WorksPhysics and Astronomy
Compressible unsteady aerodynamics of finite-chord porous aerofoils
Abstract
A unified linear theory is developed for the unsteady loading of finite-chord aerofoils, rigid or porous, in compressible subsonic flow. The formulation combines Possio's integral operator with a convective permeable boundary condition, allowing chordwise-varying admittance while retaining the wake and unsteady Kutta condition. The loading exponents at aerofoil edges and admittance discontinuities keep their incompressible form in terms of the local permeability parameter, so weighted-Jacobi collocation carries over. The solution is verified against published incompressible results and an independent compressible formulation. Gust and heave responses and their indicial counterparts reveal that permeability controls the sensitivity of unsteady loading to compressibility. As permeability increases, the material impedance rather than the surrounding flow sets the pressure jump, but only gradually: at Mach number 0.7 the gust load on a weakly permeable surface changes by a third to a half, and closed-form steady and high-frequency limits for resistive surfaces show that it vanishes only when the permeability parameter greatly exceeds the Mach number. The porous-to-impermeable load ratio, by which a treatment is judged, cannot be obtained by combining incompressible porous and compressible rigid theories, which misjudge it by up to a factor of two. Incompressible theory overestimates this ratio for an acoustically compact chord and underestimates it for a non-compact one, by factors of 1.4 to 4.3 at Mach numbers 0.5 to 0.7 and reduced frequencies 5 to 20, overstating the load reduction. Since compactness depends on Mach number times reduced frequency, the error persists at low speed, exceeding 10 per cent at Mach number 0.05 for reduced frequencies above 10.
Introduction
An aerofoil in a non-uniform or unsteady stream carries an unsteady load, and the classical theory of that load is the foundation of aeroelasticity, of rotor and propeller load prediction, and of every engineering model of turbulence-interaction noise [6, 16, 31]. It comprises Theodorsen [36] for a section oscillating in a uniform stream, Sears [35] and von Kármán and Sears [38] for a section meeting a convected gust, Wagner [39] and Küssner [26] for the corresponding indicial responses, and Possio [34] for the compressible kernel. All of it assumes an impermeable surface.
Permeable surfaces are of interest because the loading they carry at an edge is weaker. Ffowcs Williams and Hall [10] showed that the efficiency with which a half-plane scatters near-field pressure into sound is controlled by the inverse-square-root singularity of the loading at a rigid edge; softening that singularity is the mechanism behind every porous edge treatment, and porous leading and trailing edges have been measured to reduce broadband noise appreciably [13, 9, 7]. Porosity is one of a family of passive edge treatments, alongside serrations, brushes, and compliant and graded surfaces, but the family does not act through a single mechanism. A large part of the benefit of serrations comes from destructive interference between sources distributed along an oblique edge, so it is a property of the radiation and is retained in rotor predictions only when the acoustic calculation keeps the edge geometry and the spanwise phase of the loading [25, 8, 30, 29]. Porous, poroelastic and graded edges act instead on the edge singularity itself [22, 2], so their benefit is carried by the unsteady load, and the reduction predicted in application depends on how the treatment is represented in the loading model rather than in the acoustic analogy that follows it [27]. The same singularity that sets the scattering, moreover, is what generates leading-edge suction, so for this class of treatment the aerodynamic price is fixed by the same quantity as the benefit. Both statements are statements about loading, and both therefore belong to unsteady aerodynamics rather than to acoustics. That is the subject of this paper: what a permeable surface does to the unsteady load on a finite chord in compressible flow, before any acoustic analogy is applied.
Analytical treatments of permeable surfaces divide by geometry. Jaworski and Peake [22] solved the semi-infinite problem by Wiener–Hopf, with the static porosity condition of Howe [20], in which the flow through the surface is proportional to the pressure jump across it. They showed that, in certain parametric limits, the far-field acoustic power of a porous edge scales with the sixth power of the flow speed rather than the fifth power found for a rigid edge, a result that motivated much of what followed. The finite-chord problem is different in kind: the chord introduces a second edge, a shed wake and the Kutta condition, none of which the half-plane carries. Hajian and Jaworski [18] solved the steady finite-chord problem for a permeability that varies along the chord, and Baddoo et al. [4] extended the analysis to unsteady flow. They derived porous counterparts of the four classical unsteady functions: the Theodorsen and Sears functions for harmonic oscillation and sinusoidal gust encounter, and the Wagner and Küssner functions for the corresponding indicial responses. The present analysis borrows its essential device from Baddoo et al. [4]. At a permeable leading edge the load is still singular, but more weakly than the inverse square root of a rigid edge. Its exponent falls below by an amount set by the local permeability, and returns to only where the surface is impermeable. A Chebyshev (Glauert) expansion builds in the rigid exponent and cannot represent this behaviour, whereas a family of Jacobi polynomials whose weights carry the correct exponents at the two edges can. Ayton et al. [3] treated chordwise-varying porosity by a Wiener–Hopf-based approximation over the same frequency range.
Every one of those finite-chord treatments is incompressible, and the question is whether that matters. For a rigid aerofoil the answer has long been known. Consider a section of chord in a stream of speed , with sound speed and Mach number , responding at angular frequency , so that its reduced frequency is and the acoustic wavenumber is . Incompressible gust theory requires the chord to be acoustically compact, ; beyond that the loading is no longer in phase along the chord, and the compressible response departs from Sears’s function by more than a correction [17, 33, 1, 24]. The incompressible theories are the limit at fixed and so describe a compact chord at any speed, since compactness is a condition on , not on . The surfaces to which permeable edges are applied lie well outside that range, because they move fast through disturbed flow. A rotor blade meets its own wake, a neighbouring rotor’s wake and the ambient turbulence once per revolution. At –, ingesting turbulence or passing through a tip vortex, it is loaded at –, so lies between and , and on the advancing side of a high-speed rotor, where the local Mach number reaches –, the impulsive part of the loading dominates what is radiated [23]. A wing or fan blade at high subsonic speed that meets atmospheric turbulence or the wakes of surfaces upstream is in the same position: a gust whose wavelength equals the chord has , so at – the product is already 1.6–2.2, and shorter gusts give larger values. Even a low-speed aerofoil is non-compact once approaches , about 20 at , which is within the range that turbulence-interaction and blade–vortex-interaction loading models must cover. In each case the unsteady load is the input to aeroelastic and acoustic predictions. For rotors and propellers it drives both the tonal and the broadband parts of the signature, frequency-domain load models are what make the prediction tractable at design time [15], and the spread in predicted hovering-rotor noise that follows from gust-induced unsteady loading is large enough that the loading model, not the acoustic propagation, sets the uncertainty [14]. A treatment of such a surface therefore has to be assessed in compressible flow, at finite chord, with the wake retained.
For a permeable aerofoil it is not known whether incompressible theory remains adequate outside the compact range, and there is no reason to expect the rigid criterion to carry over. The pressure jump across a rigid surface is set entirely by the surrounding flow, which is where compressibility acts. Across a permeable surface it is set partly by the surrounding flow and partly by the material impedance, which fixes the pressure jump needed to drive fluid through the surface, and the balance between the two shifts with permeability. How permeability controls the sensitivity of the unsteady loading to compressibility, and how compressibility changes the load of a porous aerofoil relative to that of an impermeable one, which is how a treatment is judged, are the questions a compressible theory has to answer.
At the compressible end, Hales et al. [19] formulated a semi-infinite permeable edge in compressible flow with the grazing-flow conductivity of Howe et al. [21]; being a half-plane theory it carries neither the finite chord nor the wake. The combination that is missing (Table 1) is the subject of this paper: a finite chord in compressible flow, with an admittance (the reciprocal of the material impedance) that varies arbitrarily along the chord, and with the wake and the Kutta condition.
Table 1. Table 1: Analytical treatments of a permeable aerofoil surface. “Partial” records a theory formulated for compressible radiation from an incompressible near field.
This paper develops a linear theory for the unsteady loading of finite-chord porous aerofoils in compressible subsonic flow. It combines Possio’s integral operator with a convective permeable boundary condition, allows the admittance to vary along the chord, and retains the shed wake and the unsteady Kutta condition. Three things change in passing from the incompressible formulation to the compressible one, and one does not. The integral operator becomes Possio’s rather than Cauchy’s, and its compressible part acts on the jump in velocity potential itself and not only on the bound vorticity, so the compressible solver must carry both where the incompressible one closes on the vorticity alone. The permeable boundary condition becomes convective, so that the permeability parameter (§ 2.2) carries the Mach number. And the reduced frequencies are stretched by the Prandtl–Glauert transformation, so that the ratio of the chord to the acoustic wavelength enters as well as its ratio to the hydrodynamic one. What does not change is the local behaviour at the aerofoil edges and at admittance discontinuities. The non-Cauchy part of Possio’s operator is bounded, so it cannot alter the exponents that a Riemann–Hilbert analysis assigns there, and the loading exponents retain their incompressible functions tional form when expressed in terms of the local permeability parameter (§ 2.5). This is what allows the weighted-Jacobi collocation method of Baddoo et al. [4], including their treatment of interior admittance discontinuities, to be carried over at the cost of a rigid calculation. The solution is verified against published incompressible results and against an independent compressible formulation in physical variables (§ 4). The formulation contains the classical theories as limits: with it is Possio’s problem, and for it reduces to the functions of Theodorsen, Sears, Wagner and Küssner; with and it is the incompressible porous theory of Baddoo et al. [4]. Each limit is verified in § 4.
The theory is then used to examine how permeability controls the sensitivity of the unsteady loading to compressibility (§ 6). Incompressible and compressible responses are compared for the same material and reduced frequency, both where the chord is acoustically compact and where it is not, and at low as well as high Mach number, since compactness is set by rather than by (§ 6.3). The two routes by which the Mach number reaches a permeable surface, the boundary condition and the integral operator, are separated. The shortcut of combining the existing incompressible porous and compressible rigid theories is tested against the full solution, and the condition under which it is adequate is derived. The harmonic gust and heave responses, the porous counterparts of the Sears and Theodorsen functions, are computed together with their indicial counterparts, the porous Küssner and Wagner functions, and the steady and high-frequency limits are obtained in closed form. The aim is compressible loading predictions for assessing porous aerofoils and for supplying aerodynamic inputs to aeroelastic and aeroacoustic models.
The paper is organised as follows. Section 2 formulates the problem and derives the edge and junction exponents; § 3 describes the solution; § 4 verifies it against classical, closed-form and published results; § 6 compares the compressible and incompressible responses; and § 7 draws conclusions.
Formulation
The problem
Figure 1 shows the configuration and the notation used below. Three features of the configuration drive everything that follows. The permeable region has ends, so the problem carries interior discontinuities in boundary condition as well as the two aerofoil edges, and § 2.5 shows that each carries its own algebraic singularity with exponents that are not independent. The trailing edge carries a shed wake and the unsteady Kutta condition, so the circulation is fixed by the solution. And the admittance is a function of position, not a constant: a manufactured insert has a definite extent, and the grazing flow that sets the admittance of a perforate varies along it.

Figure 1. The configuration and the three exponents. A thin section of chord in a stream of Mach number carries a permeable region of length , across which the admittance enters through alone; here the region begins at the leading edge and ends at a junction , but the formulation admits any distribution, including a permeable trailing edge. The loading is singular at the leading edge and at the junction, bounded at the trailing edge, and each exponent is an inverse cotangent of the local (§ 2.5). The wake and the unsteady Kutta condition make the circulation part of the solution rather than a free parameter. A semi-infinite formulation cannot represent this, and it is what makes the chord enter the answer.
A thin aerofoil of chord lies along , , in a uniform stream of an ideal fluid of density and sound speed , at Mach number and Prandtl–Glauert factor . The surface is permeable, with a transfer admittance that may vary along the chord. The disturbance is harmonic with the convention ; we write for the acoustic wavenumber and for the hydrodynamic one. The canonical forcing is the frozen transverse gust , but the formulation admits any imposed upwash, and § 2.4 lists the three that are used here.
The Prandtl–Glauert transformation (appendix § 14) maps the problem to a Helmholtz problem of wavenumber on a plate of half-length . Normalising the chordwise coordinate on that stretched half-length, , the two reduced wavenumbers each pick up twice,
Both are dimensionless. is the phase, in radians, that a sound wave of the transformed problem accumulates across its half-chord , and so measures acoustic compactness; is the corresponding phase of the convected gust. Equivalently, the chord spans acoustic wavelengths. The classical reduced frequency is , and results are reported in so that they may be read against the classical functions directly.
The permeable boundary condition
The surface is modelled as a homogenised sheet of vanishing thickness across which the pressure jump , upper surface minus lower, drives a seepage velocity , positive in the direction. Writing the normalised transfer admittance through
so that fluid passes from the side at higher pressure to the side at lower pressure. Mass conservation across the sheet requires the normal velocity of the fluid relative to the surface, the imposed upwash plus the disturbance velocity , to equal the seepage velocity on both faces, which gives
the second form following from the linearised momentum relation , with the jump in velocity potential. Written this way the condition is convective: the seepage is proportional to the material rate of change of the potential jump seen by the mean flow, and not to the potential jump itself. The convective operator sits in the momentum relation rather than in the material law (2.2), which is why much of the porous-media literature, working at , sees only . The two conditions coincide only when . The convective derivative comes from the linearised Bernoulli relation, which carries it in incompressible flow as well, so it is not removed by letting at fixed .
With harmonic time dependence and lengths scaled on the stretched half-chord, the material enters the integral equation of § 2.3 through a single dimensionless group, the permeability parameter
which multiplies the pressure jump there. A rigid surface has , a fully transparent one , and a chordwise distribution of material is a function . Appendix § 13 gives the derivation and shows that , being a ratio of the seepage coefficient to the Cauchy coefficient, does not depend on how the unknown is normalised. It also shows how the condition relates to the static condition of Jaworski and Peake [22] and Ayton et al. [3]: holding the porosity parameter fixed as keeps finite, but the static condition is recovered only when, in addition, the convective derivative is dropped.
Relation to the porosity parameter of Baddoo et al. [4]. Their , with the dimensionless resistance, the effective density of the pore fluid and their reduced frequency, equal to , is the same quantity as , written in the time convention and for a specific material law. The identification is not an analogy: it is an equality of the coefficient multiplying the loading in the two governing equations, it is confirmed numerically in § 4 across the full unsteady range, and it is why their exponent formula and ours are the same function. In the present convention the same material is the conjugate, .
Reduction to a singular integral equation
Representing the aerofoil and its wake by a dipole sheet whose strength is the jump in potential, taking the pressure jump as the unknown, and enforcing (3) on the mean surface yields, after the Prandtl–Glauert transformation,
where is the pressure jump, non-dimensionalised so that the Cauchy coefficient is , and is a bounded remainder. The bar on the integral sign denotes the Cauchy principal value,
which exists because is Hölder-continuous on any closed subinterval of that contains no admittance junction, and is integrable across the junctions (§ 2.5). The operator is the Possio kernel (Possio [34]): appendix § 14 derives (5) from the convected wave equation and shows that its singular part is exactly the Glauert Cauchy kernel, while the remainder consists of the regularised Hankel function , which is bounded, together with terms whose kernels are at worst logarithmically singular. Each therefore maps a Hölder-continuous to a bounded function, which is all the analysis below requires; is a bounded operator rather than a bounded convolution kernel. It includes the wake, which enters through the circulation; at the trailing edge the chord and wake contributions each carry a logarithm, and appendix § 14 shows that the two cancel, so that stays bounded there too.
Two auxiliary conditions close the problem: Kelvin’s theorem, relating the bound circulation to the shed vorticity, and the unsteady Kutta condition, which requires the loading to be bounded at the trailing edge. On a rigid aft section the latter is , or a permeable one it is with given by (10) below, which is weaker but still bounded.
Provenance. The equation is assembled from two independent ingredients and is not inherited whole from any previous paper. The integral operator is the compressible thin-aerofoil operator of Possio [34], unchanged. The term is what the permeable boundary condition (3) contributes, and is derived in appendix § 13. The relation to the incompressible equation of Baddoo et al. [4] is a change of dependent variable together with the loss of the Hankel remainder: they carry the bound vorticity , so their algebraic term appears as , a Volterra contribution which is exactly their pressure jump, and writing the equation in from the outset absorbs it. Setting removes both Hankel terms, and what remains of is precisely the bounded term generated by the change of dependent variable; the present equation and theirs are therefore the same equation written in different variables. Both are dominant-singular equations with a variable coefficient, which is why they share edge exponents.
The forcing
is the forcing of (5) and the only place the incident flow enters. It is the physical upwash , normalised on its amplitude, with the sign it carries in (3). Equation (5) is written for the transformed potential of appendix § 14, , so enters it multiplied by :
The heave upwash is normalised on the plunge velocity and the pitch upwash on times the pitch amplitude, whose two terms are the incidence and the pitch rate. The sign is the statement that the surface must cancel the imposed upwash, up to whatever seepage permits. For the gust the two exponentials combine, , into : in the transformed variables the gust convects at , the wavenumber at which the wake convects in every case. In the heave and pitch problems too, enters through the wake and through the loading of (19), not through the forcing. The gust phase is referred to the leading edge, , and not to the midchord: this costs nothing in the frequency domain but is essential when the transfer function is inverted to the time domain, since a midchord reference makes the response begin before the gust arrives. The indicial responses are not a fourth forcing: they are the heave and gust responses carried into the time domain (§ 3.4). In every case the Kutta and Kelvin closures of § 3.2 are unchanged.
The same factor appears, inverted, in the output. is the transformed loading; the physical pressure jump, upper surface minus lower, is , and the lift is
the sign because a lifting section carries the lower pressure on its upper surface. The steady lift of appendix § 17, , is the same statement. With the normalisation of appendix § 13, , the lift per unit span is , so that on the basis used in § 6, the incompressible quasi-steady lift of the rigid plate, the load is . The factor has unit modulus, so it leaves the magnitude of the loading, and with it every exponent of § 2.5, unchanged; it does not enter the permeable term either, since (2) relates the seepage to the pressure jump at the same point and the factor multiplies both. It does change the lift once is of order one, and a check that it has been carried consistently is the high-frequency limit of the heave response, which must approach the acoustic (piston) value, times the compressible quasi-steady lift (Table 2).
| test | reference | error |
| Basis at | , | |
| Possio symbol, – | , closed form | |
| the same, as assembled in § 3 | the same, by quadrature | |
| Sears function, – | ||
| Heave response, – | (incl. apparent mass) | |
| Heave, –, – | piston limit, and (26) for – | rel. |
| Steady lift, – | , closed form (27) | |
| Seepage drag | , closed form (28) | |
| Porous quasi-steady, – | , from the unsteady solver | |
| Junction invariance on a rigid plate | must be exactly unity | |
| Edge exponent read off the solution | (9), –, | rel. |
| Junction exponent read off the solution | (11), and | rel. |
| Generalised basis at | the rigid-trailing-edge basis | bit-identical |
| Mode count, , | default against | |
| Steady lift, – | Baddoo et al. [4] eq. (3.1), solved independently | |
| Unsteady, , – | Baddoo et al. [4], their published code | |
| Rigid, –, – | physical-variable solution, appendix G | |
| Permeable, , , – | the same | |
| Independent reimplementation | MATLAB vs PYTHON | |
| Loading/potential identity | (19), evaluated on every solve |
Table 2. Table 2: Verification tests. is the incidence, not the trailing-edge exponent. is Theodorsen’s function in the convention, , and the Sears phase is referred to midchord. The second row is the most sensitive test of the quadrature; the last is the only one available at no cost on every solve.
An oblique gust, with spanwise wavenumber , does not require a new formulation either: the factor is a parameter of the two-dimensional problem and enters only by replacing the acoustic wavenumber with , the branch chosen so that . This matters for the acoustic use of the theory and is recorded here for completeness; all results below are for .
Edge conditions
Equation (5) is a dominant-singular equation with a variable coefficient. Its solution is not smooth, and the local exponents are set by the coefficient.
Near an edge the bounded part of the kernel is subdominant and (5) reduces to the dominant equation on a half-line with constant coefficient. This is a Riemann–Hilbert problem [32, 12]. Writing the sectionally analytic function and applying the Plemelj formulae gives (forcing) with
Setting makes , and the canonical solution then behaves as at the leading edge. Hence
At the trailing edge the same construction with the admissible (bounded) branch gives the exponent of the vanishing rather than of the singular behaviour,
so that a rigid aft section, , recovers the classical , and a permeable one vanishes more slowly. Both exponents are local: each is evaluated with the value of at its own edge, and neither depends on the rest of the distribution.
Two limits check (9). As , and the classical inverse-square-root singularity is recovered. As , and the loading is bounded: a fully transparent edge scatters nothing and carries no suction. Between them falls monotonically (Figure 2). For complex , as for a material with inertia, (9) is analytic except at the branch points . These lie on the imaginary axis and are reached only by a lossless inertive layer, at the single frequency where ; any resistance, , keeps clear of them.
Figure 2. (a) The leading-edge exponent of (9). (b) The loading singularity it produces. A Glauert basis imposes , valid only for .
Compressibility does not change the exponents, and this is not automatic. The compressible kernel of (5) is not a Cauchy kernel. What the argument above uses is that its non-Cauchy part is bounded (appendix § 14), so it is subdominant in the local analysis and cannot enter . The exponents are therefore fixed by the dominant singular part alone, are independent of , and coincide in form with the incompressible exponents of Baddoo et al. [4]; Hajian and Jaworski [18] reached the corresponding steady result by the same route. The Mach number reaches the exponents only through , and more weakly than suggests. Since the explicit cancels, and for the same , and material what remains is the Prandtl–Glauert factor, , whatever the material (§ 2.6).
The junction exponent. At an interior point where jumps, such as the junction between a porous insert and the rigid remainder or between two materials, the same argument applies with a piecewise-constant coefficient. The Riemann–Hilbert coefficient jumps from to , and the canonical function acquires a local exponent
with . For the common case of a porous insert ending on a rigid aft section this is : moving downstream into a less permeable section makes the loading singular, and the junction acts as the leading edge of the aft section. Moving downstream into a more permeable section, as from a rigid forward section onto a porous aft one, gives , and the loading vanishes there as , as at a trailing edge, as found by Baddoo et al. [4]. For on both sides, and the junction disappears, which is why inserting a junction into a rigid plate must change nothing; this property is used as a numerical test in § 4. For on the forward side, , the inverse-square-root singularity of a rigid leading edge. Since the squared loading remains integrable and the energy is finite.
The permeability parameter
Because is the only route by which the material enters, its parametric dependence can be read off before (5) is solved. Two statements follow, and both are testable.
The semi-infinite version of (5) admits the Wiener–Hopf kernel
in which is the chordwise wavenumber scaled on , for the transform , and the material enters only through . The permeable term vanishes at , the wavenumber of the frozen gust in the transformed variables, because a disturbance convected with the stream carries no pressure jump and so drives no seepage. This is a property of the kernel, not of the finite-chord response, which depends on the whole kernel and on the edges. Using ,
in which the Mach number appears only through . Substituting (13) into (12) gives , which tends to as at fixed and . The last term is the convective part of the boundary condition; the static porous half-plane kernel of Jaworski and Peake [22], , is recovered only when it is dropped, as at . The group controlling how porous a surface appears to a gust is the ratio of the porosity parameter to the hydrodynamic wavenumber , not to the acoustic one. For a material whose does not depend on frequency, such as an inertive perforate, falls as , and , where the seepage and flow terms of (5) carry equal weight and , defines a porous cut-off frequency , linear in speed, above which the surface appears increasingly rigid. For a lossless perforate this is the branch point of §2.5; a resistive layer, whose is proportional to frequency, has no cut-off.
What compressibility does and does not do to . Write the material law through the dimensional transfer impedance , so that . Then (4) becomes
and the explicit factor in (4) is cancelled by . When the compressible and incompressible theories are compared for the same flow, at the same , and material with the sound speed as the only difference, is therefore fixed and the whole Mach dependence of the boundary condition is the Prandtl–Glauert factor, for any material: rises by at and by at . That is the comparison made in §5. Everything else compressibility does acts through the kernel and the Prandtl–Glauert transformation, that is through , and the of the quasi-steady lift. The factor in has the same size as the Prandtl–Glauert rise of the rigid lift and the opposite effect, since a larger means a weaker load, and §5 shows that the two cancel in the steady, strongly permeable limit. The frequency dependence of is set by the material. A resistive layer, , has a real independent of frequency. An inertive perforate, with an effective mass per unit area, has , imaginary and varying as . A layer with both, the form of the material law of Baddoo et al. [4], passes from the first behaviour to the second as the frequency rises. If the Mach number is instead raised by raising in the same fluid, for a resistive layer, and is fixed at fixed for an inertive one.
Acoustic non-compactness. The kernel carries the second compressible parameter, of (1), the acoustic phase across the half-chord. It enters through the Hankel functions of (B.2): the upwash induced at by the loading at arrives with the phase of a sound wave that has crossed the distance between them, so for the kernels oscillate like and different parts of the chord act on one another with phase lags of order a radian or more. The term in , which acts on the potential jump itself, has no incompressible counterpart. Incompressible flow is the limit , in which , the Hankel kernels reduce to the Cauchy kernel and the retardation disappears; what remains is the hydrodynamic scale of the convected gust and the wake. The two compressible parameters are independent. The Mach number enters the boundary condition through , and the forcing through the phase of (6); enters the kernel and does not depend on the material at all. At low Mach number the first is negligible and the second is not, since is of order one whenever is of order (§5.3).
Material-class scaling. Equation (13) makes depend on the material only through , and the two classes scale oppositely. For an inertive perforate is a purely geometric inverse length, is imaginary, and
a function of the Strouhal number and the perforate geometry alone. For a resistive bulk layer carries no factor of , so and
frequency-independent and linear in ; this is the parameter by which Geyer et al. [13] organised sixteen porous aerofoils. A perforate therefore collapses on and a bulk medium on ; the two predictions are of opposite sign and follow from the same boundary condition.
Solution
The weighted-Jacobi basis
Equation (5) is solved by collocation in a weighted-Jacobi basis built on the exponents of § 2.5. The idea of replacing the Chebyshev (Glauert) family by Jacobi polynomials whose weights carry the porosity-dependent exponents is due to Baddoo et al. [4], who introduced it for the incompressible problem and treated an interior discontinuity by splitting the chord there into two sections, each with its own weighted-Jacobi expansion carrying the junction exponent (their § 3.3). What is new here is that the method transfers unchanged to the compressible kernel, for the reason given in § 2.5. At a junction we keep a single basis on the whole chord and add two junction modes (18) that carry the same local exponent. The basis is
with from (9) and from (10), and the last member representing the wake. The aerofoil modes and all carry and so vanish at the trailing edge; the wake mode does not (), because it carries the vorticity leaving the edge. The Kutta condition is therefore a property of the combination the solve selects rather than of each member separately, and it is satisfied without an extra equation (§ 3.2). At the family collapses exactly onto Glauert’s, and with , which is the first of the verification tests of § 4. At each junction two further modes are added,
spanning the two-sided local solution of (11). Their envelope vanishes at both plate edges, so the leading-edge exponent and the Kutta condition are untouched.
Figure 3 shows what the exponents do to the basis. At the members are the classical Glauert modes, reproduced here to (Table 2); at every member is visibly weaker at the nose while remaining identical at the trailing edge. The difference cannot be produced by adding Glauert modes: no finite combination of functions singular as reproduces , which is why the exponent must be built in rather than resolved. The same argument applies at a porous trailing edge, where , and at a junction, where the singularity is interior.
Figure 3. The basis, each mode normalised by its largest value away from the nose. (a) At the weighted-Jacobi family reduces exactly to Glauert’s. (b) At the nose behaviour is weaker, while the trailing edge is unchanged. (c) The two junction modes {(xref)}(3.2) carrying . The trailing-edge exponent enters the same way, through the weight common to every aerofoil mode.
The linear system
The working unknown. Equation (5) is written in , but is a derivative combination of the jump in velocity potential across the sheet. Let be that jump, scaled by the same constant as so that is the circulation. Substituting into with the convention gives
in which is the bound vortex-sheet strength. The two terms carry opposite signs: the first is the quasi-steady loading a stationary vortex sheet would carry, the second the contribution of the unsteady rate of change of the potential jump. Their partial cancellation is why the unsteady lift falls below its quasi-steady value as grows, and the Sears and Theodorsen checks of {(xref)}§4 test exactly this combination. The potential jump is expanded in preference to for three reasons.
Both and appear. In compressible flow the normal velocity the sheet induces at has two parts: a vortex-sheet part driven by , which supplies the Cauchy kernel together with an correction, and a compressibility part driven by itself, of order . The second vanishes as , which is why the incompressible problem closes on the vorticity alone and the compressible one does not.
The wake and Kelvin’s theorem are statements about , which is a functional of and is carried here as an explicit unknown.
The time-domain inversion of {(xref)}
§3.4and the radiation integral both act on , so solving in needs no further differentiation of the answer.
Expansion. The basis {(xref)}(3.1) and the junction modes {(xref)}(3.2) span , which carries the singular part of and therefore the exponents of {(xref)}§2.5; the expansion of itself uses their antiderivatives, taken from the trailing edge, , and , all of which vanish at so that . Then
and follows pointwise from {(xref)}(3.3). The wake coefficient is not independent: the wake carries for , so continuity of across , which means no concentrated vortex at the edge, fixes . That single tie makes the Kutta condition automatic rather than imposed, because (19) then gives
identically, for every , every porosity and every trailing-edge exponent . The are available in closed form through a Jacobi identity; the are not, because carries the interior algebraic singularity, and they are evaluated once per junction by cumulative quadrature on a graded grid. The unknown vector is : numbers for junctions, with set automatically and raised where the admittance distribution has interior kinks (§ 4).
Collocation and closure. Substituting (20) into (5) and enforcing it at points , , gives rows; the variable coefficient enters simply as on the diagonal, which is why an arbitrary costs nothing. Kelvin’s circulation theorem supplies the one remaining row. For a closed material contour that at lay in undisturbed fluid and encloses the aerofoil together with all the vorticity it has shed, the circulation cannot change ([5]), so
The two auxiliary conditions act at opposite ends of the plate and play distinct roles: Kutta fixes the behaviour of the solution at , through the basis; Kelvin fixes the amount of circulation at , through the one extra row. The result is a square system, solved directly.
Two consequences follow. First, the cost is that of the classical rigid problem: the same number of unknowns, the same quadrature, one dense solve. Porosity changes the exponents in the basis functions and the diagonal, not the size or the structure of the matrix. Second, a basis without the right exponents fails in a specific way: omitting (18) removes the only columns able to represent , and the remaining columns then fit the collocation data as well as they can, so the error stops falling well short of zero, at a level set by the missing function. That is the 1–5 % stall found in § 4, and it is a statement about the span of the basis rather than about the number of modes.
Quadrature
No closed-form Hilbert transform of the weighted-Jacobi family is needed. The Cauchy singularity is removed by subtraction,
after which Gauss–Legendre panels graded towards the singular points suffice. The panels must additionally be subdivided so that no panel spans more than , with Gauss points per panel, otherwise the oscillation of the high-order modes is aliased; without this refinement the junction-invariance test of § 4 returns a 7 % error. Details are in appendix D.
Indicial responses
The Wagner and Küssner functions are the time-domain counterparts of the Theodorsen and Sears functions, and they are what an aeroelastic, gust-load or blade–vortex-interaction calculation actually requires. They are obtained here by inverting the computed transfer function rather than by solving a separate problem. Let be the lift response to the harmonic forcing of (6) at reduced frequency , normalised on its quasi-steady value. The indicial response to a step of the same kind is
being semichords travelled, the standard inversion [6] valid because is the transfer function of a causal, stable, real system. Two properties of the present formulation matter for it. The gust phase is referred to the leading edge (6), so the Küssner response starts at rather than at ; and the apparent-mass part of the heave response, which is an impulse at and in the rigid limit, is removed before inverting, since Wagner’s function describes what is left. Both the subtraction and the tail of (24) beyond the computed range are given in appendix § 18; the end-to-end accuracy of the scheme is the 0.007 with which it reproduces the classical Wagner function (§ 6.6).
Verification
Table 2 lists the verification tests. They fall into three groups: tests of the machinery that the rigid theory shares (the first six rows), tests of the porous terms against closed forms and against the exponents they are built on (the next eight), and tests of the assembled solver against independent implementations (the next five); the last row is a consistency check made on every solve. The sixth row is the only classical check made at finite Mach number: at high reduced frequency the loading of a heaving plate approaches the acoustic value , which is times the compressible quasi-steady lift. The test is sensitive to the Prandtl–Glauert factor of (6) and (7): omitted from both, it returns 1.28 at in place of 1.10. For a permeable plate the same argument, with flow through the material as a second path in parallel with the piston motion, gives the limit (26) of § 6.2, which the solver reproduces to at .
The compressible operator. All the classical checks except the piston limit are made at , where the term and the regularised remainder vanish, so they do not test the compressible part of the operator. That part is verified directly, through its Fourier symbol: on an unbounded sheet, a potential jump must induce the normal velocity , with and , which is the exact response of the Helmholtz problem (B.1). Applying (B.2) to , with and the transforms
gives , as required. Because the identity must hold for every , it tests each Hankel term and their relative coefficient separately, which a comparison with a tabulated lift coefficient would do only indirectly. It is satisfied to in closed form, and to by quadrature over –10 and –8, both directly and through the split into a Cauchy principal value, the regularised and that § 3 assembles. End to end, the solver approaches the classical Sears function continuously as at fixed : the difference falls from at to at , at the rate of the small-argument expansion of the kernel, and reaches the solver’s own floor of by . Figure 4 shows the resulting agreement with the Sears function over –8.
Figure 4. The rigid, incompressible limit against the Sears function. Lines, the classical function [35]; symbols, the present solver at , with the phase referred to midchord. The difference is below over –.
An independent solution at finite Mach number. The Fourier-symbol test verifies the operator and the tests verify its limit, but neither tests the assembled compressible solution, and the Prandtl–Glauert factor of (6) and (7), which is invisible at , has so far been tested only in the high-frequency heave limit. The assembled solution is therefore compared with a second solution of the same physical problem (appendix G). Its unknown is the physical pressure jump rather than the transformed potential, it has no wake and no Prandtl–Glauert transformation, and the kernel is applied through its exact Fourier symbol in physical variables; only the edge exponents of § 2.5 are common to the two methods. The absolute difference in the lift is at most for a rigid plate over – and –, and at most for permeable plates with and over –, in magnitude and phase and for both the gust and the heave forcing. The larger rigid-plate difference comes from truncating the wavenumber integral of the second method (appendix G), not from the first.
The incompressible limit: comparison with Baddoo et al. [4]. Setting in (5) removes the terms and the Possio kernel collapses to the Cauchy kernel alone, so the equation becomes the incompressible singular integral equation of Baddoo et al. [4] with in the role of their porosity parameter; the exponents (9), (10) and (11) are independent of and so are already common to both. Their results are therefore the limit of the present solver, and the results of § 6 are its continuation in . That claim is checked in three increasingly demanding ways.
First, structurally, in the steady limit: their equation (3.1) was discretised from scratch in their variable, the bound vorticity, and in their basis, sharing no code with § 3, and its circulation reproduces to .
Second, in the unsteady quasi-steady limit, where the solver is asked for limits it was not constructed to satisfy: with a heave forcing returns to over , so the circulatory and non-circulatory parts of the classical response are both recovered; with the quasi-steady limit of the unsteady solution returns to over –, for heave and gust forcing alike.
Third, and most stringently, against their published code itself (https://github.com/baddoo/unsteady-porous-aerofoils), run on the porosity profiles exactly as their figure 10 is generated: an impermeable leading edge, ramping linearly to over of the chord from and constant thereafter, so that the trailing edge is porous, and . Their is written for the time convention , so in the present convention the same material is its complex conjugate; the porosity supplied to the present solver and the lift it returns were both converted accordingly before the two codes were compared. Figure 5 shows the result. The ratio , which is free of any normalisation or phase convention, agrees with their code to within on all four profiles over –, with no growth in (, , and for the four ramps); the impermeable control agrees to . This is point-by-point agreement with an independent implementation of the limiting case, on configurations chosen by its authors rather than by us, and it includes a porous trailing edge, , which exercises (10). The features Baddoo et al. [4] report are reproduced with it: grows with permeable length, and the porous phase curves cross the impermeable one, here at –, the crossover moving to lower frequency as the permeable length grows (Figure 5c). On the impermeable curve the present solver reproduces their closed form (6.3) to .
Figure 5. The present solver at (lines) against the published code of Baddoo et al. [4] (open symbols), on the porosity profiles of their figure 10: an impermeable leading edge, rising linearly from zero at to 0.5 at , ; black, impermeable. Each curve is normalised at , as their figure is. (a) Argand diagram, (b) magnitude and (c) phase of the porous Sears function, laid out as their figure 10. (d) The relative difference between the two codes in the ratio , which is independent of normalisation and time convention; the dotted line marks 0.1 %. Both codes at their converged basis size: here, in theirs.
Convergence and the junction modes. The decisive convergence result concerns the junction modes (Figure 6). For a permeable insert with over the forward of the chord at , the lift computed without the junction modes wanders at the – level and does not settle as is raised from to : the expansion converges, but not to the right answer, because a global basis cannot represent an algebraic singularity at an interior point. With them the error settles at a few times , an order of magnitude better and still falling, and the remaining level is the price of representing with two modes rather than a local expansion. Raising the quadrature resolution of the junction modes by a factor of six changes nothing, so this is a basis limit and not a quadrature one. The
Figure 6. (a) Convergence of the lift with and without the junction modes (18), for a permeable insert over the forward 30 % of the chord, , ; the reference is the same solver at . (b) The complementary test: a junction placed on a rigid plate, where , must change nothing.
Results
asymmetry between the two curves is the numerical statement of (11): a basis that does not carry the junction exponent cannot converge to the solution, which is why Baddoo et al. [4] split the chord at a discontinuity and why the junction modes are added here. The complementary test is exact rather than approximate, and it is the sharpest test of the quadrature: a junction placed on a rigid plate, where and the modes must vanish, must change nothing, so any residual is discretisation error. It changes the lift by over –. A smoothly varying with interior kinks, such as the ramps of Figure 5, converges more slowly than a piecewise-constant insert with explicit junction modes, so the default mode count must be raised there. suffices over , and raising the count from the default to 60 takes the comparison of Figure 5 from 0.63 % to 0.09 %. The remaining difference is at the level expected of two independent spectral discretisations rather than a property of either.
Results
All results below are for a uniformly permeable plate or for a permeable insert of length at the leading edge, with quoted directly rather than through a particular material, so that they apply to any surface with the same . Unless stated otherwise the surface is a resistive layer: is real and independent of frequency, and the compressible and incompressible responses are compared at the same , and , so that by (14) and the sound speed is the only difference. A layer with inertia as well as resistance is considered in §5.7. Reduced frequency is the classical throughout. Loads at finite Mach number are reported on a single basis, the incompressible quasi-steady lift of the rigid plate, per unit span, rather than on the compressible one, . The Prandtl–Glauert rise is therefore kept, so that a rigid plate at low frequency reads rather than unity, and a change with Mach number is a change in the load itself.
The loading at a permeable edge
Figure 7 shows the chordwise loading. Three things in it are worth separating, because they are usually run together.
Figure 7. Chordwise loading, uniformly permeable plate, at (a) and (b) ; solid , dashed with the same material, so that ; colour and the legend give . (c) A permeable insert over the forward 30 % of the chord, , : the nose singularity is weakened and a junction singularity appears at the dotted line.
The exponents are in the solution, not only in the basis. Fitting over the three decades returns , 0.3527, 0.1478 and 0.0396 for , 0.5, 2 and 8, against 0.5000, 0.3524, 0.1476 and 0.0396 from (9), which is agreement to three figures; at and , where , the agreement is still within 2 %. That the fit reproduces (9) at finite is the numerical counterpart of the analytical statement of §2.5: the compressible part of the kernel is subdominant at the edge and does not touch the exponent. At the junction of a finite insert the same fit returns against 0.3976 from (11) at , and 0.4096 against 0.4105 at .
The same material gives a weaker singularity at higher Mach number. Because , a surface with presents at , and the fitted exponent falls from 0.148 to 0.130. Nothing about the material has changed; the exponent has, by 12 %. A rigid edge has a Mach-independent singularity and a permeable one does not, which is a statement no static permeability condition can make.
The loading redistributes as much as it falls. Panels (a) and (b) are plotted logarithmically because the interesting comparison is not the peak but the shape: as rises, the nose loading collapses while the aft loading is left almost untouched, so the centre of pressure moves aft and the lift falls by less than the edge loading does. The finite insert in panel (c) makes the mechanism explicit. The insert weakens the nose, but the junction then carries and behaves as a second, weaker leading edge. That is why a treated nose does not simply remove the edge but moves a reduced version of it downstream. At , and the lift is 0.208 of the rigid quasi-steady value against 0.279 for a rigid plate at the same , a 25 % reduction for a treatment covering 30 % of the chord.
The porous Sears function at finite Mach number
What is held fixed as the Mach number varies is the flow speed, the frequency and the material, so that by (14) while grows from zero. Figure 8 is the result, and it separates cleanly into what is classical and what is not.
Figure 8. The porous Sears function at finite Mach number for a resistive layer, compared at the same flow speed, frequency and material so that . Every load is referred to the incompressible quasi-steady lift of the rigid plate. (a) for (solid) and for a rigid plate (dashed), coloured by Mach number. (b) The fraction of the rigid load that survives the treatment; the curve is what an incompressible theory would predict. (c) The Mach factor for , 1 and 3, at (solid) and 0.5 (dashed). (d) The two channels at against Mach number: the full response (filled symbols), the response with only varying, the response with only the kernel varying, and the rigid plate, for which only the kernel acts; circles , triangles .
The rigid response is the classical one. Compressibility raises the rigid load at low frequency by the Prandtl–Glauert factor, at and 1.40 at , and collapses it once the chord is no longer acoustically compact: at the load at is 0.32 of its incompressible value, and at it is 0.25 (panel a, dashed). Above the collapse carries shallow interference minima, at for , 8.8 and 18 for , and 7.1 and 14.8 for , spaced so that , the phase a sound wave accumulates in crossing the chord with the stream, increases by very nearly from one to the next. None of this is new. It is the behaviour of Possio’s problem that the similarity rules of Graham [17], the approximate theories of Osborne [33], Amiet [1] and Kemp and Homicz [24], and the compressible indicial functions used in aeroelastic and rotor analysis (Leishman [28]) all describe; the present solver reproduces it, and the independent solution of appendix G reproduces the minima to . It is the reference against which the permeable results are read.
The permeable response depends on Mach number through its permeability. Panel (c) shows the Mach factor for , 1 and 3, and further cases at and 8 complete the picture. At and the load is 0.43 of its incompressible value for a rigid plate, 0.53 at , 0.66 at , 0.86 at and 0.95 at : compressibility changes the load of a weakly to moderately permeable surface by between a tenth and a half, and that of a very permeable one hardly at all. At the three compressible curves of panel (a) lie close to the incompressible one; over and the load changes by at most 16 % (near at ), and by 1–2 % in the quasi-steady limit, where the rigid load changes by 40 %. The sensitivity falls steadily as the surface becomes more permeable at high frequency and in the quasi-steady limit, where the same ratio is available in closed form (§ 6.7) and interpolates between the Prandtl–Glauert factor of the rigid plate and unity. Compressibility therefore matters for a permeable surface, but by an amount and with a frequency dependence that neither the rigid compressible theory nor the incompressible porous theory supplies.
Why: the load of a permeable surface is set by the material. In the strongly permeable limit the surface simply passes the imposed upwash: the disturbance potential vanishes, the seepage velocity in (2.3) balances the upwash, , and the pressure jump is whatever the material needs to drive it through. By (2.2),
the second form following from (2.4) with . The flow around the surface does not enter, and with it neither does compressibility: (5.1) contains no . On the common basis of § 6, the incompressible quasi-steady lift of the rigid plate, it gives for the gust (Figure 8) and for heave (§ 6.4), at every Mach number. How the limit is approached is where compressibility enters, and for heave at high frequency it can be written down. Each face of the plate then radiates as a piston, with pressure times its normal velocity. The imposed upwash is taken up partly by this motion and partly by flow through the material, both driven by the same pressure jump, so the acoustic and material admittances add: eliminating the face velocity between the piston relation and (2.3) gives
which is the piston value for a rigid plate and the seepage limit as . The argument is local and holds for any material law, with evaluated at the frequency in question: for a resistive layer is constant and the load tends to a plateau, whereas for an inertive one and the load tends to the piston value of a rigid plate (§ 6.8). The solver reproduces (5.2) to four figures at and , and also at and for , 8 and 30, where the load lies , 8 and 2 % below the seepage limit. The high-frequency Mach sensitivity is therefore of first order in , whereas the steady one (§ 6.7) is of second order. For the gust the leading term is approached more slowly as grows, since the edges then carry more of the load, but its Mach independence is inherited: at the gust load changes by at most 1.4 % between and 0.7. The same limit explains the shoulder in every permeable curve near , where the chord average of the gust, and with it the leading term, vanishes. A rigid plate is the opposite extreme: its load is set entirely by the flow around it, which is where compressibility acts.
The two channels act in opposite directions. Panel (d) separates them at fixed , on the same basis. The boundary-condition channel, in which rises as while the kernel is held incompressible, lowers the permeable load by 22–24 % at , almost independently of . The kernel channel, which carries the Prandtl–Glauert rise, raises it by 23 % at and by 5 % at ; at the same kernel, acting on a rigid plate, lowers the load by 57 %. At the two cancel in part. The full change is 4 % at , 7 % at and 14 % at , where the kernel’s rise has faded, and the product of the two channels reproduces the full response to within 4 % for and 6 % at . The cancellation improves as the surface becomes more permeable: the full change is 2–5 % at over , and it is exact in the steady, strongly permeable limit (§ 6.7).
What the treatment is worth. The surviving fraction , the load of the treated plate divided by that of the rigid plate at the same and , is shown in panel (b). It is a ratio whose numerator hardly depends on Mach number and whose denominator carries the whole classical collapse. It therefore inherits that collapse. At low reduced frequency the incompressible theory is pessimistic: it gives 0.236 at where gives 0.217, and 0.332 against 0.301 at . The largest difference is the quasi-steady one: the compressible fraction is then the incompressible one times , which is 0.87 at and 0.73 at . The curves cross near at (1.5 at , 4.9 at ), and above that the incompressible theory is increasingly optimistic: at it predicts that 7.6 % of the rigid load survives where gives 21.6 %. Over the non-compact range –20, it underestimates the surviving fraction by a factor of between 1.4 and 4.2 at and between 2.0 and 4.3 at . The peaks of the compressible curves above sit just below the interference minima of the rigid response.
Can existing theories be combined? Because the permeable load depends on Mach number less than the rigid one, it is tempting to form the surviving fraction from two theories that already exist: the treated load from an incompressible porous theory, which is the limit of (2.5) solved by Baddoo et al. [4], and the reference load from a compressible rigid one. Figure 9 tests that shortcut against the full solution. The rigid load is then exact, so what is plotted is the error of the porous numerator, in two versions: the incompressible theory used as it stands, with the same (solid), and with the permeability parameter corrected by hand to (dashed). At low frequency, where the chord is compact, the first version is within about 20 %. Over the non-compact range –20 it overestimates the surviving fraction, and so understates the benefit, by factors of 1.45–1.96 at and 1.26–1.52 at when (1.34–1.68 and 1.20–1.35 at ), by 12–16 % at and by at most 6 % at . Correcting reduces the error for a weakly permeable surface but overcorrects a strongly permeable one, whose surviving fraction it underestimates by up to 35 % at and . It applies the boundary-condition channel of Figure 8(d) without the kernel channel that offsets it, and in the seepage limit it returns times the true load. The two versions err in opposite directions, and which of them is closer to the full solution depends on , and , so the better one cannot be identified without computing the compressible solution itself.
Figure 9. Can existing theories be combined? The surviving fraction estimated from an incompressible porous theory and a compressible rigid one, divided by the full compressible result, for resistive layers at (a) and (b) . Solid, the incompressible porous load with the same ; dashed, with . Values above unity understate the load reduction, values below overstate it; the shaded band is .
When the shortcut is adequate follows from the high-frequency limit (5.2). For heave at high frequency the incompressible porous load exceeds the compressible one by exactly , so the shortcut is within 10 % only if , that is –7 at –0.7; in steady flow the error is of second order in , by (5.6). Only for a strongly permeable surface, therefore, can compressibility be left to the rigid reference. For weakly and moderately permeable surfaces the compressible porous theory is needed for the load itself, and for every permeability it is needed for what a ratio of lift magnitudes does not contain: the phase, the chordwise loading and the Mach-dependent edge exponent of § 6.1, and the indicial responses of § 6.6.
Low Mach number, high frequency
The comparisons so far vary the Mach number at reduced frequencies of up to 20. The compressible parameter of the kernel is (§ 2.6), so a chord is acoustically non-compact at low Mach number too once approaches . Figure 10 takes , at which exceeds by 0.1 % and the phase of (6) is at most 0.3, so that the boundary condition and the forcing are effectively incompressible, and extends the gust response to , where and the chord spans about two acoustic wavelengths. What separates each pair of curves is then the acoustic non-compactness of the chord alone.
Figure 10. Acoustic non-compactness at low Mach number: resistive layers at , compared with the incompressible solution at the same , and material (the same solver at ). (a) The surviving fraction for a uniformly permeable plate and a leading-edge insert over 30 % of the chord, ; solid , dashed incompressible. (b) The ratio of the compressible to the incompressible surviving fraction for uniform plates and for inserts over 15 % and 30 % of the chord, and the ratio of the rigid loads (dash-dot); the upper axis gives .
The rigid load. Compressibility raises the rigid load by 12 % at and by 25 % at , and then collapses it, to 0.61 of its incompressible value at and 0.26 at (panel b, dash-dot): the low-Mach counterpart of the behaviour of § 6.2, and the regime of the high-frequency theory of Amiet [1].
A uniformly permeable plate. Its load is set by the material, as in § 6.2, and the seepage limit (25) contains no : the compressible and incompressible loads agree to 3 % over the whole range at and to 1 % at . The surviving fraction therefore inherits the non-compactness of the rigid reference entirely. The compressible fraction is 0.88–0.89 times the incompressible one at and 0.78 times it at , and then 1.6, 3.0 and 3.7 times it at , 60 and 120, for both permeabilities.
A leading-edge insert. Here the porous load is itself non-compact. The leading edge, the junction and the rigid aft section carry loads that act on one another with the retarded phase , and over – the lift of the insert departs from its incompressible value by factors between and for , and between and for , whose load nearly cancels near . The surviving fraction follows neither the incompressible curve nor the rigid reference. For the 30% insert it is 0.71 of the incompressible value at and 1.8–3.0 times it over –; for the 15% insert it is 1.3–2.1 times it over –, and 0.28 of it at the near-cancellation.
Non-compactness therefore makes compressibility a low-speed effect as well. At the surviving fraction departs from the incompressible prediction by more than 10% from –, that is –, and by factors of 1.3 to 3.8 over – in every configuration computed. An incompressible porous theory describes the loading only where , whatever the speed.
The porous Theodorsen function
For heave the physical upwash is the constant of (6), and the rigid incompressible response is Theodorsen’s , which the solver returns to (Table 2). The porous responses are shown in Figure 11. As in § 6.2, the surface is a resistive layer, with real and independent of frequency. For an inertive perforate vanishes at high frequency, the surface then behaves as a rigid one, and the high-frequency end of these curves is not reached (§ 6.8).
Figure 11. Heave response of a permeable plate, independent of frequency; solid , dashed . (a) referred to the incompressible quasi-steady lift of the rigid plate; the rigid incompressible curve follows at high frequency, the rigid compressible one saturates at the piston value, and the permeable ones tend to the high-frequency limit of (26), which at is the seepage limit , marked by the short bars (solid , broken ). (b) The surviving fraction : porosity acts as a low-pass filter on the load. (c) The two ends of the frequency range against : the quasi-steady ratio is the steady closed form , while at the surviving fraction is one to two orders of magnitude smaller at , and only 14–27 % smaller at , where compressibility has already capped the rigid response.
Porosity removes the apparent mass almost entirely. The rigid response grows without bound, , because accelerating a rigid plate accelerates the fluid attached to it. A permeable plate cannot sustain the pressure jump that would require: the seepage term grows with the loading, and the response tends to a constant instead. At and the rigid value is 25.0 and the porous ones are 0.630, 0.212 and 0.0795 for , 3 and 8: fractions of , and . The constants are the seepage limit ((25)), , 0.212 and 0.0796, to within 1%; at high frequency the load of a resistive plate is set by the material, which has no inertia to add, and not by the fluid that a rigid plate would have to accelerate. A layer with inertia keeps part of its
Indicial responses
apparent mass (§ 6.8). At the other end of the frequency range the quasi-steady limit is the steady closed form ((27)), and the solver returns it to four figures: at , 0.5000, 0.2048 and 0.0792 against , 0.2048 and 0.0792; at the ratio to the rigid plate at the same Mach number is the same closed form evaluated with , to the same accuracy. Between those two ends lies the whole content of panel (c): for a resistive layer in incompressible flow porosity is far more effective against the non-circulatory load than against the circulatory one: at the apparent mass falls to 0.3 % of its rigid value while the circulation keeps 20 %. For flutter this is the useful direction, since apparent mass is what couples plunge to pitch inertia, and it is the opposite of what the steady lift ratio alone would suggest.
Compressibility caps the rigid response and moves the permeable one much less. At the rigid heave response no longer grows like : it saturates at the acoustic (piston) value of § 2.4, the classical result that at high reduced frequency each element of the surface radiates as a piston. The permeable responses tend to the high-frequency limit ((26)) instead (panel a): at they are 0.42, 0.18 and 0.075 for , 3 and 8, equal to to four figures, against 0.630, 0.212 and 0.0795 at . The change, , is 33, 14 and 6 %, and it is smaller the more permeable the surface, as in § 6.2. The apparent mass that porosity would have removed has therefore already been removed by compressibility, and the surviving fractions at rise to 0.33, 0.14 and 0.059, thirteen to nineteen times the incompressible fractions, so that the benefit is an order of magnitude smaller than the incompressible calculation reports. This is the Sears result of § 6.2 again: a nearly Mach-independent permeable load measured against a rigid load that carries the whole of the classical compressibility effect.
Indicial responses
Figure 12 gives the porous analogues of the Wagner and Küssner functions, obtained from (24) as appendix F describes. Each is normalised by its own quasi-steady value, so the curves show how fast the load settles, not how large it is; the size is the steady factor of (27), and the two statements should be read together.
Figure 12. Indicial responses, each normalised by its own quasi-steady value. (a) The Wagner analogue: the response to a step in incidence, with the apparent-mass impulse removed as appendix § 18 describes. (b) The Küssner analogue: the response to a sharp-edged gust, with measured from the instant the gust front reaches the leading edge. Solid , dashed ; symbols, Jones’s approximations to the classical rigid functions at .
The rigid limit. At and the computed Wagner function agrees with Jones’s classical approximation to 0.007 over , including the correct initial value , which is not imposed anywhere and emerges from the high-frequency limit of the computed transfer function. The Küssner analogue agrees to 0.035 for and departs by up to 0.095 below , where Jones’s two-exponential fit is itself least reliable.
Porosity shortens the transient as well as reducing the load. A permeable plate reaches 90 % of its steady gust response in semichords at and 3.5 at , against 14.3 for a rigid plate: the treatment removes most of the wake memory along with most of the load. The mechanism is the same one that sets : less circulation is shed, so the wake exerts less influence on what follows. The consequence is that a permeable section responds to a passing vortex with a load that is both smaller and shorter, which is not what a quasi-steady estimate scaled by would give.
Compressibility slows the response and changes how it starts. At the rigid Wagner analogue begins near the piston value, since the first instant after a step in incidence is the high-frequency limit of § 6.4; the computation gives 1.08 of the steady lift, against 1.10 in the limit. It then falls within two semichords to 0.58 and recovers more slowly than the incompressible function, reaching 90 % of its steady value at rather than 13. The Küssner analogue is delayed: it has reached 0.10 of its steady value at , against 0.22 incompressibly, and 90 % at against 14.3, because the gust front takes a finite time to make itself felt through a non-compact chord. The permeable cases inherit the delay in weaker form: at the Küssner rise time lengthens from 3.5 to 3.9 semichords. They do not inherit the raised start. A permeable plate has almost no apparent mass even at , so its Wagner analogue already begins near its steady value, and compressibility lowers that start, to 0.88 at , because the piston-limited high-frequency response is then below the permeable steady lift. For a gust-encounter or blade–vortex interaction calculation the practical consequence is that the transient a permeable section produces at flight Mach number is neither the incompressible porous one nor the compressible rigid one.
The steady limit: lift and seepage drag
At the same boundary condition is a complete steady thin-aerofoil theory, and it closes in terms of the single exponent (9). For a uniformly porous plate at incidence the Riemann–Hilbert solution is a single power law and (appendix § 17)
Equation (28) is written for a flat plate at incidence, where the physical upwash is the constant and . For a general mean line the streamwise force is the loading worked against that upwash, which in the normalisation of appendix § 17, where , is
of which (5.4) is the constant- case. The distinction matters wherever camber is used to buy the penalty back: a cambered section at its zero-lift incidence carries loading that integrates to zero but is not zero pointwise, and since the dissipation is quadratic in the loading, the cancellation that removes the lift leaves the drag untouched. Seepage drag vanishes with zero loading, not with zero lift.
Three statements follow, and all three are consequences of the edge exponent rather than of the material as such. First, the lift ratio is exactly twice the edge exponent, so one number sets the loss of lift and the weakening of the singularity together (Figure 13): half the lift is gone at , where . Second, a rigid plate at incidence carries a streamwise pressure-force component that is cancelled exactly by leading-edge suction, and that suction exists only because the loading is singular as ; a permeable edge carries with , so at the nose, there is no suction, and (28) says the streamwise component is dissipated entirely by seepage, at times the suction that the corresponding rigid edge would have developed. Third, the drag integrand behaves as , integrable if and only if , so the porosity-dependent exponent is what keeps the energy budget finite. The drag therefore falls as increases (Figure 13b): the seepage velocity grows, but the pressure jump that drives it falls faster, and the largest penalty, close to the full suction , is paid by a slightly permeable edge.
Figure 13. The steady limit, uniformly permeable plate. (a) The lift ratio: the closed form of (27) (line) against the collocation solver (symbols), over four decades of , from 0.02 to 200. (b) The seepage drag per unit incidence squared, from (28); the dotted line is the leading-edge suction that a rigid edge would have recovered. Solver and closed forms agree to .
Mach number. In compressible flow , and (27) holds with the local value of . When the compressible and incompressible theories are compared at the same flow speed and material, by (14) for any material, and the lift therefore varies with Mach number as
which is the Prandtl–Glauert factor for a rigid plate and tends to unity as , where . In that limit the Prandtl–Glauert rise of the circulation is cancelled exactly by the rise of , and the lift is the seepage load (25) of a surface that passes the incidence upwash. At the steady lift rises by 10.6, 1.7 and 0.25 % for , 3 and 8, against 40 % for a rigid plate, and the unsteady solver reproduces (30) to three figures in its quasi-steady limit. For a resistive layer the limit is the Darcy drop , which contains no Mach number.
For a permeable insert of length at the leading edge the solver returns something simpler than the local analysis would suggest (Figure 14). Over –1 and –10 the computed lift satisfies
Figure 14. Steady penalty of a leading-edge insert. (a) Lift against treated length: symbols, the collocation solver with junction modes; lines, the linear law (31). (b) Seepage drag against lift, both per unit incidence; the identity is the dotted diagonal.
to . It is a linear interpolation between the rigid plate and the uniformly permeable closed form (27), with no dependence on where between the two the junction sits beyond its position. The lift penalty is therefore proportional to the treated chord fraction, which is the design statement one would want and is not obvious from a loading distribution that carries two algebraic singularities. The law is exact: for a constant upwash the steady Riemann–Hilbert problem with a piecewise-constant has a closed-form solution whose lift is linear in the junction position (appendix E), and the solver reproduces it to .
The seepage-drag identity survives the junction. With the forcing normalised to unit incidence, becomes the statement that the two computed coefficients are equal, and they are: to four figures for a uniform plate, and to within 7 % for a partial insert, the largest departures being for short inserts at , where the drag integrand is sampled right up to the junction singularity and converges most slowly.
A layer with inertia
A real perforate or porous layer has inertia as well as resistance, since the fluid in the pores must be accelerated, and the material law of Baddoo et al. [4] carries an effective density for that reason. Writing in (14) gives
resistive below and inertive above it, where falls as . Figure 15 shows the gust response for and : the resistive layer of §5.2 below , and above it a surface whose effective permeability falls to at and at .
Figure 15. Gust response of a resistive–inertive layer, with and , against the resistive layer with and the rigid plate. (a) The Mach factor of each surface at (solid) and (dashed). (b) The fraction of the rigid load at the same Mach number that survives, for the resistive–inertive layer at , and ; dotted, the resistive layer at .
Permeability still controls the sensitivity to compressibility. The Mach factor of panel (a) follows the resistive layer where the two have the same , lying between 0.96 and 1.01 at for , and moves towards the rigid plate as falls: at it is 0.83 at and 0.65 at the top of the range, against 0.86–0.90 for the resistive layer and 0.2–0.4 for a rigid plate. The same statement covers both materials: the sensitivity of the load to compressibility is set by how permeable the surface is at the frequency in question. It also defeats the shortcut of § 6.2: at and the incompressible load of this layer is 1.5 times the compressible one, because the surface has become weakly permeable where the chord is non-compact.
Inertia removes most of the high-frequency benefit. Incompressibly the fraction of the rigid gust load that survives levels off at 0.27–0.31 for , where the resistive layer falls to 0.05 (panel b). At and 0.7 it rises to between 0.4 and 1.0, 1.5 to 3.3 times the incompressible value, and near the interference minima of the rigid response the treatment achieves nothing. The heave response makes the same point: at this layer keeps 17 % of the rigid plate’s apparent mass at –50, against 0.85 % at for the resistive layer with , because its admittance falls with frequency and the high-frequency load is again supported by the flow. At it keeps 82–96 % of the rigid piston load over the same range, against 14 % for the resistive layer. The removal of apparent mass found in § 6.4 is a property of resistive layers.
Limits of validity
The results of §§§ 6.2–§ 6.7 are for resistive layers, and § 6.8 shows how inertia changes them; the formulation itself admits any admittance, complex and varying along the chord. The formulation is linear, subsonic and thin-aerofoil, so it inherits the limits of the Prandtl–Glauert transformation and the Possio kernel: a thin section, attached flow, small incidence, and no transonic region, which in practice means . Nothing in the edge analysis degrades as rises, since the exponents are independent of , and the solver remains cheap there: at and , so , the lift is converged to six figures at . Two further conditions belong to the material rather than to the aerodynamics. The homogenised admittance requires many apertures per hydrodynamic wavelength, which is a statement about the perforate pitch and the frequency, and becomes demanding at the reduced frequencies of § 6.3, where puts the hydrodynamic wavelength at ; and for a bulk medium the pore Reynolds number must be of order unity or below, since the leading correction to Darcy’s law is Forchheimer’s [11], in which the resistance grows with the seepage velocity and hence with the gust amplitude, an amplitude dependence that a linear frequency-domain theory cannot carry. The seepage limit (25) makes that condition more pressing rather than less: a surface that passes the imposed upwash carries seepage velocities of the order of the gust velocity itself.
Conclusions
A linear theory has been developed for the unsteady loading of finite-chord porous aerofoils in compressible subsonic flow. It combines Possio’s integral operator, written with its Cauchy singularity separated from a bounded remainder, with a convective permeable boundary condition, allows chordwise-varying admittance, and retains the shed wake and the unsteady Kutta condition; the material enters through the permeability parameter alone. Because the non-Cauchy part of the operator is bounded, the loading exponents at the aerofoil edges and at admittance discontinuities retain their incompressible functional form when expressed in terms of the local permeability parameter, and are independent of the reduced frequency. The weighted-Jacobi collocation method therefore carries over, with the trailing-edge exponent carried as a parameter and junction modes added where the admittance jumps. The solution reproduces the published incompressible code of Baddoo et al. [4] to 0.09 % and agrees with an independent compressible formulation in physical variables to or better.
The harmonic gust and heave responses, together with their indicial counterparts, show that permeability controls the sensitivity of the unsteady loading to compressibility. The results are for resistive layers, compared at the same flow speed, frequency and material, so that for any material. The pressure jump across a permeable surface is set partly by the surrounding flow and partly by the material impedance, and compressibility acts on the first. As permeability increases the material governs an increasing share of the load, and the Mach-number dependence associated with the surrounding flow weakens: at and the gust load is 0.43 of its incompressible value for a rigid plate, 0.53 at , 0.66 at , 0.86 at and 0.95 at . The weakening is gradual rather than complete: a weakly permeable surface keeps much of the Mach dependence of a rigid plate, and only a strongly permeable one loses it. The Mach number reaches the load through two channels that act in opposite directions. The boundary condition, through which a given material appears more permeable by , lowers the load by a fifth to a quarter at , nearly independently of frequency; the integral operator, which carries the Prandtl–Glauert rise, raises it at low frequency and, unlike its effect on a rigid plate, does not collapse it at high frequency. In the time domain a permeable section responds faster as well as more weakly, reaching 90 % of its steady gust response in 3.5 semichords at against 14.3 for a rigid one, and compressibility lengthens these rise times to 3.9 and 19.4 semichords at .
Closed-form steady and high-frequency limits describe this transition for resistive surfaces. In steady flow the lift varies with Mach number as (30), between the Prandtl–Glauert factor of a rigid plate and unity, and tends to as permeability increases, with a residual Mach dependence of second order in . At high frequency the heave load tends to of the incompressible rigid quasi-steady lift: the material and acoustic (piston) resistances of the two faces act in parallel, since both are driven by the same pressure jump, giving the piston value for a rigid plate and the pressure drop set by the material impedance, , for a strongly permeable one, with a residual Mach dependence of first order in . Together the two limits state when compressibility can be ignored for the porous load: only when . The same limit explains why, for a resistive layer in incompressible flow, porosity removes the apparent mass far more effectively than the circulation: the high-frequency load is set by a material that has no inertia to add. A layer with inertia as well as resistance becomes less permeable as the frequency rises; its Mach sensitivity then moves towards that of a rigid plate, it keeps part of its apparent mass, 17% in the case computed, and it loses most of its high-frequency benefit.
Although the porous load becomes less sensitive to Mach number, its ratio to the impermeable load remains strongly affected by compressibility, because the impermeable load follows the classical behaviour: a Prandtl–Glauert rise at low frequency and a collapse once the chord is acoustically non-compact, to a quarter of its incompressible value at and . Incompressible theory overestimates the ratio at low frequency, most of all in steady flow, where the compressible ratio is the incompressible one times , 0.87 at and 0.73 at for ; it underestimates the ratio once the chord is non-compact. For the gust cases examined at – and – it underestimates the ratio by factors of 1.4–4.3 (7.6 % against 21.6 % at and ), thereby overstating the load reduction achieved by the treatment; for the layer with inertia the factor reaches 3.3, and near the interference minima of the rigid response the treatment achieves nothing. The heave response shows the same structure: the unbounded apparent mass of a rigid plate is capped by compressibility at its piston value, and the fraction of the rigid high-frequency load that a permeable plate retains at rises from under 1 % incompressibly to 14 % at .
It follows that the existing theories cannot simply be combined. Taking the porous load from incompressible theory and the rigid load from compressible theory overestimates the surviving fraction, over – at , by factors of up to 1.96 at and 1.52 at ; correcting the permeability parameter by overcorrects a strongly permeable surface, underestimating its surviving fraction by up to 35 % at ; and for the layer with inertia, whose permeability falls with frequency, the shortcut is 1.5 times too high at . The high-frequency limit sets the condition for the shortcut, for 10 % accuracy, and even where that holds a ratio of lift magnitudes supplies neither the phase, nor the chordwise loading and the Mach-dependent edge exponent on which scattering depends, nor the indicial responses. A theory that carries permeability and compressibility together is therefore required for the load of a weakly or moderately permeable aerofoil, and for everything beyond the lift magnitude at any permeability.
Nor is compressibility only a high-speed effect. The kernel carries the acoustic compactness separately from the Mach number of the boundary condition, and at the surviving fraction departs from its incompressible value by more than 10 % from , and by factors of up to 3.8 at , where the chord spans about two acoustic wavelengths. For a uniformly permeable plate this comes from the rigid reference alone; for a leading-edge insert the porous load is itself non-compact, the leading edge, the junction and the aft section acting on one another with a retarded phase. An incompressible porous theory therefore describes the loading only where , at any speed.
In the steady limit the lift ratio is and the seepage drag is , so the loss of lift and the weakening of the edge singularity are one number, and a permeable edge develops no leading-edge suction. For a leading-edge insert the lift penalty is, to , linear in the treated fraction of the chord, .
The formulation is thus a unified linear theory of the unsteady loading of a thin aerofoil, rigid or permeable, in incompressible or subsonic compressible flow, with the classical and incompressible porous results as its limits. It provides these loads at the cost of a rigid thin-aerofoil calculation, for assessing porous aerofoils and for supplying aerodynamic inputs to aeroelastic and aeroacoustic models.
Acknowledgements
The author used Claude (Anthropic), a large language model, in the versions Claude Opus 5, Claude Opus 5.5 and Claude Fable 5.1, accessed through the Claude desktop application, in the course of this work in September 2026. It was used to check the analytical derivations, including the signs and conventions of the governing equations, to write and run, under the author’s direction, the numerical scripts from which the results and figures were produced, to port and run the published code of Baddoo et al. [4] for the comparison of § 4, to check the bibliography against publisher records, and to assist in drafting and editing the text. Every derivation, numerical result and statement in the paper was examined and verified by the author, who takes full responsibility for its content. The model is not an author of this work.
Funding
This research received no specific grant from any funding agency, commercial or not-for-profit sectors.
Declaration of interests
The author reports no conflict of interest.
Data availability statement
The data and scripts that support the findings of this study are available from the corresponding author upon reasonable request.
Author ORCID
S. Lee, https://orcid.org/0000-0001-8081-2268.
The convective permeable boundary condition
Let be the disturbance velocity potential and the jump across the sheet. Three ingredients are combined. (i) Linearised momentum across the sheet gives . (ii) Mass conservation requires the total normal velocity to be continuous and equal to the seepage, on both faces. (iii) The material law (2), . Eliminating between (i) and (iii) and substituting into (ii) gives (3). The order matters: (ii) is the only ingredient carrying boundary information, and the seepage enters as the normal velocity, not as a second statement about .
To obtain the coefficient of in (5), write for whatever constant the normalisation of implies, the exponential being the Prandtl–Glauert factor of appendix § 14. Then (iii) contributes to the physical normal velocity, and so to the transformed one, which appears with a positive sign on the left of (5), while the flat-plate inversion of (ii) contributes after the Prandtl–Glauert transformation. Fixing the Cauchy coefficient at requires , whence as claimed. Because is the ratio of the seepage coefficient to the Cauchy coefficient it is independent of how is normalised. Holding fixed as , in which case diverges, keeps finite. The resulting condition still contains the convective derivative, which the linearised Bernoulli relation carries in incompressible flow as well; the static porous half-plane condition of Jaworski and Peake [22] and Ayton et al. [3], , is recovered only when that derivative is dropped, as at .
From the convected wave equation to (2.5)
The operator that follows is classical: it is the subsonic unsteady kernel of Possio [34], and no novelty is claimed for it. It is set down here in a particular form, with the Cauchy singularity separated from a remainder that is shown to be bounded, because that separation is what the edge analysis of § 2.5 and the quadrature of § 3.3 both act on, and the classical representations, which carry the singularity inside the special functions, do not supply it.
Prandtl–Glauert. The disturbance potential satisfies , which for is . Writing , the coefficient of vanishes for , leaving . The stretch then gives the Helmholtz equation
on a plate of half-length . Normalising gives as in (1); the same bookkeeping on the gust, whose chordwise wavenumber becomes , gives and hence . Since , is also the physical chordwise coordinate, and : the two potentials are related by . The material derivative transforms as
because . This is why the transformed loading (19) carries rather than , and why the physical pressure jump is and a physical upwash enters (5) multiplied by (§ 2.4).
The dipole sheet. With the potential jump and the bound vorticity, the loaded plate is a sheet of normal doublets with potential , which jumps by across the sheet, and the normal velocity it induces on itself is , with the outgoing Green’s function of (B.1). That integral is hypersingular as written; (B.1) itself removes the difficulty, since away from the source, so that . Integrating the first part by parts once, with the boundary terms vanishing because by Kelvin’s theorem (22) and the sheet continues into the wake at , and using ,
plus the wake integral. The second term carries and has no incompressible counterpart.
The singular part. Since , the first kernel tends to as : the classical Glauert kernel, coefficient and all. Splitting , in which the bracket is bounded, turns (B.2) into a Cauchy principal value plus bounded terms.
Assembly. Adding the seepage contribution (appendix A) and changing the unknown to through gives (5). The change of dependent variable contributes one further term. On the wake , so that there, and the term is , taken over the chord and the wake together. Over the chord alone it would not be bounded: is not zero, and the end point contributes a logarithm, , as . The wake integral contributes the same logarithm with the opposite sign, because is continuous across the trailing edge, , and the two cancel. Over the function is Hölder-continuous, vanishes at the leading edge and is continuous at , so the term is bounded on the whole chord, trailing edge included. The Hankel terms acting on the wake are bounded for the same reason. Hence , which includes the wake through the circulation, is a bounded operator, made up of the regularised acting on , the acting on and the Hilbert transform of over the chord and the wake, and the dominant singular part of (5) is -independent, which is why the exponents of § 2.5 are the same at every Mach number. Setting removes both Hankel terms and leaves the incompressible equation of Baddoo et al. [4].
The trailing-edge exponent in the basis
The basis (17) carries the trailing-edge exponent of (10) as a parameter, so that a porous trailing edge is represented exactly rather than through a rigid-edge weight. Three points are worth recording.
First, the wake mode carries no factor and is therefore unchanged by ; the tie follows from continuity of the wake and not from the edge exponent, so (21) holds for every .
Second, the closed-form antiderivatives generalise with the Jacobi parameter: the whole-chord integrals are with the beta function, and the orthogonality for that the solver relies on is preserved. These have been checked against direct quadrature to – for real and complex .
Third, the generalisation is exact at : the implementation carrying general reproduces the rigid-trailing-edge implementation bit for bit, with zero difference in lift, circulation, loading distribution and every expansion coefficient, over eleven cases spanning rigid plates, porous nose inserts with junctions, complex , up to 4.4, up to 101, and heave forcing.
How much does matter? Less than one would expect for integrated quantities, and a great deal for local ones. On the profiles of Figure 5, where , carrying the correct exponent changes the lift by at most ; on a uniformly permeable plate at , where against the rigid , the lift agrees to five figures. The loading itself does not: within of the trailing edge the two bases differ by a factor of order five, in the direction (10) requires. The reason integrated quantities are insensitive is that the region in which the two exponents differ materially is that small. Local quantities are a different matter, and the loading near a permeable trailing edge is exactly what a trailing-edge scattering calculation needs; that is why the exponent is carried as a parameter rather than fixed.
Quadrature and the aliasing condition
Each influence integral is evaluated on Gauss–Legendre panels graded geometrically towards the singular points and , with the Cauchy singularity removed by the subtraction (23). Grading alone is insufficient: the basis members oscillate as , so a panel wider than one half-period aliases, and the resulting error is systematic rather than random. Requiring every panel to satisfy removes it, and the junction-invariance test of Table 2 falls from to when the condition is imposed. The grading depth is capped so that panel edges never fall below floating-point resolution.
Steady closed forms
At the dominant equation is on , with bounded loading at the trailing edge. Seeking , which for a uniformly porous plate carries at the trailing edge (the bounded-loading condition in that case, consistent with (10) at ), and using the Tricomi identity Tricomi [37]
reduces the equation to the algebraic pair and : the -dependent terms cancel identically only at that , which is (9), and the constant terms then fix . Integrating with gives , so that and hence (27). The seepage dissipation is , which is positive and by the same identity equals , that is, times the leading-edge suction of the corresponding rigid plate, not equal to it, because a permeable edge with develops no suction.
The insert law (31). Let the leading-edge insert occupy with a constant and exponent , the rest of the chord being rigid. Writing , the Plemelj formulae turn the steady equation into on the chord, that is with of (8). For a constant upwash this has the constant particular solution , whatever is, because . The canonical function
has on the insert, on the rigid part, no jump off the chord, the edge behaviour , and of (9), (11) and the Kutta condition, and at infinity since its exponents sum to zero. Hence solves the problem and vanishes at infinity; it is the only such solution, since the difference of two solutions divided by is entire and vanishes at infinity. As , and with , which is linear in . Therefore
which is (31): the rigid plate at , (27) at , and exactly linear between. The argument extends to any number of piecewise-constant segments, the lift remaining linear in each junction position; it relies on the upwash being constant and does not carry over to a cambered section.
Inversion to the time domain
What is inverted is the lift transfer function with its apparent-mass part removed. For heave that part is an impulse at and is not what Wagner’s function describes: writing the computed response as at the top of the sweep, the fitted is subtracted, . The fit returns for a rigid plate, against the exact , and for every permeable case computed. A permeable plate has almost no apparent mass (§ 6.4), so for those cases the subtraction is immaterial. At it returns even for a rigid plate, whose apparent mass compressibility has already removed. For the gust no subtraction is needed, and the leading-edge phase reference of (6) is the one Küssner’s function requires. At finite Mach number both transfer functions are formed from the physical lift (7); the transformed integral of would shift the gust reference by the constant phase and misstate the heave response.
The inversion (24) is then split at the top of the computed range, :
the tail being exact for a transfer function that has settled to a constant. is computed on 102 points, of which 48 are geometrically spaced from to 0.5, 40 are uniformly spaced up to 8 and 14 are geometrically spaced up to 25. It is splined onto a grid fine enough to carry at least twenty points per half-period of before integration; without that refinement the long-time values are aliased. Three convergence checks were made: lowering from to changes by 0.02 and by less than 0.006; raising from 25 to 50, for the rigid and Wagner and Küssner analogues at and 0.5, changes by less than for in every case and by at most 0.014 below , the largest change being in the rigid Wagner analogue at , whose initial piston value is approached only as grows; and the rigid Wagner function is reproduced to 0.007 over , which is the end-to-end test of the scheme.
An independent solution in physical variables
The check of § 4 solves the same physical problem by a route that shares no variable, basis or closure with § 3. With and , a pressure jump carried on the chord alone induces the normal velocity
which follows from the convected wave equation for a potential odd in . The branch of has and is on the radiating interval, and the , which is causality, makes the pole at contribute times its residue; on the real axis the rest is a principal value, evaluated with a Gauss rule symmetric about the pole. No wake appears, because the pressure is continuous across it, and the Kutta condition is imposed by the basis. The trial functions are with the exponents of § 2.5, their Fourier transforms computed by Gauss–Jacobi quadrature (for a rigid plate, , they are Bessel functions in closed form, and both versions were run); the test functions are , . The permeable condition adds to the normal velocity, which is the seepage of (2) rewritten with (4); the sign differs from (2) because is here lower minus upper. The imposed velocity is the physical upwash, the lift is , and nothing is transformed at either end. The -integral is truncated at –6000; for a rigid plate the integrand decays only as and the truncation limits the accuracy to about (the method reproduces the Sears and Theodorsen functions at to that level), while for a permeable plate the weaker edge singularity makes it decay faster and the two solutions agree to .
References
- [1]R. K. Amiet. High frequency thin-airfoil theory for subsonic flow. AIAA J., 14(8):1076–1082, 1976. doi: 10.2514/3.7187.DOI
- [2]L. J. Ayton. Acoustic scattering by a finite rigid plate with a poroelastic extension. J. Fluid Mech., 791:414–438, 2016. doi: 10.1017/jfm.2016.59.DOI
- [3]L. J. Ayton, M. J. Colbrook, T. F. Geyer, P. Chaitanya, and E. Sarradj. Reducing aerofoil–turbulence interaction noise through chordwise-varying porosity. J. Fluid Mech., 906:A1, 2021. doi: 10.1017/jfm.2020.746.DOI
- [4]P. J. Baddoo, R. Hajian, and J. W. Jaworski. Unsteady aerodynamics of porous aerofoils. J. Fluid Mech., 913:A16, 2021. doi: 10.1017/jfm.2020.1031.DOI
- [5]G. K. Batchelor. The Theory of Homogeneous Turbulence. Cambridge University Press, 1953.
- [6]R. L. Bisplinghoff, H. Ashley, and R. L. Halfman. Aeroelasticity. Addison-Wesley, 1955.
- [7]L. Bowen, A. Celik, B. Zhou, M. F. Westin, and M. Azarpeyvand. The effect of leading edge porosity on airfoil turbulence interaction noise. J. Acoust. Soc. Am., 152(3):1437–1448, 2022. doi: 10.1121/10.0013703.DOI
- [8]P. Chaitanya, P. Joseph, S. Narayanan, C. Vanderwel, J. Turner, J. W. Kim, and B. Ganapathisubramani. Performance and mechanism of sinusoidal leading edge serrations for the reduction of turbulence–aerofoil interaction noise. J. Fluid Mech., 818:435–464, 2017. doi: 10.1017/jfm.2017.141.DOI
- [9]P. Chaitanya, P. Joseph, and L. J. Ayton. Leading-edge profiles for the reduction of airfoil interaction noise. AIAA J., 58(3):1118–1129, 2020. doi: 10.2514/1.J058456.DOI
- [10]J. E. Efowcs Williams and L. H. Hall. Aerodynamic sound generation by turbulent flow in the vicinity of a scattering half plane. J. Fluid Mech., 40(4):657–670, 1970. doi: 10.1017/S0022112070000368.DOI
- [11]P. Forchheimer. Wasserbewegung durch Boden. Z. Ver. Dtsch. Ing., 45:1782–1788, 1901.
- [12]F. D. Gakhov. Boundary Value Problems. Pergamon, 1966.
- [13]T. Geyer, E. Sarradj, and C. Fritzsche. Porous airfoils: noise reduction and boundary layer effects. Intl J. Aeroacoust., 9(6):787–820, 2010. doi: 10.1260/1475-472X.9.6.787.DOI
- [14]H. Gill and S. Lee. Uncertainty quantification of hovering rotor noise due to gust-induced unsteady loading using polynomial chaos expansion. J. Am. Helicopter Soc., 71(3):032001, 2026a. doi: 10.4050/JAHS.71.032001.DOI
- [15]H. Gill and S. Lee. Frequency-domain rotor and propeller tonal noise models: analytical framework and prediction accuracy. AIAA J., 64(7):3820–3839, 2026b. doi: 10.2514/1.J066263.DOI
- [16]S. Glegg and W. Devenport. Aeroacoustics of Low Mach Number Flows. Academic Press, 2017.
- [17]J. M. R. Graham. Similarity rules for thin aerofoils in non-stationary subsonic flows. J. Fluid Mech., 43(4):753–766, 1970. doi: 10.1017/S0022112070002719.DOI
- [18]R. Hajian and J. W. Jaworski. The steady aerodynamics of aerofoils with porosity gradients. Proc. R. Soc. A, 473(2205):20170266, 2017. doi: 10.1098/rspa.2017.0266.DOI
- [19]A. D. G. Hales, L. J. Ayton, A. O. Wills, C. Jiang, C. de Silva, D. Moreau, and C. Doolan. A mathematical model for the interaction of anisotropic turbulence with porous surfaces. J. Fluid Mech., 1001:A16, 2024. doi: 10.1017/jfm.2024.1067.DOI
- [20]M. S. Howe. Acoustics of Fluid–Structure Interactions. Cambridge University Press, 1998. doi: 10.1017/CBO9780511662898.DOI
- [21]M. S. Howe, M. I. Scott, and S. R. Sipcic. The influence of tangential mean flow on the Rayleigh conductivity of an aperture. Proc. R. Soc. Lond. A, 452:2303–2317, 1996. doi: 10.1098/rspa.1996.0123.DOI
- [22]J. W. Jaworski and N. Peake. Aerodynamic noise from a poroelastic edge with implications for the silent flight of owls. J. Fluid Mech., 723:456–479, 2013. doi: 10.1017/jfm.2013.139.DOI
- [23]Z. Jia and S. Lee. Impulsive loading noise of a lift-offset coaxial rotor in high-speed forward flight. AIAA J., 58(2):687–701, 2020. doi: 10.2514/1.J058295.DOI
- [24]N. H. Kemp and G. Homicz. Approximate unsteady thin-airfoil theory for subsonic flow. AIAA J., 14(8):1083–1089, 1976. doi: 10.2514/3.7188.DOI
- [25]J. W. Kim, S. Haeri, and P. F. Joseph. On the reduction of aerofoil–turbulence interaction noise associated with wavy leading edges. J. Fluid Mech., 792:526–552, 2016. doi: 10.1017/jfm.2016.95.DOI
- [26]H. G. Küssner. Zusammenfassender Bericht über den instationären Auftrieb von Flügeln. Luftfahrtforschung, 13:410–424, 1936.
- [27]S. Lee, L. Ayton, F. Bertagnolio, S. Moreau, T. P. Chong, and P. Joseph. Turbulent boundary layer trailing-edge noise: theory, computation, experiment, and application. Prog. Aerosp. Sci., 126:100737, 2021. doi: 10.1016/j.paerosci.2021.100737.DOI
- [28]J. G. Leishman. Validation of approximate indicial aerodynamic functions for two-dimensional subsonic flow. J. Aircraft, 25(10):914–922, 1988. doi: 10.2514/3.45680.DOI
- [29]S. Li and S. Lee. Analytic prediction of rotor broadband noise with serrated trailing edges with applications to urban air mobility aircraft. J. Am. Helicopter Soc., 69(3):032005, 2024. doi: 10.4050/JAHS.69.032005.DOI
- [30]B. Lyu, M. Azarpeyvand, and S. Sinayoko. Prediction of noise from serrated trailing edges. J. Fluid Mech., 793:556–588, 2016. doi: 10.1017/jfm.2016.132.DOI
- [31]S. Moreau. Turbomachinery noise predictions: present and future. Acoustics, 1(1):92–116, 2019. doi: 10.3390/acoustics1010008.DOI
- [32]N. I. Muskhelishvili. Singular Integral Equations. Noordhoff, 1953.
- [33]C. Osborne. Unsteady thin-airfoil theory for subsonic flow. AIAA J., 11(2):205–209, 1973. doi: 10.2514/3.6730.DOI
- [34]C. Possio. L’azione aerodinamica sul profilo oscillante in un fluido comprimibile a velocità iposonora. L’Aerotecnica, 18:441–458, 1938.
- [35]W. R. Sears. Some aspects of non-stationary airfoil theory and its practical application. J. Aeronaut. Sci., 8(3):104–108, 1941. doi: 10.2514/8.10655.DOI
- [36]T. Theodorsen. General theory of aerodynamic instability and the mechanism of flutter. Technical Report 496, NACA, 1935.
- [37]F. G. Tricomi. Integral Equations. Interscience, 1957.
- [38]T. von Kármán and W. R. Sears. Airfoil theory for non-uniform motion. J. Aeronaut. Sci., 5(10):379–390, 1938. doi: 10.2514/8.674.DOI
- [39]H. Wagner. Über die Entstehung des dynamischen Auftriebes von Tragflügeln. Z. Angew. Math. Mech., 5(1):17–35, 1925. doi: 10.1002/zamm.19250050103.DOI






