betaFeedback

WorksPhysics and Astronomy

Depth-Resolved Lattice Distortions in a Silicon-Germanium Qubit Host

Abstract

Semiconductor qubits, promising for quantum computation, inherit properties from their host lattice. Quantum dot spins, occupying the local lowest energy states in the conduction band, necessarily couple to structural disorder and interfaces. While silicon-based systems promise low noise alongside industrially compatible manufacturing, the growth of SiGe—a leading platform—unavoidably introduces lattice dislocations, inhomogeneous strain, and crosshatch patterns, expected to cause fluctuations between devices, qubit failure, and subsequently higher operational overhead. Through X-ray nano-structural mapping of an Intel Si/SiGe chip, we reveal, with 30 ~nm lateral and 200 ~nm functional depth resolution, how extended lattice defects introduced during growth propagate through the heterostructure, creating permanently distorted lattice planes and strain. We correlate these at the ≈1 μ\approx1~μm scale of a quantum dot device and calculate the impact on qubit energy spectra. We observe crosshatch fine structure and find that substrate miscut and growth correlate with the final crosshatch pattern.

Semiconductors host spatially localized spin qubits in many emerging quantum devices [1, 2, 3, 4, 5, 6, 7, 8]. Silicon-based quantum dot (QD) systems in particular promise to combine decades of fabrication expertise with material properties such as a nuclear spin-free isotope and low spin-orbit coupling to realize low-noise, scalable qubits with sub-micron footprints [9, 10, 11, 12, 13, 14, 15, 17, 18] [16]. Gate-defined QD spin qubits, which rely on transistor-like fabrication on heterostructures to electrostatically trap single electrons, have demonstrated fault tolerant-compatible fidelities [19, 20, 21] in industrially manufactured devices with multiple qubit encodings [13, 22]. These systems are formed in a two-dimensional electron gas at the conduction band minimum of the host material, such that qubit energy levels are directly determined by the local band structure of the host, and are thus sensitive to the local crystal structure [1, 23, 24, 25, 26, 27, 28, 29, 30, 31].

Strained silicon quantum wells in alloyed silicon germanium (ϵSi\epsilon_{\mathrm{Si}}/SiGe) offer the high electron mobility and low spin noise suitable for forming QD spin qubits [9, 32]. However, the same lattice constant mismatch that contributes to a deep potential well in the ϵSi\epsilon_{\mathrm{Si}}, where the qubit resides, also poses challenges for the integration of SiGe with Si substrates necessary to produce devices. Epitaxy of SiGe on Si necessarily introduces dislocations to alleviate the lattice mismatch [32, 33, 34]. While current approaches partly mitigate dislocations through graded SiGe buffer layers—where Ge is increasingly introduced throughout microns of growth—the heterostructures nonetheless present a so-called crosshatch pattern (CHP): buckling of the lattice planes, observed as surface height variation or lattice plane tilt, resulting from

dislocation bundles forming along the SiGe {111}\{111\} slip planes [31, 35, 36]. The CHP leads to inhomogeneity in strain and lattice tilt, which distorts the crystal and thus the emergent QD qubits [31, 36].

Nanoscale X-ray diffraction microscopy (nXDM) [37, 38] provides a tool to measure the lattice distortions inside these heterostructure hosts at the lengthscale and sensitivity relevant to quantum devices. Previous nXDM SiGe quantum dot heterostructure work has studied lattice tilt in the quantum well [39], electrode-induced stress and curvature [40], composition heterogeneity [41], and the full strain tensor [42, 43]. These complement atomic force and Raman microscopies [31, 36, 44, 45], as well as single-qubit spectroscopy [23, 46] that probes low-energy excitations. In this work, we image an industrially manufactured Si/SiGe device from Intel (Tunnel Falls) with sub-micron lateral (30 nm) and, for the first time to our knowledge, depth (200 nm, extracted through analysis) spatial resolution. We reveal how lattice strain and CHP tilt arise during heterostructure growth, correlate with one another, and impact the ϵSi\epsilon_{\mathrm{Si}} quantum well (QW) qubit host. We first describe the nXDM experiment, focusing on the depth-resolved diffraction enabled by the graded SiGe buffer layer. We then use this functional depth resolution to study the emergence of CHP through the graded buffer. Through high-resolution imaging around a qubit device we correlate strain and CHP, as well as reveal fine structure in the CHP. Finally, we present calculations quantitatively relating the measured lattice strain and tilt to properties of the quantum well—energy fluctuations and atomic step density—that are expected to affect qubit operation. Taken together, this study links qubit host growth with qubit performance in order to guide future development of heterostructures and devices.

We employ the X-ray nanoprobe depicted in Figure 1(a) to study the Si/SiGe heterostructure shown schematically in Figure 1(b). nXDM is performed at room temperature by focusing a collimated 9.5 keV X-ray beam to a 30 nm spot size at the Si/SiGe 004 Bragg condition. As this beam is scanned around the region of interest, a Pixelated X-ray Photon Detector collects the entire diffraction pattern with 0.009° angular resolution, as in the inset, where the characteristic donut shapes result from the Fresnel Zone Plate. The diffraction signal maps out the local lattice vector in the sample—the lattice constant, strain, and lattice rotation all deflect the outgoing X-ray beam and are thus captured in the diffraction signal. The Fluorescence Detector collects X-ray fluorescence, providing a spatial map of patterned features. The narrowly focused beam has a depth of focus much larger than the heterostructure, such that the diffraction volume encompasses the full depth of the heterostructure.

Figure 1. (a) Nanoscale X-ray diffraction microscopy (nXDM) of the 004 peak of the Si/SiGe heterostructure shown in (b), where the Pixelated X-ray Photon Detector maps the crystal diffraction and the Fluorescence Detector maps material composition. Detector images show example diffraction signal of the heterostructure and fluorescence from the qubit device electrodes. The scanning XX (transverse to beam path) and YY directions are ≈3∘\approx3^\circ to the [110][110] and [11ˉ0][1\bar{1}0] crystal axes, due to sample mounting. All measurements are performed at room temperature. (b) Schematic of SiGe/Si/SiGe/Si heterostructure under study (not to scale). Labels at left correspond to features in diffraction (c,d). (c) Parallel beam diffraction signal with labeled features: (i) Si substrate, (ii) initial jump in growth to Si.93Ge.07\mathrm{Si}_{.93}\mathrm{Ge}_{.07}, (iii) graded buffer up to Si.81Ge.19\mathrm{Si}_{.81}\mathrm{Ge}_{.19}, (iv) kink at Si.81Ge.19\mathrm{Si}_{.81}\mathrm{Ge}_{.19}, where overall surface tilt is fixed, (v) graded buffer up to Si.69Ge.31\mathrm{Si}_{.69}\mathrm{Ge}_{.31}, (vi) Si.69Ge.31\mathrm{Si}_{.69}\mathrm{Ge}_{.31} virtual substrate, (viii) Si.69Ge.31\mathrm{Si}_{.69}\mathrm{Ge}_{.31} spacer atop quantum well. Inset: Focused beam diffraction at longer exposure, showing (vii) Si quantum well at expected tilt relative to the SiGe virtual substrate. (d) Summed detector signal showing correspondence between Δ2θ\Delta2\theta and [Ge] in the graded buffer, calculated assuming diffraction shift arises from the SiGe lattice constant and that the Si substrate is unstrained.

The heterostructure, produced by Intel for Tunnel Falls spin qubit processors, is designed to host a two-dimensional electron gas, and subsequently single electron quantum dots, in the quantum well formed by sandwiching a few-nanometer layer of ϵ\epsilonSi (vii, referencing the labels throughout Figure 1) between two layers of SiGe (vi, viii), inducing a large band offset in the Si [32]. Integrating high-Ge content SiGe (≈30%\approx30\%) with high-quality Si substrate wafers (i) requires the growth of a strain-relaxed buffer layer (ii–v) that increments the Ge concentration up to the desired concentration. Here, in the Tunnel Falls device, [Ge] increases linearly up to the so-called virtual substrate (vi) [12]. This layer is necessary to mitigate the strain and dislocations that arise from the lattice mismatch between Si and SiGe. However, as we show here, these features propagate through the SiGe growth and are present in the quantum well.

Figure 1(c) shows the parallel beam diffraction signal of the Si/SiGe. The axes are referenced to the Si substrate 004 peak assuming the substrate is unstrained. Corresponding to the schematic in Figure 1(b), we identify distinct signals from the Si substrate through the buffer layer, virtual substrate, and 50 nm SiGe cap layer, which is visible as a series of interference peaks. The signal from the thin quantum well (QW) is not visible here. Inset in Figure 1(c) is a long-exposure focused beam diffraction taken at larger incident angle where a component of the QW diffraction is visible around Δ2θ=1∘\Delta2\theta= 1^\circ. The total diffraction from the thin QW is spread out in Δ2θ\Delta2\theta, but is at comparable γ\gamma to the virtual substrate signal. In the Supplemental we extract the tilt of the QW along the studied qubit device and find it agrees with the tilt observed in the virtual substrate in Figure 4(c), confirming that the QW is epitaxial with the virtual substrate and justifying our assumption throughout this paper that the strain and lattice tilt measured in the virtual substrate are also present in the QW. Strain and lattice tilt throughout this work are extracted by defining “virtual detectors” over regions of interest in the diffraction signals of scanning tilt series, where the sample angle is rocked, described in the Supplemental.

Strain, conduction band minimum shift, gradient, and line cuts surrounding the qubit device

Figure 4. (a-c) c-axis strain εzz\varepsilon_{zz} and proportional conduction band minimum shift ΔEC\Delta E_C at three lengthscales surrounding the qubit device (DUT). White boxes show zoomed-in regions of subsequent figures and DUT. Measurement artifacts are visible from beam drops between Y=15Y = 15 µm to 50 µm in (a). The scale bar in (c) is shared with (a) and (b). (d) Magnitude of the gradient of ΔEC\Delta E_C, ∣∇EC∣\lvert\nabla E_C\rvert, zoomed in on the device. The spatial sampling (ΔX=39\Delta X = 39 nm, ΔY=13\Delta Y = 13 nm) in this image is small enough to fully sample the strain. (e,f) Line-cuts at various YY (XX) values of ΔEC\Delta E_C and ∣∇EC∣\lvert\nabla E_C\rvert. ∣∇EC∣\lvert\nabla E_C\rvert plots are offset by 25 µeV/µm for visibility.

The lattice constant-dependent diffraction combined with the [Ge]-dependent lattice constant enables functionally depth-resolved diffraction, circumventing the restriction of the large X-ray penetration depth, demonstrated in Figure 1(d). Figure 1(d) is the detector signal summed in γ\gamma with heterostructure features identified. The top axis shows the [Ge] at each Δ2θ\Delta2\theta angle, calculated from the lattice constant by inverting aSi1−xGex=0.027x2+0.2x+aSia_{\mathrm{Si}_{1-x}\mathrm{Ge}_x} = 0.027x^2 + 0.2x + a_{\mathrm{Si}} [47]. We ascribe the diffraction signal at a given Δ2θ\Delta2\theta to a depth in the graded buffer layer by comparing 1(e) to an independent measurement of [Ge] versus depth via secondary ion mass spectrometry (SIMS) for a similarly grown heterostructure.

The functionally depth-resolved diffraction allows the observation of lattice tilt throughout the graded buffer layer, providing insight into how substrate preparation and treatment impact tilt, and thus, as we demonstrate below in Figure 3, device strain. To spatially filter diffraction from a given lattice constant we form 5 pixel-wide virtual detectors in Δ2θ\Delta2\theta and extract θ\theta and γ\gamma angular tilts from the signal center-of-mass motion, resulting in ≈200\approx200 nm depth resolution, calculated from the associated [Ge]. γ\gamma corresponds to tilt about the [110][110] axis, oriented at a slight angle to the XX scanning axis, and θ\theta corresponds to tilt about the [11ˉ0][1\bar{1}0] axis, oriented at a slight angle to the YY scanning axis. We remove the arbitrary offset in each and then combine into Ω=γ2+θ2\Omega= \sqrt{\gamma^2 + \theta^2}, which captures the lattice plane slope regardless of direction. As γ\gamma and θ\theta are perpendicular, this effectively overlays the two into a single CHP. Figure 2(a-Figure 2c) show Ω\Omega tilt maps at three evenly spaced depths, referenced to the start of the virtual substrate and shown with corresponding [Ge]. Figure 2(a) is the start of SiGe growth at [Ge] = 7%; θ\theta tilt (vertical striations) is already visible, however there is minimal γ\gamma tilt (horizontal striations). This is consistent with an initial substrate miscut along [11ˉ0][1\bar{1}0], which we also observe through the gradual increase in average θ\theta in the diffraction signals in Figure 1. As the graded buffer grows, through Figure 2(b) and (c), θ\theta features remain relatively constant while γ\gamma features appear and propagate up to the virtual substrate, forming the final CHP. As the lattice tilts are a direct measure of the slope of the lattice planes, we integrate the tilt maps to reveal the spatial undulations of the lattice isosurfaces, shown in Figure 2(d-Figure 2f). New variations in the lattice isosurfaces appear as new tilt features arise.

Figure 2. Lattice tilt, Ω=γ2+θ2\Omega= \sqrt{\gamma^2 + \theta^2}, maps at the start of the buffer layer (a), partway through the buffer layer (b), and at the virtual substrate (c), calculated from five pixel-wide virtual detectors in Δ2θ\Delta2\theta, with (d-f) corresponding lattice iso-surface heights calculated by integrating the tilt. Scale bars are shared in each row. (g) Line-cuts of γ\gamma (horizontal striations in Ω\Omega) at all depths and two XX values, with the 1.2 μ\mum depth, corresponding to feature iv in Figure 1(c), bolded.

Figure 3. (a) γ\gamma and θ\theta tilt contours overlaid on X-ray fluorescence (XRF) of device electrodes, which define the active qubit region. (b,d) γ\gamma and θ\theta tilt contours (b) and κ\kappa curvature contours (d) overlaid on c-axis strain ϵzz\epsilon_{zz}. (c,e) Radially averaged cross-correlation CΩ,ϵzzC_{\Omega,\epsilon_{zz}} (c) and Cκ,ϵzzC_{\kappa,\epsilon_{zz}} (e) as a function of displacement ΔR\Delta R, fit empirically to a mono-exponential decay with decay length ℓC=820\ell_C = 820 nm to 880 nm. Shaded areas show one standard deviation from the radial averaging. (f,g) Fine-structure tilt maps θ~\tilde{\theta} and γ~\tilde{\gamma} after second-order polynomial background subtraction.

In Figure 2(g) we show line-cuts of Δγ=γ−γˉ\Delta\gamma= \gamma- \bar{\gamma} at two values of XX, with the line-cuts at a depth of 1.2 μ\mum bolded. This depth corresponds to the kink in the diffraction signal related to the surface tilt (Figure 1(c), feature iv). We observe at multiple locations, near X=−45X=-45 μ\mum, −30-30 μ\mum, 00 μ\mum, and 1010 μ\mum, a new tilt feature appears at this depth and propagates up to the virtual substrate, indicating a correlation between strain relaxation in the graded buffer and structural distortions in the virtual substrate.

In Figure 3 we further investigate the correlation between the lattice tilt Ω\Omega and curvature κ\kappa and cc-axis strain ϵzz\epsilon_{zz}, where κ=∣∂[θ,γ]∂[X,Y]∣\kappa= \left|\frac{\partial[\theta,\gamma]}{\partial[X,Y]}\right| is the Jacobian of the tilt. Figure 3(a) shows the lattice tilt contours measured in the virtual substrate overlaid on the X-ray fluorescence focused on a qubit device, with confining gate electrodes visible, which shape the 2D electron gas into qubit and sensor channels. The device is off-center in the image to ensure that the angled X-ray beam samples the virtual substrate, and thus can measure the strain, under the device. This particular device region sits at the corner of two intersecting perpendicular crosshatch features. We focus on this region to study strain-tilt correlation at a device-scale without interference of the large-scale crosshatch.

Figure 3(b) overlays contours of γ\gamma and θ\theta atop a ϵzz\epsilon_{zz} heatmap. Strain and tilt are studied quantitatively in Figure 4 and Figure 5; here we focus on spatial cross-correlations. Figure 3(c) shows the cross-correlation CΩ,ϵzz(ΔR)C_{\Omega,\epsilon_{zz}}(\Delta R) as a function of spatial displacement ΔR\Delta R, radially averaged over all angles out from zero displacement. Empirically fitting to a mono-exponential decay reveals a correlation decay length ℓC=820(10)\ell_C=820(10) nm with a maximum negative correlation of −0.55-0.55, showing that larger (smaller) lattice tilt is correlated with more negative, larger amplitude (less negative, smaller magnitude) strain. Performing the same analysis for curvature κ\kappa in Figure 3(d) and (e) reveals a similar correlation decay length of ℓC=880(10)\ell_C=880(10) nm and maximum positive correlation of 0.41. The existence of correlations with both Ω\Omega and κ\kappa confirm that CHP features, directly observed through the lattice distortion, have high curvature and tend to bundle strain, allowing for low-tilt, small-strain regions of the material.

Image not extracted

Figure 5. (a) As the strain relaxed buffer and virtual substrate grow, lattice tilt buckles the lattice planes (top). After polishing and re-growth, the quantum well intersects the truncated lattice planes, leading to finite step density at the well interface (bottom). (b) Atomic step density calculated from lattice tilt Ω\Omega.

The nanoscale spatial resolution reveals that these features are only correlated at <1< 1 μm. At this scale, in addition to the crosshatch tilt, there is finer tilt structure visible along the crosshatch slopes, shown as θ~\tilde{\theta} and γ~\tilde{\gamma} in Figure 3(f) and (g), respectively, by background subtracting a second-order polynomial from the device-scale tilt maps. This reveals features that otherwise are drowned out by the CHP, but likely contribute to strain relaxation nonetheless. The largest fine-structure tilt of 0.0046∘0.0046^\circ is a slope of 0.80.8 Å/11 μm.

We now study the impact of strain on the emergent energy landscape of QD spin qubits. In Figure 4(a-Figure 4c) we show the c-axis strain ϵzz\epsilon_{zz} in the virtual substrate, and thus the QW, and the resulting proportional shift to the conduction band minimum energy ΔEC\Delta E_C, at three lengthscales of (100 μm)2(100\ \mathrm{\mu m})^2 (a), (10 μm)2(10\ \mathrm{\mu m})^2 (b), and 4 μm×2 μm4\ \mathrm{\mu m}\times2\ \mathrm{\mu m} (c), focused on the qubit device. The colorbar in (c) is shared with (a,b). The labeled DUT refers to the qubit channel within the device shown in the Fluorescence Detector in Figure 1(b). ΔEC\Delta E_C is calculated as ξuϵzz+ξd(2ϵxx+ϵzz)\xi_u\epsilon_{zz}+\xi_d(2\epsilon_{xx}+\epsilon_{zz}), where ϵxx=ϵzz⋅s11+s122s11\epsilon_{xx}=\epsilon_{zz}\cdot\frac{s_{11}+s_{12}}{2s_{11}}, sijs_{ij} are components of the stiffness tensor, and ξu\xi_u, ξd\xi_d are deformation potentials [48]. Strain down to −5×10−4-5\times10^{-4} is present across the imaged region, with fine structure at both the μ\mum and sub-μ\mum scales. Strain in the QW directly affects the conduction band offset in the well, introducing shifts in a QD chemical potential, energy detuning between neighboring dots, and long-range energy fluctuations. These may affect qubit operation, in particular double-dot operations like exchange coupling, and electron shuttling, where electrons move over microns inside the QW. To further study this, we plot the gradient of the energy shift ∣∇EC∣\lvert\nabla E_C\rvert in Figure 4(d), with linecuts of ΔEC\Delta E_C and ∇EC\nabla E_C in Figure 4(e). While the gradient over the studied DUT is by chance low, we observe areas as high as 6868 μeV/μ\mum. As valley splitting energies in SiGe can be ≈100\approx100 μeV [23, 25, 29], this gradient corresponds to a change equal to the valley splitting energy over the length of a moderate-size device, and may impact shuttling fidelity [49].

In Figure 5 we study how lattice tilt results in atomic steps at the quantum well interface. Figure 5(a) shows schematically how atomic steps arise even with polishing during heterostructure growth. On the top is a set of lattice planes that are distorted by spatially varying lattice tilt. On the bottom, even if the surface is polished, the lattice tilt remains in place. When the Si quantum well is grown epitaxially atop the distorted SiGe lattice planes, the truncated planes intersect the well interface, causing atomic steps, plotted schematically above the quantum well. Figure 5(b) calculates the step density tan⁡(Ω)/a\tan(\Omega)/a from the tilt map. Regions where tilt is higher consequently have higher step density, up to 6.6 steps/μ\mum. At the scale of around 10 quantum dots, this corresponds to multiple dots intersected by atomic steps, which is known to significantly reduce valley splitting in the deterministic regime by a factor of 3-4 [24, 50, 51], although this is dependent on the orientation of the device.

We have demonstrated that spatially varying strain and lattice tilt, directly measured in nXDM, have the potential to impact the behavior of scaled-up quantum dot processors through their coupling to the qubit energy landscape. In the Supplemental we explore if strain and lattice tilt correlate in this specific device with valley splitting energy, characterized in Ref. [23]. We previously determined that the distribution of valley splitting was properly described by the alloy disorder in the engineered quantum well, and here do not find any relationship to the measured lattice distortions. However, this device was not designed to be specifically sensitive to strain and tilt, and there are multiple factors that could lead to our observations: the device sits in a relatively flat strain region; alloy disorder is large; and the quantum well interface is broad, obscuring effects of atomic steps. Ultimately, fully correlating heterostructure features with spin qubit properties will require cryogenic qubit characterization with scale and resolution comparable to nXDM, as in recent shuttling experiments [26, 27, 29, 52, 53].

Through functionally depth-resolved nXDM, sub-micron device-scale strain mapping, and theoretical calculations, we have shown how Si/SiGe heterostructure preparation and growth are expected to impact industrially manufactured qubit devices. The observed correlations between strain and tilt, consistent with the expected behavior of dislocation bundles, directly connect the evolution of lattice tilt to qubit energy fluctuations. While individual few-qubit devices can be situated in a low-strain, dislocation-free region of material, as devices scale to larger numbers and integrate components such as electron shuttlers, avoiding inhomogeneity in the host material will be unavoidable. This may motivate designing devices to avoid crosshatch features, or designing new growth approaches that guide dislocation bundles. Our measurements also provide a quantitative dataset on the heterostructure, at multiple scales, that will inform future device theory and modeling.

Acknowledgments

The authors thank Nathaniel C. Bishop, Joelle Corrigan, Eric Henry, and Nazar Delegan for useful discussion. Work was supported by the U.S. Department of Energy, Office of Science, National Quantum Information Science Research Centers as part of the Q-NEXT center. T.O. was supported by Netherlands Ministry of Defence under Award No. QuBits R23/009. Work performed at the Center for Nanoscale Materials and Advanced Photon Source on APS beam time award (DOI: 10.46936/APS191441/60015139), both U.S. Department of Energy Office of Science User Facilities, was supported by the U.S. DOE, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. The authors acknowledge Intel Corp. for providing the sample and SIMS data.

Author Contributions

J.C.M., M.A.E., and M.V.H. conceived of the study; J.C.M., E.S.J., J.R., T.Z., and M.V.H. performed measurements and analyzed data; T.O., A.P., and M.F. provided theory support; J.C.M. coordinated the project and prepared the manuscript with input from all authors.

Competing Interests

The authors declare no competing interests.

Supplementary Materials

Virtual detectors

Two-dimensional diffraction maps are acquired for each spatial position and every angle during a scan, and contain signals from the entire illuminated volumn. In order to acquire signal related to a specific spatial region and lattice feature we track the center-of-mass (COM) signal within user-defined virtual detectors, shown in Figure S1. Figure S1 shows four representative virtual detectors overlaid on the diffraction signal from one of the spatial scans. We first focus on the right-most feature, around 2θ=−0.75∘2\theta= -0.75^\circ, which corresponds to the virtual substrate. Multiple donut features are visible, arising from the spatially varying lattice tilt. By defining detectors i and ii we can track the γ\gamma tilt, as the signal donut will shift in accordance with γ\gamma. Detector iii similarly tracks changes in 2θ2\theta. Detector iv shows how we isolate the signal from a specific depth in the graded buffer layer. By picking a window at a specific 2θ2\theta, we effectively filter the signal from a specific lattice constant and thus, as shown in main text Figure 1, a specific depth. Figure S1 reproduces the quantum well detector image from Figure 1(d) with a virtual detector placed around the quantum well diffraction signal, used in Figure S2 to extract the quantum well tilt.

Figure S1. (a) Representative diffraction signal of heterostructure with virtual detector regions of interest defined. i and ii are sensitive to γ\gamma tilt, while iii is sensitive to θ\theta tilt. iv picks out a slice of the buffer layer, providing functional depth resolution. (b) Representative diffraction signal of quantum well, with virtual detector v defined around the QW diffraction feature.

Figure S2. Comparison of γ\gamma tilt along the qubit device extracted from the device-scale tilt map, the (10 μm)2(10\ \mu\mathrm{m})^2 tilt map, and the quantum well diffraction signal (Figure S1).

Quantum well tilt

In Figure S2 we compare the γ\gamma tilt of the quantum well, extracted from the virtual detector COM in Figure S1, with that of the device-scale and (10 μm)2(10\ \mu\mathrm{m})^2 virtual substrate tilt maps in main text Figure 4. We observe values in the virtual substrate tilt maps that match within 13% of the QW values and exhibit the same structure over the QW is epitaxial with the virtual substrate. We do not expect perfect agreement because (1) the virtual substrate signal is averaged over ≈1 μm\approx1\ \mu\mathrm{m} of material, while the quantum well is only 4.6 nm, and (2) the QW signal is affected by bleedthrough of background signal from the heterostructure diffraction, which can be seen in Figure S1.

Full depth dataset

In Figure S3 and Figure S4 we show the tilt and iso-surface height for each analyzed depth in Figure 2.

Figure S3. Full Ω\Omega tilt dataset for main text Figure 2 for each depth and [Ge] extracted from the full heterostructure diffraction.

Figure S4. Full iso-surface dataset for main text Fig. 2 for each depth and [Ge] extracted from the full heterostructure diffraction.

Spatial cross-correlation

In Figure 3 we analyze the spatial cross-correlation between tilt Ω\Omega, curvature κ\kappa, and strain ϵzz\epsilon_{zz}. Spatial maps from Figure 3 are reproduced in Figure S5,Figure S5). For two spatial maps AA and BB, we calculate the cross-correlation by centering about zero and normalizing each map

Figure S5. (a,b) γ\gamma, θ\theta and κ\kappa contours overlaid on εzz\varepsilon_{zz} maps, reproduced from main text Figure 3. (c,d) 2D spatial cross-correlation maps for Ω\Omega (c) and κ\kappa (d), where correlation is calculated between the two 2D arrays for each displacement (ΔX\Delta X, ΔY\Delta Y). Radially averaging over these maps produces the 1D cross-correlation in main text Figure 3.

A~=A−Aˉ∑(A−Aˉ)2(1)\widetilde{A} = \frac{A-\bar{A}}{\sqrt{\sum\left(A-\bar{A}\right)^2}} \tag*{(1)}
B~=B−Bˉ∑(B−Bˉ)2(2)\widetilde{B} = \frac{B-\bar{B}}{\sqrt{\sum\left(B-\bar{B}\right)^2}} \tag*{(2)}

Then we calculate the cross-correlation CC with the SciPy function

C = scipy.signal.correlate2d(A,B)

Comparison to valley splitting

We have previously measured the valley splitting with 60 nm resolution across the qubit channel of this device in Ref. [23]. We concluded that the observed wide and fast variation in valley splitting was completely explained by alloy disorder in the 2.8%-Ge Si quantum well. However, there was a possibility that the lattice distortion, which we have now measured through X-ray diffraction, could explain the origin of the valley splitting, as in recent work [31]. In Figure S6 we plot the previously measured valley splitting alongside the γ\gamma tilt (a), θ\theta tilt (b), curvature κ\kappa (c), and cc-axis strain ϵzz\epsilon_{zz} (d). No feature has the range or speed of variation to explain the dominant valley splitting fluctuations, supporting our initial conclusion about the role of alloy disorder.

Figure S6. Comparison of valley splitting EVE_V to lattice deformation: (a) γ\gamma, (b) θ\theta, (c) κ\kappa, and (d) εzz\varepsilon_{zz}.

References

  1. [1]G. Burkard, T. D. Ladd, A. Pan, J. M. Nichol, and J. R. Petta, Semiconductor spin qubits, Rev. Mod. Phys. 95, 025003 (2023).DOI
  2. [2]A. Chatterjee, P. Stevenson, S. De Franceschi, A. Morello, N. P. De Leon, and F. K. Kummeth, Semiconductor qubits in practice, Nat. Rev. Phys. 3, 157 (2021).DOI
  3. [3]G. Scappucci, C. Kloeffel, F. A. Zwanenburg, D. Loss, M. Myronov, J.-J. Zhang, S. De Franceschi, G. Katsaros, and M. Veldhorst, The germanium quantum information route, Nat. Rev. Mater. 6, 926 (2021).DOI
  4. [4]L. M. K. Vandersypen, H. Bluhm, J. S. Clarke, A. S. Dzurak, R. Ishihara, A. Morello, D. J. Reilly, L. R. Schreiber, and M. Veldhorst, Interfacing spin qubits in quantum dots and donors—hot, dense, and coherent, npj Quantum Inf. 3, 1 (2017).
  5. [5]G. Wolfowicz, F. J. Heremans, C. P. Anderson, S. Kanai, H. Seo, A. Gali, G. Galli, and D. D. Awschalom, Quantum guidelines for solid-state spin defects, Nat. Rev. Mater. 6, 906 (2021).
  6. [6]N. P. de Leon, K. M. Itoh, D. Kim, K. K. Mehta, T. E. Northup, H. Paik, B. S. Palmer, N. Samarth, S. Sangtawesin, and D. W. Steuerman, Materials challenges and opportunities for quantum computing hardware, Science 372, eabb2823 (2021).
  7. [7]D. D. Awschalom, R. Hanson, J. Wrachtrup, and B. B. Zhou, Quantum technologies with optically interfaced solid-state spins, Nat. Photonics 12, 516 (2018).
  8. [8]J. C. Marks, B. Pingault, J. Zhang, C. Zeledon, F. J. Heremans, and D. D. Awschalom, Nuclear spin engineering for quantum information science, J. Mater. Res. 40, 1433 (2025).
  9. [9]M. A. Eriksson, M. Friesen, S. N. Coppersmith, R. Joynt, L. J. Klein, K. Slinker, C. Tahan, P. M. Mooney, J. O. Chu, and S. J. Koester, Spin-Based Quantum Dot Quantum Computing in Silicon, Quantum Inf. Process. 3, 133 (2004).
  10. [10]A. M. J. Zwerver, T. Krähenmann, T. F. Watson, L. Lampert, H. C. George, R. Pillarisetty, S. A. Bojarski, P. Amin, S. V. Amonov, J. M. Boter, R. Caudillo, D. Correas-Serrano, J. P. Dehollain, G. Droulers, E. M. Henry, R. Kotlyar, M. Lodari, F. Lüthi, D. J. Michalak, B. K. Mueller, S. Neyens, J. Roberts, N. Samkharadze, G. Zheng, O. K. Zietz, G. Scappucci, M. Veldhorst, L. M. K. Vandersypen, and J. S. Clarke, Qubits made by advanced semiconductor manufacturing, Nat. Electron. 5, 184 (2022).DOI
  11. [11]S. Neyens, O. K. Zietz, T. F. Watson, F. Lüthi, A. Nethwawala, H. C. George, E. Henry, M. Islam, A. J. Wagner, F. Borjans, E. J. Connors, J. Corrigan, M. J. Curry, D. Keith, R. Kotlyar, L. F. Lampert, M. T. Mądzik, K. Millard, F. A. Mohiyaddin, S. Pellerano, R. Pillarisetty, M. Ramsey, R. Savytskyy, S. Schaal, G. Zheng, J. Ziegler, N. C. Bishop, S. Bojarski, J. Roberts, and J. S. Clarke, Probing single electrons across 300-mm spin qubit wafers, Nature 629, 80 (2024).
  12. [12]H. C. George, M. T. Mądzik, E. M. Henry, A. J. Wagner, M. M. Islam, F. Borjans, E. J. Connors, J. Corrigan, M. Curry, M. K. Harper, D. Keith, L. Lampert, F. Lüthi, F. A. Mohiyaddin, S. Murcia, R. Nair, R. Nahm, A. Nethwawala, S. Neyens, B. Patra, R. D. Raharjo, C. Rogan, R. Savytskyy, T. F. Watson, J. Ziegler, O. K. Zietz, S. Pellerano, R. Pillarisetty, N. C. Bishop, S. A. Bojarski, J. Roberts, and J. S. Clarke, 12-Spin-Qubit Arrays Fabricated on a 300 mm Semiconductor Manufacturing Line, Nano Lett. 25, 793 (2025).
  13. [13]P. Steinacker, N. Dumoulin Stuyck, W. H. Lim, T. Tantu, M. Feng, S. Serrano, A. Nickl, M. Candido, J. D. Cifuentes, E. Vahapoglu, S. K. Bartee, F. E. Hudson, K. W. Chan, S. K. Kubicek, J. Jussot, Y. Canvel, S. Beyne, Y. Shimura, R. Loo, C. Godfrin, B. Raes, S. Baudot, D. Wan, A. Laucht, C. H. Yang, A. Saraiva, C. C. Escott, K. De Greve, and A. S. Dzurak, Industry-compatible silicon spin-qubit unit cells exceeding 99% fidelity, Nature 646, 10.1038/s41586-025-09531-9 (2025).
  14. [14]A. Elsayed, M. M. K. Shehata, C. Godfrin, S. Kubicek, S. Massar, Y. Canvel, J. Jussot, G. Simion, M. Mongillo, D. Wan, B. Govoreanu, I. P. Radu, R. Li, P. Van Dorpe, and K. De Greve, Low charge noise quantum dots with industrial CMOS manufacturing, npj Quantum Inf. 10, 1 (2024).
  15. [15]P. Tomić, P. Bütler, Y. Wu, B. Raes, C. Godfrin, S. Kubicek, J. Jussot, Y. Canvel, Y. Hermans, Y. Shimura, R. Loo, S. Beyne, G. Jaliel, T. V. Caekenberghe, V. Levajac, D. Wan, K. D. Greve, W. W. Huang, K. Ensslin, and T. Ihn, Long coherence silicon spin qubit fabricated in a 300 mm industrial foundry (2025), arXiv:2512.20758 [16] S. Beyne, S. Kubicek, C. Godfrin, B. Raes, T. Van Caekenberghe, J. De Backer, Y. Hermans, F. Treska, S. Kaushik, Y. Jiang, B. Chou, T. Sarkar, Y. Li, S. Sharma, S. Baudot, L. Pinotti, Y. Shimura, R. Loo, B. Kenens, J. Vande Weeghe, E. Vrancken, K. Vandersmissen, J. Mitard, K. Devriendt, D. Wan, and K. De Greve, 300mm fabrication of silicon quantum dot spin qubits using 0.33NA EUV lithography, in 2025 IEEE International Electron Devices Meeting (IEDM) (2025) pp. 1–4.
  16. [17]T. Koch, C. Godfrin, V. Adam, J. Ferrero, D. Schroller, N. Glaeser, S. Kubicek, R. Li, R. Loo, S. Massar, G. Simion, D. Wan, K. De Greve, and W. Wernsdorfer, Industrial 300 mm wafer processed spin qubits in natural silicon/silicon-germanium, npj Quantum Inf. 11, 59 (2025).arxiv.org/abs/2409.12731
  17. [18]M. T. Mąd zik, F. Luthi, G. G. Guerreschi, F. A. Mohiyaddin, F. Borjans, J. D. Chadwick, M. J. Curry, J. Ziegler, S. Atanasov, P. L. Bavdaz, E. J. Connors, J. Corrigan, H. E. Ercan, R. Flory, H. C. George, B. Harpt, E. Henry, M. M. Islam, N. Khammassi, D. Keith, L. F. Lampert, T. M. Mladenov, R. W. Morris, A. Nethwewala, S. Neyens, R. Otten, L. P. Osuna Ibarra, B. Patra, R. Pillarisetty, S. Premaratne, M. Ramsey, A. Risinger, J. D. Rooney, R. Savitsky, T. F. Watson, O. K. Zietz, A. Y. Matsuura, S. Pellerano, N. C. Bishop, J. Roberts, and J. S. Clarke, Operating two exchange-only qubits in parallel, Nature 647, 870 (2025).DOI
  18. [19]A. Noiri, K. Takeda, T. Nakajima, T. Kobayashi, A. Sammak, G. Scappucci, and S. Tarucha, Fast universal quantum gate above the fault-tolerance threshold in silicon, Nature 601, 338 (2022).DOI
  19. [20]J. Z. Blumoff, A. S. Pan, T. E. Keating, R. W. Andrews, D. W. Barnes, T. L. Brecht, E. T. Croke, L. E. Euliss, J. A. Fast, C. A. Jackson, A. M. Jones, J. Kerckhoff, R. K. Lanza, K. Raach, B. J. Thomas, R. Velunta, A. J. Weinstein, T. D. Ladd, K. Eng, M. G. Borselli, A. T. Hunter, and M. T. Rakher, Fast and High-Fidelity State Preparation and Measurement in Triple-Quantum-Dot Spin Qubits, PRX Quantum 3, 010352 (2022).DOI
  20. [21]Y.-H. Wu, L. C. Camenzind, P. Büttler, I. K. Jin, A. Noiri, K. Takeda, T. Nakajima, T. Kobayashi, G. Scappucci, H.-S. Goan, and S. Tarucha, Simultaneous High-Fidelity Single-Qubit Gates in a Spin Qubit Array (2025), arXiv:2507.11918 [quant-ph].DOI
  21. [22]M. o. t. H. Q. Team, Collaborators, M. Abraham, E. Acuna, T. S. Adams, M. Akmal, M. R. Alfaro, I. Alvarado, J. Armentre, C. Andrews, R. W. Andrews, M. Antcliffe, A. R. Asêncio, R. M. A. Batres, C. D. Baringer, D. W. Barnes, K. M. Beech, R. G. Blakey, Z. T. Bloom, A. J. Bluestone, J. Z. Blumoff, M. G. Borselli, K. A. Bose, B. Boyd, J. T. Boyer, T. L. Brecht, C. C. Brough, R. A. Brown, S. L. Brown, T. A. Cain, J. B. Carpenter, S. Carr, F. W. Carter, M. Casanova, J. L. Chambers, M. D. Chambers, K. L. Chanthavong, J. M. Chappell, R. Chavez, K. C. Chen, P. S. Chen, M. D. Choi, K. Choudhary, M. N. H. Chow, J. E. Christensen, A. M. Chronister, A. M. Clapper, A. Coker, M. D. Cornelius, A. E. Cosand, I. T. Counts, E. T. Croke, G. M. Crosswhite, A. Dally, E. S. Daniel, T. A. Dao, D. Daprano, T. Davis, N. Deshpande, R. S. Dey, D. S. Diamond, C. E. Dickerson, J. P. Dodson, J. B. Dragan, M. Dvorak, L. F. Edge, C. R. Elliott, K. R. Elliott, K. Eng, J. East, C. P. Feeney, D. J. Fialkow, D. H. Finestone, M. N. Fireman, B. H. Fong, T. M. Fowler, S. Frazier, K. L. Fuller, C. A. C. Garcia, K. L. Garstka, K. C. Garvey, Z. A. Geiger, G. R. Gledhill, C. M. Goodwin-Schoen, J. L. Goralka, B. W. Greene, H. K. Gurgenian, S. D. Ha, W. Ha, N. R. Hapeman, B. M. Hardesty, J. W. Harrington, P. M. Harrington, T. R. B. Harris, B. M. Harrison, A. T. Hatke, R. R. Hayes, K. He, R. H. Garcia, R. M. Hickey, J. Hicks-Garner, A. Hirman, D. A. Hitko, D. Ho, H. Y. Ho, V. S. Ho, n. holman, A. Holmes, N. Huffman, D. R. Hulbert, E. B. Isaacs, C. A. C. Jackson, L. Jaeger, I. Jenkins, C. Jennings, P. C. Jerger, B. Johnson, A. M. Jones, M. P. Jura, A. V. Kabakian, R. M. Katti, T. Keating, J. Kerckhoff, J. D. Kern, I. Khalaf, A. Kher, J. J. Kim, E. W. Kinder, A. A. Kiselev, W. F. Koehl, P. W. Krantz, T. D. Ladd, P. G. Laing, S. Lakdawala, N. J. Lang, R. Lanzar, E. Lawson-Fox, D. Le, K. Lee, N. R. A. Lee, J. Lerma, M. P. Levendorf, A. R. Liu, H. Lizarraga, A. Lopez, H. C. Ly, T. T. Lyons, T. K. Macioce, M. M. Mackey, J. K. Maeda, R. M. Martin, D. S. Matic, J. W. Matten, G. C. Mazur, M. S. McCready, O. Means, K. E. Millner, I. Milosavljеvic, M. Morris, S. L. Morton, S. Mumford, B. D. Murley, R. G. Nagele, T. A. Naoi, C. R. Nelson, G. A. Newman, D. B. Nguyen, T. Niknejad, R. N. Nishide, L. C. O’Brien, C. B. E. O’Keefe, R. P. O’Neil, A. E. Oriani, A. F. Ortiz, J. J. Ottusch, A. Pan, P. R. Patterson, U. Paudel, J. C. Perez, C. A. Peterson, V. T. Phan, N. H. Pilgram, C. E. Plesha, W. Pouse, E. M. Prophet, D. R. Queen, N. Quirk, K. Raach, M. T. Rakher, M. D. Reed, B. D. Reynolds, L. D. Robertson, Z. Rogers, Y. Royter, M. J. Ruiz, G. Sabbir, R. Sajjad, C. D. Sanborn, R. H. Sarmiento, C. J. Schnable, C. Scott, N. M. Sebastian, E. M. Segall, A. Senanian, A. Sicairos, S. Siddiqui, K. Singh, A. Smith, D. E. Smith, R. S. Smith, S. F. Sontag, E. A. Sovero, K. C. Staley, A. Suu, J. Suh, B. Sun, D. Sun, C. M. Swank, N. Swimmer, M. J. Taboada, B. J. Thomas, Y. Torres, J. W. Touve, A. Tran, I. Tran, C. Tsen, S. Turner, M. Valencia, I. Valles, J. R. v. Meter, N. D. VanRensselaer, F. Vartanian, D. Yolya, Z. J. Vrba, P. H. Vu, A. L. Wagner, J. Wallner, M. P. Walsh, S. Wang, T. Wang, D. R. Ward, A. J. Weinstein, T. B. Welch, T. V. Westrick, E. T. White, R. M. White, S. J. Whiteley, G. Wijeratne, P. Williams, J. T. Wilson, C. P. Wilt, D. E. Winklea, O. Yaglioglu, D. Yap, C. S. YoungScortino, D. Zehnder, and A. Ziegler, A digitally controlled silicon quantum processing unit (2026), arXiv:2604.16216 [quant-ph] version: 2.
  22. [23]J. C. Marcks, F. Eagen, E. C. Brann, M. P. Losert, T. Oh, J. Reily, C. S. Wang, D. Keith, F. A. Mohiyaddin, F. Luthi, M. J. Curry, J. Zhang, F. J. Heremans, M. Friesen, and M. A. Eriksson, Valley splitting correlations across a silicon quantum well containing germanium, Nat. Commun. 16, 11381 (2025).DOI
  23. [24]M. P. Losert, M. A. Eriksson, R. Joynt, R. Rahman, G. Scappucci, S. N. Coppersmith, and M. Friesen, Practical strategies for enhancing the valley splitting in Si/SiGe quantum wells, Phys. Rev. B 108, 125405 (2023).DOI
  24. [25]J. P. Dodson, H. E. Ercan, J. Corrigan, M. P. Losert, N. Holman, T. McJunkin, L. F. Edge, M. Friesen, S. N. Coppersmith, and M. A. Eriksson, How Valley-Orbit States in Silicon Quantum Dots Probe Quantum Well Interfaces, Phys. Rev. Lett. 128, 146802 (2022).DOI
  25. [26]M. Volmer, T. Struck, A. Sala, J.-S. Tu, S. Trellenkamp, D. Degli Esposti, G. Scappucci, E. Cywiński, H. Bluhm, and L. R. Schreiber, Impact of the local valley splitting on the coherence of conveyor-belt spin shuttling in 28Si/SiGe, Nat. Commun. 17, 4548 (2026).DOI
  26. [27]M. Volmer, T. Struck, A. Sala, J.-S. Tu, S. Trellenkamp, D. D. Esposti, G. Scappucci, L. Cywiński, H. Bluhm, and L. R. Schreiber, Mapping g-factors and complex intervalley coupling in Si/SiGe by conveyor-mode shuttling (2026), arXiv:2603.01844 [quant-ph].arxiv.org/abs/2603.01844
  27. [28]J. Klos, J. Tröger, J. Keutgen, M. P. Losert, H. Riemann, N. V. Abrosimov, J. Knoch, H. Bracht, S. N. Coppersmith, M. Friesen, O. Cojocaru-Mirédin, L. R. Schreiber, and D. Bougeard, Atomistic compositional details and their importance for spin qubits in isotope-purified silicon-germanium quantum wells, arXiv:2405.19974 (2024).DOI
  28. [29]M. Volmer, T. Struck, A. Sala, B. Chen, M. Oberländer, T. Offermann, R. Xue, L. Visser, J.-S. Tu, S. Trellenkamp, L. Cywiński, H. Bluhm, and L. R. Schreiber, Mapping of valley splitting by conveyor-mode spin-coherent electron shuttling, npj Quantum Inf. 10, 1 (2024).DOI
  29. [30]B. Paquelet Wuetz, M. P. Losert, S. Koelling, L. E. A. Stehouwer, A.-M. J. Zwerver, S. G. J. Philips, M. T. Ma̧dzik, X. Xue, G. Zheng, M. Lodari, S. V. Amitonov, N. Samkharadze, A. Sammak, L. M. K. Vandersypen, R. Rahman, S. N. Coppersmith, O. Moutanabbir, M. Friesen, and G. Scappucci, Atomic fluctuations lifting the energy degeneracy in Si/SiGe quantum dots, Nat. Commun. 13, 7730 (2022).DOI
  30. [31]L. F. Peña, M. I. Brickson, F. Rovaris, J. H. Dycus, A. McDonald, Z. T. Piontkowski, J. B. Ruzinanda, A. M. Bradicich, D. Bethke, R. Scott, T. E. Beecham, F. Montalenti, N. T. Jacobson, and E. Bussmann, Cross-hatch strain effects on SiGe quantum dots for qubit variability estimation (2026).arxiv.org/abs/2601.05553
  31. [32]F. Schäffler, High-mobility Si and Ge structures, Semiconductor Sci. Technol. 12, 1515 (1997).DOI
  32. [33]P. M. Mooney, Strain relaxation and dislocations in SiGe/Si structures, Mater. Sci. Eng.: R: Rep. 17, 105 (1996).DOI
  33. [34]K. Sawano, S. Koh, Y. Shiraki, N. Usami, and K. Nakagawa, In-plane strain fluctuation in strained-Si/SiGe heterostructures, Appl. Phys. Lett. 83, 4339 (2003).DOI
  34. [35]E. A. Fitzgerald, Y.-H. Xie, M. L. Green, D. Brasen, A. R. Kortan, J. Michel, Y.-J. Mii, and B. E. Weir, Totally relaxed GeₓSi₁₋ₓ layers with low threading dislocation densities grown on Si substrates, Appl. Phys. Lett. 59, 811 (1991).DOI
  35. [36]D. Degli Esposti, L. E. A. Stehouwer, Ö. Gül, N. Samkharadze, C. Deprez, M. Meyer, I. N. Meijer, L. Tryputen, S. Karwal, M. Botifoll, J. Arbiol, S. V. Amitonov, L. M. K. Vandersypen, A. Sammak, M. Veldhorst, and G. Scappucci, Low disorder and high valley splitting in silicon, npj Quantum Inf. 10, 32 (2024).DOI
  36. [37]R. P. Winarski, M. V. Holt, V. Rose, P. Fuesz, D. Carbaugh, C. Benson, D. Shu, D. Kline, G. B. Stephenson, I. McNulty, and J. Maser, A hard X-ray nanoprobe beamline for nanoscale microscopy, J. Synchrotron Rad. 19, 1056 (2012).
  37. [38]M. Holt, R. Harder, R. Winarski, and V. Rose, Nanoscale Hard X-Ray Microscopy Methods for Materials Studies, Annu. Rev. Mater. Res. 43, 183 (2013).
  38. [39]P. G. Evans, D. E. Savage, J. R. Prance, C. B. Simmons, M. G. Lagally, S. N. Coppersmith, M. A. Eriksson, and T. U. Schülli, Nanoscale Distortions of Si Quantum Wells in Si/SiGe Quantum-Electronic Heterostructures, Adv. Mater. 24, 5217 (2012).DOI
  39. [40]J. Park, Y. Ahn, J. A. Tilka, K. C. Sampson, D. E. Savage, J. R. Prance, C. B. Simmons, M. G. Lagally, S. N. Coppersmith, M. A. Eriksson, M. V. Holt, and P. G. Evans, Electrode-stress-induced nanoscale disorder in Si quantum electronic devices, APL Mater. 4, 066102 (2016).DOI
  40. [41]M. H. Zoellner, M.-I. Richard, G. A. Chahine, P. Zaumseil, C. Reich, G. Capellini, F. Montalenti, A. Marzegalli, Y.-H. Xie, T. U. Schülli, M. Häberlen, P. Storck, and T. Schroeder, Imaging Structure and Composition Homogeneity of 300 mm SiGe Virtual Substrates for Advanced CMOS Applications by Scanning X-ray Diffraction Microscopy, ACS Appl. Mater. Interfaces 7, 9031 (2015).DOI
  41. [42]C. Corley-Wiciak, C. Richter, M. H. Zoellner, J. Zaitsev, C. L. Manganelli, E. Zatterin, T. U. Schülli, A. A. Corley-Wiciak, J. Katzer, F. Reichmann, W. M. Klesse, N. W. Hendrickx, A. Sammak, M. Veldhorst, G. Scappucci, M. Virgilio, and G. Capellini, Nanoscale Mapping of the 3D Strain Tensor in a Germanium Quantum Well Hosting a Functional Spin Qubit Device, ACS Appl. Mater. Interfaces 15, 3119 (2023).DOI
  42. [43]C. Corley-Wiciak, M. Zoellner, I. Zaitsev, K. Anand, E. Zatterin, Y. Yamamoto, A. Corley-Wiciak, F. Reichmann, W. Langheinrich, L. Schreiber, C. Manganelli, M. Virgilio, C. Richter, and G. Capellini, Lattice Deformation at Submicron Scale: X-Ray Nanobeam Measurements of Elastic Strain in Electron Shuttling Devices, Phys. Rev. Appl. 20, 024056 (2023).DOI
  43. [44]T. S. Perova, J. Wasyluk, K. Lyutovich, E. Kasper, M. Oehme, K. Rode, and A. Waldron, Composition and strain in thin Si₁₋ₓGeₓ virtual substrates measured by micro-Raman spectroscopy and x-ray diffraction, J. Appl. Phys. 109, 033502 (2011).DOI
  44. [45]F. Rovaris, M. H. Zoellner, P. Zaumseil, A. Marzegalli, L. Di Gaspare, M. De Seta, T. Schroeder, P. Storck, G. Schwalb, G. Capellini, and F. Montalenti, Dynamics of crosshatch patterns in heteroepitaxy, Phys. Rev. B 100, 085307 (2019).DOI
  45. [46]E. H. Chen, K. Raach, A. Pan, A. A. Kiselev, E. Acuna, J. Z. Blumoff, T. Brecht, M. D. Choi, W. Ha, D. R. Hulbert, M. P. Jura, T. E. Keating, R. Noah, B. Sun, B. J. Thomas, M. G. Borselli, C. Jackson, M. T. Rakher, and R. S. Ross, Detuning Axis Pulsed Spectroscopy of Valley-Orbital States in Si/SiGe Quantum Dots, Phys. Rev. Appl. 15, 044033 (2021).DOI
  46. [47]J. P. Dismukes, L. Ekstrom, E. F. Steigmeier, I. Kudman, and D. S. Beers, Thermal and electrical properties of heavily doped ge-si alloys up to 1300°k, Journal of Applied Physics 35, 2899 (1964).DOI
  47. [48]V. Sverdlov, Strain-Induced Effects in Advanced MOS-FETs, Computational Microelectronics (Springer Vienna, Vienna, 2011).
  48. [49]M. P. Losert, M. Oberländer, J. D. Teske, M. Volmer, L. R. Schreiber, H. Bluhm, S. Coppersmith, and M. Friesen, Strategies for Enhancing Spin-Shuttling Fidelities in Si/SiGe Quantum Wells with Random-Alloy Disorder, PRX Quantum 5, 040322 (2024).DOI
  49. [50]M. Friesen, M. A. Eriksson, and S. N. Coppersmith, Magnetic field dependence of valley splitting in realistic Si/SiGe quantum wells, Appl. Phys. Lett. 89, 202106 (2006).DOI
  50. [51]M. Friesen, S. Chutia, C. Tahan, and S. N. Coppersmith, Valley splitting theory of SiGe/Si/SiGe quantum wells, Phys. Rev. B 75, 115318 (2007).DOI
  51. [52]M. De Smet, Y. Matsumoto, A.-M. J. Zwerver, L. Tryputen, S. L. De Snoo, S. V. Amitonov, S. R. Katiraee-Far, A. Sammak, N. Samkharadze, Ö. Gül, R. N. M. Wasserman, E. Greplová, M. Rimbach-Russ, G. Scappucci, and L. M. K. Vandersypen, High-fidelity single-spin shuttling in silicon, Nat. Nanotechnol. 20, 866 (2025).DOI
  52. [53]A. Zwerver, S. Amitonov, S. de Snoo, M. Madzik, M. Rimbach-Russ, A. Sammak, G. Scappucci, and L. Vandersypen, Shuttling an Electron Spin through a Silicon Quantum Dot Array, PRX Quantum 4, 030303 (2023).DOI

Paper details

vlnc:W_8usa3tqe
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents