WorksPhysics and Astronomy
Photonic Crystal Integrated Graphene-Silicon Schottky Diodes for Resonant Infrared Photodetection
Abstract
Narrowband infrared (IR) photodetection has become a critical technology for the next generation of smart low-power photodetectors. In this work, we present a device based on a graphene-silicon Schottky junction with narrowband response in the short-wave IR (SWIR) regime. Integrating a photonic crystal (PhC) slab in the device enables a wavelength dependant tailoring of graphene absorption. The devices were characterized by photocurrent measurement, which was enhanced more than two orders of magnitude by the PhC integration. The sharp enhancements obtained can also be predicted by numerical simulation. This approach offers a highly scalable, tunable, CMOS-compatible architecture for narrowband IR photodetection, paving the way for next-generation, low-power IR sensors.
The infrared (IR) spectrum holds relevant information for a wide range of scientific and industrial applications. In recent years, there has been a massive surge in demand for IR sensors across fields such as autonomous vehicles, consumer electronics, biosensing and telecommunications [1, 2, 3, 4]. The move towards higher data transfer bandwidth makes the development of IR photodetectors (PDs) highly valuable. Specifically, the O-band (1310nm) and C-band (1550nm) for optical telecommunication reside in the short-wave IR (SWIR) regime [5, 6, 7]. Narrowband PDs enable more efficient data transfer, suppressing signal noise and improving channel fidelity. Furthermore, single-wavelength detection is essential in environmental monitoring, as it allows the detection of characteristic molecular absorption bands. Moreover, narrowband PDs have already proved to be highly valuable for on-chip spectroscopy in smart sensing devices [8]. Single-wavelength tunable detection is the critical requirement for in-sensor computing devices. This technology can help to reduce computational load and power consumption in the next generation of PDs. Silicon (Si) holds an unrivalled position within the semiconductor industry, making the direct integration of IR-sensitive technologies into silicon-based architectures highly valuable for scalable optoelectronics. However, its bandgap of 1.1 eV, which renders it transparent to infrared radiation, remains a fundamental limitation [9]. Currently, the fabrication of Si-based IR photodetectors relies on heterogeneous integration and monolithic epitaxial growth of narrow bandgap materials, such as III-V semiconductors, on silicon platforms [10, 11]. Therefore, the development of a CMOS-compatible narrow-band photodetector remains highly valuable. Graphene (Gr) is an ideal IR-sensitive candidate for seamless integration into existing CMOS architectures [12, 13, 14, 15, 16]. Thanks to its gapless semimetal nature, it offers uniform broadband absorption over a wide spectral range and an ultrafast response owing to its ultrahigh carrier mobility [13, 17]. However, the absorption of pristine single-layer graphene is fundamentally limited to (where is the fine structure constant), making it practically challenging to use in applications requiring high sensitivity [18]. To overcome the intrinsic optical limitations of graphene, various strategies have been explored to improve its performance for photodetection applications [19, 20, 21, 22].
However, developing PDs with tunable narrow resonances remains challenging. Although metallic plasmonic nanostructures can provide spectrally localized increases in photoresponsivity, the resonances obtained through these techniques are typically broad and severely hindered by Ohmic losses [23, 24, 25]. The integration of graphene channels into Fabry-Pérot nanocavity resonators has been shown to yield strong, narrow resonances. Nevertheless, this approach relies on the complex fabrication of multilayer distributed Bragg reflectors, where the resonant wavelength is strictly fixed by the cavity’s physical dimensions. Consequently, arbitrarily tuning its spectral position remains highly challenging, rendering its implementation in in-sensor computing impractical [26]. Furthermore, the development of highly selective Gr-based IR photodetectors remains largely underexplored, as the bandgap of conventional host semiconductors restricts sub-bandgap absorption entirely to the weak intrinsic response of Gr.
Here, we present a CMOS-compatible and highly integrable Gr-Si architecture designed to engineer the device’s spectral photoresponsivity to achieve a narrowband response in the short-wave infrared (SWIR) regime while simultaneously overcoming the weak intrinsic graphene absorption. Our device offers a predictable, controllable, sharp enhancement of photocurrent by integrating a photonic crystal (PhC) on the silicon side of a Gr-Si Schottky diode, using a standard commercial silicon-on-insulator (SOI) wafer. This simplicity is especially valuable for in-sensor computing, which requires a number of resonances at different wavelengths, as these can all be defined in a single lithographic run. PhCs have been extensively studied for their ability to trap light and support guided resonances. The integration of a PhC into a Gr-Si device makes it possible to confine resonant modes on its surface and enhance graphene absorption in a strongly wavelength-dependent manner [27, 28, 29, 30]. Figure 1a illustrates the narrow enhancement from integrating a PhC into a Gr-Si Schottky junction. We measured the output photocurrent at the PhC resonant wavelength to be more than two orders of magnitude () higher than that of a bare Gr-Si device. As conceptually represented in Figure 1b, the PhC under study consists of a square lattice arrangement of circular nanoholes in a thin Si slab residing on a layer from an SOI wafer. Furthermore, the spectral position of the device’s resonant modes can be tuned by modifying the geometrical parameters of the PhC: in Figure 1a, the two photocurrent enhancement peaks correspond to different PhC hole radii () with a fixed unit cell size ().
Figure 1. a) Spectrum of the photocurrent enhancement compared to a bare Gr-Si device due to a photonic crystal (PhC) with unit cell size and hole radii () of 75nm (blue) and 50nm (orange), respectively. b) Schematic of the device design: Graphene sheet on top of the 220nm thin Si PhC slab residing on a 2µm SiO2 layer. The inset shows a scanning electron microscope image of the graphene sheet on the PhC slab.
The PhC-integrated Gr-Si photodetectors were fabricated using standard nanofabrication techniques. A SOI wafer with a 220 nm p-doped device layer and 2 m insulating layer was covered with 60 nm by atomic layer deposition. 250 windows were wet-etched using buffered HF (BOE), exposing the silicon in the device region of the SOI. The photonic crystals were patterned by electron beam lithography (EBL) and etched by an /Ar reactive ion etching (RIE) plasma. Graphene grown by chemical vapour deposition (CVD) was wet transferred and shaped using EBL and -plasma RIE. The contacts were deposited by evaporation of 5 nm Ti and 50 nm Au. The photocurrent spectrum of the devices was characterized by normal incidence illumination of the Gr-Si junction using a supercontinuum laser with a wavelength resolution of 1 nm. The laser was focused on the device to a beam spot diameter of with an incident power on the order of 300 at 1550 nm, the full power spectrum is available in Figure S2. The signal was modulated at 20 Hz and measured using a lock-in amplifier with a 1 s integration time. The bias voltage () was applied by means of a transimpedance amplifier to bring the device into the reverse-biased state. A more detailed description of the measurement setup is available in Figure S3.
The inclusion of a PhC into a Gr-Si photodetector allows us to engineer the device’s spectral photoresponsivity in a straightforward manner. To design a device with a specific spectral position of the PhC resonant modes, we simulate the absorption spectrum of the graphene layer with the finite-difference time-domain method, using an open-source software package [31]. We represent the graphene layer in our simulations by a one-pixel-thick conductor with the refractive index of graphene scaled by the simulation’s resolution. In Figure 2, we show measured photocurrent spectra and compare them to the simulated absorption in graphene of a typical device with geometrical parameters and ranging from 25 to 150 nm. As predicted by the simulation, two narrow resonant peaks appear in the 1200–1600 nm range. The photocurrent peak positions match the simulated absorption spectra, with some deviation due to fabrication tolerance discrepancies. The scanning electron microscope images of the PhCs are available in Figure S1. A blueshift of the resonant peaks is observed for both the simulated absorption and the measured photocurrent spectra when increasing the PhC hole radii. This occurs because larger holes increase the air filling factor of the Si slab, reducing its effective refractive index [28, 32]. The effective maximum responsivity of this device was measured to be 18 . The laser power spectrum is available in Figure S2.
Figure 2. Comparison between simulated graphene absorption and measured photocurrent. Photocurrent spectra measured at bias voltage of a PhC-integrated Gr-Si Schottky diode photodetector with a unit cell size of and different hole radii.
In the IR regime, the Gr-Si device operation is attributed to the internal photoemission mechanism, where photon absorption occurs in graphene, and the resulting photoexcited hot carriers can be injected into the Si across the Schottky barrier. For effective injection across the Schottky barrier, hot carriers must simultaneously satisfy the correct energy and momentum conditions. Ultrafast thermalization in graphene further reduces the population of carriers that can inject into silicon, limiting the photocurrent generation[33, 34]. Previous works predicted 100% absorption occurring for critical coupling in Gr-Si devices [27, 35]. Critical coupling conditions require rate matching in open resonators: the absorption in the graphene layer must exactly balance the radiative decay rate of the cavity [36]. Therefore, total absorption cannot be achieved with the current device’s design, as the absence of a highly reflective bottom layer leaves the transmission channel open. The integration of a back reflector into the architecture introduces substantial fabrication complexity. According to the simulation data, with this combination of geometrical parameters, it is possible to achieve a maximum theoretical absorption of 86% in the graphene layer, corresponding to a PhC slab with nm and nm.
The PhC’s geometric parameters affect the spatial modes’ positions, numbers, widths, and intensities. PhCs with larger unit cell sizes offer a greater number of resonant modes in the same spectral range compared to PhCs with smaller unit cell sizes. The position of the resonant mode for a given PhC can also be approximately predicted by Bragg phase-matching condition grating-coupling:
where is the effective refractive index for light propagating in the silicon slab, is the PhC unit cell size, and and (with , ), are the diffraction orders. The effective refractive index of the Si slab is calculated using the transverse resonance condition weighted with the hole filling factor [37]. The resonant modes predicted by solving Maxwell’s equations and their approximate prediction by Bragg’s diffraction law are schematically compared in Figure 3a. The Bragg’s diffraction approximation works well for smaller filling factors, after which the structure deviates more from the effective medium theory [38, 39].
Figure 3. a) Simulated absorption spectra in graphene as a function of hole radius (unit cell size nm). The dotted line represents an approximate prediction of the resonant modes obtained using Bragg diffraction theory, along with their mode assignments. b) Absorption spectrum of the nm device with the spatial absorption distribution in the Gr layer of the three resonances on top (full unit cell is shown).
Our simulations also reveal that each absorption resonance is associated with a specific spatial absorption distribution in the Gr layer. The silicon PhC sits between air and a 2 m SiO2 dielectric layer (Figure 1b), making the TE and TM resonant modes non-degenerate due to the refractive index mismatch. Each resonant peak can be attributed to the excitation of fundamental and higher-order guided resonances within the PhC slab. Furthermore, the Bragg condition defines the phase-matching criterion under which the periodic lattice strongly scatters the guided light, generating localized resonances. In Figure 3b, the resonant modes calculated using the Bragg condition are correlated with the absorption peaks, and the corresponding spatial absorption distributions are simulated by solving Maxwell’s equations. A clear correlation between the shape of the spatial distribution and the diffraction order of the Bragg resonant modes is evident. From this, it is possible to conclude that each absorption peak can be attributed to the excitation of fundamental and higher-order guided resonances within the PhC slab, depending on its geometry. In the example reported in Figure 3b, the first peak is associated with a TE0 (1,1) mode that propagates along the diagonal direction of the square lattice. The second peak is defined by a TM0 (1,0) mode propagating along the y-axis, and the third peak corresponds to a TE0 (1,0) mode propagating along the x-axis.
The entire spectral range of interest can be covered by resonant photocurrent-enhancement peaks by selecting appropriate geometrical parameters (, ) for the integrated PhC in the Gr-Si diodes. We show in Figure 4a a collection of PhC-integrated Gr-Si photodetectors and their spectra that cover a broad wavelength range, with isolated resonances characterized by a full width at half maximum (FWHM) around 20 nm. In addition to the resonance tunability, the device’s photocurrent output can be dynamically controlled by means of the bias voltage (Figure 4b). Under reverse bias, the photocurrent increases linearly with down to V, after which the extraction efficiency approaches the maximum, and the photocurrent remains limited by the incident optical generation rate. The residual modest increase in the photocurrent can be attributed to the voltage-induced lowering of the Schottky barrier[9, 40]. The ability to tune the photoresponse is a crucial requirement for developing low-power photodetectors, as they operate effectively within a narrow voltage window, thereby limiting power consumption.

Figure 4. a) Photocurrent spectra of PhC-integrated Gr-Si Schottky diode devices with different geometrical parameters, measured at V. b) Peak photocurrent at 1710 nm for a Gr-Si Schottky diode with PhC geometrical parameters of nm and nm for different .
In conclusion, we demonstrated that the photoresponse of a Gr-Si Schottky diode photodetector can be effectively tuned by integrating a PhC. By optimizing the geometric parameters of the PhC, specifically the unit cell size and air-hole radii, resonant peaks were successfully engineered at targeted spectral positions within the SWIR regime. Furthermore, a close correspondence between the simulated absorption resonances and the measured photocurrent peak positions was observed. This validates the use of numerical simulations as a robust predictive tool for engineering device performance. Crucially, the PhC integration yielded a photocurrent enhancement of more than two orders of magnitude () compared to a planar Gr-Si reference device. Specifically, the PhC integration results in sharp, narrowband resonances in the SWIR regime with FWHM below 20 nm, making the device useful for low-noise, high-precision telecommunications. By careful tuning of the geometrical parameters in a series of Gr-Si devices, we were able to cover the spectral range under study with narrow photocurrent enhancement peaks, making this design highly valuable for in-sensor computing smart photodetectors and spectroscopy applications.
While tuning the 2D lattice parameters proved sufficient to control the spectral response, future optimizations could explore additional degrees of freedom, such as bias voltage, silicon slab thickness, and alternative PhC cavity designs. Controlling more parameters can further maximize the optical field enhancement within the graphene layer. Although the output photocurrent generated by the fabricated devices aligns with that of similar Gr-Si IR photodetectors[41], the absolute photoresponsivity remains limited. This may partially originate from the formation of an interfacial native SiO2 layer, hindering the injection of hot electrons across the Schottky junction. Nevertheless, the primary focus of this study was to isolate and validate the optical enhancement achieved through PhC integration. Addressing these interface limitations in future fabrication processes, combined with the PhC design principles presented in this work, promises to unlock high performance for advanced IR, compatible with silicon-based device architectures.
Acknowledgements
This research was funded in part by the Austrian Science Fund (FWF) [10.55776/DOC142] (TU-DX: Towards Applications of 2D Materials). This research was funded in part (M.H.) by the Austrian Science Fund (FWF) [10.55776/J4729].
References
- [1]Hashemi, H. In 2022 IEEE Custom Integrated Circuits Conference (CICC), IEEE: Newport Beach, CA, USA, 2022, pp 1–8.
- [2]Li, W.; Huang, D. Silicon Photonics Devices and Integrated Circuits. Photonics 2025, 12, 187.DOI
- [3]Butt, M. A.; Pastor Abellán, D.; Piramidowicz, R. Mid-Infrared Integrated Photonics: Material Platforms and Emerging Applications. Laser & Photonics Reviews 2026, 20, e00099.DOI
- [4]Zhuge, F.; Zheng, Z.; Luo, P.; Lv, L.; Huang, Y.; Li, H.; Zhai, T. Nanostructured Materials and Architectures for Advanced Infrared Photodetection. Advanced Materials Technologies 2017, 2, 1700005.DOI
- [5]Wu, Z.; Ou, Y.; Cai, M.; Wang, Y.; Tang, R.; Xia, Y. Short-Wave Infrared Photodetectors and Imaging Sensors Based on Lead Chalcogenide Colloidal Quantum Dots. Advanced Optical Materials 2023, 11, 2201577.DOI
- [6]Bruns, O. T. et al. Next-generation in vivo optical imaging with short-wave infrared quantum dots. Nature Biomedical Engineering 2017, 1, 0056.
- [7]Crisci, T.; Moretti, L.; Russo, C.; Gioffrè, M.; Iodice, M.; Coppola, G.; Casalino, M. Unveiling high responsivity in on-chip photodetectors with graphene interposed between amorphous and crystalline silicon. Carbon 2025, 233, 119837.DOI
- [8]Kwak, D.; Polyushkin, D. K.; Mueller, T. In-sensor computing using a MoS2 photodetector with programmable spectral responsivity. Nature Communications 2023, 14, 4264.DOI
- [9]Sze, S.; Ng, K. K., Physics of Semiconductor Devices, 1st ed.; Wiley: 2006.
- [10]Roelkens, G. et al. III-V-on-Silicon Photonic Devices for Optical Communication and Sensing. Photonics 2015, 2, 969–1004.DOI
- [11]Zeng, C.; Fu, D.; Jin, Y.; Han, Y. Recent Progress in III–V Photodetectors Grown on Silicon. Photonics 2023, 10, 573.DOI
- [12]Bonaccorso, F.; Sun, Z.; Hasan, T.; Ferrari, A. C. Graphene photonics and optoelectronics. Nature Photonics 2010, 4, 611–622.DOI
- [13]Novoselov, K. S.; Geim, A. K.; Morozov, S. V.; Jiang, D.; Zhang, Y.; Dubonos, S. V.; Grigorieva, I. V.; Firsov, A. A. Electric Field Effect in Atomically Thin Carbon Films. Science 2004, 306, 666–669.pubmed.ncbi.nlm.nih.gov/15499015
- [14]Jalali, B.; Fathpour, S. Silicon Photonics. Journal of Lightwave Technology 2006, 24, 4600–4615.
- [15]Koppens, F. H. L.; Mueller, T.; Avouris, P.; Ferrari, A. C.; Vitellio, M. S.; Polini, M. Photodetectors based on graphene, other two-dimensional materials and hybrid systems. Nature Nanotechnology 2014, 9, 780–793.DOI
- [16]Romagnoli, M.; Sorianello, V.; Midrio, M.; Koppens, F. H. L.; Huyghebaert, C.; Neumaier, D.; Galli, P.; Templ, W.; D’Errico, A.; Ferrari, A. C. Graphene-based integrated photonics for next-generation datacom and telecom. Nature Reviews Materials 2018, 3, 392–414.
- [17]Bolotin, K.; Sikes, K.; Jiang, Z.; Klima, M.; Fudenberg, G.; Hone, J.; Kim, P.; Stormer, H. Ultrahigh electron mobility in suspended graphene. Solid State Communications 2008, 146, 351–355.DOI
- [18]Nair, R. R.; Blake, P.; Grigorenko, A. N.; Novoselov, K. S.; Booth, T. J.; Stauber, T.; Peres, N. M. R.; Geim, A. K. Fine Structure Constant Defines Visual Transparency of Graphene. Science 2008, 320, 1308–1308.DOI
- [19]Pospischil, A.; Humer, M.; Furchi, M. M.; Bachmann, D.; Guider, R.; Fromherz, T.; Mueller, T. CMOS-compatible graphene photodetector covering all optical communication bands. Nature Photonics 2013, 7, 892–896.DOI
- [20]Gan, X.; Shiue, R.-J.; Gao, Y.; Meric, I.; Heinz, T. F.; Shepard, K.; Hone, J.; Assefa, S.; Englund, D. Chip-integrated ultrafast graphene photodetector with high responsivity. Nature Photonics 2013, 7, 883–887.DOI
- [21]Riazimehr, S.; Kataria, S.; Gonzalez-Medina, J. M.; Wagner, S.; Shaygan, M.; Suckow, S.; Ruiz, F. G.; Engström, O.; Godoy, A.; Lemme, M. C. High Responsivity and Quantum Efficiency of Graphene/Silicon Photodiodes Achieved by Interdigitating Schottky and Gated Regions. ACS Photonics 2019, 6, 107–115.DOI
- [22]Pella, A.; Grillo, A.; Faella, E.; Luongo, G.; Askari, M. B.; Di Bartolomeo, A. Graphene–Silicon Device for Visible and Infrared Photodetection. ACS Applied Materials & Interfaces 2021, 13, 47895–47903.
- [23]Wang, D.; Allcca, A. E. L.; Chung, T.-F.; Kildishev, A. V.; Chen, Y. P.; Boltasseva, A.; Shalaev, V. M. Enhancing the graphene photocurrent using surface plasmons and a p-n junction. Light: Science & Applications 2020, 9, 126.DOI
- [24]Baranov, D. G.; Zuev, D. A.; Lepeshov, S. I.; Kotov, O. V.; Krasnok, A. E.; Evlyukhin, A. B.; Chichkov, B. N. All-dielectric nanophotonics: the quest for better materials and fabrication techniques. Optica 2017, 4, 814.arxiv.org/abs/1702.00677
- [25]Khurgin, J. B. How to deal with the loss in plasmonics and metamaterials. Nature Nanotechnology 2015, 10, 2–6.DOI
- [26]Furchi, M.; Ulrich, A.; Pospischil, A.; Lilley, G.; Unterrainer, K.; Detz, H.; Klang, P.; Andrews, A. M.; Schrenk, W.; Strasser, G.; Mueller, T. Microcavity-Integrated Graphene Photodetector. Nano Letters 2012, 12, 2773–2777.DOI
- [27]Piper, J. R.; Fan, S. Broadband Absorption Enhancement in Solar Cells withan Atomically Thin Active Layer. ACS Photonics 2016, 3, 571–577.DOI
- [28]Fan, S.; Joannopoulos, J. D. Analysis of guided resonances in photonic crystal slabs. Physical Review B 2002, 65, 235112.DOI
- [29]Rituraj; Yu, Z. G.; Kandedegara, R. M. E. B.; Fan, S.; Krishnamurthy, S. Highly sensitive and efficient 1550 nm photodetector for room temperature operation. AIP Advances 2025, 15, 015215.arxiv.org/abs/2404.15218
- [30]Gu, T.; Andryieuski, A.; Hao, Y.; Li, Y.; Hone, J.; Wong, C. W.; Lavrinenko, A.; Low, T.; Heinz, T. F. Photonic and Plasmonic Guided Modes in Graphene?Silicon Photonic Crystals. ACS Photonics 2015, 2, 1552–1558.
- [31]Oskooi, A. F.; Roundy, D.; Ibanescu, M.; Bermel, P.; Joannopoulos, J.; Johnson, S. G. Meep: A flexible free-software package for electromagnetic simulations by the FDTD method. Computer Physics Communications 2010, 181, 687–702.
- [32]Joannopoulos, J. D.; Winn, J. N.; Johnson, S. G., Photonic Crystals: Molding the Flow of Light - Second Edition; Princeton University Press: Princeton, NJ, 2011.DOI
- [33]Brida, D.; Tomadin, A.; Manzoni, C.; Kim, Y. J.; Lombardo, A.; Milana, S.; Nair, R. R.; Novoselov, K. S.; Ferrari, A. C.; Cerullo, G.; Polini, M. Ultrafast collinear scattering and carrier multiplication in graphene. Nature Communications 2013, 4, 1987.DOI
- [34]Goykhman, I.; Sassi, U.; Desiatov, B.; Mazurski, N.; Milana, S.; De Fazio, D.; Eiden, A.; Khurgin, J.; Shappir, J.; Levy, U.; Ferrari, A. C. On-Chip Integrated, Silicon–Graphene PlasmonicSchottky Photodetector with High Responsivity and Avalanche Photogain. Nano Letters 2016, 16, 3005–3013.DOI
- [35]Piper, J. R.; Fan, S. Total Absorption in a Graphene Monolayer in the Optical Regime by Critical Coupling with a Photonic Crystal Guided Resonance. ACS Photonics 2014, 1, 347–353.DOI
- [36]Wonjoo Suh; Zheng Wang; Shanhui Fan Temporal coupled-mode theory and the presence of non-orthogonal modes in lossless multimode cavities. IEEE Journal of Quantum Electronics 2004, 40, 1511–1518.DOI
- [37]Saleh, B.; Teich, M.; Slusher, R. E. Fundamentals of Photonics. Physics Today 1992, 45, 87–88.
- [38]Lalanne, P.; Lemercier-lalanne, D. On the effective medium theory of subwavelength periodic structures. Journal of Modern Optics 1996, 43, 2063–2085.DOI
- [39]Choy, T. C., Effective Medium Theory: Principles and Applications; Oxford University Press: 2015.DOI
- [40]Di Bartolomeo, A. Graphene Schottky diodes: An experimental review of the rectifying graphene/semiconductor heterojunction. Physics Reports 2016, 606, 1–58.DOI
- [41]Casalino, M.; Sassi, U.; Goykhman, I.; Eiden, A.; Lidorikis, E.; Milana, S.; De Fazio, D.; Tomarchio, F.; Iodice, M.; Coppola, G.; Ferrari, A. C. Vertically Illuminated, Resonant Cavity Enhanced, Graphene–Silicon Schottky Photodetectors. ACS Nano 2017, 11, 10955–10963.


