidelberg μ\muPG laser-writer to pattern the structures on a commercially available SrTiO3_3 (001) wafer (refractive index n=2.39n = 2.39) [41]. The STO chiplets used were 0.5 mm thick, single-side polished, with a TiO2_2 termination on the back side, purchased from SurfaceNet. A bilayer of photoresist, consisting of LOR 3A and S1805, was used. The laser-writer was operated in pneumatic focusing mode due to the optical transparency at the wavelength of 405 nm. The structures were metallized with 5 nm/65 nm of Ti/Au. On one 10 × 10 mm2^2 chip, approximately 200 devices were co-fabricated and cleaved into smaller segments with 5 − 15 varactors for wirebonding and PCB integration.

Nanowire device fabrication

The QD device featured a set of 9 bottom gates with a width of 20 nm and a pitch of 50 nm. The gates were fabricated by electron beam lithography (EBL) on an intrinsic Si (100) chip with 290 nm of thermal SiO2_2. Upon cold development [61] the gates were metallized with 1 nm/9 nm of Ti/Pd, respectively. In order to electrically

insulate the gates from the NW, the gates were covered by a ∼ 20 nm thick layer of HfO2_2 grown by atomic layer deposition. A single Ge/Si core/shell NW with core radius of ∼ 10 nm and a shell thickness of ∼ 2.5 nm [47] was deterministically placed approximately perpendicular to the 9 bottom gates. However, the exact in-plane angle is unknown. Finally, ohmic contacts were patterned by EBL and metallized with 0.3 nm/50 nm of Ti/Pd after a 10 s dip in buffered hydrofluoric acid to remove the native SiO2_2. The scanning electron micrograph presented in Figure 3 shows a co-fabricated device.

Reflectometry setup

A STO varactor with D=100 μmD = 100\,\mu\mathrm{m} and w=50 μmw = 50\,\mu\mathrm{m} was integrated into a standard reflectometry setup shown in Figure 3 a) on a printed circuit board (PCB). Attenuated coaxial cables were used to inject an RF tone at frequency fprobef_\mathrm{probe} via a directional coupler (Mini-Circuits ZX30-17-5-S+) on the mixing chamber stage into a bias tee on the PCB (CD=87 pFC_D = 87\,\mathrm{pF}, RD=5 kΩR_D = 5\,\mathrm{k}\Omega). The varactor was operated as a tunable shunt-capacitor. A surface mount ceramic core inductor L=220±6 nHL = 220 \pm6\,\mathrm{nH}, in series with the parasitic capacitance of a bottom gate of the NW device formed the tank circuit. From the resonance frequency fres=316.20±0.05 MHzf_\mathrm{res} = 316.20 \pm0.05\,\mathrm{MHz} we find a parasitic capacitance Cp=1.15±0.03 pFC_p = 1.15 \pm0.03\,\mathrm{pF}. Filtered DC lines were used to provide gate-, source-drain bias- and varactor voltages. The reflected signal was amplified at the 4 K stage (Low Noise Factory LNC0.2-3A) and at room temperature (B&Z BZY-00100700). A Zurich Instruments UHFLI Lockin amplifier was used for signal generation and demodulation at room temperature. DC voltages were provided by a Basel Precision Instruments SP927 digital to analog converter and ISDI_{SD} was amplified by a Basel Precision Instruments SP983c current to voltage converter and recorded using an Agilent 34410A digital multimeter.

Varactor properties

Geometry

The results of COMSOL simulations of the CvarC_\mathrm{var}-dependence on DD and ww are shown in Table I.

D\wD \backslash w (μ\mum)1020304050607080
604336343231313030
806252484543424240
1007968615856545352
1209786757268666563
140117102918581797775
1601351201069994928986

Table I. TABLE I. Simulated CvarC_\mathrm{var} at Vvar=0V_\mathrm{var} = 0 V in pF

Corresponding measurements at T=4T = 4 K are shown in Table II. Note that only devices with w≤60 μmw \le60\,\mu\mathrm{m} were fabricated and for small ww and DD, measurements were often impossible because wirebonding created shorts between the two electrodes. Typical room-temperature capacitances were ≤1\le1 pF to 1.51.5 pF. In a few cases, the room-temperature capacitance was exceeding 1010 pF, likely originating from the DC wiring. These offsets were subtracted from the measured 44 K data presented here. Note that two such cases were excluded from the variability analysis in the main paper. The devices used for the variability analysis were fabricated only after the results presented in Tables II and III were analysed. In order to remove the potential for systematic variations of the varactor geometry due to small variations in the fabrication parameters, the CV traces recorded for Tables II and III were excluded from the variability analysis. The instances where two nominally identical devices show widely different capacitances at Vvar=0V_{\mathrm{var}} = 0 V may be due to device damage from lift-off or wirebonding.

D\wD\backslash w (μ\mum)102030405060
80----3641
100-79,4352-4346
12045----55,61
140--69-7874
160-88,83804674,2773,97

Table II. Measured CvarC_{\mathrm{var}} at Vvar=0V_{\mathrm{var}} = 0 V in pF

To assess the tunability range, we present the measured values of CvarC_{\mathrm{var}} at Vvar=30V_{\mathrm{var}} = 30 V in Table III.

D\wD\backslash w (μ\mum)102030405060
80----1312
100-24,1819-1415
12020----21,21
140--25-2325
160-26,72281518,1329,26

Table III. Measured CvarC_{\mathrm{var}} at Vvar=30V_{\mathrm{var}} = 30 V in pF

The limitations with regards to wirebonding should be easily overcome by adapting the electrode design to include remote, designated bondpads. This would make the smaller capacitance values listed in Table III accessible without severe reduction of tunability. Furthermore Cvar∼1C_{\mathrm{var}} \sim1 pF at Vvar=0V_{\mathrm{var}} = 0 V may be reached if the dimensions of the ring are further reduced which would allow for different tank topologies and [36] and tuning of the impedance matching with superconducting inductors.

Fitting of the high-tunability range

The two functions (1) and (2) can be used to fit the experimental CV trace. As shown in Figure 5, the agreement

Figure 5. Fitting the high-tunability regime: Both fit functions show good agreement with the experimental data but the power-law from equation (1) with γ=0.74\gamma= 0.74 captures the relevant slope slightly better than Johnson’s relation (2).

in the high-tunability regime is better for the power-law (2).

Variability of hyperabrupticity

All 13 devices depicted in main text Figure 2 a) show hyperabrupt CV-characteristics, as demonstrated in the fits shown in Figure 6. From these fits we find the mean power-law exponent to be γ‾=0.72±0.05\overline{\gamma} = 0.72 \pm0.05.

Figure 6. Fits of CV-traces for all 13 devices from main Fig. 2 a)

Temperature-dependence of matching

Figure 7 shows the tank resonance recorded in the Bluefors setup for a fixed VvarV_{\mathrm{var}} using an STO varactor and, for comparison, using a GaAs varactor diode (MACOM MA46H204-1056)[36, 38]. The STO varactor has almost no temperature-dependence below 4.3 K down to 11 mK. We have verified this robustness to temperature in multiple subsequent thermal cycles. No difference in varactor behavior was observed when tuning the varactor at K temperatures and subsequently cooling the refrigerator to mK versus keeping the varactor grounded while cooling to base temperature and tuning it later. The GaAs varactor in contrast shows a strong dependence on the temperature which sets in around 53 K, making perfect matching impossible in the mK regime.

Figure 7. Temperature-dependence of the tank resonance: Two subsequent cooldowns of the sample PCB without NW device in the Bluefors setup with a) an STO ring varactor and b) a commercial GaAs varactor used to tune impedance matching.

Zero-field anomaly

In the Bluefors LD setup, we observe a shift of the optimal matching condition within a range of B≈±50B \approx\pm50 mT from B=0B = 0 T as shown in Figure 8.

Figure 8. Zero-field anomaly: a) Shift of the tank resonance near zero field while VvarV_{\mathrm{var}} is kept constant. b) The effect is visible much more prominent in a scan at constant fprobef_{\mathrm{probe}}, sweeping VvarV_{\mathrm{var}}. The right panel is a zoom-in on the low-field regime. Note the apparent discontinuities at B<10B < 10 mT.

The origin of this shift remains elusive. Scans where VvarV_{\mathrm{var}} is ramped rather than fprobef_{\mathrm{probe}} show a stronger effect. The measurements presented in Figure 3 show only a minor feature at B=0B = 0 T. There are three apparent reasons for this discrepancy:

First, it is possible that the STO varactor tunability/dielectric constant is affected in a different manner at T≈15T \approx15 mK as compared to T≈1.5T \approx1.5 K. Since no such dependence was mentioned in previous work [41], this appears to be a less likely explanation.

Second, the cryogenic amplifiers used in the two setups were different, namely a Cosmic Microwave CLTF2 was used in the measurements at 1.5 K (similar as CLTF1 used in [41]), but the setup at 15 mK featured a Low Noise Factory LNC0.2-3A amplifier.

Third, the wirebonds used to bond the varactor are aluminium, whose normal-superconducting transition might show up around these fields. Further experiments are needed to finally exclude or confirm either hypothesis.

Charge sensing

Charge-stability maps

In Figure 9 we present a larger scale charge-stability map of the Ge/Si core/shell nanowire DQD. We note that these data were taken at the same barrier gate voltages as the bias triangles presented in the main text. The DC-current signal shown in Figure 9 a) exhibits multiple bias triangles, corresponding to transport in a double quantum dot (DQD). Towards the upper right quadrant of the graph, there is a region with signatures typical for a triple quantum dot (TQD) system, where the electrochemical potential of the center quantum dot is aligned with that of one of its adjacent outer quantum dots [62]. The presence of both types of transport signatures in this configuration is an indicator for cotunneling involving the center quantum dot, as was previously observed in similar Ge/Si core/shell nanowire devices [48].

Figure 9. Dispersive charge sensing over an extended plunger gate voltage range: a) DC-current measurement of the charge stability diagram in the investigated Ge/Si core/shell nanowire device. b) Reflected phase ΔΦ\Delta\Phi and c) RF amplitude Δ∣S21∣\Delta|S_{21}| measured along with the DC data in a). Here, we used a comparably large RF power Pprobe=−35P_\mathrm{probe}=-35 dBm, leading to significant power-broadening of the lead and interdot transitions and reducing the scan resolution requirements.

To make the lead and interdot transition lines more visible in the reflected signal, we increase the RF power to Pprobe=−35P_{\mathrm{probe}} = -35 dBm, which significantly broadens the transitions in the scan. In this specific charge stability diagram, we observe strong lead transitions at the regions where the DC transport signatures are those of a DQD, whereas the interdot transitions are more pronounced in the TQD region, indicating a change in the sensed quantum dot tunnel rates.

Tuning the interdot tunnel rate

The strength of the charge sensing signal is dependent on the tunnel rates of the sensed charge transition. To illustrate this, we show series of charge stability maps in Figure 10, tracking a particular interdot transition at VSD=0V_{SD}=0 mV for different center barrier gate voltages VB2V_{B2}. As the voltage applied to the center gate is reduced, the measured interdot transition becomes more faint, until it fully vanishes at VB2=1.79V_{B2}=1.79 V. The reduction in barrier voltage exponentially lowers the tunnel barrier, increasing the tunnel rate out of the sensitivity-window of our sensor [26].

Figure 10. Dependence on the center barrier gate voltage VB2V_{B2}. The strength of the reflected phase response ΔΦ\Delta\Phi at the interdot line strongly changes within tens of mV applied to VB2V_{B2}.

Reducing the lockin TC

In Figure 4 of the main text, we have determined the SNR for the lead and interdot transition of a selected bias triangle as a function of the integration time tintt_\mathrm{int}. We plot the closeup of an interdot transition and adjacent lead transitions at varying TCTC in Figure 11 to illustrate the possible measurement speedup. As TCTC is decreased, the background noise increases, such that at TC=1.33TC=1.33 μ\mus the transitions are barely visible anymore.

Figure 11. Dependence on the integration time. Interdot and lead transitions of a selected bias triangle, shown for varying TCTC. The signal can be recognized down to TC=1.33 μTC=1.33\,\mus.

Charge-transition lineshape

Investigating the lineshape and linewidth of charge transitions, we can extract several quantum dot parameters. In the case of primarily dispersive signals, i.e. the transition manifests predominantly as a phase shift ΔΦ\Delta\Phi, we can model the signal as a capacitive correction to CpC_p, the quantum capacitance CqC_q. The dispersive shift ΔΦ\Delta\Phi is translated to a change in circuit capacitance using the known slope δΦδf\frac{\delta\Phi}{\delta f} of Φ(fprobe)\Phi(f_\mathrm{probe}) at resonance for a given VvarV_\mathrm{var} and the well-known frequency-relation for a resonant tank circuit [59]:

fres=12πLC(3)f_\mathrm{res}=\frac{1}{2\pi\sqrt{LC}} \tag*{(3)}

where fresf_\mathrm{res} is the tank resonance frequency, LL the inductance and CC the capacitance of the resonator. The capacitive correction CqC_q is then:

Cq=(2πLΔΦ⋅δΦδf+1C)−2−C(4)C_q=\left(2\pi\sqrt{L}\Delta\Phi\cdot\frac{\delta\Phi}{\delta f}+\frac{1}{\sqrt{C}}\right)^{-2}-C \tag*{(4)}

In the following, we present the results of lineshape investigations of the lead transition and the interdot transition used also for the SNR analysis in the main text.

Lead transition

Fitting the lead transition lineshape recorded at Vvar=7 VV_{\mathrm{var}}=7\,\mathrm{V}, we find temperature-broadening to be dominant, kBTH>ℏγLk_BT_H>\hbar\gamma_L, where kBk_B denotes Boltzmann’s constant, THT_H the hole temperature of the lead, ℏ\hbar the reduced Planck’s constant and γL\gamma_L the lead-dot tunnel rate [59]. We fit the phase signal to:

ΔΦ=ΔΦmax⁡⋅cosh⁡−2(αP1(VP1−VP10)2kBTH)(5)\Delta\Phi=\Delta\Phi_{\max}\cdot\cosh^{-2}\left(\frac{\alpha_{P1}(V_{P1}-V_{P10})}{2k_BT_H}\right) \tag*{(5)}

Here, ΔΦmax⁡\Delta\Phi_{\max} is the amplitude of the phase response and VP10V_{P10} the center of the peak along the VP1V_{P1} axis [59]. The dependence of THT_H and ΔΦmax⁡\Delta\Phi_{\max} on the applied RF power PprobeP_{\mathrm{probe}} shown in Figure 12 indicates power-broadening to set in above Pprobe=−60 dBmP_{\mathrm{probe}}=-60\,\mathrm{dBm}. In the regime of flat THT_H, we find TH≈520±20 mKT_H\approx520\pm20\,\mathrm{mK} and Cq,L=266±8 aFC_{q,L}=266\pm8\,\mathrm{aF}.

Fitting the lead transition lineshape

Figure 12. Fitting the lead transition lineshape. a) Example linecut (orange) of the lead transition recorded at Pprobe=−78 dBmP_{\mathrm{probe}}=-78\,\mathrm{dBm}. The cosh⁡−2\cosh^{-2} fit (red) captures well the flank of the peak where a Lorentzian model (dashed black) fails. Note the logarithmic y-axis scale and zoom-in on the right flank of the transition to highlight the discrepancy between the two models. b) Fitted hole temperatures THT_H as a function of probe power. c) Quantum capacitance of the lead transition Cq,LC_{q,L}, calculated from the maximum phase shift at the charge transition. Power broadening causes a rise in the linewidth and reduced resonance height as observed for Pprobe>−60 dBmP_{\mathrm{probe}}>-60\,\mathrm{dBm}.

Interdot transition

The dispersive signal at the interdot transition can be evaluated according to:

ΔΦ=Φ0⋅tc2((αP1(VP1−VP10)22)2+tc2)−3/2(6)\Delta\Phi=\Phi_0\cdot t_c^2\left(\left(\frac{\alpha_{P1}(V_{P1}-V_{P10})}{2\sqrt{2}}\right)^2+t_c^2\right)^{-3/2} \tag*{(6)}

Where the constant prefactor Φ0\Phi_0 relates the term for the interdot quantum capacitance Cq,IC_{q,I} with the dispersive shift and tct_c is the interdot tunnel coupling [59]. Note the additional factor 2\sqrt{2} compared to [59], translating the quantum dot detuning axis into the plunger gate voltage axis.

The results of fitting an interdot transition-linecut as a function of PprobeP_{\mathrm{probe}} are depicted in Figure 13. In the regime around Pprobe=−70 dBmP_{\mathrm{probe}}=-70\,\mathrm{dBm}, tc≈22±5 μeVt_c\approx22\pm5\,\mu\mathrm{eV} and Cq,I≈380±70 aFC_{q,I}\approx380\pm70\,\mathrm{aF} are plateauing. Lower powers result in too low signal for reliable fitting while higher powers cause power broadening similar as in the case of the lead transition.

Fitting the interdot transition lineshape

Figure 13. Fitting the interdot transition lineshape. a) Example linecut (orange) and fit (red) of the lead transition recorded at Pprobe=−66 dBmP_{\mathrm{probe}}=-66\,\mathrm{dBm}. b) Fitted tunnel coupling tct_c as a function of probe power. c) Quantum capacitance of the interdot transition Cq,IC_{q,I}, calculated from the maximum phase shift at the charge transition. The signal is generally more unstable as compared to the lead transition, causing higher uncertainties.

References

References

  1. [1]D. Loss and D. P. DiVincenzo, Quantum computation with quantum dots, Physical Review A 57, 120 (1998).DOI
  2. [2]N. W. Hendrickx, W. I. L. Lawrie, M. Russ, F. van Riggelen, S. L. de Snoo, R. N. Schouten, A. Sammak, G. Scappucci, and M. Veldhorst, A four-qubit germanium quantum processor, Nature 591, 580 (2021).DOI
  3. [3]K. Takeda, A. Noiri, T. Nakajima, T. Kobayashi, and S. Tarucha, Quantum error correction with silicon spin qubits, Nature 608, 682 (2022).DOI
  4. [4]S. G. J. Philips, M. T. Madzik, S. V. Amitonov, S. L. de Snoo, M. Russ, N. Kalhor, C. Volk, W. I. L. Lawrie, D. Brousse, L. Tryputen, B. P. Wuetz, A. Sammak, M. Veldhorst, G. Scappucci, and L. M. K. Vandersypen, Universal control of a six-qubit quantum processor in silicon, Nature 609, 919 (2022).DOI
  5. [5]R. Maurand, X. Jehl, D. Kotekar-Patil, A. Corna, H. Bohuslavskyi, R. Lavieville, L. Hutin, S. Barraud, M. Vinet, M. Sanquer, and S. D. Franceschi, A CMOS silicon spin qubit, Nature Communications 7, 13575 (2016).DOI
  6. [6]C. Kloeffel, M. Trif, and D. Loss, Strong spin-orbit interaction and helical hole states in Ge/Si nanowires, Physical Review B 84, 195314 (2011).DOI
  7. [7]C. Kloeffel, M. J. Rančić, and D. Loss, Direct Rashba spin-orbit interaction in Si and Ge nanowires with different growth directions, Physical Review B 97, 235422 (2018).DOI
  8. [8]F. N. M. Froning, M. J. Rančić, B. Hetényi, S. Bosco, M. K. Rehmann, A. Li, E. P. A. M. Bakkers, F. A. Zwanenburg, D. Loss, D. M. Zumbühl, and F. R. Braakman, Strong spin-orbit interaction and q-factor renormalization of hole spins in Ge/Si nanowire quantum dots, Physical Review Research 3, 013081 (2021).DOI
  9. [9]S. Geyer, L. C. Camenzind, L. Cronzomaz, V. Deshpande, A. Fuhrer, R. J. Warburton, D. M. Zumbühl, and A. V. Kuhlmann, Self-aligned gates for scalable silicon quantum computing, Applied Physics Letters 118, 104004 (2021).DOI
  10. [10]F. N. M. Froning, L. C. Camenzind, O. A. H. van der Molen, A. Li, E. P. A. M. Bakkers, D. M. Zumbühl, and F. R. Braakman, Ultrafast hole spin qubit with gate-tunable spin-orbit switch functionality, Nature Nanotechnology 16, 308 (2021).DOI
  11. [11]S. Geyer, B. Hetényi, S. Bosco, L. C. Camenzind, R. S. Eggli, A. Fuhrer, D. Loss, R. J. Warburton, D. M. Zumbühl, and A. V. Kuhlmann, Two-qubit logic with anisotropic exchange in a fin field-effect transistor, arXiv , 2212.02308 (2022).
  12. [12]K. Wang, G. Xu, F. Gao, H. Liu, R.-L. Ma, X. Zhang, Z. Wang, G. Cao, T. Wang, J.-J. Zhang, D. Culcer, X. Hu, H.-W. Jiang, H.-O. Li, G.-C. Guo, and G.-P. Guo, Ultrafast coherent control of a hole spin qubit in a germanium quantum dot, Nature Communications 13, 206 (2022).DOI
  13. [13]L. C. Camenzind, S. Geyer, A. Fuhrer, R. J. Warburton, D. M. Zumbühl, and A. V. Kuhlmann, A hole spin qubit in a fin field-effect transistor above 4 kelvin, Nature Electronics 5, 178 (2022).DOI
  14. [14]L. Petit, H. G. J. Eenink, M. Russ, W. I. L. Lawrie, N. W. Hendrickx, S. G. J. Philips, J. S. Clarke, L. M. K. Vandersypen, and M. Veldhorst, Universal quantum logic in hot silicon qubits, Nature 580, 355 (2020).DOI
  15. [15]C. H. Yang, R. C. C. Leon, J. C. C. Hwang, A. Saraiva, T. Tanttu, W. Huang, J. C. Lemyre, K. W. Chan, K. Y. Tan, F. E. Hudson, K. M. Itoh, A. Morello, M. Piotro-Ladrière, A. Laucht, and A. S. Dzurak, Operation of a silicon quantum processor unit cell above one kelvin, Nature 580, 350 (2020).DOI
  16. [16]Y. Fang, P. Philippopoulos, D. Culcer, W. A. Coish, and S. Chesi, Recent advances in hole-spin qubits, Materials for Quantum Technology 3, 2210.13725 (2022).DOI
  17. [17]S. Bosco and D. Loss, Fully Tunable Hyperfine Interactions of Hole Spin Qubits in Si and Ge Quantum Dots, Physical Review Letters 127, 190501 (2021).DOI
  18. [18]S. Bosco, B. Hetényi, and D. Loss, Hole Spin Qubits in Si FinFETs With Fully Tunable Spin-Orbit Coupling and Sweet Spots for Charge Noise, PRX Quantum 2, 010348 (2021).DOI
  19. [19]N. Piot, B. Brun, V. Schmitt, S. Zihlmann, V. P. Michal, A. Apra, J. C. Abadillo-Uriel, X. Jehl, B. Bertrand, H. Niebosjewski, L. Hutin, M. Vinet, M. Urdampilleta, T. Meunier, Y.-M. Niquet, R. Maurand, and S. D. Franceschi, A single hole spin with enhanced coherence in natural silicon, Nature Nanotechnology 17, 1072 (2022).DOI
  20. [20]D. J. Reilly, C. M. Marcus, M. P. Hanson, and A. C. Gossard, Fast single-charge sensing with a rf quantum point contact, Applied Physics Letters 91, 162101 (2007).DOI
  21. [21]S. J. Angus, A. J. Ferguson, A. S. Dzurak, and R. G. Clark, A silicon radio-frequency single electron transistor, Applied Physics Letters 92, 112103 (2008).DOI
  22. [22]C. Barthel, D. J. Reilly, C. M. Marcus, M. P. Hanson, and A. C. Gossard, Rapid Single-Shot Measurement of a Singlet-Triplet Qubit, Physical Review Letters 103, 160503 (2009).pubmed.ncbi.nlm.nih.gov/19905680
  23. [23]K. Takeda, J. Kamioka, T. Otsuka, J. Yoneda, T. Nakajima, M. R. Delbecq, S. Amaha, G. Allison, T. Kodera, S. Oda, and S. Tarucha, A fault-tolerant addressable spin qubit in a natural silicon quantum dot, Science Advances 2, e1600694 (2016).DOI
  24. [24]M. House, I. Bartlett, P. Pakkiam, M. Koch, E. Peretz, J. van der Heijden, T. Kobayashi, S. Rogge, and M. Simmons, High-Sensitivity Charge Detection with a Single-Lead Quantum Dot for Scalable Quantum Computation, Physical Review Applied 6, 044016 (2016).
  25. [25]G. Oakes, V. Ciriano-Tejel, D. Wise, M. Fogarty, T. Lundberg, C. Lainé, S. Schaal, F. Martins, D. Ibberson, L. Hutin, B. Bertrand, N. Stelmahsenko, J. Robinson, L. Ibbersen, A. Hashim, I. Siddiqi, A. Lee, M. Vinet, C. Smith, J. Morton, and M. Gonzalez-Zalba, Fast High-Fidelity Single-Shot Readout of Spins in Silicon Using a Single-Electron Box, Physical Review X 13, 011023 (2023).arxiv.org/abs/2203.06608
  26. [26]J. I. Colless, A. C. Mahoney, J. M. Hornibrook, A. C. Doherty, H. Lu, A. C. Gossard, and D. J. Reilly, Dispersive Readout of a Few-Electron Double Quantum Dot with Fast rf Gate Sensors, Physical Review Letters 110, 046805 (2013).DOI
  27. [27]M. F. Gonzalez-Zalba, S. Barraud, A. J. Ferguson, and A. C. Betz, Probing the limits of gate-based charge sensing, Nature Communications 6, 6084 (2015). readout of spins in silicon, Nature Nanotechnology 14, 437 (2019).DOI
  28. [29]F. Vigneau, F. Fedele, A. Chatterjee, D. Reilly, F. Kuem- meth, M. F. Gonzalez-Zalba, E. Laird, and N. Ares, Probing quantum devices with radio-frequency reflectom- etry, Applied Physics Reviews 10, 021305 (2023).DOI
  29. [30]M. Urdampilleta, D. J. Niegemann, E. Chanrion, B. Jadot, C. Spence, P.-A. Mortemousque, C. Bäuerle, L. Hutin, B. Bertrand, S. Barraud, R. Maurand, M. Sanquer, X. Jehl, S. D. Franceschi, M. Vinet, and T. Meunier, Gate-based high fidelity spin readout in a CMOS device, Nature Nanotechnology 14, 737 (2019).DOI
  30. [31]Y. Hu, H. O. H. Churchill, D. J. Reilly, J. Xiang, C. M. Lieber, and C. M. Marcus, A Ge/Si heterostructure nanowire-based double quantum dot with integrated charge sensor, Nature Nanotechnology 2, 622 (2007).DOI
  31. [32]Y. Hu, F. K. Kue㎜eth, C. M. Lieber, and C. M. Marcus, Hole spin relaxation in Ge–Si core–shell nanowire qubits, Nature Nanotechnology 7, 47 (2011).DOI
  32. [33]M. Jung, M. D. Schroer, K. D. Petersson, and J. R. Petta, Radio frequency charge sensing in InAs nanowire double quantum dots, Applied Physics Letters 100, 253508 (2012).DOI
  33. [34]A. P. Higginbotham, T. W. Larsen, J. Yao, H. Yan, C. M. Lieber, C. M. Marcus, and F. Kuemmeth, Hole Spin Coherence in a Ge/Si Heterostructure Nanowire, Nano Letters 14, 3582 (2014).DOI
  34. [35]J. H. Ungerer, P. C. Kwon, T. Patlatiuk, J. Ridderbos, A. Kononov, D. Sarmah, E. P. A. M. Bakkers, D. Zumbühl, and C. Schönenberger, Charge-sensing of a ge/si core/shell nanowire double quantum dot using a high-impedance superconducting resonator, Materials for Quantum Technology 3, 031001 (2023).DOI
  35. [36]I. Ahmed, J. A. Haigh, S. Schaal, S. Barraud, Y. Zhu, C. min Lee, M. Amado, J. W. A. Robinson, A. Rossi, J. J. L. Morton, and M. F. Gonzalez-Zalba, Radio-Frequency Capacitive Gate-Based Sensing, Physical Review Applied 10, 014018 (2018).DOI
  36. [37]T. Müller, B. Küng, S. Hellmüller, P. Studerus, K. Ensslin, T. Ihn, M. Reinwald, and W. Wegscheider, An in situ tunable radio-frequency quantum point contact, Applied Physics Letters 97, 202104 (2010).DOI
  37. [38]N. Ares, F. Schupp, A. Mavalankar, G. Rogers, J. Griffiths, G. Jones, I. Farrer, D. Ritchie, C. Smith, A. Cottet, G. Briggs, and E. Laird, Sensitive Radio-Frequency Measurements of a Quantum Dot by Tuning to Perfect Impedance Matching, Physical Review Applied 5, 034011 (2016).DOI
  38. [39]D. J. Ibberson, L. A. Ibberson, G. Smithson, J. A. Haigh, S. Barraud, and M. F. Gonzalez-Zalba, Low-temperature tunable radio-frequency resonator for sensitive dispersive readout of nanoelectronic devices, Applied Physics Letters 114, 123501 (2019).DOI
  39. [40]K. M. Johnson, Variation of dielectric constant with voltage in ferroelectrics and its application to parametric devices, Journal of Applied Physics 33, 2826 (1962).DOI
  40. [41]P. Apostolidis, B. J. Villis, J. F. Chittock-Wood, A. Baumgartner, V. Vesterinen, S. Simbierowicz, J. Hassel, and M. R. Buitelaar, Quantum paraelectric varactors for radio-frequency measurements at mK temperatures, arXiv , 2007.03588 (2020).arxiv.org/abs/2007.03588
  41. [42]M. A. Saifi and L. E. Cross, Dielectric Properties of Strontium Titanate at Low Temperature, Physical Review B 2, 677 (1970).DOI
  42. [43]T. Sakudo and H. Unoki, Dielectric Properties of SrTiO₃ at Low Temperatures, Physical Review Letters 26, 851 (1971).DOI
  43. [44]R. C. Neville, B. Hoeneisen, and C. A. Mead, Permittivity of Strontium Titanate, Journal of Applied Physics 43, 2124 (1972).DOI
  44. [45]J. Hemberger, P. Lunkenheimer, R. Viana, R. Böhmer, and A. Loidl, Electric-field-dependent dielectric constant and nonlinear susceptibility in SrTiO₃, Physical Review B 52, 13159 (1995).
  45. [46]D. Davidovikj, N. Manca, H. S. J. van der Zant, A. D. Caviglia, and G. A. Steele, Quantum paraelectricity probed by superconducting resonators, Physical Review B 95, 214513 (2017).DOI
  46. [47]S. Conesa-Boj, A. Li, S. Koelling, M. Brauns, J. Ridderbos, T. T. Nguyen, M. A. Verheijen, P. M. Koenraad, F. A. Zwanenburg, and E. P. A. M. Bakkers, Boosting Hole Mobility in Coherently Strained [110]-Oriented Ge-Si Core-Shell Nanowires, Nano Letters 17, 2259 (2017).DOI
  47. [48]F. N. M. Froning, M. K. Rehmann, J. Ridderbos, M. Brauns, F. A. Zwanenburg, A. Li, E. P. A. M. Bakkers, D. M. Zumbühl, and F. R. Braakman, Single, double, and triple quantum dots in Ge/Si nanowires, Applied Physics Letters 113, 073102 (2018).DOI
  48. [49]X.-J. Hao, T. Tu, G. Cao, C. Zhou, H.-O. Li, G.-C. Guo, W. Y. Fung, Z. Ji, G.-P. Guo, and W. Lu, Strong and Tunable Spin-Orbit Coupling of One-Dimensional Holes in Ge/Si Core/Shell Nanowires, Nano Letters 10, 2956 (2010).DOI
  49. [50]J. Xiang, W. Lu, Y. Hu, Y. Wu, H. Yan, and C. M. Lieber, Ge/Si nanowire heterostructures as high-performance field-effect transistors, Nature 441, 489 (2006).pubmed.ncbi.nlm.nih.gov/16724062
  50. [51]C. Ang and Z. Yu, dc electric-field dependence of dielectric constant in polar dielectrics: Multipolarization mechanism model, Phys. Rev. B 69, 174109 (2004).DOI
  51. [52]K. Buisman, L. de Vreede, L. Larson, M. Spirito, A. Akhnoukh, T. Scholtes, and L. Nanver, Distortion-Free Varactor Diode Topologies for RF Adaptivity, in IEEE MTT-S International Microwave Symposium Digest (IEEE, 2005).DOI
  52. [53]J.-W. Heo, S. Hong, S.-G. Choi, A. ul Hassan Sarwar Hana, and H.-S. Kim, Characteristics of GaAs varactor diode with hyperabrupt doping profile, physica status solidi (a) 212, 612 (2014).DOI
  53. [54]A. Higginbotham, F. Kuemmeth, T. Larsen, M. Fitzpatrick, J. Yao, H. Yan, C. Lieber, and C. Marcus, Antilocalization of Coulomb Blockade in a Ge/Si Nanowire, Physical Review Letters 112, 216806 (2014).DOI
  54. [55]S. Roddaro, A. Fuhrer, P. Brusheim, C. Fasth, H. Q. Xu, L. Samuelson, J. Xiang, and C. M. Lieber, Spin States of Holes in Ge/Si Nanowire Quantum Dots, Physical Review Letters 101, 186802 (2008).pubmed.ncbi.nlm.nih.gov/18999847
  55. [56]M. Brauns, J. Ridderbos, A. Li, E. P. A. M. Bakkers, and F. A. Zwanenburg, Electric-field dependent g-factor anisotropy in Ge–Si core-shell nanowire quantum dots, Phys. Rev. B 93, 121408 (2016).DOI
  56. [57]A. Zarassi, Z. Su, J. Danon, J. Schwenderman, M. Hocer, B. M. Nguyen, J. Yoo, S. A. Dayeh, and S. M. Frolov, Magnetic field evolution of spin blockade in Ge/Si nanowire double quantum dots, Phys. Rev. B 95, 155416 (2017).DOI
  57. [58]R. Wang, R. S. Deacon, J. Sun, J. Yao, C. M. Lieber, and K. Ishibashi, Gate Tunable Hole Charge Qubit Formed

Paper details

vlnc:W_7726yrcw
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents