betaFeedback

WorksPhysics and Astronomy

Recirculating Light Phase Modulator

Abstract

High efficiency and a compact footprint are desired properties for electro-optic modulators. In this paper, we propose, theoretically investigate and experimentally demonstrate a recirculating phase modulator, which increases the modulation efficiency by modulating the optical field several times in a non-resonant waveguide structure. The 'recycling' of light is achieved by looping the optical path that exits the phase modulator back and coupling it to a higher order waveguide mode, which then repeats its passage through the phase modulator. By looping the light back twice, we were able to demonstrate a recirculating phase modulator that requires nine times lower power to generate the same modulation index of a single pass phase modulator. This approach of modulation efficiency enhancement is promising for the design of advanced tunable electro optical frequency comb generators and other electro-optical devices with defined operational frequency bandwidths.

Introduction

Optical modulators are a vital component in communication systems [1] and microwave photonic devices [2, 3, 4, 5] as they provide the means to translate high speed electrical signals into the optical domain, where they can be further processed or propagate over kilometer length scales in optical fibres while experiencing minimal losses. Modulators can also be used for achieving desired on-chip functionalities, such as non-reciprocal devices [6]. While many optical modulators have been demonstrated using materials, such as silicon [5], indium phosphide [7], 2D materials [8] and polymers [9], arguably one of the most attractive platforms used for electro-optical functionalities is lithium niobate, owing to its low optical losses and high-speed modulation capacity [1].

Lithium niobate modulators have been commercially available for several decades and have been crucial in the success of optical fibre communications that underpin the internet [1]. Traditional lithium niobate devices use titanium indiffused waveguides, however a new generation of thin film silicon and indium phosphide integrated photonics has emerged offering improved drive voltage, compactness and the potential for system integration [1]. More recently, a similar revolution has taken place in the field of lithium niobate photonics with the emergence of the thin-film lithium niobate waveguide platform offering high efficiencies for electro-optic interaction, and nonlinear optical processes due to the strong modal confinement [10, 11, 12]. Nevertheless, there are design choices that need to be considered for efficient modulators in this platform such as the trade-off between the length and bandwidth of modulators [13] or the trade-off for the closeness of the electrode to the waveguide [14] and microwave losses of the electrodes [12]. Optical structures have also been investigated to improve modulation efficiency. For example loop mirrors [15], and Fabry–Perot cavities [16] have been demonstrated to increase the electro-optical interaction length. Recently, a promising way to increase the interaction length between a waveguide and a thermal heating element was demonstrated, providing an enhanced efficiency for tuning the phase of light by ‘recycling’ or recirculating it serval times through the same multimode waveguide, achieved by looping the light back and coupling it to the multimode waveguide using mode multiplexers [17].

In this contribution, we investigate if a conceptually similar light recirculation approach can be used for high-speed electro-optical modulators and how this concept can help to increase the efficiency of phase modulators. We experimentally demonstrate that the recirculating phase modulator increases the modulation efficiency with the number of recirculations. This enabled us to reduce the power of the microwave signal by a factor of 9 when the light passed 3 times through the phase modulator, when compared to a standard single pass phase modulator with the same electrode dimensions to achieve the same modulation depth.

Device Concept

The efficiency of an electro-optic device is directly related to the interaction length between the electrode and the electro-optic waveguide. One option is to make this interaction region as long as possible. We explore an alternative where light is recirculated several times through a phase modulator to improve the modulation efficiency. This is fulfilled by looping the light through different orthogonal modes in a multimode waveguide and applying microwave modulation simultaneously to all the different copropagating modes. Figure 1(a) illustrates the proposed recirculating modulator with two light recycling loops that is described as a case-in-point in detail as follows.

Image not extracted

Figure 1. (a) Schematic of a recirculating phase modulator; (b) Simulated mode multiplexer for coupling the TE0TE_0 to TE1TE_1 mode and coupling the TE0TE_0 to TE2TE_2 mode; (c) Cross-section of the multimode phase modulator electrode region; (d) Normalized optical field plots for the TE0TE_0, TE1TE_1 and TE2TE_2 modes.

In the proposed recirculating modulator, the light is coupled into a single mode waveguide in the form of the TE0 mode on the left side. It passes through two tapers that increase the waveguide width, making it multimode such that it supports TE0 and TE1 modes after the first taper and TE0, TE1 and TE2 modes after the second taper. The optical field intensity plots of modes supported in the waveguide after the second taper are illustrated in in Figure 1(d). After passing through the two tapers, the input optical power remains predominantly in the TE0 mode, which gets modulated by the microwave signal applied to the travelling wave electrodes, similar to a conventional phase modulator. A schematic cross-section of a modulator in the SiN loaded thin-film lithium niobate on insulator platform is shown in Figure 1(c). Afterwards, the multimode waveguide is tapered down in two stages back to the width of a single mode waveguide, which is then looped back to the input side, where it is coupled as the TE1 mode to the multimode waveguide, using mode multiplexers described in our previous work [18]. The TE1 mode passes again through the same traveling wave electrodes, experiencing a second modulation. Subsequently, the TE1 mode is coupled to a single TE0 mode waveguide using a mode multiplexer. The single mode waveguide is looped back again, where it is coupled as a TE2 mode to the multimode waveguide. The TE2 mode is then modulated again before it is coupled out as a TE0 mode to a single mode output waveguide. FDTD simulated operation of the TE0-TE1 and TE0-TE2 mode converters is shown in Figure 1(b) [18]. In principle the number of loops can be increased arbitrarily, but it comes at a cost of device footprint and might require wider electrode gaps, as the width of the multimode waveguides needs to increase to accommodate the additional higher order modes.

Theoretical Analysis

In this section, we have a closer look at the recirculating modulator operation and what considerations need to be taken into account to achieve an increased modulation efficiency. When a sinusoidal signal V(t)=Asin⁡(ωst)V(t) = A\sin(\omega_s t) is applied to a single pass phase modulator, the output optical field from the device can be expressed as:

Eout=EoeiωcteiRsin⁡ωst=Eoeiωct∑n=−∞+∞Jn(R)einωst(1)E_{\mathrm{out}} = E_o e^{i\omega_c t}e^{iR\sin\omega_s t} = E_o e^{i\omega_c t}\sum_{n=-\infty}^{+\infty} J_n(R)e^{in\omega_s t} \tag*{(1)}

where EoE_o and ωc\omega_c are the amplitude and angular frequency of the optical carrier; ωs\omega_s is the angular frequency of the radio frequency (RF) modulating signal, RR is the modulation index, which is equal to πA/Vπ\pi A/V_\pi, where AA is the amplitude of microwave signal and VπV_\pi is the voltage required to shift the phase of the carrier by π\pi, and JnJ_n is the Bessel function of the first kind. In the case of a recirculating modulator, as introduced in Figure 1(a), the light is modulated multiple times, which for NN recirculations can be expressed as:

Eout=EoeiωcteiR0sin⁡ωsteiR1sin⁡ωs(t−ΔT1)eiR2sin⁡ωs(t−ΔT2)…eiRNsin⁡ωs(t−ΔTN)(2)E_{\mathrm{out}} = E_o e^{i\omega_c t}e^{iR_0\sin\omega_s t}e^{iR_1\sin\omega_s(t-\Delta T_1)}e^{iR_2\sin\omega_s(t-\Delta T_2)} \ldots e^{iR_N\sin\omega_s(t-\Delta T_N)} \tag*{(2)}

where RjR_j (j=0,1,2,…Nj = 0, 1, 2, \ldots N) is the modulation index of the jjth recirculation and ΔTj\Delta T_j (j=1,2,…Nj = 1, 2, \ldots N) is the loop transit time for light to re-enter the modulator, which is effectively the time delay between two different modes be modulated by the RF electrode. The loop transit time is given by ΔTj=ΔLj/vg\Delta T_j = \Delta L_j/v_g, where ΔLj\Delta L_j is the length of loop jj and vgv_g is the group velocity of the fundamental mode TE0TE_0 in the loop waveguides. If one assumes that the modulation index is the same for all modes, equation 2 can be written as:

Eout=EoeiωcteiR∗κ∗sin⁡(ωst−φ)(3)E_{\mathrm{out}} = E_o e^{i\omega_c t}e^{iR\ast\kappa\ast\sin(\omega_s t-\varphi)} \tag*{(3)}

where φ=arctan⁡sin⁡ωsΔT1+sin⁡ωsΔT2+⋯+sin⁡ωsΔTn1+cos⁡ωsΔT1+cos⁡ωsΔT2+⋯+cos⁡ωsΔTn\varphi= \arctan\frac{\sin\omega_s \Delta T_1+\sin\omega_s \Delta T_2+\cdots+\sin\omega_s \Delta T_n}{1+\cos\omega_s \Delta T_1+\cos\omega_s \Delta T_2+\cdots+\cos\omega_s \Delta T_n} and the κ\kappa is the enhancement factor of the recirculating modulator. In the case of NNth recirculation, the enhancement factor can be expressed as:

κ=(1+cos⁡ωsΔT1+cos⁡ωsΔT2+⋯+cos⁡ωsΔTN)2+(sin⁡ωsΔT1+sin⁡ωsΔT2+⋯+sin⁡ωsΔTN)2(4)\kappa= \sqrt{\left(1+\cos\omega_s \Delta T_1+\cos\omega_s \Delta T_2+\cdots+\cos\omega_s \Delta T_N\right)^2+\left(\sin\omega_s \Delta T_1+\sin\omega_s \Delta T_2+\cdots+\sin\omega_s \Delta T_N\right)^2} \tag*{(4)}

Then, expanding equation 3 by Bessel functions of the first kind, the output signal can be described as:

Eout=Eoeiωct∗∑n=−∞+∞Jn(R∗κ)∗ein(ωst−φ)(5)E_{\mathrm{out}}=E_o e^{i\omega_c t} * \sum_{n=-\infty}^{+\infty} J_n(R * \kappa) * e^{in(\omega_s t-\varphi)} \tag*{(5)}

As one can see from Eq. (4) and Eq. (5), the output signal is strongly dependent on the enhancement factor, which is determined by modulation frequency ωs\omega_s and the delay time ΔTj\Delta T_j for each recirculating loop. Maximum enhancement factor can be achieved when ΔTj=mπ/ωs\Delta T_j=m\pi/\omega_s, where mm is an integer. For NN recirculations, the maximum enhancement factor is equal to N+1N+1.

Device Design

For investigating the recirculating modulator, we chose the SiN loaded thin-film lithium niobate on insulator platform, see Figure 1(a) and our pervious works [18, 19], with a 0.3 μ\mum thick lithium niobate film and a 0.3 μ\mum thick silicon nitride thickness. The waveguide widths needed to support the three different waveguide modes were 1.2, 2.8 and 4.5 μ\mum in accordance with the mode multiplexers in [18]. For the travelling wave electrode, we chose an electrode separation of 9.5 μ\mum and a gold metal thickness of 0.5 μ\mum. The VπV_\pi of the TE0, TE1 and TE2 modes was calculated to be 7.38, 7.35 and 7.52 V·cm.

In designing prototype recirculating phase modulators we chose a 25 GHz operation frequency. When considering the group index of the TE0 in in loop waveguides ng=2.23n_g=2.23, calculations show that for the device to operate at its highest enhancement factor the waveguide lengths for TE0 and TE1 loops have to respectively be 21.5 mm and 16.1 mm. To confirm this, we simulated the enhancement factor as a function of the modulation frequency, which is shown in Figure 2. One can see that the conventional single-pass phase modulator has an enhancement factor of 1 for all frequencies (assuming ideal operation). Conversely, a single loop recirculating modulator has a periodic response, reaching an enhancement factor of κ∼2\kappa\sim2 at 0, 6.3, 12.5, 18.8, 25, 31.3 and 37.5 GHz, while the dual loop recirculating modulator reaches an enhancement factor of κ∼3\kappa\sim3 for 0 and 25 GHz. This shows that we should expect an increase of the enhancement factor to 3 when looping the light back twice and operating at 25 GHz with delay lengths of 21.5 mm and 16.1 mm for the two loops.

Enhancement factors as a function of modulation frequency for single- and dual-loop recirculating phase modulators

Figure 2. Enhancement factors as a function of the modulation frequency for single and a dual loop recirculating phase modulators A typical single-pass phase modulator exhibits a frequency independent baseline κ=1\kappa= 1 enhancement factor.

Experimental Results

To prove the device performance, we fabricated the designed 25 GHz operation frequency recirculating modulator devices with one and two loops and benchmarked them against a traditional single-pass phase modulator. Fabrication was performed following the steps outlined in our prior work [18]. In brief, optical waveguiding in thin-film lithium niobate (see Figure 3(b)) is established by depositing a SiN loading layer by means of reactive sputtering [20], followed by patterning this SiN film using electron beam lithography and reactive ion etching. Gold electrodes (Figure 3(c)) comprising the electrooptical modulator section were formed using laser lithography patterning with a subsequent physical vapor deposition and lift-off process. The fabricated device with two recirculation loops is shown in Figure 3(a). The on-chip footprint of this device is 10.85 mm ×\times 5.61 mm and the active modulation section takes up 62% of total device length.

Fabricated recirculating phase modulator device and component micrographs

Figure 3. (a) Optical microscope image of recirculating phase modulator device with two loops; (b) Scanning electron micrograph of a fabricated single mode waveguide; (c) shows the traveling wave electrode alignment to the multimode waveguide; (d) shows the fabricated mode multiplexer to couple the TE2\mathrm{TE}_{2} to a TE0\mathrm{TE}_{0} mode and (e) is the mode multiplexer for coupling the TE1\mathrm{TE}_{1} mode to a TE0\mathrm{TE}_{0} mode.

To characterize the performance of the recirculating modulators, we couple 1550 nm light into the devices and applied an amplified 25 GHz microwave signal from an Anritsu MG3694A frequency synthesizer to the traveling wave electrodes and measured the resulting spectra with a Finisar WaveAnalyzer 1500S High-Resolution Optical Spectrum Analyzer. The output of the electrodes was terminated with 50 Ohm impedance matching terminators. Figure 4(a-Figure 4c) shows the measured spectra when a 25 dBm RF power is applied to a typical single-pass phase modulator as well as recirculating phase modulators with one and two loops, respectively. These modulators have the same electrode length, gap, and thickness. One can see that the overall optical power levels for the graphs are slightly different, which is most likely caused by fabrication errors as well as increased losses for the recirculating modulators with two loops, due to the increased waveguide length and additional mode multiplexing structures. One can also see that a recirculating modulator can generate more sidebands compared to a conventional phase modulator. To estimate the modulation index, we fitted the power of sideband power using Eq. (1) and found that the modulation index approximately doubled for the single loop recirculating modulator and tripled for the two loop recirculating modulator (see black dots in Figure 4(a-Figure 4c)), when compared to a single-pass phase modulator. These results matched well with our prediction of how the enhancement factor scales with the number of loops, as shown in Figure 2.

Image not extracted

Figure 4. Measured spectra for (a) single mode phase modulator, (b) single loop and (c) two loop recirculating modulators when 25dBm RF power is applied.

Next, we characterized the modulation efficiency of the different modulators by adjusting the applied RF power so that the spectra exhibit the same modulation index (same power distribution of the sidebands) as compared to the single-pass phase modulator. The results are shown in Figure 5 (a-Figure 5c), which show that the single-pass phase modulator as well as the single loop and dual loop recirculating phase modulators exhibit the same modulation index, while the applied microwave power decreases from 28 dBm, to 22.1 dBm and 17.7 dBm, respectively. This corresponds well to the theoretical prediction of the RF power reduction for a single loop recirculation, which is 222^{2} (6 dB), and for a dual loop recirculation is 323^{2} (9.5 dB). This indicates that the dual loop recirculating phase modulator requires approximately one order of magnitude less RF power to achieve the same modulation index, increasing the modulation efficiency significantly.

Equivalent spectra generated by single mode phase modulator, one loop, and two loop recirculating phase modulators

Figure 5. Equivalent spectra generated by (a) single mode phase modulator (28 dBm RF power), (b) one loop (22.1 dBm RF power), and (c) two loop recirculating phase modulators (17.7 dBm RF power).

To analyze the modulation efficiency, we measured the modulation index of the modulators for different RF powers. The results are presented in Figure 6. One can see that the modulation index has a near quadratic dependence on the RF power, which matches the RF power scaling with applied voltage. One can also observe how the modulation index for the recirculating modulators increases by a factor of ~2 for a single loop recirculating modulator and ~3 for a dual loop recirculating modulator compared to the single pass phase modulator with an equivalent electrode configuration. This demonstrates that light recirculation in modulators can notably improve their modulation efficiency.

Modulation index of a conventional phase modulator and the recirculating modulators with one and two loops

Figure 6. Modulation index of a conventional phase modulator and the recirculating modulators with one and two loops as a function of the applied RF power.

Discussion

Experimental demonstration of the recirculating modulator has shown that increasing the number of loops does indeed increase the modulation efficiency. Although this is highly attractive, one also needs to consider trade-offs that come with such a design. For example, one should be aware that the operation bandwidth of the modulator is decreased and that adding more loops to the recirculating phase modulators may result in higher optical losses. There is also a practical limitation on the loop number scalability, as higher order multimode waveguides will be required, causing the waveguide modes to be closer in their effective indices, which can lead to enhanced cross talk between the modes. Furthermore, a wider multimode waveguide will increase the separation of electrodes, resulting in a higher VπV_{\pi} of modulators. Nevertheless, we believe that the investigated recirculating phase modulators are highly attractive for applications for the generation of electro optical frequency combs [21, 22], where one can apply a known and constant RF signal. The advantage of the recirculating modulator is that RF losses of the electrodes are less of a concern compared to high efficiency modulators that rely on long electrodes. It may also become possible to consider such devices for optical computational tasks, as the looping back through the same modulator offers the imprinting of different electrical signals in time onto the optical domain [23].

Conclusion

In this work, we present a new recirculating phase modulator concept, explore its properties through numerical simulations and experimentally validate the performance of a prototype device fabricated on the thin-film lithium niobate on insulator platform. The recirculating modulators with two light recycling loops exhibit an approximately threefold increase in modulation efficiency, enabling a reduction of the microwave power required for achieving the same modulation index by approximately one order of magnitude. We also provide the numerical expression of enhancement factor for NNth recirculation case, which provides the possibility for further improvement in the future. Moreover, we believe such modulators pave the way to reduce the power required for electro-optical frequency comb generation and for executing optical computation tasks.

Funding

The material is based on work supported by the Australian Research Council (ARC) under award ARC DP190102773.

Data availability

The data that support the findings of this study are available from the corresponding author upon reasonable request.

References

  1. [1]E. L. Wooten et al., "A review of lithium niobate modulators for fiber-optic communications," IEEE Journal of selected topics in Quantum Electronics, vol. 6, no. 1, pp. 69-82, 2000.DOI
  2. [2]D. Marpaung, J. Yao, and J. Capmany, "Integrated microwave photonics," Nature photonics, vol. 13, no. 2, pp. 80-90, 2019.
  3. [3]P. Ghelfi et al., "A fully photonics-based coherent radar system," Nature, vol. 507, no. 7492, pp. 341-345, 2014.DOI
  4. [4]T. M. Fortier et al., "Generation of ultrastable microwaves via optical frequency division," Nature Photonics, vol. 5, no. 7, pp. 425-429, 2011.DOI
  5. [5]G. T. Reed, G. Mashanovich, F. Y. Gardes, and D. Thomson, "Silicon optical modulators," Nature photonics, vol. 4, no. 8, pp. 518-526, 2010.
  6. [6]L. D. Tzuang, K. Fang, P. Nussenzveig, S. Fan, and M. Lipson, "Non-reciprocal phase shift induced by an effective magnetic flux for light," Nature photonics, vol. 8, no. 9, pp. 701-705, 2014.DOI
  7. [7]Y. Ogiso et al., "Over 67 GHz bandwidth and 1.5 V Vπ InP-based optical IQ modulator with nipn heterostructure," Journal of lightwave technology, vol. 35, no. 8, pp. 1450-1455, 2017.DOI
  8. [8]S. Yu, X. Wu, Y. Wang, X. Guo, and L. Tong, "2D materials for optical modulation: challenges and opportunities," Advanced Materials, vol. 29, no. 14, p. 1606128, 2017.DOI
  9. [9]M. Lee et al., "Broadband modulation of light by using an electro-optic polymer," Science, vol. 298, no. 5597, pp. 1401-1403, 2002.pubmed.ncbi.nlm.nih.gov/12434054
  10. [10]G. Poberaj, H. Hu, W. Sohler, and P. Guenter, "Lithium niobate on insulator (LNOI) for micro-photonic devices," Laser & photonics reviews, vol. 6, no. 4, pp. 488-503, 2012.DOI
  11. [11]A. Boes, B. Corcoran, L. Chang, J. Bowers, and A. Mitchell, "Status and potential of lithium niobate on insulator (LNOI) for photonic integrated circuits," Laser & Photonics Reviews, vol. 12, no. 4, p. 1700256, 2018.DOI
  12. [12]M. Zhang, C. Wang, P. Kharel, D. Zhu, and M. Lončar, "Integrated lithium niobate electro-optic modulators: when performance meets scalability," Optica, vol. 8, no. 5, pp. 652-667, 2021.DOI
  13. [13]A. N. R. Ahmed, S. Nelan, S. Shi, P. Yao, A. Mercante, and D. W. Prather, "Subvolt electro-optical modulator on thin-film lithium niobate and silicon nitride hybrid platform," Optics letters, vol. 45, no. 5, pp. 1112-1115, 2020.DOI
  14. [14]M. Jin, J. Chen, Y. Sua, P. Kumar, and Y. Huang, "Efficient electro-optical modulation on thin-film lithium niobate," Optics Letters, vol. 46, no. 8, pp. 1884-1887, 2021.
  15. [15]J. Jian et al., "High modulation efficiency lithium niobate Michelson interferometer modulator," Optics Express, vol. 27, no. 13, pp. 18731-18739, 2019.DOI
  16. [16]B. Pan et al., "Compact electro-optic modulator on lithium niobate," Photonics Research, vol. 10, no. 3, pp. 697-702, 2022.DOI
  17. [17]Y.-C. Chang, S. P. Roberts, B. Stern, and M. Lipson, "Resonance-free light recycling," arXiv preprint arXiv:1710.02891, 2017.arxiv.org/abs/1710.02891
  18. [18]X. Han et al., "Mode and Polarization-Division Multiplexing Based on Silicon Nitride Loaded Lithium Niobate on Insulator Platform," Laser & Photonics Reviews, vol. 16, no. 1, p. 2100529, 2022.DOI
  19. [19]P. Zhang et al., "High-speed electro-optic modulator based on silicon nitride loaded lithium niobate on an insulator platform," Optics letters, vol. 46, no. 23, pp. 5986-5989, 2021.DOI
  20. [20]A. Frigg et al., "Low loss CMOS-compatible silicon nitride photonics utilizing reactive sputtered thin films," Optics express, vol. 27, no. 26, pp. 37795-37805, 2019.DOI
  21. [21]V. Torres-Company and A. M. Weiner, "Optical frequency comb technology for ultra-broadband radio-frequency photonics," Laser & Photonics Reviews, vol. 8, no. 3, pp. 368-393, 2014.
  22. [22]A. J. Metcalf, V. Torres-Company, D. E. Leaird, and A. M. Weiner, "High-power broadly tunable electooptic frequency comb generator," IEEE Journal of Selected Topics in Quantum Electronics, vol. 19, no. 6, pp. 231-236, 2013.DOI
  23. [23]C. Qiu, H. Xiao, L. Wang, and Y. Tian, "Recent advances in integrated optical directed logic operations for high performance optical computing: a review," Frontiers of Optoelectronics, vol. 15, no. 1, pp. 1-17, 2022.DOI

Paper details

vlnc:W_ajgj3u8d
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents