betaFeedback

WorksPhysics and Astronomy

Controllable suppression of the unconventional superconductivity in bulk and thin-film Sr2_{2}RuO4_{4} via high-energy electron irradiation

Abstract

In bulk Sr2_{2}RuO4_{4}, the strong sensitivity of the superconducting transition temperature TcT_{\text{c}} to nonmagnetic impurities provides robust evidence for a superconducting order parameter that changes sign around the Fermi surface. In superconducting epitaxial thin-film Sr2_{2}RuO4_{4}, the relationship between TcT_{\text{c}} and the residual resistivity ρ0ρ_0, which in bulk samples is taken to be a proxy for the low-temperature elastic scattering rate, is far less clear. Using high-energy electron irradiation to controllably introduce point disorder into bulk single-crystal and thin-film Sr2_{2}RuO4_{4}, we show that TcT_{\text{c}} is suppressed in both systems at nearly identical rates. This suggests that part of ρ0ρ_0 in films comes from defects that do not contribute to superconducting pairbreaking, and establishes a quantitative link between the superconductivity of bulk and thin-film samples.

Introduction

Conclusive identifications of the order parameter and of the interactions that induce superconductivity in Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 have remained elusive despite receiving intense research interest for more than 25 years [1, 2]. Among the first evidence for the unconventional nature of superconductivity in Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 was the observation that the transition temperature TcT_c could be completely suppressed with a minute concentration of nonmagnetic impurities [3], indicating that the phase of the superconducting order parameter changes sign in momentum space and, with sufficient scattering, averages to zero [1]. Subsequent studies confirmed this extreme sensitivity to disorder, either by introducing variable defect densities via intentional chemical substitutions during growth [4, 5, 6] or by taking advantage of native impurities and structural defects that exist in all nominally stoichiometric crystals [7, 8].

While the basic fact of the unconventionality is well established, determining the specific symmetry of the order parameter in Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 continues to be challenging, not least because of the intrinsically low energy scales of the problem, with Tc≲1.5T_c \lesssim1.5 K. In principle, using epitaxial thin films of Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 as a materials platform would offer a new angle of attack with numerous potential advantages: films can be patterned using standard optical lithography into devices and junctions for phase-sensitive magnetization and electrical transport measurements [9, 10], and are naturally compatible with sophisticated scanned-probe microscopies [11, 12] and spectroscopic techniques [13, 14]. Indeed, in the cuprate high-temperature superconductors, scanning SQUID microscopy of thin-film samples provided conclusive evidence of the dx2−y2d_{x^2-y^2} pairing symmetry [15].

The strong sensitivity of Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 to disorder meant that it required many years of effort following the initial discovery of superconductivity in Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 single crystals [16] for the materials science community to realize epitaxial thin films of Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 that were electronically clean enough to exhibit superconductivity [17]. Now that superconducting thin-film samples can be reproducibly synthesized [18, 19, 20, 21], there is an urgent need to establish a quantitative link between the physical properties of single crystals and the best thin films. The essential challenge in doing so is that the correlation between TcT_c and the residual resistivity ρ0\rho_0—taken in bulk samples to be a proxy for the low-temperature elastic scattering rate—of as-grown films is not nearly as robust as that observed in single crystals.

One hypothesis to explain the difference between the two forms of Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 is that epitaxial thin films contain extended in-plane defects, such as small-angle grain boundaries, that increase the electrical resistivity but have a much smaller effect on the intrinsic intra-grain quasiparticle scattering rate and hence on TcT_c. To test this hypothesis would require a means of introducing point disorder to such films while, hopefully, generating as small a change as possible to the resistivity of the extended defects.

Here, we use high-energy electron irradiation to controllably introduce point disorder into bulk single-crystal and thin-film Sr2_2RuO4_4. We establish that the disorder from irradiation suppresses TcT_c in bulk Sr2_2RuO4_4 in the same way as chemical substitution or native point defects, but with far greater control over the disorder axis. We then demonstrate that thin films respond to irradiation-induced disorder in essentially the same way as bulk samples, with TcT_c being suppressed in crystals and films at nearly identical rates.

Methods

FIB-sculpted single crystals of Sr2_2RuO4_4

To prepare samples of bulk, single-crystal Sr2_2RuO4_4 that were compatible with high-energy electron irradiations and that enabled reliable measurements of the low-temperature resistivity, we used a modified version of the epoxy-free method of mounting and preparing microstructures described in Ref. [22]. Procedures for the growth of the Sr2_2RuO4_4 crystals are described in Ref. [23].

From an oriented slice of the parent crystal, we cleaved a piece of Sr2_2RuO4_4 having ⟨100⟩\langle100\rangle-oriented edges to expose a flat, (001)-oriented surface which later became the top surface of the finished microstructure. To make electrical contact, we sputtered 200 nm of gold onto the cleaved surface and annealed the crystal for 5 to 6 minutes at 500°C in air. We then used a focused ion beam (FIB) to extract lamellae (typical dimensions about 200 μ\mum ×\times 160 μ\mum ×\times 6 μ\mum), working from the uncleaved side inwards, and transferred these lamellae ex situ onto mica substrates with the Au-coated surface facing upwards. After depositing 10 nm of Ti and another 150 nm of Au onto each lamella, we deposited Pt bridges in a xenon plasma-FIB to join the top of each lamella to the mica substrate. We then deposited a final 10 nm Ti/150 nm Au to ensure good electrical contact between the lamella and the gold film on the mica substrate.

After mounting and contacting the lamellas, we used a gallium FIB to pattern each into a meandering microstructure suitable for four-point resistance measurements, as shown in Figure 1(a). From the dimensions of each microstructured Sr2_2RuO4_4 bar [24], we calculated the appropriate geometrical factors to convert the measured resistances into resistivities. Such FIB-sculpted bars of Sr2_2RuO4_4 have a well-defined shape and the positions of the voltage-sensing contacts on the crystal are independent of the wires and epoxy used for connecting the sample to external electronics equipment in subsequent resistance measurements. The latter point is important because the wires attached to the mica substrate must be removed and remade every time the sample is transferred between the cryostat used for low-temperature electrical transport experiments and that used for electron irradiation experiments. Having a stable, reproducible geometry for the resistance measurement is essential for detecting small, irradiation-induced changes in the absolute resistivity.

Figure 1. Effects of high-energy electron irradiation on the electrical resistivity and superconducting TcT_c of Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4. (a) Scanning electron microscope image of a single crystal of bulk Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 that was microstructured with a focused ion beam. (b) Optical microscope image of many resistivity bridges lithographically patterned on an epitaxial thin-film sample of Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4. (c) Resistivity versus temperature at T≤2T \le2 K for the crystal shown in (a), before and after the sample received a 0.45 C/cm2^2 dose of 2.5 MeV electron irradiation. The irradiation causes an increase in ρ0\rho_0 from 0.13 μΩ\mu\Omega-cm to 0.45 μΩ\mu\Omega-cm and a decrease in TcT_c from 1.35 K to 0.97 K. (d) Resistivity versus temperature data measured for a representative thin-film bridge, before and after a 0.45 C/cm2^2 dose of 2.5 MeV electron irradiation. Inset shows a zoomed-in view of ρ(T)\rho(T) for T<2T < 2 K: irradiation induces an increase in ρ0\rho_0 from 1.14 μΩ\mu\Omega-cm to 1.56 μΩ\mu\Omega-cm and a decrease in TcT_c from 1.40 K to 0.79 K.

Epitaxial thin films of Sr2_2RuO4_4

For our experiments on thin-film Sr2_2RuO4_4, we synthesized a (001)-oriented film of Sr2_2RuO4_4 on a (110)-oriented NdGaO3_3 substrate (Crystec, GmbH) by molecular beam epitaxy following the substrate preparation and adsorption-controlled film growth procedures detailed in Refs. [19, 25]. After preliminary structural characterization of the Sr2_2RuO4_4/NdGaO3_3(110) wafer via x-ray diffraction [24], we used standard photolithography, sputter deposition, and ion milling techniques to pattern the Sr2_2RuO4_4 film into many standalone devices for electrical resistivity measurements, as described in Ref. [10]. As shown in Figure 1(b), the region of the wafer patterned in this way is about 6 mm ×\times 4 mm in lateral extent, and each device occupies a total areal footprint of 1 mm ×\times 1 mm, thus allowing many bridges to be fabricated from the same film.

Each resistivity bridge consists of two Pt (25 nm)/Ti (5 nm) contact pads at its ends for current injection and removal, and two Pt/Ti pads in the middle for attaching voltage-sensing wires, separated by a center-to-center distance of L=200L = 200 μ\mum. Mismatch between the lattices of Sr2_2RuO4_4 and the (110) surface of NdGaO3_3 imposes in-plane, uniaxial and biaxial strains on the Sr2_2RuO4_4 film; at 295 K, the two Ru-O-Ru bonding directions along xx and yy are compressed by −0.39%-0.39\% and −0.16%-0.16\% relative to unstrained, bulk single crystals of Sr2_2RuO4_4 (a=3.8694a = 3.8694 Å) [26, 27], corresponding to in-plane A1gA_{1g} and B1gB_{1g} strains of −0.28%-0.28\% and 0.23%0.23\%. The longest dimension of every resistivity bridge is aligned with the slightly longer of the two in-plane Ru-O-Ru bond directions. Since the NdGaO3_3 substrate is a wide-band-gap electrical insulator, the cross-sectional area through which the current is constricted to flow through is the Sr2_2RuO4_4 film thickness, t=28.1±1.3t = 28.1 \pm1.3 nm, multiplied by the width of the resistivity bridges as determined by the lithography, w=80w = 80 μ\mum. All of the physical dimensions of the thin-film resistivity bridges are significantly larger than the characteristic mean free paths of the charge carriers in Sr2_2RuO4_4 along the corresponding crystallographic directions, so we expect Ohmic conduction to dominate the charge transport response at all temperatures.

We diced the patterned wafer into individual pieces containing one or two devices and mechanically polished each of these smaller pieces down from the backside until the NdGaO3_3 substrate was reduced to a thickness of 100 to 200 μ\mum. Each piece could then be handled and irradiated separately from the others; the substrate-thinning step allowed the irradiation to penetrate the full thickness of the film and substrate without causing excessive attenuation of the beam. Throughout the main text and Supplemental Material [24], we refer to individual Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 thin-film resistivity bridges separated out in this way from the same original wafer as distinct as-grown samples. Comprehensive electrical characterization of these as-grown samples is described in the Supplemental Material [24].

Electrical transport measurements

We measured four-point resistances of the Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 epitaxial thin films and FIB-sculpted single crystals using standard ac techniques at excitation frequencies less than 200 Hz, employing a multichannel lock-in amplifier (Synktek) and dual-ended current sources with active common mode rejection [28]. Unless otherwise noted, we used bias currents of Irms≤10I_{\rm rms} \le10 μ\muA for resistance measurements.

surements.

We controlled the sample temperature and external magnetic field using a Physical Properties Measurement System (Quantum Design) equipped with a helium-3 insert and a 14 Tesla superconducting magnet. To ensure uniform thermalization of the samples upon traversing the superconducting transitions, we incremented the temperature gradually at low temperatures: typical cooling/warming rates for thermal cycles between 0.4 K and 2 K were about 1 K/hour. Detailed explanations of the definitions and analysis methods that we used to extract ρ0\rho_0 and TcT_c from resistivity versus temperature data can be found in [24].

High-energy electron irradiation

We performed high-energy electron irradiations (Eincident=2.5E_{\rm incident} = 2.5 MeV) at the SIRIUS Pelletron linear accelerator in Palaiseau, France, following the procedures described in [22]. The FIB-sculpted single-crystal and epitaxial thin-film samples all had the cc-axis of the Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 crystal structure aligned with the out-of-plane direction, along which the electron beam propagated. The samples were immersed in a bath of liquid hydrogen at a temperature of 22 K during irradiation in order to produce a random distribution of vacancy-interstitial Frenkel pairs [29]. Maintaining low temperatures during electron irradiation promotes the formation of immobile, pointlike defects, without appreciable defect clustering, cascades, columnar defects, or other extended spatial correlations [30]. Measurements of the upper critical field of films before and after irradiation (Appendix B) confirm that the irradiation-induced defects are pointlike.

Using NIST tables [31] to calculate the electron stopping power of Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 in the continuous-slowing-down approximation, we estimate the stopping length of the 2.5 MeV electrons to be 2.9 mm in Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4, meaning that the irradiation-induced defects should be homogeneously distributed throughout the entire thickness of all samples studied here. According to the standard electron-scattering formalism, we expect that 2.5 MeV electrons transfer sufficient energy to the atoms in the crystal structure to create vacancy-interstitial Frenkel pairs on all four unique sublattices in Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4 (i.e., strontium, ruthenium, equatorial oxygen, and apical oxygen), albeit with higher production rates for the cations than for either oxygen site based on likely values for the interaction cross-sections (Appendix A).

The electron irradiation facility in Palaiseau allows for in situ electrical resistance measurements to be conducted during irradiation, with the sample held at constant T=22T = 22 K. Data of this kind are shown in Appendix A for representative epitaxial thin-film and FIB-sculpted single-crystal samples of Sr2RuO4\mathrm{Sr}_2\mathrm{RuO}_4, and allow for perhaps the most straightforward comparison with theories that attempt to model cross sections for Frenkel pair production, based on tabulated cross sections for electron scattering from different nuclei and the displacement energies of the nuclei away from the unique chemical bonding sites in question.

All low-temperature (T<22T < 22 K) electrical transport data on irradiated samples shown in this work, however, were acquired after ex situ transfers of the samples from the cryostat at the irradiation facility to different cryostats at the Max Planck Institute for Chemical Physics of Solids in Dresden, Germany, which required warming up the samples to room temperature. This initial “room-temperature annealing” step causes recombination of some of the irradiation-induced Frenkel pairs, as well as migration of some of the interstitials created during irradiation to various other sinks in the materials, such as surfaces, grain boundaries, and/or dislocations. Nevertheless, quasi-equilibrium populations of irradiation-induced vacancies and interstitials remain after the initial warmup to room temperature that are robust against further thermal cycles between 0 and 300 K. It is the cumulative effect of the latter point-like scattering centers on the charge transport and superconductivity in Sr2_2RuO4_4 that we attempt to quantify when investigating the dose dependencies of ρ0\rho_0 and TcT_\mathrm{c}.

Results

In Figure 1(c,Figure 1d), we show that a moderate e−e^- dose of 2.5 MeV electron irradiation (D=0.45D = 0.45 C/cm2^2 = 2.8×10182.8 \times10^{18} e−e^- /cm2^2) subtly perturbs the electrical resistivity ρ(T)\rho(T) of Sr2_2RuO4_4. At low temperatures, where other, presumably inelastic, charge-carrier scattering mechanisms become frozen out by phase-space constraints, the effects of irradiation on ρ\rho become proportionally more relevant and noticeable. The irradiation-induced modification of the elastic transport scattering rate, as measured by the change in residual resistivity Δρ0\Delta\rho_0, reduces the superconducting TcT_\mathrm{c} while largely preserving the sharpness of the superconducting transitions, indicating that the irradiation-induced defects are distributed homogeneously throughout the samples over the characteristic coherence length scales {ξab,ξc}\{\xi_{ab}, \xi_c\} of the Cooper pairs. The initial rates of ρ0\rho_0 increase and of TcT_\mathrm{c} suppression with e−e^- dose are similar for the FIB-sculpted single crystal of Sr2_2RuO4_4 and for the 28-nm Sr2_2RuO4_4/NdGaO3_3(110) epitaxial thin-film sample.

Magnetoresistance measurements of the upper critical fields for superconductivity and of Shubnikov-de Haas oscillations for electron-irradiated Sr2_2RuO4_4 thin films (Appendix B) provide additional evidence for the spatial uniformity and point-like nature of the irradiation-induced defects, and show that the primary effect of this additional disorder is to boost the rate at which the momentum of the charge-current-carrying excitations is relaxed, while preserving the itinerant charge-carrier densities (i.e., band occupancies) as well as other salient features of the normal-state electronic structure near the Fermi level, such as the quasiparticle velocities.

Having established the qualitative effects of high-energy electron irradiation on some of the basic properties of the superconducting and correlated-metal states in Sr2_2RuO4_4, we now turn our attention to a detailed investigation of e−e^--dose-dependent changes of ρ0\rho_0 and TcT_\mathrm{c}. We leave direct microscopic visualization of the irradiation-induced disorder in Sr2_2RuO4_4 to future studies, because detecting dilute concentrations of point-like defects, on the order of one part per thousand, is a notoriously challenging task, well beyond the current capabilities of state-of-the-art microstructural probes such as scanning transmission electron microscopy [32, 33].

Given that substitutional disorder on the Ru site has been shown to increase ρ0\rho_0 at approximately 10×10\times the rate of substitutional disorder on the Sr site [4, 5, 6], we infer that Ru vacancies (produced at a rate of 1.21.2 to 2.6×10−32.6 \times10^{-3} displacements per Ru atom per 11 C/cm2^2 of irradiation) account for most of the observed modifications to ρ0\rho_0. We provide a detailed discussion of the conversions between DD and Frenkel defect densities, and an analysis of the likely contributions of these defects to ρ0\rho_0, in Appendix A.

In Figure 2(a), we plot the relative irradiation-induced changes in ρ0\rho_0 measured across four distinct FIB-sculpted single-crystal samples of Sr2_2RuO4_4 as a function of the accumulated dose DD of 2.52.5 MeV electron irradiation, and in Figure 2(c) we plot the resistively measured TcT_{\mathrm{c}} versus DD for all of these samples, before and after irradiation. In Figure 2(b,Figure 2d), we plot the same quantities as in Figure 2(a,Figure 2c), except now for nine distinct 2828-nm Sr2_2RuO4_4/NdGaO3_3(110) thin-film samples. Raw ρ(T)\rho(T) curves for all thin-film samples that underlie the data points in Figure 2(b,Figure 2d) are presented in the Supplemental Material [24]. For both types of Sr2_2RuO4_4 samples, there are clear systematic effects of DD on both Δρ0,irr\Delta\rho_{0,\mathrm{irr}} and TcT_{\mathrm{c}}, that further corroborate the trends suggested by the data and samples highlighted in Figure 1: precisely controlled increases in DD cause nearly monotonic increases in ρ0\rho_0 that are accompanied by precisely controlled, smooth decreases in TcT_{\mathrm{c}}.

Irradiation dose dependencies of residual resistivity and superconducting transition temperature

Figure 2. Irradiation dose dependencies of ρ0\rho_0 and TcT_\mathrm{c} in Sr2_2RuO4_4 epitaxial thin films and single crystals. (a,b) Relative change in residual resistivity Δρ0,irr(D)≡ρ0,after irr(D)−ρ0,as grown\Delta\rho_{0,\mathrm{irr}}(D) \equiv\rho_{0,\mathrm{after\ irr}}(D) - \rho_{0,\mathrm{as\ grown}} induced per unit e−e^- dose DD of 2.5 MeV electron irradiation in (a) microstructured bulk single crystals and (b) thin films after a single round of irradiation. Each data point represents a physically distinct sample. Linear fits of all available data points are shown as solid gray lines; the shaded region bounded by dashed lines indicates ±2σ\pm2\sigma uncertainties in the fitted slope of the best-fit line for each data set. (c,d) Resistively-measured superconducting TcT_\mathrm{c} versus accumulated e−e^- dose DD for the irradiated samples displayed in panels (a,b) (teal markers), as well as the as-grown TcT_\mathrm{c}s for the same samples (dark blue markers clustered at D=0D = 0). Here TcT_\mathrm{c} is defined as the temperature at which ρ(T)\rho(T) crosses the 50% threshold of ρ0\rho_0, and vertical error bars on each thin-film TcT_\mathrm{c} square in (d) indicate the temperatures at which ρ(T)\rho(T) crosses the 10% and 80% thresholds of ρ0\rho_0; error bars defined analogously for the single-crystal TcT_\mathrm{c} in (c) are smaller than the heights of the corresponding midpoint TcT_\mathrm{c} squares. In panels (c,d), irradiated samples having TcT_\mathrm{c}s below the base temperatures of the measurement cryostats (horizontal black dashed lines) are drawn as open squares, and were not included in the linear fits of Tc(D)T_\mathrm{c}(D) drawn as solid gray lines [dashed gray lines have the same meaning as in panels (a,b)]. The vertical and horizontal scales of the single-crystal graphs in (a,c) are identical to the corresponding thin-film graphs in (b,d) to facilitate visual comparisons between the data sets.

For the FIB-sculpted Sr2_2RuO4_4 single-crystal sample that received the highest irradiation dose in Figure 2(a,Figure 2c) (D=1.18D = 1.18 C/cm2^2), such a dose was sufficient to reduce TcT_{\mathrm{c}} from its as-grown value of 1.521.52 K to a post-irradiation value that was less than the base temperature of the cryostat (in this case, an adiabatic demagnetization insert for the PPMS), Tc<0.25T_{\mathrm{c}} < 0.25 K. Accordingly, we schematically display this sample in Figure 2(c) as open square markers consistent with a range of possible TcT_{\mathrm{c}}s between 00 and 0.250.25 K. This sample was not included in fits to Tc(D)T_{\mathrm{c}}(D) described below, but it provides an illustrative example that highlights the stringent requirements on sample purity for observing superconductivity in Sr2_2RuO4_4: an extremely small (in absolute terms) increase of the quasiparticle scattering rate by Δρ0=0.83\Delta\rho_0 = 0.83 μΩ\mu\Omega-cm is sufficient to suppress TcT_{\mathrm{c}} from near its maximally-achievable value to almost zero. Likewise, for the Sr2_2RuO4_4 thin-film samples that accumulated the highest irradiation doses in Figure 2(b,Figure 2d) (D=0.80D = 0.80 C/cm2^2 and 1.001.00 C/cm2^2), we did not observe superconductivity in ρ(T)\rho(T) data collected down to the base temperature of the helium-3 cryostat, 0.40.4 K. We do not include these points in subsequent fits to Tc(D)T_{\mathrm{c}}(D), and we leave a more comprehensive exploration of the regime of very low TcT_{\mathrm{c}}s to future work.

To provide the simplest-possible quantitative parameterizations of these dose dependencies, we assume that Δρ0,irr\Delta\rho_{0,\mathrm{irr}} and TcT_{\mathrm{c}} should initially vary linearly with DD over the investigated ranges of e−e^- doses in Figure 2, because all DD here correspond to dilute concentrations of irradiation-induced defects, of the order of 0.1%0.1\% (Appendix A). Fitting the data points in Figure 2 to lines, and taking systematic error bars on the fit coefficients to be ±2σ\pm2\sigma surrounding the best-fit values, we obtain the curves summarized in Table I. Alternatively, the explicit dependencies of Δρ0\Delta\rho_0 and ΔTc\Delta T_{\mathrm{c}} on DD can be eliminated by taking the ratios of the slopes of the best-fit lines, which yields ΔTc/Δρ0=(−1.24±0.08)\Delta T_{\mathrm{c}}/\Delta\rho_0 = (-1.24 \pm0.08) K/μΩ\mu\Omega-cm for bulk crystals and (−1.23±0.19)(-1.23 \pm0.19) K/μΩ\mu\Omega-cm for the thin films.

In other words, although the individual magnitudes of both of the rates Δρ0/ΔD\Delta\rho_0/\Delta D and ∣ΔTc/ΔD∣|\Delta T_{\mathrm{c}}/\Delta D| for the Sr2_2RuO4_4/NdGaO3_3(110) epitaxial thin-film samples are greater, in a statistically significant sense, than the corresponding rates for the FIB-sculpted single crystal Sr2_2RuO4_4 samples, these differences essentially compensate each other when taking the ratio of these quantities, resulting in initial rates of TcT_{\mathrm{c}} suppression with increasing residual resistivity, ΔTc/Δρ0\Delta T_{\mathrm{c}}/\Delta\rho_0, for the two types of Sr2_2RuO4_4 samples that are indistinguishable within experimental precision.

Discussion

In Figure 3, we plot 2222 (ρ0,Tc)(\rho_0, T_{\mathrm{c}}) data points extracted from the literature as gray circles for bulk single crystals of Sr2_2RuO4_4 containing natively occurring (as-grown) defects [3], deliberate substitutions of Ir or O on the Ru site [5], as well as deliberate substitutions of La on the Sr site [6]. Results for electron-irradiated FIB-sculpted single crystals of Sr2_2RuO4_4 from the present work are overlaid as dark purple squares on these reference data points. For the e−e^--irradiated crystals, several repetitions of the cycle of {measure ρ(T)→irradiate→remeasure ρ(T)}\{\text{measure }\rho(T) \rightarrow\text{irradiate} \rightarrow\text{remeasure }\rho(T)\} allowed us to use the same physical samples to acquire multiple (ρ0,Tc)(\rho_0, T_{\mathrm{c}}) data points—hence the larger number of data points shown in Figure 3 (1111 in total) than in Figure 2(b,Figure 2d)—which, taken together, span nearly the entire range of disorder over which superconductivity is observed in unstrained bulk single crystals of Sr2_2RuO4_4. The overall trend of the previously reported Tc(ρ0)T_{\mathrm{c}}(\rho_0) dependence is reproduced well, with the more precisely clustered data from this work suggesting a slightly steeper slope of the best-fit line than previously, as seen by comparing the purple and gray solid lines in Figure 3.

Figure 3. Universal impact of elastic, momentum-relaxing scattering on superconductivity in Sr2_2RuO4_4. Gray circles represent previously published data for bulk single-crystal samples of Sr2_2RuO4_4 containing native defects [3], as well as intentionally-substituted chemical impurities on the Ru and Sr sites—viz., Sr2_2(Ru1−x_{1-x}Tix_x)O4_4 [5], Sr2_2(Ru1−x_{1-x}Irx_x)O4_4 [5], and (Sr2−y_{2-y}Lay_y)RuO4_4 [6]. Dark purple squares represent results from this work for e−e^{-}-irradiated Sr2_2RuO4_4 single crystals containing native defects plus irradiation-induced vacancy-interstitial Frenkel pairs on all atomic sublattices. For all single-crystal data shown here, the measured residual resistivity in absolute units, ρ0\rho_0 [μΩ\mu\Omega-cm], is utilized as a proxy assumed to be directly proportional to the Cooper-pairbreaking energy scale, ℏ/τpb\hbar/\tau_{\mathrm{pb}}, with no adjustments of the common zero point of these scales (bottom axis). On the other hand, results from this work for e−e^{-}-irradiated 28-nm Sr2_2RuO4_4/NdGaO3_3(110) epitaxial thin-film samples are plotted as red squares against the irradiation-induced change in residual resistivity, Δρ0,irr\Delta\rho_{0,\mathrm{irr}} [μΩ\mu\Omega-cm] (top axis). As explained in the main text, a range of rigid shifts of the zero point of the top axis relative to the bottom axis are, in principle, compatible with the results of this work; here we chose an offset of +0.5 μΩ+0.5\ \mu\Omega-cm for visual clarity, indicated by the red arrow in the upper left corner. Color-coded straight lines are linear fits to each family of Sr2_2RuO4_4 samples and the systematic uncertainties in the best-fit rates of TcT_c suppression (±1σ\pm1\sigma) are indicated by the color-coded shaded regions between dashed lines.

The TcT_{\mathrm{c}} data points for all Sr2_2RuO4_4 single-crystal samples in Figure 3 are plotted versus the absolute residual resistivity ρ0\rho_0, without any shift in the zero point of this scale. Implicit in this choice is the assumption that all sources of quasiparticle scattering that contribute to ρ0\rho_0, both intrinsically present from the original crystal growth and induced by irradiation, also contribute proportionally to the Cooper-pair-breaking energy scale ℏ/τpb\hbar/\tau_{\mathrm{pb}}, and thus to the suppression of TcT_{\mathrm{c}}. This assumption is justified by the limited scatter in the Tc(ρ0)T_{\mathrm{c}}(\rho_0) behavior observed across different studies, and by the inferred extrapolation of the experimental data to a common range of zero-disorder Tc0=1.5T_{\mathrm{c0}} = 1.5 to 1.551.55 K, which are furthermore consistent with the highest values of TcT_{\mathrm{c}} found in the literature for actual Sr2RuO4\mathrm{Sr_2RuO_4} crystals under ambient conditions.

Sample typeΔρ0(D)\Delta\rho_0(D)Range of fit in DDΔTc(D)\Delta T_c(D)Range of fit in DD
Bulk single crystal(0.70±0.02)D(0.70 \pm0.02)D[0.3,1.18][0.3, 1.18](1.34±0.02)−(0.86±0.07)D(1.34 \pm0.02) - (0.86 \pm0.07)D[0,0.6][0, 0.6]
28 nm Sr2RuO4/NdGaO3(110)\mathrm{Sr_2RuO_4}/\mathrm{NdGaO_3}(110) films(1.00±0.13)D(1.00 \pm0.13)D[0.2,1.0][0.2, 1.0](1.38±0.02)−(1.22±0.06)D(1.38 \pm0.02) - (1.22 \pm0.06)D[0,0.6][0, 0.6]

Table I. Linear fits to the dose dependencies of ρ0\rho_0 and of TcT_c plotted in Figure 2(a,Figure 2b) and Figure 2(c,Figure 2d), respectively. Error bars on the fit coefficients are ±2σ\pm2\sigma. Units: ρ0\rho_0 [μΩ\mu\Omega-cm], TcT_c [K], DD [C/cm2^2].

In contrast, the relatively large scatter in the initial absolute values of ρ0\rho_0 across nine distinct as-grown Sr2RuO4\mathrm{Sr_2RuO_4} thin films (1.1 to 1.5 μΩ\mu\Omega-cm [24]) is incommensurate with the narrow distribution of as-grown TcT_cs for these same samples (1.35 to 1.41 K). An assumption of direct proportionality between ρ0\rho_0 and ℏ/τpb\hbar/\tau_{\mathrm{pb}} is therefore not appropriate for the thin-film samples. Nevertheless, while there is no discernible correlation between absolute values of ρ0\rho_0 and TcT_c, the changes in ρ0\rho_0 and TcT_c after being subjected to different doses of 2.5 MeV electron irradiation, Δρ0\Delta\rho_0 and ΔTc\Delta T_c, respond in a highly correlated fashion, in a way that is similar to the dose-dependent trends that we observed on FIB-sculpted single crystals. The most intuitive way to reconcile these observations is to assume that many of the natively occurring extended defects in as-grown Sr2RuO4\mathrm{Sr_2RuO_4} thin films [10, 18, 19, 20, 21, 33, 34, 35, 36] contribute to ρ0\rho_0 but do not contribute appreciably to TcT_c suppression, whereas any pointlike defects, including those created by electron irradiation, cause both ρ0\rho_0 and ℏ/τpb\hbar/\tau_{\mathrm{pb}} to rapidly increase in lockstep, just as in bulk crystals.

The natural interpretation of the thin-film data as reflecting a separation of independent sources of scattering that couple differently to ρ0\rho_0 and TcT_c therefore suggests that our irradiation experiments should still accurately probe the Cooper-pair-breaking rate of TcT_c suppression, ΔTc/Δ(ℏ/τpb)∝ΔTc/Δρ0\Delta T_c/\Delta(\hbar/\tau_{\mathrm{pb}}) \propto\Delta T_c/\Delta\rho_0, in thin films, provided that the relative change in ρ0\rho_0 is measured pairwise for the same thin-film sample before and after each sample accumulates a given dose DD of electron irradiation (Appendix § 2.3 and Figure 7). Following this line of reasoning, we combine the data for the as-grown and electron-irradiated 28-nm Sr2RuO4/NdGaO3(110)\mathrm{Sr_2RuO_4}/\mathrm{NdGaO_3}(110) thin-film samples previously shown in Figure 2(b,Figure 2d) and replot these 18 TcT_c data points as red squares against the top axis of Figure 3, Δρ0,irr\Delta\rho_{0,\mathrm{irr}}, thereby eliminating the explicit dependence on the dose DD of 2.5 MeV electron irradiation. By employing the same units of [μΩ\mu\Omega-cm] for the quasiparticle scattering rates on the top and bottom axes in Figure 3, we do not allow for any arbitrary scale factors in comparing the Sr2RuO4\mathrm{Sr_2RuO_4} thin-film and single-crystal results.

Figure 7. TcT_c versus absolute ρ0\rho_0 for Sr2_2RuO4_4 single crystals and epitaxial thin films. For Sr2_2RuO4_4 single crystals, purple square markers from the electron-irradiation experiments detailed in this work and gray circular markers extracted from impurity-scattering studies in the literature [3, 5, 6] are reproduced from Figure 3 of the main text. For Sr2_2RuO4_4 thin films, the red square markers plotted here are obtained directly from ρ(T)\rho(T), without the shift in the horizontal axis used in Figure 3. Red lines connect pairs of (ρ0,Tc)(\rho_0,T_c) points measured before and after 2.5 MeV electron irradiation for the same physical thin-film sample: solid lines for irradiated samples having measurable TcT_c, and dashed lines terminating at Tc=0.2T_c = 0.2 K for irradiated samples having TcT_c below the base temperature of our cryostat, 0.4 K. The two-point slopes suggested by this pairwise grouping of the data are remarkably consistent, despite differing “initial conditions” (i.e., differing absolute ρ0\rho_0 values); moreover, the ΔTc/Δρ0\Delta T_c/\Delta\rho_0 Cooper-pair-breaking effect induced by irradiation is at least 10 times larger in magnitude than whatever subtle trend may be discernible in the Tc(ρ0)T_c(\rho_0) behavior observed across distinct as-grown thin-film samples, which are all encircled by a red oval.

Applying this procedure reveals a striking similarity between the best-fit slopes ΔTc/Δρ0\Delta T_c/\Delta\rho_0 of the single-crystal and thin-film data sets, as depicted by the color-coded solid lines in Figure 3 and summarized in Table II. This result strongly suggests that momentum-relaxing elastic scattering from pointlike disorder plays the same microscopic role in Cooper-pair breaking in thin-film and

Sample typeΔTc/Δρ0\Delta T_c/\Delta\rho_0 (K/μΩ\mu\Omega-cm)
Single crystal [3, 5, 6]−1.15±0.11-1.15 \pm0.11
Irradiated single crystal (this work)−1.34±0.09-1.34 \pm0.09
Irradiated films (this work)−1.20±0.07-1.20 \pm0.07

Table II. Error bars on the fit coefficients are ±1σ\pm1\sigma.

single-crystal Sr2RuO4\mathrm{Sr_2RuO_4}, a conclusion which is further supported by a comparison of the TcT_c versus ρ0\rho_0 behavior observed here with previous impurity-scattering studies of bulk Sr2RuO4\mathrm{Sr_2RuO_4} single crystals [3, 4, 5, 6, 8]. Despite those studies encompassing numerous distinct realizations of “disorder”—i.e., variable densities of chemically different pointlike scattering centers, some of which couple strongly and some of which couple strongly to the charged quasiparticle excitations near the Fermi level—there is remarkable consistency across all studies when these microscopic details of the scattering processes are subsumed into their combined impact on the residual resistivity, and ρ0\rho_0 is treated as the relevant independent variable that ultimately controls the dependent variable, TcT_c.

Quantitatively determining the appropriate rigid shift between the zero points of the top and bottom axes in Figure 3 would require more information than we have obtained in these experiments, since we do not know the clean-limit Tc0T_{c0} of these thin-film samples with certainty because the films are subject to biaxial (A1gA_{1g}) and uniaxial (B1gB_{1g}) in-plane strains imparted by lattice matching to the substrate. Indeed, the simplest-possible empirical estimates, described in Appendix § 2.3, place a maximum range on Tc0T_{c0} for Sr2RuO4/NdGaO3(110)\mathrm{Sr_2RuO_4}/\mathrm{NdGaO_3}(110) of 1.4 to 2.7 K; the illustrative choice of the 0.5 μΩ\mu\Omega-cm horizontal offset employed in Figure 3 corresponds to Tc0=2.0T_{c0} = 2.0 K, and is furthermore consistent with a comparison to expectations from Abrikosov-Gor'kov pairbreaking theory (Appendix § 2.4).

Regardless of this remaining quantitative uncertainty in determining the exact Tc0T_{c0} of Sr2RuO4/NdGaO3(110)\mathrm{Sr_2RuO_4}/\mathrm{NdGaO_3}(110) on a true plot of Tc(ℏ/τpb)T_c(\hbar/\tau_{\mathrm{pb}}), the results displayed in Figure 3 offer compelling evidence that quantitatively very similar mechanisms of superconductivity are operative in epitaxial thin films and single crystals of Sr2RuO4\mathrm{Sr_2RuO_4}. We finish with a brief discussion of what insights are offered by the robust connection between TcT_c and ρ0\rho_0 revealed by this work regarding open questions surrounding the materials science and the physics of superconducting Sr2RuO4\mathrm{Sr_2RuO_4} thin films.

Although the in-plane B1gB_{1g} orthorhombic strain imparted by the NdGaO3_3(110) substrates on Sr2_2RuO4_4 likely boosts Tc0T_{c0} of these thin films slightly above that of unstrained bulk tetragonal Sr2_2RuO4_4 [19, 37], our data indicate that any strain-induced enhancement of the clean-limit pairing scale in our thin films (and concomitant symmetry-imposed anisotropies in the superconducting gaps caused by the reduction of the crystal point-group symmetry from tetragonal (D4hD_{4h}) to orthorhombic (D2hD_{2h})) are modest effects. They likely result from subtle changes in the superconducting order parameter that become irrelevant in the experimentally accessible range of quasiparticle scattering rates, because samples of either variety having as-grown TcT_cs of about 1.4 K exhibit nearly identical rates of TcT_c suppression with increasing ρ0\rho_0 when additional point-like defects are introduced via high-energy electron irradiation.

Turning this observation around, the relatively “high” TcT_cs achieved for the as-grown films, which approach the clean-limit value for bulk Sr2_2RuO4_4 of 1.50 to 1.55 K, indicate minuscule concentrations of native in-plane defects that are known to be strongly pair-breaking (for example, of order 0.01% Ru vacancies). This attests to the remarkable degree of vacancy control that has been achieved in the best Sr2_2RuO4_4 thin films, which sets a benchmark for modern oxide molecular-beam epitaxy. This result is also encouraging from a physics point of view, particularly for ongoing research efforts using Sr2_2RuO4_4 thin films to gain new perspectives on the outstanding puzzles regarding the order parameter and mechanism of the enigmatic unconventional superconductivity in this material. Finally, we note that the smooth progression from “high” to “low” TcT_cs in all cases is consistent with the presence of a sign-changing gap Δ(k)\Delta(\mathbf{k}) on all bands (likely with symmetry-enforced, non-accidental nodes) if intraband scattering dominates the pair breaking [3], or with the absence of large differences between the average magnitudes of ∣Δ(k)∣|\Delta(\mathbf{k})| on distinct bands if interband scattering dominates the pair breaking (see also Appendix § 2.4, Figure 8 & Figure 9).

Abrikosov-Gor’kov pair-breaking theory simulations

Figure 8. Abrikosov-Gor’kov pair-breaking theory simulations of Tc(ρ0)T_{\mathrm{c}}(\rho_0) for bulk Sr2_2RuO4_4. Purple square markers are data collected in this work for as-grown and electron-irradiated FIB-sculpted Sr2_2RuO4_4 single crystals, reproduced from Figure 3 of the main text. The orange curves and shaded region are simulations obtained by solving the implicit AG-like equation for TcT_{\mathrm{c}} as a function of ρ0\rho_0, varying {Tc0,ℏωpl}\{T_{\mathrm{c0}},\hbar\omega_{\mathrm{pl}}\} while keeping χ=1\chi=1 fixed; for quantitative values of the parameters employed here, see the text of Appendix D

Figure 9. Abrikosov–Gor’kov pair-breaking theory simulations of Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) for Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} thin films. Square markers are data collected in this work for as-grown and electron-irradiated 28-nm Sr2RuO4/NdGaO3(110)\mathrm{Sr}_{2}\mathrm{RuO}_{4}/\mathrm{NdGaO}_{3}(110) thin-film samples. Differently-colored sets of markers are the same underlying TcT_{\mathrm{c}} versus Δρ0,irr\Delta\rho_{0,\mathrm{irr}} data set reproduced from Figure 3 of the main text, plotted with different ad hoc rigid shifts of the horizontal axis, ρ0,offset\rho_{0,\mathrm{offset}}, as indicated in the inset legend. Solid color-coded lines are simulations obtained by solving the implicit AG-like equation for TcT_{\mathrm{c}} as a function of the Cooper-pair-breaking energy scale ℏ/τpb∝ρ0≡ρ0,offset+Δρ0,irr\hbar/\tau_{\mathrm{pb}} \propto\rho_{0} \equiv\rho_{0,\mathrm{offset}}+\Delta\rho_{0,\mathrm{irr}}, varying Tc0T_{\mathrm{c0}} while keeping both ℏωpl=1.29\hbar\omega_{\mathrm{pl}}=1.29 eV and χ=1\chi=1 fixed.

In conclusion, the results displayed in Figure 1-Figure 3 show the insights that can be gained by precisely tuning the point defect concentrations in Sr2_2RuO4_4 using high-energy electron irradiation. These experiments can be performed equally well on epitaxial thin films and single crystals of Sr2_2RuO4_4, and have the extremely high precision demonstrated here. Other methods commonly used to locate samples along a horizontal “disorder” axis, such as x-ray spectroscopy in electron microprobes [3, 38], require large sample volumes to accurately quantify dilute impurity concentrations, and would not have the sensitivity to detect such minute deviations from ideal stoichiometry. The precision available in low-volume stoichiometry techniques based on transmission electron microscopy [22, 33], Raman scattering [32], or Rutherford backscattering spectrometry, is lower still, so the high-energy electron irradiation enables investigation of a part of parameter space that cannot currently be reached by any other technique. Moreover, the ability in irradiation studies to directly compare measurements performed on the same samples, before and after irradiation, renders moot concerns about inevitable sample-specific peculiarities that could obscure the effects of the pairbreaking point disorder that we wish to study.

With a controlled and reproducible knob now available for finely adjusting the quasiparticle scattering rate and TcT_c in Sr2_2RuO4_4, it may be possible to definitively resolve some of the longstanding controversies regarding the superconductivity, such as the interpretation of heat capacity data for T<TcT<T_c [39, 40, 41] in light of other thermodynamic probes that evidence a multi-component order parameter [42, 43, 44], as well as the interpretation of signals in muon spin relaxation [45, 46, 47] and polar Kerr effect data [48], which evidence some kind of time-reversal symmetry breaking onsetting near TcT_{\mathrm{c}}. Looking forward, it will also be interesting to see what new experiments Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} thin films enable in this field; for example, performing irradiations using a collimated e−e^{-} beam inside an electron microscope [49, 50] may provide a straightforward way to spatially pattern the disorder landscape so as to create superconductor/normal-metal-all-Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} tunnel junctions for use in phase-sensitive measurements.

Data plotted in Figure 1–Figure 9 of the main text and Figure S1–Figure S5 of the Supplemental Material will be available at [51]. Additional data available upon reasonable request.

Scanning electron microscope images of samples B, C, and D

Figure S1. Scanning electron microscope images of three of the four microstructures of bulk, single-crystal Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} that were studied in this work. Sample A is shown in Figure 1(a) of the main text.

Figure S5. Determining ρ0\rho_0 and TcT_c from low-temperature resistivity data acquired for Sr2_2RuO4_4 single crystals. The data set shown here was also plotted in Figure 1(c) of the main text. (a) Entire dataset and fit to normal-state data for finding ρ0\rho_0, the residual resistivity at T=0T = 0. (b,c) Same dataset as in (a), now showing fits used to determine TcT_c, with (b) warming and (c) cooling transitions excluded for clarity.

Acknowledgments

We thank Cyrus Dreyer for useful discussions. J.P.R., H.M.L.N., E.Z., P.H.M., D.S., and A.P.M. thank the Max Planck Society for financial support. H.M.L.N. was supported by the Alexander von Humboldt Foundation Research Fellowship for Postdoctoral Researchers. N.K. is supported by JSPS KAKENHI (No. JP18K04715, No. JP21H01033, and No. JP22K19093). Research in Dresden benefits from the environment provided by the DFG Cluster of Excellence ct.qmat (EXC 2147, project ID 390858490). Electron irradiation experiments performed at the SIRIUS beamline were supported by the EMIR&A French network (FR CNRS 3618). This work was supported by the National Science Foundation Platform for the Accelerated Realization, Analysis, and Discovery of Interface Materials (PARADIM) under Cooperative Agreement No. DMR-2039380. This research was funded in part by the Gordon and Betty Moore Foundation’s EPiQS Initiative through Grant Nos. GBMF3850 and GBMF9073 to Cornell University. Sample preparation was facilitated in part by the Cornell NanoScale Facility, a member of the National Nanotechnology Coordinated Infrastructure (NNCI), which is supported by the National Science Foundation (Grant No. NNCI2025233).

J.P.R. and H.M.L.N. contributed equally to this work.

Conversions between accumulated dose and Frenkel defect density

In situ resistivity experiments

In Figure 4(a,Figure 4b), we show the resistivity ρ(D)\rho(D) measured in situ (during 2.5 MeV electron irradiations) at T=22T = 22 K as a function of accumulated e−e^{-} dose, for representative (a) FIB-sculpted single-crystal samples and (b) epitaxial thin-film samples of Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4}, respectively. Increasing DD causes monotonic, nearly-linear increases in ρ(D,22 K)\rho(D, 22\ \mathrm{K}). The best-fit lines to data collected over the range DD: [0, 0.60] C/cm2^{2} are:

Figure 4. Dependence of ρ(22 K)\rho(22\ \mathrm{K}) on irradiation dose, cross sections for creating Frenkel defects, and the effects of these defects on the residual resistivity in Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4}. (a,b) ρ(22 K)\rho(22\ \mathrm{K}) measured in situ during 2.5 MeV e−e^{-} irradiations, for a representative (a) FIB-sculpted single-crystal and (b) epitaxial thin-film sample of Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4}. (c-e) Calculated cross sections for creating vacancy-interstitial Frenkel pairs from (c) strontium, (d) ruthenium, and (e) oxygen atoms via electron irradiation. Each panel considers a range of possible displacement energies EdispE_{\mathrm{disp}} for creating each type of Frenkel pair (light to dark green color scale). (f) Data for FIB-sculpted Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} single crystals showing the experimentally measured increments in residual resistivity after accumulating variable doses of Ekin=2.5E_{\mathrm{kin}} = 2.5 MeV e−e^{-} irradiation (black markers). These data are to be compared with the expected changes in ρ0\rho_{0} that are attributable to irradiation-induced Sr vacancies (blue dashed lines), Ru vacancies (red dashed lines), and the sum of Ru + Sr vacancies (purple dashed lines), given the Frenkel pair production rates displayed in (c,d). The region between each pair of dashed lines represents how the systematic uncertainties in EdispE_{\mathrm{disp}} convert into ranges of possible Δρ0\Delta\rho_{0} versus DeffD_{\mathrm{eff}} behavior; the physically relevant parameter ranges are likely EdispE_{\mathrm{disp}} ranging from 7.5 to 15 eV for all sublattices in Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4}.

ρ(D,22 K) [μΩ-cm]={4.8+1.8⋅D [C/cm2](films)2.4+1.5⋅D [C/cm2](crystals)\rho(D, 22\ \mathrm{K})\ [\mu\Omega\text{-}\mathrm{cm}] = \begin{cases} 4.8 + 1.8 \cdot D\ [\mathrm{C}/\mathrm{cm}^{2}] & \text{(films)} \\ 2.4 + 1.5 \cdot D\ [\mathrm{C}/\mathrm{cm}^{2}] & \text{(crystals)} \end{cases}

After both samples accumulated e−e^{-} doses of 0.60 C/cm2^{2}, we thermally cycled the samples to 300 K and back to 22 K without removing the samples from the irradiation cryostat, and remeasured the resistivities indicated by the blue markers in Figure 4(a,Figure 4b). This initial “room-temperature annealing” of the irradiated samples caused ρ(22 K)\rho(22\ \mathrm{K}) to decrease from 3.3 to 3.0 μΩ\mu\Omega-cm (5.89 to 5.62 μΩ\mu\Omega-cm) for the FIB-sculpted single-crystal (thin-film) Sr2_2RuO4_4 samples, respectively, or to about 91% (95%) of the starting values. Such reductions of ρ\rho are commonly observed upon initially warming up electron-irradiated crystals, including materials that have similar solid-state chemistries to Sr2_2RuO4_4 (e.g. SrRuO3_3 [52, 53] and high-TcT_c cuprates [30, 54]), and are typically attributed to some fractions of the original concentrations of irradiation-induced defects becoming mobile at elevated temperatures. Finally, we note that due to technical difficulties with conducting in situ transport measurements during some irradiation beamtimes, the thin-film sample measured in Figure 4(b) is a resistivity bridge patterned on a 24-nm Sr2_2RuO4_4/LSAT(100) sample, rather than the 28-nm Sr2_2RuO4_4/NdGaO3_3(110) samples characterized elsewhere in the manuscript. Although this likely affects certain quantitative details of the measurements, such as the rate of resistivity increase Δρ(22 K)/ΔD\Delta\rho(22\ \mathrm{K})/\Delta D, we believe that all qualitative features of the observed ρ(D)\rho(D) behavior in Figure 4(b), including the annealing of some defects upon the first thermal cycle to 300 K, would also be observed for irradiated Sr2_2RuO4_4/NdGaO3_3(110) samples measured in situ.

Conversions between accumulated electron irradiation dose and Frenkel defect densities

We used the methods outlined in Ref. [22] to estimate the rates at which Frenkel defects (i.e., vacancy-interstitial pairs) are produced in Sr2_2RuO4_4 by high-energy electron irradiation. Creating a defect requires a certain amount of energy, known as the displacement energy EdispE_{\mathrm{disp}}, which is specific to a given atomic site and type of defect. The probability that such a defect will be formed during irradiation is given by the relativistic cross section for the transfer of E≥EdispE \ge E_{\mathrm{disp}} from an electron having kinetic energy EkinE_{\mathrm{kin}} to a nucleus of that atom. In our irradiation experiments, the probability that a high-energy electron (Ekin≈Eincident=2.5 MeVE_{\mathrm{kin}} \approx E_{\mathrm{incident}} = 2.5\ \mathrm{MeV}) interacts with any atom in the crystal is extremely low; we are operating in the “long mean free path” limit. Therefore, we calculate irradiation-induced defect concentrations for each atomic site independently, using the same global, measured irradiation dose in each case, without self-consistently accounting for energy losses and/or multiple scattering events that reduce EkinE_{\mathrm{kin}} below EincidentE_{\mathrm{incident}} as the electron beam propagates through the samples.

In Figure 4(c-Figure 4e), we plot the calculated cross sections for creating Frenkel pairs σFP\sigma_{\mathrm{FP}} on the strontium, ruthenium, and oxygen sites, respectively. The dependence of σFP\sigma_{\mathrm{FP}} on the electron kinetic energy EkinE_{\mathrm{kin}} (horizontal axis) is modeled using values for the relativistic Mott scattering cross section tabulated in the literature [22, 55, 56], and the simulations are performed considering a range of displacement energies EdispE_{\mathrm{disp}} (individual traces, green color-scale) for the formation of each type of Frenkel pair. Density-functional-based calculations of Frenkel defect energetics suggest that in Sr2_2RuO4_4, Edisp,Sr≥7.6E_{\mathrm{disp, Sr}} \ge7.6 eV and Edisp,Ru≥8.2E_{\mathrm{disp, Ru}} \ge8.2 eV (C. E. Dreyer, private communication). Meanwhile, previous electron irradiation studies of high-TcT_c copper oxides (specifically, YBa2_2Cu3_3O7−δ_{7-\delta}) that are structurally similar to Sr2_2RuO4_4 have found that Edisp,eqO=10E_{\mathrm{disp, eqO}} = 10 eV [54] or 8.4 eV [49] for creating Frenkel defects on the planar oxygen site. Accordingly, we propose that displacement energies in the range of Edisp=7.5E_{\mathrm{disp}} = 7.5 to 15 eV are the physically relevant parameter regimes for producing Frenkel defects on each of the strontium, ruthenium, and oxygen sublattices; for simplicity, we neglect any distinction between Edisp,OE_{\mathrm{disp},O} for equatorial and apical oxygen sites. Over these ranges of EdispE_{\mathrm{disp}}, the cross sections for Frenkel pair production at Ekin=2.5E_{\mathrm{kin}} = 2.5 MeV can be read off from Figure 4(c-Figure 4e) as σFP,Sr=339\sigma_{\mathrm{FP,Sr}} = 339 to 159 barn, σFP,Ru=410\sigma_{\mathrm{FP,Ru}} = 410 to 193 barn, and σFP,O=76\sigma_{\mathrm{FP,O}} = 76 to 37 barn.

Note that 1 barn = 10−2410^{-24} cm2^{2}; thus, to convert these cross sections to the number of displacements per atom (dpa) for a specific dose DD of 2.5 MeV electron irradiation, we simply need to multiply by DD given in units of [number of electrons per unit area]. It follows that Frenkel defect densities (nFPn_{\mathrm{FP}}) are produced on the unique sublattices per unit dose DD at rates of

dnFP,SrdD=(2.1 to 1.0)×10−3 dpaC/cm2  (×2 Sr/unit cell),\frac{d n_{\mathrm{FP,Sr}}}{dD} = \frac{(2.1\ \text{to}\ 1.0)\times10^{-3}\ \mathrm{dpa}}{\mathrm{C}/\mathrm{cm}^{2}}\;(\times2\ \mathrm{Sr}/\mathrm{unit\ cell}),
dnFP,RudD=(2.6 to 1.2)×10−3 dpaC/cm2  (×1 Ru/unit cell),\frac{d n_{\mathrm{FP,Ru}}}{dD} = \frac{(2.6\ \text{to}\ 1.2)\times10^{-3}\ \mathrm{dpa}}{\mathrm{C}/\mathrm{cm}^{2}}\;(\times1\ \mathrm{Ru}/\mathrm{unit\ cell}),
dnFP,OdD=(0.47 to 0.23)×10−3 dpaC/cm2  (×4 O/unit cell).\frac{d n_{\mathrm{FP,O}}}{dD} = \frac{(0.47\ \text{to}\ 0.23)\times10^{-3}\ \mathrm{dpa}}{\mathrm{C}/\mathrm{cm}^{2}}\;(\times4\ \mathrm{O}/\mathrm{unit\ cell}).

As mentioned in the main text, direct visualization of such dilute point-like defect concentrations, nFP≲O(0.1%)n_{\mathrm{FP}} \lesssim O(0.1\%) = one part per thousand, is a formidable challenge, well beyond the current capabilities of state-of-the-art microstructural probes such as scanning transmission electron microscopy [22, 33]. Nonetheless, by making a few more assumptions, it is possible to indirectly confirm the general consistency of these estimated defect densities by relating nFPn_{\mathrm{FP}} to one of the observables measured in our current study—namely, the residual resistivity in the absence of superconductivity, ρ0≡ρns(T→0 K)\rho_0 \equiv\rho_{ns}(T \to0\ \mathrm{K}).

In Figure 2(a) of the main text, we displayed the results of ex situ measurements of the irradiation-induced increment in residual resistivity Δρ0\Delta\rho_0 for four distinct FIB-sculpted single crystals of Sr2_2RuO4_4 that accumulated variable doses DD of 2.5 MeV e−e^- irradiation. As discussed above, some fraction of the defects created by irradiation are lost when a sample is first warmed to room temperature following irradiation. We model this loss as a simple multiplicative reduction of the dose received by each sample, calculating the reduction factor using the 22 K in-situ data [red points in Figure 4(a)] and the resistivity measured at 22 K after thermally cycling the sample to room temperature and back [blue point in Figure 4(a)]. In Figure 4(f), we re-plot the data points from Figure 2(a) of the main text versus the effective irradiation dose received, Deff=0.62×DD_{\mathrm{eff}} = 0.62 \times D, where 0.62 is the calculated reduction factor. We used the reduction factor determined from sample C for all four samples because most of the other samples had incomplete in situ resistivity datasets. Although this adjustment procedure implicitly appeals to Matthiessen’s-Rule-type reasoning, which is known to not be strictly valid in perovskite-based ruthenates [14, 52], the errors associated with this approximation are small compared with other systematic uncertainties in these estimates of nFPn_{\mathrm{FP}} and in how efficiently the equilibrium nFPn_{\mathrm{FP}} for Sr, Ru, and O are transduced into corresponding increases in ρ0\rho_0.

Previous studies of Sr2_2RuO4_4 single crystals that were intentionally doped with chemical impurities on the Ru site, namely, Sr2_2Ru1−x_{1-x}(Ti, Ir)x_xO4_4, demonstrated that such defects act as nearly unitary-limit scatterers that increase the residual resistivity at a rate of dρ0/dx≈425d\rho_0/dx \approx425 μΩ\mu\Omega-cm, where xx is the fractional dopant density per unit cell [4, 5]. Likewise, previous studies of Sr2_2RuO4_4 single crystals that were intentionally doped with chemical impurities on the Sr site, namely, Sr2−y_{2-y}Lay_yRuO4_4, demonstrated that such defects act as nearly Born-limit scatterers that increase the residual resistivity at a much smaller rate of dρ0/dy≈40d\rho_0/dy \approx40 μΩ\mu\Omega-cm, where yy is the fractional dopant density per unit cell [6]. Assuming that Sr and Ru vacancies scatter the charge-carrying quasiparticles in an identical fashion to chemically substituted impurities on the respective atomic sites, we can then multiply the above estimates of dnFP,Sr/dDdn_{\mathrm{FP,Sr}}/dD (dnFP,Ru/dDdn_{\mathrm{FP,Ru}}/dD) by the empirical value of dρ0/dyd\rho_0/dy (dρ0/dxd\rho_0/dx) to obtain:

dρ0dD=(0.17 to 0.079) μΩ-cmC/cm2(from Sr vacancies)\frac{d\rho_0}{dD} = \frac{(0.17\ \text{to}\ 0.079)\ \mu\Omega\text{-cm}}{\text{C}/\text{cm}^2} \quad\text{(from Sr vacancies)}
dρ0dD=(1.1 to 0.51) μΩ-cmC/cm2(from Ru vacancies)\frac{d\rho_0}{dD} = \frac{(1.1\ \text{to}\ 0.51)\ \mu\Omega\text{-cm}}{\text{C}/\text{cm}^2} \quad\text{(from Ru vacancies)}
dρ0dD=(1.3 to 0.59) μΩ-cmC/cm2(summed total)\frac{d\rho_0}{dD} = \frac{(1.3\ \text{to}\ 0.59)\ \mu\Omega\text{-cm}}{\text{C}/\text{cm}^2} \quad\text{(summed total)}

These simulated rates of residual resistivity increase per unit of 2.5 MeV e−e^- irradiation dose are drawn as dashed lines in Figure 4(f). The experimentally measured Δρ0\Delta\rho_0 versus DeffD_{\mathrm{eff}} data points for FIB-sculpted single crystals of Sr2_2RuO4_4 agree reasonably well with these simulations, which suggests that the estimated cross sections for Frenkel defect production are realistic. We note that in arriving at these simulated rates of dρ0/dDd\rho_0/dD, we neglected any possible contributions of Ru and Sr interstitials to increases in ρ0\rho_0, and we ignored entirely all irradiation-induced defects on the O site. Although these choices were made out of convenience—namely, because there are not any available data in the literature to indicate how much such defects might contribute to ρ0\rho_0 in Sr2_2RuO4_4—Figure 4(f) indicates that considering these additional types of irradiation-induced disorder is not strictly necessary to account for the experimentally observed rate dρ0/dDd\rho_0/dD.

It remains an open question to determine whether the apparent level of agreement between simulation and experiment in Figure 4(f) is somewhat artificial, in the sense that the true displacement energies for Sr and Ru are actually towards the higher end of our estimated range (15 eV) and that the contributions of interstitials and oxygen defects to Δρ0\Delta\rho_0 are not negligible, or whether it is suggestive that the effects on Δρ0\Delta\rho_0 of the explicitly neglected defects are already implicitly accounted for by the Deff→DD_{\mathrm{eff}} \to D “room-temperature annealing” conversion of the experimental data. Along these lines, we note that the extent to which Frenkel defects on the oxygen sites affect the resistivity and superconductivity in Sr2_2RuO4_4 might be addressable in a more direct fashion in future irradiation studies that utilize lower incident electron kinetic energies, which would transfer sufficient energy to create defects on the O sublattices, but not to create defects on the Sr or Ru sites (cf. the low Ekin≲0.5E_{\mathrm{kin}} \lesssim0.5 MeV regions of Figure 4(c–Figure 4e)); a similar approach has been employed previously for high-TcT_c cuprates [49].

Magnetoresistance of thin films

Superconducting upper critical field

In Figure 5, we show that a moderate e−e^- dose (D=0.45D = 0.45 C/cm2^2) of 2.5 MeV electron irradiation substantially reduces the upper critical magnetic fields required to suppress superconductivity in thin-film Sr2_2RuO4_4. For these electrical transport measurements, the external magnetic field is directed along the crystallographic cc-axis of Sr2_2RuO4_4, which is also the out-of-plane direction of epitaxial thin-film samples studied here [see inset to Figure 5(c)]. Thus, the critical field probed is Hc⊥H_{c\perp} in the terminology of Refs. [57, 58], which is essentially equivalent to Hc2H_{c2} (with H∥cH \parallel c) for a bulk specimen of a type-II superconductor such as Sr2_2RuO4_4. Hereafter we refer to Hc⊥H_{c\perp} and Hc2∥cH_{c2\parallel c} interchangeably.

Figure 5. Effect of electron irradiation on the superconducting upper critical fields of Sr2_2RuO4_4 thin films. (a) Normalized resistivity versus temperature data for an as-grown Sr2_2RuO4_4 thin-film resistivity bridge, acquired at external magnetic fields ranging from 0 to 1.1 kOe in discrete steps of 0.1 kOe. (b) Same measurements as in panel (a), but after the sample had received a 0.45 C/cm2^2 dose of 2.5 MeV electron irradiation. Note that the external magnetic field steps in (b) are half of those displayed in (a), and that the maximum applied field is now merely 0.4 kOe, which is sufficient to suppress TcT_\mathrm{c} to substantially below the base temperature of the helium-3 cryostat, ≈0.4\approx0.4 K. Currents of 1 μ\muA, rather than the usual 10 μ\muA, were used in the acquisition of the data shown in (a,b). (c) Upper critical magnetic fields for superconductivity (Hc⊥H_\mathrm{c\perp}), before and after irradiation, extracted from the resistivity data in panels (a,b), along with linear fits (grey solid lines) used for estimating Hc⊥(T→0)H_\mathrm{c\perp}(T \to0). The inset schematically depicts the measurement geometry and orientation of HH with respect to the Sr2_2RuO4_4 crystal structure. Solid markers indicate the TcT_\mathrm{c}s where ρ(T,H)\rho(T,H) crosses the 50% threshold of ρ(2 K,0 kOe)\rho(2\ \mathrm{K}, 0\ \mathrm{kOe}) [bold dashed line in (a,b)], and the horizontal error bars on these TcT_\mathrm{c}s represent where ρ(T,H)\rho(T,H) crosses the 10% and 80% thresholds of ρ(2 K,0 kOe)\rho(2\ \mathrm{K}, 0\ \mathrm{kOe}) [dashed lines in (a,b)].

The simultaneous decreases of both TcT_c and Hc2∥cH_{c2\parallel c} upon high-energy electron irradiation provides further evidence that the irradiation-induced defects are point-like scattering centers that uniformly suppress the characteristic intra-granular condensation energy scale of the superconductivity in Sr2_2RuO4_4. By contrast, if the electron irradiation created columnar and/or other types of extended defects, we would generally expect Hc2∥cH_{c2\parallel c} to remain unchanged, or perhaps even to be enhanced, due to increased pinning of vortices at the extended defects, while properties that depend on the details of the inter-granular Josephson network of superconducting grains [30], such as critical currents, would change.

Without a clear understanding of the effective pairing interactions that cause superconductivity to emerge in Sr2_2RuO4_4, it is difficult to quantitatively interpret the observed magnitudes of TcT_\mathrm{c} and Hc2∥cH_{\mathrm{c2}\parallel c} reduction upon irradiation, since both of these quantities depend on some appropriately weighted averages of the superconducting order parameter over the quasiparticle states near the Fermi level EFE_\mathrm{F}. Nevertheless, making the standard assumption that Hc2∥cH_{\mathrm{c2}\parallel c} is orbitally limited, we can convert the measured upper critical fields into phenomenological in-plane superconducting coherence lengths (ξab\xi_{ab}) using the Ginzburg–Landau relation:

μ0Hc2∥c=ϕ02πξab2⟹ξab [A˚]=329106Hc2∥c [kOe]\mu_0 H_{\mathrm{c2}\parallel c} = \frac{\phi_0}{2\pi\xi_{ab}^{2}} \quad\Longrightarrow\quad\xi_{ab}\,[\text{\AA}] = \sqrt{\frac{329106}{H_{\mathrm{c2}\parallel c}\,[\mathrm{kOe}]}}

where ϕ0=h/(2e)\phi_0 = h/(2e) is the superconducting flux quantum.

To account for the temperature dependence of the quantities in this expression, we follow previous studies of epitaxial thin films of Sr2_2RuO4_4, which have shown that the nearly linear scaling of Hc⊥H_{\mathrm{c\perp}} versus TcT_\mathrm{c}—observed in Figure 5 for TT down to 0.4 K, i.e., down to T/Tc=0.3T/T_\mathrm{c} = 0.3 for the as-grown sample—in fact persists over at least another decade in TT, down to the lowest temperatures accessible in a dilution refrigerator, O[0.06 K]\mathcal{O}[0.06\ \mathrm{K}] [59]. Accordingly, we fit all available Hc⊥H_{\mathrm{c\perp}} versus TcT_\mathrm{c} data points for the as-grown and irradiated 28-nm Sr2_2RuO4_4/NdGaO3_3(110) samples to separate lines, and then extrapolate the fit results to zero temperature, as shown by the gray lines in Figure 5(c), to obtain ξab(T→0 K)=500±20\xi_{ab}(T \to0\ \mathrm{K}) = 500 \pm20 Å for as-grown films, and 790 ±\pm 30 Å after a dose of 0.45 C/cm2^2.

The error bars quoted here on ξab\xi_{ab} refer to the spread of Hc⊥(T→0 K)H_{\mathrm{c\perp}}(T \to0\ \mathrm{K}) values obtained by employing 10% or 80% thresholds of ρ(2 K,0 kOe)\rho(2\ \mathrm{K}, 0\ \mathrm{kOe}) to define TcT_\mathrm{c}, rather than a 50% threshold, and propagating these systematic uncertainties through the linear fits and extrapolations of the measured Hc⊥(Tc)H_{\mathrm{c\perp}}(T_\mathrm{c}) phase boundary [cf. gray-shaded regions in Figure 5(c)]. While the sensitivity of ρ(T,H)\rho(T,H) to percolating, but otherwise filamentary, superconducting pathways implies that electrical transport measurements inherently tend to overestimate upper critical fields compared with bulk-sensitive measurements of superconductivity [57, 60], such considerations only affect the absolute values of Hc2H_{\mathrm{c2}} that are sensed by different probes; by contrast, the relative change observed here in Sr2_2RuO4_4 upon electron irradiation is unambiguous: increasing the disorder scattering rate suppresses Hc2∥cH_{\mathrm{c2}\parallel c} (enhances ξab\xi_{ab}). This result is qualitatively consistent with previous studies of Sr2_2RuO4_4 that deduced such a correlation by analyzing Hc2∥cH_{\mathrm{c2}\parallel c} data across a collection of different as-grown samples, in both bulk [8] and thin-film form [59].

Effect of electron irradiation on Shubnikov-de Haas oscillations

To place the irradiation-induced modifications to ρ0\rho_0, TcT_c, and Hc2∥cH_{c2\parallel c} in proper context, it is important to note that certain features of the normal-state near-EFE_{\rm F} electronic structure in Sr2_2RuO4_4, such as the sizes and shapes of the Fermi surfaces, are not appreciably affected by the doses of high-energy electron irradiation administered in this work. To investigate the Fermiology in detail, in Figure 6 we plot low-temperature magnetotransport data acquired for an as-grown 28-nm Sr2_2RuO4_4/NdGaO3_3(110) sample, and for the same sample after accumulating a moderate e−e^- dose (D=0.60D = 0.60 C/cm2^2) of 2.5 MeV electron irradiation. The external magnetic field is again directed out-of-plane, along the crystallographic cc axis of Sr2_2RuO4_4, and the temperature is held constant at a nominal value of T=0.45T = 0.45 K. We used rms excitation currents of I=100I = 100 μ\muA for transport measurements performed during these field sweeps, to further enhance the signal-to-noise ratio.

Figure 6. Effect of electron irradiation on the magnetoresistance of Sr2_2RuO4_4. (a) Normalized magnetoresistance (MR) plotted versus the externally applied magnetic field for an as-grown Sr2_2RuO4_4 thin-film resistivity bridge (blue), and the same sample after receiving a 0.60 C/cm2^2 dose of 2.5 MeV electron irradiation (teal). Here we define MR [%] ≡100×[ρ(H)−ρ(0)]/ρ(0)\equiv100 \times[\rho(H)-\rho(0)]/\rho(0), where ρ(0)\rho(0) is the extrapolated resistivity as H→0H \to0 in the absence of superconductivity. Currents of 100 μ\muA, rather than the usual 10 μ\muA, were used in the acquisition of the data shown in this figure. (b,c) Zoomed-in views of the resistivity measured over the high-field range indicated by the dashed box in panel (a), after subtracting and normalizing to empirically determined quadratic polynomial backgrounds ρbg(H)\rho_{\rm bg}(H) for both data sets: ρ~/ρ0≡[ρ(H)−ρbg(H)]/ρbg(H)\tilde{\rho}/\rho_0 \equiv[\rho(H)-\rho_{\rm bg}(H)]/\rho_{\rm bg}(H). Superimposed on these slowly and smoothly varying backgrounds are rapidly oscillating Shubnikov-de Haas contributions to the magnetoresistance, that are periodic in inverse field and have dominant frequencies FαF_\alpha characteristic of charge carriers completing phase-coherent cyclotron motion around the α\alpha-sheet Fermi surface of Sr2_2RuO4_4 [cf. upper left inset to panel (a)].

The overall magnitude of the normalized magnetoresistance (MR) in the normal state (i.e., for B=μ0H≫μ0Hc⊥B = \mu_0 H \gg\mu_0 H_{c\perp}) is somewhat reduced upon increasing DD [Figure 6(a)]. This behavior is generically expected whenever more than one decay rate enters the charge-carrier momentum relaxation dynamics (see, e.g., Ref. [22] and references contained therein), and indeed time-domain THz spectroscopy measurements on these Sr2_2RuO4_4 epitaxial thin films have directly shown that the low-energy optical conductivity at low temperatures contains contributions from more than one Drude-like oscillator [14]. Although detailed accounts of how electron irradiation couples to the multiple transport lifetimes that determine the dc MR (as well as the ac σ(ω)\sigma(\omega) for small ω≠0\omega\ne0) are beyond the scope of the present work, there is another feature of the data that is simpler to interpret quantitatively: namely, rapidly oscillating Shubnikov-de Haas (SdH) contributions to the MR.

To better isolate and visualize the SdH signal, we fit the raw MR data within the 12 to 14 Tesla field range [dashed box in Figure 6(a)] to the locally quadratic form ρbg(H)=A0+A1H+A2H2\rho_{\rm bg}(H) = A_0 + A_1 H + A_2 H^2, and then compute the background-subtracted and background-normalized MR, ρ~/ρ0=[ρ(H)−ρbg(H)]/ρbg(H)\tilde{\rho}/\rho_0 = [\rho(H)-\rho_{\rm bg}(H)]/\rho_{\rm bg}(H). We plot the results thus obtained for ρ~/ρ0\tilde{\rho}/\rho_0 for the as-grown and electron-irradiated Sr2_2RuO4_4 samples in panels (b) and (c) of Figure 6, respectively. Both ρ~/ρ0\tilde{\rho}/\rho_0 traces clearly exhibit SdH oscillations that are periodic in inverse field.

The dominant oscillation frequency in the data collected at the temperatures and shown here is FαF_\alpha, which results from charge carriers completing phase-coherent cyclotron orbits around the α\alpha-Fermi surface of Sr2_2RuO4_4. Counting peaks and troughs in Figure 6(b,Figure 6c), we measure N=37N = 37 complete oscillation periods over the field range μ0H=11.880\mu_0 H = 11.880 to 13.964 Tesla for both the as-grown and the electron-irradiated samples, corresponding to oscillation frequencies of Fα=N/(1/11.880 T−1/13.964 T)=2945±20F_\alpha= N/(1/11.880\ {\rm T}^{-1}/13.964\ {\rm T}) = 2945 \pm20 Tesla for both samples. In other words, moderate e−e^- doses do not modify FαF_\alpha, within the experimental resolution of approximately 1%. We estimate the systematic error bars quoted here on FαF_\alpha by our ability to detect ±1/4\pm1/4 of an additional period of the α\alpha-sheet-derived SdH signal over the (inverse) magnetic field range probed in Figure 6(b,Figure 6c).

In the inset to Figure 6(a), we schematically sketch the well-known {α,β,γ}\{\alpha,\beta,\gamma\} Fermi surfaces of Sr2_2RuO4_4, projected onto the two-dimensional first Brillouin zone, which is bounded by solid black lines. The area AkA_k enclosed by each Fermi surface in k-space follows directly from the corresponding primary quantum oscillation frequency FiF_i (i∈{α,β,γ}i \in\{\alpha,\beta,\gamma\}), according to the Onsager relation Ak,i=(2πe/ℏ)FiA_{k,i} = (2\pi e/\hbar)F_i. Therefore, the invariance of FαF_\alpha noted above implies that electron irradiation does not alter the k-space area enclosed by the α\alpha-sheet Fermi surface, i.e., the gray-shaded region drawn in the inset to Figure 6(a). Invoking Luttinger’s theorem, this observation also implies that moderate doses of electron irradiation do not alter the itinerant carrier density in Sr2_2RuO4_4.

Estimating clean-limit Tc0T_{c0} for thin films

In the discussion surrounding Figure 3 of the main text, we noted that in Sr2_2RuO4_4 thin films, TcT_c responds sensitively to relative changes in the residual resistivity induced by electron irradiation, Δρ0,irr\Delta\rho_{0,\mathrm{irr}}, yet TcT_c appears to depend much less regularly on ρ0\rho_0 when all residual resistivities for as-grown and irradiated thin-film samples are plotted in absolute units. Figure 7 illustrates both of these observations graphically. All 18 (ρ0,Tc)(\rho_0,T_c) red square markers for Sr2_2RuO4_4 thin films plotted in Figure 7 are extracted in absolute units from the corresponding ρ(T)\rho(T) data traces plotted in Figure S4 of the Supplemental Material [24]. To serve as side-by-side references, the same (ρ0,Tc)(\rho_0,T_c) gray points and purple squares for Sr2_2RuO4_4 bulk single crystals from Figure 3 of the main text are also included in Figure 7.

Figure S4. Figure S4. Electrical resistivity versus temperature of Sr2RuO4\mathrm{Sr_2RuO_4} thin films, before and after irradiation. Panels (a-f) are sorted from top to bottom in order of increasing dose of 2.5 MeV e−e^{-} irradiation, ranging from (a) 0.20 C/cm20.20\ \mathrm{C/cm^2} to (f) 1.00 C/cm21.00\ \mathrm{C/cm^2}. The vertical and horizontal scales of all graphs are identical, to facilitate visualization of e−e^{-}-dose-dependent changes in ρ\rho and TcT_\mathrm{c}. Gray arrows within each panel are guides to the eye, schematically indicating the irradiation-induced changes in ρ0\rho_0 and TcT_\mathrm{c} for each sample.

Viewed merely as a collection of independent points, the TcT_c versus ρ0\rho_0 behavior of the thin-film data in Figure 7 appears rather scattered, and it is difficult to establish any clear correlation between these two variables. By contrast, when one draws lines between each pair of (ρ0,Tc)(\rho_0,T_c) points that correspond to the same physical sample, measured before and after irradiation, visual inspection of the solid lines in Figure 7 reveals that electron irradiation has very similar, proportional effects on ΔTc\Delta T_c and Δρ0,irr\Delta\rho_{0,\mathrm{irr}} across all distinct Sr2_2RuO4_4 thin-film samples. Furthermore, as emphasized in the main text, collecting these independent measurements of ΔTc/Δρ0\Delta T_c/\Delta\rho_0 into a single number for the rate of TcT_c suppression with increasing quasiparticle scattering rate results in a number that is quantitatively very similar between these electron-irradiated Sr2_2RuO4_4 thin-film samples and single-crystal Sr2_2RuO4_4 samples containing various types of defects (Table II).

In Figure 3 of the main text, we proposed that the most natural interpretation and framing of the raw Tc(ρ0)T_c(\rho_0) data for thin films can be summarized as follows: (i.) the quantitative similarity of TcT_c across all as-grown thin-film samples (1.35 to 1.41 K) implies that their ℏ/τpb\hbar/\tau_{\mathrm{pb}} values are nearly identical; (ii.) based on the detailed comparisons between Sr2_2RuO4_4 thin films and single crystals presented in the main text, using electron irradiation is a valid way to produce pure (quasi-elastic and quasi-isotropic) Cooper-pair-breaking scattering, and thereby suppress TcT_c at an initial rate of ≈ 1.2 K/μΩ\mu\Omega-cm; thus, (iii.) the remaining outstanding question is to determine the relative rigid offset ρ0,offset\rho_{0,\mathrm{offset}} of these as-grown thin-film samples relative to the zero point of an appropriately-defined ℏ/τpb\hbar/\tau_{\mathrm{pb}} Cooper-pair-breaking energy scale. Equivalently, since our electron irradiation studies have now precisely established the magnitude of TcT_c suppression for a given change in ρ0\rho_0 that also proportionally increments ℏ/τpb\hbar/\tau_{\mathrm{pb}}, determining ρ0,offset\rho_{0,\mathrm{offset}} requires knowledge of the clean-limit Tc0≡Tc(ℏ/τpb→0)T_{c0} \equiv T_c(\hbar/\tau_{\mathrm{pb}} \to0) of Sr2_2RuO4_4/NdGaO3_3(110).

At present, the simplest-possible empirical estimates constrain ρ0,offset\rho_{0,\mathrm{offset}} to be within the following extreme limits: (i.) ρ0,offset=0\rho_{0,\mathrm{offset}} = 0, in which case none of the experimentally-measured ρ0\rho_0 in as-grown thin-film samples actually contributes to ℏ/τpb\hbar/\tau_{\mathrm{pb}} (i.e., Tc0T_{c0} of Sr2_2RuO4_4/NdGaO3_3(110) is equal to the values measured in this work on as-grown samples, ≈ 1.4 K), and (ii.) ρ0,offset=1.1\rho_{0,\mathrm{offset}} = 1.1 μΩ\mu\Omega-cm, which is equal to the experimentally-measured ρ0\rho_0 for as-grown Tc≈1.4T_{\mathrm{c}} \approx1.4 K thin-film samples exhibiting the lowest absolute ρ0\rho_0s in the present work [24]. In this case, the hypothetical Tc0T_{\mathrm{c0}} of Sr2_2RuO4_4/NdGaO3_3(110) would equal 1.4 K + (1.1 μΩ\mu\Omega-cm ×\times 1.2 K/μΩ\mu\Omega-cm) ≈2.7\approx2.7 K. In Figure 3 of the main text, we arbitrarily chose a rigid shift of the top axis by ρ0,offset=0.5\rho_{0,\mathrm{offset}} = 0.5 μΩ\mu\Omega-cm relative to the bottom axis, about halfway between these two extremes, corresponding to a Sr2_2RuO4_4/NdGaO3_3(110) Tc0≈2.0T_{\mathrm{c0}} \approx2.0 K.

Based on the method proposed here of interpreting the thin-film data, it would be possible to further narrow down the range of potential Tc0T_{\mathrm{c0}} values for Sr2_2RuO4_4/NdGaO3_3(110) in the future either by synthesizing such Sr2_2RuO4_4 thin-film samples with appreciably higher as-grown Tc>1.4T_{\mathrm{c}} > 1.4 K, or by maintaining “high” Tc≈1.4T_{\mathrm{c}} \approx1.4 K in as-grown samples with appreciably lower as-grown ρ0<1\rho_0 < 1 μΩ\mu\Omega-cm. While some limited evidence for the former exists in the literature, e.g. Ref. [19] reported a broad (about 0.4 K-wide) resistively-measured superconducting transition centered at a midpoint Tc=1.8T_{\mathrm{c}} = 1.8 K in a 55-nm-thick Sr2_2RuO4_4/NdGaO3_3(110) sample, to the best of our knowledge, there are no examples in the literature of Sr2_2RuO4_4 thin-film samples synthesized on any perovskite-based substrate that exhibit the latter property. The latter observation suggests that the levels of ρ0\rho_0 currently achieved are pushing up against a fundamental length scale for charge-carrier momentum-relaxing scattering from extended structural defects in heteroepitaxial thin film/substrate material platforms [10].

Comparison to Abrikosov-Gor’kov theory

In Figure 8, we show that the results of our electron irradiation experiments on FIB-sculpted bulk single crystals of Sr2_2RuO4_4 can be described well by theoretical Tc(ρ0)T_{\mathrm{c}}(\rho_0) curves calculated according to the standard Abrikosov-Gor’kov (AG) Cooper-pair-breaking theory of TcT_{\mathrm{c}} suppression [61], applied to the case of non-magnetic point-defect scattering in an effectively single-band unconventional superconductor [62, 63, 64, 65, 66].

In such theories, TcT_{\mathrm{c}} is found by solving an implicit equation of the general form (see, e.g., Eqn. 16 of Ref. [63] or Eqn. 35 of Ref. [66]):

ln⁡(Tc0Tc)=χ[Ψ(12+ℏ/τ4πkBTc)−Ψ(12)](1)\ln\left(\frac{T_{\mathrm{c0}}}{T_{\mathrm{c}}}\right)=\chi\left[\Psi\left(\frac{1}{2}+\frac{\hbar/\tau}{4\pi k_{\mathrm{B}}T_{\mathrm{c}}}\right)-\Psi\left(\frac{1}{2}\right)\right] \tag*{(1)}

where Ψ\Psi is the digamma function, ℏ\hbar is Planck’s constant, 1/τ1/\tau is the quasiparticle scattering rate, kBk_{\mathrm{B}} is Boltzmann’s constant, Tc0T_{\mathrm{c0}} is the so-called “clean-limit” superconducting transition temperature in the disorder-free limit ℏ/τ→0\hbar/\tau\to0, and

χ=1−⟨Δ(k)⟩FS2⟨Δ2(k)⟩FS(2)\chi= 1-\frac{\langle\Delta(\mathbf{k})\rangle_{\mathrm{FS}}^{2}}{\langle\Delta^{2}(\mathbf{k})\rangle_{\mathrm{FS}}} \tag*{(2)}

is a constant that describes the anisotropy of the superconducting order parameter (SCOP), ⟨\langleaveraged⟩\rangle over the Fermi surface (FS). For specific limiting examples of the latter, a purely sign-changing (e.g., “dd-wave”) SCOP that averages to zero over the Brillouin zone (⟨Δ(k)⟩=0\langle\Delta(\mathbf{k})\rangle=0) has χ=1\chi=1, whereas a purely uniform/isotropic (Δ(k)=\Delta(\mathbf{k})= constant, “ss-wave”) SCOP has χ=0\chi=0.

Although more complicated relationships are often observed in real materials, in theory the single-particle scattering rate that parameterizes the Cooper-pair-breaking energy scale in Eq. (1) is typically assumed to be directly proportional to the experimentally measured planar residual resistivity ρ0\rho_0, 1/τ=ρ0(ωpl2/4π)1/\tau=\rho_0(\omega_{\mathrm{pl}}^2/4\pi), where ℏωpl\hbar\omega_{\mathrm{pl}} is a suitably averaged characteristic plasma frequency describing in-plane motion of the charge carriers [64, 66].

The quantitative parameters that describe the range of theoretical Tc(ρ0)T_{\mathrm{c}}(\rho_0) curves for bulk Sr2_2RuO4_4 drawn in Figure 8 are χ=1\chi=1, Tc0=1.50T_{\mathrm{c0}}=1.50 K to 1.60 K, and ℏωpl=1.40\hbar\omega_{\mathrm{pl}}=1.40 eV to 1.34 eV. Taken together, these parameter choices determine critical scattering rates ρ0crit=0.86\rho_0^{\mathrm{crit}}=0.86 μΩ\mu\Omega-cm to 1.00 μΩ\mu\Omega-cm. For ρ0>ρ0crit\rho_0 > \rho_0^{\mathrm{crit}}, only the trivial solution Tc=0T_{\mathrm{c}}=0 exists to the above AG-like equation with χ=1\chi=1.

We consider the agreement observed here between theory and experiment to be essentially phenomenological in nature; there are too many outstanding unknowns about the superconductivity of Sr2_2RuO4_4 for this type of effective description to be interpreted too literally. In the regime of “small” ρ0≪ρ0crit\rho_0 \ll\rho_0^{\mathrm{crit}} where many of the experimental (ρ0,Tc)(\rho_0,T_{\mathrm{c}}) data points we have collected exist, there are redundant dependencies of the initial rate of TcT_{\mathrm{c}} suppression [62, 63, 65, 66], both in how increases in

ρ0\rho_{0} transduce into increases in ℏ/τ\hbar/\tau (i.e., on the effective ωpl\omega_{\mathrm{pl}}) [64, 66], and in how the fully k-resolved SCOP of a multi-orbital system such as Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} reduces to an effectively single-band SCOP anisotropy χ\chi [67, 68]. Nevertheless, while the solutions presented here are by no means uniquely determined, the overall phenomenological Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) curves shown in Figure 8 may still prove useful as initial guesses for modeling strain-induced changes to Tc0T_{\mathrm{c0}} across different thin-film variants of Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4}, as discussed in more detail below.

In principle, the systematic deviations from purely linear Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) behavior expected in AG pair-breaking theory should allow one to infer the proximity of a given set of (ρ0,Tc)(\rho_{0},T_{\mathrm{c}}) data points to the critical ρ0crit.\rho_{0}^{\mathrm{crit.}} at which superconductivity is suppressed completely. This method of discerning ρ0crit.\rho_{0}^{\mathrm{crit.}} in turn allows for an absolute determination of Tc0T_{\mathrm{c0}}, because increases in Tc0T_{\mathrm{c0}} cause linear increases in ρ0crit.\rho_{0}^{\mathrm{crit.}} in simple Cooper-pair-breaking theories that are effectively single-band, with one dominant superconducting pairing scale, ∣Δmax⁡∣|\Delta_{\max}|.

To apply this type of reasoning to our Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} thin-film electron-irradiation data, we started with a phenomenological AG-like Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) curve similar to those that describe well the (ρ0,Tc)(\rho_{0},T_{\mathrm{c}}) data points we collected for electron-irradiated Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} FIB-sculpted single crystals in this work, Figure 8. To optimize the general agreement of these calculated Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) curves with the experimental thin-film (ρ0,Tc)(\rho_{0},T_{\mathrm{c}}) data points, we adjusted the effective plasma frequency ℏωpl=1.37\hbar\omega_{\mathrm{pl}}=1.37 eV used for the bulk Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} AG simulations in Figure 8 to ℏωpl=1.29\hbar\omega_{\mathrm{pl}}=1.29 eV for the thin-film AG simulations in Figure 9. The effective SCOP anisotropy χ=1\chi=1 was held at the same fixed value as in the case of bulk samples, although as we stressed earlier, within AG-like pair-breaking theories there are redundant dependencies of the calculated Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) behavior on (χ,ωpl)(\chi,\omega_{\mathrm{pl}}), so other solutions would be possible that would fit the existing data equally well. Finally, we assumed that any epitaxial-strain-induced increase (or decrease) in Tc0T_{\mathrm{c0}} for Sr2RuO4/NdGaO3(110)\mathrm{Sr}_{2}\mathrm{RuO}_{4}/\mathrm{NdGaO}_{3}(110) relative to the Tc0T_{\mathrm{c0}} of bulk Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} results from a k\mathbf{k}-independent multi-plicative enhancement (or suppression) of ∣Δ(k)∣|\Delta(\mathbf{k})|, along with negligible strain-dependent changes in the Fermi surface (cf. Figure 6). Under this assumption, we uniformly scaled up (or down) the phenomenological AG-like Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) curve based on various hypothetical Tc0T_{\mathrm{c0}} values, keeping ℏωpl=1.29\hbar\omega_{\mathrm{pl}}=1.29 eV constant, to produce simulated Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) curves against which to compare the Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} thin-film (ρ0,Tc)(\rho_{0},T_{\mathrm{c}}) data points.

Figure 9 illustrates the results of this type of analysis. For hypothetical Tc0T_{\mathrm{c0}} curves towards the high end of our allowed range of Tc0T_{\mathrm{c0}}, e.g., for the blue simulated curve with Tc0=2.6T_{\mathrm{c0}}=2.6 K (ρ0crit.=1.77\rho_{0}^{\mathrm{crit.}}=1.77 μΩ\mu\Omega-cm), the two irradiated thin-film samples with Tc=0.63T_{\mathrm{c}}=0.63 K and 0.680.68 K (which both received a 2.5 MeV e−^{-} dose of 0.60.6 C/cm2^{2}) would be small enough fractions of Tc0T_{\mathrm{c0}} (i.e., Tc/Tc0<0.3T_{\mathrm{c}}/T_{\mathrm{c0}}<0.3) that they would be well within the range of a given AG-like pair-breaking-theory curve where non-linearities in the Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) behavior would become obvious. The absence of any such non-linear features in the experimental data suggests that Tc0T_{\mathrm{c0}} for Sr2RuO4/NdGaO3(110)\mathrm{Sr}_{2}\mathrm{RuO}_{4}/\mathrm{NdGaO}_{3}(110) is likely less than 2.2 K, provided that our assumption of χ≈1\chi\approx1 is, in fact, realized.

On the other hand, the red simulated Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) curve having Tc0=2.0T_{\mathrm{c0}}=2.0 K (which combined with {χ=1, ℏωpl=1.29 eV}\{\chi=1,\ \hbar\omega_{\mathrm{pl}}=1.29\ \mathrm{eV}\} results in ρ0crit.=1.36\rho_{0}^{\mathrm{crit.}}=1.36 μΩ\mu\Omega-cm) matches the red experimental data squares (plotted with an ad hoc ρ0,offset=0.57\rho_{0,\mathrm{offset}}=0.57 μΩ\mu\Omega-cm) quite well. The purple simulated Tc(ρ0)T_{\mathrm{c}}(\rho_{0}) curve having Tc0=1.4T_{\mathrm{c0}}=1.4 K (ρ0crit.=0.95\rho_{0}^{\mathrm{crit.}}=0.95 μΩ\mu\Omega-cm) matches the purple experimental data squares (plotted with a much reduced ad hoc ρ0,offset=0.02\rho_{0,\mathrm{offset}}=0.02 μΩ\mu\Omega-cm) almost equally well. Down to the low end of the range of Tc0T_{\mathrm{c0}} that we believe are plausible (Tc0≈1.4T_{\mathrm{c0}}\approx1.4 K), the three most heavily irradiated thin-film samples, with Tc<0.4T_{\mathrm{c}}<0.4 K, never quite provide strong enough upper bounds on TcT_{\mathrm{c}} to exclude any hypothetical Tc0T_{\mathrm{c0}} curves. Apparently all such reductions in Tc0T_{\mathrm{c0}} can be compensated for, at least in principle, by postulating smaller values of ρ0,offset\rho_{0,\mathrm{offset}}. Overall, a more precise and conclusive realization of the basic ideas presented in this section would require collecting more experimental data points in the region near ρ0crit.\rho_{0}^{\mathrm{crit.}}, where TcT_{\mathrm{c}} is supposed to rapidly evolve with changes in ρ0\rho_{0}.

Supplemental Material for “Controllable suppression of the unconventional superconductivity in Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} via high-energy electron irradiation”

Jacob P. Ruf; Hilary M. L. Noad; Romain Grasset; Ludi Miao; Elina Zhakina; Philippa H. McGuinness; Hari P. Nair; Nathaniel J. Schreiber; Naoki Kikugawa; Dmitry Sokolov; Marcin Konczykowski; Darrell G. Schlom; Kyle M. Shen; Andrew P. Mackenzie

FIB-SCULPTED SINGLE CRYSTALS

SampleLength (μm\mu\mathrm{m})Width (μm\mu\mathrm{m})Thickness (μm\mu\mathrm{m})1st dose (C/cm2\mathrm{cm}^{2})2nd dose (C/cm2\mathrm{cm}^{2})
A109.89.76.50.450.60
B80.09.75.51.177–
C101.88.76.50.600.30
D71.28.54.10.300.45

Table S1. Dimensions of the FIB-sculpted single-crystal Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} Hall bars, determined from scanning electron microscope images, and irradiation doses.

GROWTH AND STRUCTURAL CHARACTERIZATION OF EPITAXIAL THIN FILMS

The Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4}/NdGaO3_{3}(110) film was grown by codepositing an elemental strontium flux of 2.2×10132.2 \times10^{13} atoms cm−2s−1\mathrm{cm}^{-2}\mathrm{s}^{-1} and an elemental ruthenium flux of 1.6×10131.6 \times10^{13} atoms cm−2s−1\mathrm{cm}^{-2}\mathrm{s}^{-1} in a background partial pressure of 3×10−63 \times10^{-6} Torr of distilled ozone (≈80%\approx80\% O3_{3} + 20%20\% O2_{2}).

To determine the thickness of the Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4}/NdGaO3_{3}(110) film, we used a lab-based x-ray diffractometer (Rigaku) and Cu-Kα\alpha radiation to measure x-ray diffraction (XRD) data at room temperature along the specular crystal truncation rod of the Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} thin film/NdGaO3_{3} substrate, as shown in Figure S2. Coherent scattering from film crystallites having finite sizes along the out-of-plane direction produces characteristic interference fringes—i.e., secondary maxima and minima—in the XRD intensity surrounding each primary film Bragg peak. The spacing between these fringes scales inversely with the total number of layers in the crystallites, NN; meanwhile, the average interplanar spacing between the layers in each crystallite, c/2c/2, determines where each primary film Bragg peak is centered along the q⊥q_{\perp} axis (here and elsewhere, we use cc to denote the out-of-plane lattice constant of the conventional unit cell of Sr2RuO4). Together these two quantities determine the total film thickness according to t=Nc/2t = Nc/2, which is later needed to convert measured film resistances to resistivities.

Figure S2. Sr2RuO4 film thickness determination. (a) XRD data along the specular crystal truncation rod of the Sr2RuO4(001) thin film/NdGaO3(110) substrate, acquired with Cu-Kα radiation at room temperature. Substrate Bragg peaks are marked by asterisks, and the family of 00L peaks (L even) arising from scattering off the Sr2RuO4 film are labeled accordingly. (b) Zoomed-in view of the experimental data (blue) near the Sr2RuO4 006 and NdGaO3 220 Bragg peaks, with the best-fit simulation overlaid (dashed red).

We utilized the GenX software package [69] to directly fit the experimental XRD data over a region of momentum-transfer space surrounding the Sr2RuO4 006 and NdGaO3 220 Bragg peaks, (q∥≈0q_{\parallel} \approx0, q⊥=1.63q_{\perp} = 1.63–2.122.12 NdGaO3 r.l.u. =2.66= 2.66–3.453.45 1/Å). From these simulations, displayed as a dashed red line in Figure S2, we determined that the Sr2RuO4 film crystallites consisted of 22±122 \pm1 conventional unit cells—i.e., N=44±2N = 44 \pm2 RuO2 planes/layers—stacked along the out-of-plane direction, having an average cc-axis lattice constant of 12.7612.76 Å, and thus a total film thickness of t=(22±1)×12.76t = (22 \pm1) \times12.76 Å =281±13= 281 \pm13 Å. The confidence intervals listed here for tt refer to the estimated scale of film roughnesses, which were incorporated as a parameter in the XRD simulations; thickness variations are likely the largest systematic uncertainty in determining the electrical resistivity of the film in absolute units.

We note that c=12.76c = 12.76 Å for a thin film of Sr2RuO4 corresponds to expansion of the room-temperature bulk single-crystal value (c=12.746c = 12.746 Å [26]) by εzz=+0.11%\varepsilon_{zz} = +0.11\%. Using the relevant Poisson ratio for Sr2RuO4 at 300 K, νzx≡−εzz/εxx=0.207\nu_{zx} \equiv-\varepsilon_{zz}/\varepsilon_{xx} = 0.207 [70], this measured cc-axis expansion is consistent with an elastically strained thin film subject to an average in-plane compressive strain of (εxx+εyy)/2=−0.27%(\varepsilon_{xx} + \varepsilon_{yy})/2 = -0.27\%, which agrees well with the nominal in-plane lattice mismatch of Sr2RuO4 and NdGaO3(110) at room temperature, −0.28%-0.28\% [26, 27], as we discuss in more detail below.

The (110) surface of the NdGaO3 crystal structure (described using the non-standard PbmnPbmn setting of space group #62) is spanned by the mutually orthogonal [1] and [110] lattice translation vectors, which impart modest amounts of biaxial (A1g≡(εxx+εyy)/2A_{1g} \equiv(\varepsilon_{xx} + \varepsilon_{yy})/2) in-plane compressive strain and uniaxial (B1g≡εxx−εyyB_{1g} \equiv\varepsilon_{xx} - \varepsilon_{yy}) in-plane strain on the Sr2RuO4 thin film. Specifically, at 295 K, we expect the two in-plane Ru-O-Ru bonding directions along x∥x \parallel Sr2RuO4[100] and y∥y \parallel Sr2RuO4[10] to be compressed by −0.39%∥-0.39\% \parallel NdGaO3[1] and −0.16%∥-0.16\% \parallel NdGaO3[11ˉ01\bar{1}0] relative to unstrained bulk single crystals of Sr2RuO4 (a=3.8694a = 3.8694 Å) [26, 27]. These deformations correspond to in-plane A1gA_{1g} and B1gB_{1g} strains of −0.28%-0.28\% and 0.23%0.23\%. At 4 K, the in-plane A1gA_{1g} and B1gB_{1g} components of substrate-imposed misfit strains on Sr2RuO4 become −0.22%-0.22\% and 0.30%0.30\%, respectively, accounting for differences in the thermal expansion of NdGaO3 and Sr2RuO4 [71, 72].

Electrical Characterization of Epitaxial Thin Films

As-grown films

In Figure S3, we summarize the electrical resistivity versus temperature behavior of 15 distinct resistivity bridges patterned on the same Sr2_2RuO4_4/NdGaO3_3(110) mother wafer, measured between 0.4 K and 300 K. Hereafter we denote the resistivity by ρ\rho, which is understood to be shorthand for the ρyy\rho_{yy} component of a resistivity tensor that is defined with respect to a crystallographic coordinate system having x∥x \parallel Sr2_2RuO4_4[100] ∥\parallel NdGaO3_3[1], y∥y \parallel Sr2_2RuO4_4[10] ∥\parallel NdGaO3_3[110], and z∥z \parallel Sr2_2RuO4_4[1] ∥\parallel NdGaO3_3(110). We acquired all data displayed in Figure S3 with the Sr2_2RuO4_4 thin-film bridges in their as-grown states—i.e., before subjecting the samples to any doses of high-energy electron irradiation. The graded color scale of the data traces visually represents and corresponds to the ordering of the samples when they are sorted by their residual resistivity ratios (RRRs), defined here as RRR≡ρ(300 K)/ρ(2 K)RRR \equiv\rho(300\ \mathrm{K})/\rho(2\ \mathrm{K}), which range from about 70 (yellow-orange) to 110 (dark purple).

Figure S3. Electrical transport properties across 15 distinct as-grown Sr2_2RuO4_4 thin-film resistivity bridges. Data for a given sample are plotted using the same color in all panels; this color visually encodes the RRR≡ρ(300 K)/ρ(2 K)RRR \equiv\rho(300\ \mathrm{K})/\rho(2\ \mathrm{K}) measured for that sample, as indicated by the inset legend in (a). (a) Absolute resistivities versus temperature. (b) Log-log plot of the scaled resistivities versus temperature. Data are omitted for temperatures between about 2 K−3 K2\ \mathrm{K} - 3\ \mathrm{K} where helium-3 circulation starts/stops in the cryostat used for these measurements; the according rapid changes in temperature prohibit proper thermalization of the samples in this range of TT. (c) Scaled resistivities versus temperature squared. All traces deviate in a subtle, but apparently systematic, fashion at low temperatures from the oft-prescribed ρ0+AT2\rho_0 + AT^2 power-series expansion, which precludes extrapolating the resistivity below TcT_c based on fits to such a power law above TcT_c. (d) Scaled resistivities versus temperature, zoomed in for T≤2 KT \le2\ \mathrm{K} to visualize the superconducting transitions across distinct samples. Inset displays the resistively-measured TcT_cs [criterion: where ρ(T)\rho(T) crosses 50% of ρ(2 K)\rho(2\ \mathrm{K})], plotted against ρ(2 K)\rho(2\ \mathrm{K}), which is employed as an approximation of the residual resistivity. Error bars on TcT_c are the temperatures where ρ(T)\rho(T) crosses the 10% and 80% thresholds of ρ(2 K)\rho(2\ \mathrm{K}). Neither TcT_c nor the superconducting transition widths exhibit any discernible correlation with ρ(2 K)\rho(2\ \mathrm{K}).

Following previous work [3], we assume that the variation in absolute ρ(300 K)\rho(300\ \mathrm{K}) observed across distinct as-grown resistivity bridges in Figure S3, with values ranging from 120 to 131 μΩ\mu\Omega-cm, is primarily caused by systematic uncertainties in the sample preparation and in the measurements, rather than by any intrinsic differences in the scattering mechanisms relevant to Sr2_2RuO4_4 that relax the charge-carrier momentum in this highly incoherent regime of electrical transport. Likely sources of such errors include variations in the effective cross-sectional thickness that the electrical current is constricted to flow through, as well as small misalignments and discrepancies in the lithographically patterned dimensions of the electrical contacts to different bridges. More microscopically, such variations in the effective cross-sectional thicknesses of the resistance bridges may result from total film thickness variations, out-of-phase boundaries in the film that preferentially nucleate in the vicinity of substrate step edges [10, 33, 34, 73], and/or locally higher-NN Ruddlesden-Popper inclusions/stacking faults that form to accommodate non-stoichiometry in Ru-rich (nominally Sr2_2RuO4_4) epitaxial thin films [18, 19, 21, 33].

Therefore, for all other curves plotted in Figure S3-Figure S3), and throughout the main text and the remainder of the Supplemental Material, we plot so-called ‘scaled ρ(T)\rho(T)’ curves: we first normalize the measured resistance versus temperature R(T)R(T) data for a given bridge by its resistance measured at 300 K, and then we uniformly multiply this normalized data by the arithmetic mean of ρ(300 K)\rho(300\ \mathrm{K}) measured across all as-grown bridges, ρ(300 K)‾=124 μΩ\overline{\rho(300\ \mathrm{K})}=124\ \mu\Omega-cm. We note that the value of ρ(300 K)‾=124 μΩ\overline{\rho(300\ \mathrm{K})}=124\ \mu\Omega-cm (standard deviation about the mean =3 μΩ=3\ \mu\Omega-cm) obtained for the Sr2_2RuO4_4 thin-film resistivity bridges studied in this work agrees well with the established literature value appropriate to bulk Sr2_2RuO4_4 single crystals, ρ(300 K)=121 μΩ\rho(300\ \mathrm{K})=121\ \mu\Omega-cm (standard deviation about the mean =17 μΩ=17\ \mu\Omega-cm) [3]. This quantitative level of agreement indicates that these Sr2_2RuO4_4 films do not contain significant volume fractions of higher-NN Ruddlesden-Popper intergrowths (SrO)(SrRuO3_3)N_N, which for all N≠1N\ne1 compounds have characteristic values of ρ(300 K)≈200 μΩ\rho(300\ \mathrm{K})\approx200\ \mu\Omega-cm [14, 74]. Additionally, we note that the above procedure of computing appropriately scaled ρ(T)\rho(T) values is important only if one wishes to interpret ρ\rho in absolute units—for example, as a proxy for computing the transport lifetime (or transport scattering length) of charged quasiparticle excitations in Sr2_2RuO4_4. By contrast, many of the results contained in this manuscript for irradiation-induced changes in quantities like TcT_c are extracted from relative changes in the measured resistance as a function of temperature, which are independent of any remaining systematic errors in the deduced temperature-independent scale factors that enter into conversions of RR to ρ\rho.

From the data in Figure S3, we determined (arithmetic mean ±\pm one standard deviation) values of ρ(300 K)‾=124±3 μΩ\overline{\rho(300\ \mathrm{K})}=124\pm3\ \mu\Omega-cm, ρ(2 K)‾=1.33±0.17 μΩ\overline{\rho(2\ \mathrm{K})}=1.33\pm0.17\ \mu\Omega-cm, and Tc‾=1.359±0.024 K\overline{T_c}=1.359\pm0.024\ \mathrm{K}. Here TcT_c is reported as the temperature at which the resistance of each Sr2_2RuO4_4 thin-film bridge measured at a current of I=10 μAI=10\ \mu\mathrm{A}—or equivalently, at a nominal current density of ∣J∣=440 A/cm2|\mathbf{J}|=440\ \mathrm{A/cm^2}—crosses 50% of its value measured at 2 K. Section IV of the Supplemental Material contains further discussion of the definitions and analysis methods used to extract the values of TcT_c shown in this work. The uniformity of the resistively measured TcT_cs across the wafer (0.024/1.359 = 1.8%) justifies our use of different bridges as nearly-identical ‘initial conditions’ for gauging the effects of different electron irradiation doses on TcT_c. On the other hand, the comparatively larger spread in ρ(2 K)\rho(2\ \mathrm{K}) across the wafer (0.17/1.33 = 13%), the lack of any discernible correlation between TcT_c and ρ(2 K)\rho(2\ \mathrm{K}) for this set of as-grown samples [see inset to Figure S3], and the large absolute values of ρ(2 K)\rho(2\ \mathrm{K}) at which superconductivity remains robustly observed (“large” relative to the phenomenological dependence of TcT_c versus ρ0\rho_0 established for bulk Sr2_2RuO4_4 single crystals, such as in Figure 3 of the main text), all suggest that scattering from most of the native defects existing in these Sr2_2RuO4_4 epitaxial thin films does not appreciably contribute to TcT_c suppression.

Films before and after irradiation

In Figure S4, we show all of the low-temperature, zero-field electrical transport data for Sr2_2RuO4_4 thin films that underlie the data points included in Figure 2(b,Figure 2d) and Figure 3 of the main text. Each panel of Figure S4 focuses on one—or sometimes two, to check reproducibility—distinct Sr2_2RuO4_4 thin-film resistivity bridge(s), and plots the ρ(T)\rho(T) data trace(s) measured before and after incrementing the dose DD of 2.5 MeV electron irradiation received by the sample(s). We used excitation currents of I=1 μAI=1\ \mu\mathrm{A} (J=44 A/cm2J=44\ \mathrm{A/cm^2}) to measure all data displayed in Figure S4. No discernible shifts of the measured TcT_cs occur for I≤1 μAI\le1\ \mu\mathrm{A} in either the as-grown or irradiated samples; on the other hand, increasing the excitation current to I=10 μAI=10\ \mu\mathrm{A} causes all measured TcT_cs to decrease by about 0.02 K [cf. Fig. S3(d)].

All ρ(T)\rho(T) data displayed in Figure S4 are scaled resistivities, computed according to the procedure described in Figure S3 and Sec. III A above. By normalizing all raw R(300 K)R(300\ \mathrm{K}) values (experimentally measured before and after irradiation) to a common value of ρ(300 K)‾=124 μΩ\overline{\rho(300\ \mathrm{K})}=124\ \mu\Omega-cm, we intend to disentangle and to isolate the irradiation-induced modifications in RRRsRRRs from potential irradiation-induced modifications to the effective cross-sectional area of the conducting channel specific to each thin-film resistivity bridge. We believe that the former effects are the physically relevant changes needed to understand and to interpret the response of superconductivity in Sr2_2RuO4_4 to high-energy electron irradiation, which is the focus of this manuscript.

We do (somewhat irregularly) observe hints suggestive of the latter type of effects, however, such as nearly-temperature-independent scaling of the pre-irradiation R(T)R(T) curve for a given bridge by a factor of 1.02 − 1.03 after irradiation. Although other explanations of this are possible and should be investigated in more detail in future work, we note that one of the simplest scenarios—as suggested, e.g., for SrRuO3_3 thin films in Ref. [53]—would involve migration of irradiation-induced interstitial defects to the surfaces of the thin-film samples in a way that reduces the conducting film thickness by about one RuO2_2 monolayer. This would result in a fractional increase in measured resistances of about 1/44=2.3%1/44 = 2.3\% for a Sr2RuO4\mathrm{Sr_2RuO_4} thin film that originally consisted of about 44 RuO2\mathrm{RuO_2} monolayers, in addition to the irradiation-induced changes in the temperature-dependent resistivity of the remaining intact 43 layers.

Independent of the above considerations about how seriously to interpret the plotted values of ρ\rho in absolute units for the Sr2RuO4\mathrm{Sr_2RuO_4} epitaxial thin-film samples, the low and intermediate irradiation doses (D=0.20−0.60 C/cm2D = 0.20 - 0.60\ \mathrm{C/cm^2}) displayed in Figure S4 clearly cause modest reductions of TcT_\mathrm{c} by several tenths of a Kelvin, and the highest irradiation doses (D=1.00 C/cm2D = 1.00\ \mathrm{C/cm^2}) are sufficient to reduce TcT_\mathrm{c} from 1.30−1.40 K1.30 - 1.40\ \mathrm{K} (as grown) to values after irradiation that are well below the base temperature of the helium-3 cryostat used for these measurements, 0.4 K.

Determining ρ0\rho_0 and TcT_c from resistivity

FIB-sculpted single crystals

For the FIB-sculpted single crystals of Sr2_2RuO4_4, we determined the extrapolated zero-temperature normal-state (ns) residual resistivities, ρ0≡ρns(T→0 K)\rho_0 \equiv\rho_{\mathrm{ns}}(T \to0\ \mathrm{K}), and superconducting TcT_cs from resistivity data collected upon cooling and warming between 2 K and 0.4 K. We found ρ0\rho_0 by fitting the ρ(T>Tc)\rho(T > T_c) cooling and warming data together to the quadratic functional form ρns(T)=ρ0+AT2\rho_{\mathrm{ns}}(T) = \rho_0 + AT^2 (Figure S5, black), following previous work in the literature [3]. Across four distinct as-grown samples, we obtained fitted AA coefficients ranging from 6.9 to 8.2 nΩ\Omega-cm/K2^2, in agreement with the values A=4A = 4 to 12 nΩ\Omega-cm/K2^2 reported in the literature [75, 76, 77, 78, 79].

To extract TcT_c, we initially treated the superconducting transitions measured upon warming and cooling separately (red and blue data points in Figure S5, respectively), in order to check for hysteresis. We fitted ρ(T)\rho(T) data in the transition region to a linear function ρtrans(T)=x0+x1T\rho_{\mathrm{trans}}(T) = x_0 + x_1T, and data in the superconducting state (Figure S5, gray) to a constant function ρsc=x2\rho_{\mathrm{sc}} = x_2. From the fitted coefficients {x0,x1,x2}\{x_0, x_1, x_2\}, we then calculated the temperatures where ρns(T)\rho_{\mathrm{ns}}(T) intersects ρtrans(T)\rho_{\mathrm{trans}}(T) and where ρtrans(T)\rho_{\mathrm{trans}}(T) intersects ρsc\rho_{\mathrm{sc}}, to find the onset and completion transition temperatures, respectively. Since the experimental ρtrans(T)\rho_{\mathrm{trans}}(T) behavior is described well by straight lines for all samples we have measured, we took TcT_c to be the midpoint between the onset and completion transition temperatures. Because the thermal hysteresis between cooling and warming data is quite small—at most 0.017 K and typically < 0.010 K—throughout the manuscript we report TcT_c as the arithmetic mean of the values obtained upon cooling and warming.

Epitaxial thin films

In Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} epitaxial thin films, the measured normal-state resistivities ρns(T)\rho_{\mathrm{ns}}(T) (Figure S3) do not follow the oft-prescribed ρ0+AT2\rho_{0} + AT^{2} power-series expansion over a region that is wide enough in temperature to justify fitting the data to this functional form, which precludes using the results of such fits to extrapolate ρns(T)\rho_{\mathrm{ns}}(T) below TcT_{\mathrm{c}}. Accordingly, we adopted slightly more empirical approaches to extract values of ρ0\rho_{0} and TcT_{\mathrm{c}} to use in plots and analyses throughout the main text and Supplemental Material: we set ρ0=ρ(2 K)\rho_{0} = \rho(2\ \mathrm{K}) (i.e., simply equal to the measured resistivity at 2 K); we define TcT_{\mathrm{c}} to be the temperature at which ρ(T)\rho(T) crosses the 50% threshold of ρ(2 K)\rho(2\ \mathrm{K}); finally, we quote “error bars” on TcT_{\mathrm{c}} as the temperatures at which ρ(T)\rho(T) crosses the 80% and 10% thresholds of ρ(2 K)\rho(2\ \mathrm{K}), respectively. Any effects of thermal hysteresis on the resistively measured superconducting transitions for Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} thin films are negligibly small compared to other, likely extrinsic, factors that broaden these transitions, such as static material inhomogeneities; therefore, all plotted and analyzed ρ(T)\rho(T) data for T<2.3 KT < 2.3\ \mathrm{K} were acquired upon gradually warming up the thin-film samples, starting from near the base temperature of the helium-3 cryostat.

We note in passing that if one insists on fitting the Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} thin-film transport data to ρns(T)=ρ0+AT2\rho_{\mathrm{ns}}(T) = \rho_{0} + AT^{2}, e.g., over the interval T:[3 K−5 K]T : [3\ \mathrm{K} - 5\ \mathrm{K}], the resulting fit coefficients range from A=7.7A = 7.7 to 8.4 nΩ-cm/K28.4\ \mathrm{n\Omega\text{-}cm/K}^{2} and ρ0=1.10\rho_{0} = 1.10 to 1.73 μΩ-cm1.73\ \mathrm{\mu\Omega\text{-}cm} across the 15 as-grown samples shown in Figure S3. Extending the fitting range to higher temperatures yields systematically smaller fitted AA coefficients and larger fitted values of ρ0\rho_{0}. Additionally, we note that the relative contribution of temperature-dependent scattering mechanisms to ρ(2 K)\rho(2\ \mathrm{K}) in Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} can be estimated using published results of fits to ρns(T)=ρ0+AT2\rho_{\mathrm{ns}}(T) = \rho_{0} + AT^{2}, which find that A=4A = 4 to 12 nΩ-cm/K212\ \mathrm{n\Omega\text{-}cm/K}^{2} [75, 76, 77, 78, 79], and hence ρ(2 K)−ρ0=16\rho(2\ \mathrm{K}) - \rho_{0} = 16 to 48 nΩ-cm48\ \mathrm{n\Omega\text{-}cm}. On the other hand, the as-grown and irradiated Sr2RuO4\mathrm{Sr}_{2}\mathrm{RuO}_{4} thin films studied in this work have measured ρ(2 K)=1\rho(2\ \mathrm{K}) = 1 to 2 μΩ-cm2\ \mathrm{\mu\Omega\text{-}cm} (Figure S3 and Figure S4). Thus, our ad hoc assignment of ρ0=ρ(2 K)\rho_{0} = \rho(2\ \mathrm{K}) will generally overestimate the hypothetical “true” values of ρ0\rho_{0} by 1 to 5%.

References

  1. [1]A. P. Mackenzie and Y. Maeno, The superconductivity of Sr₂RuO₄ and the physics of spin-triplet pairing, Rev. Mod. Phys. 75, 657 (2003).DOI
  2. [2]A. P. Mackenzie, T. Scaffidi, C. W. Hicks, and Y. Maeno, Even older after twenty-three years: the superconducting order parameter puzzle of Sr₂RuO₄, npj Quantum Mater. 2, 1 (2017).arxiv.org/abs/1706.01942
  3. [3]A. P. Mackenzie, R. K. W. Haselwimmer, A. W. Tyler, G. G. Lonžarich, Y. Mori, S. Nishizaki, and Y. Maeno, Extremely Strong Dependence of Superconductivity on Disorder in Sr₂RuO₄, Phys. Rev. Lett. 80, 161 (1998).DOI
  4. [4]N. Kikugawa, S. Saita, M. Minakata, and Y. Maeno, Effect of Ti substitution on the residual resistivity in the spin-triplet superconductor Sr₂RuO₄, Physica B 312-313, 803 (2002).DOI
  5. [5]N. Kikugawa, A. Peter Mackenzie, and Y. Maeno, Effects of In-Plane Impurity Substitution in Sr₂RuO₄, J. Phys. Soc. Jpn. 72, 237 (2003).DOI
  6. [6]N. Kikugawa, A. P. Mackenzie, C. Bergemann, R. A. Borzi, S. A. Grigera, and Y. Maeno, Rigid-band shift of the Fermi level in the strongly correlated metal: Sr₂−yLayRuO₄, Phys. Rev. B 70, 060508 (2004).DOI
  7. [7]H. Suderow, J. P. Brison, J. Flouquet, A. W. Tyler, and Y. Maeno, Very low temperature thermal conductivity in the layered perovskite superconductor Sr₂RuO₄, J. Phys.: Condens. Matter 10, L597 (1998).
  8. [8]Z. Q. Mao, Y. Mori, and Y. Maeno, Suppression of superconductivity in Sr₂RuO₄ caused by defects, Phys. Rev. B 60, 610 (1999).
  9. [9]M. Uchida, I. Sakuraba, M. Kawamura, M. Ide, K. S. Takahashi, Y. Tokura, and M. Kawasaki, Characterization of Sr₂RuO₄ Josephson junctions made of epitaxial films, Phys. Rev. B 101, 035107 (2020).
  10. [10]Y. Fang, H. P. Nair, L. Miao, B. Goodge, N. J. Schreiber, J. P. Ruf, L. F. Kourkoutis, K. M. Shen, D. G. Schlom, and B. J. Ramshaw, Quantum oscillations and quasiparticle properties of thin film Sr₂RuO₄, Phys. Rev. B 104, 045152 (2021).DOI
  11. [11]H. Noad, E. M. Spanton, K. C. Nowack, H. Inoue, M. Kim, T. A. Merz, C. Bell, Y. Hikita, R. Xu, W. Liu, A. Vailionis, H. Y. Hwang, and K. A. Moler, Variation in superconducting transition temperature due to tetragonal domains in two-dimensionally doped SrTiO₃, Phys. Rev. B 94, 174516 (2016).DOI
  12. [12]C. A. Watson, A. S. Gibbs, A. P. Mackenzie, C. W. Hicks, and K. A. Moler, Micron-scale measurements of low anisotropic strain response of local T_c in Sr₂RuO₄, Phys. Rev. B 98, 094521 (2018).DOI
  13. [13]B. B. Burganov, C. Adamo, A. Mulder, M. Uchida, P. D. C. King, J. W. Harter, D. E. Shai, A. S. Gibbs, A. P. Mackenzie, R. Uecker, M. Bruetzam, M. R. Beasley, C. J. Fennie, D. G. Schlom, and K. M. Shen, Strain Control of Fermiology and Many-Body Interactions in Two-Dimensional Ruthenates, Phys. Rev. Lett. 116, 197003 (2016).
  14. [14]Y. Wang, H. P. Nair, N. J. Schreiber, J. P. Ruf, B. Cheng, D. G. Schlom, K. M. Shen, and N. P. Armitage, Separated transport relaxation scales and interband scattering in thin films of SrRuO₃, CaRuO₃, and Sr₂RuO₄, Phys. Rev. B 103, 205109 (2021).DOI
  15. [15]C. C. Tsuei and J. R. Kirtley, Pair-ing symmetry in cuprate superconductors, Rev. Mod. Phys. 72, 969 (2000).
  16. [16]Y. Maeno, H. Hashimoto, K. Yoshida, S. Nishizaki, T. Fujita, J. G. Bednorz, and F. Lichtenberg, Superconductivity in a layered perovskite without copper, Nature 372, 532 (1994).DOI
  17. [17]Y. Krockenberger, M. Uchida, K. S. Takahashi, M. Nakamura, M. Kawasaki, and Y. Tokura, Growth of superconducting Sr₂RuO₄ thin films, Appl. Phys. Lett. 97, 082502 (2010).DOI
  18. [18]M. Uchida, M. Ide, H. Watanabe, K. S. Takahashi, Y. Tokura, and M. Kawasaki, Molecular beam epitaxy growth of superconducting Sr₂RuO₄ films, APL Mater. 5, 106108 (2017).
  19. [19]H. P. Nair, J. P. Ruf, N. J. Schreiber, L. Miao, M. L. Grandon, D. J. Baek, B. H. Goodge, J. P. C. Ruff, L. F. Kourkoutis, K. M. Shen, and D. G. Schlom, Demystifying the growth of superconducting Sr₂RuO₄ thin films, APL Mater. 6, 101108 (2018).DOI
  20. [20]C. M. P. Garcia, A. Di Bernardo, G. Kimbell, M. E. Vickers, F. C.-P. Massabuau, S. Komori, G. Divitini, Y. Yasui, H. G. Lee, J. Kim, B. Kim, M. G. Blamire, A. Vecchione, R. Fittipald, Y. Maeno, T. W. Noh, and J. W. A. Robinson, Pair suppression caused by mosaic-twist defects in superconducting Sr₂RuO₄ thin-films prepared using pulsed laser deposition, Commun. Mater. 1, 23 (2020).
  21. [21]J. Kim, J. Mun, C. M. Palomares García, B. Kim, R. S. Perry, Y. Jo, H. Im, H. G. Lee, E. K. Ko, S. H. Chang, S. B. Chung, M. Kim, J. W. A. Robinson, S. Yonezawa, Y. Maeno, L. Wang, and T. W. Noh, Superconducting Sr₂RuO₄ Thin Films without Out-of-Phase Boundaries by Higher-Order Ruddlesden–Popper Intergrowth, Nano Lett. 21, 4185 (2021).DOI
  22. [22]V. Sunko, P. H. McGuinness, C. S. Chang, E. Zhakina, S. Khim, C. E. Dreyer, M. Konczykowski, H. Borrmann, P. J. W. Moll, M. König, D. A. Muller, and A. P. Mackenzie, Controlled Introduction of Defects to Delafossite Metals by Electron Irradiation, Phys. Rev. X 10, 021018 (2020).DOI
  23. [23]J. S. Bobowski, N. Kikugawa, T. Miyoshi, H. Suwa, H.-s. Xu, S. Yonezawa, D. A. Sokolov, A. P. Mackenzie, and Y. Maeno, Improved Single-Crystal Growth of Sr₂RuO₄, J. Condens. Matter 4, 6 (2019).DOI
  24. [24]See Supplemental Material at [URL will be inserted by publisher] for further details on samples, electrical characterization of films, and a discussion of the determination of ρ₀ and T_c. Includes references [69–79].
  25. [25]H. P. Nair, Y. Liu, J. P. Ruf, N. J. Schreiber, S.-L. Shang, D. J. Baek, B. H. Goodge, L. F. Kourkoutis, Z.-K. Liu, K. M. Shen, and D. G. Schlom, Synthesis science of SrRuO₃ and CaRuO₃ epitaxial films with high residual resistivity ratios, APL Mater. 6, 046101 (2018).
  26. [26]L. Walz and F. Lichtenberg, Refinement of the structure of Sr₂RuO₄ with 100 and 295 K X-ray data, Acta Crystallogr. Sect. C 49, 1268 (1993).DOI
  27. [27]M. Schmidbauer, A. Kwasniewski, and J. Schwarzkopf, High-precision absolute lattice parameter determination of SrTiO₃, DyScO₃ and NdGaO₃ single crystals, Acta Crystallogr. Sect. B 68, 8 (2012).DOI
  28. [28]M. E. Barber, Uniaxial stress technique and investiga tions into correlated electron systems, Ph.D. thesis, University of St. Andrews (2017).
  29. [29]G. W. Iseler, H. I. Dawson, A. S. Mehner, and J. W. Kauffman, Production Rates of Electrical Resistivity in Copper and Aluminum Induced by Electron Irradiation, Phys. Rev. 146, 468 (1966).DOI
  30. [30]M. Konczykowski and J. Gilchrist, Electron irradiation of YBa₂Cu₃O₇ ceramics, J. Phys. (Paris) III 1, 1765 (1991).DOI
  31. [31]M. J. Berger, J. S. Coursey, M. A. Zucker, and J. Chang, NIST Standard Reference Database 124 (National Institute of Standards and Technology, 2017).
  32. [32]G. Kim, Y. E. Soukolc, J. Herrero-Martin, D. Putzky, H. P. Nair, J. P. Ruf, N. J. Schreiber, C. Dietl, G. Christiani, G. Logvenov, M. Minola, P. A. van Aken, K. M. Shen, D. G. Schlom, and B. Keimer, Electronic and vibrational signatures of ruthenium vacancies in Sr₂RuO₄ thin films, Phys. Rev. Materials 3, 094802 (2019).DOI
  33. [33]B. H. Goodge, H. P. Nair, D. J. Baek, N. J. Schreiber, L. Miao, J. P. Ruf, E. N. Waite, P. M. Carubia, K. M. Shen, D. G. Schlom, and L. F. Kourkoutis, Disentangling types of lattice disorder impacting superconductivity in Sr₂RuO₄ by quantitative local probes, APL Mater. 10, 041114 (2022).DOI
  34. [34]M. A. Zurbuchen, Y. Jia, S. Knapp, A. H. Carim, D. G. Schlom, L.-N. Zou, and Y. Liu, Suppression of superconductivity by crystallographic defects in epitaxial Sr₂RuO₄ films, Appl. Phys. Lett. 78, 2351 (2001).DOI
  35. [35]M. A. Zurbuchen, Y. Jia, S. Knapp, A. H. Carim, D. G. Schlom, and X. Q. Pan, Defect generation by preferred nucleation in epitaxial Sr₂RuO₄/LaAlO₃, Appl. Phys. Lett. 83, 3891 (2003).DOI
  36. [36]M. A. Zurbuchen, W. Tian, X. Q. Pan, D. Fong, S. K. Streiffer, M. E. Hawley, J. Lettieri, Y. Jia, G. Asayama, S. J. Fulk, D. J. Comstock, S. Knapp, A. H. Carim, and D. G. Schlom, Morphology, structure, and nucleation of out-of-phase boundaries (OPBs) in epitaxial films of layered oxides, J. Mater. Res. 22, 1439 (2007).DOI
  37. [37]A. Steppke, L. Zhao, M. E. Barber, T. Scaffidi, F. Jerzembeck, H. Rosner, A. S. Gibbs, Y. Maeno, S. H. Simon, A. P. Mackenzie, and C. W. Hicks, Strong peak in T_c of Sr₂RuO₄ under uniaxial pressure, Science 355, eaaf9398 (2017).
  38. [38]A. P. Mackenzie, Recent progress in electron probe microanalysis, Rep. Prog. Phys. 56, 557 (1993).DOI
  39. [39]S. Nishizaki, Y. Maeno, and Z. Mao, Effect of Impurities on the Specific Heat of the Spin-Triplet Superconductor Sr₂RuO₄, J. Low Temp. Phys. 117, 1581 (1999).DOI
  40. [40]Y.-S. Li, N. Kikugawa, D. A. Sokolov, F. Jerzembeck, A. S. Gibbs, Y. Maeno, C. W. Hicks, J. Schmalian, M. Nicklas, and A. P. Mackenzie, High-sensitivity heat-capacity measurements on Sr₂RuO₄ under uniaxial pressure, Proc. Natl. Acad. Sci. USA 118, e2020492118 (2021).DOI
  41. [41]Y.-S. Li, M. Garst, J. Schmalian, S. Ghosh, N. Kikugawa, D. A. Sokolov, C. W. Hicks, F. Jerzembeck, M. S. Ikeda, Z. Hu, B. J. Ramshaw, A. W. Rost, M. Nicklas, and A. P. Mackenzie, Elastocaloric determination of the phase diagram of Sr₂RuO₄, Nature 607, 276 (2022).DOI
  42. [42]S. Ghosh, A. Shekhter, F. Jerzembeck, N. Kikugawa, D. A. Sokolov, M. Brando, A. P. Mackenzie, C. W. Hicks, and B. J. Ramshaw, Thermodynamic evidence for a two-component superconducting order parameter in Sr₂RuO₄, Nat. Phys. 17, 199 (2021).DOI
  43. [43]S. Benhabib, C. Lupien, I. Paul, L. Berges, M. Dion, M. Nardone, A. Zitouni, Z. Q. Mao, Y. Maeno, A. Georges, L. Taillefer, and C. Proust, Ultrasound evidence for a two-component superconducting order parameter in Sr₂RuO₄, Nat. Phys. 17, 194 (2021).DOI
  44. [44]S. A. Kivelson, A. C. Yuan, B. Ramshaw, and R. Thomale, A proposal for reconciling diverse experiments on the superconducting state in Sr₂RuO₄, npj Quantum Mater. 5, 1 (2020).DOI
  45. [45]G. M. Luke, Y. Fudamoto, K. M. Kojima, M. I. Larkin, J. Merrin, B. Nachumi, Y. J. Uemura, Y. Maeno, Z. Q. Mao, Y. Mori, H. Nakamura, and M. Sigrist, Time-reversal symmetry-breaking superconductivity in Sr₂RuO₄, Nature 394, 558 (1998).DOI
  46. [46]V. Grinenko, S. Ghosh, R. Sarkar, J.-C. Orain, A. Nikitin, M. Elender, D. Das, Z. Guguchia, F. Brückner, M. E. Barber, J. Park, N. Kikugawa, D. A. Sokolov, J. S. Bobkowski, T. Miyoshi, Y. Maeno, A. P. Mackenzie, H. Luetkens, C. W. Hicks, and H.-H. Klauss, Split superconducting and time-reversal symmetry-breaking transitions in Sr₂RuO₄ under stress, Nat. Phys. 17, 748 (2021).DOI
  47. [47]V. Grinenko, D. Das, R. Gupta, B. Zinkl, N. Kikugawa, Y. Maeno, C. W. Hicks, H.-H. Klauss, M. Sigrist, and R. Khasanov, Unsplit superconducting and time reversal symmetry breaking transitions in Sr₂RuO₄ under hydrostatic pressure and disorder, Nat. Commun. 12, 3920 (2021).
  48. [48]J. Xia, Y. Maeno, P. T. Beyersdorf, M. M. Fejer, and A. Kapitulnik, High Resolution Polar Kerr Effect Measurements of Sr₂RuO₄: Evidence for Broken Time-Reversal Symmetry in the Superconducting State, Phys. Rev. Lett. 97, 167002 (2006).pubmed.ncbi.nlm.nih.gov/17155427
  49. [49]S. K. Tolpygo, J.-Y. Lin, M. Gurvitch, S. Y. Hou, and J. M. Phillips, Effect of oxygen defects on transport properties and T_c of YBa₂Cu₃O₆+x: Displacement energy for plane and chain oxygen and implications for irradiation-induced resistivity and T_c suppression, Phys. Rev. B 53, 12462 (1996).
  50. [50]S. K. Tolpygo, J.-Y. Lin, M. Gurvitch, S. Y. Hou, and J. M. Phillips, Universal T_c suppression by in-plane defects in high-temperature superconductors: Implications for pairing symmetry, Phys. Rev. B 53, 12454 (1996).
  51. [51]Dataset for Ruf et al. “Controllable suppression of the unconventional superconductivity in Sr₂RuO₄ via high-energy electron irradiation” (2024); DOI to be inserted here.
  52. [52]L. Klein, Y. Kats, N. Wiser, M. Konczykowski, J. W. Reiner, T. H. Geballe, M. R. Beasley, and A. Kapitulnik, Negative deviations from Matthiesen’s rule for SrRuO₃ and CaRuO₃, Europhys. Lett. 55, 532 (2001).
  53. [53]N. Haham, M. Konczykowski, B. Kuiper, G. Koster, and L. Klein, Testing dependence of anomalous Hall effect on resistivity in SrRuO₃ by its increase with electron irradiation, Phys. Rev. B 88, 214431 (2013).DOI
  54. [54]A. Legris, F. Rullier-Albenque, E. Radeva, and P. Lejay, Effects of electron irradiation on YBa₂Cu₃O₇−δ superconductor, J. Phys. (Paris) I 3, 1605 (1993).
  55. [55]T. Li, H. Qing, and L. Xhengming, Analytic Fitting to the Mott Cross Section of Electrons, Radiat. Phys. Chem. 45, 235 (1995).
  56. [56]M. J. Boschini, C. Consolandi, M. Gervasi, S. Giani, D. Grandi, V. Ivanchenko, P. Nieminen, S. Pensotti, P. G. Rancoita, and M. Tacconi, An expression for the Mott cross section for electrons and positrons on nuclei with Z up to 118, Radiat. Phys. Chem. 90, 39 (2013).
  57. [57]M. Tinkham, Effect of Fluxoid Quantization on Transitions of Superconducting Films, Phys. Rev. 129, 2413 (1963).DOI
  58. [58]F. E. Harper and M. Tinkham, The Mixed State in Superconducting Thin Films, Phys. Rev. 172, 441 (1968).DOI
  59. [59]M. Uchida, M. Ide, M. Kawamura, K. S. Takahashi, Y. Kozuka, Y. Tokura, and M. Kawasaki, Anomalous enhancement of upper critical field in Sr2RuO4 thin films, Phys. Rev. B 99, 161111 (2019).
  60. [60]J. W. P. Hsu and A. Kapitulnik, Superconducting transition, fluctuation, and vortex motion in a two-dimensional single-crystal Nb film, Phys. Rev. B 45, 4819 (1992).pubmed.ncbi.nlm.nih.gov/10002120
  61. [61]A. A. Abrikosov and L. P. Gor’kov, Contribution to the theory of superconducting alloys with paramagnetic impurities, Sov. Phys. JETP 12, 1243 (1961).
  62. [62]P. Hohenberg, Anisotropic superconductors with non-magnetic impurities, Sov. Phys. JETP 18, 834 (1964).
  63. [63]A. A. Abrikosov, Influence of the gap anisotropy on superconducting properties, Physica C 214, 107 (1993).DOI
  64. [64]R. J. Radtke, K. Levin, H.-B. Schüttler, and M. R. Norman, Predictions for impurity-induced Tc suppression in the high-temperature superconductors, Phys. Rev. B 48, 653 (1993).DOI
  65. [65]L. S. Borkowski and P. J. Hirschfeld, Distinguishing d-wave superconductors from highly anisotropic s-wave superconductors, Phys. Rev. B 49, 15404 (1994).DOI
  66. [66]L. A. Openov, Critical temperature of an anisotropic superconductor containing both nonmagnetic and magnetic impurities, Phys. Rev. B 58, 9468 (1998).DOI
  67. [67]P. B. Allen, New method for solving Boltzmann’s equation for electrons in metals, Phys. Rev. B 17, 3725 (1978).DOI
  68. [68]A. A. Golubov and I. I. Mazin, Effect of magnetic and nonmagnetic impurities on highly anisotropic superconductivity, Phys. Rev. B 55, 15146 (1997).DOI
  69. [69]M. Björck and G. Andersson, GenX: an extensible X-ray reflectivity refinement program utilizing differential evolution, J. Appl. Crystallogr. 40, 1174 (2007).DOI
  70. [70]J. Paglione, C. Lupien, W. A. MacFarlane, J. M. Perz, L. Taillefer, Z. Q. Mao, and Y. Maeno, Elastic tensor of Sr2RuO4, Phys. Rev. B 65, 220506 (2002).DOI
  71. [71]A. Seneshyn, D. M. Trots, J. M. Engel, L. Vasylychko, H. Ehrenberg, T. Hansen, M. Berkowski, and H. Fuess, Anomalous thermal expansion in rare-earth gallium perovskites: a comprehensive powder diffraction study, J. Phys. Condens. Matter 21, 145405 (2009).
  72. [72]T. Vogt and D. J. Buttrey, Low-temperature structural behavior of Sr2RuO4, Phys. Rev. B 52, R9843 (1995).pubmed.ncbi.nlm.nih.gov/9980128
  73. [73]J. Wu, H. P. Nair, A. T. Bollinger, X. He, I. Robinson, N. J. Schreiber, K. M. Shen, D. G. Schlom, and I. Božović, Electronic nematicity in Sr2RuO4, Proc. Natl. Acad. Sci. USA 117, 10654 (2020).DOI
  74. [74]L. Capogna, A. P. Mackenzie, R. S. Perry, S. A. Grigera, L. M. Galvin, P. Raychaudhuri, A. J. Schofield, C. S. Alexander, G. Cao, S. R. Julian, and Y. Maeno, Sensitivity to Disorder of the Metallic State in the Ruthenates, Phys. Rev. Lett. 88, 076602 (2002).pubmed.ncbi.nlm.nih.gov/11863926
  75. [75]D. Forsythe, S. R. Julian, C. Bergemann, E. Pugh, M. J. Steiner, P. L. Alireza, G. J. McMullan, F. Nakamura, R. K. W. Haselwimmer, I. R. Walker, S. S. Saxena, G. G. Lonzarich, A. P. Mackenzie, Z. Q. Mao, and Y. Maeno, Evolution of Fermi-Liquid Interactions in Sr2RuO4 under Pressure, Phys. Rev. Lett. 89, 166402 (2002).
  76. [76]T. Akima, S. NishiZaki, and Y. Maeno, Intrinsic Superconducting Parameters of Sr2RuO4, J. Phys. Soc. Jpn. 68, 694 (1999).DOI
  77. [77]Y. Maeno, K. Yoshida, H. Hashimoto, S. Nishizaki, S.-i. Ikeda, M. Nohara, T. Fujita, A. P. Mackenzie, N. E. Hussey, J. G. Bednorz, and F. Lichtenberg, Two-Dimensional Fermi Liquid Behavior of the Superconductor Sr2RuO4, J. Phys. Soc. Jpn. 66, 1405 (1997).
  78. [78]N. E. Hussey, A. P. Mackenzie, J. R. Cooper, Y. Maeno, S. Nishizaki, and T. Fujita, Normal-state magnetoresistance of Sr2RuO4, Phys. Rev. B 57, 5505 (1998).DOI
  79. [79]M. E. Barber, A. S. Gibbs, Y. Maeno, A. P. Mackenzie, and C. W. Hicks, Resistivity in the Vicinity of a van Hove Singularity: Sr2RuO4 under Uniaxial Pressure, Phys. Rev. Lett. 120, 076602 (2018).

Paper details

vlnc:W_c3zma745
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents