betaFeedback

WorksMathematics

Electric combined-field-only P1 Galerkin BEM for PEC scattering with scalar Helmholtz operators

Abstract

We develop a Galerkin boundary element method for the indirect electric combined-field-only integral equation (ECFOIE) for perfectly electrically conducting obstacles with smooth surfaces. The method is free of low-frequency breakdown and of spurious resonances. It applies scalar Helmholtz operators componentwise, so that fast scalar solvers can be reused, with less memory than a Rao-Wilton-Glisson (RWG) discretization. The iteration count of the Calderón-regularized ECFOIE (R-ECFOIE) is constant under mesh refinement and, with a complex-wavenumber Calderón regularizer, grows only mildly with frequency. The discretization uses continuous, nodal piecewise-linear basis functions on flat triangular meshes, with essentially as many unknowns as an RWG discretization, and tangential and normal projections and the mean curvature of the obstacle's surface carry the vector structure. On flat meshes the curvature is concentrated on the edges, and we average the edge measure obtained from the first variation of area over vertex patches, which gives sparse curvature matrices. At low frequency, four Lagrange-multiplier constraints on the induced charge and on the longitudinal dipole moments of the far field keep the R-ECFOIE accurate in the quasi-static regime, tested on scatterers eight orders of magnitude smaller than the wavelength. Under mesh refinement, the errors decrease at about second order. A Helmholtz resonator, a rounded Fichera cube, and a smoothed Stanford bunny are compared with electric field integral equation (EFIE) solutions, and the first two also with electrostatic references at extreme low frequency.

Introduction

TIME-HARMONIC electromagnetic scattering by perfectly electrically conducting (PEC) obstacles is commonly treated with boundary integral equations (BIEs) for the surface current, most notably the electric, magnetic, and combined field integral equations [1]. Their Galerkin discretization with Rao–Wilton–Glisson (RWG) functions [2], commonly referred to as the method of moments, gives rise to dense linear systems whose solution can be accelerated by fast multipole methods or compressed using hierarchical matrices [3]. The surface-current densities belong to tangential trace spaces with subtle regularity properties, and the corresponding Galerkin theory differs substantially from that of scalar integral equations [4]. Calderón preconditioning moreover requires compatible dual basis functions [5]. The EFIE also suffers from low-frequency breakdown, which can be addressed through loop–star, loop–tree, and quasi-Helmholtz decompositions [6], [7]. Other low-frequency-stable approaches include current-and-charge [8] and Debye-source [9] formulations. High-order Nyström methods have also been developed [10]–[14]. A different line of work, the so-called field-only surface integral equations [15]–[17], avoids surface currents altogether by solving vector Helmholtz problems for the Cartesian components of the field, using a boundary condition on the normal component of the normal derivative of the electric field [17], [18]. The Maxwell à la Helmholtz framework rigorously establishes that this vector Helmholtz problem is equivalent to the PEC scattering problem and yields indirect [19] and direct [20] second-kind combined-field formulations that are uniquely solvable at all frequencies and have so far been discretized with high-order Nyström methods [21].

The indirect ECFOIE of [19] is developed for C2,αC^{2,\alpha}-smooth PEC surfaces. It prescribes the tangential electric trace and couples the normal component of its normal derivative to the obstacle’s surface mean curvature. The resulting BIE involves only the classical scalar Helmholtz single-layer, double-layer, adjoint double-layer, and hypersingular operators, denoted by SkS_k, KkK_k, Kk′K_k', and TkT_k, respectively, applied componentwise, while tangential and normal projections and the curvature carry the remaining vector structure. We investigate whether it can be accurately discretized with standard continuous P1 densities on flat triangles while retaining the curvature contribution in its variational form. With three components per vertex, a closed mesh with NN vertices gives 3N3N unknowns, while an RWG discretization [2] has one per edge, that is, 3N−63N-6 on a genus-zero surface by Euler’s formula.

The use of standard flat triangular meshes enables practical ECFOIE computations on a broader range of smooth surfaces, including surfaces given only implicitly as level sets, which can be meshed with general-purpose generators such as Gmsh [22]. It does not, however, remove the regularity requirement on the underlying geometry, which is a property of the formulation and not of its discretization. Genuinely sharp edges remain outside its scope. Indeed, the componentwise Helmholtz setting requires fields in H1H^1, whereas PEC fields on polyhedral obstacles lie naturally in H(curl⁡)∩H(div⁡)H(\operatorname{curl}) \cap H(\operatorname{div}) but generally fail to have H1H^1 regularity because of edge singularities [23]. Consequently, nodal H1H^1-conforming discretizations do not in general converge to such fields [24]. Section IV-C studies this on surfaces of controlled regularity. The method is thus intended for smooth or rounded scatterers. For these, it is stable at low frequencies without loop–star or quasi-Helmholtz decompositions, uses only scalar Helmholtz operators, so that existing Helmholtz fast multipole and hierarchical-matrix codes can be reused, and gives iteration counts that do not grow under mesh refinement with less memory than an RWG EFIE.

We evaluate the singular integrals with Sauter–Schwab quadrature [25] and the hypersingular operator in weak form through Maue’s identity, discretize the mean curvature variationally following [26, 27], impose the low-frequency constraints with Lagrange multipliers, and recover the surface current weakly from the traces. Section II summarizes the formulation and the constraints, Section III develops the discretization, Section IV presents the numerical results, and Section V discusses scope and limitations.

Electric Field-Only Formulation

Let Ω⊂R3\Omega\subset\mathbb{R}^{3} be a bounded PEC obstacle with a connected boundary Γ\Gamma of class C2,αC^{2,\alpha}, 0<α<10 < \alpha< 1, and outward unit normal ν\nu, embedded in a homogeneous medium with permittivity ϵ\epsilon, permeability μ\mu, and wave impedance Z=μ/ϵZ = \sqrt{\mu/\epsilon}. Fields are time-harmonic with time dependence e−iωte^{-i\omega t}, and the wavenumber is k=ωϵμk = \omega\sqrt{\epsilon\mu}. We use the outgoing Green function

Gk(x,y)=eik∣x−y∣4π∣x−y∣,x≠y,k≥0.(1)G_k(x,y)=\frac{e^{ik\lvert x-y\rvert}}{4\pi\lvert x-y\rvert},\qquad x\ne y,\quad k\ge0. \tag*{(1)}

For a sufficiently smooth scalar density φ\varphi on Γ\Gamma, the single- and double-layer potentials are

Skφ=∫ΓGk(⋅,y)φ(y) dsy,Dkφ=∫Γ∂νyGk(⋅,y)φ(y) dsy(2)S_k\varphi=\int_{\Gamma}G_k(\cdot,y)\varphi(y)\,{\rm d}s_y,\qquad D_k\varphi=\int_{\Gamma}\partial_{\nu_y}G_k(\cdot,y)\varphi(y)\,{\rm d}s_y \tag*{(2)}

off Γ\Gamma. The boundary operators SkS_k, KkK_k, Kk′K_k', and TkT_k are the classical boundary integral operators of the Helmholtz equation [28], with kernels GkG_k, ∂νyGk\partial_{\nu_y}G_k, ∂νxGk\partial_{\nu_x}G_k, and ∂νx∂νyGk\partial_{\nu_x}\partial_{\nu_y}G_k, the last in the sense of the Hadamard finite part. We denote by γ±\gamma^\pm and ∂ν±\partial_\nu^\pm the Dirichlet and Neumann traces on Γ\Gamma, that is, the limits of a function and of its normal derivative as Γ\Gamma is approached from the exterior (+)(+) or the interior (−)(-), with the outward normal ν\nu (understood as a column vector) in both cases. They are applied componentwise to vector fields, and for fields that are smooth across Γ\Gamma, such as the incident field, we drop the superscript. They are related to the layer potentials by the jump relations [28]

γ±(Skφ)=Skφ,γ±(Dkφ)=±12φ+Kkφ,\gamma^\pm(S_k\varphi)=S_k\varphi,\qquad\gamma^\pm(D_k\varphi)=\pm\frac{1}{2}\varphi+K_k\varphi,
∂ν±(Skφ)=∓12φ+Kk′φ,∂ν±(Dkφ)=Tkφ.(3)\partial_\nu^\pm(S_k\varphi)=\mp\frac{1}{2}\varphi+K_k'\varphi,\qquad\partial_\nu^\pm(D_k\varphi)=T_k\varphi. \tag*{(3)}

For the total electric field E=Ei+EsE=E^i+E^s, set Pt=I−ννTP_t=I-\nu\nu^{T}, Pν=ννTP_\nu=\nu\nu^{T}, and let H=12div⁡Γν\mathcal{H}=\frac{1}{2}\operatorname{div}_{\Gamma}\nu be the mean curvature (so H=1\mathcal{H}=1 on the unit sphere). The field-only problem in [19] imposes the vector Helmholtz equation ΔEs+k2Es=0\Delta E^s+k^2E^s=0 in R3∖Ω‾\mathbb{R}^{3}\setminus\overline{\Omega}, with the Sommerfeld radiation condition on each component of EsE^s, together with

Ptγ+E=0,Pν(∂ν+E+2Hγ+E)=0.(4)P_t\gamma^+E=0,\qquad P_\nu(\partial_\nu^+E+2\mathcal{H}\gamma^+E)=0. \tag*{(4)}

The first boundary condition is the standard PEC condition ν×E=0\nu\times E=0. The second replaces the divergence constraint: when Ptγ+E=0P_t\gamma^+E=0, it is equivalent to γ+(div⁡E)=0\gamma^+(\operatorname{div}E)=0 [19 Lemma 3.2]. Since div⁡Es\operatorname{div}E^s is then an outgoing Helmholtz solution with zero Dirichlet data, it vanishes, so EE is divergence-free and solves Maxwell’s equations. For a C2,αC^{2,\alpha} boundary, this vector Helmholtz problem is therefore equivalent to the classical PEC scattering problem [19 Thm. 3.4].

The scattered field is then represented by the combined-field ansatz

Es=(Dk−iηSk)φ,(5)E^s=(D_k-i\eta S_k)\varphi, \tag*{(5)}

where φ:Γ→C3\varphi:\Gamma\to\mathbb{C}^{3} is an auxiliary density and η>0\eta>0 is a coupling parameter. (We omit the finite-rank point-source term of [19], which on flat triangulations only reduces the induced charge, and use the constraints of Section II-A instead.) Imposing (4) on (5) gives the ECFIE of [19]. To write it in compact form, we introduce the operators

A:=2(Kk−iηSk),B:=−4(Tk−iηKk′).(6)A:=2(K_k-i\eta S_k),\qquad B:=-4(T_k-i\eta K_k'). \tag*{(6)}

By the jump relations (3), γ+Es=12(φ+Aφ)\gamma^+E^s=\frac{1}{2}(\varphi+A\varphi), and we write

ψ:=φ+Aφ=2γ+Es.(7)\psi:=\varphi+A\varphi=2\gamma^+E^s. \tag*{(7)}

With these definitions, the ECFIE reads

iη(Ptψ+Pνφ)+2Hψ−12PνBφ=−2(iηPt+2H)γ+Ei−2Pν∂νEi.(8)i\eta(P_t\psi+P_\nu\varphi)+2\mathcal{H}\psi-\frac{1}{2}P_\nu B\varphi =-2(i\eta P_t+2\mathcal{H})\gamma^+E^i-2P_\nu\partial_\nu E^i. \tag*{(8)}

Its normal part contains the hypersingular operator TkT_k through BB, so (8) is not of the second kind. The regularized ECFIE (R-ECFIE) of [19] applies the static single-layer operator S0S_0, that is, SkS_k with k=0k=0, as a Calderón regularizer to the normal part. The resulting second-kind equation is

Ptψ+S0Pν[Bφ−2iηφ−4Hψ]=−2Ptγ+Ei+4S0Pν[∂νEi+2Hγ+Ei].(9)P_t\psi+S_0P_\nu[B\varphi-2i\eta\varphi-4\mathcal{H}\psi] =-2P_t\gamma^+E^i+4S_0P_\nu[\partial_\nu E^i+2\mathcal{H}\gamma^+E^i]. \tag*{(9)}

Low Frequencies and the Constrained Formulation

Each Cartesian component of (5) is a radiating Helmholtz solution, so the ansatz also represents fields that are not divergence-free. The exact density gives a Maxwell field, but a discrete density need not. The far-field pattern FF of (5), defined by Es(x)∼eik∣x∣F(x^)/∣x∣E^s(x)\sim e^{ik\lvert x\rvert}F(\widehat{x})/\lvert x\rvert as ∣x∣→∞\lvert x\rvert\to\infty, with x^=x/∣x∣\widehat{x}=x/\lvert x\rvert on the unit sphere S2\mathbb{S}^{2}, is

F(x^)=14π∫Γe−ikx^⋅y(−ikx^⋅ν(y)−iη)φ(y) dsy.(10)F(\widehat{x})=\frac{1}{4\pi}\int_{\Gamma}e^{-ik\widehat{x}\cdot y}(-ik\widehat{x}\cdot\nu(y)-i\eta)\varphi(y)\,{\rm d}s_y. \tag*{(10)}

A true Maxwell far field is transverse, x^⋅F=0\widehat{x}\cdot F=0 [28], and ikx^⋅Fik\widehat{x}\cdot F is the far field of div⁡Es\operatorname{div}E^s.

Three defects of a discrete density dominate as k→0k\to0. First, away from the scatterer, the single-layer potential contributes the monopole term −iηeik∣x∣∫Γφ ds/(4π∣x∣)-i\eta e^{ik\lvert x\rvert}\int_{\Gamma}\varphi\,{\rm d}s/(4\pi\lvert x\rvert). Its coefficient vanishes for the exact density as k→0k\to0, but for a discrete density it is of the size of the discretization error and dominates the quasi-static field, which decays like ∣x∣−3\lvert x\rvert^{-3}. Taking η=k\eta=k, which mirrors the factor kk of the current term of the Stratton–Chu formula Es=−∇kSk[ν⋅γ+E]+ikZSk[J]E^s=-\nabla_k S_k[\nu\cdot\gamma^+E]+ikZ S_k[J] [28], with JJ the surface current, prevents JJ from being O(k)O(k). Second, with η=k\eta=k, constant densities become a near-nullspace: for k=η=0k=\eta=0 they produce no exterior field and are annihilated by the left-hand sides of (8) and (9). Third, the induced charge, proportional to

Q(φ)=∫Γν⋅γ+Es ds=12∫Γν⋅(φ+Aφ) ds,(11)Q(\varphi)=\int_{\Gamma}\nu\cdot\gamma^+E^s\,{\rm d}s=\frac{1}{2}\int_{\Gamma}\nu\cdot(\varphi+A\varphi)\,{\rm d}s, \tag*{(11)}

vanishes for the exact solution, since div⁡Ei=0\operatorname{div}E^i=0 in Ω\Omega and the conductor is uncharged, but not for a discrete density, and its Coulomb field, proportional to Qx/(4π∣x∣3)Q\boldsymbol{x}/(4\pi|\boldsymbol{x}|^3), decays like ∣x∣−2|\boldsymbol{x}|^{-2}, more slowly than the quasi-static field.

To address these issues, we therefore impose the following constraints:

bi(φ)=∫S2x^ix^⋅F(x^) dsx^=0,i∈{1,2,3},b_i(\varphi)=\int_{S^2}\widehat{x}_i\widehat{x}\cdot F(\widehat{x})\,\mathrm{d}s_{\widehat{x}}=0,\quad i\in\{1,2,3\},
b4(φ)=Q(φ)=0.(12)b_4(\varphi)=Q(\varphi)=0. \tag*{(12)}

The first three are the dipole moments of the far field of div⁡Es\operatorname{div}E^s. Both conditions hold for the exact solution at every frequency. Since ∫S2x^ix^j ds=4πδij/3\int_{S^2}\widehat{x}_i\widehat{x}_j\,\mathrm{d}s=4\pi\delta_{ij}/3, for η=k\eta=k the first three reduce to bi(φ)=−13∫Γφi ds+O(k2)b_i(\varphi)=-\frac{1}{3}\int_{\Gamma}\varphi_i\,\mathrm{d}s+O(k^2) as k→0k\to0. They thus remove both the ∣x∣−1|\boldsymbol{x}|^{-1} term and the constant near-nullspace, while b4b_4 removes the net charge.

We impose (12) with Lagrange multipliers, as is standard for constraints in Galerkin boundary element methods, for instance for the total charge in electrostatics [29]. Writing the R-ECFOIE (9) as Lφ=fL\varphi=f, we collect the functionals in b=(b1,…,b4)\boldsymbol{b}=(b_1,\ldots,b_4) and seek φ∈H1/2(Γ)3\varphi\in H^{1/2}(\Gamma)^3 and λ∈C4\boldsymbol{\lambda}\in\mathbb{C}^4 such that

⟨Lφ,v⟩+λ⋅b(v)=⟨f,v⟩for all v∈H1/2(Γ)3,\langle L\varphi,v\rangle+\boldsymbol{\lambda}\cdot\boldsymbol{b}(v)=\langle f,v\rangle\quad\text{for all }v\in H^{1/2}(\Gamma)^3,
b(φ)=0,(13)\boldsymbol{b}(\varphi)=0, \tag*{(13)}

with the bilinear pairing ⟨⋅,⋅⟩\langle\cdot,\cdot\rangle of Section III. The exact density solves (13) with λ=0\boldsymbol{\lambda}=0, so the constraints act only on the discrete solution. We take η=k\eta=k at all frequencies. The same construction applies to the ECFOIE (8), in different function spaces, but with η=k\eta=k it appears to be inaccurate at low frequency (Section IV-A), so for kD<1kD<1 we use the R-ECFOIE. The three defects above dominate the error only for kD≪1kD\ll1, with DD the diameter of Ω\Omega, and for kD≥1kD\ge1 the constraints are in general not needed. They remain consistent there, but they add four unnecessary unknowns to the linear system, so we do not impose them for kD≥1kD\ge1.

Galerkin Discretization

Let Γh\Gamma_h be a closed, consistently oriented, shape-regular polyhedral approximation of Γ\Gamma, with flat triangular faces Th\mathcal{T}_h and vertices {xa}a=1N\{x_a\}_{a=1}^N. We use νh\nu_h for its outward unit normal, which is constant on each face. The scalar trial and test space on Γh\Gamma_h is the continuous P1 space Vh=span⁡{ϕa}a=1N⊂C0(Γh)V_h=\operatorname{span}\{\phi_a\}_{a=1}^N\subset C^0(\Gamma_h). Each Cartesian component of the vector density is represented in VhV_h, giving 3N3N degrees of freedom. Throughout, ⟨u,v⟩Γ=∫Γu⋅v ds\langle u,v\rangle_\Gamma=\int_\Gamma u\cdot v\,\mathrm{d}s denotes the bilinear (unconjugated) pairing on a surface Γ\Gamma, with u⋅vu\cdot v the ordinary product for scalar functions. It is understood as a duality pairing when uu is less regular, and as ⟨μ,v⟩=∫v dμ\langle\mu,v\rangle=\int v\,\mathrm{d}\mu when u=μu=\mu is a measure on the surface. The subscript is omitted when the surface is clear. For a scalar boundary operator X∈{A,B,S0}X\in\{A,B,S_0\} constructed on Γh\Gamma_h, its corresponding Galerkin matrix XhX_h has entries

(Xh)ab=⟨Xϕb,ϕa⟩Γh.(14)(X_h)_{ab}=\langle X\phi_b,\phi_a\rangle_{\Gamma_h}. \tag*{(14)}

This gives the matrices AhA_h, BhB_h, and S0,hS_{0,h}, the first two each assembled in a single element-pair loop. For BB, which contains the hypersingular operator TkT_k, this is a duality pairing, evaluated through Mau's identity on Γh\Gamma_h [29]. The mass matrix,

(Mh)ab=∫Γhϕaϕb ds,(M_h)_{ab}=\int_{\Gamma_h}\phi_a\phi_b\,\mathrm{d}s,

is assembled using the exact element formula for affine triangles. As is standard in modern BEM codes, the singular integrals over touching triangles are evaluated with Sauter–Schwab transformations [25], and for the nearly singular integrals over nearby disjoint pairs the part (1−k2R2/2)/(4πR)(1-k^2R^2/2)/(4\pi R) of GkG_k, with R=∣x−y∣R=|x-y|, and its gradient are integrated analytically over the source triangle [30]. The near-field criterion and the quadrature orders follow the default BEAST Maxwell assembly [31], so that both codes in Section IV use the same rules. The operator matrices are compressed as hierarchical matrices with HMatrices.jl [32], using adaptive cross approximation with tolerance 10−610^{-6} and leaf size 64 unless stated otherwise.

Discrete ECFOIE and R-ECFOIE

The curvature terms in (8) and (9) act on ψ=φ+Aφ=2γ+Es\psi=\varphi+A\varphi=2\gamma^+E^s, which we approximate by a P1 vector function ψh∈Vh3\psi_h\in V_h^3. Write φi,a\varphi_{i,a}, i∈{1,2,3}i\in\{1,2,3\}, a∈{1,…,N}a\in\{1,\ldots,N\}, for the coefficient of the iith Cartesian component of φh\varphi_h at the vertex xax_a, and let φi=(φi,1,…,φi,N)T∈CN\varphi_i=(\varphi_{i,1},\ldots,\varphi_{i,N})^{\mathsf{T}}\in\mathbb{C}^N. The matrices AhA_h and BhB_h of Section III are mapped to P1 coefficients by mass solves, so that the coefficients of ψh\psi_h are

ψi:=φi+Mh−1Ahφi.(15)\psi_i:=\varphi_i+M_h^{-1}A_h\varphi_i. \tag*{(15)}

For a scalar N×NN\times N matrix XhX_h, we write Xh(3)=I3⊗XhX_h^{(3)}=I_3\otimes X_h, where ⊗\otimes denotes the Kronecker product. Thus, Xh(3)X_h^{(3)} is block diagonal with three copies of XhX_h and applies XhX_h to each Cartesian component. Let Pν,hP_{\nu,h} be the weak piecewise discretization of the normal projector Pν=ννTP_\nu=\nu\nu^{\mathsf{T}}, with entries

[Pν,h](i,a),(j,b)=∫Γhϕaϕb(νh)i(νh)j ds.(16)[P_{\nu,h}]_{(i,a),(j,b)}=\int_{\Gamma_h}\phi_a\phi_b(\nu_h)_i(\nu_h)_j\,\mathrm{d}s. \tag*{(16)}

The weak tangential projector is Pt,h=Mh(3)−Pν,hP_{t,h}=M_h^{(3)}-P_{\nu,h}. The weak approximation of PνBφP_\nu B\varphi is

rν:=Pν,h(Mh(3))−1Bh(3)φ.(17)r_\nu:=P_{\nu,h}(M_h^{(3)})^{-1}B_h^{(3)}\varphi. \tag*{(17)}

Below, the moment vector g∈C3N\boldsymbol{g}\in\mathbb{C}^{3N} of a vector field gg on Γh\Gamma_h has the entries [g](j,a)=∫Γhϕagj ds[\boldsymbol{g}]_{(j,a)}=\int_{\Gamma_h}\phi_ag_j\,\mathrm{d}s. It contains Galerkin moments rather than nodal values, and (Mh(3))−1g(M_h^{(3)})^{-1}\boldsymbol{g} gives the coefficients of the L2L^2 projection of gg onto Vh3V_h^3.

The curvature enters the scheme through two curvature matrices Hh(3),Hn,h∈C3N×3NH_h^{(3)},H_{n,h}\in\mathbb{C}^{3N\times3N} and two curvature moment vectors fH,fH,ν∈C3Nf_{\mathcal{H}},f_{\mathcal{H},\nu}\in\mathbb{C}^{3N}, constructed in Section III-B. The matrices represent in Galerkin form the multiplication operators u↦Huu\mapsto\mathcal{H}u and u↦PνHuu\mapsto P_\nu\mathcal{H}u, respectively, while the vectors contain the Galerkin moments of the corresponding incident-field terms HγEi\mathcal{H}\gamma E^i and PνHγEiP_\nu\mathcal{H}\gamma E^i. The discrete ECFOIE, i.e. the Galerkin counterpart of (8), is then

iη(Pt,hψ+Pν,hφ)+2Hh(3)ψ−12rν=−2iηft−2fν\mathrm{i}\eta(P_{t,h}\psi+P_{\nu,h}\varphi)+2H_h^{(3)}\psi-\frac{1}{2}r_\nu=-2\mathrm{i}\eta f_t-2f_\nu
−4fH.(18)\qquad\qquad\qquad\qquad\qquad\qquad\qquad\qquad-4f_{\mathcal{H}}. \tag*{(18)}

where ftf_t and fνf_\nu are the moment vectors of PtEiP_tE^i and Pν∂νEiP_\nu\partial_\nu E^i, respectively, with the facewise normal νh\nu_h computed with a high-order triangle rule. For the R-ECFOIE (9), define

μ:=−2iηPν,hφ+rν−4Hn,hψ.(19)\mu:=-2\mathrm{i}\eta P_{\nu,h}\varphi+r_\nu-4H_{n,h}\psi. \tag*{(19)}

We discretize the regularized normal block in the product form obtained directly from (9):

Pt,hψ+S0,h(3)(Mh(3))−1μ=−2ft+4S0,h(3)(Mh(3))−1(fν+2fH,ν),(20)P_{t,h}\psi+S_{0,h}^{(3)}(M_h^{(3)})^{-1}\mu = -2f_t+4S_{0,h}^{(3)}(M_h^{(3)})^{-1}(f_\nu+2f_{\mathcal{H},\nu}), \tag*{(20)}

with fH,νf_{\mathcal{H},\nu} from (24). A discretization through the Calderón identity −4S0T0=I−4K02-4S_0T_0=I-4K_0^2 [19 Thm. 5.8] gives nearly the same results but is up to twice as slow. As in [11, 33], S0S_0 may also be replaced by SκS_\kappa, κ=k+ik1/3\kappa=k+ik^{1/3}, which better regularizes TkT_k at high frequencies. Since for Im⁡κ>0\operatorname{Im}\kappa>0, SκS_\kappa is invertible, indeed coercive up to a rotation, and the R-ECFOIE remains of the second kind and uniquely solvable. We use SκS_\kappa only in Figure 2 and Table VI, since the low-frequency results rely on S0S_0.

Figure 2. Unit sphere, ten points per wavelength: GMRES iterations (solid, left axis) and εE\varepsilon_E (dashed, right axis) versus kk of the R-ECFOIE with the regularizers S0S_0 and SκS_\kappa, κ=k+ik1/3\kappa= k + \mathrm{i}k^{1/3}, and of the Calderón-preconditioned RWG EFIE.

Discrete Curvature

The curvature terms of (8) and (9) require H\mathcal{H} on Γh\Gamma_h, where it vanishes on each face and is concentrated on the edges. We recover it from the first variation of area [26, 27]. For a smooth surface and a vector field VV, with H=12div⁡Γν\mathcal{H}=\frac{1}{2}\operatorname{div}_{\Gamma}\nu, the derivative of the area of {x+tV(x)}\{x+tV(x)\} at t=0t=0 is

∫Γdiv⁡ΓV ds=∫Γ2Hν⋅V ds\int_{\Gamma}\operatorname{div}_{\Gamma}V\,\mathrm{d}s=\int_{\Gamma}2\mathcal{H}\nu\cdot V\,\mathrm{d}s

[28]. On Γh\Gamma_h, integrating by parts on each face leaves only edge terms, and the discrete counterpart of 2Hν2\mathcal{H}\nu is the edge measure [27]

∑e(me++me−)δe=2∑eheneδe,he:=sin⁡(θe/2),(21)\sum_e(m_e^++m_e^-)\delta_e=2\sum_e h_en_e\delta_e,\qquad h_e:=\sin(\theta_e/2), \tag*{(21)}

where me±m_e^{\pm} are the outward unit conormals of the two faces adjacent to the edge ee (Figure 1(a)), nen_e is the unit bisector of their normals, θe\theta_e is the fold angle, positive at convex edges, and δe\delta_e is the arclength measure on ee, so that ⟨δe,v⟩=∫ev dℓ\langle\delta_e,v\rangle=\int_e v\,\mathrm{d}\ell. The scalar curvature measure is then given by Hh=∑eheδe\mathcal{H}_h=\sum_e h_e\delta_e.

Figure 1. (a) Two flat faces Te±T_e^{\pm} sharing the edge ee, with outward normals νe±\nu_e^{\pm}, their unit bisector nen_e, and the outward conormals me±m_e^{\pm}. (b) Triangles incident to the vertex xax_a, whose edges e∋xae \ni x_a (thick) contribute to the nodal curvature Ha\mathcal{H}_a.

Concentrated on the edges, Hh\mathcal{H}_h would make the curvature terms act only on the edge traces of ψh∈Vh3\psi_h\in V_h^3. We instead average it over the vertex patches, which turns the singular edge measure into a P1 field compatible with the trial space and intended to recover the smooth curvature under refinement. Let Aa=∫Γhϕa dsA_a=\int_{\Gamma_h}\phi_a\,\mathrm{d}s be the area assigned to xax_a, a third of the area of the triangles incident to $x_a ({xref}Fig. 1(b)`). The nodal curvature and the P1 curvature field are then defined by

Ha:=⟨Hh,ϕa⟩Aa=12Aa∑e∋xaheLe\mathcal{H}_a:=\frac{\langle\mathcal{H}_h,\phi_a\rangle}{A_a}=\frac{1}{2A_a}\sum_{e\ni x_a}h_eL_e

and

Hh(1):=∑a=1NHaϕa∈Vh,(22)\mathcal{H}_h^{(1)}:=\sum_{a=1}^{N}\mathcal{H}_a\phi_a\in V_h, \tag*{(22)}

respectively, where the first sum runs over the edges ee incident to xax_a, LeL_e is the length of ee, and the factor 12\frac{1}{2} comes from ⟨δe,ϕa⟩=Le/2\langle\delta_e,\phi_a\rangle=L_e/2. Since the P1 basis functions satisfy ∑aϕa=1\sum_a\phi_a=1, the total curvature is unchanged, ∫ΓhHh(1) ds=⟨Hh,1⟩\int_{\Gamma_h}\mathcal{H}_h^{(1)}\,\mathrm{d}s=\langle\mathcal{H}_h,1\rangle. We then get that the curvature matrices are given by

[Hh]ab=∫ΓhHh(1)ϕaϕb ds,[H_h]_{ab}=\int_{\Gamma_h}\mathcal{H}_h^{(1)}\phi_a\phi_b\,\mathrm{d}s,
[Hn,h](i,a),(j,b)=∫ΓhHh(1)ϕaϕb(νh)i(νh)j ds,(23)[H_{n,h}]_{(i,a),(j,b)}=\int_{\Gamma_h}\mathcal{H}_h^{(1)}\phi_a\phi_b(\nu_h)_i(\nu_h)_j\,\mathrm{d}s, \tag*{(23)}

and Hh(3)\mathcal{H}_h^{(3)} acts on all three components. The integrands above are cubic polynomials on each face and are integrated exactly. The matrices Hh(3)H_h^{(3)} and Hn,hH_{n,h} discretize the multiplication operators ψ↦Hhψ\psi\mapsto\mathcal{H}_h\psi and ψ↦Pν,hHhψ\psi\mapsto P_{\nu,h}\mathcal{H}_h\psi, the latter with the facewise normal of the projector Pν,hP_{\nu,h}. The curvature term 2Hψ2\mathcal{H}\psi of the ECFOIE (8) thus becomes 2Hh(3)ψ2\mathcal{H}_h^{(3)}\psi, and the normal-block term −4PνHψ-4P_\nu\mathcal{H}\psi of the R-ECFOIE (9) becomes −4Hn,hψ-4H_{n,h}\psi. The incident field supplies the three corresponding moment vectors

[fH](j,a)=∫ΓhHh(1)ϕaEji ds,[f_{\mathcal{H}}]_{(j,a)}=\int_{\Gamma_h}\mathcal{H}_h^{(1)}\phi_aE_j^i\,\mathrm{d}s,
[fH,ν](j,a)=∫ΓhHh(1)ϕa(νh)j(νh⋅Ei) ds,(24)[f_{\mathcal{H},\nu}]_{(j,a)}=\int_{\Gamma_h}\mathcal{H}_h^{(1)}\phi_a(\nu_h)_j(\nu_h\cdot E^i)\,\mathrm{d}s, \tag*{(24)}

evaluated with the same face rule as the other incident-field moment vectors. The first enters the ECFOIE right-hand side as −4fH-4f_{\mathcal{H}}, and the second contributes 8S0,h(3)(Mh(3))−1fH,ν8S_{0,h}^{(3)}(M_h^{(3)})^{-1}f_{\mathcal{H},\nu} to the regularized right-hand side.

When the discrete normals converge, this edge measure converges in a weak sense to 2Hν2\mathcal{H}\nu [34].

Implementation of the Low-Frequency Constraints

The functionals (12) are evaluated on the basis of Vh3V_h^3, which gives a matrix Λh∈C4×3N\Lambda_h\in\mathbb{C}^{4\times3N} with entries [Λh]j,(i,a)=bj(ϕaei)[\Lambda_h]_{j,(i,a)}=b_j(\phi_a e_i). Each entry bj(ϕaei)b_j(\phi_a e_i) of a far-field row is a double integral, over Γh\Gamma_h in (10) and over S2S^2 in (12). Over Γh\Gamma_h we use the facewise normal νh\nu_h and the same triangle rule as for the incident-field moment vectors in (18). Over S2S^2 we use a standard product rule of sufficiently high degree. For the charge row, the discrete counterpart of (11) is Qh=12nhTψ=qh‾φQ_h=\frac{1}{2}n_h^T\psi=\overline{q_h}\varphi, with nhn_h the moment vector of νh\nu_h. Inserting (15) and using the symmetry of MhM_h gives the row vector, computed once,

qh=12(nh+(AhT)(3)(Mh(3))−1nh),(25)q_h=\frac{1}{2}\left(n_h+(A_h^T)^{(3)}(M_h^{(3)})^{-1}n_h\right), \tag*{(25)}

which is the fourth row of Λh\Lambda_h, that is, [Λh]4,(i,a)=[qh](i,a)[\Lambda_h]_{4,(i,a)}=[q_h]_{(i,a)}. Let Lhψ=fhL_h\psi=f_h denote the left-hand side of the regularized R-ECFOIE (20), with LhL_h the matrix of its left-hand side, in which ψ\psi and μ\mu depend linearly on φ\varphi, and fh=−2ft+4S0,h(3)(Mh(3))−1(fν+2fH,ν)f_h=-2f_t+4S_{0,h}^{(3)}(M_h^{(3)})^{-1}(f_\nu+2f_{\mathcal{H},\nu}). The Galerkin counterpart of (13) is the saddle-point system [29]

\begin{bmatrix} L_h & \Lambda_h^T\\ \Lambda_h & 0 \end{bmatrix} \begin{bmatrix} \varphi\\ \lambda \end{bmatrix} = \begin{bmatrix} f_h\\ 0 \end{bmatrix}. \tag*{(26)}\end{bmatrix}

in which ΛhT\Lambda_h^{\mathsf{T}} is the transpose, not the conjugate transpose, because the pairing is bilinear. As for the unconstrained equation, we precondition from the left with blockdiag⁡((Mh(3))−1,I4)\operatorname{blockdiag}((M_h^{(3)})^{-1},I_4). We also scale the constraints symmetrically, replacing Λh\Lambda_h by ΣΛh\Sigma\Lambda_h and ΛhT\Lambda_h^{\mathsf{T}} by ΛhTΣ\Lambda_h^{\mathsf{T}}\Sigma, with Σ=diag⁡(σ1,…,σ4)\Sigma=\operatorname{diag}(\sigma_1,\ldots,\sigma_4) and σj=N/∥(Mh(3))−1ΛhTej∥2\sigma_j=\sqrt{N}/\|(M_h^{(3)})^{-1}\Lambda_h^{\mathsf{T}}e_j\|_2, so that the columns of (Mh(3))−1ΛhTΣ(M_h^{(3)})^{-1}\Lambda_h^{\mathsf{T}}\Sigma have norm N\sqrt{N}. As noted after (12), the far-field rows are O(k)O(k) as k→0k\to0, and Σ\Sigma removes this factor. The preconditioned matrix is thus the second-kind operator (Mh(3))−1Lh(M_h^{(3)})^{-1}L_h augmented by four rows and columns that remain of comparable size as k→0k\to0, so its conditioning does not deteriorate. The system is solved by GMRES. Each iteration costs one application of LhL_h and O(N)O(N) operations for the four constraints.

Surface Current

In many applications, the surface current is itself a quantity of interest. The density φ\varphi is auxiliary, but the physical surface current J=ν×H+=(ikZ)−1ν×curl⁡E+\boldsymbol{J}=\nu\times\boldsymbol{H}^{+}=(ikZ)^{-1}\nu\times\operatorname{curl}\boldsymbol{E}^{+} can be recovered weakly from the traces of the solution. With Eν=ν⋅γ+E=ν⋅(γEi+12ψ)E_{\nu}=\nu\cdot\gamma^{+}E=\nu\cdot(\gamma E^{i}+\frac{1}{2}\psi) and g=∂ν+E=∂νEi−14Bφ+iη2φg=\partial_{\nu}^{+}E=\partial_{\nu}E^{i}-\frac{1}{4}B\varphi+\frac{i\eta}{2}\varphi, the identity ν×curl⁡E+=∇ΓEν−Ptg\nu\times\operatorname{curl}E^{+}=\nabla_{\Gamma}E_{\nu}-P_{t}g [19 Lemma 3.2] and integration by parts give, for tangential ww,

⟨J,w⟩=1ikZ[−⟨Eν,div⁡Γw⟩−⟨g,w⟩].(27)\langle J,w\rangle=\frac{1}{ikZ}\left[-\langle E_{\nu},\operatorname{div}_{\Gamma}w\rangle-\langle g,w\rangle\right]. \tag*{(27)}

Testing with lowest-order RWG functions gives JhJ_h from a sparse mass-matrix system, in which gg is replaced by its P1 approximation gh∈Vh3g_h\in V_h^{3}, obtained by one mass solve from Bh(3)φB_h^{(3)}\varphi and the moment vector of ∂νEi\partial_{\nu}E^{i}. The recovered current also permits a field evaluation through the Stratton–Chu formula [28], but with the constraints of § 2-A this is not needed at low frequency, and we evaluate all fields with (5).

Numerical Results

We consider the unit sphere, a Helmholtz resonator, surfaces of controlled regularity, a rounded Fichera cube, and a smoothed Stanford bunny, in order of increasing geometric difficulty. Unless stated otherwise, we solve the R-ECFOIE in the product form (20) with k=η=πk=\eta=\pi, for the unit plane wave Ei(x)=e1eikx3E^{i}(x)=e_1e^{ikx_3}, polarized along xx and propagating along +z+z. For kD<1kD<1 we add the constraints (12) and solve the saddle-point system (26). In all low-frequency tests we take D=10−8λD=10^{-8}\lambda, with λ=2π/k\lambda=2\pi/k, where the EFIE suffers from low-frequency breakdown [6]. As kD→0kD\to0, the scattered field converges, with relative error of order kDkD, to the electrostatic field of the uncharged conductor in the uniform field Ei(0)E^{i}(0) [35], which we use as the reference. For the unit sphere, this is the dipole field [3x^(x^⋅Ei(0))−Ei(0)]/∣x∣3[3\hat{x}(\hat{x}\cdot E^{i}(0))-E^{i}(0)]/|x|^{3}. For other geometries, we compute it from the Galerkin Laplace single-layer equation with zero total charge [29]. Errors are evaluated at 100 nearly uniformly distributed directions x^j∈S2\hat{x}_j\in\mathbb{S}^{2}, from a Fibonacci lattice: the scattered field EsE^{s} at the points dx^jd\hat{x}_j, with d=Dd=D, and the far-field pattern FF in (10) in the directions x^j\hat{x}_j. With ∥u∥=(∑j∣uj∣2)1/2\|u\|=(\sum_j|u_j|^2)^{1/2} and F⊥=(I−x^x^T)FF_{\perp}=(I-\hat{x}\hat{x}^{\mathsf{T}})F, we report

εE=∥Es−Es,ref∥∥Es,ref∥,εF=∥F⊥−F⊥ref∥∥F⊥ref∥,εL=∣x^⋅F∣∥F∥.(28)\varepsilon_E=\frac{\|E^{s}-E^{s,\mathrm{ref}}\|}{\|E^{s,\mathrm{ref}}\|},\qquad \varepsilon_F=\frac{\|F_{\perp}-F_{\perp}^{\mathrm{ref}}\|}{\|F_{\perp}^{\mathrm{ref}}\|},\qquad \varepsilon_L=\frac{|\hat{x}\cdot F|}{\|F\|}. \tag*{(28)}

where the superscript “ref” denotes a reference solution and εL\varepsilon_L, which needs none, measures the violation of far-field transversality. The references are the Mie series for the sphere at D=λD=\lambda, the electrostatic field described above at low frequency, and, for the other geometries at D=λD=\lambda and above, BEAST.jl EFIE solutions with RWG functions [31].

PEC Sphere

We first consider scattering of the default plane wave by the unit sphere with D=λD=\lambda, that is, k=η=πk=\eta=\pi. The reference is the Mie-series solution, with d=2d=2, and the meshes are listed in Table I. We solve the ECFOIE and the R-ECFOIE, each without and with the constraints (12), using the same assembled operators on each mesh, so that the differences are due to the formulations alone. Both are preconditioned by the inverse mass matrix and solved with un restarted GMRES, with relative tolerance 10−610^{-6} and at most 400 iterations.

hhNNR-ECFOIE withoutR-ECFOIE withECFOIE withoutECFOIE with
0.2502713.47 (24)3.43 (30)2.78 (61)2.76 (74)
0.1755081.73 (29)1.68 (29)1.44 (69)1.44 (85)
0.12510500.77 (24)0.75 (28)0.67 (75)0.66 (92)
0.10015780.50 (24)0.49 (28)0.44 (80)0.44 (99)
0.07031150.25 (23)0.24 (27)0.22 (93)0.22 (106)
0.05060640.12 (22)0.12 (26)0.11 (107)0.11 (117)
0.04095140.077 (22)0.074 (26)0.072 (119)0.071 (130)

Table 1. Sphere with D=λD=\lambda: Near-Field Error εE\varepsilon_E (%) and GMRES Iterations, Without and With the Constraints

Table I shows that the field errors decrease at second order in hh, that is, like N−1N^{-1} (fitted slopes 2.00–2.09 for h≤0.175h\le0.175). This rate is consistent with the O(h2)O(h^2) errors of both P1 interpolation and the flat-triangle approximation of Γ\Gamma. The two equations reach nearly the same accuracy, but the R-ECFOIE iteration count stays bounded under refinement, whereas that of the ECFOIE grows steadily. The constraints change the errors only slightly and add a few iterations, so at this frequency they are not needed, as noted in § 2-A. Without the curvature term (not shown), the errors of both equations stagnate at about 70% on all meshes.

To give an idea of the overall cost of the proposed formulations, we compare with the EFIE of BEAST.jl [31] on the same sphere, without the constraints, on meshes with N=3115N=3115 to 30966 vertices. Our formulations then have 3N3N unknowns and the EFIE has 3N−63N-6, one per edge. Both codes use the quadrature of Section II and unrestarted GMRES with tolerance 10−610^{-6}, Jacobi-preconditioned for the EFIE. All matrices are compressed, with HMatrices.jl for our formulations and FastBEAST.jl for the EFIE, and are also assembled densely up to N=9514N=9514. Each code uses the loosest compression that changes εE\varepsilon_E by less than 1%: ACA tolerance 10−310^{-3} and leaf size 128 for HMatrices.jl, and tolerance 10−410^{-4}, minimum box size 200, and maximum rank 50 for FastBEAST.jl. Times are medians of three runs on an Apple M3 Max with 10 threads.

NNMethodIt.H-matrix Assem.H-matrix SolveDense Assem.Dense SolveεE\varepsilon_E (%)
3115ECFOIE935.10.83.60.90.222
EFIE2405.02.74.43.50.199
R-ECFOIE238.70.47.40.30.247
6064ECFOIE10713.62.613.23.00.113
EFIE30012.58.617.615.80.100
R-ECFOIE2321.10.928.01.00.121
9514ECFOIE11926.84.832.77.20.0721
EFIE35320.419.945.643.10.0634
R-ECFOIE2239.51.471.02.40.0763
30966ECFOIE162123.119.5——0.0228
EFIE554108.4142.9——0.0192
R-ECFOIE22182.74.9——0.0224

Table 2. Sphere with D=λD = \lambda: comparison with the BEAST EFIE; times in seconds.

Table II shows that the three discretizations reach nearly the same accuracy on each mesh, with the EFIE slightly ahead, and that compression changes the errors only marginally. The iteration counts differ markedly. As expected, that of the EFIE grows steadily under refinement, that of the ECFOIE grows more slowly, and that of the R-ECFOIE stays constant, so the R-ECFOIE solve is the fastest on every mesh and its advantage grows with NN. Our assembly is more expensive, because it involves several scalar operators and, for the R-ECFOIE, the additional static single-layer operator of (20). Even so, with compression the ECFOIE has the lowest total time on every mesh, and the R-ECFOIE overtakes the EFIE as NN grows. Our formulations also need less memory: in dense form, the two scalar matrices AhA_h and BhB_h occupy less than a quarter of the memory of the EFIE matrix, and with compression the peak memory on the finest mesh is about 30% lower. These timings depend on the implementations and the tuning, but the iteration counts do not. The Jacobi-preconditioned EFIE is the most common RWG formulation. Since the EFIE is of the first kind, its iteration count grows under mesh refinement, so it is the natural reference for the unregularized ECFOIE. The natural reference for the R-ECFOIE is instead the Calderón-preconditioned EFIE [36], whose iteration count is likewise bounded under refinement. We compare the two over frequency below.

To study the dependence on the frequency, we solve the R-ECFOIE with S0S_0 and with SκS_\kappa for k=ηk = \eta from π\pi to 8π8\pi, that is, DD from λ\lambda to 8λ8\lambda, on meshes with ten points per wavelength, h=λ/10h = \lambda/10, and up to 24082 vertices. Figure 2 shows that with S0S_0 the iteration count grows from 24 to 62, whereas with SκS_\kappa it stays between 20 and 23. The errors are nearly the same for both regularizers, and they decrease with kk because the meshes also resolve the sphere better. For comparison, we solve the Calderón-preconditioned RWG EFIE [36] with Buffa–Christiansen dual functions [5] in BEAST.jl on the same

meshes. At k≤2.5πk \le2.5\pi, it needs fewer iterations and is slightly more accurate. Its iteration count, however, grows from 9 to 52 and exceeds that of the R-ECFOIE with SκS_\kappa from k=3πk = 3\pi on, where the accuracy of the two is nearly the same.

Next, to study the low-frequency behavior of our formulations, we take D=10−8λD = 10^{-8}\lambda for the same sphere, that is, k=η=π⋅10−8k = \eta= \pi\cdot10^{-8}, and solve the R-ECFOIE without and with the constraints (12), with the rest of the setup unchanged. The reference is the static dipole field described at the beginning of this section. Table III reports εE\varepsilon_E at the radii dd and 4d4d, the GMRES iterations, and the induced charge q=∣Qh∣/∣Γh∣q = \lvert Q_h\rvert/\lvert\Gamma_h\rvert, with QhQ_h the discrete counterpart of (11).

NNWithout constraints ddWithout constraints 4d4dWithout constraints It.Without constraints qqWith constraints ddWith constraints 4d4dWith constraints It.With constraints qq
83343.31369412⋅1002\cdot10^{0}10.0010.34173⋅10−63\cdot10^{-6}
271123.6453.6408⋅10−18\cdot10^{-1}2.8892.926142⋅10−62\cdot10^{-6}
1050219.8869.8421⋅1001\cdot10^{0}0.7060.708122⋅10−72\cdot10^{-7}
311514655862441⋅1011\cdot10^{1}0.2300.231126⋅10−86\cdot10^{-8}
951470.79280.9455⋅10−15\cdot10^{-1}0.0730.073112⋅10−82\cdot10^{-8}

Table 3. Sphere with D=10−8λD = 10^{-8}\lambda: R-ECFOIE near-field error εE\varepsilon_E (%) at radii dd and 4d4d, GMRES iterations, and induced charge q=∣Qh∣/∣Γh∣q = \lvert Q_h\rvert/\lvert\Gamma_h\rvert, without and with the constraints.

Without the constraints, the R-ECFOIE fails at this frequency. The errors are comparatively large, do not decrease under refinement, and grow with the distance to the scatterer, and the induced charge is of the order of the incident field. This is the behavior anticipated in § 2-A. In fact, with η=k\eta= k, the constant densities form a near-nullspace, the charge is not controlled, and its Coulomb field, proportional to Qhx/(4π∣x∣3)Q_h\boldsymbol{x}/(4\pi\lvert\boldsymbol{x}\rvert^3), decays more slowly than the exact dipole field. With the constraints, the charge vanishes to the solver tolerance, the errors decrease at second order and no longer depend on the distance, and GMRES needs fewer iterations, with a count that does not grow under refinement. With η=k\eta= k, the errors of the unregularized ECFOIE remain large with or without the constraints, likely because its first-kind normal part loses the term iηPνφ\mathrm{i}\eta\mathcal{P}_{\nu}\varphi as η→0\eta\to0, so we use the R-ECFOIE at low frequency.

Helmholtz Resonator

We next consider a smooth axisymmetric body with an open internal chamber, seen in cross-section in Figure 3, obtained by revolving a smooth profile curve, a cubic B-spline, about the zz axis. Its outer radius is 1.14, its height 2.45, and D≈2.56D \approx2.56, and a neck of radius 0.121 connects the mouth, at the top, to a chamber of radius 0.86, so that the boundary is a single smooth closed surface. Unless stated otherwise, the incident plane wave in this section is Ei(x)=e1e−ikx3E^{i}(x) = \mathbf{e}_{1}e^{-\mathrm{i}kx_{3}}, which enters the mouth along −z-z. The five meshes, with 4660 to 61860 vertices, are generated by Gmsh with a curvature-based size field.

Figure 3. Total field ∣E∣|E| on the plane y=0y = 0 for the Helmholtz resonator at k=19.5k = 19.5, where D≈8λD \approx8\lambda, for a plane wave incident at 20° from the −z-z axis in the plane y=0y = 0, with EiE^{i} in that plane. (a) Around the closed body, which produces a shadow below it. (b) Inside the cavity, where the gray band is the cut through the PEC wall.

We first take D=λD = \lambda and solve both equations without the constraints. The reference is a BEAST EFIE solution, compressed by FastBEAST.jl and solved with tolerance 10−810^{-8}, on the 31773-vertex mesh, and εE\varepsilon_{E} is evaluated with d=Dd = D.

*Mesh of the reference.

Table 4 shows the same behavior as for the sphere. Both equations converge at about second order until the errors reach the level of the reference, on the finest meshes, and the longitudinal fraction εL\varepsilon_L decreases in the same way. The R-ECFOIE iteration count is again independent of the mesh, whereas that of the ECFOIE grows under refinement and is already an order of magnitude larger, as is that of the EFIE.

NN\multicolumn{4}{c}{R-ECFOIE}\multicolumn{4}{c}{ECFOIE}
εE\varepsilon_EεF\varepsilon_FεL\varepsilon_LIt.εE\varepsilon_EεF\varepsilon_FεL\varepsilon_LIt.
46600.4300.4060.12370.3100.2850.11305
69920.2290.2150.068370.1730.1570.069302
156420.0840.0770.029370.0660.0570.032369
31773*0.0290.0250.014360.0300.0250.016442
618600.0180.0160.0069350.0260.0240.0088527

Table 4. Helmholtz resonator with D=λD = \lambda: near- and far-field errors and longitudinal fraction (%) and GMRES iterations against the BEAST EFIE.

At D=10−8λD = 10^{-8}\lambda, the reference is the electrostatic field computed on the 61860-vertex mesh. Table 5 confirms the observations made for the sphere, i.e., without the constraints the induced charge is not controlled and the errors are large and erratic, whereas with them the charge vanishes, the errors decrease at second order, and the iteration count is the same on all meshes.

NN\multicolumn{4}{c}{Without constraints}\multicolumn{4}{c}{With constraints}
DD4D4DIt.qqDD4D4DIt.qq
466015.9263.08757⋅10−27\cdot10^{-2}0.3770.495281⋅10−71\cdot10^{-7}
69921.6793.366773⋅10−33\cdot10^{-3}0.2060.327285⋅10−85\cdot10^{-8}
1564222.4990.09641⋅10−11\cdot10^{-1}0.0820.136287⋅10−87\cdot10^{-8}
31773123.7496.1825⋅10−15\cdot10^{-1}0.0330.066286⋅10−86\cdot10^{-8}

Table 5. Helmholtz resonator with D=10−8λD = 10^{-8}\lambda: R-ECFOIE near-field error εE\varepsilon_E (%) at radii DD and 4D4D, GMRES iterations, and induced charge qq, without and with the constraints.

At higher frequencies, the neck acts as a circular waveguide and above k≈15.2k \approx15.2 the plane wave enters the chamber. We locate resonances by scanning kk and monitoring the mean of ∣E∣2|E|^{2} at points inside the chamber, using the 15642-vertex mesh. Figure 3 shows the total field at the resonance k=19.5k = 19.5 on the plane y=0y = 0, for incidence at 20° from the −z-z axis in the plane y=0y = 0, with EiE^{i} in that plane. Inside, Figure 3(b), a standing wave fills the neck and the chamber, the oblique incidence breaks its axial symmetry, and the field reaches about 10 times the incident amplitude. Outside, Figure 3(a), the incident and reflected waves interfere at the cavity opening and the body produces a shadow below it. At these frequencies we do not attempt to produce an EFIE reference field, so we assess the solution with two quantities that vanish for an exact Maxwell field: the far-field longitudinal fraction εL\varepsilon_L and the divergence ratio ∥∇⋅Ehs∥/∥kEhs∥\lVert\nabla\cdot E^{s}_{h}\rVert/\lVert kE^{s}_{h}\rVert at the points inside the chamber. Both stay below 3×10−33\times10^{-3} over the frequency range 15.5≤k≤2015.5\leq k\leq20.

kk15.2515.5*18.75*19.2519.5*2019.5* (20°)
R-ECFOIE, S0S_0323542773647750943807
R-ECFOIE, SκS_\kappa168402610402500617631
Scalar CFIE5457143138128143149

Table 6. Helmholtz resonator, 15642 vertices: GMRES iterations of the R-ECFOIE and of the scalar combined-field equation (29); resonances marked *, incidence along −z-z, except at 20° in the last column.

To put the iteration counts in perspective, we also solve the scalar sound-soft problem for the plane wave ui=eikq^⋅xu^{i}=e^{\mathrm{i}k\widehat{\mathbf{q}}\cdot x} with q^=−e3\widehat{\mathbf{q}}=-\mathbf{e}_{3}, as for EiE^{i}, or tilted by 20° in the plane y=0y = 0 for the last column of Table VI, using the combined-field equation

(12I+Kk−iηSk)σ=−ui,η=k,(29)\left(\frac{1}{2}I+K_k-\mathrm{i}\eta S_k\right)\sigma=-u^{i}, \qquad\eta=k, \tag*{(29)}

for the density of us=(Dk−iηSk)σu^{s}=(D_k-\mathrm{i}\eta S_k)\sigma, discretized with the same P1 elements, mass-matrix preconditioner, and GMRES tolerance. Table VI shows that the resonator is hard already for this scalar problem, whose iteration count increases markedly once kk is well above the cutoff, as expected for boundary integral equations on geometries that trap waves [37]. The R-ECFOIE needs several times more iterations, and its count is higher at some of the electromagnetic resonances, which need not coincide with those of the scalar problem. With SκS_\kappa, the R-ECFOIE needs 21–48% fewer iterations, and its far field differs from that for S0S_0 by εF≤0.4%\varepsilon_F \leq0.4\% away from the resonances and by 0.8–5.7% at them. Resonances are sensitive to discretization errors, and the mesh has only about seven points per wavelength there.

Surfaces of Controlled Regularity

To see how the regularity of Γ\Gamma affects the convergence, we consider the surfaces {r(ω)ω:ω∈S2}\{r(\boldsymbol{\omega})\boldsymbol{\omega}:\boldsymbol{\omega}\in S^2\} with r=1+0.45∣ω3∣pr=1+0.45|\omega_3|^p or r=1.45−0.45∣ω3∣pr=1.45-0.45|\omega_3|^p, both with diameter D=2.9D=2.9. Their regularity at the equator ω3=0\omega_3=0 is controlled by pp: C∞C^\infty for p=2p=2, C2,0.6C^{2,0.6} for p=2.6p=2.6, C1,0.5C^{1,0.5} for p=1.5p=1.5, and Lipschitz for p=1p=1, with a mild edge along the equator. The edge is concave for the first family and convex for the second (insets of Figure 4). Near an edge with exterior opening angle Ω\Omega, the field behaves like dπ/Ω−1d^{\pi/\Omega-1}, with dd the distance to the edge [23]. It is therefore in H1H^1 at the concave edge, with Ω≈132∘\Omega\approx132^\circ, but not at the convex one, with Ω≈215∘\Omega\approx215^\circ. We solve for the default plane wave with k=η=πk=\eta=\pi, that is, D=1.45λD=1.45\lambda, and compare the far field with BEAST EFIE solutions on meshes with h=0.031h=0.031, which differ from those with h=0.044h=0.044 by at most 0.04%0.04\%. We mesh the surfaces quasi-uniformly, with hh from 0.250.25 to 0.0440.044 and the equator made of mesh edges.

Figure 4. Surfaces r(ω)ωr(\boldsymbol{\omega})\boldsymbol{\omega} with r=1+0.45∣ω3∣pr=1+0.45|\omega_3|^p (left, concave edge for p=1p=1) and r=1.45−0.45∣ω3∣pr=1.45-0.45|\omega_3|^p (right, convex edge for p=1p=1) at k=η=πk=\eta=\pi: far-field error εF\varepsilon_F of the R-ECFOIE versus the mesh size hh, for p=2p=2, 2.62.6, 1.51.5, and 11, which give the regularity in the legend. The insets show the cross-sections of the surfaces. The reference error is about 0.04%0.04\%.

Figure 4 shows that εF\varepsilon_F decreases with an approximate slope of 2 on all surfaces down to C1,0.5C^{1,0.5}, even though the curvature of the C1,0.5C^{1,0.5} surfaces is unbounded at the equator. On the Lipschitz surface with the concave edge, the error still converges, but more slowly, with a fitted slope of 1.7 over all meshes. On the Lipschitz surface with the convex edge, it stagnates at 3.9%, and εL\varepsilon_L stays at 0.035 on all meshes. The computed field is thus not a Maxwell field. The iteration count is between 27 and 37 in all cases. Thus, reduced surface regularity does not affect the convergence down to C1,0.5C^{1,0.5}, and a concave edge, at which the field remains in H1H^1, only slows it. At a convex edge, where the field is not in H1H^1, the method fails, as anticipated in § 1.

Rounded Fichera Cube

The rounded Fichera cube, Figure 5, is the cube (−1,1)3(-1,1)^3 with the positive octant [0,1)3[0,1)^3 removed and all resulting edges rounded with fillet radius ρ=0.1\rho=0.1, so that D≈3.32D\approx3.32. Since the fillets meet the faces tangentially, the surface is C1,1C^{1,1}: its normal is continuous, but its curvature jumps from 0 on the faces to 1/ρ=101/\rho=10 on the fillets. It thus falls outside the C2,αC^{2,\alpha} setting of [19], but it has no edges and is smoother than the C1,0.5C^{1,0.5} surfaces of Section IV-C, on which the errors still decrease at about second order. The Gmsh meshes, with 974 to 73994 vertices, are refined near the fillets according to the curvature. They are generated independently, so they are not nested, and their refinement near the fillets varies from mesh to mesh.

Figure 5. Fichera cube with D=2λD = 2\lambda, incidence along +z+z with EiE^{i} along xx: ∣J∣/∣Hi∣|J|/|H^{i}| on the rounded cube from the R-ECFOIE on the 7247-vertex mesh, recovered as in § 3-D, and on the sharp cube from the BEAST EFIE on a uniform 6938-vertex mesh, on a common scale from 0 to 3, clipped above.

We first take D=2λD=2\lambda, that is, k=η=4π/D≈3.79k=\eta=4\pi/D\approx3.79, and solve both equations without the constraints. The reference is a dense BEAST EFIE solution on a separately generated 2216-vertex mesh, which agrees to within 0.5% in the far field with BEAST solutions on two other meshes.

NN\multicolumn{4}{c}{R-ECFOIE}\multicolumn{4}{c}{ECFOIE}
εE\varepsilon_EεF\varepsilon_FεL\varepsilon_LIt.εE\varepsilon_EεF\varepsilon_FεL\varepsilon_LIt.
97417.6414.919.075913.0511.056.55215
156912.9611.086.33639.928.424.90250
24868.547.354.01675.624.722.85288
32068.747.424.28686.085.073.15308
50945.504.682.64713.703.091.89388
72473.833.261.84732.582.161.32427
129752.121.781.06731.391.150.74512
258871.140.950.59740.830.690.44623
488090.640.540.31730.540.480.23740

Table 7. Rounded Fichera Cube with D=2λD=2\lambda: Near- and far-field errors and longitudinal fraction (%) and GMRES iterations against the BEAST EFIE

Table VII shows that all errors and the longitudinal fraction decrease under refinement at about second order on the finer meshes, until the errors reach the level of the reference, and that the R-ECFOIE iteration count stays nearly constant. The ECFOIE is somewhat more accurate but needs four to ten times more iterations.

On the finest mesh, the recovered surface current differs from that of the BEAST EFIE on the same mesh by 2.5% in the relative L2L^2 norm of ∣J∣|J| on the flat faces and by 4.9% overall, with the largest differences on the fillets. Figure 5 compares it with the EFIE current on the sharp cube. The two agree away from the edges, and on the lit face z=−1z=-1 both are close to the physical-optics value 2∣Hi∣2|H^i|. At the edges, the current on the sharp cube concentrates in narrow lines, where it is singular, whereas the fillets spread it over a band.

At D=10−8λD=10^{-8}\lambda we use incidence along −x-x with EiE^i along yy, and on each mesh the reference is the electrostatic field computed on that mesh. Table VIII shows the same behavior as for the sphere and the resonator, without and with the constraints, and with them GMRES needs about half as many iterations. On four finer meshes, solved only with the constraints, the errors continue to decrease at about second order in the mesh size, to below 1% at radius dd, with the same iteration count. The errors are nonetheless much larger than for the sphere and the Helmholtz resonator at comparable NN, which shows that in both regimes the accuracy is limited by the resolution of the fillets. These results hold for the fillet radius ρ=0.1\rho= 0.1, and they do not extend to the sharp cube, whose edges the method does not handle.

NNWithout constraints ddWithout constraints 4d4dWithout constraints It.Without constraints qqWith constraints ddWith constraints 4d4dWith constraints It.With constraints qq
97480.80291.5773⋅10−13 \cdot10^{-1}29.8138.14428⋅10−68 \cdot10^{-6}
156921.7648.39802⋅10−22 \cdot10^{-2}22.0926.76445⋅10−65 \cdot10^{-6}
248627.84105.8831⋅10−11 \cdot10^{-1}15.3618.53461⋅10−51 \cdot10^{-5}
320614.3726.72822⋅10−22 \cdot10^{-2}15.8419.80462⋅10−52 \cdot10^{-5}
50948.63920.25845⋅10−35 \cdot10^{-3}10.2814.03486⋅10−66 \cdot10^{-6}
72479.27232.84873⋅10−23 \cdot10^{-2}7.49510.86483⋅10−63 \cdot10^{-6}
12975————4.3826.875494⋅10−64 \cdot10^{-6}
25887————2.4933.606493⋅10−63 \cdot10^{-6}
48089————1.3371.879502⋅10−62 \cdot10^{-6}
73994————0.9101.322502⋅10−62 \cdot10^{-6}

Table VIII. Rounded Fichera cube with D=10−8λD = 10^{-8}\lambda: R-ECFOIE near-field error εE\varepsilon_E (%) at radii dd and 4d4d, GMRES iterations, and induced charge qq, without and with the constraints.

Smoothed Stanford Bunny

Our last example is the Stanford bunny, a scanned geometry with strongly curved features. The scanned surface is not smooth: its triangulation has sharp folds at the ears and the base, which persist under refinement and act like the convex edge of Section IV-C, where the R-ECFOIE fails. We therefore use a smoothed bunny, Figure 6, of diameter D=2D = 2, defined as a level set of the indicator function of the scan smoothed by Gaussian convolution. We remesh it with Gmsh and project the vertices onto the level set by Newton’s method, so that refinement approximates the smooth surface. We then solve

Figure 6. Smoothed bunny at k=η=4πk = \eta= 4\pi, incidence along +x+x, R-ECFOIE and BEAST EFIE on the same 9210-vertex mesh. Top: ∣J∣/∣Hi∣|J|/|H^{i}| for EiE^{i} along yy, recovered as in § 3-D for the R-ECFOIE, seen from the lit side (−x-x) and the shadow side, on a common scale from 0 to 4, clipped above. Bottom: bistatic RCS in the horizontal plane. Forward scattering is at φ=0\varphi= 0.

the problem of scattering of a plane wave propagating along +x+x, with EiE^{i} along yy or along zz.

At k=η=2πk = \eta= 2\pi, against a BEAST EFIE reference on a separate 9104-vertex mesh, εF\varepsilon_F decreases from 24.7% and 22.0% for EiE^{i} along yy and zz, respectively, on a 2289-vertex mesh to 7.1% and 6.1% on a 15624-vertex mesh. At k=η=4πk = \eta= 4\pi, where the bunny is four wavelengths across, we solve on a mesh with 9210 vertices and h≤λ/10=0.05h \leq\lambda/10 = 0.05, and compare with the BEAST EFIE on the same mesh in Figure 6. The two surface currents show the same standing-wave pattern, and their magnitudes ∣J∣|J| differ by 4.7% in the relative L2L^{2} norm, most at the tip of the upright ear. The far fields differ by εF=4.0%\varepsilon_F = 4.0\% and 3.7% for the two polarizations, and the R-ECFOIE needs 129 GMRES iterations.

Discussion and Conclusion

We developed a continuous P1 Galerkin BEM for the electric field-only PEC formulation on flat triangular meshes, with a vertex-averaged curvature, Calderón regularization, and Lagrange-multiplier constraints for low frequencies. The errors decrease at about second order, also at D=10−8λD = 10^{-8}\lambda, and the R-ECFOIE iteration count does not grow under refinement. On the rounded Fichera cube and the smoothed bunny, the far fields and surface currents agree with EFIE solutions.

The method is intended for smooth or rounded scatterers. This restriction comes from the formulation, which requires fields in H1H^1, and not from the discretization: the errors still decrease at about second order on C1,αC^{1,\alpha} surfaces, but they stagnate on Lipschitz surfaces with convex edges. Open problems include a convergence analysis of the scheme, with a consistency estimate for the averaged curvature, and preconditioning near resonances.

Acknowledgment

Claude (Anthropic) helped translate the first author’s BEM code from Fortran 90 to Julia, implement geometry-specific features, and polish the text.

References

  1. [1]J. L. Volakis and K. Sertel, Integral Equation Methods for Electromagnetics. SciTech Publishing, 2012.DOI
  2. [2]S. M. Rao, D. R. Wilton, and A. W. Glisson, “Electromagnetic scattering by surfaces of arbitrary shape,” IEEE Transactions on Antennas and Propagation, vol. 30, no. 3, pp. 409–418, 1982.
  3. [3]M. Bebendorf, “Approximation of boundary element matrices,” Numerische Mathematik, vol. 86, no. 4, pp. 565–589, 2000.DOI
  4. [4]A. Buffa and R. Hiptmair, “Galerkin boundary element methods for electromagnetic scattering,” in Topics in Computational Wave Propagation: Direct and Inverse Problems, ser. Lecture Notes in Computational Science and Engineering, M. Ainsworth, P. Davies, D. Duncan, P. Martin, and B. Rynne, Eds. Berlin, Germany: Springer, 2003, vol. 31, pp. 83–124.DOI
  5. [5]A. Buffa and S. H. Christiansen, “A dual finite element complex on the barycentric refinement,” Mathematics of Computation, vol. 76, no. 260, pp. 1743–1769, 2007.
  6. [6]J.-S. Zhao and W. C. Chew, “Integral equation solution of Maxwell’s equations from zero frequency to microwave frequencies,” IEEE Transactions on Antennas and Propagation, vol. 48, no. 10, pp. 1635–1645, 2000.DOI
  7. [7]A. Merlini, A. Dély, K. Cools, and F. P. Andriulli, “Electromagnetic modelling at arbitrarily low frequency via the quasi-Helmholtz projectors,” in Advances in Mathematical Methods for Electromagnetics, K. Kobayashi and P. D. Smith, Eds. Institution of Engineering and Technology, 2020, pp. 381–415.DOI
  8. [8]M. Taskinen and P. Ylä-Oijala, “Current and charge integral equation formulation,” IEEE Transactions on Antennas and Propagation, vol. 54, pp. 58–67, 2006.DOI
  9. [9]C. L. Epstein and L. Greengard, “Debye sources and the numerical solution of the time harmonic Maxwell equations,” Communications on Pure and Applied Mathematics, vol. 63, pp. 413–463, 2010.
  10. [10]M. Ganesh and S. C. Hawkins, “A spectrally accurate algorithm for electromagnetic scattering in three dimensions,” Numerical Algorithms, vol. 43, pp. 25–60, 2006.DOI
  11. [11]O. Bruno, T. Elling, R. Paffenroth, and C. Turc, “Electromagnetic integral equations requiring small numbers of Krylov-subspace iterations,” Journal of Computational Physics, vol. 228, pp. 6169–6183, 2009.DOI
  12. [14]O. Bruno, R. Forman, R. Molavi, and C. Sideris, “High-order-accurate continuity enforcing Nyström discretization of 3D Maxwell combined field integral equations,” 2026.
  13. [15]E. Klaseboer, Q. Sun, and D. Y. C. Chan, “Nonsingular field-only surface integral equations for electromagnetic scattering,” IEEE Transactions on Antennas and Propagation, vol. 65, no. 2, pp. 972–977, 2017.DOI
  14. [17]L. M. Faria, C. Pérez-Arancibia, and C. Turc, “Combined field-only boundary integral equations for PEC electromagnetic scattering problem in spherical geometries,” SIAM Journal on Applied Mathematics, vol. 84, pp. 19–38, 2024.arxiv.org/abs/2303.14494
  15. [18]A. J. Yuffa and J. Markkanen, “A 3-D tensorial integral formulation of scattering containing intriguing relations,” IEEE Transactions on Antennas and Propagation, vol. 66, pp. 5274–5281, 2018.DOI
  16. [19]J. Burbano-Gallegos, C. Pérez-Arancibia, and C. Turc, “Maxwell à la Helmholtz: Electromagnetic scattering by 3D perfect electric conductors via Helmholtz integral operators,” ESAIM: Mathematical Modelling and Numerical Analysis, vol. 60, no. 1, pp. 273–315, 2026.
  17. [20]C. Pérez-Arancibia and C. Turc, “Maxwell à la Helmholtz: Direct boundary integral equations for 3D scattering by perfect electric conductors via Helmholtz operators,” arXiv:2605.01670, 2026.
  18. [21]L. M. Faria, C. Pérez-Arancibia, and M. Bonnet, “General-purpose kernel regularization of boundary integral equations via density interpolation,” Computer Methods in Applied Mechanics and Engineering, vol. 378, p. 113703, 2021.DOI
  19. [22]C. Geuzaine and J.-F. Remacle, “Gmsh: A three-dimensional finite element mesh generator with built-in pre- and post-processing facilities,” International Journal for Numerical Methods in Engineering, vol. 79, no. 11, pp. 1309–1331, 2009.
  20. [23]M. Costabel and M. Dauge, “Singularities of electromagnetic fields in polyhedral domains,” Archive for Rational Mechanics and Analysis, vol. 151, no. 3, pp. 221–276, 2000.DOI
  21. [24]A.-S. Bonnet-Ben Dhia, C. Hazard, and S. Löhnergel, “A singular field method for the solution of Maxwell’s equations in polyhedral domains,” SIAM Journal on Applied Mathematics, vol. 59, no. 6, pp. 2028–2044, 1999.
  22. [25]S. A. Sauter and C. Schwab, Boundary Element Methods, ser. Springer Series in Computational Mathematics. Berlin, Germany: Springer, 2011, vol. 39.
  23. [26]M. Meyer, M. Desbrun, P. Schröder, and A. H. Barr, “Discrete differential-geometry operators for triangulated 2-manifolds,” in Visual-ization and Mathematics III, H.-C. Hege and K. Polthier, Eds. Berlin: Springer, 2003, pp. 35–57.DOI
  24. [27]J. M. Sullivan, “Curvatures of smooth and discrete surfaces,” in Discrete Differential Geometry, ser. Oberwolfach Seminars. Birkhäuser, 2008, vol. 38, see also arXiv:0710.4497.arxiv.org/abs/0710.4497
  25. [28]D. Colton and R. Kress, Integral Equation Methods in Scattering Theory. Philadelphia, PA: SIAM, 2013, reprint of the 1983 Wiley edition.DOI
  26. [29]O. Steinbach, Numerical Approximation Methods for Elliptic Boundary Value Problems: Finite and Boundary Elements. New York: Springer, 2008.
  27. [30]D. R. Wilton, S. M. Rao, A. W. Glisson, D. H. Schaubert, O. M. Al-Bundak, and C. M. Butler, “Potential integrals for uniform and linear source distributions on polygonal and polyhedral domains,” IEEE Transactions on Antennas and Propagation, vol. 32, no. 3, pp. 276–281, 1984.DOI
  28. [31]BEAST.jl contributors, “BEAST.jl: Boundary element analysis and simulation toolkit,” https://github.com/mkroos/BEAST.jl, 2026.
  29. [32]IntegralEquations contributors, “HMatrices.jl: Hierarchical matrices for julia,” https://github.com/IntegralEquations/HMatrices.jl, 2026.
  30. [33]Y. Boubech and C. Turc, “Wave-number estimates for regularized combined field boundary integral operators in acoustic scattering problems with Neumann boundary conditions,” IMA J. Numer. Anal., vol. 33, no. 4, pp. 1176–1225, 2013.
  31. [34]K. Hildebrandt, K. Polthier, and M. Wardetzky, “On the convergence of metric and geometric properties of polyhedral surfaces,” Geometriae Dedicata, vol. 123, pp. 89–112, 2006.DOI
  32. [35]G. Dassios and R. Kleinman, Low Frequency Scattering, ser. Oxford Mathematical Monographs. Oxford: Clarendon Press, 2000.
  33. [36]F. P. Andriulli, K. Cools, H. Bagci, F. Olyslager, A. Buffa, S. Christiansen, and E. Michielsen, “A multiplicative Calderón preconditioner for the electric field integral equation,” IEEE Transactions on Antennas and Propagation, vol. 56, pp. 2398–2412, 2008.
  34. [37]P. Marchand, J. Galkowski, A. Spence, and E. A. Spence, “Applying GMRES to the Helmholtz equation with strong trapping: how does the number of iterations depend on the frequency?” Advances in Computational Mathematics, vol. 48, no. 4, p. 37, 2022.

Paper details

vlnc:W_ddbdm553
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 11

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Mathematics

Claude

View statement
Looking for related papers…
Contents