betaFeedback

WorksPhysics and Astronomy

Nitrogen vacancy center in diamond-based Faraday magnetometer

Abstract

The nitrogen vacancy (NV) center in diamond is a versatile color center used for magnetometry, quantum computing, and quantum communications. In this article, using a single laser beam as a pump and probe, we measure the spin states of the NV center using the Faraday effect and use such measurements to develop a novel magnetic field sensor. Using the spin-state-dependent effect on the left and right circularly polarized light, we probe and confirm the existence of spin-orbit coupling in the NV center at room temperature. The sensitivity of our magnetometer is 350 350~nT/Hz\sqrt{Hz}, limited by the background produced by the laser trapped inside the diamond. We argue that by using an optical cavity and a high-purity diamond, sensitivities in the femtotesla level can be achieved.

The ability to detect weak magnetic fields and their directions finds applications in fundamental physics including measuring the permanent electric dipole moments of electrons and neutrons [1, 2, 3], magnetic navigation [4, 5], planetary exploration [6, 7], magnetocardiography of our hearts [8] and magnetoencephalography of our brains [9, 10]. One of the most sensitive vector magnetometers is an optically pumped magnetometer (OPM) [11, 12, 13] with a sensitivity of 160 attotesla [11]. Such a sensor uses the Faraday effect-based detection scheme, operates in a magnetically shielded environment, and can resolve magnetic fields with a centimeter-scale resolution (important in biomedical imaging [8, 9, 10]). Scalar OPMs can operate in ambient conditions but suffer from heading errors [4, 13]. Superconducting quantum interference devices (SQUIDs) are another class of highly sensitive magnetometers that provide femtotesla-level sensitivity [14], but they require cryogenic cooling.

The nitrogen vacancy center in diamond is a versatile atom-like system [15], used for magnetometry [16, 17, 18, 19, 20], and has been proposed for quantum computing [21] and quantum gravity experiments [22]. The NV center-based magnetometers [17, 18, 19, 20] operate in ambient conditions, are immune to heading errors, and can spatially resolve magnetic fields with a millimeter-scale resolution [20, 23]. However, the sensitivity of current NV magnetic field sensors [17, 18, 19, 20] is on the order of a picotesla and not suitable for demanding applications such as magnetoencephalography. One of the main limitations of NV magnetometers is their detection scheme, which uses the NV spin-state-dependent photoluminescence (PL), a spin state destructive measurement system. Collecting PL emitted in all directions by NV centers is challenging. Detection schemes that can measure the spin states of NV centers non-destructively, as well as repeatedly and without relying on photoluminescence, would benefit magnetometry, quantum computing, and quantum gravity experiments.

In this article, we measure the spin states of NV centers using the Faraday effect, a non-destructive measurement scheme [24, 25], and using such measurements develop a magnetometer with the potential to reach femtotesla sensitivity. We investigate different optical transition dipole selection rules using linearly and circularly polarized light and confirm the existence of spin-orbit coupling in NV centers at room temperature.

The nitrogen-vacancy center in diamond consists of a substitutional nitrogen atom and an adjacent vacancy in the diamond lattice. Figure 1a shows an NV center oriented along the [111] crystallographic axis. The diamond used in our experiment is a single crystal {111} cut 2 × 2 × 2 mm³ Type 1b high-pressure high temperature (HPHT) single-crystal synthetic diamond, and contains 0.220 ppm NV centers and 54 ppm substitutional nitrogen. For magnetometry, we apply a homogeneous dc magnetic field (BB) parallel to the [111] axis of the diamond. The ground state manifold (3A2{}^3A_2) of an NV center is an orbital-singlet spin-triplet (S=1S = 1, ms=0m_s = 0, ±1\pm1) state with zero orbital angular momentum, while the excited-state manifold is an orbital doublet and has orbital angular momenta of ±1\pm1 [26, 27]. As we use an ensemble of NV centers, strain is inevitable [15, 27, 28, 29, 30], which splits the excited state into two branches: ExE_x (A1A_1, A2A_2, ExE_x) and EyE_y (E1E_1, E2E_2, EyE_y). At relatively low strain the A1A_1, A2A_2, E1E_1, E2E_2 and EyE_y states are spin-orbital entangled states e.g., A2=∣E+⟩⊗∣−1⟩+∣E−⟩⊗∣+1⟩A_2 = |E_+\rangle\otimes|-1\rangle+ |E_-\rangle\otimes|+1\rangle [26, 27], where E±E_\pm is the excited state orbital angular momentum and ∣±1⟩|\pm1\rangle represent spin states for ms=±1m_s = \pm1. Ex,yE_{x,y} states only couple to the ms=0m_s = 0 state of the ground state manifold by absorbing linearly polarized light, while the other four states can be excited from the ms=±1m_s = \pm1 states via circularly polarized light.

Figure 1. a) The nitrogen-vacancy (NV) center in diamond and its energy level diagram at low temperature. Here, an NV center oriented along the [111] direction has been shown. A dc magnetic field BB is applied along the [111] crystallographic direction for lifting the degeneracy of the NV center’s ground state manifold. b) A schematic of our experimental setup. A green laser (532 nm) is used for exciting the NV centers from their ground state manifold (3A2^{3}A_{2}) to the excited state manifold (3E^{3}E). Before interacting with the NV centers, the green laser passes through a linear polarizer and a half/quarter wave plate (WP). The axis of the polarizer is parallel to the xx axis of the laboratory frame. A mirror located after the diamond sends back the green laser through the diamond for a second time. A pick-off mirror is used to collect the retroreflected laser beam. Other optical components of the experiment are: MM - mirror, DD - photodiode, PBS - polarizing beam splitter, and λ/2\lambda/2 - half waveplate. Components within the dotted box make the balanced polarimeter. c) Photoluminescence as a function of the angle of the half-wave plate located before the diamond.

A schematic of our experimental setup is shown in Figure 1b. The diamond is oriented such that the [111] crystallographic direction is along the zz-axis. A linearly polarized green laser (532 nm) propagating along the zz axis non-resonantly excites the nitrogen-vacancy center from the ground state manifold to the excited state manifold and eventually spin polarizes the NV centers to the ms=0m_s = 0 state [15]. Due to the ensemble nature of our experiment, we excite NV centers of all orientations along the path of our excitation beam. As well as using the green laser as an NV center excitation source, we use it as a probe to measure the spin states of NV centers via the Faraday effect (FE). To excite more NV centers and enhance the Faraday effect, the green laser is retroreflected and picked up using a pickoff mirror. The double-passed green laser is then inputted to a balanced polarimeter composed of a half-wave plate, a polarizing beam splitter, and a balanced photodetector consisting of two identical photodiodes [1, 31]. The retroreflected green laser is also used for detecting absorption detected magnetic resonance (ADMR) [32]. In this case, the retroreflected green laser is directly inputted to one of the photodiodes of the balanced detector, while the other photodiode receives a fraction of the green laser that has not interacted with the diamond. Additionally, photoluminescence emitted by NV centers is detected using a detector placed along the xx axis.

In our first experiment, we measure PL as we rotate the plane of polarization of the green laser using a half-wave plate placed immediately after the polarizer and no microwaves are used. The axis of the polarizer is parallel to the xx axis, which we use as a reference. Two orthogonal electric dipoles associated with the NV centers along the [111] axis are in the x−yx-y plane while the remaining six dipoles belonging to the other NV centers are in planes that make an angle ≈71∘\approx71^\circ with the x−yx-y plane [33]. Figure 1c shows the results of our measurements [28, 34]. Due to the non-resonant and ensemble nature of our experiment, identifying the orientations of 3Ex^{3}E_x and 3Ey^{3}E_y unambiguously is challenging. Nevertheless, taking into account the dipole radiation pattern, we fit a function of the form A−Bcos⁡2α−Ccos⁡(2α−4ϕ)A-B\cos2\alpha-C\cos(2\alpha-4\phi) and retrieve ϕ\phi - the angle between the xx axis and 3Ex^{3}E_x. The angle between the xx axis and the laser polarization is denoted by α\alpha. From fit we find ϕ≈72∘\phi\approx72^\circ indicating that 3Ex^{3}E_x and 3Ey^{3}E_y are located at ϕ=72∘\phi=72^\circ and ϕ=−18∘\phi=-18^\circ, respectively. Note that because of the position of our PL detector and the small angle over which we collect PL, the total photoluminescence is independent of the orientations of other dipoles (see supplementary information).

Figure 2a shows the raw photoluminescence (red) and the same when detected using a lock-in amplifier (blue) as a function of microwave frequency. The polarization of the laser is parallel to the xx axis (α=0\alpha=0). Due to B∥[111]B \parallel[111], the ODMRs associated with the NV centers along the [111] crystallographic direction appear at (D+γmsB)/2π(D+\gamma m_s B)/2\pi while the ODMRs of the remaining NV centers cluster at (D+γmsBcos⁡θ)/2π(D+\gamma m_s B\cos\theta)/2\pi with θ≈109∘\theta\approx109^\circ. The ODMRs at (D+msγB)/2π(D+m_s\gamma B)/2\pi are stronger than others due to the orthogonality of the microwave magnetic field with these centers, allowing efficient excitation. Figure 2b shows ADMR [32]. The polarities of all ADMR peaks are identical but are opposite to those due to PL.

Figure 2. Magnetic resonances a) Photoluminescence-based optically detected magnetic resonance (ODMR) when the angle between the linear polarizer and the half-wave plate after it is zero ((α=0\alpha=0). The blue data uses a lock-in amplifier while the red data do not. b) The green laser absorption detected magnetic resonance (ADMR) c) The Faraday detected magnetic resonance (FDMR) for α=0\alpha=0 & 72∘72^\circ.

Figure 2c shows the output of the lock-in amplifier when the retroreflected green laser and the balanced polarimeter are in use. Four peaks are visible, which we call the Faraday detected magnetic resonance (FDMR). The two peaks belonging to the ms=0→−1m_s=0 \to-1 transitions at lower microwave frequencies are stronger than those due to the ms=0→+1m_s=0 \to+1 transitions for α=0\alpha=0 (blue). For comparison, we also show data when the polarization of the laser is parallel to the 3Ex{}^3E_x dipole (α=72∘\alpha=72^\circ) (red). The peaks belonging to the ms=0→+1m_s=0 \to+1 transitions are now dominant. Most importantly, in both cases, the polarities of the ms=0→−1m_s=0 \to-1 transitions and the ms=0→+1m_s=0 \to+1 transitions are opposite. This contrasts with ADMR and ODMR, which have peaks of the same polarities. Linearly polarized light is composed of left (σ^+\hat{\sigma}_+) and right (σ^−\hat{\sigma}_-) circularly polarized light i.e., x^=(σ^++σ^−)/2\hat{x}=(\hat{\sigma}_+ + \hat{\sigma}_-)/\sqrt{2} and y^=−i(σ^+−σ^−)/2\hat{y}=-i(\hat{\sigma}_+ - \hat{\sigma}_-)/\sqrt{2}. When α=72∘\alpha=72^\circ, we only excite the 3Ex{}^3E_x dipole due to the optical selection rules [27]. NV centers in the ms=−1m_s=-1 state add a phase to the σ^+\hat{\sigma}_+ component of the linearly polarized light, keeping the σ^−\hat{\sigma}_- component intact [24, 35, 36]. The spin state-dependent phase rotates the plane of polarization of linearly polarized light in the opposite direction, giving rise to FDMR peaks of opposite polarities. We note that in our Faraday measurements, the 3Ey{}^3E_y dipole appears at α=0\alpha=0 instead of α=−18∘\alpha=-18^\circ predicted by the fluorescence measurement (Figure 1c). This might be due to the strain-induced reorientation of the dipole.

Figure 3 shows the peak-to-peak amplitude of FDMR as a function of the angle (α\alpha) between the fast axis of a quarter waveplate (532 nm) and the axis of the linear polarizer for optical transitions from the ms=±1m_s=\pm1 states in the ground state manifold. In accord with the optical selection rules, as the light becomes more and more σ+\sigma_+ polarized, the strength of the FDMR due to ms=−1m_s=-1 reaches its peak while that due to ms=+1m_s=+1 reaches its minimum. The situation changes when light becomes σ−\sigma_- polarized and the FDMR due to ms=+1m_s=+1 reaches its maximum while that due to ms=−1m_s=-1 is minimized. This demonstrates the existence of spin-orbit coupling at room temperature. We get a contrast of 60% between the maximum and minimum strength of the FDMR peaks instead of the ideal 100%. This might be due to the ensemble nature of our experiment and the experimental imperfections including light not being completely circularly polarized. Experimental imperfections might also explain the slight offset (12∘12^\circ) in reaching the minimum

Figure 3. The peak-to-peak amplitude of FDMR as a function of quarter-waveplate angle α\alpha when the ms=0→−1m_s=0 \to-1 (blue) and ms=0→+1m_s=0 \to+1 (red) transitions are pumped using microwaves. Solids lines are fits of the form A+Bsin⁡(4α+C)A+B\sin(4\alpha+C).

(maximum) strength of FDMR peaks (Figure 3) at 57∘57^\circ instead of 45∘45^\circ. The broader question, however, is which of the possible transitions between the ground and excited states are responsible for the behavior we see in Figure 3. The selection rules [27] indicate that when light is σ+\sigma_+ polarized, ms=−1→{A1,A2}m_s=-1 \to\{A_1,A_2\} and ms=+1→{E1,E2}m_s=+1 \to\{E_1,E_2\} transitions are allowed by applying FDMR maxima for both ms=±1m_s=\pm1. Experimentally, we find that only FDMR associated with ms=−1m_s=-1 is maximized. It might be that the selection rules are not completely followed at room temperature, and the oscillator strengths of these transitions are unequal. The latter point might also explain the often weak and fluctuating nature of the FDMRs owing to the ms=+1m_s=+1 state that we measure. It might also be the case that due to thermal averaging at room temperature [37], not all transitions demonstrated at low temperature [26] are affected equally and only the ms=±→A2m_s=\pm\to A_2 transition survives, which is the highest energy level in the 3E{}^3E manifold and robust against strain [15, 26, 27]. The ms=±1→A2m_s=\pm1 \to A_2 transition is then responsible for the data shown in Figure 3.

The rotation angle ϕ\phi of the plane of polarization of the linearly polarised green light after it has travelled through the diamond can be found from the balanced detector signal [1] ϕ≈ΔP2P\phi\approx\frac{\Delta P}{2P}, where PP is the input power to the polarimeter, ΔP\Delta P is the difference signal of the balanced detector and ∣ϕ∣≪π/4|\phi| \ll\pi/4 is assumed. The input power to the detector can be directly measured. However, due to the smallness of ϕ\phi, ΔP\Delta P is small and often perturbed by the laser noise and drift. To increase the signal-to-noise ratio, we use a lock-in amplifier. The output of the lock-in amplifier is appropriately calibrated and subsequently integrated to find ϕ\phi. Figure 4a shows the raw output of the lock-in amplifier while panel b shows ϕ\phi as a function of the microwave frequency when the ms=0→−1m_s = 0 \to-1 transition belonging to the [11] is pumped. On microwave resonance, where the highest number of NV centers are in the ms=−1m_s = -1 state, the plane of polarization of the green laser is rotated by 6 micro radians. When the ms=0→+1m_s = 0 \to+1 transition is pumped, the plane of polarization of the green laser is rotated by the same amount but in the opposite direction.

Figure 4. a) Lock-in amplifier output as a function of the microwave frequency when the ms=0→−1m_s = 0 \to-1 transition is pumped. b) The plane of polarization rotation angle corresponding to the FDMR signal shown in a (see text for more information).

The plane of polarization rotation angle ϕ\phi can be calculated from the perspective of circular birefringence [1, 31]. In particular, when the ms=0→−1(+1)m_s = 0 \to-1(+1) transition is pumped using microwaves, the NV centers become spin polarized i.e., ⟨Sz⟩<0(>0)\langle S_z \rangle< 0 (> 0), and the left and right circularly polarized light encounters different indices of refraction. This difference in index of refraction rotates the plane of polarization of the linearly polarized light by

ϕ=2ntkLρnRe⁡{ζ}⟨Sz⟩z^⋅k^,(1)\phi= 2n_t k L \rho_n \operatorname{Re}\{\zeta\}\langle S_z\rangle\hat{z}\cdot\hat{k}, \tag*{(1)}

where ntn_t is the number of times probe light of wavelength λ\lambda travels through the diamond of length LL, k=2π/λk = 2\pi/\lambda, ρn\rho_n is the number density of NV centers, ζ=refsc2L(ν)4πν\zeta= \frac{r_e f_s c^2 L(\nu)}{4\pi\nu} with cc being the speed of light and rer_e being the classical electron radius. fsf_s and L(ν)=(ν−ν0)/(ν−ν0+iΓ)L(\nu) = (\nu-\nu_0)/(\nu-\nu_0+i\Gamma) are the oscillator strength and the absorption spectral profile of an NV center with ν=c/λ\nu= c/\lambda being the laser frequency, ν0\nu_0 is the optical resonance frequency of the NV center and Γ\Gamma is the linewidth of the optical resonance. ⟨Sz⟩=∑smsPs\langle S_z\rangle= \sum_s m_sP_s is the average spin polarization of NV centers along the zz axis with PsP_s being the probability of an NV center being in the ss state. With the theoretical and experimental values of ϕ\phi at hand, the number of NV centers contributing to the Faraday effect can be estimated. The absorption profile of NV centers is broad and is not well defined at room temperature. For our estimation we consider the NV center to have a Lorentzian absorption profile with Γ≈1014\Gamma\approx10^{14} Hz (≈98\approx98 nm) and ν0=5.4×1014\nu_0 = 5.4 \times10^{14} Hz (555 nm) [38, 39], fs=0.02f_s = 0.02 [40]. From the rate-equations-based simulation [29], for our microwave and laser power, we find ≈36\approx36 (1)% of the NV population is in the ms=−1(+1)m_s = -1(+1) state. The net spin polarization contributing to the Faraday effect is ⟨Sz⟩=−0.35\langle S_z\rangle= -0.35. With ϕ=6×10−6\phi= 6 \times10^{-6} radians at resonance (Figure 4b) and taking into account that we are only exciting ≈1%\approx1\% of the NV centers due to the limited amount of green laser power available (see supplementary information), we get ρn=1.1×1022 m−3\rho_n = 1.1 \times10^{22}\ \mathrm{m}^{-3}. From our EPR measurements, the density of NV centers is (4.01±0.36)×1022 m−3(4.01 \pm0.36) \times10^{22}\ \mathrm{m}^{-3}. Considering the uncertainty in different parameters, including the NV absorption profile and oscillator strength, ρn\rho_n found from ϕ\phi is reasonable. Using this ρn\rho_n and taking the laser illuminated volume of the diamond as that of a cylinder of diameter 1 mm and length L=2L = 2 mm, we calculate the number of NV centers interacted with the green probe beam is ns=2.1×1010n_s = 2.1 \times10^{10}. In other words, a single photon has interacted with 250 centers while traveling through the diamond.

The effect of the spins on the probe light’s plane of polarization can be used for magnetometry [1, 12] and to perform quantum nondemolition measurements [24, 25, 41, 42, 43]. Here, we develop a magnetometer. To perform magnetometry, we use the ms=0→−1m_s = 0 \to-1 transition and continuously drive it using resonant microwaves. The green laser power after the polarizer was 1.1 W while the microwave power was set to 33 dBm at the input of the antenna. Magnetic fields to be detected shift the resonance frequency of the ms=0→ms=−1m_s = 0 \to m_s = -1 transition via the Zeeman effect. This changes the NV center population in the ms=−1m_s = -1 state. This, in turn, changes ϕ\phi, which then perturbs the balance of the balanced detector. The lock-in amplifier, therefore, provides a modified voltage signal. With an appropriate calibration, the unknown magnetic field can be found from the lock-in amplifier (LIA) signal. Figure 5 shows the Fourier transforms of the calibrated outputs of the lock-in amplifier. Between 10 and 200 Hz, our magnetometer has a sensitivity of 350 nT/Hz\sqrt{\mathrm{Hz}}. The spin-projection-limited minimum detectable magnetic field [1, 12, 18] is

Figure 5. Sensitivity of the Faraday effect-based magnetometer. The blue line shows the Fourier transform of the lock-in amplifier output after appropriate calibration.

ΔB=1γnsT2∗t,(2)\Delta B = \frac{1}{\gamma\sqrt{n_sT_2^*t}}, \tag*{(2)}

where nsn_s is the number of the NV center that contributed to the Faraday effect, T2∗T_2^* is the intrinsic spin coherence time and tt is the measurement time. The intrinsic spin coherence time of our diamond is T2∗=21T_2^* = 21 ns. Substituting nsn_s, T2∗T_2^* and t=0.5t = 0.5 s in (2), we get ΔB=1.7×10−12\Delta B = 1.7 \times10^{-12} T. This is significantly better than what we have measured. When we set the frequency of our microwave source away from the resonance, the noise floor remains the same, indicating that we are limited by non-magnetic noise. When we separately measure the laser noise with an appropriate calibration, the noise floor is significantly lower. The temperature of our diamond increases by 30 K, measured using the shift in ODMR frequency [44], from room temperature at the microwave and laser power used. This is unlikely to cause a significant issue. A potential noise source is the green laser that gets trapped inside the diamond due to diamond’s high refractive index [45]. After spending some time inside the diamond, the trapped light with arbitrary phase eventually exits the diamond, travels with the retroreflected beam, and interferes, causing a white noise-like background. By covering the diamond with anti-reflection coatings, this can be mitigated, which we aim to do in the future.

The sensitivity of our magnetometer can be improved in several ways. The laser power immediately before the PBS (Figure 1b) is 120 mW. This is significantly higher than our existing balanced detector can take. So we use a neutral density filter to attenuate the power. By using photodiodes capable of taking extra laser power, the sensitivity can be improved straightforwardly. Another major area of improvement is to use a high-quality chemical vapor deposition (CVD) diamond, which has superior NV spin properties [20, 45]. For example, T2∗=14T_2^* = 14 μ\mus has been measured [45]. Additionally, the sensitivity can also be improved either by addressing more NV centers using extra green laser power or by increasing the density of the nitrogen-vacancy centers [20].

The Faraday effect is non-reciprocal, meaning that each time light interacts with the spins of NV centers, its plane of polarization gets rotated by another ϕ\phi [46, 47]. When we do not use a double pass geometry, the sensitivity of our magnetometer is about ≈1.5\approx1.5 μ\muT/Hz\sqrt{\mathrm{Hz}}. This implies that a substantial gain can be made by using an optical cavity [41, 46]. By using a separate probe laser and a cavity around the diamond, the interaction between the probe light and the NV centers can be significantly enhanced. The cavity could be formed using two independent mirrors or by coating the diamond surfaces with mirror coating. When two mirrors are used to form the cavity, the surfaces of the diamond can be coated with an antireflection coating to enhance cavity finesse [19]. Cavities formed by directly coating the surfaces of the diamond might be more stable due to their monolithic nature. Such cavities might also be preferable for applications requiring high spectral resolutions, such as biomedical imaging, since the dimensions of such a cavity will be the size of the diamond itself. The number of times, ntn_t, probe light bounces back and forth inside the cavity and thus interacts with the NV centers is determined by the cavity finesse (FF) or the reflectivity rfr_f of the cavity mirrors with F=1/(1−rf)F = 1/(1-r_f). Assuming rf=99.99%r_f = 99.99\%, a cavity finesse of 10410^4 is achievable [48, 49]. Such a cavity will increase the sensitivity by two orders of magnitude. The maximum time for which light can be confined within the cavity to enhance sensitivity is the ≤T2∗\leq T_2^* time of the nitrogen-vacancy centers.

In our current experiment, we continuously pump the NV centers using a green laser and resonant microwaves. This creates a competition between the spin polarization to the ms=0m_s = 0 state by the green laser and the microwave excitation to the ms=−1m_s = -1 state. This reduces the interaction time between probe light and the spin. This can be avoided by implementing pulsed operation in which a green laser pulse is used to initialize NV centers to the ms=0m_s = 0 state and subsequently, a microwave π\pi pulse is applied to excite the spins to the ms=−1m_s = -1 state. This will allow probe light to interact with the spins more efficiently and thus enhance the sensitivity. The performance of our magnetometer can also be improved by driving the hyperfine transitions [20, 45]. With all enhancements incorporated, NV Faraday magnetometers could achieve on the order of a femtotesla sensitivity.

In conclusion, we have demonstrated the Faraday effect at room temperature and used this effect for magnetometry. To our knowledge, this is the first time the Faraday effect has been used to develop a magnetometer using NV centers in diamond. Our measurements also show that the spin-orbit coupling in NV centers exists at room temperature, in contrast with the earlier predictions [37]. At present, the sensitivity of our Faraday magnetometer is limited by the background caused by the trapped excitation laser, which can be mitigated using anti-reflection coatings. Using a better diamond, laser, and a cavity, sensitivities in the femtotesla level seem viable. Our experiment also opens the door to quantum non-demolition measurements of NV center spin states required in some applications [50]. Finally, our Faraday-effect-based magnetometer is amenable to different techniques such as gradiometry developed by the optically pumped magnetometer (OPM) community [1, 13]. The benefit of a solid state sensor combined with the techniques developed for OPMs can be advantageous for developing new technological platforms from biomedical imaging to magnetic navigation to fundamental physics.

Acknowledgment: We acknowledge our illuminating discussions with Prof. D. Budker. His insightful comments and suggestions have strengthen this manusript significantly. We also acknowledge our discusions with V. Acosta, P. Hemmer and K. Pauli. AR acknowledges the financial support of Warwick Innovations and an EP-SRC IAA grant.

References

References

  1. [1]D. Budker, W. Gawlik, D. F. Kimball, S. M. Rochester, V. V. Yashchuk, and A. Weis, Resonant nonlinear magneto-optical effects in atoms, Rev. Mod. Phys. 74, 1153 (2002).DOI
  2. [2]S. A. Murthy, D. Krause, Z. L. Li, and L. R. Hunter, New limits on the electron electric dipole moment from cesium, Phys. Rev. Lett. 63, 965 (1989).pubmed.ncbi.nlm.nih.gov/10041234
  3. [3]C. Abel, S. Afach, N. J. Ayres, G. Ban, G. Bison, K. Bodek, V. Bondar, E. Chanel, P.-J. Chiu, C. B. Crawford, Z. Chowdhuri, M. Daum, S. Emmenegger, L. Ferraris-Bouchez, M. Fertl, D. Fränke, W. C. Griffith, Z. D. Grujić, L. Hayen, V. Hélaine, N. Hild, M. Kasprzak, Y. Kermaidic, K. Kirch, P. Knowles, H.-C. Koch, S. Komposch, P. A. Koss, A. Kozela, J. Krempel, B. Lauss, T. Lefort, Y. Lemiére, A. Leredde, A. Mtchedlishvili, P. Mohanmurthy, M. Musgrave, O. Naviliat-Cuncic, D. Pais, A. Pazgalev, F. M. Piegsa, E. Pierre, G. Pignol, P. N. Prashanth, G. Qué méner, M. Rawlik, D. Rebreyend, D. Ries, S. Roccia, D. Rozpedzik, P. Schmidt-Wellenburg, A. Schnabel, N. Severijns, R. T. Dinani, J. Thorne, A. Weis, E. Wursten, G. Wyszynski, J. Zejma, and G. Zsigmond, Optically pumped cs magnetometers enabling a high-sensitivity search for the neutron electric dipole moment, Phys. Rev. A 101, 053419 (2020).DOI
  4. [4]A. J. Canciani, Magnetic navigation on an f-16 aircraft using online calibration, IEEE Trans. Aerosp. Electron. Syst. 58, 420 (2022).DOI
  5. [5]N. R. Claussen, L. D. Le, R. Ashton, K. A. Cespedes, A. Patel, L. L. Williams, B. O. Miller, and J. Searcy, Magnetic Navigation for GPS-Denied Airborne Applications, Tech. Rep. (Sandia National Lab. (SNL-NM), Albuquerque, NM (United States), 2020).DOI
  6. [6]H. Korth, K. Strohbеhn, F. Tejada, A. G. Andreou, J. Kitching, S. Knappe, S. J. Lehtonen, S. M. London, and M. Kafel, Miniature atomic scalar magnetometer for space based on the rubidium isotope 87rb, J. Geophys. Res. Space Physics 121, 7870 (2016).pubmed.ncbi.nlm.nih.gov/27774373
  7. [7]T. J. Sabaka, R. H. Tyler, and N. Olsen, Extracting ocean-generated tidal magnetic signals from swarm data through satellite gradiometry, Geophys. Res. Lett. 43, 3237 (2016).DOI
  8. [8]D. Brinsinda, P. Fenici, and R. Fenici, Clinical magnetocardiography: the unshielded bet—past, present, and future, Front. Cardiovasc. Med. 10, 1232882 (2023).
  9. [9]M. Hämäläinen, R. Hari, R. J. Ilmoniemi, J. Knuutila, and O. V. Lounasmaa, Magnetoencephalography—theory, instrumentation, and applications to noninvasive studies of the working human brain, Rev. Mod. Phys. 65, 413 (1993).DOI
  10. [10]M. J. Brookes, J. Leggett, M. Rea, R. M. Hill, N. Holmes, E. Boto, and R. Bowtell, Magnetoencephalography with optically pumped magnetometers (opm-meg): the next generation of functional neuroimaging, Trends Neurosci. 45, 621 (2022).DOI
  11. [11]H. B. Dang, A. C. Maloof, and M. V. Romalis, Ultrahigh sensitivity magnetic field and magnetization measurements with an atomic magnetometer, Appl. Phys. Lett. 97, 151110 (2010).DOI
  12. [12]I. K. Kominis, T. W. Kornack, J. C. Allred, and M. V. Romalis, A subfemtotesla multichannel atomic magnetometer, Nature 422, 596 (2003).pubmed.ncbi.nlm.nih.gov/12686995
  13. [13]A. Fabricant, I. Nokovа, and G. Bison, How to build a magnetometer with thermal atomic vapor: a tutorial, New J. Phys. 25, 025001 (2023).
  14. [14]M. Buchner, K. Höfler, B. Henne, V. Ney, and A. Ney, Tutorial: Basic principles, limits of detection, and pitfalls of highly sensitive squid magnetometry for nanomagnetism and spintronics, J. Appl. Phys. 124, 161101 (2018).DOI
  15. [15]M. W. Doherty, N. B. Manson, P. Delaney, F. Jelezko, J. Wrachtrup, and L. C. Hollenberg, The nitrogen-vacancy colour centre in diamond, Phys. Rep. 528, 1 (2013).DOI
  16. [16]J. F. Barry, J. M. Schloss, E. Bauch, M. J. Turner, C. A. Hart, L. M. Pham, and R. L. Walsworth, Sensitivity optimization for nv-diamond magnetometry, Rev. Mod. Phys. 92, 015004 (2020).DOI
  17. [17]T. Wolf, P. Neumann, K. Nakamura, H. Sumiya, T. Ohshima, J. Isoya, and J. Wrachtrup, Subpicotesla diamond magnetometry, Phys. Rev. X 5, 041001 (2015).
  18. [18]V. M. Acosta, E. Bauch, A. Jarmola, L. J. Zipp, M. P. Ledbetter, and D. Budker, Broadband magnetometry by infrared-absorption detection of nitrogen-vacancy ensembles in diamond, Appl. Phys. Lett. 97, 174104 (2010).DOI
  19. [19]G. Chatzidrosos, A. Wickenbrock, L. Bougas, N. Leefer, T. Wu, K. Jensen, Y. Dumeige, and D. Budker, Miniature cavity-enhanced diamond magnetometer, Phys. Rev. Appl. 8, 044019 (2017).DOI
  20. [20]S. Graham, A. Rahman, L. Munn, R. Patel, A. Newman, C. Stephen, G. Colston, A. Nikitin, A. Edmonds, D. Twitchen, M. Markham, and G. Morley, Fiber-coupled diamond magnetometry with an unshielded sensitivity of 30pT/√hz, Phys. Rev. Appl. 19, 044042 (2023).
  21. [21]S. Pezzagna and J. Meijer, Quantum computer based on color centers in diamond, Appl. Phys. Rev. 8, 011308 (2021).DOI
  22. [22]S. Bose, A. Mazumdar, G. W. Morley, H. Ulbricht, M. Toros, M. Paternostro, A. A. Geraci, P. F. Barker, M. S. Kim, and G. Morley, Spin entanglement witness for quantum gravity, Phys. Rev. Lett. 119, 240401 (2017).DOI
  23. [23]T. Wolf, P. Neumann, K. Nakamura, H. Sumiya, T. Ohshima, J. Isoya, and J. Wrachtrup, Subpicotesla diamond magnetometry, Phys. Rev. X 5, 041001 (2015).
  24. [24]B. B. Buckley, G. D. Fuchs, L. C. Bassett, and D. D. Awschalom, Spin-light coherence for single-spin measurement and control in diamond, Science 330, 1212 (2010).DOI
  25. [25]V. Shah, G. Vasilakis, and M. V. Romalis, High bandwidth atomic magnetometry with continuous quantum nondemolition measurements, Phys. Rev. Lett. 104, 013601 (2010).pubmed.ncbi.nlm.nih.gov/20366362
  26. [26]E. Togan, Y. Chu, A. S. Trifonov, L. Jiang, J. Maze, L. Childress, M. V. G. Dutt, A. S. Sørensen, P. R. Hemmer, A. S. Zibrov, and M. D. Lukin, Quantum entanglement between an optical photon and a solid-state spin qubit, Nature 466, 730 (2010).
  27. [27]J. R. Maze, A. Gali, E. Togan, Y. Chu, A. Trifonov, E. Kaxiras, and M. D. Lukin, Properties of nitrogen-vacancy centers in diamond: the group theoretic approach, New J. Phys. 13, 025025 (2011).DOI
  28. [28]K.-M. C. Fu, C. Santori, P. E. Barclay, L. J. Rogers, N. B. Manson, and R. G. Beausoleil, Observation of the dynamic jahn-teller effect in the excited states of nitrogen-vacancy centers in diamond, Phys. Rev. Lett. 103, 256404 (2009).
  29. [29]N. B. Manson, J. P. Harrison, and M. J. Sellars, Nitrogen-vacancy center in diamond: Model of the electronic structure and associated dynamics, Phys. Rev. B 74, 104303 (2006).DOI
  30. [30]A. Batalov, V. Jacques, F. Kaiser, P. Siyushev, P. Neumann, L. J. Rogers, R. L. McMurtrie, N. B. Manson, F. Jelezko, and J. Wrachtrup, Low temperature studies of the excited-state structure of negatively charged nitrogen-vacancy color centers in diamond, Phys. Rev. Lett. 102, 195506 (2009).pubmed.ncbi.nlm.nih.gov/19518973
  31. [31]V. Shah and M. V. Romalis, Spin-exchange relaxation-free magnetometry using elliptically polarized light, Phys. Rev. A 80, 013416 (2009).arxiv.org/abs/0903.2447
  32. [32]S. Ahmadi, H. A. R. El-Ella, A. M. Wojciechowski, T. Gehring, J. O. B. Hansen, A. Huck, and U. L. Andersen, Nitrogen-vacancy ensemble magnetometry based on pump absorption, Phys. Rev. B 97, 024105 (2018).
  33. [33]P. Reuschel, M. Agio, and A. M. Platae, Vector magnetometry based on polarimetric optically detected magnetic resonance, Adv Quantum Technol. 5, 2200077 (2022).
  34. [34]R. J. Epstein, F. M. Mendoza, Y. K. Kato, and D. D. Awschalom, Anisotropic interactions of a single spin and dark-spin spectroscopy in diamond, Nat. Phys. 1, 94 (2005).DOI
  35. [35]C. Y. Hu, A. Young, J. L. O’Brien, W. J. Munro, and J. G. Rarity, Giant optical faraday rotation induced by a single-electron spin in a quantum dot: Applications to entangling remote spins via a single photon, Phys. Rev. B 78, 085307 (2008).DOI
  36. [36]M. Atatüre, J. Dreiser, A. Badolato, and A. Imamoglu, Observation of faraday rotation from a single confined spin, Nat. Phys. 3, 101 (2007).DOI
  37. [37]L. J. Rogers, R. L. McMurtrie, M. J. Sellars, and N. B. Manson, Time-averaging within the excited state of the nitrogen-vacancy centre in diamond, New J. Phys. 11, 063007 (2009).DOI
  38. [38]G. Davies, M. F. Hamer, and W. C. Price, Optical studies of the 1.945 ev vibronic band in diamond, Proc. R. Soc. Lon. A 348, 285 (1976), https://royalsocietypublishing.org/doi/pdf/10.1098/rspa.1976.0039.DOI
  39. [39]E. Fraczek, V. G. Savitski, M. Dale, B. G. Breeze, P. Diggle, M. Markham, A. Bennett, H. Dhillon, M. E. Newton, and A. J. Kemp, Laser spectroscopy of nv- and nv0 colour centres in synthetic diamond, Opt. Mater. Express 7, 2571 (2017).DOI
  40. [40]C. Santori, P. Tamarat, P. Neumann, J. Wrachtrup, D. Fattal, R. G. Beausoleil, J. Rabeau, P. Olivero, A. D. Greentree, S. Prawer, F. Jelezko, and P. Hemmer, Coherent population trapping of single spins in diamond under optical excitation, Phys. Rev. Lett. 97, 247401 (2006).DOI
  41. [41]N. Takei, M. Takeuchi, Y. Eto, A. Noguchi, P. Zhang, M. Ueda, and M. Kozuma, Faraday rotation with a single-nuclear-spin qubit in a high-finesse optical cavity, Phys. Rev. A 81, 042331 (2010).DOI
  42. [42]Y. Takahashi, K. Honda, N. Tanaka, K. Toyoda, K. Ishikawa, and T. Yabuzaki, Quantum nondemolition measurement of spin via the paramagnetic faraday rotation, Phys. Rev. A 60, 4974 (1999).
  43. [43]M. Atatüre, J. Dreiser, A. Badolato, and A. Imamoglu, Observation of faraday rotation from a single confined spin, Nature physics 3, 101 (2007).DOI
  44. [44]V. M. Acosta, E. Bauch, M. P. Ledbetter, A. Waxman, L.-S. Bouchard, and D. Budker, Temperature dependence of the nitrogen-vacancy magnetic resonance in diamond, Phys. Rev. Lett. 104, 070801 (2010).pubmed.ncbi.nlm.nih.gov/20366868
  45. [45]J. F. Barry, M. H. Steinecker, S. T. Alsid, J. Majumder, L. M. Pham, M. F. O’Keeffe, and D. A. Braje, Sensitive ac and dc magnetometry with nitrogen-vacancy-center ensembles in diamond, Phys. Rev. Appl. 22, 044069 (2024).arxiv.org/abs/2305.06269
  46. [46]H. Crepaz, L. Y. Ley, and R. Dumke, Cavity enhanced atomic magnetometry, Sci. Rep. 5, 15448 (2015).DOI
  47. [47]S. Li, P. Vachaspati, D. Sheng, N. Dural, and M. V. Romalis, Optical rotation in excess of 100 rad generated by rb vapor in a multipass cell, Phys. Rev. A 84, 061403 (2011).DOI
  48. [48]A. Pontin, H. Fu, M. Toros, T. S. Monteiro, and P. F. Barker, Simultaneous cavity cooling of all six degrees of freedom of a levitated nanoparticle, Nat. Phys. 19, 1003 (2023).DOI
  49. [49]U. Delić, M. Reisenbauer, K. Dare, D. Grass, V. Vuletić, N. Kiesel, and M. Aspelmeyer, Cooling of a levitated nanoparticle to the motional quantum ground state, Science 367, 892 (2020).
  50. [50]C. Wan, M. Scala, G. W. Morley, A. T. M. A. Rahman, H. Ulbricht, J. Bateman, P. F. Barker, S. Bose, and M. S. Kim, Free nano-object Ramsey interferometry for large quantum superpositions, Phys. Rev. Lett. 117, 143003 (2016).DOI

Paper details

vlnc:W_bpc2kvv8
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents