WorksPhysics and Astronomy
Time-averaged velocity and scalar fields of the flow surrounding a group of cylinders
Abstract
We examine the characteristics of mean flow and scalar concentration characteristics of a turbulent boundary layer flow impinging on a cluster of tall obstacles (which can also be interpreted as a porous obstruction). The cluster is created with a group of cylinders of diameter and height arranged in a circular patch of diameter .The solidity of the patch/obstruction is defined by (the total planar area covered by cylinders), which is systematically varied () by increasing the number of cylinders in a patch (). A point source is placed at ground level upstream of the patch and its transport around the patch is examined. Time-averaged velocity and scalar fields, obtained from simultaneous planar PIV-PLIF (particle image velocimetry-planar laser-induced fluorescence) measurements, reveal that the characteristics of wake and flow above porous patches are heavily influenced by . In particular, we observe that the horizontal and vertical extent of the wake and scalar concentration downstream of the patches decreases and increases with , respectively. Here, the recirculation bubble is shifted closer to the trailing edge of the patches as increases, limiting the flow from convecting downstream, decreasing the scalar concentration and virtually extending' the patch in streamwise direction. As the bubble forms in the trailing edge, vertical bleeding increases and hence the concentration increases above patch where the cylinders appear to be extend' vertically towards the freestream.
Impact Statement
Canopy flow covers extensive phenomena encountered in both nature and engineering applications. The characteristics of canopies (also referred to as porous obstructions) is known to affect the mixing, momentum, and scalar (e.g. mass and heat) exchange processes in the flow. Examples include flow around urban areas, wind/tidal farms, patches of roughness in ship hulls, in-line heat-exchangers among various others. In almost all these applications, the patch of obstacles/roughness is typically characterised by its geometric properties such as solidity (frontal and plan) or porosity and it is important to understand the flow/scalar characteristics as well as transport processes for varied geometric parameters. For instance, an urban canopy with given distribution of buildings and a pollutant source at ground level could result in different wake/dispersion characteristics depending on the frontal or plan solidity of distribution. This study attempts to carry out simplified experiments that will enable us to understand the intricacies of scalar-momentum transport around such canopies and allow us to build useful models for engineering design and/or prediction for engineering and environmental flows.
Introduction
Canopy flow refers to a scenario where a boundary layer develops over and around a porous surface/obstruction. Examples of such phenomenon are abound in both nature and engineering applications, including but not limited to: flows past aquatic and terrestrial vegetations, atmospheric boundary layers developing over forests, clusters of tall buildings in cities, and wind/tidal farms, which consist of arrays of wind/tidal turbines. These obstructions are known to affect the scalar, momentum, and energy transport process in the flow within the canopy and downstream of the canopies. Aquatic vegetations, for example, provide shielding [18], affect the sediment formation and erosion (De Langre, 2008; Nepf, 2012a,b; Tinoco and Coco, 2016), and also carbon sequestration in coastal ecosystems [20]. Urban and vegetation canopies induce coherent, multi-scale turbulent motions in the atmospheric boundary layer [17, 16, 13, 15, 21], which governs flow mixing, momentum, heat and mass exchange within the layer [33, 12, 30], including pollutants and other chemical compounds [31, 2]. While the configuration and tuning of turbines in wind/tidal farms are vital in maximising power output [42, 22], they may also alter the meteorological pattern and ecosystem of the installation sites. For example, installation of wind turbines has been shown to affect the heat distribution and humidity of the surrounding air [3, 32], while wakes generated by tidal turbines can potentially modify sedimentation process and bacterial population in estuarine waters [1]. Considering its extensive industrial applications and environmental impacts, understanding the transport mechanism of the flow surrounding porous obstructions is, therefore, essential.
Previous studies on porous obstructions (such as examples given above) typically involved some simplifications from real-life conditions. The obstruction may be simplified as an array of cylinders mounted on an isolated patch with an incoming flow upstream of the cylinders (illustrated in Figure 1). Numerical simulations and experiments have been conducted on the flow surrounding such cylindrical array [4, 23, 24, 43, 38, 28, 34, 9, 46, 7, 8], where the cylinders are as tall as, or protruding from, a free surface, as commonly observed in emergent aquatic vegetations. Here, the flow is dominated by Kármán vortex street in wall-normal axis trailing behind the cylinders and thus can be considered two-dimensional [37, 27]. A more general approach is to fully submerge the cylinders in the flow such that (Figure 1b). Studies have been conducted for cylinders attached to a bottom wall (as in Figure 1b, see also [9, 37, 27]) and/or suspended from a free surface [29, 40, 45]. In either cases, the patch is considered as 3-D, as flow mixing occurs on the sides of, downstream of, and above the body. [37, 45, 27] have identified three mechanisms in which the flow may escape (‘bleed’) from a fully submerged porous obstruction: (i) the lateral bleeding from the interior of the patch to the sides (spanwise direction, see Figure 1a), (ii) the trailing edge bleeding, which is responsible in the formation of wake downstream of the body (Figure 1a), and (iii) the vertical bleeding, in which the flow escapes from the interior to the top surface of the patch and towards the freestream (Figure 1b).

Figure 1. Illustrations of (a) lateral and trailing edge bleeding, and (b) vertical bleeding of cylindrical arrays on a circular patch. is the incoming boundary-layer velocity, whose thickness is , and is the height of the cylinders.
It has been reported that the solidity of a porous obstruction is a critical parameter in determining drag [24, 37, 8, 45], the structure of wake formed by the obstruction [4, 28, 46, 9, 7, 8, 45, 27], scalar dispersion [23, 43, 38], and sediment disposition [9, 7]. For the cylindrical array shown in Figure 1, the solidity is measured in terms of the planar area covered by cylinders per total surface, (also commonly referred to as the solid volume fraction), where is the number of cylinders in a circular patch, is the diameter of the circular patch, and is the diameter of the cylinder (see Figure 2a,Figure 2d for graphical descriptions of and ). It has been observed by Nicolle and Eames [28]; Taddei et al. [37]; Zhou and Venayagamoorthy [45] that total drag of the patch increases with the increasing then drops for a solid obstruction (, Figure 2d). Higher patch solidity also yields shorter and taller wake (in streamwise and wall-normal direction, respectively, see Nicolai et al., [27]) in the trailing edge, and increases both lateral and vertical bleeding (Zhou and Venayagamoorthy, [45], see also Figure 1). Further, it has been reported in Nicolle and Eames [28] that at low () each cylinder in an array behaves as a single obstruction, and as the solidity increases to the cylindrical array behaves closer to a solid obstruction whose size is equal to that of the patch (, Figure 2d). Within the range of moderate solidity (), suppression of vortex street formation downstream of 2-D porous patches has been observed. In its place is a steady wake (constant velocity) region, which is a consequence of flow bleeding. Zong and Nepf [46] and Chen et al. [9] showed that the streamwise length of this steady wake region scales on , where is the frontal area per unit volume . Similarly, scaling by and have also been observed in Rominger and Nepf [34] for a square patch and Chen et al. [10] for a fully submerged patch, respectively, where is the half-width of the patch.
Figure 2. Illustration of cylinder array test cases: (a) C39, (b) C64, (c) C133, and (d) the solid case (CS) in – plane (top view), is cylinder diameter and is the circular patch diameter. (e) Mean streamwise velocity (○) and variance of velocity fluctuation (●) of the smooth-wall turbulent boundary-layer (TBL) case as functions of wall-normal location at , where is the momentum thickness. Dashed line (– –) is , solid line (—) is the DNS results of Sillero et al. [36] at , filtered according to the spatial resolution of the PIV measurements (Lee et al. [19]). Data are downsampled for clarity.
Although the characteristics of the wake and drag of a porous obstruction shown in Figure 1 have been discussed in details for both 2-D and 3-D patches, an element that is still missing from these analyses is the intricacy between bleeding and scalar transport in 3-D porous patches. So far, discussions about scalar transport are limited to lateral and longitudinal dispersion in 2-D patches (White and Nepf, [43]; Tanino and Nepf, [38]), sediment deposition (Chen et al., [9]; Tinoco and Coco, [39]), qualitative flow visualisation using dye injection (Ball et al., [4]; Rominger and Nepf, [34]; Zong and Nepf, [46]), and non-simultaneous velocity and scalar measurements due to limitations of the experimental facilities (Nepf, [24]; Tanino and Nepf, [38]). Here, a 3-D porous patch serves as a more realistic model of urban landscapes, vegetation canopies, and wind farms, which are typically subsumed within the atmospheric boundary layer. Inclusion of scalar measurements (in addition to the velocity components) has many potential benefits, for example: in air pollution studies, where one might consider cluster of densely populated urban landscape as a porous obstruction and the pollutant as scalar, or in studies about sediment deposition in ocean beds.
In this study we aim to address the following question: given a point source of scalar located at ground level just upstream of 3-D porous patches, what are the flow and scalar characteristics in the wake and above the patches for various solidities? To answer this question, we conduct a parametric study of turbulent boundary layers impinging on an array of cylinders mounted on a circular patch (see Figure 1). A point source upstream of the patch is created by releasing a passive fluorescent dye. The solidity is varied by systematically increasing the number of cylinders in the patch, such that . This covers both medium and high solidity range described in Nicolle and Eames [28]. The axis system corresponds to the streamwise, wall-normal, and spanwise direction, respectively. Simultaneous planar PIV-PLIF measurements in – plane provide the instantaneous streamwise–wall-normal velocity components and , respectively, and scalar concentration field , which can be decomposed further into their time-average and fluctuation about the mean
It should be noted that due to the choice of the measurement plane, discussion about flow bleeding in the current study is limited only to the trailing edge and vertical bleeding (Figure 1).
Experimental setup
Test cases
Experiments are carried out in the closed loop water flume at the University of Southampton. The test section has the size of 6250 mm 1200 mm (length width). In all measurements, the water level is kept constant at 600 mm and the freestream velocity is set to m s.
A circular patch with a diameter () of 100 mm is mounted on the floor of the tunnel at 5500 mm downstream of the test section entrance, which corresponds to the patch Reynolds number , where m s is the kinematic viscosity of water at 20°C. The patch constitutes an array of rigid cylinders, each has the diameter of mm and height mm (Figure 1b and Figure 2a,Figure 2d). The cylinders are arranged along concentric, evenly-spaced circles whose axis is at the centre of the circular patch, such that the distance between two consecutive cylinders is constant within the patch (see Figure 2a–Figure 2c). The solidity of the patch is parametrically varied by gradually increasing the number of cylinders while keeping and constant. Table 1 and Figure 2(a–Figure 2c) show three different circular patches: C39, C64, C133, which correspond to , 64, 133, which cover a range of patch density of (). A solid obstruction case, i.e. a cylinder covering the entire circular patch (such that and ), is included in addition to the porous cases as case ‘CS’ in Table 1 and Figure 2(d). The solid cylinder in case CS has an equal height to the cylinder arrays in other test cases.
| Cases | Colour | PIV | PLIF | FOV 1 | FOV 2 | FOV 3 | |||||
| C39 | 39 | 0.05 | 0.3 | 0.098 | 2.483 | ● | ✓ | ✓ | ✓ | ✓ | ✓ |
| C64 | 64 | 0.05 | 0.3 | 0.160 | 4.074 | ● | ✓ | ✓ | ✓ | ✓ | ✓ |
| C133 | 133 | 0.05 | 0.3 | 0.333 | 8.467 | ● | ✓ | ✓ | ✓ | ✓ | ✓ |
| CS | 1 | 1 | 0.3 | 1 | 1.273 | ● | ✓ | ✓ | ✓ | ✓ | ✗ |
| TBL | – | – | – | – | – | – | ✓ | ✗ | ✓ | ✓ | ✗ |
Table 1. List of cylinder array test cases. is the number of cylinders in a patch, and are the diameters of the cylinders and the patch, respectively, is the height of the cylinders, is patch solidity, and is the frontal area per unit volume. ‘PIV’ and ‘PLIF’ columns show the availability of PIV and PLIF images of each test case. The last three columns show the availability of those images in each FOV.
Validation with smooth-wall turbulent boundary layer
A smooth-wall turbulent boundary layer (‘TBL’) case is first tested to validate PIV measurements in the present study. The measurement is conducted in the same test section as other test cases by removing the circular patch. This flow has the Reynolds number (based on momentum thickness ) of and friction Reynolds number , where mm is the boundary-layer thickness, m s is the friction velocity for this case, is the wall shear stress, and kg m is the density of water at 20°C. Figure 2(e) shows the profiles of mean streamwise velocity and the variance of velocity fluctuations as functions of wall-normal location , where subscript ‘+’ denotes the viscous scaling and the viscosity lengthscale mm. The logarithmic region of the mean velocity collapses to the line , where is the von Kármán constant and the is the log-law shift (Schlichting and Gersten, [35]). The variance is in good agreement with that obtained from direct numerical simulation (DNS) of Sillero et al. [36] at . Note that the DNS results presented in Figure 2(e) are filtered according to the spatial resolution of the PIV measurements (Lee et al., [19]), in streamwise and wall-normal directions, respectively.
Particle image velocimetry (PIV) and planar laser-induced fluorescence (PLIF)
For simultaneous planar PIV and PLIF measurements, the measurement domain is located in the streamwise–wall-normal (–) plane, slicing the centerline of the circular patch (Figure 3) and illuminated by Nd:YAG 100 mJ pulsed laser. The measurement domain is created by combining 3 successive experiments in field-of-view (FOV) 1, FOV 2, and FOV 3, which extends downstream of the circular patch. Dashed lines in Figure 3 illustrate these FOVs and the overlaps between each FOV. It should be noted that although the PIV and PLIF measurements are conducted simultaneously in each FOV, these measurements are not conducted simultaneously between FOV 1, 2 and 3. PIV and PLIF images are recorded first in FOV 1, then the cameras and optics are traversed downstream to form FOV 2, then FOV 3. Measurements are conducted in all three FOVs for the cylindrical array cases (C39, C64, and C133), and only the first two FOVs for the baseline cases (CS and TBL, see Table 1).

Figure 3. Contours of instantaneous (a) streamwise velocity and (b) scalar concentration (in logarithmic scale) of case C39, obtained from (a) PIV and (b) PLIF measurements, respectively, where is the incoming velocity at half-height of the cylinders. Dashed lines show the extent of FOV 1, 2 and 3. Black rectangles illustrate the cylinder array of height mounted on a circular patch. The origin is at the centre of the patch and is on the floor of the tunnel. Measurement data are not available in the hatched regions (between the cylinders). In (b), blue arrow shows the location of the scalar point source.
In each FOV, PIV images are recorded by a pair of 4 MP CMOS cameras, equipped with wavelength filters to filter out the PLIF signal. As many as 3000 image pairs are acquired for each case at the rate of 4 Hz, which corresponds to the boundary-layer turnover rate of . The timing between a pair of PIV images is ms (). Image cross-correlation and post-processing of the resulting velocity vectors are conducted using a commercial software (DaVis, LaVision GmbH), with the final window size of 24 × 24 pixels (50% overlap) and image pixel size of 15 pixels/mm, which corresponds to the spatial resolution of for case TBL. Each FOV has the size of 253 mm × 126 mm (), which approximately extends 2.5 times the patch diameter () in streamwise and in height. When the three FOVs are stitched together, the total length in is 689 mm ().
For PLIF measurements, a point source is created upstream of the circular patch by injecting Rhodamine 6G dye solution (Schmidt number ) to the flow at the rate of 30 cc/min. The dye is supplied by gravity through a thin tube (3 mm diameter) embedded at the floor of the tunnel at 45° angle. The tube is located at 125 mm upstream from the centre the patch (, see Figure 3b). PLIF images are acquired using a 5.5 MP 16-bit sCMOS camera equipped with a wavelength filter to block all light except the PLIF signal ([41]). To reduce the uncertainty of the scalar concentration measurements, the laser power is recorded at each pulse by an in-line power energy monitor. To maximise the signal-to-noise ratio of the scalar concentration, the concentration of the dye solution at point source is varied based on the location of the FOV relative to the point source. For FOV 1 (closest to the point source), mg/L, while for FOV 2 and FOV 3, mg/L. The measured scalar concentration presented in this study is normalised by .
Results and discussions
Trailing edge bleeding, the extent of the wake and scalar concentration
Figures 4(a–d) show the contours of time-averaged streamwise velocity for all porous test cases and the solid case (CS) listed in Table 1. The contours are normalised by , which is defined as the incoming, undisturbed streamwise velocity upstream of the patch () at the half-height of the cylinder, . The figures show the formation of wake for all porous and solid cases in the form of velocity deficit downstream of the patches. The magnitude of the deficit is significant, which signals the presence of patch-sized flow phenomena [37] as opposed to those of individual cylinders observed in patches with low solidity [9, 7, 37, 27]. In Figure 4(b–Figure 4c), blue-shaded contours show , which correspond to the recirculation of the flow downstream of the patch. The strength of the recirculating flow appears to be affected by the solidity of the patch: recirculation is not apparent in case C39 (case with the lowest solidity, Figure 4a), a weak recirculation then appears in case C64 (Figure 4b), which grows stronger in case C133 (Figure 4c). It is also noted that the recirculation bubbles are shifted downstream as solidity decreases. In case C64 (Figure 4b) the bubble is observed at , while in case C133 (Figure 4c) and the solid case CS (Figure 4d), the bubbles form immediately at the trailing edge of the patches (). Similar phenomenon has been observed in 2-D patches [7], 3-D patches [37, 45], and porous plates [6]. Contours of positive (upward) wall-normal velocity above the patches are shown in solid lines in Figure 5. For the porous cases in Figure 5(a–Figure 5c), vertical bleeding is apparent above the patches, characterised by the contours of at and . This will be left for further discussion in § 4.2.

Figure 4. Contours of time-averaged streamwise velocity of case: (a) C39, (b) C64, (c) C133, and (d) CS. Lines are the time-averaged spanwise vorticity with the following contour levels: (——) and (——).
Figure 5. Contours of time-averaged scalar concentration (in logarithmic scale) of case: (a) C39, (b) C64, (c) C133, and (d) CS. Lines are the time-averaged wall-normal velocity with the following contour levels: (——) and (——). Measurement data are not available in the hatched regions.
Superimposed with the contours of in Figure 4(a–Figure 4d) are the contours of time-averaged spanwise vorticity normalised by . Black solid lines are the contours of (clockwise) and the blue lines (counter-clockwise). Negative show the development of shear layers forming above and downstream of the patches, which appear to be stronger (higher in magnitude) as solidity increases. Similar to the observation in [37], here we also observe the elevation of the shear layer further upward from the patches as solidity increases (compare, for example, Figure 4c to Figure 4a,Figure 4b). The lift-off is attributed to vertical bleeding from the interior of the patches, which is noticeably absent in the solid case CS (Figure 4d) where there is no vertical bleeding.
Figures 5(a–d) show the contours of time-averaged scalar concentration (normalised by the concentration at the source and presented in logarithmic scale) for all porous test cases and the solid case (CS) listed in Table 1. Dark-shaded contours in Figure 5(a–Figure 5c) illustrate how the scalar permeates through and downstream of the patches. With less obstructions to block the flow, high scalar concentration (purple-shaded) is observed downstream of the C39 and C64 patch in Figure 5(a,Figure 5b), respectively. As blockage () increases, TE bleeding decreases and consequently, the downstream concentration decays (see C133 patch, Figure 5c). Instead, the scalar escapes the patch by means of vertical bleeding, as shown by higher scalar concentration above the patch () in Figure 5(c). As reaches 1 (solid case), TE and vertical bleeding are non-existent, as evidenced by above the patch and low magnitude of downstream of the patch (Figure 5d). Here, the observed concentration is mainly the result of flow mixing in the wake instead of the scalar permeating through the patch.
Figures 4 and 5 show the dependency of wake and scalar concentration downstream of the porous bodies as a result of TE bleeding. We attempt to measure the extent of the wake by utilising a similar method in [27]. First, we define velocity defect as , where is the incoming boundary layer velocity profile upstream of the patch (at ), and arbitrarily choose a threshold for the magnitude of as a wake definition. Figure 6(a) shows the contours of for all porous cases and the solid case (Table 1) at the chosen threshold of 0.3. With this threshold, we are able to define the length and height of the wake, and , respectively (Figure 6a). is defined as the length of wake measured from the centreline of the patch () to the -maxima of the chosen contour level, while is the height of wake measured from the floor of the tunnel () to the -maxima of
Figure 6. Figure 6. Contours of time-averaged (a) defect velocity , (b) wall-normal velocity at , and (c) scalar concentration . Colour scheme for each case (C39, C64, C133, and CS) is described in Table 1. The horizontal and vertical extent of the wake are defined by and , respectively, while and are the horizontal and vertical extent of the scalar dispersion. Hatched regions illustrate the location of the patch.
the same contour level. Figure 7(a,Figure 7b) show the normalised length and height of the wake, and , respectively, as a function of solidity . The figures show that decreases with increasing , but increases (and possibly reaches a maxima at certain value of ) and then decreases as , where the obstacle is no longer porous and there is no flow escaping from the top of the patch. The wake ‘blow-up’ (i.e. taller wake) in higher has also been recorded in Taddei et al. [37]; Nicolai et al. [27]. These tendencies of and are insensitive to the change in threshold, as illustrated by the hatched regions in Figure 7(a,Figure 7b), which correspond to the same quantities measured when the threshold for is varied by . As a comparison, and measured in Nicolai et al. [27] are shown in white-filled circles in Figure 7(a,Figure 7b). The study involved similar arrays of cylindrical patches of various () that impinged a developing turbulent boundary layer at (20 times higher than that of the current study). It should be noted that the measured and are greater in magnitude as the wake is defined at a lower threshold of instead of 0.3 due to the increasing streamwise length of the FOV ( instead of ). It should also be noted that the values of (white-filled circles in Figure 7b) are scaled by a factor of , where 3.58 is the ratio of incoming boundary layer thickness to cylinder height in Nicolai et al. [27]. However, the differences between studies do not change the observed trend in and as a function of .
Figure 7. Figure 7. (a) Normalised length of wake (●) and scalar dispersion (♦) (as illustrated in Figure 6) of all test cases as a function of solidity , (b) height of wake (●) and scalar dispersion (♦), and (c) integrated velocity bleeding at the trailing edge . In (a,b), hatched regions illustrate the sensitivity to the threshold level defining the length/height (±20%). In (c), ○: same quantities measured in Nicolai et al. [27] at . (d) as a function of downstream of the patch, – –: the reference smooth-wall case TBL. (e) Integrated scalar concentration as a function of . Colour scheme for each case (C39, C64, C133, and CS) is described in Table 1.
Similarly, a threshold can also be applied to the scalar concentration field to measure the extent of scalar dispersion downstream of the patch. Figure 6(b) shows the contours of for all porous cases and the solid case (Table 1) at the chosen threshold of . The length and height of scalar dispersion and , respectively, are measured from the centreline of the patch to the -maxima of the chosen contour level and from the the floor of the tunnel to the -maxima, respectively. Filled diamonds in Figure 7(a,Figure 7b) show the measured and as a function of . Similar to those of the wake extent, and decreases and increases, respectively, with increasing . It should be noted that although scalar concentration data are available for case CS, the magnitude of downstream of the patch is lower than that of the chosen threshold (Figure 5d) and thus we are unable to measure and of this case.
We further quantify the velocity of TE bleeding . is defined as downstream of the patch () integrated over . This definition can be extended further to the scalar concentration at the trailing edge , such that
Figure 7(c) shows the magnitude of at the trailing edge, , as a function of . White-filled circles are measured by Nicolai et al. [27] for similar cylindrical arrangements at . Despite the difference in the order of , both Nicolai et al. [27] and the present study show that decreases with at the trailing edge. Figure 7(d) and Figure 7(e) further show the defect and as functions of downstream of the patch (). Both figures show the decay of wake and scalar concentration with , with (generally) faster decay as increases in the porous cases. In particular, in Figure 7(d) shows that the solid case CS recovers the fastest to the upstream condition (i.e., the incoming flow, dashed line is the smooth-wall case TBL), followed by the highest solidity case C133. We note that the decay of the wake for the porous and solid cases (Figure 7d) and the decay of for the porous cases (Figure 7e) seem to follow a certain power law, possibly similar to that of Wygnanski et al. (1986) for various solid and porous wake generators, which is left for future works. The exception to this is the scalar concentration downstream of case CS (black solid line in Figure 7e), which is approximately constant in and much lower in magnitude compared to the porous cases.
A closer look into Figure 7(e) reveals a curious observation: the integrated scalar concentration of case C64 peaks at , and the magnitude of this peak is much higher than that of cases with lower and higher (C39 and C133). Figure 8(a–Figure 8d) show the coloured contours of at the trailing edge for all porous and solid cases, with blue contour lines superimposed in the figures showing , which corresponds to flow recirculation. For case C64, figure 8(b) shows a high scalar concentration (purple-shaded region) at the trailing edge and up to , which is responsible for the spike in figure 7(e), immediately followed by the emergence of a recirculation bubble. In other words, the scalar is trapped between the porous patch upstream and the recirculation bubble that prevents the scalar from convecting downstream. By contrast, case C39 (figure 8a) that has lower solidity shows no recirculation bubble, and thus the scalar is freely transported downstream of the patch. Case C133 (figure 8c), on the other hand, shows the recirculation bubble being shifted to the trailing edge. The scalar in this case is largely prevented from escaping towards the trailing edge (this explains the decrease in and as solidity increases, see figure 7a). Conservation laws dictate two possible outlets left for the flow: lateral and vertical bleeding. The higher magnitude of above the patch, upstream of the bubble (, ) confirms increasing vertical bleeding in higher solidity, while the increase of lateral bleeding with has been confirmed in Zhou and Venayagamoorthy [45]. In some sense, the flow lingers downstream of the porous obstruction (characterised by high magnitude of in this region in case C64), it is as if the obstruction is extended in the streamwise direction. The length of this extension seems to be inversely proportional to , as it is longer than the FOV for case C39 (or perhaps infinitely long), approximately equal to for case C64 (figure 8b), and 0 for case C133 (figure 8c). Possibly, the extension length is akin to the length of the steady wake region observed in 2-D patches (Ball et al., [4]; Zong and Nepf, [46]; Chen et al., [9]). When the obstruction is impermeable (figure 8d), the mechanism differs. It acts as a solid body, shedding a pair of shear layers at the trailing edge (see contours of positive and negative and at in figures 4d and 5d, respectively).

Figure 8. Contours of scalar concentration for cases: (a) C39, (b) C64, (c) C133, and (d) CS. Blue solid lines (—) are negative streamwise velocity, in (b): and in (c,d): .
Vertical bleeding and the extent of scalar concentration
Contours of above the patches are shown in solid lines in figure 5. The contours reveal a very different pattern of flow above the patches for porous cases (figure 5a–c) compared to the solid case CS (figure 5d). In case CS, flow separation is characterised by high magnitude of observed in the leading edge of the patch (). Compared to the solid case, the magnitude of in the leading edge is lower for all porous cases (figure 5a–c), as the flow is able to penetrate the patches instead of being diverted upward (see Taddei et al., [37] for similar 3-D patches and Zhou and Venayagamoorthy, [45] for suspended patches, note that the sign of is inverted in the latter). What is only observed in the porous patches, however, is that the presence of region across the top surface of the patches ( and ) due to vertical bleeding. The magnitude and extent of this region appear to be dependent upon solidity. As a comparison, the contours of for the porous cases in figure 6(b) show that for the same magnitude (), is extended upward (in ) as increases.
Similar to the analysis in § 4.1, we quantify the magnitude of vertical bleeding as the integrated above the patch ( and ), and this can be further extended to include the scalar concentration,
Figures 9(a,b) show the integrated vertical bleeding and scalar concentration as functions of above the patch. Both figures show higher magnitude of and closer to the patch, which decay further towards the freestream. Dependency on is apparent on both. in Figure 9(a) generally increases with , with a significantly smaller magnitude (within of the incoming flow , see hatched region in Figure 9a) for CS and TBL (black solid and dashed lines in Figure 9a, respectively). For case CS, small is the result of averaging between high magnitude of in the leading edge and above the patch (see contour lines in Figure 5d), while for case TBL () this can be attributed to the error of the measurements. The integrated scalar concentration in Figure 9(b) is 0 for the solid case CS (since there is no vertical bleeding, see black solid line in Figure 9b), while for the porous cases it increases with and decays to 0 further from the patch.
Figure 9. (a) Integrated vertical bleeding above the patch () as a function of . - - -: the reference smooth-wall case TBL. Hatched region shows of . (b) Integrated scalar concentration above the patch . Colour scheme for each case (C39, C64, C133, and CS) is described in Table 1.
In addition to increasing vertical bleeding with , we also observed that the maxima of in Figure 9(b) occurs at the top surface of the patch for all porous cases, but the maxima of in Figure 9(a) occurs further from the patch (for example, it occurs at for case C133 in Figure 9a). Figures 10(a–c) offer a closer look of the flow above the porous patches. The coloured contours are the scalar concentration in logarithmic scale and the solid black lines are the contours of , representing the shear layer forming above the patches. In case C39 (Figure 10a) the shear layer shields a region of (relatively) high scalar concentration (orange-shaded contours in Figure 10a) below the layer. As solidity increases in case C64 (Figure 10b), higher is observed downstream of the patch (purple-shaded coloured contours), which coincides with elevation of the shear layer compared to that of C39 in Figure 10(a). In the case with the highest solidity (C133 in Figure 10c), recirculation occurs on the trailing edge (Figure 8c) followed by higher above the patch compared to that downstream of the patch (Figure 10c). Here the shear layer is elevated further upward, shielding the observed high above the patch (). Similar to the analogy of ‘artificial’ streamwise extension in the porous obstructions discussed in §3.1, here there seems to be an artificial upward extension of the obstruction as increases. This perhaps explains the phenomenon observed in Figure 9, that the maxima of vertical bleeding occurs further from the patches but the maxima of scalar concentration occurs exactly at the top surface of the patches.

Figure 10. Contours of scalar concentration for cases: (a) C39, (b) C64, (c) C133, and (d) CS. Black solid lines (—) are the normalised vorticity in axis .
Conclusions and Recommendations
We conduct planar PIV-PLIF measurements of the flow surrounding 3-D, circular porous patches of various solidity (0.098 1) to study the characteristics of flow in the wake of and above the patches. Porosity is generated by mounting rigid cylinders of height and diameter on the patch (whose diameter is ) and the variation in is achieved by systematically increasing the number of cylinders in a patch. The patches are fully submerged within the incoming flow, with a fluorescent dye injected from the floor of the tunnel, creating a point source upstream of the patches. Simultaneous PIV-PLIF measurements in – plane provide streamwise and wall-normal velocity components, as well as the concentration of the fluorescent tracer in the FOV.
Examination of the time-averaged velocity and scalar fields suggests that the trailing edge (longitudinal) and vertical flow bleeding from the obstructions decreases and increases with increasing , respectively, as previously reported in Taddei et al. [37]; Zhou and Venayagamoorthy [45]; Nicolai et al. [27]. In addition to that, we observe that affects the scalar concentration in the wake and above the patch. In particular, present results suggest that determines
the horizontal extent of the wake () and scalar concentration () downstream of the porous patches, with and decreasing with (Figure 7a). The decrease is attributed to the shift of recirculation bubbles towards the trailing edge of the patches as increases. High scalar concentration is observed downstream of the patch as the flow is trapped between patches and recirculation bubble, acting as an elongation of the obstructions in streamwise direction.
the vertical extent of the wake () and scalar concentration () downstream of the porous patches, with and increasing with (Figure 7b). As increases further, recirculation bubble occurs at the trailing edge of the patch and the flow is trapped in the interior of the patch. The flow largely escapes by means of vertical (and lateral) bleeding. High concentration of scalar, elevation of shear layer and above the patch suggest that the flow is trapped between the top surface of the patch, from which the flow bleeds, and the shear layer. Here we observe an artificial extension of the obstacle further upward (i.e. the patch is ‘taller’ from the perspective of the flow) as increases.
As a final remark, the mean scalar/flow fields understanding both momentum and scalar transport of the flow surrounding 3-D porous obstructions and building useful models for engineering design, prediction for meteorological or oceanographic flows, etc. The results presented in this study are limited to the time-averaged velocity and scalar components. However, we note that intermittency (i.e. discrepancies between the time-averaged and instantaneous flow fields) has been reported in Cassiani et al. [5] and Taddei et al. [37]. In the future, analysis about the fluctuating components (, , and ) should be included to obtain the full picture of the flow characteristics. The decay of wake and scalar concentration in the trailing edge, shown in Figure 7(d,Figure 7e), indicate a possible wake model for both porous and solid cases, which should also be investigated in the future.
Funding Statement. The authors gratefully acknowledge the financial support from EPSRC (Grant Nos: EP/P021476/1 and EP/S013296/1).
Declaration of Interests. The authors declare no conflict of interest.
Author Contributions. CN designed, performed all measurements, and post-processed the data. DDW post-processed, analysed the data, and wrote the manuscript, with the supervision from BG.
Data Availability Statement. The data that support the findings of this study will be made available upon publication.
Ethical Standards. The research meets all ethical guidelines, including adherence to the legal requirements of the study country.
Supplementary Material. Not available.
Cite this article: Wangsawijaya, D. D., Nicolai, C., & Ganapathisubramani, B. (2021). Time-averaged velocity and scalar fields of the flow surrounding a group of cylinders. Flow, E1. doi:xxx
References
- [1]R. Ahmadian, R. Falconer, and B. Bockelmann-Evans. Far-field modelling of the hydro-environmental impact of tidal stream turbines. Renew. Energy, 38(1):107–116, 2012. http://dx.doi.org/10.1016/j.renene.2011.07.005.
- [2]E. Aristodemou, L. M. Boganegra, L. Mottet, D. Pavlidis, A. Constantinou, C. Pain, A. Robins, and H. ApSimon. How tall buildings affect turbulent air flows and dispersion of pollution within a neighbourhood. Environ. Pollut., 233:782–796, 2018. http://dx.doi.org/10.1016/j.envpol.2017.10.041.
- [3]S. Baidya Roy, S. W. Pacala, and R. Walko. Can large wind farms affect local meteorology? J. Geophys. Res. Atmos., 109(D19), 2004. http://dx.doi.org/10.1029/2004JD004763.
- [4]D. Ball, P. Stansby, and N. Allison. Modelling shallow water flow around pile groups. Proc. Instn Civ. Engrs Wat., Marit. & Energy, 118(4):226–236, 1996.DOI
- [5]M. Cassiani, G. Katul, and J. Albertson. The effects of canopy leaf area index on airflow across forest edges: large-eddy simulation and analytical results. Bound.-Layer Meteorol., 126(3):433–460, 2008. http://dx.doi.org/10.1007/s10546-007-9242-1.
- [6]I. Castro. Wake characteristics of two-dimensional perforated plates normal to an air-stream. J. Fluid Mech., 46(3):599–609, 1971. http://dx.doi.org/10.1017/S0022112071000727.
- [7]K. Chang and G. Constantinescu. Numerical investigation of flow and turbulence structure through and around a circular array of rigid cylinders. J. Fluid Mech., 776:161–199, 2015. http://dx.doi.org/10.1017/jfm.2015.321.
- [8]W.-Y. Chang, G. Constantinescu, and W. F. Tsai. On the flow and coherent structures generated by a circular array of rigid emerged cylinders placed in an open channel with flat and deformed bed. J. of Fluid Mech., 831:1–40, 2017. http://dx.doi.org/10.1017/jfm.2017.558.
- [9]Z. Chen, A. Ortiz, L. Zong, and H. Nepf. The wake structure behind a porous obstruction and its implications for deposition near a finite patch of emergent vegetation. Water Resour. Res., 48(9), 2012. http://dx.doi.org/10.1029/2012WR012224.
- [10]Z. Chen, C. Jiang, and H. Nepf. Flow adjustment at the leading edge of a submerged aquatic canopy. Water Resour. Res., 49(9):5537–5551, 2013. http://dx.doi.org/10.1002/wrcr.20403.
- [12]J. Finnigan. Turbulence in plant canopies. Annu. Rev. Fluid Mech., 32(1):519–571, 2000. http://dx.doi.org/10.1146/annurev.fluid.32.1.519.
- [13]J. Huang, M. Cassiani, and J. Albertson. Analysis of coherent structures within the atmospheric boundary layer. Bound.-Layer Meteorol., 131(2):147–171, 2009a. http://dx.doi.org/10.1007/s10546-009-9357-7.
- [15]J. Huang, M. Cassiani, and J. Albertson. Coherent turbulent structures across a vegetation discontinuity. Bound.-Layer Meteorol., 140(1):1–22, 2011. http://dx.doi.org/10.1007/s10546-011-9600-x.
- [16]M. Kanda. Large-eddy simulations on the effects of surface geometry of building arrays on turbulent organized structures. Bound.-Layer Meteorol., 118(1):151–168, 2006. http://dx.doi.org/10.1007/s10546-005-5294-2.
- [17]G. Katul, G. Kuhn, J. Schieldge, and C.-I. Hsieh. The ejection-sweep character of scalar fluxes in the unstable surface layer. Bound.-Layer Meteorol., 83(1):1–26, 1997. http://dx.doi.org/10.1023/A:1000293516830.
- [18]J. L. Kemp, D. M. Harper, and G. A. Crosa. The habitat-scale ecohydraulics of rivers. Ecol. Eng., 16(1):17–29, 2000. http://dx.doi.org/10.1016/S0925-8574(00)00073-2.
- [19]J. Lee, Kevin, J. Monty, and N. Hutchins. Validating under-resolved turbulence intensities for PIV experiments in canonical wall-bounded turbulence. Exp. Fluids, 57:129, 2016. http://dx.doi.org/10.1007/s00348-016-2209-6.
- [20]J. Lei and H. Nepf. Evolution of flow velocity from the leading edge of 2-D and 3-D submerged canopies. J. Fluid Mech., 916, 2021. http://dx.doi.org/10.1017/jfm.2021.197.
- [21]D. Li and E. Bou-Zeid. Coherent structures and the dissimilarity of turbulent transport of momentum and scalars in the unstable atmospheric surface layer. Bound.-Layer Meteorol., 140(2):243–262, 2011. http://dx.doi.org/10.1007/s10546-011-9613-5.
- [22]L. Myers and A. Bahaj. An experimental investigation simulating flow effects in first generation marine current energy converter arrays. Renew. Energy, 37(1):28–36, 2012. http://dx.doi.org/10.1016/j.renene.2011.03.043.
- [23]H. Nepf, C. Mugnier, and R. Zavistoski. The effects of vegetation on longitudinal dispersion. Estuar. Coast. Shelf Sci., 44(6):675–684, 1997. http://dx.doi.org/10.1006/ecss.1996.0169.
- [24]H. M. Nepf. Drag, turbulence, and diffusion in flow through emergent vegetation. Water Resour. Res., 35(2):479–489, 1999. http://dx.doi.org/10.1029/1998WR900069.
- [27]C. Nicolai, S. Taddei, C. Manes, and B. Ganapathisubramani. Wakes of wall-bounded turbulent flows past patches of circular cylinders. J. Fluid Mech., 892, 2020. http://dx.doi.org/10.1017/jfm.2020.102.
- [28]A. Nicolle and I. Eames. Numerical study of flow through and around a circular array of cylinders. J. Fluid Mech., 679:1–31, 2011. http://dx.doi.org/10.1017/jfm.2011.77.
- [29]D. R. Plew. Depth-averaged drag coefficient for modeling flow through suspended canopies. J. Hydraul. Eng., 137(2):234–247, 2011. http://dx.doi.org/10.1061/ASCЕHY.1943-7900.0000300.
- [30]D. Poggi, A. Porporato, L. Ridolfi, J. Albertson, and G. Katul. The effect of vegetation density on canopy sub-layer turbulence. Bound.-Layer Meteorol., 111(3):565–587, 2004. http://dx.doi.org/10.1023/B:BOUN.0000016575.0621.73.
- [31]D. Poggi, G. Katul, and J. Albertson. Scalar dispersion within a model canopy: Measurements and three-dimensional lagrangian models. Adv. Water Resour., 29(2):326–335, 2006. http://dx.doi.org/10.1016/j.advwatres.2004.12.017.
- [32]D. A. Rajewski, E. S. Takle, J. H. Prueger, and R. K. Doorenbos. Toward understanding the physical link between turbines and microclimate impacts from in situ measurements in a large wind farm. J. Geophys. Res. Atmos., 121(22):13–392, 2016. http://dx.doi.org/10.1002/2016JD025297.
- [33]M. Raupach and A. Thom. Turbulence in and above plant canopies. Annu. Rev. Fluid Mech., 13(1):97–129, 1981. http://dx.doi.org/10.1146/annurev.fl.13.010181.000525.
- [34]J. T. Rominger and H. M. Nepf. Flow adjustment and interior flow associated with a rectangular porous obstruction. J. Fluid Mech., 680:636–659, 2011. https://doi.org/10.1017/jfm.2011.199.
- [35]H. Schlichting and K. Gersten. Boundary-Layer Theory. Springer-Verlag Berlin, Heidelberg, 9th edition, 2017. http://dx.doi.org/10.1007/978-3-662-52919-5.
- [36]J. Sillero, J. Jiménez, and R. Moser. Two-point statistics for turbulent boundary layers and channels at Reynolds numbers up to δ+ ≈ 2000. Phys. Fluid, 26:105109, 2014. http://dx.doi.org/10.1063/1.4899259.
- [37]S. Taddei, C. Manes, and B. Ganapathisubramani. Characterisation of drag and wake properties of canopy patches immersed in turbulent boundary layers. J. Fluid Mech., 798:27–49, 2016. http://dx.doi.org/10.1017/jfm.2016.312.
- [38]Y. Tanino and H. M. Nepf. Lateral dispersion in random cylinder arrays at high reynolds number. J. Fluid Mech., 600:339–371, 2008. http://dx.doi.org/10.1017/S0022112008000505.
- [39]R. O. Tinoco and G. Coco. A laboratory study on sediment resuspension within arrays of rigid cylinders. Adv. Water Resour., 92:1–9, 2016. http://dx.doi.org/10.1016/j.advwatres.2016.04.003.
- [40]H. L. Tseung, G. A. Kikkert, and D. Plew. Hydrodynamics of suspended canopies with limited length and width. Environ. Fluid Mech., 16(1):145–166, 2016. http://dx.doi.org/10.1007/s10652-015-9419-y.
- [41]C. Vanderwel and S. Tavoularis. On the accuracy of PLIF measurements in slender plumes. Exp. Fluids, 55(8):1–16, 2014. http://dx.doi.org/10.1007/s00348-014-1801-x.
- [42]R. Vennell. Tuning tidal turbines in-concert to maximise farm efficiency. J. Fluid Mech., 671:587–604, 2011. http://dx.doi.org/10.1017/S0022112011000619.
- [43]B. L. White and H. M. Nepf. Scalar transport in random cylinder arrays at moderate reynolds number. J. Fluid Mech., 487:43–79, 2003. http://dx.doi.org/10.1017/S0022112003004579.
- [45]J. Zhou and S. K. Venayagamoorthy. Near-field mean flow dynamics of a cylindrical canopy patch suspended in deep water. J. Fluid Mech., 858:634–655, 2019. http://dx.doi.org/10.1017/jfm.2018.775.
- [46]L. Zong and H. Nepf. Vortex development behind a finite porous obstruction in a channel. J. Fluid Mech., 691:368–391, 2012. http://dx.doi.org/10.1017/jfm.2011.479.




