betaFeedback

WorksPhysics and Astronomy

Hydrophilic Porous Materials as Helmet Padding Able to Prevent Traumatic Brain Injuries

Abstract

The minimum possible value of the average deceleration of the head of a player engaged in an impact sport such as football or hockey, as a result of an impact of his/her helmet with a surface or another player, is inversely proportional to the helmet padding thickness. Since there are practical limits to its maximum thickness, it is difficult to significantly reduce the average acceleration. There is evidence, however, that the peak, rather than the average, acceleration is the most significant cause of brain injury. It is proposed here that brain injuries that occur as a result of an impact, could be reduced by using as padding a hydrophilic porous material swollen with fluid. The friction experienced by the fluid as it is squeezed out of the porous material in an impact can "tune" the acceleration of the skull so that it is never significantly higher than its average during the impact.

Introduction

In Ref. 1, Rowson and Duma conducted a study dedicated to determining the probability of the occurrence of concussions among football players during a game. They put forward a function of the peak deceleration amax⁡a_{\max} which gives the probability of the occurrence of a concussion for a given peak deceleration during an impact, based on a logical regression analysis of injury rates on the football field correlated with drop tests done on helmets. Their function is

R(amax⁡′)=11+e−(α+βamax⁡′)(1)R(a_{\max}') = \frac{1}{1+e^{-(\alpha+\beta a_{\max}')}} \tag*{(1)}

where amax⁡′=amax⁡/ga_{\max}' = a_{\max}/g, i.e., amax⁡′a_{\max}' is the deceleration amax⁡a_{\max} in units of the gravitational acceleration gg. Using statistics from NCAA college games, they obtain the following values for the parameters: α=−9.805\alpha=-9.805 and β=0.051\beta=0.051. Using statistics for NFL games these parameters have the values: α=−9.828\alpha=-9.828 and β=0.0497\beta=0.0497. Although the study reported in Ref. 1 only dealt with linear acceleration, it can be argued that the same forces on parts of the brain resulting from large linear acceleration of the brain, that are responsible for the occurrence of a concussion, will also occur for rotational acceleration that occurs in a rotational impact. This argument is based on the fact that the maximum value of the peak linear acceleration associated with a peak angular acceleration αmax⁡\alpha_{\max} is given by amax⁡=r0αmax⁡a_{\max}=r_0\alpha_{\max}, where r0r_0 is the distance between the center of mass of the brain and a point just below the inside surface of the skull[2]. This argument tells us that the way to reduce the probability of occurrence of a concussion in a rotational impact is to reduce the peak value of the angular acceleration. The ideal way to protect the brain from injury during an impact is to reduce the deceleration of the head as much as possible[3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16]. Assuming as a first approximation that during an impact of a helmeted head with a hard surface, the helmet stops moving instantaneously and the padding compresses by an amount Δz\Delta z as it reduces the speed of the head to zero, the average deceleration can be found from

V02+2aavΔz=V2=0,(2)V_{0}^{2}+2a_{av}\Delta z=V^{2}=0, \tag*{(2)}

where V0V_{0} and VV are the initial and final velocities, respectively, and aava_{av} is the average deceleration (average over Δz\Delta z). Then, it follows that

aav=−V022Δz(3)a_{av}=-\frac{V_{0}^{2}}{2\Delta z} \tag*{(3)}

For example, if the velocity just before the impact V0=5m/sV_{0}=5m/s (a typical running speed which corresponds to an impact energy of 37.5J37.5J, assuming the mass of the head to be 3kg3kg) and Δz=2.5×10−2m\Delta z=2.5\times10^{-2}m, aav=500m/s2a_{av}=500m/s^{2}. Then, it appears that ideally the padding should be made as soft as possible, while still stiff enough or thick enough so that it does not get completely compressed in an impact. There are practical limits on how thick one can make the padding (to prevent the padding from completely compressing before the velocity of the head is reduced to zero), however, no matter what material is used. What is proposed here is that since there are practical limitations on how small one can make the average deceleration because of limitations on the padding thickness, an alternative approach is to design the padding so that the peak deceleration is never significantly larger than its average value.

The padding used in football helmets today is either a polyurethane or vinyl nitrate foam, which has the disadvantage that it results in a very large peak deceleration[17]. As was stated earlier, for a given pad thickness, the lowest average deceleration that can be achieved is V02/(2ℓ)V_{0}^{2}/(2\ell), where ℓ\ell is the thickness of the padding. For foam used in typical football helmets for an impact energy of 30J30J, which corresponds to an initial velocity of 4.47m/s4.47m/s, the maximum acceleration for the foam padding in Ref. 17 was 408g. This gives a value for RR, given in Eq. (1), almost equal to one, implying a high probability of a brain injury. Even the VICIS helmet, which is considered the state of the art in injury preventing football helmets, has a highly peaked deceleration profile. Figure 1 shows the deceleration versus time for the VICIS helmet found in finite element simulations performed by the NFL to reproduce results of impact tests done on several helmets presently in use[18]. Similar time dependence for the deceleration was found for the other helmets that they tested. The value of RR for the data shown in Figure 1 is 0.0231, using the parameters given above for NFL games. The authors of Ref. 17 proposed using shear thickening fluids (STF) as helmet padding. These are colloid materials whose viscosity increases rapidly as the rate at which stress is applied to them increases. For a 3.3cm3.3cm thick pad of the STF studied in Ref. 17, the maximum acceleration for a 30J30J impact was 119g119g, which gives R=0.02R=0.02. We will see that padding made from a 4cm thick hydrophilic porous material swollen with water can give a peak deceleration of 667m/s2=68.1g667m/s^{2}=68.1g with the optimum choice of parameters, for an initial velocity of 5m/s5m/s, which gives R=0.00159R=0.00159. One reason that porous materials swollen with water can potentially do a better job in preventing brain injuries is that such materials provide significant deceleration at the beginning of the impact (i.e., well before the padding is significantly compressed). This makes it easier to produce a deceleration during the impact close to being constant. Ref. 19 suggests that nearly constant acceleration could be produced by expulsion of water from a water shock absorber (i.e., a container with a hole in it that allows water to escape as the container is compressed during an impact to it). Porous materials swollen with water can produce close to the constant acceleration that such a shock absorber can produce, but as will be discussed in section III, the porous material may be better suited to be used as helmet padding[20] because it might be easier to put it in a helmet.

Acceleration of a model head in a VICIS helmet as a function of time

Figure 1. The acceleration of a model head in a VICIS helmet as a function of time from the NFL’s simulation based on their testing of this helmet, for an initial velocity of the helmet of 3.61m/s3.61m/s and a final velocity of −3.61m/s-3.61m/s.

Theory of Porous Material Helmet Padding

Consider a porous padding material, which is initially swollen with water, when it is impacted with a slightly curved object of mass mm and a velocity V0V_0. This is a model for a head inside a helmet making an impact with a pad whose dimensions are small compared of those of the head, eliminating the need to account for the head’s curvature, to a good approximation. Let us enclose the porous material in a circular cylinder with holes in its side, to allow fluid to escape as the material is compressed, but with a solid bottom and piston, so that the fluid flows only out the sides, as illustrated in Figure 2. The cylinder must be enclosed in a watertight soft elastic wrapper to catch fluid that is expelled during compression, keeping it in contact with the sides of the cylinder and thus allowing it to be reabsorbed after the impact.

Porous material contained within a cylinder used as helmet padding

Figure 2. This figure illustrates how a porous material can be used to function as helmet padding. The porous material is contained within the cylinder. There would be several of these pads distributed around the inside of the helmet.

A major source of head injury is believed to be due to rotational acceleration of the head. In the case of head rotation, it is the maximum angular acceleration that must be reduced to prevent concussions, as described above. The maximum angular acceleration can be reduced by including in the helmet impact absorbing cylinders described above, but attached to the sides of an insert in the helmet (in contact with the head), in order to reduce the maximum angular acceleration of the head in a rotational impact, as illustrated in Figure 3.

A schematic of an insert placed in the helmet to mitigate effects of rotational impacts

Figure 3. A schematic of an insert placed in the helmet to mitigate effects of rotational impacts. The insert shell would actually be in contact with the head.

Let the initial and instantaneous thickness of the porous material be ℓ\ell and zz, respectively, and hence, Δz\Delta z in Eqs. (2) and (3) is equal to ℓ−z\ell-z. The force that the surface of the porous material must exert on the head to decelerate it is given by Newton’s second law,

F=md2zdt2,(4)F=m\frac{d^{2}z}{dt^{2}}, \tag*{(4)}

where mm is the mass of the head. Then setting the rate of decrease of the volume of the material equal to the volume rate of flow of fluid through the sides, we get

πR2dzdt=2πRzv,(5)\pi R^{2}\frac{dz}{dt}=2\pi Rzv, \tag*{(5)}

where vv is the mean velocity of fluid flow out the sides of the cylinder, and as discussed above, we have assumed that the pad is enclosed in a circular cylinder of radius RR. Here, it will be assumed that FF is dominated by the friction that the water exerts on the porous material when it is expelled from it. This assumption will be justified later by numerically solving a model that includes both this friction mechanism and the elasticity of the solid material in the padding. Therefore, we may assume that the flow velocity of the water vv is determined by the permeability of the porous material, and hence, is given by

v∼k(F/πR2)(1/R)(6)v \sim k(F/\pi R^2)(1/R) \tag*{(6)}

where kk is the permeability of the material, F/πR2F/\pi R^2 is the fluid pressure applied to the porous material and the mean distance that the expelled fluid flows is of the order of RR. (The permeability is often expressed as a quantity with units of distance squared, given by η/k\eta/k in terms of the permeability kk defined by Eq. (6), where η\eta is the dynamic viscosity of water.)

For the geometry shown in Figure 2, the permeability should be proportional to the sample thickness, and hence, k=k0(z/ℓ)k=k_0(z/\ell). To justify this assumption, think of the water flowing through a bunch of pipes running from inside the porous material to the outside. Then since only the vertical dimension of each pipe gets reduced by a factor z/ℓz/\ell, the total cross-sectional area of each pipe gets reduced by this factor. Combining Eqs. (4)-(6), we obtain the differential equation:

d2zdt2=−ℓπR42k0z2mdzdt=−a0ℓ2V0z2dzdt,(7)\frac{d^2z}{dt^2}=-\frac{\ell\pi R^4}{2k_0z^2m}\frac{dz}{dt}=-\frac{a_0\ell^2}{V_0z^2}\frac{dz}{dt}, \tag*{(7)}

where a0a_0 is the initial acceleration. The elasticity of the solid part of the porous material can be included by adding a term −(GπR2/m)(1−z/ℓ)-(G\pi R^2/m)(1-z/\ell) to the right hand side of Eq. (7), where GG is the compressional elastic constant of the solid part of the porous material. For now, we will neglect this term. As mentioned above, however, it will be demonstrated below that the results obtained without including this term are not modified significantly if it is included. There exist hydrogels with cavities which can have a different dependence of kk on z/ℓz/\ell [21]. Results of calculations done on this model with k=k0(z/ℓ)αk=k_0(z/\ell)^\alpha for a few values of α\alpha are given in the appendix. Integrating Eq. (7) once, assuming that the initial value of dz/dt=−V0dz/dt=-V_0, we obtain

dzdt=−V0+(a0ℓ/V0)(ℓz−1),(8)\frac{dz}{dt}=-V_0+(a_0\ell/V_0)\left(\frac{\ell}{z}-1\right), \tag*{(8)}

whose solution is

ln⁡∣Aℓ(1+A)z−Aℓ∣=V0(1+A)2tℓA+(ℓ−z)1+AℓA,(9)\ln\left|\frac{A\ell}{(1+A)z-A\ell}\right|=\frac{V_0(1+A)^2t}{\ell A}+(\ell-z)\frac{1+A}{\ell A}, \tag*{(9)}

where A=a0ℓ/V02A=a_0\ell/V_0^2. As tt becomes large compared to

ℓV0A(1+A)2(10)\frac{\ell}{V_0}\frac{A}{(1+A)^2} \tag*{(10)}

the right hand side of Eq. (9) becomes large, and therefore, the value of zz decays from ℓ\ell to its final value zmin⁡z_{\min}, given by

zmin⁡ℓ=A1+A(11)\frac{z_{\min}}{\ell}=\frac{A}{1+A} \tag*{(11)}

(since the logarithm becomes infinite at this value). Substituting Eq. (8) into Eq. (7), we obtain

a=d2zdt2=a01u2[1−A(u−1−1)],(12)a=\frac{d^2z}{dt^2}=a_0\frac{1}{u^2}\left[1-A\left(u^{-1}-1\right)\right], \tag*{(12)}

where u=z/ℓu=z/\ell. The value of zz at which aa is maximum (za,max⁡z_{a,\max}) is obtained from

1ℓ2a0dadz=−2z3[1−A(u−1−1)]+Auz3=0,(13)\frac{1}{\ell^2a_0}\frac{da}{dz}=-\frac{2}{z^3}\left[1-A\left(u^{-1}-1\right)\right]+\frac{A}{uz^3}=0, \tag*{(13)}

whose solution is

za,max⁡ℓ=32A1+A=32zmin⁡ℓ.(14)\frac{z_{a,\max}}{\ell}=\frac{3}{2}\frac{A}{1+A}=\frac{3}{2}\frac{z_{\min}}{\ell}. \tag*{(14)}

Substituting za,max⁡z_{a,\max} for zz in Eq. (12), we obtain for the maximum acceleration

amax⁡a0=427(1+A)3A2.(15)\frac{a_{\max}}{a_0}=\frac{4}{27}\frac{(1+A)^3}{A^2}. \tag*{(15)}

Since

za,max⁡=(3/2)zmin⁡<ℓ,(16)z_{a,\max}=(3/2)z_{\min}<\ell, \tag*{(16)}

(because ℓ\ell is the maximum value of zz), we find from Eq. (14) that we must have

A≤2.(17)A\leq2. \tag*{(17)}

If this condition is not satisfied, amax⁡=a0a_{\max}=a_0, which occurs right at the beginning of the impact, when z=ℓz=\ell. The average (over zz) of the acceleration is given by

aav=V022(ℓ−zmin⁡)=a0(1+A2A),(18)a_{\mathrm{av}}=\frac{V_0^2}{2(\ell-z_{\min})}=a_0\left(\frac{1+A}{2A}\right), \tag*{(18)}

from Eq. (3) (noting that Δz\Delta z in Eq. (3) is equal to ℓ−zmin⁡\ell-z_{\min}) and Eq. (10b), and hence, from Eqs. (15) and (18)

amax⁡aav=827(1+A)2A,(19)\frac{a_{\max}}{a_{\mathrm{av}}}=\frac{8}{27}\frac{(1+A)^2}{A}, \tag*{(19)}

for A≤2A \le2. If we minimize (19) with respect to AA, we find that the minimum value of amax⁡/aav=1.19a_{\max}/a_{\mathrm{av}}=1.19, which occurs for A=1A=1.

Let us now look at how all of the above parameters depend on ℓ\ell. Since

A=a0ℓV02=πR42k0mV0,(20)A=\frac{a_0\ell}{V_0^2}=\frac{\pi R^4}{2k_0mV_0}, \tag*{(20)}

we see that AA is independent of ℓ\ell, and hence, zmin⁡/ℓz_{\min}/\ell and za,max⁡/ℓz_{a,\max}/\ell are independent of ℓ\ell. From the definition of AA, given above Eq. (10a), along with Eqs. (14) and (17), we find that the quantities a0a_0, amax⁡a_{\max} and aava_{\mathrm{av}} are inversely proportional to ℓ\ell. The table below illustrates how the ratio amax⁡/aava_{\max}/a_{\mathrm{av}} depends on AA

AAamax⁡/aava_{\max}/a_{\mathrm{av}}
0∞\infty
0.51.33
1.01.19
1.51.23
2.01.33
3.01.5
4.01.6
∞\infty2.0

Table 1. The ratio amax⁡/aava_{\max}/a_{\mathrm{av}} is given for several values of AA.

In this table, amax⁡/aav=a0/aava_{\max}/a_{\mathrm{av}}=a_0/a_{\mathrm{av}} for A>2A>2. It illustrates that for 0.5<A<20.5<A<2, amax⁡/aav≤1.33a_{\max}/a_{\mathrm{av}}\le1.33. Since from (20), V0=(πR4/2k0mA)V_0=(\pi R^4/2k_0mA), we conclude that such low values of amax⁡/aava_{\max}/a_{\mathrm{av}} can be obtained for an impact velocity range of 0.5(πR4/2k0m)<V0<2(πR4/2k0m)0.5(\pi R^4/2k_0m)<V_0<2(\pi R^4/2k_0m), which would mean for example that if we chose the parameters so that (πR4/2k0m)=5m/s(\pi R^4/2k_0m)=5m/s, we would have amax⁡/aav≤1.33a_{\max}/a_{\mathrm{av}}\le1.33 for 2.5m/s<V0<10m/s2.5m/s<V_0<10m/s. The relative amount of compressions for a given value of AA is given by (ℓ−z)/ℓ=(1+A)−1(\ell-z)/\ell=(1+A)^{-1}, which for the above range of values of AA, varies between 0.333 and 0.667. The values of amax⁡/aava_{\max}/a_{\mathrm{av}} given in the appendix for other dependencies of the permeability on the compression of padding are comparable to these values. This implies that there are probably several different porous materials that can be used to reduce amax⁡/aava_{\max}/a_{\mathrm{av}}.

The above expressions for amax⁡a_{\max} and aava_{av} can also be written as

amax⁡=427(1+A)3AV02ℓ(21)a_{\max}=\frac{4}{27}\frac{(1+A)^3}{A}\frac{V_0^2}{\ell} \tag*{(21)}

and

aav=(1+A)V022ℓ.(22)a_{av}=(1+A)\frac{V_0^2}{2\ell}. \tag*{(22)}

It is easily shown that amax⁡a_{\max} is minimum for A=0.5A=0.5, and for this value amax⁡=V02/ℓa_{\max}=V_0^2/\ell, aav=0.75V02/ℓa_{av}=0.75V_0^2/\ell and ℓ−zmin⁡=0.667ℓ\ell-z_{\min}=0.667\ell. Then, for example, if V0=5m/sV_0=5m/s and ℓ=3.75×10−2m\ell=3.75\times10^{-2}m, aav=500m/s2a_{av}=500m/s^2 and amax⁡=667m/s2a_{\max}=667m/s^2.

The quantity (πR4/2k0m)=5m/s(\pi R^4/2k_0m)=5m/s for R=3.65cmR=3.65cm for example, m=3kgm=3kg and k0=1.86×10−7m4/Nsk_0=1.86\times10^{-7}m^4/Ns. Since k0=ζ2/ηk_0=\zeta^2/\eta, where ζ\zeta is the root mean square pore size, ζ=(k0η)1/2=1.35×10−5m\zeta=(k_0\eta)^{1/2}=1.35\times10^{-5}m, where η\eta is the viscosity of water.

In order to justify the neglect of the elasticity of the solid material in the above discussion, let us include the elastic term discussed under Eq. (7), to account for the elasticity of the solid material of the sample and solve the resulting differential equation,

d2zdt2=−a0ℓ2V0z2dzdt−GπR2m(1−zℓ),(23)\frac{d^2z}{dt^2}=-\frac{a_0\ell^2}{V_0z^2}\frac{dz}{dt}-\frac{G\pi R^2}{m}\left(1-\frac{z}{\ell}\right), \tag*{(23)}

numerically. When the weight is placed at rest on the padding the material,

GπR2(1−zℓ)=mg.(24)G\pi R^2\left(1-\frac{z}{\ell}\right)=mg. \tag*{(24)}

The results are shown in Figure 4a for the value of GG which gives 1−z/ℓ=0.6261-z/\ell=0.626 when the weight rests on the padding, determined from Eq. (24). In Figure 4b the value of GG is 20 times larger than its value in Figure 4a, and in Figure 4c, G=0G=0 for comparison. From these figures, it can be seen that including the elasticity term does not significantly change the acceleration versus compression curves, which indicates that the above calculations based on a model that assumes that the water friction dominates over the elasticity is a good approximation.

Figure 4. The acceleration of the weight is plotted as a function of the compression of the padding during the impact with A=1.5A=1.5 and for a. G=1.12×104 PaG=1.12 \times10^{4}\,Pa chosen so that when a 3kg3kg weight rests on the pad (1−z/ℓ)(1-z/\ell) given by Eq. (24) is equal to 0.626, b. GG is 20 times the value in a, and c. for G=0G=0.

Let us consider a numerical example of how effective the porous material is in preventing brain injuries. For the maximum acceleration of 667m/s2667m/s^{2} or 68.1g68.1g found in the example worked out under Eq. (21), we obtain from Eq. (1) that the probability of a concussion, R=0.00178R=0.00178 for the NCAA parameters and for the NFL parameters, it is R=0.00159R=0.00159, showing that the probability of a brain injury is extremely low.

A possible Way to Produce a Porous Material Helmet Pad which is Able to Prevent Brain Injuries

In order to achieve a maximum acceleration comparable to the relatively small values given above, we saw that the pore size required for our porous material must be of the order of between 10−6−10−5 m10^{-6}-10^{-5}\,m. Recently, there has been an interest in developing highly porous materials using optical etching of ceramic materials [22, 23, 24] or 3d printing.[25, 26, 27, 28] The porous materials reported in Refs. [22, 23, 24] by Greer’s group have compressional moduli of the order of 104−106 Pa10^{4}-10^{6}\,Pa and those produced by Yakacki’s group from liquid crystal elastomers[25, 26, 27, 28] give moduli of the order of 104−105 Pa10^{4}-10^{5}\,Pa. The value of GG which gives z/ℓ=0.5z/\ell=0.5, for example, when the weight comes to rest after the impact, is in the range of compressional moduli that occur for the porous liquid crystal elastomers discussed above [25, 26, 27, 28].

Comparisons with other Approaches

Studies of the head deceleration produced by a multilayer pad with a stiffer pad sandwiched between more compressible layers (padding used by the military) show that this type of padding produces a maximum deceleration rate of about 120g, which according to Eq. (1) gives a 10% probability of a concussion[29]. Padding consisting of a porous material swollen with water, as well as the shear thickening liquid padding, discussed in Ref. 17, as well as several other proposed methods that will be discussed in this section give a much lower probability of a concussion. Recently, it has been demonstrated that a shock absorber consisting of a collapsible container containing water can result in a low peak acceleration in an impact.[19] This approach has the advantage that the shock absorber can be engineered to produce a precisely constant deceleration rate during an impact to it. It has the disadvantages, however, that it is difficult to design such a device that will fit into a helmet and it is not obvious that it is possible to design such a device that will re-absorb the water expelled in an impact before the next impact takes place. Also, as was noted in the introduction, it has been demonstrated that padding that contains a shear thickening liquid is also able to reduce the peak acceleration in an impact[17], although from the discussion in the previous sections, the mechanism proposed here can potentially be more effective at preventing concussions. More recently Mistry, et. al. [27] have shown that “soft elasticity” in liquid single domain crystal elastomers can give rise to a stress versus-strain curve which flattens out as the strain increases as a result of rotation of the liquid crystal directors during an impact. Such materials were shown to give rise to a stress versus strain curve which is a little closer to the ideal constant stress versus strain behavior[19], but the stress-strain curve that they found in their impact tests is still farther away from the behavior that is possible for the mechanism suggested in this paper. Spinelli, et. al.[30], have demonstrated that a helmet held on the head with stretchable straps containing a shear thickening liquid can produce a reasonably constant acceleration of the head in an impact, at least for impact speeds below 4.5m/s4.5m/s. At 4.5m/s4.5m/s, however, the ratio amax⁡/aava_{\max}/a_{\mathrm{av}} appears to be closer to 2.

Conclusions

It was argued that helmet padding made from hydrophilic porous materials swollen with water with pore size of between 1 and 10 microns can be effective in preventing concussions in high impact sports by reducing the value of the maximum deceleration and angular deceleration rate of the head relative to the helmet during an impact to the helmet. Although there is evidence that even repeated sub-concussive impacts cause long term damage to the brain[31, 32, 33, 34, 35, 36, 37], reducing the peak acceleration, which reduces the maximum forces acting on various parts of the brain will, in addition to reducing the likelihood of a concussion, likely also reduce the damage caused by sub-concussive impacts.

Appendix

Results of several calculations of the acceleration versus the amount of compression 1−z/ℓ1-z/\ell of a porous material swollen with water for a permeability of the form k=k0(z/ℓ)αk=k_0(z/\ell)^\alpha with a few values of α\alpha will be given here. Eq. (7) is replaced by

d2zdt2=−a0V0(ℓz)α+1dzdt(25)\frac{d^2z}{dt^2}=-\frac{a_0}{V_0}\left(\frac{\ell}{z}\right)^{\alpha+1}\frac{dz}{dt} \tag*{(25)}

whose solution for the velocity is

dzdt=V0[−1+A(u−α−1)](26)\frac{dz}{dt}=V_0\left[-1+A(u^{-\alpha}-1)\right] \tag*{(26)}

where u=z/ℓu=z/\ell. Substituting Eq. (26) into Eq. (25), we get

a=d2zdt2=a0[(1+Aα)1uα+1−An1u2α+1](27)a=\frac{d^2z}{dt^2}=a_0\left[\left(1+\frac{A}{\alpha}\right)\frac{1}{u^{\alpha+1}}-\frac{A}{n}\frac{1}{u^{2\alpha+1}}\right] \tag*{(27)}

The average acceleration is given by

aav=V022(ℓ−umin⁡)=a0A11−umin⁡,(28)a_{\mathrm{av}}=\frac{V_0^2}{2(\ell-u_{\min})}=\frac{a_0}{A}\frac{1}{1-u_{\min}}, \tag*{(28)}

where umin⁡u_{\min} is the value of uu at which dz/dt=0dz/dt=0. Based on Eq. (27), aa is plotted as a function of uu for α=1.5\alpha=1.5 for some values of AA below:

Plot of a/a0 versus 1-u for alpha = 1.5 and A = 1

Figure 5. This is a plot of a/a0a/a_0 versus 1−u1-u for α=1.5\alpha=1.5 and for A=1A=1.

From Eq. (28), aav/a0=1.00a_{\mathrm{av}}/a_0=1.00, so that amax⁡/aav=1.3a_{\max}/a_{\mathrm{av}}=1.3.

Plot of $a$ versus $1-u$ for $\alpha=1.5$ and $A=1.5$

Figure 6. A plot of aa versus 1−u1-u for α=1.5\alpha=1.5 and for A=1.5A=1.5.

From Eq. (28), aav/a0=0.952a_{\mathrm{av}}/a_0=0.952, so that amax⁡/aav=1.16a_{\max}/a_{\mathrm{av}}=1.16.

Plot of $a$ versus $1-u$ for $\alpha=1.5$ and $A=2$

Figure 7. A plot of aa versus 1−u1-u for α=1.5\alpha=1.5 and A=2A=2.

From Eq. (28), aav/a0=0.833a_{\mathrm{av}}/a_0=0.833, so that amax⁡/aav=1.20a_{\max}/a_{\mathrm{av}}=1.20.

Plots are given below of aa versus 1−u1-u for α=3\alpha=3 for several values of AA:

Plot of $a$ versus $1-u$ for $\alpha=3$

Figure 8.

Plot of $a$ versus $1-u$ for $\alpha=3$ for $A=1\_5$

Figure 8 (PDF p. 13). A plot of aa versus 1−u1-u for α=3\alpha=3 for A=1_5A=1\_5. From Eq. (28), aav/a0=1.11a_{\mathrm{av}}/a_0=1.11, so that amax⁡/aav=1.17a_{\max}/a_{\mathrm{av}}=1.17.

Plot of $a$ versus $1-u$ for $\alpha=3$ and $A=2$

Figure 9. A plot of aa versus 1−u1-u for α=3\alpha=3 and A=2A=2. From Eq. (28), aav/a0=1.00a_{\mathrm{av}}/a_0=1.00, so that amax⁡/aav=1.1a_{\max}/a_{\mathrm{av}}=1.1.

Image not extracted

Figure 10. A plot of aa versus 1−u1-u for α=3\alpha=3 and A=3A=3. From Eq. (28), aav/a0=0.809a_{\mathrm{av}}/a_0=0.809, so that amax⁡/aav=1.24a_{\max}/a_{\mathrm{av}}=1.24.

Acknowledgements

I wish to thank Robert Weiss and Brian Vogt of the University of Akron and Adam Ekenseair of Northeastern University for discussions that we had related to this project. Regarding the material quoted in Ref. 18: The author(s) acknowledge Biomechanics Consulting and Research, LC and Football Research, Inc. for supporting the development and licensing the use of models used in this study. The study’s conclusions do not represent the conclusions or opinions of either such entity.

References

References

  1. [2]E. S. Guridjian, V. L. Roberts and L. M. Thomas, L. M., Journal of Trauma 6(5), 600 (1966).
  2. [3]P. V. Bayly, T. S. Cohen, E. P. Leister, D. Ajo, E. Leuthardt and G. M. Genin, Journal Neurotrauma 22(8), 845-856 (2005).
  3. [4]See video at www.youtube.com/watch?v=m8W5X0s2AhU.
  4. [5]B. R. Donnelly and J. Medige, Journal of Biomechanical Engineering 119, 423-432 (1997).
  5. [6]P. V. Bayly, T. S. Cohen, E. P. Leister, D. Ajo, E. Leuthart and G. M. Genin, Journal of Neurotrauma 22(8), 845-856 (2005).
  6. [7]Y. Feng, T. M. Abney, R. J. Okamoto, R. B. Pless, G. M. Genin and P. V. Bayly, Journal of the Royal Society Interface 7(53), 1677-1688 (2010).
  7. [8]N. Yoganandan, J. Li , J. Zhang, F. A. Pintar and T. Gennarelli, Journal of Biomechanics 41(10), 2253-2262 (2008).
  8. [9]S. S. Margulies, L. E. Thibault and T. Gennarelli, Journal of Biomechanics 23(8), 823-836 (1990).
  9. [10]L. Zhang, K. H. Yang, and A. I. King, Journal of Neurotrauma 18, 21-30 (2001).
  10. [11]D. R. S. Bradshaw, J. Ivarsson, C. L. Morfey and D. C. Viano, Journal of Biomechanics 34(1), 85-94 (2001).
  11. [12]J. Ivarsson, D. C. Viano, P. Lovsund and B. Aldman, Journal of Biomechanics 33(2), 181-189 (2000).
  12. [13]P. Bittigau, M. Sifringer, D. Pohl, D. Stadthaus, M. Ishimaru, H. Shimzu, M. Ikeda, D. Lang, A. Speer, J.M. Olney and C. Ikonomidou, Annals of Neurology 45(6), 724-735 (1999).
  13. [14]K. T. Dikranian, R. Cohen, C. Mac Donald, Y. Pan, D. Brakefield, P. V. Bayly and A. Parsadanian, Experimental Neurology 211(2), 551-560 (2008).
  14. [15]M.-C.-Lee and R. C. Haut, Journal of Biomechanics 22(6/7), 537-542 (1989).
  15. [16]K. Laksari, L. Wu, M. Kurt and D. Camarillo, Journal of the Research Society Interface 12(108), 20150331 (2015).
  16. [17]J. Fowler, A. A. Pallanta, G. B. Swanik and J. N. Wagner, Journal of Biomechanical Engineering 137(5), 054504 (2015).
  17. [18]J. S. Giudice, A. Caudillo, S. Mukherjee, K. Kong, G. Park, R. Kent, M. B. Panzer, Ann Biomed Eng. 48(5), 1524-1539 (2020), doi: 10.1007/s10439-020-02472-6. Epub 2020 Feb 7. PMID: 32034610.
  18. [19]M. Fanton, H. V. Alizadeh, A. G. Domel, M. Devlin, M. Kurt, M. G. Mungal, D. B. Camarillo and E. Hawkes, Smart Materials and Structures 29(8), 085023 (2020); H. V. Alizadeh, M. G. Fanton, A. G. Domel, G. Grant, D. B. Camarillo, ArXiv 1910.07722.arxiv.org/abs/1910.07722
  19. [20]J. B. Sokoloff, 2019, United States Patent Office, patent application no. 16237927 (2019).
  20. [21]R. J. Hill, J. Fluid Mech. 936, A27 (2022).
  21. [22]C. M. Portela, A. Vidyasagar, S Krodel, T. Weissenbach, D. W. Yee, J.R. Greer and D. M. Kochmann, Proceedings of the National Academy of Science (USA) 117(11), 5686 (2020).
  22. [23]W. P. Moestopo, A. J. Mateos, R. M. Fuller, J. R. Greer and C. M. Portela, Adv. Sci. 7(20), 2001271 (2020).
  23. [24]X. Zhang, L. Zhong, A. Mateos, A. Kudo, A. Vyatskikh, H. Gao, J. R. Greer and X. Li, Nature Nanotechnology 14(8), 762 (2019).
  24. [25]C. Luo, C. Chung, N. A. Traugutt, C. M. Yakacki, K. N. Long and K. Yu, ACS Applied Materials and Interfaces 13(11), 12698 (2021).
  25. [26]S. W. Ula, N. A. Traugutt, R. H. Volpe, R. P. Patel, K. Yu and C. M.Yakacki, Liquid Crystals Reviews 6(1), 78 (2018).
  26. [27]N. R. Traugutt, D. Mistry, C. Luo, K. Yu, Q. Ge and C. M. Yakacki, Adv. Mater. 32(28), 2000797 (2020).
  27. [28]D. Mistry, N. A. Traugutt, B. Sanborn, R. H. Volpe, L. S. Chatham, R. Zhou, B. Song, K. Yu, K. Long, C. M. Yakacki, Arxiv 2106.02165.DOI
  28. [29]W.C. Moss, M.J. King & E.G. Blackman, Computer Methods in Biomechanics and Biomedical Engineering, 17, 1173 (2014).
  29. [30]D. J. Spinelli, T. A. Plaisted E. D. and Wetzel, Materials and Design 154, 153–169 (2018).
  30. [31]Bailey Hiles-Murison, Andrew P. Lavender, Mark J. Hackett, Joshua J.Armstrong, Michael Nesbit, Samuel Rawlings, Terrence McGonigle, AndrewWarnock1, Virginie Lam1, John C. L. Mamo1, Melinda Fitzgerald and RyuTakechi1, Scientific Reports 11, 9261 (2021).
  31. [32]R. Davis Moore, Julien Lepine, Dave Ellemberg, International Journal of Psychophysiology 112, 22 (2017).
  32. [33]Vikram Puvvenna, Chad Brennan, Gerald Shaw, Cui Yang6 , Nicola Marchi, Jeffrey J. Bazarian, Kian Merchant-Borna, Damir Janigro, PLOS 9, 96296 (2014).
  33. [34]Allen A Champagne, Nicole S Coverdale, Mike Germuska, Alex A Bhogal and Douglas J Cook, Journal of Cerebral Blood Flow and Metabolism 40, 1453 (2019).
  34. [35]Michail Ntikas, Ferdinand Binkofski, N. Jon Shah and Magdalena Ietswaart, Int. J. Environ. Res. Public Health 19, 7098 (2022).
  35. [36]Kian Merchant-Borna , Patrick Asselin, Darran Narayan, Beau Abar, Courtney M. C. Jones and Jeffrey J. Bazarian, Annals of Biomedical Engineering, 44, 3679 (2016).
  36. [37]J.K. Dierijcka , A.D. Wrighta, J.D. Smirla , K. Bryk, P. van Donkelaar, International Journal of Psychophysiology 132, 74 (2018).

Paper details

vlnc:W_9472s4pr
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents