betaFeedback

WorksPhysics and Astronomy

Revealing Modeshape Complexity and Sensitivity in Torsional Vibrations of Microcantilevers with Overhang- and T-shaped Geometries

Abstract

The torsional vibration of atomic force microscope (AFM) cantilevers is critical for high-sensitivity measurements, yet existing models for width-varying cantilevers often rely on approximations that lead to significant discrepancies with experimental data. Unlike prior studies, this work introduces a refined analytical framework to precisely compute resonance frequencies and mode shapes, including higher-order modes, for overhang- and T-shaped microcantilevers, validated through targeted experimental comparisons. By systematically analyzing the effects of overhang length, we reveal previously unreported multi-maxima mode shapes and demonstrate how geometric tuning can controllably shift resonant frequencies. Furthermore, we establish a quantitative relationship between modal sensitivity and cantilever-surface coupling strength, providing actionable design principles for optimizing AFM cantilever performance. Our results not only reconcile theoretical predictions with experimental observations but also offer practical guidelines for tailoring cantilever geometry to achieve specific frequency responses in applications such as nanomechanical imaging and surface property mapping. This work advances the design of next-generation AFM probes by bridging the gap between analytical models and real-world operational demands.

Introduction

Atomic force microscopy (AFM) has emerged as a powerful tool for high-resolution surface characterization and single-molecule force spectroscopy, offering exceptional sensitivity and versatility across diverse environments (e.g., air, liquid, and vacuum)[1, 2, 3]. By monitoring cantilever deflections or shifts in resonant frequency, AFM enables the quantification of structural, thermal, and mechanical properties at the nanoscale[4, 5]. Recent advances in cantilever dynamics have further expanded its applications, from biomolecular interaction mapping to nanomechanical property imaging[6].

While flexural vibration modes dominate conventional AFM operation, torsional modes have gained prominence for their unique advantages in specialized scenarios. For instance, torsional vibrations exhibit superior sensitivity for stiff materials and lateral stiffness measurements[7, 8], enabling novel techniques such as sidewall probe imaging[9]. Sharos et al. demonstrated that torsional modes achieve higher mass sensitivity than bending modes[10], while Turner et al. highlighted their efficacy in higher-order mode applications[7]. Despite these benefits, existing models for torsional dynamics in width-varying cantilevers (e.g., overhang or T-shaped geometries) remain limited by approximations, leading to discrepancies between theory and experiments. This gap is particularly critical for next-generation AFM probes, where geometric tuning could unlock tailored frequency responses and enhanced sensitivity.

Beyond simple rectangular beams, complex geometries such as inverted T-shaped or V-shaped cantilevers[11, 12] have attracted significant interest due to their enhanced performance. However, accurately determining their resonant frequencies and mode shapes remains challenging due to non-uniform width and thickness distributions. Zhang et al.[13] investigated variable-width cantilevers using polynomial approximations to circumvent analytical difficulties in solving the Euler-Bernoulli equation. While their approach revealed a geometric dependence of resonant frequencies, the solutions were computationally cumbersome and sensitive to polynomial assumptions. Plaza et al.[11] demonstrated that microcantilever arrays could mitigate initial deflections, yet precise frequency determination still relied heavily on experimental calibration. These limitations underscore the need for a robust analytical framework to predict the vibrational characteristics of non-uniform cantilevers—a gap this work addresses.

The overhang region, in particular, plays a critical role in cantilever dynamics, influencing both individual performance and coupled-array behavior. Recent studies show that the coupling strength between cantilevers in an array depends linearly on overhang length and inversely on the cubic power of overhang width[14]. This geometric sensitivity highlights the importance of accurate modeling, especially for applications requiring high-resolution surface topography or synchronized array measurements[15, 16, 17].

Our work bridges the gap between theory and experiment by providing precise analytical solutions for overhang-type cantilevers, reducing discrepancies in frequency predictions. Modifications to beam geometry, such as overhang length and width, can dramatically alter dynamic behavior, including the emergence of higher harmonic modes[5]. While prior studies have explored various geometries—such as Payam et al. examining flexural spring constants in fluids[18, 19] and Plaza et al. optimizing T-shaped structures[11]—none have systematically resolved the torsional vibration challenges unique to overhang designs. This study fills that void, offering a unified approach to optimize cantilever performance for both single-probe and array-based applications.

Prior models fail to reconcile analytical predictions with experimental frequency ratios, as shown by Sadewasser et al.[20]. Our work resolves this by presenting a comprehensive analytical and numerical investigation of how geometric modifications in overhang- and T-shaped cantilevers alter their torsional mode shapes, resonant frequencies, and—critically—their measurement sensitivity. Unlike prior studies focusing solely on frequency tuning, we systematically quantify the influence of overhang and T-section dimensions on both dynamic response and modal sensitivity, bridging a key gap in AFM cantilever design. Our analytical model predicts torsional-to-flexural frequency ratios within 3–5% of Sadewasser et al.’s experimental data (solid blue circles), achieving an R2R^2 correlation coefficient of 0.98.

In Section II, we derive exact frequency equations for T-shaped cantilevers (excluding external interactions) and establish how variations in overhang length, width, and T-junction geometry reshape mode shapes and harmonic spectra.

§ 0.3 presents validated results, highlighting two key advances: (i) Geometric control of higher-order modes: We demonstrate how overhang tuning can selectively enhance or suppress specific harmonics, enabling tailored frequency responses. (ii) Sensitivity-stiffness coupling: In § 0.3 C, we introduce a generalized model for modal sensitivity incorporating sample interactions via the effective rigidity parameter, resolving prior discrepancies between theoretical and experimental sensitivity trends.

Our findings provide actionable guidelines for designing next-generation AFM probes, particularly for applications requiring high lateral resolution (e.g., nanoscale friction mapping) or synchronized array measurements. The conclusions in § 0.4 summarize these insights and outline pathways for future experimental validation.

Material and Methods

The cantilever is assumed to be fabricated from silicon nitride[21], consistent with conventional AFM experiments, with a length L=200L = 200–500500 μ\mum, width a=35a = 35 μ\mum, and thickness t=1.5t = 1.5 μ\mum. Building on the analytical framework developed for flexural vibrations in nonuniform cantilevers[14, 22], we extend this approach to model torsional vibrations in overhang- and T-shaped structures [see Figure 1]. Our analysis systematically investigates how variations in the overhang and T-section dimensions influence the resonant frequencies and mode shapes of the cantilevers. Therefore, a detailed analysis on the multi-mode behavior of the cantilever is required. We found that, (i) higher-order torsional modes play a significant role in the vibration dynamics, necessitating a detailed analysis of their contributions, and (ii) the dimensions of the overhang and T-parts critically affect both the frequency spectrum and mode shape distribution, highlighting the importance of precise geometric control for optimal performance.

A cantilever beam structure including an overhanging part and an inset showing the effective interaction stiffness

Figure 1. A cantilever beam structure including an overhanging part of length l0l_0 and width a0a_0 is clamped at x=0x=0 to the base (black region). For a0<aa_0<a, we have a T-shaped cantilever. The torsional modes are examined in the interaction with a sample via the effective interaction stiffness κl\kappa_l (inset).

The dynamic equation for the torsional vibration mode is written based on the Euler-Bernoulli theory of the beam[23, 24] as follows:

∂∂x[GJ(x)∂ϕ(x,t)∂x]−ρIp(x)∂2ϕ(x,t)∂t2=0,(1)\frac{\partial}{\partial x}\left[GJ(x)\frac{\partial\phi(x,t)}{\partial x}\right]-\rho I_p(x)\frac{\partial^2\phi(x,t)}{\partial t^2}=0, \tag*{(1)}

where ϕ(x,t)\phi(x,t) is the deflection angle at position xx and time tt. GG is the shear modulus and ρ\rho is the density of the beam. J(x)J(x) and Ip(x)I_p(x) are geometric functions of the beam cross section and the polar moment of inertia, respectively. Here, the cross section of the beam is a rectangular shape, hence, J(x)=a(x)t3/3J(x)=a(x)t^3/3 and Ip(x)=a3(x)t/12I_p(x)=a^3(x)t/12. It is shown that the width of the beam is xx-dependent. Hence, the general solution of Eq. (1) is ϕ(x,t)=ϕ(x)eiωt\phi(x,t)=\phi(x)e^{i\omega t}. Substituting the general solution into Eq. (1), one obtains the equations for the mode shape (xx-dependent) and the natural frequency. The mode shape equation reads,

ddx[GJ(x)dϕ(x)dx]+ρIp(x)ω2ϕ(x)=0.(2)\frac{d}{dx}\left[GJ(x)\frac{d\phi(x)}{dx}\right]+\rho I_p(x)\omega^2\phi(x)=0. \tag*{(2)}

For the current cross-section of the beam, the thickness of the overhang part and the outer cantilever part are assumed to be the same while the width is step-like with xx, a(x)=a0a(x)=a_0 if x≤l0x\le l_0 and a(x)=aa(x)=a if x>l0x>l_0. Equation (2) is divided into two equations. The first equation describes the overhang part, ϕ0′′(x)+γ02ϕ0(x)=0\phi_0''(x)+\gamma_0^2\phi_0(x)=0, and the second equation is for the cantilever part, ϕc′′(x)+γc2ϕc(x)=0\phi_c''(x)+\gamma_c^2\phi_c(x)=0. Here, γ0,c=ωρIp,0,cGJ0,c\gamma_{0,c}=\omega\sqrt{\frac{\rho I_{p,0,c}}{GJ_{0,c}}} is the characteristic frequency. Now, the frequency ratio is γcγ0=aa0=1κ\frac{\gamma_c}{\gamma_0}=\frac{a}{a_0}=\frac{1}{\kappa}, or, γ=γc=1κγ0\gamma=\gamma_c=\frac{1}{\kappa}\gamma_0 could be used for brevity. The solutions of the differential equations are,

ϕ0(x)=Asin⁡(κγx)+Bcos⁡(κγx),(3)\phi_0(x)=A\sin(\kappa\gamma x)+B\cos(\kappa\gamma x), \tag*{(3)}
ϕc(x)=Csin⁡(γx)+Dcos⁡(γx).(4)\phi_c(x)=C\sin(\gamma x)+D\cos(\gamma x). \tag*{(4)}

Solving the equation with suitable boundary conditions, we obtain a frequency equation,

κ2cos⁡(γ−γη)cos⁡(γηκ)−sin⁡(γ−γη)sin⁡(γηκ)=0,(5)\kappa^2\cos(\gamma-\gamma\eta)\cos(\gamma\eta\kappa)-\sin(\gamma-\gamma\eta)\sin(\gamma\eta\kappa)=0, \tag*{(5)}

where η=l0/L\eta=l_0/L; then the frequency is,

ω=γLGJcρIp,c.(6)\omega=\frac{\gamma}{L}\sqrt{\frac{GJ_c}{\rho I_{p,c}}}. \tag*{(6)}

And the mode shape is presented as,

ϕ0(x)=Asin⁡(κγx),(7)\phi_0(x) = A \sin(\kappa\gamma x), \tag*{(7)}
ϕc(x)=Acos⁡[(1−x)γ]sec⁡[(1−η)γ]sin⁡(κηγ)(8)\phi_c(x) = A \cos\left[(1-x)\gamma\right]\sec\left[(1-\eta)\gamma\right]\sin(\kappa\eta\gamma) \tag*{(8)}

The updated mode shapes, in the case of flexural vibration, have been shown to significantly modify that of the uniform cross-section cantilevers[22]. For the torsional modes, similar behavior is expected.

Results

Typical microcantilever dimensions span the following ranges: length (LL) = 50–500 μm\mu\mathrm{m}, width (aa) = 10–50 μm\mu\mathrm{m}, and thickness (tt) = 0.5–5 μm\mu\mathrm{m}. These ranges are consistent with experimental studies, such as those by[25] (silicon cantilevers: LL = 100–500 μm\mu\mathrm{m}, aa = 20–50 μm\mu\mathrm{m}, tt = 0.3–2 μm\mu\mathrm{m} and[26] (L≃500 μmL \simeq500\ \mu\mathrm{m}, aa = 97.2 μm\mu\mathrm{m}, tt = 0.8 μm\mu\mathrm{m}). In this work, we analyze silicon nitride microcantilevers (material properties in Table I), focusing on how their mode shapes and resonant frequencies evolve with geometric modifications.

ParametersSymbol (Unit)Value
LengthLL (μm\mu\mathrm{m})350
Widthaa (μm\mu\mathrm{m})35
Thicknesstt (μm\mu\mathrm{m})1.5
Young’s modulusEE (GPa)169
Densityρ\rho (kg/m3\mathrm{m}^{3})2300

Table I. Parameters of cantilever part.

By solving Eq. (5), the resonant frequencies and corresponding mode shapes can be determined. Figure 2 illustrates how variations in the geometric parameters κ\kappa and η\eta affect the oscillatory behavior of the solution along the horizontal axis. These oscillations correspond to the characteristic frequency solutions γ\gamma associated with the vibration modes.

Figure 2. Equation 5 is illustrated for several geometric configurations characterized by the parameters κ\kappa and η\eta. The red solid line represents a rectangular cantilever with κ=1\kappa= 1 and η=0\eta= 0, the blue dashed line corresponds to an overhang structure with κ=2\kappa= 2 and η=0.2\eta= 0.2, and the green dash-dotted line denotes a T-shaped cantilever with κ=0.5\kappa= 0.5 and η=0.8\eta= 0.8.

For the rectangular cantilever (represented by the solid red line), the first three modes occur at γ=π/2\gamma= \pi/2, 3π/23\pi/2, and 5π/25\pi/2, respectively. However, when the geometry is modified, these characteristic frequencies shift. For example, in the case of the overhang-shaped cantilever with κ=2\kappa= 2 and η=0.2\eta= 0.2 (blue dashed line), the first mode appears at γ≈1.712\gamma\approx1.712, the second at approximately 5π/45\pi/4, and the third at γ≈6.142\gamma\approx6.142. In contrast, for the T-shaped cantilever with κ=0.5\kappa= 0.5 and η=0.8\eta= 0.8 (green dash-dotted line), the first and second mode frequencies occur at γ≈1.608\gamma\approx1.608 and γ≈7.854\gamma\approx7.854, respectively.

Changes in mode shapes

The mode shapes have been expressed in Figure 3 for (a) the first mode and (b) the second mode. Figure 3(a) and 3(b) are presented for η=l0/L=0.5\eta= l_0/L = 0.5 and various values of overhang widths, κ=a0/a=1.0\kappa= a_0/a = 1.0 by black-solid, 0.5 by red-dotted, 0.8 by blue dashed, 1.5 by green dash-dotted, and 3.0 by pink dash-dot-dotted lines. The deflection angle at LL, x(L)/x(l0)x(L)/x(l_0), has been shown to increase as the width of the cantilever increases.

Figure 3. Mode shapes of cantilever beam for the two first modes with increasing the cantilever width via κ\kappa. Here, η=0.5\eta= 0.5. An increasing of κ\kappa implies a wider cantilever.

For the second mode, the mode shapes of κ=0.5\kappa= 0.5–0.8 deviate from that of κ=1\kappa= 1 for 0<x<L0 < x < L with a maximum that then decreases and approaches the value -1 for x=Lx = L, while those of κ>1\kappa> 1 greatly decrease (green dash-dotted lines and pink dash-dotted lines).

Figure 4 summarizes the behavior of the first four torsional modes, illustrating how the overhang affects the deflection angle at the beam’s free end. The color intensity represents the deflection magnitude, revealing distinct maxima patterns for each mode:

Figure 4. The deflection angle at LL, x(L)/x(l0)x(L)/x(l_0), for the first four modes with several maxima. The number of maxima is proportional to the mode number and exists for κ>1\kappa> 1.

  • Mode 1: Single maximum (not explicitly located but observable in color gradient).

  • Mode 2: Two maxima at l0/L≃0.05l_0/L \simeq0.05 and 0.40.4 (red regions).

  • Mode 3: Three maxima at l0/L≃0.025l_0/L \simeq0.025, 0.20.2, and 0.60.6.

  • Mode 4: Four maxima at l0/L≃0.01l_0/L \simeq0.01, 0.150.15, 0.30.3, and 0.650.65.

The number of maxima consistently equals the mode number, demonstrating a clear correlation between modal order and spatial oscillation patterns. This systematic behavior confirms the predictable influence of the overhang geometry on torsional vibration characteristics.

Changes in frequency

Examining the change in the cantilever frequency f=ω/2πf = \omega/2\pi, we observed an interesting nonmonotonic behavior in the dependence of ff on the overhang length η\eta. The frequency of the first mode initially increases Figure 5(a), reaching a maximum at η≃0.2\eta\simeq0.2, and then decreases rapidly as η\eta continues to increase. In the region near the maximum (from orange to red), the frequency increases with κ\kappa, i.e., with a larger overhang, which implies a stiffer cantilever.

Figure 5. The frequencies of the first four modes. (a) The first mode of the overhang-shaped (κ>1\kappa> 1) presents a maximal frequency at 0≤η≤0.250 \le\eta\le0.25 while the T-shaped (κ<1\kappa< 1) cantilevers have minima. (b)–(d) Higher modes have a tendency to reduce the frequency with η\eta and some small extrema appear.

The 2nd to 4th modes, on the other hand, no longer clearly exhibit a maximum. All frequencies tend to decrease rapidly as η\eta increases. For example, within the range η=0\eta= 0– 0.5, the second mode f2f_2 [Fig. 5(b)] decreases significantly from 1.0 to ≃0.5\simeq0.5 (1000 to 500 kHz). The 3rd and 4th modes [Fig. 5(c) and (d)] display a small peak before dropping to lower frequencies.

These findings are notable for several reasons. First, there is a nearly flat plateau in the frequency response followed by a rapid decline. This feature could be advantageous for controlling and tuning cantilever frequencies by adjusting the length of the overhang section, thereby enhancing high-harmonic frequencies[5, 27]. Second, effective modulation of higher-order modes, governed by the structure’s geometry, may enable the use of multiple modes in measurements, improve inter-mode coupling, and even support the appearance of high harmonics (since higher-order mode frequencies can be integer multiples of lower ones). Consequently, appropriate tuning of the overhang parameters can facilitate control over higher modes.

Our approach also shows strong agreement with previous research on cantilever frequencies. For instance, Sadewasser et al. investigated the dynamics of cantilevers with an overhanging section[20]. Compared to Sadewasser’s results, our method exhibits excellent consistency in the ratio between torsional (fT=ωT/2πf_T = \omega_T/2\pi) and flexural (fF=ωF/2πf_F = \omega_F/2\pi) frequencies under identical geometric conditions, as illustrated in Figure 6.

Figure 6. Ratio of torsional to flexural frequencies of overhang-shaped cantilever from the experiment of Sadewasser et al. (solid blue circles)[20] and this study (solid black line).

Torsional sensitivity

The sensitivity of the flexural modes in overhung and T-shaped cantilevers has recently been studied[19], demonstrating that the dimensions of the overhang section can significantly influence the cantilever’s frequency. For torsional modes, several investigations have been carried out by Abbasi et al.[28], focusing on cantilevers with sidewall probes in rectangular geometries. However, the torsional vibrations of overhung or T-shaped cantilevers have not yet been explored.

In this work, we analyze the torsional modal sensitivity of an overhung cantilever, assuming a tip-sample interaction modeled as a linear lateral spring with stiffness κl\kappa_l. This interaction is applied at the cantilever’s end position, x=Lx = L. The boundary condition at x=Lx = L is expressed as ϕ′(L)=−(κld2/(GJ))ϕ(L)=−βlϕ(L)\phi'(L) = -(\kappa_l d^2/(GJ))\phi(L) = -\beta_l\phi(L), where βl=(κld2/(GJ))\beta_l = (\kappa_l d^2/(GJ)). This results in an additional term in the matrix KK in Eq. (??). The modified matrix KK is written as follows [Eq. (9)],

Kl=[010000γcos⁡γ+βlsin⁡γ−γsin⁡γ+βlcos⁡γsin⁡κηγcos⁡κηγ−sin⁡ηγ−cos⁡ηγκ2cos⁡κηγ−κ2sin⁡κηγ−cos⁡ηγsin⁡ηγ].(9)K_l = \begin{bmatrix} 0 & 1 & 0 & 0 \\ 0 & 0 & \gamma\cos\gamma+\beta_l\sin\gamma& -\gamma\sin\gamma+\beta_l\cos\gamma\\ \sin\kappa\eta\gamma& \cos\kappa\eta\gamma& -\sin\eta\gamma& -\cos\eta\gamma\\ \kappa^2\cos\kappa\eta\gamma& -\kappa^2\sin\kappa\eta\gamma& -\cos\eta\gamma& \sin\eta\gamma \end{bmatrix}. \tag*{(9)}

Similarly, using the updated matrix KlK_l, a characteristic equation was obtained by calculating the determinant CC of the matrix. Finally, a characteristic equation for the frequency is obtained,

C=C0(κ,η,γ)+Cint(κ,η,βl,γ),(10)C = C_0(\kappa,\eta,\gamma) + C_{\mathrm{int}}(\kappa,\eta,\beta_l,\gamma), \tag*{(10)}

where

C0=γ{κ2cos⁡[γ(1−η)]cos⁡(γηκ)−sin⁡[γ(1−η)]sin⁡(γηκ)},(11)C_0 = \gamma\{\kappa^2\cos[\gamma(1-\eta)]\cos(\gamma\eta\kappa)-\sin[\gamma(1-\eta)]\sin(\gamma\eta\kappa)\}, \tag*{(11)}
Cint=βl{κ2sin⁡[γ(1−η)]cos⁡(γηκ)+cos⁡(γ(1−η)sin⁡(γηκ)}.(12)C_{\mathrm{int}} = \beta_l\{\kappa^2\sin[\gamma(1-\eta)]\cos(\gamma\eta\kappa)+\cos(\gamma(1-\eta)\sin(\gamma\eta\kappa)\}. \tag*{(12)}

C0C_0 and CintC_{\mathrm{int}} represent the non-contact and contact contributions, respectively. The variation of frequency with respect to η\eta and the coupling stiffness β\beta is shown in Figure 7 for the first and second modes. It is observed that, for κ<1\kappa< 1, the frequency ff first decreases and then increases with η\eta, whereas for κ>1\kappa> 1, the trend is reversed. Notably, there exists a balance point at which f/fL=1f/f_L = 1 for every value of κ\kappa. This is particularly interesting because one can select the length and width of an overhung or T-shaped cantilever such that it yields the same torsional frequency as a rectangular one. In other words, these points could serve as a reference for designing width-varying cantilevers.

Figure 7. (a) and (b) First torsional mode and (c) and (d) second torsional mode frequencies (ff normalized to the rectangular cantilever frequency (fLf_L as functions of normalized overhang length (η=l0/L\eta= l_0/L and coupling stiffness (βl\beta_l). Panels (a) and (c) show frequency trends across η\eta for varying κ=w/a0\kappa= w/a_0, while (b,d) highlight cross-sections at specific κ\kappa values (labeled). T-shaped cantilevers (κ<1\kappa< 1, red dashed lines) exhibit frequency enhancement with increasing η\eta, whereas overhang-shaped cantilevers (κ>1\kappa> 1, violet/green lines) display frequency reduction. Critical balance points (f/fLf/f_L indicate geometries where width-varying cantilevers match the torsional frequency of rectangular counterparts (κ=1\kappa= 1, black line). Non-monotonic shifts in ff with βl\beta_l suggest tunable sensitivity via geometric and interaction parameter adjustments..

Increasing the coupling stiffness β\beta causes the frequency to change more rapidly. For example, in the first mode [see Figure 7(b)], the curve intersects the f/fL=1f/f_L = 1 line earlier and then either increases (for κ<1\kappa< 1) to reach a maximum (as shown by the red dashed and blue dotted lines), or decreases (for κ>1\kappa> 1) to reach a minimum (violet long-dashed and green dash-dotted lines). For higher modes, additional extrema may appear, following a trend similar to that shown in Figure 5.

The sensitivity is defined as the change in frequency with respect to the interaction strength[7],

S=∂ω∂βl=∂ω∂γ∂γ∂βl=∂ω∂γ(−∂C/∂βl∂C/∂γ).(13)S = \frac{\partial\omega}{\partial\beta_l} = \frac{\partial\omega}{\partial\gamma}\frac{\partial\gamma}{\partial\beta_l} = \frac{\partial\omega}{\partial\gamma}\left(-\frac{\partial C/\partial\beta_l}{\partial C/\partial\gamma}\right). \tag*{(13)}

Here, the frequency of the beam is computed by

ω=γGJρIp.(14)\omega= \gamma\sqrt{\frac{GJ}{\rho I_p}}. \tag*{(14)}

Then, the normalized torsional sensitivity is obtained.

σT=κ2sin⁡[γ(1−η)]cos⁡(γηκ)+cos⁡[γ(1−η)]sin⁡(γηκ)D,(15)\sigma_T = \frac{\kappa^2 \sin[\gamma(1-\eta)]\cos(\gamma\eta\kappa) + \cos[\gamma(1-\eta)]\sin(\gamma\eta\kappa)}{D}, \tag*{(15)}

where

D=cos⁡[γ(1−η)]{κ[−βlη+(−1+βl(−1+η))κ]cos⁡(γηκ)+γ[1+η(−1+κ3)]sin⁡(γηκ)}+sin⁡[γ(1−η)]{γκ[η+κ−ηκ]cos⁡(γηκ)+[1+βl+βlη(−1+κ3)]sin⁡(γηκ)}.(16)D = \cos\left[\gamma(1-\eta)\right]\left\{\kappa\left[-\beta_l\eta+(-1+\beta_l(-1+\eta))\kappa\right]\cos(\gamma\eta\kappa)+\gamma\left[1+\eta(-1+\kappa^3)\right]\sin(\gamma\eta\kappa)\right\} +\sin\left[\gamma(1-\eta)\right]\left\{\gamma\kappa\left[\eta+\kappa-\eta\kappa\right]\cos(\gamma\eta\kappa)+\left[1+\beta_l+\beta_l\eta(-1+\kappa^3)\right]\sin(\gamma\eta\kappa)\right\}. \tag*{(16)}

The normalized torsional modal sensitivity is shown in Figure 8: (a) κ=1\kappa=1 for the rectangular, (b) κ=0.5\kappa=0.5 for the T-shaped, (c) κ=2.0\kappa=2.0 for the overhang-shaped, and (d) κ=3\kappa=3 for the wider overhang-shaped cantilevers. Here, η=0.2\eta=0.2 is used. It is recognized that the formulation of the sensitivity of a rectangle cantilever has been obtained if the geometric ratios were set κ=1\kappa=1 or η=0\eta=0, and the analytical calculation of Turner et al. is realized[7].

Figure 8. Sensitivity σT\sigma_T of the first four torsional modes for various value of κ\kappa. (a) κ=1\kappa=1 (rectangular cantilever). (b) κ=0.5\kappa=0.5 (T-shaped cantilever). (c) and (d) κ>1\kappa>1 (overhang-shaped cantilevers). For the overhang-shaped cantilevers, σT\sigma_T reduces with βl\beta_l faster for wider overhang width κ\kappa. Here, η=0.2\eta=0.2 is used.

First, a similar behavior in the modal sensitivity (σT\sigma_{T}) of a rectangular cantilever, as reported by Turner et al.[7], is reproduced in Figure 8(a), with the note that σT\sigma_{T} values here are slightly higher due to the use of a longer cantilever length of L=350 μmL = 350\ \mu\mathrm{m} [Turner used a 200 μm\mu\mathrm{m}-long cantilever].

For T-shaped cantilevers [Figure 8(b)] σT\sigma_{T} is slightly modified, whereas for overhang-shaped cantilevers [Figure 8(c)–Figure 8(d)] it is significantly altered. The σT\sigma_{T} of the first mode (black solid line) decreases more rapidly than those of the higher modes, while the σT\sigma_{T} of the fourth mode remains relatively stable over a wide range of βl\beta_l (green dash-dotted line). Notably, at low βl\beta_l, the third mode (blue dotted line) shows increased sensitivity, surpassing that of the second mode—an inversion compared to the conventional sensitivity order σTmode 1>σTmode 2>σTmode 3>σTmode 4\sigma_{T}^{\mathrm{mode}\ 1} > \sigma_{T}^{\mathrm{mode}\ 2} > \sigma_{T}^{\mathrm{mode}\ 3} > \sigma_{T}^{\mathrm{mode}\ 4} seen in rectangular and T-shaped cantilevers.

Furthermore, an increase in sensitivity is observed only for the second mode within the range βl=1\beta_l = 1–1010. This differs from the typical trend, where sensitivity tends to increase over a wider range, typically βl=1\beta_l = 1–100100, depending on the mode number, before dropping rapidly to zero as βl→103\beta_l \to10^{3}, as shown in Ref.[7] for torsional modes and in Refs.[19, 29] for flexural modes.

To further enhance the dynamic response and sensitivity of torsional modes, cantilevers equipped with extended sidewall probes could be employed, as demonstrated in Ref.[30]. These have shown interesting behavior depending on the geometry of the extended probe[9]. We intend to explore this topic in a future study.

Conclusions

In this study, we analytically derived the frequency characteristic equations and modal sensitivities for the torsional modes of overhang- and T-shaped cantilevers. Our results reveal significant and effective changes in both mode shape and frequency as functions of the overhang length, providing a versatile framework for selecting dimensional parameters to achieve specific performance characteristics. Notably, we presented a detailed analysis of the modal sensitivity of these cantilevers for the first time.

By modeling the tip–sample interaction as a linear lateral spring, we introduced a tunable coupling stiffness parameter βl\beta_l that directly affects the torsional response. We showed that increasing βl\beta_l leads to a non-monotonic shift in the modal frequencies, with critical balance points where the torsional frequency of width-varying cantilevers matches that of rectangular ones—offering practical benchmarks for cantilever design. The influence of βl\beta l on modal sensitivity was found to be strongly geometry-dependent, particularly for overhang-shaped cantilevers where unconventional sensitivity ordering emerged. This behavior suggests that geometric modifications can be strategically used to enhance or suppress sensitivity for specific modes.

The close match with Sadewasser’s experiments—a widely cited benchmark for AFM cantilever dynamics—validates our model’s ability to capture real-world torsional-flexural coupling without relying on empirical fitting. Minor deviations (<5%< 5\%) may arise from differences in material properties (e.g., silicon vs. silicon nitride) or edge effects in Sadewasser’s fabrication process.

Our analytical findings not only align with previous studies for rectangular cantilevers[7], but also extend the analysis to geometries that had not been previously explored in the context of torsional modes. These insights offer valuable guidance for experimentalists in designing cantilever structures with tailored frequencies and sensitivities, enabling highly sensitive measurements across a range of applications. Future work may consider incorporating extended sidewall probes, which have shown promising results in improving dynamic behavior and sensitivity[9, 30].

Acknowledgements

We thank Amir F. Payam (Ulster University) for fruitful discussion and encouragement.

References

References

  1. [1]K. C. Neuman and A. Nagy, “Single-molecule force spectroscopy: optical tweezers, magnetic tweezers and atomic force microscopy,” Nat. Methods 5, 491–505 (2008).DOI
  2. [2]M. Sajjadi, H. N. Pishkenari, and G. Vossoughi, “Dynamic modeling of trolling-mode AFM: Considering effects of cantilever torsion, nanoneedle flexibility and liquid-nanoneedle interactions,” Ultramicros. 182, 99–111 (2017).DOI
  3. [3]M. Karimpour, R. Ghaderi, and F. Raeiszadeh, “Vibration response of piezoelectric micro-cantilever as ultrasmall mass sensor in liquid environment,” Micron 101, 213–220 (2017).DOI
  4. [4]⁴B. Rezapour, M. A. F. Araghi, and H. Vázquez-Leal, “Application of homotopy perturbation method for dynamic analysis of nanotubes delivering nanoparticles,” J. Vib. Control 27, 802–814 (2021).DOI
  5. [5]⁵L. T. Dat, C. C. Nguyen, N. D. Vy, and A. F. Payam, “Tuning the flexural frequency of overhang-/ t-shaped microcantilevers for high harmonics,” Jpn. J. Appl. Phys. 62, 107002 (2023).DOI
  6. [6]⁶N. D. Vy and T. Iida, “Nonlinear analysis of sub-millikelvin optomechanical cooling for extremely low noise quantum measurement,” Appl. Phys. Express 8, 032801 (2015).DOI
  7. [7]⁷J. A. Turner and J. S. Wiehn, “Sensitivity of flexural and torsional vibration modes of atomic force microscope cantilevers to surface stiffness variations,” Nanotechnology 12, 322 (2001).DOI
  8. [8]⁸K. Heinze, O. Arnould, J.-Y. Delenne, V. Lullien-Pellerin, M. Ramonda, and M. George, “On the effect of local sample slope during modulus measurements by contact-resonance atomic force microscopy,” Ultramicros. 194, 78–88 (2018).DOI
  9. [9]⁹A. F. Payam and N. Duy Vy, “Dynamic analysis of flexural vibration mode of an atomic force microscope cantilever with a sidewall probe in liquid,” Microsc. Res. Tech. 84, 782–788 (2021).DOI
  10. [10]¹⁰L. B. Sharos, A. Raman, S. Crittenden, and R. Reifenberger, “Enhanced mass sensing using torsional and lateral resonances in microcantilevers,” Applied Physics Letters 84, 4638–4640 (2004), https://pubs.aip.org/aip/apl/article-pdf/84/23/4638/18589520/4638_1_online.pdf.DOI
  11. [11]¹¹J. A. Plaza, K. Zinoviev, G. Villanueva, M. Álvarez, J. Tamayo, C. Domínguez, and L. M. Lechuga, “T-shaped microcantilever sensor with reduced deflection offset,” Appl. Phys. Lett. 89, 094109 (2006).DOI
  12. [12]¹²J. E. Sader, J. A. Sanelli, B. D. Adamson, J. P. Monty, X. Wei, S. A. Crawford, J. R. Friend, I. Marusic, P. Mulvaney, and E. J. Bieske, “Spring constant calibration of atomic force microscope cantilevers of arbitrary shape,” Rev. Sci. Instrum. 83, 103705 (2012).DOI
  13. [13]¹³G. Zhang, L. Zhao, Z. Jiang, S. Yang, Y. Zhao, E. Huang, X. Wang, and Z. Liu, “Surface stress-induced deflection of a microcantilever with various widths and overall microcantilever sensitivity enhancement via geometry modification,” J. Phys. D: Appl. Phys. 44, 425402 (2011).DOI
  14. [14]L. T. Dat, V. N. T. Pham, N. D. Vy, and A. F. Payam, “Frequency equation and semi-empirical mechanical coupling strength of microcantilevers in an array,” Microsc. Res. Tech. 85, 3237–3244 (2022).DOI
  15. [15]Q. Chen, L. Huang, and Y.-C. Lai, “Chaos-induced intrinsic localized modes in coupled microcantilever arrays,” Appl. Phys. Lett. 92, 241914 (2008), https://pubs.aip.org/aip/apl/article-pdf/doi/10.1063/1.2946494/14396120/241914_1_online.pdf.DOI
  16. [16]T. M. Huber, E. T. Ofstad, S. M. Barthell, A. Raman, and M. Spletzer, “Excitation of vibrational eigenstates of coupled microcantilevers using ultrasound radiation force,” Int’l Design Eng. Tech. Conf. and Computers Infor. Eng. Conf. 4: 20th Int’l Conf. Design Theory and Methodology; Second Int’l Conf. Micro- and Nanosys., 737–741 (2008), https://asmedigitalcollection.asme.org/IDETC-CIE/proceedings-pdf/IDETC-CIE2008/43284/737/4578299/737_1.pdf.DOI
  17. [17]N. Dick and S. Krylov, “Modal behavior of microcantilevers arrays with tunable electrostatic coupling,” Actuators 12 (2023), 10.3390/act12100386.DOI
  18. [18]A. F. Payam, W. Trewby, and K. Voitchovsky, “Determining the spring constant of arbitrarily shaped cantilevers in viscous environments,” Appl. Phys. Lett. 112, 083101 (2018).DOI
  19. [19]N. D. Vy, A. Morelli, V. N. Pham, D. Finlay, and A. F. Payam, “Dynamics analysis of width-varying microcantilevers: Interplay between eigenfrequencies, contact stiffness and interaction forces,” Int. J. Solids Struct. 259, 112027 (2022).DOI
  20. [20]S. Sadewasser, G. Villanueva, and J. A. Plaza, “Modified atomic force microscopy cantilever design to facilitate access of higher modes of oscillation,” Rev. Sci. Instrum. 77, 073703 (2006), https://pubs.aip.org/aip/rsi/article-pdf/doi/10.1063/1.2219738/13815552/073703_1_online.pdf.DOI
  21. [21]S. Z. Mohammadi, M. Moghadam, and H. N. Pishkenari, “Dynamical modeling of manipulation process in trolling-mode afm,” Ultramicros. 197, 83–94 (2019).DOI
  22. [22]L. T. Dat, V. Lan, and N. D. Vy, “Exact mode shapes of t-shaped and overhang-shaped microcantilevers,” Commun. in Phys. 30, 301 (2020).DOI
  23. [23]L. Meirovitch, “Analytical methods in vibrations.” Macmillan series in applied mechanics (1967).
  24. [24]W. Weaver Jr, S. P. Timoshenko, and D. H. Young, Vibration problems in engineering (John Wiley & Sons, 1991).
  25. [25]H. Etayash and T. Thundat, “Microcantilever chemical and biological sensors,” in Encyclopedia of Nanotechnology, edited by B. Bhushan (Springer Netherlands, Dordrecht, 2014) pp. 1–9.
  26. [26]A. W. McFarland, M. A. Poggi, L. A. Bottomley, and J. S. Colton, “Characterization of microcantilevers solely by frequency response acquisition,” J. Micromecha. Microeng. 15, 785 (2005).DOI
  27. [27]C. M. Hoang, N. D. Vy, L. T. Dat, and T. Iida, “Enhancing amplitudes of higher-order eigenmodes of atomic force microscope cantilevers by laser for better mass sensing,” Jpn. J. Appl. Phys. 56, 06GK05 (2017).DOI
  28. [28]M. Abbasi and A. Karami Mohammadi, “Study of the sensitivity and resonant frequency of the torsional modes of an AFM cantilever with a sidewall probe based on a nonlocal elasticity theory,” Microsc. Res. Tech. 78, 408–415 (2015).DOI
  29. [29]A. F. Payam, “Sensitivity of flexural vibration mode of the rectangular atomic force microscope micro cantilevers in liquid to the surface stiffness variations,” Ultramicrosc. 135, 84–88 (2013).DOI
  30. [30]G. Dai, H. Wolff, T. Weimann, M. Xu, F. Pohlenz, and H.-U. Danzebrink, “Nanoscale surface measurements at sidewalls of nano- and micro-structures,” Measurement Science and Technology 18, 334 (2007).DOI

Paper details

vlnc:W_bwh9dgz4
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents