betaFeedback

WorksPhysics and Astronomy

Unidirectional spin Hall magnetoresistance and spin-orbit torques in HM1_1/Co/HM2_2 trilayer systems

Abstract

We present a detailed analysis of harmonic longitudinal and Hall voltage measurements for in-plane magnetized Pt/Co/Ta and Ta/Co/Pt trilayers in reference to Pt/Co and Ta/Co bilayers. Enhancement of spin-orbit torques (SOTs) and unidirectional spin Hall magnetoresistance (USMR) is achieved by introducing the second heavy metal (HM) with the opposite sign of the spin Hall angle. The extracted SOT efficiencies are larger for the trilayers as compared to the bilayers, confirming the enhanced values reported for the trilayers with perpendicularly magnetized Co. The maximum effective spin Hall angle found for the Pt/Co/Ta trilayer reaches θSHθ_{SH} = 20%. The USMR of the trilayer yields up to 27% higher effect as for the respective bilayers with the largest effective USMR amplitude of -0.32 ×\times 10−5^{-5} for the Pt/Co/Ta trilayer at a charge current density of 107^{7} A/cm2^2.

Introduction

Magnetoresistive (MR) effects play an important role in today’s spintronic research [1, 2]. Anisotropic magnetoresistance, giant magnetoresistance and tunneling magnetoresistance are widely used for memory applications [3, 4] or as sensing devices [5].

Recently, a new MR effect has been found in heavy metal (HM)/ferromagnetic insulator (FMI) hybrid structures called the spin Hall magnetoresistance (SMR). It has been intensively studied [6, 7, 8, 9] with additional discussions and reports on HM/ferromagnetic metal (FMM) hybrids [10, 11, 12]. The SMR is based on the spin Hall effect (SHE) [13, 14, 15, 16], which occurs in the HM and converts a charge current into a perpendicular spin current. Due to the inverse SHE, part of the spin current is converted back to the charge current, after it has been reflected from the HM/FMM(FMI) interface. The SHE emerges as a result of the strong spin-orbit coupling in HM materials such as Ta, Pt, W etc.

The perpendicular spin current can cross the interface from HM to FMM, but also from HM to FMI, thus converting from a spin-polarized charge current to a magnon spin current. Depending on the FM magnetization direction with respect to the spin polarization direction at the HM interface, the spin current can produce a torque on the FM’s magnetization. If this SHE-induced spin-orbit torque (SOT) is strong enough, it can even switch the FM magnetization [17, 18]. The SOT magnetization switching is at present intensively studied due to its potential use for memory and logic applications [19, 20, 21].

Nowadays, primarily spin-transfer torque (STT) [22] magnetization switching is used in magnetic tunnel junctions. However, the comparison between the SOT and STT-based MRAM is not straightforward, as was discussed by Grimaldi et al. [23]. The SOT-MRAM requires an improvement of the critical current density to achieve high effectiveness, comparable to STT. However, the combination of both SOT and STT switching, so-called SHE-assisted STT switching can be advantageous and a key to low-power, ultra-fast and high density memory applications [4, 24, 25]. Recent reports discussed that the insertion of light elements or oxidization can enhance the SOT efficiency [26, 27, 28, 29, 30, 31]. One reason could be that additional orbital Hall effects can occur and support the SOT switching [32].

Some of the MR effects depend quadratically on the magnetization m\mathbf{m}, although the physical origin differs from one MR effect to the other. However, Avci et al. explored a new MR effect in Ta/Co/AlOx_x and Pt/Co/AlOx_x called unidirectional spin Hall magnetoresistance (USMR) that is linear in m\mathbf{m} and linear in the charge current density j\mathbf{j} [33]. Up to now, several theoretical studies have been conducted to determine the USMR origins in various metallic bilayer systems. The first reports on HM/FMM thin films associate the USMR with the spin-diffusion theory [34], in which the linear dependence on j\mathbf{j} is due to the SHE-induced spin accumulation at the HM/FMM interface. This spin accumulation can be described as RUSMR2ω∼∣j×m∣R_{\mathrm{USMR}}^{2\omega} \sim|\mathbf{j} \times\mathbf{m}|, with RUSMR2ωR_{\mathrm{USMR}}^{2\omega} being the second harmonic longitudinal resistance term corresponding to USMR. The recent works on similar systems, e.g. permalloy/Pt bilayers [35], discuss that USMR is likely dominated by the dipolar magnons, whereas Avci et al. broaden the understanding of the origins of the effect, attributing it to three different mechanisms: bulk and interface spin-dependent USMR as well as spin-flip USMR [36]. For the case of HM/FMI bilayers, Sterk et al. report USMR due to pure magnonic contributions [37].

The USMR makes it possible to determine the in-plane direction of the magnetization or applied current and has a potential use as a magnetization read out mechanism in a multi-state memory device [38]. After the first report of USMR in HM/FMM bilayers, there have been several follow-up studies including large USMR in FM/paramagnetic GaMnAs bilayers [39] and in topological insulator/FM heterostructures [40], as well as in Heusler compound/HM bilayers [41]. A comprehensive investigation of the thickness dependence of USMR in Pt/Co bilayers has been performed by Yin et al. [42]. Additionally, Hasegawa et al. reported enhancement of the USMR in Pt/Co system with a Cu interlayer [43].

The magnetic proximity effect (MPE) can potentially influence the SOT efficiencies and magnetoresistance effects, as was shown for various HM/FMM bilayer systems [44, 45, 46]. Although, some studies claim irrelevance of the MPE in the bilayer systems with thin Co layer [46] it is essential to know the strength of the MPE for a clear picture of the magnetic properties [47].

In this work, we present a detailed study of the bi- and trilayer structures of HM/FM and HM1_1/FM/HM2_2, respectively. By switching the order of the HM1_1 and HM2_2, we can manipulate the HM/FM interfaces and thus tune both USMR and SOTs. As it was predicted by Zhang and Vignale [34], one expects the enhancement of the USMR in such heterostructures with the FM sandwiched between two HMs with the opposite sign of the spin Hall angle θSH\theta_{\mathrm{SH}}. In such a case, an enhancement of the USMR is expected since both HMs generate spin currents with the same spin orientation, which can be controlled by the charge current direction and/or sign of the θSH\theta_{\mathrm{SH}}. It has been shown already for out-of-plane magnetized Co in a Pt/Co/Ta trilayer that one can tailor the stack and HM/FM interfaces to achieve higher effective θSH\theta_{\mathrm{SH}} [48]. Here, we investigate this approach for in-plane magnetized trilayers.

The sample stacks studied in this work are: sub/Pt 6/ Co 2.5/MgO 2/TaOx_x and sub/Ta 6/Co 2.5/MgO 2/TaOx_x, further mentioned as Pt/Co and Ta/Co bilayers, respectively. The trilayers consisted of sub/Pt 6/ Co 2.5/Ta 6/MgO 2/TaOx_x and sub/Ta 6/Co 2.5/Pt 6/MgO 2/TaOx_x, mentioned here as Pt/Co/Ta and Ta/Co/Pt, respectively. The thicknesses of the layers are indicated in nm. The substrate (sub) used for all the samples was Si/SiO2_2 with an SiO2_2-thickness of 50 μ\mum. The proximity induced moments have been already studied and are published in Ref. [47]. The extracted thicknesses of the Pt spin-polarized layer for the trilayer samples are 0.9 nm and 0.8 nm for Ta/Co/Pt and Pt/Co/Ta, respectively. The induced Pt magnetic moments of 0.56 μB\mu_{\mathrm{B}} per Pt atom at the interface for Ta/Co/Pt and 0.42 μB\mu_{\mathrm{B}} per Pt atom at the interface for Pt/Co/Ta have been extracted [47].

Experimental Details

The samples were prepared by DC magnetron sputtering (except for MgO, for which RF sputtering was used) on thermally oxidized Si substrates at room temperature. The top MgO/TaOx_x is a capping layer to protect the stacks from oxidation. The topmost TaOx_x layer was obtained by natural oxidation of a 2 nm metallic Ta film. In-plane and out-of-plane saturation fields, as well as saturation magnetizations, were determined from vibrating sample magnetometry (VSM) loops measured up to 4 T at room temperature (see Ref. [47]). The samples are in-plane magnetized with Ms=1500M_s = 1500 kA/m for Pt/Co and 1400 kA/m for all the other samples. The in-plane saturation fields are 0.4 T for both trilayers and the Ta/Co bilayer, while Pt/Co exhibits Bs=1.0B_s = 1.0 T. The coercive fields are in the range between 6.8 and 13 mT. The films were further patterned via one-step electron beam lithography into Hall bar structures with a width ww and lengths l=5wl = 5w, as shown in Figure 1.

Microscope image of a 10 $\mu$m wire-bonded Hall bar and electrical connections, with schematic representation of the zoomed-in region

Figure 1. (a) Microscope image of a 10 μ\mum wire-bonded Hall bar and electrical connections. (b) Schematic representation of the zoomed-in region with the geometry definitions.

The harmonic longitudinal and transverse voltage measurements are used here to characterize the spin dependent transport in the samples. The rotational measurements in xyxy plane were carried out inside a dual Halbach cylinder array with a rotating magnetic field in the range from 0.05 to 1 T (MultiMag, Magnetic Solutions Ltd.). By using two Signal Recovery SR7230 Lock-In amplifiers with two demodulators, we were able to measure simultaneously both first (ω\omega) and second (2ω2\omega) harmonics of longitudinal and transverse (Hall) voltages. The measurements were performed at room temperature at a modulation frequency of f=ω/2π=1176f = \omega/2\pi= 1176 Hz and with varied AC current amplitudes up to 2.5 mA. Anomalous Hall resistances RAHER_{\mathrm{AHE}} are obtained from magnetic field loops measured up to 4 T at room temperature.

Results and Discussion

Harmonic Hall voltage analysis: SOTs and thermal effects

First, we present the raw data and fits for the second harmonic transverse (Hall) resistance RH2ωR_{H}^{2\omega} measured as a function of the in-plane rotation angle φ\varphi with respect to the external magnetic field. Figure 2 shows the data for the bi- and trilayers. The data analysis was based on the method developed by Avci et al. [33, 49].

Figure 2. Second harmonic Hall resistances for the studied (a), (b) bi- and (c), (d) trilayers with a Hall bar width of w=4 μmw = 4\,\mu\mathrm{m}. Red and light blue circles correspond to the measured data at 1 and 0.05 T, respectively. The fits (black dashed lines) are based on Eq. (1).

Following the analysis method, we first focus on the transverse second harmonic voltage, to obtain the information on the SOTs as well as to extract the transverse thermal effects. These effects arise from spin Seebeck and anomalous Nernst effects (SSE and ANE respectively) and must be taken into account. The second harmonic Hall voltage can be described as [50, 51]

VH2ω=[−BFL+OeBextRPHEcos⁡2φ+(−12BDLBtotalRAHE+α′I0)]Irmscos⁡φ.(1)V_{H}^{2\omega} = \left[-\frac{B_{\mathrm{FL+Oe}}}{B_{\mathrm{ext}}}R_{\mathrm{PHE}}\cos2\varphi+ \left(-\frac{1}{2}\frac{B_{\mathrm{DL}}}{B_{\mathrm{total}}}R_{\mathrm{AHE}}+\alpha'I_{0}\right)\right]I_{\mathrm{rms}}\cos\varphi. \tag*{(1)}

BFL+OeB_{\mathrm{FL+Oe}} is the field-like (FL) SOT and Oersted field contribution, while BDLB_{\mathrm{DL}} corresponds to the damping-like (DL) SOT field. RPHER_{\mathrm{PHE}} and RAHER_{\mathrm{AHE}} are the planar Hall effect (PHE) and the anomalous Hall effect (AHE) resistances, respectively. The term BtotalB_{\mathrm{total}} is the total magnetic field. The term α′I0\alpha'I_{0} describes any thermal contribution arising from SSE/ANE and IrmsI_{\mathrm{rms}} is the root mean square amplitude of the applied AC charge current. Thus, we can describe the transverse second harmonic resistance as a sum of the contributions

RH2ω=RDL2ω+R∇T2ω+RFL+Oe2ω.(2)R_{H}^{2\omega}=R_{\mathrm{DL}}^{2\omega}+R_{\nabla T}^{2\omega}+R_{\mathrm{FL+Oe}}^{2\omega}. \tag*{(2)}

The term R∇T2ωR_{\nabla T}^{2\omega} corresponds to the thermal effects driven by out-of-plane thermal gradients (SSE, ANE). As one can see from Eq. (1), the first term has a (2cos⁡3φ−cos⁡φ)(2\cos^{3}\varphi-\cos\varphi) dependence, while the remaining two terms follow a cos⁡φ\cos\varphi angular dependence.

We first fit the RH2ωR_{H}^{2\omega} raw data with a acos⁡φ+b(2cos⁡3φ−cos⁡φ)a\cos\varphi+b(2\cos^{3}\varphi-\cos\varphi) function. We then extract the cos⁡φ\cos\varphi contribution, which corresponds to the sum of DL SOT and thermal effects, as well as the (2cos⁡3φ−cos⁡φ)(2\cos^{3}\varphi-\cos\varphi) contribution to extract FL SOT. After the extraction of the cos⁡φ\cos\varphi component, we can further separate the DL and thermal contributions by plotting the corresponding fit parameter against the inverse total magnetic field 1/Btotal1/B_{\mathrm{total}}, with Btotal=Bext+Bdemag−BanisB_{\mathrm{total}}=B_{\mathrm{ext}}+B_{\mathrm{demag}}-B_{\mathrm{anis}}. The term (Bdemag−Banis)(B_{\mathrm{demag}}-B_{\mathrm{anis}}) can be identified as the out-of-plane saturation field. The example of such a separation is shown in Figure 3(a) for the bi- and trilayers. The DL SOT is expected to have no influence in the large field regime. Therefore, the only contribution left at large magnetic fields is related to the thermal effects. The BDLB_{\mathrm{DL}} is extracted from the slope of the linear fits depicted in Figure 3(a). Thus, we define R∇T2ωR_{\nabla T}^{2\omega} as a yy-axis intercept of the 1/Btotal1/B_{\mathrm{total}} plotting. For further calculations of the USMR, we then convert the obtained R∇T2ωR_{\nabla T}^{2\omega} via the geometrical factor l/w=5l/w=5 and subtract it from the raw longitudinal R2ωR^{2\omega}.

Figure 3. (a) RH2ωR_{H}^{2\omega} vs cos⁡φ\cos\varphi contribution plotted against the inverse total magnetic field for the bi- and trilayers. Linear fits performed for the in-plane saturated regime >0.4> 0.4 T. (b) FL and DL SOTs as a function of the external magnetic field. The orange shaded area encloses the data in unsaturated regime.

To calculate the DL and FL SOT fields (BDLB_{\mathrm{DL}} and BFL+OeB_{\mathrm{FL+Oe}}, respectively) we again utilize Eq. (1). Here, the BFL+OeB_{\mathrm{FL+Oe}} term corresponds to a sum of FL SOT and Oersted field contributions. The Oersted field originates from the charge current flowing in the Pt and/or Ta layer(s) and can be estimated as μ0Irms/2w\mu_{0}I_{\mathrm{rms}}/2w, with μ0\mu_{0} as the vacuum permeability, IrmsI_{\mathrm{rms}} as the root-mean-square current amplitude and ww as the width of the current line. BOeB_{\mathrm{Oe}} was estimated to be −0.39-0.39 mT and was subtracted from BFL+OeB_{\mathrm{FL+Oe}} for the FL SOT efficiency calculations. The SOT fields for bi- and trilayers are shown in Figure 3(b). As expected, there is no magnetic field dependence, except for the unsaturated regime in the magnetic field range <0.4< 0.4 T. We calculate the SOT efficiencies (ξDL\xi_{\mathrm{DL}} and ξFL\xi_{\mathrm{FL}}) as [52]

ξDL(FL)=2eℏBDL(FL)MstFMjHM,(3)\xi_{\mathrm{DL(FL)}}=\frac{2e}{\hbar}B_{\mathrm{DL(FL)}}\frac{M_{\mathrm{s}}t_{\mathrm{FM}}}{j_{\mathrm{HM}}}, \tag*{(3)}

with ee being the electron charge, ℏ\hbar the reduced Planck constant, MsM_{\mathrm{s}} and tFMt_{\mathrm{FM}} the saturation magnetization and thickness of the FM, respectively. jHMj_{\mathrm{HM}} is the charge current density amplitude in a HM layer.

Using the DL SOT values, we calculate the spin Hall angle θSH\theta_{\mathrm{SH}}, following a model in which the DL torque is entirely ascribed to the absorption of the spin current produced by the bulk spin Hall effect in the HM [18, 53]. In the case of bilayers, ξDL=θSH\xi_{DL} = \theta_{SH}. We thus obtained θSHPt=10%\theta_{SH}^{Pt} = 10\%, θSHTa=−3.5%\theta_{SH}^{Ta} = -3.5\% which is in agreement with the literature [49, 54]. For the trilayers, however, we are only able to extract the effective spin Hall angle θSHeff\theta_{SH}^{eff}, to which both Pt and Ta contribute. The obtained values yield 20%20\% for Pt/Co/Ta and −13%-13\% for Ta/Co/Pt (see Table I). The lower value for the latter trilayer may be attributed to the Ta oxidation at the substrate interface or due to a lower interface quality. The θSHeff\theta_{SH}^{eff} values obtained for the trilayers in this work are slightly lower than those previously reported (34%34\%) for the same trilayer structures with perpendicularly magnetized Co [48].

Harmonic longitudinal voltage analysis: USMR comparison in bi- and trilayers

After the detailed analysis of the second harmonic Hall voltages, we take a closer look at the second harmonic longitudinal voltages. The corresponding data and fits are shown in Figure 4. We observe a similar behavior as for the transverse case, in which for the samples containing Pt, extrema arise at lower magnetic fields at about φ=45∘\varphi= 45^\circ, 135∘135^\circ, 225∘225^\circ, 315∘315^\circ.

Figure 4. Longitudinal second harmonic resistance for the studied (a), (b) bi- and (c), (d) trilayers with a Hall bar width of w=4μmw = 4\mu\mathrm{m}. Red and light blue circles correspond to the measured data at 1 T and 0.05 T, respectively. The fits (black dashed lines) were performed with the asin⁡φ+b(2cos⁡3φ−cos⁡φ)a\sin\varphi+ b(2\cos^{3}\varphi- \cos\varphi) function.

In order to investigate the influence in a different material with negative θSH\theta_{SH}, but lower resistivity as compared to Ta, two samples with W instead of Ta were prepared. The W samples stacks are: Si/SiO2_2/W 7/Co 2.5/MgO 2/TaOx_x and Si/SiO2_2/W 8/Co 2.5/Pt 6/MgO 2/TaOx_x. These samples have been measured and analyzed in the same manner as the aforementioned Pt and Ta systems. The R2ωR^{2\omega} magnetic field dependence of the Pt and Ta samples is plotted in Figure 5(a). The samples containing W do not show a comparable R2ωR^{2\omega} magnetic field dependence, as shown with magenta and violet stars in Figure 5(b). Following Ref. [36], we fit the data with a c+const⋅B−pc + \mathrm{const}\cdot B^{-p} function (dashed line), with cc being an offset. It is clear, that in the saturated regime, above 0.4 T, there is no dependence on the magnetic field. However, for lower magnetic field strengths (unsaturated state) the effect magnitude varies, although this behavior predominantly appears in Pt samples (blue and turquoise circles, as well as orange squares) with no magnetic field dependence for the Ta/Co bilayer (red squares). This finding confirms that the USMR effect is magnetic field-independent and the only reason for the higher signal amplitudes at lower fields is the FL SOT contribution.

Second harmonic longitudinal resistance dependence on magnetic field for bi- and trilayers

Figure 5. (a) Second harmonic longitudinal resistance dependence on magnetic field for bi- and trilayers with Pt, Ta and W. Dashed lines are fit with the c+const⋅B−pc + \mathrm{const}\cdot B^{-p} function. The orange shaded area encloses the data in unsaturated regime. (b) Zoomed-in region with focus on W samples.

Finally, the USMR is calculated via RUSMR2ω=R2ω−lwRT2ωR^{2\omega}_{USMR} = R^{2\omega} - \frac{l}{w}R^{2\omega}_{T}, with lw=5\frac{l}{w} = 5. A detailed analysis of the RUSMR2ωR^{2\omega}_{USMR} current dependence is shown in Figure 6(a). For further comparison, the values at 1×107 A/cm21 \times10^{7}\ \mathrm{A/cm}^{2} (slope of the linear fit) are discussed. It can be seen that for the Ta-based systems with positive USMR, the bilayer exhibits the highest value of 0.95 mΩ\Omega, while the respective trilayer yields RUSMR2ω=0.23R^{2\omega}_{USMR} = 0.23 mΩ\Omega. In the case of the Pt based samples with negative USMR, the difference between the extracted USMR values is not large (RUSMR2ω=−0.79R^{2\omega}_{USMR} = -0.79 mΩ\Omega vs. RUSMR2ω=−0.66R^{2\omega}_{USMR} = -0.66 mΩ\Omega), however, here, no enhancement for the trilayer is found. First of all, when we explore in more detail the Ta/Co bilayer, Ta in our film stacks has a resistivity 180 μΩ\mu\Omega cm, which is ∼4\sim4-5 times higher than Co (40 μΩ\mu\Omega cm) and, therefore, it is anticipated that most of the charge current flows through the Co layer. The resistivity of Co was taken from the literature for the same thin film thickness [49, 55], while the resistivities of Ta and Pt were calculated using the parallel resistor model with known Co resistivity. Thus, when Pt is added on top, the charge current distribution changes.

Figure 6. (a) USMR dependence on total charge current for bi- and trilayers with Pt and Ta. (b) Normalized USMR dependence on HM charge current density normalized to the HM resistance. Dashed lines are linear fits with fixed zero offset.

sampleRAHER_{AHE} (Ω)RPHER_{PHE} (Ω)BDLB_{DL} (mT)BFL+OeB_{FL+Oe} (mT)ξDL\xi_{DL}ξFL\xi_{FL}RUSMR2ωR_{USMR}^{2\omega} (mΩ)RUSMRRHM×10−5\frac{R_{USMR}}{R_{HM}} \times10^{-5} per 10710^{7} A/cm²
Pt/Co0.350.110.721-0.194∼\sim0.10.0006-0.79-0.26
Ta/Co1.10.12-0.133-0.136∼\sim-0.0350.0130.950.11
Pt/Co/Ta0.230.070.84-0.056∼\sim0.2-0.011-0.66-0.32
Ta/Co/Pt0.240.05-0.710.335∼\sim-0.130.070.230.14

Table 1. A summary of the results for the Pt and Ta systems.

Thus, to correctly compare the USMR effect between the different samples, we take the ratio between the USMR effect RUSMR2ωR_{USMR}^{2\omega} and the HM resistance RHMR_{HM}. In case of the trilayers, with both Pt and Ta present, we calculate the current density flowing through both heavy metals using the parallel resistors model. Figure 6(b) presents the current density dependence of the normalized USMR. We observe an enhancement of the effect in trilayers, of up to 27%. The maximum effect of -0.32 ×10−5\times10^{-5} per 10710^{7} A/cm² is observed in the Pt/Co/Ta trilayer.

When we take a closer look at the bilayers, we see that the weighted USMR effect is stronger for Pt than Ta. Such a behavior can be explained by intermixing at the Ta/Co interface or oxidation of Ta at the substrate. By adding another HM interface to the bilayer, spin current is then driven from both sides into Co, and thus an increase of the USMR effect is achieved.

In case of the W-based samples, both bi- and trilayer show equal values within the uncertainty limit, as compared to the corresponding Ta samples. As was discussed by Pai et al. [56], the θSHW\theta_{SH}^{W} and resistivity strongly depend on the phase, with the highest θSHW\theta_{SH}^{W} value being -33% and resistivity in the range of 100–300 μΩ\mu\Omegacm reported by the authors for the β\beta phase of tungsten. In this work, we determined the W resistivity to be ≈90 μΩ\approx90\ \mu\Omegacm, indicating a mixture of both α\alpha and β\beta phases, thus a lower θSHW\theta_{SH}^{W} is expected.

Conclusions

In summary, we have discussed harmonic voltage measurements of Pt/Co and Ta/Co bilayers, as well as their HM1/Co/HM2 trilayers. By analyzing the 2ω2\omega Hall resistance, we were able to extract the important information about SOTs, as well as spin Hall angle for bilayers. Averaged extracted values of θSHPt≈10%\theta_{SH}^{Pt} \approx10\% and θSHTa=−3.5%\theta_{SH}^{Ta} = -3.5\% are in agreement with previously reported ones. For the trilayers, effective θSHeff\theta_{SH}^{eff} are found to be θSHeff=20%\theta_{SH}^{eff} = 20\% and -13% for the Pt/Co/Ta and Ta/Co/Pt, respectively. Finally, the USMR effect in the studied samples have similar values for bilayers, when compared to the literature. The obtained values for bilayers RUSMR2ω/RHMR_{USMR}^{2\omega}/R_{HM} are -0.26 ×10−5\times10^{-5} and 0.11 ×10−5\times10^{-5} for Pt/Co and Ta/Co, respectively. For trilayers, we observe a modest enhancement, with RUSMR2ω/RHMR_{USMR}^{2\omega}/R_{HM} found to be -0.32 ×10−5\times10^{-5} for Pt/Co/Ta and 0.14 ×10−5\times10^{-5} for Ta/Co/Pt samples per 10710^{7} A/cm², respectively. Additionally, two samples with W instead of Ta were measured, to compare the USMR effect size, as W is expected to have lower resistivity and higher negative spin Hall angle. The obtained USMR values for these samples, however, are equal to Ta-based systems within the uncertainty limit, thus no increase in USMR is observed. This is contrary to the expectations, but can be linked to the W-phase and film oxidation. These factors when combined can lead to the higher resistivity values, comparable to those of Ta.

Acknowledgments

The authors thank Daniel Carsten for help with initial experiments. We further thank Markus Meinert, Johannes Mendil and Pietro Gambardella for valuable discussions and comments. Finally, we thank Tristan Matalla-Wagner and Jan Biedinger for help with VSM and AGM measurements.

References

  1. [1]D. Sander, S. O. Valenzuela, D. Makarov, C. H. Mar- rows, E. E. Fullerton, P. Fischer, J. McCord, P. Vavas- sori, S. Mangin, P. Pirro, B. Hillebrands, A. D. Kent, T. Jungwirth, O. Gutfleisch, C. G. Kim, and A. Berger, The 2017 magnetism roadmap, J. Phys. D: Appl. Phys. 50, 363001 (2017).
  2. [2]C. Zheng, K. Zhu, S. Cardoso de Freitas, J.-Y. Chang, J. E. Davies, P. Eames, P. P. Freitas, O. Kazakova, C. Kim, C.-W. Leung, S.-H. Liou, A. Ognev, S. N. Piramanayagam, P. Ripka, A. Samardak, K.-H. Shin, S.-Y. Tong, M.-J. Tung, S. X. Wang, S. Xue, X. Yin, and P. W. T. Pong, Magnetoresistive sensor development roadmap (non-recording applications), IEEE Trans. Magn. 55, 0800130 (2019).DOI
  3. [3]S. Ikeda, J. Hayakawa, Y. M. Lee, F. Matsukura, Y. Ohno, T. Hanyu, and H. Ohno, Magnetic tunnel junctions for spintronic memories and beyond, IEEE Trans. Electron Devices 54, 991 (2007).
  4. [4]H. Cai, W. Kang, Y. Wang, L. Naviner, J. Yang, and W. Zhao, High performance MRAM with spin-transfer-torque and voltage-controlled magnetic anisotropy effects, Appl. Sci. 7, 929 (2017).DOI
  5. [5]C. Reig, M.-D. Cubells-Beltrán, and D. Ramírez Muñoz, Magnetic field sensors based on giant magnetoresistance (GMR) technology: Applications in electrical current sensing, Sensors 9, 7919–7942 (2009).
  6. [6]H. Nakayama, M. Althammer, Y.-T. Chen, K. Uchida, Y. Kajiwara, D. Kikuchi, T. Ohtani, S. Geprägs, M. Opel, S. Takahashi, R. Gross, G. E. W. Bauer, S. T. B. Goennenwein, and E. Saitoh, Spin Hall magnetoresistance induced by a nonequilibrium proximity effect, Phys. Rev. Lett. 110, 206601 (2013).
  7. [7]N. Vlietstra, J. Shan, V. Castel, B. J. van Wees, and J. B. Youssef, Spin-Hall magnetoresistance in platinum on yttrium iron garnet: Dependence on platinum thickness and in-plane/out-of-plane magnetization, Phys. Rev. B 87, 184421 (2013).DOI
  8. [8]Y.-T. Chen, S. Takahashi, H. Nakayama, M. Althammer, S. T. B. Goennenwein, E. Saitoh, and G. E. W. Bauer, Theory of spin Hall magnetoresistance, Phys. Rev. B 87, 144411 (2013).
  9. [9]M. Althammer, S. Meyer, H. Nakayama, M. Schreier, S. Altmannshofer, M. Weiler, H. Huebl, S. Geprägs, M. Opel, R. Gross, D. Meier, C. Klee, T. Kuschel, J.-M. Schmalhorst, G. Reiss, L. Shen, A. Gupta, Y.-T. Chen, G. E. W. Bauer, E. Saitoh, and S. T. B. Goennenwein, Quantitative study of the spin Hall magnetoresistance in ferromagnetic insulator/normal metal hybrids, Phys. Rev. B 87, 224401 (2013).
  10. [10]J. Kim, P. Sheng, S. Takahashi, S. Mitani, and M. Hayashi, Spin Hall magnetoresistance in metallic bilayers, Phys. Rev. Lett. 116, 097201 (2016).
  11. [11]A. Philippi-Kobs, A. Farhadi, L. Mathes, D. Lott, A. Chuvilin, and H. Oepen, Impact of symmetry on anisotropic magnetoresistance in textured ferromagnetic thin films, Phys. Rev. Lett. 123, 137201 (2019).
  12. [12]L. Karwacki, K. Grochot, S. Łazarski, W. Skowroński, J. Kanak, W. Powroźnik, J. Barnaś, F. Stobiecki, and T. Stobiecki, Optimization of spin Hall magnetoresistance in heavy-metal/ferromagnetic-metal bilayers, Sci. Rep. 10, 10767 (2020).
  13. [13]M. Dyakonov and V. Perel, Current-induced spin orientation of electrons in semiconductors, Phys. Lett. A 35, 459 (1971).
  14. [14]J. E. Hirsch, Spin Hall effect, Phys. Rev. Lett. 83, 1834 (1999).
  15. [15]Y. K. Kato, R. R. Myers, A. C. Gossard, and D. D. Awschalom, Observation of the spin Hall effect in semiconductors, Science 306, 1910 (2004).
  16. [16]A. Hoffmann, Spin Hall effects in metals, IEEE Trans. Magn. 49, 5172 (2013).
  17. [17]I. M. Miron, K. Garello, G. Gaudin, P.-J. Zermatten, M. V. Costache, S. Auffret, S. Bandiera, B. Rodmacq, A. Schuhl, and P. Gambardella, Perpendicular switching of a single ferromagnetic layer induced by in-plane current injection, Nature (London) 476, 189 (2011).
  18. [18]L. Liu, C.-F. Pai, Y. Li, H. Tseng, D. Ralph, and R. Buhrman, Spin-torque switching with the giant spin Hall effect of tantalum, Science 336, 555 (2012).
  19. [19]A. Manchon, J. Železný, I. M. Miron, T. Jungwirth, J. Sinova, A. Thiaville, K. Garello, and P. Gambardella, Current-induced spin-orbit torques in ferromagnetic and antiferromagnetic systems, Rev. Mod. Phys. 91, 035004 (2019).
  20. [20]K. Chi, Y. Shi, Z. Li, W. Zhang, Y. Xing, X. Feng, Y. Ma, H. Meng, and B. Liu, L-shaped electrode design for high-density spin-orbit torque magnetic random access memory with perpendicular shape anisotropy, J. Phys. D: Appl. Phys. 54, 285002 (2021).
  21. [21]H. Sun, L. Cheng, J. Xu, C. Yu, H. Xiao, R. Wang, L. Xu, Z. Zeng, and S. Liang, Current-induced spin-orbit torque magnetization switching with considering unconventional staggered spin polarization, J. Magn. Magn. Mater. 530, 167906 (2021).
  22. [22]D. Ralph and M. Stiles, Spin transfer torques, J. Magn. Magn. Mater. 320, 1190 (2008).
  23. [23]E. Grimaldi, V. Krizakova, G. Sala, F. Yasin, S. Couet, G. S. Kar, K. Garello, and P. Gambardella, Single-shot dynamics of spin–orbit torque and spin transfer torque switching in three-terminal magnetic tunnel junctions, Nat. Nanotechnol. 15, 111 (2020).
  24. [24]I. Ahmed, Z. Zhao, M. G. Mankalale, S. S. Sapatnekar, J. P. Wang, and C. H. Kim, A comparative study between spin-transfer-torque and spin-Hall-effect switching mechanisms in PMTJ using SPICE, IEEE J. Explor. Solid-State Computat. 3, 74 (2017).
  25. [25]W. Cai, K. Shi, Y. Zhuo, D. Zhu, Y. Huang, J. Yin, K. Cao, Z. Wang, Z. Guo, Z. Wang, G. Wang, and W. Zhao, Sub-ns field-free switching in perpendicular magnetic tunnel junctions by the interplay of spin transfer and orbit torques, IEEE Electron Device Lett. 42, 704 (2021).
  26. [26]X. Qiu, K. Narayanapillai, Y. Wu, P. Deorani, D.-H. Yang, W.-S. Noh, J.-H. Park, K.-J. Lee, H.-W. Lee, and H. Yang, Spin-orbit-torque engineering via oxygen manipulation, Nat. Nanotechn. 10, 333 (2015).
  27. [27]Y. Hibino, T. Hirai, K. Hasegawa, T. Koyama, and D. Chiba, Enhancement of the spin-orbit torque in a Pt/Co system with a naturally oxidized Co layer, Appl. Phys. Lett. 111, 132404 (2017).
  28. [28]K. Hasegawa, Y. Hibino, M. Suzuki, T. Koyama, and D. Chiba, Enhancement of spin-orbit torque by inserting CoOx layer into Co/Pt interface, Phys. Rev. B 98, 020405(R) (2018).
  29. [29]J. Feng, E. Grimaldi, C. O. Avci, M. Baumgartner, G. Cossu, A. Rossi, and P. Gambardella, Effects of oxidation of top and bottom interfaces on the electric, magnetic, and spin-orbit torque properties of Pt/Co/AlOx trilayers, Phys. Rev. Appl. 13, 044029 (2020).
  30. [30]X. Feng, J. Yao, Y. Cui, P. Zhang, Q. Bai, L. Xi, J. Cao, D. Xue, and X. Fan, Impact of trace amounts of interfacial oxidation on the spin–orbit torque in the Co/Pt heterostructures, Appl. Phys. Lett. 118, 132410 (2021).
  31. [31]A. Anadón, R. Guerrero, J. A. Jover-Galtier, A. Gudín, J. M. Díez Toledano, P. Olleros-Rodríguez, R. Miranda, J. Camarero, and P. Perna, Spin-orbit torque from the introduction of Cu interlayers in Pt/Cu/Co/Pt nanolayered structures for spintronic devices, ACS Appl. Nano Mater. 4, 487 (2021).
  32. [32]S. Ding, A. Ross, D. Go, L. Baldrati, Z. Ren, F. Freimuth, S. Becker, F. Kammerbauer, J. Yang, G. Jakob, Y. Mokrousov, and M. Kläui, Harnessing orbital-to-spin conversion of interfacial orbital currents for efficient spin-orbit torques, Phys. Rev. Lett. 125, 177201 (2020).
  33. [33]C. O. Avci, K. Garello, A. Ghosh, M. Gabureac, S. F. Alvarado, and P. Gambardella, Unidirectional spin Hall magnetoresistance in ferromagnet/normal metal bilayers, Nat. Phys. 11, 570 (2015).
  34. [34]S. S. Zhang and G. Vignale, Theory of unidirectional spin Hall magnetoresistance in heavy-metal/ferromagnetic-metal bilayers, Phys. Rev. B 94, 140411(R) (2016).
  35. [35]I. V. Borisenko, V. E. Demidov, S. Urazhdin, A. B. Rinkevich, and S. O. Demokritov, Relation between unidirectional spin Hall magnetoresistance and spin current-driven magnon generation, Appl. Phys. Lett. 113, 062403 (2018).
  36. [36]C. O. Avci, J. Mendil, G. S. D. Beach, and P. Gambardella, Origins of the unidirectional spin Hall magnetoresistance in metallic bilayers, Phys. Rev. Lett. 121, 087207 (2018).
  37. [37]W. P. Sterk, D. Peerling, and R. A. Duine, Magnon contribution to unidirectional spin Hall magnetoresistance in ferromagnetic-insulator/heavy-metal bilayers, Phys. Rev. B 99, 064438 (2019).
  38. [38]C. O. Avci, M. Mann, A. J. Tan, P. Gambardella, and G. S. Beach, A multi-state memory device based on the unidirectional spin Hall magnetoresistance, Appl. Phys. Lett. 110, 203506 (2017).
  39. [39]K. Olejnik, V. Novak, J. Wunderlich, and T. Jungwirth, Electrical detection of magnetization reversal without auxiliary magnets, Phys. Rev. B 91, 180402 (R) (2015).
  40. [40]Y. Lv, J. Kally, D. Zhang, J. S. Lee, M. M. Jamali, N. Samarth, and J.-P. Wang, Unidirectional spin-Hall and Rashba-Edelstein magnetoresistance in topological insulator-ferromagnet layer heterostructures, Nat. Commun. 9, 111 (2018).
  41. [41]C. Lidig, J. Cramer, L. Weißhoff, T. Thomas, T. Kessler, M. Kläui, and M. Jourdan, Unidirectional spin Hall magnetoresistance as a tool for probing the interfacial spin polarization of Co2MnSi, Phys. Rev. Appl. 11, 044039 (2019).
  42. [42]Y. Yin, D. S. Han, M. C. De Jong, R. Lavrijsen, R. A. Duine, H. J. Swagten, and B. Koopmans, Thickness dependence of unidirectional spin-Hall magnetoresistance in metallic bilayers, Appl. Phys. Lett. 111, 232405 (2017).
  43. [43]K. Hasegawa, T. Koyama, and D. Chiba, Enhanced unidirectional spin Hall magnetoresistance in a Pt/Co system with a Cu interlayer, Phys. Rev. B 103, L020411 (2021).
  44. [44]W. Zhang, M. B. Jungfleisch, W. Jiang, Y. Liu, J. E. Pearson, S. G. E. te Velthuis, A. Hoffmann, F. Freimuth, and Y. Mokrousov, Reduced spin-Hall effects from magnetic proximity, Phys. Rev. B 91, 115316 (2015).
  45. [45]T. A. Peterson, A. P. McFadden, C. J. Palmstrøm, and P. A. Crowell, Influence of the magnetic proximity effect on spin-orbit torque efficiencies in ferromagnet/platinum bilayers, Phys. Rev. B 97, 020403 (2018).
  46. [46]L. J. Zhu, D. C. Ralph, and R. A. Buhrman, Irrelevance of magnetic proximity effect to spin-orbit torques in heavy-metal/ferromagnet bilayers, Phys. Rev. B 98, 134406 (2018).
  47. [47]A. Moskaltseva, J. Krieft, D. Graulich, T. Matalla-Wagner, and T. Kuschel, Impact of the magnetic proximity effect in Pt on the total magnetic moment of Pt/Co/Ta trilayers studied by x-ray resonant magnetic reflectivity, AIP Advances 10, 015154 (2020).
  48. [48]S. Woo, M. Mann, A. J. Tan, L. Caretta, and G. S. Beach, Enhanced spin-orbit torques in Pt/Co/Ta heterostructures, Appl. Phys. Lett. 105, 212404 (2014).
  49. [49]C. O. Avci, K. Garello, M. Gabureac, A. Ghosh, A. Fuhrer, S. F. Alvarado, and P. Gambardella, Interplay of spin-orbit torque and thermoelectric effects in ferromagnet/normal-metal bilayers, Phys. Rev. B 90, 224427 (2014).
  50. [50]Y. C. Lau and M. Hayash, Spin torque efficiency of Ta, W, and Pt in metallic bilayers evaluated by harmonic Hall and spin Hall magnetoresistance measurements, Jpn. J. Appl. Phys. 56, 0802B5 (2017).
  51. [51]L. Neumann and M. Meinert, Influence of the Hall-bar geometry on harmonic Hall voltage measurements of spin-orbit torques, AIP Advances 8, 095320 (2018).
  52. [52]A. V. Khvalkovskiy, V. Cros, D. Apalkov, V. Nikitin, M. Krounbi, K. A. Zvezdin, A. Anane, J. Grollier, and A. Fert, Matching domain-wall configuration and spin-orbit torques for efficient domain-wall motion, Phys. Rev. B 87, 020402(R) (2013).
  53. [53]C. O. Avci, K. Garello, J. Mendil, A. Ghosh, N. Blasakis, M. Gabureac, M. Trassin, M. Fiebig, and P. Gambardella, Magnetoresistance of heavy and light metal/ferromagnet bilayers, Appl. Phys. Lett. 107, 192405 (2015).
  54. [54]E. Sagasta, Y. Omori, M. Isasa, M. Gradhand, L. E. Hueso, Y. Niimi, Y. Otani, and F. Casanova, Tuning the spin Hall effect of Pt from the moderately dirty to the superclean regime, Phys. Rev. B 94, 060412(R) (2016).
  55. [55]M. Siniscalchi, D. Tierno, K. Moors, Z. Tökei, and C. Adelmann, Temperature-dependent resistivity of alternative metal thin films, Appl. Phys. Lett. 117, 043104 (2020).
  56. [56]C. F. Pai, L. Liu, Y. Li, H. W. Tseng, D. C. Ralph, and R. A. Buhrman, Spin transfer torque devices utilizing the giant spin Hall effect of tungsten, Appl. Phys. Lett. 101, 122404 (2012).

Paper details

vlnc:W_c9z8rjht
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 8

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents