betaFeedback

WorksPhysics and Astronomy

Scintillation characteristics of an undoped CsI crystal at low-temperature for dark matter search

Abstract

The scintillation characteristics of 1 g undoped CsI crystal were studied by directly coupling two silicon photomultipliers(SiPMs) over a temperature range from room temperature to 86 K. The scintillation decay time and light output were measured using x-ray and gamma-ray peaks from a 109Cd radioactive source. An increase in decay time was observed as the temperature decreased from room temperature to 86 K, ranging from 76 ns to 605 ns. The light output also increased, reaching 26.2 +/- 1.3 photoelectrons per keV electron-equivalent at 86 K. Leveraging the significantly enhanced scintillation light output of the undoped CsI crystal at low temperatures, coupling it with SiPMs results in a promising detector for rare event searches. Both cesium and iodine have an odd number of protons, making them suitable targets for probing dark matter-proton spin-dependent interactions. This study evaluates the sensitivity of the proposed detector to such interactions, incorporating the Migdal effect and assuming 200 kg of undoped CsI crystals for dark matter searches. The results indicate that undoped CsI coupled with SiPM can achieve world-competitive sensitivity for low-mass dark matter detection, particularly in the context of dark matter-proton spin-dependent interactions.

Introduction

Scintillating crystals are widely employed in the search for rare event interactions such as dark matter [1, 2, 3, 4, 5, 6] or coherent elastic neutrino-nucleus scattering (CEνNS) [7, 8]. Since event rates are larger at low energy, low threshold detectors are essential for dark matter or CEνNS detection. In the case of scintillators, higher light yields are strongly associated with lower energy thresholds. The introduction of dopants during crystal growth, such as thallium in halide crystals (i.e., CsI(Tl) and NaI(Tl)), enhances radiative recombination and improves light emission efficiency. These doped crystals have been widely utilized at room temperature, coupled with photomultipliers, for dark matter and CEνNS detection experiments [7, 8, 9, 10, 11, 12, 13, 14]. The highest reported light yields for undoped NaI(Tl) crystals were 22 photoelectrons (PE) per keV [8] with a novel crystal encapsulation technique [15]. There have been reports suggesting that undoped CsI and NaI crystals exhibit higher light yields at low temperatures with PMTs [16, 17, 18, 19, 20, 21, 22] or silicon photomultipliers (SiPMs) [23]. At the liquid nitrogen temperature of 77 K, the undoped CsI crystal, coupled with SiPMs and a wavelength shifter, achieved a light yield of 30.1 PE/keV [24]. We investigate the scintillation characteristics of an undoped CsI crystal to assess their temperature-dependent behavior. To maximize the light collection efficiency of the undoped CsI crystal, two SiPMs are directly attached to the crystal. In a temperature range between 86 K and 293 K, we measured the light yield, scintillation decay time, and energy resolution. Due to the exhibition of high dark count rates and crosstalks [25, 26], we have carefully analyzed and corrected effects of them on the analysis of measurements. The technique for radiopure CsI crystal growth [27, 28, 29] has been developed for the KIMS experiment, which used CsI(Tl) crystals coupled with photomultipliers (PMTs) for WIMP dark matter search [30, 31, 32]. The production of 200 kg undoped CsI crystals can be performed at the Institute for Basic Science (IBS), Korea, which offers a powder purification facility [33, 34, 35] and Kyropoulos crystal growers [36], installed and employed for the growth of radiopure NaI(Tl) crystals [37, 38]. Additionally, about 400 kg of purified CsI powder remnants from the KIMS CsI(Tl) crystal growing have been stored at the Yangyang underground laboratory. We conducted a feasibility study for rare event searches by measuring the characteristics of a small size undoped CsI crystal. Based on the high light yield observed from these measurements and the low-background CsI crystal growing technology, we evaluate the dark matter detection sensitivities of a future experiment using a detector based on undoped CsI crystals coupled to SiPMs. In the low-mass dark matter region for the dark matter-proton spin-dependent interaction, this detector can reach a world competitive sensitivity, exploring a new dark matter parameter space.

Scintillation characteristics of the undoped CsI crystal

Experimental setup

The detector assembly used in this study consists of an undoped CsI crystal from the Institute for Scintillation Materials (ISMA) in Ukraine and two SiPMs from Hamamatsu Photonics. The undoped CsI crystal has dimensions of 5.8 mm ×\times 5.9 mm ×\times 7.0 mm with a mass of 1.0 g, as illustrated in Figure 1 (a). Two SiPMs (model number S13360-2172) with an active area of 6.0 mm ×\times 6.0 mm were directly attached to two ends of the crystal. The crystal and the SiPMs were mechanically attached without any optical coupling due to uncertainties regarding the optical grease and optical pad clarities, which were not guaranteed for temperature below −60 ∘C-60\,^\circ\mathrm{C}. This SiPM consists of 14,400 micropixel arrays, each of size 50 μm\mu\mathrm{m} ×\times 50 μm\mu\mathrm{m}, covered with a quartz window. The entire assembly was tightly wrapped with soft polytetrafluoroethylene (PTFE) sheets and connected to homemade readout boards (customization available from NOTICE Korea 1) equipped with electronics for signal readout, pre-amplification, and bias voltage supply, as depicted in Figure 1 (b).

A 5.8 mm × 5.9 mm × 7.0 mm undoped CsI crystal and experimental assembly

Figure 1. A 5.8 mm ×\times 5.9 mm ×\times 7.0 mm undoped CsI crystal is employed for the experiment (a). The crystal is coupled with two SiPMs, enclosed with multiple layers of soft polytetrafluoroethylene (PTFE) sheets, and connected to readout boards (b). Crystal and SiPM are in contact with a copper plate for heat transfer, while the readout board is positioned on an insulator to prevent heat transfer to the detector (c). The entire assembly is placed inside a cryostat chamber.

The CsI-SiPMs setup was installed inside a cryostat vacuum chamber equipped with a temperature control unit,

as depicted in Figure 2. The liquid nitrogen dewar is connected to the copper plate through a thermal link composed of multiple copper wires. The CsI-SiPMs setup was mounted on the copper plate and covered with a radiation shield made of iron to protect against external radiation heat. Rubber insulators were introduced to prevent the conduction of heat from the readout board, as shown in Figure 1 (b). To control the temperatures of the CsI crystal, two heaters were incorporated on the copper plate. Two PT-1000 temperature sensors were employed to monitor the temperature inside the chamber using the temperature control unit of Lake Shore Model 336. One sensor was placed in close proximity to the crystal, while the other was positioned at the edge of the copper plate. The temperature control unit regulates the heater to manage crystal (or system) temperature variations, maintaining a stability level of 0.1 degree. We optimized the thermal connection performance between the nitrogen dewar and copper plate to achieve a minimum temperature closer to 77 K while ensuring efficient heat transfer to the crystal to increase its temperature when necessary. In this setup, we successfully reached a temperature of 86 K with both SiPMs and readout boards in operation.

Figure 2. Schematic drawing of the experimental setup.

A KEITHLEY 2635B SYSTEM SourceMeter is employed to provide the SiPM bias voltage through the readout boards, which are operated with a low-voltage supply using a KEYSIGHT E3630A. The homemade readout electronics amplifies the SiPM signals, and the amplified signals are digitized using a 125 MHz, 12-bit flash-analog-to-digital converter (FADC) supplied by NOTICE Korea.

Measurements

The performance of the SiPM is affected by the overvoltage, defined as ΔV=Vbias−Vbreakdown\Delta V = V_{\mathrm{bias}} - V_{\mathrm{breakdown}}, where VbreakdownV_{\mathrm{breakdown}} is the breakdown voltage. Data were collected using six different overvoltages ranging from 3 V to 8 V, with a 1 V interval at room temperature. The gain, represented by the maximum height of single photoelectron pulses, was evaluated at each overvoltage. Since the photo detection efficiency (PDE) of SiPM varies with gain or overvoltage [39, 40, 41, 42, 43, 44, 45], we maintained a consistent overvoltage for the temperature-dependent measurements. The temperature range for detector testing spanned from 86 K to 293 K (room temperature). Although data were taken across this temperature range, we encountered difficulties stabilizing the temperature at several specific points such as at 120, 250, and 260 K. These points were therefore excluded from the analysis to avoid introducing uncertainties. Additionally, due to the limitations of the present setup, complete elimination of heat from the readout board was not achievable, resulting in a minimum temperature of 86 K, which is above the aimed temperature of 77 K.

We characterized the scintillation of an undoped CsI crystal using a 109Cd{}^{109}\mathrm{Cd} source that emits 22.1 keV and 25.0 keV x-rays as well as an 88.0 keV γ\gamma-rays. Because of the energy resolution, the 22.1 keV and 25.0 keV x-ray peaks overlapped and were roughly adjusted to around 23.0 keV, as shown in Figure 3. Energy calibrations were performed using the 88.0 keV position. At low temperatures, the 23.0 keV peak is utilized after confirming the linearity of the two peaks. This decision is due to the saturation of the signal corresponding to the energy of the 88.0 keV peak in our electronics, caused by increasing gain at low temperatures.

Figure 3. Energy spectrum of the 109Cd{}^{109}\mathrm{Cd} calibration source, measured at 150 K with ΔV=5\Delta V = 5 V. The red triangles mark the two energy peaks at 23.0 keV and 88.0 keV.

Dark count rate & Crosstalk

Two critical factors in understanding SiPM data are the dark count rate (DCR) and crosstalk. We measured the DCR and crosstalk using a 1.6 μ\mus time window located prior to the event-triggered position in the recorded signal data. This time window, referred to as the pedestal region, is chosen to exclude the influence of the scintillation event and SiPM after-pulses.

The DCR is a significant noise source, particularly at room temperature, while it decreases significantly at lower temperatures [26, 25, 46].

The rate is calculated by dividing the number of clusters, which are isolated pulse typically equivalent to single photoelectrons, identified in the pedestal regions by the corresponding time interval from the offline analysis. Since the DCR depends on both temperature and bias voltage, we assessed the DCR by varying temperature and overvoltage, as shown in Figure 4. The DCR increases with higher overvoltage and exhibits a dramatic decrease at lower temperatures. For instance, at room temperature, the DCR is about 700 kHz with ΔV=5\Delta V = 5 V and decreased to 0.2 kHz at 150 K. Below 150 K, the DCR drops further, resulting in poor statistical reliability, therefore, data in this region were not included in the analysis.

Figure 4. Dark count rate as a function of temperature for three different overvoltages.

Crosstalk refers to the probability that a secondary photon, emitted during the avalanche generation process in one pixel following a true photon hit, triggers another pixel, resulting in multiple photoelectron events. Crosstalk can be categorized into internal Crosstalk (iCT) and external Crosstalk (eCT), depending on where the secondary avalanche occurs. iCT occurs when the secondary avalanche happens in a nearby pixel within the same SiPM, while eCT occurs when the emitted luminescence escapes from the SiPM and fires another SiPM at a distance [24]. Crosstalk is independent of temperature variation but highly dependent on bias voltage [25, 26]. Both iCT and eCT probabilities were measured at room temperature.

The iCT probability is estimated from the charge distribution of DCR, as shown in Figure 3 of Ref. [25]. We can easily identify single-photoelectron and multi-photoelectron events to evaluate the crosstalk probability as the ratio of the number of charge-weighted multi-photoelectrons to single-photoelectrons. This measurement was first performed with a single SiPM turned on. Then, the same measurement was repeated with both SiPMs turned on. In this case, a higher crosstalk probability was observed compared to the single SiPM measurement, indicating the presence of eCT due to the secondary avalanche in the adjacent SiPM. The ratio between these two probabilities is used to estimate eCT. Table 1 summarizes the measured crosstalk probabilities at different overvoltages, averaged over the two SiPMs. Due to the increasing gain of the SiPM with higher overvoltages, the crosstalk probability also rises.

Overvoltage (V)iCT (%)eCT (%)
311.9 ± 0.37.6 ± 0.4
413.9 ± 0.38.8 ± 0.2
527.3 ± 0.38.1 ± 0.2
654.5 ± 0.410.6 ± 0.2
771.2 ± 2.214.2 ± 0.3
890.8 ± 7.833.6 ± 0.3

Table 1. Crosstalk probability of SiPM measured at different overvoltages at room temperature. iCT and eCT represent internal and external crosstalk respectively.

Light yield & Energy resolution

The light yield of the undoped CsI crystal was measured using the 109Cd^{109}\mathrm{Cd} source for temperatures ranging from 86 K to 293 K. To maintain a consistent gain across different temperatures, overvoltage was kept constant. The results, shown in Figure 5, are presented alongside previous measurements using typical PMTs [16, 17], with all three datasets normalized to have the same value at 280 K. We show data at 5 V overvoltage for the temperature-dependent analysis, as measurements at higher overvoltages become less reliable due to increased crosstalk and DCR at elevated temperatures. The observed increase in light yield at lower temperatures aligns with earlier measurements. At 86 K, the total light yields for overvoltages of 3 V and 5 V are 21.3 ± 0.8 and 22.9 ± 0.8 PE/keV, respectively. The highest yield of 26.2 ± 1.3 PE/keV was obtained at the same temperature with overvoltages of 8 V, corresponding to the voltage with the highest gain. The contributions from DCR and crosstalk are considered in the light yield estimation and the errors associated with these values are included as systematic uncertainties. The light yield is calculated as the charge integrated in the analysis time window divided by the charge of a single photoelectron (SPE) and the energy of the peak from the radioactive source. Any charge contributed by the DCR should be subtracted from the total charge only to account charges from scintillation events. Additionally, the crosstalk probability should be corrected to account effective charge produced by single-photoelectron. This process can be described as following,

Figure 5. The relative light yield of CsI, normalized to have same value at 280 K, is depicted as a temperature-dependent function. The data are presented for ΔV=5\Delta V = 5 V (blue filled circles), with a value of 0.88 ± 0.02 PE/keV at 280 K. Additionally, for comparison, two previous measurements conducted using PMT are overlaid in green open triangle [16] and red open square [17]. The overall trend aligns with the results from other measurements.

LightYield=QTot−QDCRqSPE⋅(1+piCT)⋅(1+peCT)⋅1Ecal,(1)LightYield = \frac{Q_{Tot} - Q_{DCR}}{q_{SPE} \cdot(1 + p_{iCT}) \cdot(1 + p_{eCT})} \cdot\frac{1}{E_{cal}}, \tag*{(1)}
QDCR=(qSPE⋅DCR⋅T),Q_{DCR} = (q_{SPE} \cdot\mathrm{DCR} \cdot T),

where QTotQ_{Tot} is the total charge within the timing window of this analysis (denoted as TT), which is 16 μ\mus, qSPEq_{SPE} denotes the charge of SPE, and piCTp_{iCT} (peCTp_{eCT}) indicates the internal (external) crosstalk probability of the SiPM as summarized in Table 1. EcalE_{cal} represents the energy from the 109Cd^{109}\mathrm{Cd} source, either 23.0 or 88.0 keV.

The emission wavelength of the undoped CsI crystal is peaked at 310 nm at room temperature and measured to be temperature dependent and equal to 340 nm at 77 K [47]. At this wavelength, SiPMs have an almost twice higher PDE of roughly 30% than that of typical PMTs, which have a PDE of less than 15%. This results in an increased light yield compared to PMT measurements [48]. Similar results were reported by other groups [24], achieving a light yield of 30.1 PE/keV at 77 K with SiPMs coupled to undoped CsI crystals and a wavelength shifter from 340 nm to 420 nm.

We estimated the standard deviation of the mixed 23.0 keV peak with a Gaussian fit to evaluate the resolution, calculated as the standard deviation divided by energy. As shown in Figure 6, the improved resolution at low temperatures demonstrates the enhancement of light output.

Energy resolution versus temperature

Figure 6. Energy resolution (Standard deviation/Energy) of 23.0 keV mixed peak from 22.1 keV and 25.0 keV x-rays of the 109Cd{}^{109}\mathrm{Cd} source at different temperatures with ΔV=5\Delta V = 5 V.

Decay time

We investigated the temperature-dependent variation of the scintillation decay time of the undoped CsI crystal with overvoltage of 5 V for SiPM. The accumulated waveforms at each temperature were fitted with a single exponential function.

f(t)=Aexp⁡(−(t−t0)/τ),(2)f(t) = A\exp(-(t-t_0)/\tau), \tag*{(2)}

where τ\tau is the decay constant. AA and t0t_0 represent the normalization factor and the rising edge position of the scintillation, respectively.

The waveforms and fitted results for the four selected temperatures, presented in Figure 7, revealed an undesired undershoot in the signal generated by our SiPM readout electronics. The undershoot varied from event to event and appeared to be influenced by both the signal amplitude and baseline fluctuations, likely due to non-idealities in the readout system. Given the uncertainty in applying a reliable, event-independent correction model, we instead limited the waveform fitting to a short time window and applied a single exponential to avoid misestimating the decay time due to the undershoot, even though previous PMT measurements indicate the presence of two decay components[16, 17].

Figure 7. Accumulated waveforms of the peak from 109Cd{}^{109}\mathrm{Cd} with ΔV=5\Delta V = 5 V are shown at temperatures of 293 K, 200 K, 150 K, and 86 K, depicted in panels (a) to (d). The red dashed line represents the fitted exponential function, and the decay constant is described in each plot.

The temperature-dependent decay time of the undoped CsI crystal is shown in Figure 8 and compared with previous PMT measurements[16, 17]. Our measurements demonstrate a well-agreed trend of increased decay time at low temperatures. Slightly faster decay times in our measurements at all temperatures result from evaluating the decay time within a short time range, to exclude the severe undershoot previously described. The measured decay time is 76.0 ± 6.0 ns at room temperature and 605.2 ± 3.2 ns at 86 K. Generally, a longer decay time is advantageous for identifying nuclear recoil events using pulse shape discrimination (PSD). We plan to test PSD capability with a neutron source at liquid nitrogen temperatures in the future.

Figure 8. Decay time of a pure CsI crystal as a function of temperature with ΔV=5\Delta V = 5 V (blue filled circles). Two previous measurements (green open triangle [16] and red open squares [17]) using PMTs are overlaid for comparison

200 kg undoped CsI crystals for the dark matter search

Following up on the high light yield of the undoped CsI crystal at liquid nitrogen temperature, we consider future dark matter search experiments with 200 kg of undoped CsI crystals coupled with SiPM arrays, especially to search for low-mass dark matter with spin-dependent interactions. Both cesium and iodine have non-zero proton spin due to their odd proton numbers, providing an advantage for searching for WIMP-proton spin-dependent interactions.

The low-background CsI crystal growth technique was successfully developed for the KIMS CsI(Tl) dark matter search experiments [27, 49]. The primary sources of internal background in CsI crystals were identified as 137Cs{}^{137}\mathrm{Cs} and 87Rb{}^{87}\mathrm{Rb}. The presence of 137Cs{}^{137}\mathrm{Cs} is mainly attributed to water used in the chemical process of cesium extraction. By employing purified water, the contamination of 137Cs{}^{137}\mathrm{Cs} can be reduced by one order of magnitude in the CsI powder [28]. The 87Rb{}^{87}\mathrm{Rb} nuclei are extracted using the recrystallization method, taking advantage of the different solubility of RbI and CsI in water [49]. About 400 kg of remnant CsI powder, left over from the KIMS CsI(Tl) crystal growth process, has been stored at the Yangyang underground laboratory for 20 years. This reserve can be effectively utilized to grow 200 kg of undoped CsI crystals for future experiments. Additionally, a powder purification facility based on the recrystallization process was developed for NaI powder [33, 34, 35]. This facility can be re-adapted for CsI powder purification, providing a streamlined process for obtaining low background levels in the CsI crystals if required.

Low-background crystal growth can be conducted at the Institute for Basic Science in Korea, where crystal growers have been developed for low-background NaI(Tl) crystals. The Kyropulous growers designed for NaI(Tl) crystals can be readily adapted for undoped CsI crystal growth. Additionally, Bridgman growers, commonly used for CsI crystal growth, are available for this purpose. In the KIMS experiment, the lowest background achieved at 2 keV was about 2.5 counts/kg/keV/day with the latest crystal delivered from Beijing Hamamatsu [50]. The radioactive background in the PMTs and the direct attachment of PMTs to the crystal contribute to external background at low energy, estimated to be approximately 0.5–1 counts/kg/keV/day [29]. Replacing the PMTs with SiPM arrays significantly reduces the external background contribution. Indeed, the contributions from 134Cs{}^{134}\mathrm{Cs}, estimated at the level of 1.0 count/kg/keV/day, can be considered negligible if crystals are grown using 20 years of underground-stored powder. This is attributed to the relatively short half-life of 134Cs{}^{134}\mathrm{Cs}, which is only 2.1 years. By leveraging existing powder and employing low-background crystal growing technology, the combination of undoped CsI crystals with SiPM arrays has the potential to achieve a background level of less than 1 count/kg/keV/day.

We are using a conservative estimate of 26.2 PE/keV for light yields with the SiPM arrays, even though there is an

around 10% increase in light output at 77 K compared to 86 K. In the low-energy data acquisition setup, where two SiPM arrays are attached to two ends of the crystal, we can impose a requirement for coincident photoelectrons in the two SiPM arrays to minimize noise triggering while achieving the minimum thresholds, corresponding to an energy threshold of roughly 0.08 keV. In contrast to PMT measurements, where PMT-induced noise from Cherenkov radiation of charged particles passing through quartz or glass materials can dominate low-energy events and increase the analysis threshold [51], such noise is less frequent in SiPM arrays since quartz or glass materials can be minimized in their construction. While DCR could be a potential concern, they are sufficiently low at 77 K. For the purpose of calculating dark matter detection sensitivities, we assume a 5 PE threshold, consistent with CsI(Na) measurements using PMT readout [7].

The proposed 200 kg undoped CsI experiment can be implemented using a 5×55 \times5 array of 8.7 kg CsI modules, each with dimensions of 8 cm×8 cm×30 cm8\ \mathrm{cm} \times8\ \mathrm{cm} \times30\ \mathrm{cm} (similar to the size used in the KIMS experiment [31, 32]). The two ends of the 8 cm ×\times 8 cm side can be covered with 13×1313 \times13 SiPM arrays with 6 mm×6 mm6\ \mathrm{mm} \times6\ \mathrm{mm} cells. The assumed parameters for the analysis include a flat background of 1 count/kg/keV/day, a light yield of 26.2 PE/keV, corresponding to 0.08 keV, and an analysis threshold of 5 PE. Additionally, an increased light yield of 30 PE/keV, achieved through the application of a wavelength shifter [24], corresponding to a 0.07 keV threshold, is considered in the evaluation. For the benchmark model of the low-mass dark matter search, low-energy signals via Migdal electrons [52, 53] induced by WIMP–proton spin-dependent interaction are assessed.

To estimate the dark matter signal enhancement that is provided by the Migdal effect, we generate expected signals by multiplying the nuclear recoil rate of WIMP interactions [54] and ionization probability of the Migdal effect [53, 51]. For various WIMP masses and WIMP-proton spin-dependent interactions, we simulate the expected event rates in the specific context of the standard halo model [55, 56]. Responses that include form factors and proton spin values of the nuclei are implemented from the publicly available DMD package [57, 58]. Due to the absence of calculations for cesium, we utilized the ionization probability from iodine. Additionally, we experimented with xenon’s ionization probability to cross check the results. The ionization probabilities from elements with similar atomic mass numbers to cesium yielded comparable results. Assuming a one-year data exposure with 200 kg of undoped CsI crystals, the Poisson fluctuation of the measured number of photoelectrons is taken into account for the detector resolution, as discussed in Ref. [59]. The nuclear recoil quenching factors (QFs) which is the ratio of the scintillation light yield from cesium or iodine recoil relative to that from electron recoil for the same energy are additionally considered. The measured quenching factor of undoped CsI from Ref. [60] is incorporated into the calculations. In this calculation, detection efficiency and systematics are not considered.

We use an ensemble of simulated experiments to estimate the sensitivity of the experiment. This ensemble test quantifies the expected cross-section limits for WIMP-proton spin-dependent interactions with the Migdal effect. For each experiment, we determine a simulated spectrum based on a background-only hypothesis, with the assumed background achieved through Gaussian fluctuations. The simulated data is then fitted using a signal and background hypothesis. The fit is performed within the energy range of 5 PE to 400 PE for each WIMP model with various masses, employing the Bayesian approach used in the COSINE-100 experiment [10]. The 1σ1\sigma and 2σ2\sigma standard-deviation probability regions of the expected 90% confidence level limits are calculated from 1000 simulated experiments.

The limits on the WIMP-proton spin-dependent interaction with the Migdal effect shown in Figure 9 are compared with the current best limits on the low-mass WIMP searches from XENON1T with Migdal[61], CRESST-III LiAlO2_2 [6], Collar [62], CDMSlite [63], PICO-60 [64], and PICASSO [65]. Taking advantage of odd-proton numbers and low-energy threshold, the projected sensitivity with 200 kg of undoped CsI experiment can reach the world’s best sensitivities for WIMP masses between 60 MeV/c2c^2 and 2 GeV/c2c^2.

Figure 9. The expected 90% confidence level limits for the undoped CsI with a 200 kg, 1-year exposure using the Migdal effect on the WIMP-proton spin-dependent cross-section are presented, assuming the background-only hypothesis. In addition to the nominal assumed light yield of 26.2 PE/keV (black solid line with 1σ1\sigma (green) and 2σ2\sigma (yellow) systematic bands), higher light yields, assuming the application of the wavelength shifter of 30 PE/keV (red dashed line), are evaluated. These limits are compared with the current best limits from XENON1T (Migdal)[61], CRESST-III LiAlO2_2 [6], Collar[62], CDMSlite [63], PICO-60 [64], and PICASSO [65].

Conclusion

The characteristics of a pure CsI crystal coupled with two SiPMs were investigated at temperatures ranging from 86 K to room temperature. The increased light yield and decay time at low temperatures were observed consistently with the literature. We obtained a light yield of 26.2 ±\pm 1.3 PE/keV at 86 K, which is 12 times larger than the light yield at room temperature. Given our capacity for producing low-background undoped CsI crystals, we investigated the expected sensitivity of a 200 kg undoped CsI experiment operating at 77 K with a 1-year exposure, 1 count/kg/keV/day background rate, and a 5 PE energy threshold. In this scenario, the undoped CsI crystal can explore low-mass dark matter between 60 MeV/c2c^2 and 2 GeV/c2c^2 with the world’s best sensitivities for WIMP-proton spin-dependent interactions.

Acknowledgements

This work was supported by the Institute for Basic Science (IBS) under project code IBS-R016-A1.

References

  1. [1]S. Kim, H. Kim, Y. Kim, Scintillator-based detectors for dark matter searches i, New J. Phys. 12 (2010) 075003.DOI
  2. [2]J. Amare, et al., Performance of ANAIS-112 experiment after the first year of data taking, Eur. Phys. J. C 79 (3) (2019) 228. arXiv:1812.01472, doi:10.1140/epjc/s10052-019-6696-4.DOI
  3. [3]R. Bernabei, et al., First model independent results from DAMA/LIBRA-phase2, Nucl. Phys. Atom. Energy 19 (4) (2018) 307–325. doi:10.15407/jnpae2018.04.307.DOI
  4. [4]G. Adhikari, et al., Search for a dark matter-induced annual modulation signal in NaI(Tl) with the COSINE-100 experiment, Phys. Rev. Lett. 123 (2019) 031302. arXiv:1903.10098, doi:10.1103/PhysRevLett.123.031302.
  5. [5]A. Zani, et al., The ASTAROTH Project: enhanced low-energy sensitivity to Dark Matter annual modulation, J. Phys. Conf. Ser. 2156 (2021) 012060. doi:10.1088/1742-6596/2156/1/012060.DOI
  6. [6]G. Angloher, et al., Testing spin-dependent dark matter interactions with lithium aluminate targets in CRESST-III, Phys. Rev. D 106 (9) (2022) 092008. arXiv:2207.07640, doi:10.1103/PhysRevD.106.092008.DOI
  7. [7]D. Akimov, et al., Observation of Coherent Elastic Neutrino-Nucleus Scattering, Science 357 (6356) (2017) 1123. arXiv:1708.01294, doi:10.1126/science.aao0990.DOI
  8. [8]J. J. Choi, et al., Exploring coherent elastic neutrino-nucleus scattering using reactor electron antineutrinos in the NEON experiment, Eur. Phys. J. C 83 (3) (2023) 226. arXiv:2204.06318, doi:10.1140/epjc/s10052-023-11352-x.DOI
  9. [9]K. W. Kim, et al., Limits on Interactions Between Weakly Interacting Massive Particles and Nucleons Obtained with NaI(Tl) crystal Detectors, JHEP 03 (2019) 194. arXiv:1806.06499, doi:10.1007/JHEP03(2019)194.DOI
  10. [10]G. Adhikari, et al., Strong constraints from COSINE-100 on DAMA dark matter results using the same sodium iodide target, Sci. Adv. 7 (46) (2021) eabk2699. doi:10.1126/sciadv.abk2699.DOI
  11. [11]G. Adhikari, et al., Three-year annual modulation search with COSINE-100, Phys. Rev. D 106 (5) (2022) 052005. doi:10.1103/PhysRevD.106.052005.DOI
  12. [12]J. Amare, et al., Annual Modulation Results from Three Years Exposure of ANAIS-112, Phys. Rev. D 103 (10) (2021) 102005. arXiv:2103.01175, doi:10.1103/PhysRevD.103.102005.DOI
  13. [13]M. Antonello, et al., The SABRE project and the SABRE Proof-of-Principle, Eur. Phys. J. C 79 (4) (2019) 363. arXiv:1806.09340, doi:10.1140/epjc/s10052-019-6860-y.DOI
  14. [14]R. Bernabei, et al., The DAMA project: Achievements, implications and perspectives, Prog. Part. Nucl. Phys. 114 (2020) 103810. doi:10.1016/j.ppnp.2020.103810.
  15. [15]J. J. Choi, B. J. Park, C. Ha, K. W. Kim, S. K. Kim, Y. D. Kim, Y. J. Ko, H. S. Lee, S. H. Lee, S. L. Olsen, Improving the light collection using a new NaI(Tl) crystal encapsulation, Nucl. Instrum. Meth. A 981 (2020) 164556. arXiv:2006.02573, doi:10.1016/j.nima.2020.164556.DOI
  16. [16]C. Amsler, D. Gröger, W. Joffrain, D. Lindelöf, M. Marchesotti, P. Niederberger, H. Pruys, C. Regenfus, P. Riedler, A. Rotondi, Temperature dependence of pure CsI: Scintillation light yield and decay time, Nucl. Instrum. Meth. A 480 (2) (2002) 494–500. doi:10.1016/S0168-9002(01)01239-6.DOI
  17. [17]S. Park, A. Khan, H. Kim, Characterization of a Pure CsI Crystal at Low Temperature for a Dark-Matter Search, New Physics: Sae Mulli 71 (5) (2021) 469–475. doi:10.3938/NPSM.71.469.DOI
  18. [18]H. Nishimura, M. Nakata, T. Tsujimoto, M. Nakayama, Origin of the 4.1-eV luminescence in pure CsI scintillator, Phys. Rev. B 51 (4) (1995) 2167–2172. doi:10.1103/PhysRevB.51.2167.DOI
  19. [19]P. Schotanus, R. Kamermans, Scintillation characteristics of pure and Tl-doped CsI crystals, IEEE Tran. Nucl. Sci. 37 (2) (1990) 177–182. doi:10.1109/23.106614.DOI
  20. [20]M. Moszynski, M. Balcerzyk, W. Czarnacki, M. Kapusta, W. Klamra, P. Schotanus, A. Synfeldt, M. Szawlowski, Study of pure nai at room and liquid nitrogen temperatures, IEEE Transactions on Nuclear Science 50 (4) (2003) 767–773. doi:10.1109/TNS.2003.815176.DOI
  21. [21]F. Reindl, et al., Results of the first NaI scintillating calorimeter prototypes by COSINUS, J. Phys. Conf. Ser. 1342 (1) (2020) 012099. arXiv:1711.01482, doi:10.1088/1742-6596/1342/1/012099.DOI
  22. [22]D. Poda, Scintillation in Low-Temperature Particle Detectors, MDPI Physics 3 (3) (2021) 473–535. doi:10.3390/physics3030032.DOI
  23. [23]K. Ding, J. Liu, Y. Yang, D. Chernyak, First operation of undoped CsI directly coupled with SiPMs at 77 K, Eur. Phys. J. C 82 (4) (2022) 344. arXiv:2201.00483, doi:10.1140/epjc/s10052-022-10289-x.DOI
  24. [24]L. Wang, et al., Reactor neutrino physics potentials of cryogenic pure-CsI crystal, Eur. Phys. J. C 84 (4) (2024) 440. arXiv:2212.11515, doi:10.1140/epjc/s10052-024-12800-y.DOI
  25. [25]H. Y. Lee, J. A. Jeon, K. W. Kim, W. K. Kim, H. S. Lee, M. H. Lee, Scintillation characteristics of a NaI(Tl) crystal at low-temperature with silicon photomultiplier, JINST 17 (02) (2022) P02027. doi:10.1088/1748-0221/17/02/P02027.DOI
  26. [26]P. K. Lightfoot, G. J. Barker, K. Mavrokoridis, Y. A. Ramachers, N. J. C. Spooner, Characterisation of a silicon photomultiplier device for applications in liquid argon based neutrino physics and dark matter searches, JINST 3 (2008) P10001. arXiv:0807.3220, doi:10.1088/1748-0221/3/10/P10001.DOI
  27. [27]T. Y. Kim, et al., Study of the internal background of CsI(Tl) crystal detectors for dark matter search, Nucl. Instrum. Meth. A 500 (2003) 337–344. doi:10.1016/S0168-9002(03)00346-2.DOI
  28. [28]Y. D. Kim, et al., Inhibition of Cs-137 contamination in cesium iodide, Nucl. Instrum. Meth. A 552 (2005) 456–462. doi:10.1016/j.nima.2005.06.080.DOI
  29. [29]H. S. Lee, et al., Development of low-background CsI(Tl) crystals for WIMP search, Nucl. Instrum. Meth. A 571 (2007) 644–650. doi:10.1016/j.nima.2006.10.325.DOI
  30. [30]H. S. Lee, et al., First limit on WIMP cross section with low background CsI(Tl) crystal detector, Phys. Lett. B 633 (2006) 201–208. arXiv:astro-ph/0509080, doi:10.1016/j.physletb.2005.12.035.DOI
  31. [31]H. S. Lee, et al., Limits on WIMP-nucleon cross section with CsI(Tl) crystal detectors, Phys. Rev. Lett. 99 (2007) 091301. arXiv:0704.0423, doi:10.1103/PhysRevLett.99.091301.DOI
  32. [32]S. C. Kim, et al., New Limits on Interactions between Weakly Interacting Massive Particles and Nucleons Obtained with CsI(Tl) Crystal Detectors, Phys. Rev. Lett. 108 (2012) 181301. doi:10.1103/PhysRevLett.108.181301.DOI
  33. [33]K. Shin, O. Gileva, Y. Kim, H. S. Lee, H. Park, Reduction of the radioactivity in sodium iodide (NaI) powder by recrystallization method, J. Radioanal. Nucl. Chem. 317 (3) (2018) 1329–1332. doi:10.1007/s10967-018-6006-y.DOI
  34. [34]K. Shin, J. Choe, O. Gileva, A. Iltis, Y. Kim, C. Lee, H. S. Lee, M. H. Lee, H. K. Park, A facility for mass production of ultra-pure NaI powder for the COSINE-200 experiment, JINST 15 (07) (2020) C07031. arXiv:2004.13280, doi:10.1088/1748-0221/15/07/C07031.DOI
  35. [35]K. Shin, J. Choe, O. Gileva, A. Iltis, Y. Kim, Y. Kim, C. Lee, E. Lee, H. Lee, M. H. Lee, Mass production of ultra-pure NaI powder for COSINE-200, Front. in Phys. 11 (2023) 1142849. arXiv:2301.05400, doi:10.3389/fphy.2023.1142849.DOI
  36. [36]S. Ra, et al., Scintillation crystal growth at the CUP, PoS ICHEP2018 (2019) 668. doi:10.22323/1.340.0668.
  37. [37]B. J. Park, et al., Development of ultra-pure NaI(Tl) detectors for the COSINE-200 experiment, Eur. Phys. J. C 80 (9) (2020) 814. arXiv:2004.06287, doi:10.1140/epjc/s10052-020-8386-8.DOI
  38. [38]H. Lee, et al., Performance of an ultra-pure NaI(Tl) detector produced by an indigenously-developed purification method and crystal growth for the COSINE-200 experiment, Front. in Phys. 11 (2023) 1142765. arXiv:2301.04884, doi:10.3389/fphy.2023.1142765.DOI
  39. [39]A. Ferri, F. Acerbi, A. Gola, G. Paternoster, C. Piemonte, N. Zorzi, A comprehensive study of temperature stability of Silicon PhotoMultiplier, Journal of Instrumentation 9 (06) (2014) P06018. doi:10.1088/1748-0221/9/06/P06018.DOI
  40. [40]T. Teranishi, Y. Ueno, M. Osada, S. Oka, K. Iribe, H. Yoshida, H. Sakai, T. Kubo, Pulse shape analysis of signals from SiPM-based CsI(Tl) detectors for low-energy protons: Saturation correction and particle identification, Nucl. Instrum. Meth. A 989 (2021) 164967. doi:10.1016/j.nima.2020.164967.DOI
  41. [41]S. M. Sze, G. Gibbons, Avalanche breakdown voltages of abrupt and linearly graded p-n junctions in Ge, Si, GaAs, and GaP, Appl. Phys. Lett. 8 (5) (1966) 111–113. doi:10.1063/1.1754511.DOI
  42. [42]N. Dinu, A. Nagai, A. Para, Breakdown voltage and triggering probability of SiPM from IV curves at different temperatures, Nucl. Instrum. Meth. A 845 (2017) 64–68. doi:10.1016/j.nima.2016.05.110.DOI
  43. [43]A. Nepomuk Otte, D. Garcia, T. Nguyen, D. Puroshotham, Characterization of Three High Efficiency and Blue Sensitive Silicon Photomultipliers, Nucl. Instrum. Meth. A 846 (2017) 106–125. arXiv:1606.05186, doi:10.1016/j.nima.2016.09.053.DOI
  44. [44]N. Dinu, A. Nagai, A. Para, Studies of MPPC detectors down to cryogenic temperatures, Nucl. Instrum. Meth. A 787 (2015) 275–279. doi:10.1016/j.nima.2014.12.061.
  45. [45]G. Collazuol, M. G. Bisogni, S. Marcatili, C. Piemonte, A. Del Guerra, Studies of silicon photomultipliers at cryogenic temperatures, Nucl. Instrum. Meth. A 628 (1) (2011) 389–392. doi:10.1016/j.nima.2010.07.008.DOI
  46. [46]A. Vacheret, et al., Characterization and Simulation of the Response of Multi Pixel Photon Counters to Low Light Levels, Nucl. Instrum. Meth. A 656 (1) (2011) 69–83. arXiv:1101.1996, doi:10.1016/j.nima.2011.07.022.DOI
  47. [47]C. L. Woody, P. W. Levy, J. A. Kierstead, T. Skwarnicki, Z. Sobolewski, M. Goldberg, N. Horwitz, P. Souder, D. F. Anderson, Readout techniques and radiation damage of undoped cesium iodide, IEEE Trans. Nucl. Sci. 37 (1990) 492–499. doi:10.1109/23.106667.DOI
  48. [48]K. Ding, D. Chernyak, J. Liu, Light yield of cold undoped CsI crystal down to 13 keV and the application of such crystals in neutrino detection, Eur. Phys. J. C 80 (12) (2020) 1146. arXiv:2008.00939, doi:10.1140/epjc/s10052-020-08712-2.
  49. [49]H. S. Lee, Dark Matter Search with CsI(Tl) Crystals, Ph.d dissertation, Seoul National University (2007).
  50. [50]S. C. Kim, Dark Matter Search with 100kg of CsI(Tl) Crystals, Ph.d dissertation, Seoul National University (2011).
  51. [51]G. Adhikari, et al., Lowering the energy threshold in COSINE-100 dark matter searches, Astropart. Phys. 130 (2021) 102581. arXiv:2005.13784, doi:10.1016/j.astropartphys.2021.102581.DOI
  52. [52]A. Migdal, Ionization of atoms accompanying α- and β-decay., J. Phys. USSR 4 (1941) 449.
  53. [53]M. Ibe, W. Nakano, Y. Shoji, K. Suzuki, Migdal Effect in Dark Matter Direct Detection Experiments, JHEP 03 (2018) 194. arXiv:1707.07258, doi:10.1007/JHEP03(2018)194.DOI
  54. [54]C. Savage, G. Gelmini, P. Gondolo, K. Freese, Compatibility of DAMA/LIBRA dark matter detection with other searches, JCAP 0904 (2009) 010. doi:10.1088/1475-7516/2009/04/010.DOI
  55. [55]J. Lewin, P. Smith, Review of mathematics, numerical factors, and corrections for dark matter experiments based on elastic nuclear recoil, Astropart. Phys. 6 (1996) 87. doi:10.1016/S0927-6505(96)00047-3.DOI
  56. [56]K. Freese, M. Lisanti, C. Savage, Colloquium: Annual modulation of dark matter, Rev. Mod. Phys. 85 (2013) 1561–1581. doi:10.1103/RevModPhys.85.1561. URL https://link.aps.org/doi/10.1103/RevModPhys.85.1561DOI
  57. [57]V. Gluscevic, S. D. McDermott, dmdd: Dark matter direct detection, Astrophysics Source Code Library [ascl:1506.002] (2015).
  58. [58]V. Gluscevic, M. I. Gresham, S. D. McDermott, A. H. G. Peter, K. M. Zurek, Identifying the Theory of Dark Matter with Direct Detection, JCAP 12 (2015) 057. arXiv:1506.04454, doi:10.1088/1475-7516/2015/12/057.DOI
  59. [59]Y. J. Ko, H. S. Lee, Sensitivities for coherent elastic scattering of solar and supernova neutrinos with future NaI(Tl) dark matter search detectors of COSINE-200/1T, Astropart. Phys. 153 (2023) 102890. arXiv:2210.01386, doi:10.1016/j.astropartphys.2023.102890.DOI
  60. [60]C. M. Lewis, J. I. Collar, Response of undoped cryogenic CsI to low-energy nuclear recoils, Phys. Rev. C 104 (1) (2021) 014612. arXiv:2101.03264, doi:10.1103/PhysRevC.104.014612.DOI
  61. [61]E. A. et al., Search for Light Dark Matter Interactions Enhanced by the Migdal Effect or Bremsstrahlung in XENON1T, Phys. Rev. Lett. 123 (24) (2019) 241803. doi:10.1103/PhysRevLett.123.241803.DOI
  62. [62]J. I. Collar, Search for a nonrelativistic component in the spectrum of cosmic rays at Earth, Phys. Rev. D 98 (2) (2018) 023005. doi:10.1103/PhysRevD.98.023005.DOI
  63. [63]R. A. et al., Low-mass dark matter search with CDMSlite, Phys. Rev. D 97 (2) (2018) 022002. doi:10.1103/PhysRevD.97.022002.DOI
  64. [64]C. A. et al., Dark matter search results from the complete exposure of the PICOLON 60 C3F8 bubble chamber, Phys. Rev. D 100 (2) (2019) 022001. doi:10.1103/PhysRevD.100.022001.DOI
  65. [65]E. B. et al., Final results of the PICASSO dark matter search experiment, Astropart. Phys. 90 (2017) 85–92. doi:10.1016/j.astropartphys.2017.02.005.DOI

Paper details

vlnc:W_7j5c4rm6
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents