betaFeedback

WorksPhysics and Astronomy

High-Q Millimeter-Wave Acoustic Resonators in Thin-Film Lithium Niobate Using Higher-Order Antisymmetric Modes

Abstract

This letter presents miniature millimeter wave (mmWave, above 30 GHz) acoustic resonators based on a single-layer thin-film lithium niobate (LN) platform. More specifically, we present high performance third-order antisymmetric (A3) mode laterally excited bulk acoustic resonators (XBAR). Compared to prior demonstrations, the proposed platform features a compact footprint due to a smaller lateral wavelength and aperture. We showcase an A3 mode device operating at 39.8 GHz with a high extracted electromechanical coupling (k^2) of 4%, a high 3-dB series resonance quality factor (Q_s) of 97, and a high 3-dB anti-resonance quality factor (Q_p) of 342, leading to a figure of merit (FoM=k^2*Q_p) of 13.7 with a footprint of 32x44 micron^2. To demonstrate frequency scalability, the piezoelectric film thickness is varied while keeping the device layout. As a result, we present a multitude of high-performance devices covering a wide frequency range of 30-50 GHz, validating the proposed XBAR design at mmWave.

Introduction

With the pervasiveness of 5G wireless communication, compact front-end signal processing components at millimeter-wave (mmWave, above 30 GHz) have garnered attention [1, 2, 3, 4]. Below 6 GHz, surface acoustic wave (SAW) and bulk acoustic wave (BAW) devices - based on piezoelectric materials such as aluminum nitride (AlN), scandium aluminum nitride (ScAlN), lithium niobate (LN), and lithium tantalate (LT) - have been instrumental in realizing miniature filters for mobile applications [5, 6, 7]. However, scaling these technologies to mmWave introduces intrinsic limitations, posing a challenge for the next generation of high-frequency mobile communication systems [8], [9].

Despite significant advances in state-of-the-art radio frequency acoustic technologies, inherent limitations to frequency scaling continue to motivate investigations into alternative platforms. Solidly mounted devices have recently achieved very high phase velocities, but they necessitate sub-100 nm feature patterning alongside expensive substrates, e.g. silicon carbide (SiC) and diamond [10], [11]. Cross-sectional Láme mode resonators exhibit high phase velocity and QQ, yet they also require fine features [12, 13, 14]. Film bulk acoustic

wave resonators (FBAR) exhibit potential for mmWave utilizing acoustic overtones or periodically poled piezoelectric films (P3F), but they face challenges with moderate QQ, primarily due to the large metal to piezoelectric volume ratio at the required film thickness [15].

Alternatively, recent progress in thin-film transfer technology has enabled first-order antisymmetric (A1) mode laterally excited acoustic wave resonators (XBAR) in lithium niobate (LN), without the need for a bottom electrode [4]. However, while recent mmWave XBAR prototypes have reported high electro-mechanical coupling (k2k^2), they have shown moderate QQ [16, 17, 18, 19], yielding a moderate figure of merit (FoM, Q⋅k2Q\cdot k^2, Figure 1). To address the limitations, recent efforts developed P3F LN XBARs, achieving QQ as high as 237 at 50 GHz using bilayer LN [22, 23, 24, 25]. Nevertheless, the P3F structure introduces new fabrication limitations, particularly in maintaining precise thickness control over each layer. These implications motivate a revisit of single-layer XBARs with a new design strategy.

Survey of acoustic resonator performance at 10–60 GHz

Figure 1. A survey of acoustic resonator performance at 10-60 GHz, including prior single-layer LN [16, 17, 18, 19], single-layer AlN and ScAlN [13, 14, 15], [20], [21], P3F LN [22, 23, 24, 25], and P3F ScAlN [26, 27, 28]. We use the obtained 3-dB QpQ_p to compare with previously reported FoMs, where the higher value between the self-reported QsQ_s and QpQ_p was used.

In this work, we present high-performance single-layer mmWave acoustic resonators by minimizing their footprint and maximizing the device volume-to-area ratio. We present devices spanning 30-50 GHz, covering a broad portion of the mmWave spectrum. Notably, we highlight a miniature XBAR at 39.83 GHz with a 3-dB series resonance (fsf_s) quality factor (QsQ_s) of 97, a high 3-dB antiresonance (fpf_p) quality factor (QpQ_p) of 342, and an extracted k2k^2 of 4%. Based on the extracted k2k^2 and 3-dB QpQ_p, the device achieves a high FoM of 13.8 with a compact footprint of 32×44 μm232 \times44\ \mu\mathrm{m}^2.

Cross-sectional view of the chosen acoustic stack

Figure 2. The cross-sectional view of the chosen acoustic stack.

Top view of the finalized device design

Figure 5. (a) Top view of the finalized device design. The key design parameters are labeled.

A3 mode dispersion analysis

Figure 3. A3 Mode dispersion analysis in 128Y LN under electrically open and short boundary conditions with air feedthrough. Calculated coupling is labeled.

FEA simulation

Figure 6. FEA simulation using the parameters listed in Fig. 5.

Device Design

Suspended acoustic resonators were designed in a 128Y LN/amorphous silicon/sapphire stack (Fig. 2). We selected a sample with LN film thickness ranging from 110 to 160 nm to investigate device performance from 30 to 50 GHz.

Diverging from the conventional XBAR design space with long lateral wavelengths (λLateral\lambda_\mathrm{Lateral}), the devices were made compact by reducing λLateral\lambda_\mathrm{Lateral} to 3.15 μ\mum and 4 μ\mum. This choice was made by inspecting the third-order antisymmetric Lamb mode (A3) dispersion curves, enabling a trade-off between λLateral\lambda_\mathrm{Lateral} to achieve a higher k2k^2 (Fig. 3). While prior research indicates that a higher λLateral\lambda_\mathrm{Lateral} is preferred due to superior spurious-mode performance for A1, we specifically tailored the design for A3 operation at mmWave [29]. Utilizing the low chosen λLateral\lambda_\mathrm{Lateral}, the device footprint was reduced for compactness and to minimize surface losses in the acoustic resonator, which arise from both the electrical and the mechanical domains and significantly impact overall device performance [30].

Next, the electrode material and thickness were examined to account for their substantial impact on device performance at reduced piezoelectric film thicknesses. Aluminum (Al) was selected for its excellent conductivity and low mass-loading. The electrode thickness was analyzed using COMSOL finite element analysis (FEA). Strong mechanical damping was assigned in the electrodes, where a low QQ of 5 was chosen as a nominal value for the metal to highlight its effects on the overall performance. On the other hand, LN was modelled as a low-loss structure. With this approach, we gained insights into relative trends in QQ as the ratio of metal to LN decreased.

Simulations conducted with a 50% electrode duty cycle reveal that reducing the electrode thickness yields a higher impedance ratio and consequently leads to a higher overall QQ [Fig. 4 (a)(b)]. In this work, we selected an electrode thickness of 50 nm Al. While variations in the duty cycle can further influence impedance characteristics, a 50% duty cycle was maintained while considering its effect on the feature size. Additionally, a minimized device aperture of 8λLateral8\lambda_\mathrm{Lateral} was selected to mitigate the routing resistance from the electrodes. These design choices enhance overall QQ while maintaining a balance between performance at fsf_s and fpf_p.

The top view of the resulting design can be seen in Fig. 5, where key design parameters are labeled. The FEA simulated admittance with a 4 μ\mum λLateral\lambda_\mathrm{Lateral} shows mmWave operation and a high extracted k2k^2 of 6.4% at 47.7 GHz (Fig. 6), which is obtained from an equivalent Butterworth-Van-Dyke (BVD) model with two motional branches.

Fabrication and Experimental Results

The fabrication steps are outlined in Fig. 7 (a). The process follows closely with [31]. A scanning electron microscope image is in Fig. 7 (b). The XBAR resonators were measured using a Keysight vector network analyzer (VNA) at an input power of −15 dBm, and calibrated with a GGB CS-5 substrate. Due to the miniature footprint, the devices exhibited a parasitic electromagnetic resonance well above their acoustic response. Accordingly, we report raw data from the calibrated VNA.

The measured admittance magnitude and phase of a representative device are in Figure 8. The device exhibited fsf_s at 39.83 GHz with a 3-dB QsQ_s of 97 and fpf_p at 40.67 GHz with a 3-dB QpQ_p of 342. The measurement is further fit with an mBVD model with series routing resistance (RsR_s) and inductance (LsL_s). [25]. The mBVD fit shows good agreement with the measured data. The A3 XBAR showed a motional inductance (LmL_m) of 19 nH, a motional capacitance (CmC_m) of 0.8 fF, a motional resistance (RmR_m) of 18.6 Ω, series resistance (RsR_s) of 18.42 Ω, a series inductance (LsL_s) of 0.1 nH, mBVD QQ (QmBVDQ_{mBVD}) of 260, and an extracted k2k^2 of 4%. QpQ_p and QmBVDQ_{mBVD} are slightly different, due to the limited motional branches in the fit. In comparison with the SoA (Figure 1), the high achieved 3-dB QpQ_p, alongside the extracted k2k^2, leads to a high FoM of 13.8 at 40 GHz, highlighting the effectiveness of the proposed design. To validate the extracted QpQ_p of A3 against potential dynamic range limitations of the VNA, we plot the open response (with probe unlanded), which confirms sufficient dynamic range margin for A3, and supports the reliability of the QpQ_p extraction. The higher measured QsQ_s of A1 over A3 suggests increased resistive, EM, and mechanical losses at higher frequencies. To clarify, Figure 4 only considers the mechanical damping, indicating that mechanical loss in the electrodes affects QsQ_s disproportionately compared with QpQ_p, which is a previously underappreciated loss mechanism at series resonance. Still,

FEA simulations of resonators with varying electrode thicknesses

Figure 4. FEA simulations of resonators with varying electrode thicknesses at (a) series and (b) parallel resonances, indicating the effects of thin electrodes.

Measured wide-band response alongside an mBVD fit

Figure 8. Measured wide-band response alongside an mBVD fit accounting for routing resistance and inductance. Note that in high QpQ_p for A1 mode is not realistic, as the impedance is too high for VNA testing. On the other hand, the QpQ_p for A3 is within the VNA dynamic range.

Fabrication flow and scanning electron microscope image of the fabricated device

Figure 7. (a) The fabrication flow for this work. (b) A Scanning electron microscope (SEM) image of the fabricated device.

isolating a single dominant loss mechanism at mmWave remains difficult due to the combined influence of resistive, EM, and surface effects [22], [30], [32]. Addressing this interplay will be crucial to future high-QQ resonator designs. Additionally, it is notable that the extracted k2k^2 here is significantly smaller than the perceived k2k^2 directly calculated from π2/8⋅((fp/fs)2−1)\pi^2/8\cdot((f_p/f_s)^2-1), due to the EM self-resonance [25]. Accordingly, we report only the extracted values from fitting to avoid unnecessary overclaims. Measurements with the same device layout across 30-50 GHz consistently show high performance (Figure 9). Across this frequency span, QsQ_s ranged from 33 to 102, and QpQ_p from 210 to 464. QpQ_p decreased linearly with frequency, attributed to the increasing acoustic and dielectric loss at higher frequencies. Conversely, QsQ_s was predominantly limited by the resistive and mechanical loss arising from the thin Al electrodes. Hence, based on the extracted k2k^2 and 3-dB QpQ_p, we obtain FoMs ranging from 8 to 22.3 within 30-50 GHz (Figure 1).

Measured 3-dB $Q_s$ and $Q_p$ and extracted $k^2$ from mBVD

Figure 9. (a) Measured 3-dB QsQ_s and QpQ_p, indicating high performance from 35-50 GHz. (b) Extracted k2k^2 from mBVD.

Table 1 benchmarks the proposed mmWave resonators against prior single-layer LN XBARs [16, 17, 18, 19], [33]. Our devices significantly exceed state-of-the-art XBARs in terms of the f⋅Qf\cdot Q product, achieving up to 1.4×10131.4\times10^{13} while maintaining a compact normalized footprint to achieve 50 Ω at fsf_s. These improvements primarily result from key innovations: a compact resonator design thanks to a reduced λlateral\lambda_{lateral} combined with a minimized transverse aperture; and thin (50 nm) electrodes to lower mechanical loss. In tandem, these design enhancements allow resonators to achieve a high QpQ_p at mmWave frequencies. Future mmWave LN XBAR iterations will focus on systematically optimizing key device parameters, including electrode thickness, metal composition and quality, the electrode duty cycle, and the anchor geometry. Additionally, we will explore post-processing techniques such as annealing for further potential reduction in loss. Future device scaling for practical filter applications will focus on shorter aperture lengths and optimized electrode arrays, accompanied by thicker buslines to minimize routing resistance and improve QQ.

Ref.Lateral Wave. (μm)Electrode Thick. (nm)Normalized Footprint (μm²)fsf_s (GHz)k2∗∗k^{2**}3-dB QsQ_s3-dB QpQ_pf⋅Q∗∗∗f\cdot Q^{***}
[33]4503162428%4001001.6E12
[16]83501377575.5%60603.4E12
[17]2050192012.93.8%2822143.7E12
[18]1360202812.83.7%2242242.9E12
[19]343103600033.73.7%67672.3E12
This Work45085729.84.8%1024641.4E13
This Work3.25062636.84.8%333601.3E13
This Work450684404%963421.4E13
This Work3.25056448.83.8%582101.0E13

Table 1. Comparison to Prior Single-Layer LN XBARs. *Impedance at series resonance normalized to 50 Ω. **k2k^2 is the extracted value from fitting. ***QQ is selected as the maximum between reported QsQ_s and QpQ_p.

Conclusion

In this work, we have demonstrated miniature, high-performance A3 XBARs from 30 to 50 GHz. The compact structure outperforms the SoA, highlighting the frequency scalability. This alternative approach tailors the device design to achieve a high QQ at mmWave. With continued optimization, the A3 mode XBAR platform is poised to introduce low-loss acoustic resonators at mmWave frequencies.

References

  1. [1]A. Hagelauer et al., “From Microwave Acoustic Filters to Millimeter-Wave Operation and New Applications,” IEEE J. Microw., vol. 3, no. 1, pp. 484–508, Jan. 2023, doi: 10.1109/JMW.2022.3226415.DOI
  2. [2]U. Gustavsson et al., “Implementation Challenges and Opportunities in Beyond-5G and 6G Communication,” IEEE J. Microw., vol. 1, no. 1, pp. 86–100, Jan. 2021, doi: 10.1109/JMW.2020.3034648.DOI
  3. [3]S. Mahon, “The 5G Effect on RF Filter Technologies,” IEEE Trans. Semicond. Manuf., vol. 30, no. 4, pp. 494–499, Nov. 2017, doi: 10.1109/TSM.2017.2757879.DOI
  4. [4]R. Lu and S. Gong, “RF acoustic microsystems based on suspended lithium niobate thin films: advances and outlook,” J. Micromechanics Microengineering, vol. 31, no. 11, p. 114001, Nov. 2021, doi: 10.1088/1361-6439/ac288f.DOI
  5. [5]E. Guerrero, A. Gimenez, W. Heeren, and M. Al-Joumayly, “BAW Filter Trends for 5G and Beyond,” in 2024 IEEE International Microwave Filter Workshop (IMFW), Feb. 2024, pp. 75–77. doi: 10.1109/IMFW59690.2024.10477135.DOI
  6. [6]Y. Yang, R. Lu, and S. Gong, “Scaling Acoustic Filters Towards 5G,” in 2018 IEEE International Electron Devices Meeting (IEDM), Dec. 2018, p. 39.6.1-39.6.4. doi: 10.1109/IEDM.2018.8614699.DOI
  7. [7]J. P. Smith and V. Hinson-Smith, “The new era of SAW devices,” Anal. Chem., vol. 78, no. 11, pp. 3505–3507, Jun. 2006, doi: 10.1021/ac0694122.DOI
  8. [8]V. V. Felmetsger, P. N. Laptev, and R. J. Graham, “Deposition of ultrathin AlN films for high frequency electroacoustic devices,” J. Vac. Sci. Technol. A, vol. 29, no. 2, p. 021014, Feb. 2011, doi: 10.1116/1.3554718.DOI
  9. [9]E. Iborra, J. Olivares, M. Clement, L. Vergara, A. Sanz-Hervás, and J. Sangrador, “Piezoelectric properties and residual stress of sputtered AlN thin films for MEMS applications,” Sens. Actuators Phys., vol. 115, no. 2, pp. 501–507, Sep. 2004, doi: 10.1016/j.sna.2004.03.053.DOI
  10. [10]J. Campbell et al., “21.4 GHz Surface Acoustic Wave Resonator with 11,400 m/s Phase Velocity in Thin-Film Lithium Niobate on Silicon Carbide,” in 2024 IEEE Ultrasonics, Ferroelectrics, and Frequency Control Joint Symposium (UFFC-JS), Sep. 2024, pp. 1–4. doi: 10.1109/UFFC-JS60046.2024.10793880.
  11. [11]J. Campbell et al., “52-GHz Surface Acoustic Wave Resonators in Thin-Film Lithium Niobate on Silicon Carbide,” IEEE Trans. Ultrason. Ferroelectr. Freq. Control, vol. 72, no. 2, pp. 275–282, Feb. 2025, doi: 10.1109/TUFFC.2024.3522042.DOI
  12. [12]I. Anderson et al., “Low-Loss Higher-Order Cross-Sectional Lamé Mode SAW Devices in 10-20 GHz Range,” in 2024 IEEE Ultrasonics, Ferroelectrics, and Frequency Control Joint Symposium (UFFC-JS), Sep. 2024, pp. 1–4. doi: 10.1109/UFFC-JS60046.2024.10794098.
  13. [13]G. Giribaldi, L. Colombo, and M. Rinaldi, “6–20 GHz 30% ScAlN Lateral Field-Excited Cross-Sectional Lamé Mode Resonators for Future Mobile RF Front Ends,” IEEE Trans. Ultrason. Ferroelectr. Freq. Control, vol. 70, no. 10, pp. 1201–1212, Oct. 2023, doi: 10.1109/TUFFC.2023.3312913.DOI
  14. [14]G. Giribaldi, L. Colombo, P. Simeoni, and M. Rinaldi, “Compact and wideband nanoacoustic pass-band filters for future 5G and 6G cellular radios,” Nat. Commun., vol. 15, no. 1, p. 304, Jan. 2024, doi: 10.1038/s41467-023-44038-9.DOI
  15. [15]Z. Schaffer, P. Simeoni, and G. Piazza, “33 GHz Overmoded Bulk Acoustic Resonator,” IEEE Microw. Wirel. Compon. Lett., vol. 32, no. 6, pp. 656–659, Jun. 2022, doi: 10.1109/LMWC.2022.3166682.
  16. [16]J. Kramer et al., “57 GHz Acoustic Resonator with k2 of 7.3 % and Q of 56 in Thin-Film Lithium Niobate,” in 2022 International Electron Devices Meeting (IEDM), Dec. 2022, p. 16.4.1-16.4.4. doi: 10.1109/IEDM45625.2022.10019391.DOI
  17. [17]Y. Yang, R. Lu, L. Gao, and S. Gong, “10–60-GHz Electromechanical Resonators Using Thin-Film Lithium Niobate,” IEEE Trans. Microw. Theory Techn., vol. 68, no. 12, pp. 5211–5220, Dec. 2020, doi: 10.1109/TMTT.2020.30207694.DOI
  18. [18]Y. Yang, R. Lu, T. Manzaneque, and S. Gong, “Toward Ka Band Acoustics: Lithium Niobate Asymmetrical Mode Piezoelectric MEMS Resonators,” in 2018 IEEE International Frequency Control Symposium (IFCS), May 2018, pp. 1–5. doi: 10.1109/IFCS.2018.8597475.DOI
  19. [19]S. Link, R. Lu, Y. Yang, A. E. Hassanien, and S. Gong, “An A1 Mode Resonator at 12 GHz using 160nm Lithium Niobate Suspended Thin Film,” in 2021 IEEE International Ultrasonics Symposium (IUS), Sep. 2021, pp. 1–4. doi: 10.1109/IUS52206.2021.9593341.DOI
  20. [20]M. Park, Z. Hao, D. G. Kim, A. Clark, R. Dargis, and A. Ansari, “A 10 GHz Single-Crystalline Scandium-Doped Aluminum Nitride Lamb-Wave Resonator,” in 2019 20th International Conference on Solid-State Sensors, Actuators and Microsystems & Eurosensors XXXIII (TRANSDUCERS & EUROSENSORS XXXIII), Jun. 2019, pp. 450–453. doi: 10.1109/TRANSDUCERS.2019.8888374.DOI
  21. [21]D. Mo, S. Dabas, S. Rassay, and R. Tabrizian, “Complementary-Switchable Dual-Mode SHF Scandium Aluminum Nitride BAW Resonator,” IEEE Trans. Electron Devices, vol. 69, no. 8, pp. 4624–4631, Aug. 2022, doi: 10.1109/TED.2022.3183963.DOI
  22. [22]J. Zheng, Z. Ren, J. Xu, X. Liu, F. Qian, and Y. Yang, “Periodically Poled Piezoelectric Single-Layered and Multilayered Lithium Niobate for Thickened High-Order Lamb Wave Acoustic Devices,” IEEE Trans. Microw. Theory Techn., pp. 1–11, 2025, doi: 10.1109/TMTT.2025.3567329.DOI
  23. [23]R. Lu, Y. Yang, S. Link, and S. Gong, “Enabling Higher Order Lamb Wave Acoustic Devices With Complementarily Oriented Piezoelectric Thin Films,” J. Microelectromechanical Syst., vol. 29, no. 5, pp. 1332–1346, Oct. 2020, doi: 10.1109/JMEMS.2020.3007590.DOI
  24. [24]J. Kramer et al., “Thin-Film Lithium Niobate Acoustic Resonator with High Q of 237 and k2 of 5.1% at 50.74 GHz,” in 2023 Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS), May 2023, pp. 1–4. doi: 10.1109/EFTF/IFCS57587.2023.10272149.DOI
  25. [25]J. Kramer et al., “Acoustic resonators above 100 GHz,” Appl. Phys. Lett., vol. 127, no. 1, Jul. 2025, doi: 10.1063/5.0275691.
  26. [26]S. Nam, W. Peng, P. Wang, D. Wang, Z. Mi, and A. Mortazawi, “A mm-Wave Trilayer AlN/ScAlN/AlN Higher Order Mode FBAR,” IEEE Microw. Wirel. Technol. Lett., vol. 33, no. 6, pp. 803–806, Jun. 2023, doi: 10.1109/LMWT.2023.3271865.DOI
  27. [27]Izhar et al., “A High Quality Factor, 19-GHz Periodically Poled AlScN BAW Resonator Fabricated in a Commercial XBAW Process,” IEEE Trans. Electron Devices, vol. 71, no. 9, pp. 5630–5637, Sep. 2024, doi: 10.1109/TED.2024.3435175.DOI
  28. [28]Izhar et al., “Periodically poled aluminum scandium nitride bulk acoustic wave resonators and filters for communications in the 6G era,” Microsyst. Nanoeng., vol. 11, no. 1, p. 19, Jan. 2025, doi: 10.1038/s41378-024-00857-4.DOI
  29. [29]R. Lu, Y. Yang, M.-H. Li, M. Breen, and S. Gong, “5-GHz Antisymmetric Mode Acoustic Delay Lines in Lithium Niobate Thin Film,” IEEE Trans. Microw. Theory Tech., vol. 68, no. 2, pp. 573–589, Feb. 2020, doi: 10.1109/TMTT.2019.2949808.DOI
  30. [30]M. Weinberg, R. Candler, S. Chandorkar, J. Varsanik, T. Kenny, and A. Duwel, “Energy loss in MEMS resonators and the impact on inertial and RF devices,” in TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference, Jun. 2009, pp. 688–695. doi: 10.1109/SENSOR.2009.5285418.
  31. [31]V. Chulukhadze et al., “Frequency Scaling Millimeter Wave Acoustic Resonators using Ion Beam Trimmed Lithium Niobate,” in 2023 Joint Conference of the European Frequency and Time Forum and IEEE International Frequency Control Symposium (EFTF/IFCS), May 2023, pp. 1–4. doi: 10.1109/EFTF/IFCS57587.2023.10272038.DOI
  32. [32]L. Colombo et al., “Characterization of Acoustic Losses in Interdigitated VHF to mmWave Piezoelectric M/NEMS Resonators,” in 2024 IEEE Ultrasonics, Ferroelectrics, and Frequency Control Joint Symposium (UFFC-JS), Sep. 2024, pp. 1–4. doi: 10.1109/UFFC-JS60046.2024.10794128.DOI
  33. [33]Y. Yang, R. Lu, L. Gao, and S. Gong, “4.5 GHz Lithium Niobate MEMS Filters with 10% Fractional Bandwidth for 5G Front-ends,” J. Microelectromechanical Syst., vol. 28, no. 4, pp. 575–577, Aug. 2019, doi: 10.1109/JMEMS.2019.2922935.DOI

Paper details

vlnc:W_7j3dfhdf
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 5

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents