WorksPhysics and Astronomy
NaCo(PO)PO/NC composite as a negative electrode for sodium-ion batteries
Abstract
In recent years, the mixed phosphates based polyanionic electrode materials have attracted great attention in sodium-ion batteries due to their structural stability during cycling and open framework for ion diffusion. Here, we report the electrochemical performance of NaCo(PO)PO/nitrogen doped carbon (NCPP/NC) composite as a negative electrode (anode) for sodium ion batteries in the working potential range of 0.01–3.0~V. It delivers a reversible discharge capacity of 250~mAhg at 0.5~C current rate, which corresponds to the insertion/extraction of four sodium ions. The rate capability study indicates the reversible mechanism and highly stable capacity (61 mAhg) even at high rate up to 5~C as compared to pristine NCPP. The incorporation of the N doped carbon spheres in the composite is expected to enhance the electronic/ionic conductivity, which plays an important role in improving the performance and stability up to 400 cycles at 1~C rate. Intriguingly, the analysis of cyclic voltammetry data measured at different scan rates confirm the capacitive/diffusive controlled mechanism and the extracted diffusion coefficient is found to be around 10 cms. Our results demonstrate that the NCPP/NC composite is also a potential candidate as anode in sodium-ion batteries due to its three dimensional framework, cost effectiveness, enhanced specific capacity as well as further possibility of improving the stability.
Na4Co3(PO4)2P2O7/NC composite as a negative electrode for sodium-ion batteries
Abstract
Introduction
The expeditious development of environmentally benign renewable energy systems has brought significant advancement in the utilization of the wind and solar resources [1]. However, these are intermittent in nature due to the variability in time, duration and location. Therefore, the essential component is to storage the energy for the reliable dependence to fulfil the requirement of the society. In this respect, lithium-ion batteries (LIBs) have achieved immense success with reference to energy and power density and lent a platform for researchers to play-on across the globe, with the application in the grids, electric vehicles and portable electronic devices [2, 3]. However, the non-uniform abundance and limited availability of the lithium resources [4] obstructs to meet the increasing demand of the modern generation [5]. In order to search cost effective alternative, sodium-ion batteries (SIBs) are emerging as a pragmatic option owing to the large availability, uniform geographical distribution of the sodium resources in the earth’s crust and also the SIBs follows the similar intercalation chemistry as LIBs [6]. However, there are many challenges to develop electrode materials to accommodate the larger size sodium-ion, and the size also plays a crucial role in diffusion through electrolyte during charge/discharge. In comparison to the widely investigated layered [7, 8, 9, 10] as well as polyanionic type materials as cathode [11, 12, 13, 14], search for the appropriate anode materials require immediate attention because the graphite anode cannot accommodate Na ions at low-potential when used with Na salt electrolyte in sodium-ion batteries. Therefore, various carbonaceous materials have been investigated for their electrochemical performance towards SIBs as anode
[15, 16, 17]. However, their performance in terms of stability and storage capability is relegated than that of the corresponding lithium counterparts mainly due to the large radius of sodium. This leads to the reduced diffusion of sodium ions and huge volume change during the intercalation/deintercalation mechanism, hence, resulting in the severe structural degradation of the host material and poor cycleability and rate capability, which are not favorable for the application in the energy storage systems [18]. Hence, major consideration is imperative to find the suitable anode materials with excellent storage capacity and rate capability as well as long cycle life.
In order to achieve excellent electrochemical performance, materials possessing open and stable three-dimensional (3D) frameworks with the larger diffusion pathways and interstitial space are expected to overcome the above challenges found in SIBs [14, 18, 19]. In this context, the polyanionic compounds, owing to their 3D framework, structural and thermal stability are considered potential candidates [14]. For example, the mixed phosphates with general formula (M=Fe, Mn, Co, Ni) have attracted great attention as new class of electrode materials due to the low volume expansion arising from the strongly covalent bonded framework with the excellent cycling performance and longer lifetime of the battery system [20, 21, 22, 23, 24, 25, 26]. These mixed phosphate materials have three dimensional orthorhombic framework containing octahedra and tetrahedra sharing corners with pyrophosphate group via P–O–P interlayer linkage [27]. Interestingly, the sodium ion occupies four sites in the three dimensional (3D) diffusion pathways. In comparison to the ion diffusivity in 1D ion channel, the 3D ion channels have greater advantage due to the availability of the alternative diffusion pathways, which exist even if defects in the bulk hinders the ion mobility in one particular direction of 3D ion channel [22, 23, 24, 25, 26, 27, 28, 29]. More importantly, due to the availability of large 3D channels in the NaCo(PO)PO (NCPP), it can be considered as a good 3D ionic conductor [22, 23, 24, 25, 26, 27, 28, 29]. It also shows low-volume expansion during the cycling and has the high theoretical capacity (170 mAhg). However, the lower energy densities and reversible capacities are observed due to the introduction of the PO groups, leading to the reduced electronic conductivity. In order to enhance the electronic conductivity and reversible capacity, incorporation of carbon matrix in the structure is very effective. Moreover, the dopant heteroatoms (N, B, S, P) can provide pseudo-capacitance, enhance the interlayer distance, as well as generate extrinsic defects to provide more active sites for better Li-/Na-ion storage [30, 31, 32, 33, 34]. In fact, N doping introduces donor states near the Fermi level, which can enhance conductivity and reactivity by making the impurity sites active both electronically and chemically [35, 36]. Therefore, incorporation of N doped carbon matrix in NCPP electrode in the form of composite (NCPP/NC) is expected to increase the conductivity, and help in improving the energy density, rate capacity and cycle life of the Na-ion batteries [32, 33, 34].
As discussed above, recently the NCPP materials have been investigated in the high potential range as cathode [22, 23, 24, 25, 26, 27, 28, 29]; however, to the best of our knowledge, its electrochemical investigation has not been explored so far in the lower working potential as anode in sodium-ion batteries. Therefore, in this paper we report the synthesis of a composite of N-doped carbon and NCPP via a facile sol-gel route and examine its electrochemical performance as a negative electrode (anode) for SIBs and compared with the pristine NCPP material. We demonstrate a significant increase in the storage capacity of 250 mAhg at 0.5 C current rate in the working potential range of 0.01–3.0 V. The N-doped carbon incorporated on NCPP with the formation of a composite through the microsized spherical particles, provides fast electron transfer and provides sufficient bonding sites with high sodium ion diffusion in the range of 10 cms. We found that a well designed NCPP/NC composite as anode shows excellent rate capability (61 mAhg at 5 C rate) and outstanding cycling stability (400 cycles) as compared to the pristine NCPP. Our study demonstrate the superior performance of the composite as anode for high performance sodium-ion rechargeable batteries.
Experimental
Synthesis of N doped carbon spheres: In order to prepare the N doped carbon spheres, we use 0.1 M of sucrose as a carbon precursor and 0.2 M of ammonium sulphate for N doping, which were dissolved in 100 ml of de-ionized water and stirred for 1 h. Afterward, the solution mixture was transferred into the Teflon lined stainless steel hydrothermal reactor and heat treated for 4 h at 200°C. This reaction mixture was filtered and washed with DI water and ethanol followed by overnight drying to obtained hydro-thermal char, which were annealed at
900°C for 3 h in an inert Ar atmosphere, which resulted in the N doped carbon spheres [30, 32, 33].
Synthesis of NCPP/NC nano-composite: Facile sol-gel process was used to synthesize the composites of NCPP/NC. First, the stoichiometric amounts of NaHPO·2HO, Co(NO)·6HO, and CHO·HO were added to de-ionized water in sequence with continuous stirring for 3 h at 120°C. A moderate amount of citric acid was used as a carbon precursor and also as a chelating agent. The formed gel kept for calcination at 300°C for 3 h in air atmosphere. The obtained product was grind into fine powder followed by mixing with 30% of N doped carbon and grind again for 2-3 h by using mortar pestle. Further, an intermediate product was heated to 700°C with 2°C min rate and kept there for 10 h in an Ar atmosphere to obtain the NCPP/NC composites. The pristine NCPP was synthesised for comparison in similar way except incorporation of the NC matrix. The schematic illustration of synthesis procedure of NC matrix and the NCPP/NC composites is shown in Figure 1.
Figure 1. Schematic illustration of synthesis process of the NCPP/NC composite material.
Material characterization: The room temperature powder X-ray diffraction (XRD) measurements were carried out using Cu-Kα radiation (1.5406 Å) in the 2θ range of 5–80° using Rigaku Mini Flex 600 diffractometer. The recorded XRD data were analysed by Rietveld refinement using FullProf package, where we fitted the background using linear interpolation between data points. The surface morphology and the elemental mapping of the as prepared materials have been investigated through the field emission scanning electron microscope (FE-SEM) using the JEOL JSM-7800F Prime system. The high resolution transmission electron microscopy (HRTEM) measurements have been done with Tecnai G2 20 system. The Raman spectra of prepared pellets were recorded with Renishaw invia confocal Raman microscope using 2400 lines/mm grating at wavelength of 532 nm with laser power of 1 mW on the sample.
Coin-cell fabrication: The electrochemical properties of NCPP/NC composites have been examined by two-electrode coin cell configuration. In order to fabricate the anode, the slurry was prepared by mixing the active material with the acetylene black and the binder (polyvinylidenedifluoride, PVDF) in the ratio of 7:2:1 and dissolved in a N-methyl pyrrolodinone (NMP) solvent. The prepared slurry was coated on to Cu foil, which serve as a current collector using film coater and doctor blade. Subsequently, the coated copper sheet is air dried for 12 h and vacuum dried at 110°C overnight in order to completely remove the solvent. The circular disks of 12 mm were cut using a disc cutter and vacuum dried at 100°C for about 5 h. The coin cells of type CR2032 were assembled in an Argon-filled glovebox (UniLab Pro SP from MBraun) having oxygen and water content less than 0.1 ppm. The half cells are assembled using sodium metal foil as a counter electrode, a glass microfiber paper as a separator (Glass Fiber Filter GB 100R) and the electrolyte as 1 M NaClO₄ in diethyl carbonate (DEC)–ethylene carbonate (EC) in 1:1 volume.
Electrochemical measurements: The cyclic voltammetry (CV) measurements were performed using VMP-3 Biologic pontentiostat at different scan rates between 0.01-3.0 V for the anode. The galvanostatic charge-discharge measurements for the cells were carried out by using Neware battery analyser BTS400 as well as VMP-3 Biologic pontentiostat. The electrochemical impedance spectroscopy (EIS) data were collected in the frequency range from 100 kHz to 10 mHz with an AC amplitude of 10 mV using Biologic VMP-3 potentiostat.
Results and discussion
The Rietveld refinement of the XRD patterns of NCPP and NCPP/NC are shown in Figure 2(a, Figure 2c), respectively, which confirm the formation of single phase and mixed phosphates structure of both the samples. The lattice parameters of the NCPP/NC compound obtained are: Å, Å, Å, and a unit volume of 1242.13 Å corresponding to an orthorhombic Pn2₁a space group. The crystal structure of NCPP/NC is displayed in Figure 2(b) using the program VESTA. The NCPP consists of corner/edge-sharing of CoO₆ octahedra and PO₄ tetrahedra where the PO₄ units share one edge and two corners with the adjacent CoO₆ octahedra, forming a pseudo-layered structure along the -plane. These layers are successively bridged by P₂O₇ pyrophosphate units along the −axis to form large 3D ion channels having four types of Na⁺ ion sites (Na1, Na2, Na3, Na4). Further, we use Raman spectroscopy to check the structure, which confirms the presence of graphitized carbon as the spectra are shown in Figure 2(d). For the NCPP/NC sample, the characteristic peaks of D- and G-bands are observed at 1343 and 1588 cm, respectively. Whereas, these peaks are at 1349 and 1595 cm, respectively, for the NCPP sample. These are corresponded to the disordered and graphitized carbons, which could be attributed to N doping in carbon and decomposed carbons [30]. The peaks appear in the range of 300 cm to 1200 cm con-
Figure 2. The Rietveld refined XRD patterns of the (a) NCPP and (c) NCPP/NC samples; (b) the schematic illustration of NCPP crystal structure, where Co, P, Na and O are shown by the purple, green, blue ad red color respectively, visualised in the VESTA software; (d) the Raman spectra of the NCPP and NCPP/NC composite; the SEM images of the (e) N doped carbon spheres, (f) pristine NCPP sample, and (g) NCPP/NC composite; the elemental mapping images of (h-m) Na, Co, P, C, N and O, respectively in the NCPP/NC composite; the TEM images of (n) pristine NCPP, and (q) NCPP/NC composite; the high resolution TEM images of (o) pristine NCPP, and (r) NCPP/NC composite; the SAED patterns of (p) pristine NCPP, and (s) NCPP/NC composite samples.
sistent with the internal modes of PO [37]. The diphosphate ion consists of two PO tetrahedra with a central P-O-P linkage [38]. The Raman shift at 1037 cm corresponds to stretching mode of PO group, peaks appear at 715 and 952 cm correspond to bridging mode of PO. The peak present at 343 cm indicates the deformation of P-O-P bond [38]. The detailed microstructures of the as-synthesized N doped carbon spheres, NCPP and NCPP/NC samples are characterized using FE-SEM and results are displayed in Figure 2(e–Figure 2g), respectively. The spheres like morphology obtained for N doped carbon where as NCPP is composed of flakes and NCPP/NC is consist of flakes of NCPP and microspheres of N doped carbon. The size of the carbon spheres is in the range of 2 to 5 µm. The elemental mapping images confirm the homogeneous distribution of all the elements (Na, Co, P, C, N and O) in the sample, see Figure 2(h–Figure 2m). To further investigate the detailed morphologies and structures of NC and NCPP/NC, we perform HR-TEM measurements, which demonstrate the sheet like structure of the NCPP sample, as shown in the Figure 2(n). In Figure 2(o) we show the high resolution image for the NCPP sample where the extracted interlayer distance was found to be 0.55 nm for (011) reflection and 0.34 for (402) reflection. Figure 2(q) shows the N doped carbon spheres surrounded by the NCPP sheet, and the high magnification image in Figure 2(r) indicates the surface boundary of NCPP and N doped carbon spheres. The selected area electron diffraction (SAED) patterns confirm the polycrystalline nature of both the NCPP and NCPP/NC samples, as shown in Figure 2(p, Figure 2s), respectively.
Now we focus on to investigate the electrochemical performance of both the NCPP and NCPP/NC samples as negative electrode for sodium-ion batteries in the potential range of 0.01–3.0 V. The Cyclic voltametery (CV) measurements were performed vs. Na/Na for first 3 cycles at a scan rate of 0.1 mVs, as shown in Figure 3(a, Figure 3b) for both the NCPP and NCPP/NC electrodes, respectively. The observed sharp cathodic peak at around 0.2 V is mostly due to the decomposition of the electrolyte and the film formation at the solid electrolyte interphase (SEI) in the first scan only as the peak disappears in subsequent cycles [39, 40]. The SEI is of crucial importance to the battery performance as it protects the anode by inhibiting the transfer of electrons from the anode to the electrolyte, while allowing only sodium ion diffusion. Moreover, the reversible peaks appear at in cathode region and in anodic region due to the intercalation and deintercalation of Na ions in carbon matrix [39, 41]. From the second cycle onwards, the reversible peaks appear at around and due to the sodiation/desodiation process along with the electrochemical reduction/oxidation of Co in the active material [42, 43, 44, 45] of NCPP electrodes. Similar redox couples are observed in the CV curves of the pristine NCPP material, which suggests for the same electrochemical reactions. However, when compared to the NCPP/NC composite, the pristine NCPP material shows greater electrode polarization with the large voltage difference between cathodic and anodic peaks. The galvanostatic charge-discharge (GCD) measurements were carried out to find the specific capacity and the cycling stability of the NCPP/NC composite. The GCD profiles measured at C rate in between and voltage for both the NCPP and NCPP/NC anodes are shown in Figure 3(c) and (Figure 3d), respectively. A prolonged voltage plateau appears below for both the electrodes due to the sodiation of NCPP and the formation of SEI layer. The slope in the range of to during the charging represents the reversible oxidation of Co in the active material. The
Figure 3. (a, b) Cyclic voltammetry (CV) curves of the NCPP and NCPP/NC anodes, respectively, measured at 0.1 mVs scan rate, and (c, d) Charge-discharge profiles of the NCPP and NCPP/NC anodes, respectively, measured at 0.5 C current rate.
NCPP delivers the discharge capacity of at second cycle, whereas the NCPP/NC composite exhibits . Interestingly, the NCPP/NC delivers significantly higher reversible capacity because of the the addition of the N doped carbon content in the composite, which improves the electronic conductivity and increases the Na storage capacity. It also act as a buffer to sustain mechanical structure of electrode due to the volumetric expansion during sodiation/desodiation.
In order to understand the kinetics, electrochemical impedance spectroscopy measurements of the NCPP and NCPP/NC electrodes were performed at room temperature in the frequency range of to . As shown in Figure 4(a), the Nyquist plots of the two electrodes consist of a depressed semicircle in the high-frequency region, which is attributed to the SEI film formation, contact resistance, and charge transfer resistance on the electrode/electrolyte interface. In addition, an inclined line in the low-frequency range corresponds to the sodium-diffusion process within the electrodes [46]. We can calculate the ohmic resistance (), SEI contribution () and charge transfer resistance () by fitting the circuit model, as shown in the inset of Figure 4(a), which mimics the reaction mechanism into the electronic components. The resistance is observed to be lower for the NCPP/NC () electrode as compared to the pristine NCPP (), which suggest the more conducting nature and shorten the diffusion path length to facilitate the Na transference between electrode and electrolyte. Also, the contributions from SEI resistance and are found to be around and for NCPP/NC, and and for NCPP, respectively. The reduced resistance values of the NCPP/NC electrode as compared to pristine NCPP are possibly due to N-doped carbon spheres, which decrease the mechanical strain and avoid volume expansion during the charge/discharge process. Additionally, the N doping enhances the electronic conductivity, providing continuous and rapid electron transport, which may accelerate the Na ion storage capacity of the electrode material. In Figure 4(b) we show the comparative specific capacity performance of the NCPP and NCPP/NC electrodes at different current rates ranging from 0.5 to 5 C where 1 C = . Evidently, the rate capability of the NCPP/NC composite is significantly better than that of the pristine NCPP. The NCPP/NC electrode delivers reversible capacity of 250, 173 and 112 at 0.5, 1 and 2 C current rates, respectively. At high current rate of 5 C, it delivers around 61 of discharge capacity and after reverting back to 0.5 C rate, the NCPP/NC electrode recovers around 129 of discharge capacity. The cycling stability of both the NCPP and NCPP/NC electrodes is tested at relatively high current rate of 1 C, as shown in Figure 4(c). Here, we found that there is a fast capacity fading within first 50 cycles and thereafter the NCPP/NC electrode exhibits better cycle life even after 400 cycles where it shows around 44 specific capacity as compared to the 28 for pristine NCPP having 100% Coulombic efficiency, see Figure 4(c). However, the results in Figure 4(b), (Figure 4c) suggest that initial low current rate may play crucial role for cycling stability and require detailed investigation in this context for further understanding to search new anode materials having open framework for sodium-ion batteries [47]. Moreover, the EIS measurements of NCPP/NC electrode were carried out after 50, 100 and 200 charge-discharge cycles and compared in Figure 4(d),
Figure 4. (a) The Nyquist plot, (b) the rate capability, (c) the cyclic stability at 1 C current rate of the NCPP and NCPP/NC anodes, (d) electrochemical impedance spectra of the NCPP/NC anode during cycling at 1 C rate.
where it is clearly visible that the charge transfer resistance along with Warburg resistance increase during the cycling. This is possibly due to small structural disorientation caused by cracks in the active material during cycling (discussed later). These observations are consistent as the specific capacity decays faster with the cycle numbers in Figure 4(c).
Note that the charge storage mechanism associated with any electrode can be interpreted from the kinetic analysis of CV measurements, which elucidate the contribution of surface controlled capacitive process and diffusion controlled redox process in the electrochemical reaction. In order to investigate these details for the NCPP/NC electrode, the cyclic voltametry measurements were performed at different scan rates ranging from 0.1 to 0.3 mV s and the results are shown in Figure 5(a). With increasing the scan rate, the anodic peak ‘A’ does not shift indicating good electrochemical reversibility; whereas, the cathodic peak ‘C’ exhibit a shift towards lower potential convey a small polarization. These CV curves are used to define the relationship between the peak current () with scan rate () by the power law [48], where is an exponent. In Figure 5(b), we plot the as a function of where the slope can be used to calculate the diffusion coefficient [28, 49]. The contribution of capacitive and diffusion process can be calculated by the value of exponent parameter . It has been reported that if , the charge storage mechanism refers to a diffusion-controlled electrochemical process and if , it refers to an ideal capacitive controlled process [48]. Further, we show the linear fit to the log-log plot, see inset of Figure 5(b), to evaluate the values for oxidative and reductive peaks, which are found to be around 0.5 and 0.8, respectively. These values suggest for a combination of both diffusive (anodic regime) and pseudo-capacitive (cathodic regime) controlled Na insertion/de-insertion into the NCPP/NC composite electrode [33, 34, 42, 50].
Figure 5. (a) Cyclic voltammogram (third cycle) of NCPP/NC composite electrode at different scan rates, (b) the plot between peak current () with square root of scan rates for anodic and cathodic peaks for the NCPP/NC composite, inset in (b) shows the linear fit to log-log plot, (c) the extracted capacitive contributed area of 42% at scan rate 0.2 mV s, (d) the contribution of the capacitive and diffusive contributions in percentage at different scan rates for the NCPP/NC composite.
The contributions of diffusive and capacitive processes are calculated using the equation, , where is the total current, and describe the capacitive part and diffusive controlled insertion, respectively. The linear fit to the versus for anodic and cathodic peaks give (slope) and (intercept), which are used to quantify the pseudo-capacitive contribution at different scan rates. Figure 5(c) shows the capacitive contributed area of around 42% at 0.2 mV s. A higher diffusive contribution of 66% is achieved at 0.1 mV s, which decreases at higher scan rates due to more surface-controlled reactions. An increasing trend of capacitive behavior with 34%, 42% and 46% contribution [42, 50] are observed at 0.1, 0.2 and 0.3 mV s scan rates. These results are presented in the percentage ratio versus the scan rate in Figure 5(d), which indicate the pseudo-capacitive effect for the NCPP/NC composite electrode [33, 34, 42, 50]. Further, the Na ion diffusion coefficient of the electrode can be determined from the CV using
the Randles-Sevcik equation [28, 49]:
where, the related parameters is the surface area of the electrode (cm), is the bulk concentration of the Na ions (mol cm), is the number of electrons involved in the redox reaction () 1, is the diffusion coefficient of sodium ions in dip corresponds to the peak current (in mA). Using eq. 1, the calculated diffusion coefficient of Na for both the cathodic (C) and anodic (A) peaks is found to be around cms, which is considered towards higher side for anode materials [10]. In order to examine the electrode kinetics, the EIS measurements were performed, which show the change in resistance at different states during first cycle charge-discharge cycle for the NCPP/NC electrode, see Figure 6(a, Figure 6b). Interestingly, the charge transfer resistance of 40 Ω is observed at OCV (2.0 V). During the discharge from 2.0 to 0.4 V and then to 0.1 V the value is increased to around 55 and 135 Ω, respectively and on completion of the discharge process at 0.01 V the value decreased slight to 125 Ω, see Figure 6(a). It is important to understand that during the discharging process, the Na ion insertion takes place via the infiltration of electrolyte to solid/electrolyte interface and entering to the crystal lattice of the NCPP/NC electrode. This process demands to cross a high kinetics hurdle which increased the value. At discharge up to lower voltage around 0.1 V, the activation of the NCPP/NC electrode with formation of low valance Co species help to improve the electronic conductivity by reducing the charge transfer resistance and on complete discharge it exhibits a certain value of . Further, the value increases during charging process, i.e., 120, 165, 200 at 0.1, 1.9 and 3.0 V, respectively, see Figure 6(b). This is due to the slow
Figure 6. Electrochemical impedance spectra (EIS) of the NCPP/NC composite anode measured at different voltages during (a) discharge process, and (b) charge process.
reaction kinetics of the Na ion transportation at charge plateau voltage of about 1.9 V and the the formation of Co ions on complete charge, which diminish the electronic conductivity of Co–based oxide materials [51, 52].
Finally, the morphological and structural variation in the NCPP/NC electrode have been investigated after 400 cycles of de/sodiation by FE-SEM and XRD measurements. Figure 7(a) represents the schematic illustration of Na insertion and deinsertion into the NCPP/NC electrode. The SEM images for the fresh electrode are shown in Figure 7(b, Figure 7c), where there is no evidence of cracks and pulverization in electrode surface. However, if we see the images taken after 400 cycles shown in Figure 7(d, Figure 7e), it is clearly visible that the flakes and spheres are completely cracked into parts and the smooth surface of the electrode is shattered. The cracks lead to disintegration and isolation of certain area of active material in the post-cycling stage, which may generate strain/internal resistance and consequently result in the capacity fading [43, 53]. This can be attributed to chemo-mechanical degradation of the electrode as the formation of cracks in the active electrode surface area are visible in ex-situ post-cycling morphology analysis in Figure 7(c, Figure 7e). These observations are also consistent with the in-situ EIS measurements presented above in Figure 6. Moreover, we study the structural alteration of the electrode material after 400 continuous charge-discharge cycles at 1 C rate. The collected XRD pattern is displayed in Figure 7(f). Interestingly, the reflections peaks are clearly visible, which indicates the structural stability of NCPP/NC electrode even after going through 400 cycles of sodiation/desodiation process. It is worth noting here that like NASICON structured composite materials [54, 55, 56, 57, 58, 59, 60], our results demonstrate that the mixed polyanionic composite with N doped carbon spares (NCPP/NC) could be a potential candidate as a negative electrode for sodium-ion batteries.
Figure 7. (a) Schematic illustration of Na insertion and deinsertion into the NCPP/NC electrode; the FE-SEM images of the NCPP/NC electrode (b, c) fresh cell and (d, e) after 400 cycles of charge-discharge at 1 C rate, (f) the XRD pattern of the NCPP/NC electrode after 400 cycles of charge-discharge.
Conclusions
In conclusion, we have successfully synthesized the NCPP/NC composite with simple facile and scalable synthetic route (sol-gel method) and examined as negative electrode for sodium-ion batteries. Here, the NCPP sheet is surrounded the surface of N doped carbon micro spheres, which improved the electrical and ionic conductivity and enhanced the sodium storage capacity of the NCPP/NC anode as compared to the pristine NCPP anode. The NCPP/NC anode delivers a reversible discharge capacity of 250 mAhg at 0.5 C current rate corresponds to intercalation and de-intercalation of four sodium ions and found to be stable up to high rate of 5 C (61 mAhg). However, when starting the cell directly at high current rate 1 C, the capacity fading is relatively fast within 50 cycles, but after that the NCPP/NC anode shows slightly better electrochemical performance with stable life up to 400 cycles and appreciable Coulombic efficiency (≈100%). The extracted value of diffusion coefficient is found to be around . We demonstrate that in the composite, the carbon spheres offers intimate contact between the NCPP sheet, hinders the aggregation and alleviates the volume expansion in the NCPP during sodium ion insertion and extraction process. Additionally, the N doping in carbon spheres expedite the kinetics of Na ion transportation over the electrode/electrolyte interface, which boost the rate performance at elevated current rate. Hence, the development of composites could improve the low conductivity problem of polyanionic materials to make them potential candidate for forthcoming sodium-ion battery devices.
Acknowledgement
PKD, SKS and JP thank the DST project (DST/TMD/MECSP/2K17/07), MHRD and UGC, respectively for the fellowship. The Authors acknowledge the financial support from DST through ”DST-IIT Delhi Energy Storage Platform on Batteries” (project no. DST/TMD/MECSP/2K17/07). We thank IIT Delhi for providing research facilities for sample characterization (XRD and Raman spectrometer at the physics department, FE-SEM and HR-TEM at CRF). We acknowledge the financial support from SERB through project under the core research grant (file no.: CRG/2020/003436).
Author Contribution Statement All the authors have contributed to this work including data analysis and manuscript preparation.
Notes The authors declare no competing financial interest.
References
- [1]Gielen, D.; Boshell, F.; Saygin, D.; Bazilian, M. D.; Wagner, N.; Gorini, R. The role of renewable energy in the global energy transformation, Energy Strategy Reviews 2019, 24, 38–50.
- [2]Dunn, B.; Kamath, H.; Tarascon, J. -M. Electrical energy storage for the grid: a battery of choices, Science 2011, 334, 928–935,DOI
- [3]Li, M.; Lu, J.; Chen, Z. W.; Amine, K. 30 years of lithium-ion batteries, Adv. Mater. 2018, 30, 1800561.DOI
- [4]Tarascon, J. -M. Is lithium the new gold?, Nat. Chem. 2010, 2, 510.DOI
- [5]Grosjean, C.; Miranda, P. H.; Perrin, M.; Poggi, P. Assessment of world lithium resources and consequences of their geographic distribution on the expected development of the electric vehicle industry, Renew. Sustain. Energy Rev. 2012, 16, 1735–1744.DOI
- [6]Sawicki, M.; Shaw, L. L. Advances and challenges of sodium ion batteries as post lithium ion batteries. RSC Adv. 2015, 5(65), 53129–53154.DOI
- [7]Yu, H.; Guo, S.; Zhu, Y.; Ishida, M.; Zhou, H. Novel titanium-based O3-type NaTi₀.₅Ni₀.₅O₂ as a cathode material for sodium ion batteries. Chemical Communications, 2014, 50(4), 457–459.
- [8]Chandra, M.; Shukla, R.; Saroha, R.; Panwar, A. K.; Gupta, A.; Basu, S.; Dhaka, R. S. Physical properties and electrochemical performance of Zn-substituted Na₀.₄₄Mn₁−xZnxO₂ nanostructures as cathode in Na-ion batteries, Ceramics International, 2018, 44, 21127–21131.arxiv.org/abs/1808.04267
- [9]Saroha, R.; Khan, T. S.; Chandra, M.; Shukla, R.; Panwar, A. K.; Gupta, A.; Ali Haider, M.; Basu, S.; Dhaka, R. S. Electrochemical properties of Na₀.₆₆V₄O₁₀ nanostructures as cathode material in rechargeable batteries for energy storage applications, ACS Omega, 2019, 4, 9878–9888.DOI
- [10]Chandra, M.; Khan, T. S.; Shukla, R.; Ahmed, S.; Gupta, A.; Basu, S.; Ali Haider, M.; Dhaka, R. S. Diffusion coefficient and electrochemical performance of NaVO₃ anode in Li/Na batteries, Electrochimica Acta 2020, 331C, 135293 (1–10).DOI
- [11]Chihara, K.; Kitajou, A.; Gocheva, I. D.; Okada, S.; Yamaki, J. I. Cathode properties of Na₃M₂(PO₄)₂F₃ [M= Ti, Fe, V] for sodium-ion batteries. Journal of power sources, 2013, 227, 80-85.DOI
- [12]Fang, Y.; Xiao, L.; Qian, J.; Ai, X.; Yang, H.; Cao, Y. Mesoporous amorphous FePO₄ nanospheres as high-performance cathode material for sodium-ion batteries. Nano letters, 2014 14(6), 3539–3543.DOI
- [13]Deng, C.; Zhang, S.; Wu, Y. Hydrothermal-assisted synthesis of the Na₇V₄(P₂O₇)₄(PO₄)/C nanorod and its fast sodium intercalation chemistry in aqueous rechargeable sodium batteries. Nanoscale, 2015, 7(2), 487-491.DOI
- [14]Sapra, S. K.; Pati, J.; Dwivedi, P. K.; Basu, S.; Chang, J.-K.; Dhaka, R. S. A comprehensive review on recent advances of polyanionic cathode materials in Na-ion batteries for cost effective energy storage applications, WIREs Energy and Environment, 2021, http://doi.org/10.1002/wene.400.
- [15]Komaba, S.; Murata, W.; Ishikawa, T.; Yabuuchi, N.; Ozeki, T.; Nakayama, T.; Ogata, A.; Gotoh, K.; Fujiwara, K. Electrochemical Na insertion and solid electrolyte interphase for hard-carbon electrodes and application to Na-ion batteries. Advanced Functional Materials, 2011, 21(20), 3859–3867.DOI
- [16]Xie, F.; Xu, Z.; Guo, Z.; Titirici, M. -M. Hard carbons for sodium-ion batteries and beyond, Prog. Energy 2020, 2, 042002.
- [17]Xiao, B.; Rojo, T.; Li, X. A Minireview on hard carbon as Na-ion battery anodes: progresses and challenges, ChemSusChem, 2021, 10.1002/cssc.201801879
- [18]Saravanan, K.; Mason, C. W.; Rudola, A.; Wong, K. H.; Balaya, P. The first report on excellent cycling stability and superior rate capability of NaV₂(PO₄)₃ for sodium ion batteries. Advanced Energy Materials, 2013 3(4), 444–450.DOI
- [19]Jian, Z.; Han, W.; Lu, X.; Yang, H.; Hu, Y. S.; Zhou, J.; Zhou, Z.; Li, J.; Chen, W.; Chen, D.; Chen, L. Superior electrochemical performance and storage mechanism of Na₃V₂(PO₄)₃ cathode for room-temperature sodium-ion batteries. Advanced Energy Materials, 2013, 3(2), 156– 160.
- [20]Sanz, F.; Parada, C.; Rojo, J. M.; Ruiz-Valero, C. Synthesis, structural characterization, magnetic properties, and ionic conductivity of Na₄M′′₃(PO₄)₂(P₂O₇)(M′′ = Mn, Co, Ni). Chem. Mater. 2001, 13(4), 1334–1340.
- [21]Kang, J.; Park, H.; Kim, H.; Jo, J. H.; Ko, W.; Lee, Y.; Myung, S.-T.; Kim, J. Development of a new mixed-polyanion cathode with superior electrochemical performances for Na-ion batteries, ACS Sustainable Chem. Eng. 2020, 8, 163–171.DOI
- [22]Zarrabeitia, M.; Jàuregui, M.; Sharma, N.; Pramudita, J. C.; Cabanas, M. C. Na₄Co₃(PO₄)₂P₂O₇ through correlative operando x-ray diffraction and electrochemical impedance spectroscopy. Chem. Mater. 2019, 31, 5152–5159.
- [23]Nose, M.; Shiotani, S.; Nakayama, H.; Nobuhara, K.; Nakanishi, S.; Iba, H. Na₄Co₂.₄Mn₀.₃Ni₀.₃(PO₄)₂P₂O₇: high potential and high capacity electrode material for sodium-ion batteries, Electrochemistry Communications 2013, 34, 266–269.DOI
- [24]Nose, M.; Nakayama, H.; Nobuhara, K.; Yamaguchi, H.; Nakanishi, S.; Iba, H. Na₄Co₃(PO₄)₂P₂O₇: A novel storage material for sodium-ion batteries, Journal of Power Sources 2013, 234, 175–179.
- [25]Kumar, P. R.; Essehli, R.; Yahia, H. B.; Amin, R.; Belharouak, I. Electrochemical studies of a high voltage Na₄Co₃(PO₄)₂P₂O₇–MWCNT composite through a selected stable electrolyte, RSC Adv. 2020, 10, 15983.
- [26]Sanz, F.; Parada, C.; Amador, U.; Monge, M. A.; Valero, C. R. Na₄Co₃(PO₄)₂(P₂O₇), a new sodium cobalt phosphate containing a three-dimensional system of large intersecting tunnels. Journal of Solid State Chemistry 1996, 123(1), 129–139.
- [27]Moriwake, H.; Kuwabara, A.; Fisher, C. A.; Nose, M.; Nakayama, H.; Nakanishi, S.; Iba, H.; Ikuhara, Y. Crystal and electronic structure changes during the charge-discharge process of Na₄Co₃(PO₄)₂(P₂O₇). Journal of Power Sources 2016, 326, 220–225.
- [28]Liu, X.; Tang, L.; Li, Z.; Zhang, J.; Xu, Q.; Liu, H.; Wang, Y.; Xia, Y.; Cao, Y.; Ai, X. An Al-doped high voltage cathode of Na₄Co₃(PO₄)₂(P₂O₇) enabling highly stable 4 V full sodium-ion batteries, J. Mater. Chem. A 2019, 7(32), 18940–18949.
- [29]Zarrabeitia, M.; Casas-Cabanas, M.; Muñoz-Márquez, M. Á. Understanding the electrode–electrolyte interphase of high voltage positive electrode Na₄Co₃(PO₄)₂P₂O₇ for rechargeable sodium-ion batteries, Electrochimica Acta 2021, 372, 137846 (1–9).DOI
- [30]Dwivedi, P. K.; Nair, A.; Mehare, R. S.; Chaturvedi, V.; Joshi, K.; Shelke, M. V. Experimental and theoretical investigations of the effect of heteroatom-doped carbon microsphere supports on the stability and storage capacity of nano-Co₃O₄ conversion anodes for application in lithium-ion batteries. Nanoscale Advances 2020, 2(7), 2914–2924.DOI
- [31]Wang, L.; Zheng, Y.; Wang, X.; Chen, S.; Xu, F.; Zuo, L.; Wu, J.; Sun, L.; Li, Z.; Hou, H.; Song, Y. Nitrogen-doped porous carbon/Co₃O₄ nanocomposites as anode materials for lithium-ion batteries, ACS Appl. Mater. Interfaces 2014, 6, 7117–7125.DOI
- [32]Kim, H.; Lim, H.; Kim, H.-S.; Kim, K. J.; Byun, D.; Choi, W. Polydopamine-derived N-doped carbon-wrapped Na₃V₂(PO₄)₃ cathode with superior rate capability and cycling stability for sodium-ion batteries, Nano Res. 2019, 12(2), 397–404.DOI
- [33]Chen, W.; Wan, M.; Liu, Q.; Xiong, X.; Yu, F.; Huang, Y. Heteroatom-doped carbon materials: synthesis, mechanism, and application for sodium-ion batteries, Small Methods 2018, 1800323.
- [34]Sun, K.; Hu, Y.; Zhang, X.; Hui, K. S.; Zhang, K.; Xu, G.; Ma, J.; He, W. N-doped hard/soft double-carbon-coated Na₃V₂(PO₄)₃ hybrid-porous microspheres with pseudocapacitive behaviour for ultrahigh power sodium-ion batteries, Electrochimica Acta 2020, 335, 135680.DOI
- [35]Nevidomskyy, A. H.; Csányi, G.; Payne, M. C. Chemically active substitutional nitrogen impurity in carbon nanotubes, Phys. Rev. Lett. 2003, 91, 105502.
- [36]Latil, S.; Roche, S.; Mayou, D.; Charlier, J.-C. Mesoscopic transport in chemically doped carbon nanotubes, Phys. Rev. Lett. 2004, 92, 256805.
- [37]Senthilkumar, B.; Ananya, G.; Ramaprabhu, S. Synthesis of carbon coated nano-Na₄Ni₃(PO₄)₂(P₂O₇) as a novel cathode material for hybrid supercapacitors. Electrochimica Acta 2015, 169, 447–455.DOI
- [38]Gangadharan, R.; Kalaiselvi, J.; Shanmukaraj, D.; Palanivel, B.; Mohan, S.; Murugan, R. Ionic conductivity and Raman investigations on the phase transformations of Na₄P₂O₇. Journal of alloys and compounds 2002, 340(1-2), 95–100.DOI
- [39]Wang, D.; Chen, N.; Li, M.; Wang, C.; Ehrenberg, H.; Bie, X.; Wei, Y.; Chen, G.; Du, F. Na₃V₂(PO₄)₃/C composite as the intercalation-type anode material for sodium-ion batteries with superior rate capability and long-cycle life. J. Mater. Chem. A 2015, 3(16), 8636–8642.
- [40]Patra, J.; Wu, S.-C.; Leu, I.-C.; Yang, C.-C.; Dhaka, R. S.; Okada, S.; Chang, B. K.; Chang, J.-K. Comparison of hydrogenated anatase and rutile TiO₂ for sodium-ion battery anodes, ACS Appl. Energy Mater. 2021, 4, 5738–5746.DOI
- [41]Tang, K.; Fu, L.; White, R. J.; Yu, L.; Titirici, M. M.; Antonietti, M.; Maier, J. Hollow carbon nanospheres with superior rate capability for sodium-based batteries, Adv. Energy Mater. 2013, 2, 873–877.DOI
- [42]Dong, K.; Wang, Z.; Wang, D.; Sun, M.; Luo, S.; Liu, Y. Morphological evolution of hollow NiCo₂O₄ microspheres and their high pseudocapacitance contribution for Li/Na-ion battery anodes, New J. Chem. 2018, 42, 17762–17768.DOI
- [43]Palani, S.; Arumugam, S. Nano Co₃O₄ as anode material for Li-ion and Na-ion batteries: an insight into surface morphology, ChemSelect 2018, 3, 5040–5049.
- [44]Li, H. -H.; Li, Z. -Y.; Wu, X. L.; Zhang, L. -L.; Fan, C. -Y.; Wang, H. -F.; Li, X. Y.; Wang, K.; Sun, H. -Z.; Zhang, J. -P. Shale-like Co₃O₄ for high performance lithium/sodium ion batteries. J. Mater. Chem. A 2013, 4, 8242–8248.
- [45]Pang, Y.; Chen, S.; Xiao, C.; Ma, S.; Ding, S. MOF derived CoO-NCNTs two-dimensional networks for durable lithium and sodium storage, J. Mater. Chem. A 2019, 7, 4126–4133.DOI
- [46]Li, S.; Dong, Y.; Xu, L.; Xu, X.; He, L.; Mai, L. Effect of carbon matrix dimensions on the electrochemical properties of Na₃V₂(PO₄)₃ nanograins for high-performance symmetric sodium-ion batteries. Advanced Materials 2014, 26(21), 3545–3553.DOI
- [47]Wang, Q.; Dai, K.; Xie, Y.; Shui, M.; Shu, J. The prepa- Wang, D.; Wei, Z.; Lin, Y.; Chen, N.; Gao, Y.; Chen, G.; Song L.; Du, F. Intercalation pseudocapacitance in a NASICON-structured Na2CrTi(PO4)3 carbon nanocomposite: towards high-rate and long-lifespan sodium-ion-based energy storage, J. Mater. Chem. A 2019, 7, 20604–20613.
- [49]Pu, X.; Wang, H.; Yuan, T.; Cao, S.; Liu, S.; Xu, L.; Yang, H.; Ai, X.; Chen, Z.; Cao, Y. Na3Fe3(PO4)2(P2O7)/C nanospheres as low-cost, high-performance cathode material for sodium-ion batteries, Energy Storage Materials 2019, 22, 330-336.
- [50]Chen, C.; Wen, Y.; Hu, X.; Ji, X.; Yan, M.; Mai, L.; Hu, P.; Shan, B.; Huang, Y. Na+ intercalation pseudocapacitance in graphene-coupled titanium oxide enabling ultrafast sodium storage and long-term cycling, Nat. Comm. 2015, 6, 6929.DOI
- [51]Shukla R.; Dhaka, R. S. Anomalous magnetic and spin glass behavior in Nb-substituted LaCo1−xNbxO3. Phys. Rev. B 2018, 97, 024430(1–9).DOI
- [52]Kumar A.; Dhaka, R. S. Unraveling magnetic interactions and the spin state in insulating Sr2−xLaxCoNbO6. Phys. Rev. B 2020, 101, 094434(1–14).
- [53]Capraz, Ö. Ö.; Rajput, S; White, S.; Sottos, N. R. Strain evolution in lithium manganese oxide electrodes, Experimental Mechanics 2018, 58, 561–571.DOI
- [54]Jian, Z.; Sun Y.; Ji, X. A new low-voltage plateau of Na3V2(PO4)3 as an anode for Na-ion batteries, Chem. Commun. 2015, 51,6381–6383.
- [55]Wang, D.; Liu, Q.; Chen, C.; Li, M.; Meng, X.; Bie, X.; Wei, Y.; Huang, Y.; Du, F.; Wang, C.; Chen, G. NASICON-structured NaTi2(PO4)3/C nanocomposite as the low operation-voltage anode material for high-performance sodium-ion batteries, ACS Appl. Mater. Interfaces 2016, 8, 2238–2246.DOI
- [56]Wei, P.; Liu, Y.; Su, Y.; Miao, L.; Huang, Y.; Liu, Y.; Qiu, Y.; Li, Y.; Zhang, X.; Xu, Y.; Sun, X.; Fang, C.; Li, Q.; Han, J.; Huang, Y. F–doped NaTi2(PO4)3/C nanocomposite as a high-performance anode for sodium-ion batteries, ACS Appl. Mater. Interfaces 2019, 11, 3116–3124.
- [57]Wang, D.; Chen, N.; Li, M.; Wang, C.; Ehrenberg, H.; Bie, X.; Wei, Y.; Chen, G. Du, F. Na3V2(PO4)3/C composite as the intercalation-type anode material for sodium-ion batteries with superior rate capability and long-cycle life, J. Mater. Chem. A 2015, 3, 8636–8642.
- [58]Zhao, L.; Zhao, H.; Du, Z.; Wang, J.; Long, X.; Lia, Z.; Swierczek, K. Delicate lattice modulation enables superior Na storage performance of Na3V2(PO4)3 as both an anode and cathode material for sodium-ion batteries: understanding the role of calcium substitution for vanadium, J. Mater. Chem. A 2019, 7, 9807–9814.
- [59]Fang, Y.; Xiao, L.; Qian, J.; Cao, Y.; Ai, X.; Huang, Y.; Yang, H. 3D graphene decorated NaTi2(PO4)3 microspheres as a superior high-rate and ultracycle-stable anode material for sodium ion batteries, Adv. Energy Mater. 2016, 1502197 (1–8).
- [60]Qiu, S.; Wu, X.; Wang, M.; Lucero, M.; Wang, Y.; Wang, J.; Yang, Z.; Xu, W.; Wang, Q.; Gu, M.; Wen, J.; Huang, Y.; Xu, Z. J.; Fen, Z. NASICON-type Na3Fe2(PO4)3 as a low-cost and high-rate anode material for aqueous sodium-ion batteries, Nano Energy 2019, 64, 103941.