betaFeedback

WorksPhysics and Astronomy

The Potential of MXene Materials as a Component in the Catalyst Layer for the Oxygen Evolution Reaction

Abstract

MXenes are a class of 2D/layered materials which are highly conductive, hydrophilic, have a large electrochemical surface area and are easily processible into electrodes for energy applications. Since the discovery of MXenes over ten years ago, these materials have been mainly used in the preparation of electrodes for batteries and supercapacitors. However, due to their aforementioned properties, MXenes could potentially be utilised as a component in the catalyst layer for the Oxygen Evolution Reaction (OER). This opinion piece will discuss some of the recent literature in the area of hybrid catalysts consisting of various Transition Metal Oxides (TMOs) and MXenes for the OER. We will also discuss current drawbacks and future outlook in this new area of research.

Introduction

In an electrolyser device, the catalyst layer can contribute to losses in the overall running of the electrolyser due to inactive OER sites and low conductivity of the materials.[1, 2] To achieve next generation inexpensive OER electrolyser catalysts, the catalysts themselves must be electrically conductive, mechanically and chemically stable under operating conditions, exhibit a high electrochemical surface area, and contain a high concentration of active sites for the evolution of O2O_{2}. This has not been achieved to date for Proton exchange Membrane (PEM) and Alkaline Anion Exchange Membrane (AAEM) water electrolysis. One avenue to explore to make a catalyst that possesses all these characteristics would be to essentially combine different materials that exhibit these properties individually and make a ‘super’ catalyst.

MXenes are a family of 2D materials, which are made up of transition metal carbides and nitrides, produced from MAX phases by various etching and delamination processes, Figure 1A. [3, 4] A MAX phase has the general formula of Mn+1AXnM_{n+1}AX_{n} where the M is an early transition metal, the A is an element from group 13 and 14 of the periodic table, and the X represents a carbon or nitrogen.[5] During the etching process, done in a fluoride ion based solution, the element from group 13/14 is removed from the MAX structure causing the carbide layers to become terminated by OH−\mathrm{OH}^{-}, O−\mathrm{O}^{-}, Cl−\mathrm{Cl}^{-} or F−\mathrm{F}^{-} groups which are subsequently called ‘surface groups or edge sites’.[5] The resulting structure is known as a ‘MXene’.[5, 6]

MXene fabrication, metal oxide suspensions, and number of TMO/MXene papers for the OER

Figure 1. A. MXene fabrication (Reproduced with permission from Zhang et al. [20] Copyright Wiley (2014)) B. Metal Oxide Suspensions (Reproduced with permission from Browne et al. [21] Copyright Royal Society of Chemistry (2021)) C. Number of TMO/MXene papers for the OER (includes published literature from Scopus (01/02/2022) terms used ‘Oxygen Evolution Reaction’ ‘MXene’ and ‘metal oxide’. One paper is a review and one paper is for batteries, not OER).

MXenes are known to be highly conductive, hydrophilic, and tuneable which are all advantageous properties that could lead to improving pure metal oxides when combined in a catalyst layer for OER. [6] As metal oxide materials lack high conductivity, which adds to the overall losses in an electrolytic cell, the addition of MXene materials could provide a high conductive support network making the hybrid material into a superior OER catalyst. Additionally, the hydrophilic nature of the MXenes will allow for the full coverage of OH−\mathrm{OH}^{-} ions on the surface of the catalyst from the electrolyte which should help in the formation of O2O_{2}. Finally, being able to tune the various MXene materials could significantly improve the conductivity and the hydrophilic nature of the MXene, hence further improving the ability to evolve O2O_{2}. However, to date MXenes are not known to contain active sites for the OER, as no MXenes with metals for promoting the OER (e.g. Ni, Ru, Ir, Co, Mn or Fe) have been successfully synthesised (however MXenes containing Mn and Fe have been theoretically reported).[7, 8] Interestingly, for the opposite water splitting reaction, the hydrogen evolution reaction (HER), MXene materials have been proven to be promising through computation calculations and experimentally methods.[9, 10, 11]

On the other hand, Transition Metal Oxides (TMOs) are an exciting group of materials, that possess various intriguing physical properties that can change depending on the oxidation state of the material and are known to be active OER catalysts, Figure 1B.[12, 13] However, these TMO materials exhibit instability and dissolution during operation which renders these materials unsuitable for deployment in large-scale electrolyser devices.[14]

By combining inexpensive, active TMO catalysts with the conductive MXenes, most of the characteristics of the ‘super’ catalysts described previously, i.e. active site density due to the metal oxides and high conductivity due to the MXenes, in theory can be achieved.[15] The MXene materials may also provide a high surface area network for the TMO materials, similar to what has been attempted with carbon nanotubes (CNT) for OER composite materials, in order to improve electron transfer properties.[16] However, CNT based materials are known to contain metal impurities that enhance the OER (unaware to most) and corrodes under anodic OER potentials therefore are not the ideal composite materials with TMOs for the OER.[17, 18] This high surface area network of a TMO/MXene composite will hopefully improve the operational stability of the catalyst layer due to improved mechanical properties.

Finally, combining MXenes and the TMOs may even result in a lower loading of the TMOs, further lowering the catalyst costs. Hence, the combination of TMOs and MXenes into heterostructured layers or functionalising the MXenes with TMOs is a new and exciting avenue to be explored for the generation of highly active OER catalysts in PEM and AAEM electrolysers.[19]

TMO/MXene OER Catalysts in Literature

To date only a hand full of papers have been published in this area, Figure 1C and Table 1. All of these papers have the same overarching conclusion that the addition of MXenes to transition metal oxides improves the initial OER performance compared to the TMO or the MXene alone.

For example, Lu et al. synthesised a hybrid MXene composite with Co3O4\mathrm{Co_3O_4} decorated on Ti3C2Tx\mathrm{Ti_3C_2T_x} MXene flakes by a solvothermal reaction at 150 °C for three hours.[22] The resulting Co3O4/Ti3C2Tx\mathrm{Co_3O_4/Ti_3C_2T_x} hybrid exhibited an OER overpotential of ~ 300 mV at a current density of 10 mA cm−2^{-2} (the current benchmark used in literature when reporting the performance of OER materials) from linear sweep voltammetry measurements, Figure 2A.[22] Under the same OER conditions, the authors reported that a Co3O4\mathrm{Co_3O_4} only material reached the same current density at overpotentials of 390 mV, while the Ti3C2Tx\mathrm{Ti_3C_2T_x} can be deemed OER inactive as the current density at an overpotential of ~400 mV is virtually zero.[22] Furthermore, in this study, Lu and co-workers investigated the effect of the ratio of metal oxide:MXene on the OER. The four ratios of metal oxide:MXene prepared were 1:0.1, 1:0.4, 1:1 and 1:10. The results showed that the lowest amount of MXene to metal oxide (i.e. 1: 0.1) exhibited the best OER results in terms of overpotential at a current density at 10 mA cm−2^{-2}.

Linear sweep voltammetry curves in the OER region for hybrid TMO/MXene materials

Figure 2. Linear Sweep Voltammetry Curves in the OER region showing hybrid TMO/MXene materials outperform their TMO and MXene counterparts from research published by A. Lu et al. (Reproduced with permission from Lu et al. [22] Copyright Elsevier (2020)) B. Benchakar et al. (Reproduced with permission from Benchakar et al. [23] Copyright Wiley (2019)) and C. Yu et al. (Reproduced with permission from Yu et al. [24] Copyright Elsevier (2018)).

Benchakar and co-workers have observed a similar phenomenon for a Co layered double hydroxide (LDH)/Ti3C2Tx\mathrm{Ti_3C_2T_x} material fabricated by a polyol and solvothermal process.[23] In this particular study, the Co LDH/Ti3C2Tx\mathrm{Ti_3C_2T_x} outperformed the unsupported Co LDH for the OER by 50 mV, Figure 2B.[23] The authors have also reported that the MXene structure can be preserved for oxidation during synthesis and the OER by the well distributed Co LDHs on the surface of the MXene. Interestingly, the authors also reported that this Co LDH/Ti3C2Tx\mathrm{Ti_3C_2T_x} hybrid synthesized by chemical routes outperformed a material which consisted of the Co LDH and the Ti3C2Tx\mathrm{Ti_3C_2T_x} mechanically mixed. This increase in performance of the chemically synthesized hybrid compared to the mechanically mixed catalyst was hypothesised to be due to the higher charge transfer resistance due to the close proximity of the Co LDHs and the Ti3C2Tx\mathrm{Ti_3C_2T_x} or the lower amount of active sites in the mechanically mixed material.[23]

Additionally, the integration of MXene materials into a composite with bimetallic TMOs has been shown to be advantageous for the OER. Yu et al. reported that the synthesis of an FeNi-LDH/Ti3C2Tx\mathrm{Ti_3C_2T_x} material, fabricated by the co-precipitation of Fe2+\mathrm{Fe^{2+}} and Ni2+\mathrm{Ni^{2+}} from metal salts with already exfoliated MXene flakes under reflux, which also outperformed its individual counterparts under OER conditions, Figure 2C. The authors attributed the superior OER performance of the composite material to the increase in the charge transfer properties from electrochemical impedance measurements, a shift in the Ni redox peaks to more anodic potential that may induce the OER earlier and an enhancement in the O binding strength of the FeNi LDH due to an electron extraction as a result of the coupling with the MXene. [24]

TMOMXeneSynthesis methodInitial OER performance (Overpotential at 10 mA cm−2^{-2})Experimental reasoning for OER activity from postmortem or in-situ analysisRef
NiFe2_2O4_4Ti3_3C2_2Tx_xHydrothermal266 mVNone given[25]
NiFeTi3_3C2_2Tx_x/ reduced graphene oxideMetal oxides were precipitated and MXene/rGO mixed in235 mVNone given[26]
Co LDHTi3_3C2_2Tx_xPolyol synthesis MixedPolyol: 340 Mixed: Over 520 mVNone given[23]
Co3_3O4_4Ti3_3C2_2Tx_xSolvothermal300 mVNone given[22]
PtO-PdO NPTi3_3C2_2Tx_xSolution Plasma modification310 mVNone given[27]
FeNi LDHsTi3_3C2_2Tx_xionic hetero-assembly – metal salts and MXene refluxed298 mVNone given[24]

Table 1.

Current Drawbacks and Potential Avenues for Success (Outlook)

It is evident from literature that MXenes do significantly enhance the initial performance of TMO catalysts for the OER. However, MXene materials in a water-based solution are known to be unstable in air, Figure 3A.[28] The edge sites/surface groups of the MXene materials will oxidise first (due to deoxygenated species) to produce TiO2_2 which will then lead to the whole flake becoming oxidized and hence decreasing the conductivity of the materials, Figure 3A. This can potentially be a huge problem for any electrochemical energy application including electrolysis.

Image not extracted

Figure 3. A. Showing the decrease in MXene flake stability in air at room temperature (Reproduced with permission from Zhang et al. [28] Copyright American Chemical Society (2017)). B. Multi-cycling of a Co3_3O4_4/Ti3_3C2_2Tx_x hybrid material (Reproduced with permission from Lu et al. [22] Copyright Elsevier (2020)). C. Chronopotentiometry of a FeNi-LDH/Ti3_3C2_2Tx_x material on Ni foam (Reproduced with permission from Yu et al. [24] Copyright (2018)). Grey line with arrow was drawn by authors to show the increase in potential with time.

Unfortunately, the electrochemical instability of hybrid TMO/MXene materials have been already observed in the small amount of literature published in the area to date. For example, Lu et al. multi-cycled their Co3_3O4_4/Ti3_3C2_2Tx_x hybrid in the OER region for 2000 times and observed a significant decrease in activity over time, Figure 3B.[22] Furthermore, a FeNi-LDH/Ti3_3C2_2Tx_x material on Ni foam, synthesized by Yu and co-workers, also exhibited a decrease in activity over time during a chronopotentiometry test at 10 mA cm−2^{-2} for 60 hours, Figure 3C.

The instability of these materials at such low current densities presents a major drawback in the potential for MXenes to be incorporated as a component of an OER catalyst layer. If these hybrid materials are to be employed in large scale electrolysis devices, the materials must remain stable at high current densities of 1 A cm−2^{-2} and higher. In order to alleviate major instabilities in these hybrid materials, investigations using in-situ or operando measurements in conjunction with electrochemical techniques need to be carried out in order to determine the reasoning for the instability of the materials, which is likely to be related to the degradation of the MXene to TiO2_2 under the extreme oxidative conditions present during the OER. The controlled synthesis of hybrid materials that can hinder the instability of the MXene component by covering the edge sites with active materials for the OER is another avenue which can be explored. Benchakar and co-workers have reported that their polyol/solvothermal synthesis method did fabricate a TMO/MXene hybrid material that is OER stable by covering the MXene edge sites with Co LDHs, however no stability tests were conducted to determine the long-term stability, which is needed to learn about possible TMO/MXene instabilities if superior such composite materials are to be designed in the future.[23]

A second route which could be undertaken to improve the OER performance and stability of TMO/MXene hybrids is to explore the (continuously expanding) world of MXenes materials. In literature the only MXene which has been utilised to synthesise TMO/MXene materials is Ti3_3C2_2Tx_x. There are numerous MXene materials now available and all exhibit different chemical and physical properties. [3, 29, 30] These other MXenes may be more stable and/or active for the OER when compared to the most common MXene, Ti3_3C2_2Tx_x. For example, it is well known that the incorporation/presence of Fe based materials/impurities into metal oxides improves the parent oxide towards the OER.[31] Therefore if the theoretically proposed Fe2_2CT2_2 MXene materials could be synthesized,[32] this may lead to an enhancement in the OER activity, while also attaining high conductivity and hydrophilicity of the combined TMO/MXene materials compared to when a non-Fe MXene (e.g. Ti3_3C2_2Tx_x) is present in the hybrid material.

A third route which could be undertaken to improve the performance of the metal oxide/MXene hybrid is to further investigate what ratio of TMO:MXene is optimum for the OER. Lu and co-workers showed that a ratio of 1:0.1 metal TMO:MXene is the best ratio for the OER in their study. However, this 1:0.1 TMO:MXene material contained the lowest ratio of MXene. Therefore, further studies into lower amounts of MXene in the hybrid need to be undertaken to determine if even less MXene is favourable for the OER when combined with metal oxides.

Furthermore, Gogotsi and co-workers have recently reported that MXene materials containing more than one metal can be fabricated with different stoichiometries and can all be tuned in respect to the chemical properties they exhibit.[3] If the chemical properties of the aforementioned mixed metal MXenes can be tuned, this opens up a huge space to investigate the suitability of these TMO/MXene hybrid materials for the OER.

Due to the large volume of TMO/MXene combinations, Density Functional Theory (DFT) will also play a vital role in the screening of the most promising TMO/MXene OER catalysts, as it has done for the HER.[11] DFT calculations, such as free energy and surface Pourbaix diagrams, could be utilised to predict stable surface terminations under OER conditions which could help experimental synthesis of stable TMO/MXene OER catalysts.

Finally, for these hybrid TMO/MXene catalysts to reach a stage of commercialisation, the TMO/MXene materials would need to outperform the current state-of-the-art materials in terms of activity and stability in actual electrolyser devices and not just in a conventional three-electrode cell used in OER studies throughout academia. The reason behind this, is that in a conventional three-electrode cell, it has been shown that OER catalysts do not behave the same as in an electrolyser device.[21, 33, 34] However, to reach a stage of testing TMO/MXene catalysts in an electrolyser device, first more fundamental issues must be tackled including the oxidation of MXenes under OER potentials, the optimum metal oxide to MXene ratio for OER and improving the overall activity of the hybrid catalysts by synthetic/in-situ characterisation feedback mechanisms.

Declaration of interest

Nothing declared

Acknowledgements

M.P.B. would like to acknowledge the European Union's Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 884318 (TriCat4Energy). V.N acknowledges the support of SFI AMBER (12/RC/2278_P2) and the ERC CoG 3D2DPrint (681544).

*of special interest

** of outstanding interest

References

  1. [1]Ayers K: The potential of proton exchange membrane–based electrolysis technology. Current Opinion in Electrochemistry (2019) 18: 9-15.DOI
  2. [2]Jensen AW, Sievers GW, Jensen KD, Quinson J, Arminio-Ravelo JA, Brüser V, Arenz M, Escudero-Escribano M: Self-supported nanostructured iridium-based networks as highly active electrocatalysts for oxygen evolution in acidic media. Journal of Materials Chemistry A (2020) 8(3):1066-1071.
  3. [3]VahidMohammadi A, Rosen J, Gogotsi Y: The world of two-dimensional carbides and nitrides (mxenes). Science (2021) 372(6547):eabf1581.DOI
  4. [4]*Naguib M, Kurtoglu M, Presser V, Lu J, Niu J, Heon M, Hultman L, Gogotsi Y, Barsoum MW: Two-dimensional nanocrystals produced by exfoliation of ti₃alc₂. Advanced Materials (2011) 23(37):4248-4253. First paper to report the exfoliation of a MXene from a Max phase.MXene materials could potentially be used in the catalyst layers of OER materials to increase the conductivity of the whole layer.DOI
  5. [5]Alhabeb M, Maleski K, Anasori B, Lelyukh P, Clark J, Sin S, Gogotsi Y: Guidelines for synthesis and processing of two-dimensional titanium carbide (ti₃c₂tₓ mxene). Chemistry of Materials (2017) 29(18):7633-7644.
  6. [6]Jun B-M, Kim S, Heo J, Park CM, Her N, Jang M, Huang Y, Han J, Yoon Y: Review of mxenes as new nanomaterials for energy storage/delivery and selected environmental applications. Nano Research (2019) 12(3):471-487.DOI
  7. [7]He J, Lyu P, Nachtigall P: New two-dimensional mn-based mxenes with room-temperature ferromagnetism and half-metallicity. Journal of Materials Chemistry C (2016) 4(47):11143-11149.DOI
  8. [8]Li N, Fan J: Computational insights into modulating the performance of mxene based electrode materials for rechargeable batteries. Nanotechnology (2021) 32(25):252001.DOI
  9. [9]Gao G, O’Mullane AP, Du A: 2d mxenes: A new family of promising catalysts for the hydrogen evolution reaction. ACS Catalysis (2017) 7(1):494-500.DOI
  10. [10]Lim KRG, Handoko AD, Johnson LR, Meng X, Lin M, Subramanian GS, Anasori B, Gogotsi Y, Vojvodic A, Seh ZW: 2h-mos₂ on mo₂ctₓ mxene nanohybrid for efficient and durable electrocatalytic hydrogen evolution. ACS Nano (2020) 14(11):16140-16155.DOI
  11. [11]Jin D, Johnson LR, Raman AS, Ming X, Gao Y, Du F, Wei Y, Chen G, Vojvodic A, Gogotsi Y, Meng X: Computational screening of 2d ordered double transition-metal carbides (mxenes) as electrocatalysts for hydrogen evolution reaction. The Journal of Physical Chemistry C (2020) 124(19):10584-10592.DOI
  12. [12]Browne MP, Sofer Z, Pumera M: Layered and two dimensional metal oxides for electrochemical energy conversion. Energy & Environmental Science (2019) 12(1):41-58.DOI
  13. [13]Tyndall D, Jaskaniec S, Shortall B, Roy A, Gannon L, O’Neill K, Browne MP, Coelho J, McGuinness C, Duesberg GS, Nicolosi V: Postsynthetic treatment of nickel–iron layered double hydroxides for the optimum catalysis of the oxygen evolution reaction. npj 2D Materials and Applications (2021) 5(1):73.DOI
  14. [14]Mayerhöfer B, Speck FD, Hegelheimer M, Bierling M, Abbas D, McLaughlin D, Cherevko S, Thiele S, Peach R: Electrochemical- and mechanical stability of catalyst layers in anion exchange membrane water electrolysis. International Journal of Hydrogen Energy (2022) 47(7):4304-4314.DOI
  15. [15]Lin Z, Shao H, Xu K, Taberna P-L, Simon P: Mxenes as high-rate electrodes for energy storage. Trends in Chemistry (2020) 2(7):654-664.DOI
  16. [16]McAteer D, Godwin IJ, Jing Z, Harvey A, He L, Boland CS, Vega-Mayoral V, Szydłowska B, Rovetta AA, Backes C, Boland JB et al: Liquid exfoliated co(oh)₂ nanosheets as low-cost, yet high-performance, catalysts for the oxygen evolution reaction. Advanced Energy Materials (2018) 8(15):1702965.DOI
  17. [17]Browne MP, Domínguez C, Colavita PE: Emerging trends in metal oxide electrocatalysis: Bifunctional oxygen catalysis, synergies and new insights from in situ studies. Current Opinion in Electrochemistry (2018) 7(208-215).DOI
  18. [18]Suryanto BHR, Fang T, Cheong S, Tilley RD, Zhao C: From the inside-out: Leached metal impurities in multiwall carbon nanotubes for purification or electrocatalysis. Journal of Materials Chemistry A (2018) 6(11):4686-4694.DOI
  19. [19]Liu A, Liang X, Ren X, Guan W, Gao M, Yang Y, Yang Q, Gao L, Li Y, Ma T: Recent progress in mxene-based materials: Potential high-performance electrocatalysts. Advanced Functional Materials (2020) 30(38):2003437.DOI
  20. [20]Naguib M, Mochalin VN, Barsoum MW, Gogotsi Y: 25th anniversary article: Mxenes: A new family of two-dimensional materials. Advanced Materials (2014) 26(7):992-1005.DOI
  21. [21]Browne MP, Dodwell J, Novotny F, Jaskániec S, Shearing PR, Nicolosi V, Brett DJL, Pumera M: Oxygen evolution catalysts under proton exchange membrane conditions in a conventional three electrode cell vs. Electrolyser device: A comparison study and a 3d-printed electrolyser for academic labs. Journal of Materials Chemistry A (2021) 9(14):9113-9123.
  22. [22]**Lu Y, Fan D, Chen Z, Xiao W, Cao C, Yang X: Anchoring Co₃O₄ nanoparticles on mxene for efficient electrocatalytic oxygen evolution. Science Bulletin (2020) 65(6):460-466.DOI
  23. [23]**Benchakar M, Bilyk T, Garnero C, Loupias L, Morais C, Pacaud J, Canaff C, Chartier P, Morisset S, Guignard N, Mauchamp V et al: Mxene supported cobalt layered double hydroxide nanocrystals: Facile synthesis route for a synergistic oxygen evolution reaction electrocatalyst. Advanced Materials Interfaces (2019) 6(23):1901328.DOI
  24. [24]**Yu M, Zhou S, Wang Z, Zhao J, Qiu J: Boosting electrocatalytic oxygen evolution by synergistically coupling layered double hydroxide with mxene. Nano Energy (2018) 44(181-190.DOI
  25. [25]Shinde PV, Mane P, Chakraborty B, Sekhar Rout C: Spinel nife₂o₄ nanoparticles decorated 2d ti₃c₂ mxene sheets for efficient water splitting: Experiments and theories. Journal of Colloid and Interface Science (2021) 602(232-241.DOI
  26. [26]Zhu X, Xu C, Wang Y, Wang L, Chang Z, Fang Z, Liu X, Cheng J: The high performance nife layered double hydroxides@ ti₃c₂tₓ/reduced graphene oxide hybrid catalyst for oxygen evolution reaction. Journal of Alloys and Compounds (2022) 894(DOI
  27. [27]Cui B, Hu B, Liu J, Wang M, Song Y, Tian K, Zhang Z, He L: Solution-plasma-assisted bimetallic oxide alloy nanoparticles of pt and pd embedded within two-dimensional ti₃c₂tₓ nanosheets as highly active electrocatalysts for overall water splitting. ACS Applied Materials & Interfaces (2018) 10(28):23858-23873.DOI
  28. [28]Zhang CJ, Pinilla S, McEvoy N, Cullen CP, Anasori B, Long E, Park S-H, Seral-Ascaso A, Shmeliov A, Krishnan D, Morant C et al: Oxidation stability of colloidal two-dimensional titanium carbides (mxenes). Chemistry of Materials (2017) 29(11):4848-4856.DOI
  29. [29]Naguib M, Barsoum MW, Gogotsi Y: Ten years of progress in the synthesis and development of mxenes. Advanced Materials (2021) 33(39):2103393.DOI
  30. [30]Gogotsi Y, Anasori B: The rise of mxenes. ACS Nano (2019) 13(8):8491-8494. Trottochaud L, Young SL, Ranney JK, Boettcher SW: Nickel–iron oxyhydroxide oxygen-evolution electrocatalysts: The role of intentional and incidental iron incorporation. Journal of the American Chemical Society (2014) 136(18):6744-6753.
  31. [32]Li B, Zhou B, Qu Z, Song Q, Jiang Z: Theoretical study on fe₂c mxene as electrode material for secondary battery. Chemical Physics (2021) 548(111223.DOI
  32. [33]Xu D, Stevens MB, Cosby MR, Oener SZ, Smith AM, Enman LJ, Ayers KE, Capuano CB, Renner JN, Danilovic N, Li Y et al: Earth-abundant oxygen electrocatalysts for alkaline anion-exchange-membrane water electrolysis: Effects of catalyst conductivity and comparison with performance in three-electrode cells. ACS Catalysis (2019) 9(1):7-15.DOI
  33. [34]Ehelebe K, Escalera-López D, Cherevko S: Limitations of aqueous model systems in the stability assessment of electrocatalysts for oxygen reactions in fuel cell and electrolyzers. Current Opinion in Electrochemistry (2021) 29(100832.DOI

Paper details

vlnc:W_7b8xed8r
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents