betaFeedback

WorksPhysics and Astronomy

High mobility SiMOSFETs fabricated in a full 300mm CMOS process

Abstract

The quality of the semiconductor-barrier interface plays a pivotal role in the demonstration of high quality reproducible quantum dots for quantum information processing. In this work, we have measured SiMOSFET Hall bars on undoped Si substrates in order to investigate the quality of the devices fabricated in a full CMOS process. We report a record mobility of 17'500 cm2/Vs with a sub-10 nm oxide thickness indicating a high quality interface, suitable for future qubit applications. We also study the influence of gate materials on the mobilities and discuss the underlying mechanisms, giving insight into further material optimization for large scale quantum processors.

The spin of an electron in Silicon has been considered as one of the most promising candidates for large-scale quantum computers, due to its long coherence time, compactness, potential to operate at relatively high temperatures, and compatibility with CMOS technology for upscaling [1, 2, 3]. High fidelity single and two qubit operations have been demonstrated in academic lab-based devices [4, 5]. The scale up process to multi-qubit arrays will however entail high quality qubits in large numbers, necessitating a transition to industrial fabrication techniques [6].

While spin qubit-devices can be fabricated using semiconductor manufacturing techniques, a detailed and careful analysis on the impact of different fabrication process steps on the performance of spin qubits is crucial. Hall-bar mobility is a widely used metric to characterize the MOS interface quality, which can provide valuable feedback to fabrication process optimization. In this work, we perform transport measurements on SiMOSFETs and investigate the quantum Hall effect. The gate stack for SiMOSFET is the same as that for qubit integration [7]. We extract key characteristics of the MOS gate stack such as critical density and mobility as well as transport and quantum lifetimes. Comparing the obtained results to a transport model, we identify and quantify the leading scattering terms. Additionally, we explore possible mobility limiting factors when changing the top gate material from PolySi to titanium nitride (TiN).

The devices measured in this work are undoped inversion gated Hall bars fabricated in a state-of-the art 300 mm fab line [7]. The starting substrate consists of a (100) silicon wafer with a background doping <5×1015 cm−3<5 \times10^{15}\ \mathrm{cm}^{-3}. The Hall bar top gates are defined by electron beam lithography and subsequent dry etching process, and the fanout metal pins are defined by deep UV lithography. After depositing the gate material, the whole wafer is covered with a passivation layer. In order to measure the electronic properties of the investigated samples, a positive voltage has been applied to the top gate to form a 2-dimensional electron gas (2DEG) at the interface of Si and SiO2\mathrm{SiO}_{2}.

Throughout this work, we perform four-wire electronic transport measurements using standard lock-in techniques. Both the longitudinal and transverse Hall voltages were measured simultaneously with differential voltage amplifiers. Additionally, the current through the sample was measured using an IV transimpedance amplifier. The measurements were carried out in a dilution refrigerator with a base temperature of 20 mK with a 9 T magnet. Higher temperatures were achieved by heating the mixing chamber, resulting in electron temperatures between 100 mK and 4.2 K.

Fig.1 shows the density and mobility study performed on a sample with a PolySi top gate at three different temperatures. First, the density of charge carriers in the 2DEG was extracted from the transverse Hall effect in the linear regime far from quantum oscillations, particularly at the lowest temperature with magnetic field between ±1\pm1 T. The density of charge carriers in the 2DEG has an overall linear dependence on the applied top gate voltage VGV_G as expected from a plate-capacitor model. Assuming the relative dielectric constant ϵr(SiO2)=3.9\epsilon_r(\mathrm{SiO}_{2}) = 3.9, we extract the thickness of the oxide and obtain a value of 8.1±0.18.1 \pm0.1 nm. This is in good agreement with the oxide thickness of 8 nm defined during the fabrication process. As one can see in the inset of Fig.1a, the extracted density deviates from a linear regime at very low VGV_G near the threshold voltage, particularly at the lowest temperature. A temperature dependent dielectric constant would result in a temperature dependent slope of the nSn_S regardless of the VGV_G [8], which is not observed in this study. Partial localization of charge carriers in the disorder potential at low sheet density, on the other hand, could explain this [9]. Here, the disorder potential is mainly due to bulk charge scattering and scattering from oxide charges. At these rather low densities close to the 2D Metal to Insulator Transition (MIT), partial localization would effectively reduce the sheet density of mobile carriers below a simple capacitor model, as observed, and thus slightly enhance the mobility, which is inversely proportional to the density.

The extracted densities, in combination with the sheet conductance from the longitudinal voltage measurements, allow for the calculation of the mobility μ\mu at various temperatures. The resulting curves are shown in Figure 1b. We measured a maximum mobility of 17.5×103 cm2/Vs17.5 \times10^{3}\,\mathrm{cm}^{2}/\mathrm{Vs}, among the highest mobility reported for SiMOSFET devices with sub 10 nm oxide thickness [10, 11, 12]. We fit the mobility curve with the Kruithof-Klapwijk-Bakker (KKB) model (Ref. [13]) which includes remote impurity scattering and surface roughness terms [13, 14]. Solving the model self-consistently for three separate temperatures (0.5, 0.9 and 4.2 K) yields the charged impurity center density NC=1.53±0.03×1010 cm−2N_C = 1.53 \pm0.03 \times10^{10}\,\mathrm{cm}^{-2}, the rms height of the amplitude of the interface roughness Δ=5.9±0.51 A˚\Delta= 5.9 \pm0.51\,\mathring{\mathrm{A}} and the correlation length L=1.8±0.35 nmL = 1.8 \pm0.35\,\mathrm{nm}. These numbers indicate a smooth and clean interface which is critical for future qubit implementations.

Figure 1. Density and Mobility study (a) Linear relationship between 2DEG sheet density nSn_{\mathrm{S}} and the top gate voltage VGV_{\mathrm{G}}. Below a top gate voltage of ≈0.4 V\approx0.4\ \mathrm{V} the extracted density deviates from the expected linear behaviour as shown in the inset. (b) Channel mobility μ\mu measured as a function of nSn_{\mathrm{S}} and corresponding fit to a mobility model (black) which includes scattering from charge impurities and surface roughness. The inset shows a SEM image of a similar device as the one used during the experiments with the same dimensions. (c) Channel mobility μ\mu trends with respect to temperature at various sheet densities. The symbols coincide with the ones used in panel b. The dashed lines are linear fits to the extracted mobilities and appear curved due to the logarithmic scale. (d) Longitudinal conductivity σxx\sigma_{xx} in the low density range and fit to a percolation theory (black). A linear trend with respect to temperature for npn_{\mathrm{p}} is observed in the inset.

As shown in Figure 1b, there is a slight deviation of the maximum mobility from the theory curve at 0.9 K, and the theoretical curve does not agree with the reported data for 0.1 K in the low density regime. This could be explained by the assumption of a linear relationship between mobility and temperature in the KKB theory. According to our fitting, this assumption seems to be only valid above 1 K and can become a more complex function of temperature below 1 K if the low density regime becomes non-linear. This is due to the fact that the slightly reduced density (compared to the capacitor model) results in a slightly higher mobility, explaining the deviation of our data from the theory. Furthermore, for sheet densities nSn_S close to the depletion charge density ndepn_{dep}, the calculation of the finite extent of the wave function in the KKB theory can become unreliable because of the assumed approximations. The theoretically predicted curve can be recovered by using a linearly extrapolated density during the calculation of the mobility. Further details are discussed in Appendix A.

Another key parameter is the percolation density, which indicates the minimum density required to form a conducting channel. Generally, the percolation density describes the disorder in the channel at low densities, where quantum devices typically operate. In Figure 1d, we employed a MIT model in order to fit the density-dependent conductivity σxx∼(n−np)p\sigma_{xx} \sim(n-n_p)^p [15], where npn_p and pp are the percolation density and universal exponent, respectively. However, this model is only valid in the low density regime and deviates above n=8×1011 cm−2n=8\times10^{11}\,\mathrm{cm}^{-2}. We fixed the exponent p=1.31p=1.31, as expected in a two-dimensional system, and allowed npn_p to vary [15]. Our fits yield np=1.86×1011 cm−2n_p=1.86\times10^{11}\,\mathrm{cm}^{-2} at T=4.2 KT=4.2\,\mathrm{K}. As seen in the inset of Figure 1d the extracted npn_p decreases with decreasing temperature, which is in agreement with previous studies [15], and is below 1×1011 cm−21\times10^{11}\,\mathrm{cm}^{-2} at the lowest temperature. Such a low percolation density is among the lowest reported for similar devices [12, 16]. The small percolation density and high peak mobility indicate low interface disorder of the MOS gate stack, which is crucial for large scale quantum dot arrays.

Additionally, we investigate the temperature dependence of mobility at various top gate voltages. For sheet densities less than 2×1012 cm−22\times10^{12}\,\mathrm{cm}^{-2} the mobility is a function of temperature, with a linear dependence for temperatures above 1 K (see Figure 1c). The temperature dependence of the mobility is only visible for low electron densities because mobilities at higher densities are limited by surface roughness, which is not temperature dependent. Additionally, the peak mobility shifts to higher densities at higher temperatures due to the activation of background charges limiting the mobility at high temperatures.

In order to extract more information about the transport properties and the dominating scattering mechanism, we investigated the transverse resistance RxyR_{xy} and longitudinal resistivity ρxx\rho_{xx} in the quantum Hall regime. The magnetic field BB was swept up to 8.5 T at a fixed sheet density of 7.1×1011 cm−27.1\times10^{11}\,\mathrm{cm}^{-2} near the peak mobility. As shown in Figure 2a, we observe Shubnikov-De Haas (SdH) oscillations starting at 0.8 T and begin to resolve spin splitting at 3.2 T. The ρxx\rho_{xx} shows well developed zeros for magnetic fields larger than 3.8 T. In combination with the single frequency of the SdH oscillations extracted below 2.5 T and the absence of beatings strongly indicate single subband occupancy. We further observe a four-fold degeneracy in the filling factor which changes to a two-fold degeneracy as we increased the magnetic field (Figure 2b). The remaining two-fold degeneracy is due to the two lowest lying valleys which are split off from the remaining four valleys due to the z-confinement in Silicon (100) [17]. A linear fit of the filling factor (Figure 2b) with respect to inverse magnetic field yields a sheet density 7.1×1011 cm−27.1\times10^{11}\,\mathrm{cm}^{-2} in agreement with the extracted Hall density, further confirming clean single subband transport in the investigated samples.

Figure 2. Extended Hall studies with transport properties (a) Longitudinal resistivity ρxx\rho_{xx} (blue) and transverse resistance RxyR_{xy} (black) at nS=7.1×1011 cm−2n_{\mathrm{S}} = 7.1 \times10^{11}\ \mathrm{cm}^{-2} as a function of magnetic field BB. The arrow indicates the magnetic field spin is resolved. (b) Linear relationship between filling factor ν\nu (blue scatter) and inverse magnetic field. The solid line is a fit from which the sheet density is calculated. (c) and (d) Extracted dingle ratio τt/τq\tau_{\mathrm{t}/\tau_{\mathrm{q}}} as a function of temperature TT and sheet density nSn_{\mathrm{S}}, respectively. The dingle ratio is slightly temperature and density dependent and is ≈1\approx1, which indicates that large angle scattering is most dominant scattering mechanism in this sample.

Upon further investigations into the SdH oscillation amplitudes below 2.5 T, we were able to extract an effective mass m∗=0.21±0.02⋅m0m^*=0.21\pm0.02\cdot m_0 from the temperature dependent data, which corresponds to the transverse mass expected for Silicon samples with similar background doping [18]. Further details are discussed in Appendix B. From fitting the SdH envelope as a function of temperature and density, we can extract the quantum lifetime τq\tau_q. By combining τq\tau_q, which includes all possible scattering events, and the transport lifetime τt=e∗μ/m∗\tau_t=e^*\mu/m^*, which includes only the large angle scattering, we extract the so-called Dingle ratio τt/τq\tau_t/\tau_q. The Dingle ratio thus characterizes the dominant scattering mechanism ranging from a ratio of 1 for predominant large angle scattering to values ≫1\gg1 for dominant small angle scattering. Figure 2c shows an increase of the Dingle ratio from ≈1\approx1 to ≈2\approx2 with increasing temperature, indicating a shift in the type of scattering dominating at different temperature ranges. We can see an inverted trend for the Dingle ratio with respect to density. For a fixed temperature of 0.5 K, we observe a decrease from a ratio of ≈1.5\approx1.5 to ≈1\approx1 by increasing the density, again showing a slight shift towards large angle scattering. This is true for all measured temperatures and densities. In all, the observed Dingle ratio around 1 to 2 shows that short range / large angle scattering is the dominant scattering mechanism in this system, where the scattering centers are near or in the channel itself [18].

Furthermore, we investigate the effect of two different gate metals on the mobility and percolation density. We chose PolySi and titanium nitride (TiN) as top gate materials since both are widely applied gating materials for integrated CMOS device fabrication. While PolySi has generally larger mobilities, which indicates a small disorder potential and therefore a low dot-to-dot variation, TiN exhibits low resistivity and is superconducting at low temperatures, which is desirable for microwave qubit control and readout. The density dependent mobilities at 4.2 K, for both TiN and PolySi are shown in Figure 3a. There is a decrease by a factor of three in the maximum mobility when changing the material from PolySi to TiN while all other parameters in the fabrication remain the same. To investigate the underlying mechanism for the mobility difference, we perform high magnetic field Hall measurements on the TiN devices as well. Unlike PolySi which shows vanishing ρxx\rho_{xx} in Figure 2a, ρxx\rho_{xx} of TiN does not have well developed zeros. This can be attributed to the lower mobility and could be due to multiple subband transport [19] (see Appendix § 0.4.3 for further details). At high electron concentrations and in the presence of compressive stress, multiple subbands can be occupied and thus introduce inter-subband scattering at low temperatures.

Figure 3. Gate material study (a) The channel mobility μ\mu with respect to sheet density nSn_{\mathrm{S}} for PolySi (green) and TiN (violet), both at 4.2 K. The mobility shows a decrease by a factor of three when changing the top gate material from PolySi to TiN. (b) Longitudinal conductivity σxx\sigma_{xx} with respect to sheet density. The fits to percolation theory (black) show a significant difference between the PolySi and TiN percolation densities.

To explain the inter-subband scattering, we firstly consider the effect of strain. On silicon (100) surfaces, materials used as top gates with certain coefficient of thermal expansion (CTE) introduce compressive strain [20]. This leads to a decrease in the energy splitting of two subsequent subbands [18, 21, 22]. Strain simulations, described in Appendix § 0.4.4, indicate a large difference in strain between TiN and PolySi. However, the strain could only decrease the TiN mobility by roughly 10 percent rather than the three fold decrease observed [22]. This difference could be explained by the oxygen scavenging of TiN on SiO2_2 [23]. When depositing TiN on a SiO2_2 surface, SiO2_2 gets reduced to SiOx_x and the free oxygen combines with TiN to form TiO2_2 and titanium oxynitride (TiNx_xOy_y). This process creates charged oxygen vacancies in the SiO2_2 layer and because the oxide is very thin in these samples, the charge carriers can then scatter at these defects thus reducing the overall mobility. Indeed, fits of the KKB model to the TiN data indicate a significantly higher NCN_C than PolySi consistent with the scavenging hypothesis. Those two effects combined therefore could explain the difference in mobilities between the two gate metals.

In summary, we have characterized SiMOSFET samples using Hall effect measurements. We found a record mobility of 17.5×10317.5 \times10^3 cm2^2/Vs which is the highest reported mobility to date for SiMOSFET samples with sub-10 nm oxide thickness. Further, we have shown that the dominant mobility limiting factor are charges near the conducting channel, which can be improved by further reducing the impurity levels in the substrate. For example, an epitaxial layer can reach a background doping level of roughly 1×10121 \times10^{12} cm−3^{-3}, which is three orders of magnitude lower than the samples measured in this study. Additionally, we show that the choice of top gate material directly affects the mobility and percolation density. Factors such as strain and oxygen scavenging could explain the strong influence on both parameters. This demonstrates that the choice of top gate material is of paramount importance. The MOS interface has been widely identified as the source for charge noise and disorder sites, which limits the qubit performance and upscaling. To further improve the qubit device fabrication, more systematical investigations are needed. The Hallbar mobility and the analysis presented in this study could provide valuable insight into the gate stack over a large device area and direct further fabrication optimizations, which could pave the way for a large scale spin qubit processor integration with a full CMOS process.

Acknowledgements

This work was performed as part of imec’s Industrial Affiliation Program (IIAP) on Quantum Computing. Additionally, this work was supported by the Swiss Nanoscience Institute (SNI), the Swiss National Science Foundation (SNF), the National Centers of Competence in Research (NCCR) SPIN and the EU H2020 European Microkelvin Platform (EMP) grant No. 824109.

Author contributions

T.N.C., A.E. and D.M.Z performed the experiments, analysed the measurements and wrote the manuscript with input from all authors. B.G. designed the test structures. S.K. and J.J. fabricated the devices. F.A.M. performed the strain simulations. The work was completed with assistance from R.L., P.V.D. and I.R..

Data availability statement

The data supporting the plots of this paper are available at the Zenodo repository at https://doi.org/10.5281/zenodo.xxxxx.

Appendix

Mobility as a function of linear density and MIT fitting range

During the calculation of the mobility at the lowest temperature, we observed a peak mobility higher than the KKB model (see Figure 1b). We associated this deviation to the non-linear density dependence in the small top gate voltage regime at the lowest temperature as shown in the inset of Figure 1a. This assumption is further supported because the theoretical curve can be recovered using a linear extrapolated density when calculating the mobility (see Figure 4). This behaviour can be explained within the KKB theory, where the depletion charge density ndepn_{\mathrm{dep}} is implicitly assumed to be significantly smaller than the sheet density nSn_{\mathrm{S}} especially in the critical regime of maximum mobility [13]. If the density becomes non-linear, this violation of the linear density assumption has a significant impact when calculating the finite extent of the wave function bb within the Coulomb scattering term ⟨∣UC(q)∣2⟩\langle|U_{\mathrm{C}}(q)|^{2}\rangle and the dielectric response function ε\varepsilon. Further research in this regime is needed in order to capture the behaviour found in this work, but it exceeds the scope of this work. Nevertheless, we emphasize the mobility of 17.5×103 cm2/Vs17.5 \times10^{3}\ \mathrm{cm}^{2}/\mathrm{Vs} is the properly measured mobility, and the slightly lower peak mobility of 16.5×103 cm2/Vs16.5 \times10^{3}\ \mathrm{cm}^{2}/\mathrm{Vs} in Figure 4 is a modeled mobility assuming a linear density model. The previous mobility record was ≈10×103 cm2/Vs\approx10 \times10^{3}\ \mathrm{cm}^{2}/\mathrm{Vs} for a comparable sample although the oxide was slightly thicker in that work [12].

Figure 4. Mobility as a function of linear density and MIT fitting range (a) When using a linearly extrapolated (instead of the carefully extracted) density in order to calculate the mobility of our sample (blue), the peak mobility becomes slightly smaller than previously demonstrated in Figure 1b. Additionally, we can fit the KKB theory (black) self-consistently with the other temperature data highlighting the importance of the density values. (b) By varying ΔnS\Delta n_{\mathrm{S}} for extracting the percolation density npn_{\mathrm{p}} within the metal to insulator transition (MIT) model, we determine the optimal fitting range. We chose ΔnS=3.2×1011 cm−2\Delta n_{\mathrm{S}}=3.2 \times10^{11}\ \mathrm{cm}^{-2} (indicated by the red box) because the extracted npn_{\mathrm{p}} does not change significantly while changing ΔnS\Delta n_{\mathrm{S}}.

The metal to insulator transition model (MIT) we used in this work is only valid at very low densities (below 1×1012 cm−21 \times10^{12}\ \mathrm{cm}^{-2} and therefore is rather sensitive to the fitting range. In order to find the appropriate fitting range, we varied both the minimum and maximum value independently. As shown in Figure 4, we determined that fitting the data between 2.7×1011 cm−22.7 \times10^{11}\ \mathrm{cm}^{-2} and 6.0×1011 cm−26.0 \times10^{11}\ \mathrm{cm}^{-2} yields the most reliable outcome because variations in the fitting range do not significantly change the result.

Extraction of effective mass and quantum lifetime

In order validate our evaluation approach and our experiments, we extract the effective mass from the temperature dependence of the SdH oscillations. For that, we subtract a polynominal background from the ρxx\rho_{xx} data and use the following formula as described in [24, 25]

Δρxx(T)Δρxx(T0)=TT0⋅sinh⁡χ(T)sinh⁡χ(T0)(1)\frac{\Delta\rho_{xx}(T)}{\Delta\rho_{xx}(T_{0})} = \frac{T}{T_{0}}\cdot\frac{\sinh\chi(T)}{\sinh\chi(T_{0})} \tag*{(1)}

with χ(T)=2π2kBT/ℏωc\chi(T) = 2\pi^{2}k_{\mathrm{B}}T/\hbar\omega_{\mathrm{c}} and ωc=eB/m∗\omega_{\mathrm{c}} = eB/m^{*}. Here, TT is the temperature, T0T_{0} the lowest temperature, kBk_{\mathrm{B}} is the Boltzmann constant, ℏ\hbar the reduced Planck constant, ee the electric charge, BB the magnetic field and m∗m^{*} the effective mass. Using the effective mass as the only free fit parameter, we extracted m∗=0.21±0.02⋅m0m^{*} = 0.21 \pm0.02 \cdot m_{0}, which is close to the expected value of m∗=0.19⋅mem^{*} = 0.19 \cdot m_{\mathrm{e}}.

Further, the envelope of the SdH oscillations allows for the extraction of the quantum lifetime τq\tau_{q}. For that, we use the following formula

ln⁡(Δρxx(B)sinh⁡χχ)=C−πm∗eBτq(2)\ln\left(\frac{\Delta\rho_{xx}(B)\sinh\chi}{\chi}\right) = C - \frac{\pi m^{*}}{eB\tau_{q}} \tag*{(2)}

Therefore, by analysing the slope of the magnetic field dependent logarithmic term we can extract τq\tau_{q} for all measured densities and temperatures. In combination with the transport lifetime τt\tau_{t} we can then further extract the dingle ratio as described in the main text.

TiN data at high fields

In comparison to the reported data in Figure 2a, TiN does not show well developed zeroes in the longitudinal resistivity ρxx\rho_{xx} at high magnetic fields at a temperature of 500 mK (see Figure 7), as expected for a much lower mobility. Further, the transversal Hall resistance RxyR_{xy} shows oscillating features instead of the expected Hall plateaus. This could be due to multiple subbands contributing to the overall transport or with the increased density of background charges due to the above mentioned oxygen scavenging.

Gate material strain simulations

Figure 7. Gate material strain simulations (a) Schematic of the Hall bar used for the strain simulation. The strain in the channel was calculated using sprocess in the region indicated by the dashed white line. (b, c) The strain in the channel for the PolySi and TiN respectively. The model uses literature values for the thermal expansion coefficient for both materials.

Strain simulations

We quantify the strain induced in the 2DEG due to the different thermal expansion coefficients of both gate materials. The strain was simulated using a commercially available software [26]. The silicon was simulated isotropically. The temperature dependence of the CTE for PolySi up to room temperature is assumed to be linear because there is no reported data above 200 K [27]. Further, we neglect the intrinsic strain induced during the fabrication process, which is beyond the scope of this work. Thermal contraction is considered from room temperature down to the cryogenic measurement temperatures. All simulations were performed in three dimensions and the components of strain εx,εy,εz\varepsilon_{x}, \varepsilon_{y}, \varepsilon_{z} are calculated 5 nm below the oxide due to the finite extension of the wavefunction. As shown in Figure 7b and Figure 7c, there is a large difference in strain between TiN and PolySi. While TiN induces strain up to 2.4×10−42.4 \times10^{-4}, PolySi induces significantly less strain of approximately only 0.28×10−40.28 \times10^{-4}.

References

Figure 5. SdH oscillations (a) We can extract the effective mass by analysing the temperature dependent SdH oscillations at various magnetic field values BB. (b) The envelope of the SdH oscillations in the fully spin and valley degenerate regime (<2.5 T< 2.5\ \mathrm{T}) we can extract the quantum lifetime τq\tau_q for various densities. Curves are offset for clarity.

Figure 6. TiN data at high fields Longitudinal resistivity ρxx\rho_{xx} (blue) and transverse Hall resistance RxyR_{xy} (black) of the sample measured with a TiN top gate at 500 mK. Both the not well developed zeroes in ρxx\rho_{xx} and the oscillating RxyR_{xy} indicate multiple subband occupancy.

References

  1. [1]L. Vandersypen, H. Bluhm, J. Clarke, A. Dzurak, R. Ishihara, A. Morello, D. Reilly, L. Schreiber, and M. Veldhorst. Interfacing spin qubits in quantum dots and donors—hot, dense, and coherent. npj Quantum Information 3, 1 (2017).DOI
  2. [2]J. R. Petta, A. C. Johnson, J. M. Taylor, E. A. Laird, A. Yacoby, M. D. Lukin, C. M. Marcus, M. P. Hanson, and A. C. Gossard. Coherent manipulation of coupled electron spins in semiconductor quantum dots. Science 309, 2180 (2005).pubmed.ncbi.nlm.nih.gov/16141370
  3. [3]M. Veldhorst, J. Hwang, C. Yang, A. Leenstra, B. de Ronde, J. Dehollain, J. Muhonen, F. Hudson, K. M. Itoh, A. Morello, et al. An addressable quantum dot qubit with fault-tolerant control-fidelity. Nature nanotechnology 9, 981 (2014).DOI
  4. [4]R. Maurand, X. Jehl, D. Kotekar-Patil, A. Corna, H. Bohuslavskyi, R. Lavieville, L. Hutin, S. Barraud, M. Vinet, M. Sanquer, et al. A CMOS silicon spin qubit. Nature communications 7, 1 (2016).DOI
  5. [5]M. Veldhorst, C. Yang, J. Hwang, W. Huang, J. Dehollain, J. Muhonen, S. Simmons, A. Laucht, F. Hudson, K. M. Itoh, et al. A two-qubit logic gate in silicon. Nature 526, 410 (2015).DOI
  6. [6]R. Li, L. Petit, D. P. Franke, J. P. Dehollain, J. Helsen, M. Steudtner, N. K. Thomas, Z. R. Yoscovits, K. J. Singh, S. Wenner, et al. A crossbar network for silicon quantum dot qubits. Science advances 4, eaar3960 (2018).
  7. [7]R. Li, N. D. Stuyck, S. Kubicek, J. Jussot, B. Chan, F. Mohiyaddin, A. Elsayed, M. Shehata, G. Simion, C. Godfrin, et al. A flexible 300 mm integrated Si MOS platform for electron-and hole-spin qubits exploration. In 2020 IEEE International Electron Devices Meeting (IEDM), 38–3 (IEEE, 2020).
  8. [8]P. Lautenschlager, M. Garriga, L. Vina, and M. Cardona. Temperature dependence of the dielectric function and interband critical points in silicon. Physical Review B 36, 4821 (1987).pubmed.ncbi.nlm.nih.gov/9943498
  9. [9]M. Tsukada. On the tail states of the landau subbands in MOS structures under strong magnetic field. Journal of the Physical Society of Japan 41, 1466 (1976).DOI
  10. [10]S. Shankar, A. Tyryshkin, J. He, and S. Lyon. Spin relaxation and coherence times for electrons at the Si/SiO 2 interface. Physical Review B 82, 195323 (2010).
  11. [11]S. Rochette, M. Rudolph, A.-M. Roy, M. Curry, G. T. Eyck, R. Manginell, J. Wendt, T. Pluym, S. Carr, D. Ward, et al. Quantum dots with split enhancement gate tunnel barrier control. Applied Physics Letters 114, 083101 (2019).DOI
  12. [12]D. Sabbagh, N. Thomas, J. Torres, R. Pillarisetty, P. Amin, H. George, K. Singh, A. Budrevich, M. Robinson, D. Merrill, et al. Quantum Transport Properties of Industrial Si 28/Si O 2 28. Physical Review Applied 12, 014013 (2019).DOI
  13. [13]G. Kruithof, T. Klapwijk, and S. Bakker. Temperature and interface-roughness dependence of the electron mobility in high-mobility Si (100) inversion layer below 4.2 K. Physical Review B 43, 6642 (1991).pubmed.ncbi.nlm.nih.gov/9998107
  14. [14]A. Gold and V. Dolgopolov. Temperature dependence of the conductivity for the two-dimensional electron gas: Analytical results for low temperatures. Physical Review B 33, 1076 (1986).pubmed.ncbi.nlm.nih.gov/9938372
  15. [15]L. Tracy, E. Hwang, K. Eng, G. Ten Eyck, E. Nordberg, K. Childs, M. Carroll, M. Lilly, and S. D. Sarma. Observation of percolation-induced two-dimensional metal-insulator transition in a Si MOSFET. Physical Review B 79, 235307 (2009).DOI
  16. [16]J.-S. Kim, A. M. Tyryshkin, and S. A. Lyon. Annealing shallow Si/SiO2 interface traps in electron-beam irradiated high-mobility metal-oxide-silicon transistors. Applied Physics Letters 110, 123505 (2017).DOI
  17. [17]F. Herman. The electronic energy band structure of silicon and germanium. Proceedings of the IRE 43, 1703 (1955).DOI
  18. [18]T. Ando, A. B. Fowler, and F. Stern. Electronic properties of two-dimensional systems. Reviews of Modern Physics 54, 437 (1982).DOI
  19. [19]G. Kruithof and T. Klapwijk. Electron transport with two occupied subbands in a Si (100) inversion layer. Physical Review B 42, 11412 (1990).pubmed.ncbi.nlm.nih.gov/9995443
  20. [20]F. Nix and D. MacNair. The thermal expansion of pure metals: copper, gold, aluminum, nickel, and iron. Physical Review 60, 597 (1941).DOI
  21. [21]S. Kawaji, K. Hatanaka, K. Nakamura, and S. Onga. Mobility Hump and Inversion Layer Subbands in Si on Sapphire. Journal of the Physical Society of Japan 41, 1073 (1976).DOI
  22. [22]I. Eisele. Stress and intersubband correlation in the silicon inversion layer. Surface Science 73, 315 (1978).DOI
  23. [23]E. O. Filatova, S. S. Sakhonenkov, A. S. Konashuk, S. A. Kasatikin, and V. V. Afanas’ ev. Inhibition of Oxygen Scavenging by TiN at the TiN/SiO2 Interface by Atomic-Layer-Deposited Al2O3 Protective Interlayer. The Journal of Physical Chemistry C 123, 22335 (2019).
  24. [24]G. Bauer and H. Kahlert. Low-temperature non-ohmic galvanomagnetic effects in degenerate n-type InAs. Physical Review B 5, 566 (1972).DOI
  25. [25]O. Celik, E. Tiras, S. Ardali, S. B. Lisesivdin, and E. Ozbay. Determination of the in-plane effective mass and quantum lifetime of 2D electrons in AlGaN/GaN based HEMTs. physica status solidi c 8, 1625 (2011).DOI
  26. [26]Sentaurus Process - Technology Computer Aided Design (TCAD) — Synopsys.” https://www.synopsys.com/silicon/tcad/process-simulation/sentaurus-process.html.
  27. [27]T. Thorbeck and N. M. Zimmerman. Formation of strain-induced quantum dots in gated semiconductor nanostructures. AIP Advances 5, 087107 (2015).

Paper details

vlnc:W_d5wf2xut
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents