WorksPhysics and Astronomy
On the Practicability of Ceramic-Tiled Walls for Sound Absorption by Tuning Cavities
Abstract
We present the practicality of structuring ceramic tiles for enhancing sound absorption on rigid walls. The cornerstone of our methodology is to structure walls with cavities so that walls effectively behave as heterogeneous absorbing surfaces over a large frequency bandwidth. Using this approach, ceramic tiled walls are developed by integrating tuned cavity structures based on Helmholtz resonators. Such a design leverages the empty joints between tiles to form resonator necks, while the space between the ceramic tiles and the wall acts as the resonator chambers. By arranging these resonators in a spatially graded array, we achieve broadband sound absorption which targets low-frequency noise generated by impacts, footsteps and ambient sources. This makes the system highly suitable for practical architectural applications. The study encompasses the entire process, from numerical modeling and analytical formulation to the fabrication and mounting of resonant tiles, followed by experimental validation, clearly demonstrating the effectiveness of the proposed solution in real-world conditions. The findings highlight the strong potential of this approach for practical tiled room acoustic treatment and noise mitigation.
Introduction
Sound absorption is a crucial aspect of acoustic design in architectural and industrial applications, aimed at controlling noise and improving auditory environments. Conventional sound absorption methods primarily rely on porous materials [1, 2] and micro-perforated structures [3, 4], both of which typically require a structural thickness on the order of the acoustic wavelength. To effectively absorb low-frequency sound, which has longer wavelengths, these materials must be significantly thicker, thereby limiting their practical applications [5]. In addition, these absorbers usually result in an imperfect impedance match with the incident wave [6].
Traditional building materials typically rely on their intrinsic material composition, such as density and porosity, to enhance global acoustic properties. In contrast, the performance of metamaterials is primarily governed by their geometric design, structural configuration, or stiffness distribution, allowing them to be tailored into a wide range of functional bulk materials [7, 8, 9]. To address the limitations of conventional materials, acoustic metamaterials have emerged as a promising solution for building insulation, gaining significant attention due to their exceptional wave-control capabilities in complex acoustic environments [8]. These metamaterials are artificially engineered to exhibit unique properties not commonly found in natural materials, spanning multiple disciplines including electromagnetics, optics, solid-state physics, and acoustics. Acoustic metamaterials are typically composed of periodic or aperiodic substructures that enable targeted or unconventional acoustic behavior, often leveraging local resonance phenomena by leveraging subwavelength resonances, wave interference effects or non-localities [7, 10, 11].
Recent advances in the field of acoustic metamaterials [7, 12] have paved the way for innovative solutions to achieve extraordinary effects such as acoustic cloaking [8, 13], wave focusing and negative refraction [14, 15, 16, 17, 18]. Beyond these new capabilities, acoustic metamaterials present promising alternatives to conventional sound-absorbing materials by enabling effective sound absorption at sub-wavelength dimensions. Various acoustic metamaterial designs have been proposed, such as membrane-type absorbers [19, 20], Helmholtz cavities [21, 22, 23, 24, 25], spatial coil resonators [26, 27], neck-integrated Helmholtz cavities [28, 29] and hierarchical porous structures [30, 31]. The search for acoustic metamaterials combining compactness and broadband low-frequency absorption remains a crucial and ongoing area of research.
On the other hand, ceramic tiles are a widely used construction material applied in various parts of buildings, including household roofs, walls, floors, and partitions [32]. In modern architecture, wall tiles are typically designed for durability, abrasion resistance, water impermeability, ease of cleaning, and aesthetic appeal [33]. However, in terms of acoustic absorption performance, ceramic tiles are not effective at reducing noise or sound absorption. Due to their high density and rigid surface, they exhibit poor sound absorption and high sound reflectivity, making them less suitable for applications requiring acoustic insulation in walls.
To address these challenges, we investigate tuning cavity structures [34, 35] as an effective strategy for achieving broadband sound absorption while maintaining the compactness, durability, ease of cleaning, and weather resistance of ceramic tiled walls. The core concept involves incorporating Helmholtz resonators, which are well-known for their ability to absorb low-frequency sound, directly into ceramic subtile assemblies. The gaps between adjacent periodic subtiles function as resonator necks or slits, while the air cavities formed between the subtiles and the wall act as the primary tuning cavities. By arranging an inhomogeneous array of such tuning cavities, broadband sound absorption can be achieved, allowing for efficient mitigation of audible noise over a wide low-frequency range. This approach offers a practical and architecturally seamless solution for noise control, utilizing the inherent structural advantages of ceramic tiles while integrating advanced acoustic functionality.
Therefore, in this study, we present a comprehensive investigation of tuning cavity structures, including numerical modeling, analytical approaches, and experimental validation. We demonstrate their effectiveness in real-world building applications, showing that this design enables high-performance sound absorption without compromising the aesthetic or structural integrity of ceramic wall systems.
Design of the tuning cavity structure
The design method of the tuning cavity structures and the geometric parameters of their constituent units are introduced in this section. In addition, the methods for sound absorption calculations, both numerical and analytical, as well as the fabrication of the experimental sample and the measurement setup, are also discussed.
Materials and design
The structure of the metatile wall, based on tuned cavity units, is illustrated in Figure 1a. It consists of a series of ceramic subtiles of width , separated by slits of width . A gap of width between the ceramic subtiles and the wall forms a cavity that functions similarly to a Helmholtz resonator with the material properties shown in Table I. This cavity plays a crucial role in absorbing sound, thereby enhancing the acoustic performance of ceramic-tiled walls by reducing noise and minimizing sound reflection, all while preserving their aesthetic appearance.

Figure 1. The ceramic metatile wall, which is composed of tuning cavity structures integrated into ceramic subtiles fixed to the wall using wooden beams. (a) Overview of the design (right) of the structural design of the metatile wall along with a zoom-in view of the unit cell (left). With, is the height of the tuning cavity, is the depth of the cavity, and is the width of the cavity slits. The ceramic tiles have a thickness cm and a width of 5 cm, while the wood beams measure 1 cm in both width and depth. The structure is periodic in the -direction, with a periodicity constant denoted by and the incident wave propagates along the -direction. (b) Schematic view of the numerical model with Perfectly Matched Layers (PML) in blue color and elastic medium in grey color. (c) Equivalent resistor, inductor, and capacitor (RLC) circuit model of the unit cell (an impedance cavity ).
| (GPa) | (kg/m) | (Pa.s) | (m/s) | ||
| Ceramic | 55 | 3000 | 0.3 | - | 4967 |
| Air | - | 1.2 | - | 343 |
Table I. Material parameters
To optimize the acoustic performance, we performed simulations considering all structural parameters, with the constraint of maintaining thin cavities and added layers to ensure practical integration into existing walls. To this end, we also incorporated wooden beams with cross-sectional dimensions of 1 cm 1 cm, which serve both as connectors and as supports to bond the ceramic sub-tiles to the wall.
Numerical model
We conduct numerical simulations using the commercial finite element software COMSOL Multiphysics, utilizing the Thermoviscous Acoustics Module. Using this module, we solve the full set of linearized governing equations for compressible, viscous, and thermally conducting fluids in the frequency domain. These include the linearized Navier–Stokes equation 1 for momentum conservation, the continuity equation 2 for mass conservation, and the energy equation 3 for thermal effects:
where denotes the gradient operator, is the acoustic velocity vector, is the acoustic pressure, is the density, is the temperature, and is the angular frequency. The parameters , , , , , , and denote the equilibrium density, ambient temperature, shear viscosity, bulk viscosity, specific heat at constant pressure, thermal expansion coefficient, and thermal conductivity, respectively.
We point out that there is no transmission through the air–ceramic interface, which is modeled as a hard boundary condition , where is the outward unit vector to the surface. Other interfaces are subject to quasi-periodic (Floquet-Bloch) and wall (hard boundary) conditions.
The finite element model is schematically shown in Figure 1(b). To simulate an incident wave, we used a Background Pressure Field applied to the air region in front of the ceramic wall structure and in the air cavity. A normally incident plane wave with unit amplitude is applied along the negative -direction.
The tuning cavity structures are fabricated by ceramic material which has a significantly higher acoustic impedance than air. Due to the large impedance mismatch and negligible structural vibration, the cavity walls are defined as rigid, and hard-wall boundary conditions are applied around the cavity. If the walls are compliant, coupling effects should be taken into account in the acoustic–solid interaction module. Besides, periodic boundary conditions are applied to the lateral sides of the air domain. To resolve the viscous boundary layers, the maximum mesh size inside the slits is set 1/6 to the minimum mesh size. For the air cavities, the maximum element size is kept below 1/8 of the shortest wavelength in the target frequency range. In addition, the scattered pressure is measured on a surface just in front of the ceramic tuning cavity. The reflection coefficient is obtained as the ratio between the scattered and incident acoustic intensity. Then, the absorption coefficient is finally computed using the complex reflection coefficient , extracted from the average sound pressure at the incident boundary as .
Analytical model
In this section, we derive the equivalent model of a cavity tuning as an electrical circuit, and calculate its absorption coefficient for a single resonator and for a series of resonators with different cavity’s volumes, respectively. Our main methodology is to correlate mechanical acoustic parameters to the electrical model and incorporate thermoviscous losses. The sound wave is assumed to be harmonic, with time and frequency dependence given by . In general, the tuning cavity can be modeled as a lumped RLC circuit model. The equivalent electrical circuit of the system is shown in Figure 1(c), with the analogy: inductance represents the acoustic mass of the air in the slit; capacitance represents the compliance of the cavity volume; resistance accounts for Thermoviscous losses in the slit and cavity.
The impedance of a tuning cavity is given by , where is the effective inductance, is the compliance. Here is the angular frequency and , is the air density, is the slit depth, is the cross-sectional area of the slit, is the speed of sound, and is the cavity volume with denoting the length of the subtiles, as depicted in Figure 1(a).
Thermoviscous losses are included in the real part of the impedance. These losses are due to viscous friction of air particles near the walls of the neck. An empirical expression of considering these effects is given as , where is the dynamic viscosity of air.
The absorption coefficient is defined by the impedance mismatch between the resonator and the surrounding medium:
where is the characteristic impedance of air.
Now, we consider tuning cavities placed in parallel with varying cavity’s volumes .
For each resonator we have and , and the absorption coefficient for the -th resonator is:
where is the impedance of the -th resonator. The total absorption coefficient is obtained by the sum: .
Samples and experiments
The experimental setup is based on a custom-built impedance tube system that employs the two-microphone Transfer Function method prescribed in the ISO 10534-2 standard, as depicted in Figure 2(a). This system is utilized to determine both the complex reflection coefficient and the dimensionless sound absorption coefficient of the tuning cavity under normal incidence at various frequencies [36].

Figure 2. Illustration of the experimental system. (a) The experimental setup. The noise signal is generated by a computer that runs a home-made MATLAB code, and is transferred sequentially to the signal analyzer, the amplifier and the loudspeaker. The generated acoustic pressure is measured by two microphones, both of which are connected to the signal analyzer. The recorded signals are then processed using MATLAB, where a Fast Fourier Transform is applied to analyze the sound absorption coefficient. Photography of the ceramic metatile wall: (b) front view and (c) side view.
Ceramic tiles were used as the base material for the subtiles which were then connected to the wall by wooden beams. The ceramic tiles, supplied by IRIS Company, were experimentally characterized through static and dynamic tests under small strain conditions. The measured elastic properties are as follows: Young’s modulus GPa, Poisson’s ratio , and density kg/m [37]. The complete specimen is shown in Figure 2(b) and (c), with overall dimensions of cm.
The apparatus consists of a rigid, rectangular impedance tubes with internal cross-sectional area of cm cm and cm cm and a total length of cm and cm, respectively. A broadband loudspeaker is mounted at one end of the tubes, while the ceramic metatile sample is installed at the opposite end. Two identical microphones are positioned along the side of the tubes at distances of cm and cm from the surface of the tuning cavity structures. These microphones will capture the acoustic pressure corresponding to the incident and reflected waves within the tube. The loudspeaker emits a broadband random signal spanning the frequency range of Hz to Hz. The acoustic pressure at each microphone position is used to solve the pressure field in the tube, which can be modeled as: , where and denote the amplitudes of the incident and reflected waves, respectively, is the acoustic wavenumber, and corresponds to the position of the ceramic metatile cavity. The microphone signals are amplified and digitized using a high-precision, multi-channel dynamic signal acquisition module connected to the computer for further data processing and analysis, see Figure 2(a).
By computing the transfer function between the two microphone signals, one can solve for the complex reflection coefficient
and subsequently deduce the sound absorption coefficient using the relation: .
Results and discussion
Acoustic response of the standard ceramic tile
To better understand the effect of integrating tuned cavity structures into tiled walls, we begin by experimentally and numerically investigating the sound absorption coefficient of a standard ceramic tile, as shown in Figure 3(a). It is well known that standard ceramic tiles exhibit high sound wave reflectivity, in other words, they reflect much of the noise generated by the surrounding environment. Furthermore, we present in Figure 3(b) the sound absorption coefficient as a function of frequency for the standard ceramic tile. It is clear that, in their conventional form, ceramic tiles provide negligible sound absorption and are predominantly reflective. This result serves as a reference for comparison with the subsequent sections, where we transform the standard tiles into metatiles by incorporating tuned cavity resonators based on the Helmholtz resonator. There is a noticeable discrepancy between the experimental and numerical results. In the numerical simulations, we model an infinite ceramic tile by applying periodic boundary conditions, which idealizes the response of a continuous tiled surface. However, in the experimental setup, we use a small tile sample placed inside an impedance tube. Due to the limited sample size, unavoidable gaps exist between the sample edges and the tube walls. These gaps can behave like quarter-wave resonators, introducing additional resonance peaks in the measured absorption spectrum. Furthermore, the dimensions of the impedance tube define the operational frequency range for sound absorption measurements, which is approximately from 200 Hz to 1600 Hz. Outside this range, especially beyond the upper and lower frequency limits, the absorption results become unreliable. This explains the discrepancy between the numerical and experimental results, particularly the additional peaks observed in the experimental data.

Figure 3. Sound absorption coefficient of the standard ceramic tile. (a) Schematic illustration of the ceramic tile. (b) Numerical and experimental responses of the sound absorption coefficient as a function of frequency.
Parametric optimization of the tuning cavity
Considering the requirement of thinner structures in practical building applications, we optimize the geometrical parameters of the tuning cavity, including the slit width , the cavity width , and the cavity length . Additionally, we employ the numerical model illustrated in Figure 1(b), using subtiles of length cm along the -direction.
We begin by varying the slit width from 0.1 mm to 3 mm, while keeping cm and cm. As shown in Figure 4(a), incorporating a slit and a cavity enables efficient absorption of sound waves over the frequency range from 310 Hz to 1290 Hz, depending on the variation of . Furthermore, as the slit width increases (i.e., the neck becomes thicker), the absorption peak shifts toward higher frequencies, and the overall absorption coefficient decreases. This behavior can be explained by the Helmholtz resonance mechanisms, which describe the phenomenon of air resistance in the neck of the cavity. With the increment of the neck width of the Helmholtz resonator, acoustic waves can propagate through the neck with less resistance, resulting in a shift of the resonance frequency to higher values and a reduction in the overall sound absorption.

Figure 4. Absorption coefficient as a function of three key cavity parameters. (a) Thickness of the slit , varied within the range 0.1 to 3 cm. (b) Width of the cavity , varied within the range 0.5 to 5 cm. (c) Length of the cavity , varied within the range 2 to 10 cm.
Then we fix the slit width ( cm) and the cavity length ( cm), and vary the cavity width from 0.5 cm to 5 cm, as shown in Figure 4(b). As the cavity width increases, the absorption peak shifts toward lower frequencies, reaching as low as 250 Hz when cm, where nearly total absorption is observed. This indicates that increasing the cavity volume can enhance low-frequency absorption, but meanwhile results in larger thickness which is not aligned with our primary objective of maintaining compact and thin.
Finally, we study the effect of cavity length by fixing the slit width ( mm) and the cavity width ( cm). This group of parameter keeps the structure thin and small enough to be adaptable for tiled wall applications. We vary from 2 cm to 10 cm to optimize the design by adjusting only this parameter. As illustrated in Figure 4(c), the absorption coefficient shifts toward lower frequencies as the cavity length increases. This indicates that we can optimize our design and maintain a thin profile by tuning the cavity length to achieve broadband absorption at low frequencies, while also reducing the reflectivity of ceramic tiled walls.
Oblique Incident Absorption Performance
We fix an optimal set of geometry parameters as mm, cm and cm, and study the effect of the incident wave angle on the sound absorption coefficient. The results in Figure 5(a) demonstrate that the optimized ceramic metatile wall achieves consistently high sound absorption over a wide range of incidence angles. In particular, it maintains absorption values exceeding 0.9 for incidence angles between , clearly outperforming conventional acoustic absorbers, as depicted in Figure 5(b).

Figure 5. (a) Absorption performance of oblique incident waves. (b) Absorption coefficient at 700 Hz as a function of the incidence angle.
Locally resonator absorbers are characterized by surface impedance that are independent of the incident angle. This simplified behavior can effectively model various types of absorbers, including quarter-wavelength and Helmholtz resonators (tuning cavities), as implemented in our work. However, when such materials are optimized for peak performance at grazing incidence, their absorption efficiency tends to decline at lower angles due to the strong angular dependence of the radiation impedance.
Experimental Verifications
The results from sound absorption testing are shown in Figure 6, where we observe a high degree of consistency with the acoustic absorption coefficient predicted by FEM and the analytical model. This close agreement confirms the reliability of the FEM and analytical approaches in accurately capturing the acoustic absorptive behavior of the ceramic metatile cavity structure. The band sound absorbing structure demonstrates excellent performance within the frequency range of 480 Hz to 700 Hz. Remarkably, even with a single tuning cavity defined by the geometric parameters mm, cm, and cm, the structure achieves strong sound absorption in this frequency range, with an average absorption coefficient exceeding 0.7 and reaching up to 1, thereby achieving quasi-perfect sound wave absorption. The minor discrepancies observed between the experimental and numerical results are attributed to fabrication imperfections, such as dimensional tolerances and surface roughness. Additionally, peaks appearing beyond 1000 Hz are likely due to diffraction phenomena caused by the finite size of the sample. It is worth noting that the tested sample measured 6.9 cm 6.9 cm, closely matching the 7 cm 7 cm cross-section of the impedance tube used in the measurements.

Figure 6. Absorption coefficients of the metatile obtained through experimental measurements, FEM numerical simulations, and analytical modeling.
Coupling of multiple cavities
After validating our numerical model with experimental results, we proceed to study the effect of coupling multiple cavities to open a broadband acoustic band gap at low frequencies. It is important to recall that our ceramic metatile design primarily targets thin wall applications. To preserve the aesthetic appearance of ceramic-tiled walls, we keep the slit width fixed at 1 cm, along with the neck dimensions. To explore the effect of cavity depth, we vary the parameter from 1 cm up to 28 cm, considering that standard ceramic tiles can reach up to 30 cm in thickness, thus enabling the formation of deep cavities behind the tiles. The findings of this study are presented in Figure 7. The results show that coupling large cavities of 28 cm with smaller ones as shallow as 1 cm can effectively generate broadband sound absorption within the frequency range of 200 Hz to 1000 Hz. This performance is notably superior compared to existing designs in the literature, achieving excellent absorption while maintaining a thin profile and preserving the visual appeal of ceramic-tiled walls.

Figure 7. Absorption coefficients of the ceramic metatile cavity obtained from FEM numerical simulations for multiple tuning cavities with varying cavity lengths ranging from 1 cm to 28 cm.
Building on the understanding that varying the cavity length can enhance sound absorption while maintaining a thin design using reflective ceramic tiles, we design a superlattice composed of multiple tuning cavities with different lengths. This super-lattice consists of 6 unit cells, each with the same slit width mm and cavity width cm, while the cavity length varies across the cells, the geometrical parameters are based on a previous study and are selected to achieve low-frequency broadband sound absorption. The parameter takes values of 14 cm, 16 cm, 17 cm, 18 cm, 19 cm, and 20 cm, with fixed at 30 cm. The corresponding frequencies, calculated using the expression:
are approximately 425 Hz, 398 Hz, 386 Hz, 375 Hz, 365 Hz, and 350 Hz, respectively. The goal is to achieve broadband sound absorption at low frequencies and demonstrate that modifying the cavity volumes within ceramic metatile walls significantly affects the absorption range, making these walls more acoustically absorptive despite being made of reflective ceramic materials. This concept is related to the well-known rainbow trapping phenomenon in acoustic metamaterials [38]. In our study, we refer this mechanism to show that it is possible to achieve low-frequency absorption simply by varying cavity lengths while preserving the thin form factor and aesthetic of ceramic-tiled walls, as presented in Figure 8.

Figure 8. Rainbow trapping sound absorption in the supercell composed of ceramic metatile cavities. (a) Absorption coefficient as a function of frequency, with colored zones indicating the most common indoor noise frequency ranges. (b) Acoustic pressure field screenshots of the cross-section -plane within the supercell structure. The parameter b takes values of 14 cm (425 Hz), 16 cm (398 Hz), 17 cm (386 Hz), 18 cm (375 Hz), 19 cm (365), and 20 cm (350 Hz), with l fixed at 30 cm.
By increasing the parameter , broadband sound absorption can be achieved in the frequency range of approximately 123 Hz to 744 Hz, as shown in Figure 8(a). When 6 thin cavities are assembled into a single superlattice, the largest cavity produces a strong resonance peak around 140 Hz, where the absorption coefficient reaches a value of 1. Following this peak, the absorption decreases slightly as additional cavities begin to activate, as illustrated in Figure 8(b). The absorption remains effective up to around 740 Hz, after which it returns to a more typical level once all cavities have been excited.
These results indicate that arranging ceramic metatiles to create a linear variation in cavity volume effectively reduces sound reflection by achieving absorption coefficients of 0.7 or higher over a broad frequency band ranging from 140 Hz to 744 Hz.
To summarize, we have demonstrated the effectiveness of incorporating tuning cavities into ceramic tile walls to enhance their acoustic performance.
This approach significantly enhances the tiles’ ability to absorb noise commonly generated in indoor environments, such as footsteps (typically 30 Hz to 470 Hz), musician instruments (like guitar within 140 Hz to 740 Hz) and sounds from household appliances typically occurring within the 80 Hz to 1000 Hz frequency range [39, 40], which are usually reflected by conventional tiled surfaces. Our findings show that low-frequency noise can be efficiently absorbed by simply adjusting the volume of the cavity. While our study focused on a configuration with six cavities, real-world applications could involve a larger number of cavities with lengths varying from 1 cm to 28 cm, as illustrated in Figure 7. Moreover, we emphasize that our design maintains a slim profile, with each cavity having a width of only 1 cm, an important consideration for practical use in building applications where space efficiency is critical.
Conclusion
To conclude, we analytically, numerically, and experimentally demonstrated the effectiveness of the proposed physical mechanism and its significantly added value compared to previous studies on ceramic tiled walls. First, we highlighted the acoustic performance of ceramic metatile walls by investigating the effect of cavity tuning. In particular, we introduced an acoustic metamaterial based on a Helmholtz resonator capable of achieving near-perfect absorption when integrated into a ceramic tiled wall. We showed that increasing the cavity length shifts the absorption peaks to lower frequencies, while increasing the neck thickness of the Helmholtz resonator shifts the peaks to higher frequencies and reduces the absorption coefficient. Furthermore, the structure maintains its sound absorption behavior even under oblique incidence of acoustic waves. Finally, we demonstrated the effectiveness of rainbow trapping in ceramic metatile cavities, enabling broadband and low-frequency sound absorption. The findings of this study open a new avenue for research on ceramic-tiled surfaces, particularly tiled walls which typically suffer from high sound reflectivity.
Acknowledgments
This research was funded by IRIS, BTU Trust, MetaMAT Ltd UK, the French ANR (contract "ANR-21-CE33-0015") and the European Union under Marie Skłodowska-Curie Actions Postdoctoral Fellowships (No. 101149710). The authors acknowledge the support of the French-Swiss SMYLE Network. We thank Julien Joly (Université Marie et Louis Pasteur, département d’Electronique) for the 3D printed structures.
References
- [1]S. Fengshan, L. Lijun, G. Xianyue, J. Xuejian, and D. Xiangjun, Equivalent model of spatial random array vibration system on sound-absorbing computing for porous material, Applied Acoustics 165, 107299 (2020).
- [2]S. Dong, Y. Duan, X. Chen, F. You, X. Jiang, D. Wang, D. Hu, and P. Zhao, Recent advances in preparation and structure of polyurethane porous materials for sound absorbing application, Macromolecular Rapid Communications 45, 2400108 (2024).DOI
- [3]J. Ning, S. Ren, and G. Zhao, Acoustic properties of micro-perforated panel absorber having arbitrary cross-sectional perforations, Applied Acoustics 111, 135 (2016).DOI
- [4]Z. Laly, N. Atalla, S.-A. Meslioui, and K. El Bikri, Sensitivity analysis of micro-perforated panel absorber models at high sound pressure levels, Applied Acoustics 156, 7 (2019).DOI
- [5]Z. Ren, Y. Cheng, M. Chen, X. Yuan, and D. Fang, A compact multifunctional metastructure for low-frequency broadband sound absorption and crash energy dissipation, Materials & Design 215, 110462 (2022).DOI
- [6]J. Li, W. Wang, Y. Xie, B.-I. Popa, and S. A. Cummer, A sound absorbing metasurface with coupled resonators, Applied Physics Letters 109 (2016).
- [7]K. Wang, Y. Chen, M. Kadic, C. Wang, and M. Wegener, Nonlocal interaction engineering of 2d rot on-like dispersion relations in acoustic and mechanical metamaterials, Communications Materials 3, 35 (2022).DOI
- [8]R. V. Craster, S. R. Guenneau, K. Muamer, and M. Wegener, Mechanical metamaterials, Reports on Progress in Physics (2023).DOI
- [9]B. Huang, Q. Miao, X. Zuo, J. Yi, Y. Zhou, and X. Luo, Sound absorption performance and mechanism of aluminum foam with double-layer structures of conventional and porous cell walls, Applied Acoustics 222, 110054 (2024).DOI
- [10]J. A. Iglesias Martínez, J. Moughames, G. Ulliac, M. Kadic, and V. Laude, Three-dimensional phononic crystal with ultra-wide bandgap at megahertz frequencies, Applied Physics Letters 118 (2021).DOI
- [11]N. Gao, J. Liu, J. Deng, D. Chen, Q. Huang, and G. Pan, Design and performance of ultra-broadband composite meta-absorber in the 200hz-20khz range, Journal of Sound and Vibration 574, 118229 (2024).DOI
- [12]Q. Ji, X. Chen, J. Liang, V. Laude, S. Guenneau, G. Fang, and M. Kadic, Designing thermal energy harvesting devices with natural materials through optimized microstructures, International Journal of Heat and Mass Transfer 169, 120948 (2021).arxiv.org/abs/2008.08928
- [13]M. Kadic, T. Bückmann, R. Schittny, and M. Wegener, Experiments on cloaking in optics, thermodynamics and mechanics, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences 373, 20140357 (2015).DOI
- [14]S. A. Cummer and D. Schurig, One path to acoustic cloaking, New journal of physics 9, 45 (2007).DOI
- [15]H. Chen and C. T. Chan, Acoustic cloaking in three dimensions using acoustic metamaterials, Applied physics letters 91 (2007).DOI
- [16]X.-Y. Chong, A.-L. Chen, X.-Y. Du, S.-D. Zhao, and Y.-S. Wang, Design of the reconfigurable rotationally symmetric resonant functional unit and curved metasurface for acoustic wavefront modulation, Composite Structures , 118873 (2025).DOI
- [17]Y. Chen, X. Wen, Y. Lu, Z. Lan, L. Fan, H. S. Park, Z. Gu, J. Zhu, and Z. Su, Broadband large-scale acoustic topological waveguides, Composite Structures 352, 118669 (2025).DOI
- [18]N. Kaina, F. Lemoult, M. Fink, and G. Leros ey, Negative refractive index and acoustic superlens from multiple scattering in single negative metamaterials, Nature 525, 77 (2015).DOI
- [19]C. Dong, J. Gu, Z. Liu, R. S. Pierce, J. Yang, X. Liu, and X. Yi, A novel membrane-coupled foldable metamaterial with low frequency sound absorption and vibration isolation performance, Composite Structures , 119314 (2025).DOI
- [20]H.-Z. Li, X.-C. Liu, Q. Liu, S. Li, J.-S. Yang, L.-L. Tong, S.-B. Shi, R. Schmidt, and K.-U. Schröder, Sound insulation performance of double membrane-type acoustic metamaterials combined with a helmholtz resonator, Applied Acoustics 205, 109297 (2023).DOI
- [21]D. M. Garza-Agudelo, V. C. Henriquez, C.-H. Jeong, P. R. Andersen, M. Ibarias, J. Sanchez-Dehesa, and F. Lucklum, Metasurfaces for sound absorption over a broad range of wave incidence angles, Applied Acoustics 220, 109965 (2024).DOI
- [22]B. Lemkalli, Z. E. A. Fellah, S. Guenneau, K. Lamzoud, A. Mir, and Y. Achaoui, Bi-functional metamaterial based on helmholtz resonators for sound and heat insulation, arXiv preprint arXiv:2310.05098 (2023).arxiv.org/abs/2310.05098
- [23]B. Lemkalli, M. Idrissi, A. Mir, and Y. Achaoui, Lightweight panels based on helmholtz resonators for low-frequency acoustic insulation, in E3S Web of Conferences, Vol. 469 (EDP Sciences, 2023) p. 00042.
- [24]J.-P. Groby, Ultra-thin metamaterial for perfect and quasi-omnidirectional sound absorption, Applied Physics Letters 109 (2016).DOI
- [25]G. d. N. Almeida, E. F. Vergara, L. R. Barbosa, and R. Brum, Low-frequency sound absorption of a metamaterial with symmetrical-coiled-up spaces, Applied Acoustics 172, 107593 (2021).
- [26]P. Sun, S. Xu, X. Wang, L. Gu, X. Luo, C. Zhao, and Z. Huang, Sound absorption of space-coiled metamaterials with soft walls, International Journal of Mechanical Sciences 261, 108696 (2024).DOI
- [27]T. Yuan, X. Song, J. Xu, B. Pan, D. Sui, H. Xiao, and J. Zhou, Tunable acoustic composite metasurface based porous material for broadband sound absorption, Composite Structures 298, 116014 (2022).DOI
- [28]S. Huang, G. Wen, S. Yin, Z. Lv, J. Liu, Z. Pan, and L. Jian, Tunable acoustic metasurface for broadband asymmetric focusing based on helmholtz resonator, Journal of Sound and Vibration 591, 118628 (2024).DOI
- [29]B. Lemkalli, S. Bensallam, M. Kadic, S. Guenneau, H. Jakjoud, A. Mir, and Y. Achaoui, An innovative clay metabrick-based motif to enhance thermal and acoustic insulation, arXiv preprint arXiv:2310.05148 (2023).DOI
- [30]X. Zhou, W. Zhang, X. Geng, and F. Xin, Broadband sound absorption of micro-perforated sandwich panels with hierarchical honeycomb core at high sound pressure levels, Composite Structures 354, 118794 (2025).DOI
- [31]D. Chen, K. Gao, J. Yang, and L. Zhang, Functionally graded porous structures: analyses, performances, and applications–a review, Thin-Walled Structures 191, 111046 (2023).DOI
- [32]A. M. Berto, Ceramic tiles: Above and beyond traditional applications, Journal of the European Ceramic Society 27, 1607 (2007).DOI
- [33]E. Sudol, M. Małek, M. Jackowski, M. Czarnecki, and C. Stręk, What makes a floor slippery? a brief experimental study of ceramic tiles slip resistance depending on their properties and surface conditions, Materials 14, 7064 (2021).DOI
- [34]S. V. Lenz, S. Guenneau, B. W. Drinkwater, R. V. Craster, and M. W. Holderied, Transformation twinning to create isospectral cavities, Physical Review B 108, 064209 (2023).arxiv.org/abs/2209.03810
- [35]S. Cominelli, B. Vial, S. Guenneau, and R. V. Craster, Isospectral open cavities and gratings, Proceedings of the Royal Society A 480, 20230853 (2024).
- [36]H. Baali, M. Addouche, A. Bouzerdoum, and A. Khelif, Design of acoustic absorbing metasurfaces using a data-driven approach, Communications Materials 4, 40 (2023).DOI
- [37]B. Lemkalli, O. T. Tugut, Q. Ji, R. Craster, S. Guenneau, M. Kadic, C. Bizzaglia, and B. Ungureanu, Controlling impact noise propagation with ceramic metatiles, arXiv preprint arXiv:2503.16682 (2025).
- [38]N. Jiménez, V. Romero-García, V. Pagneux, and J.-P. Groby, Rainbow-trapping absorbers: Broadband, perfect and asymmetric sound absorption by subwavelength panels for transmission problems, Scientific reports 7, 13595 (2017).DOI
- [39]X. Li, R. J. Logan, and R. E. Pastore, Perception of acoustic source characteristics: Walking sounds, The Journal of the Acoustical Society of America 90, 3036 (1991).pubmed.ncbi.nlm.nih.gov/1787243
- [40]S. Serafin, L. Turchet, and R. Nordahl, Extraction of ground reaction forces for real-time synthesis of walking sounds, in Proceedings of the 2009 Audio Mostly Conference (Glasgow Caledonian University, 2009) pp. 99–105.