betaFeedback

WorksPhysics and Astronomy

Multi-Functional Metasurfaces with M-Type Ferrites: Shaping the Future of mmWave Absorption and Beam Steering

Abstract

This paper presents a comprehensive review and tutorial on multi-functional metasurfaces integrated with M-type ferrite materials for millimeter-wave (mmWave) absorption and beam control. As wireless communication systems transition toward beyond-5G architectures, including non-terrestrial networks (NTNs), the demand for adaptive, low-profile electromagnetic surfaces that can manage interference while enabling beam reconfiguration becomes increasingly critical. Conventional metasurfaces often struggle to simultaneously achieve high absorption and beamforming over wide frequency ranges due to intrinsic material and structural limitations. This paper reviews the state-of-the-art in metasurface design for dual-functionality, particularly those combining frequency-selective magnetic materials with periodic surface lattices, to enable passive, compact, and reconfigurable reflectors and absorbers. Special emphasis is placed on the role of M-type ferrites in enhancing absorption via ferromagnetic resonance, and on the use of surface-wave trapping mechanisms to achieve narrowband and broadband functionality. A case study of a ferrite-based hybrid "reflectsorber" (reflectorarray + absorber) is presented to demonstrate key design concepts, analytical models, and application scenarios relevant to satellite, UAV, and NTN ground station deployments. Future directions for low-loss, tunable, and scalable metasurfaces in next-generation wireless infrastructures are also discussed.

Introduction

The expansion of non-terrestrial networks (NTNs) including high-altitude platform systems (HAPS) and low earth orbit (LEO) satellite constellations is drastically increasing the density of transmitters and receivers in the wireless ecosystem, as shown in Figure 1 [1, 2, 3, 4, 5, 6, 7]. While these emerging platforms promise global coverage and low-latency links, they often share spectrum with legacy systems, leading to escalating interference challenges. For example, LEO mega-constellations plan to operate in Ku/Ka/V bands that overlap with existing

Non-terrestrial network architecture involving LEO satellites and HAPS

Figure 1. Non-terrestrial network architecture involving LEO satellites and HAPS.

geostationary (GEO) satellite and terrestrial cellular allocations, resulting in severe co-channel interference if unmitigated [1, 2, 3]. Likewise, HAPS platforms, which provide connectivity from the stratosphere, intend to use licensed sub-6 GHz mobile bands for a scenario that demands careful coordination with ground networks to prevent cross-tier interference [5, 6, 7]. In general, modern hybrid networks frequently operate on closely adjacent frequency spectra, and conventional broadband approaches struggle with such coexistence issues. These trends make interference mitigation a critical concern in beyond-5G communications.

One promising approach to address these challenges is the use of metasurface-assisted communications. Reconfigurable intelligent surfaces (RIS), or programmable metasurfaces, enable dynamic control of electromagnetic wave propagation, surpassing the capabilities of traditional antennas and fixed filters [8]. Essentially, an RIS is a two-dimensional metamaterial array with tunable elements, enabling software-defined control over the phase, amplitude, polarization, and even frequency response of impinging signals. By deploying RIS panels on building facades, indoor walls, or aerial platforms, the wireless channel itself becomes controllable. This capability allows the network to direct and focus coverage or nullify undesired paths, thereby improving signal quality and reducing interference. In fact, intelligent metasurfaces have been proposed to actively manipulate the propagation environment to mitigate interference from nearby cells or other unwanted transmitters. Compared to static filtering or coordination alone, metasurface-assisted beamforming can boost desired link gains while simultaneously deflecting or attenuating signals that would otherwise cause inter-system interference. This makes RIS technology a natural complement in hybrid NTN deployments, offering adaptive beam steering and spatial isolation without the need for power-hungry active relays. However, active metasurfaces generally require an additional microcontrollers and power supplies to control their operating states, which will incur significant size, weight, and power. Passive multi-functional metasurfaces can be alternatives in developing a low-cost, compact, and power-independent ground station for NTNs with pre-defined orbits or locations. Two prime examples of these multi-functionalities, and the focus of this work, are multi-band polarization converting and multi-channel spin-decoupled metasurfaces [9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20]. The multi-functionality, such as a dual-band operation, is necessary for the metasurface to handle separate frequency bands of uplink and downlink, ensuring reliable communication between ground stations and LEO satellites. Also, the metasurface with the multi-channel response can be utilized for a demanding task improving throughputs, such as adaptively splitting EM signals from ground stations to moving LEO satellites. Numerous studies have highlighted the substantial benefits of metasurfaces [21, 22, 23].

Beyond simply reflecting or transmitting signals toward intended receivers, next-generation multi-functional metasurfaces are evolving into interference-free platforms to cope with complex interference scenarios. In particular, there is a strong rationale to integrate absorptive and beam-steering functionalities into a single metasurface architecture. Traditional reflecting surfaces lack any mechanism to damp unwanted transmissions; however, by introducing an absorption mechanism in selected elements or frequency bands, a metasurface can actively dissipate interfering energy before it propagates further. Researchers have begun to demonstrate such dual-purpose designs – for instance, metasurface arrays that can switch between a reflective beamforming mode and a transmitting mode to effectively “wall off” certain signals [24]. The ability to selectively absorb stray or cross-polarized signals for undesired frequencies is especially valuable in dense NTN environments, where overlapping coverage areas and multipath can generate strong interference. By uniting absorption with rerouting (reflection/refraction) within different frequency bands, a single metasurface can thus serve as both a smart reflector for wanted beams and a spatial filter for unwanted ones.

This paper introduces, for the first time, a novel structure that combines a metasurface with an M-type ferrite slab, designed for advanced communication system with NTNs. In a higher-frequency region, high-quality factor resonances generated in periodic structures are analyzed by using the Floquet expansion method based on the dielectric substrate with the surface lattice. While the resonance frequencies of the periodic structure can be tailored through dimensional control, the inherently high-Q factor must be suppressed to enable broadband functionalities such as filtering or absorption. Conventional dielectric substrates pose limitations in increasing dielectric losses, which constrains their applicability in broadband designs. To address this, an M-type ferrite material is employed to effectively dissipate the trapped electromagnetic energy in the periodic structure. This magnetic material offers frequency-dispersive properties, allowing independent control of spectral behavior across different frequency bands. The proposed design can be applied in integrating the absorptive property and any beam-shaping function. This paper presents a concept and operational theory of the ‘reflectsorber’–a hybrid device that functions both as a reflectarray and an absorber for practical implementations. The validity of the theoretical model of the reflectsorber is demonstrated through the design and fabrication of the metasurface, which operates as a reflectarray at 38 GHz and an absorber at 77 GHz.

Multi-functional Metasurfaces: Review

Metasurfaces are ultrathin, engineered 2D materials composed of sub-wavelength elements that can manipulate electromagnetic waves in extraordinary ways, far beyond the limits of natural materials. By judicious design of these planar meta-atoms, one can finely tailor the phase, amplitude, and polarization of reflected or transmitted waves. In the microwave and millimeter-wave (mmWave) bands, such metasurfaces have enabled novel flat optics and antennas – including anomalous reflection/refraction [25, 26, 27, 28], invisibility [29, 30, 31], and vortex beam generation [32, 33, 34] – all in a compact form factor. This powerful wavefront control comes with significant benefits in high-frequency communication systems where size, weight, and power (SWaP) are at a premium. Meanwhile, the metasurfaces with a single function need to be developed for satisfying next-generation communication networks.

The motivation for multi-functional metasurfaces arises when a single engineered surface is designed to perform several electromagnetic functions at once, further reducing component count, size, and power consumption. For example, a single metasurface panel might simultaneously act as a high-gain antenna and a radar cross section (RCS) reductor, obviating the need for separate antenna feeds and RCS surfaces [35]. In satellite systems, this means one compact aperture can handle dual-polarized or circularly polarized links without the weight of mechanical polarizers, while in terrestrial 5G systems a metasurface can combine beamforming with interference suppression in one device. Such integration yields clear SWaP benefits: fewer physical parts, lighter payloads, and no lossy adapters, all translating to improved efficiency. In addition, multi-function metasurfaces can improve performance and flexibility, offering capabilities like dynamic polarization multiplexing or adaptive absorption that legacy hardware antennas cannot readily achieve.

Related WorkMaterialBeam-shaping FunctionInterference Mitigation
[11]F4B (Dielectric material)O (Dual-LP channel reflectarray)X
[10]Taconic TRF-43 (Dielectric material)O (Dual-CP channel reflectarray)X
[15]FR4 (Dielectric material)O (Dual-band dual-channel reflectarray)X
[16]FR4 (Dielectric material)O (Multi-band polarization conversion)X
[36]F4B (Dielectric material)XO (Ultra-wideband RCS reduction)
This workM-type ferrite (Frequency selective material)O (Reflectarray or Anomalous reflection)O (Absorption)

Table 1. Operation Comparison for Multi-functional Metasurfaces

Two prime examples of these multi-functionalities, and the focus of this work, are multi-band polarization converting and multi-channel spin-decoupled metasurfaces [9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20]. Metasurfaces can serve as efficient polarization converters, transforming an incident wave’s polarization state (for instance, from linear to circular polarization) over broad bandwidths, as shown in Figure 2. This is extremely valuable in satellite communications, where links often require circular polarization to mitigate Faraday rotation and polarization misalignment. A metasurface polarization converter can replace bulky quarter-wave plates or orthomode transducers, achieving the desired polarization in a thin planar layer. Likewise, metasurfaces enable dual-polarized reflectarrays in which a single aperture independently controls two orthogonal polarizations, as shown in Figure 2. Multi-channel metasurfaces, such as a dual-feed or dual-polarized metasurface, can generate two separate beams or communication channels on the same physical antenna, increasing the data throughput via polarization multiplexing. Compared to conventional single-polarized antennas, these metasurface-based solutions offer greater functionality without additional hardware, which is a decisive advantage in both satellite payloads and 5G base stations. In the following, we survey recent developments in these areas from polarization-converting metasurfaces to multi-channel metasurface designs, and also discuss a third emerging function: absorptive metasurfaces for interference management in hybrid terrestrial-satellite networks.

Multi-functional metasurface involved in the next-generation communication with non-terrestrial networks

Figure 2. Multi-functional metasurface involved in the next-generation communication with non-terrestrial networks, improving overall communication performances

Multi-channel Metasurfaces With Spin-decoupled Elements

One important class of multi-functional metasurface technology is the development of dual-polarized (or dual-feed) reflector whose elements can independently control orthogonal polarizations [9, 10, 11, 12, 13, 14, 15]. In a traditional reflectarray or phased array, managing two polarizations often requires duplicating hardware (e.g. separate arrays or interleaved elements for horizontal and vertical polarization) or using multi-layer structures with polarization-selective surfaces. The multi-functional metasurfaces offer a smarter solution: by designing each meta-element with anisotropic or multi-resonant features, one can impart a distinct phase shift to each polarization of the incident wave. In effect, the reflective surface can impose two independent phase profiles – one for, say, the xx-polarized component and one for the yy-polarized component – enabling full decoupled control of dual polarizations from the same aperture. This capability underpins a new class of dual-feed reflectarrays where two feed sources (often orthogonally polarized) illuminate the same metasurface, and the metasurface generates two different beams, one per polarization. The feeds could be, for example, a dual-polarized horn or two separate antennas, launching horizontal and vertical polarizations that are handled separately by the metasurface. Because the metasurface elements introduce low cross-coupling, each polarization can be beamformed or redirected independently, realizing beam multiplexing and polarization diversity with a single flat panel.

The benefits of such dual-polarized metasurface reflectarrays are substantial. First, they effectively double the communication capacity without doubling aperture size – two data streams can be sent/received on the same frequency band via orthogonal polarizations (polarization multiplexing). This is particularly advantageous for satellite communications and wireless backhaul links, where spectrum is precious and dual-polarization can roughly double the throughput. Indeed, a dual circularly polarized (dual-CP) reflectarray can transmit left-handed circularly polarized (LHCP) and right-handed circularly polarized (RHCP) beams on separate channels, greatly improving data rate and reducing polarization losses in a satellite link. Zhang et al. recently reported a Ku-band dual-CP reflectarray that radiates two independent beams for LHCP and RHCP at different angles (±20∘\pm20^\circ from broadside) with high gain 29 dB for each beam. Each unit cell in their design provides two phase responses such that the metasurface focuses the left-handed circularly polarized wave in one direction and the right-handed wave in another. Notably, they achieved this multiplexing in a single-layer metasurface by combining the dynamic phase (tuning element size to delay one polarization) and Berry phase (rotating elements to redirect the other polarization) within each cell. This approach circumvented the need for stacked polarizing layers and achieved broad 37% bandwidth for both CP channels. The result is an ultrathin dual-CP antenna that provides two high-gain beams from one aperture, exemplifying the beam-multiplexing power of spin-decoupled metasurfaces.

A reflective coding metasurface reported in [10] can independently tune the phase functions for CP wavefronts with two orthogonal helicities. The meta-atom in the metasurface has a low cross talk for linearly orthogonal polarized waves, which helps to introduce multi-OAM modes. It shows that a incident CP wave is able to be split into two different OAM beams at a microwave region of 16 GHz. Another multi-channel metasurface provides quadruplex channels for reflection and transmission modes, which is based on the meta-atom with linear polarized patches and phase delay lines [12]. Under LHCP incident wave, the metasurface can re-radiate the impinging wave into the four channels with transmitting space of RHCP/LHCP channels and reflecting space of RHCP/LHCP channel, covering 28–30 GHz. Besides, the multimaterial inside the multi-channel metasurface was fabricated by utilizing the 3-D printing technique.

Multi-band Metasurfaces for Polarization Transformations

Another frontier of multi-functional metasurfaces enables polarization conversion, wherein an incoming wave of one polarization is re-emitted in another polarization state [16, 17, 18, 19, 20]. This functionality is critical in wireless systems that must accommodate different polarization schemes for compatibility or performance reasons. For example, satellite transponders often use CP to avoid polarization alignment issues and to support dual orthogonal channels (RHCP/LHCP), even though ground terminals or feeder links may transmit in linear polarization (LP). A metasurface polarization converter can bridge this gap by converting linear-to-circular polarization over the satellite downlink/uplink bands. Similarly, in terrestrial links and radar, converting one linear polarization to its orthogonal counterpart (linear-to-linear, or LP–LP conversion) can improve link reliability and reduce interference by aligning with the receiver’s preferred polarization or by exploiting polarization diversity. Metasurface-based converters achieve this without bulky microwave components, using sub-wavelength resonators to impart the required phase shifts to the incident waves.

As reported in [16], the research proposes a multifunctional metasurface designed for efficient polarization manipulation, capable of both cross- and circular-polarization conversion. Specifically, it provides linear-to-linear polarization conversion over the frequency bands of 5.3–5.4 GHz, 7.2–8 GHz, and 12.3–13.76 GHz, while effectively converting linear polarization to circular polarization across broader ranges of 5.1–5.2 GHz, 5.6–6.85 GHz, 8.8–11.2 GHz, and 14.9–20.2 GHz. Due to its compact size, excellent angular stability up to 75°, and multifunctional capability, the metasurface is highly promising for diverse applications within strategic C-, X-, Ku-, and K-band communications. In [17], the other proposed metasurface

with an active tunability shows the multi-functional polarization conversion with ultrabroad bandwidth and large angular tolerance. Especially, the microfluidic network was involved in every galinstan-based metasurface element and controled their orthogonal resonant modes continuously. As proof of concept, the multifunctional polarization converter was validated for linear-to-linear, linear-to-circular, and linear-to-elliptical polarization conversions by controlling the galinstan within the microfluidic channels. The possibility of tuning the incident EM wave to any desired polarization state was suggested, showing intriguing new opportunity to create active devices with dynamic polarization control.

Interference Management via Absorptive Metasurfaces in Hybrid Networks

As communication networks become increasingly heterogeneous – integrating terrestrial 5G/6G cells with non-terrestrial nodes like satellites and high-altitude platforms – interference management emerges as a crucial challenge [37, 38, 39]. These hybrid networks involve a mix of signals at various frequencies and propagation directions, raising the risk of unwanted interactions: for instance, a satellite downlink might interfere with terrestrial base station receivers, or reflections off buildings might desensitize a nearby radar. Multi-functional metasurfaces can play a transformative role here by incorporating absorptive or scattering-reducing features to mitigate interference signals while still performing their primary communication functions. In essence, an absorptive metasurface can act as a selective shield – allowing or directing desired signals while simultaneously suppressing or diffusing stray and potentially interfering signals.

One application of absorptive metasurfaces is in controlling the radar cross-section (RCS) or general reflectivity of communication components [36, 40, 41, 42, 43, 44, 45]. A conventional antenna or reflecting surface can produce strong incidental reflections (e.g., backscatter towards a radar or echoes into other communication channels) that contribute to electromagnetic interference. By engineering a metasurface to be bifunctional – that is, to both steer the main beam and absorb energy outside the main beam or band – one can substantially reduce these undesired reflections. For example, an absorptive metasurface of [36] designed an absorptive coding metasurface for ultra-wideband RCS reduction that uses a resistive layer to absorb much of the incident energy while employing a 1-bit phase coding on the reflected portion to scatter the rest in diverse directions. Their metasurface’s unit cell was an anisotropic resistive patch that acted as a lossy polarization converter – co-polarized reflections were kept below −10 dB from 1.5 to 40 GHz, with the remaining cross-polarized reflections randomized in phase to cancel out coherently. The practical implication is that a communication panel based on such a metasurface would be far less visible to detection and would scatter negligible energy into other systems’ spectrum, thereby minimizing interference in a dense electromagnetic environment.

In the context of hybrid terrestrial/non-terrestrial networks, absorptive metasurfaces can be strategically deployed to isolate the two layers of the network. Consider a building-mounted intelligent reflecting surface that assists mmWave 5G signals: if that surface is also exposed to satellite downlink signals (e.g., in Ka-band or Q-band), a portion of the satellite signal might otherwise reflect and interfere with ground users or create multi-path issues. By designing the metasurface with frequency-selective absorption, it can absorb the satellite band signals (or any other unwanted band) while still efficiently reflecting the 5G band signals towards their target [44]. This frequency-selective absorption can be achieved by incorporating resistive elements tuned to the interfering band, converting those unwanted waves into heat. Essentially, the metasurface becomes a spatial filter, providing gain where needed and loss where beneficial. The result is improved electromagnetic compatibility between coexisting systems without adding a complex techniques. Similarly, absorptive metasurfaces can be used on satellite surfaces or ground station radomes to reduce outgoing sidelobe energy and echoes that might interfere with other satellites or radio services [45]. Because metasurface absorbers are thin and can cover large areas, they lend themselves to coating structures like aircraft, high-altitude platforms, or base-station towers to suppress scattering and interference.

It should be noted that purely absorbing metasurfaces inherently dissipate power, which in a communication context means some signal loss. Thus, designers often seek a balance: absorptive metasurfaces in communications are typically engineered to absorb only unwanted energy (out-of-band signals, high-angle sidelobes, reflections back toward interferers) while preserving high efficiency for the desired in-band, in-beam signals. It is challenging to realize an integrating metasurface with absorbing and beam-shaping properties, without a performance degradation in both absorbing and radiating properties. A new design methodology is required, to realize the bi-functional metasurface within a single slab. In this work, a novel metasurface architecture is proposed by integrating a frequency-selective material with a periodic structure, enabling multi-functionality. The proposed metasurface simultaneously supports both absorption and beam-steering functionalities, ensuring interference-free communications for undesired frequency band, as Case 3 in Figure 3. Furthermore, additional features, such as polarization conversion and multi-channel operation, can be seamlessly incorporated into the design while maintaining its absorptive characteristics as shown in Table I.

Schematic of the proposed metasurface with the application sketch

Figure 3. Schematic of the proposed metasurface with the application sketch. The inset of the schematic shows the different operation of the unit-cell of the metasurface based on M-type ferrite and conventional dielectric materials.

Analysis of Surface Waves in Metasurfaces

Floquet Harmonic Surface Waves on Dielectric Substrates

It is considered that the metasurface composed of zero-thickness metallic patches lies on either a dielectric or ferrite substrate. As shown in Figure 4(a), a TE-polarized plane wave is incident at an angle θ\theta in the principal yzyz plane of the patch array The impinging field parallel to the periodic structure is in the EE-plane, inducing the surface currents on the metasurface. Reflection and transmission from the metasurface with periodic structure correspond to the interference of an infinite set of propagating and evanescent plane waves, i.e., Floquet harmonics. As shown in Figure 4(b), the propagation of the incident and reflected plane waves can be modeled by the equivalent circuit network (ECN) by waveguide and the impedance matching concepts (see Appendix) [46, 47]. When the plane wave arrives at the metasurface with periodic structure, the scattered harmonics can be excited along the surface lattice. The wave numbers (kx,m(k_{x,m} and ky,n)k_{y,n}) in the xx- and yy-axes associated with the Floquet harmonics of order mm and nn are denoted by

Configuration of the metasurface based on the M-type ferrite with the transverse electric plane wave

Figure 4. The configuration of the metasurface based on the M-type ferrite with the transverse electric (TE) plane wave. (a) Scheme of the patch array of finite thickness under oblique incidence, (b) equivalent circuit network corresponding to the proposed structure, and (c) equivalent circuit network in case of the transverse resonance of any hh-th harmonic.

kx,m=2mπP(1)k_{x,m} = \frac{2m\pi}{P} \tag*{(1)}
ky,n=k0sin⁡θ+2nπP(2)k_{y,n} = k_0 \sin\theta+ \frac{2n\pi}{P} \tag*{(2)}

where mm and nn are integer numbers (m,n=0,±1,±2,⋯ )(m,n = 0, \pm1, \pm2, \cdots), and k0k_0 is the free-space wavenumber. Inside a substrate, the normal wave-number of hh-th harmonic with a mode pair of mnmn are defined as follows:

kz,h(a)={βh(a)={k(a)}2−∣kt,h∣2,k(a)≥∣kt,h∣−jαh(a)=−j∣kt,h∣2−{k(a)}2,k(a)<∣kt,h∣(3)k_{z,h}^{(a)} = \begin{cases} \beta_h^{(a)} = \sqrt{\{k^{(a)}\}^2 - \lvert\mathbf{k}_{t,h}\rvert^2}, & k^{(a)} \ge\lvert\mathbf{k}_{t,h}\rvert\\ -j\alpha_h^{(a)} = -j\sqrt{\lvert\mathbf{k}_{t,h}\rvert^2 - \{k^{(a)}\}^2}, & k^{(a)} < \lvert\mathbf{k}_{t,h}\rvert \end{cases} \tag*{(3)}

where the type of substrate is indicated by the superscript (a)(a). The superscripts (d) and (m) for (a)(a) indicate the dielectric

substrate with μr=1\mu_r = 1 and the magnetic substrate with μr≠1\mu_r \ne1, respectively. If the superscript is (0), the substrate is considered to be the free space with ϵr=1\epsilon_r = 1 and μr=1\mu_r = 1. For a lossless material, the wave numbers are represented as purely real or purely imaginary wavenumbers, which indicates whether it is a propagating or evanescent wave.

As shown in Figure 5(a), the normal component of the propagating modes impinging the substrate appears at a certain wavelength with respect to an angle of θ\theta and a periodic of PP. The regions corresponding to each propagation property exactly depend on the periodicity: (i) evanescent, (ii) guided, and (iii) trapped modes [48, 49]. Figure 5(b) shows the surface wave of the hh-th harmonic is exponentially decayed within frequencies of Region i. In Region ii, the surface wave of the hh-th harmonic starts to impinge the substrate, while guided between the metasurface and the ground plane. The surface wave of the hh-th harmonic flows along the metasurface when satisfying the transverse resonance condition that Y1(0)+Yin,1(a)=0Y_1^{(0)} + Y_{\mathrm{in},1}^{(a)} = 0. The transverse resonances corresponding to TM01, TM11, and TE10 nides are denoted as ftr1f_{\mathrm{tr1}}, ftr2f_{\mathrm{tr2}}, and ftr3f_{\mathrm{tr3}}, respectively. As shown in Figure 4(c), the dielectric substrate are only considered without the influence of the hh-th harmonics because the input impedance (ZeqZ_{\mathrm{eq}}) is infinite at the transverse resonance. After transverse resonance of the hh-th harmonic, the guided waves of the hh-th harmonics with a slower wavenumber are trapped within the surface lattice for Region iii. For all the trapped waves of the hh-th harmonic, interesting resonances with high-quality factor are generated by facing the incident wave.

Figure 5. (a) Real part of the normal wavenumber for the hh-th harmonics with the fixed periodicity and (b) the description of the propagating properties for the operating regions.

As illustrated in Figure 6, the interesting influence of space harmonic resonance is examined by comparing the cases of periodicities P=2P = 2 mm and P=3P = 3 mm, where the metasurface with a=1a = 1 mm is positioned on a dielectric substrate with a relative permittivity of ϵr=6.5\epsilon_r = 6.5. The substrate thickness is optimally set to a quarter wavelength (λ/4\lambda/4) in order to exploit the phase cancellation between the incident wave and the trapped wave of the hh-th harmonic. In the common case with a unit-cell spacing, the fundamental resonance of the metasurface with periodic structure can be easily expected as fr≈2c/(aϵr)f_r \approx2c/(a\sqrt{\epsilon_r}). While the peak 1 is derived from the fundamental mode, an additional resonance modes emerge when the periodicity increases with a fixed size of aa. As shown in Figure 5, the extra trapped surface waves resonated within the periodic metasurface can be introduced for increasing the unit-cell spacing (PP). The quality factors of the new resonances have higher values of more than 100, which provides a potential of absorbing and filtering applications with high performance.

Full-wave electromagnetic simulation for reflection coefficient of a metasurface

Figure 6. Full-wave electromagnetic simulation for reflection coefficient of a metasurface with P=2P = 2 and P=3P = 3 mm

To further specify the trapped surface wave of these additional resonances, the analytic approach of ECN modeling is applied on this metasurface. The influence of hh-th space harmonic caused in a periodic structure can be simplified into a transmission line based on waveguide concept of ECN model. For a fixed size of a=1a = 1 mm and a varying spacing of PP, the finite element method (FEM) simulation and the numerical calculation based on ECN modeling are conducted, while representing the excellent agreement as shown in Figure 7(a) and (b). It is notable that the resonance frequencies are determined by the periodicity variation. Also, the comparison confirms that the periodic structure resonances are derived from the impedance matching between the incident wave and the trapped wave of the hh-th harmonic. As shown in Figure 8, the peak 2 and 3 generated by the periodic structure resonance follow behind the transverse resonance. The unit-cell spacing (PP) can be managed for the frequencies of the peaks to be

Reflection coefficient of the metasurface calculated using equivalent circuit network

Figure 7. Reflection coefficient of the metasurface with periodic structure as a function of the unit-cell spacing calculated by (a) 3D FEM simulation and (b) ECN model approach

Variation of peak points and transverse resonances

Figure 8. Variation of peak points and transverse resonances in the reflection coefficient regarding to the unit-cell spacing (PP).

in an interesting region for obtaining the desired filtering or absorbing property.

Figure 9 represents distributions of the zz-direction E-field (EzE_z) at the ground plane for a selected few frequencies. As shown in Figure 9(a) and (b), the EzE_z-fields at 48 and 60 GHz demonstrate the fundamental resonances of the metasurface with periodic structure and its sustained resonance beyond the resonant frequency. In these cases, the EzE_z-fields are most intense on the border of the square pattern. As shown in Figure 9(c) and (d), a considerable amount of EzE_z-field is bound within the periodic structure far from the square pattern at 70 and 85 GHz. The discrepancy of the EzE_z-field distributions at 70 and 85 GHz is caued by the different propagating modes of the surface waves. These distributions prove the resonances of the higher frequencies are generated by the trapped waves propagating parallel to the plane of the surface. However, the remaining EzE_z-field distribution adjacent to the patch means the absorption mechanism does not work with the conventional dielectric material.

Simulated $E_z$-field distributions at selected frequencies

Figure 9. Simulated EzE_z-field distributions at a few selected frequencies of (a) 48, (b) 60, (c) 70, and (d) 85 GHz. At frequencies of 48 and 60 GHz, the EzE_z-field distribution is concentrated around the periphery of each meta-unit. However, the EzE_z-field is spatially distributed within the surface lattice at 70 and 85 GHz, showing the effect of the trapped surface wave of the hh-th harmonic.

For a fixed spacing of P=3P = 3 mm, the square pattern size (aa) serves as a determining parameter for the operating frequency of the fundamental resonance, as shown in Figure 10(a) and (b). Meanwhile, Figure 11 shows that the periodic structure resonances can be varied on the certain condition of aa. Due to the relatively small size of the pattern compared to the periodicity, higher-order harmonic modes within the periodic structure are challenging to excite with significant intensity. Instead, the fundamental resonance induced by the square patterns predominantly governs the surface lattice behavior. The influences for the unit dimension of the metasurface are easily described by the impedance matching concept of the ECN model, which approximates the relative dominance of the eigenmodes into the impedance parameters.

Reflection coefficient of the periodic metasurface

Figure 10. Reflection coefficient of the periodic metasurface as a function of the square pattern size (a) calculated by (a) 3D FEM simulation and (b) ECN model approach

Variation of peak points and transverse resonances in the reflection coefficient regarding to the square pattern size

Figure 11. Variation of peak points and transverse resonances in the reflection coefficient regarding to the square pattern size aa.

As shown in Figure 12(a) and (c), the variation of the square pattern size is not related to the singularity positions of the resistances for the hh-th harmonics at all, since the parameters are only determined by the periodicity. In terms of the reactance part, Figure 12(b) and (d) show the zero-crossing points are invariant by changes of aa. Meanwhile, the reactance of the fundamental resonance caused by the metasurface is widely spread within the overall frequencies for a≤0.7a \leq0.7 mm, as shown in Figure 13(a) and (c). Figure 13(b) and (d), the total input impedance less than the certain size of aa is decided by considering the reactance variation of the fundamental resonance, where the tendency is similar to the variations of the peak points in Figure 10. The flat reactance for a>0.7a > 0.7 mm represents that the fundamental resonance loses its dominance in the periodic structure, due to the increasing coupling of the higher order of the space harmonics. In terms of the conditional size of aa and PP, the fundamental and higher-order resonances of the metasurface can be controlled by independent parameters corresponding to each resonance.

Resistances and reactance components of the input impedance

Figure 13. Resistances of (a) the fundamental resonance and (b) total input impedance (YinY_{\mathrm{in}}) regarding to the square pattern size aa and the overall frequencies. Reactance components of (c) the fundamental resonance and (d) total input impedance (YinY_{\mathrm{in}}) for certain values of the parameter aa.

Resistance and reactance in the input impedance of the Floquet harmonics

Figure 12. (a) Resistance and (b) reactance in the input impedance of the Floquet harmonics regarding to the square pattern size (aa) and the overall frequencies. (c) Resistance and (d) reactance components of the input impedance associated with the Floquet harmonics for certain values of the parameter aa, which exhibit singularities that remain invariant under fixed periodic modulation

Effect of Material Loss for Trapped Surface Waves

Material losses, such as dielectric loss, are major parameters in including the overall attenuation over the trapped surface waves distributed in the periodic structure, as illustrated in Figure 9(a). Increasing a dielectric loss is effective to increase the quality factor of the reflection response for the hh-th harmonics and strengthen the absorption property, as illustrated in Figure 14(a). The relationship can be specified by the periodic waveguide shorted at the back (z=−dz=-d), considering no coupling between the higher-order modes inside the cavity. For the zz-direction propagating component inside the periodic waveguide, the transverse electric field of eˉh(x,y)\bar{e}_{h}(x,y) excited by the metasurface is given by

Reflection coefficient and resistance component of the metasurface

Figure 14. (a) Reflection coefficient of the metasurface based on a dielectric material varies as increasing Im{εr}{\mathop{\rm Im}\{\varepsilon_r\}} of the permittivity (εr\varepsilon_r). (b) The resistance component of (ZeqZ_{\mathrm{eq}}) corresponding to the partial harmonics, is analyzed for cases where the imaginary part (εr′′\varepsilon_r^{\prime\prime}) of the permittivity takes values of 0.1, 0.2, and 0.3.

Eˉh(x,y,z)=Nheˉh(x,y)(A+e−jβz,h(a)z+A−ejβz,h(a)z)(4)\bar{E}_{h}(x,y,z)=N_{h}\bar{e}_{h}(x,y)\left(A^{+}e^{-j\beta_{z,h}^{(a)}z}+A^{-}e^{j\beta_{z,h}^{(a)}z}\right) \tag*{(4)}

where the coefficient of A+A^{+} and A−A^{-} are arbitrary amplitudes of the forward and backward traveling waves. Using the condition that Eˉh(x,y,0)=Nheˉh(x,y)\bar{E}_{h}(x,y,0)=N_{h}\bar{e}_{h}(x,y) implies that A+=1−A−A^{+}=1-A^{-} on the metasurface. The Floquet harmonics become evanescent and exponentially decay in the free-space. Then, the condition Eˉh=0\bar{E}_{h}=0 at z=−dz=-d leads to the coefficient

A−=ejβz,h(a)ejβz,h(a)d−e−jβz,h(a)d.(5)A^{-}=\frac{e^{j\beta_{z,h}^{(a)}}}{e^{j\beta_{z,h}^{(a)}d}-e^{-j\beta_{z,h}^{(a)}d}}. \tag*{(5)}

Considering the attenuation inside the dielectric/magnetic substrate of each periodic boundary, the transverse fields for the Floquet modes can be written as

Eˉh(x,y,z)=Nheˉh(x,y)ejβ˙z,h(a)(z+d)−e−jβ˙z,h(a)(z+d)ejβ˙z,h(a)d−e−jβ˙z,h(a)d=Nheˉh(x,y)e−jβ˙z,h(a)(z+d)2jsin⁡βz,h(a)d1−e2jβ˙z,h(a)(z+d)1−e2jβ˙z,h(a)d,(6)\begin{aligned} \bar{E}_{h}(x,y,z)&=N_{h}\bar{e}_{h}(x,y)\frac{e^{j\dot{\beta}_{z,h}^{(a)}(z+d)}-e^{-j\dot{\beta}_{z,h}^{(a)}(z+d)}}{e^{j\dot{\beta}_{z,h}^{(a)}d}-e^{-j\dot{\beta}_{z,h}^{(a)}d}}\\ &=N_{h}\bar{e}_{h}(x,y)\frac{e^{-j\dot{\beta}_{z,h}^{(a)}(z+d)}}{2j\sin\beta_{z,h}^{(a)}d}\frac{1-e^{2j\dot{\beta}_{z,h}^{(a)}(z+d)}}{1-e^{2j\dot{\beta}_{z,h}^{(a)}d}}, \tag*{(6)} \end{aligned}
β˙z,h(a)=βz,h(a)[1−jtan⁡δϵ+tan⁡δμ2{βz,h(a)}2{βz,h(a)}2](7)\dot{\beta}_{z,h}^{(a)}=\beta_{z,h}^{(a)}\left[1-j\frac{\tan\delta_{\epsilon}+\tan\delta_{\mu}}{2\{\beta_{z,h}^{(a)}\}^{2}}\{\beta_{z,h}^{(a)}\}^{2}\right] \tag*{(7)}

where the complex wavenumber considering the material loss is denoted as β˙z,h(a)\dot{\beta}_{z,h}^{(a)}. The attenuation part within the traveling wave leads to decay in the magnitude of the propagating normal waves of all the harmonics, which is reflected in decreasing the resistance of each harmonic as shown in Figure 14(b). For a higher loss, the reflection response with a rapidly change for the higher frequency band can be designed in terms of the absorption, as suppressing the impedance of each harmonic contributes to extending the impedance matching region. It is notable that the variation of the loss properties has an effect on improving the quality factor of the periodic structure resonance, as well as that of the fundamental resonance.

Novel Absorbing Property Based on Frequency Selective Material

Novel Absorbing Mechanism Combining Trapped Surface Waves and Magnetic Substrate

When using conventional dielectric substrates, the absorption band appears in a narrow region characterized by rapid

phase changes corresponding to a higher quality factor. Furthermore, an increase in dielectric loss can impede the effective design of both the fundamental resonance and the periodic structure resonances. The growth of reflection loss adversely makes the reflection surface design in the lower operation challenging, as it severely degrades the propagation within the designated region. Besides, the dielectric substrates faces inherent physical limitations in achieving a higher dielectric loss itself. To overcome the physical limitations associated with dielectric substrates, the introduction of new materials, such as those varying in magnetic loss properties, is necessary [50, 51, 52, 53]. As shown in Figure 15(a), a virtual material is assumed in introducing a variation of certain magnetic losses such as [54]. The imaginary part (μr′′\mu_{r}'') of the permeability depending on the frequency variation can be given as

Resistance and reflection coefficient responses for three cases

Figure 15. (a) Resistance part of ZeqZ_{\mathrm{eq}} considering an arbitrary function (8) with respect to Im⁡{μr}\operatorname{Im}\{\mu_{r}\}. Case 1 where fc=65f_{c}=65 GHz, case 2 where fc=70f_{c}=70 GHz, and case 3 where fc=75f_{c}=75 GHz. (b) Reflection coefficient of the metasurface with a virtual material comparing to the dielectric material, where an arbitrary function (8) of Im⁡{μr}\operatorname{Im}\{\mu_{r}\} is applied.

μr′′=p×e−k(f−fc)2,(8)\mu_{r}''=p\times e^{-k(f-f_{c})^{2}}, \tag*{(8)}
k=ln⁡2(fhalf−fc)2(9)k=\frac{\ln2}{(f_{\mathrm{half}}-f_{c})^{2}} \tag*{(9)}

where pp is denoted as the peak amplitude of μr′′\mu_{r}'', and the order (kk) is determined by the half-magnitude bandwidth, from fc−fhalff_{c}-f_{\mathrm{half}} to fc+fhalff_{c}+f_{\mathrm{half}}, adjacent to the center frequency (fcf_{c}). As shown in Figure 15(a), the properties of the material can be reflected as a decrease of the input impedance (ZeqZ_{\mathrm{eq}}) within a specific region. If a material exhibits magnetic loss within the frequency band for which the trapped surface waves propagates, the previously undesignated region can be transformed into an absorbing region, as shown in Figure 15(b). The roll-off property or absorption bandwidth of the absorbing region can be designed by manipulating the magnetic loss function and the reflection response of the hh-th harmonics. Case 3 is possible to achieve the sharper roll-off in front of the start of the absorption band comparing to the other cases. Meanwhile, the absorption band of the case 1 has a dual-band operation.

To realize the virtual material and the loss function, M-type ferrites with a loss function similar to the virtual material need to be designed and fabricated. As shown in Figure 16(a) and (b), the ferromagnetic resonance (FMR) of the ferrite substrate can be adjusted by controlling the doping concentration of Al ion [55], while the permeability of that remains invariant. Utilizing this tunable property, the FMR frequency of the Mtype ferrite material is closely aligned with the transverse resonances of ftr1f_{\mathrm{tr1}} and ftr2f_{\mathrm{tr2}}, which achieves a continuous absorption band such as Case 3 in Figure 15(b). As shown in Figure 17(a) and (b), the integration of the ferrite substrate and the metasurface with periodic structure enhances the absorption bandwidth compared to a single slab of M-type ferrite without a metasurface. Interestingly, the metasurface with a ferrite substrate maintains a stable operating bandwidth of its absorption, although the patch size aa varies between 0.7 and 1.2 mm. This is because the square width change more than a certain size is capable of exciting the normal propagating waves of the Floquet harmonics with a coupling ratio of the comparable intensity for the fundamental resonance, as shown in Figure 13(a) and (c). In terms of the equivalent resistance in Figure 18(a), the transverse resonances caused by the trapped surface waves are located at constant frequencies for varying the pattern size (aa). Utilizing the M-type ferrite under the metasurface allows us to specify the continuous bandwidth for the absorption property.

Permittivity and permeability plots for SrFe$_{12-x}$Al$_x$O$_{19}$ at different doping concentrations

Figure 16. (a) Permittivity and (b) permeability of the M-type ferrite depending on the doping concentration of Al ion.

Reflection coefficient contour plots for the equivalent circuit network and full-wave electromagnetic simulation

Figure 17. Reflection coefficient of the metasurface with periodic structure based on the M-type ferrite as a function of the square pattern (a) calculated by (a) 3D FEM simulation and (b) ECN model approach.

Resistance and reactance of the equivalent impedance for different patch sizes and harmonic contributions

Figure 18. (a) Resistance part of ZeqZ_{\mathrm{eq}} considering the different sizes of the patch pattern. (b) Reactance part of ZeqZ_{\mathrm{eq}} considering the impact of the fundamental resonance and the periodic structure resonances for the hh-th harmonics. It is clear that the pattern size needs to be set as 0.9 mm to achieve the continuous impedance matching within a desired region.

The EzE_z-field distribution should be addressed to specify the operation of the fundamental resonance and periodic structure resonances. As shown in Figure 19(a) and (b), the EzE_z-field distribution of the fundamental resonance for the metasurface with periodic structure is similar with that observed within the dielectric substrate. The field distribution for a change of the metasurface substrate is invariant, located around the edge of each meta-unit. The M-type ferrite based metasurface in the lower frequency can be designed into a reflective surface for tiling the incident wave. The EzE_z-field distribution of Figure 19(c) and (d) shows that the periodic structure resonances in the higher frequencies become intensive based on the M-type ferrite, comparing to the dielectric substrate. In case of the M-type ferrite, the surface current is hard to be induced on the metasurface within the higher frequencies due to the mode matching between the fundamental resonance and the periodic structure of the Floquet harmonics. The EzE_z-field distributions of the Floquet harmonics propagate along the metasurface inside the periodic wall without the fundamental resonance of the metasurface.

Simulated $E_z$-field distributions at selected frequencies

Figure 19. Simulated EzE_z-field distributions at a few selected frequencies of (a) 48, (b) 60, (c) 70, and (d) 85 GHz in case of the M-type ferrite substrate. At frequencies of 48 and 60 GHz, the EzE_z-field distribution is concentrated around the periphery of each meta-unit. The EzE_z-field is spatially distributed within the surface lattice at 70 and 85 GHz, which is derived from the influence of the trapped surface wave of the hh-th harmonic.

Controlling Ferromagnetic Resonance Frequency of M-type Ferrite

The new material needs to be introduced in order to overcome the physical limitation when using the dielectric substrate. If a magnetic material has a magnetic loss in the frequency band that traps higher-order modes, the undesignated region can be changed to the absorbing region, as shown in Figure 3. This desired high magnetic loss in a specific frequency band can be induced from ferromagnetic resonance (FMR) of the ferromagnetic materials. While the magnetic materials induce a significant loss of the electromagnetic wave at the FMR frequency via coupling between the wave and the magnetization of the ferromagnetic material, most magnetic materials including Fe, Co, and spinel ferrites have a low FMR frequency below several GHz [56]. However, M-type ferrites are known to exhibit FMR at over 45 GHz due to their high magnetic anisotropy (HaH_a) compared to other magnetic materials, as the FMR frequency is proportional to HaH_a of the magnetic material [57].

The authors’ group has been interested in controlling the FMR frequency of M-type ferrites by substituting Fe ions into various transition metal ions and inducing increased/decreased HaH_a. According to previous research by the authors, substitution of Co-Ti in M-type strontium ferrites (SrFe12_{12}O19_{19}) decreases the frequency of FMR while Al increases the FMR frequency [55]. There are five different lattice sites for Fe ions in M-type ferrites: 2a, 2b, 12k, 4f1, and 4f2 (Figure 20). During ion substitution, the Co-Ti ions prefer to occupy the 4f2 and 2b sites, while the Al ions prefer to occupy 12k and 2a sites [58], [59]. As each site has different contribution to the ferrite’s magnetic properties including saturation magnetization (MsM_s), coercive field (HcH_c), and magnetocrystalline anisotropy constant (K1K_1), we can observe HaH_a and FMR frequency changes [60]. For example, the substitution of nonmagnetic Al to magnetic Fe ions results in a decrease MsM_s and a rise K1K_1, leading to an increase HaH_a and a blueshift of the FMR frequency.

Crystallographic structure of M-type strontium ferrite

Figure 20. Crystallographic structure of M-type strontium ferrite, containing five different Fe sites: (1) octahedral 2a site with up-spin, (2) trigonal bipyramidal 2b site with up-spin, (3) tetrahedral 4f1 site with down-spin, (4) octahedral 4f2 site with down-spin and (5) octahedral 12k site with up-spin. Due to the antiparallel arrangement of spins, the MsM_s and HaH_a of M-type strontium ferrite are affected in different ways depending on which site the localized Fe3+^{3+} ions occupy.

In this study, to absorb the 77 GHz band, SrFe10.5_{10.5}Al1.5_{1.5}O19_{19} ferrites were synthesized by substituting 1.5 Fe ions of SrFe12_{12}O19_{19} into 1.5 Al ions during the M-type strontium ferrite synthesis process. The detailed synthesis procedure is described in the previous work of the authors [55]. A ferrite composite solution was prepared by mixing 70 wt% of SrFe10.5_{10.5}Al1.5_{1.5}O19_{19} with 30 wt% of TPU solution using a planetary mixer (ARE-310, Thinky). The composite solution was cast into 100 μ\mum thick layers by bar coating. A magnetic substrate was obtained by stacking these composite layers at a desired thickness and pressing at 120 °C with 10 MPa for 20 minutes.

Reflectsorber Based on M-Type Ferrite

Design

The combination of the M-type ferrite slab with the metasurface offers distinct frequency-division properties, preserving the designated operation of the metasurface with periodic structure in the lower frequency bands. When the field distributions are compared in Figure 9 and Figure 19, the ferrite substrate primarily is related to higher frequencies and does not affect the metasurface operation in the lower bands, which stems from its material characteristics. The M-type ferrite substrate behaves similarly to a dielectric material without variations in relative permeability, that is, its μr=1\mu_r = 1, as the permeability property of M-type ferrite is not able to be sustained below its FMR frequency. The variation of the metasurface pattern, satisfying a proper ratio of aa to PP, determines a phase variation of the fundamental resonance in the lower frequency region. The beam-modulating designs, such as beam-shifting, anomalous reflection, and beam-scattering, can be applied to the lower-band operation of the metasurface. In addition, a fixed periodicity of the metasurface based on the M-type ferrite provides a constant absorption band even on the variation of the pattern size (aa).

A simple device, referred to synthetically as a reflectsorber—a term that encapsulates its dual functionality as both a reflectarray and an absorber—is proposed and shown in Figure 21(a). The sheet impedances (YesY_{\mathrm{es}} and ZmsZ_{\mathrm{ms}}) of the metasurface are given by the reflection coefficient (Γ\Gamma), since the transmittance is effectively zero due to the ground plane at the bottom of the metasurface [61]. Also, This configuration ensures that the reflection coefficients in both the xx- and yy-directions (Γ=Γxx=Γyy\Gamma= \Gamma_{xx} = \Gamma_{yy}) are equal, due to the symmetric shape of the elements. The reflectarray metasurface can be designed by tailoring the reflection phase of each meta-unit based on conventional array theory [62]. To realize beam steering with a 1-bit coding scheme, the elements must provide two distinct reflection phases—typically 0° and 180°. In Figure 21(b), the 1-bit meta-atoms designed with lateral dimensions of a0=1.0a_0 = 1.0 mm and a1=0.8a_1 = 0.8 mm yield a phase difference of 180°. The radiation pattern in Figure 21(c) illustrates that the metasurface works as the reflectarray with the horn antenna operating in the U-band.

Figure 21. (a) Multi-functional metasurface with the reflectarray and the absorbing property. (b) Reflection coefficient of 1-bit unit-cells with the same absorption region, representing that the phase variation of the dominant mode is decided by aa. (c) Scattered beam-patterns of the reflectarray and the absorber functions corresponding to the lower frequency band and the higher frequency, respectively. The incident wave of the reflectarray and the absorber are designed as a feeding horn of 53 GHz and a incident plane wave, respectively. (d) Absorption performance of the metasurface under the normal incidence. The non-designated region can be changed into the absorption region, which is only achieved by combining the metasurface with the ferrite material.

The unit cell periodicity should satisfy the condition of P<λ0/2P < \lambda_0/2 within the lower frequencies, which guarantees no grating lobe and continuous phase distribution. The periodicity of 3 mm is enough to ensure the radiation performance of the metasurface. In addition, a constant absorption band can be achieved by combining the metasurface with the M-type ferrite in the case of P=3P = 3 mm in a higher frequency operation. As shown in Figure 21(c), the absorbing property in the higher frequency is validated by the degraded intensity of the scattered radiation for the incident wave. The absorbing property is designated in the higher operating band despite considering the reflectarray design within the metasurface, as depicted in Figure 21(d). The FMR of the M-type ferrite is adjustable in V-band by modifying the Al ion concentration, as demonstrated in Supplementary Fig. S6. Once the operation band of the absorption capability is confirmed, the center frequency of the reflective region is defined by the resonance frequency of the 1-bit elements. For the reflectsorber with a periodicity of 3 mm, the operation frequency of the reflective regime ranges from 38 to 52 GHz by adjusting the patch size from 0.8 to 1.2 mm, as shown in Figure 17.

Measurement Results

To validate the theoretical approach of the reflectsorber, the metasurface was designed with a reflectarry operation of 38 GHz and the absorption operation of 78 GHz, which is based on the 1-bit unit cell of a0=1.1a_0 = 1.1 mm and a1=1.3a_1 = 1.3 mm in P=3.2P = 3.2 mm. The screen printing method was used directly to fabricate the metasurface printed on the M-type ferrite. Figure 22(a) shows the fabricated reflectsorber based on the M-type ferrite slab with the FMR frequency of 70 GHz. The designed absorber consists of a circular pattern with a radius of 20 unit cells, each measuring 0.41×0.41λ020.41 \times0.41\lambda_0^2.

Figure 22. (a) Far-field experimental setup and fabricated reflectsorber sample to measure the radiation performance of the reflectsorber. (b) Simulated and measured realized gain of the reflectsorber at ϕ=0∘\phi= 0^\circ and 39 GHz. (c) Contours of simulated and measured realized gain of the reflectsorber at 39 GHz. (d) Absorption performance comparing the simulation with the measurement under the normal incidence.

In the first measurement, the radiation performance of the reflectsorber was tested in the anechoic chamber, as shown in Figure 22(a). The main peak of reflection toward the receiving antenna occurs at θ=25∘\theta= 25^\circ. This is an expected result, meaning that the designed metasurface works as a reflectarray. Material losses from screen printing for patterning the metasurface contribute to a 0.5 dB difference predicted between the peak gain. The measured pattern of the ϕ=0∘\phi= 0^\circ cut plane at 39 GHz agrees well with the simulations, as depicted in Figure 22(b). Also, the contour pattern in Figure 22(c) represents the radiation performance similar to the expectation was exactly realized in utilizing the M-type ferrite and the metasurface with periodic structure. For applications where a circular polarization is required, the metasurface is capable to radiate the circularly polarization by using a circularly polarized feed antenna.

In the second experiment, the absorption property can be validated by the reflection ratio for the metasurface under the incident wave compared to that of the reference metal plate. To measure the scattering parameters of the absorbers, a vector network analyzer (Keysight N5291A) was used with a focusing lens antenna (FS-110, EM Labs) for the free space measurement method in the range of 18 ∼\sim 110 GHz. A time-gating technique was implemented to eliminate background noise and other potential effects, retaining only the signal reflected from the metasurface. Figure 22(d) shows the measurement of absorption performance under normal incidence at V- and W-bands. As expected in both the theoretical and the simulated results, the metasurface can be spanning 63 ∼\sim 82 GHz with a fractional bandwidth of 26.2%, encompassing a commercial radar frequency of 77 GHz band. The proposed absorption mechanism can be verified by the measurement, which matches well with the simulation. The metasurface has the relative thickness of 0.083λ0\lambda_0, where λ0\lambda_0 is the free-space wavelength at the low frequency in the operating band. By adhering to Rozanov’s limitation, the absorption bandwidth ratio to the structure’s thickness is constrained, which means that thinner absorbers tend to have narrower absorption bandwidth [63]. For an actual application, the reflectsorber can be utilized to suppress the high level of harmonic radiation for feeding antenna, such as microstrip antenna. Also, the absorption property of the reflectsorber is capable to work as a planar filter, which is effective to mitigate an external interference, without the additional design for introducing a filtering structure.

Metasurface Combining Anomalous Reflective Behavior and Absorbing Property

Design

An additioanl example of this configuration is to integrate the novel absortive property with anomalous reflectior analyzed in [26], demonstrating the anomalous reflective behavior of the metasurface realized by a 1-bit element for an incident plane wave. The period of the metasurface that satisfies kg=k0(sin⁡θr−sin⁡θi)=2π/λgk_g = k_0(\sin\theta_r-\sin\theta_i)=2\pi/\lambda_g is crucial to support the anomalous reflection caused by the propagation of the diffraction modes. As described in [26], the number of outgoing diffraction modes is determined by

M=1+⌊1−sin⁡θi∣sin⁡θr−sin⁡θi∣⌋+⌊1+sin⁡θi∣sin⁡θr−sin⁡θi∣⌋(10)M = 1 + \left\lfloor\frac{1-\sin\theta_i}{\left\lvert\sin\theta_r-\sin\theta_i\right\rvert} \right\rfloor+ \left\lfloor\frac{1+\sin\theta_i}{\left\lvert\sin\theta_r-\sin\theta_i\right\rvert} \right\rfloor \tag*{(10)}

where ⌊⋅⌋\lfloor\cdot\rfloor indicates the floor (round down) operation. In the case of the region shaded in blue, high-efficiency anomalous reflection is achievable with two elements per guided wavelength λg\lambda_g (M=2M = 2) [26], as shown in Figure 23(a). For anomalous reflection, the set of incident angle (θi\theta_i) and reflected angle (θr\theta_r) is selected and designed within the shaded region. The periodicity (P=λg/2P=\lambda_g/2) has to be meticulously considered to ensure effective operations of both the designated region and the emergent absorption feature. The chosen set of θi\theta_i and θr\theta_r should meet the following condition, which governs the absorbing properties of the metasurface:

Figure 23. (a) The number (MM) of outgoing diffraction modes and the realization region in supporting the dual-operation based on the ferrite substrate with the FMR of 74 GHz. (b) The reflection coefficient for varying aa is represented on the Smith chart, and the parameters (a1,a2a_1, a_2) are selected for the metasurface design. (c) Absortpion performance as the unit-cell size of metasurface varies under the normal incidence. The non-designated region in the higher-frequency band can be changed into an absorption region, which is only achieved by combining the metasurface with the ferrite material. (d) Simulated scattering of a finite metasurface as the unit-cell size (PP) varies. The desired reflected angle can be tuned by the unit-cell size. (e) The corresponding 1-D normalized intensity on th e frequencies of 47, 48, and 49 GHz.

λ0LO/Pmax⁡≤∣sin⁡θr−sin⁡θi∣≤λ0LO/Pmin⁡(11)\lambda_0^{\mathrm{LO}}/P_{\max} \leq\left\lvert\sin\theta_r-\sin\theta_i\right\rvert\leq\lambda_0^{\mathrm{LO}}/P_{\min} \tag*{(11)}

where the free-space operating wavelength of the reflective mode in lower frequency is λ0LO\lambda_0^{\mathrm{LO}}. For the transverse resonances in Fig. (b), the maximum and minimum of the unit-cell size are given as

ftr1(Pmin⁡)≤fFMR≤ftr2(Pmax⁡)(12)f_{\mathrm{tr1}}(P_{\min}) \leq f_{\mathrm{FMR}} \leq f_{\mathrm{tr2}}(P_{\max}) \tag*{(12)}

where the continuous absorption band can be obtained by fixing the periodicity of the metasurface. For example, when considering an M-type ferrite substrate with FMR frequency of 70 GHz, unit cell sizes are determined to be a minimum (Pmin⁡P_{\min}) of 3.0 mm and a maximum (Pmax⁡P_{\max}) of 3.6 mm. The patterned area in Figure 23(a) shows the specified region desired to achieve the realization of the anomalous reflective property (λ0LO\lambda_0^{\mathrm{LO}}) and the absorbing property (λ0HI\lambda_0^{\mathrm{HI}}), when using a ferrite substrate with an FMR frequency of 75 GHz. The metasurface integrated with a ferrite slab can be engineered to reflect a TE-polarized wave with 40° into an anomalous reflection with 23°. For a patch size where a=ba=b, Figure 23(b) represents the reflection coefficient as aa is varied from 0.8 to 1.3 mm in λ0LO\lambda_0^{\mathrm{LO}}. There is a reflection loss caused by the dielectric loss of tan⁡δ=ϵr′′/ϵr′\tan\delta=\epsilon''_r/\epsilon'_r, which has an impact on the overall frequency band. The 1-bit elements with a1a_1 and a2a_2 are determined to be 0.85 mm and 1.03 mm, respectively, to achieve anomalous reflection. The phase difference between the 1-bit elements needs to be 180° to reduce specular reflection. Furthermore, with a fixed unit cell periodicity, the metasurface elements maintain similar frequencies for the absorbing operation in the higher-order mode, even when the patch size is varied. As shown in Figure 23(c), the metasurface on a ferrite substrate with a FMR frequency of 73 GHz exhibits a broader absorption bandwidth under variations in PP, with bandwidths of 11 GHz, 17 GHz, and 14 GHz at PP values of 2.8, 3.0 and 3.2 mm, respectively. In contrast, when only the ferrite slab is used, the bandwidth narrows significantly to only 2.8 GHz. Specular reflection is suppressed across a frequency range from 47 to 49 GHz as PP varies from 2.8 to 3.2 mm. For further reduction of specular reflection at P=3.2P=3.2 mm, the dimensions of the 1-bit elements need to be finely re-optimized from a1a_1 and a2a_2, considering deviations in a mutual coupling between 1-bit unit cells. The reflected angle can be adjusted by tuning the guided diffraction modes, which change with the unit cell size, as illustrated in Figure 23(d) and (e) [64]. The metasurface achieves an anomalous reflection with a power efficiency of 60%, taking into account the inherent reflection loss of the substrate.

Measurement results

To validate the theoretical approach of the proposed metasurface, the modulated surface was designed with an anomalously reflective operation of 39 GHz and the absorption operation of 78 GHz, which is based on the 1-bit unit cell of a0=1.05a_0 = 1.05 mm and a1=1.2a_1 = 1.2 mm in P=3.2P = 3.2 mm.

The screen printing method was used directly to fabricate the metasurface printed on the M-type ferrite. Figure 24(a) shows the metasurface fabricated based on the M-type ferrite slab with a FMR frequency of 74 GHz. The designed absorber consists of a square pattern with 30 unit cells, where each cell is measured as the electrical width 0.41×0.41λ020.41 \times0.41\lambda_0^2 corresponding to the lower-band operation.

Figure 24. (a) Fabricated metasurface sample. (b) Ka-band bi-static experimental setup in a semi-anechoic chamber to measure the radiation performance of the designed metasurface. (c) Measured signals when varying the orientation angle θ\theta of the receiving antenna for the metasurface and the reference plate with its same size. (d) Contours of simulated and measured normalized intensity of the metasurface for reflected angle (θ\theta) and frequency band of 35–40 GHz. (e) Absorption performance comparing the simulation with the measurement under the normal incidence.

In the first measurement, the reflection characterization of the metasurface was tested in the semi-anechoic chamber, as shown in Figure 24(b). In the bi-static measurement setup, the 3D-printed lens horn antennas with 23 dBi at 39 GHz were used to collimate the energy for receiving and transmitting the electromagnetic wave. The metasurface was placed at a distance of 50 cm (about 65λ65\lambda at 39 GHz) from the antennas. The distance is enough to satisfy the far-field condition, where the radiation from the antenna can be approximated as a plane wave. The receiving antenna was rotating along the bridge in the range of −75∘-75^\circ to 75∘75^\circ with a setup of 5∘5^\circ. The main peak of reflection toward the receiving antenna occurs at θ=25∘\theta= 25^\circ, as depicted in Figure 24(c). This is an expected result, meaning that the designed metasurface works as an anomalous reflection. The material losses of M-type ferrite and the surface roughness caused by the screen printing contribute to a difference of 4 dB compared to the metal plate. In addition, the contour pattern in Figure 24(d) represents the reflection ability similar to the expectation was exactly realized, although the anomalous reflective metasurface was designed and fabricated on the M-

type ferrite.

In the second experiment, the absorption property can be validated by the reflection ratio for the metasurface under the incident wave compared to that of the reference metal plate. To measure the scattering parameters of the absorbers, a vector network analyzer (Keysight N5291A) was used with a focusing lens antenna (FS-110, EM Labs) for the free space measurement method in the range of 18 ∼ 110 GHz. A time-gating technique was implemented to eradicate background noise and other potential effects, retaining only the signal reflected from the metasurface. Figure 24(e) shows the measurement of absorption performance under normal incidence at V- and W-bands. As expected in both the theoretical and simulated results, the metasurface can be spanning 69 ∼ 83.5 GHz. The proposed absorption mechanism can be verified by the measurement, which matches well with the simulation.

Conclusion

This paper has provided a comprehensive review and tutorial on multi-functional metasurfaces integrated with M-type ferrite materials for millimeter-wave (mmWave) absorption and beam control. As wireless communication moves toward beyond-5G systems and incorporates non-terrestrial networks (NTNs), adaptive, low-profile electromagnetic surfaces capable of managing interference and enabling dynamic beam reconfiguration have become essential. This work have highlighted the limitations of conventional metasurfaces, particularly their challenges in simultaneously achieving wideband absorption and beamforming due to inherent material and structural constraints.

The review emphasized recent advances in multi-functional metasurface designs, showcasing the integration of frequency-selective magnetic materials and periodic surface lattices to realize passive, compact, and reconfigurable electromagnetic devices. Special attention was given to the novel metasurface based on M-type ferrite materials, demonstrating their significant role in enhancing absorption through ferromagnetic resonance, alongside surface-wave trapping mechanisms to achieve both narrowband and broadband performance. A detailed case study of a ferrite-based hybrid ”reflectsorber,” combining reflectorarray and absorber functionalities, was presented to illustrate critical design principles, analytical methodologies, and practical applications relevant to advanced communications with NTNs such as satellite communications and unmanned aerial vehicles (UAVs).

Equivalent Circuit Network Modeling

It is considered that the metasurface composed of zero-thickness metallic patches lies on either a dielectric or ferrite substrate. As shown in Figure 25(a), a TE-polarized plane wave is incident at an angle θ\theta in the principal yzyz plane of the patch array The impinging field parallel to the periodic structure is in the EE-plane, inducing the surface currents on the metasurface. Reflection and transmission from the metasurface with periodic structure correspond to the interference of an infinite set of propagating and evanescent plane waves, i.e., Floquet harmonics. As shown in Figure 25(b), the propagation of the incident and reflected plane waves can be modeled by the equivalent circuit network (ECN) by waveguide and the impedance matching concepts [46], [47]. When the plane wave arrives at the metasurface with periodic structure, the scattered harmonics can be excited along the surface lattice. The wave numbers (kx,m(k_{x,m} and ky,n)k_{y,n}) in the xx- and yy-axes associated with the Floquet harmonics of order mm and nn are denoted by

Figure 25. (a) Scheme of the patch array of finite thickness under oblique incidence. (b) The patch array is equivalent to the waveguide discontinuity problem with a periodic boundary wall. (c) Equivalent circuit network modeling for computing the scattering parameter S11S_{11}. (d) Magnitude of the reflection coefficient for the structure inside the periodic wall under the normal incidence and the patch array with b=0.5b = 0.5 mm and P=3P = 3 mm, where the metasurface is on the free space.

kx,m=2mπP(13)k_{x,m} = \frac{2m\pi}{P} \tag*{(13)}
ky,n=k0sin⁡θ+2nπP(14)k_{y,n} = k_0 \sin\theta+ \frac{2n\pi}{P} \tag*{(14)}

where mm and nn are integer numbers (m,n=0,±1,±2,…)(m,n = 0, \pm1, \pm2, \ldots), and k0k_0 is the free-space wavenumber. Inside a substrate, the normal wave-number of hh-th harmonic with a mode pair of mnmn are defined as follows:

kz,h(a)={βh(a)={k(a)}2−∣kt,h∣2,k(a)≥∣kt,h∣−jαh(a)=−j∣kt,h∣2−{k(a)}2,k(a)<∣kt,h∣(15)k_{z,h}^{(a)} = \begin{cases} \beta_h^{(a)} = \sqrt{\left\{k^{(a)}\right\}^2-\left|k_{t,h}\right|^2}, & k^{(a)} \ge\left|k_{t,h}\right| \\ -j\alpha_h^{(a)} = -j\sqrt{\left|k_{t,h}\right|^2-\left\{k^{(a)}\right\}^2}, & k^{(a)} < \left|k_{t,h}\right| \end{cases} \tag*{(15)}

where the type of substrate is indicated by the superscript (a)(a). The superscripts (d) and (m) for (a) indicate the dielectric substrate with μr=1\mu_r = 1 and the magnetic substrate with μr≠1\mu_r \ne1, respectively. If the superscript is (0), the substrate is considered to be the free space with ϵr=1\epsilon_r = 1 and μr=1\mu_r = 1. For a lossless material, the harmonics are represented as purely real or purely imaginary wavenumbers, which indicates whether it is a propagating or evanescent wave.

As reported in [46], [47], this phenomenon is analyzed by the equivalent network modeling, which addresses the discontinuities between the substrate and metasurface as shown in Figure 25(a). The metasurface can be coupled with various harmonics, while the incident harmonic (m=0(m = 0 and n=0)n = 0) is scattered on the dielectric/magnetic substrate and the metasurface as shown in Figure 25(b). The Floquet expansion of the electric and magnetic field at the discontinuity plane (z=0)(z = 0) is given by

E(x,y)=(1+R)e0(x,y)+∑h≠0Vheh(x,y)(16)\mathbf{E}(x,y) = (1 + R)\mathbf{e}_0(x,y) + \sum_{h \ne0} V_h\mathbf{e}_h(x,y) \tag*{(16)}
H(0)(x,y)=Y0(0)(1−R)[z^×e0(x,y)]−∑h≠0Yh(0)Vh[z^×eh(x,y)](17)\begin{aligned} \mathbf{H}^{(0)}(x,y) ={}& Y_0^{(0)}(1-R)\left[\hat{\mathbf{z}} \times\mathbf{e}_0(x,y)\right] \\ &- \sum_{h \ne0}Y_h^{(0)}V_h\left[\hat{\mathbf{z}} \times\mathbf{e}_h(x,y)\right] \tag*{(17)} \end{aligned}
H(a)(x,y)=Y0(a)(1+R)[z^×e0(x,y)]−∑h≠0Yh(a)Vh[z^×eh(x,y)](18)\begin{aligned} \mathbf{H}^{(a)}(x,y) ={}& Y_0^{(a)}(1+R)\left[\hat{\mathbf{z}} \times\mathbf{e}_0(x,y)\right] \\ &- \sum_{h \ne0}Y_h^{(a)}V_h\left[\hat{\mathbf{z}} \times\mathbf{e}_h(x,y)\right] \tag*{(18)} \end{aligned}

where RR is denoted as the reflection coefficient of the incident wave, and VhV_h indicates the unknown coefficient of the electric field expansion. In the expansion, both TM and TE harmonic modes are included, with the exception of the incident harmonic (h=0)(h = 0). The index hh represents a surrogate number of the various (n,m)(n,m) harmonics, each characterized by a wave vector kt,h\mathbf{k}_{t,h} and its normalized transverse field eh(x,y)\mathbf{e}_h(x,y). The wave vector is comprised of the Floquet expansion of the field. As expressed in [65], this wave vector and related variables are given by

eh(x,y)=e−jkt,h⋅ρPxPye^h[ρ=xx^+yy^](19)\mathbf{e}_h(x,y)=\frac{e^{-j\mathbf{k}_{t,h}\cdot\boldsymbol{\rho}}}{\sqrt{P_xP_y}}\hat{\mathbf{e}}_h \quad[\boldsymbol{\rho}=x\hat{\mathbf{x}}+y\hat{\mathbf{y}}] \tag*{(19)}
kt,h=kx,mx^+ky,ny^(20)\mathbf{k}_{t,h}=k_{x,m}\hat{\mathbf{x}}+k_{y,n}\hat{\mathbf{y}} \tag*{(20)}
k^t,h=kt,h∣kt,h∣=kx,mx^+ky,ny^kx,m2+ky,n2(21)\hat{\mathbf{k}}_{t,h}=\frac{\mathbf{k}_{t,h}}{\lvert\mathbf{k}_{t,h}\rvert}=\frac{k_{x,m}\hat{\mathbf{x}}+k_{y,n}\hat{\mathbf{y}}}{\sqrt{k_{x,m}^{2}+k_{y,n}^{2}}} \tag*{(21)}
vh={k^t,h,TM harmonics.−z^×k^t,h,TE harmonics.(22)\mathbf{v}_h= \begin{cases} \hat{\mathbf{k}}_{t,h}, & \text{TM harmonics}.\\ -\hat{\mathbf{z}}\times\hat{\mathbf{k}}_{t,h}, & \text{TE harmonics}. \end{cases} \tag*{(22)}

The wave admittances, Yh(a)Y_h^{(a)}, looking into the magnetic substrate and air are given by

Yh(a)=Ht,hEt,h=1η(a){k(a)/βz,h(a),TM harmonics.βz,h(a)/k(a),TE harmonics.(23)Y_h^{(a)}=\frac{H_{t,h}}{E_{t,h}}=\frac{1}{\eta^{(a)}}\begin{cases} k^{(a)}/\beta_{z,h}^{(a)}, & \text{TM harmonics}.\\ \beta_{z,h}^{(a)}/k^{(a)}, & \text{TE harmonics}. \end{cases} \tag*{(23)}

where βz,h(a)=ϵr(a)μr(a)k02−kx,m2−ky,n2\beta_{z,h}^{(a)}=\sqrt{\epsilon_r^{(a)}\mu_r^{(a)}k_0^2-k_{x,m}^2-k_{y,n}^2}, k(a)=ϵr(a)μr(a)k0k^{(a)}=\sqrt{\epsilon_r^{(a)}\mu_r^{(a)}}k_0, and η(a)=η0μr(a)ϵr(a)\eta^{(a)}=\eta_0\sqrt{\frac{\mu_r^{(a)}}{\epsilon_r^{(a)}}} with the impedance of free space, η0\eta_0.

Considering the spatial domain, the surface current excited in the unit cell of the metasurface can be written as

J(x,y;ω)=F(ω)Jp(x,y)=F(ω){cos⁡(πxa)[1−(2xa)2]−1/2rect⁡(yb)x^}(24)\begin{aligned} \mathbf{J}(x,y;\omega)=F(\omega)\mathbf{J}_p(x,y) \\ &=F(\omega)\left\{\cos\left(\frac{\pi x}{a}\right)\left[1-\left(\frac{2x}{a}\right)^2\right]^{-1/2}\operatorname{rect}\left(\frac{y}{b}\right)\hat{\mathbf{x}}\right\} \tag*{(24)} \end{aligned}

This approximation implies that the spatial current distribution Jp(x,y)\mathbf{J}_p(x,y) of the metasurface is independent of the frequency (ω)(\omega). In other words, the frequency dependence can be canceled out in the current distribution of J(x,y;ω)\mathbf{J}(x,y;\omega). Although it may seem rather restrictive, it has been found accurate for single resonant elements in a wide frequency range, as reported in [46], [47], [65]. The approximation is expected to hold up to frequencies below the first high-order resonance of the metasurface in a free-standing case, based on the spatial current distribution under this resonance frequency.

The equivalent circuit network (ECN) analysis of the metasurface, which includes the patch array, is derived by applying the boundary condition at the discontinuity plane (z=0z=0):

Jp(x,y)=z^×[H(a)(x,y)−H(0)(x,y)].(25)\mathbf{J}_p(x,y)=\hat{\mathbf{z}}\times\left[\mathbf{H}^{(a)}(x,y)-\mathbf{H}^{(0)}(x,y)\right]. \tag*{(25)}

By substituting the magnetic field expansions from (17) and (18) into (25) and performing subsequent manipulations, the input impedance (ZeqZ_{\mathrm{eq}}) of the ECN model, as shown in Figure 25(c), can be obtained as

Zeq=∑h≠01∣Nh∣2[Yh(0)+Yh(a)](26)Z_{\mathrm{eq}}=\sum_{h\ne0}\frac{1}{\lvert N_h\rvert^2\left[Y_h^{(0)}+Y_h^{(a)}\right]} \tag*{(26)}
Nh=J~p∗(kt,h)⋅vh(27)N_h=\widetilde{\mathbf{J}}_p^{*}(\mathbf{k}_{t,h})\cdot\mathbf{v}_h \tag*{(27)}

where the turn ratio NhN_h is defined as the coupling between the each harmonic and all the remaining harmonics, and superscript symbol ‘∼\sim’ denotes Fourier transform with respect to (x,y)(x,y).

In the case of the finite dielectric/magnetic slab, the Floquet harmonics (hh) excited on the metasurface propagate inside the dielectric/magnetic substrate with the same harmonic. For each harmonic, the transmission line with the semi-infinite medium on the right sides is replaced by a corresponding cascade of separated sections, as reported in [49]. The admittance Yh(a)Y_h^{(a)} in the equation (26) need to be replaced by the following impedance Yin,h(d/m)Y_{in,h}^{(d/m)}:

Yin,h(d/m)=Yh(a)Yh(a)+jYh(0)tan⁡(βz,h(a)d)Yh(0)+jYh(a)tan⁡(βz,h(a)d)(28)Y_{in,h}^{(d/m)}=Y_h^{(a)}\frac{Y_h^{(a)}+jY_h^{(0)}\tan\left(\beta_{z,h}^{(a)}d\right)}{Y_h^{(0)}+jY_h^{(a)}\tan\left(\beta_{z,h}^{(a)}d\right)} \tag*{(28)}

This equation encompasses the combined effects of both the dielectric/magnetic substrate and the metasurface.

With the ECN model, the reflection coefficient at the discontinuity plane (z=0z=0) is obtained by

S11=Y0(0)−Yin,0−∣N0∣2/ZeqY0(0)+Yin,0+∣N0∣2/Zeq.(29)S_{11}=\frac{Y_0^{(0)}-Y_{in,0}-\lvert N_0\rvert^2/Z_{\mathrm{eq}}}{Y_0^{(0)}+Y_{in,0}+\lvert N_0\rvert^2/Z_{\mathrm{eq}}}. \tag*{(29)}

The excited harmonic is propagating wave with the parallel direction on kh(0)=kx,mx^+ky,ny^+kz,h(0)z^\mathbf{k}_h^{(0)}=k_{x,m}\hat{\mathbf{x}}+k_{y,n}\hat{\mathbf{y}}+k_{z,h}^{(0)}\hat{\mathbf{z}}. The Floquet harmonic of (m,n)=(0,0)(m,n)=(0,0) is always the fundamental mode, which forms the incident wave as shown in Figure 25(b). The variation of the Floquet harmonics with respect to patch dimensions in the free space is analyzed using a patch array with variable aa in P=3P=3 mm as shown in Figure 25(d). This figure demonstrates that the dominant resonance changes with an increase in aa, although the frequency of perfect impedance matching remains unaffected by changes in aa. In particular, total transmission is observed at these TE cut-off frequencies of the first-order harmonic [49].

The unknown coefficient (NhN_h) can be expected from the well-known current profile for specific and canonical geometries [66], such as the rectangular patch. For the patch array under normal incidence case, this empirical expectation of NhN_h remains valid up to the maximum effective wavelengths between the second resonance and the third resonance, i.e., λ≈1+22a\lambda\approx\frac{1+\sqrt{2}}{2}a, and the grating lobe regime (1/P1/P) [47], [65]. From the perspective of the cavity model, the conventional patch resonator exhibits the cavity resonance modes of TM01_{01}, TM11_{11}, and TM20_{20} modes, corresponding to the first resonance (λ≈2a\lambda\approx2a), the second resonance (λ≈2a\lambda\approx\sqrt{2}a), and the third resonance (λ≈a\lambda\approx a), respectively. For instance, a metasurface with a maximum dimension of 1.2 mm, permittivity of ϵr=6.5+j0.21\epsilon_r=6.5+j0.21, and 3 mm cell size can be effectively modeled and managed up to 81.2 GHz, corresponding to the second resonance of the metasurface. Since Floquet harmonics up to this frequency can be engineered, modeling and controlling frequency responses beyond this range presents significant challenges. For each harmonic, the grounded medium on the right sides can be modeled by a corresponding cascade of separated sections with each shorted transmission line corresponding to the harmonic, as reported in [49]. The admittance Yin,h(a)Y_{in,h}^{(a)} in the equation (26) is given by the following equation.

Yin,h(a)=−jYh(a)cot⁡(βz,h(a)d)(30)Y_{in,h}^{(a)}=-jY_h^{(a)}\cot\left(\beta_{z,h}^{(a)}d\right) \tag*{(30)}

This equation encompasses the combined effects of both the dielectric/magnetic substrate and the metasurface.

References

  1. [1]Y. Su, Y. Liu, Y. Zhou, J. Yuan, H. Cao, and J. Shi, “Broadband leo satellite communications: Architectures and key technologies,” IEEE Wirel. Commun., vol. 26, no. 2, pp. 55–61, Apr. 2019.
  2. [2]G. Geraci, D. López-Pérez, M. Benzaghta, and S. Chatzinotas, “Integrating terrestrial and non-terrestrial networks: 3d opportunities and challenges,” IEEE Commun. Mag., vol. 61, no. 4, pp. 42–48, Apr. 2022.arxiv.org/abs/2207.10385
  3. [3]O. Kodheli, E. Lagunas, N. Maturo, S. K. Sharma, B. Shankar, J. F. M. Montoya, J. C. M. Duncan, D. Spano, S. Chatzinotas, S. Kisseleff et al., “Satellite communications in the new space era: A survey and future challenges,” IEEE Commun. Surv. Tutor., vol. 23, no. 1, pp. 70–109, Oct. 2020.arxiv.org/abs/2002.08811
  4. [4]M. Giordani and M. Zorzi, “Non-terrestrial networks in the 6g era: Challenges and opportunities,” IEEE Netw., vol. 35, no. 2, pp. 244–251, Apr. 2020.DOI
  5. [5]G. K. Kurt, M. G. Khoshkholgh, S. Alfattani, A. Ibrahim, T. S. Darwish, M. S. Alam, H. Yanikomeroglu, and A. Yongacoglu, “A vision and framework for the high altitude platform station (HAPS) networks of the future,” IEEE Commun. Surv. Tutor., vol. 23, no. 2, pp. 729–779, Mar. 2021.arxiv.org/abs/2007.15088
  6. [6]S. Alfattani, A. Yadav, H. Yanikomeroglu, and A. Yongacoglu, “Resource-efficient HAPS-RIS enabled beyond-cell communications,” IEEE Wirel. Commun. Lett., vol. 12, no. 4, pp. 679–683, Jan. 2023.arxiv.org/abs/2207.11576
  7. [7]K. Tebkyik, G. K. Kurt, C. Huang, A. R. Ekki, and H. Yanikomeroglu, “Channel estimation for full-duplex RIS-assisted HAPS backhauling with graph attention networks,” in ICC 2021-IEEE International Conference on Communications. IEEE, 2021, pp. 1–6.
  8. [8]Q. Cheng, L. Zhang, J. Y. Dai, W. Tang, J. C. Ke, S. Liu, J. C. Liang, S. Jin, and T. J. Cui, “Reconfigurable intelligent surfaces: Simplified architecture transmitters—from theory to implementations,” Proc. IEEE, vol. 110, no. 9, pp. 1266–1289, Sep. 2022.DOI
  9. [9]H.-X. Xu, X. Han, Y. Li, Y. Sun, Z. Zhao, S. Zhang, and C.-W. Qiu, “Completely spin-decoupled dual-phase hybrid metasurfaces for arbitrary wavefront control,” Aes Photonics, vol. 6, no. 1, pp. 211–220, Dec. 2018.
  10. [10]G. Ding, K. Chen, X. Luo, J. Zhao, T. Jiang, and Y. Feng, “Dual-helicity decoupled coding metasurface for independent spin-to-orbital angular momentum conversion,” Phys. Rev. Applied, vol. 11, no. 4, p. 044043, Apr. 2019.DOI
  11. [11]L.-X. Wu, Q. Hu, X.-Y. Luo, J. Zhao, T. Jiang, K. Chen, and Y. Feng, “Wideband dual-feed dual-polarized reflectarray antenna using anisotropic metasurface,” IEEE Antennas Wirel. Propag. Lett., vol. 21, no. 1, pp. 129–133, Jan. 2021.DOI
  12. [12]J. Zhu and Y. Yang, “3-d printed transmission-reflection-integrated metasurface for spin-decoupled full-space quadruplex channels independent phase modulation,” IEEE Trans. Microw. Theory Tech., vol. 72, no. 8, pp. 4790–4800, Aug. 2024.DOI
  13. [13]M. R. Akram, G. Ding, K. Chen, Y. Feng, and W. Zhu, “Ultrathin single layer metasurfaces with ultra-wideband operation for both transmission and reflection,” Adv. Mater., vol. 32, no. 12, p. 1907308, Feb. 2020.DOI
  14. [14]Y. Zhuang, G. Wang, T. Cai, and Q. Zhang, “Design of bifunctional metasurface based on independent control of transmission and reflection,” Opt. Express, vol. 26, no. 3, pp. 3594–3603, Feb. 2018.DOI
  15. [15]W.-L. Guo, G.-M. Wang, H.-S. Hou, K. Chen, and Y. Feng, “Multifunctional coding metasurface for dual-band independent electromagnetic wave control,” Opt. Express, vol. 27, no. 14, pp. 19196–19211, Jun. 2019.DOI
  16. [16]F. Ahmed, M. I. Khan, and F. A. Tahir, “A multifunctional polarization transforming metasurface for c-, x-, and k-band applications,” IEEE Antennas Wirel. Propag. Lett., vol. 20, no. 11, pp. 2186–2190, Nov. 2021.DOI
  17. [17]P. C. Wu, W. Zhu, Z. X. Shen, P. H. J. Chong, W. Ser, D. P. Tsai, and A.-Q. Liu, “Broadband wide-angle multifunctional polarization converter via liquid-metal-based metasurface,” Adv. Opt. Mater., vol. 5, no. 7, p. 1600938, Feb. 2017.DOI
  18. [18]S. Ghosh, J. Ghosh, M. S. Singh, and A. Sarkhel, “A low-profile multifunctional metasurface reflector for multiband polarization transformation,” IEEE Trans. Circuits Syst. II-Express Briefs, vol. 70, no. 1, pp. 76–80, Jan. 2022.DOI
  19. [19]H. Ahmed, X. Zeng, Y. Wang, H. Bello, N. Iqbal, and R. Nordin, “Multifunctional metasurface polarizers synthesis using effective data generation with adaptive attention and space-to-depth enhanced network,” Adv. Opt. Mater., vol. 12, no. 28, p. 2401220, Jul. 2024.
  20. [20]H. Rauf, B. Kamal, S. Ullah, U. Ali, and L. Matokovits, “Experimental validation of a multi-functional metasurface for 5g and satellite communication,” IEEE Access, vol. 13, pp. 55476–55486, 2025.DOI
  21. [21]H. Pan, L. Qiu, B. Ouyang, S. Zheng, Y. Zhang, Y.-C. Chen, and G. Xue, “Pmsat: Optimizing passive metasurface for low earth orbit satellite communication,” in Proceedings of the 29th Annual International Conference on Mobile Computing and Networking, 2023, pp. 1–15.DOI
  22. [22]Y. Wang, H. Pan, L. Qiu, L. Zhong, J. Liu, R. Ma, Y.-C. Chen, G. Xue, and J. Ren, “Gpms: Enabling indoor gnss positioning using passive metasurfaces,” in Proceedings of the 30th Annual International Conference on Mobile Computing and Networking, 2024, pp. 1424–1438.DOI
  23. [23]K. Qian, L. Yao, X. Zhang, and T. N. Ng, “Millimirror: 3d printed reflecting surface for millimeter-wave coverage expansion,” in Proceedings of the 28th Annual International Conference on Mobile Computing and Networking, 2022, pp. 15–28.
  24. [24]R. Phon and S. Lim, “Dynamically self-reconfigurable multifunctional all-passive metasurface,” ACS Appl. Mater. Interfaces, vol. 12, no. 37, pp. 42 393–42 402, Aug. 2020.DOI
  25. [25]A. Díaz-Rubio, V. S. Asadchy, A. Elsakka, and S. A. Tretyakov, “From the generalized reflection law to the realization of perfect anomalous reflectors,” Sci. Adv., vol. 3, no. 8, p. e1602714, Aug. 2017.
  26. [26]A. M. Wong and G. V. Eleftheriades, “Perfect anomalous reflection with a bipartite Huygens’ metasurface,” Phys. Rev. X, vol. 8, no. 1, p. 011036, Feb. 2018.
  27. [27]M. Movahediqomi, G. Ptitcyn, and S. Tretyakov, “Comparison between different designs and realizations of anomalous reflectors for extreme deflections,” IEEE Trans. Antennas Propag., vol. 71, no. 10, pp. 8007–8017, Oct. 2023.
  28. [28]S. K. Vuyyuru, R. Valkonen, D.-H. Kwon, and S. A. Tretyakov, “Efficient anomalous reflector design using array antenna scattering synthesis,” IEEE Antennas Wirel. Propag. Lett., vol. 22, no. 7, pp. 1711–1715, Jul. 2023.
  29. [29]G. Moreno, A. B. Yakovlev, H. M. Bernety, D. H. Werner, H. Xin, A. Monti, F. Bilotti, and A. Alù, “Wideband elliptical metasurface cloaks in printed antenna technology,” IEEE Trans. Antennas Propag., vol. 66, no. 7, pp. 3512–3525, Jul. 2018.
  30. [30]B. Sima, K. Chen, X. Luo, J. Zhao, and Y. Feng, “Combining frequency-selective scattering and specular reflection through phase-dispersion tailoring of a metasurface,” Phys. Rev. Applied, vol. 10, no. 6, p. 064043, Dec. 2018.
  31. [31]Q. Lv, C. Jin, B. Zhang, and Z. Shen, “Hybrid absorptive-diffusive frequency selective radome,” IEEE Trans. Antennas Propag., vol. 69, no. 6, pp. 3312–3321, Jun. 2020.DOI
  32. [32]H.-F. Huang and S.-N. Li, “High-efficiency planar reflectarray with small-size for oam generation at microwave range,” IEEE Antennas Wirel. Propag. Lett., vol. 18, no. 3, pp. 432–436, Mar. 2019.
  33. [33]B. Li, P. F. Jing, L. Q. Sun, K. W. Leung, and X. Lv, “3d printed oam reflectarray using half-wavelength rectangular dielectric element,” IEEE Access, vol. 8, pp. 142 892–142 899, Aug. 2020.
  34. [34]Y. Huang, X. Li, Z. Akram, H. Zhu, and Z. Qi, “Generation of millimeter-wave nondiffracting airy oam beam using a single-layer hexagonal lattice reflectarray,” IEEE Antennas Wirel. Propag. Lett., vol. 20, no. 6, pp. 1093–1097, Jun. 2021.
  35. [35]Y. Fan, J. Wang, Y. Li, J. Zhang, Y. Han, and S. Qu, “Low-rcs and high-gain circularly polarized metasurface antenna,” IEEE Trans. Antennas Propag., vol. 67, no. 12, pp. 7197–7203, Dec. 2019.DOI
  36. [36]J. Su, W. Li, M. Qu, H. Yu, Z. Li, K. Qi, and H. Yin, “Ultrawideband rcs reduction metasurface based on hybrid mechanism of absorption and phase cancellation,” IEEE Trans. Antennas Propag., vol. 70, no. 10, pp. 9415–9424, Oct. 2022.
  37. [37]M. Azari, S. Solanki, S. Chatzinotas, O. Kodheli, H. Sallouha, A. Colpaert, J. F. M. Montoya, S. Pollin, A. Haqiqatnejad, A. Mostaani et al., “Evolution of non-terrestrial networks from 5g to 6g: A survey,” IEEE Commun. Surv. Tutor., vol. 24, no. 4, pp. 2633–2672, Aug. 2022.
  38. [38]F. B. Mismar and A. Ö. Kaya, “Uncoordinated interference avoidance between terrestrial and non-terrestrial communications,” in ICC 2024-IEEE International Conference on Communications. IEEE, 2024, pp. 1243–1248.
  39. [39]F. Rinaldi, H.-L. Maatanen, J. Torsner, S. Pizzi, S. Andreev, A. Iera, Y. Koucheryavy, and G. Araniti, “Non-terrestrial networks in 5g & beyond: A survey,” IEEE Access, vol. 8, pp. 165 178–165 200, Sep. 2020.
  40. [40]S. Leung, C.-p. Liang, X.-f. Tao, F.-f. Li, Y. Poo, and R.-x. Wu, “Broadband radar cross section reduction by an absorptive metasurface based on a magnetic absorbing material,” Opt. Express, vol. 29, no. 21, pp. 33 536–33 547, Oct. 2021.
  41. [41]Y. Zhao, X. Cao, J. Gao, X. Yao, T. Liu, W. Li, and S. Li, “Broadband low-rcs metasurface and its application on antenna,” IEEE Trans. Antennas Propag., vol. 64, no. 7, pp. 2954–2962, Jul. 2016.
  42. [42]J. Xu, H.-X. Xu, H. Luo, Y. Wang, and C. Wang, “A low-rocs folded reflectarray combining dual-metasurface and rasorber,” IEEE Antennas Wirel. Propag. Lett., vol. 21, no. 12, pp. 2462–2466, Dec. 2022.DOI
  43. [43]L. Zhou and Z. Shen, “Absorptive coding metasurface with ultrawideband backscattering reduction,” IEEE Antennas Wirel. Propag. Lett., vol. 19, no. 7, pp. 1201–1205, Jul. 2020.DOI
  44. [44]S. Caizzone, R. Gergese, E. O. Addo, S. P. Hehenberger, and W. Elmarissi, “Spatial filtering of multipath at gnss reference stations through metamaterial-based absorbers,” IEEE Trans. Aerosp. Electron. Syst., vol. 59, no. 6, pp. 7764–7771, Dec. 2023.DOI
  45. [45]Z. Song, J.-F. Zhu, X. Wang, R. Zhang, P. Min, W. Cao, Y. He, J. Han, T. Wang, J. Zhu et al., “Origami metamaterials for ultra-wideband and large-depth reflection modulation,” Nat. Commun., vol. 15, no. 1, p. 3181, Apr. 2024.
  46. [46]R. Rodriguez-Berral, F. Mesa, and F. Medina, “Analytical multimodal network approach for 2-D arrays of planar patches/apertures embedded in a layered medium,” IEEE Trans. Antennas Propag., vol. 63, no. 5, pp. 1969–1984, 2015.
  47. [47]F. Mesa, R. Rodriguez-Berral, and F. Medina, “Unlocking complexity using the ECA: The equivalent circuit model as an efficient and physically insightful tool for microwave engineering,” IEEE Microw. Mag., vol. 19, no. 4, pp. 44–65, 2018.DOI
  48. [48]B. A. Munk, Frequency selective surfaces: Theory and design. John Wiley & Sons, 2005.
  49. [49]M. Garcia-Viguera, F. Mesa, F. Medina, R. Rodriguez-Berral, and J. L. Gomez-Tornero, “Simplified circuit model for arrays of metallic dipoles sandwiched between dielectric slabs under arbitrary incidence,” IEEE Trans. Antennas Propag., vol. 60, no. 10, pp. 4637–4649, Jul. 2012.
  50. [50]E. A. Gorbachev, L. A. Trusov, L. N. Alyabyeva, I. V. Roslyakov, V. A. Lebedev, E. S. Kozlyakova, O. V. Magdysyuk, A. V. Sobolev, I. S. Glazkova, S. A. Beloshapkin et al., “High-coercivity hexaferrite ceramics featuring sub-terahertz ferromagnetic resonance,” Mater. Horiz., vol. 9, no. 4, pp. 1264–1272, Jan. 2022.DOI
  51. [51]C. Liu, Q. Xu, Y. Tang, Z. Wang, R. Ma, N. Ma, and P. Du, “Zr4+ doping-controlled permittivity and permeability of BaFe12−xZrxO19 and the extraordinary EM absorption power in the millimeter wavelength frequency range,” J. Mater. Chem. C, vol. 4, no. 40, pp. 9532–9543, Sep. 2016.
  52. [52]C. Dong, X. Wang, P. Zhou, T. Liu, J. Xie, and L. Deng, “Microwave magnetic and absorption properties of M-type ferrite BaCoxTixFe12−2xO19 in the Ka band,” J. Magn. Magn. Mater., vol. 354, pp. 340–344, Mar. 2014.DOI
  53. [53]C. Liu, Y. Zhang, Y. Tang, Z. Wang, H. Tang, Y. Ou, L. Yu, N. Ma, and P. Du, “Excellent absorption properties of BaFe12−xNbxO19 controlled by multi-resonance permeability, enhanced permittivity, and the order of matching thickness,” Phys. Chem. Chem. Phys., vol. 19, no. 32, pp. 21 893–21 903, Aug. 2017.DOI
  54. [54]Y. Iijima, Y. Houjou, and R. Sato, “Millimeter wave absorber using M-type hexagonal ferrite,” in IEEE International Symposium on Electromagnetic Compatibility. Symposium Record (Cat. No. 00CH37016), vol. 2. IEEE, 2000, pp. 547–549.
  55. [55]H. Lee, S. H. Ryu, S. J. Kwon, J. R. Choi, S.-b. Lee, and B. Park, “Absorption-dominant mmwave EMI shielding films with ultralow reflection using ferromagnetic resonance frequency tunable m-type ferrites,” Nano-Micro Lett., vol. 15, no. 1, p. 76, Mar. 2023.DOI
  56. [56]J. Snoek, “Dispersion and absorption in magnetic ferrites at frequencies above one Mc/s,” Physica, vol. 14, no. 4, pp. 207–217, May 1948.DOI
  57. [57]D. Ratnam and W. Buesssem, “On the nature of defects in barium ferrite platelets,” IEEE Trans. Magn., vol. 6, no. 3, pp. 610–614, Sep. 1970.
  58. [58]X. Zhou, A. Morrish, Z. Li, and Y. Hong, “Site preference for Co/sup 2+/and Ti/sup 4+/in Co-Ti substituted barium ferrite,” IEEE Trans. Magn., vol. 27, no. 6, pp. 4654–4656, Aug. 1991.DOI
  59. [59]M. Przybylski, J. Zukrowski, I. Harward, and Z. Celinski, “Mössbauer spectroscopy study of Al distribution in BaAlxFe12−xO19 thin films,” Journal of Applied Physics, vol. 117, no. 17, May 2015.DOI
  60. [60]Y. Xu, G. Yang, D. Chu, and H. Zhai, “Magnetic anisotropy of bam ferrites,” Journal of Magnetism and Magnetic Materials, vol. 31, pp. 815–816, Feb. 1983.DOI
  61. [61]C. Pfeiffer and A. Grbic, “Metamaterial Huygens’ surfaces: Tailoring wave fronts with reflectionless sheets,” Phys. Rev. Lett., vol. 110, no. 19, p. 197401, May 2013.pubmed.ncbi.nlm.nih.gov/23705738
  62. [62]P. Nayeri, A. Z. Elsherbeni, and F. Yang, “Radiation analysis approaches for reflectarray antennas [antenna designer’s notebook],” IEEE Antennas Propag. Mag., vol. 55, no. 1, pp. 127–134, Feb. 2013.DOI
  63. [63]K. N. Rozanov, “Ultimate thickness to bandwidth ratio of radar absorbers,” IEEE Trans. Antennas Propag., vol. 48, no. 8, pp. 1230–1234, Aug. 2000.DOI
  64. [64]V. Asadchy, A. Díaz-Rubio, S. Tcetkoveta, D.-H. Kwon, A. Elsakka, M. Albooyeh, and S. Tretyakov, “Flat engineered multichannel reflectors,” Phys. Rev. X, vol. 7, no. 3, p. 031046, Sep. 2017.
  65. [65]F. Mesa, M. Garcia-Vigueras, F. Medina, R. Rodriguez-Berral, and J. R. Mosig, “Circuit-model analysis of frequency selective surfaces with scatterers of arbitrary geometry,” IEEE Antennas Wirel. Propag. Lett., vol. 14, pp. 135–138, 2014.DOI
  66. [66]S. R. Rengarajan, “Choice of basis functions for accurate characterization of infinite array of microstrip reflectarray elements,” IEEE Antennas Wirel. Propag. Lett., vol. 4, pp. 47–50, Jun. 2005.DOI

Paper details

vlnc:W_9au6d8cc
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents