betaFeedback

WorksPhysics and Astronomy

Resonantly Pumped Tunable Tm,X:CaF2 Lasers: Effect of Buffer Ions (X = Y, La, Gd, and Lu)

Abstract

We report on the eye-safe laser performance of Tm3+-doped calcium fluoride crystals, modified with optically inactive "buffer" cations (Y3+, Lu3+, Gd3+, and La3+), under in-band diode-pumping at 1.68 um. In the free-running regime, the 1.5 at.% Tm, 4 at.% Y:CaF2 laser operates with a high slope efficiency of 47% with respect to absorbed pump power. By employing an MgF2 birefringent plate, the emission wavelength of this laser is continuously tuned over 242 nm (1820 - 2062 nm) highlighting its potential for broadly tunable and ultrafast oscillators. The spectroscopic properties of Tm3+ ions in CaF2 crystals with and without buffer ions are also compared.

Introduction

Tunable lasers have emerged as indispensable tools across a wide range of applications due to their ability to emit light over a continuously adjustable wavelength range. This flexibility allows to precisely select the emission wavelength with a narrow linewidth to match specific absorption features, optimize the system performance or facilitate multiplexed measurements. Tunable lasers are essential for spectroscopy due to their ability to selectively probe molecular transitions [1], for atmospheric monitoring [2], as well as for biomedical imaging [3], optical communications [4] and material processing [5]. In solid-state lasers, the wavelength tuning is usually enabled by a diffraction grating, an etalon or a birefringent filter. A birefringent filter (BRF) is typically made of anisotropic materials (e.g., SiO2_2 or MgF2_2) and has a form of a thin plate [6]. The tuning is achieved by rotating the filter around an axis perpendicular to its surface. Proper operation requires the incoming radiation to be linearly polarized. This can be accomplished by using polarizers or by tilting the filter at the Brewster angle, which also helps reduce the losses in the resonator. The BRF exhibits wavelength-dependent transmission maxima, which can be shifted by its rotation. The tuning range is determined by the spacing between two consecutive maxima, known as the free spectral range (FSR), which is inversely proportional to the filter thickness [7, 8, 9].

Tunable lasers emitting in the vicinity of 2 µm gather attention due to a unique combination of their eye safety, atmospheric transmission and strong molecular absorption features. One of the primary advantages of 2-µm lasers is that such radiation is absorbed more readily in the eye’s cornea reducing the risk of retinal damage and enabling applications in LIDAR and remote sensing. This spectral region also contains the strong absorption lines of several gases, such as H2_2O, CO2_2, CH4_4 and NH3_3, making these lasers effective for trace gas detection and environmental monitoring of atmospheric pollutants, greenhouse gases and industrial emissions [10]. In the medical field, the high tissue absorption at 2 µm facilitates precise tissue ablation with minimal tissue damage [11]. Nowadays, thulium and holmium lasers are mainly used to address the 2-µm range.

The material wise choice of laser gain media for broadly tunable lasers comprises media with strong spectral line broadening, either induced by the electron-lattice (vibronic) interaction in the case of transition-metal ions (vibronic lasers), or by inhomogeneous line broadening in the case of rare-earth ions with their intrinsically narrow 4f – 4f electronic lines. Rare-earth-doped disordered laser gain media allow for continuous wavelength tuning over tens to hundreds of nanometers, covering several electronic lines between Stark sub-levels of the involved multiplets. Rare-earth doped glasses (including glass fibers) naturally appear as the first choice; however, their use is limited by low thermal conductivity and low laser damage thresholds. Single crystals (and polycrystalline transparent ceramics) with a structure and / or compositional disorder present an alternative, even though the local disorder inevitably leads to a drop in their thermal conductivity as compared to ordered crystals. So far, various crystals (ceramics) doped with Tm3+\mathrm{Tm}^{3+} ions and exploiting the structural disorder (such as CaGdAlO4_4 [12, 13] or CNGG-type garnets [14]), or compositional disorder in solid-solution compositions (such as “mixed” sesquioxide ceramics [15, 16]), have enabled broadband tuning of laser emission around 2 μm2\ \mu\mathrm{m}.

Among the disordered laser gain media, cubic calcium fluoride (CaF2_2, called fluorite in the mineral form) crystals stand apart. They readily form solid solutions with rare-earth ions, CaF2_2 – RF3_3, or Ca1−x_{1-x}Rx_xF2+x_{2+x} (accounting for charge neutrality), with the solubility limit up to ∼40\sim40 mol%, retaining their cubic structure. Remarkably, rare-earth ions in CaF2_2 tend to reside in close proximity to each other, forming clusters composed of R3+^{3+}- Fi−_i^- pairs (i – interstitial anion), whose geometry depends on the doping level but also on the nature of the rare-earth cation. Such crystals were called “anti-glasses” [17] as they lack the short-range order while maintaining the long-range one (“islands of disorder in the sea of order”, a situation opposite to that in amorphous glasses). Several distinct cluster types may coexist and within each type (called a “quasi-center”), further diversity of species may be revealed by low temperature spectroscopy. This strongly multi-site behavior results in smooth, structureless and broad absorption and emission bands. Remarkably, the attribution of electronic transitions is often not possible even at cryogenic temperatures when the phonon assisted processes are suppressed.

By combining the broadband emission behavior of rare-earth ions in CaF2_2 with the inherently appealing properties of this fluoride host (namely, high thermal conductivity, negative dn/dT coefficient, low phonon energy, and broadband transparency), these crystals are currently seen as excellent candidates for the replacement of laser glasses in high power / energy facilities operating around 1 μm1\ \mu\mathrm{m} (based on Nd3+^{3+} or Yb3+^{3+} ions). There is also a rising interest in CaF2_2 crystals for 22-μm\mu\mathrm{m} and 33-μm\mu\mathrm{m} lasers [18]. Note that CaF2_2 can also be fabricated in the form of transparent ceramics even though the technology is still far from being mature [19].

Calcium fluoride crystals codoped with several rare-earth ions would contain clusters of complex composition which enhance energy-transfer between them, as in the case of Yb3+^{3+}, Tm3+^{3+} [20] or Tm3+^{3+},Ho3+^{3+} [21] ion pairs. However, if the codopant is optically inactive, it can play the role of a “buffer” effectively suppressing the crosstalk between the neighboring active ions, a property widely exploited to enable laser emission from Nd3+^{3+}-doped CaF2_2 crystals [22, 23]. The “buffer” ions X3+^{3+} could be Y3+^{3+}, La3+^{3+}, Gd3+^{3+}, Lu3+^{3+}, or their combination, and the effect is increased on enhancing the buffer/laser ion coupling ratio. In addition to suppressed energy-transfer processes and reduced luminescence quenching, the variation of the cluster composition changes the multi-ligand environment around the laser-active ions, contributing to an altered crystal-field, and, consequently, Stark splitting of their manifolds, as well as the probabilities of radiative transitions. Finally, the mass difference between the “buffer” and active ions increases the local disorder, which could result in further spectral broadening (although this effect seems to be weaker than the disorder induced by the ion clustering itself). CaF2_2 crystals codoped with laser-active Tm3+^{3+} ions, on one side, and various buffers, have been reported. Veselský et al. reported on a diode-pumped cryogenically cooled Tm,Lu:CaF2_2 reaching slope efficiency of 66% and tuning range of 250 nm from 1785 to 2035 nm [24]. Liu et al. reported on a diode-pumped Tm,Y:CaF2_2 laser delivering 0.45 W at 1.94 μ\mum with a slope efficiency of 21.5% and achieved 190 nm wide tuning range (1850-2040 nm) [25]. Zhang et al. demonstrated power scaling of a Tm,La:CaF2_2 laser up to 4.05 W at 1.92 μ\mum and achieved a similar tuning range, 1840-2032 nm (192 nm wide) [26].

The reduced crosstalk between active ions in complex clusters containing “buffer” ions can negatively affect laser schemes relying on cross-relaxation (CR) to achieve higher pump quantum efficiency (e.g., the 2-μ\mum transition of Tm3+^{3+}) or energy-transfer upconversion (ETU) to avoid the bottleneck effect (e.g., the 2.8-μ\mum transition of Er3+^{3+}). In the case of Tm3+^{3+}, there exists an alternative pumping scheme directly to the upper laser level (the 3H6→3F4^3\mathrm{H}_6 \rightarrow^3\mathrm{F}_4 transition in absorption), referred to as resonant or in-band pumping [27]. Its advantages over conventional pumping around 0.8 μ\mum include lower quantum defect, reduced heat loading, high laser efficiency, independence from the CR process removing the limitations of the Tm3+^{3+} doping level, and operation entirely within the eye-safe spectral region [28]. The Tm3+^{3+},X3+^{3+}-codoped CaF2_2 crystals are appealing for this type of pumping as they benefit from reduced ETU from the upper laser level which usually contributes to increased laser thresholds. In-band pumping of Tm:CaF2_2 crystals has been exploited: Thouroude et al. reported on 1.25 W at 1.88 μ\mum from a Tm:CaF2_2 laser pumped by a 1.61 μ\mum Er-Yb-codoped fiber laser [29].

In the present work, we report a comparative spectroscopic and laser study of five Tm3+^{3+}-doped calcium fluorite crystals, both singly-doped and codoped with various optically inactive “buffer” cations X3+^{3+} = Y3+^{3+}, La3+^{3+}, Gd3+^{3+}, and Lu3+^{3+}. We focus on their wavelength-tuning potential around 2 μ\mum under in-band pumping. As a result, we demonstrate continuous tuning up to 242 nm (1820–2062 nm) with the Tm,Y:CaF2_2 laser, highlighting the potential of these disordered gain media for ultrabroadband coherent light sources.

Crystal growth and spectroscopy

Crystal growth

Single crystals of Tm,X:CaF2_2 were grown by the Bridgman–Stockbarger method using graphite crucibles (∅\varnothing: 8 mm; height: 40 mm). The starting reagents were CaF2_2 (Sigma-Aldrich, purity: 4N) and rare-earth fluorides, RF3_3, R = Tm, Y, La, Gd, and Lu, produced from commercial R2_2O3_3 powders (Alfa Aesar, purity: 4N) using an excess of NH4_4HF2_2 solution at 250 °C, following the reaction R2_2O3_3 + 6 NH4_4HF2_2 → 2 RF3_3 + 6 NH4_4F + 3 H2_2O. The obtained dry cakes were annealed at 650 °C under an Ar atmosphere to remove the residual NH4_4F and moisture. To avoid oxygen contamination, the growth was performed under an inert (Ar + CF4_4) atmosphere. The doping level was 1.5 at.% in Tm3+^{3+} and 4.0 at.% in X3+^{3+} cations (with respect to Ca2+^{2+}). The growth charge was placed into the crucible, which was heated slightly above the melting point (~1418 °C), and the melt was homogenized for about 4 h. The growth was achieved by crystal pulling in a vertical temperature gradient of 30–40 °C/cm at a pulling rate of 1–3 mm/h. After completion of the growth, the crystals were slowly cooled down to room temperature over a period of 48 h. No additional annealing was applied. The crystals were transparent and nearly colorless. No spectroscopic signatures of Tm2+^{2+} ions were detected. The segregation coefficient for Tm3+^{3+} ions was close to unity, and the doping gradient over the entire crystal boule did not exceed 0.2 at.% (as evaluated by absorption measurements).

The laser elements were cut from the central part of the as-grown boules having a thickness of about 5 mm and a diameter of 7 mm. They were polished on both sides with good parallelism and left uncoated, as shown in Figure 1.

Photographs of the as-grown and laser grade polished active media

Figure 1. Photographs of the as-grown and laser grade polished 1.5 at. % Tm3+^{3+}, 4 at. % X3+^{3+}:CaF2_2 (X = no buffer, Y, La, Gd, or Lu) active media.

Optical spectroscopy

Calcium fluoride crystals suffer from relatively low transition cross-sections for the dopant ions (at moderate to high doping levels, where the ion clustering is dominant). This leads to low pump absorption efficiency and low gain in these materials. Physically, this is related to strong inhomogeneous spectral line broadening. Codoping with buffer ions helps to change the cluster composition and (in some cases) enhance the transition cross-sections.

The absorption cross-sections σabs\sigma_{\mathrm{abs}} for the 3H6→3F4^{3}\mathrm{H}_{6} \to{}^{3}\mathrm{F}_{4} transition of Tm3+^{3+} ions in Tm,X:CaF2_2 crystals used for resonant pumping are shown in Figure 2(a). They were calculated using the ion density NTm=3.65×1020N_{\mathrm{Tm}} = 3.65 \times10^{20} at/cm3^{3} (the segregation coefficient for Tm3+^{3+}, KTm∼1K_{\mathrm{Tm}} \sim1).

Spectroscopy of Tm$^{3+}$ ions in CaF$_2$ crystals

Figure 2. Spectroscopy of Tm3+^{3+} ions in CaF2_2 crystals with and without buffers X = Y, La, Gd and Lu: (a) absorption cross-sections, σabs\sigma_{\mathrm{abs}}, for the 3H6→3F4^{3}\mathrm{H}_{6} \rightarrow{}^{3}\mathrm{F}_{4} transition, the spectrum of the InGaAsP/InP pump diode is shown for comparison; (b) stimulated-emission (SE) cross-sections, σSE\sigma_{\mathrm{SE}}, for the 3F4→3H6^{3}\mathrm{F}_{4} \rightarrow{}^{3}\mathrm{H}_{6} transition; (c) gain spectral profiles, σg=βσSE−(1−β)σabs\sigma_{\mathrm{g}} = \beta\sigma_{\mathrm{SE}} - (1 - \beta)\sigma_{\mathrm{abs}}, for an inversion ratio β=0.4\beta= 0.4; (d) fluorescence decay curves, λexc=1.62\lambda_{\mathrm{exc}}=1.62 μ\mum, λlum=1.86\lambda_{\mathrm{lum}}=1.86 μ\mum, τlum\tau_{\mathrm{lum}} – luminescence lifetime.

Depending on the nature of the buffer ion, the peak σabs\sigma_{\mathrm{abs}} at 1.61 μ\mum varies significantly, ranging from 2.18×10−212.18 \times10^{-21} cm2^{2} (for Tm,La:CaF2_2) to 6.28×10−216.28 \times10^{-21} cm2^{2} (for Tm,Y:CaF2_2). For the latter crystal, the absorption bandwidth (full width at half maximum) is 16 nm. These absorption cross-sections exceed those for the 3H6→3H4^{3}\mathrm{H}_{6} \to{}^{3}\mathrm{H}_{4} transition at 0.8 μ\mum (in the respective compositions), highlighting the potential of resonant pumping for boosting the pump absorption efficiency in Tm-lasers. The σabs\sigma_{\mathrm{abs}} values at the pump wavelength employed in the present work (1.68 μ\mum) are listed in Table 1.

Crystalσabs\sigma_{\mathrm{abs}}, 10−21 cm210^{-21}\,\mathrm{cm}^2 at 1.68 μm\mu\mathrm{m}σSE\sigma_{\mathrm{SE}}, 10−21 cm210^{-21}\,\mathrm{cm}^2 at 1.9 μm\mu\mathrm{m}τlum\tau_{\mathrm{lum}}, msΔλg\Delta\lambda_g, nm, for β=0.4\beta= 0.4
Tm:CaF2_21.431.0417.2108
Tm,Y:CaF2_21.291.1012.1111
Tm,La:CaF2_21.691.0615.7120
Tm,Gd:CaF2_21.311.1817.3123
Tm,Lu:CaF2_21.671.018.5109

Table 1. Key spectroscopic parameters of Tm3+^{3+} ions in the Tm,X:CaF2_2 crystals. σabs\sigma_{\mathrm{abs}} – absorption cross-section for in-band pumping, σSE\sigma_{\mathrm{SE}} – stimulated-emission cross-section, τlum\tau_{\mathrm{lum}} – luminescence lifetime, Δλg\Delta\lambda_g – gain bandwidth (FWHM).

The stimulated-emission (SE) cross-sections σSE\sigma_{\mathrm{SE}} for the 3F4→3H6^{3}\mathrm{F}_{4} \to{}^{3}\mathrm{H}_{6} laser transition were calculated from the measured fluorescence spectra I(λ)I(\lambda) (corrected for the structured water vapor absorption) using the Füchtbauer-Ladenburg equation [30]:

σSE(λ)=λ58πc⟨n⟩2τradI(λ)∫I(λ)λ dλ(1)\sigma_{\mathrm{SE}}(\lambda) = \frac{\lambda^{5}}{8\pi c\langle n\rangle^{2}\tau_{\mathrm{rad}}}\frac{I(\lambda)}{\int I(\lambda)\lambda\,\mathrm{d}\lambda} \tag*{(1)}

where λ\lambda is the emission wavelength, ⟨n⟩≈1.42\langle n\rangle\approx1.42 is the mean refractive index of the CaF2_2 crystal [31], cc is the speed of light, and τrad=21.3\tau_{\mathrm{rad}} = 21.3 ms is the radiative lifetime of the 3F4^{3}\mathrm{F}_{4} state [32]. A very small effect of the crystal composition on this value was observed (within the error of the analysis). The SE cross-sections are given in Figure 2(b). Their spectral dependence is less sensitive to the nature of the buffer ion. Around 1.9 μ\mum, σSE\sigma_{\mathrm{SE}} lies in the range of 1.0–1.2 ×10−21\times10^{-21} cm2^{2} for all the studied crystals, see Table 1.

According to the quasi-3-level operation scheme of Tm lasers with reabsorption, the gain cross-sections, σg=βσSE−(1−β)σabs\sigma_{\mathrm{g}} = \beta\sigma_{\mathrm{SE}} - (1 - \beta)\sigma_{\mathrm{abs}}, were calculated. They are compared for the studied Tm,X:CaF2_2 crystals for a given inversion ratio β=0.4\beta= 0.4 (where β=N2/NTm\beta= N_{2}/N_{\mathrm{Tm}}, N2N_{2} is the population of the upper laser level, 3F4^{3}\mathrm{F}_{4}). The gain profiles are broad and almost structureless, and they extend beyond 2 μ\mum, see Figure 2(c). The gain bandwidth (FWHM) was calculated, cf. Table 1, ranging from 108 nm (for Tm:CaF2_2) to 123 nm (Tm,Gd:CaF2_2).

The luminescence decay curves from the 3F4^{3}\mathrm{F}_{4} manifold measured under resonant excitation are plotted in Figure 2(d). Finely powdered crystalline samples were used to reduce the effect of radiation trapping (reabsorption). The decay is close to single-exponential, suggesting a single type of Tm (or Tm–X) clusters (“quasi-centers”, as proposed by Kaminskii [33]). The nature of the buffer has a significant influence on the upper laser level lifetime, which ranges from 8.50 ms (for Tm,Lu:CaF2_2) to 17.33 ms (for Tm,Gd:CaF2_2), see Table 1.

From the point of view of spectroscopic properties, generally speaking, one should select a crystal combining: i) high absorption cross-sections (for efficient pumping), ii) the broadest gain profiles extending far beyond 2 μ\mum (for broadband wavelength tuning and reduced impact of water vapor absorption), and iii) the longest luminescence lifetime (for low laser thresholds). The Tm,Gd:CaF2_2 crystal appears as the most promising candidate. At the same time, these criteria can be conflicting, e.g., the strongest spectral broadening will inevitably lead to lower transition cross-sections.

Resonantly pumped laser operation

Laser set-up

The layout of the laser setup is depicted in Figure 3. For laser experiments, the crystals were polished to laser grade quality and left uncoated. They were mounted in a massive copper holder cooled by circulating water (15 °C) using indium foil for better thermal contact. A near hemispherical resonator was used, formed by a plane dichroic pump mirror coated for high reflectance (HR) at 1.9–2.15 μ\mum and high transmission (HT, T>92%T > 92\%) at 1.68 μ\mum, and a set of curved output couplers (OC) with reflectivity at the laser wavelength ROCR_{\mathrm{OC}} ranging between 92.4% to 99.8%, and a radius of curvature (rOCr_{\mathrm{OC}}) of -100 mm or -150 mm. The laser crystal was positioned 3 mm away from the pump mirror. The pump source was a fiber-coupled (fiber core diameter: 400 μ\mum, N.A. = 0.22) InGaAsP/InP laser diode (QPC Lasers, model BrightLase Ultra-100 6217-0003) emitting up to 30 W of unpolarized radiation at a central wavelength of 1.68 μ\mum. Although the absorption cross-section of Tm3+^{3+} in our crystals peaks near 1.61 μ\mum (Figure 2a), no pump source was available at this wavelength. The chosen 1.68 μ\mum emission still lies within the broad 3H6→3F4^3\mathrm{H}_6 \rightarrow^3\mathrm{F}_4 absorption band of Tm3+^{3+} ions, ensuring efficient in-band pumping. With increasing driving current, the emission wavelength exhibited a red-shift of about 0.2 nm/A, and the measured laser linewidth (FWHM) was approximately 16 nm. The output from the diode was collimated and focused into the crystal using a pair of achromatic doublets with a focal length of f=75f = 75 mm each, resulting in a 1:1 reimaging ratio and a measured pump spot radius of 190 ±\pm 10 μ\mum in the focus. The diode emission was characterized by the measured half divergence angle of 163 ±\pm 5 mrad, and a beam quality factor M2M^2 of 58 ±\pm 4 (measured behind the focusing optics). The pump radiation was electronically modulated, resulting in 10 ms pulses at a repetition rate of 10 Hz (pulse pumping). The pumping was single pass. The measured small-signal pump absorption efficiency was in the range of 21% to 30%, depending on the buffer ion, in agreement with the absorption spectra, and on increasing the pump level, it further dropped by 8% due to a combined effect of the ground-state bleaching and red-shift of the diode wavelength.

Figure 3. Layout of the wavelength tunable resonantly diode-pumped Thulium laser.

The mean output power of the laser radiation was measured using a Thorlabs PM100USB power meter equipped with an S401C sensor. The spectra of both the pump and laser radiation were recorded using a StellarNet RED-Wave spectrometer. The beam profile was captured with a Spiricon Pyrocam IV camera (pixel size: 80 ×\times 80 μm2\mu\mathrm{m}^2).

The tuning of the laser wavelength was enabled by a birefringent filter (BRF) made of MgF2\mathrm{MgF_2}, which is a positive uniaxial material. The BRF had a diameter of 20 mm and a thickness of 1 mm, with its optical axis lying in the plane of the filter. It was placed in the resonator at the Brewster angle, close to the laser crystal.

At the wavelength around 2 μ\mum, the free spectral range (FSR) of the filter was 288–440 nm depending on the rotation angle. The filter was mounted in a motorized rotation holder (SmarAct, model SR-5714). During the wavelength tuning, the average output power and the spectrum of the laser radiation were simultaneously measured for different filter rotation angles with a step of 1.7 mrad.

Free-running laser operation

First, free-running laser operation was exploited (without the BRF in the cavity). The input–output characteristics for different output coupling rates for the best-performing crystal Tm,Y:CaF2\mathrm{Tm,Y:CaF_2} are shown in Figure 4(a).

Figure 4. Resonantly diode-pumped Tm,Y:CaF2_2 laser operating in the free-running regime: (a) power transfer curves, duty cycle: 1:10, η\eta – slope efficiency, PthP_{\mathrm{th}} – laser threshold (vs. absorbed pump pulse energy); (b) typical spectra of laser emission (unpolarized output).

An output pulse energy of 9.4 mJ was achieved at an absorbed pump pulse energy of 29.6 mJ, corresponding to a slope efficiency η\eta of 47% and a laser threshold PthP_{\mathrm{th}} of 8.5 mJ (for ROC=93.9%R_{\mathrm{OC}} = 93.9\%). On decreasing the output coupler reflectivity from 99.8% to 92.4%, the laser threshold increased from 1.9 mJ to 7.6 mJ.

The typical spectra of laser emission measured well above the laser threshold are presented in Figure 4(b), revealing a blue-shift of the laser wavelength for higher output coupling rates, from 1919 nm (ROC=99.8%R_{\mathrm{OC}} = 99.8\%) to 1877 nm (ROC=92.4%R_{\mathrm{OC}} = 92.4\%). This behavior is typical for quasi-3-level Tm lasers with reabsorption and aligns well with the gain profiles.

The measured duration of laser pulses increased with the pump level in the range of 0.2 to 11 ms.

Figure 5 compares the output characteristics (power transfer curves and typical laser spectra) of all five tested laser crystals for a given output coupler reflectivity of 98.0%. Note that the different pump absorption efficiencies determine the range of the absorbed pump pulse energies. The maximum incident pump pulse energy was the same: 221 mJ. There is a significant variation in laser efficiency with the crystal composition, which is mostly associated with the crystal quality. The best performance was achieved for the Tm,Y:CaF2\mathrm{Tm,Y:CaF_2} crystal.

Figure 5. Effect of the rare-earth buffer (X = Y, La, Gd and Lu) incorporation on the output performance of resonantly diode-pumped Tm,X:CaF₂ lasers: (a) input-output dependences, η\eta – slope efficiency, PthP_{\mathrm{th}} – laser threshold (vs. absorbed pump pulse energy); (b) laser emission spectra. Output coupler reflectivity: ROCR_{\mathrm{OC}} = 98%, free-running regime.

The typical beam profiles in the far-field for the Tm,X:CaF2\mathrm{Tm,X:CaF_2} lasers are compared in Figure 6. The lasers operated on the fundamental transverse mode. Based on these profiles, the beam quality factor was estimated as M2<1.6M^2 < 1.6 for all tested samples.

Figure 6. Far-field beam profiles of the in-band diode-pumped Tm,X:CaF₂ lasers (taken at ∼\sim40 cm from the OC).

Wavelength tuning

The wavelength tuning experiment was performed for two output couplers with reflectivities ROCR_{\mathrm{OC}} of 99.8% and 98.0%, under identical pumping conditions (incident pump pulse energy of 221 mJ, pump pulse length of 10 ms, repetition rate of 10 Hz). The tuning curves are given in Figure 7(a,Figure 7b). They are relatively flat and broad, with the wavelength being continuously tuned within the corresponding ranges. The broadest tuning range, accompanied by the highest output energy, was achieved for the Tm,Y:CaF₂ crystal in both cases. For the higher-reflectivity mirror, the tuning range was 1820–2062 nm (242 nm at the zero-power level), and for the lower-reflectivity mirror, it was narrower, measuring 1826–2008 nm (182 nm). Figure 7(c) summarizes the tuning ranges for all the studied crystals.

Figure 7. Results of the laser tuning experiments for resonantly diode-pumped Tm,X:CaF2_2 lasers (X = no buffer, Y, La, Gd and Lu): (a,b) Output coupler reflectivity: (a) ROC=99.8%R_{\mathrm{OC}} = 99.8\%, (b) ROC=98%R_{\mathrm{OC}} = 98\%; (c) an overview of the obtained tuning ranges at the zero power; grey lines – water vapor absorption (HITRAN database, https://hitran.org/).

Discussion

Let us discuss the criteria for the choice of “buffer” ions aiming the material engineering of highly performant Tm,X:CaF2_2 laser gain media for broadly tunable 2 µm lasers. While Tm,Gd:CaF2_2 fulfills most of the spectroscopic criteria, the realized laser output is governed by the passive losses. In our set, Tm,Y:CaF2_2 exhibited a lower threshold and higher slope efficiency (Figure 5a), which we attribute to its lower passive loss (higher optical quality). The crystals used here were primarily fabricated for spectroscopic studies, i.e., not grown in laser-grade quality; this could have penalized Tm,Gd:CaF2_2 more strongly. Nevertheless, Tm,Gd:CaF2_2 delivered the second-best laser performance and tuning range in our set, suggesting that with improved growth its superior spectroscopic properties could translate into higher slope efficiency and broader tuning range. Furthermore, the difference between the ionic radii of the Tm3+^{3+} (1.13 Å), X3+^{3+} (from 1.11 Å for Lu3+^{3+} to 1.32 Å for La3+^{3+}) and Ca2+^{2+} (1.26 Å, all the values are given for VIII-fold fluorine coordination [34]) may be the main factor explaining the variations in the optical quality of grown crystals.

Previous structural studies on rare-earth ion clusters in CaF2_2 – RF3_3 fluorite-type solid-solutions [35, 36, 37, 38] revealed their two main geometries of different sizes: tetrahedral (small) R4_4F26_{26} ones and octahedrocubic (large) Ca8_8R6_6F69_{69} or Ca9_9R5_5F69_{69} ones, which substitute for the Ca4_4F2315−_{23}^{15-} and Ca14_{14}F6436−_{64}^{36-} building blocks of the host structure, respectively (the so-called block isomorphism). Their formation is evidenced by the presence of Fn−_n^-, respectively, 32ff sites and 48i48i sites. The local charge compensation is maintained by mobile carriers Fmob−\mathrm{F}^{-}_{\mathrm{mob}} at the periphery of these defect regions. Depending on the nature of the rare-earth ion, these solid-solutions can be divided into three groups: i) those with only tetrahedral clusters (R=La\mathrm{R} = \mathrm{La} to Tb\mathrm{Tb}), ii) those with only octahedrocubic ones (R=Er\mathrm{R} = \mathrm{Er} to Lu\mathrm{Lu}), and iii) those in which both geometries can coexist (R=Y\mathrm{R} = \mathrm{Y}, Dy\mathrm{Dy}, Ho\mathrm{Ho}).

Physically, strong (or weak) effect of the introduction of “buffer” ions into the Tm3+\mathrm{Tm}^{3+}-doped CaF2\mathrm{CaF}_{2} crystal can be explained as follows: for crystals singly doped with Tm3+\mathrm{Tm}^{3+}, only octahedrocubic clusters exist (with an octahedral arrangement of R3+\mathrm{R}^{3+} and Ca2+\mathrm{Ca}^{2+} in the first coordination sphere and cubic arrangement of Ca2+\mathrm{Ca}^{2+} in the second coordination sphere). This well agrees with the nearly single-exponential decay of Tm3+\mathrm{Tm}^{3+} ions in heavily doped (a few at.%) CaF2\mathrm{CaF}_{2} crystals suggesting the existence of a single “quasi-center”. By codoping the crystal with “buffer” cations belonging to the same group (e.g., Lu3+\mathrm{Lu}^{3+}), one still expects the Ca8R6F69\mathrm{Ca}_{8}\mathrm{R}_{6}\mathrm{F}_{69} or Ca9R5F69\mathrm{Ca}_{9}\mathrm{R}_{5}\mathrm{F}_{69} clusters. Indeed, the effect of Lu3+\mathrm{Lu}^{3+} on the variation of the absorption and emission profiles is weak. In contrast, by codoping with cations that favor the formation of only tetrahedral clusters (i.e., La3+\mathrm{La}^{3+} or Gd3+\mathrm{Gd}^{3+}), a much stronger disorder is introduced which is indeed reflected in the spectral profiles. The case of Tm3+,Y3+\mathrm{Tm}^{3+},\mathrm{Y}^{3+}:CaF2\mathrm{CaF}_{2} is exceptional as two types of clusters are expected to coexist (note that for this crystal, the strongest deviation from Tm:CaF2_2 as can be seen in Figure 2(a,Figure 2b)).

Further optimization of the material composition should focus on finding the best Tm/X codoping ratio for a given Tm concentration. Note that for in-band pumping which does not rely on cross-relaxation, efficient laser operation even at low Tm doping levels is possible as long as the combination of the doping concentration and the sample length (e.g., in the “rod” geometry) provides sufficient pump absorption efficiency. The rare-earth doping into CaF2\mathrm{CaF}_{2} (accounting for both laser-active and “buffer” ions) rapidly decreases the thermal conductivity of the crystal leading to a higher probability of thermal fracture which is already a serious issue for an overall doping level of 5 at.% [39, 40]. It seems that this decline in thermal properties is nearly the same for all the rare-earth ions, as demonstrated by Pavel Popov in his systematic studies [41, 42]. Therefore, it is desirable to keep the Tm3+\mathrm{Tm}^{3+} doping level low (about 0.3 to 1 at.%) and optimize the Tm/X codoping ratio (1:2 to 1:5) to induce a noticeable variation in the crystal-field within rare-earth clusters which are readily formed at an overall doping level exceeding 0.5 at.% (i.e., the targeted range for the “buffer” ions is 0.6 to 5 at.%).

Conclusion

To conclude, we report on the first comparative study of five Tm3+\mathrm{Tm}^{3+}-doped calcium fluoride crystals singly doped and codoped with optically inactive “buffer” cations (Y3+\mathrm{Y}^{3+}, La3+\mathrm{La}^{3+}, Gd3+\mathrm{Gd}^{3+} and Lu3+\mathrm{Lu}^{3+}), regarding their widely tunable laser operation in the eye-safe spectral range of 2 μ\mum. As the main parameter for assessing crystal performance, we chose the wavelength tuning range, which in fact combines the contributions from spectroscopic behavior (e.g., via the accessible gain bandwidth and the upper-laser level lifetime) and the optical quality of the crystals (via the total intracavity losses). We also employed the in-band pumping scheme at 1.68 μ\mum which does not rely on the cross-relaxation mechanism and consequently allows one to operate at lower Tm3+\mathrm{Tm}^{3+} doping levels (1.5 at.%, in the present work) accessing better thermal properties of the crystals.

We identify the Tm,Y:CaF2_2 crystal as the most promising candidate for widely tunable continuous-wave and potentially femtosecond mode-locked lasers, as in the free-running regime, it enables a remarkable tuning range of 242 nm (1820–2062 nm), extending far beyond 2 μ\mum even despite the inherently weak crystal-field strengths in fluoride matrices. This crystal also demonstrates a laser slope efficiency up to 47%, which could be further improved by optimizing the pump-laser mode overlap in the resonator, as well as reducing the Tm3+\mathrm{Tm}^{3+} doping level to suppress ETU from the upper laser manifold. We suggest an explanation for this remarkable performance, by analyzing the variety of rare-earth cluster types.

We believe that true continuous-wave laser operation in the multi-Watt regime is possible when applying proper cooling of laser crystals (e.g., in the rod geometry) and reducing the overall rare-earth (Tm3++X3+\mathrm{Tm}^{3+} + \mathrm{X}^{3+}) doping to a few at.%. Another way to extend the tuning range far beyond 2 µm would be to explore in-band pumping of triply doped (Tm3+\mathrm{Tm}^{3+}, Ho3+\mathrm{Ho}^{3+}, X3+\mathrm{X}^{3+}) crystals.

Acknowledgement. Preliminary results were presented at CLEO/Europe-EQEC 2025 [43].

Funding. This work has been funded by a grant from the Programme Johannes Amos Comenius under the Ministry of Education, Youth and Sports of the Czech Republic from the project LASCIMAT, project No. CZ.02.01.01/00/23_020/0008525. As set out in the Legal Act, beneficiaries must ensure that the open access to the published version or the final peer-reviewed manuscript accepted for publication is provided immediately after the date of publication via a trusted repository under the latest available version of the Creative Commons Attribution International Public Licence (CC BY) or a licence with equivalent rights. This work has been also funded by French Agence Nationale de la Recherche (ANR-22-CE08-0031, FLAMIR) and Région Normandie, France (Contrat de plan État-Région (CPER)).

Disclosures. The authors declare no conflicts of interest.

Data Availability Statement. Data underlying the results presented in this paper are available in dataset "Tm,X:CaF2_2 lasers", Ref. [44].

References

  1. [1]Z. Du, S. Zhang, J. Li, et al., “Mid-Infrared Tunable Laser-Based Broadband Fingerprint Absorption Spectroscopy for Trace Gas Sensing: A Review,” Appl. Sci. 9, 338 (2019).DOI
  2. [2]E. D. Hinkley, K. W. Nill, and F. A. Blum, “Infrared spectroscopy with tunable lasers,” in Laser Spectroscopy of Atoms and Molecules, vol. 2 H. Walther, ed. (Springer Berlin Heidelberg, Berlin, Heidelberg, 1976), pp. 125–196.DOI
  3. [3]S. Yun, C. Boudoux, M. Pierce, et al., “Extended-Cavity Semiconductor Wavelength-Swept Laser for Biomedical Imaging,” IEEE Photonics Technol. Lett. 16, 293–295 (2004).pubmed.ncbi.nlm.nih.gov/20640193
  4. [4]H. Al-Taiy, N. Wenzel, S. Preusler, et al., “Ultra-narrow line-width, stable and widely tuneable laser source for coherent optical communication systems,” in 2014 The European Conference on Optical Communication (ECOC), (IEEE, Cannes, France, 2014), pp. 1–3.
  5. [5]F. J. Duarte, Tunable Laser Applications (CRC/Taylor & Francis, Boca Raton, FL, 2009), 2nd ed.
  6. [6]J. Wei, J. Su, H. Lu, and K. Peng, “A Review of Progress about Birefringent Filter Design and Application in Ti:sapphire Laser,” Photonics 10, 1217 (2023).DOI
  7. [7]O. Svelto, Principles of Lasers (Springer US, Boston, MA, 2010).
  8. [8]S. Kobtsev and N. Sventitskaya, “Application of birefringent filters in continuous-wave tunable lasers: A review,” Opt. Spectrosc. pp. 114–123 (1992).
  9. [9]S. Zhu, “Birefringent filter with tilted optic axis for tuning dye lasers: Theory and design,” Appl. Opt. 29, 410 (1990).DOI
  10. [10]T. S. McComb, R. A. Sims, C. C. Willis, et al., “Atmospheric Transmission Testing Using a Portable, Tunable, High Power Thulium Fiber Laser System,” in Conference on Lasers and Electro-Optics 2010, (OSA, San Jose, California, 2010), p. JThI5.DOI
  11. [11]T. Bilici, “Modulated and continuous-wave operations of low-power thulium (Tm:YAP) laser in tissue welding,” J. Biomed. Opt. 15, 038001 (2010).DOI
  12. [12]Y. Wang, G. Xie, X. Xu, et al., “SESAM mode-locked Tm:CALGO laser at 2 μm,” Opt. Mater. Express 6, 131 (2016).
  13. [13]Z. Pan, P. Loiko, J. M. Serres, et al., ““Mixed” Tm:Ca(Gd,Lu)AlO₄ — a novel crystal for tunable and mode-locked 2 μm lasers,” Opt. Express 27, 9987 (2019).DOI
  14. [14]Z. Pan, J. M. Serres, E. Felicetti, et al., “Comparative study of the spectroscopic and laser properties of Tm³⁺, Na⁺(Li⁺)-codoped Ca₃Nb₁₅Ga₃₅O₁₂-type disordered garnet crystals for mode-locked lasers,” Opt. Mater. Express 8, 2287 (2018).DOI
  15. [15]Y. Wang, W. Jing, P. Loiko, et al., “Sub-10 optical-cycle passively mode-locked Tm:(Lu₂/₃Sc₁/₃)₂O₃ ceramic laser at 2 μm,” Opt. Express 26, 10299 (2018).DOI
  16. [16]Y. Zhao, L. Wang, W. Chen, et al., “SESAM mode-locked Tm:LuY₂O₃ ceramic laser generating 54-fs pulses at 2048 nm,” Appl. Opt. 59, 10493 (2020).
  17. [17]S. V. Kuznetsov, V. V. Osiko, E. A. Tkatchenko, and P. P. Fedorov, “Inorganic nanofluorides and related nanocomposites,” Russ. Chem. Rev. 75, 1065–1082 (2006).
  18. [18]S. Normani, P. Loiko, L. Basyrova, et al., “Mid-infrared emission properties of erbium-doped fluorite-type crystals,” Opt. Mater. Express 13, 1836 (2023).DOI
  19. [19]J. Šulc, M. Němec, H. Jelínková, et al., “Diode pumped tunable lasers based on Tm:CaF₂ and Tm:Ho:CaF₂ ceramics,” in SPIE LASE, W. A. Clarkson and R. K. Shori, eds. (San Francisco, California, United States, 2014), p. 895925.DOI
  20. [20]R. Soulard, J. Doualan, A. Braud, et al., “1.87 μm laser operation by 980 nm pumping in Yb,Tm:CaF₂,” Opt. Mater. 72, 578–582 (2017).DOI
  21. [21]K. Eremeev, P. Loiko, A. Benayad, et al., “Efficient continuous-wave Tm,Ho:CaF₂ laser at 2.1μm,” Opt. Lett. 48, 1730 (2023).DOI
  22. [22]S. Normani, A. Braud, R. Soulard, et al., “Site selective analysis of Nd³⁺–Lu³⁺doped CaF₂ laser crystals,” CrystEngComm 18, 9016–9025 (2016).
  23. [23]C. Meroni, A. Braud, J. Doualan, et al., “Spectroscopy and laser gain measurements of CaF₂: Nd, X³⁺, Z³⁺ (X, Z = Gd, La, Ce, Y, Lu, Sc) crystals for broadband lasers applications,” J. Lumin. 252, 119336 (2022).DOI
  24. [24]K. Veselský, J. Šulc, H. Jelínková, et al., “Spectroscopy and lasing of cryogenically cooled Tm³⁺,Lu³⁺:CaF₂ crystal,” J. Lumin. 255, 119563 (2023).DOI
  25. [25]X. Liu, K. Yang, S. Zhao, et al., “Growth and lasing performance of a Tm,Y:CaF₂ crystal,” Opt. Lett. 42, 2567 (2017).DOI
  26. [26]Z. Zhang, X. Guo, J. Wang, et al., “High-efficiency 2 μm continuous-wave laser in laser diode-pumped Tm³⁺, La³⁺ : CaF₂ single crystal,” Opt. Lett. 43, 4300 (2018).
  27. [27]P. Loiko, R. Thouroude, R. Soulard, et al., “In-band pumping of Tm:LiYF₄ channel waveguide: A power scaling strategy for ∼2 μm waveguide lasers,” Opt. Lett. 44, 3010 (2019).
  28. [28]J. Kratochvíl, J. Šulc, M. Němec, and H. Jelínková, “Efficient resonant diode pumping of 2 μm thulium lasers at 1.7 μm,” in Solid State Lasers XXXIII: Technology and Devices, W. A. Clarkson and R. K. Shori, eds. (SPIE, San Francisco, United States, 2024), p. 2.
  29. [29]R. Thouroude, A. Tyazhev, A. Hideur, et al., “Widely tunable in-band-pumped Tm:CaF₂ laser,” Opt. Lett. 45, 4511 (2020).DOI
  30. [30]B. Aull and H. Jenssen, “Vibronic interactions in Nd:YAG resulting in nonreciprocity of absorption and stimulated emission cross sections,” IEEE J. Quantum Electron. 18, 925–930 (1982).
  31. [31]I. H. Malitson, “A Redetermination of Some Optical Properties of Calcium Fluoride,” Appl. Opt. 2, 1103 (1963).
  32. [32]P. Loiko, G. Brasse, L. Basyrova, et al., “Spectroscopy of Tm³⁺-doped CaF₂ waveguiding thin films grown by Liquid Phase Epitaxy,” J. Lumin. 238, 118109 (2021).
  33. [33]A. A. Kaminskii, Crystalline Lasers: Physical Processes and Operating Schemes (CRC Press, 2020), 1st ed.
  34. [34]A. A. Kaminskii, Laser Crystals: Their Physics and Properties, no. v.14 in Springer Series in Optical Sciences Ser (Springer Berlin / Heidelberg, Berlin, Heidelberg, 1990), 2nd ed.DOI
  35. [35]E. A. Sulyanova and B. P. Sobolev, “The universal defect cluster architecture of fluorite-type nanostructured crystals,” CrystEngComm 24, 3762–3769 (2022).
  36. [36]N. I. Sorokin, A. M. Golubev, and B. P. Sobolev, “Structural mechanisms of superionic conductivity in M₁-xRₓF₂+x single crystals,” Crystallogr. Reports 59, 238–247 (2014).
  37. [37]A. A. Ivanov-Shits, “Specific features of ionic transport in nonstoichiometric fluorite-type Ca₁-xRₓF₂+x (R=La-Lu, Y, Sc) phases,” Solid State Ionics 37, 125–137 (1990).
  38. [38]B. P. Sobolev, A. M. Golubev, and P. Herrero, “Fluorite M₁-xRₓF₂+x phases (M = Ca, Sr, Ba; R = rare earth elements) as nanostructured materials,” Crystallogr. Reports 48, 141–161 (2003).
  39. [39]K. Liu, D. Jiang, G. Bian, and L. Su, “Calculating and analyzing the relationship between thermal conductivity and microstructure in rare-earth doped fluoride crystals,” CrystEngComm 27, 2623–2634 (2025).
  40. [40]F. Druon, S. Ricaud, D. N. Papadopoulos, et al., “On Yb:CaF₂ and Yb:SrF₂: Review of spectroscopic and thermal properties and their impact on femtosecond and high power laser performance [Invited],” Opt. Mater. Express 1, 489 (2011).
  41. [41]P. A. Popov, P. P. Fedorov, S. V. Kuznetsov, et al., “Thermal conductivity of single crystals of Ca₁−xYbₓF₂+x solid solutions,” Doklady Phys. 53, 198–200 (2008).
  42. [42]P. A. Popov, P. P. Fedorov, and V. A. Konyushkin, “Thermal conductivity of single crystals of Ba₁−xRₓF₂+x (R = La, Ce, Nd, or Gd) solid solutions,” Crystallogr. Reports 62, 283–287 (2017).
  43. [43]D. Popelová, K. Veselský, J. Šulc, et al., “Resonantly Pumped Tm-Doped and Y/Lu/Gd/La Buffered CaF₂ Lasers Tunable in Wide Wavelength Range of 1820–2062 nm,” in 2025 Conference on Lasers and Electro-Optics Europe &amp; European Quantum Electronics Conference (CLEO/Europe-EQEC), (IEEE, Munich, Germany, 2025), pp. 1–1.
  44. [44]D. Popelová, “Tm,X:CaF₂ lasers,” Mendeley Data (2025). Available at: https://doi.org/10.17632/dyddsg8rzs.1.

Paper details

vlnc:W_ck4v6fwr
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents