betaFeedback

WorksAgricultural and Biological Sciences

Automated discovery of interpretable hyperelastic material models for human brain tissue with EUCLID

Abstract

We propose an automated computational algorithm for simultaneous model selection and parameter identification for the hyperelastic mechanical characterization of human brain tissue. Following the motive of the recently proposed computational framework EUCLID (Efficient Unsupervised Constitutive Law Identitication and Discovery) and in contrast to conventional parameter calibration methods, we construct an extensive set of candidate hyperelastic models, i.e., a model library including popular models known from the literature, and develop a computational strategy for automatically selecting a model from the library that conforms to the available experimental data while being represented as an interpretable symbolic mathematical expression. This computational strategy comprises sparse regression, i.e., a regression problem that is regularized by a sparsity promoting penalty term that filters out irrelevant models from the model library, and a clustering method for grouping together highly correlated and thus redundant features in the model library. The model selection procedure is driven by labelled data pairs stemming from mechanical tests under different deformation modes, i.e., uniaxial compression/tension and simple torsion, and can thus be interpreted as a supervised counterpart to the originally proposed EUCLID that is informed by full-field displacement data and global reaction forces. The proposed method is verified on synthetical data with artificial noise and validated on experimental data acquired through mechanical tests of human brain specimens, proving that the method is capable of discovering hyperelastic models that exhibit both high fitting accuracy to the data as well as concise and thus interpretable mathematical representations.

Introduction

Despite extensive research over the past decades, the characterization of the mechanical response of biological tissues like those of the human brain remains an active field with many open questions, see the review article by Budday et al. [7]. The amount of data is usually limited by ethical restrictions and by the availability of only few specimens with short durability [12]. The general objective is therefore to leverage these limited data in an efficient manner to discover an adequate mathematical description of the tissue response. The conventional strategy is to a priori assume a constitutive model and to calibrate the tunable model parameters by means of the experimental measurements. However, the a priori choice of the constitutive model is driven by human experience and intuition; thus, this classical strategy is highly susceptible to introducing modeling errors that lead to poor fitting accuracy and/or the need for tedious and time-consuming iterative model correction procedures. Data-driven methods and machine learning approaches promise a powerful remedy. In this work, one of such methods, which falls under the umbrella of methods denoted as EUCLID (Efficient Unsupervised Constitutive Law Identification and Discovery) ([14]), is used for automatically discovering symbolic expressions of hyperelastic material models for human brain tissue based on experimental measurements.

The general idea behind machine-learning-based material modeling is to choose a model ansatz that exhibits a high expressiveness owing to a vast amount of tunable parameters, and to calibrate these parameters by leveraging the available data. Popular examples of versatile machine-learning-based material models include neural networks ([21]), splines ([42]), Gaussian processes ([18]), and neural ordinary differential equations ([43]). In the context of hyperelasticity, these methods can be used to learn the characteristic strain energy density function while special attention needs to be attributed to not violating physical constraints like objectivity or (poly-)convexity of the strain energy density function (As’ad et al., 2022; Klein et al., 2022a,b; Kalina et al., 2022; Thakolkaran et al., 2022; Chen and Guilleminot, 2022; Linka and Kuhl, 2022; As’ad and Farhat, 2022; Tac et al., 2022). Until now, the majority of the proposed machine learning models for hyperelasticity are informed by artificially generated data, e.g., data generated through simulations at the microscopic level. An exception is for example the work by Linka et al. [34], who train neural networks based on real experimental data for the characterization of human brain tissue. In contrast to machine-learning-based approaches stand model-free data-driven methods ([30, 26]), which seek to avoid the formulation of a material model altogether by solving forward problems that are directly informed by the data.

Both the previously mentioned machine-learning-based approaches as well as model-free data-driven methods have in common that the constitutive behavior is encoded in a black box that does not allow for physical interpretation, e.g., it is difficult to interpret the meaning of the many functions and parameters that compose models encoded in machine learning tools like neural networks. Furthermore, these methods typically rely on a vast amount of labeled data pairs that are not available under experimental conditions. The recognition of these issues motivated the development of the EUCLID method, which aims to discover interpretable symbolic expressions of material models using only experimentally available data like displacement fields and global reaction forces. Initially applied to hyperelasticity ([14, 27]) (see also the related and independent work by Wang et al. [46]), the framework was later extended to viscoelasticity ([36]), elastoplasticity ([15]), and generalized standard materials ([16]), see Flaschel [13] for an overview. Recently, discovering symbolic expressions for material models is gaining more and more attention in the field, see, e.g., the works by Bomarito et al. [4]; Kabliman et al. [28]; Park and Cho [39]; Abdusalаmov et al. (2023); Meyer and Ekre [37].

In this work, EUCLID is used to automatically discover hyperelastic strain energy density functions for describing the mechanical behavior of human brain tissue. The idea is to construct a set of candidate material models called the model library, which can be assembled for example from the vast available literature on hyperelastic material models (see the non-comprehensive list of reviewing articles by Boyce and Arruda [5]; Marckmann and Verron [35]; Steinmann et al. (2012); Dal et al. [10]; He et al. (2021)), and to use a specifically designed algorithm, based on sparse regression and feature clustering, to select from the library a material model which is encoded by an interpretable, simple mathematical expression and which is able to well capture the mechanical behavior observed in the experimental data. Due to the wet and shiny surface of brain tissues, displacement field data are difficult to acquire; thus, against the original philosophy of EUCLID ([13]), the method in this paper is not informed by full-field displacement and global reaction force data. Instead, we rely here on labeled data pairs stemming from uniaxial compression/tension and simple torsion tests of human brain tissue specimens.

The paper is organized as follows: In § 2, we construct the model library in which EUCLID searches for a suitable material model. In § 2, the proposed algorithm for model selection is discussed in detail. Subsequently, the method is tested on artificial data and actual experimental data in § 4 and § 5, respectively, and conclusions are drawn in § 6.

Notation: Tensors and matrices may appear in compact or index notation, e.g., F\mathbf{F} or FijF_{ij}, respectively. In compact notation, first-order tensors (vectors) and second-order tensors are denoted by bold letters, e.g., F\mathbf{F}. The transpose of a tensor is denoted by FT\mathbf{F}^{T}. When appearing in index notation, the order of the tensor equals the number of the indices. If not stated otherwise, the Einstein convention for summation over repeated indices is used in equations appearing in index notation, e.g., aibi=∑iaibia_i b_i = \sum_i a_i b_i. Inner products are denoted by ⋅\cdot, e.g., a⋅b=aibi\boldsymbol{a} \cdot\boldsymbol{b} = a_i b_i, and outer products by ⊗\otimes, e.g., {a⊗b}ij=aibj\{ \boldsymbol{a} \otimes\boldsymbol{b} \}_{ij} = a_i b_j. If no operation is indicated between two tensors, the juxtaposition implies tensor contraction, e.g., {FTF}ij=FkiFkj\{ \mathbf{F}^{T}\mathbf{F} \}_{ij} = F_{ki}F_{kj}. The trace of a tensor is denoted by tr⁡(□)\operatorname{tr}(\square), e.g., tr⁡(C)=Cii\operatorname{tr}(\mathbf{C}) = C_{ii}, the volumetric part by vol⁡(□)\operatorname{vol}(\square), the deviatoric part by dev⁡(□)\operatorname{dev}(\square), and the determinant by det⁡(□)\det(\square).

Model library

Strain energy density

The constitutive response of a hyperelastic material is completely characterized by the material strain energy density function. In the spirit of EUCLID, we construct a material model library, i.e., a large set of potential candidate material models, by introducing a general parametric ansatz for the unknown strain energy density. Under the assumption of incompressibility, the strain energy density WW of a hyperelastic material is postulated as Holzapfel, [25]

W=W~(F)−p⋅(J−1),(1)W = \widetilde{W}(\mathbf{F}) - p \cdot(J - 1), \tag*{(1)}

where F\mathbf{F} is the deformation gradient, pp is a scalar Lagrange multiplier that can be physically interpreted as the hydrostatic (or volumetric) pressure, and J=det⁡F=1J = \det\mathbf{F} = 1 is the determinant of the deformation gradient. A sufficient condition to satisfy the objectivity requirement for the material model is that WW depends on F\mathbf{F} through the right Cauchy-Green tensor C=FTF\mathbf{C} = \mathbf{F}^{T}\mathbf{F}, i.e. W~(F)=W^(C)\widetilde{W}(\mathbf{F}) = \widehat{W}(\mathbf{C}). Assuming furthermore isotropic material behavior, the contribution W^\widehat{W} can be expressed as a function of the invariants of C\mathbf{C}, defined as I1=tr⁡(C)I_1 = \operatorname{tr}(\mathbf{C}), I2=12(tr⁡2(C)−tr⁡(C2))I_2 = \frac{1}{2}(\operatorname{tr}^{2}(\mathbf{C}) - \operatorname{tr}(\mathbf{C}^{2})) and I3=det⁡(C)I_3 = \det(\mathbf{C}). An equally objective possibility for isotropic hyperelasticity is to express the strain energy density as a function of the principal stretches λ1\lambda_1, λ2\lambda_2, λ3\lambda_3 defined as the eigenvalues of the right stretch tensor U\mathbf{U}, which in turn is defined through the polar decomposition F=RU\mathbf{F} = \mathbf{R}\mathbf{U} Holzapfel, [25]. As we seek to avoid a priori assumptions on the material response, we do not limit ourselves to a strain energy density that depends solely on the strain invariants or solely on the principal stretches, but instead consider the general case in which the strain energy density includes a contribution W~I\widetilde{W}_I that depends on the strain invariants and a contribution W~λ\widetilde{W}_{\lambda} that depends on the principal stretches

W=W~I(I1,I2,I3)+W~λ(λ1,λ2,λ3)−p⋅(J−1).(2)W = \widetilde{W}_I(I_1, I_2, I_3) + \widetilde{W}_{\lambda}(\lambda_1, \lambda_2, \lambda_3) - p \cdot(J - 1). \tag*{(2)}

By doing so, we obtain a highly general expression for the strain energy density that encompasses many well-known hyperelastic constitutive models e.g. of the Mooney-Rivlin or Ogden types.

To introduce a general parametric ansatz for W~I\widetilde{W}_I, we assume that it can be expressed as a linear combination of a priori chosen nonlinear feature functions

W~I(I1,I2,I3)=θI⋅QI(I1,I2,I3),(3)\widetilde{W}_I(I_1, I_2, I_3) = \boldsymbol{\theta}_I \cdot\mathbf{Q}_I(I_1, I_2, I_3), \tag*{(3)}

where the nonlinear feature functions have been collected in the vector QI\mathbf{Q}_I and θI\boldsymbol{\theta}_I is a vector of unknown real-valued material parameters. We construct the feature vector QI\mathbf{Q}_I such that it contains features of the generalized Mooney-Rivlin model Rivlin, [40] and a logarithmic feature as it appears in the Gent-Thomas model Gent and Thomas, [20]

QI(I1,I2,I3)=[(I1−3)m(I2−3)n−m: n∈{1,…,NMooney}, m∈{0,…,n}⏟generalized Mooney-Rivlin features]T⊕[log⁡(I2/3)]⏟logarithmic feature,(4)\mathbf{Q}_I(I_1, I_2, I_3) = \left[ \underbrace{ (I_1 - 3)^m (I_2 - 3)^{n-m} :\ n \in\{1,\ldots,N_{\mathrm{Mooney}}\},\ m \in\{0,\ldots,n\} }_{\text{generalized Mooney-Rivlin features}} \right]^T \oplus \underbrace{\left[\log(I_2/3)\right]}_{\text{logarithmic feature}}, \tag*{(4)}

where ⊕\oplus denotes vector concatenation and the choice of NMooneyN_{\mathrm{Mooney}} dictates the size of the feature vector. This selection of feature functions was proven in Flaschel et al. [14] to have a high approximation power. We choose NMooney=3N_{\mathrm{Mooney}} = 3 in this work, such that θI\boldsymbol{\theta}_I comprises 10 unknown parameters.

To obtain a general parametric ansatz for the principal stretch dependent contribution W~λ\widetilde{W}_{\lambda}, we consider the generalized Ogden model Ogden, [38]

W~λ(λ1,λ2,λ3)=∑i=1NOgden2μiαi2(λ1αi+λ2αi+λ3αi−3).(5)\widetilde{W}_{\lambda}(\lambda_1,\lambda_2,\lambda_3) = \sum_{i=1}^{N_{\mathrm{Ogden}}} \frac{2\mu_i}{\alpha_i^2} \left(\lambda_1^{\alpha_i} + \lambda_2^{\alpha_i} + \lambda_3^{\alpha_i} - 3\right). \tag*{(5)}

where μi\mu_i and αi\alpha_i are unknown real-valued material parameters and NOgdenN_{\mathrm{Ogden}} is the number of considered terms in the generalized Ogden model. In contrast to the model library chosen in Eq. (3), the strain energy density of the generalized Ogden model depends nonlinearly on the unknown material parameters. In general, this complicates the inference of the material parameters from experimental measurements. Therefore, we assume in the following an a priori fixed set of NOgdenN_{\mathrm{Ogden}} distinct values of αi\alpha_i. By choosing NOgdenN_{\mathrm{Ogden}} sufficiently large, it is expected that this assumption does not significantly restrict the versatility of the model library. In this work, we choose NOgden=2⋅104N_{\mathrm{Ogden}} = 2 \cdot10^{4} values of αi\alpha_i evenly distributed between −100-100 and 100100 excluding zero, i.e., αi∈{−100,−99.99,…,−0.01,0.01,…,99.99,100}\alpha_i \in\{-100, -99.99, \ldots, -0.01, 0.01, \ldots, 99.99, 100\}. With this assumption, μi\mu_i remain the only unknowns in the model ansatz for W~λ\widetilde{W}_{\lambda} which can now be written as a linear combination of nonlinear feature functions

W~λ(λ1,λ2,λ3)=θλ⋅Qλ(λ1,λ2,λ3),(6)\widetilde{W}_{\lambda}(\lambda_1,\lambda_2,\lambda_3) = \boldsymbol{\theta}_{\lambda} \cdot\mathbf{Q}_{\lambda}(\lambda_1,\lambda_2,\lambda_3), \tag*{(6)}

where the nonlinear feature functions have been collected in the vector Qλ\mathbf{Q}_{\lambda} with components

{Qλ(λ1,λ2,λ3)}i=λ1αi+λ2αi+λ3αi−3,(7)\{\mathbf{Q}_{\lambda}(\lambda_1,\lambda_2,\lambda_3)\}_i = \lambda_1^{\alpha_i} + \lambda_2^{\alpha_i} + \lambda_3^{\alpha_i} - 3, \tag*{(7)}

and θλ\boldsymbol{\theta}_{\lambda} is a vector of unknown real-valued material parameters that are related to the parameters μi\mu_i through {θλ}i=2μi/αi2\{\boldsymbol{\theta}_{\lambda}\}_i = 2\mu_i/\alpha_i^2.

By defining

θ=[θIθλ],Q=[QI(I1,I2,I3)Qλ(λ1,λ2,λ3)],(8)\boldsymbol{\theta} = \begin{bmatrix} \boldsymbol{\theta}_I \\ \boldsymbol{\theta}_{\lambda} \end{bmatrix}, \qquad \mathbf{Q} = \begin{bmatrix} \mathbf{Q}_I(I_1,I_2,I_3) \\ \mathbf{Q}_{\lambda}(\lambda_1,\lambda_2,\lambda_3) \end{bmatrix}, \tag*{(8)}

the model library for the strain energy density can be written as

W=θ⋅Q−p⋅(J−1).(9)W = \boldsymbol{\theta} \cdot\mathbf{Q} - p \cdot(J - 1). \tag*{(9)}

To ensure that the strain energy density describes physically meaningful material behavior, we assume that θi≥0\theta_i \ge0 for all ii. The non-negativity of the material parameters is a sufficient (but not necessary) requirement for stability, see [22].

Stress-strain relation

After having defined the strain energy density, a bijective relation between the kinematic state and the stress state of the material is obtained through its differentiation. Specifically, the Piola stress P\mathbf{P} is computed by differentiating WW with respect to the deformation gradient

P=∂W∂F=∂W~∂F−pF−T,(10)\mathbf{P} = \frac{\partial W}{\partial\mathbf{F}} = \frac{\partial\widetilde{W}}{\partial\mathbf{F}} - p\mathbf{F}^{-T}, \tag*{(10)}

where we used ∂J∂F=JF−T\frac{\partial J}{\partial\mathbf{F}} = J\mathbf{F}^{-T}. Noting that W~=θ⋅Q=θI⋅QI+θλ⋅Qλ\widetilde{W} = \boldsymbol{\theta} \cdot\mathbf{Q} = \boldsymbol{\theta}_I \cdot\mathbf{Q}_I + \boldsymbol{\theta}_{\lambda} \cdot\mathbf{Q}_{\lambda}, we apply the chain rule to obtain

∂W~∂Fij=θI⋅(∂QI∂Ia∂Ia∂Fij)+θλ⋅(∂Qλ∂λb∂λb∂Fij).(11)\frac{\partial\widetilde{W}}{\partial F_{ij}} = \boldsymbol{\theta}_I \cdot\left(\frac{\partial\mathbf{Q}_I}{\partial I_a}\frac{\partial I_a}{\partial F_{ij}}\right) + \boldsymbol{\theta}_{\lambda} \cdot\left(\frac{\partial\mathbf{Q}_{\lambda}}{\partial\lambda_b}\frac{\partial\lambda_b}{\partial F_{ij}}\right). \tag*{(11)}

The derivatives of the strain invariants and of the principal stretches are provided in Appendix § 7.§ 1 and Appendix § 7.§ 2, respectively. The derivatives of the feature vectors follow in Appendix § 7.3. The Cauchy stress T\mathbf{T} is calculated from the Piola stress as T=PFT\mathbf{T} = \mathbf{P}\mathbf{F}^{T}.

Uniaxial compression and tension

Experimental measurements of specimens under uniaxial compression and tension deliver labeled data pairs in the form (uUT,F)(u_{\mathrm{UT},F)}, where uUTu_{\mathrm{UT}} is the longitudinal displacement at the displacement controlled end of the specimen and FF is the resulting force. Data pairs of the form (λUT,P11)(\lambda_{\mathrm{UT}},P_{11}), where λUT\lambda_{\mathrm{UT}} is the longitudinal stretch applied to the specimen and P11P_{11} is the longitudinal normal component of the Piola stress, are obtained through

λUT=uUT+hh,P11=Fπrout2,(12)\lambda_{\mathrm{UT}} = \frac{u_{\mathrm{UT}} + h}{h}, \qquad P_{11} = \frac{F}{\pi r_{\mathrm{out}}^{2}}, \tag*{(12)}

where hh and routr_{\mathrm{out}} are the height and the outer radius of the undeformed specimen, respectively. The previously introduced material model library can be used to derive a relation P11(λUT;θ)P_{11}(\lambda_{\mathrm{UT}};\boldsymbol{\theta}) that links the experimental inputs λUT\lambda_{\mathrm{UT}} and outputs P11P_{11} depending on the material parameters θ\boldsymbol{\theta}.

Applying a longitudinal stretch λUT\lambda_{\mathrm{UT}} to the specimen implies that F11=λUTF_{11}=\lambda_{\mathrm{UT}} and, due to symmetry, F22=F33F_{22}=F_{33}. As a result of the incompressibility assumption det⁡F=!1\det\mathbf{F}\overset{!}{=}1, the deformation gradient under uniaxial compression/tension must hence be

FUT=[λUT0001λUT0001λUT].(13)\mathbf{F}_{\mathrm{UT}}= \begin{bmatrix} \lambda_{\mathrm{UT}} & 0 & 0 \\ 0 & \frac{1}{\sqrt{\lambda_{\mathrm{UT}}}} & 0 \\ 0 & 0 & \frac{1}{\sqrt{\lambda_{\mathrm{UT}}}} \end{bmatrix}. \tag*{(13)}

The kinematic state is thus completely determined by the applied longitudinal stretch.

To obtain the relationship P11(λUT;θ)P_{11}(\lambda_{\mathrm{UT}};\boldsymbol{\theta}), the unknown hydrostatic pressure pp in Eq. (10) needs to be computed. As the material is allowed to freely deform in the x2x_2 and x3x_3 directions, it is P22=P33=!0P_{22}=P_{33}\overset{!}{=}0. This condition is used along with Eq. (10)

P33=∂W~∂F33−pF33−1=!0,(14)P_{33}=\frac{\partial\widetilde{W}}{\partial F_{33}}-pF_{33}^{-1}\overset{!}{=}0, \tag*{(14)}

to find the hydrostatic pressure

p=∂W~∂F33F33.(15)p=\frac{\partial\widetilde{W}}{\partial F_{33}}F_{33}. \tag*{(15)}

We hence obtain the desired relationship by substituting the pressure in Eq. (10)

P11(λUT;θ)=∂W~∂F11−pF11−1=∂W~∂F11−F33F11∂W~∂F33=θ⋅(∂Q∂F11−F33F11∂Q∂F33),(16)P_{11}(\lambda_{\mathrm{UT}};\boldsymbol{\theta})=\frac{\partial\widetilde{W}}{\partial F_{11}}-pF_{11}^{-1}=\frac{\partial\widetilde{W}}{\partial F_{11}}-\frac{F_{33}}{F_{11}}\frac{\partial\widetilde{W}}{\partial F_{33}}=\boldsymbol{\theta}\cdot\left(\frac{\partial\mathbf{Q}}{\partial F_{11}}-\frac{F_{33}}{F_{11}}\frac{\partial\mathbf{Q}}{\partial F_{33}}\right), \tag*{(16)}

where we denoted all the terms that depend on the longitudinal stretch as QUT′(λUT)\mathbf{Q}'_{\mathrm{UT}}(\lambda_{\mathrm{UT}}). This can be interpreted as a feature function derivative vector whose scalar product with the material parameters computes the longitudinal normal component of the Piola stress. More information for computing QUT′(λUT)\mathbf{Q}'_{\mathrm{UT}}(\lambda_{\mathrm{UT}}) is provided in Appendix § 7.§ 4.

Simple torsion

Now we consider a cylindrical specimen in a cylindrical coordinate system (r,ϑ,z)(r,\vartheta,z), where rr is the radial coordinate, ϑ\vartheta is the polar angle, and zz is the longitudinal coordinate. Assuming the specimen to undergo simple torsion around the zz-axis, experimental measurements on specimens under simple torsion deliver labeled data pairs in the form (ϕ,M)(\phi,M), where ϕ\phi is the applied angle of deformation at the sheared end of the specimen and MM is the resulting torque. The twist ψ\psi of the specimen can be deduced from the applied angle of deformation through ψ=ϕ/h\psi=\phi/h. The twist is transformed into data pairs of the form (ψ~,τ)(\widetilde{\psi},\tau), where ψ~=routψ\widetilde{\psi}=r_{\mathrm{out}}\psi and τ=M/rout3\tau=M/r_{\mathrm{out}}^3 are respectively a normalized twist and normalized torque.

After normalizing the radial coordinate through ρ=r/rout\rho=r/r_{\mathrm{out}}, the deformation gradient in the cylindrical coordinate system then reads [22]

FST=[FrrFrϑFrzFϑrFϑϑFϑzFzrFzϑFzz]=[100010001][10001ρψ~001].(17)\mathbf{F}_{\mathrm{ST}}= \begin{bmatrix} F_{rr} & F_{r\vartheta} & F_{rz} \\ F_{\vartheta r} & F_{\vartheta\vartheta} & F_{\vartheta z} \\ F_{zr} & F_{z\vartheta} & F_{zz} \end{bmatrix} = \begin{bmatrix} 1 & 0 & 0 \\ 0 & 1 & 0 \\ 0 & 0 & 1 \end{bmatrix} \begin{bmatrix} 1 & 0 & 0 \\ 0 & 1 & \rho\widetilde{\psi} \\ 0 & 0 & 1 \end{bmatrix}. \tag*{(17)}

The material model library can be used to derive a relation τ(ψ~;θ)\tau(\widetilde{\psi};\boldsymbol{\theta}) that links the experimental inputs ψ~\widetilde{\psi} and outputs τ\tau depending on the material parameters θ\boldsymbol{\theta}.

The normalized torque is given by

τ=∫012πρ2Tϑz dρ,(18)\tau=\int_{0}^{1}2\pi\rho^2T_{\vartheta z}\,d\rho, \tag*{(18)}

where the component of the Cauchy stress TϑzT_{\vartheta z} is, due to Eq. (17),

Tϑz=PϑiFzi=Pϑz.(19)T_{\vartheta z}=P_{\vartheta i}F_{zi}=P_{\vartheta z}. \tag*{(19)}

With reference to Eq. (10), we notice that there is no hydrostatic pressure contribution to PϑzP_{\vartheta z} under simple torsion, such that

Tϑz=∂W∂Fϑz=∂W~∂Fϑz=θ⋅∂Q∂Fϑz.(20)T_{\vartheta z}=\frac{\partial W}{\partial F_{\vartheta z}}=\frac{\partial\widetilde{W}}{\partial F_{\vartheta z}}=\boldsymbol{\theta}\cdot\frac{\partial Q}{\partial F_{\vartheta z}}. \tag*{(20)}

We finally obtain the desired relationship τ(ψ~;θ)\tau(\widetilde{\psi};\boldsymbol{\theta}) by substituting Eq. (20) in Eq. (18)

τ(ψ~;θ)=θ⋅∫012πρ2∂Q∂Fϑz dρ⏟QST′(ψ~).(21)\tau(\widetilde{\psi};\boldsymbol{\theta})=\boldsymbol{\theta}\cdot\underbrace{\int_{0}^{1}2\pi\rho^{2}\frac{\partial Q}{\partial F_{\vartheta z}}\,\mathrm{d}\rho}_{Q'_{\mathrm{ST}}(\widetilde{\psi})}. \tag*{(21)}

where we denoted all the terms that depend on the twist as QST(ψ~)′Q'_{\mathrm{ST}(\widetilde{\psi})}. This can be interpreted as a feature function derivative vector whose scalar product with the material parameters computes the normalized torque. More information for computing QST(ψ~)′Q'_{\mathrm{ST}(\widetilde{\psi})} is provided in Appendix § 7.§ 5.

Model discovery

After having defined the material model library, i.e., a versatile ansatz for the hyperelastic strain energy density, we seek an optimal choice of the material model parameters θ\boldsymbol{\theta}. Specifically, in the spirit of EUCLID - see Flaschel et al. [14] - we seek a parameter vector θ\boldsymbol{\theta} which leads at the same time to a small mismatch between the material model predictions and the experimental measurements, and to a simple discovered material model, i.e. one with a small number of terms. Unlike in the original work on EUCLID Flaschel et al., [14], in which the model selection was driven by a physics-informed optimization problem that was fed by fully unlabelled data, in this paper, labelled data pairs (i.e., stress versus strain data pairs under uniaxial compression/tension, and twist versus torque data pairs under simple torsion) are available to drive the model selection. Thus, the method proposed here can be interpreted as a supervised counterpart to the originally proposed EUCLID. The proposed algorithm for inferring θ\boldsymbol{\theta} is described in the following and a step-by-step overview is provided in Appendix § 8, see Fig. B.10.

Model-data mismatch

First, a quantitative measure of the mismatch between the material model predictions and the experimental measurements needs to be introduced. In the case of uniaxial compression/tension, the measurements are provided in the form of pairs (λUT(l),P11(l))(\lambda_{\mathrm{UT}}^{(l)},P_{11}^{(l)}) for a number of load steps l=1,…,nUTl=1,\ldots,n_{\mathrm{UT}}. Eq. (16) provides a mapping between the input and output data, thus leading to nUTn_{\mathrm{UT}} equations

P11(λUT(l);θ)=P11(l).(22)P_{11}(\lambda_{\mathrm{UT}}^{(l)};\boldsymbol{\theta})=P_{11}^{(l)}. \tag*{(22)}

Noting that each of the equations above depends linearly on θ\boldsymbol{\theta}, we write them as a linear system of equations

AUTθ=bUT.(23)\mathbf{A}_{\mathrm{UT}}\boldsymbol{\theta}=\mathbf{b}_{\mathrm{UT}}. \tag*{(23)}

with

AUT=[(QUT′(λUT(1)))T⋮(QUT′(λUT(nUT)))T],bUT=[P11(1)⋮P11(nUT)].(24)\mathbf{A}_{\mathrm{UT}}= \begin{bmatrix} \left(Q'_{\mathrm{UT}}(\lambda_{\mathrm{UT}}^{(1)})\right)^{T}\\ \vdots\\ \left(Q'_{\mathrm{UT}}(\lambda_{\mathrm{UT}}^{(n_{\mathrm{UT}})})\right)^{T} \end{bmatrix}, \qquad \mathbf{b}_{\mathrm{UT}}= \begin{bmatrix} P_{11}^{(1)}\\ \vdots\\ P_{11}^{(n_{\mathrm{UT}})} \end{bmatrix}. \tag*{(24)}

Analogously, in the case of simple torsion, the measurements are provided in the form of pairs (ψ~(l),τ(l))(\widetilde{\psi}^{(l)},\tau^{(l)}) for a number of load steps l=1,…,nSTl=1,\ldots,n_{\mathrm{ST}}. Eq. (21) provides a mapping between the input and output data, thus leading to nSTn_{\mathrm{ST}} equations

τ(ψ~(l);θ)=τ(l).(25)\tau(\widetilde{\psi}^{(l)};\boldsymbol{\theta})=\tau^{(l)}. \tag*{(25)}

which can be expressed once again as a linear system of equations

ASTθ=bST,(26)\mathbf{A}_{\mathrm{ST}}\boldsymbol{\theta}=\mathbf{b}_{\mathrm{ST}}, \tag*{(26)}

with

AST=[(QST′(ψ~(1)))T⋮(QST′(ψ~(nST)))T],bST=[τ(1)⋮τ(nST)].(27)\mathbf{A}_{\mathrm{ST}}=\begin{bmatrix}\left(Q'_{\mathrm{ST}}(\tilde{\psi}^{(1)})\right)^{T}\\ \vdots\\ \left(Q'_{\mathrm{ST}}(\tilde{\psi}^{(n_{\mathrm{ST}})})\right)^{T}\end{bmatrix},\qquad\mathbf{b}_{\mathrm{ST}}=\begin{bmatrix}\tau^{(1)}\\ \vdots\\ \tau^{(n_{\mathrm{ST}})}\end{bmatrix}. \tag*{(27)}

The linear systems in Eq. (23) and Eq. (26) are concatenated to the system Aθ=b\mathbf{A}\boldsymbol{\theta}=\mathbf{b} with

A=[rUTAUTrSTAST],b=[rUTbUTrSTbST],(28)\mathbf{A}=\begin{bmatrix}r_{\mathrm{UT}}\mathbf{A}_{\mathrm{UT}}\\ r_{\mathrm{ST}}\mathbf{A}_{\mathrm{ST}}\end{bmatrix},\qquad\mathbf{b}=\begin{bmatrix}r_{\mathrm{UT}}\mathbf{b}_{\mathrm{UT}}\\ r_{\mathrm{ST}}\mathbf{b}_{\mathrm{ST}}\end{bmatrix}, \tag*{(28)}

where rUT>0r_{\mathrm{UT}}>0 and rST>0r_{\mathrm{ST}}>0 scale the contributions of the uniaxial compression/tension data and the simple torsion data, respectively. During the experimental investigations conducted in the context of this work (see, e.g., § 5), the chosen range of applied deformation in uniaxial compression/tension and simple torsion led to measurements bUT\mathbf{b}_{\mathrm{UT}} and bST\mathbf{b}_{\mathrm{ST}}, respectively, that were different in magnitude. Choosing rUT=0.3r_{\mathrm{UT}=0.3} and rST=1r_{\mathrm{ST}}=1 was found to result in a proper scaling of the contributions from uniaxial compression/tension and simple torsion, leading to similar maximum absolute entries in the scaled measurements rUTbUTr_{\mathrm{UT}}\mathbf{b}_{\mathrm{UT}} and rSTbSTr_{\mathrm{ST}}\mathbf{b}_{\mathrm{ST}}. Finally, the total mismatch between the material model prediction and the experimental measurements is quantified by computing the mean squared error MSE of the residuals of the linear system of equations

MSE⁡(θ)=1nUT+nST∥Aθ−b∥22.(29)\operatorname{MSE}(\boldsymbol{\theta})=\frac{1}{n_{\mathrm{UT}}+n_{\mathrm{ST}}}\lVert\mathbf{A}\boldsymbol{\theta}-\mathbf{b}\rVert_{2}^{2}. \tag*{(29)}

Feature scaling

To obtain a system of equations with dimensionless parameters and system coefficients, we standardize the system of equations. Defining the mean and standard deviation of a vector x∈Rn\mathbf{x}\in\mathbb{R}^{n} as

Mean⁡(x)=1n∑ixi,Std⁡(x)=1n∑i(xi−Mean⁡(x))2,(30)\operatorname{Mean}(\mathbf{x})=\frac{1}{n}\sum_i x_i,\qquad\operatorname{Std}(\mathbf{x})=\sqrt{\frac{1}{n}\sum_i\left(x_i-\operatorname{Mean}(\mathbf{x})\right)^2}, \tag*{(30)}

the standardized system of equations reads

Aˉθˉ=bˉ(31)\bar{\mathbf{A}}\bar{\boldsymbol{\theta}}=\bar{\mathbf{b}} \tag*{(31)}

with

Aˉij=AijStd⁡(Aj),bˉi=biStd⁡(b),θˉj=Std⁡(Aj)Std⁡(b)θj,(32)\bar{A}_{ij}=\frac{A_{ij}}{\operatorname{Std}(A_j)},\qquad\bar{b}_i=\frac{b_i}{\operatorname{Std}(\mathbf{b})},\qquad\bar{\theta}_j=\frac{\operatorname{Std}(A_j)}{\operatorname{Std}(\mathbf{b})}\theta_j, \tag*{(32)}

where we defined AjA_j as the jthj^{\mathrm{th}} column of A\mathbf{A}. The mean squared error of the residuals of the standardized linear system of equations is defined as

MSE⁡‾(θˉ)=1nUT+nST∥Aˉθˉ−bˉ∥22.(33)\overline{\operatorname{MSE}}(\bar{\boldsymbol{\theta}})=\frac{1}{n_{\mathrm{UT}}+n_{\mathrm{ST}}}\lVert\bar{\mathbf{A}}\bar{\boldsymbol{\theta}}-\bar{\mathbf{b}}\rVert_{2}^{2}. \tag*{(33)}

Optimization problem

Our objectives are to calibrate the unknown material parameters such that the material model is in agreement with the experimental data, and to discard those terms in the model ansatz which have a minor influence on the fitting accuracy by setting their corresponding parameters to zero. To this end, we solve an L1L_1-regularized optimization problem (also denoted as sparse regression problem) of the form

θˉopt=arg min⁡θˉ≥0(12MSE⁡‾(θˉ)+λp∥θˉ∥1),(34)\bar{\boldsymbol{\theta}}^{\mathrm{opt}}=\underset{\bar{\boldsymbol{\theta}}\geq0}{\operatorname{arg\,min}}\left(\frac{1}{2}\overline{\operatorname{MSE}}(\bar{\boldsymbol{\theta}})+\lambda_p\lVert\bar{\boldsymbol{\theta}}\rVert_1\right), \tag*{(34)}

where MSE‾(θˉ)\overline{\mathrm{MSE}}(\bar{\theta}) is the previously introduced mean squared error function that quantifies the mismatch between the material model predictions and the experimental data, and ∥θˉ∥1=∑i∣θˉi∣\lVert\bar{\theta}\rVert_1 = \sum_i |\bar{\theta}_i| is an L1L_1-regularization term, also denoted as Lasso (least absolute shrinkage and selection operator). This term, first used for model selection by Frank and Friedman [17] and Tibshirani [45] and later applied to problems in dynamics by Brunton et al. [6], can be interpreted as a convex approximation of an operator that counts the number of nonzero entries in the material parameter vector. Thus, adding the L1L_1-regularization term to the minimization problem promotes sparsity of the material parameter vector. In previous works ([14, 15]), the more general LpL_p-regularization term ∥θˉ∥pp=∑i∣θˉi∣p\lVert\bar{\theta}\rVert_p^p = \sum_i |\bar{\theta}_i|^p with 0<p≤10 < p \le1 was adopted to promote sparsity in the solution vector. The LpL_p term has the advantage that it converges to the operator that counts the number of nonzero entries in the material parameter vector as pp approaches zero. Thus, it can be considered as a better measure of sparsity than the L1L_1-regularization term. However, the LpL_p term is non-convex for p<1p < 1; this implies that the optimization problem becomes non-convex and thus multiple solutions are to be expected, corresponding to local minima of the objective function. In our previous papers ([14, 15]), this issue was addressed by solving the optimization problem multiple times and selecting the minimum of the computed local minima, which obviously increases the computational complexity and cost of the minimization problem. In this work, we rely on the L1L_1 regularization term and thus solve a convex minimization problem which thus admits a unique solution. The influence of the regularization is governed by the choice of the weighting factor λp≥0\lambda_p \ge0. As proposed in [15, 16, 36], an appropriate choice of λp\lambda_p for striking a balance between fitting accuracy and mathematical complexity of the material model is obtained through a Pareto analysis (see § 3.5).

Solver

To solve the problem in Eq. (34), we leverage a coordinate descent algorithm as proposed by Friedman et al. [19], which is implemented in the Lasso subroutine of the open-source Python library sklearn. The subroutine takes Aˉ\bar{A} and bˉ\bar{b} as well as the value of λp\lambda_p as input and returns the sparse solution vector θˉ\bar{\theta} whose entries are constrained to be greater than or equal to zero. The intercept in the Lasso subroutine is turned off and the maximum number of iterations is set to 10410^4.

Pareto analysis

The solution of the problem in Eq. (34) is highly dependent on the choice of λp\lambda_p. As qualitatively illustrated in Figure 1, a small value of λp\lambda_p yields a dense solution vector and therefore a complex expression for the material model that is in general associated with a high fitting accuracy, i.e., a small mean squared error. Increasing the value of λp\lambda_p results in a sparser solution vector and thus a simpler expression for the material model at the cost of a reduced fitting accuracy with a larger mean squared error. In the limit of very large values of λp\lambda_p, the optimization problem returns a solution vector with only zero entries and the mean squared error saturates.

Figure 1. Qualitative illustration of the Pareto analysis for selecting an appropriate value of λp\lambda_p.

To strike a balance between the accuracy and the complexity of the material model, a Pareto analysis is applied to the problem. To this end, the problem in Eq. (34) is solved multiple times using a set of different λp\lambda_p values, leading to a solution vector θˉ\bar{\theta} for every choice of λp\lambda_p. Here, we choose 41 values of λp\lambda_p that are evenly distributed on a logarithmic scale between 10−210^{-2} and 10210^{2}. Our objective now is to select from all solutions the one that exhibits an optimal combination of high fitting accuracy and high sparsity. To this end, the mean squared error and the L1L_1-norm of the solution vector are computed for each solution. The minimum and maximum mean squared errors among all solutions are denoted as MSEmin⁡\mathrm{MSE}_{\min} and MSEmax⁡\mathrm{MSE}_{\max}, respectively. Further, we define a threshold mean squared error (see Figure 1) as

MSE‾th=MSE‾min⁡+rλ(MSE‾max⁡−MSE‾min⁡),(35)\overline{\mathrm{MSE}}_{\mathrm{th}} = \overline{\mathrm{MSE}}_{\min} + r_{\lambda}(\overline{\mathrm{MSE}}_{\max} - \overline{\mathrm{MSE}}_{\min}), \tag*{(35)}

where rλr_{\lambda} is a small positive scalar, 0<rλ≪10 < r_{\lambda} \ll1. All solutions for which the mean squared errors are greater than this threshold are expected to exhibit a low fitting accuracy and are thus discarded. From the remaining solutions, i.e., those for which the mean squared error is below MSE‾th\overline{\mathrm{MSE}}_{\mathrm{th}}, we select the sparsest one, i.e., the solution with the lowest value of the L1L_1-norm term (see Figure 1). In this way, a sparse solution with a low mean squared error is obtained, whereby the amount of sparsity is dictated by the user-defined hyperparameter rλr_{\lambda}. In this work we set rλ=0.02r_{\lambda} = 0.02 and keep it constant throughout the analyses.

Thresholding

The solution vector θˉ\bar{\theta} selected in § 3.5 may contain values that are close to zero. As these material parameters and their corresponding features have a vanishing effect on the model response, they are set to zero. Specifically, we define a threshold value θˉth\bar{\theta}_{\mathrm{th}} (here chosen as θˉth=0.01\bar{\theta}_{\mathrm{th}} = 0.01) and we set θˉi=0\bar{\theta}_i = 0 if θˉi<θˉth\bar{\theta}_i < \bar{\theta}_{\mathrm{th}} for all ii.

Feature clustering

Due to the fine discretization of the chosen range of αi\alpha_i values (see § 2), the feature library contains Ogden features with very similar values of αi\alpha_i, which in turn results in a high correlation between these features. While the solution vector obtained by solving the optimization problem with Lasso regularization already exhibits a high degree of sparsity, the sparsity and thus interpretability of the material model can be further improved by grouping together highly correlated features in the solution. To this end, we leverage a clustering algorithm that automatically groups together similar αi\alpha_i values, as qualitatively illustrated in Figure 2. For a similar clustering strategy that was used to group together similar Maxwell elements in viscoelastic constitutive laws discovered with EUCLID, the interested reader is referred to Marino et al. [36].

Figure 2. Qualitative illustration of the feature clustering.

In this paper, we adopt the clustering method DBSCAN (Density-Based Spatial Clustering of Applications with Noise) Ester et al., [11] as implemented in the Python library sklearn. DBSCAN assigns each αi\alpha_i whose corresponding {θˉ}i\{\bar{\theta}\}_i is non-zero to a cluster. This is done in such a way that for each αi\alpha_i in a cluster there exists at least one value αj\alpha_j (with i≠ji \ne j) in the same cluster such that their distance ∣αi−αj∣\lvert\alpha_i - \alpha_j\rvert is smaller than or equal to a predefined value, here chosen as 0.01. The advantage over the k-means clustering algorithm used in Marino et al. [36] is that the needed number of clusters is obtained automatically. After grouping the αi\alpha_i values into a set of clusters, an averaged value αˉ\bar{\alpha} is computed for each cluster as

αˉ=∑kαk{θˉλ}k∑k{θˉλ}k(36)\bar{\alpha}=\frac{\sum_k\alpha_k\{\bar{\theta}_{\lambda}\}_k}{\sum_k\{\bar{\theta}_{\lambda}\}_k} \tag*{(36)}

where kk ranges over all elements in the considered cluster. Afterwards, αˉ\bar{\alpha} is rounded to the closest original value of αi\alpha_i contained in the material model library (see § 2). Thus, we identify for each cluster one value of αi\alpha_i for which the corresponding coefficient in θˉλ\bar{\theta}_{\lambda} is non-zero, while all other entries in θˉλ\bar{\theta}_{\lambda} are set to zero.

Final regression without regularization

By solving the sparse regression problem and applying the clustering method, a small number of relevant features are automatically selected from the originally large library of candidate features. In a final step, all features corresponding to parameters that have been identified as zero are disregarded from the library by removing the corresponding columns from the matrix Aˉ\bar{A}, thus obtaining a reduced system matrix Aˉred\bar{A}_{\mathrm{red}}. Afterwards, the reduced regression problem is solved for the remaining non-zero parameters θˉred\bar{\theta}_{\mathrm{red}}, but this time without introducing any regularization term (i.e., we solve Eq. (34) with λp=0\lambda_p=0).

The motivation behind this last step is twofold. First, while the regularization term in Eq. (34) forces unneeded parameters to zero, it simultaneously shrinks the absolute value of the relevant parameters. Solving the regression problem without regularization for the small number of selected features leads to material parameters that are not affected by such shrinkage. And second, after applying the clustering method, most entries in θˉλ\bar{\theta}_{\lambda} have been identified as zero, while the remaining non-zero parameters in θˉλ\bar{\theta}_{\lambda} are still unknown. The final regression problem without regularization is used to calibrate those non-zero parameters. Finally, the original parameters θ\theta can be recovered from the scaled parameters θˉ\bar{\theta} using Eq. (32).

Numerical verification

Synthetical data

Before applying the proposed method for material model discovery to experimental data, we verify the method on synthetically generated data without and with artificially added noise. Such data are obtained by assuming different hyperelastic material models and generating labeled data pairs under the assumption of uniaxial compression/tension and simple torsion. Specifically, we consider the four material models whose strain energy density functions are provided in Table 1:

BenchmarksStrain energy density W~\widetilde{W} [Pa]MSE [Pa2^{2}]MSE [−]
MR1Truth40.00(I1−3)+20.00(I2−3)40.00 (I_{1} - 3) + 20.00 (I_{2} - 3)--
σ=0\sigma= 040.00(I1−3)+20.00(I2−3)40.00 (I_{1} - 3) + 20.00 (I_{2} - 3)0.00000.0000
σ=5\sigma= 5 Pa41.25(I1−3)+17.71(I2−3)41.25 (I_{1} - 3) + 17.71 (I_{2} - 3)13.41200.0022
σ=10\sigma= 10 Pa42.51(I1−3)+15.42(I2−3)42.51 (I_{1} - 3) + 15.42 (I_{2} - 3)53.64810.0090
O1Truth2.00(λ1−10.00+λ2−10.00+λ3−10.00−3)2.00 \left(\lambda_{1}^{-10.00} + \lambda_{2}^{-10.00} + \lambda_{3}^{-10.00} - 3\right)--
σ=0\sigma= 01.97(λ1−10.03+λ2−10.03+λ3−10.03−3)1.97 \left(\lambda_{1}^{-10.03} + \lambda_{2}^{-10.03} + \lambda_{3}^{-10.03} - 3\right)0.18150.0000
σ=5\sigma= 5 Pa1.94(λ1−10.05+λ2−10.05+λ3−10.05−3)1.94 \left(\lambda_{1}^{-10.05} + \lambda_{2}^{-10.05} + \lambda_{3}^{-10.05} - 3\right)13.53050.0001
σ=10\sigma= 10 Pa1.91(λ1−10.08+λ2−10.08+λ3−10.08−3)1.91 \left(\lambda_{1}^{-10.08} + \lambda_{2}^{-10.08} + \lambda_{3}^{-10.08} - 3\right)53.86060.0006
O2Truth16.00(λ1−5.00+λ2−5.00+λ3−5.00−3)+8.00(λ15.00+λ25.00+λ35.00−3)16.00 \left(\lambda_{1}^{-5.00} + \lambda_{2}^{-5.00} + \lambda_{3}^{-5.00} - 3\right) + 8.00 \left(\lambda_{1}^{5.00} + \lambda_{2}^{5.00} + \lambda_{3}^{5.00} - 3\right)--
σ=0\sigma= 013.50(λ1−5.25+λ2−5.25+λ3−5.25−3)+11.79(λ14.43+λ24.43+λ34.43−3)13.50 \left(\lambda_{1}^{-5.25} + \lambda_{2}^{-5.25} + \lambda_{3}^{-5.25} - 3\right) + 11.79 \left(\lambda_{1}^{4.43} + \lambda_{2}^{4.43} + \lambda_{3}^{4.43} - 3\right)0.29360.0000
σ=5\sigma= 5 Pa13.29(λ1−5.26+λ2−5.26+λ3−5.26−3)+11.79(λ14.44+λ24.44+λ34.44−3)13.29 \left(\lambda_{1}^{-5.26} + \lambda_{2}^{-5.26} + \lambda_{3}^{-5.26} - 3\right) + 11.79 \left(\lambda_{1}^{4.44} + \lambda_{2}^{4.44} + \lambda_{3}^{4.44} - 3\right)13.73490.0002
σ=10\sigma= 10 Pa13.16(λ1−5.26+λ2−5.26+λ3−5.26−3)+11.75(λ14.45+λ24.45+λ34.45−3)13.16 \left(\lambda_{1}^{-5.26} + \lambda_{2}^{-5.26} + \lambda_{3}^{-5.26} - 3\right) + 11.75 \left(\lambda_{1}^{4.45} + \lambda_{2}^{4.45} + \lambda_{3}^{4.45} - 3\right)54.07840.0007
MR2O1Truth30.00(I2−3)2+2.00(λ1−10.00+λ2−10.00+λ3−10.00−3)30.00 (I_{2} - 3)^{2} + 2.00 \left(\lambda_{1}^{-10.00} + \lambda_{2}^{-10.00} + \lambda_{3}^{-10.00} - 3\right)--
σ=0\sigma= 029.25(I2−3)2+1.97(λ1−10.04+λ2−10.04+λ3−10.04−3)29.25 (I_{2} - 3)^{2} + 1.97 \left(\lambda_{1}^{-10.04} + \lambda_{2}^{-10.04} + \lambda_{3}^{-10.04} - 3\right)0.31790.0000
σ=5\sigma= 5 Pa31.69(I2−3)2+1.91(λ1−10.07+λ2−10.07+λ3−10.07−3)31.69 (I_{2} - 3)^{2} + 1.91 \left(\lambda_{1}^{-10.07} + \lambda_{2}^{-10.07} + \lambda_{3}^{-10.07} - 3\right)13.75640.0002
σ=10\sigma= 10 Pa34.16(I2−3)2+1.86(λ1−10.10+λ2−10.10+λ3−10.10−3)34.16 (I_{2} - 3)^{2} + 1.86 \left(\lambda_{1}^{-10.10} + \lambda_{2}^{-10.10} + \lambda_{3}^{-10.10} - 3\right)53.97470.0007

Table 1. Strain energy density functions of the true and discovered material models and MSE of predictions.

  • first-order Mooney-Rivlin model (MR1)

  • one-term Ogden model (O1)

  • two-term Ogden model (O2)

  • combination of second-order Mooney-Rivlin model and one-term Ogden model (MR2O1)

The chosen material models are used to generate nUT=60n_{\mathrm{UT}}=60 pairs of data for uniaxial compression/tension, i.e., (λUT(l),P11(l))(\lambda_{\mathrm{UT}}^{(l)},P_{11}^{(l)}), where the values of λUT(l)\lambda_{\mathrm{UT}}^{(l)} are equally spaced between λUT(1)=0.7\lambda_{\mathrm{UT}}^{(1)}=0.7 and λUT(nUT)=1.3\lambda_{\mathrm{UT}}^{(n_{\mathrm{UT}})}=1.3, and nST=60n_{\mathrm{ST}}=60 pairs of data for simple torsion, i.e., (ψ~(l),τ(l))(\tilde{\psi}^{(l)},\tau^{(l)}), where the values of ψ~(l)\tilde{\psi}^{(l)} are equally spaced between ψ~(1)=−1\tilde{\psi}^{(1)}=-1 and ψ~(nST)=1\tilde{\psi}^{(n_{\mathrm{ST}})}=1.

To emulate real experimental data, the generated data are perturbed by artificial noise by considering noisy data pairs (λUT(l),P11(l)+εUT(l))(\lambda_{\mathrm{UT}}^{(l)},P_{11}^{(l)}+\varepsilon_{\mathrm{UT}}^{(l)}) and (ψ~(l),τ(l)+εST(l))(\tilde{\psi}^{(l)},\tau^{(l)}+\varepsilon_{\mathrm{ST}}^{(l)}), where εUT(l)∼N(0,σ2)\varepsilon_{\mathrm{UT}}^{(l)}\sim\mathcal{N}(0,\sigma^2) and εST(l)∼N(0,σ2)\varepsilon_{\mathrm{ST}}^{(l)}\sim\mathcal{N}(0,\sigma^2) is random noise that is drawn independently from a Gaussian distribution with zero mean and standard deviation σ\sigma. Here, we consider (beside the noiseless case) two different levels of noise, i.e. σ∈{0 Pa,5 Pa,10 Pa}\sigma\in\{0\ \mathrm{Pa},5\ \mathrm{Pa},10\ \mathrm{Pa}\}.

Results and discussion

The synthetically generated data serve as input for the proposed algorithm for material model discovery. Testing the method on synthetical data has the advantage that the discovered material models can be compared to the ”ground truth” (in machine learning jargon), i.e., to the material models that were assumed during data generation. Table 1 shows the expressions of the discovered strain energy density functions in comparison with the true ones. It is observed that the correct mathematical form of the strain energy density function is recovered for each test case. Table 1 further provides the mean squared errors that quantify the mismatch between the data and the predictions of the discovered models. As expected, the MSE increases for increasing level of noise.

For the benchmark case MR1, the material coefficients in the strain energy density function are exactly recovered for the noiseless case. The deviation between the true and identified parameters increases for increasing noise, as expected. For the benchmark cases O1 and MR2O1, the true and discovered parameters are in excellent agreement. However, the material parameters are not exactly recovered even in the noiseless case. The reason for this is that computing the averaged values αˉ\bar{\alpha} after the feature clustering (§ 3.7) cannot exactly recover the ground truth exponents in the Ogden terms, which leads to small deviations in the identified parameters. For the benchmark case O2, the true and identified parameters exhibit slightly larger deviations. One explanation for these deviations could be that the model library comprises many material models and many combinations of material parameters that are equally suited to describe the material response. The proposed algorithm does not guarantee to find exactly the same model and parameters that were assumed during data generation, but may instead provide an adequate surrogate model that is equally suited to predict the data. We emphasise that, although the true and identified material parameters show some deviations, the MSE for the benchmark case O2 is similar to the MSE for the other benchmarks. Thus, the deviation in the model parameters does not seem to seriously affect the fitting accuracy of the model.

Figure 3 illustrates the material response of the discovered material models in direct comparison with the synthetically generated data for the case with the highest level of noise, revealing an excellent agreement.

Figure 3. Stretch versus stress response under uniaxial compression/tension and (normalized) twist versus torque response under simple torsion of the discovered material models in comparison with the synthetical data (noise level σ=10\sigma= 10 Pa).

In the following, we discuss in more detail some of the intermediate steps in the sparsity promoting algorithm for material model discovery (see Steps 3-8 in Fig. B.10) in the context of benchmark case MR2O1 with noise level σ=10\sigma= 10 Pa. Figure 4 illustrates the Pareto analysis, which is leveraged for the choice of the hyperparameter λp\lambda_p in the sparse regression problem. It can be seen that the mean squared error MSE increases and the L1L_1-norm of the material parameter vector ∥θˉ∥1\lVert\bar{\boldsymbol{\theta}}\rVert_1 decreases for increasing values of λp\lambda_p. For values of λp\lambda_p exceeding approximately 1, the material parameter vector obtained from the solution of the sparse regression problem contains all zeros, so that its L1L_1-norm remains constant at zero and the corresponding MSE saturates. Using the method described in § 3.5, the appropriate value of λp\lambda_p is chosen such that the selected model exhibits both a high fitting accuracy and a low model complexity. Note also that for values of λp\lambda_p lower than the chosen one, the MSE is very weakly sensitive to the specific choice of λp\lambda_p.

Figure 4. Illustration of the Pareto analysis for benchmark case MR2O1 (noise level σ=10\sigma= 10 Pa).

In Figure 5, the effect of the clustering algorithm (see § 3.7) is illustrated. Before applying the clustering method, many values of αi\alpha_i are zero while some non-zero values agglomerate in a small region near the ground truth value (equal to 10, see Table 1). The clustering algorithm identifies these values as one cluster. Afterwards, the values of αi\alpha_i belonging to the cluster are averaged, such that the discovered material model exhibits only one Ogden term as the ground truth model, and the feature coefficients are calibrated, as illustrated in § 3.8.

Figure 5. Illustration of the feature clustering for benchmark case MR2O1 (noise level σ=10\sigma= 10 Pa).

Experimental validation

Experimental data

In the context of this work, we use multi-modal large-strain mechanical testing data from 81 cylindrical specimens extracted from three different human brains. The data acquisition and preprocessing are briefly described in the following. For details, the reader is referred to Hinrichsen et al. [24].

81 cylindrical specimens from different regions of the brain are prepared. Each specimen is labeled by a brain number and a specimen number as HBE⟨brain no.⟩⟨specimen no.⟩\mathrm{HBE}_{\langle\text{brain no.}\rangle\langle\text{specimen no.}\rangle}. The specimens have a radius of approximately rout≈4r_{\mathrm{out}} \approx4 mm. The heights of the specimens and the region that they stem from are recorded in Table C.2.

Figure 6 shows one of the human brains and an exemplary cylindrical sample before and after mounting it to the rheometer for the mechanical testing. Each loading mode (compression/tension and torsional shear) consists of three cycles. Here, we use the data from the third cycle representing the preconditioned material response as brain tissue was found to show substantial pre-conditioning behavior [8]. We limit ourselves to hyperelastic material models (neglecting poro- and viscoelastic effects). The strain rates needed to obtain a purely hyperelastic response are (in theory infinitely) high or low and therefore not feasible in actual experiments. Thus, the experimental data obtained from the rheometer shows a considerable hysteresis (see Figure 6) and we extract the hyperelastic response through a preprocessing procedure. First, a moving average as well as a low pass filter is applied to reduce high frequency noises. Afterwards, the hyperelastic response is approximated by the averaged loading and unloading curves (see also Budday et al. [8]). The raw data and the extracted hyperelastic response are illustrated in Figure 6. To reduce the dimensionality of the data while still preserving the characteristic shape of the curve, we reduce the points per deformation mode to 60.

Figure 6. Experimental setup and data preprocessing. Cylindrical samples (b) are extracted from multiple locations within the human brains (a) and then mounted to the rheometer (c). The raw data from the rheometer (blue) is preprocessed to obtain the hyperelastic response (orange) (see (d) and (e)). This is exemplarily shown for a specimen from the motor cortex (HBE 1_8). First, the noise is reduced using a moving average as well as a lowpass filter. Subsequently, the hyperelastic response is obtained by averaging the loading and unloading curve.

This finally leads to a number of nUT=60n_{\mathrm{UT}} = 60 data pairs (λUT(l),P11(l))(\lambda_{\mathrm{UT}}^{(l)}, P_{11}^{(l)}) and nST=60n_{\mathrm{ST}} = 60 data pairs (ψ~(l),τ(l))(\widetilde{\psi}^{(l)}, \tau^{(l)}) acquired from the mechanical tests under uniaxial compression/tension and simple torsion, respectively. The values of λUT(l)\lambda_{\mathrm{UT}}^{(l)} are uniformly distributed between λUT(1)=0.85\lambda_{\mathrm{UT}}^{(1)} = 0.85 and λUT(nUT)=1.15\lambda_{\mathrm{UT}}^{(n_{\mathrm{UT}})} = 1.15 and the values of ψ~(l)\widetilde{\psi}^{(l)} are uniformly distributed between ψ~(1)=−0.3\widetilde{\psi}^{(1)} = -0.3 and ψ~(nST)=0.3\widetilde{\psi}^{(n_{\mathrm{ST}})} = 0.3.

Results and discussion

The proposed algorithm for material model discovery is applied to all experimentally acquired data sets, keeping all hyperparameters and algorithmic settings constant. The resulting material parameters are listed in Table D.4 and Table D.5. Many material parameters are identified as zero, meaning that the discovered expressions of the strain energy density functions are concise and interpretable. The material model discovered for most of the specimens (i.e., about 60% of the specimens) is the one-term Ogden model, which has also previously been used to fit human brain tissue data (Budday et al. [8, 7]; Hinrichsen et al. [24]). Further models that were identified are the two-term Ogden model (about 32% of the specimens), and combinations of the one-term Ogden model with a Mooney-Rivlin term (about 7% of the specimens).

To measure the ability of the discovered material models to fit the given experimental data, the mean squared errors MSE and MSE are provided in Table D.4 and Table D.5. The scaled mean squared error MSE ranges from a minimum value of 0.01 to a maximum value of 0.71, and the average MSE over all experimental data sets is 0.17.

Figure 7 shows the stress versus stretch response under uniaxial compression/tension and torque versus normalized twist response under simple torsion of a discovered material model for which the value of MSEMSE is small in comparison to the other experiments. It is evident that the discovered material model is very well suited to describe the given data. Figure 8 shows the same plots for discovered material models for which the values of MSEMSE are close to the average value of MSEMSE over all experiments. The models are in qualitative agreement with the data. However, especially for the response under uniaxial compression/tension, the models are not capable to precisely match the given data. These deviations could possibly be attributed to modeling assumptions that do not hold true during the mechanical experiments. For example, the geometries of some of the specimens were not ideally cylindrical, because the softer specimens deformed under their own weight. Further, it was assumed throughout the derivations in this paper that the strain state in the specimens is homogeneous under uniaxial compression/tension, and it was assumed that the specimens are fixed in longitudinal direction at the boundaries, but free to move in the transversal directions. During the experiments, however, both ends of the specimens were glued, meaning that the cross-sectional area of the specimens remained unchanged at the glued boundaries. Therefore, the sides of the cylindrical specimens bulged into a barrel shape, resulting in non-homogeneous strain states in the specimens. The constraint that the specimens are fixed in both longitudinal and transversal directions may add additional stiffness to the experimentally measured stress versus stretch response, which could explain the underestimated stress by the discovered material models during uniaxial compression/tension in Figure 8. Another source for the disagreement between the discovered models and the data could be that only isotropic material behavior has been included in the material model library. Thus, possible effects from material anisotropy in the experimental data cannot be predicted by the discovered models.

Figure 7. Stress versus stretch response under uniaxial compression/tension and torque versus (normalized) twist response under simple torsion of a discovered material model in comparison with the experimental data. The mean squared error MSE=0.0091MSE = 0.0091 is the smallest in the data set.

Figure 8. Stress versus stretch response under uniaxial compression/tension and torque versus (normalized) twist response under simple torsion of a discovered material model in comparison with the experimental data. The mean squared errors (MSE\mathrm{MSE} = 0.1657, MSE\mathrm{MSE} = 0.1671, MSE\mathrm{MSE} = 0.1664 for HBE_01.29, HBE_02.15, HBE_03.15, respectively) are close to the average MSE\mathrm{MSE} in the data set.

Finally, Figure 9 shows the stretch versus stress and normalized twist versus torque plots of discovered material models for which the value of MSE is large in comparison to the other experiments. As the large mean squared error indicates, the mismatch between the discovered model and the data is significant. Such large discrepancies are exceptional for the considered experimental data sets (see Table D.4 and Table D.5). For cyclic shear tests, the reason for the large deviation between the model and the data could be erroneous experimental measurements: the two shown samples were not loaded symmetrically during cyclic shear tests but were already twisted before the shear test started. This can happen when a torque is induced during axial loading (for example due to inhomogeneous microstructure of the sample). In this case, the rheometer applies a deformation until the torque goes back to zero. The non-monotonic stress versus stretch response under uniaxial compression/tension in Figure 9a could be a consequence of a low signal-to-noise ratio since this sample is very soft. The non-increasing constant stress plateau under uniaxial compression/tension in Figure 9c could indicate a failure of the glue that connects the specimen with the testing machine.

Figure 9. Stress versus stretch response under uniaxial compression/tension and torque versus (normalized) twist response under simple torsion of discovered material models in comparison with the experimental data. The mean squared errors (MSE = 0.7064, MSE = 0.6107 for HBE 01_24, HBE 01_30, respectively) are the largest in the data set.

Conclusion

EUCLID, a recently proposed computational framework for automatically discovering constitutive models as interpretable symbolic mathematical expressions, was formulated in this work in a supervised setting and validated on the mechanical testing data of human brain specimens. It was shown that the proposed model selection strategy, which comprises sparse regression and feature clustering, is able to automatically discover interpretable constitutive models with satisfactory fitting accuracy to the given uniaxial compression/tension and simple torsion data. The most commonly discovered model was the one-term Ogden model, which has also previously been widely used to fit human brain tissue data. The presented results constitute the first experimental validation of EUCLID. However, several aspects of the proposed method may be improved or extended in future studies. For example, the method proposed in this work is informed by labeled data pairs due to the limited access to full-field displacement and net reaction force data (see Flaschel [13]), is the subject of ongoing research. Moreover, we restricted the model library in which EUCLID searches for a model to the class of isotropic hyperelastic models. As the tissue response is in fact not just hyperelastic but affected by dissipative effects as well as possibly not perfectly isotropic, an important future study could be to further generalize the model library, such that EUCLID can not only select a constitutive model for the human brain tissue within a predefined class of models, but further distinguish between different modeling classes (such as hyperelasticity, viscoelasticity, elastoplasticity), as shown by Flaschel et al. [16] for synthetical data, as well as automatically detect possible anisotropies and identify the corresponding parameters.

Derivatives

Derivatives of the strain invariants

The derivatives of the strain invariants with respect to the deformation gradient are

∂I1∂F=2F,∂I2∂F=2I1F−2FC.(37)\frac{\partial I_1}{\partial\mathbf{F}} = 2\mathbf{F}, \qquad\frac{\partial I_2}{\partial\mathbf{F}} = 2I_1\mathbf{F} - 2\mathbf{F}\mathbf{C}. \tag*{(37)}

Derivatives of the principal stretches

The derivatives of the principal directions depend on the eigenvectors of C=FTF\mathbf{C} = \mathbf{F}^{T}\mathbf{F}, denoted by Ni\mathbf{N}_i, and the eigenvectors of b=FFT\mathbf{b} = \mathbf{F}\mathbf{F}^{T}, denoted by ni\mathbf{n}_i. Under the assumption λ1≠λ2≠λ3≠λ1\lambda_1 \ne\lambda_2 \ne\lambda_3 \ne\lambda_1, it is (see Holzapfel [25])

∂λ1∂F=n1⊗N1,∂λ2∂F=n2⊗N2,∂λ3∂F=n3⊗N3.(38)\frac{\partial\lambda_1}{\partial\mathbf{F}} = \mathbf{n}_1 \otimes\mathbf{N}_1, \qquad\frac{\partial\lambda_2}{\partial\mathbf{F}} = \mathbf{n}_2 \otimes\mathbf{N}_2, \qquad\frac{\partial\lambda_3}{\partial\mathbf{F}} = \mathbf{n}_3 \otimes\mathbf{N}_3. \tag*{(38)}

Derivatives of the feature vectors

The derivatives of the feature vector QI\mathbf{Q}_I with respect to the strain invariants are

∂QI∂I1=[m(I1−3)m−1(I2−3)n−m:n∈{1,…,NMooney}, m∈{0,…,n}]T⊕[0],(39)\frac{\partial\mathbf{Q}_I}{\partial I_1} = \left[ m(I_1-3)^{m-1}(I_2-3)^{n-m}: n \in\{1,\ldots,N_{\mathrm{Mooney}}\},\,m \in\{0,\ldots,n\} \right]^{T} \oplus[0], \tag*{(39)}
∂QI∂I2=[(n−m)(I1−3)m(I2−3)n−m−1:n∈{1,…,NMooney}, m∈{0,…,n}]T⊕[1/I2],\frac{\partial\mathbf{Q}_I}{\partial I_2} = \left[ (n-m)(I_1-3)^m(I_2-3)^{n-m-1}: n \in\{1,\ldots,N_{\mathrm{Mooney}}\},\,m \in\{0,\ldots,n\} \right]^{T} \oplus[1/I_2],

which can be used to calculate the derivatives of the strain energy density contribution W~I\widetilde{W}_I with respect to the strain invariants, i.e.,

∂W~I∂Ia=θI⋅∂QI∂Ia.(40)\frac{\partial\widetilde{W}_I}{\partial I_a} = \boldsymbol{\theta}_I \cdot\frac{\partial\mathbf{Q}_I}{\partial I_a}. \tag*{(40)}

The components of the feature vector Qλ\mathbf{Q}_{\lambda} are defined as

{Qλ(λ1,λ2,λ3)}i=λ1αi+λ2αi+λ3αi−3.(41)\{\mathbf{Q}_{\lambda}(\lambda_1,\lambda_2,\lambda_3)\}_i = \lambda_1^{\alpha_i} + \lambda_2^{\alpha_i} + \lambda_3^{\alpha_i} - 3. \tag*{(41)}

Assuming incompressibility λ1λ2λ3=!1\lambda_1\lambda_2\lambda_3 \overset{!}{=} 1, the components of the feature vector Qλ\mathbf{Q}_{\lambda} can be written as

{Qλ(λ1,λ2)}i=λ1αi+λ2αi+λ1−αiλ2−αi−3.(42)\{\mathbf{Q}_{\lambda}(\lambda_1,\lambda_2)\}_i = \lambda_1^{\alpha_i} + \lambda_2^{\alpha_i} + \lambda_1^{-\alpha_i}\lambda_2^{-\alpha_i} - 3. \tag*{(42)}

Thus, the derivatives of the components of the feature vector Qλ\mathbf{Q}_{\lambda} with respect to the principal stretches are

∂{Qλ(λ1,λ2)}i∂λ1=αi(λ1αi−1−λ1−αi−1λ2−αi),\frac{\partial\{\mathbf{Q}_{\lambda}(\lambda_1,\lambda_2)\}_i}{\partial\lambda_1} = \alpha_i\left(\lambda_1^{\alpha_i-1} - \lambda_1^{-\alpha_i-1}\lambda_2^{-\alpha_i}\right),
∂{Qλ(λ1,λ2)}i∂λ2=αi(λ2αi−1−λ1−αiλ2−αi−1).(43)\frac{\partial\{\mathbf{Q}_{\lambda}(\lambda_1,\lambda_2)\}_i}{\partial\lambda_2} = \alpha_i\left(\lambda_2^{\alpha_i-1} - \lambda_1^{-\alpha_i}\lambda_2^{-\alpha_i-1}\right). \tag*{(43)}

which can be used to calculate the derivatives of the strain energy density contribution W~λ\widetilde{W}_{\lambda} with respect to the principal stretches, i.e.,

∂W~λ∂λi=θλ⋅∂Qλ∂λi.(44)\frac{\partial\widetilde{W}_{\lambda}}{\partial\lambda_i} = \boldsymbol{\theta}_{\lambda} \cdot\frac{\partial\mathbf{Q}_{\lambda}}{\partial\lambda_i}. \tag*{(44)}

Derivatives for uniaxial compression and tension

In the following, we seek to simplify the expression for P11(λUT;θ)P_{11}(\lambda_{\mathrm{UT}};\boldsymbol{\theta}) (see Eq. (16)) by leveraging the characteristics of the kinematic state under uniaxial compression and tension. Considering such kinematic state, the deformation gradient and the resulting right Cauchy-Green strain tensor read

F=[λUT0001λUT0001λUT],C=[λUT20001λUT0001λUT].(45)\mathbf{F} = \begin{bmatrix} \lambda_{\mathrm{UT}} & 0 & 0 \\ 0 & \frac{1}{\sqrt{\lambda_{\mathrm{UT}}}} & 0 \\ 0 & 0 & \frac{1}{\sqrt{\lambda_{\mathrm{UT}}}} \end{bmatrix}, \qquad \mathbf{C} = \begin{bmatrix} \lambda_{\mathrm{UT}}^2 & 0 & 0 \\ 0 & \frac{1}{\lambda_{\mathrm{UT}}} & 0 \\ 0 & 0 & \frac{1}{\lambda_{\mathrm{UT}}} \end{bmatrix}. \tag*{(45)}

Thus, the strain invariants simplify to

I1=λUT2+2λUT,I2=2λUT+1λUT2,(46)I_1 = \lambda_{\mathrm{UT}}^2 + \frac{2}{\lambda_{\mathrm{UT}}}, \qquad I_2 = 2\lambda_{\mathrm{UT}} + \frac{1}{\lambda_{\mathrm{UT}}^2}, \tag*{(46)}

and the principal stretches simplify to

λ1=λUT,λ2=λ3=1λUT.(47)\lambda_1 = \lambda_{\mathrm{UT}}, \qquad \lambda_2 = \lambda_3 = \frac{1}{\sqrt{\lambda_{\mathrm{UT}}}}. \tag*{(47)}

The simple structure of the kinematic state is used to simplify the feature vector Q\boldsymbol{Q}. The feature vectors QI\boldsymbol{Q}_I and Qλ\boldsymbol{Q}_{\lambda} are

QI(λUT)=[(λUT−3)m(2λUT+1λUT2−3)n−m:n∈{1,…,NMooney}, m∈{0,…,n}]T⊕[log⁡(23λUT+13λUT2)].(48)\boldsymbol{Q}_I(\lambda_{\mathrm{UT}}) = \left[ (\lambda_{\mathrm{UT}}-3)^m \left(2\lambda_{\mathrm{UT}}+\frac{1}{\lambda_{\mathrm{UT}}^2}-3\right)^{n-m} : n \in\{1,\ldots,N_{\mathrm{Mooney}}\},\ m \in\{0,\ldots,n\} \right]^T \oplus \left[ \log\left(\frac{2}{3}\lambda_{\mathrm{UT}}+\frac{1}{3\lambda_{\mathrm{UT}}^2}\right) \right]. \tag*{(48)}

and

{Qλ(λUT)}i=λUTαi+2(1λUT)αi−3,(49)\{\boldsymbol{Q}_{\lambda}(\lambda_{\mathrm{UT}})\}_i = \lambda_{\mathrm{UT}}^{\alpha_i} + 2\left(\frac{1}{\sqrt{\lambda_{\mathrm{UT}}}}\right)^{\alpha_i} -3, \tag*{(49)}

whose derivatives with respect to λUT\lambda_{\mathrm{UT}} are trivial. We finally obtain the following expression for the feature vector derivative in Eq. (16)

QUT′(λUT)=∂Q(λUT)∂λUT,(50)\boldsymbol{Q}'_{\mathrm{UT}}(\lambda_{\mathrm{UT}}) = \frac{\partial\boldsymbol{Q}(\lambda_{\mathrm{UT}})}{\partial\lambda_{\mathrm{UT}}}, \tag*{(50)}

which after substitution in Eq. (16) results in a simplified expression for P11(λUT;θ)P_{11}(\lambda_{\mathrm{UT}};\boldsymbol{\theta}).

Derivatives for simple torsion

In the following, we seek to simplify the expression for τ(ψ~;θ)\tau(\tilde{\psi};\boldsymbol{\theta}) (see Eq. (21)) by leveraging the characteristics of the kinematic state under simple torsion. Considering simple torsion, the deformation gradient and the resulting right Cauchy-Green strain tensor read

F=[10001Fϑz001],C=[10001Fϑz0Fϑz1+Fϑz2].(51)\mathbf{F} = \begin{bmatrix} 1 & 0 & 0 \\ 0 & 1 & F_{\vartheta z} \\ 0 & 0 & 1 \end{bmatrix}, \qquad \mathbf{C} = \begin{bmatrix} 1 & 0 & 0 \\ 0 & 1 & F_{\vartheta z} \\ 0 & F_{\vartheta z} & 1+F_{\vartheta z}^2 \end{bmatrix}. \tag*{(51)}

where Fϑz=ρψ~F_{\vartheta z}=\rho\tilde{\psi}. Thus, the strain invariants simplify to

I1=I2=Fϑz2+3.(52)I_1 = I_2 = F_{\vartheta z}^2 + 3. \tag*{(52)}

Defining the auxiliary variable Cˉ=1+12Fϑz2\bar{C}=1+\frac{1}{2}F_{\vartheta z}^2, the eigenvalues of C\mathbf{C} (which are the squares of the principal stretches) read

λ12=Cˉ−Cˉ2−1,λ22=1,λ32=Cˉ+Cˉ2−1,(53)\lambda_1^2 = \bar{C}-\sqrt{\bar{C}^2-1}, \qquad \lambda_2^2 = 1, \qquad \lambda_3^2 = \bar{C}+\sqrt{\bar{C}^2-1}, \tag*{(53)}

which results in the principal stretches

λ1=Cˉ−Cˉ2−1,λ2=1,λ3=Cˉ+Cˉ2−1.(54)\lambda_1 = \sqrt{\bar{C}-\sqrt{\bar{C}^2-1}}, \qquad \lambda_2 = 1, \qquad \lambda_3 = \sqrt{\bar{C}+\sqrt{\bar{C}^2-1}}. \tag*{(54)}

The simple structure of the kinematic state is used to simplify the feature vector QQ. The feature vector QIQ_I is

QI(Fϑz)=[Fϑz2n:n∈{1,…,NMooney},m∈{0,…,n}]T⊕[log⁡(Fϑz2/3+1)],(55)Q_I(F_{\vartheta z}) = \left[F_{\vartheta z}^{2^n}: n \in\{1,\ldots,N_{\mathrm{Mooney}}\},m \in\{0,\ldots,n\}\right]^{T} \oplus\left[\log\left(F_{\vartheta z}^{2}/3+1\right)\right], \tag*{(55)}

whose derivative with respect to FϑzF_{\vartheta z} is trivial, and the feature vector QΛQ_\Lambda is

{QΛ(Cˉ)}i=(Cˉ−Cˉ2−1)αi+(Cˉ+Cˉ2−1)αi−2,(56)\left\{Q_\Lambda(\bar{C})\right\}_i = \left(\sqrt{\bar{C}}-\sqrt{\bar{C}^{2}-1}\right)^{\alpha_i}+\left(\sqrt{\bar{C}}+\sqrt{\bar{C}^{2}-1}\right)^{\alpha_i}-2, \tag*{(56)}

whose derivative with respect to FϑzF_{\vartheta z} can be computed using the chain rule

∂QΛ∂Fϑz=∂QΛ∂Cˉ∂Cˉ∂Fϑz=∂QΛ∂CˉFϑz.(57)\frac{\partial Q_\Lambda}{\partial F_{\vartheta z}}=\frac{\partial Q_\Lambda}{\partial\bar{C}}\frac{\partial\bar{C}}{\partial F_{\vartheta z}}=\frac{\partial Q_\Lambda}{\partial\bar{C}}F_{\vartheta z}. \tag*{(57)}

Thus, the derivative ∂Q∂Fϑz\frac{\partial Q}{\partial F_{\vartheta z}} is known and it depends on ρ\rho and ψˉ\bar{\psi} through Cˉ=1+12Fϑz2\bar{C}=1+\frac{1}{2}F_{\vartheta z}^{2} and Fϑz=ρψˉF_{\vartheta z}=\rho\bar{\psi}. With reference to Eq. (21), it is

QST′(ψˉ)=∫012πρ2∂Q∂Fϑz dρ,(58)Q_{\mathrm{ST}}^{\prime}(\bar{\psi})=\int_{0}^{1}2\pi\rho^{2}\frac{\partial Q}{\partial F_{\vartheta z}}\,\mathrm{d}\rho, \tag*{(58)}

where the integral over ρ\rho can be computed through numerical quadrature.

Algorithm

Fig. B.10 provides a step-by-step description of the proposed algorithm for material model discovery.

Step-by-step description of the sparsity promoting algorithm for material model discovery: Step 1: Compute $\mathbf{A}_{\mathrm{UT}}$, $\mathbf{b}_{\mathrm{UT}}$ and $\mathbf{A}_{\mathrm{ST}}$, $\mathbf{b}_{\mathrm{ST}}$, and assemble $\mathbf{A}$ and $\mathbf{b}$; Step 2: Apply feature scaling to obtain $\bar{\mathbf{A}}$ and $\bar{\mathbf{b}}$; Step 3: Solve the Lasso problem for a set of distinct values of $\lambda_p$; Step 4: Discard all solutions from Step 3 with $\operatorname{MSE}(\bar{\boldsymbol{\theta}}) > \overline{\operatorname{MSE}}_{\mathrm{th}}$; Step 5: Select the solution remaining from Step 4 with the smallest value of $\lVert\bar{\boldsymbol{\theta}}\rVert_1$; Step 6: For all $i$, if $\bar{\theta}_i < \bar{\theta}_{\mathrm{th}}$, set $\bar{\theta}_i = 0$; Step 7: Use the clustering method to group together similar values of $\alpha_i$; Step 8: Apply regression without regularization to calibrate the non-zero entries in $\bar{\boldsymbol{\theta}}$; Step 9: Compute $\boldsymbol{\theta}$ from $\bar{\boldsymbol{\theta}}$

Figure B.10. Step-by-step description of the sparsity promoting algorithm for material model discovery.

Specimen information

The corresponding heights and regions of the different specimens are recorded in Table C.2, while the radius of each specimen is rout≈4 mmr_{\mathrm{out}} \approx4\,\mathrm{mm}. Table C.3 lists the abbreviations of the brain regions and their meaning (see [see 24].

HBERegionhh [mm]HBERegionhh [mm]HBERegionhh [mm]HBERegionhh [mm]
01_03C4.8915902_01CR2.908303_01BS6.180303_21CC4.32991
01_04BG4.4400502_02C4.3639703_02BS5.1746303_22CC3.91166
01_05CR4.6400402_03C3.5688203_03BS6.5277603_23CR5.91647
01_06CR4.1919802_04CR3.7054503_04Am4.0460403_25C4.7642
01_07BG3.8635502_05CC3.7124803_05M5.3919303_26Am4.79861
01_08C5.127802_06CC4.2771603_06M5.2073903_27BG5.46595
01_09BG3.629902_07CC3.859703_07CC3.797503_28BG5.80823
01_10CR3.7946802_08CC4.062903_08CC4.2952603_29CR5.61761
01_12CC4.2977902_09M5.1665403_09BG5.6471803_30CR4.97806
01_13CR3.8979602_10BG4.0014303_10BG4.9609703_31C4.68306
01_14C4.5909702_13M5.2809403_11CC5.1573703_32CR4.01945
01_21C4.4272102_14BG4.8464503_12BG5.9680503_33CR6.07937
01_22CR3.716702_15BG4.6989403_13CC3.2728703_34CR4.66727
01_23C3.7804802_16CR4.9618103_14CB6.7712903_35CR5.81572
01_24CR2.7980402_17C4.6303_15CB6.7476903_36C3.8775
01_25BS3.6142202_18BG3.9164703_16CB6.4054603_37M5.80837
01_26BS4.1138302_19C4.7934503_17CB5.1811203_38M6.11145
01_27CB4.904502_20BS5.4168703_18CR6.1965303_39C4.75102
01_28CB4.679902_21BS4.3606703_19C4.8619203_40CR5.26147
01_29M3.12102_22CB5.3797503_20BG6.9739903_41C4.96854
01_30M4.74689

Table C.2. Heights and regions of the brain tissue specimens.

AmAmygdalaBGBasal gangliaBSBrain stemCCortex
CBCerebellumCCCorpus callosumCRCorona radiataMMidbrain

Table C.3. Abbreviations and full names of the brain regions.

Material parameters

The discovered material models and the corresponding parameters are reported in Table D.4 and Table D.5. The tables further record different measures for the fitting accuracy of the discovered models as well as the computational time needed for the discovery process.

HBEμ1\mu_1α1\alpha_1μ2\mu_2α2\alpha_2I2−3I_2-3(I2−3)2(I_2-3)^2(I2−3)(I1−3)(I_2-3)(I_1-3)(I1−3)2(I_1-3)^2MSE [Pa2\mathrm{Pa}^2]MSE [−-]Time [s]
01_0329.85-38.84------1364.680.26688
01_04125.13-21.14------260.160.08713
01_050.13-68.286.64-33.86----373.010.51718
01_06----33.50---189.600.50638
01_077.38-49.0869.29-25.57----2861.050.27719
01_08350.45-18.80------1327.160.07741
01_09122.55-25.75------878.700.14715
01_101.80-57.89------1027.670.43666
01_1233.75-20.06------16.970.09680
01_130.85-54.1949.02-23.15----251.270.18670
01_14274.80-21.10------606.650.04680
01_212.09-54.3810.20-24.62----872.840.49675
01_222.46-45.7045.62-25.99----291.840.16674
01_2335.76-36.88------983.440.23790
01_2416.35-20.05------140.420.71684
01_250.10-70.6262.52-25.82----540.380.18717
01_26207.64-24.58---392.93--136.290.01758
01_272.37-52.6664.85-24.86----970.580.23708
01_28119.72-18.48---160.40--46.120.02727
01_290.01-78.5890.36-28.71----1138.840.17781
01_3055.97-28.04------3227.890.61743
02_016.03-51.39------1499.170.35816
02_021.37-51.2576.88-22.85----275.260.11816
02_0356.66-34.54------1369.330.20750
02_049.11-46.83------1014.310.32767
02_051.06-51.4816.30-21.06----64.850.20700
02_060.37-46.5516.32-24.76----26.250.18686
02_0753.93-18.72------20.690.05710
02_080.49-50.6742.52-10.72----42.580.18730
02_09134.96-25.83---280.13--211.210.03763
02_107.25-47.26------808.740.34692
02_130.94-51.1172.32-25.43----272.570.10746
02_1492.21-24.97------166.900.06766
02_152.21-52.1458.47-26.20----591.730.17837
02_163.88-46.1619.90-28.55----334.230.24723
02_177.69-44.4219.19-29.34----1013.330.34692
02_1888.59-22.14------92.160.06732
02_1928.46-37.27------746.940.23754
02_204.99-46.9418.22-25.82----363.630.22784
02_2173.98-24.99------117.980.07751
02_222.96-48.9225.56-24.22----298.520.24731

Table D.4. Material parameters, mean squared errors and time to solution for the material model discovery from experimental data - brain no. 01 and 02. Note that model parameters that are zero throughout all experiments are not shown in the table. All material parameters are in Pa, except for the dimensionless parameters αi\alpha_i.

HBEμ1\mu_1α1\alpha_1μ2\mu_2α2\alpha_2I2−3I_2 - 3(I2−3)2(I_2 - 3)^2(I2−3)(I1−3)(I_2 - 3)(I_1 - 3)(I1−3)2(I_1 - 3)^2MSE [Pa2^2]MSE [−-]Time [s]
03_014.13-46.1243.08-26.43----548.090.20703
03_0238.05-19.71------9.050.04694
03_0333.32-30.51------105.640.11793
03_044.24-43.2463.20-23.46----241.050.10753
03_0585.82-22.43------77.840.05710
03_0671.81-28.86------123.950.04717
03_070.53-50.5712.87-22.03----19.290.16709
03_080.97-48.8812.33-17.28----30.730.22711
03_0995.08-20.61------33.180.02726
03_1022.46-30.21------58.020.13776
03_1152.98-16.10------4.300.02708
03_1255.48-29.03------183.620.09744
03_138.98-11.23----41.30-3.300.04685
03_145.19-41.87------86.430.30767
03_1552.15-29.04------344.860.17702
03_164.14-42.41------77.030.33697
03_1722.37-34.83------212.280.18700
03_1852.44-18.07------7.860.02725
03_1935.71-27.60------76.980.11708
03_2069.96-24.83------181.740.11719
03_216.67-33.26------8.020.12748
03_2223.35-19.87-----102.697.630.05781
03_234.50-46.2211.66-26.94----295.750.26737
03_2563.51-29.29------366.860.13795
03_2662.21-20.92------45.170.06770
03_2768.54-23.96------70.190.05764
03_28191.05-18.54------50.770.01740
03_291.84-51.5628.07-19.34----388.020.35693
03_3058.05-21.27------28.160.04688
03_3115.53-40.39------478.730.25728
03_3232.07-25.14------23.060.06730
03_3354.99-23.71------45.310.05745
03_341.21-48.0442.59-24.79----115.990.12742
03_3529.28-25.46------28.110.09775
03_3634.02-32.20------345.650.21760
03_37105.48-23.43------131.430.05766
03_3881.85-22.01------49.050.03725
03_3983.47-26.77------237.350.08693
03_4042.47-23.87------22.890.05692
03_412.90-41.5846.88-29.99----365.950.13677
Average399.570.17729

Table D.5. Material parameters, mean squared errors and time to solution for the material model discovery from experimental data - brain no. 03. Note that model parameters that are zero throughout all experiments are not shown in the table. All material parameters are in Pa, except for the dimensionless parameters αi\alpha_i.

Acknowledgments

MF and LDL acknowledge funding by the Swiss National Science Foundation (SNF) through grant N. 200021 204316 “Unsupervised data-driven discovery of material laws”. SB and PS acknowledge funding by the German Research Foundation (DFG) through grants N. 460333672/CRC1540/1 – 2023 “Exploring Brain Mechanics (EBM)” and BU 3728/1-1. PS acknowledges support from the European Research Council (ERC) through grant N. 101052785, “Configurational Mechanics of Soft Materials (SoftFrac)”.

Code and data availability

Codes and data related to the EUCLID project are available at https://euclid-code.github.io/. The codes corresponding to this work are publically available in the ETH library (Yu et al., 2023) and the mechanical testing data of the human brain tissue are available upon request.

CRediT author statement

MF: Conceptualization, Methodology, Software, Investigation, Writing - Original Draft, Supervision. HY: Methodology, Software, Formal analysis, Investigation, Writing - Original Draft. NR: Resources, Data Curation, Investigation, Writing - Original Draft. JH: Resources, Data Curation, Investigation, Writing - Original Draft. SB: Conceptualization, Resources, Writing - Review & Editing, Funding acquisition. PS: Conceptualization, Resources, Writing - Review & Editing, Funding acquisition. SK: Conceptualization, Methodology, Writing - Review & Editing. LDL: Conceptualization, Methodology, Writing - Review & Editing, Supervision, Funding acquisition.

References

  1. [4]Bomarito, G., Townsend, T., Stewart, K., Esham, K., Emery, J., Hochhalter, J., 2021. Development of interpretable, data-driven plasticity models with symbolic regression. Computers & Structures 252, 106557. URL: https://linkinghub.elsevier.com/retrieve/pii/S0045794921000791, doi:10.1016/j.compstruc.2021.106557.DOI
  2. [5]Boyce, M.C., Arruda, E.M., 2000. Constitutive Models of Rubber Elasticity: A Review. Rubber Chemistry and Technology 73, 504–523. URL: https://meridian.allenpress.com/rct/article/73/3/504/92749/Constitutive-Models-of-Rubber-Elasticity-A-Review, doi:10.5254/1.3547602.DOI
  3. [6]Brunton, S.L., Proctor, J.L., Kutz, J.N., 2016. Discovering governing equations from data by sparse identification of nonlinear dynamical systems. Proceedings of the National Academy of Sciences 113, 3932–3937. URL: http://www.pnas.org/lookup/doi/10.1073/pnas.1517384113, doi:10.1073/pnas.1517384113.
  4. [7]Budday, S., Ovaert, T.C., Holzapfel, G.A., Steinmann, P., Kuhl, E., 2020. Fifty Shades of Brain: A Review on the Mechanical Testing and Modeling of Brain Tissue. Archives of Computational Methods in Engineering 27, 1187–1230. URL: http://link.springer.com/10.1007/s11831-019-09352-w, doi:10.1007/s11831-019-09352-w.DOI
  5. [8]Budday, S., Sommer, G., Birkl, C., Langkammer, C., Haybaeck, J., Kohnert, J., Bauer, M., Paulsen, F., Steinmann, P., Kuhl, E., Holzapfel, G., 2017. Mechanical characterization of human brain tissue. Acta Biomaterialia 48, 319–340. URL: https://linkinghub.elsevier.com/retrieve/pii/S1742706116305633, doi:10.1016/j.actbio.2016.10.036.DOI
  6. [10]Dal, H., Açıkgöz, K., Badienia, Y., 2021. On the Performance of Isotropic Hyperelastic Constitutive Models for Rubber-Like Materials: A State of the Art Review. Applied Mechanics Reviews 73, 020802. URL: https://asmedigitalcollection.asme.org/appliedmechanicsreviews/article/73/2/020802/1108153/On-the-Performance-of-Isotropic-Hyperelastic, doi:10.1115/1.4050978.
  7. [11]Ester, M., Kriegel, H.P., Xu, X., 1996. A Density-Based Algorithm for Discovering Clusters in Large Spatial Databases with Noise. Proceedings of the 2nd International Conference on Knowledge Discovery and Data Mining, Portland , 226–231.
  8. [12]Faber, J., Hinrichsen, J., Greiner, A., Reiter, N., Budday, S., 2022. Tissue-Scale Biomechanical Testing of Brain Tissue for the Calibration of Nonlinear Material Models. Current Protocols 2, e381. URL: https://doi.org/10.1002/cpz1.381, doi:10.1002/cpz1.381, publisher: John Wiley & Sons, Ltd.
  9. [13]Flaschel, M., 2023. Automated Discovery of Material Models in Continuum Solid Mechanics. Ph.D. thesis. ETH Zurich. URL: http://hdl.handle.net/20.500.11850/602750, doi:10.3929/ETHZ-B-000602750.
  10. [14]Flaschel, M., Kumar, S., De Lorenzis, L., 2021. Unsupervised discovery of interpretable hyperelastic constitutive laws. Computer Methods in Applied Mechanics and Engineering 381, 113852. doi:10.1016/j.cma.2021.113852.
  11. [15]Flaschel, M., Kumar, S., De Lorenzis, L., 2022. Discovering plasticity models without stress data. npj Computational Materials 8, 91. URL: https://www.nature.com/articles/s41524-022-00752-4, doi:10.1038/s41524-022-00752-4.DOI
  12. [16]Flaschel, M., Kumar, S., De Lorenzis, L., 2023. Automated discovery of generalized standard material models with EUCLID. Computer Methods in Applied Mechanics and Engineering 405, 115867. URL: https://linkinghub.elsevier.com/retrieve/pii/S0045782522008234, doi:10.1016/j.cma.2022.115867.DOI
  13. [17]Frank, I.E., Friedman, J.H., 1993. A Statistical View of Some Chemometrics Regression Tools. Technometrics 35, 109–135. URL: http://www.tandfonline.com/doi/abs/10.1080/00401706.1993.10485033, doi:10.1080/00401706.1993.10485033.DOI
  14. [18]Frankel, A.L., Jones, R.E., Swiler, L.P., 2020. TENSOR BASIS GAUSSIAN PROCESS MODELS OF HYPERELASTIC MATERIALS. Journal of Machine Learning for Modeling and Computing 1, 1–17. URL: http://www.dl.begellhouse.com/journals/558048804a15188a, 583c4e56625ba94e, 651a2e6b0260f708.html, doi:10.1615/JMachLearnModelComput.2020033325.DOI
  15. [19]Friedman, J., Hastie, T., Tibshirani, R., 2010. Regularization Paths for Generalized Linear Models via Coordinate Descent. Journal of Statistical Software 33. URL: http://www.jstatsoft.org/v33/i01/, doi:10.18637/jss.v033.i01.DOI
  16. [20]Gent, A.N., Thomas, A.G., 1958. Forms for the stored (strain) energy function for vulcanized rubber. Journal of Polymer Science 28, 625–628. URL: http://doi.wiley.com/10.1002/pol.1958.12028118, doi:10.1002/pol.1958.12028118.DOI
  17. [21]Ghaboussi, J., Garrett, J.H., Wu, X., 1991. Knowledge-Based Modeling of Material Behavior with Neural Networks. Journal of Engineering Mechanics 117, 132–153. URL: http://ascelibrary.org/doi/10.1061/(ASCE)0733-9399(1991)117:1(132), doi:10.1061/(ASCE)0733-9399(1991)117:1(132).DOI
  18. [22]Hartmann, S., 2001. Parameter estimation of hyperelasticity relations of generalized polynomial-type with constraint conditions. International Journal of Solids and Structures 38, 7999–8018. URL: https://linkinghub.elsevier.com/retrieve/pii/S002076830100018X, doi:10.1016/S0020-7683(01)00018-X.DOI
  19. [24]Hinrichsen, J., Reiter, N., Bräuer, L., Paulsen, F., Kaessmair, S., Budday, S., 2022. Inverse identification of region-specific hyperelastic material parameters for human brain tissue. URL: http://biorxiv.org/lookup/doi/10.1101/2022.12.19.521022, doi:10.1101/2022.12.19.521022.DOI
  20. [25]Holzapfel, G.A., 2000. Nonlinear solid mechanics: a continuum approach for engineering. Wiley, Chichester ; New York.
  21. [26]Ibáñez, R., Abisset-Chavanne, E., Aguado, J.V., Gonzalez, D., Cueto, E., Chinesta, F., 2018. A Manifold Learning Approach to Data-Driven Computational Elasticity and Inelasticity. Archives of Computational Methods in Engineering 25, 47–57. URL: http://link.springer.com/10.1007/s11831-016-9197-9, doi:10.1007/s11831-016-9197-9.
  22. [27]Joshi, A., Thakolkaran, P., Zheng, Y., Escande, M., Flaschel, M., De Lorenzis, L., Kumar, S., 2022. Bayesian-EUCLID: Discovering hyperelastic material laws with uncertainties. Computer Methods in Applied Mechanics and Engineering 398, 115225. URL: https://linkinghub.elsevier.com/retrieve/pii/S0045782522003681, doi:10.1016/j.cma.2022.115225.DOI
  23. [28]Kabliman, E., Kolody, A.H., Kronsteiner, J., Kommenda, M., Kronberger, G., 2021. Application of symbolic regression for constitutive modeling of plastic deformation. Applications in Engineering Science 6, 100052. URL: https://linkinghub.elsevier.com/retrieve/pii/S2666496821000182, doi:10.1016/j.apples.2021.100052.DOI
  24. [30]Kirchdoerfer, T., Ortiz, M., 2016. Data-driven computational mechanics. Computer Methods in Applied Mechanics and Engineering 304, 81–101. URL: https://linkinghub.elsevier.com/retrieve/pii/S0045782516300238, doi:10.1016/j.cma.2016.02.001.DOI
  25. [34]Linka, K., Reiter, N., Würges, J., Schicht, M., Bräuer, L., Cyron, C.J., Paulsen, F., Budday, S., 2021. Unraveling the Local Relation Between Tissue Composition and Human Brain Mechanics Through Machine Learning. Frontiers in Bioengineering and Biotechnology 9, 704738. URL: https://www.frontiersin.org/articles/10.3389/fbioe.2021.704738/full, doi:10.3389/fbioe.2021.704738.DOI
  26. [35]Marckmann, G., Verron, E., 2006. Comparison of Hyperelastic Models for Hyperelastic Materials. Rubber-Like Materials. Rubber Chemistry and Technology 79, 835–858. URL: https://meridian.allenpress.com/rct/article/79/5/835/93139/Comparison-of-Hyperelastic-Models-for-Rubber-Like, doi:10.5254/1.354796.
  27. [36]Marino, E., Flaschel, M., Kumar, S., De Lorenzis, L., 2023. Automated identification of linear viscoelastic constitutive laws with EUCLID. Mechanics of Materials 181, 104643. URL: https://linkinghub.elsevier.com/retrieve/pii/S0167663623000893, doi:10.1016/j.mechmat.2023.104643.DOI
  28. [37]Meyer, K.A., Ekre, F., 2023. Thermodynamically consistent neural network plasticity modeling and discovery of evolution laws. URL: https://engrxiv.org/preprint/view/2961, doi:https://doi.org/10.31224/2961.
  29. [38]Ogden, R.W., 1972. Large deformation isotropic elasticity – on the correlation of theory and experiment for incompressible rubberlike solids. Proceedings of the Royal Society of London. Series A, Mathematical and Physical Sciences, , 565–584.
  30. [39]Park, H., Cho, M., 2021. Multiscale constitutive model using data–driven yield function. Composites Part B: Engineering 216, 108831. URL: https://linkinghub.elsevier.com/retrieve/pii/S1359836821002225, doi:10.1016/j.compositesb.2021.108831.DOI
  31. [40]Rivlin, R.S., 1947. Torsion of a Rubber Cylinder. Journal of Applied Physics 18, 7.
  32. [42]Sussman, T., Bathe, K.J., 2009. A model of incompressible isotropic hyperelastic material behavior using spline interpolations of tension-compression test data. Communications in Numerical Methods in Engineering 25, 53–63. URL: http://doi.wiley.com/10.1002/cnm.1105, doi:10.1002/cnm.1105.DOI
  33. [43]Tac, V., Sahli Costabal, F., Tepole, A.B., 2022. Data-driven tissue mechanics with polyconvex neural ordinary differential equations. Computer Methods in Applied Mechanics and Engineering 389, 115248. URL: https://linkinghub.elsevier.com/retrieve/pii/S0045782522003838, doi:10.1016/j.cma.2022.115248.DOI
  34. [45]Tibshirani, R., 1996. Regression Shrinkage and Selection via the Lasso. Journal of the Royal Statistical Society: Series B (Methodological) 58, 267–288. URL: http://doi.wiley.com/10.1111/j.2517-6161.1996.tb02080.x, doi:10.1111/j.2517-6161.1996.tb02080.x.DOI
  35. [46]Wang, Z., Estrada, J., Arruda, E., Garikipati, K., 2021. Inference of deformation mechanisms and constitutive response of soft material surrogates of biological tissue by full-field characterization and data-driven variational system identification. Journal of the Mechanics and Physics of Solids 153, 104474. URL: https://linkinghub.elsevier.com/retrieve/pii/S0022509621001459, doi:10.1016/j.jmps.2021.104474.

Paper details

vlnc:W_dg328qq2
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Agricultural and Biological Sciences

Not recorded for this paper

View statement
Looking for related papers…
Contents