betaFeedback

WorksPhysics and Astronomy

Field-free deterministic spin-orbit torque magnetization switching using monolayer WTe2

Abstract

An important step towards the practical implementation of spin-orbit torque magnetic memory is the field-free switching of the magnetization vector. In this work, we investigate spin-orbit torque-driven magnetization dynamics and switching devices comprising monolayer WTe2\mathrm{WTe}_2 as the spin-source material. We perform a comparative analysis of the two phases of WTe2\mathrm{WTe}_2, namely the 1Td1\mathrm{T}_d and 1T′1\mathrm{T}' with the necessary symmetries for field-free deterministic magnetization switching. We demonstrate switching in both systems and analyse the dependence of the switching dynamics on the applied bias voltage, ribbon orientation and width of the magnetic layer. Modelling the ferromagnet as an exchange-coupled macrospin within a non-equilibrium Green's function framework, we find that the xx-ribbon geometry of the 1Td1\mathrm{T}_d WTe2\mathrm{WTe}_2 phase generates a significantly larger current-induced spin polarization than the 1T′1\mathrm{T}' phase, resulting in a larger damping-like torque on the adjacent magnetic layer and faster switching. The switching time of 1T′1\mathrm{T}' devices varies strongly and non-monotonically with the width of the magnetic layer. In 1Td1\mathrm{T}_d devices, it remains nearly constant over a broad range of widths, consistent with an edge-dominated torque. These results identify xx-ribbon 1Td1\mathrm{T}_d-WTe2\mathrm{WTe}_2 as a promising spin source for field-free SOT-MRAM.

Introduction

Spintronic memory technologies offer nonvolatile data storage, high endurance, and fast operation, making them attractive alternatives to conventional charge-based memories [1, 2, 3, 4, 5]. Among these, magnetic random-access memory (MRAM) is particularly promising because information is stored in the magnetization state of the free layer of a magnetic tunnel junction (MTJ), enabling nonvolatile operation and compatibility with CMOS technologies [2, 3, 4, 5]. Within the MRAM family, spin-transfer-torque MRAM (STT-MRAM) switches the magnetization of the free layer by driving a spin-polarised current through the MTJ [6, 7, 8]. However, as the read and write operations share the same current path, the high current densities flowing through the tunnel barrier lead to reduced endurance [9]. In contrast, spin-orbit torque MRAM (SOT-MRAM) uses an in-plane charge current injected through an adjacent spin-source layer, where spin-orbit coupling (SOC) converts it into a spin density that exerts a torque on the adjacent free ferromagnetic (FM) layer without passing through the tunnel barrier, thereby decoupling the read and write paths. This architecture reduces stress on the tunnel barrier during write operations and enables higher endurance and faster switching, making SOT-MRAM an attractive platform for high-performance magnetic memory [4, 5, 9, 10, 11, 12].

A central challenge in SOT-MRAM is achieving deterministic switching without an external magnetic field. Spin-orbit torques can be decomposed into two components: a field-like torque which is analogous to an effective magnetic field, and a damping-like torque which acts like an effective magnetic damping [3]. In conventional heavy-metal/ferromagnet bilayer systems, the spin current generated via the spin Hall effect [13] is polarised along the in-plane transverse direction, producing a damping-like torque that is symmetric with respect to both the perpendicular magnetization states; breaking this degeneracy typically requires an auxiliary in-plane magnetic field for switching of an out of plane magnet [3, 11, 15]. While several strategies have been explored to achieve field-free switching, such as interlayer exchange coupling [16], interlayer Dzyaloshinskii–Moriya interaction [17], and vertical composition gradients in the magnetic layer [18], these approaches introduce additional material or structural complexity. A more intrinsic route is to exploit crystal symmetry, as a spin-source layer with broken inversion and appropriate mirror symmetries can generate an out-of-plane canted spin polarization, producing a torque on the FM layer that lifts the degeneracy between the two magnetization states without an external magnetic field [15, 19, 20, 21, 22, 23, 24].

The monolayer WTe2_2 is a 2D-transition-metal dichalcogenide (TMD) that is particularly well-suited to satisfy the symmetry requirements outlined above. Unlike conventional 2H or 1T TMDs [25], monolayer WTe2_2 is the most stable in the 1T′ phase [26, 27]. The 1Td_d phase differs from the 1T′ by breaking the inversion symmetry, as shown in Figure 1(a,Figure 1b) [28]. Both phases of monolayer WTe2_2 are theoretically expected to be quantum spin Hall insulators with edge states exhibiting canted outof-plane spin-polarization [28, 29], enabling out-of-plane damping-like torques on the FM layer [21]. While 1T′' has been studied quite extensively experimentally [30, 31, 32, 33, 34], the monolayer of 1Td_d phase has been recently synthesised [35]. The unconventional out-of-plane spin-orbit torque in multilayer WTe2_2 / FM bilayers was first experimentally demonstrated by MacNeill et al. [21], illustrating the utility of WTe2_2 for crystal-symmetry engineered SOT. Subsequent experiments have demonstrated field-free deterministic magnetization switching in a range of WTe2_2-based heterostructures, including systems employing unconventional spin-orbit and orbital torques [36, 37, 38, 39, 40, 41]. However, these works primarily focus on multilayer or few-layer devices. A direct phase comparison of 1Td_d and 1T′' phases of monolayer WTe2_2, to the best of our knowledge has not been reported, motivating the present theoretical study.

Schematic of the WTe$_2$ lattice structure, device layout, and material symmetries

Figure 1. Schematic of the WTe2_2 lattice structure in the 1T′' and 1Td_d phases, along with the device layout and material symmetries. (a,b) Unit cells of WTe2_2 in the 1T′' and 1Td_d phases, respectively. The lower panels show side views of the lattices, where the structural distortion characteristic of the 1Td_d phase is evident in (b). (c) Mirror symmetry constraint for deterministic field-free SOT switching. Magnetization vector m⃗\vec{m} is the stable magnetization state for current II. Any mirror symmetry parallel to the current flow allows for an equivalent state of opposite magnetization to be stable at the same direction of current flow. This creates two equivalently stable states, which leads to non-deterministic switching, necessitating breaking of mirror symmetries parallel to the current flow. (d) Schematic of the two-terminal device. The channel consists of monolayer WTe2_2, which is being injected with current JinJ_{\mathrm{in}}. A ferromagnet (FM, coloured green) with width WW is placed on top of the WTe2_2 layer. It is described via a macrospin approximation with magnetization m⃗(t)\vec{m}(t), which is precessing due to the spin-orbit torque applied by the spin density created in WTe2_2.

In this work, we simulate the SOT generation and magnetization dynamics of the FM for both 1Td_d and 1T′' phases of WTe2_2 and perform a comparative study between the two phases. We find that both phases apply SOT on the FM layer and show deterministic field-free switching. By further analysing the dependence of the switching time on the applied bias voltage and width of the magnetic layer, we conclude that the 1Td_d phase

in the x-ribbon geometry is better suited for this application, owing to the larger SOT it exerts on the FM layer, its shorter switching times and weaker sensitivity to the magnet width. The paper is organised as follows: Section II presents the theoretical framework underlying the symmetry constraints and the Non-Equilibrium Green’s Function (NEGF) formalism combined with the Landau-Lifshitz-Gilbert (LLG) equation to compute the spin-orbit torque on the FM layer and the resulting magnetization dynamics, Section III presents the results and compares the performance between the two phases, Section IV concludes the results and summarises future work that can be done for a more realistic simulation of a SOT device.

Theory

In this section, we outline the theoretical framework used to compute SOT and the resulting magnetization dynamics in monolayer WTe2_2-based devices. Our approach combines a symmetry-consistent tight-binding description of the electronic structure with the NEGF formalism [42] to evaluate SOT. The time evolution of the adjacent FM layer under the influence of the SOT is then obtained by solving LLG equation. We first discuss the symmetry requirements necessary for deterministic, field-free switching, followed by a description of the material Hamiltonians and transport formalism, and finally outline the procedure used to compute the magnetization dynamics[43, 44].

Symmetry requirements

The generation of SOT and the realisation of deterministic, field-free magnetization switching are constrained by the inversion and mirror symmetries of the device as follows [19]:

  1. Inversion symmetry: Broken inversion symmetry is a necessary condition for obtaining a non-vanishing SOT. In the absence of inversion symmetry, an applied electric field can generate a non-equilibrium spin density via the Rashba-Edelstein effect, which acts as the microscopic source of SOT. If inversion symmetry is preserved, these contributions cancel, resulting in a vanishing net torque.

  1. Mirror symmetry: magnetization is an axial vector, and mirror symmetries impose additional constraints on current-induced switching. If a mirror plane parallel to the current direction is preserved, the system admits two symmetry-related magnetization configurations that are equivalent for a given current direction as shown in Figure 1c, leading to non-deterministic switching. Deterministic field-free switching therefore requires that the mirror symmetry parallel to the current flow be broken, while a mirror symmetry perpendicular to the current direction may be preserved.

These symmetry considerations make monolayer WTe2_2 a particularly suitable platform for realising deterministic, field-free SOT switching. As outlined in Figure 1a, in the 1T′ phase, the crystal structure preserves a glide mirror symmetry (MxM_x) and a screw rotation symmetry (C2xC_{2x}), which together give rise to inversion symmetry [45]. In contrast, the distorted 1Td_d phase breaks C2xC_{2x} symmetry, which leads to inversion symmetry breaking. Hence 1Td_d automatically satisfies the necessary conditions stated above [28]. While 1T′ does not, one can break the local inversion symmetry by placing an adjacent FM layer, enabling field-free SOT generation. In both phases, appropriate device geometries can be chosen to break the mirror symmetry parallel to the current direction (or it is already broken for x-ribbon geometries), thereby allowing deterministic switching without the need for an external magnetic field.

Material Hamiltonian and device model

Both the phases of monolayer WTe2_2 are quantum spin Hall insulators, exhibiting canted spin polarization along

with strong SOC. To capture these properties, we employ symmetry-consistent tight-binding Hamiltonians derived in previous works for each phase. For the 1Td_d phase, we use a model given by JH Garcia et al, which was constructed from symmetry-allowed terms and fitted to DFT calculations [28], while for the 1T′ phase we adopt a tight-binding description obtained from a combination of DFT, symmetry analysis, and ARPES data derived by A Lau et al [29]. The Hamiltonian and self-energies for the 1T′ phase were calculated using the quantum transport software package Kwant [46]. These Hamiltonians provide an accurate description of the low-energy band structure relevant for our work. However, we need to note that these Hamiltonians are only valid for small biases.

The device geometry considered throughout this work is shown in Figure 1d. It consists of a finite WTe2_2 scattering region connected to semi-infinite left and right leads and subjected to a bias voltage, and a FM layer on top which is approximated as a macrospin m~\tilde{\mathbf m}. The FM layer is exchange-coupled to selected lattice sites of the WTe2_2 channel via a surface exchange interaction,

U(t)=−Δsurf2m~(t)⋅σ,(1)U(t)=-\frac{\Delta_{\mathrm{surf}}}{2}\tilde{\mathbf m}(t)\cdot\boldsymbol{\sigma}, \tag*{(1)}

where Δsurf\Delta_{\mathrm{surf}} denotes the exchange strength, m~(t)\tilde{\mathbf m}(t) is the time-dependent unit magnetization vector of the FM, and σ\boldsymbol{\sigma} is the vector of Pauli matrices. The total Hamiltonian of the device is then given by H(t)=H0+U(t)H(t)=H_0+U(t), where H0H_0 is the tight-binding Hamiltonian of the isolated WTe2_2 monolayer. This coupling locally breaks inversion symmetry in the 1T′ phase enabling current-induced SOTs in devices of both phases. We infer the relative edge and bulk contributions to the torque from the dependence of the switching time on magnet with (III C).

Transport formalism and magnetization dynamics

The SOTs acting on the magnetic layer are computed using the NEGF formalism applied to the time-dependent device Hamiltonian H(t)H(t) [43, 44]. For a given magnetization configuration m~(t)\tilde{\mathbf m}(t), the retarded Green’s function of the scattering region is given by[42]

G(E,t)=[E−H(t)−ΣL(E)−ΣR(E)]−1,(2)G(E,t)=\left[E-H(t)-\Sigma_L(E)-\Sigma_R(E)\right]^{-1}, \tag*{(2)}

where ΣL,R\Sigma_{L,R} denote the self-energies of the left and right leads. The applied bias voltage enters through the difference in the electrochemical potentials of the leads. Throughout this work, the FM layer is treated as an exchange-coupled perturbation and not as an additional transport channel, hence no current is allowed to flow through the FM.

The bias-induced nonequilibrium spin density is obtained from the lesser Green’s function and serves as the microscopic origin of the SOT. The resulting torque acting on the magnetization is evaluated following established NEGF-based formulations and can be decomposed

into symmetry-distinct components, including field-like and damping-like contributions. In equilibrium, the torque component is found to be aligned with the intrinsic spin-polarization axis of edge states in WTe2_2, and hence can be absorbed into the anisotropy torque T⃗MCA\vec{T}_{\mathrm{MCA}} [43, 44]. The energy resolved torque components are τ⃗μ,ν(E)\vec{\tau}_{\mu,\nu}(E), where μ,ν\mu,\nu denote whether the torque component is odd (oo) or even (ee) under bias-reversal and time-reversal respectively.

The time evolution of the magnetization is obtained by solving the LLG equation,

dm⃗dt=α(m⃗×dm⃗dt)+T⃗MCA+γμT⃗SOT−γ(m⃗×B⃗)(3)\frac{d\vec{m}}{dt}=\alpha\left(\vec{m}\times\frac{d\vec{m}}{dt}\right)+\vec{T}_{\mathrm{MCA}}+\frac{\gamma}{\mu}\vec{T}_{\mathrm{SOT}}-\gamma(\vec{m}\times\vec{B}) \tag*{(3)}

where γ\gamma is the gyromagnetic ratio, μ\mu is the magnetic moment, B⃗\vec{B} is the external magnetic field, T⃗MCA=ΔMCA(m⃗⋅σ⃗P)(m⃗×σ⃗P)\vec{T}_{\mathrm{MCA}}=\Delta_{\mathrm{MCA}}(\vec{m}\cdot\vec{\sigma}_{P})(\vec{m}\times\vec{\sigma}_{P}) is the magnetic anisotropy aligned with the spin polarization vector σ⃗P\vec{\sigma}_{P}, α\alpha is the Gilbert damping parameter and T⃗SOT\vec{T}_{\mathrm{SOT}} is the SOT produced. We can simplify this equation by defining dimensionless time teff=tΔMCAt_{\mathrm{eff}}=t\Delta_{\mathrm{MCA}} and bias voltage Veff=γeVb/(μΔMCA)V_{\mathrm{eff}}=\gamma eV_b/(\mu\Delta_{\mathrm{MCA}}), which will be used to perform simulations for the results.

The magnetization dynamics are simulated self-consistently by iterating between the SOT calculation and the LLG equation. Starting from an initial magnetization configuration, the torque is evaluated for the corresponding H(t)H(t), the magnetization is updated over a small time step, and the procedure is repeated until the magnetization converges to a steady state or switching is achieved. This approach allows to incorporate time-dependence of the SOT, giving a more accurate description of the dynamics involved. The full details of the theory are laid out in Appendix A, and the physical constants used are give in IIIB.

Results and Discussion

In this section, we present numerical results for SOT generation and magnetization dynamics in monolayer WTe2_2-based SOT devices at zero magnetic field, focusing on the contrasting behaviour of the 1T′' and 1Td_d phases. Using NEGF-based torque calculations combined with Landau–Lifshitz–Gilbert dynamics, we first demonstrate deterministic, field-free magnetization switching in both systems and compare the magnitude and angular dependence of the torque components. All the results have been calculated by using dimensionless time and bias voltage, with Δsurf=0.1\Delta_{\mathrm{surf}}=0.1 eV and α=0.01\alpha=0.01. We then analyse the dependence of the switching time on the applied bias voltage and ribbon orientation, identifying clear performance trends and voltage thresholds across different device geometries. Finally, we investigate the role of magnetic layer width and show that switching time in 1Td_d devices remains constant to variations in magnet width. It increases only when the magnet covers both the edges of the WTe2_2 layer, where the torque from the opposite edge partly cancels that from the first. The 1T′' devices exhibit strong and non-monotonic sensitivity to variations in the magnet width due to enhanced bulk contributions. Together, these results establish 1Td_d-WTe2_2 x-ribbon geometries as the most favourable platform for fast and reliable field-free SOT switching.

Magnetization Switching

We first examine the angular dependence and magnitude of the spin-orbit torque acting on the magnetic layer in the WTe2_2 devices for the 1Td_d and 1T′' phases. Figure 2 shows the energy-resolved torque components as a function of the polar angle θ\theta of the magnetization for x-ribbon geometries, with the azimuthal angle fixed at ϕ=π/2\phi=\pi/2. All torque components exhibit a strong dependence on the magnetization direction, reflecting the underlying spin texture of WTe2_2. Over most of the angular range, the 1Td_d x-ribbon produces a larger torque magnitude on the magnetic layer than its 1T′' counterpart, particularly for the damping-like component τoe\tau_{oe}, which is expected to be primarily responsible for driving magnetization reversal. This enhancement is consistent with the intrinsically broken inversion symmetry of the 1Td_d phase, whereas in the 1T′' phase inversion symmetry is broken only through the presence of the FM layer.

Figure 2. Magnitude of the torque components as a function of the polar angle θ\theta, with the azimuthal angle fixed at ϕ=π2\phi= \frac{\pi}{2} for WTe2_2 1Td_d and 1T′x_x-ribbon geometries. The scattering region of 16×1616 \times16 unit cells, and the magnetic layer is placed on the top edge only. The three panels correspond to (a) ∣τoo∣|\tau_{oo}|, (b) ∣τee∣|\tau_{ee}|, and (c) ∣τoe∣|\tau_{oe}|, where τee\tau_{ee} and τoo\tau_{oo} represent the equilibrium and non-equilibrium field-like components, respectively, and τoe\tau_{oe} denotes the damping-like component of the SOT. The τeo\tau_{eo} can be shown to vanish identically [47], and hence not shown here. Over the majority of the angular range, the (1Td)x/FM(1T_d)_x/\mathrm{FM} device exhibits a larger torque magnitude on the FM layer compared to the (1T′)x/FM(1T')_x/\mathrm{FM} for all components.

The resulting magnetization dynamics, obtained by solving the Landau–Lifshitz–Gilbert equation using the self-consistently calculated torques, are shown in Figure 3. For both phases, an initial magnetization slightly canted away from the spin-polarization direction undergoes deterministic, field-free switching to the opposite stable orientation upon application of a bias voltage. The stable orientation is different for the two phases: σ⃗P,(1Td)=(0,−cos⁡(54.5∘),sin⁡(54.5∘))\vec{\sigma}_{P,(1T_d)}=(0,-\cos(54.5^\circ),\sin(54.5^\circ)) for 1Td_d and σ⃗P,(1T′)=(0,−cos⁡(14.5∘),−sin⁡(14.5∘))\vec{\sigma}_{P,(1T') }=(0,-\cos(14.5^\circ),-\sin(14.5^\circ)) for 1T′'. Consistent with the larger torque magnitudes, the switching time in the 1Td_d x-ribbon is significantly shorter than in the 1T′' x-ribbon for comparable device parameters, making it a better candidate for potential SOT applications.

Magnetization dynamics and Bloch-sphere trajectories for two WTe2 geometries

Figure 3. Magnetization dynamics using a monolayer WTe2_2 1Td_d and 1T′x_x-ribbon geometries, with the scattering region of size 16×1616 \times16 unit cells. A bias of Veff=10V_{\mathrm{eff}} = 10 is applied to both the devices. The magnet is kept on only the topmost row of unit cells (a) The spin polarization vector for 1Td_d x-ribbon is (0,−cos⁡(54.5∘),sin⁡(54.5∘))(0, -\cos(54.5^\circ), \sin(54.5^\circ)). The initial condition is slightly canted away from −σ⃗P-\vec{\sigma}_P, showing clean switching to σ⃗P\vec{\sigma}_P. (b) The spin polarization vector for 1T′x_x-ribbon is (0,−cos⁡(14.5∘),−sin⁡(14.5∘))(0, -\cos(14.5^\circ), -\sin(14.5^\circ)). Here also the initial condition is slightly canted from −σ⃗P-\vec{\sigma}_P and shows switching to σ⃗P\vec{\sigma}_P. For both (a) and (b) the trajectory of the magnetization is shown on a Bloch sphere in the bottom panels.

Voltage and ribbon-geometry dependence

We next examine how the magnetization switching time depends on the applied bias voltage and ribbon orientation for monolayer WTe2_2 devices in the 1Td_d and 1T′' phases. Figure 4 shows the switching time as a function of bias voltage for both x- and y-ribbon geometries. In all cases, increasing the applied voltage leads to faster switching, reflecting the monotonic increase in the magnitude of the non-equilibrium spin-orbit torque with bias. However, the improvement in switching time exhibits diminishing returns at higher voltages. Note that our analysis uses the small-bias approximation, and hence cannot accurately predict the behaviour at large bias voltage.

Switching time as a function of bias voltage for x- and y-ribbons of WTe2 in the 1T′ and 1Td phases

Figure 4. Switching time as a function of bias voltage for (a) x-ribbons with scattering region of size 16 × 16 unit cells and (b) y-ribbons of WTe2 in the 1T′ and 1Td phases with 12 × 12 unit cells. The magnet is placed only on the top row of unit cells for all devices. Among all cases, the (1Td)x ribbon exhibits the fastest switching, followed by (1T′)x, (1T′)y, and (1Td)y. Notably, both y-ribbons require significantly higher minimum bias voltages (nearly two orders of magnitude larger) for switching compared to the x-ribbons.

A clear distinction in device performance emerges from the comparison across phases and geometries. Among all configurations studied, the 1Td x-ribbon exhibits the fastest switching, followed by the 1T′ x-ribbon, while both y-ribbon geometries require substantially higher bias voltages to achieve switching. In particular, the minimum voltage required for switching in y-ribbons is nearly two orders of magnitude larger than that for x-ribbons in both phases. However, as the device sizes are different, this is a qualitative comparison. The switching time at Veff=10V_{\mathrm{eff}} = 10 in the x-ribbon orientation for 1Td is teff=1.55t_{\mathrm{eff}} = 1.55, while for 1T′ teff=26.29t_{\mathrm{eff}} = 26.29, which is approximately 17 times that of 1Td. For γ=1.76×1011 s−1T−1\gamma= 1.76 \times10^{11}\ \mathrm{s}^{-1}\mathrm{T}^{-1} magnetic moment μ=O(μB)∼9.274×10−24 J T−1\mu= O(\mu_B) \sim9.274 \times10^{-24}\ \mathrm{J}\,\mathrm{T}^{-1}, e=1.6×10−19Ce = 1.6 \times10^{-19}\mathrm{C} and ΔMCA=O(γHK)∼1011 s−1\Delta M_{\mathrm{CA}} = O(\gamma H_K) \sim10^{11}\ \mathrm{s}^{-1} (an anisotropy field HK≈0.6 TH_K \approx0.6\ \mathrm{T}), we get a value of t∼15.5 pst \sim15.5\ \mathrm{ps} for 1Td at Vb=0.33 mVV_b = 0.33\ \mathrm{mV}. These estimates are order-of-magnitude only due to the qualitative nature of this study and lie within the small-bias regime. The better performance of the 1Td x-ribbon can be traced to its larger damping-like torque over a broad range of magnetization angles because it satisfies all the symmetry requirements intrinsically, whereas in 1T′ the inversion symmetry is broken only on addition of the magnet on top. Hence we can conclude that x-oriented 1Td-WTe2 devices are more favourable for field-free switching.

Magnetic layer size dependence

We finally investigate the dependence of the switching dynamics on the width of the magnetic layer, which is an important consideration for realistic device fabrication. In all previous simulations, the magnetic layer was restricted to a single unit cell in width and extended along the full length of the channel, thereby breaking the inversion symmetry along with the mirror plane parallel to the current flow. To assess the robustness of the switching behaviour, we systematically vary the magnet width while keeping its length fixed and compute the corresponding switching times, as shown in Figure 5. For the 1Td x-ribbon, the switching time decreases slightly as the magnet width increases from one to two unit cells and then remains nearly constant over a broad range of widths before increasing sharply for very wide magnets. This behaviour indicates that the dominant contribution to the spin-orbit torque arises from edge states, with negligible bulk contribution over most of the device width. At the other edge, the switching time shoots up, indicating incomplete cancellation of SOT from the other edge. However, the SOT does not vanish due to inversion symmetry breaking making the two edges.

Switching time as a function of magnet width for WTe2 in the $(1T_d)_x$ and $(1T')_x$ phases

Figure 5. Switching time as a function of magnet width for WTe2_2 in (a) the (1Td)x(1T_d)_x phase and (b) the (1T′)x(1T')_x phase devices with scattering region of 16 ×\times 16 unit cells at Veff=100V_{\mathrm{eff}} = 100. The magnet width is varied while the length is kept constant spanning the entire channel. For (1Td)x(1T_d)_x, the switching time remains nearly unchanged with increasing width, indicating that the torque originates primarily from the edges with negligible bulk contribution. It is therefore not advisable to place the magnet over the entire device, since the spin polarization at the two edges is opposite; the torque arising from the bottom edge opposes that from the top edge (though with unequal magnitude), resulting in longer switching times. In contrast, for (1T′)x(1T')_x, the switching time varies non-monotonically with width, reflecting enhanced torque generation due to bulk contributions. Notably, no switching occurs in the 1T′1T' phase for magnets two and three unit cells wide.

In contrast, the 1T′ x-ribbon exhibits a markedly different and non-monotonic dependence on magnet width. Switching occurs for a one unit cell wide magnet, but not for 2 and 3 unit cells. Beyond that, the switching time varies irregularly with width, decreasing overall towards the full channel width. This behaviour suggests a substantial contribution from bulk states, possibly due to a smaller band gap. The pronounced sensitivity of 1T′ devices to magnet size makes them less robust compared to the 1Td devices.

Conclusion and Outlook

Topological insulators are attractive platforms for nanoscale devices due to their robustness against disorder. and noise. Previous studies have explored their potential in magnetic memory applications, including proposals based on the Kane–Mele model [43] and experimentally realized topological insulators [44]. However, these works suffer from key limitations: the Kane–Mele model possesses an unrealistically small band gap, making experimental realisation challenging, while other material platforms, despite being experimentally accessible, fail to satisfy the symmetry requirements necessary for field-free deterministic magnetization switching. In this work, we overcome both limitations by identifying a material system that is experimentally realizable and simultaneously satisfies the required symmetry constraints. Furthermore, we provide a more comprehensive analysis of the conditions necessary to achieve reliable magnetization switching.

We performed a comparative study of current-induced magnetization switching in the 1Td1T_d and 1T′1T' phases of WTe2_2. Using symmetry arguments, we demonstrated that deterministic switching can be achieved in the absence of external magnetic fields. The superior switching performance of the 1Td1T_d phase in the x-ribbon geometry correlated with the larger damping-like torque it exerts on the FM layer over a broad range of magnetisation angles, which we attribute to its intrinsically broken inversion symmetry. We found that, in both phases, the x-ribbon geometry requires a significantly lower minimum voltage to initiate switching. Additionally, independent of the material phase or device geometry, the improvement in switching time saturates with increasing applied voltage.

We also observed that the switching time in the 1Td1T_d phase exhibits weaker sensitivity to variations in magnet width, owing to the dominant contribution of edge-induced torque. In contrast, for the 1T′1T' phase, comparable edge and bulk torque contributions result in a stronger dependence of the switching dynamics on magnet width.

Our results rely on several simplifications that future work should relax. The FM is modelled as an insulating macrospin coupled only through exchange, neglecting any current passing through it. Since the edge-dominated torque depends on a clean bulk gap, edge disorder, thermal broadening and larger device sizes should be examined before the width robustness of 1Td1T_d devices can be generalized. The influence of strain [48] on the switching efficiency and overall device performance in WTe2_2 is another open question. Additionally, the use of counter-propagating spin currents in quantum spin Hall insulators offers an intriguing avenue for extending these concepts to the deterministic switching of antiferromagnetic systems.

Acknowledgments

We thank Dr. Venkatesh Vadde for his valuable insights and helpful discussions, particularly during the initial setup of the simulation framework used in this work. The author BM acknowledges funding from the Department of Science and Technology (DST), Government of India, under the National Quantum Mission, through Grant no. DST/QTC/NQM/QMD/2024/4, the Institute of Eminence Grant from IIT Bombay, through Grant no. RD/0523-IOE00I0-139 and the Inani Chair Professorship fund, through Grant No. DO/2024-INAN/001-001. SPD acknowledges funding from Swedish Research Council VR (No. 2025-03702). The authors BM and ST acknowledge funding from the Dhananjay Joshi Endowment award from IIT Bombay, through Grant No: DO/2023-DJEF002.

Data availability The data that support the findings of this study are available from the corresponding author upon reasonable request.

Methodology

In this appendix, we provide a detailed description of the theoretical framework used in our simulations. The formalism employed to compute spin–orbit torques (SOTs) follows [44]. The device Hamiltonian is time dependent due to the dynamics of the magnetic moments in the ferromagnetic (FM) layer and is written as

H^(t)=H^0+U^0(t),(4)\hat{H}(t) = \hat{H}_0 + \hat{U}_0(t), \tag*{(4)}

where H^0\hat{H}_0 denotes the static part of the Hamiltonian and U^0(t)\hat{U}_0(t) describes the exchange coupling between the device and the magnetic layer. Explicitly,

U^0(t)=−c^i′†(Δsurf2m⃗i′(t)⋅σ⃗)c^i′,(5)\hat{U}_0(t) = -\hat{c}_{i'}^\dagger\left( \frac{\Delta_{\mathrm{surf}}}{2} \vec{m}_{i'}(t) \cdot\vec{\sigma} \right) \hat{c}_{i'}, \tag*{(5)}

where Δsurf\Delta_{\mathrm{surf}} is the interfacial exchange coupling strength, m⃗i′(t)\vec{m}_{i'}(t) is the unit magnetization vector at lattice site i′i', and σ^\hat{\sigma} denotes the Pauli matrices. Assuming an adiabatic approximation, valid when the magnetization dynamics is slow compared to electronic time scales, the spin density at the device-magnet interface can be expressed as

si(t)≈∫dE2π[∑αfα(E)Tiα(E)−Δsurf2∑jf′(E)∂mj∂tTij(E)],(6)s^i(t) \approx\int\frac{dE}{2\pi} \left[ \sum_{\alpha} f_{\alpha}(E) T^{i\alpha}(E) - \frac{\Delta_{\mathrm{surf}}}{2} \sum_j f'(E) \frac{\partial m_j}{\partial t} T^{ij}(E) \right], \tag*{(6)}

where fα(E)f_{\alpha}(E) is the Fermi–Dirac distribution function of lead α\alpha, f′(E)f'(E) is its energy derivative, α∈{L,R}\alpha\in\{L, R\}, and i,j∈{x,y,z}i,j \in\{x,y,z\} label spin components. The energy-resolved transmission coefficients are given by the trace formulas

Tαβ(E)=Tr⁡[ΓαGtΓβGt†],(7)T^{\alpha\beta}(E) = \operatorname{Tr}\left[ \Gamma_{\alpha}G_t\Gamma_{\beta}G_t^\dagger\right], \tag*{(7)}
Tαi(E)=Tr⁡[1mσiGt†ΓαGt],(8)T^{\alpha i}(E) = \operatorname{Tr}\left[ \mathbf{1}_m\sigma_iG_t^\dagger\Gamma_{\alpha}G_t \right], \tag*{(8)}
Tiα(E)=Tr⁡[1mσiGtΓαGt†],(9)T^{i\alpha}(E) = \operatorname{Tr}\left[ \mathbf{1}_m\sigma_iG_t\Gamma_{\alpha}G_t^\dagger\right], \tag*{(9)}
Tij(E)=Tr⁡[1mσi(Gt†−Gt)1mσj(Gt−Gt†)],(10)T^{ij}(E) = \operatorname{Tr}\left[ \mathbf{1}_m\sigma_i(G_t^\dagger-G_t)\mathbf{1}_m\sigma_j(G_t-G_t^\dagger) \right], \tag*{(10)}

where Γα\Gamma_{\alpha} denotes the coupling to lead α\alpha, GtG_t is the retarded Green’s function of the time-frozen Hamiltonian, and 1m\mathbf{1}_m projects onto the lattice sites covered by the magnetic layer. In the present device geometry, no current flows into the magnetic layer. Consequently, all torque contributions arise from the net spin density accumulated at the device–magnet interface. The magnetization dynamics is therefore governed by the Landau–Lifshitz equation

∂m⃗∂t=−Δsurf2m⃗×s⃗(t).(11)\frac{\partial\vec{m}}{\partial t} = -\frac{\Delta_{\mathrm{surf}}}{2}\vec{m} \times\vec{s}(t). \tag*{(11)}

To identify different torque components, the transmission coefficients Tiα(E)T^{i\alpha}(E) are decomposed into parts that are even and odd under time-reversal symmetry:

Teiα(E)=Tiα(E)+Tαi(E)2,(12)T_{\mathrm{e}}^{i\alpha}(E) = \frac{T^{i\alpha}(E) + T^{\alpha i}(E)}{2}, \tag*{(12)}
Toiα(E)=Tiα(E)−Tαi(E)2.(13)T_{\mathrm{o}}^{i\alpha}(E) = \frac{T^{i\alpha}(E) - T^{\alpha i}(E)}{2}. \tag*{(13)}

References

Each of these components can be further classified according to its symmetry under bias reversal:

Te,νi(E)=TνiL(E)+TνiR(E)2,(14)T^{i}_{e,\nu}(E) = \frac{T^{iL}_{\nu}(E) + T^{iR}_{\nu}(E)}{2}, \tag*{(14)}
To,νi(E)=TνiL(E)−TνiR(E)2.(15)T^{i}_{o,\nu}(E) = \frac{T^{iL}_{\nu}(E) - T^{iR}_{\nu}(E)}{2}. \tag*{(15)}

The physical significance of the resulting symmetry-resolved torque components is summarised in Table I. For simplifying our simulations, we consider a constant anisotropy field strength.

(μ,ν)(\mu,\nu)SymmetryPhysical interpretation
(o,o)(o,o)Odd-oddField-like torque along (m⃗×σ⃗P)(\vec{m} \times\vec{\sigma}_{P})
(e,e)(e,e)Even-evenField-like torque along (m⃗×σ⃗P)(\vec{m} \times\vec{\sigma}_{P})
(o,e)(o,e)Odd-evenDamping like torque along m⃗×(m⃗×σ⃗P)\vec{m} \times(\vec{m} \times\vec{\sigma}_{P})
(e,o)(e,o)Even-oddVanishes identically

Table I. Physical interpretation of the symmetry-resolved spin–orbit torque components. The indices μ\mu and ν\nu denote the symmetry of the torque under bias-reversal and time-reversal operations, respectively.

The corresponding energy-resolved spin–orbit torques are then given by

τ⃗μ,ν(E)=−Δsurf2m⃗×T⃗μ,ν(E),(16)\vec{\tau}_{\mu,\nu}(E) = -\frac{\Delta_{\mathrm{surf}}}{2}\vec{m} \times\vec{T}_{\mu,\nu}(E), \tag*{(16)}

which are inserted into the Landau–Lifshitz equation to compute the magnetization dynamics. As illustrated in Figure 6b, the magnetization dynamics is obtained using a self-consistent iterative procedure. Starting from an initial magnetization configuration, the exchange term is constructed over the lattice sites covered by the magnetic layer and incorporated into the Hamiltonian. The resulting Hamiltonian is then used within the non-equilibrium Green’s function formalism to compute the spin density and the associated spin-orbit torques. These torques are subsequently used to evolve the magnetization via the Landau–Lifshitz equation, yielding an updated magnetization configuration. This procedure is repeated until a steady state is reached or for a fixed simulation time window.

Device schematic and flowchart of the methodology used

Figure 6. Device schematic and flowchart of the methodology used. (a) Schematic of the two-terminal device. The channel consists of monolayer WTe2_2 described by the Hamiltonian HH, connected to contacts Σ1,2\Sigma_{1,2} under an applied bias VbV_b. The monolayer is exchange-coupled to an adjacent magnetic layer with time-dependent magnetization m⃗(t)\vec{m}(t) via a surface exchange potential Δsurf\Delta_{\mathrm{surf}}. (b) Flowchart illustrating the simulation procedure for magnetization dynamics. At each time step, the exchange term in the Hamiltonian is calculated only over the lattice sites covered by the magnetic layer, which is then used within the non-equilibrium Green’s function (NEGF) formalism to compute the spin–orbit torque (SOT). The resulting torque is subsequently used in the Landau–Lifshitz equation to update the magnetization. This loop is repeated over the specified simulation time window.

References

  1. [1]S. Bhatti, R. Sbiaa, A. Hirohata, H. Ohno, S. Fukami, and S. N. P. R. P. N. P. ...DOI
  2. [2]D. Apalkov, B. Dieny, and J. M. Slaughter, Magnetoresistive random access memory, Proceedings of the IEEE 104, 1796 (2016).DOI
  3. [3]A. Manchon, J. Železný, I. M. Miron, T. Jungwirth, J. Sinova, A. Thiaville, K. Garello, and P. Gambardella, Current-induced spin-orbit torques in ferromagnetic and antiferromagnetic systems, Rev. Mod. Phys. 91, 035004 (2019).DOI
  4. [4]V. D. Nguyen, S. Rao, K. Wostyn, and S. Couet, Recent progress in spin-orbit torque magnetic random-access memory, npj Spintronics 2, 48 (2024).DOI
  5. [5]S. Ikegawa, F. B. Mancoff, J. Janesky, and S. Aggarwal, Magnetoresistive random access memory: Present and future, IEEE Transactions on Electron Devices 67, 1407 (2020).DOI
  6. [6]J. C. Slonczewski, Current-driven excitation of magnetic multilayers, Journal of Magnetism and Magnetic Materials 159, L1 (1996).DOI
  7. [7]L. Berger, Emission of spin waves by a magnetic multilayer traversed by a current, Phys. Rev. B 54, 9353 (1996).pubmed.ncbi.nlm.nih.gov/9984672
  8. [8]D. C. Worldledge and G.-H. Hu, Spin-transfer torque magnetoresistive random access memory technology status and future directions, Nature Reviews Electrical Engineering 1, 730 (2024).
  9. [9]V. Krizakova, M. Perumkunnil, S. Couet, P. Gambardella, and K. Garello, Spin-orbit torque switching of magnetic tunnel junctions for memory applications, Journal of Magnetism and Magnetic Materials 562, 169692 (2022).
  10. [10]V. Lopez-Dominguez, Y. Shao, and P. Khalili Amiri, Perspectives on field-free spin-orbit torque devices for memory and computing applications, J. Appl. Phys. 133, 040902 (2023).
  11. [11]I. M. Miron, K. Garello, G. Gaudin, P.-J. Zermatten, M. V. Costache, S. Auffret, G. B. Safarov, B. Rodmacq, A. Schulh, and P. Gambardella, Perpendicular switching of a single ferromagnetic layer induced by in-plane current injection, Nature 476, 189 (2011).
  12. [12]L. Liu, C.-F. Pai, Y. Li, H. W. Tseng, D. C. Ralph, and R. A. Buhrman, Spin-torque switching with the giant spin Hall effect of Tantalum, Science 336, 555 (2012).DOI
  13. [13]J. Sinova, S. O. Valenzuela, J. Wunderlich, C. H. Back, and T. Jungwirth, Spin Hall effects, Rev. Mod. Phys. 87, 1213 (2015).DOI
  14. [15]H. Wu, J. Zhang, B. Cui, S. A. Razavi, X. Che, Q. Pan, D. Wu, G. Yu, X. Han, and K. L. Wang, Field-free approaches for deterministic spin-orbit torque switching of the perpendicular magnet, Mater. Futures 1, 022201 (2022).DOI
  15. [16]Y.-C. Lau, D. Betto, K. Rode, J. M. D. Coey, and P. Stamenov, Spin-orbit torque switching without an external field using interlayer exchange coupling, Nat. Nanotechnol. 11, 758 (2016).DOI
  16. [17]W. He, C. Van, C. Zheng, Y. Wang, X. Wang, T. Ma, Y. Wang, C. Guo, X. Luo, M. E. Stebliy, G. Yu, Y. Liu, A. V. Ognev, A. S. Samardak, and X. Han, Field-free spin-orbit torque switching enabled by the interlayer Dzyaloshinskii-Moriya interaction, Nano Lett. 22, 6857 (2022).DOI
  17. [18]Z. Zheng, Y. Zhang, V. Lopez-Dominguez, L. Sánchez-Tejerina, J. Shi, X. Feng, L. Chen, Z. Wang, Z. Zhang, K. Zhang, B. Hong, Y. Xu, Y. Zhang, M. Carpentieri, A. Fert, G. Finocchio, W. Zhao, and P. Khalili Amiri, Field-free spin-orbit torque-induced switching of perpendicular magnetization in a ferrimagnetic layer with a vertical composition gradient, Nature Communications 12, 4555 (2021).
  18. [19]J. Zhou, L. Liu, X. Shu, W. Lin, T. Zhao, and J. Chen, Symmetry breaking by materials engineering for spin-orbit torque technology, IEEE Transactions on Magnetics 59, 1 (2023).
  19. [20]Y. Liu and Q. Shao, Two-dimensional materials for energy-efficient spin-orbit torque devices, ACS Nano 14, 9389 (2020).DOI
  20. [21]D. MacNeill, G. M. Stiehl, M. H. D. Guimaraes, R. A. Buhrman, J. Park, and D. C. Ralph, Control of spin-orbit torques through crystal symmetry in WTe2 / ferromagnet bilayers, Nature Physics 13, 300 (2017).
  21. [22]M.-G. Kang, S. Lee, and B.-G. Park, Field-free spin-orbit torques switching and its applications, npj Spintronics 3, 8 (2025).DOI
  22. [23]L. Pandey, B. Zhao, K. Tenzin, R. Ngaloy, V. Lamparská, H. Bangar, A. Ali, M. Abdel-Hafiez, G. Zhang, H. Wu, H. Chang, L. Sjöström, P. Rout, J. Sławińska, and S. P. Dash, Tunable unconventional spin orbit torque magnetization dynamics in van der waals heterostructures, Nature Communications 16, 8722 (2025).DOI
  23. [24]B. Zhao, R. Ngaloy, L. Pandey, H. Bangar, D. P. Dubey, and S. P. Dash, Nanoelectronics with two-dimensional magnets, Nano Letters 26, 7209 (2026).
  24. [25]S. Park, C. Kim, S. O. Park, N. K. Oh, U. Kim, J. Lee, J. Seo, Y. Yang, H. Y. Lim, S. K. Kwak, G. Kim, and H. Park, Phase engineering of transition metal dichalcogenides with unprecedentedly high phase purity, stability, and scalability via molten-metal-assisted intercalation, Adv. Mater. 32, 2001889 (2020).DOI
  25. [26]X. Qian, J. Liu, L. Fu, and J. Li, Quantum spin Hall effect in two-dimensional transition metal dichalcogenides, Science 346, 1344–1347 (2014).
  26. [27]K.-A. N. Duerloo, Y. Li, and E. J. Reed, Structural phase transitions in two-dimensional Mo- and W-dichalcogenide monolayers, Nat. Commun. 5, 4214 (2014).DOI
  27. [28]J. H. Garcia, M. Vila, C.-H. Hsu, X. Waintal, V. M. Pereira, and S. Roche, Canted persistent spin texture and quantum spin hall effect in WTe₂, Phys. Rev. Lett. 125, 256603 (2020).DOI
  28. [29]A. Lau, R. Ray, D. Varjas, and A. R. Akhmerov, Influence of lattice termination on the edge states of the quantum spin Hall insulator monolayer 1T′–WTe₂, Phys. Rev. Mater. 3, 054206 (2019).DOI
  29. [30]S. Tang, C. Zhang, D. Wong, Z. Pedramrazi, H.-Z. Tsai, C. Jia, B. Moritz, M. Claassen, H. Ryu, S. Kahn, J. Jiang, H. Yan, M. Hashimoto, D. Lu, R. G. Moore, C.-C. Hwang, C. Hwang, Z. Hussain, Y. Chen, M. M. Ugeda, Z. Liu, X. Xie, T. P. Deveareaux, M. F. Crommie, S.-K. Mo, and Z.-X. Shen, Quantum spin Hall state in monolayer 1T′-WTe₂, Nature Physics 13, 683 (2017).DOI
  30. [31]W. Zhao, E. Runburg, Z. Fei, J. Mutch, P. Malinowski, B. Sun, X. Huang, D. Pesin, Y.-T. Cui, X. Xu, J.-H. Chu, and D. H. Cobden, Determination of the spin axis in quantum spin Hall insulator candidate monolayer WTe₂, Phys. Rev. X 11, 041034 (2021).
  31. [32]Z. Fei, T. Palomaki, S. Wu, W. Zhao, X. Cai, B. Sun, P. Nguyen, J. Finney, X. Xu, and D. H. Cobden, Edge conduction in monolayer WTe₂, Nature Physics 13, 677–682 (2017).DOI
  32. [33]S. Wu, V. Fatemi, Q. D. Gibson, K. Watanabe, T. Taniguchi, R. J. Cava, and P. Jarillo-Herrero, Observation of the quantum spin Hall effect up to 100 kelvin in a monolayer crystal, Science 359, 76–79 (2018).DOI
  33. [34]Z.-Y. Jia, Y.-H. Song, X.-B. Li, K. Ran, P. Lu, H.-J. Zheng, X.-Y. Zhu, Z.-Q. Shi, J. Sun, J. Wen, D. Xing, and S.-C. Li, Direct visualization of a two-dimensional topological insulator in the single-layer 1T′-WTe₂, Phys. Rev. B 96, 041108(R) (2017).DOI
  34. [35]S. Wu, Y.-F. Liu, Y. S. Kwon, T. Y. Lim, S. Yeom, A. Gao, H. Li, R. R. Unocic, A. M. Varghese, E. Lopez-Torres, K. Xiao, T.-R. Chang, M. Yoon, S.-Y. Xu, and X. Li, Water-assisted layer growth of Tᵈ-phase WTe₂ for nonlinear Hall effect and microwave rectification, Nano Lett. 25, 17475 (2025).DOI
  35. [36]Q. Xie, W. Lin, S. Sarkar, X. Shu, S. Chen, L. Liu, T. Zhao, C. Zhou, H. Wang, J. Zhou, S. Gradečak, and J. Chen, Field-free magnetization switching induced by the unconventional spin-orbit torque from WTe₂, APL Mater. 9, 051114 (2021).DOI
  36. [37]L. Wei, X. Yin, P. Liu, P. Zhang, W. Niu, P. Liu, J. Yang, J. Peng, F. Huang, R. Liu, J. Chen, L. Chen, S. Zhou, F. Li, X. Niu, J. Du, and Y. Pu, Field-free spin-orbit torque-induced switching of perpendicular magnetization at room temperature in WTe₂/ferromagnet heterostructures, Appl. Phys. Lett. 123, 252404 (2023).arxiv.org/abs/2212.14281
  37. [38]I.-H. Kao, R. Muzzio, H. Zhang, M. Zhu, J. Gobbo, S. Yuan, D. Weber, R. Rao, J. Li, J. H. Edgar, J. E. Goldberg, J. Y. Yan, D. G. Mandrus, J. Hwang, R. Cheng, J. Katoch, and S. Singh, Deterministic switching of a perpendicularly polarized magnet using unconventional spin-orbit torques in WTe₂, Nat. Matter. 21, 1029 (2022).DOI
  38. [39]X.-G. Ye, P.-F. Zhu, W.-Z. Xu, N. Shang, K. Liu, and Z.-M. Liao, Orbit-transfer torque driven field-free switching of perpendicular magnetization, Chin. Physics Lett. 39, 037303 (2022).DOI
  39. [40]S. N. Kajale, T. Nguyen, N. T. Hung, M. Li, and D. Sarkar, Field-free deterministic switching of all-van der Waals spin-orbit torque system above room temperature, Sci. Adv. 10, eadk8669 (2024).DOI
  40. [41]L. Wang, J. Xiong, B. Cheng, Y. Dai, F. Wang, C. Pan, T. Cao, X. Liu, P. Wang, M. Chen, S. Yan, Z. Liu, J. Xiao, X. Xu, Z. Wang, Y. Shi, S.-W. Cheong, H. Zhang, S.-J. Liang, and F. Miao, Cascadable in- L. V. Keldysh, Diagram Technique for Nonequilibrium Processes, Sov. Phys. JETP 20, 1018 (1965).
  41. [43]M. Soleimani, S. Jalili, F. Mahfouzi, and N. Kioussis, Spin-orbit torque-driven magnetization switching in 2D-topological insulator heterostructure, Europhysics Letters 117, 37001 (2017).DOI
  42. [44]F. Mahfouzi, B. K. Nikolić, and N. Kioussis, Anti-damping spin-orbit torque driven by spin-flip reflection mechanism on the surface of a topological insulator: A time-dependent nonequilibrium Green function approach, Phys. Rev. B 93, 115419 (2016).
  43. [45]S. Tapar, B. Weber, S. P. Dash, S. Mukherjee, and B. Muralidharan, Symmetry driven spin anisotropic magnetotransport in quantum spin Hall insulator WTe₂ 1T (2025), arXiv:2507.18543 [cond-mat.mes-hall].arxiv.org/abs/2507.18543
  44. [46]C. W. Groth, M. Wimmer, A. R. Akhmerov, and X. Waintal, Kwant: a software package for quantum transport, New J. Phys. 16, 063065 (2014).
  45. [47]B. K. Nikolic, K. Dolui, M. Petrovic, P. Plecháč, T. Markussen, and K. Stokbro, First-principles quantum transport modeling of spin-transfer and spin-orbit torques in magnetic multilayers (2018), arXiv:1801.05793 [cond-mat.mes-hall].DOI
  46. [48]M. Hu, G. Ma, C. Y. Wan, and J. Liu, Realistic tight-binding model for monolayer transition metal dichalcogenides of 1T′ structure, Phys. Rev. B 104, 035156 (2021).DOI

Paper details

vlnc:W_c23vd7xz
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents