betaFeedback

WorksComputer Science

Is Dual Polarization Always Optimal? Unlocking New Spatial Degrees of Freedom

Abstract

Current wireless communication systems are designed based on channel models obtained under the assumption of far-field operation, where electromagnetic waves can be approximated by a planar wave. In those circumstances, dualpolarized antennas seem to be the optimal solution for maximizing the spectral efficiency. However, the recent research on XLMIMO systems represents a paradigm shift, since communication may take place in the near-field and an additional degree of freedom can be achieved. This work presents a modular, lowcost tripolarized antenna at 2.4 GHz band, that is used to experimentally validate theoretical findings about tripolarized antennas, which are commonly based on orthogonal infinitesimal dipoles. The evaluation is carried out in two indoor scenarios and one outdoor scenario, with transmitter comprising multiple tripolarized antennas and a receiver equipped with a single tripolarized antenna. We show that this type of antenna can increase the number of spatial streams up to three or extend the region where terminals are able to achieve two spatial streams

Introduction

Multi-antenna systems have been the cornerstone of the evolution on the wireless communications over the last 30 years, thanks to the increase in available spatial degrees of freedom and/or diversity for communication. The benefits of multi-antenna systems can improve the system throughput by enabling additional streams or increasing the received signal-to-noise ratio (SNR). The latter benefit becomes relevant when communications are carried out at higher frequency bands, [1] or when the channel can be assumed to operate under line-of-sight (LoS) conditions.

Although, even in LoS conditions, additional spatial streams can be transmitted if the transmit and receive antennas satisfy the criterion defined in [2], wireless communication systems have been evolved toward increasing the number of antennas, i.e. massive MIMO systems or holographic MIMO, [3], [4]. By increasing the number of antennas or the antenna aperture length, it is expected that spatial resolution will improve, yielding higher beamforming gain and spatial multiplexing capability. Nevertheless, as the aperture length increases, the conventional far-field assumption used to model the wireless channel and design current wireless systems may no longer hold.

The far-field assumption considers that an electromagnetic (EM) wave can be approximated by a planar wave. However, the new scenario requires working with the actual spherical wave, [3], and the channel models for designing wireless communications should properly account for it. In this regard, an analytical model such as the one presented in [5] is physically consistent, as it follows the principles of antenna theory, derived from Maxwell’s equations, and uses infinitesimal dipoles. A consequence of using a physically consistent channel model that accounts for near-field propagation is that spatial filtering enables not only conventional beamforming, which steers the beam towards a given direction, but also beamfocusing, which concentrates the energy at a specific location [6]. The circumstances under which beamfocusing is feasible, and how the corresponding region can be characterized, have been investigated in [7].

On the other hand, the spectral efficiency of wireless communications can be enhanced by employing antennas with multiple orthogonal polarizations. This is consistent with the dyadic Green’s function channel model, which accounts for polarization through the use of orthogonally oriented dipoles: pol1, pol2, pol3, respectively. According to this channel model, the radiative electromagnetic field does not propagate when the polarization is aligned with the propagation direction, which explains why two polarizations (pol1, pol2) can be effectively exploited in the far-field. In the near- or intermediate-field regions, however, each antenna in an array is effectively observed from a different propagation direction, potentially enabling the exploitation of this third polarization.

Tripolarized antennas have been investigated in the literature, see for example [8], [9], but experimental validation remains limited. To the best of the authors’ knowledge, the first experimental validation of these additional degrees of freedom was presented in [10], where two tripolarized antennas were considered in a scattering medium, i.e., a single-tripolarized antenna at transmitter and another at the receiver side, respectively. Similarly, indoor measurements at 2.45 GHz were carried out in [11] using a design based on three orthogonally aligned, center-fed dipole radiators, each 5.4 cm long. With antenna separations of 1 m and 2 m under LoS and non-LOS conditions, i.e. with scattering, the authors evaluate the classic parameters related to polarization, correlation and time dispersion.

Unlike prior work on tripolarized XL-MIMO, this work presents a practical modular antenna and experimentally validates the main results obtained in [12], [13] showing that the number of available spatial degrees of freedom depends on the aperture length and the relative position of transmitter and receiver. The key contributions presented in this paper are as follows:

  • We present a modular and low-cost design for tripolarized antennas based on a combination of patch antenna

This work was supported by the WAVE-XL project (PID2024- 160457OB-I00) funded by MCIN/AEI/10.13039/501100011033 and by FEDER, UE. (pol1, pol2) and a monopole (pol3), in contrast to the designs adopted in [10], [11].

  • We perform indoor and outdoor measurements at 2.45 GHz to evaluate the number of available spatial degrees of freedom and to asses how well they match the analytical characterization in [13].

  • We provide access to estimated wireless channel matrices from the collected measurements at [14].

Analytical Characterization

The scenario considered for analytical characterization developed in [13] is presented in Figure 1-a). It is assumed to be a transmitting uniform linear array (ULA) with 2M+12M+1 elements separated by a distance ΔT\Delta_T meters (m), deployed along the yy-axis with an aperture length of Λ\Lambda (m). Each element of the array consists of three orthogonal dipoles, each fed by different radio-frequency chain and oriented as follows: pol1 along the xx-axis, pol2 along the yy-axis, and pol3 along the zz-axis. Similarly, the receiver is equipped with a single tripolarized antenna and is assumed to be at distance D>0D>0 and elevation θ∈(−π/2,π/2)\theta\in(-\pi/2,\pi/2), under LoS conditions. The number of employed polarizations at the transmitter and receiver sides will be denoted by tpolt_{\mathrm{pol}} and rpolr_{\mathrm{pol}}, respectively.

Uniform Linear Array and boundary regions

Figure 1. a) Uniform Linear Array with 2M+12M+1 elements and aperture length Λ\Lambda, where each element has 3 orthogonal infinitesimal dipoles. Receiver at distance DD on the yzyz-plane. b) Boundary region for n+=1→2n_+=1\to2 under tpol×rpol=2×3t_{\mathrm{pol}}\times r_{\mathrm{pol}}=2\times3. c) b) Boundary region for n+=2→3n_+=2\to3.

Since the receiver consists of three dipoles, the communication channel can support up to three spatial degrees of freedom, denoted by n+∈1,2,3n_+\in1,2,3. For a fixed transmit power, three spatial streams (n+=3n_+=3) are typically available in the vicinity of the ULA, whereas only one (n+=1n_+=1) is available sufficiently far from the array. Figure 1-b)-c) illustrate the extent of these regions for different ULA sizes and SNR values, considering tpol=2t_{\mathrm{pol}}=2 and tpol=3t_{\mathrm{pol}}=3. More specifically, Figure 1-b) shows the boundaries separating the regions where n+=2n_+=2 and n+=3n_+=3 spatial DoF are available for a ULA with M=8M=8 (17 tripolarized antennas), over an area of 8m×5m8\mathrm{m}\times5\mathrm{m}. The boundaries are shown for the configurations tpol×rpol=2×3t_{\mathrm{pol}}\times r_{\mathrm{pol}}=2\times3 (red lines) and tpol×rpol=3×3t_{\mathrm{pol}}\times r_{\mathrm{pol}}=3\times3 (blue lines), at different transmit powers (normalized SNR values). The results show that the region in which n+=3n_+=3 spatial DoF are available expands when all antennas operate with three polarizations.

On the other hand, Figure 1-c) considers a small ULA with M=1M=1 (three tripolarized antennas) and shows the boundaries separating the regions where n+=1n_+=1 and n+=2n_+=2 spatial DoF are available over an area of 5m×14m5\mathrm{m}\times14\mathrm{m}, for different transmit powers (normalized SNR values). In this case, two spatial DoF (n+=2n_+=2) are available throughout the considered area when tpol=3t_{\mathrm{pol}}=3, and hence, no boundary is observed. Such a boundary exists only for the configuration tpol×rpol=2×3t_{\mathrm{pol}}\times r_{\mathrm{pol}}=2\times3. Note that the availability of two spatial DoF (n+=2n_+=2) is confined to a region around the broadside direction of the ULA.

The boundaries in Figure 1-b) and 1-c) can be analytically described as it is shown in [13]. We summarize the main results in the following lemma.

Lemma 1. Let ρ0\rho_0 denote a D2D^2-normalized version of the SNR, essentially proportional to the transmit power (see [13] for the exact definition). The number of available spatial DoFs n+n_+ and the corresponding availability regions depend on the transmit polarization configuration as follows.

When tpol=3t_{\mathrm{pol}}=3, rpol=3r_{\mathrm{pol}}=3:

  • n+>1n_+>1 is guaranteed everywhere if ρ0>Λ2/12\rho_0>\Lambda^2/12

  • The distance at which the transition between n+=2n_+=2 and n+=3n_+=3 occurs can be asymptotically approximated by

Dth(2)=Λ2A1(θ)+A12(θ)−A2(θ)+2cos⁡2θ3Λ2ρ0(1)D_{\mathrm{th}}^{(2)}=\frac{\Lambda}{2}\sqrt{A_1(\theta)+\sqrt{A_1^2(\theta)-A_2(\theta)+\frac{2\cos^2\theta}{3\Lambda^2}\rho_0}} \tag*{(1)}

with A1(θ)=3/2−29/15cos⁡2θA_1(\theta)=3/2-29/15\cos^2\theta, A2(θ)=2−8/3cos⁡2θA_2(\theta)=2-8/3\cos^2\theta.

When tpol=2t_{\mathrm{pol}}=2, rpol=3r_{\mathrm{pol}}=3:

  • If θ=0\theta=0, n+=2n_+=2 modes are always available.

  • For θ≠0\theta\ne0, we can asymptotically describe the distances at which the two transitions occur as

Dth(1)=Λ24cos⁡4θ−16cos⁡2θ+103sin⁡2θ+4ρ0Λ2tan⁡2θ(2)D_{\mathrm{th}}^{(1)}=\frac{\Lambda}{2}\sqrt{\frac{4\cos^4\theta-16\cos^2\theta+10}{3\sin^2\theta}+\frac{4\rho_0}{\Lambda^2\tan^2\theta}} \tag*{(2)}
Dth(2)=Λ2B1(θ)+B12(θ)−B2(θ)+2cos⁡4θ3Λ2ρ0(3)D_{\mathrm{th}}^{(2)}=\frac{\Lambda}{2}\sqrt{B_1(\theta)+\sqrt{B_1^2(\theta)-B_2(\theta)+\frac{2\cos^4\theta}{3\Lambda^2}\rho_0}} \tag*{(3)}

with B1(θ)=1/12cos⁡4θ−59/20cos⁡2θ+64/30B_1(\theta)=1/12\cos^4\theta-59/20\cos^2\theta+64/30, B2(θ)=482/75−2/9cos⁡6θ+1138/175cos⁡4θ−6437/525cos⁡2θB_2(\theta)=482/75-2/9\cos^6\theta+1138/175\cos^4\theta-6437/525\cos^2\theta.

Having introduced the main analytical results, we now turn to their experimental validation.

Tripolarized Antenna Implementation

The proposed cost-effective solution is based on a modular design in which each tripolarized antenna element consists of two components in the same aperture: (i) dual-polarized antenna or patch antenna, and (ii) a perpendicular monopole providing the third polarization. The fabricated Printed Circuit Board (PCB) for the dual polarized antennas (pol1 and pol2) has dimensions 68.75×68.7568.75\times68.75 mm, with a metallic patch of 43.1×43.143.1\times43.1 mm. The bottom layer is free of metal, and the PCB includes two non-plated holes to allow the connector to pass through and facilitate soldering from the top, as shown in Figure 2-a). Regarding the PCB for the monopole (pol3), multiple holes are provided to allow the antenna to be moved along zz-axis, either closer or farther from the ground plane. Both types of antennas are supported by a single structure, in which the monopole can be adjusted at different positions along the xx-axis or, alternatively, multiple monopoles can be used per patch antenna, as shown in Figure 2-b).

Patch and monopole antennas, supporting structure, tripolarized antenna, matching and isolation performance, and radiation diagram

Figure 2. a) Patch and monopole antennas. b) Structure to support both type of antennas. c) 2 × 1 Tripolarized antenna. d) Matching and isolation performance indicators for tripolarized antenna. e) Radiation diagram for 2 × 1 ULA.

The performance of the tripolarized antenna is evaluated in terms of matching and isolation, as shown in Figure 2-c) and measured with a vector network analyzer. The dual polarized antenna achieves a matching better than 10 dB at 2.45 GHz and 8 dB across the entire operating band (2.4-2.5 GHz). Likewise, the isolation between the two polarizations is at least of 20 dB. When comparing the dual-polarized and monopole ports, the isolation between pol1 and pol3 exceeds 20 dB, whereas pol2 and pol3 is around 10.5 dB. Regarding the matching, it is approximately 10 dB, similar to the dual-polarized case. In total, 20 tripolarized antennas have been manufactured and distributed across two 2 × 1 arrays, as shown at Figure 2-b), and two 8 × 1 ULAs.

Finally, the radiation pattern has been characterized using a standard-gain horn (SGH) with single polarization as the probe in an anechoic chamber. The antenna under test was rotated in azimuth and elevation to extract the 3D radiation pattern. In a 2×1 configuration, such as the one depicted in Figure 2-c), the radiation pattern obtained with only the dual-polarized antennas is shown at Figure 2-d), attaining the maximum at θ=0∘\theta= 0^\circ with an isolation of 20 dB between polarizations. When considering the monopole antennas, the radiation pattern exhibits a null at θ=0\theta= 0, while the maximums are obtained at θ=±π/2\theta= \pm\pi/2. Notice that the monopole complements the dual-polarized antennas providing additional coverage.

Experimental Results

Scenario

The experimental validation is carried out through an over-the-air transmission of narrowband signal with 1 MHz band-width, where the transmitter assigns a different 2047-length Gold sequence as a pilot to each employed polarization along the array. The receiver estimates the equivalent channel using known pilot sequences, which provides information about the number spatial modes. This is made by the modular laboratory infrastructure deployed at CTTC within the framework of the national project UNICO22 EMERGE6G, that enables the evaluation of new waveforms, integrated communication and sensing techniques and prototype antenna testing. The infrastructure has been specifically designed to validate emerging wireless concepts involving large-scale antenna arrays. The system provides up to 96 radio frequency (RF) chains distributed across 12 Software Defined Radios (SDRs) operating up to 6 GHz and arranged over three racks. All transceivers, at both the transmitter and receiver side, are synchronized using a 1 Pulse per Second (PPS) signal and 10 MHz reference clock, enabled by White-Rabbit-based devices. More details on the architecture and the transmission set up can be found at [14].

The validation was carried out in three different scenarios, as shown in Figure 3. The evaluation of the regions where up to n+=3n_{+}=3 spatial modes can be found, as shown in Figure 1-c), was conducted in a laboratory with approximate dimensions 4m × 5m, as depicted in Figure 3-a). The transmitter consists of two 8 × 1 ULAs separated by 0.26 m, yielding an equivalent aperture length of Λ=1.74\Lambda= 1.74 m. In total 48 RF chains are used to transmit the signal over-the-air when tpol=3t_{\mathrm{pol}} = 3 or 32 RF chains when tpol=2t_{\mathrm{pol}} = 2. At the receiver side, 3 RF chains are required when rpol=3r_{\mathrm{pol}} = 3 or 2 RF chains if rpol=2r_{\mathrm{pol}} = 2.

Indoor and outdoor experimental scenarios

Figure 3. a) Indoor scenario with a transmitter of Λ=1.74\Lambda= 1.74 m (48 RF chains) to show n+={2,3}n_{+} = \{2, 3\} spatial modes. b) Indoor scenario with a transmitter of Λ=0.06\Lambda= 0.06 m (6 RF chains) to show n+={1,2}n_{+} = \{1, 2\} spatial modes. c) Outdoor scenario with a transmitter of Λ=0.06\Lambda= 0.06 m to show n+={1,2}n_{+} = \{1, 2\} spatial modes.

In contrast, for the validation of the boundary for n+=1→2n_{+}=1\to2 we considered a much larger space and reduced aperture length to use a total of two active antennas. This selection allows us to compare the results with those presented in Figure 1-b); otherwise the boundary widens. To this end, we considered two cases: (i) an indoor scenario, an auditorium with approximate dimensions 6m × 15m as depicted in Figure 3-b), and (ii) an outdoor scenario, as presented in Figure 3-c). Notice that, for this set up, the transmitter requires only 6 RF chains when tpol=3t_{\mathrm{pol}} = 3 or 2 RF chains when tpol=2t_{\mathrm{pol}} = 2 that is, a single SDR, which facilitates the evaluation across multiple scenarios since it not required to move the three racks with the SDRs. Measurements, which are available at [14], were obtained with the receiver placed at different positions. At each position, the following combinations were evaluated: tpol×rpol=(3×3),(2×3),(2×2)t_{\mathrm{pol}} \times r_{\mathrm{pol}} = (3 \times3), (2 \times3), (2 \times2). In all cases, the patch antenna polarizations, pol1,pol2, remained active. The tpol×rpol=(2×2)t_{\mathrm{pol}} \times r_{\mathrm{pol}} = (2 \times2) configuration represents a conventional dual-polarized wireless system.

Performance Indicators

To compare the experimental results with the theoretical ones under pure LoS conditions, we have considered the eigenvalues of the normalized Gramian of the channel, as depicted in Figure 4, together with the number of spatial streams for the configurations (3×3),(2×3)(3 \times3), (2 \times3) and (2×2)(2 \times2), as shown in Figure 5 and Figure 6. The experimental measurements have been calibrated at each position and for each configuration by matching the trace of the measured Gramian matrix to that of its ideal counterpart, thereby ensuring the same spectral sum, i.e., the same sum of eigenvalues.

Distribution of the eigenvalues of the normalized Gramian

Figure 4. Distribution of the eigenvalues of the normalized Gramian of the measured channel (blue, yellow and red) and LoS channel (black, green, magenta). a) Indoor scenario with Λ=1.74\Lambda= 1.74 m (see Figure 3.a). b) Indoor scenario with Λ=0.06\Lambda= 0.06 m (see Figure 3.b). c) Outdoor scenario with Λ=0.06\Lambda= 0.06 m (see Figure 3.c).

Measured spatial streams

Figure 5. Measured spatial streams. a) Indoor scenario with Λ=1.74\Lambda= 1.74 m (see Figure 3.a) with ρ0={15,20,30}\rho_0 = \{15, 20, 30\} dB (green, blue, yellow). b) Indoor scenario (see Figure 3.b) and c) Outdoor scenario (see Figure 3.c), both with Λ=0.06\Lambda= 0.06 and ρ0={5,10,20}\rho_0 = \{5, 10, 20\} dB (green, blue, yellow).

Ideal spatial streams

Figure 6. Ideal spatial streams. a) Indoor scenario with Λ=1.74\Lambda= 1.74 m (see Figure 3.a) with ρ0={15,20,30}\rho_0 = \{15, 20, 30\} dB (green, blue, yellow). b) Indoor scenario (see Figure 3.b) and c) Outdoor scenario (see Figure 3.c), both with Λ=0.06\Lambda= 0.06 and ρ0={5,10,20}\rho_0 = \{5, 10, 20\} dB (green, blue, yellow).

  1. Eigenvalues: The Gramian matrices have at most three eigenvalues, depending on the polarization configuration. In Figure 4, the colors blue, yellow, and red denote the first, second and third eigenvalue for the experimental Gramian matrix, respectively, while black, green and magenta denote those of the ideal Gramian matrix. At each point, the magnitude of the three eigenvalues are stacked in a colored bar.

  1. Spatial streams (n+n_{+}): The number of active spatial streams is related to the eigenvalues and to the SNR (ρ0\rho_{0}), [13]. Results in Figure 5 and Figure 6 illustrate the dependence of n+n_{+} on ρ0\rho_{0} with different colored bars.

Extending the limits of spatial DoF to n+=3n_{+} = 3

According to the theoretical results presented in section II, the experimental scenario depicted in Figure 3.a) has the appropriate dimensions and aperture length to achieve n+=3n_{+} = 3 spatial streams with (3×3),(2×3)(3 \times3), (2 \times3) polarization configurations. Figure 4-a) presents the magnitude of the eigenvalues at the different measured positions, comparing the measured and ideal cases. The results reveal the following key observations:

  • O1: The experimental eigenvalue distribution differs slightly from the theoretical one. The first experimental eigenvalue (blue) is higher than the first theoretical eigenvalue (black), and a similar trend is observed for the third eigenvalue, red and magenta, respectively.

  • O2: In the (2×3)(2 \times3) and (2×2)(2 \times2) configurations, the spectral sum, i.e. sum of eigenvalues, remains approximately constant at positions along the antenna broadside, located at (0,0,0)(0,0,0). Away from broadside, it decreases, while the first eigenvalue remains larger than the second. By contrast, the (3×3)(3 \times3) configuration maintains a constant spectral sum across all positions.

Previous observations are essential for explaining the spatial streams shown in Figure 5a). As expected, (3×3)(3 \times3) configuration attains n+=3n_{+} = 3 over a larger region than the (2×3)(2 \times3) configuration at ρ0=20\rho_{0} = 20 dB (blue bars). The theoretical characterization identifies closed regions in which the different spatial streams can observed, see Figure 6. However, Figure 5a) shows that points around (−3,4)(-3,4) and (1,3)(1,3), both configurations get n+=3n_{+} = 3, whereas nearby points just get n+=2n_{+} = 2. Notice that the magnitude of the ideal third eigenvalue for those positions is zero, while the experimental measurements is larger than zero. These results suggest that the scenario is not purely LoS with some scattering, increasing the number of spatial streams. In should be also noted that these positions are close to the large glass window and table with equipment.

Expanding the regime for n+=2n_{+} = 2

Section II has shown that use of tripolarized antennas is beneficial for extending the area where at least n+=2n_{+} = 2 spatial streams are achievable. If tripolarized antennas are not employed simultaneously at transmitter and receiver, the region supporting n+=2n_{+} = 2 is concentrated around the antenna broadside, and its width depends on aperture length and ρ0\rho_{0}. Here, we study the case of a small aperture length of Λ=0.06\Lambda= 0.06 m in an indoor and outdoor scenarios introduced in Figure 3.b and Figure 3.c, respectively.

The obtained results for the spectral sum are presented in Figure 4.b and Figure 4.c. Observations O1 and O2 also apply here. In particular, the experimental measurements in the indoor case exhibit a non-zero third eigenvalue, but this does not translate into an increase in the number of spatial streams for the SNR of interest, see Figure 5.b. An additional key observation in this case is the following:

  • O3: For some terminal positions the (3×3)(3 \times3) configuration attains n+=1n_{+} = 1 spatial stream.

Although the number of spatial streams obtained with (3×3)(3 \times3) is always greater than or equal those attained with (2×3)(2 \times3) and (2×2)(2 \times2), as expected, in certain cases for indoor and outdoor scenarios only n+=1n_{+} = 1 can be attained, mainly when terminal is not in the broadside or far from the transmitting antenna. This result appears to contradict Lemma 1, which states that n+=2n_{+} = 2 is achievable everywhere. However, this is due to the fact that even in the considered outdoor scenario in there is some scattering. Specifically, reflections from the concrete floor in the outdoor scenario, see Figure 3.c, affect the magnitudes of the first and second eigenvalues. Notice that, in the ideal scenario, the first and second eigenvalues under (3×3)(3 \times3) configuration attain the same value. This is also observed in the experimental eigenvalues when the terminal is placed close to the transmitter, for example at (0,2)(0,2) in Figure 4.c. However, the values differ when terminal is located at the edge, i.e. at (−4,2)(-4,2), leading to the selection of a single spatial stream.

Open Research Lines

This work presents a preliminary experimental validation of new spatial degrees of freedom under real-world conditions. However, further research is required along several directions.

  • Antenna manufacturing: The prototype antenna design has demonstrated satisfactory performance for the experimental validations. Further iterations could improve matching and isolation associated with pol3, while improving the available bandwidth, compactness, and scalability to higher frequency operation.

  • Polarization reconfigurability: Increasing the number of available orthogonal polarization ports enables active polarization control, adapting the radiating field to propagation environment and variations in antenna orientations. Further research is needed to develop techniques that reduce the complexity of XL-MIMO antenna arrays and potentiality decrease the number of RF chains, [15].

  • Impact of scattering: Although it is known that the scattering can help to increase the number of available degrees of freedom, analytical tractable frameworks for quantifying its impact on the XL-MIMO systems remain

limited. Further research is needed to understand how the spatial degrees of freedom evolve in scenarios with a finite number scatterers, including environments with Reconfigurable Intelligent Surfaces (RIS).

Conclusion

Tripolarized antennas have become an essential tool for improving the performance of wireless communications systems, as they can extend the region where n+=2n_+ = 2 spatial modes are available and even achieve n+=3n_+ = 3 spatial modes when the transmitter has an adequate aperture length, according the existing results in the literature under LoS conditions. Since the literature often uses orthogonal infinitesimal dipoles to simplify the analytical problem, we present a modular linear array based on a low-cost and simple tripolarized antenna design that combines a patch antenna with two polarizations and a monopole with one polarization, operating in the 2.4 GHz band. This configuration is shown to achieve acceptable matching and isolation for wireless communications. The new antennas have been evaluated in three different scenarios: two indoor and one outdoor, revealing the superior performance of the tpol×rpol=(3×3)t_{\mathrm{pol}} \times r_{\mathrm{pol}} = (3 \times3) over the cases (2×3)(2 \times3), and (2×2)(2 \times2), where the later corresponds to the conventional dual-polarized antenna based on patch antennas. The evaluation in the 2.4 GHz band has revealed some discrepancies with the theoretical results due the existence of small scattering components, which would disappear when communication is carried out in pure LoS channel, for example by increasing the carrier frequency. The obtained results opens the door to consider more advanced tripolarized antenna design.

Dr. Adrian Agustin (Senior Member, IEEE) (ORCID 0000-0002-5723-9739) is a Senior Researcher at the Centre Tecnològic de Telecomunicacions de Catalunya (CTTC), at ISPIC Research Unit. He received the M.S. and Ph.D in Telecommunication from Universitat Politècnica de Catalunya (UPC), Barcelona, Spain in 2000 and 2008, respectively. From 2008 to 2019 he was a research associate at the SPCOM group at UPC working in the different research areas of wireless communications. In April 2021, he joined the CTTC. He has participated in the EC funded and training networks and several contracts with industry. He has co-advised 3 PhD Thesis and 4 Master Thesis. He collaborated in 4 book chapters, published around 80 papers in conferences and journals, and participated in 3 patents. He is interested in different research areas for developing next generation wireless communications at L1, L2, with Extremely Large Antenna Arrays (ELAA) or XL-MIMO, Deep-Reinforcement Learning (DRL) and Random Access Networks.

Dr. Xavier Mestre (Senior Member, IEEE) (ORCID 0000-0002-5723-9739) is Scientific Coordinator at CTTC. He received his MS and PhD in Electrical Engineering in 1997 and 2002 and a licentiate in Mathematics in 2011 from the Technical University of Catalonia (UPC). After working at UPC, he joined CTTC in 2003. He has participated in 12 European projects and coordinated one of them (EMPhAtiC). He led industrial, ESA, and Spanish government projects. He holds four patents and has authored more than 50 journal papers and more than 100 conference articles. He has received two best-paper awards, supervised five PhD theses, and delivered multiple keynotes. His service includes editorial roles with IEEE Transactions on Signal Processing, IEEE and EURASIP technical committee memberships, and conference leadership roles, including chairing or co-chairing IEEE ICASSP in 2020 and 2026.

Mr. Carlos Suárez García (ORCID 0000-0001-6346-4687) is a Senior Antenna Engineer at CELESTIA TTI, in Santander, Spain. He received the Bachelor and the M.S in Telecommunication from Universidad de Oviedo (UniOvi), Gijón, Spain in 2018 and 2020, respectively. From 2021 up to now, he has worked as an antenna engineer for different applications, including SatCom, radar, defense and mobile communications.

Mr. Alberto Pellón Sancho is Head of the antenna department at CELESTIA TTI, in Santander, Spain. His main areas of expertise include SOTM, man-pack, and phased-array satellite terminals, as well as broadband and multibeam antennas for spaceborne and ground gateway applications.

References

  1. [1]M. Shafi, J. Zhang, H. Tataria, A. F. Molisch, S. Sun, T. S. Rappaport, F. Tufvesson, S. Wu, and K. Kitao, “Microwave vs. millimeter-wave propagation channels: Key differences and impact on 5G cellular systems,” IEEE Communications Magazine, vol. 56, no. 12, pp. 14–20, 2018.DOI
  2. [2]E. Torkildson, U. Madhow, and M. Rodwell, “Indoor millimeter wave MIMO: Feasibility and performance,” IEEE Transactions on Wireless Communications, vol. 10, no. 12, pp. 4150–4160, 2011.DOI
  3. [3]L. Sanguinetti, A. D’Amico, and M. Debbah, “Wavenumber-division multiplexing in line-of-sight holographic MIMO communications,” IEEE Trans. on Wireless Comm., vol. 22, no. 4, pp. 2186–2201, 2023.arxiv.org/abs/2106.12531
  4. [4]D. Dardari and N. Decarli, “Holographic communication using intelligent surfaces,” IEEE Communications Magazine, vol. 59, no. 6, pp. 35–41, 2021.arxiv.org/abs/2012.01315
  5. [5]A. Poon, R. Brodersen, and D. Tse, “Degrees of freedom in multiple-antenna channels: a signal space approach,” IEEE Transactions on Information Theory, vol. 51, no. 2, pp. 523–536, 2005.DOI
  6. [6]E. Björnson, C.-B. Chae, R. W. Heath Jr, T. L. Marzetta, A. Mezghani, L. Sanguinetti, E. Rusek, M. R. Castellanos, D. Jun, and Ö. T. Demir, “Towards 6G MIMO: Massive spatial multiplexing, dense arrays, and interplay between electromagnetics and processing,” arXiv preprint arXiv:2401.02844, 2024.arxiv.org/abs/2401.02844
  7. [7]X. Mestre and A. Agustin, “Beamfocusing capabilities of a uniform linear antenna array in the holographic regime,” IEEE Transactions on Signal Processing, vol. 73, pp. 5015–5031, 2025.
  8. [8]Y. Yang, C.-X. Wang, J. Huang, J. Thompson, and H. V. Poor, “A 3d continuous-space electromagnetic channel model for 6g tri-polarized multi-user communications,” 2025. [Online]. Available: https://arxiv.org/abs/2501.03608
  9. [9]L. Wei, C. Huang, G. C. Alexandropoulos, Z. Yang, J. Yang, W. E. I. Sha, Z. Zhang, M. Debbah, and C. Yuen, “Tri-polarized holographic MIMO surfaces for near-field communications: Channel modeling and precoding design,” IEEE Trans. on Wireless Comms., pp. 1–1, 2023.DOI
  10. [10]M. R. Andrews, P. P. Mitra, and R. deCarvalho, “Tripling the capacity of wireless communications using electromagnetic polarization,” Nature, no. 1, pp. 1476–4687, 2001.pubmed.ncbi.nlm.nih.gov/11201734
  11. [11]G. Gutierrez, A. Habib, and M. Rupp, “Indoor measurements by dual tripole antennas,” in 2012 Loughborough Antennas & Propagation Conference (LAPC), 2012, pp. 1–5.
  12. [12]A. Agustin and X. Mestre, “Exploiting multiple polarizations in extra large holographic mimo,” IEEE Transactions on Wireless Communications, vol. 25, pp. 6130–6144, 2026.arxiv.org/abs/2410.08839
  13. [13]X. Mestre and A. Agustin, “Available degrees of spatial multiplexing of a uniform linear array with multiple polarizations: A holographic perspective,” IEEE Open Journal on Signal Processing, 2025.arxiv.org/abs/2410.19497
  14. [14]A. Agustin and X. Mestre, “Indoor and outdoor tripolarized channel measurements at 2.4 ghz,” Dataset, https://doi.org/10.5281/zenodo.23472958, 2026, version 1.0. [Online]. Available: https://gitlab.cttc.es/aagustin/tripolarized-antenna-measurements
  15. [15]J. Ding, Z. Zhou, X. Shao, B. Jiao, and R. Zhang, “Polarforming for wireless networks: Opportunities and challenges,” 2025. [Online]. Available: https://arxiv.org/abs/2505.20760

Paper details

vlnc:W_drc8qsv4
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 13

downloads · 2

A view counts once per browser per day, a download each time the PDF is requested.

  • Computer Science

Not recorded for this paper

View statement
Looking for related papers…
Contents