betaFeedback

WorksPhysics and Astronomy

Investigation of Cryogenic Current-Voltage Anomalies in SiGe HBTs: Role of Base-Emitter Junction Inhomogeneities

Abstract

The deviations of cryogenic collector current-voltage characteristics of SiGe heterojunction bipolar transistors (HBTs) from ideal drift-diffusion theory have been a topic of investigation for many years. Recent work indicates that direct tunneling across the base contributes to the non-ideal current in highly-scaled devices. However, cryogenic discrepancies have been observed even in older-generation devices for which direct tunneling is negligible, suggesting another mechanism may also contribute. Although similar non-ideal current-voltage characteristics have been observed in Schottky junctions and were attributed to spatial inhomogeneities in the base-emitter junction potential, this explanation has not been considered for SiGe HBTs. Here, we experimentally investigate this hypothesis by characterizing the collector current ideality factor and built-in potential of a SiGe HBT versus temperature using a cryogenic probe station. The temperature-dependence of the ideality factor and the relation between the built-in potential as measured by capacitance-voltage and current-voltage characteristics are in good qualitative agreement with the predictions of a theory of electrical transport across a junction with a Gaussian distribution of potential barrier heights. These observations suggest that lateral inhomogeneities in the base-emitter junction potential may contribute to the cryogenic non-idealities. This work helps to identify the physical mechanisms limiting the cryogenic microwave noise performance of SiGe HBTs.

Introduction

Silicon-germanium heterojunction bipolar transistors (HBTs) are widely used in microwave applications such as high-speed communications and radar systems owing to their competitive microwave performance, low cost, and ease of integration compared with III-V compound semiconductor devices [1]. Technological advances such as reduced emitter widths, decreased base resistances and extrinsic capacitances, and advanced epitaxial techniques have enabled microwave noise performance approaching that of III-V high electron mobility transistors [2, 3]. As a result, cryogenic SiGe HBTs have recently been considered for applications in quantum computing and radio astronomy [4, 5, 6].

The cryogenic microwave performance of SiGe HBTs has been investigated following their initial development in the 1980s [7] as various performance metrics such as transconductance and noise figure improve with cooling. However, below ∼77\sim77 K, these improvements are observed to plateau with decreasing temperature [8, 9, 10], corresponding to a temperature-dependent collector current ideality factor n(T)n(T) that greatly exceeds unity at cryogenic temperatures [11, 12]. This behavior differs markedly from the predictions of drift-diffusion theory for fabricated p-n junctions for which nn is close to unity and independent of temperature, and the transconductance increases inversely with temperature. [13, 14] Because the minimum noise temperature is directly proportional to n(T)n(T) in the low-frequency and low base-resistance limit (see [4 Eq. 2]), identifying the physical origin of the discrepancies is necessary to improve the cryogenic microwave noise performance of SiGe HBTs.

The cryogenic non-ideal behavior has been attributed to various mechanisms including quasiballistic transport [9, 10], direct tunneling [11], or trap-assisted tunneling [15]. However, a theoretical study has reported that quasiballistic electron transport cannot explain the observed collector cryogenic non-idealities [16]. Recent works indicate that direct tunneling across the base can account for the non-idealities in highly-scaled devices [5, 11, 12, 17]. At the same time, non-idealities have been observed in devices with base widths of ∼100\sim100 nm [5, 9] for which direct tunneling is negligible. This observation suggests that, in addition to tunneling, another mechanism may contribute to cryogenic non-ideal current-voltage characteristics in SiGe HBTs.

In a different context, similar anomalies have been observed and extensively investigated in Schottky diodes [18, 19, 20, 21], and they were ultimately attributed to spatial inhomogeneities in the built-in potential ΦBI\Phi_{BI}. [22, 23, 24, 25] Although semiconductor junctions are often modeled as uniform across the lateral area, in fact various imperfections exist which affect the local electronic structure of the junction, a point which was recognized as early as 1950. [26] Even at epitaxial interfaces, it was found that different crystallographic orientations [27, 28, 29] or the presence of dislocations [30, 31] can lead to potential barrier height variations on the order of hundreds of mV. In Schottky junctions, these inhomogeneities have been directly observed using ballistic electron emission microscopy. [32, 33] Various theories and numerical analyses of the electrical characteristics of inhomogeneous junctions have been reported and lead to compatible conclusions. [22, 23, 24] For concreteness, the theory of Werner and Güttler assumes a Gaussian distribution of barrier heights and makes several predictions regarding the temperature-dependence of the ideality factor and the relation between the built-in potential as measured by different methods. [23, 34, 35] However, an experimental test of these predictions for SiGe HBTs has not yet been reported.

Here, we perform this experimental investigation by characterizing the collector current ideality factor and built-in potential of a SiGe HBT from room to cryogenic temperatures. We find that the measured temperature-dependence of the ideality factor and the relation between built-in potential as determined by capacitance-voltage and current-voltage characteristics are compatible with the theory predictions. This observation suggests that inhomogeneities in the base-emitter junction potential could be a mechanism affecting the cryogenic current-voltage characteristics in SiGe HBTs. We discuss how the existence of barrier inhomogeneities could be further confirmed. Our work advances efforts to improve the cryogenic electrical characteristics and hence microwave noise performance of SiGe HBTs.

Theory and Methods

Overview

The theory of Werner and Güttler describes electrical transport across a potential barrier with heights distributed according to a Gaussian distribution of a specified mean and variance. [23] The variance of the distribution is assumed to decrease with increasing junction bias due to the pinch-off of low-barrier patches of dimension less than the depletion length, a concept that was originally introduced in [24] and later developed in [22]. The theory makes several predictions regarding the trends of electrical characteristics with temperature and other parameters in junctions exhibiting voltage-independent ideality factors n(T)n(T). In particular, n(T)n(T), as determined from the slope of I−VI-V characteristics, is predicted to vary with temperature according to n(T)−1−1=−ρ2+ρ3/(2kT/q)n(T)^{-1}-1=-\rho_2+\rho_3/(2kT/q) where kk is Boltzmann’s constant, qq is the electric charge, and ρ2\rho_2 and ρ3\rho_3 are constants describing the variation of the mean and variance of the potential barrier distribution with junction voltage, respectively (see [23 Eq. 23]). A plot of n(T)−1−1n(T)^{-1}-1 versus T−1T^{-1} should therefore yield a line over some range of temperatures.

In addition, the built-in potential ΦBI\Phi_{BI} can be measured in two ways. From CBE−VBEC_{BE}-V_{BE} characteristics, ΦBI(CV)\Phi_{BI}(CV) can be obtained by fitting the variation of depletion capacitance with junction voltage using CBE(VBE)=CBE,0(1−VBE/ΦBI)−mC_{BE}(V_{BE})=C_{BE,0}(1-V_{BE}/\Phi_{BI})^{-m}, where CBE,0C_{BE,0} is the zero-bias junction capacitance and mm is an exponent that depends on the doping profile at the junction. [14] Using IC−VBEI_C-V_{BE} characteristics, the potential barrier energy for transport, EaE_a, relative to its value at some temperature, can be obtained by extrapolating the measured collector current to zero bias using the collector current expression IC=IS(exp⁡(qVBE/n(T)kT)−1)I_C=I_S(\exp(qV_{BE}/n(T)kT)-1) where IS=Aexp⁡(−qEa/kT)I_S=A\exp(-qE_a/kT) is the transport saturation current and AA is a constant prefactor. [1 Sec. 4.2.1] We have neglected the polynomial temperature-dependence of the prefactor as it only makes a log-scale correction to the built-in potential which does not alter our conclusions.

With the value of the transport barrier at 300 K specified as ΦBI(CV)\Phi_{BI}(CV), the temperature-dependence of the apparent built-in potential associated with charge transport ΦBI(IV)\Phi_{BI}(IV) can thus be obtained from the value of ISI_S at each temperature relative to that at the reference temperature. We note that this charge injection approach to model the current-voltage characteristics is relatively simple compared to generalized-integral charge-control relation (GICCR) models employed for HBTs. [36] However, GICCR models also exhibit discrepancies with experiment below 100 K, [37 Fig. 6.5(a)] suggesting that the physical origin is not due to the simplicity of the charge injection model.

The inhomogeneous junction theory predicts that the barrier measured in these two ways should differ in magnitude and temperature dependence owing to the fact that current depends on VBEV_{BE} exponentially while the capacitance varies with VBEV_{BE} with a weaker polynomial dependence. The barrier as determined through C−VC-V characteristics is therefore typically interpreted as the mean barrier height, while that determined from I−VI-V characteristics is often less than the mean value due to the larger contribution from low-barrier regions. [23, 38] The theory gives a relation between these barrier heights. [23 Eq. 14] Considering the form of n(T)n(T) described above, this relation is compatible with the empirical observation that ΦBI(CV)≈n(T)ΦBI(IV)\Phi_{BI}(CV)\approx n(T)\Phi_{BI}(IV) [39] (see also [23 Sec. V]).

These predictions can be tested using a cryogenic probe station to measure the IC−VBEI_C-V_{BE} and CBE−VBEC_{BE}-V_{BE} characteristics of a SiGe HBT. We note that for the CBE−VBEC_{BE}-V_{BE} characteristics, although the mechanisms of current transport in the forward active regime differ between Schottky junctions and HBTs, the electrostatics of the depletion capacitance are identical between the devices. [40 Chaps. 6 and 7] Therefore, the built-in potential can be determined by the dependence of CBEC_{BE} on VBEV_{BE} for biases for which CBEC_{BE} is dominated by the depletion capacitance. This procedure was applied to determine the built-in potential of SiGe HBTs in another study. [12]

Experimental methods

We extracted ΦBI\Phi_{BI} from CBE−VBEC_{BE}-V_{BE} and IC−VBEI_C-V_{BE} characteristics from 20–300 K on a SiGe HBT (SG13G2, IHP). The discrete transistors were probed in a custom-built cryogenic probe station. [41, 42] We employed Nickel/Tungsten probes (40A-GSG-100-DP, GGB Industries) which are suitable for probing Al pads. IC−VBEI_C-V_{BE} characteristics were performed at a constant collector voltage VCE=1V_{CE}=1 V to provide a collector current above the minimum resolution of our measurement setup (10 nA). The current range used for this fitting is limited to 0.2 mA, below the high-injection regime, to exclude effects of series resistance, self-heating and the Early and reverse Early effects. Inclusion of the reverse Early effect in the extraction of the built-in potential was found to alter the value by only a few percent as it enters the expression for the ΦBI\Phi_{BI} as a log-scale correction. ΦBI\Phi_{BI} was extracted relative to its value determined by CBE−VBEC_{BE}-V_{BE} measurements at 300 K from the zero-bias intercept of a linear fit of ln⁡(IC)\ln(I_C) versus VBEV_{BE}, and n(T)n(T) was extracted from the slope of this fit. Due to the difficulty of distinguishing periphery from area currents, we assumed that the area current is dominant following other studies of cryogenic SiGe HBTs. [5, 10, 11, 12, 17]

Following standard procedure, [12, 13] CBE−VBEC_{BE}-V_{BE} characteristics were obtained using a vector network analyzer (VNA, Keysight E5061B). In reverse-bias and low-forward bias regimes, the YY-parameters are given by Y11=gBE+jω(CBE+CBC)Y_{11}=g_{BE}+j\omega(C_{BE}+C_{BC}) and Y12=−jωCBCY_{12}=-j\omega C_{BC}, where CBCC_{BC} is the base-collector depletion capacitance. The base-emitter capacitance can therefore be expressed as CBE=(ℑ(Y11+Y12))/2πfC_{BE}=(\Im(Y_{11}+Y_{12}))/2\pi f. VBEV_{BE} was restricted to [−0.5 V,+0.5 V][-0.5\ \mathrm{V},+0.5\ \mathrm{V}] to ensure that the measured capacitance was dominated by the depletion capacitance. VBC=0V_{BC}=0 V was held constant to ensure CBCC_{BC} was constant while VBEV_{BE} was swept. The YY parameters were measured in 1–3 GHz, and the extractions were performed at 2.4 GHz. At these frequencies, it was observed that the imaginary part of Y11Y_{11} was linear in frequency, indicating purely capacitive behavior. Short-Open-Load-Through calibration was performed on a CS-5 calibration standard at each temperature, and the shunt parasitic capacitance at the input of the device was de-embedded using an OPEN structure. The intermediate-frequency bandwidth (1 kHz) and frequency points (every 0.2 GHz) were selected to limit the total sweep time to less than 15 s to avoid drift. At each bias, Y-parameters were swept across frequency and ensemble-averaged 10 times. ΦBI\Phi_{BI} was extracted from a sweep of CBEC_{BE} versus VBEV_{BE} by fitting the parameters ΦBI\Phi_{BI}, CBE,0C_{BE,0} and mm using a trust region reflective algorithm from the SciPy library. [43] ΦBI\Phi_{BI} was constrained to [0.5 V, 1.2 V], CBE,0C_{BE,0} was constrained between the minimum and maximum values of the sweep, and mm was constrained to [0, 1].

Results

Figure 1a shows the collector current ICI_C versus VBEV_{BE} at various temperatures between 20 K and 300 K. Consistent with prior findings, [5, 10, 11] the measurements exhibit deviations with drift-diffusion theory at cryogenic temperatures, with the current-voltage characteristic plateauing to a temperature-independent curve below ∼\sim60 K. We plot the extracted n(T)n(T) as Teff=n(T)TphysT_{eff}=n(T)T_{phys} versus TphysT_{phys} in Figure 1b. TeffT_{eff} is observed to plateau to ∼\sim100 K due to n(T)>1n(T)>1 at cryogenic temperatures, as has been reported previously [10].

Figure 1. (a) Measured ICI_C versus VBEV_{BE} for various temperatures. The characteristics become independent of temperature at cryogenic temperatures. (b) Teff=n(T)TphysT_{eff}=n(T)T_{phys} vs TphysT_{phys} from measurements (symbols) and diode theory (line), indicating the non-ideality of the base-emitter junction at cryogenic temperatures.

We next examine the RF characteristics. Figure 2a plots ℑ(Y11+Y12)/ω\Im(Y_{11}+Y_{12})/\omega versus ff for various VBEV_{BE} at 300 K, where ω=2πf\omega=2\pi f. A narrowed frequency range from the 1--3 GHz measurements is plotted to aid in distinguishing the curves. The de-embedded base-emitter capacitance CBEC_{BE} is directly obtained from this plot by averaging across the frequency range. Figure 2b plots the resulting CBEC_{BE} versus VBEV_{BE} at three representative temperatures across the overall voltage range along with the fitted curves. The error bars, representing the 2σ2\sigma error in CBEC_{BE}, are obtained from the 10 CBEC_{BE}--VBEV_{BE} sweeps performed at each temperature.

Figure 2. (a) Measured ℑ(Y11+Y12)/ω\Im(Y_{11}+Y_{12})/\omega (symbols) versus ff at 300 K for various VBEV_{BE} in steps of 0.1 V. The lines are guides to the eye. (b) Measured (symbols) and fitted (solid lines) CBEC_{BE} versus VBEV_{BE} at 300 K, 80 K and 20 K. As a representative example, the fit for 300 K yields ΦBI=0.83\Phi_{BI}=0.83 V and m=0.10m=0.10.

These data are next analyzed to obtain ΦBI\Phi_{BI} from the ICI_C--VBEV_{BE} and CBEC_{BE}--VBEV_{BE} characteristics according to the procedures in § 2 B. At 300 K, ΦBI(CV)\Phi_{BI}(CV) is found to be 0.83 V, in good agreement with [12]. This value is specified as the room temperature value for ΦBI(IV)\Phi_{BI}(IV) to facilitate comparison at other temperatures. Figure 3a plots the ΦBI\Phi_{BI} from both measurements versus TphysT_{phys}. For ΦBI(CV)\Phi_{BI}(CV), the error bars represent the 2-σ\sigma error in ΦBI\Phi_{BI}, obtained by performing fits to 100 CBEC_{BE}--VBEV_{BE} sweeps with errors randomly determined based on a normal distribution defined by the uncertainty in the measured CBEC_{BE}. The extracted ΦBI(CV)\Phi_{BI}(CV) is observed to weakly increase with decreasing temperature, consistent with observations for similar HBT devices [12] and Schottky diodes [39]. In contrast, ΦBI(IV)\Phi_{BI}(IV) exhibits a qualitatively stronger dependence on temperature than

Figure 3. (a) Built-in potential ΦBI\Phi_{BI} versus physical temperature from CBE−VBEC_{BE}-V_{BE} (black circles) and IC−VBEI_C-V_{BE} (orange triangles) measurements. Also plotted is n(T)ΦBI(IV)n(T)\Phi_{BI}(IV) (green squares) which is predicted to agree with ΦBI(CV)\Phi_{BI}(CV). [23] Good agreement is observed. (b) n(T)−1−1n(T)^{-1}-1 versus inverse physical temperature T−1T^{-1} for measured data along with a linear fit to the data in 40-100 K following the prediction in [23]. Data obtained from [10 Fig. 5.8] are also shown.

ΦBI(CV)\Phi_{BI}(CV) and differs markedly in magnitude at cryogenic temperatures, as observed previously for Schottky diodes [13, 39] (also compare to [34], Fig. 3). The variation with temperature of ΦBI(IV)\Phi_{BI}(IV) is significantly stronger than that of the emitter and base band gaps, [14] suggesting another mechanism is responsible for the observed temperature trend.

We now examine the agreement between the data and the predictions from the inhomogeneous junction theory of [23]. First, qualitatively, ΦBI(CV)\Phi_{BI}(CV) and ΦBI(IV)\Phi_{BI}(IV) are predicted to differ, with

ΦBI(IV)\Phi_{BI}(IV) expected to exhibit a stronger temperature dependence and be smaller in magnitude than ΦBI(CV)\Phi_{BI}(CV). This behavior is observed in Figure 3a. More quantitatively, for the predicted temperature-dependence of n(T)n(T) from the theory, it is expected that ΦBI(CV)≈n(T)ΦBI(IV)\Phi_{BI}(CV)\approx n(T)\Phi_{BI}(IV) [23 Sec. V]. The product n(T)ΦBI(IV)n(T)\Phi_{BI}(IV) is also plotted in Figure 3a, demonstrating good agreement with ΦBI(CV)\Phi_{BI}(CV).

Second, [23 Eq. 23] predicts that n(T)−1−1n(T)^{-1}-1 versus T−1T^{-1} should be a straight line over some range of temperatures. Figure 3b plots this quantity for the present device and other devices with data obtained from [10 Fig. 5.8]. For all the devices, the expected trend is observed over a temperature range which is comparable in relative width to that in [23 Fig. 9]. For the older-generation devices,

the linear trend is observed from 18 – 100 K. For the present device, a linear regime is found from 40 – 100 K, while a deviation is noted at 20 K. These data are consistent with the absence of tunneling in the older devices and a non-negligible direct tunneling current in the present device. Other explanations for the deviation could include the assumption of temperature-independent barrier properties in the inhomogeneous barrier theory. However, overall the experimental trends are in good qualitative agreement with the theoretical predictions.

Semi-quantitative information regarding the variation of the barrier height variance with bias for the present device can be obtained from the linear fit in Figure 3b. If ρ2+ρ3/(2kT/q)≪1\rho_{2}+\rho_{3}/(2kT/q)\ll1, the theory of [23] reduces to the T0T_{0} model for non-ideal junctions which has been extensively studied in the Schottky junction literature. [19, 22, 23] In this case, the slope of the linear fit in Figure 3b is simply T0T_{0}. Performing this fit for the present data yields T0≈30T_{0}\approx30 K, a value which is generally compatible with values for Schottky diodes compiled in [23]. Using [23 Eq. 33], this value can be recast in terms of the narrowing of the potential barrier height distribution with increasing bias using ρ3≈−2kT0/q\rho_{3}\approx-2kT_{0}/q. We obtain a value ρ3=−5.2\rho_{3}=-5.2 mV. The magnitude of this value indicates that changes in standard deviation of the potential barrier height distribution with base-emitter bias which are less than a percent of the mean barrier height are sufficient to account for the observed electrical anomalies.

Discussion

The agreement of our data with the predictions of the inhomogeneous barrier theory suggests that lateral inhomogeneities in the base-emitter junction potential could contribute to the cryogenic electrical anomalies. Additional evidence for the barrier inhomogeneity hypothesis could be obtained using techniques such as ballistic emission electron microscopy which directly measures the spatial profile of the built-in potential. [33] However, applying this method to SiGe HBTs would require specialized samples to be prepared which are compatible with the measurement technique.

The materials-scale origin of the inhomogeneities in HBTs could be Ge clusters [44] or electrically active carbon defects [45]. Non-uniform Ge content over a few nanometers in SiGe p-wells with Ge concentration ≥30%\ge30\% has been reported to lead to the degradation of electrical properties like hole mobility. [44] Trap states associated with C impurities have also been detected in modern HBTs. [45] With Ge concentrations for modern HBTs being on the order of 30% [11] and C doping on the order of 102010^{20} cm−3^{-3}, [1] these defects lead to an inhomogeneous base-emitter junction potential.

If the presence of spatial inhomogeneities across the emitter area is verified, a less aggressive Ge doping concentration and profile, especially in narrow-base SiGe HBTs, could decrease the concentration of these imperfections and thereby lead to a more uniform base-emitter junction potential. However, care would need to be taken to avoid negatively impacting the high-frequency properties of the device. Additionally, direct tunneling may pose a fundamental obstacle to improving the cryogenic electrical ideality of highly-scaled devices. Further study is needed to distinguish the various mechanisms and identify the limits to cryogenic electrical ideality and hence microwave noise performance.

Conclusion

We have reported a characterization of the collector-current ideality factor and built-in potential versus temperature of a SiGe HBT. The observed trends with temperature and between measurement techniques agree with a theory of electrical transport at a potential barrier with a Gaussian distribution of barrier heights, suggesting that barrier inhomogeneities may contribute to cryogenic electrical non-idealities in SiGe HBTs. This work advances efforts to improve the cryogenic microwave noise performance of SiGe HBTs.

Acknowledgments

The authors thank Akim Babenko, John Cressler, Nicolas Derrier, Xiaodi Jin, Pekka Kangaslahti, Holger Rücker, Michael Schröter, and Sander Weinreb for useful discussions. This work was supported by NSF Award Number 1911926 and by JPL PDRDF Project Number 107978.

Author Declarations

Conflict of Interest

The authors have no conflicts to disclose.

Data Availability

The data that support the findings of this study are available from the corresponding author upon reasonable request.

References

  1. [1]J. D. Cressler and G. Niu, Silicon-germanium heterojunction bipolar transistors (Artech house, 2003).
  2. [2]P. Chevalier, M. Schroter, C. R. Bolognesi, V. D’Alessandro, M. Alexandrova, J. Bock, R. Flickiger, S. Fregonese, B. Heinemann, C. Jungemann, R. Lovblom, C. Maneux, O. Ostinelli, A. Pawlak, N. Rinaldi, H. Rucker, G. Wedel, and T. Zimmer, Si/SiGe:C and InP/GaAsSb Heterojunction Bipolar Transistors for THz Applications, Proceedings of the IEEE 105, 1035 (2017).DOI
  3. [3]W. T. Wong, M. Hosseini, H. Rucker, and J. C. Bardin, A 1 mW cryogenic LNA exploiting optimized SiGe HBTs to achieve an average noise temperature of 3.2 K from 4-8 GHz, in 2020 IEEE/MTT-S International Microwave Symposium (IMS) (IEEE, 2020) pp. 181–184.DOI
  4. [4]J. C. Bardin, S. Montazeri, and S. W. Chang, Silicon germanium cryogenic low noise amplifiers, in Journal of Physics: Conference Series, Vol. 834 (IOP Publishing, 2017) p. 012007.DOI
  5. [5]H. Ying, J. Dark, A. P. Omprakash, B. R. Wier, L. Ge, U. Raghunathan, N. E. Lourenco, Z. E. Fleetwood, M. Mourigal, D. Davidovic, and J. D. Cressler, Collector Transport in SiGe HBTs Operating at Cryogenic Temperatures, IEEE Transactions on Electron Devices 65, 3697 (2018).DOI
  6. [6]J. C. Bardin, D. H. Slichter, and D. J. Reilly, Microwaves in quantum computing., IEEE journal of microwaves 1, 10.1109/JMW.2020.3034071 (2021).DOI
  7. [7]G. L. Patton, S. S. Iyer, S. L. Delage, S. Tiwari, and J. M. Stork, Silicon-Germanium-Base Heterojunction Bipolar Transistors By Molecular Beam Epitaxy, IEEE Electron Device Letters 9, 165 (1988).
  8. [8]A. J. Joseph, J. D. Cressler, and D. M. Richey, Operation of SiGe Heterojunction Bipolar Transistors in the Liquid-Helium Temperature Regime, IEEE Electron Device Letters 16, 268 (1995).DOI
  9. [9]D. M. Richey, A. J. Joseph, J. D. Cressler, and R. C. Jaeger, Evidence for non-equilibrium base transport in Si and SiGe bipolar transistors at cryogenic temperatures, Solid-State Electronics 39, 785 (1996).DOI
  10. [10]J. C. Bardin, Silicon-Germanium Heterojunction Bipolar Transistors For Extremely Low-Noise Applications, Ph.D. thesis, California Institute of Technology (2009).DOI
  11. [11]H. Rucker, J. Korn, and J. Schmidt, Operation of SiGe HBTs at cryogenic temperatures, Proceedings of the IEEE Bipolar/BiCMOS Circuits and Technology Meeting , 17 (2017).DOI
  12. [12]X. Jin, M. Muller, P. Sakalas, A. Mukherjee, Y. Zhang, and M. Schroter, Advanced SiGe:C HBTs at Cryogenic Temperatures and Their Compact Modeling with Temperature Scaling, IEEE Journal on Exploratory Solid-State Computational Devices and Circuits 7, 175 (2021).DOI
  13. [13]W. Mönch, Semiconductor Surfaces and Interfaces (Springer Berlin, Heidelberg, 2001) pp. 385–481.
  14. [14]S. M. Sze, Y. Li, and K. K. Ng, Physics of semiconductor devices (John wiley & sons, 2021).
  15. [15]D. Davidović, H. Ying, J. Dark, B. R. Wier, L. Ge, N. E. Lourenço, A. P. Omprakash, M. Mourigal, and J. D. Cressler, Tunneling, current gain, and transconductance in silicon-germanium heterojunction bipolar transistors operating at millikelvin temperatures, Physical Review Applied 8, 1 (2017).DOI
  16. [16]N. R. Naik and A. J. Minnich, Quasiballistic electron transport in cryogenic SiGe HBTs studied using an exact, semi-analytic solution to the Boltzmann equation, Journal of Applied Physics 130, 174504 (2021).DOI
  17. [17]M. Schroter and X. Jin, A physics-based analytical formulation for the tunneling current through the base of bipolar transistors operating at cryogenic temperatures, IEEE transactions on electron devices 70, 247 (2023).DOI
  18. [18]R. Hackam and P. Harrop, Electrical Properties of Nickel-Low-Doped n-Type Gallium Arsenide Schottky-Barrier Diodes, IEEE Transactions on Electron Devices 19, 1231 (1972).DOI
  19. [19]F. A. Padovani and G. G. Sumner, Experimental study of gold-gallium arsenide schottky barriers, Journal of applied physics 36, 3744 (1965).DOI
  20. [20]A. Saxena, Forward current-voltage characteristics of schottky barriers on n-type silicon, Surface science 13, 151 (1969).DOI
  21. [21]S. Ashok, J. Borrego, and R. Gutmann, Electrical characteristics of GaAs MIS schottky diodes, Solid-state electronics 22, 621 (1979).DOI
  22. [22]R. T. Tung, Electron transport at metal-semiconductor interfaces: General theory, Physical Review B 45, 13509 (1992).pubmed.ncbi.nlm.nih.gov/10001439
  23. [23]J. H. Werner and H. H. Güttler, Barrier inhomogeneities at Schottky contacts, Journal of Applied Physics 69, 1522 (1991), https://pubs.aip.org/aip/jap/article-pdf/69/3/1522/8018481/1522_1.online.pdf.DOI
  24. [24]J. L. Freeouf, T. N. Jackson, S. E. Laux, and J. M. Woodall, Effective barrier heights of mixed phase contacts: Size effects, Applied physics letters 40, 634 (1982).DOI
  25. [25]Y. Song, R. Van Meirhaeghe, W. Laflère, and F. Cardon, On the difference in apparent barrier height as obtained from capacitance-voltage and current-voltage-temperature measurements on al/p-InP schottky barriers, Solid-state electronics 29, 633 (1986).DOI
  26. [26]V. A. Johnson, R. N. Smith, and H. J. Yearian, D.c. characteristics of silicon and germanium point contact crystal rectifiers. part II. the multicontact theory, Journal of applied physics 21, 283 (1950).DOI
  27. [27]R. T. Tung, Schottky-barrier formation at single-crystal metal-semiconductor interfaces, Physical Review Letters 52, 461 (1984).
  28. [28]R. J. Hauenstein, T. E. Schlesinger, T. C. McGill, B. D. Hunt, and L. J. Schowalter, Schottky barrier height measurements of epitaxial NiSi2 on si, Applied physics letters 47, 853 (1985).DOI
  29. [29]R. Tung, A. Levi, J. Sullivan, and F. Schrey, Schottky-barrier inhomogeneity at epitaxial NiSi2 interfaces on si(100)., Physical Review Letters 66, 72 (1991).pubmed.ncbi.nlm.nih.gov/10043145
  30. [30]H. v. Känel, T. Meyer, and M. Klemenc, Ballistic-electron-emission microscopy on epitaxial silicides, Japanese journal of applied physics 37, 3800 (1998).
  31. [31]H. von Känel and T. Meyer, Spectroscopy on MBE-grown interfaces with high spatial resolution, Thin solid films 306, 214 (1997).
  32. [32]W. Kaiser and L. Bell, Direct investigation of subsurface interface electronic structure by ballistic-electron-emission microscopy., Physical Review Letters 60, 1406 (1988).
  33. [33]M. Prietsch, Ballistic-electron emission microscopy (beem): Studies of metal/semiconductor interfaces with nanometer resolution, Physics Reports 253, 163 (1995).DOI
  34. [34]J. H. Werner and H. H. Güttler, Transport properties of inhomogeneous schottky contacts, Physica Scripta T39, 258 (1991).DOI
  35. [35]U. Rau, H. H. Güttler, and J. H. Werner, The ideality of spatially inhomogeneous schottky contacts, MRS Proceedings 260, 245 (1992).DOI
  36. [36]A. Pawlak and M. Schroter, An improved transfer current model for RF and mm-wave SiGe(c) heterojunction bipolar transistors, IEEE transactions on electron devices 61, 2612 (2014).DOI
  37. [37]X. Jin, Characterization and Compact Modeling of Silicon-Germanium Heterojunction Bipolar Transistors from Room to Cryogenic Temperatures, Ph.D. thesis, TU Dresden (2023).
  38. [38]I. Ohdomari, T. S. Kuan, and K. N. Tu, Microstructure and schottky barrier height of iridium silicides formed on silicon, Journal of applied physics 50, 7020 (1979).DOI
  39. [39]A. S. Bhuiyan, A. Martinez, and D. Esteve, A new Richardson plot for non-ideal Schottky diodes, Thin Solid Films 161, 93 (1988).DOI
  40. [40]J. del Alamo, Integrated Microelectronic Devices: Physics and Modeling, 1st ed. (Pearson, 2017) p. 880.
  41. [41]B. Gabritchidze, K. Cleary, J. Kooi, I. Esho, A. C. Readhead, and A. J. Minnich, Experimental characterization of temperature-dependent microwave noise of discrete HEMTs: Drain noise and real-space transfer, in 2022 IEEE/MTT-S International Microwave Symposium-IMS 2022 (IEEE, 2022) pp. 615–618.DOI
  42. [42]D. Russell, K. Cleary, and R. Reeves, Cryogenic probe station for on-wafer characterization of electrical devices, Review of Scientific Instruments 83, 044703 (2012).DOI
  43. [43]P. Virtanen, R. Gommers, T. E. Oliphant, M. Haberland, T. Reddy, D. Cournapeau, E. Burovski, P. Peterson, W. Weckesser, J. Bright, S. J. van der Walt, M. Brett, J. Wilson, K. J. Millman, N. Mayorov, A. R. J. Nelson, E. Jones, R. Kern, E. Larson, C. J. Carey, I. Polat, Y. Feng, E. W. Moore, J. VanderPlas, D. Laxalde, J. Pertkold, R. Cimrman, I. Henriksen, E. A. Quintero, C. R. Harris, A. M. Archibald, A. H. Ribeiro, F. Pedregosa, P. van Mulbregt, and SciPy 1.0 Contributors, SciPy 1.0: Fundamental Algorithms for Scientific Computing in Python, Nature Methods 17, 261 (2020).
  44. [44]R. A. Kiehl, P. E. Batson, J. O. Chu, D. C. Edelstein, F. F. Fang, B. Laikhtman, D. R. Lombardi, W. T. Masselink, B. S. Meyerson, J. J. Nocera, A. H. Parsons, C. L. Stanis, and J. C. Tsang, Electrical and physical properties of high-Ge-content Si/SiGe p-type quantum wells, Physical Review B 48, 11946 (1993).pubmed.ncbi.nlm.nih.gov/10007538
  45. [45]J. Raoult, F. Pascal, C. Delseny, M. Marin, and M. J. Deen, Impact of carbon concentration on 1f noise and random telegraph signal noise in SiGe:C heterojunction bipolar transistors, Journal of Applied Physics 103, 114508 1 (2008).DOI

Paper details

vlnc:W_94cajzvu
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents