WorksPhysics and Astronomy
Fluid drags on a sphere at finite Reynolds number–a classical problem examined afresh
Abstract
Evaluating the drag coefficient Cd for a sphere moving in a fluid at finite Reynolds number Re has become a classical research subject in fluid dynamics, with publications appearing continuously by numerous authors over the years due to the unavailability of closed-form mathematical solutions. To date, mathematical formulas for calculating Cd as a function of Re can only be obtained by correlation curve fitting to experimental data. The consequence is the coexistence of various formulas with different mathematical fitting functions and an increasing number of fitting parameters. The present study focuses on examining the accuracy of Klyachko's 1934 formula for Cd with two common fractions as fitting parameters, which could enable closed form integration of a simplified equation governing rectilinear motion of aerosol spheres. The computed values of root-mean-square relative error from recently developed formulas show reasonable accuracy of the Klyachko formula for Re less than 1000 and its extension to Re less than 2e5 as a piecewise continuous function, with the possibility of significant improvement through a slight modification. Hence, a few demonstrative examples are presented using the extended Klyachko formula in the study of rectilinear acceleration, the calculation of the terminal velocity of aerosol spheres, and so forth, to shed fresh light on how this classical problem can be studied.
Introduction
As a fundamental canonical problem in fluid mechanics, flow past a sphere has been studied by numerous authors and discussed in well-known subject-matter books [14, 22, 15, 8, 6 Pruppacher] and Klett, 1997). Besides its theoretical convenience for the in-depth mathematical study of drag, boundary layer separation, and turbulence, the problem of a spherical body moving in a fluid often appears in a myriad of natural processes and engineering applications [8, 6, 18]. Despite the tremendous efforts by generations after generations of mathematically talented scientists, closed-form analytical solutions for flow around rigid and fluid spheres are effectively limited to very low values of the Reynolds number, (where denotes the sphere’s diameter, and the relative velocity and kinematic viscosity of the surrounding fluid). Knowledge about the situation at higher Reynolds numbers must resort to experimental measurements, numerical computations, as well as approximations based on boundary-layer theory [6].
Dictated by the laws of physics, a sphere (or any object of another shape) will experience a drag force—as the surface integral over its whole surface of all stresses arising from the relative fluid flow—whenever there is a relative motion of it in the surrounding fluid [15]. In scientific literature, a dimensionless version of the drag force—the drag coefficient (with denoting the drag force and the density of surrounding fluid)—has commonly been utilized for convenience of analytical description [22, 15, 8, 6, 18, 20, 9, 17].
The drag coefficient of a sphere in steady motion, in an incompressible Newtonian fluid, is often presented as a graph versus known as the ”Rayleigh curve” or “standard drag curve” [6], which has been expressed in terms of mathematical functions with adjustable fitting parameters by various authors via empirical or semiempirical means with persistent correlation efforts [e.g. 21, 12, 16, 4, 5], including the usage of a genetic programming procedure [2] and machine learning with a symbolic regression algorithm [11]. In view of the Cheng [5] comparisons with compiled experimental data from multiple sources, the reported values of the “average relative error” of correlation formulas from different authors, with vastly different mathematical complexities, are mostly within , e.g., 3.019% of Clift, Grace, and Weber [6], 3.236% of Brown and Lawler [4], 2.469% of Cheng [5]. and so on so forth.
Valuable as it might be for a percent or so improvement in the correlation relative error, publications by many recent authors [4, 5, 2, 13, 11] seem to focus only on sophisticated correlation formulas, often expressed in terms of transcendental functions with increasing number of the fitting parameters, for , while completely omitting (or no more than barely mentioning) the much cleaner formula with only two fitting parameters, , suggested by Schiller and Naumann [21] (with and ), Klyachko [12] (with common fractions and ), among others. According to Fuchs [8], the Klyachko formula appears quite accurate, agreeing with the experimental data at least for (whereas Klyachko [12] applied it for ).
Interestingly, a formula very similar to that of Klyachko (with only the parameter replaced by 0.158) was adopted by Serafini [23] (who claimed to agree with experimental values for but without citing the previous work of Klyachko), in the derivation of a closed-form analytical solution. Later, Putnam (1961) extended the validity of the Klyachko formula to (also without citing prior publications by either Klyachko or Serafini), when demonstrating the existence of an analytical solution (which had already been used by Klyachko in 1934). What has been implemented in the computational fluid dynamics (CFD) software package OpenFOAM® for the “sphere drag” calculation is in terms of a piecewise continuous function
following the KIVA-II work of Amsden, O’Rourke, and Butler [1] (which would actually be invalid beyond when the abrupt “drag crisis” occurs). It is effectively an extension of the Klyachko formula for up to (though Klyachko suggested as the extension upper limit, which is realistically over-aggressive and should be ignored) by continuously connecting it to a constant of at , where the value of is chosen as 1000 by Amsden et al. in (1).
The mathematical function of (1) for , though significantly nonlinear, was shown to enable the derivation of a closed-form analytical solution to the differential equation governing the rectilinear motion of a sphere in a fluid [23, 19], when forces (such as added mass and Basset-Boussinesq history force) other than the steady-flow drag are negligible, such as situations often encountered with aerosol particles [8]. A closed-form analytical solution in fluid dynamics of a moving sphere is generally considered intractable, and highly appreciated for its mathematical elegance even though it is useful only for special circumstances in a limited interval of values. Therefore, it deserves special attention in the scientific community.
In what follows, we start by examining the numerical differences between (1) and those of the more recent formulas, to shed light on how good (or bad) the extended Klyachko formula can be, thereby closing a knowledge gap in the scientific literature. Then, a few examples are presented for practical applications using the given by (1) or its improved version.
Comparison of with a reference formula
To measure the difference (or “error”) between the extended Klyachko formula (1) and a recently developed correlation formula, such as that of Brown and Lawler [4] or others, the root-mean-square relative error (RMSRE):
is used here, where denotes the test function and the reference function.
Table 1 presents the values of RMSRE (2) with for the in (1) and the reference function for the correlation formulas for 480 points “subcritical” experimental data for by recent authors, i.e.,
by Brown and Lawler [4],
by Cheng [5],
by Barati, Neyshabouri, and Ahmadi [2], integrated from to , 900, 800, and 500 as well as to . Apparently, for , the RMSRE value is consistently lowest for (1) versus the correlation formula of Cheng [5], while the differences between (1) and all three correlation formulas of Brown and Lawler [4], Cheng [5], and Barati, Neyshabouri, and Ahmadi [2] have RMSRE values less than 5%. Most of the differences appear to come from the interval of , because a close examination shows that (1) exhibits a gradual deviation from the “standard curve” of versus for up to by almost 8% underestimation around where has been consistently measured in experiments. But for (where the experimental data vary from in to in ), the RMSRE values for the simple approximation versus those of the sophisticated correlation formulas become slightly over 10%, coming mostly from the interval of . Nonetheless, these few percentage points of differences between (1) and more recent correlation formulas appear quite insignificant when viewed in the graph of Figure 1 (where the relatively low RMSRE case of Cheng is omitted without loss of illustrative effectiveness).
Figure 1. Graphic comparison between Klyachko’s formula expressed as Eq. (1) and more recent correlation formulas for drag coefficient [4, 2]
It should be noted that Table 1 also reveals the fact that a significant reduction of the RMSRE values can be achieved by simply moving the upper limit of the Klyachko formula in (1) from to 900, for a modified formula with improved accuracy (especially for up to with the constant value of for effectively increased from 0.424 to ),
| interval | Brown and Lawler | Cheng | Barati et al. |
| 0.0434 | 0.0411 | 0.0464 | |
| 0.0373 | 0.0332 | 0.0396 | |
| 0.0315 | 0.0256 | 0.0337 | |
| 0.0198 | 0.0112 | 0.0285 | |
| 0.0753 | 0.0711 | 0.0734 | |
| 0.1109 | 0.1206 | 0.1155 | |
| 0.0539 | 0.0466 | 0.0525 | |
| 0.0529 | 0.0586 | 0.0562 |
Table 1. RMSRE values for of Klyachko’s formula expressed as Eq. (1) versus that obtained by Brown and Lawler [4], Cheng [5], and Barati, Neyshabouri, and Ahmadi [2].
As a comparative reference, the RMSRE values calculated for Brown and Lawler versus Barati et al. and Cheng versus Barati et al. in the interval from to 1000 are and 0.0161, respectively. Obviously, a few percent of disagreements among even those recent correlation formulas appear inevitable. Thus, the accuracy of either (1) or (3) can be quite acceptable.
In view of numerical differences among various available correlation formulas and the noisiness of experimental data, the comparison between (1) and recently developed “more accurate” correlation formulas appears quite reasonable for practical real-world applications, especially for . The “accuracy” of (1) is shown here to further improve with a slight intuitive modification like (3),
There seems to be no agreed-upon best metric for evaluating the correlation accuracy; different authors sometimes choose different sets of metrics in presenting correlation results. Even when RMSRE is used, the formula (2) is but just one form for straightforward calculations, while it can have a corresponding discrete version as:
the value of which could be sensitive to how those data points are distributed. If so desired, those data points can be evenly distributed in a logarithmic scale of as shown in Figure 1 for discrete points of “Brown and Lawler” and “Barati et al.” Then, the discrete RMSRE values of in become 0.0290, 0.0345, 0.0375 for (1) versus “Brown and Lawler”, “Cheng”, “Barati et al.”, respectively. For in , those discrete RMSRE values are 0.0685, 0.0608, 0.0687. Despite slight numerical variations, whether to use (2) or its discrete version does not seem to make a fundamental difference in the present case when comparing (1) with other correlation formulas.
In terms of the discrete RMSRE, the value for the Brown and Lawler formula versus their set of compiled experimental data is calculated as 0.0411, and that for the Cheng formula as 0.0346. On the other hand, [4, 5, 2] also presented their correlation results using the same set of experimental data in terms of the “average relative error”, , calculated as 0.0324, 0.0247, 0.0223. No matter which metric is employed, the apparent accuracy improvements over the years seem to have approached their limit, differing by no more than a few percent from inevitably noisy experimental data. Therefore, those recent correlation formulas can be reasonably regarded as trustworthy surrogates for the actual experimental data.
Particle rectilinear acceleration
For the case of quasistatic drag as the only dominant force controlling the rectilinear motion of a spherical particle (with particle density and velocity ), Newton’s law of motion based on (3) for the “initial particle Reynolds number” can be written as
where and .
For the case of , a straightforward integration of (4a) for yields
Then, for , it turns out (though may not be immediately obvious) that (4b) can be rearranged as
which yields an analytical solution for , similar to that shown by Serafini [23] and Putnam [19] (equivalent to the case of such that and ),
where and
As Serafini [23] pointed out, it is the exponent in (4b) that enables closed-form integration. (In other words, the formula of Schiller and Naumann [21], though very similar to that of Klyachko in mathematical form but with an exponent slightly deviating from , cannot facilitate a closed-form integration in a rigorous sense.)
By integrating given by (5) from 0 to (if for ) and (6) from to (when ), the particle flight distance (in units of ) as a function of flight time can also be derived as
Then, the stop distance (namely, the maximum achievable flight distance as ), often used to evaluate possible nozzle-to-substrate standoff in drop-on-demand inkjet printing for an ejected droplet, when becomes
For the case of , we should have replaced by 1 and . Thus (8) can be written as Serafini, [23]; Putnam [19]
because .
It should be noted that (4) and subsequent analytical formulas (5)-(9) are valid only when (as in the case of aerosols), such that the effects of time-dependent components of drag (such as added mass and Basset-Boussinesq history force included in the discussion of Landau and Lifshitz, 1959 as well as Fuchs, 1964) are negligible, and also when the effect of gravity could be ignored, i.e., the terminal velocity due to gravity is much smaller than the sphere velocity magnitude of interest, as in the study of dust particles in dust-recollecting devices Klyachko, [12], droplet impingement onto an airfoil Serafini, [23], fuel droplet spray in a combustion chamber [19, 1], among others.
Particle terminal settling velocity
With a given for a sphere moving in a fluid, the terminal velocity of a spherical particle with density settling under the influence of gravity can be readily calculated based on force balance:
where denotes gravitational acceleration. Noteworthy here is that is the Archimedes number (also called the Best number), while is known as the Davies number, often used by atmospheric scientists in studying the terminal velocity of water droplets in air [7, 3].
If the particle diameter and velocity are nondimensionalized as
we have as suggested by Brown and Lawler [4].
With given by (1) or (3), and can be easily calculated as functions of , as
and then ,
where we have with (1) or with (3), if so chosen.
However, most authors present curve-fitting formulas for directly calculating the terminal velocity from a given particle size, namely, [4, 5]. In view of the fact that and as functions of , (11a) is equivalent to and (11b) , none of which could readily be converted to an explicit function of . If (11) and (12) are used as a parametric representation for generating tabulated data or plot, complicated numerical inversion can be avoided. Occasionally though, explicit solutions of can be obtained when a very simplified form of was adopted, like that used by Zigrang and Sylvester [25], or the formula of (12) for which yields
e.g., for or for where the difference seems negligible with either choice.
Obviously, calculating and from a given according to (12) can be much more straightforward and less cumbersome; only a mindset is needed here for the calculation procedure starting with a given value of . In generating a lookup table or graph of versus for practical usage, which calculation procedure to follow usually does not make any difference.
Table 2 and figure 2 exemplify tabulated values of , generated based on (12) for in comparison with the correlation formulas:
by Brown and Lawler [4],
| Brown and Lawler | Cheng | |||
| 0.01 | 0.56607 | 0.017666 | 0.0190347 | 0.0177829 |
| 0.03 | 0.818670 | 0.036645 | 0.0392648 | 0.0371126 |
| 0.1 | 1.23083 | 0.081246 | 0.0856651 | 0.0832422 |
| 0.3 | 1.79705 | 0.166941 | 0.172253 | 0.173591 |
| 1 | 2.75892 | 0.362460 | 0.365645 | 0.380909 |
| 3 | 4.17400 | 0.718734 | 0.720300 | 0.743474 |
| 10 | 6.83454 | 1.463156 | 1.494056 | 1.454615 |
| 30 | 11.21065 | 2.676026 | 2.813076 | 2.629949 |
| 100 | 20.21706 | 4.946319 | 5.226117 | 5.001796 |
| 300 | 35.76093 | 8.389044 | 8.438702 | 8.609237 |
| 1000 | 68.25624 | 14.65067 | 13.15452 | 14.07184 |
| 3000 | 141.9782 | 21.13000 | 20.23183 | 21.4360 |
| 316.8163 | 31.56403 | 31.10793 | 31.49032 | |
| 659.0044 | 45.52321 | 45.33656 | 44.28541 | |
| 1470.531 | 68.00265 | 68.03615 | 65.02726 |
Table 2. Parametrically calculated values of and based on Eq. (13) for from given compared with the correlation formulas of obtained by Brown and Lawler [4], and Cheng [5].
by Cheng [5], and the corresponding graph of versus . Again not surprisingly, the results of given by (12) for , based on as a slightly less accurate formula (1), are still in reasonable agreement with those of more recent correlation formulas.
One of the most studied cases of terminal velocity is a water droplet falling in air, with , , and , because of its direct relevance to cloud physics and rainfall rate in meteorology. Thus, we have (mm) and (m/s), according to (11a) and (11b). For example, at (or 70), eq. (12) yields (or 16.90) corresponding to (or 0.51) mm, and (or ) with (or 2.06) m/s, fairly close to the measured values tabulated by Gunn and Kinzer [10], e.g., for (or 0.5) mm, (or 2.06) m/s with calculated (or 68.7).
Another important problem closely related to terminal velocity is the dynamical process of the acceleration of a sphere toward its terminal velocity, often needed for evaluating the required free fall length in an experimental setup (Wang and Pruppacher [24]), among other applications. Similar to that with (4), assuming quasistatic drag but with the addition of a term representing the gravitational force in the equation for rectilinear motion (for ):

Figure 2. Graphic comparison between parametrically calculated versus based on Eq. (13) for and more recent correlation formulas of by Brown and Lawler [4] and Cheng [5]
denoting the particle Reynolds number for terminal velocity , where is the sphere diameter, with and . Here,
reflects the fact of gravitational-force-driven motion.
Although differing from (4) only by a constant term, (13) does not admit a closed-form analytical solution. However, it would not be difficult to compute numerical solutions of by 4th-order Runge-Kutta integration of (13), and then by integration of , from 0 to , for generating results for (in units of ) versus (in units of ).
In the case of , (13) needs to be rewritten as
where (17) for leads to an analytical solution
Here, the value of is determined by numerically integrating (16) with respect to until . Thus, at we have .
Integrating the of (18) from to yields the particle flight distance
Because , an analytical formula explicitly relating to (or to ) can also be obtained, for when , based on (17), e.g.,
where the value of should be determined by numerical integration of (16) from to though.
Figure 3 provides but one graphic example of versus for , , and (for ), corresponding to , , and mm of spherical particles of density falling in air with terminal velocity , 3.96, and 7.18 m/s, agreeing well with experimental data for water droplets falling in air [10, 3], especially for mm when droplet deformations are negligible.

Figure 3. Graphic display of versus generated by numerically integrating (14), for and (when ), and (15), for , and then integrating for
In a strictly theoretical sense, it takes infinite time and length for a particle to reach its terminal velocity. But evaluating a finite falling length for to reach 0.99 or 0.95, sometimes denoted as or , could be more useful for practical applications [24]. Thus, in the present context (for , 270, and 1000), we have , 3765.22, and 5092.97, corresponding to , 3.85, and 10.64 m (for spherical particles of , 1.02, and 2.09 mm of density ). As expected, the computed values of here for mm are in good agreement with those presented by Wang and Pruppacher [24] shown with a curve plotted in their Fig. 3 for and 1 mm, and 4 m. If is practically acceptable, we could have considerably reduced fall distances for measurement setups, as , 2.24, and 6.46 m (corresponding to , 2195.26, and 3092.04). Apparently, we have in this case.
Summary
Out of scientific curiosity about the less-known 1934 Klyachko formula for the sphere drag coefficient, which exhibits an exceptionally clean mathematical expression, an overdue relative-error evaluation is performed by comparing it with more recent correlation formulas, for quantitatively understanding how good (or bad) this early curve-fitting formula, as well as its extension to the Reynolds number as a piecewise continuous function, can be for practical applications. The results indicate quantitatively rather insignificant differences between the extended Klyachko formula and other apparently more sophisticated correlation formulas, for (or, better yet, for ).
Once the confidence is established for its reasonable accuracy, the extended Klyachko formula is briefly shown, similar to Serafini [23] and Putnam [19], to yield closed-form analytical solutions (covering the applicable range of ) for the study of rectilinear acceleration of aerosol spheres, when the effect of gravity can be ignored. Then, a demonstration of using the extended Klyachko formula is presented for conveniently calculating the spherical particle diameter and terminal settling velocity as functions of , yielding results in good agreement with recent correlation formulas of Brown and Lawler [4] and Cheng [5]. As expected, the dynamical process of an aerosol sphere accelerating toward its terminal velocity can also be described by solutions of ordinary differential equations based on the extended Klyachko formula, with comparable results to such relevant data of Wang and Pruppacher [24] for water droplet falling in air when droplet deformations are negligible. These demonstrative examples are expected to enhance confidence in the extended Klyachko formula for conveniently studying the classical problem of aerosol (sphere) dynamics, among other applications. The derived closed-form analytical formulas can also be applied in modern CFD code development and validation.
Acknowledgments
The author would like to thank Prof. Rodney Kubesh (of St. Cloud State University) for helpful discussions and Prof. Carlos Ramírez (of University of Puerto Rico) for providing a copy of the original 1934 Russian article by Klyachko.
Funding
None
Ethics declarations
Conflict of interests
The author has no conflicts to declare
ORCID iD
James Q Feng 0000-0003-4041-3179
References
- [1]Amsden, A A, P J O’Rourke, and T D Butler (1989). KIVA-II: A computer program for chemically reactive flos with sprays. Tech. rep. LA-11560-MS; ON: DE89012805. Los Alamos National Lab.DOI
- [2]Barati, R, S A A S Neyshabouri, and G Ahmadi (2014). “Development of empirical models with high accuracy for estimation of drag coefficient of flow around a smooth sphere: An evolutionary approach”. Powder Technol. 257, pp. 11–19. DOI: 10.1016/j.powtec.2014.02.045.DOI
- [3]Beard, K V (1976). “Terminal velocity and shape of cloud and precipitation drops aloft”. J. Atmos. Sci. 33.5, pp. 851–864. DOI: 10.1175/1520-0469(1976)033<0851:TVASOC>2.0.CO.doi.org/10.1175/1520-0469(1976)033<0851:tvasoc>2.0.co;2
- [4]Brown, P P and D F Lawler (2003). “Sphere drag and setting velocity revisited”. J. Environ. Eng. 129.3, pp. 222–231. DOI: 10.1061/(ASCE)0733-9372(2003)129:3(222).DOI
- [5]Cheng, N-S (2009). “Comparison of formulas for drag coefficient and settling velocity of spherical particles”. Powder Technol. 189, pp. 395–398. DOI: 10.1016/j.powtec.2008.07.006.DOI
- [6]Clift, R, J R Grace, and M E Weber (1978). Bubbles, Drops, and Particles. New York: Dover.
- [7]Davies, C D (1945). “Definitive equations for fluid resistance of spheres”. Proc. Phys. Soc. London A57.4, pp. 259–270. DOI: 10.1088/0959-5309/57/4/301.DOI
- [8]Fuchs, N A (1964). The Mechanics of Aerosols. New York: Dover.
- [9]Goossens, W R A (2019). “Review of the empirical correlations for the drag coefficient of rigid spheres”. Powder Technology 352, pp. 350–359. DOI: 10.1016/j.powtec.2019.04.075.DOI
- [10]Gunn, R and G D Kinzer (1949). “The terminal velocity of fall for water droplets in stagnant air”. Journal of Meteorology 6, pp. 243–248. DOI: 10.1175/1520-0469(1949)006<0243:TVOFF>2.0.CO.doi.org/10.1175/1520-0469(1949)006<0243:ttvoff>2.0.co;2
- [11]Hasadi, Y M F El and J T Padding (2023). “Do logarithmic terms exist in the drag coefficient of a single sphere at high Reynolds numbers?” Chemical Engineering Science 265, p. 118195. DOI: 10.1016/j.ces.2022.118195.
- [12]Klyachko, L S (1934). “Equations of motion for dust particles in dust-collecting devices”. USSR Journal Otoplenie i Ventilyatsiya (Heating and Ventilation) No. 4, pp. 27–29. DOI: 10.48550/arXiv.2610.07315.
- [13]Kramer, O J I, P J de Moel, S K R Raaghav, E T Baars, W H van Vugt, W-P Breugem, J T Padding, and J P van der Hoek (2021). “Can terminal settling velocity and drag of natural particles in water ever be predicted accurately?” Drinking Water Engineering and Science 14.1, 53=71. DOI: 10.5194/dwes-14-53-2021.DOI
- [14]Lamb, H (1932). Hydrodynamics (6th Edition). Cambridge: Cambridge University Press.
- [15]Landau, L D and E M Lifshitz (1959). Fluid Mechanics. London: Pergamon.
- [16]Lapple, C E and C B Shepherd (1940). “Calculation of Particle Trajectories”. Ind. Eng. Chem. 32.5, pp. 605–617.DOI
- [17]Michaelides, E E (2026). “The equation of motion of particles in fluids—An historical perspective”. Powders 5.1, p. 5010005. DOI: 10.3390/powders5010005.DOI
- [18]Pruppacher, H R and J D Klett (1997). Microphysics of Clouds and Precipitation (revised and enlarged edition). Dordrecht: Kluwer Academic Publishers.
- [19]Putnam, A (1961). “Integratable form of droplet drag coefficient”. J. Am. Rochet Soc. 31.10, pp. 1467–1468.
- [20]Ramirez, C A (2017). “Summary of frictional drag coefficient relationships for spheres: Evolving solution strategies applied to an old problem”. Chem. Eng. Sci. 168, pp. 339–343. DOI: 10.1016/j.ces.2017.04.037.DOI
- [21]Schiller, L and A Naumann (1933). “Über die grundlegenden Berechnungen bei der Schw-erkraftaufbereitung”. Zeitschrift des Vereins Deutscher Ingenieure 77.12, pp. 318–320.
- [22]Schlichting, H (1955). Boundary-Layer Theory. New York: McGraw-Hill Book Company.
- [23]Serafini, J S (1954). Impingement of water droplets on wedges and double-wedge airfoils at supersonic speeds. Tech. rep. NASA-TP-1159. NASA Lewis Flight Propulsion Laboratory.
- [24]Wang, P K and H R Pruppacher (1977). “Acceleration to terminal velocity of cloud and raindrops”. J. Appl. Meteor. 16, pp. 275–280. DOI: 10.1175/1520-0450(1977)016<0275:ATTVOC>2.0.CO.doi.org/10.1175/1520-0450(1977)016<0275:attvoc>2.0.co;2
- [25]Zigrang, D J and N D Sylvester (1981). “An explicit equation for particle settling velocities in solid-liquid systems”. AIChE J. 27.6, pp. 1043–1044. DOI: 10 . 1002 / aic . 690270629.DOI
