WorksPhysics and Astronomy
A microstructural analysis of 2D halide perovskites: Stability and functionality
Abstract
Recent observations indicated that the photoelectric conversion properties of perovskite materials are intimately related to the presence of superlattice structures and other unusual nanoscale features in them. The low dimensional or mixed dimensional halide perovskite family are found to be more efficient materials for device application compared to 3-dimensional halide perovskites. The emergence of perovskite solar cell has revolutionized the solar cell industry because of their flexible architecture and rapidly increased efficiency. Tuning the dielectric constant, charge separation are the main objective in designing a photovoltaic device that can be explored using 2-dimensional perovskite family. Thus, revisiting the fundamental properties of perovskite crystals could reveal further possibilities for recognizing these improvements towards device functionality. In this context, this review discusses the material properties of 2-dimensional halide perovskite and related optoelectronic devices aiming particularly for solar cell application.
Introduction
As witnessed in the past decade, the halide perovskite family has emerged as a high-performance photovoltaic material. This reappearance has involved extensive development of the three-dimensional (3D) perovskites, specifically .The crystallographic formula of halide perovskite (HP) materials comprised of A, organic cation such as methylammonium (MA): or alkali cation or mixing of both, B the metal cation ( or ), and X the halide anions (X = , , or Cl). HPs are mainly classified into two categories depending on the occupancy of A-site whether an organic-molecular cation or an elemental cation. The categories are organic-inorganic hybrid HPs and all-inorganic HPs, respectively. In hybrid HPs, the organic cations occupying A-site of the perovskite structure are usually non-symmetric and inclined to rotation at room temperature and above [8]. This extraordinary phenomena has been hardly observed in other materials. As a result, hybrid HPs have the interconnected octahedra continued in an ordered manner that form the crystal structure with local disorder located within the framework. At room temperature, the most-reviewed hybrid HP, or (), the reorientation of polar ion are found in octahedral (between the faces, corners, or edges) having a residence time of ~14 ps [42]. At lower temperatures, the rotational dynamics in HPs are slowed down (Wu et al., 2017) following their dielectric response. HPs can have different tunable chemical compositions, such as , , , well known as Ruddlesden-Popper (RP) phases (Yu et al., 2017). The defects in the crystal, crystallographic alignments, surfaces, grain boundaries, and interfaces in HPs can be customized preferentially. These preferential nano- and micro-structures can be addressed using in-depth conventional microscopic characterization methods such as atomic force microscopy (AFM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). As an example, consider the case of a perovskite solar cell (PSC). A PSC includes a hybrid organic-inorganic or all-inorganic perovskite structured compound as the light-harvesting active layer. The compositional variation of the material and its dependency on phase transition temperature are related to electrical and ionic properties of the active layer [15, 94, 41]. Thus we can infer that measuring a minute variation of structural property and optimizing the same will be a quality control measure for optoelectronic devices.
The large exciton binding energy due to the reduced dielectric screening and quantum confinement are the most fascinating optoelectronic properties of two-dimensional (2D) materials. 2D HPs with its tuneable photophysical properties and superior chemical stability compared to their 3D counterpart [92] (Ding et al 2018; Dong et al 2019) have created a great influence on the semiconductor research and technology fields. 2D HPs obey stereochemical rules that determine the growth of the perovskite sheets, (i)corner-sharing, (ii)edge-sharing, and (iii)face-sharing- octahedral connections has been experimentally observed. Here the characteristics for size restriction for A site is determined by the suitability of a cation spacer whether a) its net +ve charge at the perovskite attaching point and substitution amount (b) capacity of hydrogen bonding (c) flexible stereochemical arrangement, (d) ability of space filling [50]. Most cations are found to have corner sharing 2D structure but sometime the cation-imposed configuration strain in 2D network that stabilizes edge-sharing or face sharing networks [35]. In 2D perovskites, extra larger organic cations (L) are inserted as spacers, separating the inorganic metal halide octahedra layers to form quantum well superlattices that is different from conventional 3D HP. Here introducing hydrophobic spacer cations, the ionic lattice of inorganic octahedrons are effectively isolated from the ambient water molecules. The newly introduced additional spacing cations and asymmetric lattice structures provide tunable intrinsic physical features, such as dielectric constant, optical band gap, and exciton binding energy, [5]. As a result, the photophysical behaviors like exciton dynamics [60], charge carrier transport [75], and electron−phonon coupling [73] that strongly influence the performance of optoelectronic devices (light emitting diode (LED), solar cell(SC)) can also be modulated accordingly [92]. In a recent report, the mechanical properties of are found to be anisotropic, and the organic components and van der Waals interactions between layers play a significant role in the structural stability of the 2D structure [26]. They found that the substituting the organic parts with rigid and multifunctional organic components with Pb will improved stability and carrier mobility of the PSC absorber layer.
The interaction of electromagnetic fields with photo- and electro-active materials is the heart of energy conversion research. Graphene, hexagonal boron nitride, transition metal dichalcogenides, MXenes etc. other classical 2D materials are being widely studied due to their fascinating properties such as high electrical conductivity, low density, large surface area, tunable electric and magnetic properties [57, 51, 34]. Pristine graphene is a zero-bandgap semimetal. while RGO and GO are a semiconductor and an insulator, respectively. 2D TMDs display semiconducting nature[24] (Rao et al. 2009). MXenes sometimes behaves as metals, semiconductors, superconductors, topological insulators, and, most importantly, half-metallic characteristics [54, 55, 1]. graphene and related two-dimensional (2D) materials propose extraordinary advancement towards in device performance even at the atomic scale. A compromised combination of these 2D materials with silicon chips promotes a massively enhanced potential compatible for on silicon technology. Low cost, simple and inexpensive layered two-dimensional (2D) halide perovskites are a novel class of materials with outstanding layer-dependent tunable optical properties, generation of room temperature stable excitons, and modified exciton binding energy originating from the quantum and dielectric confinement effects. They also offer the improved environmental stability and photostability needed for the light absorbing layer photovoltaic devices. The enormous potential of this thin film SC technology is expected to become a low-cost commercial alternative in the near future to the presently available silicon photovoltaic. This manuscript evolves as follows: introduction to material properties, highlighting 2D perovskite structural aspects. Next, the characterization that identifies exotic material property of 2D HP has been discussed. Finally, the microstructural characteristics of 2D HPs that leads to promising potential applications as high-performance optoelectronic devices especially SC has been pointed out.
STRUCTURAL ASPECTS OF 2D HP: ENGINEERED ENERGY LANDSCAPE
Microscopically, layered HPs contain of mono or few thin atomic layers of HP (Gao et al., 2018). Atomically (morphologically) thin HPs or crystallographically layered HPs are considered as 2D/quasi-2D (q-2D) HPs. Dimensional confinement upon crystallization of HPs using the long-chain organic ligands-templated growth, [76, 47, 67] or self-templated growth, [46, 56] (Ha et al 2014) preserving formula results morphological 2D/q-2D HPs. Using bulky organic separators and by slicing 3D HPs along , , and crystal plane three different layered crystallographic 2D/q-2D HPs are obtained. As a consequence, the chemical formulae of 2D HPs modified methodically according to the number of layers and crystal plane orientation. The chemical formula of specifically belongs to , , and oriented HP family respectively. The oriented layered HP family, owing to their high acceptance to many distinct organic and inorganic components, is the most extensively investigated among them. The HP family oriented along direction are allocated further into two sub-categories, RP and Dion–Jacobson (DJ) [58] type. However, the DJ HPs are not often studied and applied in practical devices, thus less popular in device field [49]. The name of RP HPs derived from their resemblance in crystal with inorganic RP perovskites [63]. To emphasis on the comparison in crystal structure of HPs we will focus our discussion to a schematic. Figure 1 (a) describes schematic of the 3D structure and the [001] projections of conventional inorganic cubic and orthorhombic perovskite phases and RP phases as labelled in ref (Yu et al., 2017). Here, the material or , is found to be composed of “n” layers of unit cells separated by an extra CsBr layer. The RP phases are considered as a repeatedly integral extrinsic stacking error, designed by shifting two neighbouring units by an in-plane lattice vector (1/2 1/2) compared to each other. Figure 1(b) compares between experimental and simulated scanning TEM (STEM) images of typical domains in 2D nanosheets of . The three panels compares perovskite I: 6-layer perovskite phase (upper panel), 1-layer n = 2 RP phase (middle panel), and perovskite II: 6-layer perovskite phase with −PbBr termination (bottom layer). From the figure it is clearly observed that RP domains and perovskite domains are well-connected in 2D nanosheets owing to their crystal structures similarity, and all of these domain boundaries aligned in the directions at atomic-scale. The details of the STEM mode of operation/characterisation will be discussed in the next section.
For clarity, the general formula for 2D hybrid RP perovskite can be rewritten as (RNH)MX or (NHRNH)MX, where M is metal cation including Pb, Cu, and Sn, R: prototype organic molecule e.g. phenethylammonium (PEA) or butylammonium (BA) [52]. In hybrid RP perovskites, a extraordinary ability to regulate the thickness of the inorganic layers are found, which is a highly needed characteristics for photovoltaic (PV) applications, specifically SCs. As a consequence, RP perovskites are found to be the most used and studied. For the construction of interconnected few layers of corner-sharing M-X octahedra in q-2D HPs, the short-chain inorganic or organic cations are required. The value of “n” in the general formulae considered here is the number of layers in 2D and q-2D HPs. For n = 1, we get the 2D HPs. q-2D HPs are obtained for n 2. The intrinsically insulating large organic layers induce multiple quantum well structures [11] in between the assemblies of these organic layers with M-X octahedron layers. As a result, the 2D and q-2D RP HPs are found to exhibit electronic and quantum confinement even in thin films [16, 71]. A comparison between 2D and 3D network of perovskite and the modified band structure has been described in ref [73]. Figure 2 (A) describes projection of the 3D hybrid perovskite structure. It highlights an inorganic linkage of corner sharing metal halide octahedral described by red colour, while the interstitial organic cations are marked with blue, black colour. Green colour region emphasise the limit on cation size. A projection down the c-axis of the 2D hybrid perovskite is schematically depicted in Figure 2(B). It shows the successive arrangement of organic layer as shown in blue and black colour and red inorganic layers that shares the corners. The thickness of inorganic and organic layers are marked as and respectively, for n=1. Here the green region emphasis the restriction on the area of cross section but not on the of organic cation length. The energy band diagram of 2D structures, valence band (VB), conduction band (CB), electronic bandgap (), and optical or excitonic bandgap (blue colour) are labelled in the Figure 2(C). The organic framework (with lager HOMO-LUMO gap) has a dielectric constant while the inorganic slabs have a (). A dielectric confinement effect is originated by the alternation of low dielectric constant of the organic moiety and a high dielectric constant of the Pb halide layers [32, 39]. In 2D perovskites due to a dielectric confinement effect in the layers, the electrons are strongly attracted to the holes. They attribute higher exciton binding energies for 2D compared to their 3D counterpart.
For SCs application, the exciton binding energy should be as small as possible. The lead HPs with , have bandgap, comparable to 3D perovskites the dielectric constant increases largely with , are able to perform decently as SC absorbers [59]. The bandgap is one of the most crucial parameters in SC applications. It determines the maximum theoretical efficiency for the corresponding single p-n junction device according to the Shockley-Queisser limit [64]. A bandgap of 1.34 eV results in a power conversion efficiency (PCE) of about 33.5%, [64, 70] while materials with bandgaps eV are found to be the smart choice for tandem SCs. The bandgap for 2D HP is typically determined by the composition and thickness of the inorganic layers. The bulkier halides lessen the bandgap. For , 2D perovskites with formula , have bandgaps of about 3.8, 3.0 and 2.5eV for , and respectively [38]. The heavier, less electronegative halides have more delocalized electronic density and it better overlap with that of the metal atoms [70]. Therefore, halide substitutions can be a method for systematically engineered the bandgap of 2D hybrid HP by adjusting their composition of the chemical constituents. The procedure allows broad absorption across visible and near-infrared region of wavelengths. The other way of the bandgap and photoluminescence (PL) wavelength modification is by changing the value. With increase in , the bandgap becomes smaller, and tends towards the bandgap value of 3D perovskite as approaches to , and the PL peak shifts asymptotically towards lower energies with increase in [72]. Again, the coefficient of absorption (COA) is directly proportional to the strength of electronic dipole transitions. In 2D-perovskites, light absorption is lesser due to a low density of metal/halogen atoms causing a lower absorption cross-section. COA increases rapidly as the value increases. 2D perovskites with , are comparable to 3D perovskites, have high enough COA can harvest most of the incoming radiation. Following the trend, a general scaling law was proposed to determine the binding energy of Wannier-Mott excitons in perovskite quantum wells of arbitrary layer thickness [4]. In another approach [53], modified orientation of the conducting perovskite layers through choice of organic cation has been achieved. Interestingly, they found conducting layered organic-inorganic halide containing oriented perovskite sheet. Here it must be mentioned that surface modification also plays a critical role in device engineering. It was also observed that the layer edge electrons which are not related to the surface charging effect; but associated with the local energy states corresponding to of the edge electronic structure [78]. Therefore, in the next section the focus of discussion is on the characterisation of engineered HP energy landscape and extrapolation of these specific features towards device application.
MICROSTRUCTURAL CHARACTERISATION HP: IMPROVEMENT OF DEVICE FUNCTIONALITY
Crystallographic Characterisation
Conductivities and carrier mobilities of layered perovskite depends on the crystallographic direction. Generally the conductivity and mobility are found to be significantly improved when measured along the planes of the inorganic layers. TEM and x-ray crystallographic technique helps to understand the device crystalline feature needed for improved device performance. A comparative structural study of 3D and HPs has been followed in this section.
The specific interactions between an electron beam with high energy and a thin electron-transparent sample are captured as the contrast of TEM images [already discussed in Figure 1 of earlier section]. High resolution (resolution ~ atomic scale) imaging, can be achieved in STEM mode, with few detectors to generate the images (example BF: bright field, ADF: annular dark field, and HAADF: high-angle annular dark field). The crystallographic information is extracted from electron diffraction patterns (EDPs) of the area of interest in the specimen understudy. Due to the modification of Bragg conditions in thin films, EDPs suffer from imprecise crystallographic data. Energy dispersive spectroscopy (EDS) and electron energy loss spectroscopy (EELS) gives the site-specific chemical composition information. EELS allows to gather evidences about a range of sample- related aspects, such as thickness, chemical surrounding, bonding, bandgap etc. [77] (Yu et al. 2017).
On the other hand, novel EDS detectors allows efficient collection of specimen compositional data even at the atomistic scale. In a recent review the beam sensitivity of HP that guide the TEM characterization has been thoroughly discussed [12]. For beam-sensitive HPs materials, leading beam-damage mechanisms involve phonon mediated heating, displacement of atoms and defect formation i.e. knock-on damage, and damage by inelastic scattering and rupture of chemical bonds i.e. radiolysis. [18] Several approaches such as, optimizing the accelerating voltage, low-dose imaging with improved cameras can be employed to overcome degradation in beam-sensitive materials. The photon induced dynamics and polarization of ions can affect the physical properties and device performance of HPs. Thus photon induced dynamics of is a major challenge for direct imaging of organic cations in TEM. Using iterative cross-correlations-built algorithm to the filtered images, Zhang et al. (Zhang et al., 2018) successfully observed the ordered nanoscale domains with off-centered cations with differing orientations in crystals. The cations are found to exhibit configurations along the normal and parallel relative to the projection direction, forming in-plane and out-of-plane electric dipoles, respectively. Accordingly, the structural models and the corresponding simulated projected potential describes that the local deviations in the orientation is responsible for ferroelectricity and/or polarization in hybrid HPs. The crystal network of hybrid HPs is much ‘‘softer’’ compared with conventional oxide perovskites. As a result, there is a high probability for local vibrations in structures, modification in structures and symmetry of the crystals. Thus to visualize the pristine structure of perovskite prepared via a catalyst-free solution-phase method (Yu et al., 2016), Yu et al. employed HRTEM in addition to small-dose in-line holography. The specimen under observation exhibit an atomically layered 2D nanosheet morphology. Employing focal series, they showed the existence of dual phases of cubic and orthorhombic HP within the nanosheets. TEM can also identify the misalignment between the successive grains and even describe the boundary plane. Twin boundaries in HP was identified by Rothmann et al. [62] using TEM. These twin boundaries in specimens can originate during growth, phase transition, or even under mechanical stress. As HPs, exhibit extreme chemical sensitivity, etching using a chemical solution is not a viable method for observing twin boundaries. Thus, electron back-scattered diffraction (EBSD) and TEM are essential tools for revealing twinning in HPs. Based on low-dose TEM imaging and selected area EDPs (SAEDPs), Rothmann et al. showed the presence of twinning in tetragonal , where these boundaries appeared in the form of parallel striped bands of few hundred nm width within grains. Although the device performance upon incorporation of the material was not clearly described by them. However, another recent study has pointed that twin boundaries can be very effective in restricting photocarriers (Li et al., 2018). The other report [3], prompts flexibility of HPs nanocrystals (NC) upon halide changes and temperature variation which has been investigated following high-resolution synchrotron X-ray total scattering data. Variations in local structure of these NCs was found to exhibits orthorhombic tilting of octahedra within locally ordered subdomains. These subdomains are linked by a 2D/3D network of twin boundaries through which the coherent arrangement of the over the whole NC is preserved. Thus, we believe that controlling the properties of twining (size, orientations, etc.) could be a viable approach for the achieving and modifying the characteristics newly designed HPs.
The grain-boundary chemistry in PSCs, intensely influence carrier recombination and potential transport of ionic and molecular species, thus affecting the optoelectronic properties and chemical stability of HPs. The grain-boundary chemistry of HPs dependents on the HP bulk elemental composition, growth conditions, the structure and the kinetics of the boundary, and careful chemical modifications. In a contemporary literature (Zong et al., 2018), triblock copolymer (Pluronic P123) functionalized HP are found to result in water-resistant HPs. The copolymer establish the interaction with HP grains via its hydrophilic tails, while its hydrophobic core is placed towards the center of the copolymer wetting film. As a consequence, a water resistant HP with higher stability was obtained.
Morphological and conductive characterization: Scanning Probe Microscopy
Scanning probe microscopy, including AFM, Kelvin probe force microscopy (KPFM), conductive AFM (C-AFM), has been broadly applied to explore the local physical, electromagnetic or molecular topographies at microscopic scale. AFM and KPFM are two different modes of microscopic technique that operate at constant or variable bias condition. Specifically, KPFM captures the contact potential difference (CPD) between conductive tip and the sample (Chen et al., 2019). Under an alternative voltage, the CPD is measured by using a vibrating capacitor with Kelvin method [2]. Instead of current, the sensitivity of KPFM is improved, by recording the electrostatic force interaction between the tip and the sample. By accurate adjustment of the tip work function on the reference sample, the other materials surface work function can be determined [66]. In high resolution C-AFM [85, 68] the current–voltage characteristics of the sample surface could be easily captured by the mapping of the topography. A large current flow points high conductivity of sample, a strategic character of charge transport (Wang et al., 2016, Lee et al., 2018, Xu et al., 2018, Eichhorn et al 2018, Bristowe et al., 2015, Si et al., 2017). Thus, by C-AFM, the conductivity difference among dissimilar perovskite films can be captured and their transport characteristics (at grain boundaries, in grain interiors) can be distinguished with the nanoscale resolution. Even for phase pure perovskites where the compositional engineering are used to overcome difficulties in obtaining high-quality sample, ambient instability degrades the device performance. Lee et al, reported the fabrication of phase-pure formamidinium-lead tri-iodide perovskite films with excellent optoelectronic quality and stability. They showed that incorporation of 1.67 mol% of 2D PEA lead iodide into the precursor solution allows the formation of phase-pure formamidinium perovskite with an enhanced photoluminescence lifetime [40]. Figure 3 describes the band alignment and local conductivity with 2D perovskite as described by [40]. Figure 3(A) describes that the device schematic comprising polycrystalline film of 3D perovskite with grain boundaries containing 2D perovskite, while (B) describes the layer by layer Tauc plots and UV photoelectron spectroscopic analysis of the device band structure. The bare C-AFM images of FAPbI and with films of 2D perovskite on ITO glass coated with SnO are shown in Figure 3 (C, E) and (D, F) respectively. A 100-mV bias voltage was applied to get the images under the room light condition for image (C, D) and low light intensity condition for image (E, F) as provided by the setup. Topology of each film is depicted in the inset of the corresponding images. For (C, D) and (E, F), the corresponding scale bars are shown at the left and right side, respectively. It describes that under ambient light conditions, flow of current in the perovskite film with 2D perovskite was higher at/near the grain boundaries while fairly uniform flow of current was noted in the bare FAPbI film. With light illumination, the flow of current was further enhanced at/near the grain boundaries with 2D perovskite whereas current flow in bare FAPbI film was uniformly increased, which indicates separation of charge and collection of photo-generated electrons is more favourable at grain boundaries with 2D perovskite. On the other hand, the 2D PEAPbI perovskite with aromatic rings and longer alkyl chains is projected to be more resilient to moisture. It guards the defective grain boundaries of 3D perovskite, resulting in significantly improved moisture stability of the film. Regardless of the improved stability, degraded electronic properties of the film is expected due to the poor charge carrier mobility of the 2D perovskite. Interestingly, a report by Wang et al. highlights a prominent conducting feature, observed at the layer edges between the insulating bulk regions of (CHNH)PbI 2D perovskite single crystal. In the bulk region, the electron-hole pairs are tightly bonded. At the layer edges, additional edge state (ES) electrons are located, which control the current detected by the C-AFM measurement [78]. These observations of the metal-like conducting feature at the layer edge of 2D perovskite offers a different dimension for improving the performance of the next-generation optoelectronics and innovative nanoelectronics. Piezo-response force microscopy (PFM) is an AFM-based method depending on the inverse piezoelectric effect analyzing the local electromechanical properties of piezoelectric samples. Remarkably, PFM has been widely employed to study the possible ferroelectricity in MAPbI perovskite [22]. The theoretical calculations suggested presence of ferroelectric domain in the perovskite samples that would result separation of photoexcited electron-hole pair making an internal junction. It allows reduction of recombination through segregation of charge carriers. PFM also ascertains the ferroelectric features in other 2D layered perovskite materials [65, 10] useful as sensors in flexible devices, soft robotics and biomedical devices, a great influence towards next generation devices. However, ferroelectricity of MAPbI is still under debate [79].

Figure 3.
Here would like to mention that, other than conventional microscopic techniques microwave photoconductivity imaging (MIM) on has been proved to be an efficient technique for quantitative estimation of photoconductivity. A recent report highlights the nanoscale photoconductivity imaging of two thin films with different efficiencies by light-stimulated microwave impedance microscopy [14]. Here, unlike the C-AFM technique, a direct contact between the MIM tip and the perovskite thin films is not required. The effective capacitive coupling between the MIM tip and the perovskite thin films at GHz frequencies, overcomes the difficulties of nanoscale electrical properties on samples with a capping layer which is insulating in nature.
Distinctive Spectroscopic Characteristics: An en route to device functionality
The two most general schemes practised to enhance the PCE of 2D and q-2D HPs-based SCs are: i) optimising the layer numbers (n) to get adequate absorption of light and charge generation, ii) refining crystallographic alignment for better charge transport to the electrode. Although the layer number can be easily modified by tuning the composition of 2D and q-2D HPs in precursors, while the controlled orientational growth remains a big challenge. Non-invasive spectroscopic approaches are the easiest to probe these distinctive characteristics of the 2D perovskite specimens compared to conventional microscopic technique as here we don’t need any sample preparation. Here we will discuss, a general scaling law was proposed by Blancon et al., 2018 to determine the binding energy of Wannier-Mott excitons in perovskite quantum wells of arbitrary layer thickness. Figure 4 describes the absorption and PL i.e., optical spectroscopic feature of the 2D and q-2D HP crystals having n =1–5 for inorganic RP perovskite quantum wells following the reference [4]. It specifically highlights (A) scaling of experimentally obtained optical bandgap and (B) photoluminescence spectra for the material. This understanding provides direct insight about the photophysics of RP perovskite materials utilised in practical devices.

Figure 4.
Generally, in 3D HPs, excited charges diffuse quicker than the radiative recombination rate. Thus, most of them are confined at the grain boundary defects. However, in 2D HPs, free charges and excitons co-exists in a small regime, enhancing the radiative combination relative to bulk specimen. Due to the surface and interface defects present in the sample, the non-radiative recombination still controls the energy transfer phenomena and the PL in 2D HPs remains comparatively low. It is evident from these results that layered HPs might not be the good choice for LEDs when one considers high brightness and effective quantum efficiency (EQE). However, owing to their excellent stability and process ability, they are considered to be finest candidates for practical LEDs [86, 13] (Xu et al. 2019).
Metal HPs also show necessary optical–electrical characteristics for PV devices, such as long carrier diffusion lengths, high carrier mobility, strong and broad optical absorption, all of which support the notable PCE of the device. In general, 2D flakes of MAPbI3 is a widely accepted active material for photodetectors for its large COA, high mobility of the carrier and smaller exciton binding energy ( meV, room temperature). 2D RP perovskites are also known to exhibit the excellent photodetection performance. In a recent report by Zhou et al. [93] explained that the RP perovskite film displayed the layer number dependent response spectrum, which is compatible with their absorption spectrum. As the perovskite films are configured into photodetectors, better photodetection property was detected in the film with the higher value. Here the polycrystalline nature of 2D RP perovskites might be the cause behind the observed lower photoresponse. In recent times, photodetection ability of 2D RP perovskites was observed to be considerably upgraded by the replacement of the long direct chain n-BA with branched i-BA using a method of hot-casting processing [17].
The functionality in the devices is mostly dependant on the grain structure of polycrystalline 2D perovskites, but in-situ, chemically specific characterization of 2D perovskite grains are currently limited. Here the polarized ultra-low-frequency Raman microspectroscopy is found to be a simplistic yet influential tool for identifying relative grain orientations in 2D perovskite thin films [74]. Even from temperature-dependent PL spectra of 2D perovskites and following generalized Elliot formula, the evidence of phonon-assisted sidebands are explained by Feldstein et al. They determined the spectral linewidth of the energetically lowest excitonic transitions in view of scattering channels focussing on the emission and absorption of phonons (low-energy acoustic and higher energy optical) [23]. The low-energy, heat-carrying acoustic phonons plays the central role for management of heat in 2D RP-supported devices, remained unexplored for a long time. A recent literature by Guo et al. discusses the generation and transmission of coherent longitudinal acoustic phonons along the 2D RPs cross-plane direction, resulting distinct characterizations of lower-bandgap refractive indices. They have demonstrated a significant drop in group velocity and propagation length of acoustic phonons in 2D RPs compared to the 3D MA lead iodide counterpart [30]. The observed vibrational feature is a consequence of large acoustic impedance disparity between the successive layers of perovskite and large organic cations.
Pump-probe spectroscopy offers a feasible way to identify the carrier dynamics in the 2D perovskite materials [28]. Transient absorption microscopy (TAM) [81] is one of the technique employed to probe diffusion of carrier and two-body recombination processes. Figure 5, as reproduced following Williams et al. [81], describes the schematic of concentration distribution of quantum well that yield a gradient in excitation frequencies and enables a unidirectional flow of energy as a cascade, obtained by TAM. Figure 5 (A) describes the concentration gradient of quantum wells (QWs) throughout a film of layered perovskite. According to the idea, the glass edge of the perovskite film is highly populated with the smallest QWs and the air edge is mostly dense with thickest QWs. Figure 5 (B) Schematically highlights the diagram describing down-hill energy transfer cascade. It is observed that excitonic resonances of the quantum wells decrease with increase in thickness and the direction of electron transfer is same as that of energy transfer as compared to the holes which are moving towards the states of higher energy. For applications such as microcavity lasers, boosting of the two-body recombination processes is desirable. Here, a methodical comparison of the layered films of with phase-pure single crystals disclose that diffusion is blocked by grain boundaries in the films, stimulating two-body recombination. The energy transfer rules the sub-200 ps time scale and the energy levels of the quantum wells are organised such that hole transfer may take place from the air to glass sides of the film at future times. The high-performance nanolasers made up of perovskites have attained low threshold, high quality factor and tunable wavelengths under optical excitation [30, 91, 48]. Their compact volume could entrap the light field in a tiny region and improve the light–matter interactions. Another interesting report establish that quantum wells of colloidal lead halide perovskites can produce fully decoupled multi quantum well (MQW) superlattices (having intralayer local exciton) with ultrathin organic quantum barriers [33], same as the addition of monolayer hybrid boron nitride (h-BN). The obtained result demonstrates that photonic source have emission of narrowband, high quantum yield, improved light outcoupling, and wavelength tenability useful for for nano-antenna (near field) and LED (far field). Even theoretically it was proposed (Li et al., 2020) that the use of superlattice structures is an smart approach (such as mixing of cations and partial substitution of halogens by superhalogens) for expanding the family of perovskites and obtaining excellent optoelectronic materials with improve stability.

Figure 5.
VB of 2D perovskites is predominantly consist of halide p-orbitals hybridized with metal s-orbitals and a CB is of metal p-orbitals dominated. In lead HPs, the corresponding orbitals are of I and and of Pb [27, 21, 20]. In 2D HPs, the existence of Pb and I prompts a large spin-orbit coupling (SOC) which in the presence of structural inversion asymmetry boosts the spin-degeneracy of the CB and VB [36, 37]. It seems that 2D perovskites self-assemble into regular “quantum-well” structures that break the symmetry of the 3D system. It amplify the Rashba-effect and escalates their potential for opto-spintronic applications as observed by transient spectroscopic measurements [89]. The rate of charge carrier recombination and spin-coherence lifetimes of 2D RP perovskite single crystals, (with ) has been reported in Ref (Chen et al., 2017). Charge carrier recombination rates are observed to be fastest for due to the large exciton binding energy and the slowest for . Spin-coherence times at ambient temperature also demonstrate a non-monotonic layer thickness dependency with a growing spin-coherence lifetime, increases for to , followed by a reduction in lifetime for to . For , the longest coherence lifetime of 7 ps was detected. Their observations are dependent on two contributions; a) Rashba-splitting increasing the spin-coherence lifetime for the to the smaller layered systems, b) phonon-scattering increases for smaller layers, reducing the spin-coherence lifetime. The interplay between these two contributions modifies the layer thickness dependency. Here they also measured the carrier dynamics by the exciton bleach kinetics and the spin-coherence dynamics by employing circularly polarized pump and probe pulses.
There from the above discussion we can extract that for device application a stable structure is the most feasible. Figure 6 describes the dimensional reduction, modified/engineered surface for a stable 2D HP device functionality. Remarkably, a report by G. Grancini et al. [29] introduced a stable perovskite device by engineering 2D/3D perovskite junction. The unique gradually-organized 2D/3D multi-dimensional interface produces up to 12.9% efficiency in a carbon-based architecture, and 14.6% in standard mesoporous SCs for 1 year. Their innovative, low-cost and stable architecture has supported the timely commercialization of PSCs. Thus, we propose that a detailed microstructural analysis of 2D HPs are the much needed approach to engineer new materials for energy research application specially SC. In this review we have tried to sum up the characteristics of 2D HPs reported / proposed to have stable architecture feasible for energy research application.

Figure 6.
Conclusion
This review shows that for commercialisation of HP optoelectronic devices, a thorough in-depth characterisation of 2D HP materials are essential. Most unique feature essential for light absorbing layers of solar cell related to this type of material is their optimised dielectric constants and exciton binding energy, compared to conventional semiconductors, and it also include a rotational component connected with relaxation of molecular dipole. Although great efforts have been given to study various 2D HP materials, many challenges still there to utilize these materials in actual practical purposes. But, the fabricated devices using 2D HPs still facing degradation problem. More experimental and theoretical studies are needed in this regard to understand the degradation and improve the stability. On the other hand, there is a critical need of improved procedure of synthesis of single crystals of 2D HP with controlled thickness and large dimension. The above discussions highlights the correlation between the microscopic, crystallographic and molecular structure of 2D layered HP, and it is expected that these photo response properties of the material will be further corroborated towards developing flexible functional and tuneable optoelectronics device in future.
CONFLICT OF INTEREST
The authors declare that the review work was conducted in the absence of any commercial or financial connections that could be construed as a potential conflict of interest.
AUTHOR CONTRIBUTIONS
SB and GKC designed and wrote manuscript. PP supervised this work and revised the manuscript. All authors contributed to the article and agreed on the submitted version.
FUNDING
This work was supported by the Faculty Research Grant [NITC/DEAN(R&C)/FRG/2018-19/3], NIT Calicut and ANERT [ANERT-TECH/11/2019-S(NEP)], Govt. of Kerala, Kerala.
Figure Caption
Figure 1. A) Upper panel: The conventional crystallographic structure of cubic and orthorhombic perovskite phases along with RP phases (for different values of and ). Lower panel: Unit cells and their projections along the [001] direction. (B) Atomic structures of the domains (plausible RP) and the domain boundaries (between the phases of conventional perovskite and RP) and the comparison between the experimental and simulated STEM image. Pure Cs and mixed Pb-Br cation columns are present along the [001] projected direction in conventional 3D structures of perovskite phases, as compared to the all mixed Cs-Pb-Br cation column in RP phases along the same projected direction. The figure is reprinted with permission from Y. Yu et al. (2017) copywrite 2017, American chemical society.
Figure 2. (A) Projection schematic of the 3D HP (Color codes are following: Red, describes a corner shared inorganic network of octahedral metal halide; Blue & Black, describes the interstitial position of the organic cations; Green, emphasizes the size restriction on cation). (B) The projection of the 2D HP along the c-axis (Color codes are following: Blue & Black, represents the organic alteration; Red, represents the corner shared inorganic layers; Green, represents the restriction on area cross-section of organic cation not on the length). inorganic layer thickness and organic layer thickness for . (C) The energy band diagram of 2D HP structures ( and denote the electronic and optical bandgap). Blue color represents the . The figure is reprinted with permission from D. B. Straus and C. R. Kagan et al. (2018) copywrite 2017, American chemical society.
Figure 3. The local conductivity and band alignment in 2D perovskite. (A) The device schematic comprising polycrystalline film of 3D perovskite with grain boundaries containing 2D perovskite. (B) The layer by layer Tauc plots and UV photoelectron spectroscopic analysis of the device band structure.
The bare C-AFM images of FAPbI (C, E) and with films of 2D perovskite (D, F) on ITO glass coated with SnO. 100 mV bias voltage was applied to get the images under the room light condition for (C, D) and low light intensity condition for (E, F) as provided by the setup. Topology of each film is depicted in the inset of the corresponding images. For (C, D) and (E, F), the scale bars are shown at the left and right side, respectively.
The figure is reprinted with permission from J.-W Lee et al. [40] copywrite 2018, Nature publishing group.
Figure 4. Optical spectroscopy, PL (at 4 K blue square symbol and line) and absorption spectra (at 4 K red and 290 K green closed and opened circle) of the RP perovskite crystals with to 5. (A) Scaling of experimentally obtained optical bandgap. (B) Photoluminescence spectra.
The figure is reprinted with permission from J. C. Blancon et al. [4] copywrite 2018, Nature publishing group.
Figure 5. (A) The concentration gradient of quantum wells (QWs) throughout a film of layered perovskite is depicted here. The glass edge of the perovskite film is highly populated with the smallest QWs and the air edge is mostly dense with thickest QWs. (B) Schematic diagram describing down-hill energy transfer cascade. Excitonic resonances of the quantum wells decrease with increase in thickness. The direction of electron transfer is same as that of energy transfer as compared to the holes which are moving towards the states of higher energy.
The figure is reprinted with permission from O. F. Williams et al. [81] copywrite 2019, American chemical society.
Figure 6: Schematic representation of stability and functionality of 2D HP.

Figure 1 (PDF p. 27).

Figure 2 (PDF p. 28).
References
- [1]Anasori, B., Xie, Y., Beidaghi, M., Lu, J., Hosler, B. C., Hultman, L., Kent, P. R. C., Gogotsi, Y., and Barsoum, M. W. (2015). Two-Dimensional, Ordered, Double Transition Metal Carbides (MXenes). ACS Nano. 9(10), 9507-9516. doi:10.1021/acsnano.5b03591DOI
- [2]Benstetter, A. H. G., Liu, D., Frammelsberger, W., and Lanza, M. (2017). Conductive Atomic Force Microscopy: Applications in Nanomaterials, Wiley-VCH Verlag GmbH & Co. KGaA.
- [3]Bertolotti, F., Protesescu, L., Kovalenko, M. V., Yakunin, S., Cervellino, A., Billinge, S. J. L., Terban, M. W., Pedersen, J. S., Masciocchi, N. and Guagliardi, A. (2017) Coherent nanotwins and dynamic disorder in cesium lead halide perovskite nanocrystals, ACS Nano. 11, 3819–3831. doi: 10.1021/acsnano.7b00017DOI
- [4]Blancon, J. C., Stier, A. V., Tsai, H., Nie, W., Stoumpos, C. C., Traoré, B., Pedesseau, L., Kepenekian, M., Katsutani, F., Noe, G. T., Kono, J., Tretiak, S., Crooker, S. A., Katan, C., Kanatzidis, M. G., Crochet, J. J., Even, J., Mohite, A. D. (2018) Scaling law for excitons in 2D perovskite quantum wells Nat. Commun., 9:2254. doi: 10.1038/s41467-018-04659-xDOI
- [5]Blancon, J.-C., Tsai, H., Nie, W., Stoumpos, C. C., Pedesseau, L., Katan, C., Kepenekian, M., Soe, C. M. M., Appavoo, K., Sfeir, M. Y., Tretiak, S., Ajayan, P. M., Kanatzidis, M. G., Even, J., Crochet, J. J. and Mohite, A. D. (2017) Extremely efficient internal exciton dissociation through edge states in layered 2D perovskites, Science 355:1288–1292. doi: 10.1126/science.aal4211DOI
- [8]Chen, T., Foley, B.J., Ipek, B., Tyagi, M., Copley, J.R.D., Brown, C.M., Choi, J.J., and Lee, S.H. (2015). Rotational dynamics of organic cations in the CH₃NH₃PbI₃ perovskite. Phys. Chem. Chem. Phys. 17: 31278–31286. doi:10.1039/C5CP05348JDOI
- [10]Chen, X.-G., Song, X. J., Zhang, Z.-X., Li, P.-F., Ge, J.-Z., Tang, Y.-Y., Gao, J.-X., Zhang, W.-Y., Fu, D.-W., You, Y.-M., and Xiong, R.-G. (2020). Two-dimensional layered perovskite ferroelectric with giant piezoelectric voltage coefficient. J. Am. Chem. Soc. 142(2), 1077–1082. doi:10.1021/jacs.9b12368DOI
- [11]Chen, Z., Guo, Y., Wertz, E. and Shi, J. (2019) Merits and challenges of Ruddlesden–Popper soft halide perovskites in electro-optics and optoelectronics, Adv. Mater. 31:1803514. doi: 10.1002/adma.201803514DOI
- [12]Chen, S. and Gao, P. Challenges, myths, and opportunities of electron microscopy on halide perovskites J. Appl. Phys. 128, 010901 (2020); doi: 10.1063/5.0012310DOI
- [13]Chiba, T., Hayashi, Y., Ebe, H., Hoshi, K., Sato, J., Sato, S. Pu, Y.-J., Ohisa, S., and Kido, J. (2018). Anion-exchange red perovskite quantum dots with ammonium iodine salts for highly efficient light-emitting devices. Nature Photon. 12, 681–687. doi:10.1038/s41566-018-0260-yDOI
- [14]Chu, Z., Yang, M., Schulz, P., Wu, D., Ma, X., Seifert, E., Sun, L., Li, X., Zhu, K. and Lai, K. (2017). Impact of grain boundaries on efficiency and stability of organic-inorganic trihalide perovskites. Nat. Commun. 8, 2230. doi:10.1038/s41467-017-02331-4DOI
- [15]Correa-Baena, J. P., Saliba, M., Buonassisi, T., Grätzel, M., Abate, A., Tress, W. and Hagfeldt, A. (2017) Promises and challenges of perovskite solar cells, Science 358: 739–744. doi: 10.1126/science.aam6323.
- [16]Ding, Y.-F., Zhao, Q.-Q., Yu, Z.-L., Zhao, Y.-Q., Liu, B., He, P.-B., Zhou, H., Li, K. L., Yin, S.-F. and Cai, M.-Q. (2019) Strong thickness-dependent quantum confinement in all-inorganic perovskite Cs₂PbI₄ with a Ruddlesden–Popper structure J. Mater. Chem. C 7: 7433. doi:10.1039/C9TC02267H.DOI
- [17]Dong, R., Lan, C., Xu, X., Liang, X., Hu, X., Li, D., Zhou, Z., Shu, L., Yip, S., Li, C., Tsang, S.- W., and Ho, J. C. (2018). Novel series of quasi-2D Ruddlesdene-Popper perovskites based on short-chained spacer cation for enhanced photodetection. ACS Appl. Mater. Interfaces. 10(22), 19019-19026. doi:10.1021/acsami.8b03517.DOI
- [18]Egerton, R.F., Li, P., and Malac, M. (2004). Radiation damage in the TEM and SEM. Micron 35:399. doi: 10.1016/j.micron.2004.02.003DOI
- [20]Even, J., Pedesseau, L., Dupertruis, M. -A., Jancu, J. -M., and Katan, C. (2012). Electronic Model for Self- Assembled Hybrid Organic/perovskite Semiconductors: Reverse Band Edge Electronic States Ordering and Spin-Orbit Coupling. Phys. Rev. B. 86, 205301. doi:10.1103/PhysRevB.86.205301.DOI
- [21]Even, J., Pedesseau, L., Jancu, J. -M., and Katan, C. (2013). Importance of Spin-Orbit Coupling in Hybrid Organic/inorganic Perovskites for Photovoltaic Applications. J. Phys. Chem. Lett. 4(17), 2999–3005. doi:10.1021/jz401532q.DOI
- [22]Fan, Z., Xiao, J., Sun, K., Chen, L., Hu, Y., Ouyang, J., Ong, K. P., Zeng, K., and Wang, J. (2015). Ferroelectricity of CH₃NH₃PbI₃ perovskite. Phys. Chem. Lett. 6(7), 1155–1161. doi:10.1021/acs.jpclett.5b00389.DOI
- [23]Feldstein, D., Perea-Causín, R., Wang, S., Dyksik, M., Watanabe, K., Taniguchi, T., Plochocka, P., and Malic, E. (2020). Microscopic picture of electron–phonon interaction in two-dimensional halide perovskites. J. Phys. Chem. Lett. 11(23), 9975-9982. doi: 10.1021/acs.jpclett.0c02661DOI
- [24]Ferrari, A. C., Bonaccorso, F., Fal'ko, V., Novoselov, K. S., Roche, S., Bøggild, P. et al. (2015). Science and technology roadmap for graphene, related two-dimensional crystals, and hybrid systems. Nanoscale. 7, 4598-4810. doi:10.1039/C4NR01600ADOI
- [26]Gao, H., Wei, W., Li, L., Tan, Y. and Tang, Y. (2020) Mechanical Properties of a 2D Lead-Halide Perovskite, (C₆H₅CH₂NH₃)₂PbCl₄, by Nanoindentation and First-Principles Calculations, J. Phys. Chem. C, 124, 19204–19211. doi: 10.1021/acs.jpcc.0c04283
- [27]Gebhardt, J., Kim, Y., and Rappe, A. M. (2017). Influence of the dimensionality and organic cation on crystal and electronic structure of organometallic halide perovskites. J. Phys. Chem. C. 121(12), 6569–6574. doi:10.1021/acs.jpcc.7b00890DOI
- [28]Giovanni, D., Chong, W. K., Liu, Y. Y. F., Dewi, H. A., Yin, T., Lekina, Y., Shen, Z. X., Mathews, N., Gan, C. K., and Sum, T. C. (2018). Coherent spin and quasiparticle dynamics in solution processed layered 2D lead halide perovskites. Adv. Sci. 5(10), 1800664. doi: 10.1002/advs.201800664DOI
- [29]Grancini, G., Roldán-Carmona, C., Zimmermann, I., Mosconi, E., Lee, X., Martineau, D., Narbeу, S., Oswald, F., Angelis, F. D., Graetzel, M., and Nazeeruddin, M. K. (2017). One-Year stable perovskite solar cells by 2D/3D interface engineering. Nat. Commun. 8, 15684. doi: 10.1038/ncomms15684DOI
- [30]Guo, P., Stoumpos, C. C., Mao, L., Sadasivam, S., Ketterson, J. B., Darancet, P., Kanatzidis, M. G., and Schaller, R. D. (2018). Cross-plane coherent acoustic phonons in two-dimensional organic-inorganic hybrid perovskites. Nat. Commun. 9(1), 2019. doi:10.1038/s41467-018-04429-9DOI
- [32]Ishihara, T., Takahashi, J. and Goto, T. (1989) Exciton state in two-dimensional perovskite semiconductor (C₁₀H₂₁NH₃)₂PbI₄, Solid State Commun., 69:933. doi:10.1016/0038-1098(89)900935-6
- [33]Jagielski, J., Solari, S. F., Jordan, L., Scullion, D., Blülle, B., Li, Y. –T., Krumeich, F., Chiu, Y. –C., Ruhstaller, B., Santos, E. J. G., and Shih, C. –J. (2020). Scalable photonic sources using two – dimensional lead halide perovskite superlattices. Nat. Commun. 11, 387. doi:10.1038/s41467-019-14084-3DOI
- [34]Jiang, X., Kuklin, A. V., Baev, A. G., Y.Ågren, H. Zhang, H. Prasad, P. N. (2020) Two-dimensional MXenes: From morphological to optical, electric, and magnetic properties and applications Physics Reports, 848, 1-58. doi: 10.1016/j.physrep.2019.12.006.DOI
- [35]Kamminga, M. E.; Fang, H.-H.; Filip, M. R.; Giustino, F.; Baas, J.; Blake, G. R.; Loi, M. A.; Palstra, T. T. M. (2016) Confinement Effects in Low-Dimensional Lead Iodide Perovskite Hybrids. Chem. Mater., 28, 4554–4562. doi: 10.1021/acs.chemmater.6b00809DOI
- [36]Kepenekian, M., and Even, J. (2017). Rashba and Dresselhaus couplings in halide perovskites: Accomplishments and opportunities for spintronics and spin–orbitronics. J. Phys. Chem. Lett. 8, 3362–3370. doi:10.1021/acs.jpclett.7b01015DOI
- [37]Kepenekian, M., Robles, R., Katan, C., Sapori, D., Pedesseau, L., and Even, J. (2015). Rashba and Dresselhaus effects in hybrid organic–inorganic perovskites: From basics to devices. ACS Nano. 9(12), 11557–11567. doi:10.1021/acsnano.5b04409DOI
- [38]Kitazawa, N. (1997) Excitons in two-dimensional layered perovskite compounds: (C₆H₅C₂H₄NH₃)₂Pb(Br,I)₄ and (C₆H₅C₂H₄NH₃)₂Pb(Cl,Br)₄ Mater. Sci. Eng. B 49, 233–238. doi: 10.1016/S0921-5107(97)00132-3DOI
- [39]Koh, T. M., Febriansyah, B. and Mathews, N. (2017) Ruddlesden–Popper perovskite solar cells Chem 2: 326. doi:10.1016/j.chempr.2017.02.015DOI
- [40]Lee, J.-W., Dai, Z., Han, T. H., Choi, C., Chang, S. Y., Lee, S. J., Marco, N. D., Zhao, H., Sun, P., Huang, Y., and Yang, Y. (2018). 2D perovskite stabilized phase-pure formamidinium perovskite solar cells. Nat. Commun. 9, 3021. doi: 10.1038/s41467-018-05454-4DOI
- [41]Lee, M. M., Teuscher, J., Miyasaka, T., Murakami, T. N. and Snaith, H. J. (2012) Efficient hybrid solar cells based on meso-superstructured organometal halide perovskites, Science 338 (6107): 643-647. doi: 10.1126/science.1228604DOI
- [42]Leguy, A.M.A., Frost, J.M., McMahon, A.P., Sakai, V.G., Kockelmann, W., Law, C., Li, X., Foglia, F., Walsh, A., O’Regan, B.C. (2015). The dynamics of methylammonium ions in hybrid organic–inorganic perovskite solar cells. Nat. Commun. 6:7124. doi:10.1038/ncomms8124DOI
- [46]Liu, J., Xue, Y., Wang, Z., Xu, Z.-Q., Zheng, C., Weber, B., Song, J., Wang, Y., Lu, Y., Zhang, Y. and Bao, Q. (2016) Two-dimensional CH₃NH₃PbI₃ perovskite: Synthesis and optoelectronic application, ACS Nano, 10, 3536-3542. doi:10.1021/acsnano.5b07791DOI
- [47]Liu, X.-D., Wang, Q., Cheng, Z.-Q. , Qiu, Y.-H., Zhou, L. and Wang, Q.-Q. (2017). Solution-phase growth of organolead halide perovskite nanowires and nanoplates assisted by long-chain alkylammonium and solvent polarity. Mater. Lett. 206, 75-79. doi:10.1016/j.matlet.2017.06.113DOI
- [48]Liu, Z., Huang, S., Du, J., Wang, C., and Leng, Y. (2020). Advances in inorganic and hybrid perovskites for miniaturized lasers. Nanophotonics. 9(8), 2251–2272. doi:10.1515/nanoph-2019-0572DOI
- [49]Mao, L., Ke, W., Pedesseau, L., Wu, Y., Katan, C., Even, J., Wasielewski M. R., Stoumpos, C. C. and Kanatzidis, M.G. (2018). Hybrid Dion-Jacobson 2D Lead Iodide Perovskites. J. Am. Chem. Soc. 140(10), 3775-3783. doi:10.1021/jacs.8b00542DOI
- [50]Mao, L., Stoumpos, C. C. and Kanatzidis, M. G. (2019).Two-Dimensional Hybrid Halide Perovskites: Principles and Promises, J. Am. Chem. Soc. 141, 1171–1190. doi: 10.1021/jacs.8b10851DOI
- [51]Mas-Ballesté, R. , Gómez-Navarro, C. Gómez-Herrero J. and F. Zamora. (2011) 2D materials: to graphene and beyond Nanoscale, 3, 20-30. doi: 10.1039/CONR00323A
- [52]Mitzi, D. B. (2001). Templating and structural engineering in organic–inorganic perovskites. J. Chem. Soc., Dalton Trans. 1, 1-12. doi:10.1039/B007070JDOI
- [53]Mitzi, D. B., Wang, S., Feild, C. A., Chess, C. A. and Guloy, A. M. (1995). Conducting Layered Organic-inorganic Halides Containing <110>-Oriented Perovskite Sheets. Science. 267(5203), 1473-1476. doi:10.1126/science.267.5203.1473DOI
- [54]Naguib, M., Kurtoglu, M., Presser, V., Lu, J., Niu, J., Heon, M., Hultman, L., Gogotsi, Y., and Barsoum, M. W. (2011). Two Dimensional Nanocrystals Produced by Exfoliation of Ti₃AlC₂. Adv. Mater. 23(37), 4248-4253. doi:10.1002/adma.201102306DOI
- [55]Naguib, M., Mashtalir, O., Carle, J., Presser, V., Lu, J., Hultman, L., Gogotsi, Y., and Barsoum, M. W. (2012). Two-Dimensional Transition Metal Carbides. ACS Nano. 6(2), 1322-1331. doi:10.1021/nn204153hDOI
- [56]Niu, L., Zeng, Q., Shi, J., Cong, C., Wu, C., Liu, F., Zhou, J., Fu, W., Fu, Q., Jin, C., Yu, T., Liu, X. and Liu, Z. (2016). Controlled Growth and Reliable Thickness-Dependent Properties of Organic–Inorganic Perovskite Platelet Crystal, Adv. Funct. Mater. 26(29), 5263-5270. doi:10.1002/adfm.201601392DOI
- [57]Novoselov, K. S., Geim, A. K., Morozov, S. V., Jiang, D., Zhang, Y., Dubonos, S. V., Grigorieva, I. V. and Firsov, A. A. (2004) Electric Field Effect in Atomically Thin Carbon Films Science, 306, 666–669 doi: 10.1126/science.1102896DOI
- [58]Ortiz-Cervantes, C., Carmona-Monroy, P. and Solis-Ibarra, D. (2019). Two-Dimensional Halide Perovskites in Solar Cells: 2D or not 2D?. Chem. Sus. Chem, 12(8), 1560-1575. Doi:10.1002/cssc.201802992
- [59]Pazoki, M. and Edvinsson, T. (2018). Metal replacement in perovskite solar cell materials: chemical bonding effects and optoelectronic properties. Sustain. Energy Fuels. 2, 1430-1445. doi:10.1039/C8SE00143JDOI
- [60]Proppe, A. H., Elkins, M. H., Voznyy, O., Pensack, R. D., Zapata, F., Besteiro, L. V., Quan, L. N., Quintero-bermudez, R., Todorovic, P., Kelley, S. O., Govorov, A. O., Gray, S. K., Infante, I., Sargent, E. H. and Scholes, G. D. (2019). Spectrally resolved ultrafast exciton transfer in mixed perovskite Quantum Wells. J. Phys. Chem. Lett. 10(3), 419–426. doi:10.1021/acs.jpclett.9b00018DOI
- [62]Rothmann, M. U., Li, W., Zhu, Y., Bach, U., Spiccia, L., Etheridge, J., and Cheng, Y-B. (2017). Direct observation of intrinsic twin domains in tetragonal CH₃NH₃PbI₃. Nat. Commun. 8, 14547. doi:10.1038/ncomms14547DOI
- [63]Ruddlesden, S. N. and Popper, P. (1958). The compound Sr₃Ti₂O₇ and its structure._Acta Crystallogr. 11(1), 54-55. doi:10.1107/S0365110X58000128
- [64]Rühle, S. (2016). Tabulated values of the Shockley–Queisser limit for single junction solar cells. Sol. Energy. 130, 139-147. doi:10.1016/j.solener.2016.02.015DOI
- [65]Sha, T.-T., Xiong, Y.-A., Pan, Q., Chen, X.-G., Song, X.-J., Yao, J., Miao, S.-R., Jing, Z.-Y., Feng, Z.-J., You, Y.-M., and Xiong, R.-G. (2019). Fluorinated 2D lead iodide perovskite ferroelectrics. Adv. Mater. 31(30), 1901843. doi:10.1002/adma.201901843DOI
- [66]Shao, Y., Fang, Y., Li, T., Wang, Q., Dong, Q., Deng, Y., Yuan, Y., Wei, H., Wang, M., Gruverman, A., Shield, J., and Huang, J. (2016). Grain boundary dominated ion migration in polycrystalline organic–inorganic halide perovskite films. Energy Environ. Sci. 9, 1752-1759. doi:10.1039/C6EE00413J
- [67]Sheng, X., Chen, G., Wang, C., Wang, W., Hui, J., Zhang, Q., Yu, K., Wei, W., Yi, M., Zhang, M., Deng, Y., Wang, P., Xu, X., Dai, Z., Bao, J. and Wang, X. (2018). Polarized optoelectronics of CsPbX₃ (X = Cl, Br, I) perovskite nanoplates with tunable size and thickness. Adv. Funct. Mater. 28(19), 1800283. doi:10.1002/adfm.201800283DOI
- [68]Shin, C., Kim, K., Kim, J., Ko, W., Yang, Y., Lee, S., Jun, C. S., and Kim, Y. S. (2013). Fast, exact and non-destructive diagnoses of contact failures in nano-scale semiconductor device using conductive AFM. Sci. Rep. 3, 2088. doi:10.1038/srep02088DOI
- [70]Slavney, A. H., Smaha, R. W., Smith, I. C., Jaffe, A., Uyemaya, D., and Karunadasa, H. I. (2017). Chemical approaches to addressing the instability and toxicity of Lead–Halide perovskite absorbers. Inorg. Chem. 56(1), 46-55. doi:10.1021/acs.inorgchem.6b01336DOI
- [71]Spanopoulos, I., Hadar, I., Ke, W., Tu, Q., Chen, M., Tsai, H., He, Y., Shekhawat, G., Dravid, V. P., Wasielewski, M. R., Mohite, A. D., Stoumpos, C. C., and Kanatzidis, M. G. (2019). Uniaxial expansion of the 2D Ruddlesden–Popper perovskite family for improved environmental stability. J. Am. Chem. Soc. 141(13), 5518-5534. doi:10.1021/jacs.9b01327DOI
- [72]Stoumpos, C.C., Soe, C.M.M., Tsai, H., Nie, W., Blancon, J.-C., Cao, D.H., Liu, F., Traoré, B., Katan, C., Even, J., Mohite, A.D., and Kanatzidis, M. G. (2017). High members of the 2D Ruddlesdene-Popper halide perovskites: synthesis, optical properties, and solar cells of (CH₃(CH₂)₃NH₃)₂(CH₃NH₃)₄Pb₅I₁₆. Chem (Cell Press). 2(3), 427-440. doi:10.1016/j.chempr.2017.02.004DOI
- [73]Straus, D. B. and Kagan, C. R. (2018). Electrons, excitons, and phonons in two-dimensional hybrid perovskites: connecting structural, optical and electronic properties. J. Phys. Chem. Lett. 9(6), 1434–1447. doi:10.1021/acs.jpclett.8b00201DOI
- [74]Toda, S., Yanagita, N., Jokar, E., Diau, E. W. -G., and Shigeto, S. (2020). Inter- and Intragrain Inhomogeneity in 2D Perovskite Thin Films Revealed by Relative Grain Orientation Imaging Using Low-Frequency Polarized Raman Microspectroscopy. J. Phys. Chem. Lett. 11(10), 3871–3876. doi:10.1021/acs.jpclett.0c00992DOI
- [75]Tsai, H., Asadpour, R., Blancon, J. C., Stoumpos, C. C., Even, J., Ajayan, P. M., Kanatzidis, M. G., Alam, M. A., Mohite, A. D., and Nie, W. (2018). Design principles for electronic charge transport in solution- processed vertically stacked 2D perovskite quantum wells. Nat. Commun. 9, 2130. doi:10.1038/s41467-018-04430-2
- [76]Tyagi, P., Arveson, S. M., and Tisdale, W. A. J. (2015). Colloidal organohalide perovskite nanoplatelets exhibiting quantum confinement. Phys. Chem. Lett. 6(10), 1911-1916. doi:10.1021/acs.jpclett.5b00664DOI
- [77]Virdi, K. S., Kauffmann, Y., Ziegler, C., Ganter, P., Blaha, P., Lotsch, B. V., Kaplan, W. D., and Scheu, C. (2016). Band gap Extraction from Individual Two-Dimensional Perovskite Nanosheets Using Valence Electron Energy Loss Spectroscopy. J. Phys. Chem. C. 120(20), 11170–11179. doi:10.1021/acs.jpcc.6b00142DOI
- [78]Wang, K., Wu, C., Jiang, Y., Yang, D., Wang, K., and Priya, S. (2019). Distinct conducting layer edge states in two-dimensional (2D) halide perovskite. Sci. Adv. 5(7), eaau3241. doi: 10.1126/sciadv.aau3241DOI
- [79]Wang, P., Zhao, J., Wei, L., Zhu, Q., Xie, S., Liu, J., Meng, X., and Li, J. (2017). Photo-induced ferroelectric switching in perovskite CH₃NH₃PbI₃ films. Nanoscale. 9(11), 3806–3817. doi:10.1039/c6nr09310hDOI
- [81]Williams, O. F., Zhou, N., Hu, J., Ouyang, Z., Kumbhar, A., You, W., and Moran, A. M. (2019). Imaging excited state dynamics in layered 2D perovskites with transient absorption microscopy. J. Phys. Chem. A. 123(51), 11012–11021. doi:10.1021/acs.jpca.9b08852DOI
- [85]Yang, C. -H., Seidel, J., Kim, S. Y., Rossen, P. B., Yu, P., Gajek, M., Chu, Y. H., Martin, L. W., Holcomb, M. B., He, Q., Maksymovych, P., Balke, N., Kalinin, S. V., Baddorf, A. P., Basu, S. R., Scullin, M. L., and Ramesh, R. (2009). Electric modulation of conduction in multiferroic Ca-doped BiFeO3 films. Nat. Mater. 8(6), 485-493. doi:10.1038/nmat2432DOI
- [86]Yang, X., Zhang, X., Deng, J., Chu, Z., Jiang, Q., Meng, J., Wang, P., Zhang, L., Yin, Z., and You, J. (2018). Efficient green light-emitting diodes based on quasi-two-dimensional composition and phase engineered perovskite with surface passivation. Nat. Commun. 9, 570. doi:10.1038/s41467-018-02978-7DOI
- [89]Zhai, Y., Baniya, S., Zhang, C., Li, J., Haney, P., Sheng, C.-X., Ehrenfreund, E., and Vardeny, Z. V. (2017). Giant Rasbha splitting in 2D organic-inorganic halide perovskites measured by transient spectroscopies. Sci. Adv. 3(7), e1700704. doi:10.1126/sciadv.1700704DOI
- [91]Zhang, H., Liao, Q., Wu, Y., Zhang, Z., Gao, Q., Liu, P., Li, M., Yao, J., and Fu, H. (2018). 2D Ruddlesden–Popper perovskites microring laser array. Adv. Mater. 30(15), 1706186. doi:10.1002/adma.201706186DOI
- [92]Zheng, K., Chen, Y., Sun, Y., Chen, J., Chábéra, P., Schaller, R., Al-Marrі, M. J., Canton, S. E., Liang, Z., and Pullerits, T. (2018). Inter-phase charge and energy transfer in Ruddlesden-Popper 2D perovskites: critical role of the spacing cations. J. Mater. Chem. A. 6, 6244–6250. doi:10.1039/C8TA01518JDOI
- [93]Zhou, J., Chu, Y., and Huang, J. (2016). Photodetectors based on two-dimensional layer structured hybrid lead iodide perovskite semiconductors. ACS Appl. Mater. Interfaces. 8(39), 25660-25666. doi:10.1021/acsami.6b09489DOI
- [94]Zhou, Y., Sternlicht, H., and Padture, N. P. (2019). Transmission electron microscopy of halide Perovskite Materials and Devices. Joule. 3(3), 641–661. doi:10.1016/j.joule.2018.12.011DOI