WorksComputer Science
Integrating Material Selection with Design Optimization via Neural Networks
Abstract
The engineering design process often entails optimizing the underlying geometry while simultaneously selecting a suitable material. For a certain class of simple problems, the two are separable where, for example, one can first select an optimal material, and then optimize the geometry. However, in general, the two are not separable. Furthermore, the discrete nature of material selection is not compatible with gradient-based geometry optimization, making simultaneous optimization challenging. In this paper, we propose the use of variational autoencoders (VAE) for simultaneous optimization. First, a data-driven VAE is used to project the discrete material database onto a continuous and differentiable latent space. This is then coupled with a fully-connected neural network, embedded with a finite-element solver, to simultaneously optimize the material and geometry. The neural-network's built-in gradient optimizer and back-propagation are exploited during optimization. The proposed framework is demonstrated using trusses, where an optimal material needs to be chosen from a database, while simultaneously optimizing the cross-sectional areas of the truss members. Several numerical examples illustrate the efficacy of the proposed framework. The Python code used in these experiments is available at github.com/UW-ERSL/MaTruss
Introduction
In engineering design, we are often faced with the task of optimizing the underlying geometry and selecting an optimal material [1]. As a simple example, consider the truss design problem illustrated in Figure 1 where one must optimize the cross-sectional areas, while selecting, for simplicity, a single material for all the truss members. Formally, one can pose this as [2, 3]:

Figure 1. A truss design problem involving optimizing the cross-sectional areas of truss members, and selecting an optimal material.
where is the objective (for example, compliance), denotes a set of constraints (such as yield stress and buckling), is the applied force, is the truss stiffness matrix, and is the nodal displacements. The design variables are the cross-sectional areas of the members , with limits and , and the material choice . We denote the collection of relevant material properties by ; these may include, for example, the Young’s modulus , cost per unit mass , mass density and yield strength .
Literature Review
Observe that the two sets of design variables are tightly coupled. In other words, one cannot, for example, pick a material, and then optimize the cross-sectional areas (or, vice-versa). To quote [4] "... either approach does not guarantee the optimal combination of geometry and material". Furthermore, while the cross-sectional areas are continuously varying, the material choice is discrete, making the problem difficult to solve using classic gradient-based optimization.
If the geometry is fixed, Ashby’s method [5] that relies on a performance metric, is the most popular strategy for material selection. Furthermore, for simple design problems where the loads, geometry and material functions are separable [6], a material index can be used to select the best material. This is simple, efficient and reliable. However, when there are multiple objectives or constraints, a weighted approach is recommended [7]. In practice, computing these weights is not trivial, and the material choice may be far from optimal. Several non-gradient methods have been proposed for material selection [8, 9, 10], but these cannot be integrated with gradient-based optimization.
An alternate concept of a design index was proposed in Ananthasuresh and Ashby [11]. It was shown that the design index can be used to construct a smooth material function, enabling simultaneous optimization of the geometry and selection of the material via gradient based optimization [4]. However, design indices were limited to simple determinate trusses. In [12], for the special case of a single stress constraint and a single load, the authors concluded that utmost two materials are sufficient and that the truss design problem can be cast as a linear programming problem. Unfortunately, this method does not apply when there are multiple constraints. Recently, the authors of [13] considered two materials (glue-laminated timber and steel) to design truss structures incorporating stress constraints as a mixed-integer quadratic problem (MIQPs). However the authors note that "[MIQPs]... require algorithmic tuning and considerable computational power". Another hybrid approach was proposed in [14] where a combination of the gradient-based methods such as sequential quadratic programming (SQP) and an evolution method such as genetic algorithm (GA) are used to solve MDNLPs. But these methods can be prohibitively expensive.
Mathematically, the problem of (discrete) material selection and (continuous) area optimization can be cast as mixed-discrete nonlinear programming problems (MDNLPs). Such problems are fairly common in engineering, and several solution strategies methods have been proposed; see [15, 16, 17]. However, regardless of the strategy, these methods entail repeated solution of a sequence of nonlinear programming problems with careful relaxations and approximations, making them sensitive to assumptions and underlying models [18]. Furthermore, the popular branch and bound algorithm used in solving MDNLPs [16] does not apply here since the optimization problem depends indirectly on the material index through the database.
Paper Overview
The primary contribution of this work is the use of variational autoencoders (VAEs) to solve such problems. VAEs are a special form of neural networks that can convert discrete data, such as a material database, into a continuous and differentiable representation, making the design problem amenable to gradient-based optimization. In the proposed method (see Figure 2), a data-driven VAE is trained using a material database, and the trained decoder is then integrated with neural networks to simultaneously optimize the geometry and material.
Figure 2. An overview of the proposed method.
The proposed VAE framework is discussed in § 2. In § 3, the VAE is integrated with two additional and simple neural networks to solve the truss design problem. Specifically, we leverage the differentiable material representation to simultaneously optimize the geometry and material. § 4 demonstrates the proposed framework through several numerical examples. In § 5, limitations and future work are discussed.
A Differentiable Material Representation
In this section, we discuss how variational autoencoders (VAEs) can be used to obtain a continuous and differentiable representation of a discrete material database. This will serve as a foundation for the next section on design optimization.
VAE Architecture and Training
VAEs are popular generative models that have wide applicability in data compression, semi-supervised learning and data interpolation; please see [19]. In essence, a VAE captures the data in a form that can be used to synthesize new samples similar to the input data. For example, VAEs have been used to generate new microstructures from image databases [20], in designing photonic crystals [21], and heat-conduction materials [22].
However, in this paper, we do not use VAEs to synthesize new data, instead we simply use the VAE’s ability to map uncorrelated data onto an abstract latent space. In that sense, VAEs are similar to principal component analysis (PCA) in its ability to extract useful information from the data. However, the nonlinear nature of VAEs allows for far greater generalization than PCA [23]. In particular, the proposed VAE architecture for capturing material properties is illustrated in Figure 3, and consists of the following components:
Figure 3. Architecture of the variational autoencoder.
A four-dimensional input module corresponding to the four properties in table 1, namely the Young’s modulus , cost , mass density and yield strength . The input set is denoted by .
An encoder consisting of a fully-connected network of 250 neurons, where each neuron is associated with an ReLU activation function and weights [24].
A two-dimensional latent space, denoted by that lies at the heart of the VAE.
A decoder , which is similar to the encoder, consists of a fully-connected network of 250 neurons.
A four-dimensional output corresponding to the same four properties; the output set is denoted by .
In this work, the VAE was trained on a material database consisting of 92 materials [25], where table 1 represents a small sample.
| Material | Class | cost | | | |||
| A286 Iron | Steel | 2.01E+11 | 5.18E+00 | 7.92E+03 | 6.20E+08 |
| AISI 304 | Steel | 1.90E+11 | 2.40E+00 | 8.00E+03 | 5.17E+08 |
| Gray Cast Iron | Steel | 6.62E+10 | 6.48E-01 | 7.20E+03 | 1.52E+08 |
| 3003-H16 | Al Alloy | 6.90E+10 | 2.18E+00 | 2.73E+03 | 1.80E+08 |
| 5052-O | Al Alloy | 7.00E+10 | 2.23E+00 | 2.68E+03 | 1.95E+08 |
| 7050-T7651 | Al Alloy | 7.20E+10 | 2.33E+00 | 2.83E+03 | 5.50E+08 |
| Acrylic | Plastic | 3.00E+09 | 2.80E+00 | 1.20E+03 | 7.30E+07 |
| ABS | Plastic | 2.00E+09 | 2.91E+00 | 1.02E+03 | 3.00E+07 |
| PE HD | Plastic | 1.07E+09 | 2.21E+00 | 9.52E+02 | 2.21E+07 |
Table 1. A curated subset of materials and their properties used in the training.
As mentioned earlier, the VAE’s primary task is to match the output to the input as closely as possible. This is done through an optimization process (also referred to a training), using the weights associated with the encoder and decoder as optimization parameters. In other words, we minimize . Additionally, a KL divergence loss is imposed to ensure that latent space resembles a standard Gaussian distribution [19]. Thus, the net loss can then expressed as:
where is set to a recommended value of . Further the input is scaled between for all attributes, and the output is re-scaled back after training. This ensures that all material properties are weighted equally. In this work, we used PyTorch [26] to model the VAE, and the gradient-based Adam optimizer [27] to minimize eq. (5) with a learning rate of 0.002 and 50, 000 epochs. The convergence is illustrated in Figure 4; the training took approximately 51 seconds on a Macbook M1 pro.
Figure 4. Convergence plot during training of the VAE.
Thus, the VAE captures each material uniquely and unambiguously using a non-dimensional latent space, i.e., , in our case; this is visualized in Figure 5. For example, annealed AISI 4340 is represented by the pair while Acrylic is represented by . The VAE also clusters similar materials together in the latent space, as can be observed in Figure 5. In an abstract sense, the latent space in Figure 5 is similar to the popular Ashby charts [5].

Figure 5. Encoding of the materials in the latent space; only a few materials are annotated for clarity.
Representational Accuracy
One can expect the values reconstructed using the decoder to deviate from the true material data; table 2 summarizes the errors. The following observations are worth noting:
Despite the lack of correlation between material properties, and two orders of magnitude difference in values, the VAE captures the entire database of 92 materials reasonably well, using a simple two-dimensional latent space.
The error can be further reduced by either increasing the dimension of the latent space, or limiting the type of materials considered (see § 4).
Finally, as will be discussed in the next section, the original material data will be used, as part of a post-processing step, at the end of optimization.
| Material | ||||
| A286 Iron | 0.8 | 0.7 | 0.8 | 0.0 |
| ABS | 1.4 | 0.0 | 0.7 | 1.7 |
| AISI 304 | 4.3 | 3.1 | 0.4 | 1.0 |
| Gray Cast Fe | 1.3 | 1.8 | 0.2 | 0.2 |
| 3003-H16 | 3.2 | 6.8 | 1.3 | 1.1 |
| 5052-O | 1.4 | 2.4 | 0.6 | 1.2 |
| 7050-T7651 | 0.9 | 1.9 | 1.0 | 1.9 |
| Acrylic | 2.3 | 0.5 | 0.2 | 0.5 |
| PE HD | 0.7 | 0.9 | 1.1 | 1.8 |
| Max error | 5.0 | 6.8 | 3.3 | 7.1 |
Table 2. Percentage error between actual and decoded data.
Differentiability of Latent Space
A crucial aspect of the latent space is its differentiability. In particular, we note that using the decoder, each of the output material properties is represented via analytic activation functions; for example, where is a combination of activation functions and weights. It means that one can back propagate through the decoder to compute analytical sensitivities; for example, the sensitivity . This plays an important role in gradient-driven design optimization.
Material Similarity
While the accuracy and differentiability of the VAE lends itself to design optimization, the latent space also provides key insights into material characteristics. For instance, one can compute the Euclidean distance between materials in the latent space. These distances are reported in Figure 6. As one can expect, steels are closer to aluminum alloys, than they are to plastics.
Figure 6. Symmetric distance in the latent space between materials
Furthermore, one can overlay the latent space in Figure 5 with specific material properties to gain further insight. This is illustrated in Figure 7 where the contour plots of the Young’s moduli are illustrated in the latent space. This allows designers to visualize similarities between materials, specific to a material property.

Figure 7. Contours of the Young’s moduli in the latent space.
Design Optimization
Having constructed a differentiable representation of material properties, one can now pose the optimization problem discussed in section 1, now using as continuous design variables. Without a loss in generalization, we consider a specific instance of the truss optimization problem, where the objective is the compliance with three sets of constraints: cost constraint, buckling constraint, and tensile yield constraint. We assume here that members will fail due to buckling, before failing due to compressive yield [4]. The resulting optimization problem for circular truss members
can be posed as [28]:
where is the internal force in member , is its length, is the allowable cost, is the safety factor, and the material properties are decoded from the latent space coordinates . Further, to facilitate gradient driven optimization, the operator is relaxed here using a p-norm, i.e., , with .
To solve the above optimization we use two additional neural networks (NNs) (see Figure 8a): a truss network , parameterized by weights , and a material network , parameterized by weights . The truss network is a simple feed-forward NN with two hidden layers with a width of 20 neurons, each containing an ReLU activation function. The output layer of consists of neurons where is the number of truss members, activated by a Sigmoid function, generates a vector of size whose values are in . The output is then scaled as to satisfy the area bounds eq. (3f). The material network (Figure 8b) is similar to , except that the output layer consists of two output neurons activated by Sigmoid functions. The outputs are scaled as , resulting in corresponding to six Gaussian deviations. These outputs now interface with the trained decoder from Figure 3. Thus, by varying the weights of the material network one can create points in the latent space, that then feeds to the trained decoder resulting in values of material constants.
Figure 8. The truss and material neural networks.
Loss Function
With the introduction of the two NNs, the weights now control the areas , while the weights control the material constants . In other words, the weights and now form the design variables. Further, since NNs are designed to minimize an unconstrained loss function, we convert the constrained minimization problem in eq. (3) into an unconstrained minimization by employing a log-barrier scheme as proposed in [29]:
where,
with the parameter updated during each iteration (as described in the next section). Thus the optimization problem reduces to a simple form:
A schematic of the proposed framework is presented in Figure 9.
Figure 9. Forward computation
Structural Analysis
We rely on classical structural analysis to evaluate the performance of the truss structure during each iteration. The solver compute the stiffness matrix for each element and upon assembling the global stiffness matrix, the nodal displacement vector are computed using a sparse solver in PyTorch [26]. This allows us to exploit backward propagation for automatic differentiation [30], resulting in an end-to-end differentiable solver with automated sensitivity analysis as described next.
Sensitivity Analysis
In the proposed framework, the loss function in eq. (7) is minimized using gradient-based Adagrad optimizer [31]. Further, the sensitivities are computed automatically using back propagation. A schematic representation of the backward computation graph is shown in Figure 10. For instance the sensitivity of the loss function with respect to the weights can be expressed as:
Figure 10. Backward computation
This is illustrated in Figure 10 where each term corresponds to an edge in the graph. Similarly, the sensitivity with respect to is given by:
These are once again illustrated in Figure 10. Note that the backward computation is carried out automatically in the proposed framework.
Post Processing
Once the optimization process is complete, we obtain an optimal set of latent coordinates . However, there might not exist a material in the database corresponding precisely to . We therefore define a confidence metric for each material by using the distance from to the material in the latent space:
The metric serves to rank the materials based on their distance from . After finding the closest material, we repeat the geometry optimization to compute the optimal areas . This is analogous to the rounding method in discrete optimization [16]: "After rounding, it is usually best to repeat the optimization once more, allowing only the continuous design variables to vary. This process may not lead to the exact optimum, and sometimes may not even lead to a feasible solution, but for many problems this is an effective approach." This is explored further through numerical experiments in § 4.
Algorithm
The proposed algorithms are summarized in this section. As mentioned earlier, we assume that a material database has been provided. The procedure begins with training the VAE as described in algorithm 1. The encoder is then discarded, and the decoder retained. In algorithm 2, starting with the given truss, specified loads, restraints, area bounds and other constraints, the areas and material are optimized. In our experiments and , and the learning rate for the Adagrad optimizer was set to the value of . Once optimized, we find the optimal areas using the nearest material in the latent space.
Numerical Experiments
In this section, we present results from several experiments that illustrate the method and algorithm.
Simultaneous Optimization of Area and Material
The central hypothesis of this paper is that simultaneous optimization of material and geometry leads to superior performance compared to sequential optimization. To validate this hypothesis, we consider the 6-bar truss system illustrated in Figure 11, and perform the following three experiments:
Figure 11. Loading of 6-bar mid-cantilever truss.
Material optimization: Here the areas are fixed at the initial value of , , and only the material is optimized using the decoder.
Algorithm 1 Encode Materials
1: procedure MATENCODE($\zeta$, $F$, $D$) ▷ Input: Training data, encoder and decoder
2: epoch = 0 ▷ iteration counter
3: repeat ▷ VAE training
4: $F(\zeta) \to \{\mu,\sigma\}$ ▷ Forward prop. encoder
5: $\{\mu,\sigma\} \to z$ ▷ Reparameterization {citep}`[19]`
6: $\{\mu,\sigma\} \to KL(z\|\mathcal{N})$ ▷ KL loss
7: $D(z) \to \hat{\zeta}$ ▷ Forward prop. decoder
8: $\{\zeta,\hat{\zeta},KL\} \to L$ ▷ VAE Loss
9: $w+\Delta w(\nabla L) \to w$ ▷ Update VAE weights, Adam Optimizer
10: epoch ++
11: until error is acceptable ▷ Iterate
12: return $D$ ▷ Trained decoder
Algorithm 2 Truss Optimization
1: procedure TRUSSOPT(truss, loads, restraints, $D^*$, ...) ▷ Input: Initial truss, trained decoder, max cost
2: $k=0$ ▷ iteration counter
3: repeat ▷ Optimization (Training)
4: $NN_T(w_T) \to A$ ▷ Fwd prop $NN_T$; compute truss areas
5: $NN_M(w_M) \to z$ ▷ Fwd prop $NN_M$; compute latent coordinate
6: $D^*(z) \to \hat{\zeta}$ ▷ Fwd prop $D^*$; compute material properties
7: $\{A,\hat{E}\} \to [K]$ ▷ compute stiffness matrix
8: $\{[K],f\} \to u$ ▷ State Eq., FEA eq. (3b)
9: $\{u,f\} \to J$ ▷ Compliance, design objective eq. (3a)
10: $\{A,\hat{\rho},\hat{C}\} \to g_c$ ▷ cost constraint eq. (3c)
11: $\{A,\hat{E}\} \to g_b$ ▷ Buckling constraint eq. (3d)
12: $\{A,\hat{Y}\} \to g_y$ ▷ Yielding constraint eq. (3e)
13: $\{J,g_c,g_b,g_y\} \to L$ ▷ Loss eq. (4)
14: $AD(L \gets w_T,g_c \gets w_T,g_b \gets w_T,g_y \gets w_T) \to \nabla_{w_T}L$ ▷ auto diff. for sens. w.r.t. $NN_T$ eq. (7)
15: $AD(L \gets w_M,g_c \gets w_M,g_b \gets w_M,g_y \gets w_M) \to \nabla_{w_M}L$ ▷ auto diff. for sens. w.r.t. $NN_M$ eq. (8)
16: $w_j+\Delta w_j(\nabla_{w_j}L) \to w_j$; $j=\{T,M\}$ ▷ AdaGrad optimizer step
17: $t \gets t_0\mu^k$ ▷ Increment $t$; log-barrier term
18: $k++$
19: until $\|\Delta w\|<\epsilon^*$ ▷ Check for convergence
20: return $\{z,A\}$
21: Find nearest material and optimize for area ▷ section 3.4
Area optimization: Using the optimal material from the first experiment, the areas are optimized by disregarding the decoder.
Simultaneous material and area optimization: Here the material and areas are optimized simultaneously.
The results are reported in Table 3 for a cost constraint of and a safety factor . Observe that scenario-1 (material optimization) leads to the lowest performance since the areas are not optimized. For this scenario, we also performed a brute-force search wherein the compliance was evaluated for all the materials; the brute-force search also resulted in ‘AISI 4130 norm’ as the best choice. In scenario-2, when the areas are optimized using ‘AISI 4130 norm’ as the material, the performance improved significantly. Finally, the best performance is achieved in scenario-3 when both material and areas are optimized simultaneously. Observe that the optimal material in scenario-3 differs from the one found in scenario-1.
Table 3. Cost constrained optimization of the truss in Figure 11
For scenario-3, Table 4 lists the three closest materials and their confidence values.
| Closest Material | Confidence () |
| 1. AISI 1010 | 90.69% |
| 2. 4032-T6 | 86.64% |
| 3. AISI 1020 | 80.01% |
Table 4. Three closest materials under cost constraint.
As an additional experiment, we replaced the cost constraint (eq. (3c)) in the above problem with a mass constraint:
with ; all other parameters being the same. The results are presented in Table 5. Once again we observe that simultaneous optimization results in the best performance. Furthermore, when cost constrained was imposed, a steel alloy was chosen as the best material, whereas when a mass constrained is imposed, an aluminium alloy was chosen.
Table 5. Mass constrained optimization of the truss in Figure 11
For scenario-3 under mass constraint, Table 6 lists the three closest materials and the confidence values.
| Closest Material | Confidence () |
| 1. Al 2018 | 94.16% |
| 2. Al 380F die | 90.64% |
| 3. Al 2014-T4 | 90.13% |
Table 6. Three closest materials under mass constraint.
Material Database Subsets
While we have used the entire material database in the previous experiment, we now consider subsets of the database. Subsets of materials can often be justified based on experience. The VAE reconstruction error for the full database and three sample subsets is reported in table 7. As one expect, the VAE error reduces for the subsets.
We now carry out a few experiments using these subsets, and report the results. First, for the truss problem in Figure 11, we carry out a cost-constrained simultaneous optimization for the full database, as in the previous section. However, we
| Material class | No. materials | ||||
| All Matls. | 92 | 5.0 | 6.8 | 3.3 | 7.1 |
| Steel | 14 | 0.58 | 2.6 | 0.07 | 1.4 |
| Aluminum | 52 | 0.09 | 0.22 | 0.04 | 2.9 |
| Plastic | 12 | 2.3 | 0.36 | 0.5 | 0.7 |
caption: VAE reconstruction error trained with the full and various material subsets.
now report additional results in table 8. When all materials are considered (row-2), the compliance prior to snapping to the closest material is reported as . The closest material is AISI 1010, resulting in a final compliance of . As one can expect, .
Next, since AISI 1010 is a steel alloy, we now consider only the Steel subset, and carry out simultaneous optimization. The results are reported in row-3. Observe that the raw compliance is surprisingly larger than in the previous row. This can be attributed to the larger VAE reconstruction error when all materials are considered, i.e., is not as reliable as the estimate . Further, after the closest material is selected (AISI 1020), the final compliance is . This is slightly larger than the value in the previous row. This discrepancy is analogous to rounding errors in integer optimization [16].
| Material class | Optimal material | Area () | |||||
| All Matls. | 2.25 | AISI 1010 | 2E11 | 7.9E3 | 3.3E8 | 2.58 | [3.6,3.1,3.1,3.5,1.3,1.2] |
| Steel | 2.6 | AISI 1020 | 2E11 | 7.9E3 | 4.2E8 | 2.6 | [3.7,2.9,3.1,3.8,1.1,1.2] |
caption: Material refinement with cost constraint.
Next, we repeated the above experiment for a mass constraint (instead of a cost constraint) and report the results in table 9. When all materials are considered (row-2), the algorithm converges to the aluminum class, with an optimal material Al 2018, as before. Further, as expected. The results using the aluminum subset is reported in row-3. Now, the optimal material is AA356.0-F, and it differs from Al 2018. Now the performance has significantly improved compared to .
| Material class | Optimal material | Area () | |||||
| All Matls. | 8.21 | Al 2018 | 7.40E10 | 2.80E3 | 4.21E8 | 8.53 | [3.1,2.4,2.5,3.1,1,1] |
| Aluminum | 8.23 | AA356.0-F | 7.24E10 | 2.68E3 | 1.45E8 | 8.38 | [3.2,2.7,2.6,3.2,0.9,1] |
caption: Material refinement with mass constraint.
Convergence
To study the convergence characteristics of simultaneous optimization, we consider the antenna tower illustrated in Figure 12. We impose a cost constraint of $50, factor of safety of , and area bounds . Then the areas and material are simultaneously optimized, resulting in an optimal material of ‘AISI 4130 norm’ and . The convergence in compliance is illustrated in Figure 13. We observe that the material choice converges early while the areas continue to be optimized; this was typical. The optimization took 1.89 seconds, with forward propagation and FEA, accounting for 16% each, while back-propagation consumed 54%.
Figure 12. Loading of 47-bar antenna tower.

Figure 13. Convergence of compliance for the material and area for loading in fig. 12.
Conclusion
Engineers today have access to over 150, 000 materials [32], and this number is growing as new materials are being discovered [33, 34]. This presents a significant challenge to design engineers. In this paper, using variational auto encoders (VAEs), we proposed a generic method to simultaneously select the optimal material, while optimizing the geometry. The proposed method was demonstrated using trusses.
There are several limitations to the proposed method. A heuristic confidence-metric was used, as a final step, to snap from the continuous latent space to the nearest material. While this is a well known method in integer optimization, and was found to be effective in out study, it might lead to discrepancies in performance, as was noted in the numerical experiments. On the other hand, since the proposed method suggests an optimal set of material properties, it could drive material innovation in targeted applications. A very small material database with about 100 materials, with limited number of attributes, was considered here. A larger database and additional attributes needs to be explored. The method could benefit from better tuning of the networks, optimal choice of the NN architecture, and increased latent space.
Despite these limitations, we believe that the method holds promise. For example, it could be extended to topology optimization with material selection, specifically using the NN framework proposed in [35]. Furthermore, inclusion of thermo-elastic properties [36], auxetic properties [37], coating properties [38], global warming indices [13] can also be considered. Inclusion of uncertainty in material properties is also of significant interest. Finally, the method can be extended to the selection of discrete components such as springs, bolts, etc., and to the selection of discrete microstructures [39].
Compliance with ethical standards
The authors declare that they have no conflict of interest.
Reproduction of Results
The Python code pertinent to this paper is available at https://github.com/UW-ERSL/MaTruss. The material data was sourced from SolidWorks.
Acknowledgements
The authors would like to thank the support of National Science Foundation through grant CMMI 1561899.
References
- [1]Rudy Eggert. Engineering design. Pearson/Prentice Hall, 2005.
- [2]G. I. N. Rozvany, Bendsoe M.P., and U. Kirsch. Layout optimization of structures. Applied Mechanics Reviews, 48(2):41–119, 02 1995.DOI
- [3]W Achtziger. Truss topology optimization including bar properties different for tension and compression. Structural optimization, 12(1):63–74, 1996.DOI
- [4]Sourav Rakshit and GK Ananthasuresh. Simultaneous material selection and geometry design of statically determinate trusses using continuous optimization. Structural and Multidisciplinary Optimization, 35(1):55–68, 2008.DOI
- [5]Michael F Ashby and David CEBON. Materials selection in mechanical design. Le Journal de Physique IV, 3(C7):C7–1, 1993.
- [6]Michael F Ashby and Kara Johnson. Materials and design: the art and science of material selection in product design. Butterworth-Heinemann, 2013.
- [7]MF Ashby. Multi-objective optimization in material design and selection. Acta materialia, 48(1):359–369, 2000.DOI
- [8]A Jahan, MY Ismail, SM Sapuan, and F Mustapha. Material screening and choosing methods–a review. Materials & Design, 31(2):696–705, 2010.DOI
- [9]R Venkata Rao. A material selection model using graph theory and matrix approach. Materials Science and Engineering: A, 431(1-2):248–255, 2006.DOI
- [10]Chang-Chun Zhou, Guo-Fu Yin, and Xiao-Bing Hu. Multi-objective optimization of material selection for sustainable products: artificial neural networks and genetic algorithm approach. Materials & Design, 30(4):1209–1215, 2009.DOI
- [11]GK Ananthasuresh and MF Ashby. Concurrent design and material selection for trusses. 2003.
- [12]Mathias Stolpe and Krister Svanberg. A stress-constrained truss-topology and material-selection problem that can be solved by linear programming. Structural and Multidisciplinary Optimization, 27(1):126–129, 2004.DOI
- [13]Ernest Ching and Josephine V Carstensen. Truss topology optimization of timber–steel structures for reduced embodied carbon design. Engineering Structures, page 113540, 2021.DOI
- [14]Satadru Roy, William A Crossley, and Samarth Jain. A hybrid approach for solving constrained multi-objective mixed-discrete nonlinear programming engineering problems. 2021.DOI
- [15]JS Arora, MW Huang, and CC Hsieh. Methods for optimization of nonlinear problems with discrete variables: a review. Structural optimization, 8(2):69–85, 1994.DOI
- [16]Joaquim RRA Martins and Andrew Ning. Engineering design optimization. Cambridge University Press, 2021.DOI
- [17]J. Lee and S. Leyffer. Mixed Integer Nonlinear Programming. The IMA Volumes in Mathematics and its Applications. Springer New York, 2011.
- [18]Matthias Köppe. On the complexity of nonlinear mixed-integer optimization. In Mixed Integer Nonlinear Programming, pages 533–557. Springer, 2012.
- [19]Diederik P Kingma and Max Welling. An introduction to variational autoencoders. arXiv preprint arXiv:1906.02691, 2019.DOI
- [20]Liwei Wang, Yu-Chin Chan, Faez Ahmed, Zhao Liu, Ping Zhu, and Wei Chen. Deep generative modeling for mechanistic-based learning and design of metamaterial systems. Computer Methods in Applied Mechanics and Engineering, 372:113377, 2020.DOI
- [21]Xiang Li, Shaowu Ning, Zhanli Liu, Ziming Yan, Chengcheng Luo, and Zhuo Zhuang. Designing phononic crystal with anticipated band gap through a deep learning based data-driven method. Computer Methods in Applied Mechanics and Engineering, 361:112737, 2020.DOI
- [22]Tinghao Guo, Danny J Lohan, Ruijin Cang, Max Yi Ren, and James T Allison. An indirect design representation for topology optimization using variational autoencoder and style transfer. In 2018 AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, page 0804, 2018.
- [23]Ian Goodfellow, Yoshua Bengio, and Aaron Courville. Deep Learning. MIT Press, 2016.
- [24]Jürgen Schmidhuber. Deep learning in neural networks: An overview. Neural networks, 61:85–117, 2015.
- [25]Dassault Systèmes. Solidworks. http://www.solidworks.com, May 2021.
- [26]Adam Paszke, Sam Gross, Francisco Massa, Adam Lehrer, James Bradbury, Gregory Chanan, Trevor Killeen, Zeming Lin, Natalia Gimelshein, Luca Antiga, Alban Desmaison, Andreas Kopf, Edward Yang, Zachary DeVito, Martin Raison, Alykhan Tejani, Sasank Chilamkurthy, Benoit Steiner, Lu Fang, Junjie Bai, and Soumith Chintala. Pytorch: An imperative style, high-performance deep learning library. In Advances in Neural Information Processing Systems 32, pages 8024–8035. Curran Associates, Inc., 2019.arxiv.org/abs/1912.01703
- [27]Diederik P. Kingma and Jimmy Lei Ba. Adam: A method for stochastic optimization. In 3rd International Conference on Learning Representations, ICLR 2015 - Conference Track Proceedings. International Conference on Learning Representations, ICLR, dec 2015.arxiv.org/abs/1412.6980
- [28]Krishnan Suresh. Design Optimization using MATLAB and SOLIDWORKS. Cambridge University Press, 2021.DOI
- [29]Hoel Kervadec, Jose Dolz, Jing Yuan, Christian Desrosiers, Eric Granger, and I Ben Ayed. Constrained deep networks: Lagrangian optimization via log-barrier extensions. CoRR, abs/1904.04205, 2(3):4, 2019.DOI
- [30]Aaditya Chandrasekhar, Saketh Sridhara, and Krishnan Suresh. Auto: a framework for automatic differentiation in topology optimization. Structural and Multidisciplinary Optimization, 64(6):4355–4365, Dec 2021.DOI
- [31]John Duchi, Elad Hazan, and Yoram Singer. Adaptive subgradient methods for online learning and stochastic optimization. Journal of machine learning research, 12(7), 2011.
- [32]Michael F. Ashby. Chapter 1 - introduction. In Michael F. Ashby, editor, Materials Selection in Mechanical Design (Fourth Edition), pages 1–13. Butterworth-Heinemann, Oxford, fourth edition edition, 2011.
- [33]Logan Ward, Ankit Agrawal, Alok Choudhary, and Christopher Wolverton. A general-purpose machine learning framework for predicting properties of inorganic materials. npj Computational Materials, 2(1):1–7, 2016.
- [34]Xiou Ge, Richard T Goodwin, Jeremy R Gregory, Randolph E Kirchain, Joana Maria, and Lav R Varshney. Accelerated discovery of sustainable building materials. arXiv preprint arXiv:1905.08222, 2019.arxiv.org/abs/1905.08222
- [35]Aaditya Chandrasekhar and Krishnan Suresh. Tourn: Topology optimization using neural networks. Structural and Multidisciplinary Optimization, 63(3):1135–1149, Mar 2021.DOI
- [36]Oliver Giraldo-Londoño, Lucia Mirabella, Livio Dalloro, and Glaucio H Paulino. Multi-material thermomechanical topology optimization with applications to additive manufacturing: Design of main composite part and its support structure. Computer Methods in Applied Mechanics and Engineering, 363:112812, 2020.
- [37]Koshi Takenaka. Negative thermal expansion materials: technological key for control of thermal expansion. Science and technology of advanced materials, 13(1), feb 2012.pubmed.ncbi.nlm.nih.gov/27877465
- [38]Anders Clausen, Niels Aage, and Ole Sigmund. Topology optimization of coated structures and material interface problems. Computer Methods in Applied Mechanics and Engineering, 290:524–541, 2015.
- [39]Yu-Chin Chan, Daicong Da, Liwei Wang, and Wei Chen. Remixing functionally graded structures: Data-driven topology optimization with multiclass shape blending. arXiv preprint arXiv:2112.00648, 2021.DOI







