betaFeedback

WorksPhysics and Astronomy

Wave induced fracture of a sea ice analog

Abstract

We study at the laboratory scale the rupture of thin floating sheets made of a brittle material under a wave-induced mechanical forcing. We show that the rupture occurs where the curvature is maximum and the break-up threshold strongly depends on the wave properties. We observe that the critical stress for fracture depends on the forcing wavelength. Hence our observations are incompatible with a critical stress criterion for fracture. Instead, our measurements can be rationalized as an energy criterion: a fracture propagates when the material surface energy is lower than the released elastic energy, which depends on the forcing geometry. In light of these findings, it may be worthwhile to revisit current numerical models of sea ice fracture by ocean waves.

Introduction - The freezing of ocean water forms sea ice, that covers the Arctic region and surrounds Antarctica. When exposed to ocean waves, sea ice breaks [1, 2, 3] forming fragments of multiple sizes [4]. This phenomenon occurs in partially ice-covered region, called Marginal Ice Zone (MIZ) [5, 6]. The MIZ plays a crucial role in the climate dynamics [7] and marine biology [8] of these regions. Sea ice forms a thin brittle layer, and its fracture by waves is currently modelled by a critical strain [9].

In general, the fracture of a thin sheet of brittle material depends on the forcing geometry and the presence of existing cracks [10, 11]. The forcing geometry here results from the surface wave propagation under the ice. Therefore, the fracture threshold should result from an interplay between the mechanical properties of the sheet and the characteristics of the waves. In the absence of fracture, the deformation of a thin (kh≪1kh \ll1 with kk the wavenumber and hh the thickness), floating elastic sheet by surface waves has been previously studied, both in the linear [12] or weakly non-linear regime [13]. In the linear regime, neglecting the sheet inertia and surface tension, the deformation follows the dispersion relation of hydro-elastic waves [14],

ω2=gk+Dρk5,(1)\omega^2 = gk + \frac{D}{\rho}k^5, \tag*{(1)}

where ω\omega is the angular frequency, kk the wavenumber, gg the acceleration of gravity, ρ\rho the liquid density and DD the flexural modulus. The modulus DD is related to the mechanical properties of the sheet, D=Eh3/(12(1−ν2))D = Eh^3/(12(1-\nu^2)), with EE the Young’s modulus and ν\nu Poisson’s ratio. The elasto-gravity length ℓD=(D/ρg)1/4\ell_D = (D/\rho g)^{1/4} separates the gravity dominated regime (kℓD≪1k\ell_D \ll1) from the elastic regime kℓD≫1k\ell_D \gg1. For an ice fragment excited by free surface waves, the wavelength depends on the regime of wave propagation [15, 16], hence we expect the fracture threshold to depend on the ratio kℓDk\ell_D. Although the mechanical properties of sea ice are known to be highly variable, due to variations of composition, age or salt content [17, 18], the fracture criterion currently used in regional and global models is based on a critical strain [9, 19]. This criteria depends neither on the ice mechanical properties nor on the flexural length ℓD\ell_D.

Previous works focusing on the wave fracturing of either natural sea ice at the geophysical scale [20] or artificially grown ice at the laboratory scale [21] have suggested that sea ice breaks where the curvature is maximum. However, the forcing geometry in these studies has not been systematically varied. At the laboratory scale, L. Saddier et al. [22] recently studied the fracturing of a mimetic material. They use a granular raft formed by the capillary aggregation of micrometric particles [23] to investigate the fracture induced by waves. However, the raft broke under viscous stresses, a different fracture mechanism than bending induced fracture. In this letter, we study the fracture of a thin brittle sheet at the laboratory scale. The floating crust is made of a material brittle enough to break when bent by surface waves. Using stationary waves of varying wavelength, we discriminate between possible fracture criterion. We find that the critical stress depends on the forcing geometry, and we model the fracture threshold with an energetic criteria involving the sheet geometry. We eventually discuss the potential implication of our findings to the fracture of sea ice by ocean waves.

Experimental set-up - We form a thin brittle solid crust floating on the water surface, using a commercial glue varnish (Vernis-colle spray Megacrea DIY 28715). The varnish is sprayed from a height of about 15 cm on a water volume of 80 x 28 x 11 cm3^3. The varnish drops dry on the water surface, forming a floating, textured and semi-transparent solid crust. We combine pycnometer and weight measurements of the deposited mass to deduce the varnish thickness hh and density ρv\rho_v. We find average values of ρv=680±26\rho_v = 680 \pm26 kg.m−3^{-3} and hˉ=mv/(ρvSv)≃100μ\bar{h} = m_v/(\rho_v S_v) \simeq100\mum, where SvS_v is the covered area. For each varnish crust, we observe spatial variations of its transparency. Using the Beer-Lambert absorption law, we infer a spatial thickness variation of 14%. From one realisation to another, we also observe significant variations of the averaged thickness estimate, ranging from 57 to 207μ\mum. As the varnish crust is composed of micro-droplets that solidify into coagulating grains, it also presents heterogeneities at the droplet scale, that is, on the order of tens of microns.

Figure 1. a) Sketch of the experimental set-up, showing the varnish layer and the one dimensional profilometry system. b) Experimental measurements of the dispersion relation of surface waves propagating under a varnish layer of thickness h=158±22 μmh = 158 \pm22\ \mu\mathrm{m} (blue circles) obtained from a single experiment. The gravito-capillary dispersion relation (black dashed line)is superimposed. The experimental data points lie on the flexural branch, ω2∼k5\omega^2 \sim k^5.

To characterize the varnish mechanical properties, we use the experimental set up sketched in [Fig. 1a)]. Sinusoidal plane waves are generated with a linear motor (LinMot DM01-23x80F-HP-R-60 MS11), which actuates an inclined plate oriented with an angle −10∘-10^\circ with the vertical. We vary concomitantly the wave frequency ff from 1 to 100 Hz and the amplitude AA from 10 to 1 mm. For these small wave amplitudes, the varnish does not break, and waves propagate at the surface.

We use a one-dimensional profilometry system to extract the wave properties (ff, AA, wavenumber kk). A laser sheet is projected onto the varnish surface with an angle θ\theta ranging from 5 to 30∘30^\circ to adapt the magnification ratio, which varies between 1.7 and 11 depending on the required vertical resolution. Since the laser sheet is not significantly reflected by the water surface, all wave profiles are measured at the surface of the continuous varnish. We record top-view images of the varnish and the laser line with a Basler a2A1920-160ucBAS color camera of resolution 1920 x 1200 pixels, corresponding to a 48 x 30 cm field of view. The sampling frequency is chosen to capture a minimum of 5 images per wave period. Using image processing, we extract the position of the laser line with sub-pixel accuracy. We obtain the wavenumber kk and the amplitude AA of the surface wave from spatial Fourier analysis. [Fig. 1b)] shows the dispersion relation (blue diamond) of the surface waves, namely the angular frequency ω\omega as a function of the wavenumber kk for a varnish layer of thickness h=158±22 μmh = 158 \pm22\ \mu\mathrm{m}. The waves follow the dispersion relation (eq. 1). The flexural modulus DD depends on the Young’s modulus EE, the thickness hh, and the Poisson’s ratio ν\nu. Using DD as a fit parameter, we obtain a quantitative agreement with D=3.1±0.1×10−5 J m−2D = 3.1 \pm0.1 \times10^{-5}\ \mathrm{J\,m^{-2}}. We find that the varnish layer behaves as a solid. We associate a flexural length

ℓD=(Dρg)1/4=7.5±0.1 mm,(2)\ell_D = \left(\frac{D}{\rho g}\right)^{1/4} = 7.5 \pm0.1\ \mathrm{mm}, \tag*{(2)}

that separates the gravito-capillary wave regime (kℓD<1k\ell_D < 1) from the hydro-elastic (kℓD>1k\ell_D > 1) wave regime. Repeating the experiment for different varnish layers, we systematically extract the flexural modulus and the varnish thickness. We find an average varnish Young’s modulus E=65±14E = 65 \pm14 MPa using ν=0.4\nu= 0.4.

The corresponding flexural length being always larger than the capillary length (ℓc∼2.4\ell_c \sim2.4 mm), capillarity is negligible for all wavelengths.

Fracturing with waves - For larger wave amplitudes, the varnish layer fractures into multiple fragments. As an example, [Fig. 2a] shows 3 snapshots of a varnish layer seen from above, after respectively 12, 105 and 203 periods of oscillation, for f=3.33f = 3.33 Hz, A=6.7A = 6.7 mm, h≃150 μmh \simeq150\ \mu\mathrm{m} and a wavelength λ=14\lambda= 14 cm. We observe a complex dynamics of fragmentation: the orientation and the length of the first fractures present a wide distribution. On a longer time scale, the fragments collide and erode. This leads to the creation of very small fragments with a typical grain size of 100 μm\mu\mathrm{m}, while larger fragments become more circular. At last, fragmentation and erosion continue until the layer reduces to grain-sized fragments. To better control the geometry of the first fractures, we modify the setup to produce stationary, planar waves.

For each forcing frequency, we adapt the length of the water tank to a multiple of half the wavelength. Under a stationary wave pattern, the stress field is such that the nodes maximize tension, whereas the crest/trough (anti-nodes) maximizes bending and the viscous stress applied by the liquid on the sheet bottom. [Figure 2b)] presents a photograph of an experiment with 3 wavelengths after 307 forcing periods with λ=27\lambda= 27 cm, A=5.9A = 5.9 mm, f=2.397f = 2.397 Hz and h=90±13h = 90 \pm13 µm and shows that the waves are non-linear, since Ak=0.14Ak = 0.14.

Figure 2. a) 3 Photographies issued from the fracture of a single varnish sheet (h≃150 μmh \simeq150\ \mu\mathrm{m}) by propagative waves (f=3.33f = 3.33 Hz, A=6.7A = 6.7 mm and λ=14\lambda= 14 cm), after 12, 105 and 203 periods. b) Photography of a varnish sheet after 307 periods with λ=27\lambda= 27 cm, A=5.9A = 5.9 mm, f=2.397f = 2.397 Hz and h=90±13 μmh = 90 \pm13\ \mu\mathrm{m}. The varnish has broken on the anti-nodes of the waves. c) Schematical representation of the sheet geometry near a fracture tip. A planar, non-linear wave locally induces a curvature on a characteristic length LκL_{\kappa} in the transverse direction. For a large enough amplitude, a fracture of length LcrackL_{\mathrm{crack}} propagates along the wave crest/trough.

The laser line used for the profilometry appears in red. Superimposed in solid blue is the position of the anti-nodes. We observe that the varnish layer breaks along 4 lines parallel to the wave front separated by λ/2\lambda/2. Occasionally, secondary fractures appear in the direction perpendicular to the wave front. For each experiment we performed, the primary fractures appear at the anti-nodes, which correspond to maxima of curvature κ\kappa, i.e. loci of maximum flexural stress. The viscous stress is also maximum on the anti nodes. However, it decreases with the wavelength, and, as shown later in [Figure 3c)], our experimental results show that the fracture threshold in amplitude increases with the wavelength. Consequently, we rule out viscous stress as fracture mechanism. We thus conclude that the physical mechanism responsible for the first fracture of the varnish is bending rather than uniaxial tension or viscous stress.

Figure 3. a) Crack propagation in a varnish layer of thickness h=57±8h = 57 \pm8 µm for waves (λ=43.12\lambda= 43.12 cm) of increasing amplitude (images 1, 2 and 3), respectively A=0.96/1.18/1.34A = 0.96/1.18/1.34 cm. b) Crack length LcrackL_{\mathrm{crack}} as a function of the wave amplitude AA corresponding to the experiment of [Figure 3a)]. A linear fit of the experimental data (red line) gives the threshold amplitude for break-up Ac=1.01A_c = 1.01 cm corresponding to Lcrack=0L_{\mathrm{crack}} = 0. c) Wave amplitude threshold AcA_c as a function of the wavelength λ\lambda for different varnish layers, showing a linear relationship in a log-log scale. The varnish layer breaks in the non-linear wave regime of propagation, since Ack≃0.16A_ck \simeq0.16.

Fracture threshold - To study the fracture threshold, we excite stationary waves starting from a water surface at rest. Doing so, we observe a peculiar transient regime. The wave amplitude grows to a maximum over the first few periods, then decay to approximately 70% of the maximum to reach a stationary regime. As a consequence, crack evolution is observed only during the 2 or 3 periods over which the amplitude is near its maximum.

[Figure 2c)] presents a sketch of the fracture geometry in the vicinity of an existing crack. We assume that the waves are planar, with an amplitude AA, a frequency ff, and a wavelength λ\lambda. We define LκL_{\kappa}, the typical size on which the curvature is maximal, and LcrackL_{\mathrm{crack}}, the length of the first crack.

[Figure 3a)] shows an experiment with f=1.832f = 1.832 Hz, λ=43.12\lambda= 43.12 cm and h=57±8h = 57 \pm8 µm for three increasing forcing amplitudes AA. We observe that the varnish layer breaks above a critical threshold AcA_c, on a finite crack length LcrackL_{\mathrm{crack}} (images 1 to 3), which increases rapidly with increasing forcing amplitude. To extract the threshold amplitude AcA_c of crack apparition, we plot the crack length LcrackL_{\mathrm{crack}} as a function of AA on [Figure 3b)]. We observe that Lcrack(A)L_{\mathrm{crack}}(A) is an affine function of AA for A>AcA > A_c.

We then vary the wave frequency and we measure the critical wave amplitude AcA_c for a wavelength λ\lambda ranging from 5 to 50 cm. Each fracture experiments is performed in the gravity regime since kℓD<1k\ell_D < 1. [Figure 3c)] shows that the threshold amplitude is proportional to the wavelength and corresponds to a constant steepness

of Ack=0.16A_ck = 0.16.

However, the relevant quantity for fracture propagation induced by a bending load is the curvature κ\kappa of the plate. For Ack∼0.16A_ck \sim0.16, the wave profile is expected to be non linear, and we therefore investigate further the wave geometry near the maximum of curvature. [Figure 4a)] presents the zoomed in wave profiles near the maximum of curvature, at the critical amplitude, for various wavelength. The normalized relative elevation η=ηmin⁡/(Amax⁡−ηmin⁡)\eta= \eta_{\min}/(A_{\max} - \eta_{\min}) is plotted as a function of the position xx in unit of λ\lambda. The colormap represents the wavelength, from 6.2 cm in dark blue to 54.1 cm in light cyan. We observe that the wave profiles near their maximum are indeed non linear. The length LκL_{\kappa} is defined as the half width at maximum curvature, and its average is represented with a blue circle. We observe that LκL_{\kappa} is constant in unit of λ\lambda, showing graphically that LκL_{\kappa} is proportional to the wavelength.

Figure 4. a) Wave profiles near the maximum of curvature for different wavelength. The normalized relative elevation η−ηmin⁡/(Amax⁡−ηmin⁡)\eta-\eta_{\min}/(A_{\max}-\eta_{\min}) is plotted as a function of the position xx in unit of λ\lambda. The wavelength varies from 6.2 to 54.1cm. The average LκL_{\kappa}, the half width at maximum curvature, is showed with a blue circle, highlighting the auto-similarity of the wave profiles as well as their non linearity. b) Half width of max curvature LκL_{\kappa} as a function of the wavelength λ\lambda for the closest wave profile to the threshold. It shows a linear relationship Lκ=αλL_{\kappa}=\alpha\lambda, with α=0.079±0.004\alpha=0.079\pm0.004. c) Curvature threshold κc\kappa_c for fracture as a function of the wavelength λ\lambda, compatible with κc=βλ−1/2\kappa_c=\beta\lambda^{-1/2} with β=5.82±0.6 m−1/2\beta=5.82\pm0.6\ {\rm m}^{-1/2}.

[Figure 4b)] shows LκL_{\kappa} at threshold as a function of λ\lambda. The black dash line corresponds to a linear fit Lκ=αλL_{\kappa} = \alpha\lambda with α=0.079±0.004\alpha= 0.079 \pm0.004. In comparison, we expect α=1/3\alpha= 1/3 for linear waves. We also measure the magnitude of the curvature peak κ\kappa, by fitting a second order polynomial on a length LκL_{\kappa} around the maximum of amplitude. We assume that for weak nonlinear wave profiles, the curvature can be expressed as κ=aA+bA2\kappa= aA + bA^2, with two unknown coefficients aa and bb. We fit these coefficients to compute the curvature threshold κc\kappa_c corresponding to the amplitude threshold AcA_c for each wavelength.

[Fig. 4c)] shows the critical curvature κc\kappa_c as a function of the wavelength λ\lambda. We observe that the curvature threshold decreases significantly with the wavelength. Our observations on the break-up of the varnish layer by waves are therefore incompatible with a fracture criterion based on a critical stress σc=Eκch\sigma_c=E\kappa_ch, independent of the wavelength.

Fracture models - We propose an energy based criterion to model the crack propagation induced by the waves. Starting from an existing crack, such an energy criterion for fracture propagation results from the balance between the increment of surface energy GG required to form a new surface and the strain energy dUTdU_T released when a crack propagates on a surface dSdS. GG is also called energy release rate and is written [24, 25]:

G=−dUTdS,(3)G=-\frac{dU_T}{dS}, \tag*{(3)}

with dS=2hδLcrackdS=2h\delta L_{\mathrm{crack}} the crack surface. The elastic energy released by the crack propagation can be written as [26]:

UT=D∬Σκ2(x,y) dx dy.(4)U_T=D\iint_{\Sigma}\kappa^2(x,y)\,dx\,dy. \tag*{(4)}

Where κ\kappa is the curvature field on the sheet. For an imposed curvature, the elastic energy must be computed on the entire sheet. In our situation, due to the imposed displacement by non linear water waves, the plate is only curved on a characteristic length LκL_{\kappa}. Once a crack of length Lcrack>LκL_{\mathrm{crack}}>L_{\kappa} is present, we assume that the elastic energy UTU_T can only be released on the characteristic length LκL_{\kappa} in the direction perpendicular to the crack, as sketched on [Fig. 2c)]. The elastic energy is released on a surface Σ∼LκδLcrack\Sigma\sim L_{\kappa}\delta L_{\mathrm{crack}}, and we estimate the increment of UTU_T around the crack as:

dUT∼−Dκ2LκδLcrack.(5)dU_T\sim-D\kappa^2L_{\kappa}\delta L_{\mathrm{crack}}. \tag*{(5)}

The fracture threshold is reached when the energy release rate GG becomes equal to the surface energy GcG_c [24, 25, 27]. We then define the break-up criterion as:

G=Gc∼Dκc2Lκ2h(6)G=G_c\sim D\kappa_c^2\frac{L_{\kappa}}{2h} \tag*{(6)}

We deduce that at the break-up threshold:

κc=2GchDLκ−1/2=βλ−1/2,(7)\kappa_c=\sqrt{\frac{2G_ch}{D}}L_{\kappa}^{-1/2}=\beta\lambda^{-1/2}, \tag*{(7)}

where GcG_c is the surface energy of the material, which is independent of the wave properties. We observe that GG is independent of LcrackL_{\mathrm{crack}}, meaning that the crack propagation is marginally stable. From the result of [Fig. 4c)], we deduce that the critical curvature for breakup κc\kappa_c scales as κc=βλ−1/2\kappa_c=\beta\lambda^{-1/2} with β=2σGchD=5.82±0.6 m−1/2\beta=\sqrt{\frac{2\sigma G_ch}{D}}=5.82\pm0.6\ {\rm m}^{-1/2} (eq. 7) (0.6 m−1/2^{-1/2} being the standard deviation error from the fit). The uncertainty on the constant β\beta can be attributed to the variations of the material defects from one run to another, due to the varnish heterogeneity. The variations of β\beta with the varnish thickness is not significant enough to be conclusive.

Discussion - In this study, we manage to form a thin crust of a brittle material floating on a water surface, and we measure its elastic properties using a non invasive technique. When excited by gravity waves, the crust breaks from bending and we show that the breakup threshold depends on the forcing geometry. The corresponding critical stress for fracture propagation also depends on the forcing wavelength. Our observations are incompatible with a critical strain criterion for fracture.

A geometry dependent fracture threshold has been observed recently in a different configuration by Prabowo et al. [28], in which they highlighted the role of the size of a spherical indenter on the fracture threshold. Our fracture threshold can be rationalized using an energy criterion, which depends on the critical curvature κc\kappa_c, and the characteristic length on which the elastic energy can be released, LκL_\kappa. The threshold is controlled by a crack propagation criterion rather than a crack initiation criterion, as a consequence of the varnish heterogeneities from the grain scale to the sheet scale. The magnitude and the scale of these heterogeneities are most likely a significant source of errors and could explained the scatter of the critical curvature. However, since these variations are uncorrelated with the forcing scale λ\lambda, our main result, a fracture criteria that depends on the wavelength, still holds.

The break-up of sea ice by waves is also triggered by flexural stresses [29]. Extrapolating our criterion to sea ice, the critical stress may depend on the forcing geometry, hence increasing with the wavenumber kk, compatible with field observations [30]. However, our experiments are conducted with non-linear and mainly monochromatic waves which is rarely the case in MIZ. For linear waves, we expect the same break-up criterion to hold with α=1/3\alpha= 1/3. For a broader wave spectrum, to the best of our knowledge, there is no test of an energy criterion against field data.

Currently, the field observations remain too scarce to isolate the effects of the local geometry on the fracture threshold and cannot fully discriminate between breakup criteria. We expect that further experiments on ice at various scales could help to better understand the fracture of sea ice by ocean swell.

We thank Anaïs Abramian, Michael Berhanu, Véronique Dansereau, Sébastien Kuchly, Gabriel Le Doudic, Nicolas Mokus, Sylvain Patinet, Benoit Roman and Vasco Zanchi for fruitful discussions. We thank Amaury Fourgeaud and Laurent Quartier for technical assistance. This work has benefited from the financial support of Mairie de Paris through Emergence(s) grant 2021-DAE-100 245973, and from the Agence Nationale de la Recherche through grant MSIM ANR-23-CE01-0020-02.

References

  1. [1]P. Lu, Z. Li, Z. Zhang, and X. Dong, Journal of Geophysical Research 113 (2008).
  2. [2]M. G. Asplin, R. Galley, D. G. Barber, and S. Prinsenberg, Journal of Geophysical Research: Oceans 117 (2012).
  3. [3]A. K. Liu and E. L. Mollo-Christensen, Journal of Physical Oceanography 18, 1702 (1988).
  4. [4]T. Toyota, S. Takatsuji, and M. Nakayama, Geophysical Research Letters 33 (2006).
  5. [5]V. A. Squire, Annual Review of Fluid Mechanics 52 (2019).
  6. [6]D. Dumont, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences 380, 20210253 (2022).
  7. [7]C. Eayrs, D. Holland, D. Francis, T. Wagner, R. Kumar, and X. Li, Reviews of Geophysics 57, 1037 (2019).
  8. [8]M. Arndyna, M. Babin, M. Gosselin, E. Devred, L. Rainville, and J.-É. Tremblay, Geophysical Research Letters 41, 6207 (2014).
  9. [9]J. J. Voermans, J. Rabault, K. Filchuk, I. Ryzhov, P. Heil, A. Marchenko, C. O. Collins III, M. Dabboor, G. Sutherland, and A. V. Babanin, The Cryosphere 14, 4265 (2020).
  10. [10]T. Digrantara and M. Aliabadi, Engineering Fracture Mechanics 69, 1465 (2002).
  11. [11]N. Hasebe and S. Inohara, Ingenieur-Archiv 49, 51 (1980).
  12. [12]L. Domino, M. Fermigier, E. Fort, and A. Eddi, EPL (Europhysics Letters) 121, 14001 (2018).
  13. [13]L. Deike, M. Berhanu, and E. Falcon, Phys. Rev. Fluids 2, 064803 (2017).
  14. [14]H. Lamb, Proceedings of the Royal Society of London. Series A, Containing papers of a mathematical and physical character 93, 114 (1917).
  15. [15]F. Montiel, F. Bonnefoy, P. Ferrant, L. G. Bennetts, V. A. Squire, and P. Marsault, Journal of Fluid Mechanics 723, 604–628 (2013).
  16. [16]F. Montiel, L. G. Bennetts, V. A. Squire, F. Bonnefoy, and P. Ferrant, Journal of Fluid Mechanics 723, 629–652 (2013).
  17. [17]J. J. Petrovic, Journal of Materials Science 38, 1 (2003).
  18. [18]G. Timco and W. Weeks, Cold regions science and technology 60, 107 (2010).
  19. [19]J. Li, A. V. Babanin, Q. Liu, J. J. Voermans, P. Heil, and Y. Tang, Journal of Marine Science and Engineering 9 (2021), 10.3390/jmse9040365.
  20. [20]E. Dumas-Lefebvre and D. Dumont, The Cryosphere 17, 827 (2023).
  21. [21]A. Herman, K.-U. Evers, and N. Reimer, The Cryosphere 12, 685 (2018).
  22. [22]L. Saddier, A. Palotai, M. Aksil, M. Tsamados, and M. Berhanu, Physical Review Fluids, 094302 (2024).
  23. [23]C. Planchette, E. Lorenceau, and A.-L. Biance, Soft Matter 8, 2444 (2012).
  24. [24]H. Tada, P. Paris, and G. Irwin, The Stress Analysis of Cracks Handbook (ASME Press, 2000).DOI
  25. [25]T. Anderson and T. Anderson, Fracture Mechanics: Fundamentals and Applications, Third Edition (Taylor & Francis, 2005).DOI
  26. [26]S. Timoshenko and S. Woinowsky-Krieger, Theory of Plates and Shells, Engineering mechanics series (McGraw-Hill, 1959).
  27. [27]Zehnder, A. (2012). Fracture Mechanics. In Lecture Notes in Applied and Computational Mechanics.
  28. [28]A. R. Prabowo, R. Ridwan, T. Tuswan, D. F. Smaradhana, B. Cao, and S. J. Baek, Applications in Engineering Science 18, 100177 (2024).
  29. [29]V. A. Squire, J. P. Dugan, P. J. Wadhams, P. J. Rottier, and A. K. Liu, Annual Review of Fluid Mechanics 27, 115 (1995).
  30. [30]A. L. Kohout, M. J. M. Williams, T. Toyota, J. Lieser, and J. Hutchings, Deep Sea Research Part II: Topical Studies in Oceanography 131, 22 (2016).

Paper details

vlnc:W_br36gmed
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents