betaFeedback

WorksPhysics and Astronomy

Improving terahertz-detection sensitivity of 8x8 FET arrays through liquid-nitrogen cooling in a compact low-noise cryostat

Abstract

We show that the sensitivity of antenna-coupled field-effect transistors (FETs) to terahertz (THz) radiation improves continuously with decreasing temperature. The noise-equivalent power (NEP) of 540 GHz patch-antenna-coupled FETs decreases as temperature reduces to 20 K. We project NEP values approaching 1 to 2 pW/sqrt(Hz) under efficient power coupling conditions (e.g., using a superstrate Si-lens), which is comparable to superconducting niobium transition-edge sensors (TESs) at 4 K. Building on these findings, a compact, low-noise, liquid-nitrogen-cooled (77 K) FET-based direct (incoherent) THz-power sensing system} for spectroscopy applications was realized. Here, an 8x8 pixel-binned detector array fabricated in a commercial 65-nm Si-CMOS process, was optimized for operation in the 2.85 to 3.4 THz band. Characterization was performed in the focal plane of a 2.85-THz quantum-cascade laser delivering approx. 2~mW of THz power. A linear dynamic range exceeding 67 dB was achieved without saturation (for 1~Hz-detection bandwidth). The system provides a -3 dB readout bandwidth of 5 MHz, exceeding that of conventional thermal detectors (typically 1 kHz). Combined with its broad temperature operability 20 K to 300 K and compact design, the system is particularly well suited for space- and payload-constrained platforms such as balloon- and satellite-based missions, where deep cryogenic cooling is impractical.

J. Holstein, A. Hof and H. G. Roskos are with the Physikalisches Institut, Johann Wolfgang Goethe-Universität, DE-60438 Frankfurt am Main, Germany (e-mail: [email protected]).

A. Lisauskas is with (i) the Institute of Applied Electrodynamics and Telecommunications, Vilnius University, LT-10257 Vilnius, Lithuania, (ii) Center for Physical Sciences and Technology, LT-10257 Vilnius, Lithuania, (iii) Physikalisches Institut, Johann Wolfgang Goethe-Universität, DE-60438 Frankfurt am Main, Germany.

N. K. North, S. Kondawar, M. Salih, L. Li, E. H. Linfield, A. G. Davies, J. R. Freeman, and A. Valavanis are with the School of Electronic and Electrical Engineering, University of Leeds, Leeds LS2 9JT, United Kingdom (e-mail: [email protected]).

D. B. But is with (i) CENTERA, Institute of High Pressure Physics PAS, 01-142 Warsaw, Poland, (ii) IB1, National Centre for Nuclear Research Świerk, 05-400 Otwock, Poland

Introduction

The terahertz (THz) frequency range of the electromagnetic spectrum (0.3–10 THz) has attracted growing attention over the past two decades, with potential applications including high-speed wireless communication, non-destructive testing, imaging, chemical or biological sensing [1], and gas spectroscopy [2, 3]. However, the ∼1\sim1–5 THz band remains technologically challenging owing to the limited availability of powerful THz sources and sensitive detectors or mixers that can operate without liquid-helium cooling. This is particularly important for balloon-borne [4] and satellite-borne [5] instrumentation, where the cooling infrastructure is constrained by strict limitations on payload mass, volume, and power consumption. Cryogenically-cooled bolometers are extensively utilized for terahertz sensing applications, owing to their high sensitivity (low Noise Equivalent Power, NEP) (see Table I). However, the main limitation of thermal detectors is their comparably slow detection mechanism [6]. As such, the absence of fast and sensitive detectors—especially those capable of continuous, cryogen-free operation—remains a significant barrier to the broader application and integration of THz systems within this frequency range. In this context, we present a compact, low-noise, liquid-nitrogen (LN2_2)-cooled power detection system with a −3 dB bandwidth of approximately 5 MHz (mainly limited by the chosen readout electronics), capable of detecting THz radiation emitted by a quantum-cascade laser (QCL) at 2.85 THz. This is enabled by the core element of the system: an 8×88 \times8 antenna-coupled field-effect transistor (FET) array employing a pixel binning technique, as reported in [7]. Over the past decades, THz detection using FETs has evolved from fundamental research devices [8, 9, 10] into high-performance detectors covering the entire terahertz (THz) frequency range [11, 12, 13]. Applications range from imaging [14, 15, 16, 17], spectroscopy [7], [18, 19, 20], tracking of ultrashort pulses [21], [22] or passive detection of thermal radiation [23], [24]. FETs can be employed either as direct THz power detectors or as heterodyne mixers [25], [26], operating effectively in both room temperature and cryogenic environments [27], [28]. Owing to their electronic detection mechanism—based on the excitation of plasma waves in the two-dimensional electron gas (2DEG) of the transistor channel—FETs exhibit an intrinsically high detection speed, with response times reported down to 12 ps [22] corresponding to 10s of GHz achievable modulation bandwidth.

A key advantage over established electronic THz detector technologies, such as commercially available Schottky-diode technology, is their compatibility with widely used semiconductor platforms including AlGaN/GaN [29], AlGaAs/GaAs [12], or Si-CMOS [7], [10], [30]–[35]. Graphene-based FETs are also a currently-emerging technology [36]–[39]. This technological flexibility enables, for example, the fabrication of Si-CMOS-based FETs using mature commercial foundry processes, offering high scalability and process reliability. In the detectors presented in this work, the 65-nm CMOS technology node provided by Taiwan Semiconductor Manufacturing Company (TSMC) was utilized. This allows not only for the realization of individual detectors, but also for the cost-efficient production of large-scale detector arrays as e.g., required for THz camera systems [7], [40]–[42]. These advantages make FET-based terahertz detectors a promising candidate for future scientific and industrial applications.

This work is structured in the following way. Before presenting a detailed analysis of LN2_2-cooled FETs for THz-QCL applications, we highlight the potential of cryogenic cooling through a systematic study that quantitatively investigates the NEP of a Si-CMOS FET coupled to a patch antenna resonant at 540 GHz.

The optical NEP of this detector at room temperature, when coupled to a superstrate Si-lens, can be as low as 16 pW/Hz\sqrt{\mathrm{Hz}} [19]. In the presented experiment, no Si-lens was applied. However, based on the experimental beam conditions, cross-sectional NEP on the order of ∼25 pW/Hz\sqrt{\mathrm{Hz}} was determined at room temperature for the 540 GHz-detector, which is in good agreement with our previously published work [19] [Table 1: Case A (without lens)]. We observe a continuous NEP-improvement down to 20 K. Specifically, we report a fourfold improvement at 77 K, which is in close agreement with previously published study investigating TeraFETs fabricated in 90 nm Si-CMOS technology. Based on our results obtained with the TeraFET detector resonant at 540 GHz and operated at 20 K, we observed up to a fifteenfold improvement in NEP compared to room-temperature operation, corresponding to an expected NEP in the range of 1–2 pW/Hz\sqrt{\mathrm{Hz}}, assuming efficient power coupling — for instance, when using a superstrate silicon lens coupled to the patch antenna. This performance is comparable to that of state-of-the-art superconducting transition-edge sensor (TES) bolometers operated at 4 K. In Table I, we

finally summarize the most important detector parameters investigated here and compare with other state-of-the-art power detector technologies available for the frequency range around 3 THz.

FET-based THz detectors

Current TeraFET detectors reach optical NEPs1 down to 10–20 pW/Hz\sqrt{\mathrm{Hz}} in the frequency range up to 1 THz at room temperature [19], [43]–[45] — a sensitivity level suitable for many practical applications. For applications in the frequency range above ∼2 THz, where THz QCL sources can be employed, the sensitivity of available electronic detector (Schottky and FET) technologies decreases. However, while Schottky-based detectors experience strong frequency related roll-off due to large junction capacitance, FET sensitivity is expected to show less pronounced roll-off behavior [13], [46].

The effect of cooling TeraFET detectors to cryogenic temperatures is twofold. First, the signal magnitude increases due to a more efficient mixing process [27], which is driven by the enhanced non-linearity of the gated channel’s carrier density n(VGS)n(V_{\mathrm{GS}}) around the transistor’s threshold voltage. Second, thermal noise from the FET’s Ohmic resistance is reduced, according to Eq. (3). Mathematically, n(VGS)n(V_{\mathrm{GS}}) can be described with the Unified Charge Control Model (UCCM) [47]. In our implementation, electromagnetic THz radiation is coupled to the transistor between source and gate electrode2 (see Figure 1). This coupling scheme excites strongly damped carrier-density modulations (plasma waves) that propagate from the source into the gated channel.

Figure 1. a) Cross-sectional view of the patch-antenna implementation, representing the unit cell of the 8 × 8 TeraFET array (not to scale; graphic adapted from [48]). Relevant dimensions and permittivities are indicated. b) Top view of the transistor layout. The strongly doped p+p^{+}-well region, shown in pink, was introduced to pin the body potential to source ground (guard ring). The dimensions of the square-shaped ring are d1,p-well=6 μmd_{1,\mathrm{p\text{-}well}} = 6\,\mu\mathrm{m} and d2,p-well=1 μmd_{2,\mathrm{p\text{-}well}} = 1\,\mu\mathrm{m}. Depth of the p+p^{+}-well is estimated as ∼60 nm\sim60\,\mathrm{nm} and doping density around 2.5×1019 cm−32.5 \times10^{19}\,\mathrm{cm}^{-3} (compare [50]).

The nonlinear mixing of these plasma waves in the channel results in a DC-signal between source and drain electrodes that is proportional to the incident terahertz power PTHzP_{\mathrm{THz}}:

ΔVDS,THz=−VTHz24∂ln⁡[Rch(VGS)]∂VGSf(ωTHz,τp)∝PTHz(1)\Delta V_{\mathrm{DS,THz}}=-\frac{V_{\mathrm{THz}}^{2}}{4}\frac{\partial\ln[R_{\mathrm{ch}}(V_{\mathrm{GS}})]}{\partial V_{\mathrm{GS}}}f(\omega_{\mathrm{THz}},\tau_{\mathrm{p}})\propto P_{\mathrm{THz}} \tag*{(1)}
ΔVDS,THz=VTHz24∂ln⁡[n(VGS)]∂VGSf(ωTHz,τp)(2)\Delta V_{\mathrm{DS,THz}}=\frac{V_{\mathrm{THz}}^{2}}{4}\frac{\partial\ln[n(V_{\mathrm{GS}})]}{\partial V_{\mathrm{GS}}}f(\omega_{\mathrm{THz}},\tau_{\mathrm{p}}) \tag*{(2)}

where f(ω,τp)=1+2ωτp/1+(ωτp)2f(\omega,\tau_{\mathrm{p}})=1+2\omega\tau_{\mathrm{p}}/\sqrt{1+(\omega\tau_{\mathrm{p}})^2} is the channel’s conversion ability relative to a low-frequency pure resistive mixing process [30], and τp\tau_{\mathrm{p}} is the momentum scattering time.3 The rectified signal (ΔVDS\Delta V_{\mathrm{DS}}) is proportional to the incident power PTHzP_{\mathrm{THz}} within a certain linear regime. At higher power levels, this linear response transitions into a super-linear regime (ΔVDS∝PTHz2\Delta V_{\mathrm{DS}} \propto P_{\mathrm{THz}}^{2}), within the sub-threshold operation range before eventually going into saturation. In contrast, above the threshold, the response shifts directly from the linear regime into saturation without exhibiting the intermediate super-linear behavior [22].

An unbiased source–drain condition (VDS,ext=0 VV_{\mathrm{DS,ext}} = 0\,\mathrm{V}) has been shown to yield the highest signal-to-noise ratio (SNR) compared to actively biased operation [49]. In this unbiased case, thermal Johnson–Nyquist noise is the dominant noise source,

VJN=4kBTDetRDS(3)V_{\mathrm{JN}} = \sqrt{4k_{\mathrm{B}}T_{\mathrm{Det}}R_{\mathrm{DS}}} \tag*{(3)}

where kBk_{\mathrm{B}} is the Boltzmann constant, TDetT_{\mathrm{Det}} is detector temperature and RDSR_{\mathrm{DS}} is the transistor’s source–drain resistance, determined experimentally from II–VV characterization. Both the enhanced rectification efficiency and the reduction of thermal noise contribute to an improved NEP under cryogenic operation.

Detector implementation

Two FET-based THz detector designs were investigated in this work, using TSMC’s 65-nm foundry process (CLN65LP, type 1.2VmLowVtMOS): a single-patch antenna for 540 GHz operation, and an 8 × 8 patch-antenna array for 2.85 THz operation. The 540-GHz detector used a patch antenna area of (138×40) μm2(138 \times40)\,\mu\mathrm{m}^{2}, as visualized in [48] and had a transistor channel width Wch=1 μmW_{\mathrm{ch}} = 1\,\mu\mathrm{m}, and gated length Lg=60 nmL_{\mathrm{g}} = 60\,\mathrm{nm}. The patch-antenna’s simulated directivity is ∼5.8 dBi\sim5.8\,\mathrm{dBi}. This leads to a low optical coupling efficiency in the experimental work described later, as the effective antenna area is small compared to the Gaussian focal point of the off-axis parabolic (OAP) mirror with a reflected focal length (RFL) of 3-inch (Full-Width-at-Half-Maximum, FWHM ≈1.3 mm\approx1.3\,\mathrm{mm}). Under these focal conditions, we expect approximately 5% of the incident power to be coupled into the antenna (technique presented in [48]).

The 2.85 THz detector used an 8 × 8 binned-element configuration with active area (600×600) μm2(600 \times600)\,\mu\mathrm{m}^{2} as reported in [7]. A cross-sectional view of the unit-cell element is visualized in Figure 1. Transistor channel parameters Wch=0.2 μmW_{\mathrm{ch}} = 0.2\,\mu\mathrm{m} and gated length 60 nm were used. Each patch-antenna in the array had area (15×15) μm2(15 \times15)\,\mu\mathrm{m}^{2}, with the active patch placed in layer M8 (height, h=2.4 μmh = 2.4\,\mu\mathrm{m} above the ground plane) as indicated in the diagram. A smaller (13×13) μm2(13 \times13)\,\mu\mathrm{m}^{2} patch is placed in the M10-layer (h=8.41 μmh = 8.41\,\mu\mathrm{m}) to satisfy minimum metal fill-factor rules for foundry processing, without significantly modifying the (simulated) antenna field pattern. To ensure a consistent electrostatic environment and to minimize noise contributions from and to all rectifying transistors, a strongly doped p+p^{+}-well guard ring is implemented around each nn-MOSFET. This ring electrically connects both the source and body terminals to the global ground potential. The high doping concentration of the p+p^{+}-well ensures sufficient conductivity even at cryogenic temperatures, thereby preserving effective grounding and suppressing latch-up effects by inhibiting the formation of parasitic current paths in the pp-substrate. Furthermore, the guard ring stabilizes the body potential and mitigates carrier freeze-out in the inversion layer near the source junction—an essential condition for reliable operation at low temperatures. The dimensions of the applied square shaped ring are d1,p-well=6 μmd_{1,\mathrm{p\text{-}well}} = 6\,\mu\mathrm{m} and d2,p-well=1 μmd_{2,\mathrm{p\text{-}well}} = 1\,\mu\mathrm{m}.4

A summary of the detector element’s spectral response is shown in Figure 2, with continuous data obtained from a thermal source using a Bruker fourier-transformer and discrete responsivity measurements taken using THz-QCLs at four emission frequencies (2.5 THz, 2.85 THz, 3.4 THz and 3.6 THz). Results at 2.85 THz, 3.4 THz and 3.6 THz were acquired using THz QCLs in semi-insulating surface plasmon waveguides, with the data at 2.85 THz and 3.4 THz having been reproduced from [7]. The 2.5 THz-QCL data-point was acquired using a frequency rescaled design adapted from [52], and packaged into a double metal waveguide. We attribute the relatively low signal to poor beam quality in the focal plane resulting from the double-metal waveguide. For all measurements shown in Figure 2, the respective detector element was operated at room temperature. Nonetheless, the presented data illustrate that the peak of spectral response qualitatively agrees with model predictions. The quantitative and statistical analysis requires extensive modification of THz sources, allowing formation of Gaussian beams (or a calibrated Black-Body high temperature sources, if measured using FTIR spectrometry).

Figure 2. Experimental and simulated THz spectral response of the patch-antenna coupled FET shown in Figure 1 at VGS=0.55V_{\mathrm{GS}} = 0.55 V. Stars: Normalized responsivity taken from measurements with 8 × 8 detector using THz-QCLs at four frequencies (2.5 THz, 2.85 THz, 3.4 THz and 3.6 THz). Data at 2.85 THz and 3.4 THz was reproduced from [7]. Red Line: Spectral response of a single FET-detector (unit cell of the 8 × 8-detector) coupled to a superstrate Si-lens as introduced in [19]. Spectral response was determined using a Michelson interferometer with a thermal (Globar) source (vendor: Bruker Corp.). Blue: Simulated responsivity of the patch antenna element. The antenna structure’s impedance and efficiency was simulated using CST Studio Suite and the transistor’s terahertz response was modeled using an in-house hydrodynamic model implemented in Keysight’s Advanced Design System (ADS-HDM) as presented in [51] and [48]. All measurements presented within this graph were acquired, while the detector element was operated at room-temperature.

Packaging and readout electronics

The respective detectors were mounted on in-house designed Al-based printed circuit boards (PCBs) with high thermal conductivity (>2>2 W mK−1^{-1}, thickness 1.5 mm) using a thermally curable, two-component epoxy adhesive (EPO-TEK 353ND). Electrical connections between the detector electrodes and the PCB were established via Al-wire bonding. The resulting signals were then routed via twisted pair cables from the detector PCB to separate PCBs containing the subsequent amplifier and buffer stage. The amplifier chain was operated at room temperature, while the detector-element was actively cooled by the cryostat coldfinger. In both configurations, the electronic readout/buffer circuitry consists of junction field-effect transistor (JFET)- and Operational Amplifier (OPA)-based components (inset in Figure 3), and was designed to achieve low-noise operation and suppress 1/f1/f-noise contributions. First, the rectified signal is fed into a JFET-stage consisting of two JFETs, grown on the same substrate for maximized similarity in their electronic properties. These were biased at the lowest-noise operating point (determined by the choice of the top resistors). For the temperature-dependent measurements at 540 GHz, the signal was buffered by a Source-follower stage as presented in [7], based on the LSK489 JFET-pair (SOT-23-6 package, vendor: Linear Systems). The buffer stage was followed by two low-noise amplifier stages (Gain 10 each, Texas Instruments OPA211/1611). In case of the compact LN2_2-cooled cryostat, the first stage was implemented as a low-noise, high-input impedance composite ampli-

Figure 3. Experimental noise spectral amplitude of both room-temperature and LN2_2-cooled 8 × 8 FET array operation at VGS=0.55V_{\mathrm{GS}} = 0.55 V measured with a Tektronix DPO4104 oscilloscope. (Inset) Schematic of the electronic amplifier circuitry (Low Noise, High Input Impedance Composite Amplifier, adapted from [53]) consisting of a JFET-input stage and a low-noise amplifier followed by a second low-noise amplifier stage (total gain GV=100G_{\mathrm{V}} = 100). The complete amplifier chain is not actively cooled, while the detector is operated at 77 K. The amplifier chain is enclosed in a metal shielding box (see Figure 4).

fier, adapted from [53], visualized in Figure 3. The input-referred noise of our low-noise, high-input impedance composite amplifier implementation was determined with 1.51.5 nV/Hz\sqrt{\mathrm{Hz}}, which is below the thermal noise of about 11 kΩ resistance at room temperature of 4.054.05 nV/Hz\sqrt{\mathrm{Hz}} expected from Eq. (3). To realize the circuit, the JFET-pair JFE2140 (SOIC-8 package, vendor: Texas Instruments) in combination with an OPA211 followed by a second OPA211 stage was applied. In both implementations, the second amplifier stage’s output was fed to a SMA connector, which was connected to the respective lab measurement equipment (compare Figure 5). For 540 GHz-characterizations, the total voltage gain was GV=70G_{\mathrm{V}} = 70 (compare [7]), while GV=100G_{\mathrm{V}} = 100 was determined for the LN2_2-configuration. All relevant electrical potentials, including the GND/Source and VGSV_{\mathrm{GS}}, were supplied from a common in-house designed power supply PCB. The achievable modulation bandwidth f−3dB≈5f_{-3\mathrm{dB}} \approx5 MHz of the detector and amplifier electronics was estimated via measurement of noise spectral amplitude density spectrum using a Tektronix DPO4104 oscilloscope as shown in Figure 3. Due to the low input-referred noise of the amplifier chain, the detector’s thermal noise contribution dominates to the overall noise spectral amplitude at 77 K. We estimate the stage to add less than 1 dB to the final noise spectral amplitude.

Figure 5. Experimental setup used for FET detector characterization at cryogenic temperatures at 540 GHz. Terahertz radiation generated using an RPG ZTX750 multiplier (×36) (vendor: Radiometer Physics GmbH, Germany) was guided through an optical system onto the detector (without Si-lens) inside a closed cycle cryostat. For this measurement, an OAP with RFL of 3 inch was used as the final focusing element due to space constraints. The biasing/readout scheme was same for the 2.85 THz-QCL based setup, while the setup geometry can be seen in Figure 6.

Implemented cryogenic systems

Two cryogenic systems were used for this work: a closed-cycle cryostat for measurement of responsivity as a continuous function of temperature, and a LN2_2-cooled cryostat for QCL power measurements. The detector-PCB was mechanically mounted onto the metallic coldfinger of the respective cooling system. For the helium-based closed-cycle cryostat (vendor: LakeShore Cryotronics), precise control of the coldfinger temperature was achieved via two independent thermal sensors and a heater element. Temperature regulation was managed by a LakeShore Cryotronics Model 330 controller. Using a multiplexer circuit (TMUX136, vendor: Texas Instruments), the drain output could either be accessed directly, bypassing the amplifier electronics to determine the temperature-dependent II–VV characteristic, or routed through the low-noise amplifier chain for terahertz detection experiments. The compact LN2_2-cooled system, designed for QCL power measurements, was based on a commercial dewar system (vendor: PerkinElmer) providing both easy-access cooling and vacuum capabilities and is shown in Figure 4. To enable optical terahertz transmissive access, the original CaF2_2 window was replaced by a 20 µm-thick THz-transmissive polypropylene foil stretched within an in-house designed holder to ensure proper vacuum sealing. The amplifier electronics were housed in a metallic enclosure at the rear of the dewar. We determined an approximate cooling time of 1.5–2 h for the detector system to reach thermal equilibrium with the 77 K coldfinger, as measured by the stabilization time of IDSI_{\mathrm{DS}} under a constant bias of VDS=1V_{\mathrm{DS}} = 1 mV and VGS=0.55V_{\mathrm{GS}} = 0.55 V.

Photograph of the LN2-cooled detector system and its internal components

Figure 4. Photograph of the LN2_2-cooled detector system and its internal components. The first inset shows the aluminum-based PCB mounted on the dewar’s cold finger, carrying the detector die. The second inset provides a zoomed-in view of the 8 × 8 pixel binned TeraFET detector array. The resulting effective active detector area is approximately (600 × 600) µm2^2 (introduced in [7]). The housing provides access for liquid nitrogen cooling (top) and includes a vacuum port compatible with external pumping systems (left). Buffer and amplifier electronics (see Figure 3) are housed in a shielded metal enclosure to suppress electromagnetic interference from the laboratory environment. Power supply, on/off switch, and the SMA output connector are located on the rear side of the shielding box.

Low-temperature responsivity analysis

A comparable experimental apparatus was used for FET-detector characterization at 540 GHz and 2.85 THz, albeit with different THz sources in each case. 540 GHz-radiation was generated by multiplying a 15 GHz oscillator signal by (×36) using an RPG ZTX750 multiplier (vendor: Radiometer Physics GmbH, Germany). The emitted signal was amplitude modulated using an input square-wave reference for lock-in detection. The available PTHz=50P_{\mathrm{THz}} = 50 µW was measured using a pyroelectric detector (THz 10 HS, vendor: SLT GmbH [54]), calibrated by Physikalisch-Technische Bundesanstalt (PTB, Braunschweig, Germany).

The 2.85 THz measurements were performed using a QCL adapted from the design in [52], as in our previous work [7]. The QCL was mounted in a helium flow cryostat (vendor: Janis/LakeShore Cryotronics) equipped with 3-mm-thick HDPE windows. The QCL temperature was set at 20 K, while being driven with either 700 mA or 808 mA pulses, with 5 % and 50 % duty cycle pulses generated by laboratory pulse generator (Agilent 8114A). The corresponding THz power was determined using a calibrated photoacoustic power meter (vendor: TK Instruments Ltd., UK) at the detector position shown in Figure 6. In case of 50 % duty-cycle pulses, a QCL output power of PTHz(808 mA)=2.1P_{\mathrm{THz}}(808\ \mathrm{mA}) = 2.1 mW was measured, whereas for 5 %-duty-cycle operation, PTHz(700 mA)=P_{\mathrm{THz}}(700\ \mathrm{mA}) = 0.36 mW and PTHz(808mA)=0.43mWP_{\mathrm{THz}}(808\mathrm{mA})=0.43\mathrm{mW} were measured.5 The QCL’s emission spectrum was found to be a single mode at 2.85 THz, using a commercial FTIR-system (Bruker IFS/66). For the 540 GHz setup, the detector was initially characterized as a function of temperature using the closed-cycle cryocooler system apparatus described in subsection II-C and shown in Figure 5. The radiation emitted by the respective THz-source was guided through a quasi-optical system consisting of two 90° OAPs onto the respective detector. For the 540 GHz-system, RFLs of 4 inch/3 inch and 2 inch-diameter were used (see Figure 5), while the 2.85 THz-system used OAPs with a diameter of 3 inch and RFLs of 7 inch/7 inch (see Figure 6). For the 540 GHz system, the single patch-antenna coupled detector was mounted within a continuously temperature tunable closed-cycle cryostat. For the 2.85 THz-characterization, the 8 × 8 detector was operated inside the liquid nitrogen cooled cryostat.

Normalized experimental beam profile and experimental setup

Figure 6. (a) Normalized experimental beam profile data taken at the focal position, determined using an uncooled microbolometer camera (Swiss Terahertz Rigi S2, (160 × 120) px at 25 µm pitch). (b) Picture of the experimental setup used for detector characterization. Emission from a THz-QCL mounted in a cryostat is guided through off-axis parabolic mirror optics (Diameter: 3 inch, RFL: 7 inch). The experimental beam focus is marked with an iris. The terahertz power PTHzP_{\mathrm{THz}} was measured at the focal position using a Thomas Keating photoacoustic power meter.

After passing the respective amplifier stage with voltage gain GVG_{\mathrm{V}}, the terahertz rectified voltage was demodulated using an Ametek DSP 7265 lock-in amplifier and its time-averaged amplitude VDS,LIAV_{\mathrm{DS,LIA}} was recorded. Voltage-responsivity RV,opt\mathcal{R}_{\mathrm{V,opt}} was calculated via

RV,opt=αLIA⋅ΔVDS,LIAPTHz⋅GV(4)\mathcal{R}_{\mathrm{V,opt}}=\frac{\alpha_{\mathrm{LIA}}\cdot\Delta V_{\mathrm{DS,LIA}}}{P_{\mathrm{THz}}\cdot G_{\mathrm{V}}} \tag*{(4)}

where αLIA=π/2\alpha_{\mathrm{LIA}}=\pi/\sqrt{2} accounts for the square-wave modulated signal sensed via lock-in detection and PTHzP_{\mathrm{THz}} denotes the total available THz power incident on the detector.

An alternative metric, the cross-sectional responsivity RV,CS\mathcal{R}_{\mathrm{V,CS}}, relates the effective antenna area to the physical dimensions of the focal spot as described in [31]. For the single-patch antenna, the effective antenna area is Aeff=DλTHz2/(4π)A_{\mathrm{eff}}=D\lambda_{\mathrm{THz}}^{2}/(4\pi), where DD is the simulated antenna directivity.6 The experimental beam profile in the focal plane of the 2.85 THz-setup is shown in Figure 6. It was acquired using an uncooled microbolometer camera (Swiss Terahertz Rigi S2, (160 × 120) px at 25 µm pitch). The focal dimensions of the beam profile were measured as FWHMx=0.40mm\mathrm{FWHM}_{x}=0.40\mathrm{mm}, FWHMy=0.41mm\mathrm{FWHM}_{y}=0.41\mathrm{mm} using a numerical fitting routine. The presented beam profile was measured at IQCL=700mAI_{\mathrm{QCL}}=700\mathrm{mA} using 50 % duty-cycle pulses.7

The optical NEP was calculated from Eq. (4) and Eq. (3) via

NEPopt/CS,JN/exp=VJNRV,opt/CS≈VN,expRV,opt/CS(5)\mathrm{NEP}_{\mathrm{opt/CS,JN/exp}}=\frac{V_{\mathrm{JN}}}{R_{\mathrm{V,opt/CS}}}\approx\frac{V_{\mathrm{N,exp}}}{R_{\mathrm{V,opt/CS}}} \tag*{(5)}

In Eq. (5), VN,expV_{\mathrm{N,exp}} denotes the experimentally measured noise spectral density under the given laboratory conditions. Although we observe VJN≈VN,expV_{\mathrm{JN}}\approx V_{\mathrm{N,exp}} at room temperature, as suggested in [49], deviations from this expectation become noticeable at LN2_2 temperatures. We attribute these deviations to the fact that, in our experimental setup, the readout electronics remain at room temperature while the detector temperature TDetT_{\mathrm{Det}} is cooled to cryogenic temperatures (e.g., 77 K). As is common practice in the literature to report NEPexp,JN\mathrm{NEP}_{\mathrm{exp,JN}}, both values will be provided in the following discussion. Another important Figure of Merit is experimental signal-to-noise ratio (SNR) for a given lock-in integration time TC≈1/(4Δf)T_{\mathrm{C}}\approx1/(4\Delta f), where Δf\Delta f is the equivalent noise bandwidth (ENBW),8 calculated via

SNR=ΔVDS,LIA,THz onΔVDS,LIA,THz off=PTHzNEPopt⋅Δf(6)\mathrm{SNR}=\frac{\Delta V_{\mathrm{DS,LIA,THz\,on}}}{\Delta V_{\mathrm{DS,LIA,THz\,off}}}=\frac{P_{\mathrm{THz}}}{\mathrm{NEP}_{\mathrm{opt}}\cdot\sqrt{\Delta f}} \tag*{(6)}

The respective dynamic range can be defined via:

DNR(TDet)=max⁡VGS,PTHz,Δf(SNR)(7)\mathrm{DNR}(T_{\mathrm{Det}})=\max_{V_{\mathrm{GS}},P_{\mathrm{THz}},\Delta f}(\mathrm{SNR}) \tag*{(7)}

Results

Temperature dependent study at 540 GHz

Figure 7 summarizes the results of a TDetT_{\mathrm{Det}}-dependent study of patch-antenna coupled detectors resonating at 540 GHz. Down to 20 K, we do not see indications of strong device degradation due to carrier freezeout-related effects - which is often observed in Si-MOSFETs in this temperature range - in both IV-characteristic and THz-responsivity. We attribute this effect primarily to efficient substrate potential-pinning by the strongly doped p+p^{+}-well placed in close proximity around the nn-MOSFET (see Figure 1). In addition, the II-VV-characteristic shows the Zero-Temperature-Coefficient (ZTC) point (see [56]) at approximately 0.7 V. Above this bias point, a temperature-independent RDSR_{\mathrm{DS}} can be observed. NEP continuously improves (increases) as the temperature reduces, as a result of decreasing (thermal) noise contributions and increasing responsivity RV,CS\mathcal{R}_{V,\mathrm{CS}}. At 20 K, a relative decrease in NEPCS,JN_{\mathrm{CS,JN}} by a factor of 11 to 15 compared to room-temperature operation was observed in the characterization of three independent detectors. At 77 K, we found a relative decrease in NEPCS,JN_{\mathrm{CS,JN}} by a factor of 4–6, compared to room-temperature, which is consistent with previously reported results for Si-CMOS TeraFETs implemented in 90-nm technology [28].9 One should note that the approximately fourfold improvement in NEP around the boiling temperature of LN2_2 can be predicted by applying Eq. (1) to the DC data presented in Figure 7.10 For the 20 K results, Eq. (1) predicts an NEP reduction factor of ∼8\sim8, while the experimental reduction factor was ∼14\sim14.

Figure 7. (a) II–VV characteristics of single-patch detector in a 20–300 K temperature range, measured for VDS±10 mVV_{\mathrm{DS}} \pm10\,\mathrm{mV}. (b) The RDS(VGS,TDet)R_{\mathrm{DS}}(V_{\mathrm{GS}},T_{\mathrm{Det}})-behavior, calculated from the II–VV characteristics. (c–d) Rectified raw terahertz signal measured with a LIA at focal center position and corresponding optical responsivity at 540 GHz. (e–f) Cross-sectional responsivity and corresponding NEPCS,JN_{\mathrm{CS,JN}}.

Nitrogen cooled system at 2.85 THz

Figure 8 shows the detector’s optical responsivity and NEP as function of VGSV_{\mathrm{GS}} at the focus of a 2.85 THz-QCL (5 % duty-cycle pulses). The NEP is shown to decrease by a factor of 3.5 (950 pW/Hz\sqrt{\mathrm{Hz}} vs. 270 pW/Hz\sqrt{\mathrm{Hz}}) when the detector is cooled from 300 K and 77 K. Figure 8(b) presents the results obtained using a 50 % duty-cycle pulse.

Optical voltage responsivity and NEP of detector system as a function of $V_{\mathrm{GS}}$

Figure 8. Optical voltage responsivity and NEP of detector system as a function of VGSV_{\mathrm{GS}}, using a 2.85 THz-QCL source operating at TQCL=20T_{\mathrm{QCL}} = 20 K. (a) Room-temperature vs. LN2_2-cooled detector operation, with QCL parameters: 5 %-duty cycle, fmod=10f_{\mathrm{mod}} = 10 kHz, IQCL,on=700I_{\mathrm{QCL,on}} = 700 mA). (b) Cooled detector operation with QCL parameters: 50 % duty cycle, fmod=2f_{\mathrm{mod}} = 2 kHz, IQCL,on=808I_{\mathrm{QCL,on}} = 808 mA). The experimental noise at different VGSV_{\mathrm{GS}}-potentials was determined under the same laboratory conditions.

In addition to NEPJN,opt_{\mathrm{JN,opt}}, we report the experimental optical NEP (NEPexp_{\mathrm{exp}}), calculated from the total system noise measured under laboratory conditions. The minimum values are NEPopt,JN≈190 pW/Hz_{\mathrm{opt,JN}} \approx190\,\mathrm{pW}/\sqrt{\mathrm{Hz}} and NEPopt,exp≈420 pW/Hz_{\mathrm{opt,exp}} \approx420\,\mathrm{pW}/\sqrt{\mathrm{Hz}}. The minimum NEPopt,exp_{\mathrm{opt,exp}} corresponds to an experimental DNR of approximately 64 dB (PTHz=2.1 mWP_{\mathrm{THz}} = 2.1\,\mathrm{mW}, TC=100 msT_{\mathrm{C}} = 100\,\mathrm{ms}) and up to 67 dB for a detection bandwidth of Δf=1 Hz\Delta f = 1\,\mathrm{Hz}. As shown in Figure 9, a DNR of approximately 70 dB is expected under idealized noise conditions for Δf=1 Hz\Delta f = 1\,\mathrm{Hz}. When directly comparing the results presented in Figure 7 and Figure 8, an important characteristic of the 8 ×\times 8 pixel-embedded detector must be considered (see the derivation in [7]). For N=64N = 64 pixels combined in parallel, the voltage responsivity is reduced by a factor of 64 relative to the cross-sectional responsivity of a single pixel. In contrast, the NEP is expected to increase only by a factor of N=8\sqrt{N} = 8, due to the reduced thermal noise contribution resulting from the parallel network configuration.

Investigation of detector linearity behavior

Figure 9. (a–b) Investigation of detector linearity behavior. VGSV_{\mathrm{GS}}-dependent ΔVDS,LIA\Delta V_{\mathrm{DS,LIA}} (raw data, not corrected for amplifier gain GVG_{\mathrm{V}}) as function of power attenuation (QCL-operation parameters: 50 %-duty cycle, fmod=2f_{\mathrm{mod}} = 2 kHz, IQCL,on=808I_{\mathrm{QCL,on}} = 808 mA, TQCL=20T_{\mathrm{QCL}} = 20 K). (c) Rectified ΔVDS,LIA\Delta V_{\mathrm{DS,LIA}} for differing VGSV_{\mathrm{GS}} indicating linear operation ΔVDS,LIA∝PTHz1\Delta V_{\mathrm{DS,LIA}} \propto P_{\mathrm{THz}}^{1} for VGS>0.2V_{\mathrm{GS}} > 0.2 V. For VGS<0.2V_{\mathrm{GS}} < 0.2 V, super-linear ΔVDS,LIA∝PTHz2\Delta V_{\mathrm{DS,LIA}} \propto P_{\mathrm{THz}}^{2}-behavior occurs.

A study of detector linearity as a function of VGSV_{\mathrm{GS}} for 50 %-duty-cycle QCL pulses is presented in Figure 9. The THz power (PTHz=2.1 mWP_{\mathrm{THz}} = 2.1\,\mathrm{mW}) impinging on the detector was attenuated in 6 dB steps to a maximum of 42 dB attenuation (PTHz≈125 nWP_{\mathrm{THz}} \approx125\,\mathrm{nW}). Due to the high experimental dynamic range exceeding the available dynamic range of the lock-in amplifier (∼40 dB\sim40\,\mathrm{dB}), ΔVDS,LIA,THz,off\Delta V_{\mathrm{DS,LIA,THz,off}} was determined using a lower sensitivity setting, which allowed resolution of the corresponding noise level. The detector shows a linear response for VGS>0.2 VV_{\mathrm{GS}} > 0.2\,\mathrm{V}, while a super-linear response (ΔVDS∝PTHz2\Delta V_{\mathrm{DS}} \propto P_{\mathrm{THz}}^2) occurs for VGS<0.2 VV_{\mathrm{GS}} < 0.2\,\mathrm{V}. This super-linear response can occur in FET-based detectors within the sub-threshold regime as a precursor to saturation, whereas in the above-threshold regime, the detector typically transitions directly into saturation. Due to this nonlinear behavior, a FET operated in this regime can, for example, be used as an autocorrelator [22], [57], [58]. Extrapolation techniques can be employed to determine the minimum detectable power level and the corresponding SNR, which are in good agreement with the prediction based on the experimentally derived NEP (see Eq. (6)). The results further indicate a linear detector response at the recommended operating bias point, approximately 0.6 V, corresponding to the minimum NEP.

Summary and Outline

We have demonstrated a compact, liquid-nitrogen-cooled FET-based THz detector system with strong potential for sensing applications in the 2.8–3.6 THz range. Compared with helium-cooled systems, liquid-nitrogen cooling introduces less operational overhead and is more readily suited to both laboratory and field deployments. Cooling at 77 K is also more readily achievable in satellite instrumentation payloads than 4 K stages. Furthermore, the underlying detector technology can be adapted to operation across a wide range of THz frequencies through application-specific antenna designs. Our results confirm reliable detector operation across a broad temperature

Property/THz-detectorFET 8 × 8 (65-nm Si-CMOS)FET (Al-GaAs/GaAs)Schottky DiodeNbTES bolometerInSb HEBPyroelectric detectorGolay cell
Frequency rangehere 2.8–3.6 THz (Intrinsically 0.1–30 THz, adjustable via different antenna designs)0.1–30 THz covered by broadband antenna (log-spiral)power detection below 1.5 THz, above applications as mixers0.1–30 THz, lowpass filters exist60 GHz to 2.5 THz (>0.5 THz only with magnetic field)up to IR rangeGHz up to IR range
fmod,−3dBf_{\mathrm{mod},-3\mathrm{dB}}DC–5 MHz (limited by readout electronics)not stated (see comment).up to 40 GHz1 kHz0.5 MHz200 Hz20 Hz
DC operationyesyesyes, strong 1/f1/f noisenono informationnono
NEPopt\mathrm{NEP}_{\mathrm{opt}}190 pW/Hz\sqrt{\mathrm{Hz}} at 77 K exp. 420 pW/Hz\sqrt{\mathrm{Hz}}453 nW/Hz\sqrt{\mathrm{Hz}} at 3.08 THz10 pW/Hz\sqrt{\mathrm{Hz}} below 1 THz. Roll-off above1 pW/Hz\sqrt{\mathrm{Hz}}1.5 pW/Hz\sqrt{\mathrm{Hz}}1 nW/Hz\sqrt{\mathrm{Hz}} to 1 μ\muW/Hz\sqrt{\mathrm{Hz}}200 pW/Hz\sqrt{\mathrm{Hz}}
Linear operation range0.4 nW to 2 mW >67 dB, superlinear response available via VGSV_{\mathrm{GS}} variation (e.g. for autocorrelation methods)up to (69 ± 3) dB/1 dB compression point at 0.6 kW at 1.3 THz.around 60 dB1 pW to 10 μ\muW (70 dB)no information1 μ\muW to 5 mW (37 dB)0.2 nW to 100 μ\muW (60 dB)
Operation TemperatureOperable 9–300 K (RT), here 77 K (we expect operability towards lower temperatures, 9 K is limitation of cooling system)RT, 20 K operation shown in [27]RT4 K4 KRTRT
Coupling optics/polarisationNone, Linear polarisation. Optical coupling depends on optical mode profile. Optical elements can be applied to increase performanceSi-lens/Horn-antennaWaveguide integration/Si lens coupled to antenna. Polarisation dependent.Winston cone/no polarisationWinston cone/no polarisationNone/no polarisationNone/no polarisation
Detection mechanismPlasma wavePlasma waveRectification in Diodeelectrothermal feedback at SC-transition (8 K)Hot-electron phenomenonthermalthermal
CommentDetection speed currently limited by applied readout electronics. Spectral response mainly depends on antenna design. Intrinsic effect on 10–20 ps timescale.Implementations mostly applied for high power Free-Electron-Laser (FEL) sensing applications mapping trace of the pulse down to τFWHM=24\tau_{\mathrm{FWHM}} = 24 ps (limited by 30 GHz oscilloscope).Mostly applied as heterodyne mixers above 1.5 THz. NEP not stated above 1.7 THzcommercialcommercialcommercial, absolute power calibration available [54]commercial
References[7], This work[13], [59][60], [61][62][63][54], [64][64], [65]

Table 1. Overview of terahertz power detector systems around 3 THz.

range, from room temperature down to at least 20 K, without observable carrier freeze-out effects — phenomena that are typically expected to limit or inhibit the operation of semiconductor-based detectors at cryogenic temperatures. This thermal robustness presents a key advantage over many conventional THz detectors, which are mostly restricted to narrow temperature windows. Moreover, the detector exhibits continuous improvement in sensitivity (in agreement with the literature) with decreasing temperature, allowing the system to be tailored to the dynamic range requirements of specific experimental conditions.

Although the noise-equivalent power (NEP) of the FET-based system is higher than that of state-of-the-art bolometric detectors, it achieves a comparable linear dynamic range of approximately 67 dB (Δf=1\Delta f = 1 Hz) when used with high-power THz QCL sources (PTHz=2.1P_{\mathrm{THz}} = 2.1 mW). The full dynamic range at the operating point (VGS=0.6V_{\mathrm{GS}} = 0.6 V) could be achieved with the available power, as the detector was still operating linearly. In contrast, highly sensitive bolometers such as Nb-TES typically require attenuation when exposed to similar power levels (e.g., linear regimes between 1 pW and 10–20 µW corresponding to approx

70 dB linear dynamic range). In this context, we emphasize that the reported detector sensitivity is reduced by approximately a factor of 8 due to pixel binning -compared to the respective single detector element under assumption of full power coupling- which was applied to increase the active detector area and achieve higher readout speeds. This approach enables practical, real-world sensing applications without the need for additional coupling elements such as silicon lenses or horn antennas. For resonant single-element TeraFET detectors-typically used in combination with silicon lenses-optical NEPs below 20 pW/Hz\sqrt{\mathrm{Hz}} have been demonstrated at room temperature in the sub-1 THz range. Based on the results previously presented for the sub-1-THz range, we expect the optical NEP of deep-cryogenically (down to 20 K) cooled TeraFETs to reach values of approx. 1.8 pW/Hz\sqrt{\mathrm{Hz}}, comparable to state-of-the-art bolometers, while retaining the FET-detector’s inherently fast detection speed, broad operational temperature range and spectral specificity — properties that are crucial for future terahertz (gas) spectroscopy applications. However, in the frequency range around 3 THz, the NEP behavior at cryogenic temperatures approaching 20 K remains to be investigated in future studies. In the present work at 77 K, optimized for practical applications we observed a relative NEP improvement by a factor of 3.5 compared to room-temperature operation, which is in good agreement with the relative improvement reported in the sub-1 THz range. Unlike conventional (mostly thermal) detectors operating in the 3 THz range (see Table I), which are typically limited to modulation frequencies in the kilohertz range, the realized TeraFET-based system supports significantly higher modulation speeds. In its current implementation, the system bandwidth is primarily limited by the low-noise readout electronics, which are optimized for wideband operation up to several megahertz and for effective suppression of 1/f1/f noise (see Figure 3). On the one hand, this makes the system well suited for DC-true terahertz detection, such as continuous-wave (cw) power monitoring of unmodulated terahertz sources (e.g., THz-QCLs [66] used as local oscillators (LOs) in heterodyne receivers). A DC-true detection scheme refers to reading out the DC rectified voltage (e.g., using a multimeter), which is proportional to the incident terahertz power. This approach reduces the overall instrumentation complexity because no lock-in amplifier is required (compare [30]). On the other hand, the high bandwidth enables time-resolved terahertz gas spectroscopy, capable of tracking transient phenomena on sub-μ\mus timescales. In addition to its demonstrated high linear dynamic range (>64>64 dB, TC=100T_C = 100 ms), the detector can be switched between linear and super-linear (quadratic) response regimes simply by adjusting the gate voltage. This operational flexibility offers significant versatility, making the system suitable for a wide range of experimental applications, including autocorrelation measurements.

Acknowledgments

We thank Dr. Florian Ludwig from Institut Català de Nanociència i Nanotecnologia (ICN2), Barcelona, Spain, previously Physikalisches Insitut (U Frankfurt) for providing access to the ADS-HDM model. We also thank the staff of the institute’s mechanical workshop for their constructive collaboration and for manufacturing custom components used in the cryogenic detector characterization setups.

Data Availability

Data associated with this paper are freely available at the Zenodo Data Repository DOI: https://doi.org/10.5281/zenodo.15865221

Author contributions

J. Holstein: Investigation (lead), Methodology, Software, Validation, Visualization, Data Curation, Writing — original draft; N. K. North: Investigation, Writing — Review and Editing; A. Hof: Investigation; S. S. Kondawar: Investigation; D. B. But: Investigation; M. Salih: Investigation; L. Li: Investigation, Resources; E. H. Linfield: Conceptualization, Funding Acquisition; A. G. Davies: Conceptualization, Funding Acquisition; J. R. Freeman: Conceptualization, Methodology, Investigation, Funding Acquisition, Supervision, Writing — Review and Editing; A. Valavanis: Conceptualization, Methodology, Investigation, Funding Acquisition, Supervision, Writing — Review and Editing; A. Lisauskas: Conceptualization, Methodology, Funding Acquisition, Supervision; H. G. Roskos: Conceptualization, Methodology, Funding Acquisition, Supervision, Writing — Review and Editing.

References

Biographies

Jakob Holstein

Portrait of Jakob Holstein

Figure 10 (PDF p. 13).

Jakob Holstein received first state examination diploma (M.Ed.) for mathematics and physics upper secondary class teaching profession in 2020 from Johann Wolfgang Goethe-University Frankfurt am Main, Germany. In 2021 and 2022, he received B.Sc. and M.Sc. degree in physics from the same university. He is a Ph.D. student in physics in the Ultrafast Spectroscopy and Terahertz Physics Group, Johann Wolfgang Goethe-Universität Frankfurt am Main, Germany. His research interests focus on experimental characterization of Si-CMOS and graphene based TeraFETs for direct power and heterodyne sensing applications. He is working on the realization of integrated TeraFET systems focusing on gas spectroscopy applications.

Nicholas North

Portrait of Nicholas North

Figure 11 (PDF p. 13).

Nicholas North received his M.Eng (Hons) degree and PhD degree in electronic and electrical engineering from the University of Leeds, Leeds, U.K., in 2019 and 2024 respectively. In 2024, he began a research fellow position in the same group. His research focuses on THz high-resolution gas spectroscopy using a QCL as a radiation source and characterising TeraFET detectors with THz QCLs. His research interests are multi-pass optics and sensing atmospheric gas species in the THz spectrum. He is working on THz gas spectroscopy targeting atmospheric chemical reactions and high-sensitivity gas sensing, where fast and sensitive THz detectors are an interest.

Arne Hof

Portrait of Arne Hof

Figure 12 (PDF p. 13).

Arne Hof received his B.Sc. degree in physics in 2024 from the Johann Wolfgang Goethe-University Frankfurt am Main, Germany.

Sanchit Kondawar

Portrait of Sanchit Kondawar

Figure 13 (PDF p. 13).

Sanchit Kondawar received his B.Tech degree in Electronics and Telecommunication Engineering from the Government College of Engineering, Jalgaon, Maharashtra, India, in 2018. He received his M.Sc(Eng.) and Ph.D. degrees in Electronic and Electrical Engineering from the University of Leeds, United Kingdom, in 2019 and 2024, respectively. Currently, he is a Postdoctoral Research Fellow at the School of Electronic and Electrical Engineering at the University of Leeds. His research interests comprises fabrication and characterisation of quantum cascade lasers for high-speed terahertz imaging and ultra-high capacity wireless communications, coherent detection and manipulation, characterisation of integrated photonic devices, and the development of satellite components for integrated terahertz receiver systems.

Dymtro D. But

Portrait of Dymtro D. But

Figure 14 (PDF p. 13).

Dymtro D. But received the Diploma in microelectronics engineering from the Kyiv Polytechnic Institute NTUU, in Ukraine, in 2009 and received his PhD degree in Physics from the Laboratoire Charles Coulomb, the University of Montpellier II in 2014. In 2014, he also worked as an engineer in the Department of Physics and Technology of Low-dimensional Systems at the V.E. Lashkaryov Institute of Semiconductor Physics NAS of Ukraine. Since 2015 he has continued work as an associate researcher in the group of terahertz spectroscopy at the University of Montpellier. Since 2017, he has been working at the Institute of Electrodynamics, Microwave and Circuit Engineering at the Technical University of Wien as a university assistant. Since 2018, he joined a research group at the Institute of High Pressure Physics of the Polish Academy of Sciences. From 2019, he joined CENTERA Project at the same institution. His research interests include condition matter physics, terahertz electronics, systems and semiconductor devices for them.

Mohammed Salih

Portrait of Mohammed Salih

Figure 15 (PDF p. 13).

Mohammed Salih received the M.Sc. and PhD degree in electronic and electrical engineering from the University of Kassel, Kassel, Germany, in 2002, and from the University of Leeds, Leeds, U.K., in 2011, respectively. He works currently as a Senior Research Fellow with the University of Leeds, Leeds, U.K. His research interests include the high power density terahertz quantum cascade lasers and utilizing the terahertz wave in space applications.

Lianhe Li

Portrait of Lianhe Li

Figure 14a.

Lianhe Li received his Ph.D. degree from Institute of Semiconductors, Chinese Academy of Sciences, in 2001. From 2001 to 2003, he was with the Laboratoire de Photonique et des Nanostructures (CNRS), France, working on the low bandgap III-V diluted nitride materials and devices for telecom applications. In 2003, he joined Institute of Photonics and Quantum Electronics, Ecole Polytechnique Fédérale de Lausanne (EPFL, Switzerland), working on the InAs quantum dots for lasers, superluminescent emitting diodes, and single photon devices. Since 2008, he has been with the school of Electronic and Electrical Engineering, University of Leeds (UK), where his research interests focus on the MBE growth and characterization of semiconductor optoelectronic materials and devices for mid-infrared and THz wave generation/detection with particular emphasis on QCLs, QCDs, QWIPs, ICLs, and LT-GaAs.

Edmund Linfield

Portrait of Edmund Linfield

Figure 14b.

Edmund Linfield received the B.A. (Hons.) degree in physics and the Ph.D. degree from the University of Cambridge, Cambridge, U.K., in 1986 and 1991, respectively. He continued his research with the Cavendish Laboratory, University of Cambridge, becoming an Assistant Director of Research and a Fellow of Gonville and Caius College, Cambridge, U.K., in 1997. In 2004, he joined the University of Leeds, Leeds, U.K., to take up the Chair of Terahertz Electronics, and he is currently Director of the University’s ‘Bragg Centre for Materials Research’. He is also ‘Atoms to Devices’ Research Area Lead for the UK’s Royce Institute. His research interests include semiconductor growth and device fabrication, terahertz-frequency optics and electronics, and nanotechnology. Prof. Linfield shared the Faraday Medal and Prize from the Institute of Physics in 2014, and was the recipient of the Wolfson Research Merit Award from the Royal Society in 2015.

Giles Davies

Portrait of Giles Davies

Figure 14c.

A. Giles Davies received the B.Sc. (Hons.) degree in chemical physics from the University of Bristol, Bristol, U.K., in 1987, and the Ph.D. degree in semiconductor physics from the University of Cambridge, Cambridge, U.K., in 1991. In 1991, he joined the University of New South Wales, Sydney, NSW, Australia, supported by an Australian Research Council Fellowship, before returning to the Cavendish Laboratory, University of Cambridge, in 1995, as a Royal Society University Research Fellow, and subsequently Trevelyan Fellow of Selwyn College, Cambridge. Since 2002, he has been with the School of Electronic and Electrical Engineering, University of Leeds, as Professor of Electronic and Photonic Engineering, and is currently also the Deputy Executive Dean, Faculty of Engineering and Physical Sciences. His research interests include the optical and electronic properties of semiconductor devices, terahertz frequency electronics and photonics, and the exploitation of biological properties for nanostructure engineering. Professor Davies is a Fellow of the Royal Academy of Engineering and the Institute of Physics, and both a Chartered Physicist and Chartered Engineer. He was the recipient of the Wolfson Research Merit award from the Royal Society in 2011 and shared the Faraday Medal and Prize from the Institute of Physics in 2014.

Joshua Freeman

Portrait of Joshua Freeman

Figure 14d.

Joshua Freeman received the M.Phys. (Hons.) degree in physics from the University Of Oxford, Oxford, U.K., in 2005, and the Ph.D. degree from the University of Cambridge, Cambridge, U.K., in 2010. In 2010, he started a Postdoctoral Fellowship with the Cavendish, supported by the EPSRC. In 2011, won an individual intra-European fellowship and took up the Marie Curie position at the Ecole Normale Supérieure in Paris, returning to the U.K. to take up a postdoctoral research fellowship at the University of Leeds. In April 2016, he was awarded a “University Academic Fellowship” and is currently Associate Professor at the University of Leeds. His research interests include the design, locking, modulation and coherent detection of quantum cascade lasers, and other optoelectronic terahertz devices.

Alexander Valavanis

Portrait of Alexander Valavanis

Figure 14e.

Alexander Valavanis received the M.Eng. (Hons) degree in electronic engineering from the University of York, York, U.K., in 2004, and the Ph.D. degree in electronic and electrical engineering from the University of Leeds, Leeds, U.K., in 2009. He is an associate professor in terahertz instrumentation at the University of Leeds, Leeds, U.K., and holds a UKRI Future Leader Fellowship. His research interests include terahertz instrumentation, quantum cascade lasers, remote sensing, gas detection, and computational methods for quantum electronics. Dr. Valavanis is a member of the Institution of Engineering and Technology (IET).

Alvydas Lisauskas

Portrait of Alvydas Lisauskas

Figure 14f.

Alvydas Lisauskas Prof. IHPP PAS Alvydas Lisauskas received the Diploma in physics from Vilnius University in 1995, and the PhD degree from the Royal Institute of Technology, Stockholm in 2001. In 2002, he joined the Ultrafast Spectroscopy and Terahertz Physics Group at the Goethe University Frankfurt, Germany, working on novel semiconductor devices for THz applications. From 2014, he is a professor and leading researcher at Vilnius University. From 2014 till 2016 he was a head of joint research laboratory on electrical fluctuations established between the Center for Physical Sciences and Technology and Vilnius University. From 2019 till 2023, he joined CENTERA Project of the Institute of High Pressure Physics PAS, where he led a workgroup on THz electronics.

Harmut G. Roskos

Portrait of Harmut G. Roskos

Figure 16 (PDF p. 15).

Harmut G. Roskos is Professor of Physics at Johann Wolfgang Goethe-University, Frankfurt am Main, Germany. He studied Physics at the Technical University of Karlsruhe (now Karlsruhe Institute of Technology, KIT, Vordiplom 1981) and Technical University of Munich (Dipl. phys. degree, 1985), also receiving the PhD degree from the latter in 1989. He then worked at AT&T Bell Laboratories, Holmdel, USA, where THz phenomena became the focus of his research. He joined the Institute of Semiconductor Electronics of RWTH Aachen in 1991. After receiving the Habilitation degree in Physics from the Faculty of Mathematics and Natural Sciences of RWTH Aachen in 1996 with a thesis on Coherent Phenomena in Solid-State Physics Investigated by THz Spectroscopy, he became a Full Professor at Johann Wolfgang Goethe-Universität in 1997. Current fields of work of his group are time-resolved spectroscopy of solid-state materials (mainly materials with strong electronic correlations), strong light-matter coupling with THz metamaterials, metamaterial sensor development, the development of TeraFETs in various device technologies (including graphene FETs), the development of coherently radiating arrays of resonant-tunneling diodes, THz holographic imaging, and the use of Deep Learning for THz imaging. He spent sabbatical semesters at the University of California at Santa Barbara in 2005 and at the University of Rochester in 2014, and was an Invited Guest Professor at Osaka University’s Institute of Laser Engineering during the winter semester 2009/2010. In 2009, OC Oerlikon AG awarded his group jointly with the Ferdinand-Braun-Institute (FBH) in Berlin a 5-year endowed professorship which led to the establishment of a Joint Lab for THz Photonics.

References

  1. [1]A. Leitenstorfer, A. S. Moskalenko, T. Kamprath, J. Kono, E. Castro-Camus, K. Peng, N. Qureshi, D. Turchinovich, K. Tanaka, A. Markelz, M. Havenith, C. Hough, H. J. Joyce, W. Padilla, B. Zhou, K.-Y. Kim, X.-C. Zhang, P. U. Jepsen, S. Dhillon, M. S. Vitieli, E. H. Linfield, A. G. Davies, M. Hoffmann, R. Lewis, M. Tonouchi, P. Klarskov, T. Seifert, Y. Gerasimenko, D. D. Mihailovic, R. Huber, J. Boland, O. Mitrofanov, P. Dean, B. Ellison, P. Huggard, S. Rea, C. Walker, D. Leisawitz, J. R. Gao, C. Li, Q. Chen, G. Valusis, V. P. Wallace, E. MacPherson, X. Shang, J. Hesler, N. Ridler, C. Renaud, I. Kallfass, T. Nagatsuma, A. Zeitler, D. Arnone, M. Johnston, and J. Cunningham, “The 2023 Terahertz Science and Technology Roadmap,” J. Phys. D: Appl. Phys., Feb. 2023. doi: 10.1088/1361-6463/acbe4c. [Online]. Available: https://iopscience.iop.org/article/10.1088/1361-6463/acbe4cDOI
  2. [2]H.-W. Hübers, H. Richter, and M. Wienold, “High-resolution terahertz spectroscopy with quantum-cascade lasers,” Journal of Applied Physics, vol. 125, no. 15, p. 154101, Apr. 2019. doi: 10.1063/1.5084105. [Online]. Available: http://aip.scitation.org/doi/10.1063/1.5084105
  3. [3]J. W. Waters and P. H. Siegel, “Observing the Stratospheric Submillimeter Spectrum for Detecting Threats to the Ozone Layer,” IEEE J. Microw., vol. 4, no. 4, pp. 791–835, Oct. 2024. doi: 10.1109/JMW.2024.3479080. [Online]. Available: https://ieeexplore.ieee.org/document/10803553/DOI
  4. [4]M. Wienold, A. D. Semenov, E. Dietz, S. Fohmann, P. Dern, X. Lü, L. Schrottke, K. Biermann, B. Klein, and H.-W. Hübers, “OSAS-B: A Balloon-Borne Terahertz Spectrometer for Atomic Oxygen in the Upper Atmosphere,” IEEE Trans. THz Sci. Technol., vol. 14, no. 3, pp. 327–335, May 2024. doi: 10.1109/TTHZ.2024.3363135. [Online]. Available: https://ieeexplore.ieee.org/document/10423795/DOI
  5. [5]G. Savini, D. Brooks, L. Zhu, B. Ellison, O. Auriacombe, T. Bradshaw, M. Crook, D. Gerber, M. Henry, T. Rawlings, H. Wang, J. Charlton, S. M. Tun, M. Emes, T. Hunt, B. Winter, E. Linfield, G. Davies, A. Valavanis, S. Parkes, D. Walker, and G. Yu, “Recent progress in the Elegant Broadband supra-THz activities for LOCUS and a view to an astronomy application,” in 2016 IEEE 9th UK-Euro-China Workshop on Millimetre Waves and Terahertz Technologies (UCMMT). Qingdao, China: IEEE, Sep. 2016, pp. 1–5. doi: 10.1109/UCMMT.2016.7873956. [Online]. Available: http://ieeexplore.ieee.org/document/7873956/DOI
  6. [6]J. R. Wubs, U. Macherelius, K.-D. Weltmann, X. Lü, B. Röben, K. Biermann, L. Schrottke, H. T. Grahn, and J. H. Van Helden, “Terahertz absorption spectroscopy for measuring atomic oxygen densities in plasmas,” Plasma Sources Sci. Technol., vol. 32, no. 2, p. 025006, Feb. 2023. doi: 10.1088/1361-6595/acb815. [Online]. Available: https://iopscience.iop.org/article/10.1088/1361-6595/acb815DOI
  7. [7]J. Holstein, N. K. North, M. D. Horbury, S. Kondawar, I. Kundu, M. Salih, A. Krysl, L. Li, E. H. Linfield, J. R. Freeman, A. Valavanis, A. Lisauskas, and H. G. Roskos, “8×8 Patch-Antenna-Coupled TeraFET Detector Array for Terahertz Quantum-Cascade-Laser Applications,” IEEE Trans. THz Sci. Technol., vol. 14, no. 6, pp. 799–807, Nov. 2024. doi: 10.1109/TTHZ.2024.3438429. [Online]. Available: https://ieeexplore.ieee.org/document/1062338/DOI
  8. [8]W. Knap, V. Kachorovskii, Y. Deng, S. Rumyantsev, J.-Q. Lü, R. Gaska, M. S. Shur, G. Simin, X. Hu, M. A. Khan, C. A. Saylor, and L. C. Brunel, “Nonresonant detection of terahertz radiation in field effect transistors,” Journal of Applied Physics, vol. 91, no. 11, pp. 9346–9353, Jun. 2002. doi: 10.1063/1.1468257. [Online]. Available: https://pubs.aip.org/jap/article/91/11/9346/180449/Nonresonant-detection-of-terahertz-radiation-inDOI
  9. [9]W. Knap, M. Dyakonov, D. Coquillat, F. Teppe, N. Dyakonova, J. Łusakowski, K. Karpierz, M. Sakowicz, G. Valusis, D. Seliuta, I. Kasalynas, A. Fatimy, Y. M. Meziani, and T. Otsuji, “Field Effect Transistors for Terahertz Detection: Physics and First Imaging Applications,” J Infrared Milli Terahz Waves, Aug. 2009. doi: 10.1007/s10762-009-9564-9. [Online]. Available: http://link.springer.com/10.1007/s10762-009-9564-9DOI
  10. [10]A. Lisauskas, U. Pfeiffer, E. Ojefors, P. H. Bolivar, D. Glaab, and H. G. Roskos, “Rational design of high- responsivity detectors of terahertz radiation based on distributed self-mixing in silicon field-effect transistors,” Journal of Applied Physics, vol. 105, no. 11, p. 114511, Jun. 2009. doi: 10.1063/1.3140611. [Online]. Available: https://pubs.aip.org/jap/article/105/11/114511/147534/ Rational-design-of-high-responsivity-detectors-of
  11. [11]S. Boppel, A. Lisauskas, M. Mundt, D. Seliuta, L. Minkevičius, I. Kasalynas, G. Valušis, M. Mittendorff, S. Winnnerl, V. Krozer, and H. G. Roskos, “CMOS Integrated Antenna-Coupled Field-Effect Transistors for the Detection of Radiation From 0.2 to 4.3 THz,” IEEE Trans. Microwave Theory Techn., vol. 60, no. 12, pp. 3834–3843, Dec. 2012. doi: 10.1109/TMTT.2012.2221732. [Online]. Available: http://ieeexplore.ieee.org/document/6353608/DOI
  12. [12]S. Regensburger, S. Preu, A. K. Mukherjee, S. Schonhuber, M. A. Kainz, S. Winnnerl, J. M. Klopf, H. Lu, A. C. Gossard, and K. Unterrainer, “Broadband Terahertz Detection With Zero-Bias Field-Effect Transistors Between 100 GHz and 11.8 THz With a Noise Equivalent Power of 250 pW/sqrt(Hz) at 0.6 THz,” IEEE Trans. THz Technol., vol. 8, no. 4, pp. 465–471, Jul. 2018. doi: 10.1109/TTHZ.2018.2843535. [Online]. Available: https://ieeexplore.ieee.org/document/8371294/
  13. [13]R. Yadav, F. Ludwig, F. R. Faridi, J. M. Klopf, H. G. Roskos, A. Pernișcke, and S. Preu, “GaAs-based antenna-coupled field effect transistors as direct THz detectors across a wide frequency range from 0.2 to 29.8 THz,” Opt. Express, vol. 32, no. 24, p. 43407, Nov. 2024. doi: 10.1364/OE.534393. [Online]. Available: https://opg.optica.org/abstract.cfm?URI=oe-32-24-43407
  14. [14]H. Yuan, D. Vof, A. Lisauskas, D. Mundy, and H. G. Roskos, “3D Fourier imaging based on 2D heterodyne detection at THz frequencies,” APL Photonics, vol. 4, no. 10, p. 106108, Oct. 2019. doi: 10.1063/1.5116553. [Online]. Available: https://pubs.aip.org/app/article/4/10/106108/1065284/3D-Fourier-imaging-based-on-2D-heterodyneDOI
  15. [15]S. Boppel, A. Lisauskas, A. Max, V. Krozer, and H. G. Roskos, “CMOS detector arrays in a virtual 10-kilopixel camera for coherent terahertz real-time imaging,” Opt. Lett., vol. 37, no. 4, p. 536, Feb. 2012. doi: 10.1364/OL.37.000536. [Online]. Available: https://opg.optica.org/abstract.cfm?URI=ol-37-4-536DOI
  16. [16]A. Lisauskas, M. Bauer, S. Boppel, M. Mundt, B. Khamaisi, E. Socher, R. Venckevičius, L. Minkevičius, I. Kašalynas, D. Seliuta, G. Valušis, V. Krozer, and H. G. Roskos, “Exploration of Terahertz Imaging with Silicon MOSFETs,” J Infrared Milli Terahz Waves, vol. 35, no. 1, pp. 63–80, Jan. 2014. doi: 10.1007/s10762-013-0047-7. [Online]. Available: http://link.springer.com/10.1007/s10762-013-0047-7DOI
  17. [17]G. Valušis, A. Lisauskas, H. Yuan, W. Knap, and H. G. Roskos, “Roadmap of Terahertz Imaging 2021,” Sensors, vol. 21, no. 12, p. 4092, Jun. 2021. doi: 10.3390/s21124092. [Online]. Available: https://www.mdpi.com/1424-8220/21/12/4092DOI
  18. [18]M. Bauer, R. Venckevičius, I. Kašalynas, S. Boppel, M. Mundt, L. Minkevičius, A. Lisauskas, G. Valušis, V. Krozer, and H. G. Roskos, “Antenna-coupled field-effect transistors for multi-spectral terahertz imaging up to 425 THz,” Opt. Express, vol. 22, no. 16, p. 19235, Aug. 2014. doi: 10.1364/OE.22.019235. [Online]. Available: https://opg.optica.org/oe/abstract.cfm?uri=oe-22-16-19235
  19. [19]A. Krysl, D. B. But, K. Ikamas, J. Holstein, A. Shevchik-Sheker, H. G. Roskos, and A. Lisauskas, “Si Superstrate Lenses on Patch-Antenna-Coupled TeraFETs: NEP Optimization and Frequency Fine-Tuning,” IEEE Sensors J., vol. 24, no. 21, pp. 33872–33880, Nov. 2024. doi: 10.1109/JSEN.2024.3445140. [Online]. Available: https://ieeexplore.ieee.org/document/10666089/DOI
  20. [20]M. D. Horbury, N. K. North, J. Holstein, H. Godden, L. H. Li, J. R. Freeman, E. H. Linfield, H. Roskos, A. Lisauskas, and A. Valavanis, “Real-Time Terahertz Absorption Spectroscopy of Methanol and Deuterated-Methanol Vapour, using a TeraFET Detector Array,” in 2023 48th International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz). Montreal, QC, Canada: IEEE, Sep. 2023, pp. 1–2. doi: 10.1109/IRMMW-THz57677.2023.10298916. [Online]. Available: https://ieeexplore.ieee.org/document/10298916/DOI
  21. [21]S. Preu, M. Mittendorff, S. Winnerl, H. Lu, A. C. Gossard, and H. B. Weber, “Ultra-fast transistor-based detectors for precise timing of near infrared and THz signals,” Opt. Express, vol. 21, no. 15, p. 17941, Jul. 2013. doi: 10.1364/OE.21.017941. [Online]. Available: https://opg.optica.org/oe/abstract.cfm?uri=oe-21-15-17941DOI
  22. [22]A. Lisauskas, K. Ikamas, S. Massabeau, M. Bauer, D. Čibiraitė, J. Matukas, J. Mangeney, M. Mittendorff, S. Winnerl, V. Krozer, and H. G. Roskos, “Field-effect transistors as electrically controllable nonlinear rectifiers for the characterization of terahertz pulses,” APL Photonics, vol. 3, no. 5, p. 051705, May 2018. doi: 10.1063/1.5011392. [Online]. Available: https://pubs.aip.org/app/article/3/5/051705/1024619/Field-effect-transistors-as-electricallyDOI
  23. [23]D. Čibiraitė Lukenskienė, K. Ikamas, T. Lisauskas, V. Krozer, H. G. Roskos, and A. Lisauskas, “Passive Detection and Imaging of Human Body Radiation Using an Uncooled Field-Effect Transistor-Based THz Detector,” Sensors, vol. 20, no. 15, p. 4087, Jul. 2020. doi: 10.3390/s20154087. [Online]. Available: https://www.mdpi.com/1424-8220/20/15/4087DOI
  24. [24]M. Andree, J. Grzyb, H. Rücker, and U. R. Pfeiffer, “Towards Passive Imaging With Uncooled, Low-NEP SiGe HBT Terahertz Direct Detectors,” IEEE Trans. THz Sci. Technol., vol. 14, no. 5, pp. 632–651, Sep. 2024. doi: 10.1109/TTHZ.2024.3432619. [Online]. Available: https://ieeexplore.ieee.org/document/10607950/DOI
  25. [25]D. Glaab, S. Boppel, A. Lisauskas, U. Pfeiffer, E. Ojefors, and H. G. Roskos, “Terahertz heterodyne detection with silicon field-effect transistors,” Applied Physics Letters, vol. 96, no. 4, p. 042106, Jan. 2010. doi: 10.1063/1.3292016. [Online]. Available: https://pubs.aip.org/apl/article/96/4/042106/131998/Terahertz-heterodyne-detection-with-silicon-fieldDOI
  26. [26]J. Grzyb and U. Pfeiffer, “THz Direct Detector and Heterodyne Receiver Arrays in Silicon Nanoscale Technologies,” J Infrared Milli Terahz Waves, vol. 36, no. 10, pp. 998–1032, Oct. 2015. doi: 10.1007/s10762-015-0172-6. [Online]. Available: http://link.springer.com/10.1007/s10762-015-0172-6DOI
  27. [27]O. A. Klimenko, W. Knap, B. Iniguez, D. Coquillat, Y. A. Mityagin, F. Teppe, N. Dyakonova, H. Videlier, D. But, F. Lime, J. Marczevski, and K. Kucharski, “Temperature enhancement of terahertz responsivity of plasma field effect transistors,” Journal of Applied Physics, vol. 112, no. 1, p. 014506, Jul. 2012. doi: 10.1063/1.4733465. [Online]. Available: https://pubs.aip.org/jap/article/112/1/014506/213433/Temperature-enhancement-of-terahertz-responsivityDOI
  28. [28]K. Ikamas, A. Solovjovas, D. Cibiraite-Lukenskiene, V. Krozer, A. Lisauskas, and H. G. Roskos, “Optical Performance of Liquid Nitrogen Cooled Transistor-Based THz Detectors,” in 2020 45th International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz). Buffalo, NY, USA: IEEE, Nov. 2020, pp. 1–1. doi: 10.1109/IRMMW-THz46771.2020.9370863. [Online]. Available: https://ieeexplore.ieee.org/document/9370863/DOI
  29. [29]M. Bauer, A. Ramer, S. A. Chetverchenko, K. Y. Osipov, D. Cibiraite, S. Pralgauskaite, K. Ikamas, A. Lisauskas, W. Heinrich, V. Krozer, and H. G. Roskos, “A High-Sensitivity AlGaN/GaN HEMT Terahertz Detector With Integrated Broadband Bow-Tie Antenna,” IEEE Trans. THz Sci. Technol., vol. 9, no. 4, pp. 430–444, Jul. 2019. doi: 10.1109/TTHZ.2019.2917782. [Online]. Available: https://ieeexplore.ieee.org/document/8734725/DOI
  30. [30]J. Zdanevicius, D. Cibiraite, K. Ikamas, M. Bauer, J. Matukas, A. Lisauskas, H. Richter, T. Hagelschuer, V. Krozer, H.-W. Hubers, and H. G. Roskos, “Field-Effect Transistor Based Detectors for Power Monitoring of THz Quantum Cascade Lasers,” IEEE Trans. THz Sci. Technol., vol. 8, no. 6, pp. 613–621, Nov. 2018. doi: 10.1109/TTHZ.2018.2853600. [Online]. Available: https://ieeexplore.ieee.org/document/8536434/
  31. [31]K. Ikamas, D. B. But, A. C. Celi, C. Kolačinski, T. Lisauskas, W. Knap, and A. Lisauskas, “All-Electronic Emitter-Detector Pairs for 250 GHz in Silicon,” Sensors, vol. 21, no. 17, p. 5795, Aug. 2021. doi: 10.3390/s21175795. [Online]. Available: https://www.mdpi.com/1424-8220/21/17/5795DOI
  32. [34]E. Javadi, D. B. But, K. Ikamas, J. Zdanevičius, W. Knap, and A. Lisauskas, “Sensitivity of Field-Effect Transistor-Based Terahertz Detectors,” Sensors, vol. 21, no. 9, p. 2909, Apr. 2021. doi: 10.3390/s21092909. [Online]. Available: https://www.mdpi.com/1424-8220/21/9/2909DOI
  33. [35]A. Cesiul, K. Ikamas, D. B. But, I. Morkūnaitė, T. Lisauskas, and A. Lisauskas, “Towards wireless data transmission with compact all-electronic THz source and detector system,” physics, vol. 62, no. 3, Oct. 2022. doi: 10.3952/physics.v62i3.4796. [Online]. Available: https://www.lmaleidykla.lt/ojs/index.php/physics/article/view/4796DOI
  34. [36]A. A. Generalov, M. A. Andersson, X. Yang, A. Vorobiev, and J. Stake, “A 400-GHz Graphene FET Detector,” IEEE Trans. THz Sci. Technol., vol. 7, no. 5, pp. 614–616, Sep. 2017. doi: 10.1109/TTHZ.2017.2722360. [Online]. Available: http://ieeexplore.ieee.org/document/7981343/DOI
  35. [39]J. Holstein, R. Kapoor, J. A. Delgado Notario, V. Clericò, F. Ludwig, and H. G. Roskos, “Towards efficient and sensitive room-temperature THz detection using state-of-the-art broadband graphene/hBN-based TeraFETs,” in 2024 49th International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz). Perth, Australia: IEEE, Sep. 2024, pp. 1–2. doi: 10.1109/IRMMW-THz60956.2024.10697713. [Online]. Available: https://ieeexplore.ieee.org/document/10697713/DOI
  36. [40]E. Ojofors, U. R. Pfeiffer, A. Lisauskas, and H. G. Roskos, “A 0.65 THz Focal-Plane Array in a Quarter-Micron CMOS Process Technology,” IEEE J. Solid-State Circuits, vol. 44, no. 7, pp. 1968–1976, Jul. 2009. doi: 10.1109/JSSC.2009.2021911. [Online]. Available: http://ieeexplore.ieee.org/document/5109781/
  37. [42]M. Liu, Z. Cai, J. Liu, N. Wu, and L. Liu, “Exploration of high-speed 3.0 THz imaging with a 65 nm CMOS process,” J. Semicond., vol. 44, no. 10, p. 102401, Oct. 2023. doi: 10.1088/1674-4926/44/10/102401. [Online]. Available: https://iopscience.iop.org/article/10.1088/1674-4926/44/10/102401DOI
  38. [43]R. Jain, R. Zatta, J. Grzyb, D. Harame, and U. Pfeiffer, “A Terahertz Direct Detector in 22nm FD-SOI CMOS,” 2018 13th European Microwave Integrated Circuits Conference (EuMIC), pp. 25–28, 2018. doi: 10.23919/EuMIC.2018.8539908., publisher: Bergische Universität Wuppertal. [Online]. Available: https://epub.uni-wuppertal.de/recieve/dupublico_mods_00000754DOI
  39. [45]Antenna-coupled field-effect transistors as detectors for terahertz near-field microscopy,” Nanoscale Adv., vol. 3, no. 6, pp. 1717–1724, 2021. doi: 10.1039/D0NA00928H. [Online]. Available: http://xlink.rsc.org/?DOI=D0NA00928HDOI
  40. [46]R. Yadav, F. Ludwig, F. R. Faridi, J. M. Klopf, H. G. Roskos, S. Preu, and A. Pernisrcke, “State-of-the-Art Room Temperature Operable Zero-Bias Schottky Diode-Based Terahertz Detector Up to 5.56 THz,” Sensors, vol. 23, no. 7, p. 3469, Mar. 2023. doi: 10.3390/s23073469. [Online]. Available: https://www.mdpi.com/1424-8220/23/7/3469DOI
  41. [47]M. Shur, T. Fjeldly, T. Ytterdal, and K. Lee, “Unified MOSFET model,” Solid-State Electronics, vol. 35, no. 12, pp. 1795–1802, Dec. 1992. doi: 10.1016/0038-1101(92)90263-C. [Online]. Available: https://linkinghub.elsevier.com/retrieve/pii/003811019290263CDOI
  42. [48]F. Ludwig, J. Holstein, A. Krysl, A. Lisauskas, and H. G. Roskos, “Modeling of Antenna-Coupled Si MOSFETs in the Terahertz Frequency Range,” IEEE Trans. THz Sci. Technol., vol. 14, no. 3, pp. 414–423, May 2024. doi: 10.1109/TTHZ.2024.3388254. [Online]. Available: https://ieeexplore.ieee.org/document/10497872/DOI
  43. [49]A. Lisauskas, S. Boppel, J. Matukas, V. Palenskis, L. Minkevicius, G. Valušis, P. Haring-Bolívar, and H. G. Roskos, “Terahertz responsivity and low-frequency noise in biased silicon field-effect transistors,” Appl. Phys. Lett., vol. 102, no. 15, p. 153505, Apr. 2013. doi: 10.1063/1.4802208. [Online]. Available: https://pubs.aip.org/aip/apl/article/125983DOI
  44. [50]F. Ludwig, H. G. Roskos, and R. Borsche, “2-D Hydrodynamic Simulation of TeraFETs Beyond the Gradual-Channel Approximation for Transient, Large-Signal, or Ultrahigh-Frequency Simulations,” IEEE Trans. Electron Devices, pp. 1–9, 2025. doi: 10.1109/TED.2025.3558157. [Online]. Available: https://ieeexplore.ieee.org/document/10965757/DOI
  45. [51]F. Ludwig, M. Bauer, A. Lisauskas, and H. G. Roskos, “Circuit-Based Hydrodynamic Modeling of AlGaN/GaN HEMTs,” in ESSDERC 2019 - 49th European Solid-State Device Research Conference (ESSDERC). Cracow, Poland: IEEE, Sep. 2019, pp. 270–273. doi: 10.1109/essderc.2019.8901683. [Online]. Available: https://ieeexplore.ieee.org/document/8901683/DOI
  46. [52]M. Wienold, L. Schrottke, M. Giehler, R. Hey, W. Anders, and H. Grahn, “Low-voltage terahertz quantum-cascade lasers based on LO-phonon-assisted interminiband transitions,” Electron. Lett., vol. 45, no. 20, pp. 1030–1031, Sep. 2009. doi: 10.1049/el.2009.1371. [Online]. Available: http://digital-library.theiet.org/doi/10.1049/el.2009.1371DOI
  47. [53]T. Instruments, “JFE2140 Ultra-Low Noise, Matched, Dual, Low-Gate Current, Discrete, Audio, N-Channel JFET,” 2023. [Online]. Available: https://www.ti.com/product/JFE2140
  48. [54]S. S. und Lasertechnik GmbH, “PTB-calibrated Pyroelectric detector THz 20 HS,” 2025. [Online]. Available: https://www.pyrosensor.de/High-Sensitive-922643.html
  49. [55]AMETEK ADVANCED MEASUREMENT TECHNOLOGY, INC, “Model 7265 DSP Lock-in Amplifier - Instruction Manual,” 2002.
  50. [56]R. Saligram, A. Raychowdhury, and S. Datta, “The future is frozen: cryogenic CMOS for high-performance computing,” Chip, vol. 3, no. 1, p. 100082, Mar. 2024. doi: 10.1016/j.chip.2023.100082. [Online]. Available: https://linkinghub.elsevier.com/retrieve/pii/S270947232300045XDOI
  51. [57]K. Ikamas, A. Lisauskas, M. Massabeau, M. Bauer, M. Burakevič, J. Vyšniauskas, D. Čibiraitė, V. Krozer, A. Rämer, S. Shevchenko, W. Heinrich, J. Tignon, S. Dhillon, J. Mangeney, and H. G. Roskos, “Sub-picosecond pulsed THz FET detector characterization in plasmonic detection regime based on autocorrelation technique,” Semicond. Sci. Technol., vol. 33, no. 12, p. 124013, Dec. 2018. doi: 10.1088/1361-6641/aae905. [Online]. Available: https://iopscience.iop.org/article/10.1088/1361-6641/aae905DOI
  52. [58]K. Ikamas, I. Nevinskas, A. Krotkus, and A. Lisauskas, “Silicon Field Effect Transistor as the Nonlinear Detector for Terahertz Autocorrelators,” Sensors, vol. 18, no. 11, p. 3735, Nov. 2018. doi: 10.3390/s18113735. [Online]. Available: https://www.mdpi.com/1424-8220/18/11/3735DOI
  53. [59]S. Regensburger, M. Mittendorff, S. Winnerl, H. Lu, A. C. Gossard, and S. Preu, “Broadband THz detection from 01 to 22 THz with large area field-effect transistors,” Opt. Express, vol. 23, no. 16, p. 20732, Aug. 2015. doi: 10.1364/OE.23.020732. [Online]. Available: https://opg.optica.org/abstract.cfm?URI=oe-23-16-20732
  54. [60]I. Mehdi, J. V. Siles, C. Lee, and E. Schlecht, “THz Diode Technology: Status, Prospects, and Applications,” Proc. IEEE, vol. 105, no. 6, pp. 990–1007, Jun. 2017. doi: 10.1109/JPROC.2017.2650235. [Online]. Available: http://ieeexplore.ieee.org/document/7835091/DOI
  55. [61]{Virginia Diodes, Inc.}, “Zero Bias Detector (ZBD),” Jul. 2025. [Online]. Available: https://www.vadiodes.com/en/products/detectors
  56. [62]{QMC Instruments Ltd.}, “Superconducting Bolometer (NbTES),” 2025. [Online]. Available: https://www.qmcinstruments.co.uk/superconducting-bolometer-nbtes/
  57. [63]——, “InSb Hot Electron Bolometer,” 2025. [Online]. Available: https://www.qmcinstruments.co.uk/insb-hot-electron-bolometer/
  58. [64]Z. Bielecki, J. Mikolajczyk, and J. Wojtas, “A Review of Thermal Detectors of THz Radiation Operated at Room Temperature,” Sensors, vol. 24, no. 21, p. 6784, Oct. 2024. doi: 10.3390/s24216784., publisher: MDPI AG. [Online]. Available: https://www.mdpi.com/1424-8220/24/21/6784DOI
  59. [65]TYDEX, “Golay detectors,” 2025. [Online]. Available: https://www.tydexoptics.com/products/thz_devices/golay_cell/
  60. [66]J. Holstein, N. Rothbart, M. Wienold, A. Lisauskas, H.-W. Hübers, and H. G. Roskos, “Comparison Of Single-pixel, 4x4-And 8x8-binned Patch-antenna-coupled TeraFET Detectors For 4.7-THz QCL Applications,” in 2025 50th International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz). Espoo, Finland: IEEE, Sep. 2025, pp. 1–2.

Paper details

vlnc:W_eau9duaq
Version
v1 · latest
Published
Fresh — added to the Hub within the last 30 days
Added
License
CC BY 4.0
Usage

views · 0

downloads · 0

A view counts once per browser per day, a download each time the PDF is requested.

  • Physics and Astronomy

Not recorded for this paper

View statement
Looking for related papers…
Contents