betaFeedback

WorksPhysics and Astronomy

Fluid viscoelasticity controls acoustic streaming via shear waves

Abstract

Control of acoustic streaming can significantly impact fluid and particle transport in microfluidics. We report enhancement, suppression, and reversal of acoustic streaming inside a rectangular microchannel by controlling the fluid viscoelastic properties. Our study reveals that the streaming regimes depend on Deborah number (DeDe) and viscous diffusion number (DvDv), expressed in terms of a Streaming Coefficient (CsC_s). We find streaming is enhanced when Cs>1C_s>1, suppressed for 0≤Cs≤10\leq C_s\leq1, and reversed when Cs<0C_s<0. We explain the regimes in terms of the interplay between the Reynolds and viscoelastic stresses that collectively drive fluid motion. Remarkably, we discover the role of viscoelastic shear waves in acoustic streaming transition characterized by the ratio of acoustic attenuation length and shear wavelength. We gain deeper insight into the streaming transition by examining energy dynamics in terms of the loss and storage moduli. Our study may find applications in acousto-microfluidics systems for particle handling and fluid pumping/mixing.

Introduction

Oscillatory motion in a fluid, driven by acoustic waves or vibrating boundaries, produces a steady flow known as acoustic streaming [10, 9, 26, 24] (Lighthill 1978). This nonlinear effect stems from the dissipation of acoustic energy (Lighthill 1978) and arises through two primary mechanisms. In large-scale systems, where dimensions far exceed the acoustic wavelength, bulk attenuation of traveling waves leads to “quartz wind” [9]. In contrast, in small-scale systems, energy dissipation within a thin boundary layer gives rise to “boundary layer-driven streaming” [26, 24]. The vorticity generated within the boundary layer, known as “inner streaming” or “Schlichting streaming” [26], drives counter-rotating vortices in the bulk fluid, referred to as “outer streaming” or “Rayleigh streaming” [24]. Boundary-layer-driven streaming has gained attention in acousto-microfluidic systems for applications in pumping, mixing, and particle/cell manipulation [31, 25]. In such systems, acoustic waves at MHz frequencies generate acoustic radiation forces (ARF) [6] in addition to streaming effects [17]. ARF align suspended particles while streaming, governed by the Stokes drag, tend to disorganize them, particularly at the submicron scale [6, 17]. Suppression of streaming can greatly benefit the focusing and sorting of submicron particles such as viruses, bacteria, and exosomes for medical diagnostics [29]. On the other hand, enhanced streaming is crucial for overcoming low Reynolds number constraints to improve fluid mixing and pumping [31]. Thus, achieving effective streaming control is critical in acousto-microfluidic systems. Existing streaming suppression methods rely on fluid inhomogeneity [13] or shape-optimized channels [2], while streaming enhancement has been achieved using thermal gradients [23]; however, these strategies are difficult to implement and offer limited control. Currently, no method enables both suppression and enhancement of acoustic streaming in single-fluid microchannel systems, and none enables its directional reversal. This underscores the need for a simple and effective alternative approach to address a critical gap in the field. Prior studies have examined acoustic streaming in viscoelastic (VE) fluids around a particle [7] and in a narrow channel of depth comparable to the boundary layer thickness [30]. In this study, we report the enhancement, suppression, and reversal of acoustic streaming in a typical rectangular microchannel by tuning the fluid viscoelasticity. More importantly, we take a profound approach to elucidate the physics underlying acoustic streaming control in terms of relevant timescales, stresses, and viscoelastic shear waves [27, 11, 21, 20].

This study considers a glass–silicon–glass microchannel of width WW and depth DD, shown in Figure 1. The rectangular channel is filled with a viscoelastic fluid characterized by a total viscosity μ=μp+μs\mu= \mu_p + \mu_s, where μp\mu_p and μs\mu_s denote the polymeric and solvent contributions, respectively, and a relaxation time τ\tau. Actuation of the piezoelectric transducer generates a standing acoustic wave along the channel width (along XX-axis), corresponding to a half-wave resonance condition, W=λ0/2W = \lambda_0/2, where λ0\lambda_0 is the wavelength of the standing wave as illustrated in Figure 1(a). This acoustic excitation perturbs the fluid, inducing spatial variations in the pressure pp, density ρ\rho, and velocity field v\mathbf{v} [6]. To describe the response of the viscoelastic medium under such excitation, the Oldroyd-B constitutive model [19] is used.

Image not extracted

Figure 1. A sketch of the section of viscoelastic fluid and stationary channel wall with acoustic boundary layer formation. The bulk fluid supports a horizontal 1-D standing sinusoidal pressure wave of wavelength λ0\lambda_0 along the xx axis of channel. The interaction between oscillating viscoelastic fluid and the stationary wall forms a acoustic boundary layer closed to the wall, represented by δve\delta_{ve}, indicate the short range fluid region with an incompressible solenoidal flow. The region away from the δve\delta_{ve} is long range field with compressible potential flow, represented by dd. Using Helmholtz decomposition the total first order fluid velocity is consider as v1=v1d+v1δ\mathbf{v}_1 = \mathbf{v}_1^d + \mathbf{v}_1^\delta. A schematic variation of v1d\mathbf{v}_1^d (red), v1δ\mathbf{v}_1^\delta (blue) and v1\mathbf{v}_1 (black) is shown with arrows, which indicate the direction of field.

Theoretical formulation

Viscoelastic fluid modeling and perturbations

To analyze the characteristics of acoustic streaming in a viscoelastic fluid, the formulation begins with the fundamental governing equations, the continuity and momentum equations. The present framework is restricted to dilute polymer solutions for which shear-thinning effects are negligible. Under these conditions, the Oldroyd-B constitutive model [19] is employed, as it provides a minimal yet effective description of fluids exhibiting both viscous and elastic responses. This model has been widely used to represent the rheological behavior of dilute polymer solutions and biological fluids in acoustofluidic and related flow configurations (Doinikov et al. 2021a,b; Sujith et al. 2024; Vargas et al. 2022). Accordingly, the governing equations for a viscoelastic fluid are expressed as follows:

∂ρ∂t+∇⋅(ρv)=0(1)\frac{\partial\rho}{\partial t} + \nabla\cdot(\rho\mathbf{v}) = 0 \tag*{(1)}

and

ρ(∂v∂t+v⋅∇v)=−∇p+∇⋅μs[∇v+(∇v)T−23(∇⋅v)I]+∇⋅σ.(2)\rho\left(\frac{\partial\mathbf{v}}{\partial t}+\mathbf{v}\cdot\nabla\mathbf{v}\right)=-\nabla p+\nabla\cdot\mu_s\left[\nabla\mathbf{v}+(\nabla\mathbf{v})^{\mathrm{T}}-\frac{2}{3}(\nabla\cdot\mathbf{v})\mathbf{I}\right]+\nabla\cdot\boldsymbol{\sigma}. \tag*{(2)}

The fluid velocity is expressed as v=vxex+vyey\mathbf{v}=v_x\mathbf{e}_x+v_y\mathbf{e}_y, where ex\mathbf{e}_x and ey\mathbf{e}_y are unit vectors along the xx and yy directions, and μs\mu_s denotes the solvent viscosity. In Eq. (2), consistent with Refs. Doinikov et al. [7]; Vargas et al. [30], for dilute polymer solutions used in the present work, acoustic energy dissipation is dominated by shear viscosity, particularly in Rayleigh streaming near solid boundaries. Accordingly, the role of bulk viscosity is taken to be negligible. For concentrated polymer solutions, however, frequency-dependent bulk viscosity may become relevant, highlighting the need for improved experimental techniques and offering a potential avenue for future investigation.

In Eq. (2), σ\boldsymbol{\sigma} represents the viscoelastic stress tensor corresponds to the Oldroyd-B model (Oldroyd [19]), and is given by

σ∇+σ=μp[∇v+(∇v)T−23(∇⋅v)I].(3)\overset{\nabla}{\boldsymbol{\sigma}}+\boldsymbol{\sigma}=\mu_p\left[\nabla\mathbf{v}+(\nabla\mathbf{v})^{\mathrm{T}}-\frac{2}{3}(\nabla\cdot\mathbf{v})\mathbf{I}\right]. \tag*{(3)}

Here, μp\mu_p denotes the polymer viscosity, τ\tau is the relaxation time, and σ∇\overset{\nabla}{\boldsymbol{\sigma}} stands for the upper-convected stress derivative of σ\boldsymbol{\sigma}, defined as

σ∇=∂σ∂t+v⋅∇σ−(∇v)T⋅σ−σ⋅∇v,(4)\overset{\nabla}{\boldsymbol{\sigma}}=\frac{\partial\boldsymbol{\sigma}}{\partial t}+\mathbf{v}\cdot\nabla\boldsymbol{\sigma}-(\nabla\mathbf{v})^{\mathrm{T}}\cdot\boldsymbol{\sigma}-\boldsymbol{\sigma}\cdot\nabla\mathbf{v}, \tag*{(4)}

which ensures the frame invariance in the constitutive description of viscoelastic fluids.

To examine fluid fluctuations driven by the acoustic field, a perturbation approach is applied to the governing equations. The relevant fluid variables, density ρ\rho, pressure pp, velocity v\mathbf{v}, and stress tensor σ\boldsymbol{\sigma}, are expressed as asymptotic expansions in a small perturbation parameter and retained up to second order (Bruus [5]; Powell [22]; Sujith et al. [28]). Substitution of these expansions into the governing equations, followed by collection of terms of equal order, yields a hierarchy of equations. At first order, only linear terms are retained, while all nonlinear products of first-order quantities are neglected. This first-order governing equations can be written as

∂ρ1∂t+ρ0∇⋅v1=0(5)\frac{\partial\rho_1}{\partial t}+\rho_0\nabla\cdot\mathbf{v}_1=0 \tag*{(5)}
ρ0∂v1∂t=−∇p1+∇⋅μs[∇v1+(∇v1)T−23(∇⋅v1)I]+∇⋅σ1(6)\rho_0\frac{\partial\mathbf{v}_1}{\partial t}=-\nabla p_1+\nabla\cdot\mu_s\left[\nabla\mathbf{v}_1+(\nabla\mathbf{v}_1)^{T}-\frac{2}{3}(\nabla\cdot\mathbf{v}_1)\mathbf{I}\right]+\nabla\cdot\boldsymbol{\sigma}_1 \tag*{(6)}

and

τ∂σ1∂t+σ1=μp[∇v1+(∇v1)T−23(∇⋅v1)I].(7)\tau\frac{\partial\boldsymbol{\sigma}_1}{\partial t}+\boldsymbol{\sigma}_1=\mu_p\left[\nabla\mathbf{v}_1+(\nabla\mathbf{v}_1)^{T}-\frac{2}{3}(\nabla\cdot\mathbf{v}_1)\mathbf{I}\right]. \tag*{(7)}

Moreover, the equation of state can be expressed as

p1−p0=(ρ1−ρ0)c02.(8)p_1-p_0=(\rho_1-\rho_0)c_0^2. \tag*{(8)}

Here, p0p_0, ρ0\rho_0 are equilibrium pressure and density, c0c_0 represents the speed of sound in the fluid. The harmonic time dependence for the first-order fields is expressed as ρ1=ρ^1(r)eiωt\rho_1=\hat{\rho}_1(\mathbf{r})e^{i\omega t}, p1=p^1(r)eiωtp_1=\hat{p}_1(\mathbf{r})e^{i\omega t}, v1=v^1(r)eiωt\mathbf{v}_1=\hat{\mathbf{v}}_1(\mathbf{r})e^{i\omega t}, and σ1=σ^1(r)eiωt\boldsymbol{\sigma}_1=\hat{\boldsymbol{\sigma}}_1(\mathbf{r})e^{i\omega t} [7, 28]. Here, ω=2πf\omega=2\pi f is the angular frequency, where ff denotes the resonant frequency of the standing bulk acoustic wave (S-BAW). The quantities ρ^1\hat{\rho}_1, p^1\hat{p}_1, v^1\hat{\mathbf{v}}_1, σ^1\hat{\boldsymbol{\sigma}}_1 represent the time-independent spatial amplitudes of the first-order fields. Henceforth, the notation “ ^\hat{\ }” is used to indicate these time-independent amplitudes. Substituting this harmonic form into Eqs. (5)–(7) transforms the first-order equations from the time domain to the frequency domain. Upon simplification, the first-order equations becomes

iωρ^1+ρ0∇⋅v^1=0(9)i\omega\hat{\rho}_1+\rho_0\nabla\cdot\hat{\mathbf{v}}_1=0 \tag*{(9)}

and

ρ0∂v^1∂t=−∇p^1+∇⋅μc[∇v^1+(∇v^1)T−23(∇⋅v^1)I],(10)\rho_0\frac{\partial\hat{\mathbf{v}}_1}{\partial t}=-\nabla\hat{p}_1+\nabla\cdot\mu_c\left[\nabla\hat{\mathbf{v}}_1+(\nabla\hat{\mathbf{v}}_1)^{T}-\frac{2}{3}(\nabla\cdot\hat{\mathbf{v}}_1)\mathbf{I}\right], \tag*{(10)}

respectively, where

μc=μs+μp1+iωλ.(11)\mu_c=\mu_s+\frac{\mu_p}{1+i\omega\lambda}. \tag*{(11)}

Here, μc\mu_c is the complex viscosity, which describes the effect of viscoelastic parameters on the first-order fluid field.

The first-order fields are purely oscillatory and therefore do not contribute to time-averaged quantities [6]. In contrast, the second-order fields generate a finite time-averaged response. Retaining terms up to second order in the perturbation expansions of Eqs. (1)–(4), followed by temporal averaging over one acoustic period, yields the governing equations for the time-averaged second-order fields, expressed as

ρ0∇⋅⟨v2⟩=−∇⋅⟨ρ1v1⟩(12)\rho_0\nabla\cdot\langle\mathbf{v}_2\rangle=-\nabla\cdot\langle\rho_1\mathbf{v}_1\rangle \tag*{(12)}

and

ρ0⟨v1⋅∇v1+v1∇⋅v1⟩=−∇⟨p2⟩+μ∇2⟨v2⟩+μ3∇(∇⋅⟨v2⟩)−τ∇⋅⟨v1⋅∇σ1⟩+τ∇⋅⟨(∇v1)T⋅σ1⟩+τ∇⋅⟨σ1⋅∇v1⟩.(13)\begin{aligned} \rho_0\langle\mathbf{v}_1\cdot\nabla\mathbf{v}_1+\mathbf{v}_1\nabla\cdot\mathbf{v}_1\rangle ={}&-\nabla\langle p_2\rangle+\mu\nabla^2\langle\mathbf{v}_2\rangle+\frac{\mu}{3}\nabla(\nabla\cdot\langle\mathbf{v}_2\rangle)\\ &-\tau\nabla\cdot\langle\mathbf{v}_1\cdot\nabla\boldsymbol{\sigma}_1\rangle+\tau\nabla\cdot\langle(\nabla\mathbf{v}_1)^T\cdot\boldsymbol{\sigma}_1\rangle+\tau\nabla\cdot\langle\boldsymbol{\sigma}_1\cdot\nabla\mathbf{v}_1\rangle. \tag*{(13)} \end{aligned}

The final three terms on the right-hand side of Eq. (13) arise from the viscoelastic constitutive model and represent additional body forces introduced by the fluid’s viscoelastic nature.

Analytical form of boundary-layer driven streaming

The analysis is restricted to the cross-section of the microchannel (see Figure 1), where the streaming flow is assumed to be two-dimensional in the XX-YY plane and uniform along the channel axis (ZZ-direction). The channel width is selected as half of the ultrasonic wavelength, ensuring a resonant configuration that produces a one-dimensional standing acoustic wave along the XX-axis. The first-order acoustic velocity field is expressed as v1=v^1eiωt\mathbf{v}_1 = \hat{\mathbf{v}}_1 e^{i\omega t}, with v^1=Aωcos⁡(kXX)eX\hat{\mathbf{v}}_1 = A\omega\cos(k_X X)\mathbf{e}_X, where AA denotes the amplitude of wall displacement.

In the vicinity of the channel walls, the oscillatory velocity attenuates due to viscous dissipation and fluid–solid interaction, consistent with the no-slip boundary condition. This attenuation occurs over a characteristic length scale δve\delta_{ve}, which defines the thickness of the viscoelastic acoustic boundary layer. The problem involves multiple length scales, including the oscillation amplitude AA, channel width WW, channel depth DD, boundary-layer thickness δve\delta_{ve}, and acoustic wavelength λ0\lambda_0. For typical acoustofluidic systems, these scales satisfy the ordering A≪δve≪λ0∼W∼DA \ll\delta_{ve} \ll\lambda_0 \sim W \sim D. Accordingly, the Stokes parameter is defined as Sp=δve/λ0≪1S_p = \delta_{ve}/\lambda_0 \ll1, and the thin-boundary-layer assumption δve/D≪1\delta_{ve}/D \ll1 is adopted.

A standard method for addressing such problem is through boundary-layer theory, which divides the domain into a bulk region and a thin boundary layer near solid surfaces. The first-order velocity is solved in each region and matched asymptotically. Given that δve≪λ0\delta_{ve} \ll\lambda_0, the boundary-layer flow is often assumed incompressible. However, this assumption is only partially valid: the flow is incompressible in the wall-normal direction due to the short scale δve\delta_{ve}, but remains compressible along the wall, where variations occur over the longer scale λ0\lambda_0, similar to the bulk. Full incompressibility is valid only in specific cases, such as flow around particles of size a≪λ0a \ll\lambda_0, where both aa and δve\delta_{ve} determine the spatial dynamics [6]. To address this limitation, a refined modeling approach is considered [1], where the field is decomposed into components, which explicitly identify compressible and incompressible components throughout the domain, enabling a more accurate and complete representation of the flow. As a starting point of the study, the Helmholtz decomposition of the first order velocity field is consider as

v1=v1d+v1δ.(14)\mathbf{v}_1 = \mathbf{v}_1^d + \mathbf{v}_1^\delta. \tag*{(14)}

Here, v1d\mathbf{v}_1^d represents the compressible, irrotational (potential) flow, satisfying ∇×v1d=0\nabla\times\mathbf{v}_1^d = 0, while v1δ\mathbf{v}_1^\delta denotes the incompressible, solenoidal flow, with ∇⋅v1δ=0\nabla\cdot\mathbf{v}_1^\delta= 0. Moreover, v1d=v^1deiωt\mathbf{v}_1^d = \hat{\mathbf{v}}_1^d e^{i\omega t}, v1δ=v^1δeiωt\mathbf{v}_1^\delta= \hat{\mathbf{v}}_1^\delta e^{i\omega t}, the time-independent spatial amplitudes are denoted by v^1d\hat{\mathbf{v}}_1^d and v^1δ\hat{\mathbf{v}}_1^\delta, respectively. The superscripts “dd” and “δ\delta” refer to the bulk and boundary layer regions, as illustrated in Figure 1(b). Applying Eq. (14) in Eqs. (9) and (10), followed by separating the irrotational and solenoidal and further simplification using Eq. (8) gives

iωκ0p^1=−∇⋅v^1d,(15)i\omega\kappa_0\hat{p}_1=-\nabla\cdot\hat{\mathbf{v}}_1^d, \tag*{(15)}
iωρ0v^1d=−γ∇p^1,where γ=(1+43iωκ0μc)(16)i\omega\rho_0\hat{\mathbf{v}}_1^d=-\gamma\nabla\hat{p}_1,\qquad\text{where }\gamma=\left(1+\frac{4}{3}i\omega\kappa_0\mu_c\right) \tag*{(16)}

and

iωρ0v^1δ=μc∇2v^1δ.(17)i\omega\rho_0\hat{\mathbf{v}}_1^\delta=\mu_c\nabla^2\hat{\mathbf{v}}_1^\delta. \tag*{(17)}

Here, κ0=1/ρ0c02\kappa_0=1/\rho_0c_0^2, from Eqs. (15), (16) and (17), the Helmholtz equation for p1p_1, v1d\mathbf{v}_1^d, and v1δ\mathbf{v}_1^\delta can be expressed as

∇2p^1+kd2p^1=0,(18)\nabla^2\hat{p}_1+k_d^2\hat{p}_1=0, \tag*{(18)}
∇2v^1d+kd2v^1d=0,(19)\nabla^2\hat{\mathbf{v}}_1^d+k_d^2\hat{\mathbf{v}}_1^d=0, \tag*{(19)}

and

∇2v^1d−ks2v^1d=0.(20)\nabla^2 \hat{\mathbf{v}}_1^d-k_s^2\hat{\mathbf{v}}_1^d=0. \tag*{(20)}

The wave numbers kdk_d and ksk_s are given by

kd=kxγ1/2andks=(iωρ0μc)1/2.(21)k_d=\frac{k_x}{\gamma^{1/2}} \quad\text{and}\quad k_s=\left(\frac{\mathrm{i}\omega\rho_0}{\mu_c}\right)^{1/2}. \tag*{(21)}

Here, kx=2π/λ0k_x=2\pi/\lambda_0 denotes the acoustic wavenumber, while ksk_s is the complex shear wavenumber associated with the viscoelastic fluid. Drawing an analogy with viscous fluids, the acoustic boundary layer thickness for a viscoelastic fluid is defined as δve=1/Im⁡[ks]\delta_{ve}=1/\operatorname{Im}[k_s], and the corresponding shear wavelength as λve=2π/Re⁡[ks]\lambda_{ve}=2\pi/\operatorname{Re}[k_s]. For a Newtonian fluid, the ratio λve/δve\lambda_{ve}/\delta_{ve} reduces to λv/δ=2π\lambda_v/\delta=2\pi, whereas for a viscoelastic fluid, this ratio generally deviates from 2π2\pi, λve/δve≢2π\lambda_{ve}/\delta_{ve}\not\equiv2\pi ([7, 28]). Since acoustic streaming is driven by boundary layer dynamics, the modified boundary layer thickness and shear wavelength are used throughout the subsequent analysis.

Initially the inner boundary layer streaming is solved to find out a slip velocity condition for outer streaming, which is outlined in the upcoming sections. In Eq. (20) the Laplacian operator ∇2=∂x2+∂y2\nabla^2=\partial_x^2+\partial_y^2. In the boundary layer region, as shown in Figure 1(b), from scaling ∂x∼kx=2π/λ\partial_x\sim k_x=2\pi/\lambda and ∂y∼1/δve\partial_y\sim1/\delta_{ve}, where the derivatives along the standing wave direction (xx-axis) is very less as compared to the yy direction in the boundary layer, therefore this study approximate ∇2≈∂y2\nabla^2\approx\partial_y^2 ([1]). Accordingly, Eq. (20) for xx component of v^1d\hat{\mathbf{v}}_1^d reduces to

∂y2v^1,xd=ks2v^1,xd.(22)\partial_y^2\hat{v}_{1,x}^d=k_s^2\hat{v}_{1,x}^d. \tag*{(22)}

Double integration of Eq. (22) gives

v^1,xd=c1eksy+c2e−ksy,(23)\hat{v}_{1,x}^d=c_1e^{k_sy}+c_2e^{-k_sy}, \tag*{(23)}

where c1c_1 and c2c_2 are constants of integration. A long range boundary condition is applied: when y→∞y\to\infty, v^1,xd→0\hat{v}_{1,x}^d\to0 and no-slip boundary condition: at y=0y=0, v1=0\mathbf{v}_1=0 (where v^1,xd=−v^1d\hat{v}_{1,x}^d=-\hat{v}_1^d) on Eq. (23). Which gives

v^1,xd=−v^1de−ksy.(24)\hat{v}_{1,x}^d=-\hat{v}_1^d e^{-k_sy}. \tag*{(24)}

Here, the irrotational far field first order velocity field is considered as v1d=v1d0cos⁡(kxx)ex\mathbf{v}_1^d=v_1^{d0}\cos(k_xx)\mathbf{e}_x. Where v1d0v_1^{d0} is the amplitude of first order velocity perturbation, v1d0=Aωv_1^{d0}=A\omega. Substitution of Eq. (11) to ksk_s and further expansion and simplification of Eq. (24) yields to

v^1,xd=−v1d0cos⁡(kxx)e−χy/δfe−iξy/δf.(25)\hat{v}_{1,x}^d=-v_1^{d0}\cos(k_xx)e^{-\chi y/\delta_f}e^{-\mathrm{i}\xi y/\delta_f}. \tag*{(25)}

Here, δf=2μf/ρω\delta_f=\sqrt{2\mu_f/\rho\omega}, subscript “ff” indicate the base Newtonian fluid, considered as Deionized water, χ\chi and ξ\xi can be expressed as

χ=Γ2+Ξ2+Γ,ξ=Γ2+Ξ2−Γ.(26)\chi=\sqrt{\Gamma^2+\Xi^2+\Gamma},\quad \xi=\sqrt{\Gamma^2+\Xi^2-\Gamma}. \tag*{(26)}

The parameters Γ\Gamma and Ξ\Xi encapsulate the influence of the fluid’s viscoelasticity and are expressed in terms of dimensionless quantities derived from relevant time scales. To systematically characterize the viscoelastic behavior, four fundamental time scales are considered: the acoustic time tac=1/ωt_{ac}=1/\omega, the polymer relaxation time τ\tau, the polymer viscous diffusion time td,p=(D/2)2/2νpt_{d,p}=(D/2)^2/2\nu_p, and the solvent viscous diffusion time td,s=(D/2)2/2νst_{d,s}=(D/2)^2/2\nu_s. Here, ω=2πf\omega=2\pi f is the angular frequency of the acoustic field, while νp\nu_p and νs\nu_s denote the kinematic viscosities of the polymer and solvent, respectively. The interplay between these time scales is captured using two key dimensionless groups: the Deborah number, De=τ/tacDe = \tau/t_{ac}, which quantifies the relative importance of elastic to acoustic time scales, and the viscous diffusion number, Dv=td,s/td,p=νp/νsDv = t_{d,s}/t_{d,p} = \nu_p/\nu_s, which compares the diffusive behavior of polymer and solvent viscosity components. Additionally, the dimensionless solvent viscosity is defined as μs∗=μs/μf\mu_s^* = \mu_s/\mu_f, where μf\mu_f is the viscosity of the base Newtonian fluid used as a reference. Finally, Γ\Gamma and Ξ\Xi can be expressed as

Γ=−1μs∗{Dv DeDv2+2Dv+(1+De2)}.(27)\Gamma= -\frac{1}{\mu_s^*}\left\{\frac{Dv\,De}{Dv^2+2Dv+(1+De^2)}\right\}. \tag*{(27)}

and

Ξ=1μs∗{Dv+1+De2Dv2+2Dv+(1+De2)}.(28)\Xi= \frac{1}{\mu_s^*}\left\{\frac{Dv+1+De^2}{Dv^2+2Dv+(1+De^2)}\right\}. \tag*{(28)}

As mentioned before, from incompressible solenoidal flow inside the boundary layer ∇⋅v1δ=0\nabla\cdot\mathbf{v}_1^\delta= 0. Using this along with the no slip boundary condition at the surface v^1,yδ=0\hat{v}_{1,y}^\delta= 0, the yy component of first order velocity field inside the boundary layer is obtained,

v^1,yδ=−χ−iξχ2+ξ2v1d0δfkxsin⁡(kxx)(1−e−χy/δfe−iξy/δf).(29)\hat{v}_{1,y}^\delta= -\frac{\chi-i\xi}{\chi^2+\xi^2}v_1^{d0}\delta_f k_x\sin(k_xx)\left(1-e^{-\chi y/\delta_f}e^{-i\xi y/\delta_f}\right). \tag*{(29)}

Considering equations Eqs. (14), (25), and (29); the total first order velocity solutions becomes

v1,x=v1d0cos⁡(kxx)(1−e−χy/δfe−iξy/δf)eiωt(30)v_{1,x}=v_1^{d0}\cos(k_xx)\left(1-e^{-\chi y/\delta_f}e^{-i\xi y/\delta_f}\right)e^{i\omega t} \tag*{(30)}

and

v1,y=−χ−iξχ2+ξ2v1d0δfkxsin⁡(kxx)(1−e−χy/δfe−iξy/δf)eiωt.(31)v_{1,y}=-\frac{\chi-i\xi}{\chi^2+\xi^2}v_1^{d0}\delta_f k_x\sin(k_xx)\left(1-e^{-\chi y/\delta_f}e^{-i\xi y/\delta_f}\right)e^{i\omega t}. \tag*{(31)}

Here, δfkx≪1\delta_f k_x \ll1, therefore, the yy-component of the first-order velocity, v^1,yδ\hat{v}_{1,y}^\delta and v1,yv_{1,y} becomes negligible as compared to the xx-component.

To analyze acoustic streaming, second-order fluid fields is decomposed into two distinct components corresponding to their characteristic spatial scales: a boundary layer component governed by the length scale δve\delta_{ve}, and a bulk component associated with D∼O(λ0)D \sim O(\lambda_0). The short-range boundary layer field is denoted by f2δ\mathbf{f}_2^\delta, and the long-range bulk fields by f2d\mathbf{f}_2^d [1] and ϵ=δ/d≪1\epsilon= \delta/d \ll1. The total second-order field is then expressed as the sum of these contributions,

f2=f2d+f2δ.(32)\mathbf{f}_2=\mathbf{f}_2^d+\mathbf{f}_2^\delta. \tag*{(32)}

Substitution of Eq. (32) for second order pressure, velocity, and stress in Eqs. (12) and (13) and separating short range field terms yields to

ρ0∇⋅⟨v2δ⟩=−∇⋅⟨ρ1v1δ⟩(33)\rho_0\nabla\cdot\langle\mathbf{v}_2^\delta\rangle=-\nabla\cdot\langle\rho_1\mathbf{v}_1^\delta\rangle \tag*{(33)}

and

ρ0∇⋅⟨v1δv1δ+v1δv1d+v1dv1δ⟩=−∇⟨p2δ⟩+μ∇2⟨v2δ⟩+μ3∇(∇⋅⟨v2δ⟩)−τ∇⋅⟨v1δ⋅∇σ1⟩+τ∇⋅⟨((∇v1δ)T⋅σ1)⟩+τ∇⋅⟨σ1⋅∇v1δ⟩.(34)\begin{aligned} \rho_0\nabla\cdot\left\langle\mathbf{v}_1^\delta\mathbf{v}_1^\delta+\mathbf{v}_1^\delta\mathbf{v}_1^d+\mathbf{v}_1^d\mathbf{v}_1^\delta\right\rangle ={}&-\nabla\langle p_2^\delta\rangle+\mu\nabla^2\langle\mathbf{v}_2^\delta\rangle+\frac{\mu}{3}\nabla\left(\nabla\cdot\langle\mathbf{v}_2^\delta\rangle\right)\\ &-\tau\nabla\cdot\left\langle\mathbf{v}_1^\delta\cdot\nabla\boldsymbol{\sigma}_1\right\rangle+\tau\nabla\cdot\left\langle\left((\nabla\mathbf{v}_1^\delta)^T\cdot\boldsymbol{\sigma}_1\right)\right\rangle+\tau\nabla\cdot\left\langle\boldsymbol{\sigma}_1\cdot\nabla\mathbf{v}_1^\delta\right\rangle. \tag*{(34)} \end{aligned}

To gain insight into the relative significance of the terms in Eq. (34), a scaling analysis is performed. As a first step, the initial focus is on the pressure component p2δp_2^\delta by taking the divergence of Eq. (34). This expression is then simplified using Eqs. (33) and (15), along with the incompressibility condition ∇⋅v1δ=0\nabla\cdot\mathbf{v}_1^\delta=0. The resulting equation for p2δp_2^\delta can be written as

∇2⟨p2δ⟩=−ρ0∇⋅(∇⋅⟨v1δv1δ⟩+∇⋅⟨v1δv1d⟩+∇⋅⟨v1dv1δ⟩)+43iωμkd2∇2⟨v1δ⋅v1d⟩−τ∇⋅(∇⋅⟨v1δ⋅∇σ1⟩+∇⋅⟨(∇v1δ)T⋅σ1⟩+∇⋅⟨σ1⋅∇v1δ⟩)(35)\nabla^2\langle p_2^\delta\rangle=-\rho_0\nabla\cdot\left(\nabla\cdot\langle v_1^\delta v_1^\delta\rangle+\nabla\cdot\langle v_1^\delta v_1^d\rangle+\nabla\cdot\langle v_1^d v_1^\delta\rangle\right)+\frac{4}{3i\omega}\mu k_d^2\nabla^2\langle v_1^\delta\cdot v_1^d\rangle- \tau\nabla\cdot\left(\nabla\cdot\langle v_1^\delta\cdot\nabla\sigma_1\rangle+\nabla\cdot\left\langle\left(\nabla v_1^\delta\right)^{T}\cdot\sigma_1\right\rangle+\nabla\cdot\langle\sigma_1\cdot\nabla v_1^\delta\rangle\right) \tag*{(35)}

In Eq. (35), the first, second, and third terms on the right-hand side arise from Reynolds stress (RES), viscous stress (V), and viscoelastic stress (VES), respectively. These contributions are denoted as TREST_{\mathrm{RES}}, TVT_{\mathrm{V}}, and TVEST_{\mathrm{VES}}. To estimate their magnitudes, the following scalings are applied:

∣v1,xδ∣→v1d0,∣v1,yδ∣→ϵv1d0,∣v1,xd∣→v1d0,∣v1,yd∣→0,∣v1,x∣→v1d0,∣v1,y∣→ϵv1d0(36)|v_{1,x}^{\delta}|\to v_1^{d0},\quad|v_{1,y}^{\delta}|\to\epsilon v_1^{d0},\quad|v_{1,x}^{d}|\to v_1^{d0},\quad|v_{1,y}^{d}|\to0,\quad|v_{1,x}|\to v_1^{d0},\quad|v_{1,y}|\to\epsilon v_1^{d0} \tag*{(36)}

where ϵ=δ/d≪1\epsilon=\delta/d\ll1. Based on the dominant contributions, the leading-order scalings of the terms are:

∣TRES∣∼ρ0d−2(v1d0)2,∣TV∣∼μω(δd)−2(v1d0)2,∣TVES∣∼τμ(δd)−2(v1d0)2.(37)|T_{\mathrm{RES}}|\sim\rho_0d^{-2}(v_1^{d0})^2,\quad|T_{\mathrm{V}}|\sim\frac{\mu}{\omega}(\delta d)^{-2}(v_1^{d0})^2,\quad|T_{\mathrm{VES}}|\sim\tau\mu(\delta d)^{-2}(v_1^{d0})^2. \tag*{(37)}

The scaling of the second-order pressure term yields: ∣∇2⟨p2δ⟩∣∼δ−2p2δ|\nabla^2\langle p_2^\delta\rangle|\sim\delta^{-2}p_2^\delta. By equating both sides of Eq. (35), the scaling for the pressure can be obtained as

∣p2δ∣∼ϵ2ρ0(v1d0)2,μωd−2(v1d0)2,τμd−2(v1d0)2.(38)|p_2^\delta|\sim\epsilon^2\rho_0(v_1^{d0})^2,\quad\frac{\mu}{\omega}d^{-2}(v_1^{d0})^2,\quad\tau\mu d^{-2}(v_1^{d0})^2. \tag*{(38)}

Since d−2d^{-2} and ϵ\epsilon are small, the pressure gradient ∇p2δ\nabla p_2^\delta becomes negligible and is omitted from further analysis of the boundary layer in Eq. (34). Additionally, the term (μ/3)∇(∇⋅⟨v2δ⟩)(\mu/3)\nabla(\nabla\cdot\langle\mathbf{v}_2^\delta\rangle) in Eq. (34) simplifies to (μ/3ρ0)∇⟨v1δ⋅∇ρ1⟩(\mu/3\rho_0)\nabla\langle\mathbf{v}_1^\delta\cdot\nabla\rho_1\rangle, which scales as: μd−2(v1d0)2/3c0\mu d^{-2}(v_1^{d0})^2/3c_0, which is very less than ∣μ∇⟨v2δ⟩∣∼μδ−2(v1d0)2/c0|\mu\nabla\langle\mathbf{v}_2^\delta\rangle|\sim\mu\delta^{-2}(v_1^{d0})^2/c_0 ([1]). Therefore, further simplification and rearrangement of Eq. (34) gives

μ∇2⟨v2δ⟩=ρ0∇⋅⟨v1δv1δ+v1δv1d+v1dv1δ⟩+τ∇⋅⟨v1δ⋅∇σ1⟩−τ∇⋅⟨(∇v1δ)T⋅σ1⟩−τ∇⋅⟨σ1⋅∇v1δ⟩.(39)\mu\nabla^2\langle\mathbf{v}_2^\delta\rangle=\rho_0\nabla\cdot\langle v_1^\delta v_1^\delta+v_1^\delta v_1^d+v_1^d v_1^\delta\rangle+\tau\nabla\cdot\langle v_1^\delta\cdot\nabla\sigma_1\rangle -\tau\nabla\cdot\left\langle\left(\nabla v_1^\delta\right)^T\cdot\sigma_1\right\rangle-\tau\nabla\cdot\langle\sigma_1\cdot\nabla v_1^\delta\rangle. \tag*{(39)}

From Eq. (39) an analytical solution of ⟨v2,xδ⟩\langle v_{2,x}^\delta\rangle can be obtain by integrating it twice and by implying the boundary conditions y→∞y\to\infty, ⟨v2,xδ⟩→0\langle v_{2,x}^\delta\rangle\to0, ∂⟨v2,xδ⟩/∂y→0\partial\langle v_{2,x}^\delta\rangle/\partial y\to0. Here ∇2≈∂y2\nabla^2\approx\partial_y^2, therefore the component of time averaged second order streaming velocity along the standing wave becomes

⟨v2,xδ⟩=−38(v1d0)2c0sin⁡[2kxx]13(1+De2)μs(Dv+1)χ2(χ2+ξ2)2e−2χy/δf{ξ(χ2+ξ2)J1+2eχy/δfχ2J2cos⁡[ξy/δf]−2eχy/δfχ2J3sin⁡[ξy/δf]}.(40)\langle v_{2,x}^\delta\rangle=-\frac{3}{8}\frac{(v_1^{d0})^2}{c_0}\sin[2k_xx]\frac{1}{3(1+De^2)\mu_s(Dv+1)\chi^2(\chi^2+\xi^2)^2}e^{-2\chi y/\delta_f} \left\{\xi(\chi^2+\xi^2)J_1+2e^{\chi y/\delta_f}\chi^2J_2\cos[\xi y/\delta_f]-2e^{\chi y/\delta_f}\chi^2J_3\sin[\xi y/\delta_f]\right\}. \tag*{(40)}

Here J1J_1, J2J_2 and J3J_3 can be defined as

J1=2De μsDv ξ(δf2kx2+χ2−ξ2)+δf2ρ0ωξ+De2{−4μsDvχ3+δf2(4kx2μsDvχ+ρ0ωξ)}.(41)J_1=2De\ \mu_sDv\ \xi(\delta_f^2k_x^2+\chi^2-\xi^2)+\delta_f^2\rho_0\omega\xi+ De^2\left\{-4\mu_sDv\chi^3+\delta_f^2(4k_x^2\mu_sDv\chi+\rho_0\omega\xi)\right\}. \tag*{(41)}
J2=DeμsDν(χ4+4δf2kx2ξ2−ξ4)−2δf2ρ0ω(χ2−2ξ2)+De2{2μsDνχξ(χ2+ξ2)−2δf2(2kx2μsDνχξ+ρ0ω(χ2−2ξ2))},(42)J_2 = De\mu_sD\nu\left(\chi^4+4\delta_f^2 k_x^2\xi^2-\xi^4\right)-2\delta_f^2\rho_0\omega\left(\chi^2-2\xi^2\right)+ De^2\left\{2\mu_sD\nu\chi\xi\left(\chi^2+\xi^2\right)-2\delta_f^2\left(2k_x^2\mu_sD\nu\chi\xi+\rho_0\omega\left(\chi^2-2\xi^2\right)\right)\right\}, \tag*{(42)}
J3=−2DeμsDνχξ(2δf2kx2+χ2+ξ2)−6δf2ρ0ωχξ−De2{μsDν(−χ4+ξ4)+2δf2(kx2μsDν(χ2+3ξ2)+3ρ0ωχξ)}.(43)J_3=-2De\mu_sD\nu\chi\xi\left(2\delta_f^2 k_x^2+\chi^2+\xi^2\right)-6\delta_f^2\rho_0\omega\chi\xi- De^2\left\{\mu_sD\nu\left(-\chi^4+\xi^4\right)+2\delta_f^2\left(k_x^2\mu_sD\nu\left(\chi^2+3\xi^2\right)+3\rho_0\omega\chi\xi\right)\right\}. \tag*{(43)}

In the present analysis, ϵ=δ/d≪1\epsilon=\delta/d\ll1 implies that ⟨v2,yδ⟩∼ϵ⟨v2,xδ⟩\langle v_{2,y}^{\delta}\rangle\sim\epsilon\langle v_{2,x}^{\delta}\rangle, giving transverse component of the second-order streaming velocity in the boundary layer negligible. Nevertheless, for completeness and to provide a comprehensive theoretical framework, an explicit expression for ⟨v2,yδ⟩\langle v_{2,y}^{\delta}\rangle is derived. Using Eqs. (33), (8), (15), (25) and (40), the component of second order streaming velocity perpendicular the standing wave becomes

⟨v2,yδ⟩=−38(v10)2c0kxδf3(1+De2)μs(Dν+1)χ3(χ2+ξ2)3e−2x/δf{H1exy/δf(ξcos⁡[ξy/δf]+χsin⁡[ξy/δf])+cos⁡[2kxx](H2+H3exy/δfcos⁡[ξy/δf]−H4exy/δfsin⁡[ξy/δf])}.(44)\left\langle v_{2,y}^{\delta}\right\rangle=-\frac{3}{8}\frac{\left(v_1^0\right)^2}{c_0}\frac{k_x\delta_f}{3\left(1+De^2\right)\mu_s\left(D\nu+1\right)\chi^3\left(\chi^2+\xi^2\right)^3}e^{-2x/\delta_f} \left\{H_1e^{x y/\delta_f}\left(\xi\cos\left[\xi y/\delta_f\right]+\chi\sin\left[\xi y/\delta_f\right]\right)+ \cos\left[2k_xx\right]\left(H_2+H_3e^{x y/\delta_f}\cos\left[\xi y/\delta_f\right]-H_4e^{x y/\delta_f}\sin\left[\xi y/\delta_f\right]\right)\right\}. \tag*{(44)}

Here H1H_1, H2H_2, H3H_3 and H4H_4 are

H1=−2(1+De2)μs(Dν+1)χ3(χ2+ξ2)2,(45)H_1=-2\left(1+De^2\right)\mu_s\left(D\nu+1\right)\chi^3\left(\chi^2+\xi^2\right)^2, \tag*{(45)}
H2=ξ(χ2+ξ2)2{2DeμsDνξ(δf2kx2+χ2−ξ2)+c0δf2kxξ$ρ0+De2(−4μsDνχ3+δf2kx(4kxμsDνχ+c0ξρ0))},(46)H_2=\xi\left(\chi^2+\xi^2\right)^2\left\{2De\mu_sD\nu\xi\left(\delta_f^2k_x^2+\chi^2-\xi^2\right)+c_0\delta_f^2k_x\xi\$\rho_0+ De^2\left(-4\mu_sD\nu\chi^3+\delta_f^2k_x\left(4k_x\mu_sD\nu\chi+c_0\xi\rho_0\right)\right)\right\}, \tag*{(46)}
H3=2χ3{−μs(Dν+1)ξ(χ2+ξ2)2+2DeμsDνχ(χ4+8δf2kx2ξ2+2χ2ξ2+ξ4)−4c0δf2kxχ(χ2−5ξ2)ρ0−De2((1−Dν)μsξ(χ2+ξ2)+4δf2kx(kxμsDνξ(χ2−3ξ2)+c0χ(χ2−5ξ2)ρ0))},(47)H_3=2\chi^3\left\{-\mu_s\left(D\nu+1\right)\xi\left(\chi^2+\xi^2\right)^2+2De\mu_sD\nu\chi\left(\chi^4+8\delta_f^2k_x^2\xi^2+2\chi^2\xi^2+\xi^4\right)- 4c_0\delta_f^2k_x\chi\left(\chi^2-5\xi^2\right)\rho_0-De^2\left((1-D\nu)\mu_s\xi\left(\chi^2+\xi^2\right)+4\delta_f^2k_x\left(k_x\mu_sD\nu\xi\left(\chi^2-3\xi^2\right)+ c_0\chi\left(\chi^2-5\xi^2\right)\rho_0\right)\right)\right\}, \tag*{(47)}
H4=2χ3{μs(Dν+1)χ(χ2+ξ2)2−2DeμsDνξ(4δf2kx2(χ2−ξ2)+(χ2+ξ2)2)+8c0δf2kxξ(−2χ2+ξ2)ρ0+De2((3Dν+1)μsχ(χ2+ξ2)−4δf2kx(kxμsDνχ(χ2+5ξ2)−2c0ξ(−2χ2+ξ2)ρ0))}.(48)H_4=2\chi^3\left\{\mu_s\left(D\nu+1\right)\chi\left(\chi^2+\xi^2\right)^2-2De\mu_sD\nu\xi\left(4\delta_f^2k_x^2\left(\chi^2-\xi^2\right)+\left(\chi^2+\xi^2\right)^2\right)+ 8c_0\delta_f^2k_x\xi\left(-2\chi^2+\xi^2\right)\rho_0+De^2\left((3D\nu+1)\mu_s\chi\left(\chi^2+\xi^2\right)-4\delta_f^2k_x\left(k_x\mu_sD\nu\chi\left(\chi^2+5\xi^2\right)- 2c_0\xi\left(-2\chi^2+\xi^2\right)\rho_0\right)\right)\right\}. \tag*{(48)}

Next the study focuses on ⟨v2,xδ⟩\langle v_{2,x}^{\delta}\rangle to determine the boundary conditions for outer streaming. At wall y=0y=0, from Eq. (40), the second order streaming velocity along the standing wave can be obtained as

⟨v2,xδ⟩=−38(v1d0)2c0sin⁡[2kxx]Cs,(49)\langle v_{2,x}^{\delta} \rangle= -\frac{3}{8}\frac{(v_{1}^{d0})^{2}}{c_{0}}\sin[2k_{x}x]C_{s}, \tag*{(49)}

where CsC_{s} is the coefficient of correction in acoustic streaming due to viscoelasticity of the fluid, which is named as streaming coefficient,

Cs=2ρ0c02I1+2DeDvμs∗I2+2De2I33(1+De2)χ2(χ2+ξ2)2ρ0c02μs∗(1+Dv).(50)C_{s}=\frac{2\rho_{0}c_{0}^{2}I_{1}+2DeDv\mu_{s}^{*}I_{2}+2De^{2}I_{3}}{3(1+De^{2})\chi^{2}(\chi^{2}+\xi^{2})^{2}\rho_{0}c_{0}^{2}\mu_{s}^{*}(1+Dv)}. \tag*{(50)}

Here I1I_{1}, I2I_{2} and I3I_{3} are functions of DvDv and DeDe, can be defined as

I1=−4χ4+9χ2ξ2+ξ4,(51)I_{1}=-4\chi^{4}+9\chi^{2}\xi^{2}+\xi^{4}, \tag*{(51)}
I2=2μfωξ2(5χ2+ξ2)+ρ0c02(χ2−ξ2)(χ2+ξ2)2,(52)I_{2}=2\mu_{f}\omega\xi^{2}(5\chi^{2}+\xi^{2})+\rho_{0}c_{0}^{2}(\chi^{2}-\xi^{2})(\chi^{2}+\xi^{2})^{2}, \tag*{(52)}
I3=4Dvμsωχξ(−χ2+ξ2)+ρ0c02(−4χ4+9χ2ξ2+ξ4).(53)I_{3}=4Dv\mu_{s}\omega\chi\xi(-\chi^{2}+\xi^{2})+\rho_{0}c_{0}^{2}(-4\chi^{4}+9\chi^{2}\xi^{2}+\xi^{4}). \tag*{(53)}

The boundary layer streaming velocity ⟨v2,xδ⟩\langle v_{2,x}^{\delta}\rangle provides a slip boundary condition for the bulk acoustic streaming field ⟨v2,xd⟩\langle v_{2,x}^{d}\rangle, where ⟨v2,xd⟩=⟨v2,xδ⟩s+⟨v2,xd⟩=0\langle v_{2,x}^{d}\rangle=\langle v_{2,x}^{\delta}\rangle_{s}+\langle v_{2,x}^{d}\rangle=0. Therefore long ranged field at y=0y=0 becomes

⟨v2,xd⟩=−⟨v2,xδ⟩=38(v1d0)2c0sin⁡[2kxx]Cs(54)\langle v_{2,x}^{d}\rangle=-\langle v_{2,x}^{\delta}\rangle=\frac{3}{8}\frac{(v_{1}^{d0})^{2}}{c_{0}}\sin[2k_{x}x]C_{s} \tag*{(54)}

Here CsC_{s} is obtained from Eqs. (50)–(53). For a Newtonian viscous fluid, De=0De=0, Dv=0Dv=0 where the streaming coefficient reduces to 1. Therefore Eq. (49) reduces to

⟨v2,xδ⟩=−38(v1d0)2c0sin⁡[2kxx],(55)\langle v_{2,x}^{\delta}\rangle=-\frac{3}{8}\frac{(v_{1}^{d0})^{2}}{c_{0}}\sin[2k_{x}x], \tag*{(55)}

which is the classical Rayleigh streaming for Newtonian fluids with streaming velocity amplitude vstr=3(v1d0)2/8c0v_{\mathrm{str}}=3(v_{1}^{d0})^{2}/8c_{0}.

Analytical form of outer boundary-layer streaming

The long range continuity and momentum equations can be represented as

∇⋅[ρ0⟨v2d⟩+⟨ρ1v1d⟩]=0(56)\nabla\cdot\left[\rho_{0}\langle\boldsymbol{v}_{2}^{d}\rangle+\langle\rho_{1}\boldsymbol{v}_{1}^{d}\rangle\right]=0 \tag*{(56)}

and

ρ0∇⋅⟨v1dv1d⟩=−∇⟨p2d⟩+μ∇2⟨v2d⟩+μ3∇(∇⋅⟨v2d⟩)−τ∇⋅⟨v1d⋅∇σ1⟩+τ∇⋅⟨(∇v1d)T⋅σ1⟩+τ∇⋅⟨σ1⋅∇v1d⟩.(57)\rho_{0}\nabla\cdot\langle\boldsymbol{v}_{1}^{d}\boldsymbol{v}_{1}^{d}\rangle=-\nabla\langle p_{2}^{d}\rangle+\mu\nabla^{2}\langle\boldsymbol{v}_{2}^{d}\rangle+\frac{\mu}{3}\nabla\left(\nabla\cdot\langle\boldsymbol{v}_{2}^{d}\rangle\right)-\tau\nabla\cdot\langle\boldsymbol{v}_{1}^{d}\cdot\nabla\boldsymbol{\sigma}_{1}\rangle+\tau\nabla\cdot\left\langle\left(\nabla\boldsymbol{v}_{1}^{d}\right)^{T}\cdot\boldsymbol{\sigma}_{1}\right\rangle+\tau\nabla\cdot\langle\boldsymbol{\sigma}_{1}\cdot\nabla\boldsymbol{v}_{1}^{d}\rangle. \tag*{(57)}

Equation (56) can be rewritten as

∇⋅⟨v2d⟩=−∇⋅⟨ρ1v1d⟩ρ0=−⟨ρ1∇⋅v1d+v1d⋅∇ρ1⟩ρ0(58)\nabla\cdot\langle\boldsymbol{v}_{2}^{d}\rangle=-\frac{\nabla\cdot\langle\rho_{1}\boldsymbol{v}_{1}^{d}\rangle}{\rho_{0}}=-\frac{\langle\rho_{1}\nabla\cdot\boldsymbol{v}_{1}^{d}+\boldsymbol{v}_{1}^{d}\cdot\nabla\rho_{1}\rangle}{\rho_{0}} \tag*{(58)}

Using p1=ρ1c02p_{1}=\rho_{1}c_{0}^{2} and Eq. (15), ∇⋅⟨v2d⟩\nabla\cdot\langle\boldsymbol{v}_{2}^{d}\rangle is scaled to (k/c0)(v1d0)2(k/c_{0})(v_{1}^{d0})^{2}. Here, k≪1k\ll1 and c0≫1c_{0}\gg1, therefore Eq. (58) reduces to [14, 1]

∇⋅⟨v2d⟩≈0(59)\nabla\cdot\langle\boldsymbol{v}_{2}^{d}\rangle\approx0 \tag*{(59)}

Using Eq. (59), the Eq. (57) can be rewritten as

μ∇2⟨v2d⟩=ρ0∇⋅⟨v1dv1d⟩+∇⟨p2d⟩+τ∇⋅⟨v1d⋅∇σ1⟩−τ∇⋅⟨(∇v1d)T⋅σ1⟩−τ∇⋅⟨σ1⋅∇v1d⟩.(60)\mu\nabla^{2}\langle v_{2}^{d}\rangle= \rho_{0}\nabla\cdot\langle v_{1}^{d}v_{1}^{d}\rangle+ \nabla\langle p_{2}^{d}\rangle+ \tau\nabla\cdot\langle v_{1}^{d} \cdot\nabla\boldsymbol{\sigma}_{1}\rangle- \tau\nabla\cdot\left\langle\left(\nabla v_{1}^{d}\right)^{T} \cdot\boldsymbol{\sigma}_{1}\right\rangle- \tau\nabla\cdot\langle\boldsymbol{\sigma}_{1} \cdot\nabla v_{1}^{d}\rangle. \tag*{(60)}

As mentioned earlier the first order velocity field is v1d=v1d0cos⁡(kxx) exv_{1}^{d}=v_{1}^{d0}\cos(k_{x}x)\,e_{x}. Analysis of curl of right hand side terms of Eq. (60) gives: ∇×[τ∇⋅⟨v1d⋅∇σ1⟩−τ∇⋅⟨(∇v1d)T⋅σ1⟩−τ∇⋅⟨σ1⋅∇v1d⟩]→0\nabla\times\left[\tau\nabla\cdot\langle v_{1}^{d}\cdot\nabla\boldsymbol{\sigma}_{1}\rangle-\tau\nabla\cdot\left\langle\left(\nabla v_{1}^{d}\right)^{T}\cdot\boldsymbol{\sigma}_{1}\right\rangle-\tau\nabla\cdot\langle\boldsymbol{\sigma}_{1}\cdot\nabla v_{1}^{d}\rangle\right]\to0, ∇×[ρ0∇⋅⟨v1dv1d⟩]→0\nabla\times\left[\rho_{0}\nabla\cdot\langle v_{1}^{d}v_{1}^{d}\rangle\right]\to0, ∇×∇⟨p2d⟩→0\nabla\times\nabla\langle p_{2}^{d}\rangle\to0. Therefore the entire right side terms can be represented as the gradient of a scalar function PP [14], where PP is the effective viscoelastic hydrostatic pressure, which consider the effect of momentum flux, second order pressure and viscoelastic stress. Therefore Eq. (60) can be written as

μ∇2⟨v2d⟩=∇P.(61)\mu\nabla^{2}\langle v_{2}^{d}\rangle= \nabla P. \tag*{(61)}

To derive the equations of motion for steady outer streaming, the study considers Eqs. (61) and (59) in conjunction with the relevant boundary conditions. On the channel walls, perpendicular to the standing wave, viscoelastic effects give rise to a tangential velocity due to the inner streaming. This leads to the emergence of the bulk second-order streaming slip velocity, where ⟨v2d⟩s=⟨v2,xd⟩\langle v_{2}^{d}\rangle_{s}=\langle v_{2,x}^{d}\rangle and ⟨v2o⟩s=⟨v2,yo⟩\langle v_{2}^{o}\rangle_{s}=\langle v_{2,y}^{o}\rangle, can be represented as

⟨v2d⟩s=−⟨v2o⟩s=38(v1d0)2c0sin⁡[2kxx]Csex.(62)\langle v_{2}^{d}\rangle_{s}=-\langle v_{2}^{o}\rangle_{s}=\frac{3}{8}\frac{\left(v_{1}^{d0}\right)^{2}}{c_{0}}\sin[2k_{x}x]C_{s}e_{x}. \tag*{(62)}

Here, ⟨v2d⟩s\langle v_{2}^{d}\rangle_{s} indicate the modified slip velocity for a viscoelastic fluid for outer streaming. However, on the walls where the the acoustic velocity does not have a tangential component, the no slip boundary condition becomes

⟨v2d⟩s=0.(63)\langle v_{2}^{d}\rangle_{s}=0. \tag*{(63)}

The bulk streaming velocity is represented as [14]

⟨v2d⟩=∇×(ψez),(64)\langle v_{2}^{d}\rangle=\nabla\times(\psi e_{z}), \tag*{(64)}

where ψ\psi is the stream function, ⟨v2d⟩=⟨v2,xd⟩ex+⟨v2,yd⟩ey\langle v_{2}^{d}\rangle=\langle v_{2,x}^{d}\rangle e_{x}+\langle v_{2,y}^{d}\rangle e_{y}. Therefore ⟨v2,xd⟩=∂ψ/∂y\langle v_{2,x}^{d}\rangle=\partial\psi/\partial y and ⟨v2,yd⟩=−∂ψ/∂x\langle v_{2,y}^{d}\rangle=-\partial\psi/\partial x. Substituting Eq. (64) in Eq. (61) and calculating the curl of the resulting equation gives

∇4ψ=0.(65)\nabla^{4}\psi=0. \tag*{(65)}

As previously noted, ∇×∇P=0\nabla\times\nabla P=0. To obtain the steady streaming patterns, the Eq. (65) is solved subject to the appropriate boundary conditions by following Lee & Wang [14]. From Eqs. (62) and (63), ∂ψ/∂y=⟨v2d⟩s\partial\psi/\partial y=\langle v_{2}^{d}\rangle_{s} and ψ=0\psi=0 on the channel walls. For the present case of outer streaming, the coordinate origin is at the center of the channel cross section, with XX and YY denoting the directions, as illustrated in Figure 1. Accordingly, at X=±D/2X=\pm D/2, the boundary condition becomes ∂ψ/∂Y=⟨v2d⟩s\partial\psi/\partial Y=\langle v_{2}^{d}\rangle_{s}. Solving Eq. (65) with these conditions yields

ψ=3Cs8(v1d0)2c0sin⁡[2kxX] Γ(kx,D){psinh⁡[2kxY]−Yqcosh⁡[2kxY]}.(66)\psi=\frac{3C_{s}}{8}\frac{\left(v_{1}^{d0}\right)^{2}}{c_{0}}\sin[2k_{x}X]\,\Gamma(k_{x},D)\left\{p\sinh[2k_{x}Y]-Yq\cosh[2k_{x}Y]\right\}. \tag*{(66)}

where Υ(kx,D)\Upsilon(k_x,D), pp and qq are

Υ(kx,D)=1(kxD−sinh⁡[kxD]cosh⁡[kxD]),(67)\Upsilon(k_x,D)=\frac{1}{\left(k_xD-\sinh[k_xD]\cosh[k_xD]\right)}, \tag*{(67)}
p=(D/2)cosh⁡[kxD],andq=sinh⁡[kxD].(68)p=(D/2)\cosh[k_xD],\quad\text{and}\quad q=\sinh[k_xD]. \tag*{(68)}

Therefore, the components of the streaming velocity can be determined directly from the stream function as: ⟨v2,Xd⟩=∂ψ/∂Y\langle v^d_{2,X}\rangle=\partial\psi/\partial Y and ⟨v2,Yd⟩=−∂ψ/∂X\langle v^d_{2,Y}\rangle=-\partial\psi/\partial X. Finally, the outer streaming velocity becomes

⟨v2,Xd⟩=3Cs8(v1d0)2c0sin⁡[2kxX]Υ(kx,D){(2kxp−q)cosh⁡[2kxY]−2kxqYsinh⁡[2kxY]}(69)\langle v^d_{2,X}\rangle=\frac{3C_s}{8}\frac{(v^{d0}_1)^2}{c_0}\sin[2k_xX]\Upsilon(k_x,D)\left\{(2k_xp-q)\cosh[2k_xY]-2k_xqY\sinh[2k_xY]\right\} \tag*{(69)}
⟨v2,Yd⟩=−3Cs8(v1d0)2c0cos⁡[2kxX]Υ(kx,D){2kxpsinh⁡[2kxY]−2kxqYcosh⁡[2kxY]}(70)\langle v^d_{2,Y}\rangle=-\frac{3C_s}{8}\frac{(v^{d0}_1)^2}{c_0}\cos[2k_xX]\Upsilon(k_x,D)\left\{2k_xp\sinh[2k_xY]-2k_xqY\cosh[2k_xY]\right\} \tag*{(70)}

The expressions given in Eqs. (69) and (70) are derived for a parallel-plate channel and therefore neglect the effects of lateral sidewalls, where the velocity field must satisfy the no-slip condition at X=±W/2X=\pm W/2. This omission can lead to the presence of a non-zero vertical velocity component ⟨v2,Yd⟩\langle v^d_{2,Y}\rangle near the sidewalls, which must be canceled to maintain physical consistency. To resolve this, an iterative correction procedure outlined in Ref. Muller et al. [18] is followed, wherein the problem is corrected by rotating the coordinate system by 90∘90^\circ. Introducing non-dimensional variables X~=X/(W/2)\widetilde{X}=X/(W/2), Y~=Y/(D/2)\widetilde{Y}=Y/(D/2), and the aspect ratio β=D/W\beta=D/W, the velocity boundary conditions for the rectangular channel become: (i) ⟨v2,Xd⟩=⟨v2d⟩s\langle v^d_{2,X}\rangle=\langle v^d_{2}\rangle_s at Y~=±1\widetilde{Y}=\pm1, (ii) ⟨v2,Yd⟩=0\langle v^d_{2,Y}\rangle=0 at Y~=±1\widetilde{Y}=\pm1, (iii) ⟨v2,Xd⟩=0\langle v^d_{2,X}\rangle=0 at X~=±1\widetilde{X}=\pm1, and (iv) ⟨v2,Yd⟩=0\langle v^d_{2,Y}\rangle=0 at X~=±1\widetilde{X}=\pm1. Perpendicular-to-the-wall velocity conditions (ii) and (iii) enforce the vanishing of the velocity component normal to the walls, while parallel-to-the-wall velocity conditions (i) and (iv) specify the tangential components. To simultaneously satisfy all these constraints, an iterative Fourier expansion of the velocity field is employed, expressed as an infinite series, the full formulation can be found in the Muller et al. [18]. Finally, the outer streaming components in rectangular channel can be represented as

⟨v2,Xd(X~,Y~)⟩=Csvstr∑n=1∞{C1nsin⁡[nπX~]A∥(nβ,Y~)+C2nA⊥(nβ−1,X~)cos⁡[nπY~]},(71)\langle v^d_{2,X}(\widetilde{X},\widetilde{Y})\rangle=C_s v_{\mathrm{str}}\sum_{n=1}^{\infty}\left\{C_{1n}\sin[n\pi\widetilde{X}]A^{\parallel}(n\beta,\widetilde{Y})+C_{2n}A^{\perp}(n\beta^{-1},\widetilde{X})\cos[n\pi\widetilde{Y}]\right\}, \tag*{(71)}
⟨v2,Yd(X~,Y~)⟩=Csvstr∑n=1∞{C1ncos⁡[nπX~]A∥(nβ,Y~)+C2nA⊥(nβ−1,X~)sin⁡[nπY~]}.(72)\langle v^d_{2,Y}(\widetilde{X},\widetilde{Y})\rangle=C_s v_{\mathrm{str}}\sum_{n=1}^{\infty}\left\{C_{1n}\cos[n\pi\widetilde{X}]A^{\parallel}(n\beta,\widetilde{Y})+C_{2n}A^{\perp}(n\beta^{-1},\widetilde{X})\sin[n\pi\widetilde{Y}]\right\}. \tag*{(72)}

Here, vstr=(3/8)((v1d0)2/c0)v_{\mathrm{str}}=(3/8)((v^{d0}_1)^2/c_0) and the dimensionless outer streaming components (⟨v~2d⟩=⟨v2d⟩/vstr)(\langle\widetilde{\boldsymbol{v}}^d_2\rangle=\langle\boldsymbol{v}^d_2\rangle/v_{\mathrm{str}}) can be represented as

⟨v~2,Xd(X~,Y~)⟩=Cs∑n=1∞{C1nsin⁡[nπX~]A∥(nβ,Y~)+C2nA⊥(nβ−1,X~)cos⁡[nπY~]}=Cs⟨v~2,Xd(X~,Y~)⟩N,(73)\begin{aligned} \langle\widetilde{v}^d_{2,X}(\widetilde{X},\widetilde{Y})\rangle &=C_s\sum_{n=1}^{\infty}\left\{C_{1n}\sin[n\pi\widetilde{X}]A^{\parallel}(n\beta,\widetilde{Y})+\right.\\ &\qquad\left.C_{2n}A^{\perp}(n\beta^{-1},\widetilde{X})\cos[n\pi\widetilde{Y}]\right\} =C_s\langle\widetilde{v}^d_{2,X}(\widetilde{X},\widetilde{Y})\rangle_N, \tag*{(73)} \end{aligned}
⟨v~2,Yd(X~,Y~)⟩=Cs∑n=1∞{C1ncos⁡[nπX~]A∥(nβ,Y~)+C2nA⊥(nβ−1,X~)sin⁡[nπY~]}=Cs⟨v~2,Yd(X~,Y~)⟩N.(74)\left\langle\widetilde{v}^{d}_{2,Y}(\widetilde{X},\widetilde{Y}) \right\rangle= C_s \sum_{n=1}^{\infty} \left\{ C_{1n}\cos[n\pi\widetilde{X}]A^{\parallel}(n\beta,\widetilde{Y}) + C_{2n}A^{\perp}(n\beta^{-1},\widetilde{X})\sin[n\pi\widetilde{Y}] \right\} = C_s\left\langle\widetilde{v}^{d}_{2,Y}(\widetilde{X},\widetilde{Y}) \right\rangle_N. \tag*{(74)}

In the above equations, ⟨v~2,Yd⟩N\left\langle\widetilde{v}^{d}_{2,Y} \right\rangle_N refers to the time-averaged second order classical Rayleigh streaming velocity for a Newtonian fluid in a rectangular channel ([18]). The coefficients A∥(nβ,Y~)A^{\parallel}(n\beta,\widetilde{Y}), and A+(nβ,Y~)A^{+}(n\beta,\widetilde{Y}) are obtained as Muller et al. [18],

A∥(nβ,Y~)=Λ(nβ){nπβcosh⁡[nπβ]cosh⁡[nπβY~]−sinh⁡[nπβ]cosh⁡[nπβY~]−nπβY~sinh⁡[nπβ]sinh⁡[nπβY~]}.(75)A^{\parallel}(n\beta,\widetilde{Y}) = \Lambda(n\beta)\left\{n\pi\beta\cosh[n\pi\beta]\cosh[n\pi\beta\widetilde{Y}] - \sinh[n\pi\beta]\cosh[n\pi\beta\widetilde{Y}] - n\pi\beta\widetilde{Y}\sinh[n\pi\beta]\sinh[n\pi\beta\widetilde{Y}]\right\}. \tag*{(75)}
A+(nβ,Y~)=Λ(nβ){nπβcosh⁡[nπβ]sinh⁡[nπβY~]−sinh⁡[nπβ]cosh⁡[nπβY~]−nπβY~sinh⁡[nπβ]cosh⁡[nπβY~]}.(76)A^{+}(n\beta,\widetilde{Y}) = \Lambda(n\beta)\left\{n\pi\beta\cosh[n\pi\beta]\sinh[n\pi\beta\widetilde{Y}] - \sinh[n\pi\beta]\cosh[n\pi\beta\widetilde{Y}] - n\pi\beta\widetilde{Y}\sinh[n\pi\beta]\cosh[n\pi\beta\widetilde{Y}]\right\}. \tag*{(76)}

where Λ(nβ)\Lambda(n\beta) becomes

Λ(nβ)=1nπβ−sinh⁡[nπβ]cosh⁡[nπβ].(77)\Lambda(n\beta) = \frac{1}{n\pi\beta-\sinh[n\pi\beta]\cosh[n\pi\beta]}. \tag*{(77)}

Moreover, A∥(nβ−1,X~)A^{\parallel}(n\beta^{-1},\widetilde{X}), A⊥(nβ−1,X~)A^{\perp}(n\beta^{-1},\widetilde{X}), and Λ(nβ−1)\Lambda(n\beta^{-1}) are obtained from Eqs. (75), (76), and (77) by replacing nβn\beta with nβ−1n\beta^{-1} and Y~\widetilde{Y} with X~\widetilde{X}. Moreover, C1nC_{1n} and C2nC_{2n} are unknown coefficients and determined using parallel-to-the-wall conditions, followed by Muller et al. [18],

C1=[I−A⊥(β−1)A⊥(β)]−1⋅e1,(78)C_1 = [I-A^{\perp}(\beta^{-1})A^{\perp}(\beta)]^{-1}\cdot e_1, \tag*{(78)}
C2=−A⊥(β)⋅C1.(79)C_2 = -A^{\perp}(\beta)\cdot C_1. \tag*{(79)}
Aj,n⊥(β−1)=(−1)n∫−11dX~A⊥(nβ−1,X~)sin⁡(jπX~).(80)A^{\perp}_{j,n}(\beta^{-1}) = (-1)^n\int_{-1}^{1}d\widetilde{X}A^{\perp}(n\beta^{-1},\widetilde{X})\sin(j\pi\widetilde{X}). \tag*{(80)}

Using Eqs. (40), (2.44), (71), and (72), the total second-order streaming velocity is given by ⟨v2⟩=⟨v2δ⟩+⟨v2d⟩\left\langle v_2 \right\rangle= \left\langle v^{\delta}_2 \right\rangle+\left\langle v^{d}_2 \right\rangle, where ⟨v2δ⟩\left\langle v^{\delta}_2 \right\rangle represents the contribution from the inner boundary layers and ⟨v2d⟩\left\langle v^{d}_2 \right\rangle corresponds to the bulk (outer) streaming. Since the boundary layer thickness is much smaller than the channel depth dd (i.e., δ≪d\delta\ll d), the inner streaming is confined to a narrow region near the top and bottom walls. As a result, the dominant observable flow in the bulk of the fluid is governed by the outer streaming. Therefore, in the bulk region, the total streaming velocity can be approximated as ⟨v2⟩≈⟨v2d⟩\left\langle v_2 \right\rangle\approx\left\langle v^{d}_2 \right\rangle. The vstrv_{\mathrm{str}} is used to non-dimensionalize the streaming velocity within the channel.

Contributions of Reynolds and viscoelastic stresses to acoustic Streaming

To quantify the individual contributions of the stresses, the time-averaged second-order streaming slip velocity is expressed as ⟨v~2δ⟩s=SRES,v+SRES,ve+SVES\left\langle\widetilde{v}^{\delta}_2 \right\rangle_s = S_{\mathrm{RES},v}+S_{\mathrm{RES},ve}+S_{\mathrm{VES}}. Here ⟨v~2δ⟩s=⟨v2δ⟩s/vstr\left\langle\widetilde{v}^{\delta}_2 \right\rangle_s = \left\langle v^{\delta}_2 \right\rangle_s/v_{\mathrm{str}}, from Eqs. (62) and (50), the individual contributions of viscous RES (SRES,vS_{\mathrm{RES},v}), viscoelastic RES (SRES,veS_{\mathrm{RES},ve}), and VES (SVESS_{\mathrm{VES}}) can be expressed as

SRES,v=−13e−2xvy/δf(1+6exvy/δfsin⁡[ξvy/δf]+2exvy/δfcos⁡[ξvy/δf])sin⁡[2kxx].(81)S_{\mathrm{RES},v}=-\frac{1}{3}e^{-2x_v y/\delta_f}\left(1+6e^{x_v y/\delta_f}\sin[\xi_v y/\delta_f]+2e^{x_v y/\delta_f}\cos[\xi_v y/\delta_f]\right)\sin[2k_xx]. \tag*{(81)}
SRES,ve=16{16(χ2−2ξ2)e−χy/δfcos⁡[ξy/δf](χ2+ξ2)2μs∗(1+Dv)+4e−χvy/δfcos⁡[ξvy/δf]−4ξe−2χy/δfχ(χ2+ξ2)2μs∗(1+Dv)(χ2ξ+ξ3+12χ3eχy/δfsin⁡[ξy/δf])+2e−2χvy/δf(1+6eχvy/δfsin⁡[ξvy/δf])}sin⁡[2kxx],(82)S_{\mathrm{RES},\mathrm{ve}}=\frac{1}{6}\left\{\frac{16(\chi^2-2\xi^2)e^{-\chi y/\delta_f}\cos[\xi y/\delta_f]}{(\chi^2+\xi^2)^2\mu_s^*(1+D_v)}+4e^{-\chi_v y/\delta_f}\cos[\xi_v y/\delta_f]-\frac{4\xi e^{-2\chi y/\delta_f}}{\chi(\chi^2+\xi^2)^2\mu_s^*(1+D_v)}\left(\chi^2\xi+\xi^3+12\chi^3e^{\chi y/\delta_f}\sin[\xi y/\delta_f]\right)+2e^{-2\chi_v y/\delta_f}\left(1+6e^{\chi_v y/\delta_f}\sin[\xi_v y/\delta_f]\right)\right\}\sin[2k_xx], \tag*{(82)}
SVES=2DeDv3χ2(χ2+ξ2)2(1+De2)(1+Dv)e−2χy/δf{H1−H2eχy/δfcos⁡[ξy/δf]+H3eχy/δfsin⁡[ξy/δf]}sin⁡[2kxx],(83)S_{\mathrm{VES}}=\frac{2D_eD_v}{3\chi^2(\chi^2+\xi^2)^2(1+D_e^2)(1+D_v)}e^{-2\chi y/\delta_f}\left\{H_1-H_2e^{\chi y/\delta_f}\cos[\xi y/\delta_f]+H_3e^{\chi y/\delta_f}\sin[\xi y/\delta_f]\right\}\sin[2k_xx], \tag*{(83)}
H1=ξ(χ2+ξ2)(−χ2ξ+ξ3+2χ3De−2χDeδf2kx2−ξδf2kx2),(84)H_1=\xi(\chi^2+\xi^2)\left(-\chi^2\xi+\xi^3+2\chi^3D_e-2\chi D_e\delta_f^2k_x^2-\xi\delta_f^2k_x^2\right), \tag*{(84)}
H2=χ2(χ4+2χ3ξDe+2χξDe(ξ2−2δf2kx2)−ξ4+4ξ2δf2kx2),(85)H_2=\chi^2\left(\chi^4+2\chi^3\xi D_e+2\chi\xi D_e\left(\xi^2-2\delta_f^2k_x^2\right)-\xi^4+4\xi^2\delta_f^2k_x^2\right), \tag*{(85)}
H3=χ2(χ4De−2χ3ξ−2χ2Deδf2kx2)−2χ(ξ3+2ξδf2kx2)−ξ2De(ξ2+6δf2kx2).(86)H_3=\chi^2\left(\chi^4D_e-2\chi^3\xi-2\chi^2D_e\delta_f^2k_x^2\right)-2\chi\left(\xi^3+2\xi\delta_f^2k_x^2\right)-\xi^2D_e\left(\xi^2+6\delta_f^2k_x^2\right). \tag*{(86)}

Here, χv\chi_v and ξv\xi_v are functions of viscosity, given by χv=ξv=[μs∗(Dv+1)]−0.5\chi_v=\xi_v=[\mu_s^*(D_v+1)]^{-0.5}. In contrast, χ\chi and ξ\xi depend on both viscosity and elasticity, as defined in Eqs. (26), (27), and (28).

Experiments

The experiments are conducted using the same glass–silicon–glass microfluidic chip previously described in Sujith et al. [28], also shown in Figure 2. The chip is fabricated via standard photolithography followed by deep reactive ion etching (DRIE). Fabrication begins with a 3-inch, 300 μ\mum thick, <100> silicon wafer, onto which the microchannel pattern is transferred using a positive photoresist (MICROPOSIT S1813) and ultraviolet (UV) exposure. The patterned wafer is then through-etched to form a channel with dimensions of 20 mm in length, 400 μ\mum in width, and 300 μ\mum in depth. To enclose the etched channel, borosilicate glass plates, each 500 μ\mum thick, are bonded to both the top and bottom surfaces of the wafer through anodic bonding at 450°C under an applied voltage of 1000 V. Inlet and outlet ports are created by micro-drilling holes through the top glass layer to facilitate fluidic access.

Image not extracted

Figure 2. Schematic diagram showing the experimental set up.

The microchannel is filled with either Newtonian or viscoelastic working fluids containing suspended microparticles by a high-precision syringe pump (neMESYS, Cetoni GmbH, Germany), as shown in Figure 2. For acoustic actuation, a piezoelectric transducer (2.0 MHz, Sparkler Piezoceramics) is affixed to the bottom glass layer using epoxy adhesive. It is driven by a sinusoidal signal generated by a function generator (SMC100A, Rohde & Schwarz, Germany), which is subsequently amplified using a power amplifier (75A250A, Amplifier Research, USA) in the range of 10–1000 mW. The acoustic streaming is visualized using an inverted microscope (IX73, Olympus) with a high-speed CCD camera (Phantom), recording tracer particle motion at 100 frames per second across different focal planes. To determine the resonance frequency of the system, a suspension of 15 μ\mum polystyrene spheres is introduced into the channel. The transducer is then actuated over a frequency sweep from 1.85 to 2.1 MHz. The resonance condition is identified based on the formation of particle accumulation patterns and the time of migration, with the optimal operating frequency determined to be 1.93 MHz.

Types of fluids and characterization

In acoustic streaming experiments, the study uses dilute suspensions of 1 μ\mum fluorescent polystyrene particles (microParticles GmbH, Berlin) dispersed in both Newtonian and viscoelastic (VE) fluids. Deionized water (DI) serves as the Newtonian reference fluid. The VE medium consists of aqueous polyethylene oxide (PEO) solutions with molecular weights of 0.4, 1, and 2 MDa (Sigma-Aldrich, Bangalore, India), prepared at the concentrations listed in Table 1. To ensure complete homogenization, PEO is dissolved in DI water at 25°C and stirred continuously for at least 24 h. The fluid viscosities are measured with a rotational rheometer (Anton Paar MCR 72), and their dependence on shear rate is shown in Figure 3. For all polymer solutions, the viscosity remains nearly constant up to shear rates of about 400 s−1^{-1}, indicating a plateau regime. Only at very high shear rates do the high–molecular weight, high–concentration PEO solutions exhibit a slight decrease in viscosity. Since the shear rates relevant to the acoustic streaming experiments (less than 1s−1^{-1}) are much lower than this range, the solutions effectively exhibit constant viscosity with negligible shear-thinning. This rheological behavior justifies the choice of the Oldroyd-B model for describing the viscoelastic response in the theoretical framework.

PEO (MW)CC [∼ wt.%]μ\mu [mPa s]τ\tau [∼ μ\mus]DvD_vDeD_e
1 MDa0.051.200.43 ± 0.060.355.20 ± 0.80
1 MDa0.101.690.14 ± 0.090.901.75 ± 1.11
1 MDa0.503.190.80 ± 0.132.599.80 ± 1.53
2 MDa0.183.660.12 ± 0.033.121.40 ± 0.40
2 MDa0.357.121.65 ± 0.587.0120.04 ± 7.14
2 MDa0.5215.319.10 ± 2.4716.21110.45 ± 30.11
0.40 MDa0.9515.310.52 ± 0.1616.216.25 ± 2.01

Table 1. Concentration and viscoelastic properties of polyethylene oxide (PEO) solutions. The total viscosity is given by μ=μs+μp\mu= \mu_s + \mu_p, where the solvent viscosity is μs=0.89\mu_s = 0.89 mPa s (DI water). Data compiled from Refs. [16] (Wu et al. 2024; Wu et al. 2023).

Image not extracted

Figure 3. Variation of viscosity of aqueous PEO solutions at different concentrations with shear rate, showing a plateau at low shear rates and negligible shear-thinning in the range relevant to acoustic streaming experiments.

In this study, the fluid is subjected to high-frequency longitudinal pressure waves, typically in the MHz range. At these frequencies, the characteristic response of the fluid is governed by timescales distinct from those associated with low-frequency oscillations. To account for this, an approach based on ultrasound spectroscopy (Wu et al. 2024, 2023; Milliken & Powell [16]) is employed, which characterizes acoustic absorption and provides a relaxation time directly relevant to the actuation conditions of acoustofluidic systems. Specifically, the study consider the frequency-dependent acoustic absorption coefficient αs(f)\alpha_s(f) for PEO solutions, as reported in Refs. Wu et al. (2024, 2023); Milliken & Powell [16], and analyze the relaxation dynamics using the classical Debye relaxation model:

αs(f)=A11+(ffr)2+B.(87)\alpha_s(f) = \frac{A_1}{1+\left(\frac{f}{f_r}\right)^2} + B. \tag*{(87)}

In this expression, ff denotes the frequency, frf_r is the relaxation frequency, A1A_1 represents the relaxation amplitude, and BB accounts for background attenuation from non-relaxation mechanisms. A characteristic decrease in αs\alpha_s with increasing frequency indicates the presence of a relaxation process within the observed frequency range. By fitting Eq. (87) to the experimental absorption coefficient data for the PEO aqueous solutions (Wu et al. 2024, 2023), an estimate for the relaxation frequency frf_r is extracted. The corresponding relaxation time is then obtained as τ=1/fr\tau= 1/f_r, which agrees well with the values reported in [16]. This analysis enables a consistent characterization of fluid elasticity across all tested concentrations.

Characterization of acoustic streaming profiles via defocusing particle tracking

The motion of tracer particles induced by acoustic streaming is observed using an inverted microscope (IX73, Olympus) equipped with a high-speed CCD camera (Phantom), capturing video at 100 frames per second across multiple focal planes. To obtain depth information for the particle positions, a defocusing particle tracking method [4, 3] is employed.

The first step in defocusing particle tracking is to calibrate the system by recording images of tracer particles at known vertical positions or depth, thereby establishing the relationship between particle defocusing and depth. Calibration is performed using the same experimental setup as the measurements. Following Barnkob et al. [4, 3], particles that are either settled at the bottom of the microchannel and attached to the walls are used as reference points. By capturing their defocused images across focal plane, a mapping between the degree of defocusing and the particle’s position across channel depth is generated, which enables accurate three-dimensional reconstruction of particle trajectories during acoustic streaming experiments. During calibration, the microscope objective is moved while the tracer particles in the fluid remain stationary. In contrast, during actual experiments, the objective remains fixed while the particles move. To account for this difference, a correction factor is applied to the calibrated depth data. Additionally, since the objective is immersed in air while the particles are suspended in an aqueous dilute polymer solution, a calibration step of 1 μm1\,\mu\mathrm{m} corresponds to 1.33 μm1.33\,\mu\mathrm{m} during measurements due to the refractive index mismatch ([4, 3]).

Once the calibration is complete using the reference images, tracer particles in the streaming experiments videos are tracked using Tracker 6.1.0, a free video analysis and modeling software, and MATLAB scripts ([4, 3]). The particle trajectories are then reconstructed in MATLAB and Wolfram Mathematica to obtain the streaming profiles ([4, 3, 13, 23]).

Results and discussion

Under a standing acoustic wave imposed along the YY-direction, acoustic streaming is generated across the cross-section of the microchannel. We perform the analysis on the XYXY cross-section (Figure 1a) using the normalized coordinates X~=X/(W/2)\widetilde{X}=X/(W/2) and Y~=Y/(D/2)\widetilde{Y}=Y/(D/2), where tildes denote dimensionless variables. We consider dilute polymer solutions exhibiting viscoelastic (VE) behavior with negligible shear-thinning, and model the fluid rheology using the Oldroyd-B constitutive model ([19]). This model is characterized by a total viscosity μ=μs+μp\mu=\mu_s+\mu_p and a relaxation time τ\tau, where μs\mu_s and μp\mu_p denote the solvent and polymer contributions, respectively.

Acoustic streaming is analyzed within the framework of perturbation theory ([5, 7, 28]), accounting for both inner and outer streaming regions associated with distinct characteristic length scales ([1, 14]). A detailed formulation of the theoretical model is presented in § 2. The analysis incorporates several relevant time scales, including the acoustic time scale tac=1/ωt_{ac}=1/\omega, the polymer relaxation time τ\tau, the polymer viscous diffusion time td,p=(D/2)2/(2νp)t_{d,p}=(D/2)^2/(2\nu_p), and the solvent viscous diffusion time td,s=(D/2)2/(2νs)t_{d,s}=(D/2)^2/(2\nu_s), where ω=2πf\omega=2\pi f, and νp\nu_p and νs\nu_s are the kinematic viscosities of the polymer and solvent, respectively. The interplay among these time scales is quantified using the Deborah number De=τ/tacDe=\tau/t_{ac} and the viscous diffusion number Dv=td,s/td,p=νp/νsDv=t_{d,s}/t_{d,p}=\nu_p/\nu_s.

Effect of viscoelasticity on acoustic streaming

From the theoretical model (Eqs. (73) and (74)), the dimensionless streaming velocity ⟨v~2⟩\langle\widetilde{v}_2\rangle response of the VE fluid at Dv=20Dv=20 for varying DeDe is presented in Figure 4. Here, ⟨v~2⟩=⟨v2⟩/vstr\langle\widetilde{v}_2\rangle=\langle v_2\rangle/v_{\mathrm{str}}, where vstr=(3/8)(v1d0)2/c0v_{\mathrm{str}}=(3/8)(v_1^{d0})^2/c_0 is the Rayleigh streaming velocity, ⟨⋅⟩\langle\cdot\rangle denotes the time averaging, v1d0=Aωv_1^{d0}=A\omega is the first-order velocity amplitude, and c0c_0 is the speed of sound. The variation of dimensionless maximum streaming velocity, ⟨v~2⟩max⁡=⟨v2⟩max⁡,VE/⟨v2⟩max⁡,N\langle\widetilde{v}_2\rangle_{\max}=\langle v_2\rangle_{\max,\mathrm{VE}}/\langle v_2\rangle_{\max,\mathrm{N}} with DeDe, normalized by the Newtonian case (N, De=0De=0), is shown in Figure 4. In all cases, four counter-rotating outer streaming rolls are observed. The main findings are: (i) At very low DeDe (De≤1De \le1): viscous effects dominate, and increasing DeDe from 0 (purely viscous case) leads to streaming enhancement (SE). (ii) At low DeDe (1<De≤21 < De \le2): an increase in DeDe gives rise to streaming suppression (SS) as elastic effects become significant and begin to compete with viscous effects. (iii) At moderate DeDe (2<De≤42 < De \le4): there is streaming reversal (SR), and the reversed streaming magnitude increases (SR+\mathrm{SR}^{+}) as elasticity becomes more prominent. (iv) At high DeDe (4<De≤104 < De \le10): the reversed streaming weakens (SR−\mathrm{SR}^{-}) as elastic effects decline, leading to streaming suppression. (v) At very high DeDe (De>10De > 10): the original streaming direction re-emerges with a very weak streaming. These findings suggest that tuning the balance between viscous and elastic effects provides a powerful tool for modulating streaming motion: enabling its enhancement (SE), suppression (SS), or even reversal (SR), offering a straightforward yet effective strategy for acoustic streaming control. Here, a fundamental question arises: What underlying mechanisms govern the streaming transition? To understand the mechanisms, a distinguish of the two streaming regions: inner streaming in the boundary layer δve\delta_{ve}, and outer streaming in the bulk is needed. Since δve≪D\delta_{ve} \ll D or λ0\lambda_0, the Stokes parameter Sp=δve/D≪1S_p = \delta_{ve}/D \ll1. This scale separation allows decomposition of the field into a boundary region (“δ\delta”) and a bulk region (“dd”) (see Figure 1b).

Image not extracted

Figure 4. Analytical variation of streaming velocity profiles in the channel cross-section (XYXY plane) for Deborah numbers De=0De = 0 to 10310^3 at fixed Dv=20Dv = 20. Arrow length and direction represent the relative magnitude and direction of streaming compared to De=0De = 0 case. (c) Variation of the dimensionless maximum streaming velocity within a quarter of the microchannel cross-section as a function of DeDe at Dv=20Dv = 20, normalized by the Newtonian case (De=0De = 0). Labels SE, SS, and SR denote streaming enhancement, suppression, and reversal relative to the purely viscous case (De=0De = 0), while SR+\mathrm{SR}^{+} and SR−\mathrm{SR}^{-} indicate enhancement and suppression in the reversed direction.

The inner and outer acoustic streaming fields (Figure 1) are derived analytically using a second-order perturbation expansion of the continuity and momentum equations [28]. The first-order acoustic fields exhibit harmonic time dependence of the form eiωte^{i\omega t}, and the velocity field is decomposed using the Helmholtz representation [1] as v1=v1d+v1δ\mathbf{v}_1 = \mathbf{v}_1^d + \mathbf{v}_1^\delta, where the irrotational component is given by v1d(x,t)=v1dcos⁡(kxx)eiωt\mathbf{v}_1^d(x,t) = v_1^d \cos(k_x x)e^{i\omega t}, with kx=2π/λ0k_x = 2\pi/\lambda_0 denoting the acoustic wavenumber. The time-averaged second-order velocity field is similarly decomposed as ⟨v2⟩=⟨v2d⟩+⟨v2δ⟩\langle\mathbf{v}_2 \rangle= \langle\mathbf{v}_2^d \rangle+ \langle\mathbf{v}_2^\delta\rangle. Solution of the boundary-layer (δ\delta) equations yields the inner streaming field and an effective slip-velocity boundary condition at the walls [14], which drives the bulk (outer) streaming flow [24].

The outer (dd) streaming solution for parallel plates is extended to rectangular microchannels with aspect ratio β=D/W\beta= D/W using a Fourier series expansion ([18]). The complete mathematical derivation is provided in § 2, from which the time-averaged second-order streaming velocity in the bulk is obtained,

⟨v~2(X~,Y~)⟩=Cs⟨v~2(X~,Y~)⟩N(88)\left\langle\widetilde{\mathbf{v}}_2(\widetilde{X},\widetilde{Y}) \right\rangle= C_s \left\langle\widetilde{\mathbf{v}}_2(\widetilde{X},\widetilde{Y}) \right\rangle_N \tag*{(88)}

In Eq. (88), ⟨v~2⟩N\langle\widetilde{\mathbf{v}}_2\rangle_N represents the Rayleigh streaming velocity for a Newtonian fluid in a rectangular microchannel ([18]), while CsC_s is the streaming coefficient introduced to account for viscoelastic effects. The theoretical predictions are validated against experiments performed using 1 μm1\,\mu\mathrm{m} fluorescent polystyrene tracer particles suspended in polyethylene oxide (PEO) solutions with molecular weights of 0.4, 1, and 2 MDa (see Figure 5a–c). These measurements provide experimental evidence of streaming enhancement (SE), suppression (SS), and reversal (SR) in viscoelastic fluids confined within microchannels. The spatial variation of the streaming velocity over one quarter of the channel cross-section is quantified experimentally using the defocusing particle tracking technique ([4, 3]) and compared with theoretical predictions obtained from Eq. (88), as shown in Figure 5(a). Here, SS and SE occur over a wide range of fluid properties. In contrast, SR appears only within a narrow parameter window and is highly sensitive to experimental conditions and fluid preparation, making it challenging. In addition, the predicted dependence of the normalized maximum streaming velocity, ⟨v~2⟩max⁡\langle\widetilde{\mathbf{v}}_2\rangle_{\max}, exhibits good agreement with the experimental data (see Figure 5b).

Image not extracted

Figure 5. (a) Comparison of theoretical and experimental dimensionless streaming velocity ⟨v~2⟩\langle\widetilde{\mathbf{v}}_2\rangle profiles across one quarter of the channel cross-section, illustrating streaming enhancement (SE, PEO 1 MDa, Dv=0.90D_v = 0.90, De=1.75D_e = 1.75), streaming suppression (SS, PEO 2 MDa, Dv=16.21D_v = 16.21, De=110.45D_e = 110.45), and streaming reversal (SR, PEO 0.4 MDa, Dv=16.21D_v = 16.21, De=6.25D_e = 6.25), compared with deionized water (DI, Dv=0D_v = 0, De=0D_e = 0). Arrows indicate streaming direction. (b) Theoretical variation of the dimensionless maximum streaming velocity ⟨v~2⟩max⁡\langle\widetilde{\mathbf{v}}_2\rangle_{\max} with DeD_e for PEO solutions, with experimental data shown as symbols. (c) Analytical prediction of the streaming coefficient CsC_s as a function of DeD_e and DvD_v; symbols denote experimental data. Red (Cs=1C_s = 1) and blue (Cs=0C_s = 0) dashed lines mark the SE–SS and SS–SR transitions, respectively.

Streaming Coefficient: regime characterization

To characterize the streaming transitions in viscoelastic fluids shown in Figure 4, the streaming coefficient CsC_s is introduced to quantify deviations from classical Rayleigh streaming in Newtonian fluids (see Eq. (88)). Streaming is enhanced for Cs>1C_s > 1, suppressed for 0≤Cs≤10 \le C_s \le1, and reversed for Cs<0C_s < 0. In the derivation of streaming (see Eq. (50)), the streaming coefficient is obtained as

Cs=2ρ0c02I1+2DeDvμs∗I2+2De2I33(1+De2)χ2(χ2+ξ2)ρ0c02μs∗(1+Dv)(89)C_s = \frac{2\rho_0 c_0^2 I_1 + 2DeDv\mu_s^* I_2 + 2De^2 I_3}{3(1+De^2)\chi^2(\chi^2+\xi^2)\rho_0 c_0^2\mu_s^*(1+Dv)} \tag*{(89)}

Here ρ0\rho_0 denotes the fluid density, μs∗=μs/μf\mu_s^* = \mu_s/\mu_f, μf\mu_f is the viscosity of the base Newtonian fluid (deionized water), I1I_1, I2I_2 and I3I_3 are functions of DvDv and DeDe, as given in Eqs. (51)–(53). The variation of CsC_s with DeDe and DvDv is presented in Figure 5(c). A regime of streaming enhancement (SE), characterized by Cs>1C_s > 1, is observed at low DeDe over the entire range of DvDv, where viscous effects dominate. At higher values of DvDv (Dv>12Dv > 12), increasing DeDe leads to a transition from SE to a narrow streaming suppression (SS) regime (0≤Cs≤10 \le C_s \le1), followed by streaming reversal (SR) (Cs<0C_s < 0), and subsequently a return to SS at high DeDe. In contrast, for Dv<12Dv < 12, the SE regime transitions into a broadened SS regime without the occurrence of reversal. The experimental data shown in Figure 5(c) fall within the same regimes predicted by the theoretical model, confirming quantitative consistency between theory and experiments. These trends identify Dv>12Dv > 12 as a necessary condition and 2<De<102 < De < 10 as a sufficient condition for the onset of SR, underscoring the coupled roles of viscous and elastic effects. To further elucidate the physical mechanisms underlying these transitions, the relative contributions of Reynolds stress (RES) and viscoelastic stress (VES) within the acoustic boundary layer are analyzed.

Streaming patterns and effect of Reynolds and viscoelastic stresses

Outer streaming is driven by inner streaming (Rayleigh [24]; Schlichting [26]); thus, the transitions observed in Figure 4 and the regimes in Figure 5(c) stem from changes within the boundary layer. The model shows that the time-averaged slip velocity ⟨v~2δ⟩s\langle\tilde{v}_2^\delta\rangle_s, which governs outer streaming, depends on fluid viscoelasticity. This slip velocity arises from nonlinearities in the boundary layer and modulates the bulk flow. In Newtonian fluids, inner streaming is driven by RES (Rayleigh [24]; Muller et al. [17]). In VE fluids, both RES and VES contribute to the acoustic body force facf_{ac}, which drives the streaming and is given by

fac=∇⋅ρ0⟨v1δv1δ+v1δv1d+v1dv1δ⟩+∇⋅τ{⟨v1δ⋅∇σ1⟩−⟨(∇v1δ)T⋅σ1⟩−⟨σ1⋅∇v1δ⟩}(90)f_{ac} = \nabla\cdot\rho_0 \left\langle\mathbf{v}_1^\delta\mathbf{v}_1^\delta+ \mathbf{v}_1^\delta\mathbf{v}_1^d + \mathbf{v}_1^d \mathbf{v}_1^\delta\right\rangle+ \nabla\cdot\boldsymbol{\tau} \left\{ \left\langle\mathbf{v}_1^\delta\cdot\nabla\boldsymbol{\sigma}_1 \right\rangle- \left\langle(\nabla\mathbf{v}_1^\delta)^T \cdot\boldsymbol{\sigma}_1 \right\rangle- \left\langle\boldsymbol{\sigma}_1 \cdot\nabla\mathbf{v}_1^\delta\right\rangle\right\} \tag*{(90)}

Here, σ1\boldsymbol{\sigma}_1 denotes the first-order viscoelastic stress. The right-hand side of Eq. (90) contains the divergence of RES and VES. In VE fluids, RES comprises viscous (RES, vv) and elastic (RES, veve) components. These stresses collectively drive the flow, which is opposed by viscosity, and this induces a momentum flux gradient, forming streaming rolls. Elasticity alters dissipation, modifying these gradients and enabling flow enhancement, suppression, or reversal (see Figure 4). To quantify this, the streaming slip velocity is considered as ⟨v~2δ⟩s=SRES,v+SRES,ve+SVES\langle\tilde{v}_2^\delta\rangle_s = S_{\mathrm{RES},v} + S_{\mathrm{RES},ve} + S_{\mathrm{VES}}.

The variation of ⟨v~2δ⟩s\langle\tilde{v}_2^\delta\rangle_s along with contributions from viscous RES (SRES,vS_{\mathrm{RES},v}), viscoelastic RES (SRES,veS_{\mathrm{RES},ve}), and VES (SVESS_{\mathrm{VES}}) as a function of DeDe for various DvDv is shown in Figure 6. The complete expressions for these contributions are provided in § 2.4. At Dv=20Dv = 20, ⟨v~2δ⟩s\langle\tilde{v}_2^\delta\rangle_s initially increases with DeDe, then decreases to zero, later reverses sign, and finally re-emerges in the original direction, consistent with transitions across SE, SS, SR, and SS (see Figure 4). SRES,vS_{\mathrm{RES},v} remains constant and positive, SRES,veS_{\mathrm{RES},ve} grows to a maximum then declines and turns negative near De≈10De \approx10. SVESS_{\mathrm{VES}} is always negative, peaking in magnitude before declining with increasing DeDe. At high DvDv (Figure 6a), the following findings are made: (i) at very low DeDe, ∣SRES,ve∣>∣SVES∣|S_{\mathrm{RES},ve}| > |S_{\mathrm{VES}}|, leading to SE. (ii) at low DeDe, ∣SVES∣≈∣SRES,v∣+∣SRES,ve∣|S_{\mathrm{VES}}| \approx|S_{\mathrm{RES},v}| + |S_{\mathrm{RES},ve}|, resulting in SS. (iii) at moderate DeDe, ∣SVES∣>∣SRES,v∣+∣SRES,ve∣|S_{\mathrm{VES}}| > |S_{\mathrm{RES},v}| + |S_{\mathrm{RES},ve}|, causing SR. (iv) at high DeDe, ∣SVES∣+∣SRES,ve∣≈∣SRES,v∣|S_{\mathrm{VES}}| + |S_{\mathrm{RES},ve}| \approx|S_{\mathrm{RES},v}|, leading to suppression in the reversed streaming. (v) at very high DeDe, ∣SVES∣|S_{\mathrm{VES}}| becomes negligible, highly suppressed streaming in the original direction is observed. In contrast, at low DvDv (Dv=1Dv = 1), SVESS_{\mathrm{VES}} is negligible throughout and ⟨v~2δ⟩s\langle\tilde{v}^{\delta}_{2}\rangle_{\mathrm{s}} stays positive across DeDe, showing only SE and SS (Figure 6b). Although SRES,veS_{\mathrm{RES},ve} turns negative for De>2De > 2, the condition ∣SRES,ve∣+∣SVES∣<∣SRES,v∣|S_{\mathrm{RES},ve}| + |S_{\mathrm{VES}}| < |S_{\mathrm{RES},v}| prevents reversal, therefore SS persists beyond De>2De > 2. Notably, both RES and VES arise from nonlinear interactions within the boundary layer, governed by the v1δv^{\delta}_{1} (see Eq. (90)), which can be attributed to viscoelastic shear waves [27, 11, 21, 20].

Image not extracted

Figure 6. Variation of the streaming slip velocity ⟨v~2δ⟩s\langle\tilde{v}^{\delta}_{2}\rangle_{\mathrm{s}} and the contributions of the viscous Reynolds stress (SRES,vS_{\mathrm{RES},v}), viscoelastic Reynolds stress (SRES,veS_{\mathrm{RES},ve}), and viscoelastic stresses (SVESS_{\mathrm{VES}}) with DeDe for (a) Dv=20Dv = 20 and (b) Dv=1Dv = 1.

Viscoelastic shear Waves: streaming patterns

The interaction between oscillatory perturbations along the xx-direction (v1dv^{d}_{1}) and the top and bottom walls generates VE shear waves [27, 11, 21, 20] that propagate from the walls into the bulk (see inset in Figure 7a). These waves, emerging from viscous dissipation and linked to acoustic energy loss, are characterized by an attenuation length (or boundary layer thickness) δve\delta_{ve} and a shear wavelength λve\lambda_{ve}. For Sp=δve/D≪1S_{p} = \delta_{ve}/D \ll1, the system is in the surface-loading regime [20], where shear waves decay before reaching the opposite wall, the xx-component of the shear wave is

Image not extracted

Figure 7. (a) Viscoelastic shear wave profiles along y/δfy/\delta_f for varying DeDe at Dv=20Dv = 20 and x~=0\tilde{x} = 0. Inset: schematic showing attenuation length δve\delta_{ve} and shear wavelength λve\lambda_{ve}. (b) Variation of α\alpha (=λve/2πδve= \lambda_{ve}/2\pi\delta_{ve}) with DeDe and DvDv. (c) Variation of storage modulus G~′\tilde{G}', loss modulus G~′′\tilde{G}'', and their ratio G~∗=G~′′/G~′\tilde{G}^{*} = \tilde{G}''/\tilde{G}' with DeDe for Dv=20Dv = 20 and Dv=1Dv = 1. (d) Phase lag θ=tan⁡−1(G~∗)\theta= \tan^{-1}(\tilde{G}^{*}) showing critical lag θc\theta_c marking the onset of SR. Magenta and orange dashed lines indicate SE–SS and SS–SR transitions.

v1,xδ=−v1d0cos⁡(kxx)e−χy/δfei(ωt−ξy/δf)(91)v^{\delta}_{1,x} = -v^{d0}_{1}\cos(k_{x}x)e^{-\chi y/\delta_{f}}e^{i(\omega t-\xi y/\delta_{f})} \tag*{(91)}

The yy-component of the shear wave is negligible as δfkx≪1\delta_{f}k_{x} \ll1, where δf=2μf/ρ0ω\delta_{f} = \sqrt{2\mu_{f}/\rho_{0}\omega} is the attenuation length in the base fluid. From Eq. (91), v1δ=v^1δeiωt\boldsymbol{v}^{\delta}_{1} = \hat{\boldsymbol{v}}^{\delta}_{1}e^{i\omega t}, where v^1δ\hat{\boldsymbol{v}}^{\delta}_{1} is the time-independent amplitude. The variation of v~1δ\tilde{v}^{\delta}_{1} (=v^1,xδ/∣v1d0∣= \hat{v}^{\delta}_{1,x}/|v^{d0}_{1}|) along yy at various DeDe is plotted in Figure 7(a). For De=0De = 0, the wave is overdamped; increasing DeDe yields underdamped behavior with varying δve\delta_{ve} and λve\lambda_{ve}.

We consider a complex propagation constant P=AF+iPFP = AF + iPF, with AF=1/δve=χ/δfAF = 1/\delta_{ve} = \chi/\delta_{f} quantifying amplitude decay, and PF=2π/λve=ξ/δfPF = 2\pi/\lambda_{ve} = \xi/\delta_{f} capturing phase variation. The ratio α=AF/PF\alpha= AF/PF along with DeDe and DvDv characterizes VE shear wave behavior (see Figure 7b). For α=1\alpha= 1, shear waves are overdamped, yielding streaming similar to viscous fluids. However, the underdamped waves (α<1\alpha< 1) correspond to streaming transitions. At high DvDv, SE occurs for 0.4<α<10.4 < \alpha< 1, SS for 0.28<α<0.40.28 < \alpha< 0.4, and SR for α≤0.28\alpha\leq0.28. At low DvDv, α>0.28\alpha> 0.28 for all DeDe, indicating absence of SR. Hence, a critical VE parameter is identified, αc=0.28\alpha_{c} = 0.28 that marks the onset of SR. However, how do these waves induce reversal at this threshold? To answer this, the energy dynamics of VE shear waves is analyzed.

Acoustic energy dissipation is key to generating momentum flux gradients that drive streaming Lighthill 1978. Like longitudinal waves, VE shear waves also transport energy. To understand their role, complex shear impedance Z=C+iRZ = C + iR is analyzed, where R∼G′′R \sim G'' (energy dissipation or loss modulus) and C∼G′C \sim G' (energy storage and release or storage modulus), linked to the complex shear modulus G=G′+iG′′G = G' + iG''. The G′G' and G′′G'' [12] are

G′=ρ0vs2(1−α2)(1+α2)2,G′′=2ρ0vs2α(1+α2)2.(92)G' = \frac{\rho_0 v_s^2(1-\alpha^2)}{(1+\alpha^2)^2}, \qquad G'' = \frac{2\rho_0 v_s^2\alpha}{(1+\alpha^2)^2}. \tag*{(92)}

Here, vs=ωλve/2πv_s = \omega\lambda_{ve}/2\pi is shear wave velocity. For α=1\alpha= 1, fluid behaves Newtonian. The moduli is normalized using loss modulus of base fluid (DI water): G~′=G′/Gf′′\tilde{G}' = G'/G''_f, G~′′=G′′/Gf′′\tilde{G}'' = G''/G''_f, and define loss tangent as tan⁡(θ)=G~′′/G~′=G~∗\tan(\theta) = \tilde{G}''/\tilde{G}' = \tilde{G}^{*}. A high tan⁡(θ)\tan(\theta) indicates rapid energy dissipation, while a low value signifies efficient storage and release.

The variation of G~′\tilde{G}', G~′′\tilde{G}'', and G~∗\tilde{G}^{*} with DeDe at high DvDv is presented in Figure 7(c). At very low DeDe, the response is strongly dissipative: G~′′≫G~′\tilde{G}'' \gg\tilde{G}', G~∗≫1\tilde{G}^{*} \gg1, and G~′′\tilde{G}'' remains constant, indicating a viscous-dominated regime with rapid shear wave relaxation (0.4<α<10.4 < \alpha< 1). This leads to SE via strong momentum flux gradients (see Figure 6). As DeDe increases, G~′\tilde{G}' peaks at De=1De = 1 then reduces due to reduced polymeric contributions at high relaxation times [7, 28], while G~′′\tilde{G}'' decreases monotonically, reaching a minimum near De=10De = 10. At De=1De = 1, G~′≈G~′′\tilde{G}' \approx\tilde{G}'' and G~∗≈1\tilde{G}^{*} \approx1, marking the SE–SS transition. Further increase in elasticity yields G~′′<G~′\tilde{G}'' < \tilde{G}' and G~∗<1\tilde{G}^{*} < 1, reducing dissipation and altering momentum flux. At moderate and high DeDe with α<αc\alpha< \alpha_c, G~′≫G~′′\tilde{G}' \gg\tilde{G}'', VE shear waves reverse flow by modifying time-averaged stresses and momentum gradients. However, at very high DeDe (De≫1De \gg1), α≈1\alpha\approx1 and G~′′>G~′\tilde{G}'' > \tilde{G}', the original flow direction resumes. At low DvDv (Dv=1Dv = 1), SE transitions to SS with increasing DeDe, but reversal is absent as G~′<G~′′\tilde{G}' < \tilde{G}'' throughout. In contrast, high DvDv amplifies G~′\tilde{G}', enabling reversal once a threshold is exceeded.

To quantify the interplay of moduli, the phase lag θ=tan⁡−1(G~∗)\theta= \tan^{-1}(\tilde{G}^{*}) is shown in Figure 7(e). A purely viscous response or viscous shear wave corresponds to θ=π/2\theta= \pi/2, while an ideal elastic response or elastic shear wave gives θ=0\theta= 0. At αc\alpha_c, tan⁡(θc)=G~∗≈0.60\tan(\theta_c) = \tilde{G}^{*} \approx0.60 gives θc≈31.03∘\theta_c \approx31.03^\circ (Figure 7(d)). Streaming remains enhanced or suppressed for θ>θc\theta> \theta_c, but reverses for θ<θc\theta< \theta_c. This highlights the need for a sufficiently high storage modulus relative to the loss modulus for flow reversal, linking viscoelasticity to energy dissipation and momentum flux modulation.

Conclusion

In conclusion, a theoretical framework is introduced for the first time to describe acoustic streaming in viscoelastic fluids confined within rectangular microchannels. The study demonstrates that acoustic streaming in a rectangular microchannel can be enhanced (SE), suppressed (SS), or reversed (SR) through controlled variation of fluid viscoelasticity. The streaming behavior is primarily governed by the Deborah number (DeDe) and the viscous diffusion number (DvDv), which together regulate the balance between Reynolds and viscoelastic stresses via energy dissipation in shear waves. The streaming transitions are characterized using G~∗\widetilde{G}^{*}, defined as the ratio of the loss to storage modulus of the shear wave. At high DvDv, streaming enhancement occurs for G~∗≫1\widetilde{G}^{*} \gg1, suppression for G~∗≈1\widetilde{G}^{*} \approx1, and reversal for G~∗<1\widetilde{G}^{*} < 1, whereas at low DvDv, only the transition from enhancement to suppression is observed. These viscoelasticity-driven streaming transitions offer new opportunities for controlled bioparticle manipulation and fluid pumping or mixing in microfluidic systems.

References

  1. [1]Bach, Jacob S. & Bruus, Henrik 2018 Theory of pressure acoustics with viscous boundary layers and streaming in curved elastic cavities. The Journal of the Acoustical Society of America 144 (2), 766–784.DOI
  2. [2]Bach, Jacob S. & Bruus, Henrik 2020 Suppression of acoustic streaming in shape-optimized channels. Physical Review Letters 124 (21).DOI
  3. [3]Barnkob, Rune, Cierpka, Christian, Chen, Minqian, Sachs, Sebastian, Mäder, Patrick & Rossi, Massimiliano 2021 Defocus particle tracking: a comparison of methods based on model functions, cross-correlation, and neural networks. Measurement Science and Technology 32 (9), 094011.DOI
  4. [4]Barnkob, Rune, Kähler, Christian J. & Rossi, Massimiliano 2015 General defocusing particle tracking. Lab on a Chip 15 (17), 3556–3560.
  5. [5]Bruus, Henrik 2012a Acoustofluidics 2: Perturbation theory and ultrasound resonance modes. Lab Chip 12 (1), 20–28.DOI
  6. [6]Bruus, Henrik 2012b Acoustofluidics 7: The acoustic radiation force on small particles. Lab on a Chip 12 (6), 1014.DOI
  7. [7]Donnikov, Alexander A., Fankhauser, Jonas & Dual, Jürg 2021a Nonlinear dynamics of a solid particle in an acoustically excited viscoelastic fluid. i. acoustic streaming. Physical Review E 104 (6).
  8. [9]Eckart, Carl 1948 Vortices and streams caused by sound waves. Physical Review 73 (1), 68–76.DOI
  9. [10]Faraday, Michael 1831 Xvii. on a peculiar class of acoustical figures; and on certain forms assumed by groups of particles upon vibrating elastic surfaces. Philosophical Transactions of the Royal Society of London 121, 299–340.
  10. [11]Ferry, John D. 1942 Mechanical properties of substances of high molecular weight. ii. rigidities of the system polystyrene-xylene and their dependence upon temperature and frequency. Journal of the American Chemical Society 64 (6), 1323–1329.DOI
  11. [12]Ferry, John D 1980 Viscoelastic properties of polymers. John Wiley & Sons.
  12. [13]Karlsen, Jonas T., Qiu, Wei, Augustsson, Per & Bruus, Henrik 2018 Acoustic streaming and its suppression in inhomogeneous fluids. Physical Review Letters 120 (5).DOI
  13. [14]Lee, Chun P. & Wang, Taylor G. 1990 Outer acoustic streaming. The Journal of the Acoustical Society of America 88 (5), 2367–2375.DOI
  14. [16]Milliken, William J. & Powell, Robert L. 1990 Finite-amplitude ultrasonic measurements of polyethylene oxide and polyacrylamide solutions. The Journal of the Acoustical Society of America 88 (3), 1547–1554.DOI
  15. [17]Muller, Peter Barkholt, Barnkob, Rune, Jensen, Mads Jakob Herring & Bruus, Henrik 2012 A numerical study of microparticle acoustophoresis driven by acoustic radiation forces and streaming-induced drag forces. Lab on a Chip 12 (22), 4617.DOI
  16. [18]Muller, P. B., Rossi, M., Marín, Á. G., Barnkob, R., Augustsson, P., Laurell, T., Kähler, C. J. & Bruus, H. 2013 Ultrasound-induced acoustophoretic motion of microparticles in three dimensions. Physical Review E 88 (2).
  17. [19]Oldroyd, James G 1950 On the formulation of rheological equations of state. Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences 200 (1063), 523–541.DOI
  18. [20]Ortín, Jordi 2020 Stokes layers in oscillatory flows of viscoelastic fluids. Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences 378 (2174), 20190251.
  19. [21]Pascal, H. 1989 Propagation of disturbances in a non-newtonian fluid. Physica D: Nonlinear Phenomena 39 (2–3), 262–266.DOI
  20. [22]Powell, R. L. 1982 Acoustic streaming reversal by a finite amplitude sound wave in a non-newtonian fluid. The Journal of the Acoustical Society of America 71 (5), 1118–1123.
  21. [23]Qiu, Wei, Joergensen, Jonas Helboe, Corato, Enrico, Bruus, Henrik & Augustsson, Per 2021 Fast microscale acoustic streaming driven by a temperature-gradient-induced nondissipative acoustic body force. Physical Review Letters 127 (6).DOI
  22. [24]Rayleigh, Lord 1884 On the circulation of air observed in kundt’s tubes, and on some allied acoustical problems. Philosophical Transactions of the Royal Society of London 175, 1–21.
  23. [25]Sadhal, S. S. 2012 Acoustofluidics 13: Analysis of acoustic streaming by perturbation methods. Lab on a Chip 12 (13), 2292.DOI
  24. [26]Schlichting, Hermann 1932 Berechnung ebener periodischer grenzschicht-strommungen [calculation of plane periodic boundary layer streaming]. Phys. Zcit. 33, 327–335.
  25. [27]Stokes, George Gabriel 2009 Mathematical and Physical Papers. Cambridge Library Collection – Mathematics 1. Cambridge: Cambridge University Press.
  26. [28]Sujith, T., Malik, L. & Sen, A.K. 2024 Fluid viscoelasticity affects ultrasound force field-induced particle transport. Journal of Fluid Mechanics 1000.DOI
  27. [29]Van Assche, David, Reithuber, Elisabeth, Qiu, Wei, Laurell, Thomas, Henriques-Normark, Birgitta, Mellroth, Peter, Ohlsson, Pelle & Augustsson, Per 2020 Gradient acoustic focusing of sub-micron particles for separation of bacteria from blood lysate. Scientific Reports 10 (1).DOI
  28. [30]Vargas, C., Campos-Silva, I., Méndez, F., Arcos, J. & Bautista, O. 2022 Acoustic streaming in maxwell fluids generated by standing waves in two-dimensional microchannels. Journal of Fluid Mechanics 933.DOI
  29. [31]Wiklund, Martin, Green, Roy & Ohlin, Mathias 2012 Acoustofluidics 14: Applications of acoustic streaming in microfluidic devices. Lab on a Chip 12 (14), 2438.DOI

Paper details

vlnc:W_dytje2rc
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents