betaFeedback

WorksPhysics and Astronomy

On force balance in Brinkman fluids under confinement

Abstract

A point force acting on a Brinkman fluid in confinement is always counterbalanced by the force on the porous medium, the force on the walls and the stress at open boundaries. We discuss the distribution of those forces in different geometries: a long pipe, a medium with a single no-slip planar boundary, a porous sphere with an open boundary and a porous sphere with a no-slip wall. We determine the forces using the Lorentz reciprocal theorem and additionally validate the results with explicit analytical flow solutions. We discuss the relevance of our findings for cellular processes such as cytoplasmic streaming and centrosome positioning.

Introduction

In the absence of of inertia, fluids at low Reynolds numbers are always in a state of force balance: the sum of volume forces, surface forces and the stress integrated over a closed surface always equals zero. In confined geometries, the force balance can take a surprising form. A notable example is the flow due to a point force inside a long pipe with a no-slip boundary [1, 2]. The external force leads to a pressure difference between the two ends of the pipe (Figure 1a). Depending on the radial position of the point force, the pressure difference, multiplied by the cross-section area of the pipe, can exceed the original force by a factor of 2 [3, 4]. The remainder of the force is contributed by the force on the wall of the pipe, which changes its sign at a certain position of the applied force. A related result was found for a Stokeslet between two parallel plates [5].

Figure 1. Point force in a pipe. (a) Force balance: the external force FF is distributed to the force on the wall FWF_{\mathrm{W}} and the force due to pressure difference FP=πR2ΔpF_{\mathrm{P}} = \pi R^{2}\Delta p. The direction of the force on the walls changes with the radial position of the force. (b) Pressure driven flow through a pipe with a Brinkman fluid is used as an auxiliary problem when applying the reciprocal theorem. (c) Induced pressure difference as a function of the distance hh of the force from the tube’s axis, as given by Eq. (11). The dashed line represents the limit α→∞\alpha\to\infty. (d) Streamlines around a point force acting at the centre of the channel (h=0h = 0). At small values of αR\alpha R, the flow shows a series of viscous tubular eddies which disappear at around αR≈4.7\alpha R \approx4.7.

The Brinkman equation [6, 7]

η(Δv−α2v)−∇p+f=0(1)\eta(\Delta\mathbf{v} - \alpha^{2}\mathbf{v}) - \nabla p + \mathbf{f} = 0 \tag*{(1)}

along with the incompressibility condition ∇⋅v=0\nabla\cdot\mathbf{v} = 0, describes the flow of a fluid through a porous medium. Here, η\eta is the dynamic viscosity of the Newtonian fluid and α2\alpha^{2} represents the impermeability of the porous medium, with dimensions of (length)−2^{-2}. The density of external forces acting on the fluid is denoted by f\mathbf{f}. Equivalently, it can also be expressed as a continuity equation for the stress tensor σ=−pI+η(∇v+(∇v)T)\boldsymbol{\sigma} = -p\mathbf{I} + \eta(\nabla\mathbf{v} + (\nabla\mathbf{v})^{\mathsf{T}}):

∇⋅σ−ηα2v+f=0(2)\nabla\cdot\boldsymbol{\sigma} - \eta\alpha^{2}\mathbf{v} + \mathbf{f} = 0 \tag*{(2)}

The force balance therefore needs to take into account the momentum exchange between the fluid and the medium. The force balance equation on a volume of fluid V\mathcal{V} is obtained by applying the divergence theorem to Eq. (2) and reads

∮∂Vσ⋅n dS+∫V(f−ηα2v) dV=0(3)\oint_{\partial\mathcal{V}} \boldsymbol{\sigma} \cdot\mathbf{n}\,\mathrm{d}S + \int_{\mathcal{V}}(\mathbf{f} - \eta\alpha^{2}\mathbf{v})\,\mathrm{d}V = 0 \tag*{(3)}

with n\mathbf{n} as a unit normal vector pointing outward. In this paper, we discuss the cumulative force balance in Brinkman flows under different types of confinement. We discuss the application of the results to different kinds of cytoplasmic flows.

Examples of force balance

The discussion of specific cases follows the level of confinement. We begin with the flow induced by a point force in an infinite pipe, akin to the solution by Liron and Shahar [2], but with a Brinkman medium instead. We continue with the point force in the presence of a wall, extending the classical solution of Blake [8], with a force balance specifically discussed by Škultéty and Morozov [5]. Finally, we proceed with a force inside a porous sphere with open boundaries (i.e., surrounded by free fluid), as well as no-slip spherical confinement. All solutions are determined by the application of the Lorentz reciprocal theorem, which greatly simplifies the calculation of cumulative forces. We also validate and illustrate the results with explicit exact solutions for some cases.

Material force in confined flows

We begin with a note on the material force, i.e., the force the fluid exerts on the porous medium,

FM=∫Vηα2v dV(4)\mathbf{F}_{\mathrm{M}} = \int_{\mathcal{V}} \eta\alpha^{2}\mathbf{v}\,\mathrm{d}V \tag*{(4)}

in a confined flow with zero normal velocity, v⋅n=0\mathbf{v} \cdot\mathbf{n} = 0 at the outer boundary ∂V\partial\mathcal{V}. By applying the divergence theorem to the quantity (e⋅x)v(\mathbf{e} \cdot\mathbf{x})\mathbf{v} with an arbitrary unit vector e\mathbf{e} and noting that ∇⋅((e⋅x)v)=e⋅v\nabla\cdot((\mathbf{e} \cdot\mathbf{x})\mathbf{v}) = \mathbf{e} \cdot\mathbf{v} for ∇⋅v=0\nabla\cdot\mathbf{v} = 0, we obtain

e⋅∫Vv dV=∮∂V(e⋅x)v⋅n dS=0.(5)\mathbf{e} \cdot\int_{\mathcal{V}} \mathbf{v}\,\mathrm{d}V = \oint_{\partial\mathcal{V}} (\mathbf{e} \cdot\mathbf{x})\mathbf{v} \cdot\mathbf{n}\,\mathrm{d}S = 0. \tag*{(5)}

Because the equality holds for any e\mathbf{e}, it follows that

∫Vv dV=0(6)\int_{\mathcal{V}} \mathbf{v}\,\mathrm{d}V = 0 \tag*{(6)}

for any confined flow, and therefore the total force acting on the porous material vanishes, FM=0\mathbf{F}_{\mathrm{M}} = 0.

Point force in a pipe

The first example consists of a point force FF inside an infinitely long pipe with radius RR that is filled with a porous medium (Figure 1a). The force is acting in axial direction at distance hh from the axis of the pipe. We disregard any radial components of the force FF, because it is clear from symmetry arguments that they will act on the wall of the tube alone, without contributing to the long-range pressure difference.

In order to apply the Lorentz reciprocal theorem, we first solve the auxiliary problem, which is a pressure driven flow through a pipe containing a Brinkman medium (Figure 1(b)). The fluid is therefore described by the Brinkman equation (1), along with the condition of incompressibility ∇⋅v^=0\nabla\cdot\hat{\boldsymbol{v}} = 0 (the hatted quantities are used to distinguish the auxiliary from the main problem). The pipe is oriented along the zz-axis. At the walls the no-slip condition v^=0\hat{\boldsymbol{v}} = 0 applies and the whole tube is subject to a negative pressure gradient, G=−dp^/dz>0G = -\mathrm{d}\hat{p}/\mathrm{d}z > 0. We write the Brinkman equation in cylindrical coordinates

1ρddρ(ρdv^zdρ)−α2v^z+Gη=0.(7)\frac{1}{\rho}\frac{\mathrm{d}}{\mathrm{d}\rho}\left(\rho\frac{\mathrm{d}\hat{v}_z}{\mathrm{d}\rho}\right)-\alpha^2\hat{v}_z+\frac{G}{\eta}=0. \tag*{(7)}

The boundary condition states v^z(ρ=R)=0\hat{v}_z(\rho=R)=0. The solution for the axial velocity is

v^z=Gα2η(1−I0(αρ)I0(αR)),(8)\hat{v}_z=\frac{G}{\alpha^2\eta}\left(1-\frac{I_0(\alpha\rho)}{I_0(\alpha R)}\right), \tag*{(8)}

with In(x)I_n(x) denoting the nnth-order modified Bessel function of the first kind [9]. The volume flow rate through the pipe is

Q^=∫0Rv^z(ρ) 2πρ dρ=πR2Gα2ηI2(αR)I0(αR).(9)\hat{Q}=\int_0^R\hat{v}_z(\rho)\,2\pi\rho\,\mathrm{d}\rho=\frac{\pi R^2G}{\alpha^2\eta}\frac{I_2(\alpha R)}{I_0(\alpha R)}. \tag*{(9)}

In the limit α→0\alpha\to0, corresponding to the Stokes flow regime, we can use the series expansion I0(x)=1+x2/4+O(x4)I_0(x)=1+x^2/4+O(x^4), I2(x)=x2/8+O(x4)I_2(x)=x^2/8+O(x^4) and recover the classical parabolic velocity profile of the Hagen–Poiseuille flow with v^z=G(R2−r2)/(4η)\hat{v}_z=G(R^2-r^2)/(4\eta) and Q^=πR4G/(8η)\hat{Q}=\pi R^4G/(8\eta).

We now apply the Lorentz reciprocal theorem (derived for Brinkman fluids in Appendix § 2.0.1) with the pressure driven flow as auxiliary problem. The reciprocal theorem states

∫∂Vv⋅σ^⋅n dS+∫Vv⋅f^ dV=∫∂Vv^⋅σ⋅n dS+∫Vv^⋅f dV.(10)\int_{\partial V}\boldsymbol{v}\cdot\hat{\boldsymbol{\sigma}}\cdot\boldsymbol{n}\,\mathrm{d}S+\int_V\boldsymbol{v}\cdot\hat{\boldsymbol{f}}\,\mathrm{d}V=\int_{\partial V}\hat{\boldsymbol{v}}\cdot\boldsymbol{\sigma}\cdot\boldsymbol{n}\,\mathrm{d}S+\int_V\hat{\boldsymbol{v}}\cdot\boldsymbol{f}\,\mathrm{d}V. \tag*{(10)}

The integration surface ∂V\partial V runs along the wall of the pipe and is closed at z=±∞z=\pm\infty (Figure 1b). Because both velocities are zero at the walls, all surface integrals vanish there. At the ends of the pipe, the left surface integral vanishes because v→0\boldsymbol{v}\to0, but the right gives −Q^Δp-\hat{Q}\Delta p, where Δp=p(z→∞)−p(z→−∞)\Delta p=p(z\to\infty)-p(z\to-\infty) is the pressure difference buildup in the main problem. We know that the pressure at both ends needs to be constant across the tube because of the vanishing velocity. The left volume integral also vanishes because f^=0\hat{\boldsymbol{f}}=0 by definition. This leads to a relationship for the pressure difference

Δp=Fv^z(h)Q^=FπR2I0(αR)−I0(αh)I2(αR).(11)\Delta p=\frac{F\hat{v}_z(h)}{\hat{Q}}=\frac{F}{\pi R^2}\frac{I_0(\alpha R)-I_0(\alpha h)}{I_2(\alpha R)}. \tag*{(11)}

In the limit α→0\alpha\to0, the relation simplifies to Δp=2F(1−h2/R2)/(πR2)\Delta p=2F(1-h^2/R^2)/(\pi R^2), in agreement with the exact flow solution [1, 2] and also the lubrication approximation by [10]. Note that the reciprocal theorem allowed us to obtain this result with a much shorter and simpler derivation compared to the explicit solutions in the references above.

The resulting radial dependence is shown in Figure 1(c). Whereas the Brinkman medium always reduces the pressure if the force is near the axis of the channel, the opposite is the case in the proximity of the wall, where an increased value of α\alpha leads to a higher Δp\Delta p.

Because of the rapid fall-off of the velocity with the distance along the pipe, the pipe can be effectively seen as confined, and the force on the porous material is zero. Force balance therefore implies that the force exerted by the fluid on the walls is

FW=F−πR2Δp=F(1−I0(αR)−I0(αh)I2(αR)).(12)F_{\mathrm{W}}=F-\pi R^2\Delta p=F\left(1-\frac{I_0(\alpha R)-I_0(\alpha h)}{I_2(\alpha R)}\right). \tag*{(12)}

As in the Stokes fluid, the force on the wall changes direction: it is parallel to FF when the external force acts close to the wall, but antiparallel when it is in the centre of the pipe.

Although the we only consider an infinitely long tube here, the solution for a length that is finite, but still much larger than the diameter, can easily be obtained by superposition. Another possible extension is the mobility matrix of two particles in the pipe. For Stokes fluids, it has been shown that the off-diagonal elements expressing hydrodynamic interactions depend on the length of the tube, but not on the distance between the particles [11].

Point force in the proximity of a plane

We now study the force exerted on an infinite plane by a force acting parallel to it at some distance hh (Figure 2a). The auxiliary problem consists of the plane itself moving tangentially with velocity V^\hat{\mathbf V} while the porous medium itself does not move (Figure 2b). The Brinkman equation for the auxiliary problem reduces to

Figure 2. (a) Point force F\mathbf F on the Brinkman fluid in the presence of a no-slip wall. The force is distributed over the force on the wall FW\mathbf F_{\mathrm W}, the force on the porous medium FM\mathbf F_{\mathrm M} and force due to the pressure difference. (b) In the auxiliary problem, the wall itself is moving with the velocity V^\hat{\mathbf V}.

(∂z2−α2)v^=0,(13)(\partial_z^2-\alpha^2)\hat{\mathbf v}=0, \tag*{(13)}

with the boundary condition v^=V^\hat{\mathbf v}=\hat{\mathbf V} at z=0z=0 and is solved as

v^=V^e−αz.(14)\hat{\mathbf v}=\hat{\mathbf V}e^{-\alpha z}. \tag*{(14)}

We now apply the Lorentz reciprocal theorem to the half-space containing the Brinkman fluid. The integration surface contains the plane and the upper hemisphere at infinite distance (dashed line in Figure 2b). Because both v^\hat{\mathbf v} and v\mathbf v converge to 0 sufficiently fast at large distances, the surface integrals over the hemisphere vanish. The reciprocal theorem then states that

∫V^⋅σ⋅ez dS−v^⋅F=0(15)\int\hat{\mathbf V}\cdot\boldsymbol{\sigma}\cdot\mathbf e_z\,dS-\hat{\mathbf v}\cdot\mathbf F=0 \tag*{(15)}

leading to V^⋅FW=v^⋅F\hat{\mathbf V}\cdot\mathbf F_{\mathrm W}=\hat{\mathbf v}\cdot\mathbf F. The horizontal force exerted by the fluid on the plane is therefore

FW=Fe−αz.(16)\mathbf F_{\mathrm W}=\mathbf F e^{-\alpha z}. \tag*{(16)}

The long-range nature of the flow and pressure (calculated explicitly in Eq. (66)) has the consequence that the integral ∫pn dS\int p\mathbf n\,dS does not have a defined limit when the boundary is infinitely far from the force. Therefore, it is not possible to state which part of the force is carried by pressure and which part by the porous medium, unlike the force on the wall. However, the force due to the pressure vanishes in the Stokes limit α→0\alpha\to0, as already noted by Blake [8]. A related problem appears in a Stokes fluid between two plates, which becomes related to a 2D Brinkman fluid in the far-field regime. Although the pressure contribution to the horizontal force balance was determined by [5], we note that the exact result depends on the way how the integration area approaches an infinite plane and is therefore not uniquely defined.

Point force inside a sphere with open boundaries

In this section, we consider an external point force acting on the fluid inside a porous sphere, immersed in a Stokes fluid of the same viscosity (Figure 3a). The porous medium itself is fixed in the laboratory frame.

Figure 3. (a) The force F\mathbf{F} is acting axisymmetrically on the Brinkman fluid inside a porous sphere at a fixed position in laboratory frame and embedded in a Stokes fluid. (b) The same sphere, subject to an external flow with velocity V^\hat{\mathbf{V}}, is used as auxiliary problem. (c) The porous sphere is free to move, and subject to a pair of opposite forces, one acting on the Brinkman fluid and one on the sphere. (d) The velocity V′\mathbf{V}' of the sphere shown in panel (c) as a function of the force position. The horizontal dashed lines indicate the velocity of the porous sphere pulled by an external force of magnitude FF. (e,f) Flow in and around the fixed porous sphere for two positions of the external point force. (g) Flow in the auxiliary problem. All streamline plots are computed with the value αR=10\alpha R=10.

For the auxiliary problem (Figure 3b), we choose the same sphere in an external flow such that v^(r→∞)=V^\hat{\mathbf{v}}(r \to\infty)=\hat{\mathbf{V}}. A solution for the flow past a porous sphere can be found in [12]. The drag coefficient is

Γ=4πηR(αR)2ϕ(αR)ϕ(αR)+2,(17)\Gamma= 4\pi\eta R(\alpha R)^2\frac{\phi(\alpha R)}{\phi(\alpha R)+2}, \tag*{(17)}

where we introduced the function

ϕ(x)=3x2(1−tanh⁡xx),(18)\phi(x)=\frac{3}{x^2}\left(1-\frac{\tanh x}{x}\right), \tag*{(18)}

which takes values between 1 when x=0x=0 and 0 when x→∞x\to\infty. The radial flow velocity along the symmetry axis, at distance rr from the centre of the sphere, is [12]

v^=V^ϕ(αR)+2ϕ(αr)cosh⁡(αr)/cosh⁡(αR)ϕ(αR)+2.(19)\hat{\mathbf{v}}=\hat{\mathbf{V}}\frac{\phi(\alpha R)+2\phi(\alpha r)\cosh(\alpha r)/\cosh(\alpha R)}{\phi(\alpha R)+2}. \tag*{(19)}

An example of the complete flow profile is shown in Figure 3g.

For simplicity, we restrict ourselves the case where the external force is axisymmetric, acting radially with respect to the centre of the sphere. We apply the reciprocal theorem to the whole space, closed at infinity (Figure 3b). At the integration surface, we therefore have v→0\mathbf{v}\to0 and ∫σ⋅n dS=−F∞\int\boldsymbol{\sigma}\cdot\mathbf{n}\,\mathrm{d}S=-\mathbf{F}^{\infty}, the force transmitted to the fluid. The velocity of the auxiliary problem is v^=V^\hat{\mathbf{v}}=\hat{\mathbf{V}}. The reciprocal theorem then reads

F⋅v^(h)−F∞⋅V^=0.(20)\mathbf{F}\cdot\hat{\mathbf{v}}(h)-\mathbf{F}^{\infty}\cdot\hat{\mathbf{V}}=0. \tag*{(20)}

The resulting force is

F∞=Fϕ(αR)+2ϕ(αh)cosh⁡(αh)/cosh⁡(αR)ϕ(αR)+2.(21)F^{\infty}=F\frac{\phi(\alpha R)+2\phi(\alpha h)\cosh(\alpha h)/\cosh(\alpha R)}{\phi(\alpha R)+2}. \tag*{(21)}

Likewise, the force exerted on the porous sphere is

FM=F−F∞=2F1−ϕ(αh)cosh⁡(αh)/cosh⁡(αR)ϕ(αR)+2.(22)F_{\mathrm{M}}=F-F^{\infty}=2F\frac{1-\phi(\alpha h)\cosh(\alpha h)/\cosh(\alpha R)}{\phi(\alpha R)+2}. \tag*{(22)}

In the above calculation, the force is external in its nature and the porous sphere is fixed in space. A more interesting example, however, is the situation where the force acts between the porous medium and the fluid, i.e., if the force FF acts on the fluid and simultaneously the force −F-F on the medium (Figure 3(c)). This model can describe a motor protein pulling a vesicle through a dense filament network. For some continuous force distributions, a similar problem, albeit with a different boundary condition, has been solved by Kree and Zippelius [13]. We solve the problem for a point force in two steps: we initially keep the porous sphere fixed in space, and later determine its velocity under the force-free condition. For a clamped sphere, the total force on the medium is

FM′=−F+FM=−F∞.(23)F_{\mathrm{M}}^{\prime}=-F+F_{\mathrm{M}}=-F^{\infty}. \tag*{(23)}

If the sphere is free to move, such that the only forces acting on it are hydrodynamic forces and the reaction −F-F, its velocity will be

V′=FM′Γ=−F4πηR(αR)2(1+2ϕ(αh)cosh⁡(αh)ϕ(αR)cosh⁡(αR)).(24)V^{\prime}=\frac{F_{\mathrm{M}}^{\prime}}{\Gamma}=-\frac{F}{4\pi\eta R(\alpha R)^2}\left(1+2\frac{\phi(\alpha h)\cosh(\alpha h)}{\phi(\alpha R)\cosh(\alpha R)}\right). \tag*{(24)}

The velocity as a function of the position and the constant α\alpha is shown in Figure 3(d). The velocity always lies below what would be expected when the medium was pulled by an external force of magnitude −F-F. The velocity magnitude has a minimum at the centre of the sphere and increases weakly and monotonically with hh, attaining its maximum value at h=Rh=R. As αR\alpha R decreases, the velocities increase, where V′∼α−2V^{\prime}\sim\alpha^{-2} around α=0\alpha=0.

Point force inside a sphere with no-slip confinement

The final example also concerns a point force in a porous sphere, which is now subject to additional confinement by a spherical wall with no-slip conditions. The sphere tightly encloses the porous medium, such that the flow through the gap between them is negligible. At the same time, the gap is still wide enough that it allows free motion of the porous sphere at a given moment and that there are no direct mechanical forces across the gap (Figure 4(a)). The rationale behind this assumption is that over longer times, the sphere, representing for example a microtubule aster (see Discussion), is dynamic and grows to fill the widening gap on one side and retracts on the other [14, 15]. This growth and shrinkage take place through filament polymerisation and depolymerisation and therefore do not directly contribute to the force balance, but they maintain the system in a state where the assumption of a narrow gap remains valid.

Figure 4. (a) Point force acting on the fluid in a porous sphere, confined by a no-slip boundary. All the force is transmitted to the wall, FW=F\mathbf{F}_{\mathrm{W}}=\mathbf{F}. (b) A pair of forces acting between the fluid and the porous sphere. The sphere is enclosed by the no-slip boundary at close distance, but still free to move (with velocity V′\mathbf{V}'). (c,d) The flow velocity induced by a point force located at distance h/R=0h/R=0 and h/R=0.75h/R=0.75, both for αR=10\alpha R=10.

As with open boundaries, we first solve the problem for a point force and then for a pair of forces. Unlike in the previous cases, the force balance can be understood directly, without solving an auxiliary problem. For a point force in a fixed medium, it follows from considerations for confined spaces in Sec. II A that the total force on the medium vanishes, FM=0F_{\mathrm{M}}=0. Consequently, all the force is transmitted to the walls, so FW=FF_{\mathrm{W}}=F. The result holds for any kind of boundary condition (no-slip or slip), as long as the normal velocity at the boundary is zero.

In case of a pair of forces acting between the fluid and the medium (Figure 4(b)), the problem is solved as superposition of the solution for the force F′F^{\prime} on the fluid while the medium is fixed (see above) and then for the force FM′F_{\mathrm{M}}^{\prime} on the medium. The total force on the porous material is then FM′=−FF_{\mathrm{M}}^{\prime}=-F. In the second step, we need the solution for the problem where the medium is free to move and subject to the force FM′F_{\mathrm{M}}^{\prime}.

The problem where the medium is moving inside the tightly enclosing confinement without any other flows can be directly solved because the velocity inside the medium in this setting is spatially uniform (zero in the laboratory frame). The resulting drag coefficient is given by the volume of the sphere, multiplied by the drag density ηα2\eta\alpha^2, and reads

Γ=43πR3ηα2.(25)\Gamma=\frac{4}{3}\pi R^3\eta\alpha^2. \tag*{(25)}

It follows that the velocity of the porous medium is

V′=FM′Γ=−F6πηR⋅92(αR)2.(26)\mathbf{V}'=\frac{\mathbf{F}'_{\mathrm{M}}}{\Gamma}=-\frac{\mathbf{F}}{6\pi\eta R}\cdot\frac{9}{2(\alpha R)^2}. \tag*{(26)}

The solution of the full problem is then simply the superposition of the flow induced by a point force F\mathbf{F} in a fixed medium (see Appendix § 2.0.4 § 3.0.2 for an explicit derivation) and the medium moving with velocity V′\mathbf{V}'. Two examples of the solution are shown in Figure 4(c,Figure 4d). A comparison between Eq. (26) and Eq. (24) shows that the velocity in confinement is always larger than in open fluid and that they only become equal if the force acts at the exterior boundary, h=Rh=R. Even though the confinement increases the drag coefficient, it increases the force FM′\mathbf{F}'_{\mathrm{M}} even more.

Discussion

The force balance in Brinkman fluids states that any external force is counterbalanced by the force on the porous material, forces on the walls and long-range stress (pressure). The distribution between these contributions takes different forms in different types of confinement. By applying the Lorentz reciprocal theorem, we could derive the integral forces in the setups we studied more easily than in previous explicit solutions for Newtonian fluids. We expect that the reciprocal theorem will also facilitate the solution of many problems involving Brinkman fluids, such as the hydrodynamic interaction between extended objects and point particles [16]. Although the problems discussed here all involve point forces acting on the fluid, or between the fluid and the medium, the solutions can also be expanded to other sources of flow, such as electroosmosis [17] or diffusioosmosis [18]. In terms of force balance, these flows will have similar properties as collections of force pairs between the fluid and the medium, discussed in Sects. II D and II E.

A natural application of these theoretical results are cytoplasmic flows in biological cells. The cytoplasm is often described with poroelastic models, where the cytosol flows through the cytoskeleton, which forms a porous, elastic mesh [19, 20, 21]. If we neglect the deformations of the cytoskeleton, and also its inhomogeneity and anisotropy, the Brinkman model becomes a good approximation for the cytoplasmic flows.

A biological example closely related to the idealised cylindrical pipe studied in Sect. II B is the cytoplasmic streaming, a flow with velocities up to 100 μm/s\mu\mathrm{m}/\mathrm{s} in some plant cells [22, 23]. The flow is driven by vesicles pulled by motors from the myosin-XI class. Similar cortical flows also appear in C. elegans zygotes, driven by kinesin-1 motors running along microtubules with polar orientation [24] and in Drosophila oocytes [25].

The spherical geometry, discussed in Sections II D and II E, finds its realization in the positioning of the male pronucleus in fertilised eggs [26], e.g. in C. elegans [15, 27] or sea urchin [14, 28], which has also been reproduced in Xenopus egg extracts [29]. The pronucleus first grows a sperm aster consisting of polarised microtubules (Figure 5(b)). Dynein motors then induce a stream of cargo particles (such as endosomes, lysosomes or yolk granules) moving from the periphery to the centre of the aster. Because the microtubules grow shorter at the side facing the cell boundary, the resulting forces pull the pronucleus towards the centre of the cell and the female pronucleus. Although classical biophysical models describe the dynamics of the aster and the cytoplasm in a high level of detail [27], they treat the cytoplasm as a Newtonian fluid and do not consider the local hydrodynamic drag as it moves through the microtubule aster. The forces exerted by dynein motors on the microtubules are therefore used to pull the nucleus to the full extent. Later computational models coupled the cytoplasmic flow to the mechanics of cytoskeletal filaments [30] and indeed showed that the aster behaves as a porous medium where the microtubules contribute the major part to its hydrodynamic drag. Our aim here is to use the simplified model to analytically understand the basic laws of force transduction in such structures.

Figure 5. (a) Cytoplasmic streaming: molecular motors pull cargoes and exert forces (red arrows) on the cytoplasmic fluid. (b) Dynein motors move vesicles along microtubules forming an aster, thereby pulling the pronucleus towards the centre of the cell. If the aster is small compared to the cell, it can be treated as a porous sphere immersed in an infinite fluid domain. (c) Once the aster fills the volume of the cell, it becomes described by a porous sphere with no-slip boundaries. Because microtubules dynamically grow and shrink, their contact with the membrane does not affect the motion of the aster.

In the continuum model we inevitable introduced a number of simplifications. In earlier simulations [30] and experiments [28] the bending of microtubules under force did not play a major role and we therefore conclude that the assumption that the flows do not cause significant deformations of the network is well justified. We treat the cytoplasm as a Newtonian fluid, consistent with experiments showing deviations only on time scales shorter than a second [25]. The polar orientation of microtubules in an aster at first contradicts the assumption of isotropy, but quantitative microscopic models of filamentous porous materials show that the anisotropy of permeability in such media is very small [31]. There is also the assumption of uniform permeability, where we neglect the fact that the microtubules are denser at the centre. We further disregard any effects of inhomogeneity, i.e., any additional effect that could arise because the vesicles are moving along microtubules and not uniformly through the medium. While these details deserve a closer consideration, we expect that they will not significantly affect the main results.

To determine the velocity of the microtubule aster, we need to distinguish two situations. Initially, the aster is small and can be treated as a porous sphere in unconfined fluid, as studied in Sec. II D. Later, the aster fills most of the volume of the cell, while the dynamic nature of the microtubules still allows it to move inside it. The situation corresponds to the porous sphere with no-slip confinement (Sec. II E).

For a small aster, the effective force of the motors pulling on it is reduced by the factor ∣FM′/F′∣|F'_M/F'|, evaluated from Eq. (21) and averaged over the volume of the aster. The factor is 1 in the limit α→0\alpha\to0, as expected in a Newtonian fluid and assumed in [27]. In a denser material, with αR≫1\alpha R \gg1, the efficiency of force generation is increasingly attenuated, as a large fraction of the force exerted by the vesicle on the fluid is transmitted back to the porous material. The attenuation, seen as the ratio between the solid and dashed lines in Figure 3(d) is stronger at the centre of the aster than at the periphery.

Once the aster extends over the volume of the cell, the force transmission becomes 100% efficient. The counterintuitive consequence is that a dynein motor pulling a microtubule against a small vesicle produces as much force as if it was anchored to the membrane – another common mechanism of centering [32]. We note, however, that this measure of efficiency is defined with respect to forces. Energetically, an anchored motor would still be more efficient because it moves at a smaller velocity. Furthermore, although its drag coefficient increases significantly as it extends over the whole volume of the cell, the aster still moves faster than in an unconfined fluid.

The application of hydrodynamic models has decisively contributed to our understanding of many cellular processes [33]. Whereas computational models are able to reproduce and interpret the experimental observations in great detail, we have shown that many fundamental aspects of force conservation and force transduction can be understood with idealised, analytically solvable, fluid-dynamic models. In addition to the examples shown here, we expect the approach to be applicable to a wide range of hydrodynamic processes in cell biology which are currently being discovered at a rapid pace.

Funding. This work was supported by the Slovenian Research and Innovation Agency (A.V., grant number P1-0099). This investigation was initiated during A.V.’s research visit as part of the REF 2029 Visitors Programme, hosted by the STEM Faculty at the Open University in Milton Keynes.

Declaration of interests. The authors declare no conflicts of interest.

Lorentz reciprocal theorem for Brinkman fluids

The Lorentz reciprocal theorem is a property of the Stokes flow that provides an integral identity connecting two different solutions of the Stokes equation: the main and the auxiliary problem [34]. By using a known exact solution as auxiliary problem, integral quantities such as force on an object can be determined without explicitly solving the main problem. The reciprocal theorem can be generalized to flows described by the Brinkman equation. For 2D Brinkman flows, this was demonstrated by [35]. The Brinkman fluid can also be seen as a special case of the poroelastic model, for which a reciprocal theorem has been derived recently [36]. In the following, we recapitulate the derivation for Brinkman flows in 3D. The derivation allows a spatially inhomogeneous parameter α\alpha and therefore holds, for example, for spaces partly consisting of the porous medium and partly of the ordinary fluid of the same viscosity.

We consider two solutions (main and auxiliary) of the Brinkman equation (Eq. (2)) with different force densities,

∇⋅σ−ηα2v+f=0,∇⋅σ^−ηα2v^+f^=0(27)\nabla\cdot\boldsymbol{\sigma} - \eta\alpha^{2}\boldsymbol{v} + \boldsymbol{f} = 0,\qquad\nabla\cdot\hat{\boldsymbol{\sigma}} - \eta\alpha^{2}\hat{\boldsymbol{v}} + \hat{\boldsymbol{f}} = 0 \tag*{(27)}

where the stress tensor of each flow is given by

σ=−pI+2ηE,σ^=−p^I+2ηE^(28)\boldsymbol{\sigma} = -p\boldsymbol{I} + 2\eta\boldsymbol{E},\qquad\hat{\boldsymbol{\sigma}} = -\hat{p}\boldsymbol{I} + 2\eta\hat{\boldsymbol{E}} \tag*{(28)}

with E=12(∇v+(∇v)T)\boldsymbol{E} = \frac{1}{2}(\nabla\boldsymbol{v} + (\nabla\boldsymbol{v})^{\mathrm{T}}). We start with the identity

∇⋅(σ^⋅v)=(∇⋅σ^)⋅v+σ^:∇v=ηα2v^⋅v−f^⋅v−p^∇⋅v+2ηE^:E.(29)\nabla\cdot(\hat{\boldsymbol{\sigma}} \cdot\boldsymbol{v}) = (\nabla\cdot\hat{\boldsymbol{\sigma}}) \cdot\boldsymbol{v} + \hat{\boldsymbol{\sigma}} : \nabla\boldsymbol{v} = \eta\alpha^{2}\hat{\boldsymbol{v}}\cdot\boldsymbol{v} - \hat{\boldsymbol{f}}\cdot\boldsymbol{v} - \hat{p}\nabla\cdot\boldsymbol{v} + 2\eta\hat{\boldsymbol{E}}:\boldsymbol{E}. \tag*{(29)}

The third term in the right-hand-side expression vanishes because ∇⋅v^=0\nabla\cdot\hat{\boldsymbol{v}}=0. By subtracting the equivalent identity for ∇⋅(σ⋅v^)\nabla\cdot(\boldsymbol{\sigma}\cdot\hat{\boldsymbol{v}}), we obtain

∇⋅(σ^⋅v)−∇⋅(σ⋅v^)=−f^⋅v+f⋅v^.(30)\nabla\cdot(\hat{\boldsymbol{\sigma}}\cdot\boldsymbol{v})-\nabla\cdot(\boldsymbol{\sigma}\cdot\hat{\boldsymbol{v}})=-\hat{\boldsymbol{f}}\cdot\boldsymbol{v}+\boldsymbol{f}\cdot\hat{\boldsymbol{v}}. \tag*{(30)}

After integrating over volume V\mathcal{V} and applying the divergence theorem, the reciprocal theorem follows

∮∂Vv⋅σ^⋅n dS+∫Vv⋅f^ dV=∮∂Vv^⋅σ⋅n dS+∫Vv^⋅f dV,(31)\oint_{\partial\mathcal{V}} \boldsymbol{v}\cdot\hat{\boldsymbol{\sigma}}\cdot\boldsymbol{n}\,\mathrm{d}S+\int_{\mathcal{V}}\boldsymbol{v}\cdot\hat{\boldsymbol{f}}\,\mathrm{d}V = \oint_{\partial\mathcal{V}}\hat{\boldsymbol{v}}\cdot\boldsymbol{\sigma}\cdot\boldsymbol{n}\,\mathrm{d}S+\int_{\mathcal{V}}\hat{\boldsymbol{v}}\cdot\boldsymbol{f}\,\mathrm{d}V, \tag*{(31)}

with n\boldsymbol{n} representing a unit surface normal vector pointing outward.

Axisymmetric point force in a porous tube

To determine the solution for a point-force singularity acting along the axis of a porous tube, we employ the image solution technique [37]. The core idea is to express the solution as a superposition of the free-space solution (in the absence of confinement) and an image solution that is force-free in the interior and together with the free-space solution satisfies the boundary conditions. We use cylindrical coordinates and represent the solution using Fourier-Bessel integrals.

By taking the divergence of the Brinkman equation (1), we obtain a Poisson equation for the pressure:

Δp=F∂∂zδ(r).(32)\Delta p = F \frac{\partial}{\partial z}\delta(r). \tag*{(32)}

In an infinite Brinkman fluid medium, its solution (equivalent to the potential of an electrostatic dipole) in Fourier-Bessel space is given by

p∞=F2π2∫0∞kK0(kρ)sin⁡(kz) dk.(33)p^\infty= \frac{F}{2\pi^2}\int_0^\infty kK_0(k\rho)\sin(kz)\,\mathrm{d}k. \tag*{(33)}

For a given pressure, the velocity field vz∞v_z^\infty is determined by the Helmholtz equation

(Δ−α2)vz∞=∂p∞∂z−Fδ(r).(34)(\Delta-\alpha^2)v_z^\infty= \frac{\partial p^\infty}{\partial z}-F\delta(r). \tag*{(34)}

It is solved by

vz∞=F2πηα2∫0∞(−k2K0(kρ)+q2K0(qρ))cos⁡(kz) dk,(35)v_z^\infty= \frac{F}{2\pi\eta\alpha^2}\int_0^\infty\left(-k^2K_0(k\rho)+q^2K_0(q\rho)\right)\cos(kz)\,\mathrm{d}k, \tag*{(35)}

with q=k2+α2q=\sqrt{k^2+\alpha^2}. The radial component vρ∞v_\rho^\infty can then be determined from the incompressibility equation as

vρ∞=F2πηqα2∫0∞k(kK1(kρ)−qK1(qρ))sin⁡(kz) dk.(36)v_\rho^\infty= \frac{F}{2\pi\eta q\alpha^2}\int_0^\infty k\left(kK_1(k\rho)-qK_1(q\rho)\right)\sin(kz)\,\mathrm{d}k. \tag*{(36)}

By evaluating the above integrals, we obtain the known fundamental solution of the Brinkman equation [38]

p∞=F4πzs3,vz∞=F8πη(B1(β)s+B2(β)z2s3),vρ∞=F8πηB2(β)ρzs3.(37)p^\infty= \frac{F}{4\pi}\frac{z}{s^3},\quad v_z^\infty= \frac{F}{8\pi\eta}\left(\frac{B_1(\beta)}{s}+B_2(\beta)\frac{z^2}{s^3}\right),\quad v_\rho^\infty= \frac{F}{8\pi\eta}\frac{B_2(\beta)\rho z}{s^3}. \tag*{(37)}

We have defined the abbreviation β=αs\beta=\alpha s with s=(ρ2+z2)12s=(\rho^2+z^2)^{\frac{1}{2}} denoting the distance from the singularity position. The functions B1B_1 and B2B_2 are given by

B1(β)=2e−β(1+1β+1β2)−2β2,B2(β)=6β2−2e−β(1+3β+3β2),(38)B_1(\beta)=2e^{-\beta}\left(1+\frac{1}{\beta}+\frac{1}{\beta^2}\right)-\frac{2}{\beta^2},\quad B_2(\beta)=\frac{6}{\beta^2}-2e^{-\beta}\left(1+\frac{3}{\beta}+\frac{3}{\beta^2}\right), \tag*{(38)}

In the limit α→0\alpha\to0, B1=B2=1B_1=B_2=1, which simplifies Eqs. (37) to the classical Stokeslet.

To determine the image solution, we start with an arbitrary axisymmetric solution of the homogeneous equation (Δ−α2)v=∇p(\Delta-\alpha^2)\mathbf{v}=\nabla p. Again, by taking its divergence, we obtain Δp=0\Delta p=0. A general axisymmetric solution of the Laplace equation can be written as

p∗=−F2π2∫0∞A(k)I0(kρ)sin⁡(kz) dk,(39)p^*=-\frac{F}{2\pi^2}\int_0^\infty A(k)I_0(k\rho)\sin(kz)\,\mathrm{d}k, \tag*{(39)}

with an unknown function A(k)A(k). A general solution of the Brinkman equation follows as a superposition of the particular solution v=−α−2∇p\mathbf{v}=-\alpha^{-2}\nabla p and a general solution of the homogeneous equation (Δ−α2)vz=0(\Delta-\alpha^2)v_z=0:

vz∗=F2πηα2∫0∞(kA(k)I0(kρ)+qB(k)I0(qρ))cos⁡(kz) dk,(40)v_z^*=\frac{F}{2\pi\eta\alpha^2}\int_0^\infty\left(kA(k)I_0(k\rho)+qB(k)I_0(q\rho)\right)\cos(kz)\,\mathrm{d}k, \tag*{(40)}
vρ∗=F2πηqα2∫0∞k(A(k)I1(kρ)+B(k)I1(qρ))sin⁡(kz) dk,(41)v_\rho^*=\frac{F}{2\pi\eta q\alpha^2}\int_0^\infty k\left(A(k)I_1(k\rho)+B(k)I_1(q\rho)\right)\sin(kz)\,\mathrm{d}k, \tag*{(41)}

with another arbitrary function B(k)B(k). Again, the radial function was determined such that it satisfies ∇⋅v=0\nabla\cdot\mathbf{v}=0.

By enforcing no-slip boundary conditions at ρ=R\rho=R, which correspond to vanishing radial and axial velocities, the functions AA and BB are determined as

A=Φ(k,q)RD,B=Φ(q,k)RD.(42)A=\frac{\Phi(k,q)}{RD},\quad B=\frac{\Phi(q,k)}{RD}. \tag*{(42)}

with

Φ(x,y)=xR(yK1(xR)I0(yR)+xK0(xR)I1(yR))−y(43)\Phi(x,y)=xR\left(yK_{1}(xR)I_{0}(yR)+xK_{0}(xR)I_{1}(yR)\right)-y \tag*{(43)}

and denominator

D=kI0(kR)I1(qR)−qI0(qR)I1(kR).(44)D=kI_{0}(kR)I_{1}(qR)-qI_{0}(qR)I_{1}(kR). \tag*{(44)}

Examples of the resulting flow fields are shown in Figure 1(d). For small values of αR\alpha R, the flow contains viscous toroidal eddies, which were already studied by [39] in a Stokes fluid. However, the eddies vanish when the value of αR\alpha R exceeds approximately 4.7.

The hydrodynamic force exerted on the inner wall of the tube is calculated by integrating the hydrodynamic viscous stress tensor over the cylindrical wall

FW=−2πR∫−∞∞σρz∣ρ=R dz,(45)F_{\mathrm{W}}=-2\pi R\int_{-\infty}^{\infty}\left.\sigma_{\rho z}\right|_{\rho=R}\,\mathrm{d}z, \tag*{(45)}

with σρz=η(∂ρvz+∂zvρ)\sigma_{\rho z}=\eta\left(\partial_{\rho}v_{z}+\partial_{z}v_{\rho}\right). Because vρv_{\rho} vanishes at ρ=R\rho=R, the force involves the contribution from η∂zvρ\eta\partial_{z}v_{\rho} only. By first integrating with respect to zz and then with respect to kk, we obtain

FW=−2I1(αR)/(αR)−1I2(αR)F,(46)F_{\mathrm{W}}=-\frac{2I_{1}(\alpha R)/(\alpha R)-1}{I_{2}(\alpha R)}F, \tag*{(46)}

in agreement with Eq. (12) when setting h=0h=0. We note that FWF_{\mathrm{W}} varies between −F-F and 0.

The force due to the pressure at both ends of the tube can be evaluated as

FP2=±πR2lim⁡z→±∞p.(47)\frac{F_{\mathrm{P}}}{2}=\pm\pi R^{2}\lim_{z\to\pm\infty}p. \tag*{(47)}

Because p∞p^{\infty} decays with ∣z∣−2|z|^{-2}, its contribution to the integral is zero. To account for the contribution from the image solution p∗p^{*}, we use a variable substitution u=kzu=kz and take the limit z→±∞z\to\pm\infty. Note that p∗p^{*} becomes independent of ρ\rho as zz approaches infinity. We obtain

FP=I0(αR)−1I2(αR)F,(48)F_{\mathrm{P}}=\frac{I_{0}(\alpha R)-1}{I_{2}(\alpha R)}F, \tag*{(48)}

which varies between FF and 2F2F. This equation aligns with the pressure force derived from Eq. (11) when setting h=0h=0.

It can readily be checked that

F=FW+FP,(49)F=F_{\mathrm{W}}+F_{\mathrm{P}}, \tag*{(49)}

so that part of the force is transmitted to the wall and the remainder manifests as pressure at both ends of the tube. The total force the fluid exerts on the porous material is therefore zero.

Parallel point force in a porous medium near a wall

Next, we examine the case of a point force acting parallel to an infinitely extended no-slip wall in the xyxy-plane. The point force is positioned at a distance hh above the wall. Without loss of generality, we assume the point force is directed along the xx-axis. To satisfy the no-slip boundary conditions at the wall, we employ the image solution technique and represent the solution as the superposition of a free-space Brinkmanlet and an image that is force-free in the fluid domain.

The problem can be solved using a 2D Fourier transform technique. Accordingly, in 2D Fourier space, the flow variables are expressed using kx=kcos⁡ϕk_{x}=k\cos\phi and ky=ksin⁡ϕk_{y}=k\sin\phi, where kk represents the wavenumber. Note that the zz-coordinate is not transformed. The 2D Fourier-transformed Brinkman equations read

−ikxp~+η(∂zzv~x−q2v~x)=−F~xδ(z−h),(50)-ik_{x}\widetilde{p}+\eta\left(\partial_{zz}\widetilde{v}_{x}-q^{2}\widetilde{v}_{x}\right)=-\widetilde{F}_{x}\delta(z-h), \tag*{(50)}
−ikyp~+η(∂zzv~y−q2v~y)=0,(51)-ik_{y}\widetilde{p}+\eta\left(\partial_{zz}\widetilde{v}_{y}-q^{2}\widetilde{v}_{y}\right)=0, \tag*{(51)}
−∂zp~+η(∂zzv~z−q2v~z)=0,(52)-\partial_{z}\widetilde{p}+\eta\left(\partial_{zz}\widetilde{v}_{z}-q^{2}\widetilde{v}_{z}\right)=0, \tag*{(52)}

where, again, q=k2+α2q=\sqrt{k^2+\alpha^2}. The incompressibility condition in 2D Fourier space is expressed as

ikxv~x+ikyv~y+∂zv~z=0.(53)ik_x\tilde{v}_x+ik_y\tilde{v}_y+\partial_z\tilde{v}_z=0. \tag*{(53)}

We use the method introduced by [40, 41] and define the longitudinal and transverse components of the velocity field as

v~l=v~xcos⁡ϕ+v~ysin⁡ϕ,v~t=v~xsin⁡ϕ−v~ycos⁡ϕ,(54)\tilde{v}_l=\tilde{v}_x\cos\phi+\tilde{v}_y\sin\phi,\qquad\tilde{v}_t=\tilde{v}_x\sin\phi-\tilde{v}_y\cos\phi, \tag*{(54)}

and similarly for the longitudinal and transverse components of the force [42, 43]. The continuity equation ((C4)) establishes a direct relationship between the longitudinal and normal components of the velocity through

v~l=ik∂zv~z.(55)\tilde{v}_l=\frac{i}{k}\partial_z\tilde{v}_z. \tag*{(55)}

From Eqs. (50) and (51) we find that the transverse component of the velocity field is governed by the following second-order differential equation

∂zzv~t−q2v~t=−F~tηδ(z−h).(56)\partial_{zz}\tilde{v}_t-q^2\tilde{v}_t=-\frac{\tilde{F}_t}{\eta}\delta(z-h). \tag*{(56)}

By taking the partial derivatives of Eqs. (50) and (51) with respect to zz, and using Eq. (53) to eliminate v~x\tilde{v}_x and v~y\tilde{v}_y and Eq. (52) to eliminate the pressure, we obtain the following fourth-order differential equation for the zz-component of the velocity field

∂zzzzv~z−(k2+q2)∂zzv~z+k2q2v~z=ikF~lηδ′(z−h).(57)\partial_{zzzz}\tilde{v}_z-(k^2+q^2)\partial_{zz}\tilde{v}_z+k^2q^2\tilde{v}_z=\frac{ik\tilde{F}_l}{\eta}\delta'(z-h). \tag*{(57)}

Considering the regularity conditions at infinity, only the terms with decaying exponentials should be retained. In a bulk fluid medium, the solution of Eqs. (55) through (C8) is [44]

v~t∞=F~t2ηqe−q∣z−h∣,(58)\tilde{v}_t^\infty=\frac{\tilde{F}_t}{2\eta q}e^{-q|z-h|}, \tag*{(58)}
v~z∞=ikF~l2ηα2sgn⁡(z−h)(e−q∣z−h∣−e−k∣z−h∣),(59)\tilde{v}_z^\infty=\frac{ik\tilde{F}_l}{2\eta\alpha^2}\operatorname{sgn}(z-h)\left(e^{-q|z-h|}-e^{-k|z-h|}\right), \tag*{(59)}
v~l∞=F~l2ηq2(qe−q∣z−h∣−ke−kz),(60)\tilde{v}_l^\infty=\frac{\tilde{F}_l}{2\eta q^2}\left(qe^{-q|z-h|}-ke^{-kz}\right), \tag*{(60)}

with sgn⁡(x)=x/∣x∣\operatorname{sgn}(x)=x/|x| denoting the sign function. The corresponding pressure follows from Eq. (52)

p~∞=−iF~l2e−k∣z−h∣.(61)\tilde{p}^\infty=-\frac{i\tilde{F}_l}{2}e^{-k|z-h|}. \tag*{(61)}

The image solution can be represented as a general solution of the homogeneous equations analogue to Eqs. (56) and (57)

v~t∗=F~t2ηAe−qz,v~z∗=iF~l2ηq2(Be−kz+Ce−qz),(62)\tilde{v}_t^*=\frac{\tilde{F}_t}{2\eta}Ae^{-qz},\qquad\tilde{v}_z^*=\frac{i\tilde{F}_l}{2\eta q^2}\left(Be^{-kz}+Ce^{-qz}\right), \tag*{(62)}

where AA, BB, and CC are unknown wavenumber-dependent functions. In addition, v~l∗\tilde{v}_l^* can be determined from Eq. (55) as

v~l∗=F~l2ηq2(Be−kz+qkCe−qz).(63)\tilde{v}_l^*=\frac{\tilde{F}_l}{2\eta q^2}\left(Be^{-kz}+\frac{q}{k}Ce^{-qz}\right). \tag*{(63)}

The corresponding solution for the pressure is

p~∗=iF~l2kBe−kz.(64)\tilde{p}^*=\frac{i\tilde{F}_l}{2k}Be^{-kz}. \tag*{(64)}

The functions AA, BB and CC are obtained from the conditions that v~t∞+v~t∗=0\tilde{v}^{\infty}_{t}+\tilde{v}^{*}_{t}=0, v~l∞+v~l∗=0\tilde{v}^{\infty}_{l}+\tilde{v}^{*}_{l}=0 and v~z∞+v~z∗=0\tilde{v}^{\infty}_{z}+\tilde{v}^{*}_{z}=0 at z=0z=0 as

A=−e−qhq,B=k2qe−qh−(k+q)e−khq−k,C=k2ke−kh−(k+q)e−qhq−k.A=-\frac{e^{-qh}}{q},\qquad B=k\frac{2qe^{-qh}-(k+q)e^{-kh}}{q-k},\qquad C=k\frac{2ke^{-kh}-(k+q)e^{-qh}}{q-k}.

To calculate the force exerted on the wall, we integrate the stress σxz=η(∂xvz+∂zvx)\sigma_{xz}=\eta\left(\partial_xv_z+\partial_zv_x\right) over the surface of the wall. Because vz=0v_z=0 at the boundary, the first term vanishes and force can be calculated as

FW=η2πlim⁡k→0∫02π∂zv~x∣z=0 dϕ=Fe−αh,(65)F_{\mathrm{W}}=\frac{\eta}{2\pi}\lim_{k\to0}\int_{0}^{2\pi}\left.\partial_z\tilde{v}_x\right|_{z=0}\,\mathrm{d}\phi=Fe^{-\alpha h}, \tag*{(65)}

in agreement with Eq. (16).

The far-field pressure is obtained by evaluating p~=p~∞+p~∗\tilde{p}=\tilde{p}^{\infty}+\tilde{p}^{*} in the limit of small kk and transforming the result back to real space, which gives

p=Fx2πr3(1−e−αh).(66)p=\frac{Fx}{2\pi r^3}\left(1-e^{-\alpha h}\right). \tag*{(66)}

Axisymmetric point force inside a porous sphere

We employ the image solution technique to find the solution for a point force acting at position h∈[0,R]h\in[0,R] along the zz-axis. The radial and azimuthal velocities can be expressed with a stream function ψ\psi as

vr=1r2sin⁡θ∂ψ∂θ,vθ=−1rsin⁡θ∂ψ∂r.(67)v_r=\frac{1}{r^2\sin\theta}\frac{\partial\psi}{\partial\theta},\qquad v_\theta=-\frac{1}{r\sin\theta}\frac{\partial\psi}{\partial r}. \tag*{(67)}

The Brinkman equation in terms of the stream function then reads [45]

D2(D2−α2)ψ=0,(68)\mathcal{D}^2\left(\mathcal{D}^2-\alpha^2\right)\psi=0, \tag*{(68)}

with the differential operator

D2=∂2∂r2+sin⁡θr2∂∂θ(1sin⁡θ∂∂θ).(69)\mathcal{D}^2=\frac{\partial^2}{\partial r^2}+\frac{\sin\theta}{r^2}\frac{\partial}{\partial\theta}\left(\frac{1}{\sin\theta}\frac{\partial}{\partial\theta}\right). \tag*{(69)}

We express the solution of the Brinkman equation inside the porous sphere as a superposition of the free space solution around the point force and a force-free image solution:

ψ(i)=ψ∞+ψ∗.(70)\psi^{(i)}=\psi^{\infty}+\psi^{*}. \tag*{(70)}

The corresponding solution of the Stokes flow outside the porous sphere is denoted by ψ(o)\psi^{(o)}. By decomposing the stream function as ψ=ψ(1)+ψ(2)\psi=\psi^{(1)}+\psi^{(2)}, where ψ(1)\psi^{(1)} satisfies D2ψ(1)=0\mathcal{D}^2\psi^{(1)}=0 and ψ(2)\psi^{(2)} satisfies (D2−α2)ψ(2)=0(\mathcal{D}^2-\alpha^2)\psi^{(2)}=0, the stream functions can be decomposed into angular modes as [46, 47]

ψ=F8πη∑n=1∞ψn(r)Pn1(cos⁡θ)sin⁡θ.(71)\psi=\frac{F}{8\pi\eta}\sum_{n=1}^{\infty}\psi_n(r)P_n^1(\cos\theta)\sin\theta. \tag*{(71)}

where Pn1(cos⁡θ)=dPn(cos⁡θ)/dθP_n^1(\cos\theta)=\mathrm{d}P_n(\cos\theta)/\mathrm{d}\theta are representing the associated Legendre polynomials of the first order. Likewise, we express the pressure field as

p=F8π∑n=1∞pn(r)Pn(cos⁡θ).(72)p=\frac{F}{8\pi}\sum_{n=1}^{\infty}p_n(r)P_n(\cos\theta). \tag*{(72)}

By expressing Eqs. (37) in spherical coordinates, the free-space stream function for a Brinkman fluid medium can be derived as

ψ∞=F4πηα2r2s3(1−(1+αs)e−αs)sin⁡2θ,(73)\psi^{\infty}=\frac{F}{4\pi\eta\alpha^2}\frac{r^2}{s^3}\left(1-(1+\alpha s)e^{-\alpha s}\right)\sin^2\theta, \tag*{(73)}

with s=(r2+h2−2hrcos⁡θ)12s = \left(r^2 + h^2 - 2hr\cos\theta\right)^{\frac{1}{2}} representing the distance from the singularity position. For simplicity, we rescaled all lengths by the sphere radius RR. The above solution can be expanded according to Eq. (71) by using the orthogonality properties of Legendre polynomials. The radial part of each term is derived as

ψn∞=2α2h((2n+1)(rh)12In+12(αh)Kn+12(αr)−(hr)n)for r>h,(74)\psi_n^\infty= \frac{2}{\alpha^2 h}\left((2n+1)\left(\frac{r}{h}\right)^{\frac{1}{2}} I_{n+\frac{1}{2}}(\alpha h)K_{n+\frac{1}{2}}(\alpha r)-\left(\frac{h}{r}\right)^n\right)\quad\text{for }r>h, \tag*{(74)}
ψn∞=2α2h((2n+1)(rh)12Kn+12(αh)In+12(αr)−(rh)n+1)for r<h(75)\psi_n^\infty= \frac{2}{\alpha^2 h}\left((2n+1)\left(\frac{r}{h}\right)^{\frac{1}{2}} K_{n+\frac{1}{2}}(\alpha h)I_{n+\frac{1}{2}}(\alpha r)-\left(\frac{r}{h}\right)^{n+1}\right)\quad\text{for }r<h \tag*{(75)}

and the corresponding pressure field is

pn∞=2nr2(hr)n−1for r>h,(76)p_n^\infty= \frac{2n}{r^2}\left(\frac{h}{r}\right)^{n-1}\quad\text{for }r>h, \tag*{(76)}
pn∞=−2(n+1)h2(rh)nfor r<h.(77)p_n^\infty= -\frac{2(n+1)}{h^2}\left(\frac{r}{h}\right)^n\quad\text{for }r<h. \tag*{(77)}

For the image solution in the Brinkman fluid inside the sphere, we use the general solution [47]

ψn∗=1α2(Anrn+1+Bnr12In+12(αr)),(78)\psi_n^* = \frac{1}{\alpha^2}\left(A_n r^{n+1}+B_n r^{\frac{1}{2}}I_{n+\frac{1}{2}}(\alpha r)\right), \tag*{(78)}

with the pressure

pn∗=(n+1)Anrn.(79)p_n^* = (n+1)A_n r^n. \tag*{(79)}

Outside the sphere, a general axisymmetric solution of the Stokes equation is typically expressed in terms of Gegenbauer polynomials [37, 48]. Transformed to the basis defined in Eq. (71), it can be written as

ψn(o)=anrn+bnrn−2,(80)\psi_n^{(o)} = \frac{a_n}{r^n}+\frac{b_n}{r^{n-2}}, \tag*{(80)}

with

pn(o)=−2n(2n−1)bnrn+1.(81)p_n^{(o)} = -2n(2n-1)\frac{b_n}{r^{n+1}}. \tag*{(81)}

The components of the fluid velocity, which follow from the stream function via Eq. (67), can be cast in the form

vr=F8πη∑n=1∞Rn(r)Pn(cos⁡θ),vθ=F8πη∑n=1∞Tn(r)Pn1(cos⁡θ).(82)v_r = \frac{F}{8\pi\eta}\sum_{n=1}^{\infty}R_n(r)P_n(\cos\theta),\qquad v_\theta= \frac{F}{8\pi\eta}\sum_{n=1}^{\infty}T_n(r)P_n^1(\cos\theta). \tag*{(82)}

For the free-space components, we obtain

Rn∞=2n(n+1)α2hr2(−(2n+1)(rh)12In+12(αh)Kn+12(αr)+(hr)n),(83)R_n^\infty= \frac{2n(n+1)}{\alpha^2 h r^2}\left(-(2n+1)\left(\frac{r}{h}\right)^{\frac{1}{2}}I_{n+\frac{1}{2}}(\alpha h)K_{n+\frac{1}{2}}(\alpha r)+\left(\frac{h}{r}\right)^n\right), \tag*{(83)}
Tn∞=2α2hr2((2n+1)(rh)12In+12(αh)Hn(αr)−n(hr)n),(84)T_n^\infty= \frac{2}{\alpha^2 h r^2}\left((2n+1)\left(\frac{r}{h}\right)^{\frac{1}{2}}I_{n+\frac{1}{2}}(\alpha h)H_n(\alpha r)-n\left(\frac{h}{r}\right)^n\right), \tag*{(84)}

where we have defined the abbreviation

Hn(αr)=αrKn−12(αr)+nKn+12(αr).(85)H_n(\alpha r)=\alpha rK_{n-\frac{1}{2}}(\alpha r)+nK_{n+\frac{1}{2}}(\alpha r). \tag*{(85)}

For the image solution, we have

Rn∗=−n(n+1)α2r2(Anrn+1+Bnr12In+12(αr)),(86)R_n^*=-\frac{n(n+1)}{\alpha^2 r^2}\left(A_n r^{n+1}+B_n r^{\frac{1}{2}}I_{n+\frac{1}{2}}(\alpha r)\right), \tag*{(86)}
Tn∗=−1α2r2((n+1)Anrn+1+Bnr12Qn(αr)),(87)T_n^*=-\frac{1}{\alpha^2 r^2}\left((n+1)A_n r^{n+1}+B_n r^{\frac{1}{2}}Q_n(\alpha r)\right), \tag*{(87)}

with

Qn(αr)=αrIn−12(αr)−nIn+12(αr).(88)Q_n(\alpha r)=\alpha rI_{n-\frac{1}{2}}(\alpha r)-nI_{n+\frac{1}{2}}(\alpha r). \tag*{(88)}

The solution of the Stokes flow outside the porous sphere is

Rn(o)=−n(n+1)(anrn+2+bnrn).(89)R_n^{(o)}=-n(n+1)\left(\frac{a_n}{r^{n+2}}+\frac{b_n}{r^n}\right). \tag*{(89)}
Tn(o)=nrn+2an+n−2rnbn.(90)T_n^{(o)}=\frac{n}{r^{n+2}}a_n+\frac{n-2}{r^n}b_n. \tag*{(90)}

The unknown sequences AnA_n, BnB_n, ana_n, and bnb_n can be determined based on whether the porous sphere has open boundaries or no-slip confinement.

Porous sphere with open boundaries

For a porous sphere with open boundaries, it is necessary to satisfy the continuity of both the velocity and the viscous stress tensor at r=1r=1. The coefficients within the porous sphere can be expressed in the form

An=2nMnDn,Bn=2(2n+1)NnDn.(91)A_n=\frac{2nM_n}{D_n},\qquad B_n=\frac{2(2n+1)N_n}{D_n}. \tag*{(91)}

where

Mn=(4n2−1)In+12(αh)−αhn+12((2n−1)In−12(α)+αIn+12(α)).(92)M_n=(4n^2-1)I_{n+\frac{1}{2}}(\alpha h)-\alpha h^{n+\frac{1}{2}}\left((2n-1)I_{n-\frac{1}{2}}(\alpha)+\alpha I_{n+\frac{1}{2}}(\alpha)\right). \tag*{(92)}
Nn=n(2n−1)hn+12−ΛnIn+12(αh),(93)N_n=n(2n-1)h^{n+\frac{1}{2}}-\Lambda_n I_{n+\frac{1}{2}}(\alpha h), \tag*{(93)}

with

Λn=α(n+1)(αKn+12(α)−(2n−1)Kn−12(α))+n(4n2−1)Kn+12(α).(94)\Lambda_n=\alpha(n+1)\left(\alpha K_{n+\frac{1}{2}}(\alpha)-(2n-1)K_{n-\frac{1}{2}}(\alpha)\right)+n(4n^2-1)K_{n+\frac{1}{2}}(\alpha). \tag*{(94)}

The denominator is given by

Dn=h32(α(n+1)(αIn+12(α)+(2n−1)In−12(α))+n(4n2−1)In+12(α)).D_n=h^{\frac{3}{2}}\left(\alpha(n+1)\left(\alpha I_{n+\frac{1}{2}}(\alpha)+(2n-1)I_{n-\frac{1}{2}}(\alpha)\right)+n(4n^2-1)I_{n+\frac{1}{2}}(\alpha)\right).

Outside the porous sphere, the coefficients can similarly be expressed in the form

an=(2n+1)Snα2Dn,bn=−(2n+1)WnDn.(95)a_n=\frac{(2n+1)S_n}{\alpha^2D_n},\qquad b_n=-\frac{(2n+1)W_n}{D_n}. \tag*{(95)}

where

Sn=α(α(n−2)In+12(α)−2(2n−1)In−12(α))hn+12+ΔnIn+12(αh),(96)S_n=\alpha\left(\alpha(n-2)I_{n+\frac{1}{2}}(\alpha)-2(2n-1)I_{n-\frac{1}{2}}(\alpha)\right)h^{n+\frac{1}{2}}+\Delta_n I_{n+\frac{1}{2}}(\alpha h), \tag*{(96)}
Wn=nIn+12(α)hn+12+(n+1)In+12(αh),(97)W_n=nI_{n+\frac{1}{2}}(\alpha)h^{n+\frac{1}{2}}+(n+1)I_{n+\frac{1}{2}}(\alpha h), \tag*{(97)}

with

Δn=2(4n2−1)+α2(n+1).(98)\Delta_n=2(4n^2-1)+\alpha^2(n+1). \tag*{(98)}

The streamlines of the resulting flow are shown in Figure 3(e,Figure 3f) for the values h=0h=0 and h=0.75h=0.75.

The hydrodynamic force exerted on the background fluid can be obtained by surface integration

Fz=2π∫r>1(σrr(o)cos⁡θ−σrθ(o)sin⁡θ)r2sin⁡θ dθ.(99)F_z=2\pi\int_{r>1}\left(\sigma_{rr}^{(o)}\cos\theta-\sigma_{r\theta}^{(o)}\sin\theta\right)r^2\sin\theta\,d\theta. \tag*{(99)}

leading to the same result as Eq. (21) in the main text derived using the reciprocal theorem.

Porous sphere with no-slip confinement

Considering no-slip boundary conditions, where the velocity is zero at r=1r = 1, the series coefficients of the solution inside the porous sphere are determined as

An=2αCnLn,Bn=2(2n+1)EnLn,(100)A_n = \frac{2\alpha C_n}{L_n}, \qquad B_n = \frac{2(2n+1)E_n}{L_n}, \tag*{(100)}

where

Cn=−(2n+1)(In−12(α)Kn+12(α)+In+12(α)Kn−12(α))In+12(αh)+In−12(α)hn+12,(101)\begin{aligned} C_n ={}& -(2n+1)\left(I_{n-\frac{1}{2}}(\alpha)K_{n+\frac{1}{2}}(\alpha) + I_{n+\frac{1}{2}}(\alpha)K_{n-\frac{1}{2}}(\alpha)\right) I_{n+\frac{1}{2}}(\alpha h) \\ &+ I_{n-\frac{1}{2}}(\alpha)h^{n+\frac{1}{2}}, \tag*{(101)} \end{aligned}
En=((2n+1)Kn+12(α)+αKn−12(α))In+12(αh)−hn+12.(102)E_n = \left((2n+1)K_{n+\frac{1}{2}}(\alpha) + \alpha K_{n-\frac{1}{2}}(\alpha)\right) I_{n+\frac{1}{2}}(\alpha h) - h^{n+\frac{1}{2}}. \tag*{(102)}

The denominator is given by

Ln=h32(αIn−12(α)−(2n+1)In+12(α)).(103)L_n = h^{\frac{3}{2}}\left(\alpha I_{n-\frac{1}{2}}(\alpha) - (2n+1)I_{n+\frac{1}{2}}(\alpha)\right). \tag*{(103)}

Two examples of the flow are shown in Figure 4(c,Figure 4d).

References

  1. [1]H. Brenner, Pressure drop due to viscous flow through cylinders, J. Fluid Mech. 6, 542 (1959).DOI
  2. [2]N. Liron and R. Shahar, Stokes flow due to a Stokeslet in a pipe, J. Fluid Mech. 86, 727 (1978).DOI
  3. [3]N. Pliskin and H. Brenner, Experiments on the pressure drop created by a sphere settling in a viscous liquid, J. Fluid Mech. 17, 89 (1963).DOI
  4. [4]L. A. Mondy, N. Tetlow, A. L. Graham, J. Abbott, and H. Brenner, The pressure drop created by a ball settling in a quiescent suspension of comparably sized spheres, J. Fluid Mech. 353, 31 (1997).DOI
  5. [5]V. Škultéty and A. Morozov, A note on forces exerted by a Stokeslet on confining boundaries, J. Fluid Mech. 882, 6477 (2020).DOI
  6. [6]H. C. Brinkman, A calculation of the viscous force exerted by a flowing fluid on a dense swarm of particles, Flow Turbul. Combust. 1, 27 (1949).
  7. [7]H. C. Brinkman, On the permeability of media consisting of closely packed porous particles, Flow Turbul. Combust. 1, 81 (1949).DOI
  8. [8]J. R. Blake, A note on the image system for a Stokeslet in a no-slip boundary, Math. Proc. Camb. Phil. Soc. 70, 303 (1971).DOI
  9. [9]M. Abramowitz and I. A. Stegun, Handbook of Mathematical Functions (Dover, New York, 1972).
  10. [10]S. Navardi and S. Bhattacharya, A new lubrication theory to derive far-field axial pressure difference due to force singularities in cylindrical or annular vessels, J. Math. Phys. 51, 81 (2010).DOI
  11. [11]K. Misiunas, S. Pagliara, E. Lauga, J. R. Lister, and U. F. Keyser, Nondecaying hydrodynamic interactions along narrow channels, Phys. Rev. Lett. 115, 038301 (2015).pubmed.ncbi.nlm.nih.gov/26230830
  12. [12]B. Felderhof, Frictional properties of dilute polymer solutions, Physica A 80, 63 (1975).DOI
  13. [13]R. Kree and A. Zippelius, Self-propulsion of droplets driven by an active permeating gel, Eur. Phys. J. E 41, 096601 (2018).arxiv.org/abs/1803.08695
  14. [14]H. Tanimoto, A. Kimura, and N. Minc, Shape–motion relationships of centering microtubule asters, J. Cell Biol. 212, 777 (2016).DOI
  15. [15]A. De Simone, A. Spahr, C. Busso, and P. Gönczy, Uncovering the balance of forces driving microtubule aster migration in C. elegans zygotes, Nat. Commun. 9, 2283 (2018).DOI
  16. [16]A. Daddi-Moussa-Ider, Y. Hosaka, A. Vilfan, and R. Golestanian, Axisymmetric monopole and dipole flow singularities in proximity of a stationary no-slip plate immersed in a Brinkman fluid, Phys. Rev. Res. 5, 033030 (2023).
  17. [17]D. Coelho, M. Shapiro, J. Thovert, and P. Adler, Electroosmotic phenomena in porous media, J. Colloid Interface Sci. 181, 619 (1996).
  18. [18]H. J. Keh, Diffusiophoresis of charged particles and diffusioosmosis of electrolyte solutions, Curr. Opin. Colloid Interface Sci. 24, 13 (2016).DOI
  19. [19]E. Moeendarbary, L. Valon, M. Fritzsche, A. R. Harris, D. A. Moulding, A. J. Thrasher, E. Stride, L. Mahadevan, and G. T. Charras, The cytoplasm of living cells behaves as a poroelastic material, Nat. Mater. 12, 253 (2013).DOI
  20. [20]A. Mogilner and A. Manhart, Intracellular fluid mechanics: Coupling cytoplasmic flow with active cytoskeletal gel, Annu. Rev. Fluid Mech. 50, 347 (2018).DOI
  21. [21]M. Moradi, W. Shi, and E. Nazockdast, General solutions of linear poro-viscoelastic materials in spherical coordinates, J. Fluid Mech. 946, A22 (2022).DOI
  22. [22]J.-W. van de Meent, A. J. Sederman, L. F. Gladden, and R. E. Goldstein, Measurement of cytoplasmic streaming in single plant cells by magnetic resonance velocimetry, J. Fluid Mech. 642, 5 (2010).DOI
  23. [23]R. E. Goldstein, I. Tuval, and J.-W. van de Meent, Microfluidics of cytoplasmic streaming and its implications for intracellular transport, Proc. Natl. Acad. Sci. U.S.A. 105, 3663 (2008).DOI
  24. [24]K. Kimura, A. Mamane, T. Sasaki, K. Sato, J. Takagi, R. Niwayama, L. Hufnagel, Y. Shimamoto, J.-F. Joanny, S. Uchida, and A. Kimura, Endoplasmic-reticulum-mediated microtubule alignment governs cytoplasmic streaming, Nat. Cell Biol. 19, 399 (2017).DOI
  25. [25]S. Ganguly, L. S. Williams, I. M. Palacios, and R. E. Goldstein, Cytoplasmic streaming in Drosophila oocytes varies with kinesin activity and correlates with the microtubule cytoskeleton architecture, Proc. Natl. Acad. Sci. U.S.A. 109, 15109 (2012).pubmed.ncbi.nlm.nih.gov/22949706
  26. [26]J. L. Meaders and D. R. Burgess, Microtubule-based mechanisms of pronuclear positioning, Cells 9, 505 (2020).DOI
  27. [27]T. Shinar, M. Mana, F. Piano, and M. J. Shelley, A model of cytoplasmically driven microtubule-based motion in the single-celled Caenorhabditis elegans embryo, Proc. Natl. Acad. Sci. U.S.A. 108, 10508 (2011).DOI
  28. [28]H. Tanimoto, J. Sallé, L. Dodin, and N. Minc, Physical forces determining the persistency and centring precision of microtubule asters, Nat. Phys. 14, 848 (2018).DOI
  29. [29]S. Reinsch and E. Karsenti, Movement of nuclei along microtubules in Xenopus egg extracts, Curr. Biol. 7, 211 (1997).pubmed.ncbi.nlm.nih.gov/9395409
  30. [30]E. Nazockdast, A. Rahimian, D. Needleman, and M. Shelley, Cytoplasmic flows as signatures for the mechanics of mitotic positioning, Mol. Biol. Cell 28, 3261 (2017).
  31. [31]C. Y. Wang, Stokes flow through a rectangular array of circular cylinders, Fluid Dyn. Res. 29, 65 (2001).DOI
  32. [32]H.-Y. Wu, G. Kabacaoğlu, E. Nazockdast, H.-C. Chang, M. J. Shelley, and D. J. Needleman, Laser ablation and fluid flows reveal the mechanism behind spindle and centrosome positioning, Nat. Phys. 20, 157 (2024).DOI
  33. [33]D. Needleman and M. Shelley, The stormy fluid dynamics of the living cell, Phys. Today 72, 32 (2019).DOI
  34. [34]H. Masoud and H. A. Stone, The reciprocal theorem in fluid dynamics and transport phenomena, J. Fluid Mech. 879, P1 (2019).DOI
  35. [35]B. Bet, R. Georgiev, W. Uspal, H. B. Eral, R. van Roij, and S. Samin, Calculating the motion of highly confined, arbitrary-shaped particles in Hele–Shaw channels, Microfluid. Nanofluid. 22, 103 (2018).DOI
  36. [36]M. Moradi, W. Shi, and E. Nazockdast, A reciprocal theorem for biphasic poro-viscoelastic materials, J. Fluid Mech. 997, A62 (2024).DOI
  37. [37]J. Happel and H. Brenner, Low Reynolds Number Hydrodynamics: With Special Applications to Particulate Media (Springer Netherlands, The Hague, 1983).DOI
  38. [38]I. D. Howells, Drag due to the motion of a Newtonian fluid through a sparse random array of small fixed rigid objects, J. Fluid Mech. 64, 449 (1974).DOI
  39. [39]J. R. Blake, On the generation of viscous toroidal eddies in a cylinder, J. Fluid Mech. 95, 209 (1979).DOI
  40. [40]T. Bickel, Brownian motion near a liquid-like membrane, Eur. Phys. J. E 20, 379 (2006).DOI
  41. [41]T. Bickel, Hindered mobility of a particle near a soft interface, Phys. Rev. E 75, 041403 (2007).pubmed.ncbi.nlm.nih.gov/17500890
  42. [42]A. Daddi-Moussa-Ider and S. Gekle, Hydrodynamic interaction between particles near elastic interfaces, J. Chem. Phys. 145, 014905 (2016).
  43. [43]A. Daddi-Moussa-Ider and S. Gekle, Brownian motion near an elastic cell membrane: A theoretical study, Eur. Phys. J. E 41, 19 (2018).
  44. [44]A. Daddi-Moussa-Ider, A. Guckenberger, and S. Gekle, Long-lived anomalous thermal diffusion induced by elastic cell membranes on nearby particles, Phys. Rev. E 93, 012612 (2016).
  45. [45]I. Pop and D. Ingham, Flow past a sphere embedded in a porous medium based on the Brinkman model, Int. Commun. Heat Mass Transfer 23, 865 (1996).DOI
  46. [46]D. Palaniappan, On some general solutions of transient Stokes and Brinkman equations, J. Theor. Appl. Mech. 52, 405 (2014).
  47. [47]H. Nanguia and Q. S. Pak, Squirming motion in a Brinkman medium, J. Fluid Mech. 855, 554 (2018).
  48. [48]S. Kim and S. J. Karrila, Microhydrodynamics: principles and selected applications (Dover Publications, Mineola, New York, 2005).

Paper details

vlnc:W_av3ysxyn
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents