betaFeedback

WorksPhysics and Astronomy

Design of auxetic cellular structures for in-plane response through out-of-plane actuation of stimuli-responsive bridge films

Abstract

In this work, we propose novel designs of cellular structures exhibiting unconventional in-plane actuation responses to external stimuli. We strategically introduce stimuli-responsive bilayer bridge films within conventional honeycombs to achieve the desired actuation. The films are incorporated such that, in response to an external field (thermal, electric, chemical, etc.), the bridge film bends out-of-plane, activating the honeycomb in the plane. The conventional out-of-plane deformation of the bridge film can lead to interesting and unconventional actuation in the plane. An analytical model of this coupled unit cell behaviour is developed using curved beam theory, and the model is validated against finite element simulations. Several applications of such designs are presented. Unit cell architectures exhibiting both positive and negative macroscopic actuation are proposed, and the criterion for achieving such actuation is derived analytically. Furthermore, we demonstrate that by altering the topology, unidirectional and bidirectional negative actuation can be achieved. We also propose designs that result in the negative actuation of the structure with both monotonically increasing and monotonically decreasing stimuli. Finally, by combining two macroscopic structures with positive and negative actuation, we design efficient actuators/sensors that bend in the plane in response to a stimulus.

Introduction

Metamaterials are a class of materials that are engineered to exhibit unusual mechanical or physical properties not found in traditional materials [1] [2, 3]. These materials can be designed to have specific properties that are desirable for various applications [4–7]. One area of particular interest in the study of metamaterials is the development of materials with negative parameters of mechanical properties, which are not found in nature. Negative parameters of mechanical properties refer to values opposite in sign to what is typically observed in conventional materials. For example, negative thermal expansion (NTE) refers to a material contracting rather than expanding upon heating. While such behaviour is rare in nature, recent developments in lattice metamaterials have focused on optimizing mesoscale architecture to engineer materials which exhibit unusual macroscopic behaviour such as near zero expansion [8–10] and negative thermal expansion [11–21]. This counterintuitive behaviour has found applications in various fields, including the development of temperature-stable components for aerospace and electronics applications [22–26]. Similarly, metamaterials have been designed to obtain negative swelling behaviour [27–32] and negative hygroscopic expansion [33–37], which have applications in the development of humidity-sensitive devices and materials.

Previous studies have achieved a negative (or reversed stimuli) response using one of two mechanisms. The first involves incorporating active components and clever kinematics to convert local axial expansions into macroscopic shrinkage. Examples of such designs include both two and three-dimensional structures formed using dual-material triangles [38–41] and dual-material tetrahedrons [42, 43] respectively. The second mechanism involves introducing bi-material strips to replace certain members of the structure, resulting in bending and a negative response [18, 44–46]. While the former design offers high relative stiffness, it provides a limited range of negative expansion, whereas the latter offers a larger negative expansion but a lower stiffness.

To address the limitations of the two approaches mentioned above, we propose a novel design strategy that leverages out-of-plane deformation by strategically introducing stimuli-responsive bi-material bridge films into conventional lattice structures. This design allows for a greater macroscopic in-plane negative expansion range while maintaining high relative stiffness. Moreover, the actuation mechanism is out-of-plane, and only its projection into the plane governs the in-plane response, expanding the design space significantly. As such, our proposed design offers the capability to exhibit curious and unconventional behaviour, such as negative responses to both positive and negative changes in the stimulus, unidirectional or bidirectional negative expansion, etc. Moreover, we can achieve forward and reverse responses with a simple orientation change of the bridge

Email addresses: [email protected] (Anirudh Chandramouli), [email protected] (Sri Datta Rapaka), [email protected] (Ratna Kumar Annabattula) film.

Cellular structures with stimuli-responsive bridge films

The proposed designs build on conventional cellular structures with well-developed in-plane mechanical behaviour. Stimuli-responsive bridge films are strategically introduced, connecting the vertices of the unit cells as shown in Figure 1. These bridge films are designed and oriented to deform in the out-of-plane direction. Accordingly, the bridge films comprise a stimuli-responsive active layer (which responds conventionally and expands in response to an increase in the external field) and a nonresponsive passive layer stacked perpendicular to the plane of the unit cell. In response to an external stimulus, the bilayer bends out-of-plane due to a strain mismatch along its thickness, thereby inducing the unit cell in-plane actuation. Since only the ends of the films are connected to the vertices of the unit cell, the actuation of the unit cell depends on the projection of the film deformation onto the plane. Consequently, unconventional macroscopic in-plane responses to stimuli can be obtained through appropriate material properties and geometric considerations.

Schematic illustration of the unit cell of the proposed design with stimuli-responsive bilayer bridge films introduced between the vertices of a conventional auxetic honeycomb structure

Figure 1. Schematic illustration of the unit cell of the proposed design with stimuli-responsive bilayer bridge films introduced between the vertices of a conventional auxetic honeycomb structure.

Bridge film actuation

The bilayer bridge film is assumed to respond to external stimuli such that the strain varies linearly with the external field. In other words, ϵ=αΔT\epsilon= \alpha\Delta T, where ΔT\Delta T is the applied field and α\alpha is the coefficient of expansion. The coefficient of expansion of the passive layer of the film and the unit cell is assumed to be negligibly small. The response of the bilayer film, in isolation, to an external field is well known [47]. With an increase in the applied field, the film both expands and bends out-of-plane with constant curvature along its length and is given by [47]

u=1R=αa−αptp+ta2+EpIp+EaIatp+ta(1Eptp+1Eata)ΔT≔cΔT,(1)u = \frac{1}{R} = \frac{\alpha_a-\alpha_p}{\frac{t_p+t_a}{2}+\frac{E_pI_p+E_aI_a}{t_p+t_a}\left(\frac{1}{E_pt_p}+\frac{1}{E_at_a}\right)}\Delta T \coloneqq c\Delta T, \tag*{(1)}

where RR is the radius of curvature of the film, EaE_a is the modulus of elasticity of the active layer, tat_a is its thickness, IaI_a is its area moment of inertia, and αa\alpha_a is the coefficient of expansion. EpE_p, tpt_p, IpI_p, and αp\alpha_p are the corresponding parameters of the passive layer. The projection of this deformation onto the plane, seen as a change in the in-plane length of the film, is given by

δl=2Rsin⁡(li(1+ϵp)2R)−li=sin⁡(li[1+ϵp]cΔT/2)cΔT/2−li,(2)\delta l = 2R\sin\left(\frac{l_i(1+\epsilon_p)}{2R}\right)-l_i = \frac{\sin\left(l_i[1+\epsilon_p]c\Delta T/2\right)}{c\Delta T/2}-l_i, \tag*{(2)}

where cc is as defined in Eq. (1), lil_i is the initial length of the film and ϵp\epsilon_p is the strain in the passive layer at the surface to be attached to the unit cell. This change can either be an increase or a decrease in length. Note that αp→αa⟹c→0\alpha_p \to\alpha_a \Longrightarrow c \to0 and therefore δl=liϵp\delta l = l_i\epsilon_p resulting in a monotonic increase in the length with the applied field. However, for αp≠αa\alpha_p \ne\alpha_a, it is evident that δl\delta l will eventually be negative for large ΔT\Delta T resulting in an eventual in-plane shrinkage. However, to ensure an initial shrinkage,

dδldΔT∣ΔT=0<0⟹αp≤(5EaEp−Ea2Ep(19Ea+Ep))αa.(3)\left.\frac{d\delta l}{d\Delta T}\right|_{\Delta T=0}<0 \Longrightarrow\alpha_p \leq\left(\frac{5E_aE_p-E_a^2}{E_p(19E_a+E_p)}\right)\alpha_a. \tag*{(3)}

Note that for materials which do not satisfy the above relationship, the unit cell expands on heating (at least, initially). Therefore, by choosing the material parameters appropriately, both negative and positive actuation of the unit cell can be achieved in response to an increasing field. Since most materials expand with an increasing stimulus field, the more interesting case of negative response will be the primary focus of this work.

Analytical model

As discussed in § 2.1, the out-of-plane bending of the bridge film causes an in-plane change in its length. However, since the bridge film is attached to the vertices of the unit cell, the unit cell resists this change in length. Furthermore, since the film is assumed to be glued to the vertices, the unit cell also offers moment resistance to a change in the film angle at its ends. An analytical model is developed to study this coupled response.

The bridge films at the inner and outer ends of the unit cells are assumed to be identical and mirror-symmetric about the X-Y plane as shown in Figure 1. Therefore, a half-cell model of the unit cell coupled with a single bridge film is developed. Furthermore, the in-plane mechanics of the conventional unit cell is modelled through a continuum approximation following the work of Gibson and Ashby [48]. Additionally, assuming small strains (and geometry change), the in-plane mechanism is idealized as a translation spring (attached to the edges on the inner surface of the bilayer film) and two torsion springs (attached to both ends of the film and, in turn, coupled to the ground). The schematic of this simplification is shown in Figure 2(a). The stiffness of the translation spring, kk, for a hexagonal honeycomb is given as [48]

Schematic illustration of the spring approximation of the unit cell and curved composite bilayer

Figure 2. (a) Schematic of the spring approximation of the unit cell. The translational response is captured by a linear spring whose stiffness is derived from [48], and the torsional response is replaced by two torsional springs of stiffness, τ\tau. (b) Curved composite bilayer, initially at equilibrium under the combined action of a stimuli field differential and resisting moment, subject to spring forces and moments

k=Ehwtw3l3cos⁡2θ,(4)k = \frac{E_hw_tw^3}{l^3\cos^2\theta}, \tag*{(4)}

where ll is the inclined wall length as shown in Figure 1, ww is the out-of-plane width, twt_w is the wall thickness, θ\theta is the inclination angle, and EhE_h is the Young’s modulus of the unit cell material. Similarly, τ\tau is the stiffness of the equivalent torsional spring. An approximation of τ\tau can be found by assuming that the deformations caused due to moment are in the form of suitable polynomials. The coefficients are subsequently found using strain energy minimization and, in turn, used to derive τ\tau. The details of the derivation and the analytical expression for τ\tau are presented in the supplementary file.3

Using the above simplifications, the response of the coupled system is found as follows. Firstly, the bending moment arising due to the strain mismatch in the bilayer and the resisting moment offered by the torsional springs are solved for equilibrium. It is assumed that the total deformation of the system can be seen as a superposition of this pure bending deformation and the deformations arising from the force in the translational spring.

Firstly, we derive the equilibrium configuration of the bilayer and torsional springs. Since the system is such that the bending moment will be constant through the length, the curvature will also be constant. Let the corresponding radius of curvature at the equilibrium be ρ\rho and the subtended angle be ϕ\phi. Then, we have

ρ=EcIcM=EcIcτϕ+Mth(5)\rho= \frac{E_c I_c}{M} = \frac{E_c I_c}{\tau\phi+ M_{\mathrm{th}}} \tag*{(5)}

where EcE_c and IcI_c are the effective Young’s modulus and area moment of inertia of the composite bilayer, respectively and Mth=EcIc/RM_{\mathrm{th}} = E_c I_c/R is the equivalent thermal moment. Since the composite bar is in pure bending, the length of the neutral axis remains constant. Therefore, we have ρϕ=Rθ\rho\phi= R\theta. Upon substitution of ρ=Rθ/ϕ\rho= R\theta/\phi in Eq. (5), we have

Rθϕ=EcIcτϕ+Mth(6)\frac{R\theta}{\phi} = \frac{E_c I_c}{\tau\phi+ M_{\mathrm{th}}} \tag*{(6)}
τRθ+EcIcθϕ=EcIc(7)\tau R\theta+ \frac{E_c I_c\theta}{\phi} = E_c I_c \tag*{(7)}
τRθϕ+EcIcθ=EcIcϕ(8)\tau R\theta\phi+ E_c I_c\theta= E_c I_c\phi \tag*{(8)}
⟹ϕ=EcIcθEcIc−τRθ(9)\Longrightarrow\phi= \frac{E_c I_c\theta}{E_c I_c - \tau R\theta} \tag*{(9)}
ρ=EcIcR−τR2θEcIc(10)\rho= \frac{E_c I_c R - \tau R^2\theta}{E_c I_c} \tag*{(10)}

This equilibrium configuration, characterized by ρ\rho and ϕ\phi, is assumed to be the initial configuration of a curved beam which is then subjected to a splitting force (FyF_y) and moment (MzM_z) as shown in Figure 2(b). Analyzing the beam in polar coordinates and considering an infinitesimal segment dψd\psi at an angle of ψ\psi from the centre, we have [49]

1ρdudψ−vρ=−Fyρcos⁡ϕ−MzρAcEc,(11)\frac{1}{\rho}\frac{du}{d\psi}-\frac{v}{\rho}=\frac{-F_y\rho\cos\phi-M_z}{\rho A_cE_c}, \tag*{(11)}
1ρ2d2vdψ2+vρ2=Fyρ(cos⁡ψ−cos⁡ϕ)−MzEcIc,(12)\frac{1}{\rho^2}\frac{d^2v}{d\psi^2}+\frac{v}{\rho^2}=\frac{F_y\rho(\cos\psi-\cos\phi)-M_z}{E_cI_c}, \tag*{(12)}

where Ac=(ApEp+AaEa)/EcA_c=(A_pE_p+A_aE_a)/E_c is the effective area of the composite bilayer, uu and vv are the tangential and radial displacements respectively. The above equations are solved with the boundary conditions v∣ψ=0=0v|_{\psi=0}=0, 1ρdvdψ∣ψ=0=0\frac{1}{\rho}\frac{dv}{d\psi}|_{\psi=0}=0, and u∣ψ=0=0u|_{\psi=0}=0 that represent the symmetric deformation of the curved composite beam, resulting in

u(ψ)=14ϕ(ρ3(2ρFysin⁡2ψ+(4Mz+2ρFy)sin⁡ψ−4Mzψ)EcIc−6ρFyψcos⁡ψEcIc−4ψ(Mz+ρ2Fycos⁡ψ)AcEc),(13)u(\psi)=\frac{1}{4\phi}\left(\frac{\rho^3(2\rho F_y\sin2\psi+(4M_z+2\rho F_y)\sin\psi-4M_z\psi)}{E_cI_c}-\frac{6\rho F_y\psi\cos\psi}{E_cI_c}-\frac{4\psi(M_z+\rho^2F_y\cos\psi)}{A_cE_c}\right), \tag*{(13)}
v(ψ)=ρ24EcIc(4ρFycos⁡2ψ+4(Mz−ρFy)cos⁡ψ−4Mz+2ρFyψsin⁡ψ),(14)v(\psi)=\frac{\rho^2}{4E_cI_c}\left(4\rho F_y\cos^2\psi+4(M_z-\rho F_y)\cos\psi-4M_z+2\rho F_y\psi\sin\psi\right), \tag*{(14)}
dϕ(ψ)=ρEcIc(Mzψ+ρFyψcos⁡ψ−ρFysin⁡ψ).(15)d\phi(\psi)=\frac{\rho}{E_cI_c}(M_z\psi+\rho F_y\psi\cos\psi-\rho F_y\sin\psi). \tag*{(15)}

Therefore, the vertical deformation (yy) of the curved beam from the equilibrium configuration is given by

y=2u(ϕ/2)cos⁡(ϕ/2)−2v(ϕ/2)sin⁡(ϕ/2).(16)y=2u(\phi/2)\cos(\phi/2)-2v(\phi/2)\sin(\phi/2). \tag*{(16)}

Note that the external force (FyF_y) and moment (MzM_z) can only arise from the reaction forces from the translational and torsional springs. Therefore, the translational deformation (yy) and angular deformation (dϕd\phi) arising from these spring forces and moments must be compatible with the spring equations. Thus, we have

Fy=−kδ∗where δ∗=li−2ρsin⁡(ϕ/2)−y(17)F_y=-k\delta^* \quad\text{where }\delta^*=l_i-2\rho\sin(\phi/2)-y \tag*{(17)}
Mz=−τdϕ(18)M_z=-\tau d\phi \tag*{(18)}

Note that MzM_z is the moment on the bridge film over the equilibrium configuration defined by Eq. (10) and not the total external moment on the bridge film. The above system of equations (Eqs. (16) to (18)) are solved for displacement and forces in the spring. Accordingly, the vertical deformation of the unit cell as a function of temperature is given by

δ∗=li−2ρsin⁡(ϕ/2)−kρ3(li−2ρsin⁡(ϕ/2))(ρτβ+2EcIc(2ϕ−α))kρ4β+2EcIc(ρϕ(2kρ2+τ)+kρ3(α+2EcIc)),(19)\delta^*=l_i-2\rho\sin(\phi/2)-\frac{k\rho^3(l_i-2\rho\sin(\phi/2))(\rho\tau\beta+2E_cI_c(2\phi-\alpha))}{k\rho^4\beta+2E_cI_c(\rho\phi(2k\rho^2+\tau)+k\rho^3(\alpha+2E_cI_c))}, \tag*{(19)}

where α=ϕcos⁡ϕ−3sin⁡ϕ\alpha=\phi\cos\phi-3\sin\phi and β=(−4+ϕ2+4cos⁡ϕ+ϕsin⁡ϕ)\beta=(-4+\phi^2+4\cos\phi+\phi\sin\phi). Here, δ∗\delta^* is the total vertical deformation of the combined system from the initial configuration. Further, the vertical force

applied by the bilayer on the unit cell is given by

Fy=−2EcIck(l−2ρsin⁡(ϕ/2))(ρϕτ+2EcIc)kρ4β+2EcIc(ρϕ(2kρ2+τ)+kρ3α+2EcIc).(20)F_y=-\frac{2E_cI_ck(l-2\rho\sin(\phi/2))(\rho\phi\tau+2E_cI_c)}{k\rho^4\beta+2E_cI_c(\rho\phi(2k\rho^2+\tau)+k\rho^3\alpha+2E_cI_c)}. \tag*{(20)}

Similarly, the corresponding moment applied is given by

Mz=−2kρ2τ(ϕcos⁡(ϕ/2)−2sin⁡(ϕ/2))(l−2EcIcρsin⁡(ϕ/2))kρ4β+2EcIc(ρϕ(2kρ2+τ)+kρ3α+2EcIc).(21)M_z=-\frac{2k\rho^2\tau(\phi\cos(\phi/2)-2\sin(\phi/2))(l-2E_cI_c\rho\sin(\phi/2))}{k\rho^4\beta+2E_cI_c(\rho\phi(2k\rho^2+\tau)+k\rho^3\alpha+2E_cI_c)}. \tag*{(21)}

Validation of the analytical model

The developed analytical model is validated against finite element simulations of the unit cell. A single unit cell of the metamaterial (with the bridge films) is modelled in isolation, and its response is simulated. Both the unit cell and the bilayer are modelled using shell elements with reduced integration in Abaqus [50]. For the purpose of demonstration, the unit cell and the passive layer are assumed to be made of the same material. The geometric and material properties of the proposed unit cell are as defined in Table 1. The external stimulus is applied in the form of a temperature field to the model. Boundary conditions are applied, constraining the left surface of the unit cell in the XX direction and a point on the surface in the YY and ZZ directions to prevent rigid body motions. The response of the system is compared with the analytical predictions.

Young’s modulus of active material (EaE_a)3 GPa
Young’s modulus of passive material (EpE_p)3 GPa
Poisson’s ratio (νa,νp\nu_a, \nu_p)0
Coefficient of expansion of active layer (αa\alpha_a)2×10−3 ∘C−12 \times10^{-3}\ ^\circ\mathrm{C}^{-1}
Coefficient of expansion of passive layer (αp\alpha_p)1×10−10 ∘C−11 \times10^{-10}\ ^\circ\mathrm{C}^{-1}
Inclined wall length (ll)4 mm
Vertical wall length (hh)8 mm
Hexagonal inclination angle (θ\theta)−30∘-30^\circ
Cell wall thickness (twt_w)0.13 mm
Width of the bilayer bridge film (dd)0.8 mm
Out-of-plane width of the unit cell (ww)4 mm
Thickness of the bilayer bridge film (ta,tpt_a, t_p)0.25 mm

Table 1. Geometric and material properties used in the model

The vertical in-plane shrinkage (δ∗\delta^*) of the bilayer from the FEA simulations is plotted against the applied temperature field in Figure 3 along with the analytical predictions. It is evident that the analytical model accurately captures the response of the unit cell over a large domain. This shrinkage of the bilayer actuates the unit cell by pulling the vertices of the hexagon together. Note that while the vertices are drawn together, the length of the side walls remains unaffected. Moreover, it is evident that the response is not symmetric for positive and negative fields. This is due to two reasons. Firstly, although the curvature of the film depends only on the magnitude of the applied field, the subtended angle (and consequently the change in length) depends on the sign of the applied field. Secondly, and more significantly, the thickness affects the response since the film is attached to the unit cell on its inner surface. During bending, the strain on the inner and outer surfaces of the film are not identical. This effect, however, diminishes as the ratio of length to thickness grows large. The horizontal response of the unit cell is due to the effective Poisson effect of the metamaterial. The Poisson’s ratio of a hexagonal unit cell is given by [48]

Comparison of FEA and analytical predictions for vertical deformation

Figure 3. Comparison of the FEA results with analytical predictions with respect to the vertical deformation of the proposed unit cell under a temperature differential.

νYX=(h/l+sin⁡θ)sin⁡θcos⁡2θ.(22)\nu_{YX}=\frac{(h/l+\sin\theta)\sin\theta}{\cos^2\theta}. \tag*{(22)}

For the auxetic structure chosen, the negative Poisson’s ratio implies that the vertical shrinkage results in a shrinkage along the horizontal direction. The deformed configuration of the unit cell at ±50 ∘C\pm50\,^\circ\mathrm{C} is overlaid in Figure 3. It is interesting to note that both increasing and decreasing fields result in a shrinkage of the unit cell.

Results and discussions

In the previous section, a unit cell model was proposed that shrinks in response to an increasing field. Cellular structures with varied macroscopic behaviours can be engineered using these cells as building blocks. In this section, several interesting applications of such designs are discussed.

Bi-directional negative actuation

As noted previously, the bridge film pulls the mid-vertices of the hexagonal unit cell closer together. The length of the side walls remains unchanged, but the horizontal distance between them shrinks as a consequence of the Poisson effect. A row of such cells will each deform individually, and their total horizontal deformation will be a sum of the individual deformations. In stacking these cells vertically, each row can be arranged such that the side walls of any row are attached to the bridge films above and below it, as shown in Figure 4(a). Consequently, each column is made of alternating side walls and bridge films. The total vertical deformation is, therefore, approximately equal to nδ∗/2n\delta^*/2, where nn is the number of columns. However, in arranging the rows as such, the side walls attached above and below the bridge films add additional moment resistance (in addition to τ\tau). This stiffens the unit cell and reduces the vertical shrinkage (and, in turn, the horizontal shrinkage).

Finite element simulations of the bi-directional negative expansion of the cellular structure and corresponding macroscopic strain variation

Figure 4. (a) Finite element simulations of the bi-directional negative expansion of the cellular structure under a temperature differential showing the deformed (green) and undeformed (grey) configuration at 70 °C and (b) the corresponding macroscopic strain variation in the bulk of the lattice structure.

Figure 4(a) presents the undeformed and deformed configuration of a 7×87 \times8 cellular structure modelled as described above. The deformed configuration is plotted for a temperature field of 70 ∘C70\,^\circ\mathrm{C}. Figure 4(b) presents the macroscopic strain variation in the bulk of the structure as a function of temperature. It is evident that the macroscopic response of the cellular structure is a bi-directional contraction with an increasing external field. Further, the strain along the horizontal and vertical at 70 ∘C70\,^\circ\mathrm{C} are found to be 0.0144 and 0.0146, respectively.

Uni-directional negative actuation

Since the side walls do not deform vertically, the rows of unit cells can be stacked such that each side wall connects to the corresponding wall of the rows above and below, as shown in Figure 5(a). This implies that the vertices remain unconnected and do not transmit their deformations vertically. Consequently, the height of the cellular structure remains unchanged. However, due to Poisson’s effect, the structure shrinks horizontally. Therefore, the structure actuates unidirectionally in response to an external stimulus. The deformed and undeformed configuration of a cellular structure with the above design is simulated in Abaqus and plotted in Figure 5(a). Figure 5(b) presents the corresponding macroscopic strain variation in the bulk of the structure as a function of temperature. Since the vertices are unconnected, there is no increase in the moment stiffness of the unit cells. This consequently leads to a larger actuation, and the horizontal strain is consequently greater for this case, while the macroscopic vertical strain is ≈0\approx0. At 70 °C, the horizontal strain is found to be 0.054.

Finite element simulations and corresponding macroscopic strain variation

Figure 5. (a) Finite element simulations of the uni-directional negative expansion of the cellular structure under a temperature differential showing the deformed (green) and undeformed (grey) configuration at 70 °C and (b) the corresponding macroscopic strain variation in the bulk of the lattice structure.

In-plane bridge film actuation

In the above design, vertical deformations were not transmitted since the vertices remained unconnected. In other words, the columns containing the stimuli-responsive bridge films were intermittent. Taking inspiration from the above mechanism of isolating the vertical deformations, these columns can be inverted - removing the bridge films within the unit cell and instead using bridge films connecting the vertices of one unit cell to that of the cell below and above it. Due to this inversion, an expanding film is required to achieve the same macroscopic response. Therefore, the bridge film could be introduced in-plane as a single active layer as shown in Figure 6(a). This design can achieve a similar unidirectional negative actuation in response to an increasing stimulus field. The actuation response of this design is modelled and simulated in Abaqus. The deformed and undeformed configurations are plotted in Figure 6(a), and the macroscopic strain variation as a function of temperature is plotted in Figure 6(b). It is evident that the local vertical expansions result in a macroscopic shrinkage along the horizontal, with the macroscopic height of the structure remaining unchanged. Moreover, the strain is slightly larger and is found to be 0.056 at 70 °C. However, it should be noted that the relative volume of the active material is significantly higher in this design. Further, it is noted from Figure 5(b) and Figure 6(b) that the out-of-plane design results in a nonlinear response in contrast to the in-plane design.

Finite element simulation with in-plane bridge film actuation and corresponding macroscopic strain variation

Figure 6. (a) Finite element simulation of the uni-directional negative expansion of the cellular structure under a temperature differential using in-plane bridge film actuation showing the deformed (green) and undeformed (grey) configuration at 70 °C and (b) the corresponding macroscopic strain variation in the bulk of the lattice structure.

Application as a bending actuator

The analytical model can be used to tune individual unit cells to achieve a varied set of responses. For instance, it can be shown that swapping the active and passive layers of the bridge film in the unit cell defined in Table 1 leads to an initial expansion of the vertices. This consequently results in a macroscopically positive thermal expansion. Such unit cells can be combined with macroscopic negative expansion unit cells to engineer a differential in the macroscopic strains of the different layers. This consequently results in the bending of the lattice structure. Moreover, since the curvature is directly proportional to the difference in the coefficients of thermal expansions of the two layers, more efficient bending actuation can be generated since the coefficient can be tuned to be highly negative as opposed to regular materials, wherein the expansion coefficient is typically positive. The response of such an arrangement to an applied external stimulus is shown in Figure 7. The structure bends with both decreasing (Figure 7(a)) and increasing (Figure 7(b)) stimulus fields, but in opposite directions.

Bending of the bilayer lattice under negative and positive temperature differentials

Figure 7. Bending of the bilayer lattice with its upper rows consisting of reversed response unit cells and its lower rows comprising regular response unit cells under (a) a negative temperature differential and (b) a positive temperature differential. The undeformed and deformed configurations are shown in grey and green, respectively.

Conclusion

In this work, we present a new design strategy that enables the creation of lattice structures with unconventional in-plane responses. The proposed approach involves incorporating stimuli-responsive bilayer bridge films into conventional lattice structures. These films are oriented in a way that directs the deformations out-of-plane, allowing for the introduction of actuators with a large design space while having minimal impact on the in-plane characteristics of the base lattice structure. An analytical model is developed using curved beam theory to better understand the response of unit cells comprising a conventional honeycomb and a stimuli response bridge film. This model considers the coupled response of the two systems, which can lead to complex and counter-intuitive behaviour. The analytical model is validated through finite element simulations, which confirm the accuracy of the model. Potential applications of such designs are demonstrated through various finite element simulations. For instance, it is shown that the proposed design strategy can lead to highly sensitive bending actuators, which can be useful in applications such as sensors and soft actuators in robotics. Moreover, directional stimuli-responsive actuators are also demonstrated, which can be useful in applications such as soft robots or adaptive structures. Such lattice structures may find utility in various industries, such as aerospace and electronic applications. In summary, the proposed design strategy is a promising approach to engineer lattice structures with unconventional in-plane responses. The analytical model and finite element simulations demonstrate the feasibility of the proposed approach and its potential applications.

Derivation of equivalent stiffness of torsion spring for a hexagonal honeycomb unit cell

The analytical study of the coupled response of a unit cell and an attached stimuli-responsive bridge film to an external stimuli field in this work involved approximating the unit cell response to a linear spring and two torsion springs. While the derivation of equivalent linear response to forces is available in the literature [1], the study of its response to moments at its vertex is not available; therefore, the equivalent torsional spring stiffness is not readily known. Therefore, in this section, the derivation of this stiffness is discussed3.

Consider the unit cell subject to a moment at its vertices, arising from the bending of the bridge film, as shown in Figure S1. Note that the resulting moment acts only at the vicinity of the vertex and thus cannot be analyzed as a simple bending problem of the entire unit cell section. Consequently, to derive its stiffness with respect to this moment, the system is idealized as presented in Figure S1. The vertical side walls show negligible deformations, and the inclined walls are split into three sections. Section II is the section that is directly attached to the bridge film, and sections I and III are mirror symmetric. The following assumptions are made in the derivations which follow

Hexagonal unit cell subject to moments at the vertices and simplified model of the response of a quarter section of the bridge film

Figure S1. (a) Hexagonal unit cell subject to moments at the vertices due to the bending of the attached stimuli responsive bridge film. The red and blue planes indicate planes of symmetry. (b) Simplified model of the response of a quarter section of the bridge film to an external moment about the X-axis at the vertex.

  • The total stiffness of the unit cell is seen as the stiffness of the three sections acting in parallel (additive).

  • The wall thickness is small, and thin plate approximations hold.

Since the moment acts across the entire cross-section of II, the stiffness of II can be calculated as τII=2EI/w\tau_{II}=2EI/w, where EE, II, and w/2w/2 are the Young’s modulus, area moment of inertia and length of section II respectively. The moment on section I acts only at the corner (refer to point 2 in Figure S1). To derive its stiffness, we consider this section in local coordinates (xyzxyz) with its origin at 4, wherein the section lies horizontally along the xyxy plane. The deformation of the plate due to the moment is approximated through suitable polynomials. The vertical displacement (uzu_z) along the zz-axis is assumed to be of the form

uz=(α+βy2+γy4)(μx+νx3),(23)u_z=(\alpha+\beta y^2+\gamma y^4)(\mu x+\nu x^3), \tag*{(23)}

where α\alpha, β\beta, γ\gamma, μ\mu and ν\nu are constants. Here, only even terms of the polynomial are considered along yy to make the function even (due to mirror symmetry - refer to the red plane in Figure S1) while it is assumed to be odd along xx. The boundary condition on 3-4 implies that (∂uz/∂x)∣x=0=0\left.(\partial u_z/\partial x)\right|_{x=0}=0, implying that μ=0\mu=0. Therefore, with a=ανa=\alpha\nu, b=βνb=\beta\nu and a=γνa=\gamma\nu, we have

uz=(a+by2+cy4)(x3)(24)u_z=(a+by^2+cy^4)(x^3) \tag*{(24)}

Further, since section II is assumed to be narrow, the deformation of section I must be such that 2-5 has 0 displacement along the X-axis. In other words, the deformation of 2-5 must occur along a plane parallel to the YZYZ plane and containing 2-5. Note that in the local coordinate, this is a plane containing 2-5 and at an inclination of θ\theta (about xx) from the yzyz plane. This implies that the displacement (uxu_x) along xx at x=lx=l must be

ux∣x=l=uz∣x=ltan⁡θ(25)\left.u_x\right|_{x=l}=\left.u_z\right|_{x=l}\tan\theta \tag*{(25)}

We assume the variation of uxu_x along xx to follow uzu_z and therefore, we have

ux=uz∣x=ltan⁡θ(x3/l3)=uztan⁡θ(26)u_x=\left.u_z\right|_{x=l}\tan\theta\left(x^3/l^3\right)=u_z\tan\theta \tag*{(26)}

Now, assume that a moment MM at 2 (refer Figure S1) causes an inclination of ψ\psi at 2 about the X-axis. Therefore, we have

∂uz/∂y∣(x=l,y=w/2)cos⁡θ=ψ.(27)\frac{\left.\partial u_z/\partial y\right|_{(x=l,y=w/2)}}{\cos\theta}=\psi. \tag*{(27)}

Equation (27) can be used to eliminate a constant (bb) from Eq. (24) to yield

uz=(a+(ψcos⁡θwl3−cw22)y2+cy4)x3(28)u_z=\left(a+\left(\frac{\psi\cos\theta}{wl^3}-\frac{cw^2}{2}\right)y^2+cy^4\right)x^3 \tag*{(28)}

Finally, the displacement (uyu_y) along yy is assumed to be linear along yy and follow a cubic variation similar to uzu_z and uxu_x along xx to give

uy=fyx3,(29)u_y=fyx^3, \tag*{(29)}

where ff is a constant. The strain in the plate is given by

ϵxx=∂ux∂x−z∂2uz∂x2.(30)\epsilon_{xx}=\frac{\partial u_x}{\partial x}-z\frac{\partial^2u_z}{\partial x^2}. \tag*{(30)}
ϵyy=∂uy∂y−z∂2uz∂y2.(31)\epsilon_{yy}=\frac{\partial u_y}{\partial y}-z\frac{\partial^2u_z}{\partial y^2}. \tag*{(31)}
ϵxy=(∂ux∂y+∂uy∂x)/2−z∂2uz∂x∂y.(32)\epsilon_{xy}=\left(\frac{\partial u_x}{\partial y}+\frac{\partial u_y}{\partial x}\right)/2-z\frac{\partial^2u_z}{\partial x\partial y}. \tag*{(32)}

Using Eqs. (26), (28) and (S7) in Eq. (S8), we write the strains in the plate as follows

ϵxx=3x(xtan⁡θ−2z)(ℓ3w(2a−cw2y2+2cy4)+2ψy2cos⁡θ)2ℓ3w(33)\epsilon_{xx}=\frac{3x(x\tan\theta-2z)\left(\ell^{3}w(2a-cw^{2}y^{2}+2cy^{4})+2\psi y^{2}\cos\theta\right)}{2\ell^{3}w} \tag*{(33)}
ϵyy=x3(cz(w2−12y2)+f−2ψzcos⁡θℓ3w)(34)\epsilon_{yy}=x^{3}\left(cz(w^{2}-12y^{2})+f-\frac{2\psi z\cos\theta}{\ell^{3}w}\right) \tag*{(34)}
ϵxy=x2y(ℓ3w(−cxtan⁡θ(w2−4y2)+6cz(w2−4y2)+3f)+2xψsin⁡θ−12ψzcos⁡θ)2ℓ3w(35)\epsilon_{xy}=\frac{x^{2}y\left(\ell^{3}w\left(-cx\tan\theta(w^{2}-4y^{2})+6cz(w^{2}-4y^{2})+3f\right)+2x\psi\sin\theta-12\psi z\cos\theta\right)}{2\ell^{3}w} \tag*{(35)}

Neglecting the effect from the Poisson’s ratio, the corresponding stresses are given by

σxx=Eϵxx.(36)\sigma_{xx}=E\epsilon_{xx}. \tag*{(36)}
σyy=Eϵyy.(37)\sigma_{yy}=E\epsilon_{yy}. \tag*{(37)}
σxy=(E/2)ϵxy.(38)\sigma_{xy}=(E/2)\epsilon_{xy}. \tag*{(38)}

Furthermore, the energy of an infinitesimal element of the section is given by

dU=12(σxxϵxx+σyyϵyy+σxyϵxy)dxdydz.(39)dU=\frac{1}{2}\left(\sigma_{xx}\epsilon_{xx}+\sigma_{yy}\epsilon_{yy}+\sigma_{xy}\epsilon_{xy}\right)dxdydz. \tag*{(39)}

Therefore, using Eq. (S12) and Eqs. (33) to (35) in Eq. (39), we obtain

dU=Ex216ℓ6w2(18(xtan⁡θ−2z)2(ℓ3w(2a−cw2y2+2cy4)+2ψy2cos⁡θ)2+x2y2(ℓ3w(cxtan⁡θ(w2−4y2)−3(2cz(w2−4y2)+f))−2xψsin⁡θ+12ψzcos⁡θ)2+8x4(ℓ3w(cz(w2−12y2)+f)−2ψzcos⁡θ)2)dxdydz.(40)\begin{aligned} dU={}&\frac{Ex^{2}}{16\ell^{6}w^{2}}\Bigl(18(x\tan\theta-2z)^{2}\bigl(\ell^{3}w(2a-cw^{2}y^{2}+2cy^{4})+2\psi y^{2}\cos\theta\bigr)^{2}\\ &+x^{2}y^{2}\bigl(\ell^{3}w(cx\tan\theta(w^{2}-4y^{2})-3(2cz(w^{2}-4y^{2})+f))-2x\psi\sin\theta+12\psi z\cos\theta\bigr)^{2}\\ &+8x^{4}\bigl(\ell^{3}w(cz(w^{2}-12y^{2})+f)-2\psi z\cos\theta\bigr)^{2}\Bigr)dxdydz. \tag*{(40)} \end{aligned}

The total energy (UU) is found by integrating Eq. (40) through the volume as U=∫−ℓw/2ℓw/2∫−w/2w/2∫0ldUU=\int_{-\ell w/2}^{\ell w/2}\int_{-w/2}^{w/2}\int_{0}^{l}dU to give

U=Etw11289600ℓ3w2(3ℓ2w2(tan⁡2θ(1693440a2ℓ6−98784acℓ6w4+160c2ℓ8w6+2247c2ℓ6w8+10584w2ψ2cos⁡(2θ)+10584w4ψ2)−56ℓ3wtan⁡θ(70cfℓ4w3−9ψsin⁡θ(560a−27cw4))+160ℓ8(840f2−c2w6)+20ℓ2sec⁡2θ(8c2ℓ6w6+28cℓ3w3ψcos⁡(3θ)+441f2ℓ4w2cos⁡(2θ)+441f2ℓ4w2+245fℓ2wψsin⁡(3θ)−35ψ2cos⁡(4θ)+35ψ2)−140ℓ4wψsec⁡θ(4cℓw2−35ftan⁡θ))+7t2(403200a2ℓ2w6−23520acℓ6w6+24ℓ3w3ψcos⁡θ(2800a−3cw2(56ℓ2+45w2))+3840c2ℓ10w6+576c2ℓ8w8+535c2ℓ6w10+9600ℓ4ψ2+5040ℓ2w2ψ2+120ψ2cos⁡(2θ)(80ℓ4+42ℓ2w2+21w4)+2520w4ψ2)).(41)\begin{aligned} U={}&\frac{Etw}{11289600\ell^{3}w^{2}}\Bigl(3\ell^{2}w^{2}\bigl(\tan^{2}\theta(1693440a^{2}\ell^{6}-98784ac\ell^{6}w^{4}+160c^{2}\ell^{8}w^{6}+2247c^{2}\ell^{6}w^{8}\\ &\qquad+10584w^{2}\psi^{2}\cos(2\theta)+10584w^{4}\psi^{2})-56\ell^{3}w\tan\theta(70cf\ell^{4}w^{3}-9\psi\sin\theta(560a-27cw^{4}))\\ &\qquad+160\ell^{8}(840f^{2}-c^{2}w^{6})+20\ell^{2}\sec^{2}\theta(8c^{2}\ell^{6}w^{6}+28c\ell^{3}w^{3}\psi\cos(3\theta)+441f^{2}\ell^{4}w^{2}\cos(2\theta)+441f^{2}\ell^{4}w^{2}\\ &\qquad+245f\ell^{2}w\psi\sin(3\theta)-35\psi^{2}\cos(4\theta)+35\psi^{2})-140\ell^{4}w\psi\sec\theta(4c\ell w^{2}-35f\tan\theta))\\ &\qquad+7t^{2}(403200a^{2}\ell^{2}w^{6}-23520ac\ell^{6}w^{6}+24\ell^{3}w^{3}\psi\cos\theta(2800a-3cw^{2}(56\ell^{2}+45w^{2}))\\ &\qquad+3840c^{2}\ell^{10}w^{6}+576c^{2}\ell^{8}w^{8}+535c^{2}\ell^{6}w^{10}+9600\ell^{4}\psi^{2}+5040\ell^{2}w^{2}\psi^{2}\\ &\qquad+120\psi^{2}\cos(2\theta)(80\ell^{4}+42\ell^{2}w^{2}+21w^{4})+2520w^{4}\psi^{2})\Bigr). \tag*{(41)} \end{aligned}

Finally, the constants aa, cc, ff, and ψ\psi are obtained through energy minimization with respect to these constants. In other words, the following set of equations is solved simultaneously

∂U∂a=0(42)\frac{\partial U}{\partial a}=0 \tag*{(42)}
∂U∂c=0(43)\frac{\partial U}{\partial c}=0 \tag*{(43)}
∂U∂f=0(44)\frac{\partial U}{\partial f}=0 \tag*{(44)}
∂U∂ψ=M(45)\frac{\partial U}{\partial\psi}=M \tag*{(45)}

Using Eq. (41) in Eq. (S16) and solving simultaneously using the symbolic computing toolbox in MATHEMATICA® yields

\begin{aligned} a={}&\frac{525Mw^{2}\sec\theta\left(3l^{2}w^{2}\tan^{2}\theta\left(28800l^{4}+48965l^{2}w^{2}+7056w^{4}\right)\right.\\ &\left.-28\left(160l^{2}+21w^{2}\right)\left(2400l^{4}-81l^{2}w^{2}-20w^{4}\right)t_{w}^{2}\right)}{G} \tag*{(46)} \end{aligned}
c=882000Msec⁡θ(4(63l2+20w2)(160l2+21w2)tw2+l2tan⁡2θ(9600l4+23075l2w2+3024w4))G(47)c=\frac{882000M\sec\theta\left(4\left(63l^{2}+20w^{2}\right)\left(160l^{2}+21w^{2}\right)t_{w}^{2}+l^{2}\tan^{2}\theta\left(9600l^{4}+23075l^{2}w^{2}+3024w^{4}\right)\right)}{G} \tag*{(47)}
f=1176000Mw2tan⁡θsec⁡θ(−7(600l5+27l3w2+10lw4)tw2−9l3w2tan⁡2θ(5l2+14w2))G(48)f=\frac{1176000Mw^{2}\tan\theta\sec\theta\left(-7\left(600l^{5}+27l^{3}w^{2}+10lw^{4}\right)t_{w}^{2}-9l^{3}w^{2}\tan^{2}\theta\left(5l^{2}+14w^{2}\right)\right)}{G} \tag*{(48)}
ψ=25200l3Msec⁡2θ(840w(160l2+21w2)(20l4+3l2w2+w4)tw2+l2w3tan⁡2θ(96000l4+245945l2w2+31752w4))G(49)\psi=\frac{25200l^{3}M\sec^{2}\theta\left(840w\left(160l^{2}+21w^{2}\right)\left(20l^{4}+3l^{2}w^{2}+w^{4}\right)t_{w}^{2}+l^{2}w^{3}\tan^{2}\theta\left(96000l^{4}+245945l^{2}w^{2}+31752w^{4}\right)\right)}{G} \tag*{(49)}

where GG is given as

G=Etw(9l4w4tan⁡4θ(240000l6+672875l4w2+215180l2w4+21168w6)+5l2w2tan⁡2θ(51840000l8+101026800l6w2+18697875l4w4+1043252l2w6+42336w8)+140(160l2+21w2)(72000l8+48600l6w2+13701l4w4+630l2w6+20w8)tw4).\begin{aligned} G=Et_{w}\big(&9l^{4}w^{4}\tan^{4}\theta\left(240000l^{6}+672875l^{4}w^{2}+215180l^{2}w^{4}+21168w^{6}\right)\\ &+5l^{2}w^{2}\tan^{2}\theta\left(51840000l^{8}+101026800l^{6}w^{2}+18697875l^{4}w^{4}+1043252l^{2}w^{6}+42336w^{8}\right)\\ &+140\left(160l^{2}+21w^{2}\right)\left(72000l^{8}+48600l^{6}w^{2}+13701l^{4}w^{4}+630l^{2}w^{6}+20w^{8}\right)t_{w}^{4}\big). \end{aligned}

It is evident from Eq. (S17d) that ψ\psi is linear with respect to M (Note that small strain assumptions have been made). Consequently, the stiffness of section I (and III equivalently) can thus be found as τI=M/ψ\tau_{I}=M/\psi, which yields

τI=G25200l3sec⁡2θ(840w(160l2+21w2)(20l4+3l2w2+w4)tw2+l2w3tan⁡2θ(96000l4+245945l2w2+31752w4)).(50)\tau_{I}=\frac{G}{25200l^{3}\sec^{2}\theta\left(840w\left(160l^{2}+21w^{2}\right)\left(20l^{4}+3l^{2}w^{2}+w^{4}\right)t_{w}^{2}+l^{2}w^{3}\tan^{2}\theta\left(96000l^{4}+245945l^{2}w^{2}+31752w^{4}\right)\right)}. \tag*{(50)}

Therefore, using Eq. (50), the total stiffness of the equivalent torsion spring can thus be written as

τ=τII+2G25200l3sec⁡2θ(840w(160l2+21w2)(20l4+3l2w2+w4)tw2+l2w3tan⁡2θ(96000l4+245945l2w2+31752w4)).(51)\tau=\tau_{II}+\frac{2G}{25200l^{3}\sec^{2}\theta\left(840w\left(160l^{2}+21w^{2}\right)\left(20l^{4}+3l^{2}w^{2}+w^{4}\right)t_{w}^{2}+l^{2}w^{3}\tan^{2}\theta\left(96000l^{4}+245945l^{2}w^{2}+31752w^{4}\right)\right)}. \tag*{(51)}

where τII\tau_{II} is given by

τII=E(d3tan⁡2θsec⁡θtw+4dcos⁡θtw3)24w,(52)\tau_{II}=\frac{E\left(d^{3}\tan^{2}\theta\sec\theta t_{w}+4d\cos\theta t_{w}^{3}\right)}{24w}, \tag*{(52)}

where dd is the width of the bridge film. The above expression is found by evaluating the area moment of inertia of II as twice that of a rectangular section rotated through θ\theta.

The stiffness of the equivalent torsion spring can thus be approximated by Eq. (51). It is to be noted that the above expression has been derived assuming a certain polynomial form for the displacements. Consequently, it is found that the Eq. (51) holds only within a certain domain. Accordingly, the above expression is found to be valid for (10≤l/tw≤60)(10 \le l/t_{w} \le60). A large class of hexagonal cellular structures fall within this domain, and the above formula can be used to approximate their stiffness. On the other hand, higher accuracies and larger domains of validity require higher-order approximations.

References

  1. [1]L. J. Gibson, M. F. Ashby, Cellular solids: Structure and properties, 2nd ed., Cambridge University Press, 1997.

Paper details

vlnc:W_bzccxrtv
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents